INR18650 29E Samsung

SAMSUNG SDI Confidential Proprietary
Spec. No. INR18650-29E Version No. 1.1
SPECIFICATIONS OF PRODUCT
1. Customer :BATTEX
2.Product : Lithium-ion Battery
3.SDI Model : INR18650-29E
4. Approved by
Division
Signature
Date / / / / / /
5.Date of Application (YY/MM/DD) : 2012/09/19
6.Supplier : SAMSUNG SDI Co., Ltd.

Energy Business Division
Issued Checked Approved
Hanks Kang Michael Rim

Manager General Manager
CSG CSG
Revision Revision
Page Item Description Remark
No. date
1.0 24/Apr/2012 First Edition
1.1 25/May/2012 3 3. Nominal specifications refined
- Nominal capacity
- Nominal voltage
- Weight max 4548g
Typo corrections
1 Samsung SDI., Battery Business Division.

1. Scope
This product specification has been prepared to specify the rechargeable lithium-ion cell
('cell') to be supplied to the customer by Samsung SDI Co., Ltd.
2. Description and Model

2.1 Description Cell (lithium-ion rechargeable cell)
2.2 Model INR18650-29E
3. Nominal Specifications
Item Specification
3.1. Nominal Capacity 2,850mAh (0.2C, 2.50V discharge)
3.1.1. Typical Capacity 2,850mAh (0.2C, 2.50V discharge)

3.1.2. Minimum Capacity 2,750mAh (0.2C, 2.50V discharge)
3.2. Charging Voltage 4.20 ± 0.05 V
3.3. Nominal Voltage 3.65V (0.2C discharge)
CC-CV
3.4. Charging Method
(constant voltage with limited current)
3.5. Charging Current Standard charge: 1,375mA
3.6. Charging Time Standard charge: 3hours
3.7. Max. Charge Current 2750mA (not for cyclelife)

2,750mAh (continuous discharge)
3.8. Max. Discharge Current
8250mAh (not for continuous discharge)
3.9. Discharge Cut-off Voltage 2.50V
3.10. Cell Weight (max. (g)) 48g

Diameter(max.) : 18.40 mm
3.11. Cell Dimension
Height(max) : 65.00 mm
3.12. Operating Temperature Charge: 0 to 45°C
(Cell Surface Temperature) Discharge: -20 to 60°C
1 year : -20~25°C (1*)
3.13. Storage Temperature 3 months : -20~45°C (1*)
1 month : -20~60°C (1*)
Note (1): If the cell is kept as ex-factory status (50% of charge),
The capacity recovery rate is more than 80%.

4. Outline Dimensions
See the attachment (Fig. 1)
5. Appearance
There shall be no such defects as scratch, rust, discoloration, leakage which

may adversely affect commercial value of the cell.
6. Standard Test Conditions
6.1 Environmental Conditions

Unless otherwise specified, all tests stated in this specification are
conducted at temperature 25±5°C and humidity 65±20%.
6.2 Measuring Equipment

(1) Ammeter and Voltmeter
The ammeter and voltmeter should have an accuracy of the grade 0.5 or higher.
(2) Slide caliper
The slide caliper should have 0.05 mm scale.
(3) Impedance meter
The impedance meter with AC 1kHz should be used.
7. Characteristics
7.1 Standard Charge

This "Standard Charge" means charging the cell with charge current of
1,375mA and constant voltage 4.20V at 25°C, 0.02C cutoff.
7.2 Standard Discharge Capacity

The standard discharge capacity is the initial discharge capacity of the cell, which is
measured with discharge current of 550mA with 2.50V cut-off at 25°C within 1 hour
after the Standard charge.
Standard Discharge Capacity ≥ 2,750mAh
7.3 Rated Discharge Capacity

The rated discharge capacity is the initial discharge capacity of the cell, which is
measured with discharge current of 2,750mA with 2.50V cut-off at 25°C within 1 hour
after the Standard charge.
Rated Discharge Capacity ≥ 2,668mAh (97% of 2,750mAh)
7.4 Initial internal impedance

Initial internal impedance measured at AC 1kHz after Standard charge.
Initial internal impedance ≤ 45mΩ
7.5 Temperature Dependence of Discharge Capacity

Discharge capacity comparison at each temperature, measured with discharge
constant current 2,750mA and 2.50V cut-off with follow temperature after the Standard
charging at 25°C.

Charge Temperature Discharge temperature

25°C -10°C 25°C 40°C
Relative Capacity 60% 97% 97%
Note: If charge temperature and discharge temperature is not the same,

the interval for temperature change is 3 hours.
Percentage as an index of the Standard discharge capacity (=2,750mAh) is
100%.
7.6 Temperature Dependence of Charge Capacity

Capacity comparison at each temperature, measured with discharge
constant current 2750mA and 2.50V cut-off at 25°C after the Standard charge is
as follow temperature.
Charge temperature Discharge temperature

0°C 25°C 45°C
25°C
Relative Capacity 80% 100% 100%
Note: If charge temperature and discharge temperature is not the same,

the interval for temperature change is 3 hours.
Percentage as an index of the Standard discharge capacity (=2,750mAh) is
100%.
7.7 Charge Rate Capabilities

Discharge capacity is measured with constant current 2,750mA and 2.50V cut-off
after the cell is charged with 4.2V at 25°C as follows.
Charge Condition
Current 0.5C 1.0C
(1,375mA) (2,750mA)
Cut-off 3h or 0.02C 2.5h or 0.02C
Relative 100% 97%
Capacity
Note: Percentage as an index of the Rated discharge capacity (=2668mAh) is 100%.
7.8 Discharge Rate Capabilities

Discharge capacity is measured with the various currents in under table and 2.50V
cut-off after the Standard charge at 25°C.

Discharge Condition
Current 0.2C 1C 2C 3C
(550mA) (2750mA) (5500mA) (8250mA)
Relative 100% 97% 95% 92%
Capacity
Note: Percentage as an index of the Standard discharge capacity (=2,750mAh) is

100%.
7.9 Cycle Life

Each cycle is an interval between the charge (charge current 1,735mA) with 0.05C
Cut-off and the discharge (discharge current 2,750mA) with 2.50V cut-off.
Capacity after 500cycles.
Capacity ≥ 1,925mAh (70% of Rated Capacity)
7.10 Storage Characteristics

Capacity after storage for 30days at 60°C after the Standard charged (SOC50% at
25°C), measured with discharge current 2,750mA with 2.50V cut-off at 25℃.
Capacity recovery(after the storage) ≥ 2,400mAh (90% of Rated Capacity)
7.11 Status of the cell as of ex-factory

The cell should be shipped in 3.55V ~ 3.75V Charging voltage range.
8. Mechanical Characteristics
8.1 Drop Test

Test method: Cell(as of shipment or full charged) drop onto the oak-board
(thickness: ≥30mm) from 1.0m height at a random direction 6 times.
Criteria: No leakage
8.2 Vibration Test

Sample condition: Fully charged state 5samples
Test Method: 20±5℃/ 1.6mm max. excursion / 1Hz/minute between 10Hz to
55Hz to 10Hz / for mutually perpendicular directions
Criteria: No ventilation and leakage
(Test shall be performed with the following criteria IEC 62133, UL1642)
9. Safety
9.1 Overcharge Test

Test method: To charge the standard charged cell with 12V and 2,750mA at 25°C
for 2.5 hours.
Criteria: No fire, and no explosion.

9.2 External Short-circuit Test

Test method: To short-circuit the standard charged cell by connecting positive and
negative terminal by less than 80±20mΩ wire for 3 hours.
9.3 Reverse Charge Test

Test method: To charge reversely the standard charged cell with charge current
2,750mA for 2.5 hours.
9.4 Heating Test

Test method: To heat the standard charged cell at heating rate of 5°C per minute up to
130°C and keep the cell in oven for 60 minutes.
10. Warranty
Samsung SDI will be responsible for replacing the cell against defects or poor
workmanship
for 1year from the date of shipping. Any other problems caused by malfunction of the
equipment or unsuitable use of the cell are not under this warranty.
The warranty set forth in proper use, handling conditions described above,
and excludes in the case of a defect which is not related to manufacturing of the cell.
11. Others
11.1 Storage for a long time

If the cell is kept for a long time (3months or more), It is strongly recommended
that the cell is preserved at dry and low-temperature.
11.2 Other
Any matters that specifications does not have, should be conferred with
between the both parties.

12. Packaging
See Fig.2,
Package Drawing
Max. 18.40
Max. 65.00
Unit : mm
Fig. 1 Outline Dimensions of INR18650-29E

Fig 2. Package Drawing

Pack Quality Requirement for safety and quality epidemic issue
1.1. The battery pack’s consumption current.

- Sleep Mode : Under 250uA.
- Shut Down Mode : Under 10uA / Under 3.0V.
Under 1uA / Under 2.5V.
1.2. SOC 0%
- Cell voltage in SOC 0% of Pack should be Min. 3.0V.
(Discharging Cut-off Voltage)
1.3. Operating Charging Voltage of a cell.
- Normal operating voltage of a cell is 4.20V
- Max operating voltage of a cell is 4.25V.
1.4. No continuous charge
- Charge cut-off condition : Cut-off Current over than 1/20C(Charging method:
CC-CV)
- Initial recharging condition : Remaining Capacity under than 90%
or voltage under than 4.10V
1.5. Pre-charging function
- Pre-charge function should be implemented to prevent abnormal high rate
charging after deep discharge.
- Pre-charging condition Operation : Under 3.0V
Charging current : Under 150mA/Cell.(Continuous)
Pre-charge stop (Normal Charge Start) : All cells reach 3.0V
1.6. Mechanical Guides.
- PCBA and Cell stack should have heat insulation material between
them.(Such as plastic barrier which is giving air isolation or non-thermal
conductive material.)
- B+ and B- wire connection should not be crossed each other. Do not make
wire which had the voltage difference more than 4.0V get together.
- The material such as double sided tape and rubber which are used in battery
pack should be verified for its flammability
If a customer’s battery pack cannot meet the requirements above,

SDI cannot take responsibility for a quality issue about a battery cell.
Proper Use and Handling of Lithium Ion Cells

See before using lithium-ion cell

Supplied by
Samsung SDI Co., Ltd.
1. General
This document has been prepared to describe the appropriate cautions and
prohibitions, which the customer should take or employ when the customer uses
and handles the lithium ion cell to be manufactured and supplied by Samsung SDI Co.,
Ltd., in order to obtain optimum performance and safety.
2. Charging
2.1. Charging current

Charging current should be less than maximum charge current specified in
the product specification.
2.2. Charging voltage

Charging should be done by voltage less than that specified in
2.3. Charging time

Continuous charging under appropriate voltage does not cause any loss of
characteristics. However, the charge timer is recommended to be installed
from a safety consideration, which shuts off further charging at time specified
in the product specification.
2.4. Charging temperature

The cell should be charged within a range of specified temperatures in
2.5. Reverse charging

The cell should be connected, confirming that its poles are correctly aligned.
Inverse charging should be strictly prohibited. If the cell is connected
improperly, it may be damaged.
3. Discharging
3.1. Discharging
3.1.1. The cell should be discharged at less than maximum discharge current
specified in the product specification.
3.2. Discharging temperature

3.2.1. The cell should be discharged within a range of temperatures specified in
3.2.2. Otherwise, it may cause loss of characteristics.
3.3. Over-discharging
3.3.1. The system should be equipped with a device to prevent further discharging
exceeding discharging cut-off voltage specified in the product
specification.(over-discharging)
3.3.2. Over-discharging may cause loss of performance, characteristics, of
battery function.
3.3.3. Over-discharging may occur by self-discharge if the battery is left for
a very long time without any use.
3.3.4. The charger should be equipped with a device to detect cell voltage and to
determine recharging procedures.
4. Storage
4.1. Storage conditions

4.1.1. The cell should be stored within a range of temperatures specified
4.1.2. Otherwise, it may cause loss of characteristics, leakage and/or rust.
4.2. Long-term storage

4.2.1. The cell should be used within a short period after charging because
long-term storage may cause loss of capacity by self-discharging.
4.2.2. If long-term storage is necessary, the cell should be stored at lower
voltage within a range specified in the product specification, because
storage at higher voltage may cause loss of characteristics.
5. Cycle life
5.1. Cycle life performance

5.1.1. The cell can be charged/discharged repeatedly up to times specified in
the produce specification with a certain level of capacity also specified
5.1.2. Cycle life may be determined by conditions of charging, discharging,
operating temperature and/or storage.
6. Design of System
6.1. Connection between the cell and the battery

6.1.1. The cell should not be soldered directly with leads. Namely, the cell
should be welded with leads on its terminal and then be soldered with
wire or leads to soldered lead.
6.1.2. Otherwise, it may cause damage of component, such as separator and
insulator, by heat generation.
6.2 Positioning the battery in the System

6.2.1. The battery should be positioned as possible as far from heat sources
and high temperature components.
6.2.2. Otherwise, it may cause loss of characteristics.
6.3. Mechanical shock protection of the battery
6.3.1. The battery should be equipped with appropriate shock absorbers in order to

minimize shock.
6.3.2. Otherwise, it may cause shape distortion, leakage, heat generation
and/or rupture.
6.4. Short-circuit protection of the cell

6.4.1. The cell is equipped with an insulating sleeve to protect short-circuit which
may occur during transportation, battery assembly and /or system
operation.
6.4.2. If the cell sleeve is damaged by some causes such as outside impact,
it may cause short-circuit with some wiring inside the battery.
6.5. Connection between the battery and charger/system

6.5.1. The battery should be designed to be connected only to the specified
charger and system.
6.5.2. A reverse connection of the battery, even in the specified system,
should be avoided by employing special battery design such as
a special terminals.
7. Battery Pack Assembly
7.1. Prohibition of usage of damaged cell

7.1.1. The cell should be inspected visually before battery assembly.
7.1.2. The cell should not be used if sleeve-damage, can-distortion and/or
electrolyte-smell is detected.
7.2. Transportation
7.2.1. If the cell is necessary to transport to order place, such as the
battery manufacturer, careful precautions should be taken to avoid
damage of cell.
8. Others
8.1. Disassembly
8.1.1. The cell should not be dismantled from the battery pack.
8.1.2. Internal short-circuit caused by disassembly may lead to heat generation
and/or venting.
8.1.3. When the electrolyte is coming in contact with the skin or eyes,
wash immediately with fresh water and seek medical advice.
8.2. Short-circuiting
8.2.1. Short-circuit results in very high current which leads to heat generation.
8.2.2. An appropriate circuitry should be employed to protect accidental
short-circuiting.
8.3. Incineration
8.3.1 Incinerating and disposing of the cell in fire are strictly prohibited,
because it may cause rupture.
8.4. Immersion
8.4.1 Soaking the cell in water is strictly prohibited, because it may cause
melt of components to damaged to functions.
8.5. Mixing use

8.5.1. Different types of cell, or same types but different manufacturer's cell
may lead to cell rupture or damage to system due to the different
characteristics of cell.
8.6. Battery disposal

8.6.1. Although the cell contains no environmentally hazardous component,
such as lead or cadmium. the battery should be disposed according to
the local regulations when it is disposed.
8.6.2. The cell should be disposed with a discharged state to avoid heat generation
by an inadvertent short-circuit.
8.7. Caution - The Battery used in this device may present a risk of fire or chemical burn if
mistreated. Do not disassemble, heat above 100°C or incinerate. Replace
battery with Samsung SDI battery only. Use of another battery may present a
risk of fire or explosion. Dispose of used battery promptly. Keep away from
children. Do not disassemble and do not dispose of in fire.
8.8. Warning – Attached
Handling precaution and prohibitions of lithium ion rechargeable cells and batteries

Inaccurate handling of lithium ion and lithium ion polymer rechargeable battery may cause leakage, heat,
smoke, an explosion, or fire.
This could cause deterioration of performance or failure. Please be sure to follow instructions carefully.
1.1. Storage
Store the battery at low temperature (below 20°C is recommended), low humidity, no dust and no
corrosive gas atmosphere.
1.2. Safety precaution and prohibitions

To assure product safety, describe the following precautions in the instruction manual of the
application.
[ Danger!]
■ Electrical misusage
Use dedicated charger.
Use or charge the battery only in the dedicated application.
Don't charge the battery by an electric outlet directly or a cigarette lighter charger.
Don't charge the battery reversely.
■ Environmental misusage
Don't leave the battery near the fire or a heated source.
Don't throw the battery into the fire.
Don't leave, charge or use the battery in a car or similar place where inside of temperature may be
over 60°C.
Don't immerse, throw, wet the battery in water / seawater.
■ others
Don't fold the battery cased with laminated film such as pouch and Polymer.
Don't store the battery in a pocket or a bag together with metallic objects such as keys, necklaces,
hairpins, coins, or screws.
Don't short circuit (+) and (-) terminals with metallic object intentionally.
Don't pierce the battery with a sharp object such as a needle, screw drivers.
Don't heat partial area of the battery with heated objects such as soldering iron.
Don't hit with heavy objects such as a hammer, weight.
Don't step on the battery and throw or drop the battery on the hard floor to avoid mechanical shock.
Don't disassemble the battery or modify the battery design including electric circuit.
Don't solder on the battery directly.

Don't use seriously scared or deformed battery.

Don't put the battery into a microwave oven, dryer ,or high-pressure container.
Don't use or assemble the battery with other makers' batteries, different types and/or models of
batteries such as dry batteries, nickel-metal hydride batteries, or nickel-cadmium batteries.
Don't use or assemble old and new batteries together.
[ Warning! ]
Stop charging the battery if charging isn't completed within the specified time.
Stop using the battery if the battery becomes abnormally hot, order, discoloration, deformation, or
abnormal conditions is detected during use, charge, or storage.
Keep away from fire immediately when leakage or foul odors are detected. If liquid leaks onto your
skin or cloths, wash well with fresh water immediately.
If liquid leaking from the battery gets into your eyes, don't rub your eyes and wash them with clean
water and go to see a doctor immediately.
If the terminals of the battery become dirty, wipe with a dry cloth before using the battery.
The battery can be used within the following temperature ranges. Don't exceed these ranges.
Charge temperature ranges : 0°C ~ 45°C
Discharge Temperature ranges : -20°C ~ 60°C
Store the battery at temperature below 60°C
Cover terminals with proper insulating tape before disposal.
[ Caution! ]
■ Electrical misusage
Battery must be charge with constant current-constant voltage (CC/CV).
Charge current must be controlled by specified value in Cell specification.
Cut-off Voltage of charging must be 4.20V
Charger must stop charging battery by detecting either charging time or current specified in Cell’s
specification.
Discharge current must be controlled by specified value in Cell’s specification.
Cut-off Voltage of discharging must be over 2.5V.
■ others
Keep the battery away from babies and children to avoid any accidents such as swallow.
If younger children use the battery, their guardians should explain the proper handling method and
precaution before using.
Before using the battery, be sure to read the user's manual and precaution of it's handling.

Before using charger, be sure to read the user's manual of the charger.
Before installing and removing the battery from application, be sure to read user's manual of the
application.
Replace the battery when using time of battery becomes much shorter than usual.
Cover terminals with insulating tape before proper disposal.
If the battery is needed to be stored for an long period, battery should be removed from the
application and stored in a place where humidity and temperature are low.
While the battery is charged, used and stored, keep it away from object materials with static electric
chargers.
Safety handling procedure for the transporter

■ Quarantine
Packages that are crushed, punctured or torn open to reveal contents should not be transported.
Such packages should be isolated until the shipper has been consulted, provided instructions and, if
appropriate, arranged to have the product inspected and repacked.
■ Spilled Product
In the event that damage to packaging results in the release of cells or batteries, the spilled
products should be promptly collected and segregated and the shipper should be contacted for
instructions.
Design of positioning the battery pack in application and charger

To prevent the deterioration of the battery performance caused by heat, battery shall be positioned
away from the area where heat is generated in the application and the charger.
Design of the battery pack

Be sure adopting proper safe device such as PTC specified type or model in Cell Specification. If
you
intend to adopt different safety device which is not specified in Cell Specification, please contact
Samsung SDI to investigate any potential safety problem.
Be sure designing 2nd protective devices such as PTC & PCM at the same time to protect Cell just
in case one protective device is fault.
Please contact following offices when you need any help including safety concerns.

Samsung SDI Emergency Contact Information
■ Samsung SDI Chonan factory CS group.

508, Sungsung-Dong, Chonan City, Chungchongnam-Do, Korea
Tel:(+82)70-7125-1806 Fax:(+82)41-560-3697
■ Samsung SDI America office.

18600 Broadwick Street Rancho Dominguez CA 90220
Tel:(+1)310-900-5205 Fax:(+1)310-537-1033
■ Samsung SDI Taiwan office.

Rm. 3010, 30F., 333, Keelung Rd. Sec. 1, Taipei, Taiwan
Tel:(+886)2-2728-8469 Fax:(+886)2-2728-8480

INR18650 29E Samsung

Uploaded by

Copyright:

Available Formats

INR18650 29E Samsung

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

INR18650 29E Samsung

Uploaded by

Copyright:

Available Formats

SAMSUNG SDI Confidential Proprietary

Spec. No. INR18650-29E Version No. 1.1

2.Product : Lithium-ion Battery

3.SDI Model : INR18650-29E

5.Date of Application (YY/MM/DD) : 2012/09/19

6.Supplier : SAMSUNG SDI Co., Ltd.

Issued Checked Approved

Hanks Kang Michael Rim

Spec. No. INR18650-29E Version No. 1.1

1 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

2. Description and Model

3.1. Nominal Capacity 2,850mAh (0.2C, 2.50V discharge)

3.1.1. Typical Capacity 2,850mAh (0.2C, 2.50V discharge)

3.6. Charging Time Standard charge: 3hours

3.7. Max. Charge Current 2750mA (not for cyclelife)

3.10. Cell Weight (max. (g)) 48g

2 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

There shall be no such defects as scratch, rust, discoloration, leakage which

6. Standard Test Conditions

6.1 Environmental Conditions

6.2 Measuring Equipment

7.1 Standard Charge

7.2 Standard Discharge Capacity

7.3 Rated Discharge Capacity

7.4 Initial internal impedance

7.5 Temperature Dependence of Discharge Capacity

3 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

Charge Temperature Discharge temperature

Relative Capacity 60% 97% 97%

Note: If charge temperature and discharge temperature is not the same,

7.6 Temperature Dependence of Charge Capacity

Charge temperature Discharge temperature

Note: If charge temperature and discharge temperature is not the same,

7.7 Charge Rate Capabilities

Note: Percentage as an index of the Rated discharge capacity (=2668mAh) is 100%.

7.8 Discharge Rate Capabilities

4 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

Note: Percentage as an index of the Standard discharge capacity (=2,750mAh) is

7.9 Cycle Life

Capacity ≥ 1,925mAh (70% of Rated Capacity)

7.10 Storage Characteristics

Capacity recovery(after the storage) ≥ 2,400mAh (90% of Rated Capacity)

7.11 Status of the cell as of ex-factory

8.1 Drop Test

8.2 Vibration Test

9.1 Overcharge Test

5 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

9.2 External Short-circuit Test

9.3 Reverse Charge Test

9.4 Heating Test

11.1 Storage for a long time

6 Samsung SDI., Battery Business Division.

Spec. No. INR18650-29E Version No. 1.1

Fig. 1 Outline Dimensions of INR18650-29E