Oper Manual Gbf-50-Vh

GBF50VH
Operations & Service Manual Ventless Electric Fryer
ISO 9001 Registered • Committed to Quality

2750 Gunter Park Drive West • Montgomery, AL 36109 USA
Phone: 334.272.1457 • Toll Free: 800.554.4537 (USA & Canada Only)
Fax: 334.239.4117 • Website: www.gfse.com
Printed in USA, Form No. 66317 (Rel. Date: Aug.2019, Rev. A)

LIMITED WARRANTY
• Subject to the terms and conditions of this Limited Warranty as herein stated, all Giles Enterprises Inc.
(hereafter referred to as “Giles”) food service equipment and parts purchased new from an authorized Giles
representative are warranted as to defects in material or workmanship for a period of twentyfour (24)
months from the date of installation, provided, however, that with regard to labor costs in connection with
this warranty, see below. All installations must be made by a qualified installing agency in accordance with
all applicable codes and/or regulations in the jurisdiction in which installed. Limited warranty coverage is
extended only to the original owner and is void if the unit is resold.
• During the Limited Warranty period, Giles will replace or recondition, at its factory, any part or parts of this
unit which Giles inspectors judge defective, provided the unit has been properly installed, subjected to
normal usage, and operated and maintained in accordance with specified procedures. This Limited Warranty
does not cover cosmetic damage, and damage due to acts of God, accident, misuse, alteration, negligence,
abuse, or use of unorthodox repair methods. All parts replaced under this Limited Warranty carry only the
unexpired term of this Limited Warranty. Limited Warranty service may be furnished only by an authorized
Giles service representative.
• If Limited Warranty service is requested, Giles will dispatch factoryauthorized service representatives to
inspect, repair, recondition, or replace units of its manufacture with such labor being rendered without cost
to owner for twentyfour (24) months from the date of installation. Otherwise, service, including labor and
transportation charges or other expenses, in connection with the removal or installation of any part or parts
supplied under this Limited Warranty, are specified on the original sales contract between the purchaser and
the authorized Giles representative.
• Failure to use Giles OEM replacement parts and Giles OEM filters may void this Warranty.
• Giles reserves the right to change or improve its equipment and/or parts in any way without obligation to
alter such equipment or parts previously manufactured.
• Giles makes no further warranties, express or implied, including implied warranties of merchantability or
fitness for a particular purpose, and has no other obligation or liability not specifically stated herein.
• Repair or replacement as provided under this limited warranty is the exclusive remedy. Giles shall not be
liable for any incidental or consequential damages for breach of any express or implied warranty on this
product, except to the extent prohibited by applicable law. Any implied warranty of merchantability or
fitness for a particular purpose on this product is limited in duration to the duration of this limited warranty.
• Used Giles foodservice equipment or parts, or Giles foodservice equipment or parts not purchased from an
authorized Giles representative, carry no warranties, express or implied.
Table Of Contents GBF50VH Electric Fryer
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Safety Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Specific Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.01 Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.02 Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.02.1 Optional Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.03 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.03.1 Overall Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.03.2 Agency Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.03.3 Basket Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.03.4 Vat Size and Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.03.5 Shipping Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.01 Appliance Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.02 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.03 Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.04 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.05 Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.05.1 Electrical Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.06 Ventless Hood Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.07 Ventless Hood Fire Suppression System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.08 Fusible Link Detector & Gas Cartridge Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.09 Fire Extinguisher Nozzle & Tank Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10 Fire Alarm Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.11 Finalizing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.11.1 Power Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.11.2 Heat Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.11.3 Filter Pump Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.11.4 Initial Fryer Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.11.5 Optional KITCHENTRAC™ Remote Equipment Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3. Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.01 Baskets & Basket Lifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.02 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.03 Lower Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.04 Filter Pan Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.05 Ventless Hood. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.06 Accessories Provided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.07 Accessories Not Provided . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
iii
GBF50VH Electric Fryer Table Of Contents
4. Fryer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.01 Computer Controller Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.01.1 Keys and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.01.2 Controller General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.01.3 Setting the Cooking Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
4.01.4 Manually Setting the Cook Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.01.5 Working with Menu Item Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
4.01.5.1 Editing a Menu Item Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4.01.5.2 Selecting a Menu Item Preset for Cooking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.01.6 Cooking Cycle General Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
4.01.7 Other Controller Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.01.7.1 Manually Operating the Basket Lifts (if equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.01.7.2 COOL Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.01.7.3 AUTOCOOL Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.01.7.4 BOIL OUT mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
4.01.8 User Settings (Accessing & Editing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.01.9 PASSWORD Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.01.10 Powerup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.01.11 Controller Errors and Alarms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.01.11.1 Clearing Controller Errors & Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.02 Cooking Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.02.1 Filling & Preparing Fryer for Cooking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.02.2 Loading Fryer for Cooking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.02.3 Cooking Cycle Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.03 Filtering Used Cooking Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.04 Fryer ShutDown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
5. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.01 Removing Waste Cooking Oil from Fryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.02 BoilOut Procedure Cleaning the Vat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.03 Cleaning the Filter Pan & Refreshing Filter Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6. Ventless Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6.01 Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6.01.1 Ventless Hood Filter Tabler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
6.01.2 Filter Removal & Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
6.02 E.A.C. Filter Operation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
6.02.1 E.A.C. Filter Cell Cleaning Timer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
6.03 Baffle Filter Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.04 E.A.C. Filter Cell Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6.05 Charcoal Filter Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.06 Filter Alarm Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
6.07 Hood Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.07.1 Monthly Hood Interlock Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
6.02.2 Quarterly Hood Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
6.02.3 SemiAnnual Fire System Inspection & Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
iv
Table Of Contents GBF50VH Electric Fryer
6.02.4 Annual Fire System Inspection & Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

6.02.5 12Year Fire System Inspection & Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
6.02.6 Maintenance & Service Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
7. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.01 Temperature Control System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.02 Oil Filtration System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
7.03 AutoBasket Lift System (if equipped) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
8. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8.01 Ordering & Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
8.02 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
8.03 Control Assembly Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
8.04 Lower Cabinet Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
8.05 Lower Cabinet Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
8.06 Cook Vat Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8.07 Ventless Hood & Fryer Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
8.08 Ventless Hood Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
8.09 Ventless Hood Filter Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
8.10 Filter Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Appendix A. Connecting Optional KITCHENTRAC™ . . . . . . . . . . . . . . . . . . . . . . . . . . 111

A.1 Connecting WIFI Board to Wireless Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
A.2 Estsablishing Communication with KITCHENTRAC™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
A.3 WIFI Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
v
GBF50VH Electric Fryer Safety
Safety Overview:
The instructions contained in this manual have been prepared to aid in learning the proper procedures for installing,
operating and servicing the Giles Model GBF‐50‐VH Ventless Electric Fryer.
Throughout the manual, safety precautions are identified by a hazard alert symbol and key words such as DANGER,
WARNING or CAUTION. Alert information precedes the tasks to which it applies. Suggested, recommended, or other
noteworthy information is identified as NOTES, or will be noted as IMPORTANT!. Additionally, certain words are used to
indicate a specific meaning, or to add emphasis as follows:
Shall: understood to be mandatory.
Should: understood to be advisory.
May: understood to be permissive.
Will: indicates a future event or condition to occur.
Hazard Alert Symbols are used in conjunction with key words, such as DANGER, WARNING, or CAUTION, to
alert users to potential personal injury hazards and/or poor operating practices. These will immediately precede
precautionary measures pertaining to avoiding such hazards or practices. Adhere to all information following these
symbols to avoid possible injury, or even death. Failure to do so may also void the factory warranty.
This product can expose users to lead, nickel, aluminum, brass, carbon or copper which are known in the state of
California to cause cancer, birth defects and other reproductive harm. For more information go to:
www.p65warnings.ca.gov.
Indicates an imminently hazardous situation which, if not avoided, will result in serious personal injury, even death.
Indicates a potentially hazardous situation which, if not avoided, could result in serious injury, even death.
Indicates a potentially hazardous situation which, if not avoided, may result in minor to moderate injury. This
notification is also used as an alert to unsafe practices.
If used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, may result in
equipment and/or property damage, and may void the factory warranty.
NOTE or IMPORTANT!
Identifies suggested, recommended, or other important information.
vi
Safety GBF50VH Electric Fryer
Specific Safety Precautions:
For your safety, please observe the following precautions when operating or servicing this appliance. Adhering to the
following important safety precautions will help to avoid personal injury and/or damage to the equipment or property.
• Before cleaning or performing maintenance, place power switch in the [OFF] position. To remove all power
from unit, either unplug power cord or turn OFF power at the electrical panel supplying power to the appliance.
• DO NOT wash down the fryer interior or exterior with water spray. Control panels are “liquid resistant”, but are
not washdown‐safe.
• Failure to comply with DANGER notices will result in serious injury, even death; or damage to equipment and/or
property and may void the factory warranty.
• Cooking appliances with an integral, ventless/recirculating hood are NOT suitable for every commercial food
service application. Failure to fully comply with all site requirements and installation limitations as outlined in the
GFSE Hood Approval Letter and this Manual, may result in poor or highly unsatisfactory air cleaning performance.
It is the purchaser’s responsibility to oversee installation and ensure that all contractors engaged, to perform
installation work, do comply with all installation guidelines and restrictions.
• The unit must be adequately and properly grounded. Improper grounding can result in electrical shock to the user.
Always refer to local electrical code to ensure proper grounding of this or any other electrical equipment.
• Check the rating label on the unit to determine the proper power supply required. Consult with a qualified electrician or
technician to ensure that installation will comply with the unit’s electrical requirements and all local codes, and that
circuit breakers and wiring are of sufficient rating and gauge to power the equipment load. A wiring diagram has been
provided. Appliance must be installed and electrically grounded in accordance with local code, or in the absence of
local code, in accordance with the National Electrical Code, NFPA 70.
• Improper installation, adjustment, alteration, service, or maintenance could result in serious injury, even death;
equipment and/or property damage; and will potentially void the factory warranty.
• DO NOT use or store flammable liquids, or materials that produce flammable vapors, in the vicinity of this or any
other appliance!
• DO NOT (or ALLOW OTHERS to) for any reason, stand or step onto the top of the appliance. Cooking oil
in fryers can be EXTREMELY HOT (excess of 330°F [166°C]). Bodily contact will cause extremely serious
injury. Lids used to sometimes cover cooking vats/pots are not designed to, and WILL NOT, support the
weight of a person.
• Failure to comply with WARNING notices can result in serious injury, even death; damage to equipment and/or
property; and will potentially void the factory warranty.
vii
• The appliance must remain in an upright position.

• Exercise due care when removing the unit from shipping pallet.
• DO NOT operate the appliance, unless you fully understand its components and their intended functions (see Section
3). Closely follow the instructions and procedures presented in this Manual to avoid possible equipment damage or
malfunction.
• To avoid personal injury, it is recommended that thermal hand protection (gloves or mitts) be worn while tended
the appliance. Certain parts of the unit will become very HOT during operation. Temperatures inside the cabinet
may exceed 150°F (65.5°C)! Use due caution when operating and cleaning.
• Placing foods containing excessive moisture into hot oil, or attempting to place quantities of product exceeding
recommended batch sizes, can cause a “surge boil”, resulting in an overflow of HOT oil. Exercise due care when
loading food, proceeding slowly to observe how the oil reacts before continuing.
• Be sure the appliance is positioned in a stable, safe location with casters in the locked position. DO NOT operate
appliance if not secured. Some jurisdictions may require special anchoring for this type appliance; check local code.
• Allow the appliance to cool for 1520 minutes before cleaning or servicing.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge, unless they have been given adequate instruction and/or
supervision concerning its use by a person responsible for their safety. Children should not be allowed to play with,
or around, this appliance.
• Prior to sale and consumption, cooked food products must be maintained at a minimum temperature of 150°F
(65.5°C), or in accordance with governing health regulations.
• Avoid bending collection fins or breaking the ionizer wires on the Electronic Air Cleaner (EAC) Collector Cell. Doing so
will prevent the EAC from working properly, and may cause the fryer to shutdown.
• After cleaning the EAC Cell, DO NOT attempt to dry it by installing it in the fryer hood and running the blower to force
air dry it, or by heating the fryer. Energizing EAC cell while wet will potentially damage the EAC power supply and
control system, leading to malfunction and voiding the warranty. The cell must air dry at ambient room temperature,
preferably overnight. Setting up a small fan to blow air through it can help expedite drying.
• Failure to comply with CAUTION notices may result in minor to moderate personal injury, damage to equipment or
property, and potentially void the warranty.
viii
Safety GBF50VH Electric Fryer
• Components exposed on the control panel surface are impactsensitive. To avoid damage and maintain proper
operation, exercise care when working around or using carts/rolling tables near the appliance.
• DO NOT install the unit near combustible walls and materials. Failure to maintain safe distance may result in fire.
• When cleaning the appliance:
DO NOT steam clean.
DO NOT use products containing chlorine, or corrosive chemicals.
DO NOT use abrasive products, steel wool or scouring pads.
DO NOT use oven cleaners.
• DO NOT alter, add attachments, or otherwise modify this equipment!
• Failure to comply with CAUTION notices may result in damage to equipment or property, and void the factory
warranty.
NOTE:
• Users must comply with all appropriate state and/or local heath regulations regarding food service operations, and
cleaning/sanitization of food service equipment.
• NEVER attempt to clean and reuse a charcoal filter in the hood.
• Appliance and plenum discharge nozzles of the fire suppression system have been factoryinstalled and positioned in
the proper alignment. DO NOT MOVE OR ADJUST, except on recommendation of a certified fire protection
specialist.
• The decibel level of the hood when in operation is approximately 65 dB.
ix
x
Introduction GBF−50−VH Electric Fryer
1. Introduction
THANK YOU for purchasing the Giles Model GBF‐50‐VH Electric Fryer w/Integral Recirculating Hood, manufactured
by Giles Enterprises, Inc., Montgomery, Alabama (USA), hereafter referred to as "Giles". Every unit is thoroughly
inspected and tested prior to shipment in an effort to ensure that it will operate flawlessly when installed. With
proper care and maintenance this appliance should provide years of troublefree service.
To help protect your investment, we recommend that you take a few moments to become familiar with all of the
recommended procedures presented in this manual, pertaining to installation, operation, cleaning, and
maintenance of the appliance. Adhering to these procedures will help minimize the potential for costly downtime
and future repair expense. Please retain this manual for future reference.
NOTE: Due to continuing improvements and product enhancements, some illustrations shown here might not exactly depict
the actual equipment.
1.01 Construction
18 to 20 gauge, Highquality series stainless steel sheet metal ... stainless Firebar heating elements.
1.02 Standard Features

Computer Controller: Accurately controls oil temperature and cooking time. Dual cook timers, programmable
presets for up to fifty (50) different menu items, continuously monitors fryer operation, displays status, operating
instructions and warnings (DRAIN OPEN, LOW OIL LEVEL, MAX. ELEMENT TEMP, etc). Features BOIL OUT program,
COOL MODE function w/AUTO‐COOL option, FORCE FILTER control, LOW OIL detection, multiple language
selections, and password security option.
On‐board Oil Filtration System: Fully selfcontained oil filtering system. When used properly, can help extend the
useful life of cooking oil. Robust 1/2 hp pump ... designed to perform a filter cycle within approximately five (5)
minutes.
Steel Mesh Filter Screen: Has a sustainable, 115 micron retention, stainless steel filter screen instead of using
disposable paper filter media ... eliminates waste and helps reduce total cost of operation.
Ventless Hood: Integral, selfcontained, Type‐1 recirculating hood, 3stage air filtering ... electrostatic air cleaner
removes greaseladen cooking vapors and returns cleaned air into the room ... eliminates need for a conventional
ventilation hood, ducted outside.
Listed to UL KNKG, complies with ANSI/UL‐197 & ANSI/UL‐710B.
Fire Extinguishing System: Selfcontained, Ansul® R‐102 Wet Chemical Fire Suppression System protects against
accidental oil fire. Field set‐up and commisioning by an anauthorized Ansul® dealer/distributor is required, at
customer’s expense.
PUSH‐TO‐START power complies with certain code requirements (primarily in CA) which specify that appliance will
not automatically restart after a power interruption until attended by an operator.
1.02.1 Optional Features

Automatic Basket Lifts: Two (2) basket lifts ... automatically lower and raise cooking baskets at start and end of
cooking cycles ... can help avoid over cooked product.
KITCHENTRAC Monitoring: This WiFi connected feature provides fulltime monitoring of fryer activities and
operations via remote devices (laptop, tablet, smartphone). Keep track of loads cooked, idletime, filtering, sales
trends, equipment problem alerts, and many other analytics associated with cooking equipment utilization. Small
monthly server hosting fee is required.
1
GBF−50−VH Electric Fryer Introduction
1.03 Specifications
1.03.1 Overall Dimensions
INCHES [mm]
1.03.2 Agency Certifications
1.03.3 Basket Specification

Description Length Width Height Volume
Standard (2 per vat) 131/4 [337] 61/2 [165] 6 [152] 424 cu.in [6,942 cc]
INCHES [mm]
2
Introduction GBF−50−VH Electric Fryer
1.03.4 Vat Size & Capacities
Cooking Oil Capacity
Product Capacity
Height (Bottom of vat to [FULL] mark
Length Width (per Basket)
(Top of Element )
(Inside) (Inside)
to “FULL” Level)
Lbs [kg] Gal [l] Fries Chicken*
2.5 lbs 6.0 lbs
161/4 [413] 1329/32 [353] 5 [127] 50 [22.7] 7.1 [26.9]
[1.13 kg] [2.72 kg]
INCHES [mm] * Mixed pieces, 31/3 lb bird.
1.03.5 Shipping Specifications (Crated)
Crated Size
Gross Weight Cube
Length Width Height
618 lbs (280.3 kg) 46” [1168 mm] 36” [914 mm] 92” [2337 mm] 88 cu.ft (2.5 cu.m)
NOTE: Gross weight approx ... may vary slightly
3
4
Installation GBF−50−VH Electric Fryer
2. Installation
The following sections explain procedures for properly installing and preparing the appliance for use. To help avoid
personal injury or damage to the equipment, please adhere to all recommended procedures.
IMPORTANT! All material & labor expenses incurred during installation are the sole responsibility of the customer.
Generally, it is advisable to engage the services of professional commercial kitchen equipment specialists, a licensed
electrician, and/or a qualified HVAC contractor to manage the specific details of installation. Please call Giles
Technical Support @ 800.554.4537, if assistance is required.
2.01 Appliance Location
DO NOT MODIFY, ADD ATTACHMENTS OR OTHERWISE ALTER THIS EQUIPMENT
1. The appliance and surrounding area must be kept free and clear of combustible materials ... 18” (46cm)
clearance required.
2. The appliance must be electrically grounded in accordance with local code, or in the absence of local code,
with the National Electrical Code, ANSI/NFPA 70.
3. Allow adequate space for proper operation and future service & maintenance.
4. Be sure that electrical circuits available in the intended location are adequate to power the appliance load.
5. Make sure the unit will be installed is in a stable position and will not move unintentionally. The unit has
locking brakes on front caster wheels ... be sure they remained locked. Some jurisdictions may require that
additional special anchoring be installed to prevent excessive movement.
6. IMPORTANT!!
Before installing a GILES cooking appliance w/integral ventless hood, ensure that, ①. all necessary
approvals have been obtained from local code authorities, and ②. the installation site complies with all
specific requirements and limitations outlined in the GFSE Recirculating / Ventless Hood Approval Letter
(HAL). The document is available for review & download at www.gfse.com on the homepage under the
SUPPORT tab ... on the VENTLESS SUPPORT DOCUMENTS page.
To ensure satisfactory performance of the integral hood, the site and installation MUST comply with all
minimum requirements pertaining to number of appliances, kitchen size, ceiling height, fresh outdoor air
makeup, room air exchange rate, supplemental exhaust ventilation, clearances, etc. as stipulated in the
Hood Approval Letter.
• Giles makes no representation as to the proper design or layout of any establishment in which ventless
appliances are to be used. Further, Giles does not perform site inspections prior to installation of any of
its units.
7. Other appliance location considerations: hood exhaust will be 510 to 680 CFM ... average temperature of
recirculated air, after four (4) hours continuous frying will be approx. 90°F (32°C) ... the hood’s sound level
will be approx. 65 dB, when running.
8. The appliance is to be installed, used and maintained in accordance with the Standard for Ventilation
Control, and Fire Protection of Commercial Cooking Operations, NFPA 96.
If there are questions concerning installation procedures, contact Giles Technical Support at 800.554.4537, or email
services@gfse.com.
5
GBF−50−VH Electric Fryer Installation
2.02 Unpacking
The appliance is shipped on a wooden pallet; secured with hightensile plastic strapping and enclosed by a wooden
framework. The entire unit is wrapped in machine applied stretchfilm.
• The appliance must remain in an upright position during the unpacking process.
• Exercise care when removing the wooden framework from around the unit.
• The appliance is very heavy. Use extreme care and appropriate handling equipment and/or sufficient
manpower when lifting or moving the equipment.
• Failure to comply with these CAUTION notices may result in minor or moderate injury, equipment or property
damage, and void the factory warranty.
IMPORTANT!
If crate exhibited evidence of damage or mishandling, immediately inspect unit and all accessory items and
report any damages to the freight carrier. Typically it is the purchaser’s responsibility to file and negotiate
freight damage claims.
1. Carefully cut and remove the plastic shipping wrap and strapping. Remove and set aside all auxiliary items
packed with the unit. Filter pan and fryer accessories (baskets, screens, fryer tools, etc) are typically packed
in the vat and inside the fryer cabinet. Set these items aside in a safe place.
2. Use appropriate tools and work practices to remove the wooden crating from around the unit.
3. Carefully remove the appliance from the shipping pallet. The unit is very heavy, weighing in excess of 500
lbs [227 kg]. Use great care when lifting/moving the unit to avoid damage, or personal injury. Use
appropriate handling equipment or sufficient manpower.
IMPORTANT! Be aware that the appliance is top‐heavy and can easily tip over while rolling, should a
caster wheel hit a hole, large bump, or debris in the floor.
IMPORTANT!
Giles shall not be liable for damage to the unit, personal injury, or property damage caused by improper use of
material handling equipment or poor work practices during installation. Material & labor expenses associated
with installation of this appliance are the sole responsibility of the purchaser, unless written and approved
arrangements have been made in advance.
2.03 Electrical Requirements
• Fryers must be properly grounded in accordance with local code, or in the absence of local code, with the
National Electrical Code, ANSI/NFPA 70. Improper grounding may result in electrical shock to users.
• Always consult a professional electrician, or other qualified technician, prior to installation to ensure that electrical
circuits are of sufficient rating for the appliance load.
• GBF‐50‐VH Fryers are manufactured for various voltage/Hz/phase as shown in Table 2.04. Check the serial/data
label inside the cabinet or attached to the rear panel to determine the proper required electrical service.
6
2.04 Electrical Specifications
Voltage Phase Hz Watts* Amps Circuit Breaker Required
1 60 10,400 50 60
208 3 60 10,400 29 35
3 60 18,300 51 60
1 60 10,400 43 50
240 3 60 10,400 25 30
3 60 18,300 44 50
* Includes blower
2.05 Electrical Connections
NOTE:
All electrical installation labor & materials (breakers, conduit, wire, etc.) shall be supplied by the customer.
Electrical installation must be performed by a licensed electrician, or qualified service technician, as per local
building codes.
Installation must comply with all code requirements. Giles shall not be responsible for code compliance in
regard to installation and use of this appliance.
1. As needed, install appropriate circuit breaker(s) in main electrical panel. See Section 2.04.1.
2. Optional: Giles recommends that a service disconnect switch be installed between the main panel and the
appliance, such that all power may be easily removed from the unit when necessary.
3. See Section 2.05.1. Route 11/4” flexible conduit from panel (or disconnect switch) to the appliance and attach
it to the rear of the Service Entrance Box with appropriate fittings. Allow enough conduit length so that
appliance may be easily moved for cleaning and servicing.
4. See Figure 2.05.1. Open cabinet door and remove Service Box Cover.
5. Connect ground wire between the copper ground lug and a proper earth ground.
6. Pull appropriately sized wires from the panel (or disconnect switch) through to the service entrance box.
7. See Figure 2.05.1. Connect power supply wires to the distribution block located inside the service box and
reinstall cover.
7
2.05.1 Electrical Connection Diagram
Main Breaker Service Disconnect Incoming power

Box Switch supply conduit from
(Recommended)
rear of unit.
Service Box
Flexible Conduit
Ground Lug
Distribution Block:
connect supply power
to this side.
2.06 Ventless Hood Clearance
GBF‐50‐VH Fryer is equipped with an exhaust air diverter atop the hood which directs exhaust air horizontally to
the rear & side. The minimum clearance from top of the diverter to ceiling is 0” [0 mm], however it is
recommended that adequate space be provided to allow easy movement of the unit, if needed.
To allow proper airflow, the area at the sides and rear of the diverter must be kept free of obstructions.
DO NOT attach any type of additional ductwork to the unit in an attempt to divert hood exhaust out of the area.
Doing so will cause back‐pressure that can significantly reduce hood capture and result in unsatisfactory
performance.
8
2.07 Ventless Hood Fire Suppression System
The fire suppression system in the integral ventless hood is a selfcontained Ansul® R‐102 Wet Chemical Fire
Suppression System (UL197 Listed), designed and approved for providing fire protection for cooking appliances. It
is a mechanically activated system, automatically providing continuous protection. The system includes piping,
discharge nozzles (appliance/plenum), detector link brackets, cable conduit, Automan release mechanism, fire
damper, 1.5gal tank and a builtin manual activation station.
After appliance installation, final commissioning of the system must be performed by an authorized ANSUL®
agent in accordance with the appliance listing and shall include filling with wet chemical suppressant, installing
fusible detector links & cable, installing compressed gas firing cartridge, testing, certifying and arming. Most
jurisdictions will require installation of an additional remotely located manual activation station.
The fryer WILL NOT heat until the fire system is armed.
Cost of field setup is NOT included with purchase and is the customer’s responsibility.
2.08 Fusible Link Detector & Gas Cartridge Locations
9
2.09 Fire Extinguisher Nozzle & Tank Locations
All extinguisher system discharge nozzles have been factoryinstalled and aligned in the proper position. DO NOT
MOVE OR ADJUST, except on advice of a fire protection specialist.
All Nozzles = Ansul 1/2N
NOTE:
Tank is not factory‐
installed. Packed in
separate box (DO NOT
LOSE) ... must be filled and
installed by Ansul
technician when system is
commissioned.
10
2.10 Fire Alarm Connection
Connects the fire suppression system in the appliance to an existing facility fire alarm system, to send a control
signal to the alarm when the fire suppression system has been activated.
Fire Alarm Connection:

1. With hood rear panel removed, remove hole plug from hood top and install appropriately sized conduit and
necessary fittings. Route conduit to and attach at facility fire alarm system. Allow enough length such that
the appliance can be moved for access when cleaning and servicing.
2. Pull proper size wire and make appropriate connections.
Materials to be provided by customer.
11
2.11 Finalizing Installation
Every effort is made to ensure that new GILES fryers are in perfect operating condition when received ... each one has
passed rigorous quality control testing prior to shipment. To ensure that it has been properly installed and will operate
as expected when placed into service, we recommend that, after installation is complete, the following steps be
performed to check the unit’s basic functionality and to prepare the appliance for first use.
Before proceeding, please refer to Section 3 and become familiar with the various controls, systems and
functions. After reading and fully understanding this information, perform the following steps precisely to avoid
possibly damaging the equipment.
BEFORE BEGINNING:
• As needed, remove baskets, basket support screen and filter pan from the fryer.
• On the control panel, set ALL installed switches in the [OFF] position ... POWER, HEAT, PUMP & LIFT (if
installed).
• Confirm that drain valve is [CLOSED].
• IMPORTANT! Be sure that all hood filters are properly installed, and that the filter access cover is in place and
latched. Fryer will not powerup if the cover is missing or ajar. Missing or improperly aligned filters will also
cause errors/alarms, which may prevent some systems from operating.
• If any ot the following tests fail to produce indicated results, consult Section 6, Troubleshooting, or contact GILES
Technical Service at 800.554.4537 for assistance.
2.11.1 Power Test

The following test confirms that the unit is properly receiving power.
1. Confirm that circuit breakers supplying power to unit are ON.
If a disconnect switch is installed between the main panel and
fryer, be sure that it is in the ON position.
2. Place POWER switch in the [ON] position. The green POWER
light will illuminate and the hood fan should start running.
After the controller powers up, an alarm will sound ... press
the [ALARM] key to silence, leave power ON. and proceed
to Section 2.09.2.
If ...
ALARM POWER • POWER light does not turn ON.
• Controller does not powerup.
• Hood fan does not start running.
• Alarm sounds and an error is displayed on controller.
Refer to Section 6.01, Troubleshooting Procedures, else
proceed to Section 2.09.2.
12
2.11.2 Heat Test
This test confirms that heating elements are powered and properly energized by the controller.
Heating elements become extremely hot when energized! Bare skin contact will result in
severe burn injury.
2 1
1. Confirm that HEAT switch ① is in the [OFF] position and
drain valve inside lower cabinet
is completely closed.
2. Liberally dampen heating

elements with a wet sponge,
3
leaving visible moisture.
3. After performing Power Test,

controller displays ② should
read: upper ... [POWER FAILURE 4
PRESS [START] TO PREHEAT] and
lower ... [HOLD]. Press the [START] key ③.
4. The temperature setpoint and the notification [PREHEAT] should appear on the upper display screen ... red
HEAT indicator beside the lower display screen will turn ON and the realtime temperature is displayed. The
amber HEAT light ④ on control panel should NOT turn ON at this time.
5. Place HEAT switch ① in the [HEAT] position. The HEAT light ④ should now turn ON. Leave switch ON NO
MORE THAN 15 SECONDS, then return to the [OFF] position.
6. The moisture remianing on elements should quickly dry and heat should be felt rising from the vat.
DO NOT TOUCH HEATING ELEMENTS!
If ...
• Moisture does not dry quickly from the elements.
• No heating is detected.
Refer to Section 6.01, Troubleshooting Procedures, else proceed to Section 2.09.3.
NOTE: When performing this test, should the amber HEAT light turn OFF, alarm sound and the upper display
show the message “ERROR ‐ MAX ELEMENT TEMP”, the elements have energized properly ... return HEAT switch
to [OFF] and proceed to Section 2.09.3. Elements will need to cool down to clear this error ... follow controller
instructions displayed on the upper screen.
13
2.11.3 Filter Pump Test
The following test confirms that the filter pump is operating correctly. 2
1. If necessary, disconnect and remove the filter pan from unit.
2. Place the pump diverter valve handle ② in the [OIL RETURN] position (horizontal).
3. Firmly press the palm of your hand over the filter pan connection fitting ①. While
covering the opening, place the PUMP switch ③ in the [PUMP] position. With
pump running, if you feel suction on your hand, pump is operating properly.
Return switch to [OFF]. Allow pump to ONLY run long enough to check for 1
suction.
If ...
• Pump motor does not start.
• Motor starts, then stops abruptly ... overload trips.
• Suction is not felt.
• Air is blowing outward at coupling.
Refer to Section 6.01, Troubleshooting Procedures, else
proceed to Section 2.09.4.
2.11.4 Initial Fryer Cleaning

IMPORTANT!
Before using the appliance for the first time, perform the steps below and the Boil‐Out Procedure to remove residue
which may remain from manufacturing processes, or dirt and debris that may have accumulated during warehousing
and shipment. Explanation of the Boil‐Out Procedure is found in Section 4.02.
• Disassemble and thoroughly clean all parts of the filter pan. Rinse thoroughly, drain all water from pan’s plumbing
and dry completely. See Section 4.03, Cleaning the Filter Pan & Refreshing Filter Media for details.
• Wash all of the accessory items ... cooking baskets, basket carriers, screens, utensils, tools, etc. in warm soapy water,
rinse and allow to dry completely.
• Inspect unit for adhesive plastic protective film which may remain on sheet metal surfaces. Some of this material is
typically left in place to protect surfaces during storage and shipment. Remove all such material and clean the entire
exterior of the unit with a good quality stainless steel cleaner/polish. DO NOT use cleaners that are abrasive or
contain caustic chemicals.
14
2.11.5 Optional KITCHENTRAC™ Remote Equipment Monitoring
This section pertains ONLY to new equipment with factoryinstalled optional Giles’
KITCHENTRAC™ remote monitoring feature ...
Before the feature can be used, the account must be established and an open connection to
the internet must be available. A small monthly server hosting fee, per monitored
controller, will be required to use the service.
A wireless router, located within range of the appliance and having a continuous connection to the internet is
required. After the account has been activated, the fryer controller must be paired to the establishment’s WiFi
network, which is then connected with the KITCHENTRAC™ server.
A detailed WiFi Connection Manual (Form #66313) should have been packed with the unit, if equipped with the
WiFi feature. Before the monitoring service will become active, the steps outlined in those instructions must be
successfully completed. Appendix A in the back of this manual also explains the connection process.
Once connection is complete, you will be able to monitor appliance performance, productivity, operational status,
and many other analytics by loggingin to the KitchenTrac™ website from any computer or remote device (smart
phone, laptop, or tablet).
For additional monthly fees (per controller), Giles can offer “extended hours”, online monitoring of connected
equipment by a Giles’ Technical Support Associate, who will provide realtime notification of detected issues directly
to your designated operating personnel.
The appliance should now be ready for use, but before using it for the first time, please carefully read the
remainder of this Manual to become familiar with all of the controls, functions, operational steps and necessary
maintenance procedures ... see Fryer Operation, Section 4.
15
16
Overview GBF−50−VH Electric Fryer
3. Overview
The following section gives a brief overview of components, functions, and accessories for the GBF‐50‐VH Ventless
Fryer. Please review carefully before proceeding.
Integral
Ventless Hood
System
14” Cooking Vat

50lb Shortening Cap.
AutoBasket Lifts
(Optional)
Computer
Controller
OnBoard
Filtration
System
Lower Cabinet
17
GBF−50−VH Electric Fryer Overview
3.01 Baskets & Basket Lifts
2*
* Hidden
18
3.01 Baskets & Basket Lifts
Item Description Function

Optional Feature: Carrier arms hold the cook baskets in proper
(2) Basket Lifts w/Removable position. Lift automatically lowers basket into hot oil when a cook
1 Basket Carrier Arms cycle starts and raises it when cooking is complete.
(Optional)
A basket hanger rack on back header is standard.
When lifts are not installed, provides support surface for baskets
above the heating elements.
Basket Support/
2* Serves to help prevent crumbs & cooking debris from accumulating
Crumb Screen
around heating elements, which can affect performance & food
quality. Convenient handles for lifting out to clean.
Contains product for cooking. Plated wire baskets, 131/4” x 61/2”

3 (2) Baskets x 6” deep ... two (2) provided with each unit.
*Additonal baskets may be purchased separately*
Always wear thermal protection, such as mitts or gloves, when handling these parts
during normal operation ... they can beome very hot!
* Hidden
19
3.02 Control Panel
3.1 3 3.2 2
7 6 10 1 5 8
20
3.02 Control Panel
Main power switch for turning unit ON/OFF. Place in [ON] to powerup the
1 POWER Switch
controller and start the hood fan.
Heating elements are only active when this switch is in the [HEAT] position.
2 HEAT Switch
When switch is in [OFF] position, fryer heat is disabled.
Monitors & controls oil temperature, cook time and other fryer functions.
Dual cooking timers, programmable cooking presets for up to fifty (50)
3 Computer Controller different menu items. The upper screen shows cook settings, error
messages & alarms, operating information/instructions, etc. The lower
screen shows temp/time values & other information.
3.1 Function Keys Pressing these keys activate various controller functions.
Use to input values (menu #, time, temp, etc) & start/clear actions. The [2]
3.2 Controller Keypad [4] [6] [8] keys are directional keys in certain situations for scrolling,
making selections and other functions.
● Green POWER turns on when POWER switch is in the [ON] position.
● Amber HEAT turns on while heating elements are energized by the
Indicator Lights: controller when HEAT switch is in the [HEAT] position. Light cycles
ON/OFF during normal operation as controller maintains oil
● Green
5 temperature.
● Amber
● Red ● Red HILIMIT ON indicates elements have shutdown due to an over
heat condition. If light turns ON during operation, DISCONTINUE
COOKING and refer to Troubleshooting, Section 6. DO NOT COOK
UNTIL THE CAUSE OF HI‐LIMIT SHUTDOWN IS DETERMINED!
● [ON] light turns ON when electronic air cleaner (EAC) is powered and
the system is operating ... the only light illuminated when system is
operating properly.
E.A.C. Status Lights:
● [WASH] / [CHECK] LED indicators turn on to notify of various alarm
● ON
6 conditions in the air cleaning system (see Section 6.02 for more info).
● WASH
If the [WASH] light turns ON, power to heating elements will shutdown
● CHECK
after approx. 2 minutes. DO NOT USE this light as a signal for routine
cleaning ... to maintain peak performance, the collector cell must be
cleaned DAILY (whether the [WASH] light is on or not).
Controls the filter pump for filtering oil or pumping waste oil from the
7 PUMP Switch
fryer for disposal.
LIFT Switch Place in the [LIFT] position to enable basket lifts, when installed. The lift
8 (Optional, only when basket lifts are lowers basket when cycle starts and raises it when cooking is done.
installed) Placing in [OFF] position disables both lifts.
Fire Extinguisher Pull this handle to manually activate the fire suppression system before a
9
Manual Pull Handle fire has become large enough to automatically trip the system.
● CHANGE SOON light turns ON when timer enters WARNING mode ...
notifies that collector cell must be cleaned within 24 hours.
E.A.C. Cleaning Timer ● CHANGE NOW light turns ON to notify that timer has TIMED OUT. An
● CHANGE SOON (Yellow) alarm sounds and fryer will be disabled until collector cell is cleaned (or
10 ● CHANGE NOW (Red) exchanged with a clean cell).
● SNOOZE SNOOZE Button press the button after TIME OUT occurs to return to
WARNING mode, which allows continued operation for 2 hours.
SNOOZE can be used twice, then fryer will be locked‐out until EAC
cleaning or exchange is performed.
21
3.03 Lower Cabinet
3
1
22
3.03 Lower Cabinet
Opens/closes the vat drain valve. Prior to adding cooking oil (or
water for boilout) always be sure the valve is fully CLOSED (handle
in leftmost position to stop). Fryer will not heat if valve is not
completely closed & interlock switch is not properly engaged!
1 Drain Valve Handle Even though safety interlocks are designed

into the unit, always be sure the HEAT Switch
on control panel is in the [OFF] position before opening this valve.
Failure to do so could result in fire, causing serious injury (even
death), damage to equipment or property, and void the warranty.
Directs discharge of filter pump to either, return oil from filter pan
Pump Diverter Valve
2 to fryer vat or send it to a handheld waste oil discharge hose
Handle
connected at the discharge hose coupling.
Oil Discharge Hose Quickcoupler fitting for attaching the handheld oil discharge hose
3
Connection to the fryer filter system for removing waste cooking oil.
Quickcoupler fitting for connecting the filter pan assembly to the

4 Filter Pan Connection
fryer filter system.
Collects and contains cooking oil when drained from vat. Filter
5 Filter Pan Assembly media inside pan filters and reconditions used cooking oil during
a filter cycle (see Section 3.04, Filter Pan Assembly for more info).
23
3.04 Filter Pan Assembly
5
Hold‐down Frame
locking levers in Pan
bottom.
4
24
3.04 Filter Pan Assembly
To avoid potential oil spillage or burn hazards, never remove the filter pan while it contains
hot liquid shortening. Please see Section 4.04, Removal of Liquid Shortening.
• While attending the fryer, always wear thermal protection, such as gloves or oven mitts, when handling the
filter pan and its parts ... they can become very HOT during normal operation!
• Never drain boilout solution into the filter pan. It can be corrosive and will damage the filter pan and/or filter
pump. See Section 5.01, Boil‐Out Procedure.
Secures the filter media tightly against filter pan bottom to create a
1 HoldDown Frame
proper suction seal for the filter pump.
Stainless steel mesh filter screen media (115 micron) removes fine
Stainless Steel Filter Screen particles of cooking residue from used cooking oil. Washable and
2
(Standard) sustainable ... can reduce operating cost and eliminates part of the
kitchen waste stream.
Filter paper media may be used instead of the screen ... only one (1)
Filter Paper
3 sheet is required. IMPORTANT! Never use filter paper and the
(Optional)
screen at the same time.
Collects oil that is drained from vat. Pan assembly has with casters
and is easily rolled out for cleaning. A perforated screen is
permanently affixed to the pan bottom as a filter media support.
THIS IS NOT THE FILTER ... FILTER MEDIA MUST BE USED! DO NOT
4 Filter Pan
ATTEMPT TO REMOVE THIS SUPPORT SCREEN.
As a Best Practice for maintaining good operation and optimum
food quality, Giles recommends that cooking oil be filtered after
every 4th batch cooked, at a minimum.
Connects the pan assembly to the fryer filtration system. Hose must
5 Filter Pan Hose & Fitting
be disconnected before filter pan can be removed from fryer.
Lays atop of the filter pan and aids in minimizing splash and splatter
as oil is being drained from vat. Helps to keep cabinet interior and
6 Filter Pan Cover
floor beneath fryer clean, as well as helping to prevent oil
contamination.
25
3.05 Ventless Hood
2 7
3
5
6
26
3.05 Ventless Hood
Covers the filter chamber and hood plenum ... remove to access baffle
1 Filter Access Cover filter, E.A.C. collector cell & charcoal filter. This cover must be in place
and properly latched before the appliance will operate.
Helps control cooking odors in the exhausted air. This filter is a
consumable item and typically replaced monthly. NEVER attempt to clean
2 Charcoal Filter ... it CANNOT be reused. It is advisable to keep a spare filter on hand for
quick exchange when needed! NOTE: No filter will effectively remove ALL
cooking aroma.
Electrostatic Air Cleaner removes grease vapor and
smoke generated while cooking. The cell is
completely renewable and should be cleaned daily
3 E.A.C. Collector Cell
to maintain peak performance. Appliance power
must be turned OFF before removing cell for
cleaning.
First stage of the air cleaning system ... removes
larger grease particulate. It is easily removed for
4 Baffle Filter daily cleaning. DO NOT attempt to operate the
appliance with this filter removed. Doing so will
expose the energized EAC cell, which can present
an electrical shock hazard.
Collects grease condensate generated by the baffle filter. Inspect daily

5 Grease Drip Cup
and clean as needed.
Grease Drip Cup Safety Secures the drip cup, preventing it from unintentionally falling from the
6
Pin holding bracket.
The hood top serves as an air diverter to direct exhaust air horizontally
Hood Top/ to the sides and rear. Allows for 0” clearance requirement between the
7
Exhaust Diverter ceiling and top of the hood. However, it is advisable to have some
clearance to allow for ease of moving the appliance, if needed.
27
3.06 Accessories Provided
Part Description/Part No. Function
Kettle Drain Brush Use to clean the vat drain and other
P/N: 71025 parts.
L Shaped Brush Use to clean between, around and

P/N: 93609 beneath heating elements.
Heatresistant, multipurpose, use to

Heatresistant Cleaning Brush
clean vat sides, bottom and heating
P/N: 71100
elements.
Crumb Shovel Use to remove sediment from the

P/N: 30059 Filter Pan after filter cycle.
28
3.06 Accessories Provided
Use to discharge waste cooking oil to

a disposal container when removing
Oil Discharge Hose from the fryer.
P/N: 33667
Note: Not intended for washing
down vat!
Basket
Contains product for cooking. Vat
131/4”x 61/2”x 6”
accommodates (2) Baskets.
P/N: 41040
Supports baskets while cooking

Basket Support/Fry Screen without using basket lifts.
P/N: 41041 Prevents excessive crumbs or residue
from accumulating around heating
elements.
Sustainable stainless steel filter

Stainless Filter Screen media for the filter pan. Filters used
P/N: 41078 cooking oil as it is circulated through
filtering system.
29
3.07 Accessories Not Provided

A portable oil disposal container with

capacity to hold 80 lbs. of
Giles Oil Caddy liquid waste shortening.
P/N: 79187
Note: For use with filtered, warm oil
only (no crumbs or debris).
Paper filter media for use in the filter

pan to clean cooking oil when it is
Filter Paper circulated through Filtration System.
P/N: 65871
Use instead of reusable stainless steel
filter screen.
Filter Powder
Filtering aid used during the oil filtration
P/N: 72004
process. Helps recondition cooking oil
Portion Packs
by removing soluble impurities.
60 Ct.
30
3.07 Accessories Not Provided
Fryer BoilOut
P/N: 72003
Add to water in the vat to make up
(4) 8lb Jugs
boilout solution for cleaning and
degreasing vat.
P/N: 720031
Single 8lb Jug
Fry Pot Cover Covers fry pot during periods of

P/N 93362 inactivity, protecting against
(Purchased separately) contamination of cooking oil.
31
32
Fryer Operation GBF−50−VH Electric Fryer
4. Fryer Operation
The GBF‐50‐VH Electric Fryer is a multipurpose fryer equipped with an integral ventless recirculating hood. It has a
dualtimer computer cooking controller, onboard oil filtering system, and capacity for 50 lbs. of liquid frying
shortening.
• Turn off fryer power switch and supply power circuit breaker in the appropriate electrical panel before cleaning
or performing maintenance on the appliance.
• DO NOT wash down the appliance with water spray, or any pressuretype washing equipment. The control
panel is “liquid resistant”, but is NOT “wash‐down safe”.
• Failure to comply with DANGER notices will result in serious injury, even death, damage to equipment or
property and void the factory warranty
• DO NOT use or store flammable liquids, or materials that produce flammable vapors, in the vicinity of this or
any other appliance!
• DO NOT for any reason, nor ALLOW OTHERS to, stand or step onto the top of the fryer. Very
serious injury can result from slips and falls, or from bodily contact with extremely HOT cooking oil
in the vat (higher than 330°F/166°C). The removable covers often placed over cooking vats are
NOT designed to, and WILL NOT, support the weight of a person.
• Failure to comply with WARNING notices could result in serious injury, even death; damage to equipment
and/or property and will void the factory warranty.
• Be sure the fryer is positioned in a stable, safe location with front caster brakes locked. An appliance restraint
cable may be required by local building codes ... consult your local code authority.
• Exercise caution when operating and cleaning. To avoid personal injury, wear thermal protection (gloves or
mitts) while tending the appliance. Certain parts of fryer become very HOT during operation; temperatures
inside the cabinet may exceed 150°F/65.5°C and typically, cooking oil temperature will be in excess of
330°F/166°C.
• This appliance is intended for commercial use and is to only be operated by qualified personnel. It is not
intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or those
lacking experience and knowledge, unless they have been given adequate instruction and/or supervision
concerning its operation by a person responsible for their safety.
33
GBF−50−VH Electric Fryer Fryer Operation
4.01 Computer Controller
The following subsections explain use of the Dual‐Timer Computer Cooking Controller ... features, functions,
programming, and operational procedures.
4.01.1 Keys and Functions
Numeric Keypad: Use to enter cook setting values and to edit controller various
settings. The [2, 4, 6 & 8] keys are used as [ARROW KEYS] to operate optional basket
lifts when installed, making selections, navigating lists and moving the cursor. [2 & 8]
= UP/DOWN ... [4 & 6] = LEFT/RIGHT. The keys will illuminate when they are active as
directional keys.
[START]: A function key used to select & start functions, save settings, etc.
[CLEAR]: A function key used to cancel processes, exit functions, etc.
Continued on Next Page

34
4.01.1 Keys and Functions − continued
MENU key: Action key which is pressed in combination with other keys to access programmed
cooking presets. Cooking presets can be programmed for up to 50 different menu items.
EDIT key: Action key which is pressed in combination with other keys to enter edit mode for
changing or entering new menu item cooking presets.
TEMP key: Press to begin entering a cooking temperature setpoint. When fryer is in READY state,
press the key twice (2x) to display the realtime actual oil temperature on the lower display screen
for approximately 20 secs. NOTE: While controller is in PREHEAT mode, realtime actual
temperature is already displayed.
CLOCK key: Press to begin setting the cooking time (mm:ss) manually.
While fryer is in PREHEAT mode, press key to start the BOIL‐OUT program. Temp setpoint and
time will change to the BOIL TEMP and BOIL OUT TIME settings specified in User Settings (Section
4.01.8). Default = 200°F & 30 mins.
Press key to place fryer into COOL mode. When activated, the feature lowers temperature
setpoint during idle periods to save energy. The COOL TEMP setting is specified in User Settings
(Section 4.01.8). Default = 275°F.
ALARM reset key: Press to silence the controller alarm and acknowledge certain status messages.
BASKET key: Activates [2] UP & [8] DOWN keys for use to manually operate optional basket lifts.
Key is disabled while fryer is in PREHEAT mode to prevent product from being lowered into oil that
is not yet at proper temperature. Key is inactive when optional basket lifts are not installed.
Upper Display Screen (blue graphic): Displays status information, setting

values, operational instructions, alarm/error messages, etc.
Lower Display Screen (red graphic): Displays various status information,

timer countdown, temperature, error codes, etc.
[HEAT] indicator turns on when controller output is signaling to energize
heating elements.
[LEFT/RIGHT Timer] indicators illuminate to show which timer countdown is
being shown on the display screen.
35
4.01.2 General Controller Operation
The following is general operational information only ... detailed procedures and instructions are covered in
subsequent sections. While operating the fryer, instructions and prompts are shown on the upper display to help
guide you the through various processes and functions. Certain controller keys and indicator lights will illuminate as
a further guide.
● POWER UP:
Place POWER switch in [ON] position. Controller boots up, alarm sounds and the message “POWER FAILURE
[PRESS START TO PREHEAT]” is shown on the upper display screen. This is normal ... it as a precaution to
prevent fryer from starting to heat without an operator present. Pressing the [START] key silences alarm and
places fryer into PREHEAT mode. If the HEAT switch is in the [HEAT] position and the temperature setpoint is
higher than the current oil temperature, heating elements will turn ON and fryer will begin heating.
CAUTION! DO NOT place HEAT switch in [HEAT] position unless vat is filled to the FULL level with
cooking oil (or water).
● PREHEAT:
During PREHEAT cycle, realtime oil temperature is displayed on the lower display screen. When oil reaches the
programmed setpoint, alarm sounds, upper display screen shows the message “ALARM ‐ STIR OIL”. Press the
[ALARM] key and use an appropriate utensil, such as the provided stirring utensil, to vigorously stir the oil.
Typically, oil temp drops when stirred, so controller holds for 10 seconds and if temperature drops below
setpoint during this time, PREHEAT continues until it is reached again. This process helps to ensure more
consistent temperature throughout the total volume of oil, leading to better cooking performance. Upon
reaching setpoint again, alarm sounds and upper display shows “ALARM ‐ SETPOINT REACHED”. Press the
[ALARM] key to place fryer into READY state.
● READY STATE:
Fryer is ready for cooking. The lower display screen changes to show the current controller temperature setpoint
and the last used fryer cook settings are shown on the upper display screen.
While in PREHEAT or READY state, you can change cook setting by selecting a different menu preset, see Section
4.01.5.2, Selecting a Menu Preset OR you can manually input different settings (time and/or temp), see
Section 4.01.3, Setting the Cooking Temperature & Section 4.01.4, Manually Setting the Cook Time.
NOTE: If PASSCODE ENABLE parameter is set to ON, operator cannot manually set cook time without first
entering the proper password. This password feature provides a measure of control over cooking procedures.
‐
● START:
Each basket active cook time setting (presets or manual) is shown on the upper display screen. To start a
cooking cycle press the [START] key + select side; [4] = Left [5] = Both [6] = Right ... timer begins to countdown.
+ +
36
4.01.3 Setting the Cooking Temperature
Cooking temperature setpoints must be manually input ... the programmable menu item presets do not include
cooking temperatures.
Instructional prompts are shown on the upper display screen to guide you.
Press the
[TEMP] key
Use keypad to
enter cooking
temperature
setpoint (°F).
Ex: 325 = 325°F
Press the [START]

key to save the
entry.
• If actual oil temperature is lower than the entered setpoint, controller enters PREHEAT mode (small red HEAT
indicator beside lower screen on controller turns ON). However, heating elements will NOT actually turn ON until
the HEAT switch on control panel is placed in the [HEAT] position. At that time, amber HEAT indicator light on
control panel will turn ON and oil begins heating.
CAUTION! DO NOT place HEAT switch in [HEAT] position unless the cook vat is filled to the FULL level with
cooking oil (or water).
• If oil temperature is already equal to or greater than the entered setpoint, after 10 seconds an alarm sounds and
the message “SETPOINT REACHED” is displayed. Press the [ALARM] key and fryer enters READY state and is now
ready for cooking.
During PREHEAT, realtime actual oil temperature is shown on the lower display screen. When setpoint is reached,
the display will change to show the setpoint temperature.
NOTE:
Pressing the [TEMP] key two times (2x) will display actual oil temperature for about 20 seconds.
The default temperature unit is °F ... this can be changed to °C in User Settings, Section 4.01.8.
37
4.01.4 Manually Setting the Cook Time
You may wish to enter a cook time manually rather than use one of the programmed menu presets. The following
explains entering a cook time manually.
IMPORTANT! If PASSCODE ENABLE is set to ON in user settings, you cannot enter a cooking time unless you first
enter a password. You can still choose a preset from the programmed selections, see Section 4.01.5.
Press the
[CLOCK] key
Use keypad to enter a

cooking time (mm:ss).
Ex: 1530 = 15:30
NOTE: All the digits must
be entered.
Press the
[START] key.
Use keypad to select which side the

setting is to apply
[4]=Left [5]=Both [6]=Right
Unless BOTH is selected, you can repeat the process to set a different time for the
other basket.
NOTE: Menu presets include item names which will be displayed on the upper
display screen when selected. When cooking time is manually input the title
“MANUAL” is displayed instead of an menu item name to indicate a manually
entered time is being used.
38
4.01.5 Working with Menu Item Presets
NOTE:
Cooking presets stored in the controller do not include cooking temperature settings. Temp setting is always input
manually before cooking ... see Section 4.01.3.
Presets for up to fifty (50) different menu items can be programmed in the controller ... each includes:
● Menu No. Sequential ID number
● Menu Name Name of the food product assigned to the preset.
● Cook Time Cooking time for the item.
● STIR OVERRIDE Overrides the global setting for the STIR ALARM feature for the particular menu item. Factory
default = [NORMAL] = the feature functions according to the global user setting.
● FISH FILTER To help prevent flavor transfer, particularly for seafood, you may wish to filter oil after cooking only
one (1) batch of the item. This setting overrides the global setting for the FORCE FILTER feature. Factory default
= [OFF] = the feature functions according to global user setting. A SNOOZE feature is available which will allow
two (2) batches of the item to be cooked before forced filter occurs.
All 50 Menu Presets are factory preprogrammed with the default settings shown in the table below. Menus 1 ‐ 10
are set for some typical popular food items. Items 11 ‐ 50 contain general settings as shown on the last line of the
table. You can edit any of these presets to customize them to your specific menu and cooking operations.
MENU NO. MENU NAME TIME (MM:SS) STIR OVERRIDE FISH FILTER
1 BONEINCHICKEN 13:00 NORMAL OFF
2 TENDERS 7:00 NORMAL OFF
3 WEDGES 6:00 NORMAL OFF
4 BONEINWINGS 8:00 NORMAL OFF
5 BONELESS WINGS 7:00 NORMAL OFF
6 POPCORN CHICKEN 3:00 NORMAL OFF
7 LIVERS 4:00 NORMAL OFF
8 CORNDOGS 10:00 NORMAL OFF
9 CHEESE STICKS 3:00 NORMAL OFF
10 FISH 3:00 NORMAL OFF
11 thru 50 MENU XX 2:00 NORMAL OFF
The following sections explain the steps required to edit a Cooking Preset.
39
4.01.5.1 Editing a Menu Item Preset
Press the [MENU] key two Edit NAME: Two methods available
+ times (2x) Method 1
Enter NAME letter by letter
Choose NAME setting as

Use [2] Up & [8] Down keys to described at the left. A
scroll through items until the flashing cursor will appear at
Menu No. you want to edit is the first letter of the current
displayed. name. Use arrow keys [2 & 8] to
scroll thru alphabet ... the
character at cursor changes ...
stop on the desired letter. Press
right arrow key [6>] to move
cursor to next character in the
name ... repeat until entry is
Press the [EDIT] key (not START) to complete.
begin editing ... the current settings
for this item are displayed. When finished editing, press [START] to save
‐ OR ‐
Press [CLEAR] to Cancel & Exit without saving
Use left arrow key [<4] to backspace and erase errors.

Use [2] & [8] arrow keys to move the cursor [>] until
it points to the setting you wish to edit: Method 2
NAME Select a NAME from catalog of programmed names.
—>TIME
STIR OVERRIDE Choose NAME setting as
FISH FILTER described at the left. Cursor
To edit [NAME] or [TIME], press [START] key to select appears at first letter. Press
and begin editing. [0] key to open a catalog of
NOTE: When editing [STIR] or [FISH] setting, press programmed names ... use
[START] to toggle through the available settings & arrow keys [2 & 8] to scroll
stop on the desired selection to choose. through list. Stop at desired
name & press [START] to copy the
Pressing the [4] key backsup to a previous setting. selected name to the item being
Pressing the [6] key advances to the next setting. edited. The previous display returns.
When finished, press [START]

to save ‐ OR ‐ Press [CLEAR]
to Cancel & Exit without
saving ‐ OR ‐ Press [0] to reopen
the name catalog.

40
4.01.5.1 Editing a Menu Item Preset − continued
Edit COOKING TIME:
Scroll to and choose the TIME

setting as shown on previous page.
Current time setting for the item is displayed.

Use numeric keypad to enter a new TIME (mm:ss)
NOTE: All digits must be entered, e.g. 10:00 mins = 1000.
When entering time, [CLEAR] key backspaces to erase a errors.
After entering new TIME value, press [START] to save

OR
Press CLEAR to exit without saving
Edit STIR OVERRIDE Setting:
Regardless of the global STIR ALARM setting (Section 4.01.8), you may wish to have a particular product stirred or
not stirred during the cook cycle. This setting can override the global setting for a specific menu item. The settings
can be [NORMAL], [SKIP] or [FORCE].
[NORMAL] = stir alarm activates normally, according to the global user setting.
[SKIP] = controller WILL NOT issue the stir alarm for the menu item, regardless of global user setting.
[FORCE] = controller ALWAYS issues the stir alarm for the menu item, regardless of global user setting.
Factory default setting is [NORMAL]
To edit STIR OVERRIDE setting, scroll to and choose as described previously ... [—>] pointing to [STIR]
Pressing the [START] key toggles between the available options, stop on desired choice to select setting.

41
4.01.5.1 Editing a Menu Item Preset − continued
Edit FISH FILTER Setting:
To minimize potential for flavor transfer, establishments cooking seafoods may wish to have operators filter oil after
every batch cooked. When FISH FILTER is set to [ON], the fryer will enter FILTER MODE after cooking (1) load of
the menu item. If the FORCE FILTER SNOOZE user setting is set to [ON] (Section 4.01.8), two (2) batches can be
cooked before Forced Filter is activated or a filter prompt is displayed.
When FISH FILTER is set [ON], it is in effect regardless of whether the FORCE FILTER user setting is ON or OFF.
When setting is [OFF] only a message is shown on the upper controller screen prompting operator to filter oil ...
when setting is [ON] fryer will be locked out of continuing operation until filtering is performed.
To edit FISH FILTER setting, scroll to and choose as described previously ... [—>] points to [FISH FLTR]
Pressing the [START] key toggles between [ON] / [OFF] ... stop on choice to select setting.
Leaving EDIT Mode:

When editing the Menu Item Preset is complete, verify the entries and then press either the [CLEAR] or [EDIT] key,
to exit. Arrow keys [2] & [8] remain active and can be used to scroll to a different menu item for editing.
Press the [CLEAR] key again to completely exit EDIT Mode.
42
4.01.5.2 Selecting a Menu Item Preset for Cooking
A. Direct Entry Method Menu No. is known. B. Scroll Method Scroll through list of items.
Press the [MENU] key once

‐ OR ‐ Press the [MENU] key
Skip and enter the desired + two times (2x)
Menu No.
Enter desired Menu no. [150].
Use numeric keypad [2]

& [8] (up/down) to scroll
through list to the
desired item.
Press [START] key to select

the setting.
Use keypad to choose side

Press the [START] key to
select the setting.
Use keypad to choose side

NOTE:
• If the user setting “COOK ON MENU SELECT” is set [ON] and fryer is in READY state, it will automatically enter
COOK mode as soon as the basket side is selected; cooking time begins counting down on lower display screen.
If basket lifts are installed & active, the basket of selected side is lowered for to cooking. WHEN THIS SETTING IS
IN EFFECT, BE SURE THAT PRODUCT IS PROPERLY LOADED IN BASKET BEFORE SELECTING SIDE.
• If this setting is set [OFF] (default), the cooking cycle must be started as explained in Section 4.01.6.
43
4.01.6 Cooking Cycle General Overview
COOKING TEMPERATURE, ITEM NAMES, COOK TIMES, STIR OVERRIDE & FISH
FILTER settings are shown on the upper display screen. The READY notification
indicates that cooking oil is at proper temperature and fryer is ready for
cooking.
When in READY state, temperature setpoint is shown on lower display screen.
After selecting an item preset, or manually entering cooking time, start the cook
cycle by pressing the [START] key once.
You are then prompted to select basket side. Either or both sides can be
selected ... press appropriate number key to select.
When side is selected, controller enters COOK state ...
NOTE: Fryer will not enter COOK unless it is in READY state.
If fryer is equipped with optional automatic basket lifts and they are enabled,
appropriate basket(s) will be lowered into cooking oil and the programmed
cooking time will begin counting down, shown on the lower display screen. If
lifts are not installed (or turned OFF), manually place basket(s) into oil, resting
on support screen in bottom of vat.
The upper display screen indicates which side is cooking, and shows the
temperature setpoint. Timer Indicators beside the lower screen indicates which
timer is currently being displayed.
Two different menu items can be selected and started together as described in
Section 4.01.5.2 ... each item must require the same cooking temperature.
After selecting a second preset (or entering a different time), press the [START]
key once again and when prompted, press the appropriate arrow key (<4 or 6>)
to start the second timer (there is only one selection at this time). Lower display
and timer indicator will change to show the second timer countdown.
When both timers are active, pressing the [TIME] key 2 times will
x 2 toggle lower display screen between timers.
STIR ALARM: When setup and enabled in user settings (Section 4.08.1), the alarm and associated display prompts
are issued at the specified time during the cook cycle, notifying the operator to stir the cooking product. Stirring
can help promote more even cooking and prevent pieces from sticking. STIR ALARM % setting is the amount of
cook time to expire before alarm is activated ... e.g. [STIR ALARM %] = 60, then during a 10 min. cook cycle, the
alarm is activated after 6 mins. of cook time has elapsed.
Factory default setting is [STIR ALARM ENABLE] = ON & [STIR ALARM %] = 62.
A STIR OVERRIDE can be set for a menu preset to override the global user setting, see Section 4.01.5.1.
When cooking cycle time is complete, an alarm sounds and message “DONE COOKING ‐ (LEFT) (RIGHT) or (BOTH)”
is displayed, as appropriate. If fryer is equipped with basket lifts, basket is automatically raised. Press the [ALARM]
key to silence alarm. Fryer then returns to READY state, awaiting the next load of product.
Canceling a Running Cook Cycle:
Press the [CLEAR] key once, then press it again to cancel cooking
x2 ‐ OR ‐
Press [4] to continue cooking.
44
4.01.7 Additional Controller Features
4.01.7.1 Manually Operating Optional Basket Lifts (when installed)
Press the [BASKET] key once
Use keypad [2] UP [8] DOWN key to select

raise or lower.
Press [CLEAR] to cancel the operation.
Press appropriate key to select side

Selected lift(s) will operate as specified.
NOTE:
▪ LIFT switch on control panel must be in the [ON] position before lifts will operate.
▪ As a safeguard against placing product into oil that is not at cooking temperature, manual basket lift operation is
disabled while the controller is in PREHEAT state.
▪ Once a lift has been operated, it will NOT actuate again for approximately 20 seconds, or until the red indicator
above the BASKET key turns off.
4.01.7.2 COOL Mode
COOL Mode is an energysaving feature for use during periods of inactivity. When selected it
automatically changes the controller’s oil temperature setpoint to a lower value and places
fryer into an standby state.
Press the [COOL] key once to enter COOL mode. Temperature setpoint changes to the COOL
TEMP setting specified in user settings, see Section 4.01.8.
Factory default setting is 275°F ... available range is 200°F ‐ 350°F.
To exit COOL press the [CLEAR] key, then press [<4] to exit
OR
+ Press [CLEAR] again to continue COOL mode.
When exited, temperature setpoint returns to the previous active value and fryer
enters PREHEAT until the set temperature is reached. The STIR OIL alarm will be
issued when setpoint is reached, as described in Section 4.01.2.
45
4.01.7.3 AUTO−COOL Feature
If AUTO‐COOL feature is set to [ON], fryer will automatically enter COOL Mode when no cook cycles have been
started within the amount of time specified by the [AUTOCOOL TIME] setting in user settings (Section 4.01.8).
Factory default setting is [AUTOCOOL] = OFF & [AUTOCOOL TIME] = 30 ... available time range is 1 ‐ 510 mins.
Exit AUTO‐COOL same as COOL mode ... press the [CLEAR] key, then press [<4] to exit
OR
Press [CLEAR] again to continue COOL mode.
+
When exited, temperature setpoint returns to the previous active value and fryer
enters PREHEAT until the set temperature is reached. The STIR OIL alarm will be
issued when setpoint is reached, as described in Section 4.01.2.
4.01.7.4 BOIL OUT Mode

After fryer has been properly prepared for a boilout process (Section 5.02), and while
controller is in PREHEAT mode, press the [BOIL] key to enter BOIL OUT Mode.
Temperature setpoint and time setting change to the BOIL TEMP and BOIL OUT TIME
settings, respectively, as specified in user settings (Section 4.01.8). The boil out solution
will continue heating to boil temp & boil out time countdown is shown in lower display
screen.
Factory defaults settings are:
BOIL TEMP = 200°F ... available temp range is 185° ‐ 208°F.
BOIL OUT TIME = 30 minutes ... available time range is 1 ‐ 45 mins.
IMPORTANT!
After BOIL OUT program is complete, the controller automatically resets the temperature setpoint to 50°F. It
must be reset to a proper cooking temperature before the fryer will heat cooking oil for normal operation.
Fryer must be properly drained, rinsed and prepared for cooking after performing a boil out procedure. See
Section 5.02, Boil‐Out Procedure for complete details.
46
4.01.8 User Settings
To access the User Press Enter on Press
Settings menu and edit [TIME] key keypad [START] key
The table below details available User
settings ...
Settings and factory set Defaults.
+ 9999 +
Keypad [4] & [6] (left/right) will scroll through the available settings ... current setting values are shown on the
upper controller display.
NOTE:
• Press the [EDIT] key, when setting is displayed to begin edit.
• Use keys [2] & [8] (up/down) to change the setting value. The message “TOO LOW” or “TOO
Press [EDIT] key again to SAVE. HIGH” is displayed if an entered value is
outside of the allowable range and will
To exit User Settings menu, press the [CLEAR] key. cause a controller error.
NAME DESCRIPTION RANGE DEFAULT

TEMP SCALE Temperature unit of measure °F or °C °F
If ON, forces operator to filter oil after completing the number
FORCE FILTER of cook cycles specified by FILTER COUNT ... fryer will be ON OFF ON
disabled from continued use until oil is filtered.
FORCE FILTER If ON, allows (1) additional cook cycle after FILTER COUNT is
ON OFF OFF
SNOOZE exceeded ... active only when FORCE FILTER is ON.
FILTER COUNT Number of cook cycles before filtering is required. 1 to 20 4
Cooking not allowed if oil temperature is outside of the
GUARD BAND 1 to 990 900
setpoint by guard band amount.
MAX SETPOINT Maximum oil temp setpoint allowed by controller. 32°F to 375°F 350°
Automatically places fryer into energysaving COOL mode after
AUTOCOOL ON OFF OFF
a specified amount of idle time.
AUTOCOOL TIME When AUTOCOOL is ON, if no cook cycles have been started
1 to 510 minutes 30
(MINUTES) within this time, fryer automatically enters COOL mode.
AUDIBLE ALARM Duration of the audible alarm in seconds ... alarms
5 to 120 seconds 10
(SECONDS) automatically silence after this time.
COOL TEMP Temperature setting for COOL mode 200°F to 350°F 275°F
BOIL TEMP Temperature setting for the BOIL OUT cycle 185°F to 208°F 200°F
Temperature which resets fryer & exits FILTER MODE to unlock
FILTER RESET 200°F to 325°F 290°F
fryer. Applies only when FORCE FILTER is ON
BOIL OUT TIME Length of time (mins) for BOIL OUT cleaning cycle 1 to 45 minutes 30
STIR ALARM If ON, the alarm issued when a specified % of programmed
ON OFF ON
ENABLE cooking time has elapsed, alerting to stir product.
If STIR ALARM ENABLE is ON, the alarm is issued after this
STIR ALARM % 10% to 90% 62%
percent [%] of cooking time has elapsed.
KEY BEEP ENABLE If ON, an audible sound is generated with each keystroke. ON OFF OFF

47
4.01.8 User Settings − continued
NAME DESCRIPTION RANGE DEFAULT
EnglishSpanish
LANGUAGE Selects controller display language English
French
If [ON], when selecting a Menu Preset for cooking the cycle will
COOK ON MENU automatically begin when basket side is selected. Reduces
ON OFF OFF
SELECT number of keystrokes needed to start cooking. ONLY available
on dual‐timer controllers.
If [ON], operator can add extra cooking time (after or during
[0] KEY EXTRA TIME ON OFF OFF
cycle) by pressing [0] + number of minutes.
4.01.9 PASSWORD Protection

It is possible to add PASSWORD protection to the controller. This feature is typically factoryset as DISABLED.
When PASSCODE ENABLE is [ON], the user is required to enter a password before they can access certain controller
functions, such as adding & editing settings, entering cook times, etc.
If you desire to enable password protection or have questions concerning the feature, call Giles Technical Services
at 800.554.4537 to request the passcode and receive instructions as to how to activate this feature.
4.01.10 Power Up Procedure
All hood filters must be properly installed, and the access cover must be in place and latched before the appliance
will powerup.
NOTE:
The appliance will NOT power‐up if the filter access cover is missing or ajar. The sides of the
cover must seat flush against the hood front in order to properly activate the a safety
interlock proximity switch.

48
4.01.10 Power Up Procedure − continued
1. Ensure that HEAT switch ① is in the [OFF] position.
2. Place the POWER switch ② in [ON] position. The green POWER light ③ will turn on and the hood fan begins
to run (an alarm may sound briefly until fan reaches speed).
3. Controller powersup and alarm sounds. The message “POWER FAILURE [PRESS START TO PREHEAT]” is shown
on the upper controller display screen ④. This is normal ... to ensure that an operator is present at the
appliance before heating elements will re‐energize when power is restored after a power failure. Press the
[START] key ⑤ to silence alarm and place fryer into PREHEAT mode. The last cook settings are shown on the
upper display screen. A red heat indicator on controller shows that fryer is heating, but until control panel HEAT
switch ① is placed in the [HEAT] position, the heating elements do not turn [ON].
DO NOT place HEAT switch ① in [HEAT] position unless the vat is filled with cooking oil (or water), see
Section 4.03, Cooking Procedures.
5. The E.A.C. Status [ON] light ⑥ should be ON (all other EAC status lights should be off).
6 2
4.01.11 Controller Errors & Alarms

Certain error conditions, such as open drain, low oil, high temp, etc., which can cause unsafe OLED
operation or damage to the unit will activate an alarm and display
error information on displays. Error codes are displayed on the
lower 7‐segment display screen (red graphic) and alarm information
& instructions are shown on the upper OLED display screen (blue
graphic). Heating elements are typically disabled when an alarm is
issued and remain so until the condition is corrected. Pressing the
[ALARM] key only silences the tone, but does not clear the error. Error codes and
their causes are shown on the following table. ALARM 7-Segment
See Section 4.01.11.1 for Error/Alarm Clearing steps.

49
4.01.11 Controller Errors & Alarms − continued
ERROR CODE DESCRIPTION Displayed PROBLEM

Drain valve is open, or not closed completely. When equipped,
OPEN DRAIN IS OPEN
basket lift will be raised.
CHECK OIL LEVEL, ENSURE VAT IS
A notification displayed after clearing an OPEN drain error to
FULL, IF FULL THEN PRESS
alert operator to verify oil level.
[START]
LOW OIL LEVEL – ENSURE VAT IS Oil level in vat is below the ADD line. Temp differential between
ER03 FULL (Element/Add Level element probe & ADD level probe is excessive, indicating low oil
Differential Warning) level.
LOW OIL LEVEL – ENSURE VAT IS
After ER03 is cleared, this is error is issued prompting user to
ER06 FULL – PRESS [START]
confirm oil level by pressing [START].
(Post ER03 Warning)
A notification error issued after element has cooled below the
MAX ELEMENT TEMP – PRESS
ER07 temp threshold, after MAX ELEMENT TEMP (ER19) alarm has
[START] (Post Warning)
cleared.
ER13 OIL PROBE Error Malfunction of the Variable Oil Temp Probe. Call for Service.
Malfunction of the Element Temp Probe that is attached directly

ER15 ELEMENT PROBE Error
to heating element. Call for Service.
Maximum heating element temperature has been exceeded.

ER19 MAX ELEMENT TEMP Error
This is a safety interlock ... NEVER bypass this probe!
ER21 BAFFLE FILTER MISSING Baffle Filter in hood is missing or misaligned.
ER22 CHARCOAL FILTER MISSING Charcoal Filter in hood is missing or misaligned.
Indicates airflow restriction in the hood. A filter is clogged or

ER23 FILTER CLOGGED
other obstructions are limiting airflow.
E.A.C. Collection Cell is dirty and not performing properly.

ER24 EAC CELL DIRTY
Requires cleaning. There can also be other causes.
Actual oil temperature deviates from setpoint by the guard band

ER25 GUARD BAND EXCEEDED
value. Factory default is 900°F ... This error should not occur.
Internal controller malfunction. Contact Giles Tech Service

ER37 EEPROM Error
(800.554.4537).
Internal controller malfunction. Contact Giles Tech Service

ER38 Internal ADC Error
(800.554.4537).
50
4.01.11.1 Clearing Controller Errors & Alarms
NOTE: When an issued erroralarm stops a cooking cycle before complete, it may become necessary to discard
any food product that was cooking at the time ... always comply with any local Standard Operating Procedures.
During the following steps, instructions indicating to press the [ALARM] key are only to silence the audible alarm
tone ... pressing the key DOES NOT clear an error. Tone will automatically silence after about 10 secs.
• OPEN: DRAIN OPEN If vat drain valve is open (even slightly) while fryer power is ON, alarm sounds, lower
display screen reads OPEn, upper display screen reads “ERROR ALARM ‐ DRAIN IS OPEN”. Power to heating
elements is shutdown and disabled until the error is corrected.
Press [ALARM] key ... clear alarm by fully closing the drain valve. After closing valve, the alarm sounds again and
upper display screen reads “CHECK OIL LEVEL, ENSURE VAT IS FULL, IF FULL THEN PRESS [START]”. This is a post
alarm notification, alerting the user to confirm that cooking oil in vat is still at the [FULL] level. Add oil if needed,
then press the [START] key to return to PREHEAT mode.
• ER03: LOW OIL LEVEL Alarm sounds, lower display shows Er03, upper display reads “ERROR ALARM ‐ CHECK
OIL LEVEL ‐ ENSURE VAT IS FULL”. Heating elements are shutdown until the condition is corrected. The detected
differential between a temperature probe at the [ADD] level mark and one attached to a heating element
exceeds an acceptable amount, indicating low oil level, which will greatly increase the potential for a vat fire!
Press the [ALARM] key ... disposition any food product being cooked, as required, and allow fryer to cool
adequately in order to reset fryer from error. Add oil to raise level to the [FULL] mark, as needed.
• ER06: LOW OIL LEVEL Posterror Warning After Er03 has been cleared, another alarm sounds. The lower
display shows Er06, upper display reads “CHECK OIL LEVEL ‐ ENSURE VAT IS FULL ‐ PRESS [START]”. This alarm
alerts operator to confirm that cooking oil in the vat is at the [FULL] level. If situation has been corrected, press
[START] key to enter PREHEAT proceed to continue cooking operations. Fryer will not heat until key is pressed.
• ER19: MAX. ELEMENT TEMP Temperature of heating element has exceeded the maximum allowed by the
controller. Alarm sounds, lower screen shows Er19, upper screen reads “ERROR ALARM ‐ MAX ELEMENT
TEMPERATURE”. Power to heating elements is shutdown. Press [ALARM] key ... elements must cool below the
allowable temperature threshold before error clears. Typical cause is low oil level (or no oil) that has exposed
the heating element. False alarms can occur when preheating cold oil at beginning of the day ... regularly stirring
the oil while preheating will help avoid such false alarms.
• ER07: MAX ELEMENT TEMP PostError Warning After an Er19 error has been cleared, a secondary notification
alarm occurs. The lower screen reads Er07, upper display reads “MAX ELEMENT TEMP ‐ PRESS [START]”. The
alarm only to alerts operator that a maximum element temperature error has occurred and is now cleared. Press
[START] key to enter PREHEAT mode ... heating elements will not turn ON until [START] key is pressed.
• ER21: BAFFLE FILTER MISSING Alarm sounds, lower screen reads Er21, upper screen reads “ERROR ALARM ‐
BAFFLE FILTER MISSING”. Indicates that the baffle filter is missing from hood, or installed improperly. Heating
elements are disabled until condition is corrected. Inspect filter chamber ... install filter if missing, or remove and
reinstall filter to ensure that it is properly aligned to activate the interlock switch. Error will clear when filter is
properly installed. See Section 6.01.2. & 6.01.3, Baffle Filter Removal & Installation.

51
4.01.11.1 Clearing Controller Errors & Alarms − continued
• ER22: CHARCOAL FILTER MISSING Alarm sounds, lower screen reads Er22, upper screen reads “ERROR ALARM ‐
CHARCOAL FILTER MISSING”. Indicates that charcoal filter is missing from hood, or installed improperly.
Heating elements are disabled until condition is corrected. Inspect filter chamber ... install filter if missing, or
remove and reinstall filter to ensure that it is properly aligned to activate the interlock switch. Error will clear
when filter is properly installed. See Section 6.01.10, Charcoal Filter Installation.
• ER23: CLOGGED FILTER Alarm sounds, lower screen reads Er23, upper screen reads “ERROR ALARM ‐ CLOGGED
FILTER”. Indicates there is insufficient airflow through the hood to maintain capture performance. Typically due
to a clogged charcoal filter, which must be replaced (cannot be cleaned). Other obstructions or conditions can
also cause this alarm. Heating elements are disabled until the condition is corrected. Install a NEW charcoal
filter and/or inspect hood for other obstructions. Error will clear when proper airflow is restored. See Section
6.01.10 & 6.01.12, Charcoal Filter Installation & Replacement.
• ER24: E.A.C. DIRTY Alarm sounds, lower screen reads Er24, upper screen reads “ERROR ALARM ‐ CLEAN THE
EAC”. Indicates that the electronic air cleaner (E.A.C.) collector cell is excessively dirty, missing, improperly
installed, damaged, or has malfunctioned. Heating elements are disabled until the condition is corrected. Clean
and inspect the E.A.C. cell. Error will clear when condition is resolved. See Section 6.01.6 through 6.01.9, EAC
Filter Operation & Cleaning.
DO NOT rely on this alarm notification as a signal to clean the E.A.C. cell ... as best practice, it must be cleaned
DAILY in order to maintain optimum performance.
Alarms & errors can be caused by component malfunctions or failures, as well as operational issues. If an error
condition cannot be cleared using the processes described, a factory‐authorized service technician may be
required. Call Giles Technical Support at 800.554.4537 for assistance in locating a service company near you.
4.02 Cooking Procedures

The following sections explain “best practice” procedures for cooking with the GBF‐50‐VH Electric Ventless Fryer.
Certain optional features are explained where applicable ... your particular equipment may or may not have these
options installed.
This is a multipurpose fryer with an integral recirculating hood. It is designed to efficiently cook a variety of menu
favorites, from french fries & veggies to poultry & seafood. Every food product has specific procedures for
preparation and cooking, and all food service businesses have their own sets of specific standard practices. When
preparing, cooking and serving your products, be sure to follow all of the standard operating practices & guidelines
of your particular business, as well as the appliance operating procedures presented in this manual.

52
4.02.1 Filling & Preparing Fryer for Cooking
NOTE:
Before using the fryer for first time, be sure all installation steps have been properly performed, including
necessary cleaning (boil out, washing accessories, etc.).
The steps described here assume starting with a clean, empty fryer (baskets & crumb screen removed).
2 6
1. Place POWER switch ① in [ON] position ... green POWER light and controller ② turn ON. Controller boots up
as explained in Section 4.01.10 and the alarm sounds. DO NOT press the [START] key as prompted by controller
... only press [ALARM] key ③ to silence alarm.
2. Ensure that the HEAT switch ④ is in the [OFF] position. DO NOT place switch in [HEAT] 5
position at this time.
NOTE:
After powerup, should the “DRAIN OPEN” alarm sounds & the error message shows on
upper display ②, check drain valve handle. Closing fully should reset error alarm, press the
[ALARM] key and continue.
3. Even if there is no alarm, it is still best to open lower cabinet door and confirm that the
drain valve ⑤ is CLOSED ... firmly in the left‐most position to a stop.
IMPORTANT! Fryer will not heat unless valve is fully closed and the valve interlock is engaged.
4. Fill cook vat with your preferred fresh liquid frying shortening. Fill ONLY to [ADD] level
mark at this time to allow for expansion as oil heats.
DO NOT use solid shortening in this fryer.

53
4.02.1 Filling & Preparing Fryer for Cooking − continued
5. After filling vat with fresh oil, manually set the desired cooking temperature as described in Section 4.01.3.
When upper display screen ② returns to the POWER FAILURE message, press [START] key ⑥.
6. Place HEAT switch ④ in the [HEAT] position ... amber control panel HEAT light ⑦ turns ON and oil begins
heating. Upper controller display screen will indicate PREHEAT and lower screen displays the actual realtime
temperature as the oil heats.
Cooking oil becomes extremely HOT! Always wear thermal protection, such as oven mitts
or gloves, when stirring or working near the vat of hot oil.
7. Oil should be stirred frequently while heating to help prevent false high limit temperature alarms. This is
especially important during the initial heatup of the operating day when shortening is cool and thickened.
8. When cooking oil reaches the programmed setpoint, alarm sounds and upper display ② reads “ALARM ‐ STIR
OIL”. Press [ALARM] key ③ and controller enters into a 10 second delay. Immediately, stir oil vigorously with
the provided stirring tool. This will help to eliminate cool zones and promote even heating throughout the total
volume of oil. If temperature drops below setpoint while stirring, the controller will remain in PREHEAT mode
until temp returns to setpoint. At that time, or if temp did not drop significantly, alarm sounds a second time
and the upper display reads “ALARM ‐ SETPOINT REACHED” ... press the [ALARM] key. Controller enters READY
state ... temperature value displayed on the lower display screen changes to show the setpoint
temp. Oil should now be evenly heated and ready for cooking.
9. Confirm oil level ... it should now be at, or near, the [FULL] level mark. If not, add fresh oil to
fill to the mark. Stir oil and if the HEAT light turns ON again, continue stirring and wait until it
turns OFF before cooking.
4.02.2 Loading Product for Cooking

1. Place support/crumb screen ① into vat ... handles to the side. Screen sits on brackets attached to the vat sides.
2. The standard GBF‐50‐VH fryer is equipped with a basket hanger rack on the back cabinet header ... hang empty
baskets ② there.
Optional Auto‐basket Lifts: If the basket lift option is installed on your fryer, hang the cooking baskets onto the
basket carrier arms ③. There is no hanger rack when basket lifts are installed.
If you wish to use the basket lift feature when cooking, set the control panel LIFT switch ④ in the [LIFT]
position. The switch is not present on control panel unless the option is installed.
3
2
+
1
4

54
4.02.2 Loading Product for Cooking − continued
NOTE:
When NOT intending to use installed basket lifts, manually raise to the full [UP] position (see Section 4.01.7.1,
Manual Operation) and set the LIFT switch to [OFF]. The carrier arms can now be used as basket hangers.
Oil level MUST be maintained between [FULL] & [ADD] levels when operating. An oil level
consistently below [ADD] causes the controller to issue a LOW OIL LEVEL alarm and
shutdown the heating elements to prevent possible vat fire ... elements will remain disabled until the condition
corrected and fryer is reset.
Use extreme caution when dropping product into HOT cooking oil! There is potential for
severe burn injury should oil contact unprotected skin, such as an unexpected splash.
Introducing foods containing excessive moisture, or attempting to cook larger than recommended load sizes,
may lead to surge boiling, which can cause an overflow of HOT oil. Always observe how hot oil is reacting when
product is loaded, before proceeding.
Best Practice recommendation: When loading fryer for cooking, first place uncooked product into a fry
basket, then place loaded basket into the hot oil. Using this method will help avoid possible burn injury
while handling food near hot cooking oil ... an unexpected splash or lack of operator attention could result
in skin contact with hot oil and cause serious injury.
Product can be placed into a basket that has already been placed into the vat, but this is NOT
recommended. If using this method, always wear appropriate thermal protective gear (mitts or gloves) to
avoid possible injury.
3A. Standard Fryer w/ Basket Hanger Rack: 8
Place empty basket(s) onto the hanger rack.
3B. Fryer w/ Optional Basket Lifts:

Raise basket lifts as needed ... press [BASKET] key ⑦, then keypad
[2] UP key ⑧, then select which lift to raise, pressing [4], [5] or [6]
key. Hang empty basket(s) onto basket carrier arm ... the lift will 7
automatically lower when a cooking cycle is started.
4. Load product to cook into the basket.
5. Set controller to the proper cooking time for the product. Either
manually set a TIME or select the appropriate programmed Menu Item
Preset. See Section 4.01.4, Manually Setting the Cook Time or Section
4.01.5.2, Selecting a Menu Item Preset for Cooking.
If you are cooking different items at the same time, each basket can be
set for a different cooking time ... each item must require the same
cooking temperature.
NOTE: If user setting “COOK ON MENU SELECT” is set [ON], the cook
cycle will begin immediately when the basket side is selected for a
chosen menu preset, without any additional keystrokes.

55
4.02.3 Cooking Cycle Process
1. The controller cook settings will be shown on the upper controller display ... item
name/cook time for each side, cook temp setpoint & the READY notification.
Always wear thermal protective gear, such as gloves or oven

mitts, when handling hot baskets.
2A. Standard Fryer w/ Basket Hanger Rack:

After product is loaded in basket, press [START] key. You are prompted to
select the basket side to start ... press keypad [4], [5] or [6] to select ...
programmed cook time begins to count down on the lower display.
Immediately, place the selected basket into vat, sitting it on the support
screen in vat bottom.

After product is loaded in basket on carrier arm, press [START] key on
keypad. You are prompted to select the basket side to start ... press keypad
[4], [5] or [6] to select. The selected basket automatically lowers into vat
and the programmed cook time begins to count down on the lower display.
3. The upper display shows the message COOKING LEFT, RIGHT or BOTH.
Lower display shows the cook time remaining as countdown proceeds.
NOTE: If cooking different items in each basket, the second basket’s cooking
cycle is started in the same manner, except the prompt for selecting side will
only show the one remaining choice.
If timers are running different cycles, press the [TIME] key twice
x2 to swap controller display between the two timers. Timer
indicator changes to show which side is being displayed.
STIR ALARM: 9
Step #4 applies only if following user settings are set as shown (see Section
4.01.8):
STIR ALARM ENABLE = [ON]
STIR OVERRIDE = [NORMAL] for the menu preset being used.
•• OR ••
STIR ALARM ENABLE = [OFF]
STIR OVERRIDE = [FORCE] for the menu preset being used.
If not set as shown, STIR ALARM will not sound, however Best Practice
recommendation is that product be stirred, during the latter portion of a
cooking cycle, to help promote even cooking and to keep pieces from sticking
together.
4. The STIR ALARM sounds after a preset amount of the programmed cook time has elapsed; upper display reads
ALARM ‐ STIR [LEFT] [RIGHT] [BOTH] SIDE. Press [ALARM] key and use the provided utensil ⑨ to stir the
cooking product. If basket lift is in use, be sure that basket does not become dislodged from the carrier arm
while stirring.

56
4.02.3 Cooking Cycle Process − continued
5. When programmed cook time has elapsed, the alarm sounds and
upper display reads ALARM DONE COOKING ‐ [LEFT] [RIGHT] [BOTH].
6A. Standard Fryer w/ Basket Hanger Rack:

Press [ALARM] key to silence. Promptly remove proper basket from
vat and hang it onto the basket hanger rack.
Appropriate basket is automatically raised from the vat by the lift. Std Hanger Rack
Press [ALARM] key to silence. If choosing not to use the installed lifts,
promptly remove basket manually and hang it onto a raised basket
carrier arm.
7. Typically, local Health Department and specific food service operating
procedures will require that the internal temperature of cooked
protein products be tested as an indication of doneness before sale to
customers. Cooked products should be checked after the cooking
cycle ends ... it is best to check with an instant read probestyle food
thermometer. Should the temperature be lower than required,
additional cooking time is needed.
The fryer controller has a selectable feature that will allow operator
to easily add additional cooking time by simply pressing the [0] key + Optional Basket Lift
# mins to add ... controller will prompt to select which side to add the
time. This can be done either after the cycle is complete, or while it is
still active. The feature is only available, when the user setting “[0]
KEY EXTRA TIME” is set to [ON]. See Section 4.01.8.
8. Allow cooked product to adequately drain, then dump into an
appropriate dump station or food service pan.
9. To continue cooking, return to Section 4.02.2, step #2.
To shutdown unit, see Section 4.05, Normal Shut‐Down.
57
4.03 Filtering Used Cooking Oil
The following section explains the process for filtering and reconditioning used cooking oil with the onboard Oil
Filtration System. The system pumps the used oil through filtering media & filter aid compound contained in the
filter pan and circulates it back to the fryer vat. Routinely performing this procedure can, in most cases, increase
the useful life of cooking oil by as much as 50%. As a Best Practice, Giles recommends that oil be filtered after
every 4th load cooked.
The controller features a configurable FORCE FILTER function, which can be set to force operating personnel to filter
oil after a specific number of loads have been cooked. The feature is enabled and configured in user settings,
Section 4.01.8:
• FILTER COUNT 1 to 20 • Factory set default is 4.
Specifies the number of cook cycles allowed before Force Filter is activated.
• FORCE FILTER [ON] or [OFF] • Factory set default is [ON].
[ON] = After completing cook cycles equal to FILTER COUNT, alarm sounds and message “ALARM ‐ MUST
FILTER OIL” is displayed on upper controller display screen and controller enters FILTER MODE ... pressing
[ALARM] key silences alarm. Fryer is disabled from continued operation until cooking oil is properly filtered.
[OFF] = After completing cook cycles equal to FILTER COUNT, alarm sounds and message “ALARM ‐ FILTER
OIL” is displayed on upper screen. Pressing [ALARM] key silences alarm. Fryer returns to READY state and
cooking can continue, however the alarm and notification message will continue to be issued after every
subsequent load cooked until oil is properly filtered.
• FORCE FILTER SNOOZE [ON] or [OFF] • Factory set default is [OFF].
Only active when FORCE FILTER is set [ON].
[ON] = Allows cooking one (1) additional load of product after FILTER COUNT is reached ... after the
additional cook cycle is used, fryer enters FILTER MODE and is disabled until oil is filtered.
[OFF] = No additional cook cycle is allowed.
Menu item presets have an available FISH FILTER feature, which is typically used for seafood items when it is
desirable to minimize potential for flavor transfer to other foods being cooked on the same fryer. Set [ON] to
override the global FORCE FILTER setting and place fryer into FILTER MODE after only (1) batch of the particular
menu item is cooked. For details, see Section 4.01.5.1, Editing a Menu Item Preset.
DO NOT attempt to perform the filtering process when shortening is cool. Doing so can
cause the filter system to clog and possibly damage the pump. Oil temperature should be at
least 200°F (93°C) before being pumped through the system.
Always wear thermal protection, such as gloves or oven mitts, when filtering cooking oil ... fryer parts inside
the cabinet may be very HOT!
1. Fryer alarm sounds after cooking the number of loads specified by [FILTER COUNT].
2A. FORCE FILTER is OFF, upper screen ① shows “ALARM ‐ FILTER OIL” ... press [ALARM] key 1 3
② to continue. As notification, this alarm occurs after each
subsequent cook cycle, until cooking oil is filtered.
2B. FORCE FILTER is ON, upper screen shows “ALARM ‐ MUST FILTER OIL” ...
press [ALARM] key. Fryer enters FILTER MODE and is locked out from
continued operation until cooking oil is filtered, which resets fryer.
2
3. Place HEAT switch ③ in [OFF] position. IMPORTANT! Controller power
must remain ON during the filtering process ... leave POWER switch in
ON position.
58
4.03 Filtering Used Cooking Oil − continued
4. Open cabinet door, disconnect the filter pan hose ④ (push in white locking ring
while pulling hose from connector) ... remove filter pan ⑤ from unit.
4
5. Remove cover from pan and verify that filter media is properly installed with hold‐
down frame securely locked down. Standard filter media for this fryer is a reusable
stainless mesh screen ... alternative is one (1) sheet of, properly sized, disposable
filter paper. Should any residue from previous filtering be present on media surface,
use the provided crumb shovel to remove and discard.
6. Evenly distribute approximately 5 ozs. of a suitable filter powder product over the 5
media surface. Use of a quality filter aid compound is essential for removing soluble
impurities and reconditioning the oil. Portion pack Filter Powder is available from
Giles dealers/distributors ... Item #72004.
7. Replace cover and reposition the assembled filter pan under unit. Reconnect filter pan hose
(push in white locking ring while inserting brass fitting into coupling). Ensure that hose fit is
tight and secure.
During the next steps, cooking oil is drained from the vat into filter pan, exposing heating
elements, which can increase the risk of fire. Although fryer has safety interlocks which
disable the elements anytime drain valve is opened, as a further safeguard, always place HEAT switch in the
[OFF] position prior to draining. NEVER USE THE DRAIN VALVE AS AN “ON/OFF HEAT SWITCH”.
Never disconnect and attempt to remove the filter pan from unit while it contains HOT
cooking oil.
IMPORTANT!
POWER switch must remain [ON] during the entire filtering process. When drain is opened, controller will
issue the DRAIN OPEN error & alarm ... press the [ALARM] key to silence and continue.
8. Verify that HEAT switch remains in the [OFF] position. In the lower cabinet
place the pump diverter valve handle ⑤ in the [OIL RETURN] position
5
(horizontal). Slowly move drain valve handle ⑥ to the [OPEN] position (fully
right to stop). Oil should begin draining into the filter pan.
6
9. When oil has completely drained into filter pan, place the PUMP switch ⑦ in
the [PUMP] position.
NOTE:
If oil does not readily drain, use the provided round bristle drain brush to break
up crumbs or residue that may be clogging the drain valve.
While draining, be sure filter pan cover remains in place to help contain oil
splash & splatter.
10. Dirty oil is pumped through the media/filter aid and is circulated
back to the vat. Leave drain valve open ... allow
continuous circulation for about 5 minutes to act as 7
a “crumb flush”. During this time, use the provided
heatresistant pot brush & L‐bend brush to dislodge
cooking residue and crumbs from vat sides and
heating elements ... allow residue to be flushed
down drain into the filter pan. Continued on Next Page
59
4.03 Filtering Used Cooking Oil − continued
11. After about 5 minutes, return drain valve handle to the [CLOSE] position ... vat begins refilling. Allow filtered
and reconditioned oil to fill vat. Filling is complete when the oil return nozzles located in the vat bottom begin
to blow air into the oil.
NOTE:
When closing the drain valve, controller will issue the notification alarm and displays “CHECK OIL LEVEL,
ENSURE VAT IS FULL, IF FULL THEN PRESS [START]” on upper display screen. Press [ALARM] key to continue.
12. After vat has refilled, return PUMP switch ⑦ to the [OFF] position.
13. Check and verify oil level in the vat; add oil if level is below [FULL].
14. Press the [START] key to clear the controller alarm code.
If FORCE FILTER is [ON], controller should now be reset and the fryer is ready to PREHEAT for cooking.
15. Return HEAT switch to the [HEAT] position and oil will begin reheating to setpoint temperature.
Always wear thermal hand protection when performing the following . Parts can be
excessively hot!
16. After refilling vat, remove filter pan (see Step #3). Use provided Crumb Shovel ⑧ and taking care not damage
or puncture the filter media, scoop filter sediment from the surface and dispose. It is not essential that filter
media be refreshed after each filter cycle, but as a Best Practice, Giles is recommends that the pan be cleaned
and filter media be refreshed at least daily (see Section 5.03).
8
17. Reinstall filter pan in fryer cabinet.
18. To continue cooking, return to Section 4.02, Cooking Procedure.
To discontinue cooking, see Section 4.04, Fryer Shut‐Down.
NOTE!
FILTER REMINDER ‐ when FORCE FILTER feature is turned [OFF] and after FILTER COUNT is exceeded, the
controller still issues a filter reminder & displays notification at the completion of every subsequent load
cooked. The message “PLEASE FILTER OIL” will be displayed on the upper display screen. If filtering must be
delayed until another time, press the [START] key to continue.
60
4.04 Fryer Shut−Down
1. Place HEAT switch ① in the [OFF] position. 1
2. Place POWER switch ② in the [OFF] position.
3. Complete all other end of day procedures as prescribed by

your specific Standard Operating Procedures.
Emergency Shut‐Down:
In case of an emergency, disconnect electrical power supply to the appliance at the building main electrical panel,
and/or follow all standard emergency procedures prescribed by your specific Standard Operating Procedures.
61
62
Cleaning GBF−50−VH Electric Fryer
5. Cleaning
The following section describes cleaning & maintenance procedures, which are needed to help keep the appliance
in good operating condition. General cleaning should be performed daily and other specific activities should be
preformed as described in the following. Cleaning and maintenance for the Ventless Hood system is discussed in
Section 6.
• DO NOT wash down the unit (interior or exterior) with water from a spray hose. Control panel is “liquid‐
resistant”, but is not “wash‐down safe”.
• Failure to comply with DANGER notices will result in death or serious injury, equipment or property damage,
and void the warranty.
5.01 Removing Waste Cooking Oil from Fryer

The following steps explain procedures for removing and disposing of waste cooking oil. Depending on filtering
practices and types and quantities of foods cooked, the best practice is to change the fryer cooking oil every 7 to 10
days in order to maintain performance and food quality. Used oil also must be removed before cleaning the fry vat
using the boil‐out procedure.
Never attempt to pump cold shortening. Doing so can clog and damage the filter pump. Oil
should be heated to at least 200°F (93°C) before attempting to pump.
1. If shortening is cold, heat to at least 200°F (93°C).

2
2. Confirm that POWER switch ① is in the [ON] position, and be
sure that the HEAT switch ② remains is in the [OFF] position, at
this point.
3. Ensure that filter pan and pan cover ③ are in place. Confirm that
filter pan hose ④ is properly connected at the hose coupling and
secure. Verify that the pump diverter valve handle ⑤ is in the
1
[OIL RETURN] position.
Never disconnect and attempt to remove the Filter Pan

5
from unit while it contains HOT cooking oil.
During the next steps cooking oil will be drained from the 6
vat, exposing the heating elements, which can increase the
4
risk of fire. Although fryer has safety interlocks which disable the elements
anytime drain valve is opened, as a further safeguard, always place HEAT
switch in the [OFF] position prior to draining. NEVER USE THE DRAIN VALVE
3
AS AN “ON/OFF HEAT SWITCH”.
4. Slowly move drain valve handle ⑥ to the [OPEN] position (fully right to the
stop). Allow waste oil to completely drain into filter pan.
Should oil not readily drain, use the provided round bristle straight brush to
clear obstructions from the drain opening & valve.

63
GBF−50−VH Electric Fryer Cleaning
5.01 Removing Waste Cooking Oil from Fryer − continued
Giles Oil Caddy (not included) is depicted here for oil disposal ... any
suitable disposal system can be used.
10
7
8
11 12
9
5. Connect the provided oil discharge hose ⑦ to the discharge hose coupling ⑧ inside cabinet (push in white
locking ring while inserting brass hose fitting). Be sure that the connection is tight & secure.
6. Place the discharge wand nozzle securely into an appropriate hot oil disposal container ⑨.
7. Set the pump diverter valve handle ⑩ into the [DISCHARGE HOSE] position (vertical).
Thermal hand protection, gloves or mitts, should be worn when handling the discharge hose during and after
pumping oil. Some parts of the hose assembly can become very hot.
While pumping HOT oil, the operation must be monitored closely to avoid possible spillage.
8. Place the PUMP switch ⑪ in the [PUMP] position and allow all waste cooking oil to pump into the disposal
container. When the filter pan has been emptied, return PUMP switch to [OFF] and place POWER switch ⑫ to
[OFF].
9. Return drain valve handle to the [CLOSE] position and return the pump diverter valve handle to the [OIL
RETURN] position.
10. Disconnect discharge hose from coupling (push in white locking ring while pulling hose from coupling). Hold
hose upright and drain any oil remaining in it into the disposal container.
11. Allow filter pan to cool sufficiently, then remove it from fryer, disassemble and clean thoroughly, see Section
5.03.

64
5.01 Removing Waste Cooking Oil from Fryer − continued
12. See Section 5.02, Boil‐Out Procedure.
To shutdown unit, see Section 4.04, Fryer Shut‐Down.
IMPORTANT!
As a general rule, the boil‐out procedure should immediately follow removal of waste cooking oil, before fryer is
refilled with fresh oil. Should this not be possible, as a “best practice” we suggest that as much oil residue as
possible be removed from the vat sides & elements using absorbent, disposable, paper wipes.
THERMAL PROTECTIVE GEAR MUST BE WORN.
5.02 Boil−Out Procedure − Cleaning the Vat

Boil‐out is a procedure used to clean/degrease the vat and heating elements. It must be performed before cooking
with a new fryer, and should be performed promptly before refilling fryer with fresh cooking oil after waste oil is
removed and discarded.
For proper maintenance and to ensure satisfactory operation and food quality, a boil‐out should typically be
performed every 7 to 10 days, however, exact timing of oil replacement is dependent on many factors. Oil quality
test kits can help accurately determine oil condition ... available from most restaurant supply providers.
• The procedure does not require a rolling boil. As a “best practice”, DO NOT leave fryer unattended during the
procedure. Closely monitor the process as a safeguard against an accidental overflow ... overflow can cause
serious damage to the equipment.
• When performing the boilout procedure, always don personal protective equipment (PPE), such as thermal
gloves/mitts, faceshield, latex apron, etc.
• When using fryer degreasing/cleaning products, closely follow the manufacturer’s usage instructions. Many
such products may contain chemicals that require special precautions. Improper use can cause damage to
equipment and/or personal injury.
1. Remove waste cooking oil from the fryer as previously described. 1

2. Place the HEAT switch ① and POWER switch ② in the [OFF]
positions.
3. Using absorbent wipes, clean as much waste oil residue as
possible from vat and heating elements, then begin filling vat
with clean ambient temperature water.
4. Use a reputable Fryer Cleaner/Degreaser product and follow the
product manufacturer’s usage instructions, complying with all 2
3 4
hazard warnings and precautions.
Add the recommended amount of product to the water as vat
fills and stir to mix. DO NOT fill above the vat [FULL] mark.
Boil‐Out Fryer Cleaner is available from Giles
dealers/distributors ... Item number: #72003‐1 for (1) 8‐lb Jar ...
#72003 for case of (4) 8‐lb Jars.

65
5.02 Boil−Out Procedure − Cleaning the Vat −continued
Closely follow the product manufacturer’s usage instructions and hazard warnings. Some
cleaners may contain caustic chemicals and require special precautions when used.
Improper use could damage the fryer and potentially pose a risk of personal injury.
5. Place POWER switch ② in [ON] position and HEAT switch ① in 1

[HEAT] position. 5
6. After controller powersup and alarm sounds, press [START] key
⑥ to enter PREHEAT mode ... control panel amber HEAT light
turns ON and cleaning solution begins heating. Upper controller
display reads “PRESS [BOIL] ‐ GO TO BOIL‐OUT”. Press the 6
[BOIL] key ⑤ to place fryer into BOIL OUT mode. Temp setting
automatically changes to 200°F (93°C) and timer begins
countdown for 30 mins. Allow the boil out cycle to completely 2
run.
Boil Out settings are factory‐preset, but can be changed to your
specific preference in user settings, Section 4.01.8.
During the boilout cycle, use the various provided heatresistant
brushes to scrub residue from heating elements, vat sides &
bottom. Use Lbend brush can clean under heating elements.
7. At the completion of the boil‐out cycle time, the alarm
sounds and the upper controller display screen shows the
message “DONE COOKING”.
8. Press the [ALARM] key ⑦ to silence alarm.
9. Controller exits BOIL OUT MODE and temperature setpoint
will reset to 50°F.
7
IMPORTANT! Controller automatically lowers setpoint to
50°F. After boil‐out is complete, setpoint must be re‐
entered for the proper cooking temperature.
To exit BOIL OUT MODE
10. Return the POWER switch and HEAT switch to the [OFF]
before completion,
position.
press [CLEAR] + [4]
NEVER drain boil‐out solution into filter pan or pump it through filter system with filter
pump. The solution is caustic and will damage the pump and other components. Such
damage is not covered by the factory warranty!
11. Disconnect and remove filter pan from the unit.

12. Position a suitable heat‐resistant container ⑧ (not provided) beneath the fryer drain
tube. Common plastic containers are generally not acceptable for collecting hot boil‐
out solution, as they can crack or melt. Metal containers are best.
If an adequate floor drain is available in the kitchen near the fryer, it is acceptable to
slowly drain solution onto floor and squeegee to the drain ... a helper will be needed. 8
NOT THE FILTER PAN

66
5.02 Boil−Out Procedure − Cleaning the Vat − continued
13. Slowly move the drain valve handle ⑨ to the [OPEN] position.
14. As vat drains, continue to scrub sides, bottom, and heating elements as
needed to remove residue.
9
After draining, flush the vat thoroughly with warm clean water to rinse.
Take care not to damage the temperature probes protruding through the
front wall of the vat.
When using a catch pan, give proper attention ... close

drain, empty it as needed, then continue.
If using floor drain, have a helper keep drainage squeegeed to drain.
IMPORTANT: After draining and flushing, it is important that fryer plumbing be

purged to remove as much cleaning solution as possible. Failing to do so can
result in contamination that will cause oil to “boil” and splatter excessively
when heated to cooking temperature.
PURGING:
15. Set pump diverter valve to the [OIL RETURN] position.
16. Leave the drain valve handle ⑩ in [OPEN] position.
17. Place PUMP switch in the [PUMP] position and allow pump to run for 1 ‐ 2 minutes. During this time water
and/or boilout residue may be discharged from the filter pan coupling or into the vat to drain into the catch
container (or floor).
10

67
5.02 Boil−Out Procedure − Cleaning the Vat − continued
18. Completely dry vat sides/bottom and heating elements using clean,
absorbent, disposable paper wipes, or sanitized towels.
10
19. Return drain valve handle ⑩ to the [CLOSE] position.
20. Clean the filter pan and refresh filter media, see Section 5.03,
Cleaning the Filter Pan & Refreshing Filter Media.
13
21. Replace pan cover ⑪ and position filter pan ⑫ under unit.
Connect hose ⑬ to the filter pan coupling (push in white ring while
inserting hose fitting) ... connection must be tight and secure.
22. Restart fryer for cooking activities, see Section 4.02.
11
NOTE:
At its completion, the automatic boil‐out program resets the
cooking temperature setting to 50 ° F . Be sure to set a correct
temperature before attempting to cook.
12
5.03 Cleaning the Filter Pan & Refreshing Filter Media

This section explains the procedure for cleaning the filter pan and refreshing the filter media, using either reusable
stainless steel screen or disposable filter paper. As a “best practice”, this should be performed at the end of every
day’s operation and as part of every fryer boil‐out procedure.
FILTER MEDIA NOTE:

• Reusable Stainless Steel Filter Screen is a standard feature for the GBF‐50‐VH Fryer after removing &
discarding residue, wash screen in sink, using ONLY a stiff bristle brush and clean hot water. DO NOT use soaps
or other cleaners, as it is extremely difficult to rinse thoroughly enough to remove all soap residue from the
screen ... residue could subsequently transfer to the cooking oil.
Shake off excess water and blot dry with clean absorbent towel (ideally screen should dry overnight). Reinstall in
pan when completely dry.
With proper use and care, the reusable filter screen should provide a long service life. It should be replaced if
torn, punctured, frayed, or if the silicone edge gasket is significantly damaged.
• Filter Paper Use only one (1) fresh sheet of properly sized filter paper. DO NOT use paper and screen together
at the same time.
Filter Paper is available from Giles dealers/distributors ... Item Number #65871 (Case of 100 sheets).

68
5.03 Cleaning the Filter Pan & Refreshing Filter Media
Wear thermal protection to protect hands from potentially hot parts.
NOTE:
For best cleaning results, GILES recommends using a non‐toxic, non‐detergent, bio‐degradable degreasing
cleaner, such as SIMPLE GREEN® Crystal Foaming Spray Cleaner/Degreaser along with hot water, to clean and
degrease the filter pan and components. DO NOT use cleaner on the reuseable filter screen.
1. Remove filter pan from fryer, as needed.

1
2. Remove and clean the pan cover ①. Dry thoroughly.
3. Use the provided metal crumb shovel ⑤ to remove as much

accumulated filter sediment as possible from the filter media 3
surface, particularly around outer edge near hold‐down frame
③ to help prevent the sediment from falling into bottom of 4
the pan when soiled media is removed ... excessive residue
getting into the filter plumbing can cause the pump to clog.
4. Turn four locking levers ② to disengage the hold‐down 6

frame ③. Lift frame out of pan.
5. Remove dirty filter media ④, careful to keep loose residue

from falling through the perforated filter support screen in the
pan bottom.
6. Thoroughly clean the filter pan ⑥ & hold‐down frame ③. 2

Rinse thoroughly with plenty of water. Flush out pan hoses
and any sediment that may have fallen through the perforated
screen ... be sure to drain water from hoses.
Dry pan assembly thoroughly. 5
IMPORTANT!
The perforated filter support screen in the filter pan bottom is NOT a filter. A suitable filter media (reusable
screen or filter paper) must be used to filter the oil and avoid possible equipment damage. Failure to use proper
filter media can void the factory warranty!

69
5.03 Cleaning the Filter Pan & Refreshing Filter Media − continued
7. Reassemble filter pan, using (1) new sheet of filter paper, or the cleaned
reusable filter screen. NEVER use filter paper AND filter screen at the 8
same time ... pump will NOT function properly. Be certain that filter media
is placed properly underneath the hold‐down frame and that the frame is
7
locked securely in place by engaging all (4) levers.
8. Replace pan cover ⑦, position assembled filter pan under unit and re
connect hose ⑧ at the filter pan quickcoupling (push in white ring while
inserting hose fitting). The connection must be tight and secure for proper
operation.
70
Ventless Hood GBF−50−VH Electric Fryer
6. Ventless Hood
This section explains operation, maintenance and service procedures for the Ventless Hood system of the GBF‐50‐
VH Electric Fryer. The integral hood section of the appliance is a Type‐1 recirculating hood system that removes
greaseladen cooking vapors from the air and has an activated charcoal filter to help control odor. Clean, filtered air
recirculates back into the room. The system is selfcontained with builtin fire suppression and does not require
ducting to vent exhaust to the outside. Ventless hood appliances are NOT acceptable for all situations, so to ensure
satisfactory performance, the appliance site and installation process must comply with stringent requirements, as
explained in GILES Hood Approval Document (HAL).
6.01 Hood Filters

The following explains each filter in the Ventless Hood system and describes removing & installing, cleaning, and
alarm conditions that can occur if not properly maintained. Filter maintenance & cleaning must be performed as
prescribed to keep the air cleaning system operating at peak performance.
IMPORTANT! The appliance will NOT power‐up if the filter access cover is not installed properly. The sides of the
cover must seat flush against the hood front, and fryer will NOT heat unless ALL hood filters in place.
6.01.1 Hood Filter Table

Maintenance
Filter How to Remove How to Clean How to install
Required
Baffle Filter Clean Daily Section 6.01.2 Section 6.01.3 Section 6.01.2
EAC Filter Clean Daily Section 6.01.2 Section 6.01.4 Section 6.01.2
Replace approx.
Cannot be cleaned
Charcoal Filter every 30 days Section 6.01.2 Section 6.01.2
REPLACE ONLY
P/N 31963
• BAFFLE FILTER: First stage of the air cleaning system. Entraps and collects large airborne grease particulate
generated by frying. Condensate drains into a collection trough and is collected in a drip cup beneath the filter.
This filter is generally dishwasher safe.
• ELECTRONIC AIR CLEANER [E.A.C.] COLLECTOR CELL: Second stage of the system. Contains fine ionizer wires and
a bank of thin metal collection fins. Electronic system negatively charges grease particulate in the air stream,
allowing it to be electrostatically captured and collected by the fins. The cell must be cleaned EVERY DAY as
described later in this section. Fryer is equipped with an E.A.C. Cleaning Timer that reminds operating personnel
to clean the cell ... failure to routinely clean it can cause the fryer to be shut‐down and locked out from
continued operation until cleaned.
• CHARCOAL FILTER: Third stage of the system. The activated carbon filter helps to control cooking aromas in the
exhausted air. This filter is single use, consumable item and MUST be replaced approximately every 30 to 40 days
depending on cooking activity and hours of operation. Filter CANNOT be cleaned and reused.
NOTE: No filter will completely remove cooking odors generated by frying operation.
71
GBF−50−VH Electric Fryer Ventless Hood
6.01.2 Filter Removal & Installation
Baffle Filter & E.A.C. Collector Cell have sharp exposed edges, which may cause cuts. Use
due caution when handling and cleaning. Heavy duty rubber gloves are advised.
1. All Filters, Baffle ②, E.A.C. Cell ③ & Charcoal ④ are accessed by removing the Filter Cover ①. To remove,
unlatch, lift bottom edge, move upward slightly to disengage from flange at top and lift off.
2. All filters fit into the guide channels ⑤ inside the plenum filter chamber. To remove a filter, grasp it and slide
out at a slight upward angle ... reinstall in the reverse manner.
3. Typically, filters have an airflow direction indicator arrow ... always install according to the arrow direction. The
E.A.C. Cell is equipped with a plastic handle which should always face outward.
4. Filters should slide easily into and out of the channels & should fit flush with the front edges of hood ... DO
NOT force.
72
6.02 E.A.C. Filter System Overview
The Electronic Air Cleaning (E.A.C.) system is designed to electrostatically capture and collect fine grease
particulate to remove it from the air stream. Three L.E.D. indicator lights ① on the fryer control panel show
operational status of the E.A.C. system.
System also features a Cleaning Timer that will signal operating personnel when it is time to clean the E.A.C.
Collector Cell. Generally, the cell must be cleaned DAILY to maintain peak performance.
STATUS LIGHTS: 2
[ON] Indicates that the E.A.C. cell is installed,
powered, and operating. This should be the
only LED illuminated when system is operating
normally.
[WASH] Light is ON to indicate:
• Filter cell is not installed or is misaligned. 1
• Collection fins contain excessive amounts
of captured grease residue (dirty).
• Poor connection at the contact plate inside
hood.
• Ionizer wires are missing.
The [WASH] light signals an impending fryer
shutdown. Two (2) minutes after the light IMPORTANT! DO NOT consider (or use) the [WASH] light as a
turns ON, an alarm sounds and heating signal for routine cleaning. Typically, the collection cell must
elements are shutdown. The message “ERROR be cleaned DAILY to ensure optimum performance. See
ALARM ‐ CLEAN THE EAC” will be displayed on Section 6.04, EAC Filter Cell Cleaning.
the upper controller display screen ②. If none of these LED indicators turn ON when the appliance is
[CHECK] Light is ON to indicate: powered up, the EAC system may have an internal failure. A
• Ionizer wire broken & shorted out against call for service may be required.
the cell frame.
• Cell is damaged and has shorted out to ground.
• Collection fins are shorted out because of excessive moisture.
The [CHECK] light signals that system is no longer operating to clean the air, even though the hood &
fryer continue operating and controller does not issue an alarm.
STOP TO DETERMINE CAUSE & DO NOT CONTINUE USING FRYER WHEN [CHECK] LIGHT IS ILLUMINATED!
The following actions may clear an alarm condition:

1. Turn OFF fryer POWER switch.
2. Remove the E.A.C. cell and clean as described in Section 6.04.
3. Inspect cell for broken or missing ionizer wires, bent fins, or other damage. Ionizer wires are replaceable (when
ordering replacements, note length ‐ 20”). Bent fins may be gently straightened by hand ... no fin should touch
an adjacent fin. A cell with excessive damage (broken frame, badly bent, broken insulators, etc) must be
replaced.
4. Inspect the E.A.C. contact board inside hood. Clean away any grease accumulation with a mild degreasing
cleaner and dry thoroughly.
5. Replace filter cell (Section 6.01.2) and restart fryer (Section 4.01.10). If the condition persist, call for service.

73
6.02.1 E.A.C. Filter Cell Cleaning Timer Operation
E.A.C. Cleaning Timer controls are located on the fryer control panel. The timer is programmed to issue a warning
signal, alerting operating personnel that it will soon be necessary to clean the collector cell. If this initial alert is not
acted on, the timer will expire ... fryer is shutdown and prevented from continued operation until cleaning is
performed. To avoid this possibility, Giles’ “best practice” recommendation is to routinely clean the collection cell
DAILY, instead of waiting for the timer to expire.
① CHANGE SOON
The amber indicator turns ON when the Timer enters [WARNING] mode. If the collector cell is cleaned
within the next 24 hours, timer automatically resets, a fresh countdown begins, and normal operation
continues without interruption.
② CHANGE NOW 1
The red indicator turns ON when the Timer enters [TIMEOUT] mode to
signal that allowed time between cell cleanings has expired. Alarm 3
sounds and the appliance is turned OFF. It will remain locked out from
continued operation until the cell is cleaned, or replaced with a 2
previously cleaned standby cell.
Placing the POWER switch in the [OFF] position silences the alarm, but appliance will not restart until the
timer is reset by cleaning activities.
③ SNOOZE
The SNOOZE feature is provided in the event that [TIMEOUT] occurred during a period of high customer
demand, or in the middle of a cooking cycle. Pressing the SNOOZE button temporarily returns the Timer
to [WARNING] mode for a period of 2 hours, allowing continued operation.
Only two (2) SNOOZE periods can be used. During the second period, the CHANGE SOON light will blink
on/off to indicate that timer is in the final snooze period. After the second snooze period expires, the
appliance will be lockedout and cannot be restarted until cleaning activities are performed ... refer to
Section 6.04.
74
6.03 Baffle Filter Cleaning
The Baffle Filter is fabricated from thin guage, stainless steel, sheet metal that might
present sharp exposed edges, which can cause cuts if handled improperly ... use due
caution when handling and cleaning. Wearing heavy duty rubber gloves is advised.
Generally, the Baffle Filter should be cleaned daily. Wash filter in sink with a mild degreasing cleaner and warm
water. Rinse and dry completely. Filter must be completely dry before re‐installing in hood. Never place a wet
(or partially dry) filter into hood for operation!
Generally, a baffle filter can be washed in a dishwasher.
6.04 E.A.C. Filter Cell Cleaning
The collector cell contains parts fabricated from thin gauge sheet metal that can potentially
have sharp edges, which can cause cuts if not handled properly. To avoid injury, exercise due
care when handling and cleaning the cell. Wear heavy‐duty rubber gloves as a precaution
against injury.
The E.A.C. collector cell is sustainable and renewable ... it should last for years if handled and cleaned properly. To
maintain peak performance, it MUST BE CLEANED DAILY. Failure to do this can lead to an interruption of appliance
operation, premature failure of the electronic cleaning system, or reduced useful life of consumable charcoal filters.
Follow the procedures detailed below to clean effectively.
IMPORTANT: Collector cell CANNOT withstand washing in commercial dishwashing equipment. Additionally,
some commercial cleaners/detergents will cause oxidation, or contaminate the aluminum collection fins, which
can lead to system malfunction, interruptions in cooking operations, and on‐going system problems.
The following two (2) cleaning methods are endorsed by GILES Food Service:
• Preferred spray foam method uses Simple Green® Crystal Foaming Spray Cleaner/Degreaser. A readily
available foaming aerosol that is an exceptionally effective degreasing cleaner, as well as being safe for use on
aluminum (NSF approved, foodgrade, nontoxic, and biodegradable). Cleaning is quick and easy with this
convenient readytouse cleaner. A complimentary sample is supplied with new equipment ... cleaner can be
ordered from Giles’ dealers/distributors, item #41510 (12‐count case). When used as directed, a case of cleaner
should last approximately 4 to 5 weeks.
• Alternative soaking method ‐ uses diluted solution of Simple Green® Pro‐HD and water. This method is not as
convenient as the spray cleaner, requiring more planning and time, but the procedure has proven to be very
satisfactory for cleaning collector cells for many years. This product has the same characteristics of the spray
product, but requires mixing with water before use ... dilution factor is 1:12, e.g. mix 1/2 gal. of cleaner with 6
gals. of water.
With proper care, cleaning, and handling, the E.A.C. collector cell is designed to provide years of service.
If possible, it is advisable to have a second collector cell which can be cleaned & dried “offline”, then be available
to exchanged for a “dirty” cell on a daily basis.

75
6.04 E.A.C. Filter Cell Cleaning − continued
While handling and cleaning the cell, take care not to bend the collection fins or break any
of the fine ionizer wires that are stretched across the face of the cell. Bent fins and
broken/missing wires can prevent the electronic collection system from performing properly. System faults and
alarms may occur that can potentially interrupt appliance operation.
Ionizer Wire
Fin (9) required
Damage from abusive handling and/or improper maintenance may not be covered by the factory warranty.
A. Preferred Cleaning Method − Spray Cleaner

1. Remove collector cell from hood (see Section 6.01.2) and lay on a
drain board, or other suitable surface.
2. Holding the can at an appropriate distance, spray Simple
Green® Crystal Foaming Degreaser onto the cell.
Completely cover all surfaces ... collection fins, contact plate,
brass fittings and inside corners of frame. Turn cell over and
apply to the other side in like manner, ensuring that both
sides of all the fins are completely covered with the foam.
3. Allow foam to soak for 5 to 10 minutes. In cases of extreme
buildup, a second application may be required after rinsing.
4. Carefully move cell to sink and rinse thoroughly, using hot water spray. Spray ONLY, DO NOT
scrub with brushes.
5. Stand cell upright on a drain board, w/contact plate up ... allow it to drain and air dry overnight.
The cell must be completely dry before being replaced in hood unit. A small electric fan can be
placed to blow across the cell to help expedite drying.
6. Before replacing cell in the hood, inspect for broken/missing ionizer wires and bent fins.
Broken or missing wires need to be replaced promptly. Bent fins may be straightened by hand
so that no fins are touching adjacent fins.
IMPORTANT! ONLY Simple Green® Crystal Foaming Cleaner/Degreaser is recommended by GILES
for cleaning the E.A.C. cell in this manner. Other spray cleaners can contain corrosive ingredients that may
damage the metal components, causing it to fail or not perform effectively. Such conditions may not be covered
by the factory warranty.

76
6.04 E.A.C. Filter Cell Cleaning − continued
B. Alternate Cleaning Method − Soaking

The factoryrecommended product to use for cleaning the E.A.C. cell in this manner is Simple Green® Pro‐HD. It is
a readily available, biodegradable, nontoxic degreasing cleaner that is safe for use on aluminum. It performs well
to clean the cell when diluted at a 1:12 ratio (e.g. 1/2 gal. cleaner to 6 gals ambient water).
DO NOT use DISHWASHING DETERGENTS or CORROSIVE CLEANERS as they can contain ingredients that may
damage the metal cell components, causing failure or unsatisfactory performance. Such conditions may not be
covered by the factory warranty.
1. Cleaning with this method requires a suitable, leakproof container, such as a tall trash bin, recycle
bin, plastic tote, or the GILES soak tank*. Whatever is used must be large enough to hold the cell
along with enough degreasing solution to completely cover it for soaking, either standing on end,
on edge, or lying flat.
2. Fill container with fresh water to a level that will basically cover the cell. Measure
water as container is filled and note the quantity. Add Simple Green® Pro‐HD in the
ratio of 1:12 to the water (e.g. 8 gals of water would require .67 gals (2 qts+21 ozs) of
degreaser. Stir solution well to mix.
* NOTE: The GILES soak tank (purchased separately, Item# 91123) is specifically designed & sized
for soaking the EAC cell. Use 1/2 gal. of the cleaner & fill to the “FULL” line with clean water.
3. After preparing the proper quantity of degreaser solution, hold cell by the contact plate, the frame, or the
provided handle and carefully place it into the solution. Be sure that cell is fully
submerged.
4. Allow cell to soak for approximately 20 minutes (no more than 30 mins), then lift it and
briefly agitate up & down in the solution to help dislodge grease residue.
5. Carefully remove cell from container and complete cleaning process as explained in Steps 4
thru 6 in the previous section.
NOTE:
The degreasing solution may be used multiple times ... cover container with a suitable cover when not in use to
prevent contamination. Discard and mix a new solution when a greasy film seems to be visible, floating on the
liquid. When soaking, always ensure that solution completely covers the cell ... add some water if needed.
77
6.05 Charcoal Filter Maintenance
The only maintenance required for the Charcoal Filter is to periodically replace it with a new filter. Charcoal Filter
cannot be cleaned and reused ... REPLACE ONLY ... it is a one‐use, consumable item. Never attempt to clean and
reuse ... damage to the equipment can result.
Typical replacement cycle is 30 to 40 days, depending on actual cooking & cleaning activities. Maintaining a diligent
cleaning routine for the EAC collector cell can help increase the useful life of charcoal filters.
Replacement Charcoal Filter Giles Item No. 31963 ... available through dealers, distributors and parts suppliers.
Failure to use Giles OEM Replacement Parts and Filters may void the factory warranty.
IMPORTANT!
Attempting to use a charcoal filter for too long a time can cause a CLOGGED FILTER airflow alarm, indicating that
hood capture performance has fallen below minimum requirements. This will cause the fryer heating elements
to be shut‐down until the situation is corrected ... refer to Section 6.01.11.
78
6.06 Filter Alarm Chart
The following table explains the various alarms which may occur due to filter conditions. When an alarm condition
occurs, an audible alarm sounds, an error code is displayed on the lower controller display and an error description
is shown on the upper controller display. Refer to Section 4.01.11 for more information.
OLED
Upper Display
7‐Segment
Lower Display
EAC Status
Lights
Error Message Filter

What will happen Cause Solution See Section
[Error Code] Affected
● Continuous tone alarm.

ERROR ALARM ‐ BAFFLE The filter is not Install filter.
● Power to heating elements is
FILTER MISSING Baffle installed, or is Check filter 6.01.2
shutdown.
[Er21] misaligned. alignment.
● Hood fan continues running
ERROR ALARM ‐ ● Continuous tone alarm.

The filter is not Install filter.
CHARCOAL FILTER ● Power to heating elements is
Charcoal installed, or is Check filter 6.01.2
MISSING shutdown.
misaligned. alignment.
[Er22] ● Hood fan continues running
Airflow Replace charcoal

restriction is filter, about every
● Continuous tone alarm.
ERROR ALARM ‐ present. 30 days.
● Power to heating elements is Charcoal or
CLOGGED FILTER charcoal or baffle Clean baffle filter. 6.03 & 6.05
shutdown. Baffle
[Er23] filter clogged. Check for other
● Hood fan continues running
Other possible airflow
restrictions. restrictions.
Collector cell is
● Continuous tone alarm dirty. Clean EAC cell
ERROR ALARM ‐ CLEAN
● Power to heating elements is Cell not installed. Install cell
THE EAC E.A.C.
shutdown after 2 mins. Contacts dirty. properly. 6.04
[Er24]
● Hood fan continues running Other fault
conditions.
79
6.07 Hood Maintenance
The following section describes the periodic maintenance requirements for the ventless hood system of the GBF50
VH fryer. These activities are vital in maintaining continuing hood efficiency.
Code officials in some jurisdictions may require that permanent record of inspection and maintenance activities be
kept and available for inspection. A sample template for a Maintenance & Service Log is shown in Section 6.07.6.
6.07.1 Monthly Hood Interlock Testing

The hood system features various interlocks which help to ensure that the appliance operates safely and effectively.
Inspection and testing of these interlocks should be performed MONTHLY as described below. Record completion of
these inspections in a permanent log (see Section 6.07.6). If results described below are not observed or other
problems are detected, contact a Giles authorized kitchen equipment service company to have the appliance evaluated
and repaired, or call Giles Technical Services @ 800.554.4537 for further assistance.
During the following processes, be aware that each time you are instructed to turn fryer power OFF and back ON, the
appliance will go through the powerup sequence ... refer to Section 4.01.10, Power Up Procedure.
1. Baffle Filter: Place POWER & HEAT switches in the [OFF] position, remove access cover and the baffle filter
(Section 6.02) ... replace cover. Turn ON power ... leave the HEAT switch in [OFF]. After powerup, a
constant tone alarm should sound, and the upper controller display screen should read “ERROR ALARM ‐
BAFFLE FILTER MISSING”. Place HEAT switch in [HEAT] position & check the amber HEAT light on control
panel ... it should NOT turn ON. Return HEAT switch to [OFF] & turn power OFF ... reinstall the baffle filter.
2. E.A.C. Filter: Remove the EAC Cell (Section 6.02) and replace access cover. Turn ON power ... leave HEAT
switch in [OFF]. After powerup, the ON & WASH status LED’s will turn ON. Wait approximately two (2)
minutes, a constant tone alarm should sound, and the upper controller display screen should read “ERROR
ALARM ‐ CLEAN THE EAC”. Place HEAT switch in [HEAT] position & check the amber HEAT light on control
panel ... it should NOT turn ON. Return HEAT switch to [OFF] & turn power OFF ... reinstall the EAC cell.
3. Charcoal Filter Check: Remove the Charcoal Filter (Section 7.02) and replace access cover. Turn ON power
... leave HEAT switch in [OFF]. After powerup, a constant tone alarm should sound, and the upper controller
display screen should read “ERROR ALARM ‐ CHARCOAL FILTER MISSING”. Place HEAT switch in [HEAT]
position & check the amber HEAT light on control panel ... it should NOT turn ON. Return HEAT switch to
[OFF] & turn power OFF ... reinstall the charcoal filter.
4. Filter Clogged Test: Turn ON power ... leave HEAT switch in [OFF]. After powerup and the hood fan starts,
position a piece of filter paper, or other suitable material, cut to size so as the cover and seal off the entire
area of the baffle filter. After several seconds, a constant tone alarm should sound and the upper controller
display screen should read “ERROR ALARM ‐ CLOGGED FILTER”. Place HEAT switch in [HEAT] position &
check the amber HEAT light on control panel ... it should NOT turn ON. Return all switches to [OFF] position
and remove the blockage material.
5. Access Cover: Turn ON power. Wait for controller to powerup and hood blower to start running. Unlatch
and lift front of access cover away from hood. The appliance should shutdown completely.
80
6.07.2 Quarterly Hood Cleaning
Disconnect supply power to the appliance at the main electrical panel. Blower Wheel
Remove Filter Access Cover and all of the filters. Using a degreasing spray
cleaner, such as Simple Green® Crystal Foaming Degreaser, clean the entire
plenum and blower section of the Hood. Recommended frequency for this
cleaning is every three (3) months.
Inspect the blower wheel for grease residue buildup on the vanes and clean
with the degreasing cleaner, if needed.
Ensure that contacts on the EAC Contact Board are clean and free of
excessive buildup.
Contact Board back
wall of plenum
6.07.3 Semi−Annual Fire System Inspection & Service

Inspection, service and maintenance of the Fire Suppression System must be performed by an authorized Ansul® fire
protection equipment service company, having credentials acceptable to local authorities having jurisdiction (AHJ). As a
minimum, field inspection of the system shall be performed semi‐annually (every 6 months). Such inspection shall
consist of the following.
Place locking bar on the extinguisher system when servicing.

1. Remove charging cartridge and inspect condition of the gasket, recoat with extreme temperature grease, and
reinstall cartridge. See Section 2.08. Fusible Link Detector and Gas Cartridge Locations
2. Remove tank, verify suppressant chemical is at proper level. Clean and coat oring with extreme temperature
grease, and reinstall. See Section 2.09. Fire Extinguisher Nozzle and Tank Locations
3. Check discharge nozzles for signs of grease buildup; clean as needed. Inspect blowoff caps; replace if missing
or damaged.
4. Inspect remote manual activation station for function and wear.
5. Install a test link and test the automatic actuation function.
6. Inspect fusible link detectors; clean as needed. See Section 2.08. Fusible Link Detector and Gas Cartridge
Locations
7. Inspect wire rope for wear at pulleys and detectors; replace as needed.
8. Tag system; record maintenance date and log the inspection in a permanent file.
6.07.4 Annual Fire System Inspection & Service

Same as Semi‐Annual Inspection, except for the following:
1. Replace all fusible links. See Section 2.08. Fusible Link Detector and Gas Cartridge Locations.
81
6.07.5 12−Year Fire System Inspection & Service
Same as Semi‐Annual and Annual except for the following:

1. Replace the wet chemical suppressant storage tank and gas cartridge with components having current
hydrostatic testing certifications.
2. Refill storage tank with fresh wet chemical fire suppressant.
3. Flow test the regulator.
82
6.07.6 Maintenance & Service Log
Check Initial/Date Check Initial/Date

1 2 3 4 1/15/10 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 1 2 3 4 5 6*
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 7* 1 2 3 4 5 6* 7*
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 1 2 3 4 5 6*
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 7* 1 2 3 4 5 6* 7*
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 1 2 3 4 5 6*
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 1 2 3 4 5
1 2 3 4 1 2 3 4
1 2 3 4 1 2 3 4
1 2 3 4 5 6* 7* 1 2 3 4 5 6* 7*
1 Baffle Filter Check 2 EAC Filter Check 3 Charcoal Filter Check

4 Filter Clogged Check 5 Quarterly Cleaning 6 Semiannual Fire System
7 Annual Fire System Insp
* Inspection must be by certified fire equipment service company.
83
84
Troubleshooting GBF−50−VH Electric Fryer
7. Troubleshooting
IMPORTANT! This section describes basic troubleshooting procedures for the GBF50VH electric ventless fryer. General
operational issues may be corrected by users ... more detailed and electrical troubleshooting & repair should be performed
only by qualified kitchen equipment service personnel.
7.01 Temperature Control

Problem Possible Cause Corrective Action
Appliance WILL NOT turn ON: Check for blown fuses or tripped circuit
A. No power being supplied to appliance
• Green POWER light not ON breakers at main electrical panel.
• Hood fan not running
B. Blown appliance fuse or faulty fuse Check fuses inside cabinet, replace if
holder needed. Inspect fuse holders for cracks.
C. Filter access cover not closed & Close & latch cover, be sure cover is
latched properly. resting flat against the hood front.
D. Power switch is faulty Inspect & test, replace switch if needed.
E. Ansul fire extinguisher system is not

Contact Ansul agent for service
cocked & armed
Perform cleaning activities as described
F. EAC Cleaning Timer has timed out &
in Section 6.04, or press control panel
shutdown the appliance ... refer to
SNOOZE button to add 2 hrs of operating
Section 6.02.1
time.
Fryer NOT heating:
• Green POWER light is ON A. HEAT switch not in the [HEAT] position Place switch into [HEAT] position
• Amber HEAT light is OFF
Fryer NOT heating: Oil may be HOT ... check setting. Press
A. Cooking oil temperature setpoint is
• Green POWER light is ON TEMP key twice to display actual temp.
less than actual oil temperature
• HEAT switch is in [HEAT] position HEAT light will cycle ON/OFF.
• Amber HEAT Light is OFF B. “DRAIN OPEN” error ... alarm
• Error code/message may be displayed on Fully close valve to reset error
sounding
controller screens
C. Controller is faulty Call for service, check/replace controller
D. Temperature sensor faulty ...error Call for service, inspect & replace sensor,
Er13 if needed
Call for service; inspect & replace
E. Faulty contactor
contactor, if needed
Call for service; inspect, test & replace
F. Faulty HEAT switch
switch, if needed
G. Powerup procedure not completed,
Press [START] key to begin PREHEAT
[START] key not pressed
Fryer NOT heating:
• Green POWER light is ON
• HEAT switch is in [HEAT] position A. If equipped, circuit breaker on rear of Remove access cover, check & reset
• Amber HEAT light is ON fryer cabinet is tripped. breaker, if needed
85
GBF−50−VH Electric Fryer Troubleshooting
7.01 Temperature Control − continued
Fryer NOT heating: Inspect filter installation ... try
A. Baffle filter missing or misaligned
• Green POWER light is ON removing and reinstalling
• HEAT switch in [HEAT] position
• Alarm sounding Inspect filter installation ... try
“FILTER MISSING” message B. Charcoal filter missing or misaligned
removing and reinstalling
displayed on controller screen
Fryer NOT heating:
A. EAC collector is excessively dirty Clean the EAC collector cell
• Green POWER light is ON
• HEAT switch is in [HEAT] position B. EAC cell has too many broken
• Amber HEAT light is OFF Replace ionizer wires
ionizer wires
• Alarm sounding
• “CLEAN THE EAC” message C. Poor connection with contact board
Clean contacts, or replace board
displayed on controller screen ... dirty or damaged
• EAC WASH light is ON
D. Faulty EAC power supply Call for service
E. EAC shutdown module is faulty Call for service
F. EAC cell is missing Install or reinstall collector cell
Fryer cooling NOT heating: Cycle power ... turn OFF for approx. 5
A. Power surge
• Green POWER light is ON secs, then ON
• HEAT switch is in [HEAT] B. Low oil level Check level, add oil as needed
position
• Red HILIMIT light is ON Call for service, check/replace
C. Contactor sticking
contactor
Call for service, check/replace High
D. Faulty high‐limit safety thermostat
Limit Board
E. Faulty high‐limit sensor or sensor Call for service, test/adjust, or replace

out of position sensor
F. Faulty controller Call for service. test/replace controller
Fryer NOT heating:

• Green POWER light is ON Replace charcoal filter ... DO NOT TRY
A. Charcoal filter clogged
• HEAT switch is in [HEAT] TO CLEAN
position
B. Vacuum switch needs adjustment, Call for service, adjust switch or
• Amber HEAT light is OFF
or is faulty replace, if needed
• Alarm sounding
• “CLOGGED FILTER” message C. Vacuum lines clogged or kinked Inspect tubing, clean or remove kinks
displayed on controller
D. Fan running too slow Call for service, check voltage
E. Fan clogged with grease film Clean fan & hood plenum
F. Exhaust vent on hood top blocked Inspect, clear any obstructions
86
7.01 Temperature Control − continued
Fryer heating slowly: Consult Operations Manual for proper
A. Improper cooking procedures
• Slow heat recovery procedures
• HEAT light remains ON constantly B. One or more heating elements Call for service ... Inspect & test,
faulty replace faulty element(s)
Call for service ... Test, replace
C. Contactor failing
contactor if needed
D. Loose wiring Call for service ... Inspect & repair
E. Low incoming voltage Call for service ... check supply power
Fryer heating slowly:
A. Low incoming voltage Call for service ... check supply power
• Short cycling, HEAT light turning
ON & OFF continuously B. Variable temperature sensor Call for service ... check location,
positioned to close to an element correct as needed
Call for service ... test & replace
C. Faulty controller
controller if needed
Oil temperature is erratic: Call for service ... test & replace probe
A. Faulty temperature sensor
if needed
Call for service ... Test, replace
B. Contactor is failing
contactor it needed
Call for service ... test & replace
C. Faulty controller
controller if needed
D. Loose wiring Call for service ... Inspect & repair
Oil is smoking: A. Oil breaking down ... too old Replace oil in fryer with fresh
Check controller setpoint, verify

B. Cooking at excessive temperatures
cooking procedures, adjust as needed
C. Dirty heating elements Perform boilout, clean vat & elements

Call for service ... test & replace as
D. Faulty heating element
needed
Call for service ... verify incoming
E. Improper supply voltage
power supply
Maintain oil level between the ADD &

F. Low oil level
FULL marks at all times
87
GBF−50−VH Electric Fryer Troubleshooting
7.02 Oil Filtration System
Problem Probable Cause Corrective Action
Oil NOT pumping back to vat: A. PUMP switch not in [PUMP] Switch must be placed in [PUMP]
position position to pump oil
B. Air leaking into the system
Inspect pan & connections, be sure
plumbing (hose, fitting, connector,
coupling connection is secure,
filter pan, etc)
Call for service ... Test motor, replace
C. Pump motor faulty
if needed
Call for service ... disassemble pump
D. Filter pump clogged, or damaged head, inspect, clean or replace if
needed
E. Excessive sludge or crumbs
Clean filter pan, refresh filter media
accumulated in the filter pan
F. Pump diverter valve not set to [OIL Place valve handle in the proper
RETURN] position position
Manually remove oil from filter pan &
G. Oil too cold (thick) to pump
clean
Oil pump bound up: A. Boilout solution or water has been
Disassemble pump head, clean & oil
pumped through pump
B. Oil has hardened in pump or
Disassemble pump head & clean
plumbing ... sat too long
C. Large cooking debris/crumbs
Disassemble pump head & clean
ingested into pump
7.03 Basket Lift System (if equipped)

Basket Lift will not operate. A. LIFT switch on control panel is in the Place switch in [LIFT] position to
[OFF] position. enable lifts.
Lifts cannot be operated manually until
B. Fryer is in PREHEAT mode. cooking temp has been reached &
controller is in READY state.
Refer to Operation Manual for
C. Not following proper procedure.
instructions.
D. Controller has failed, no output
Call for service.
voltage to lift.
E. Basket lift microswitch is out of
Call for service.
adjustment or faulty.
G. Basket lift motor or gearbox has
Call for service.
locked up.
88
7.05 Basket Lift System (if equipped) − continued
Lift moves very slowly, struggles to
A. Motor brake is stuck, not releasing. Call for service.
raise.
B. Motor or gearbox is beginning to
Call for service.
fail.
Lift vibrates or chatters excessively A. Lift mechanism out of alignment,
when running. parts broken/failing, motor brake Call for service.
sticking or gearbox is failing
Basket Lift will not remain in raised
A. Lift motor brake has failed or is
position ... drifts down. Call for service.
failing, not fully engaging.
89
90
Parts List GBF−50−VH Electric Fryer
8. Parts List
This section lists the various parts that are available for field replacement on the unit. This is not an all inclusive
listing; please contact an authorized Giles representative or service agent concerning other parts that may be
replaced in the field.
8.01 Ordering & Service Information

Giles is an equipment manufacturer and does not sell service parts direct. Parts for Giles equipment are available
through authorized service agents, part distributors, and/or kitchen equipment dealers. If assistance sourcing parts
or obtaining equipment repair service is required, please contact a GILES’ representative for information concerning
authorized sources near you. For further assistance you may contact GILES Services Support as follows:
UNITED STATES & CANADA call: 800.554.4537

ALL OTHERS call: 334.272.1457
Normal business hours are 8:00 AM to 5:00 PM Central Time ... calls are answered by an automated answering
system ... please follow the recorded instructions to reach the desired department or individual.
If calling outside of normal hours, leave a voicemail message along with an appropriate contact number and a
Services representative will return the call as soon as possible, usually within thirty (30) minutes ... representatives
will be available 24/7/365.
Website: www.gfse.com or email services@gfse.com.
Our goal at Giles is to provide the highest possible quality of service and assistance. To help us accomplish this,
please have the following information readily available when calling, along with a brief description of the problem
being experienced. Please record the unit information in the table below for quick reference.
Model:
Serial Number:
Voltage/Phase:
The information can be

found on the
serial/data label located
inside the cabinet or on
a rear cabinet panel.
91
GBF−50−VH Electric Fryer Parts List
8.02 Control Panel
7 1
13
12 3
14+
3+
15+
11 10 9 2 6
3 8
92
8.02 Control Panel
ITEM PART NO. QTY DESCRIPTION
1 21379 1 CONTROLLER, DUAL TIMER, COMPUTER
2 21190 1 SWITCH, ROCKER, ONOFF, 250V, 20A, DPST
3 21052 2 or 3+ SWITCH, ROCKER ,ONOFFON, 250V, 20A, DPDT (3rd switch only when equipped w/lifts)
4 20398 1 INDICATOR LIGHT, GREEN, 250VAC (Requires #20307, RETAINING CLIP)
5 20399 1 INDICATOR LIGHT, ORANGE, 250VAC (Requires #20307, RETAINING CLIP)
6 20402 1 INDICATOR LIGHT, RED, 250VAC (Requires #20307, RETAINING CLIP)
7 66300 1 LABEL, CONTROL PANEL, GBF50VH
8 24209 1 L.E.D. LIGHT CLUSTER
9 20694 1 PILOT LIGHT, YELLOW, EAC TIMER
10 20693 1 PILOT LIGHT, RED, EAC TIMER
11 20692 1 SWITCH, MOMENTARY PUSHBUTTON, EAC TIMER
12 30238 1 MANUAL PULL, MODIFIED (ANSUL)
13 46707 1 BREAK ROD (ANSUL)
14+ 20621 1 PLUG, SWITCH CUTOUT (USED WHEN NO LIFTS INSTALLED)
15+ 41454 1 GASKET, CARLING SWITCH (USED WHEN NO LIFTS INSTALLED)
+ Switch position plugged using items #14 & #15 when not equipped with basket lift option.
93
8.03 Control Assembly − Front
Front control assembly located behind the Control Panel
1
5
11 9 8
10
94
8.03 Control Assembly − Front
1 21592 1 LIMIT CONTROL, SAFETY, 450DEG F, DUAL
2 21203 3 RELAY, SPSTNONC, 240VAC
3 21509 1 DIST.BLOCK, 12PL, 1226 AWG, RED
4 21510 1 DIST.BLOCK, 12PL, 1226 AWG, BLACK
5 21496 2 END BRKT CLIP, DIN RAIL, PTFIX, NS35
6 94784 1 RAIL, DIN, 3IN
7 20572 1 GMT, EAC TIMER, BOARD
8 22976 1 AUDIOLARM, CONTINUOUS, 212 VDC
9 21950 2 HOLDER, FUSE, 300V, 15A, SC 0 TO 15
10 21900 2 FUSE, 15AMP, SC15
11 20366 1 TRANSFORMER, 20VA, 115/230V, 60HZ, CL2
95
8.04 Lower Cabinet − Front
2 7 6
5
12
●
11
9 4
10
8
1 13
Rear of brace
14
96
8.04 Lower Cabinet − Front

1 45755 1 DIVERTER VALVE, 3WAY, 1/2NPT
2 92784 1 DRAIN VALVE HANDLE ASSEMBLY
3 21157 1 DRAIN VALVE INTERLOCK, LIMIT SWITCH, 15A, 250V,
4 21164 1 TERMINAL BLOCK, POWER DISTRIBUTION
5 21051 1 GROUND LUG
6 92766 1 COVER, ELECTRICAL SERVICE ENTRANCE BOX (Requires a new label [#7] when replaced)
7 65630 1 LABEL, SERVICE ENTRANCE BOX
8 92627 1 COMPLETE FILTER PAN ASSEMBLY w/COVER (Refer to Section 8.09 for detail)
9 92787 1 DOOR ASSEMBLY
10 41900 1 QUICKCOUPLING, FEMALE, FILTER PAN
11 41699 1 QUICKCOUPLING, FEMALE, DISCHARGE HOSE
12 65673 1 LABEL, FRONT BRACE, GBF
13 40909 1 HOSE, CORRUGATED, SS, 1/2 NPT X 15
12 40889 VAR. ADAPTER, 1/2COMPRESS TO 1/2NPT (Used for all flex tube to hard pipe connections)
97
8.05 Lower Cabinet − Rear
2 7
4 3
8 9
13
16
15 14
12* 20
10
17 11* 18
19
* Part of Item #10 (71754).
98
8.05 Lower Cabinet − Rear

1 21245 2 CONTACTOR, 60A RES, 3PL, 100250V COIL
2 20513 1 CIRCUIT BREAKER, 277V, 50A, 6POLE
3 21504 1 DIST.BLOCK, 6PL, 1226 AWG, RED
4 21496 1 END BRKT CLIP, DIN RAIL, PTFIX, NS35
5 98335 2 RAIL, DIN, 2IN
6 94784 1 RAIL, DIN, 3IN
7 40399 1 BUSHING, 3/4”, BLACK NYLON
8 40650 2 CASTER, 5IN, RIGID, PLATE MT. (Rear)
9 40700 2 CASTER, 5IN, SWIVEL, W/BRAKE, PLATE MT. (Front)
10 71754 1 PUMP & MOTOR ASSY, 5GPM, 1/2HP
11* 76923* 1 PUMP HEAD ONLY, 5GPM [PART OF 71754]
12* 71824* 1 PUMP MOTOR ONLY, 1/2HP [PART OF 71754]
13 42200 4 ELBOW, 1/2NPT, 90DEG, BLACK PIPE
14 40176 1 NIPPLE, 1/2NPT X 121/2, BLACK PIPE
16 42250 2 STREET ELL, 1/2NPT, 90DEG, BLACK PIPE
18 43850 1 CLOSE NIPPLE, 1/2NPT, BLACK PIPE
19 45575 1 UNION, 1/2NPT, BLACK PIPE
20 40889 2 ADAPTER, 1/2COMPRESS TO 1/2NPT
* Part of Item #10 (71754).
Hard pipe nipples & fittings are standard 1/2” NPT, Schedule 40, black coated steel
99
8.06 Cook Vat Assembly
3 6
Top View Inside Vat
5 2
6
21 19
7 8
1
Bottom Top
Sensor Sensor
19 22
20
Front of fryer
11 12 13 14
Bottom View of Vat
15
18
16 17
9 10
Front of fryer
100
8.06 Cooking Vat Assembly

20563 2 ELEMENT, 208V, 9000W, FIREBAR (FOR 18kW MODEL)
1
2 21596* 1 THERMOCOUPLE J, DUAL, UNGRND, 71/2” (HI‐LIMIT PROBE)
3 39972 1 ELEMENT BRACKET, HIGHLIMIT
4 20362* 1 THERMOCOUPLE, JTYPE, UNGRND, 71/2” (ELEMENT TEMP PROBE)
5 39974 1 ELEMENT BRACKET, OIL LEVEL
6 94462 2 STRAP, ELEMENT BRACKET
7 23900* 1 THERMOCOUPLE, JTYPE, 3’, GRND (VAR. TEMP PROBE ‐ BOTTOM)
8 20439* 1 THERMOCOUPLE, JTYPE, 3’, UNGRND (ADD LEVEL PROBE ‐ TOP)
9 45400 4 CONNECTOR, 0.190 ID, 1/4NPT, SWAGELOCK
10 45111 4 FERRULE, SWAGELOCK (PROVIDED w/NEW SWAGELOCK, SEE NOTE)
11 42250 2 STREET ELL, 90DEG, 1/2NPT, BLACK PIPE
12 43850 1 CLOSE NIPPLE, 1/2NPT, BLACK PIPE
13 40296 1 TEE, 1/2NPT, BLACK PIPE
14 41079 1 HOSE, CORRUGATED, SS, 1/2” ID X 8”
15 40889 3 ADAPTER, 1/2COMPRESS TO 1/2NPT
16 41106 1 DRAIN VALVE, 11/2NPT X 11/2” TUBE, SS
17 40820** 1 ORING, DRAIN VALVE, 11/2” [REQUIRED W/DRAIN VALVE]
18 93013 1 DRAIN TUBE ASSEMBLY
19 93324 2 ELEMENT SUPPORT BRACKET
20 98334 1 ELEMENT SUPPORT BAR
21 10532 1 ACORN NUT, 1032, SS
22 40513 2 ELEMENT GASKET
* If not replacing swagelock connector (#45400), a replacement thermocouple requires new swagelock ferrule (#45111).
** Oring (#40820) required w/Drain Valve
Hard pipe nipples & fittings are standard 1/2” NPT, Schedule 40, black coated steel
101
8.07 Ventless Hood & Fryer Front
5
6
Standard No Lift Optional Basket Lifts
9
10
11
8
102
8.07 Ventless Hood & Fryer Front

1 98316 1 COVER, FILTER ACCESS
2 31963 1 CHARCOAL FILTER ASSEMBLY, 16” X 123/8” X 2”
3 93305 1 E.A.C. COLLECTOR CELL w/HANDLE & PLATE, 16”
4 41491 1 BAFFLE FILTER, 121/2” X 201/4” X 13/4”, SS
5 30206 1 GREASE DRIP CATCH CUP
6 34750 1 DRIP CUP SECURITY CLIP
7 41040 2 COOK BASKET, AW8, 131/4” X 61/2” X 6”
8 41041 1 FRY SCREEN/BASKET SUPPORT
9 35088 2 SUPPORT BAR, BASKET HANGER RACK
10 92805 2 ROD, BASKET HANGER RACK
11 95025* 2 BASKET LIFT CARRIER ASSEMBLY (OPTIONAL)
* Optional configuration
103
8.08 Ventless Hood Components − Rear
18
3
18
2 4* 1
20
19
18
19
21
6 5
22
20 8
23
7 11
12
13 14
20
9
10
17 15 16
15
* Not shown
104
8.08 Ventless Hood − Rear

1 93296 1 BLOWER ASSEMBLY
2 98345 1 COVER, HOOD TOP
3 97376 1 AIR DIVERTER
4* 41115 1 FIRE DAMPER, 10” X 10” X 21/4”, 285°F FUSIBLE LINK
5 21296 1 EAC POWER SUPPLY, 120V [w/DRIVER BOARD & JUMPER]
6 21203 2 RELAY, SPSTNONC, 240VAC
7 23776 1 SHUTDOWN/ALARM MODULE, AIR FILTER
8 21337 1 TRANSFORMER, 230VAC to 115VAC @.86A [EAC POWER SUPPLY]
9 21101 1 RELAY SOCKET, 8PIN, 300V, 10A
10 21102 1 RELAY, 8PIN, 240V, 10A
11 94784 1 DIN RAIL, 3”
12 21496 2 END BRACKET CLIP, DIN RAIL, PTFIX NS35
13 21509 1 DISTRIBUTION BLOCK, 12POLE, 1226 AWG, RED
14 21510 1 DISTRIBUTION BLOCK, 12POLE, 1226 AWG, BLACK
15 20390 1 VACUUM SWITCH, 0.16 1.20 WC [DUNGS]
16 40880 1 NYLON FITTING, 90° ELL, 1/4NPT, BARBED
17 40877 1 NYLON FITTING, 90° ELL, 1/8NPT, BARBED
18 21502 3 SENSOR, PROXIMITY, INDUCTIVE, 24240V
19 21125 1 CONTACT BOARD, E.A.C.
20 98398 4 ACCESS COVER, SMALL, 31/2” X 41/2”
21 40132+ 1 MECHANICAL RELEASE, ANSUL AUTOMAN
22 40811+ 1 TANK, 1.5GAL, SS, WET CHEMICAL FIRE SUPPRESSANT
23 21429 1 POWER SUPPLY, AC/DC, 24VDC, 60W, L.E.D. LIGHT
* Not shown
+ All components of the fire system must be serviced or replaced only by authorized Ansul service agents
105
8.09 Ventless Hood Components − Filter Compartment
1 3
10 1
2
1
4
L.E.D. Hood Light Assembly
106
8.09 Ventless Hood − Filter Compartment

1 21502 3 SENSOR, PROXIMITY, INDUCTIVE, 24240V
2 21125 1 CONTACT BOARD, E.A.C.
3 98357 1 COVER, PROXIMITY SWITCH
4 98941 1 BRACKET, FIRE SUPPRESSION PIPE
5 98503 1 MOUNT, L.E.D. HOOD LIGHT
6 98502 1 L.E.D. STRIP LIGHT, 10” w/WIRE LEADS & ADHESIVE BACKING
7 41507 1 LENS, L.E.D. HOOD LIGHT, PLEXIGLASS
8 98506 1 COVER, L.E.D. HOOD LIGHT
9 41117 1 GASKET, PSHAPED, 3/8 x 3/4 x 1211/16”
10 98317 1 BRACKET, GASKET
107
8.10 Filter Pan
2+
1
3
[A]
6 7
8 9
10
108
8.10 Filter Pan

1 92623 1 HOLDDOWN FRAME
2* 65781* 1 FILTER PAPER MEDIA; PAN REQUIRES (1) SHEET (Supplied as Case of 100 Sheets)
3 41078 1 FILTER SCREEN, REUSABLE, STAINLESS STEEL, MICROMESH (STANDARD)
4 40649 4 SWIVEL CASTER, 21/5”, PLATE MOUNT
5 41073 2 HOSE, 1/2 NPT x 121/2” FLEX w/SWIVEL FITTINGS (Bottom Hose not seen)
6 38841 4 HOLDDOWN FRAME LOCKING HANDLE
7 300404 4 STUD, HOLDDOWN FRAME LOCKING HANDLE
8 95378 1 FILTER PAN COVER
9 44150 1 QUICKCOUPLING, MALE, BRASS
10 92627 1 COMPLETE FILTER PAN ASSEMBLY (INCLUDES ITEMS 1, 3, 4, 5, 6, 7, 8 & 9)
* Optional alternative
Note [A]: The perforated plate in the filter pan bottom is NOT a filter! It ONLY serves as the filter media support and
safeguards against allowing excessively large crumbs or debris from unintentionally entering the filtration system.
Filter media must be used for filtering oil. Failure to utilize proper filter media will void the warranty! This plate is
NOT a replaceable part.
109
110
Appendix GBF−50−VH Electric Fryer
A. Connecting Optional KITCHENTRAC ™

If you purchased a new Giles cooking appliance with the factory
equipped, optional KitchenTrac™ Remote Monitoring
application, it comes to you WiFi capable and ready for
connection to your local network and the KitchenTrac™ server.
The app provides remote monitoring of your cooking equipment
performance, productivity, menu trends, maintenance events
and offers a multitude of other analytics pertaining to your food
service operation.
Use of the application requires a small monthly server hosting fee for each controller monitored, but the benefits
will pay for it over and over.
The WiFi Connection Manual, Form #66313 was shipped with your new equipment ... the following information also
describes the process to connect each controller (fryer) to the KitchenTrac™ server. After equipment is installed
and checked out, follow these instructions precisely and get connected to begin experiencing the benefits of remote
performance monitoring.
Should you encounter any difficulties with the process, please contact GILES Technical Services @ 800.554.4537 or
email services@gfse.com.
A.1 Connecting WiFi Board to Wireless Router

3 5 There are minor differences in control panel layout &
1 configuration between appliance models.
IMPORTANT! There must be a continuous

connection to the internet with a wireless WiFi
router, which is within range of the monitored
equipment. The password for the establishment
6 4 2 router may be required.
1. Place POWER switch ① [ON] ... controller powersup ... alarm should sound ... press [ALARM] key ⑥ to
silence. Be sure to keep SELECTOR or HEAT switch ② in the [OFF] position throughout the process to prevent
heating elements from energizing.
2. Press [TIME] key ③ + 9 4 3 4 on keypad + [START] ④.
Message “WiFi Setup PRESS [START]” appears on the upper display screen ⑤ ... press [START] key.
3. The message “SEARCHING FOR WIFI MODULE” will appear on screen.
If WiFi module is not found within 10 seconds, message “COMMUNICATIONS ERROR, CHECK CONNECTIONS”
will be displayed. Several issues can cause this error ... DIP switches are not set properly, cable is disconnected,
jumpers are missing, etc.
Turn power switch OFF ... check switches, jumpers and connections and retry. If the error persist, call Giles
Technical Services @ 800.554.4537 for assistance.
4. If module is successfully found, message “WIFI MODULE FOUND, CONFIGURING” appears on screen.

111
GBF−50−VH Electric Fryer Appendix
A.1 Connecting WiFi Board to the Wireless Router − continued
5. The display will cycle through the messages shown below as the configuration process continues:
• “WIFI MODULE FOUND, GETTING STATUS”
• “STARTING CONFIG PORTAL”
• “PORTAL ENABLED, CONNECT TO WIFI”
6. When “CONNECT TO WIFI” appears ... open WiFi Settings on a
smartphone [Android or iPhone] to display available networks
... select KitchenTrac_Config. This is the network being
broadcast by fryer’s WiFi board for setup purposes.
You will be prompted to enter a password ... password is kitchentrac (all lowercase).
7. The phone should open a captive portal.
NOTE: If the captive portal does not automatically open after about 30 seconds, open the phone’s web
browser and type the IP address 10.10.0.1 & enter.
8. On the phone, select the establishment’s WiFi network to which you are attempting to connect. Enter the
router password (if necessary), then tap the “Join” button.
A.2 Establishing Communication with KitchenTrac™

1. A “pair code” must be communicated to GILES Tech Service while the person performing the connection
procedure is still onsite and has access to the unit.
If the previous steps were successful the “pair code” should be displayed on the fryer controller screen. This
code regenerates randomly every 15 minutes to a different value, so whatever code is displayed while in
contact with Giles Services is the one that must be registered before monitoring can begin.
If “pair code” does not appear, go to step #2 of Section A.1 and try connecting again.
When you have acquired the code, call GILES Tech Service @ 800.554.4537 and communicate the displayed
code to the Tech Service representative, who will then enter it into the KitchenTrac™ website.
2. If the “pair code” did not appear during Step #1 above, you might try viewing the “WIFI SYSTEM LOG” on the
fryer controller screen to acquire it.
• Press [TIME] + 7 7 7 7 + [START] on controller.
• Press keypad right arrow key [6>] until “WIFI SYSTEM LOG” displays on upper screen.
• A pair code should be displayed.
• Call GILES Tech Service @ 800.554.4537 and communicate the displayed code to the Tech Service
representative for entering into KitchenTrac™.
3. After pair code has been entered, verify that the controller is actually connected to KitchenTrac™.
To confirm that connection and successful communication has been established, enter controller diagnostics
mode by pressing [TIME] + 7 7 7 7 + [START], then press keypad right arrow key [6>] until upper display shows
Connection Status ... it will show as either “SERVER CONNECTED” or “NOT CONNECTED”.
If communication if has not been established, it is possible that there are problems with internet connectivity at
your location, or the wireless router is possibly not within range of the appliance. Please contact GILES Tech
Service for assistance in resolving the issue.
112
Appendix GBF−50−VH Electric Fryer
A.3 WiFi Components
2 WIFI boards are located in various locations

inside the appliance cabinets. An antenna will
protude from cabinet near its lociation.
IMPORTANT! Take care not to damage the

antenna when cleaning or servicing the
equipment.
1
3
4*

1 21606 1,2 or3 WIFI BOARD ASSY, EXT ANTENNA
2 21613 1,2 or 3 ANTENNA, WIFI, 2.4GHz, RPSMA, 1.8dB
3 21614 1,2 or 3 CABLE, ANTENNA, RF, U.FL TO RPSMA, 15IN
4 21454* 1,2 or 3 CABLE, CONNECTOR, RJ45, PLUGTOPLUG. 6FT
* Not shown connects board to controller.
NOTE: Banked systems have these components in each unit.
113
Giles Enterprises, Inc.
P.O. Box 210247 • 2750 Gunter Park Drive West • Montgomery, Al 361210247 USA
Phone: 334.272.1457 • Toll Free: 800.554.4537 (USA & Canada Only) • Fax: 334.239.4117 • www.gfse.com
Email: services@gfse.com
Form No. 66317 (Rel. Date: Aug.2019; Rev. A)

Oper Manual Gbf-50-Vh

Uploaded by

Copyright:

Available Formats

Oper Manual Gbf-50-Vh

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Oper Manual Gbf-50-Vh

Uploaded by

Copyright:

Available Formats

GBF­50­VH

Operations & Service Manual Ventless Electric Fryer

ISO 9001 Registered • Committed to Quality

Printed in USA, Form No. 66317 (Rel. Date: Aug.2019, Rev. A)

6.02.4 Annual Fire System Inspection & Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Appendix ­ A. Connecting Optional KITCHENTRAC™ . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Specific Safety Precautions:

• The appliance must remain in an upright position.

1.02 Standard Features

1.02.1 Optional Features

1.03.1 Overall Dimensions

1.03.2 Agency Certifications

1.03.3 Basket Specification

INCHES [mm] * Mixed pieces, 3­1/3 lb bird.

1.03.5 Shipping Specifications (Crated)

NOTE: Gross weight approx ... may vary slightly

2.01 Appliance Location

DO NOT MODIFY, ADD ATTACHMENTS OR OTHERWISE ALTER THIS EQUIPMENT

2.03 Electrical Requirements

2.05 Electrical Connections

Main Breaker Service Disconnect Incoming power

2.06 Ventless Hood Clearance

2.08 Fusible Link Detector & Gas Cartridge Locations

All Nozzles = Ansul 1/2N

Fire Alarm Connection:

2.11.1 Power Test

2. Liberally dampen heating

3. After performing Power Test,

2.11.4 Initial Fryer Cleaning

14” Cooking Vat

Item Description Function

Contains product for cooking. Plated wire baskets, 13­1/4” x 6­1/2”

1 Drain Valve Handle Even though safety interlocks are designed

Quick­coupler fitting for connecting the filter pan assembly to the

Item Description Function

Collects grease condensate generated by the baffle filter. Inspect daily

L­ Shaped Brush Use to clean between, around and

Heat­resistant, multi­purpose, use to

Crumb Shovel Use to remove sediment from the

Use to discharge waste cooking oil to

Supports baskets while cooking

Sustainable stainless steel filter

3.07 Accessories Not Provided

A portable oil disposal container with

Paper filter media for use in the filter

Fry Pot Cover Covers fry pot during periods of

4.01.1 Keys and Functions

[CLEAR]: A function key used to cancel processes, exit functions, etc.

Continued on Next Page

4.01.1 Keys and Functions − continued

Upper Display Screen (blue graphic): Displays status information, setting

Lower Display Screen (red graphic): Displays various status information,

Press the [START]

Use keypad to enter a

Use keypad to select which side the

Choose NAME setting as

Use left arrow key [<4] to backspace and erase errors.

When finished, press [START]

Continued on Next Page

GBF50VH

Appendix A. Connecting Optional KITCHENTRAC™ . . . . . . . . . . . . . . . . . . . . . . . . . . 111

INCHES [mm] * Mixed pieces, 31/3 lb bird.

Contains product for cooking. Plated wire baskets, 131/4” x 61/2”

Quickcoupler fitting for connecting the filter pan assembly to the

L Shaped Brush Use to clean between, around and

Heatresistant, multipurpose, use to

Enter desired Menu no. [150].

Use keypad [2] UP [8] DOWN key to select

ER21 BAFFLE FILTER MISSING Baffle Filter in hood is missing or misaligned.

ER22 CHARCOAL FILTER MISSING Charcoal Filter in hood is missing or misaligned.