Hot Dip Galvanizing

A guide to the benefits

Why specify galvanizing? Total protection
Every part of a galvanized article is protected, both No other coating applied to a structure or fabrication
inside and out. No other coating provides the after completion can provide the level of protection
same protection. achieved by hot dip galvanizing. Appropriate metal
protection at the start can bring worthwhile economic
Steel does conjure up notions of strength,
benefits by reducing or eliminating the need for
resilience and durability – but even steel can need
maintenance and by extending the physical life of
the kind of protection that only hot dip galvanizing
structures and equipment.
can provide.
Harder than steel
To eliminate long-term costs caused by the need
The reaction of molten zinc with the steel during the
for continuous maintenance, the right metal
hot dip galvanizing process results in a coating that is
protection is needed at the very outset. Hot dip
metallurgically bonded to the steel. Zinc grows onto
galvanizing provides total lifelong corrosion
the steel surface to create zinc-iron alloy layers that are
protection for steel. Do it once. Do it right.
harder than the underlying steel. This super-hard coating
No other type of metal protection coating matches can help reduce potential cost overruns caused due to
galvanizing’s unique combination of benefits: damage during transit or erection.
The low cost alternative Cathodic protection
The long-term investment in hot dip galvanizing is Zinc galvanized coatings corrode preferentially to steel,
low compared to many other commonly specified providing cathodic or sacrificial protection should any
protective coatings for steel. Even where initial small areas of steel become exposed through damage in
cost is higher than alternative coatings, hot dip erection or transit.
galvanizing is invariably cheaper in the long-
Experience and expertise
term because of its high life expectancy and low
The team at Perry Metal Protection Limited are masters
maintenance requirements.
of hot dip galvanizing. They have been galvanizing steel
Speed of application since the early 1970s, with an impressive range of large-
A full protective galvanized coating can be applied scale projects. They offer you industry-leading technical
in minutes to even the most complex of structures and project management knowledge at no extra cost to
and application is not dependent on favourable the specifier or engineer.
weather conditions or the constraints of a
Perry Metal Protection Limited is the only galvanizing
multi-coat application. The simplicity of the
company equipped to offer you their unique system of
process is of real benefit when having to meet
service from design stage to delivery on site.
an ever-decreasing construction timeline.
The following pages give an overview of how to specify
Ease of inspection
for hot dip galvanizing. If you require any further details,
Coating quality can be assessed readily by eye.
please contact your local Perry Metal Protection site or
The galvanizing process is such that if the coating
visit our website at www.perrymetalprotection.co.nz
appears sound and continuous, it is sound
and continuous.

metal protection
0800 508 506
www.perrymetalprotection.co.nz
 How to specify design for hot dip galvanizing
Heavy duty after fabrication galvanizing help identify the appropriate specification to ensure
AS/NZS 4680 is the standard of galvanizing finish the best possible finish.
required when aesthetic appearance is needed for Design
the purposes of structural and decorative use. Discuss your design with our representative during
Full details are available from a Perry Metal the detailing stage as specifications can have
Protection representative. significant effect on the finish and possible
Self-finish coating cost savings.
The specified finish of the galvanized coating Where practical, each structure should fit inside the
should take account of the need for visual galvanizing bath in a single dip. Alternatively, modular
uniformity and be capable of handling physical construction is the solution. The welding quality
contact in public areas. These aspects should be should be specified to be free from porosity and
agreed with our representative prior to galvanizing. weld slag and grinding marks minimised as they may
Steel composition also plays a critical part as appear in the finished galvanized coating.
silicon and phosphorous levels can affect coating Inspection
appearance and uniformity. Allow for slightly The finished galvanized work should be inspected
thicker and rougher coatings if steel containing prior to dispatch or a sample of the type of finish
excessive levels of silicon and phosphorous are agreed before galvanizing.
used in fabrication. Perry Metal Protection can

Drain and vent hole sizes (min) for various hollow sections
Hollow Section Type and size Minimum vent
Circular H.S. Sq. H.S. Rectangular H.S. and drain
hole size (dia)
Nominal Bore Outside Diameter Outside Dimn’s Outside Dimn’s
Ref. No. (mm) (mm) (mm) Vent (mm) Drain (mm)

1 8 13.5 - - - -
2 10 17.2 - - - -
3 15 21.3 13 x 13 - - -
4 20 26.9 16 x 16 - - -
5 25 33.7 19 x 19 - - -
6 32 42.4 25 x 25 38 x 19 8 8
7 40 48.3 32 x 32 38 x 25 - -
8 50 60.3 38 x 38 51 x 25 - -
9 65 76.1 51 x 51 64 x 38, 76 x 38 - -
10 80 88.9 64 x 64 76 x 51, 89 x 38 - -
11 100 114.3 76 x 76 - - -
12 - - 89 x 89 - - -
13 - - - 102 x 51, 102 x 76 12 12
14 - - - 127 x 51, 127 x 64 12 12
15 125 139.7 102 x 102 127 x 76, 152 x 76 16 16
16 150 165.1 127 x 127 152 x 102 25 25
17 200 219.1 152 x 152 203 x 102, 203 x 152 32 32
18 250 273.0 203 x 203 254 x 152 63 63
19 300 323.9 254 x 254 305 x 203 75 75
20 350 355.6 305 x 305 305 x 254 88 88
21 400 406.4 - - 100 100

1. The above drain and vent hole sizes represent the minimum 3. For larger sections use the associated table for tanks, on page 8.
acceptable and it is preferred that the full tube cross section 4. Should the above hole size be unacceptable contact your local
be provided. Perry Metal Protection representative for further advice.
2. The above table is also applicable to hollow sections 5. Lifting eyes need to be provided for the hanging of steel
fabricated from channels and angles etc. Use the table with work, (adjacent same side as vent hole) or provide
the appropriate outside dimensions of the boxed section. holes for lifting wires.

2
 Draining and venting
Tubular fabrications and hollow sections
Tubular assemblies such as handrails, pipe Since proper galvanizing demands that the inside, as
columns, pipe girders, steel light poles, well as the outside, be completely cleaned and coated
transmission poles, pipe trusses, and sign bridges with zinc, air and ash must be allowed to flow in and
are commonly galvanized. completely wet the surfaces.

Cleaning In all tables of draining, venting and gusset bevel

As with all steel to be galvanized, pipe, R.H.S. calculations, allowance has been made for the
and other hollow materials must be thoroughly speedy and total expulsion of entrapped air and ‘ash’
cleaned before the molten zinc will bond with the produced during the galvanizing process.
base steel to produce the galvanized coating Simply stated, the structure must be lowered into the
inside and out. solution without trapping any air. It must be raised
R.H.S and pipe commonly presents two from the solution without trapping any solution.
cleaning challenges: Consequently, ample passageways which allow flow in
and out must be designed into the assemblies.
1. The ‘mill coating’ (varnish,lacquer, ‘Japan
black’ and similar materials) applied by the Since items to be galvanized are immersed and
manufacturer cost extra to remove at the withdrawn at an angle, the vent holes should be
galvanizing plant. Some formulations, both located at the highest point and drainage holes at the
foreign and domestic, are extremely difficult to lowest point in each hollow member. (Refer Fig 1)
remove with cleaning solutions and abrasive All components of fabricated hollow sections can be
blasting is required. inter-connected with full open tee or with mitred
2. Use only water-soluble cutting fluids when joints. Each closed section must be provided with
drilling to avoid steel contamination that may a vent hole and drain hole.
incur extra cleaning costs. Most galvanizers prefer to visually identify the venting
Venting from the outside when the assembly is received. This
It is mandatory that tubular fabrications and is necessary to check the adequacy of the venting as
hollow sections be properly vented. (Refer Fig 2) well as to determine that it has not been omitted by
mistake. Perry Metal Protection must be notified in
Any pickling acid or rinse waters that might be
writing if fabrications are internally vented.
trapped in a blind or closed joint connection will
be converted to super-heated steam and can Base plates and end plates must be designed to
develop a pressure of up to 26.2mpa (3800 psi) facilitate venting and draining. Fully cutting the plate
when immersed in molten zinc at 450˚c. This is provides minimum obstruction to a full, free flow
a serious potential hazard to galvanizing into and out of hollow sections. Since this is not
equipment and to personnel. always possible, the use of vent holes in the plate
often provides a solution.

Fig 1. Aspects of Internal Drilling Fig 2. Hollow Components

Individually drilled Internally drilled items can be DON’T BLOW IT!
components can be gas cut or drilled prior to welding Air inside any hollow component turns
awkward to drill, unsightly (visibly pleasing) fewer ‘run’ marks instantly to superheated steam when VENTING METHODS
(especially handrails) immersed in molten zinc (450˚c) and Common cases with two methods
and can leave ‘runs’ like a boiler will explode if sealed! of venting each shown
from drain holes
Vent at
highest
point

Perry Metal Protection must be guaranteed that items are fully and 1. For drilling use only water-soluble cutting fluids
correctly internally vented, to avoid unnecessary drilling by our operators 2. Holes must be as close to section ends as possible
and potential danger to staff.

www.perrymetalprotection.co.nz
 Design and fabrication
Steel plate structures 6. Stiffeners or attachments welded to plates at

for hot dip galvanizing lifting points may be utilized as lifting lugs.

1. One hole or lifting lug required in plates 7. It is preferred that lugs be welded to the side

where detailed in Fig 1, 2 and 3. of plates where their removal after galvanizing
is NOT necessary. (e.g. Floor plates).
2. Two holes or lifting lugs required in plates
where detailed in Fig 4 (two holes or lugs 8. Cutting, shaping and welding of plates
in total/see below). If possible, plates should be cut from one
sheet to eliminate or minimize butt welds
3. Hole sizes
and stresses.
A. Plates up to and including 10mm thick
require 10mm dia. hole(s). 9. Platform plate
Welds should be kept to a minimum when
B. Plates over 10mm thick and up to and
welding plates to heavy sub-frames to minimize
including 16mm thick require 16mm
weld stresses that cause distortion
dia. hole(s).
during galvanizing.
C. Plates over 16mm thick require larger dia.
holes or lifting lugs (refer your local Perry Bolting or set screwing of plates to sub-frames
Metal Protection representative). is preferable.

4. Gauge or centres of holes/lifting lugs should It is preferable that fittings or attachments on

be 11/2 diameter of holes required for lifting plates be designed for bolted connection to plates
from edge of plate (Fig 5). to minimize weld stresses. When cutting plates
to shape, it is preferred that all operations be as
5. Lifting Lugs
uniform as possible. If plates exceed maximum
A. Lifting lugs should be welded into
sizes shown in Fig 4, refer to your local Perry Metal
plates in positions detailed.
Protection representative for further guidance.
B. Lug thickness should equal thickness
If large quantities of plates or flats of the same shape
of plate being galvanized.
and size are to be galvanized, refer to your local
C. Lugs should have sufficient weld to support Perry Metal Protection representative as holes can
plate during the galvanizing process. be eliminated through other jigging techniques.

One hole or lifting lug

One hole or lifting lug
al

One hole or lifting lug

on
ag
di

180
um

0m l
m ona
im

ma diag
ax

xim im um
m

um max
m

dia mm
m

18 0 0
00

go
na
18

Fig 1. Square Plate Fig 2. Rectangular Plate Fig 3. Shaped Plate

Fig 4 Fig 5
x diameter of hole

1/4 length 1/2 length 1/4 length

2000mm maximum

Holes or lifting lug positions

1/2

1/2 x diameter of hole

6000mm maximum

4
 Positions of drain and vent holes (min)
For hollow vessels
When both internal and external surfaces are to 4. Should above drain and vent hole locations be
be galvanized at least one filling and draining hole difficult to include during fabrication, contact
must be provided, with a vent diagonally opposite your local Perry Metal Protection representative
to allow the exit of air during immersion. Check for further advice.
the drainage table for minimum drainage and vent
When vessels and air receivers etc. are not to be
hole sizes for various tank capacities.
galvanized inside, ‘snorkel’ tubes or extended vent
Internal baffles should be cropped as illustrated. pipes may be fitted only after discussion with your local
Manholes should finish flush inside to prevent Perry Metal Protection representative to allow air to exit
trapping excess zinc. above the level of molten zinc in the galvanizing bath.
(Refer Fig 7)
1. Drain and vent holes are to be placed at
diagonally opposite locations, typically as
shown in Fig 1, 2 and 3.

2. Provide suitable lifting lugs. Fig 3

3. Drain and vent holes must be flush internally

and be located as close to corner welds
as possible.
Fig 4 (NB Figs 5 and 6 unacceptable).

Vent diagonally
opposite filling hole
Fig 1 Vent hole at least 30mm Fig 2 Fig 3
VENT
MITRED
CORNERS

TANK

Filling hole
at least 80mm

Cropped
Internal baffles cropped top and bottom internal baffle
to allow free passage of zinc, and prevent
trapping of air. Flanges should finish
flush inside. DRAIN

ACCEPTABLE
Nearest edge of drain
and vent holes to be
10mm maximum from Fig 7
weld or corner (Fig 4).

Fig 4
NOT ACCEPTABLE

Vent pipes connect

interior to the
atmosphere.

Fig 5 Fig 6

www.perrymetalprotection.co.nz
 Gussets and web
Welded gussets and webs on
columns, beams and channel
sections should have corners
cropped or holed:

1. To prevent the entrapment

of air pockets in corners.

2. To facilitate drainage during Alternatively, holes

placed as close to
withdrawal from the corners as practical.
galvanizing bath.
CROPPED CORNERS WELD
Welding
CROPPED GUSSETS
Use continuous welding
to avoid moisture traps.

Drilling
Use only water-soluble
cutting fluids.

End plates
Provide holes in end plates for
venting and draining or crop
section webs.

13mm holes placed as

close to corners as practical.

Overlapping surfaces
Avoid narrow gaps between plates,
overlapping surfaces and back-to-
back angles and channels. When
small overlaps are unavoidable,
seal edges by welding.

When left unsealed, small

overlapping areas may trap pickle
acid that can later escape to colour
or damage the galvanized coating.

Larger overlapping surfaces

100mm
If contacting surfaces cannot be
avoided, a hole 6mm in diameter 100mm
for every 0.01m of overlap area
2

should be placed in one of the

members and the perimeter of
the contacting area should be
continuously welded. The vent hole
in one member will ensure the 6mm hole drilled through RHS
to avoid possible air entrapment.
safety of galvanizing personnel and
prevent damage to the article. If
in doubt, contact your local Perry
Metal Protection representative.

6
 Gusset plate or abutment mitre sizes
Flange Width Flange Width

UNIVERSAL BEAMS UNIVERSAL COLUMNS

Flange Flange
UNEQUAL ANGLES Width
CHANNELS Width

Flange Width

RECTANGULAR HOLLOW
TAPER FLANGE BEAMS (R.S.J.)
SECTIONS (R.H.S.)

Bevel sizes
Bevel cuts for angles and channels = 25% of flange width.
II Beams and columns = 25% of half the flange width.
Bevel cuts for –
Bevel cuts for RHS End plates = 25% of half the widest side.

Fig 1
Flange Width
GUSSET PLATE OR ABUTMENT 160mm

40mm 40mm
45˚ 45˚

25% of Flange Width

40mm 40mm

Example
1. All bevel sizes listed are 45˚– e.g. 40mm bevel = 40 x 40 x 45 (see Fig 1).

2. Gusset plates or abutments in channels and beams have both ends bevelled.

3. If this is unacceptable contact should be made with your Perry Metal Protection representative.

www.perrymetalprotection.co.nz
 Drain and vent hole sizes (min) for various tank capacities
DRAIN AND FILLING HOLE SIZES
CAPACITY SINGLE HOLE DOUBLE HOLE AIR VENT HOLE

m3 Litre Dia (mm) Square (mm) Dia (mm) Square (mm) Dia (mm) Square (mm)
0.5 500 80 70 - - 30 25
1.0 1,000 112 100 2 x 80 2 x 70 40 35
1.5 1,500 138 122 2 x 98 2 x 86 48 44
2.0 2,000 160 142 2 x 112 2 x 100 56 50
2.5 2,500 178 158 2 x 125 2 x 112 63 56
3.0 3,000 195 173 2 x 138 2 x 122 70 62
3.5 3,500 212 187 2 x 150 2 x 132 75 66
4.0 4,000 225 200 2 x 160 2 x 142 80 70
4.5 4,500 240 212 2 x 170 2 x 150 85 75
5.0 5,000 252 224 2 x 178 2 x 158 90 80
5.5 5,500 265 235 2 x 187 2 x 166 94 83
6.0 6,000 276 245 2 x 195 2 x 173 98 86
6.5 6,500 288 255 2 x 203 2 x 180 102 90
7.0 7,000 300 265 2 x 212 2 x 187 106 94
7.5 7,500 310 274 2 x 218 2 x 194 110 97
8.0 8,000 320 283 2 x 225 2 x 200 114 100
8.5 8,500 330 292 2 x 233 2 x 206 117 103
9.0 9,000 340 300 2 x 240 2 x 212 120 106
9.5 9,500 348 308 2 x 246 2 x 218 122 109
10.0 10,000 356 316 2 x 252 2 x 224 125 112

1. Calculate cylindrical tank capacity as follows: 3. Refer Fig 1 and 2 (page 6) for drain and vent hole location.
Capacity (M3)+ 0.785 x D2 x L (Dia. and length in metres). 4. Should the above hole sizes be unacceptable contact
2. For tanks smaller than listed above the min. size your local Perry Metal Protection representative for
for drain hole = 50mm dia. further advice.
and vent hole = 30mm dia.

Clearance for moving parts

Drop handles, hinges, shafts, and spindles require provision of minimum radial clearances
as detailed in the table below, to allow for the thickness of the galvanized coating.

Shaft or spindle size Minimum hole clearance

Up to 10mm diameter 1mm
10 to 30mm diameter 2mm
Over 30mm diameter 2.0 to 2.5mm
Australian Standard 1214 specifies the
following oversize tapping allowances:
For advice on service, quotations and technical knowledge on
Nominal internal thread diameters up to and including
hot dip galvanizing, contact your local Perry Metal Protection site:
M24: 0.4 mm allowance.
Hamilton 14 Manchester Place, Te Rapa 07 850 0120
Nominal internal thread diameters over Auckland 14 Timothy Place, Rosebank 09 820 8471
M24 up M36: 0.5 mm allowance. Tauranga 119 Oropi Rd, Greerton 07 541 1344
Wellington 129 Hutt Park Rd, Gracefield 04 568 4139
Christchurch 5 Chinook Place, Hornby 03 349 0290
Talking technical – Design, specification and inspection of galvanized products
Alternatively, visit our website www.perrymetalprotection.co.nz
To ensure consistently good galvanized steel products, it is essential that the
or email enquiry@perry.co.nz
basic requirements outlined in these guides are incorporated at the design
and fabrication stages of production.
These technical guides are designed to be introductory only. All design
features should be discussed with a member of our advisory team. Close
liaison between the design engineer, materials engineer, specifier, fabricator
and galvanizer will ensure the highest galvanizing standards. Perry Metal
metal protection
Protection also distributes a free wallchart and a summary booklet.
0800 508 506
V12214

8 www.perrymetalprotection.co.nz