Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
12 views

Setting Menu - Fe700

The document describes the three system menus that are used to configure settings on a sonar device. System Menu 1 is used to set units of measurement and other display options. System Menu 2 is used to set the time and time adjustment settings. System Menu 3 is used to configure the depth ranges and select the transducer frequency.

Uploaded by

george orf
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
12 views

Setting Menu - Fe700

The document describes the three system menus that are used to configure settings on a sonar device. System Menu 1 is used to set units of measurement and other display options. System Menu 2 is used to set the time and time adjustment settings. System Menu 3 is used to configure the depth ranges and select the transducer frequency.

Uploaded by

george orf
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

3 SYSTEM MENU

3.1 System Menu The system menu 1 appears.


5. With the cursor selecting MENU SELECT,
The system menu should be set just after
operate the [ - ] or [ + ] key to select system
installation and is not always necessary to be
menu desired; 1, 2 or 3.
adjusted. If you change any items of the system
menu or even if you open the system menu, the SYSTEM MENU 1
sounding picture will be cleared. There are three MENU SELECT 1 2 3
DEPTH UNIT m ft fa
menus: 1,2,and 3.
SPEED UNIT kt MPH km/h
1. Select MENU with the MODE Selector. COURSE TRUE MAG
BOTTOM LOST OFF ALARM
CLUTTER
INTERFACE IEC NMEA
9 (0 16) TX OUTPUT OFF MIN MAX
ALARM SOUND 1 2 3
INTERFERENCE REJECT
OS DATA DATA1 DATA2
OFF IR1 IR2 IR3 LANGUAGE English
PICTURE ADVANCE : To select item
SLOW FAST - +: To set option
Select other mode to exit.
TREND
Press [ + ] at menu 1.
OFF ON Press [ - ] at menu 2.
INTERVAL SYSTEM MENU 2
5s 1 min 2 min MENU SELECT 1 2 3
1/2 TIME ADJUST INTERNAL EXTERNAL
HOUR 0 (0 23)
: To select item
MINUTE 0 (0 59)
- +: To set option SECOND 0 (0 59)
0:22:40

2. Press the [ ] key several times to display


following window. : To select item
- +: To set option
CAUTION!
Select other mode to exit.
SYSTEM MENU IS ONLY Press [ + ] at menu 2.
FOR INSTALLATION. DO Press [ - ] at menu 3.
NOT CHANGE SETTINGS.
SYSTEM MENU 3
MENU SELECT 1 2 3
GO TO SYSTEM MENU? BASIC RANGE1 5 (2 800)
NO YES RANGE2 10 m
RANGE3 20
2/2
RANGE4 40
: To select item RANGE5 100
- +: To set option RANGE6 200
RANGE7 400
RANGE8 800
3. Select YES by pressing the [+] key. TRANSDUCER 50kHz 200kHz
: To select item
Confirmation message “ARE YOU SURE?”
- +: To set option
appears. Select other mode to exit.
4. Press the [ + ] key again.

11
3.2 System Menu 1 3.3 System Menu 2
DEPTH UNIT: Selects unit of depth TIME ADJUST: Selects internal clock or external
measurement among meters, feet, or fathoms. clock (UTC clock). Default setting is INTERNAL.
Default setting is meters. For INTERNAL, set current hour, minute and
second with [ + ], [ - ], [ ] or [ ] key. The setting
If "ft" or "fa" is selected, the depth unit is shown
clock appears and it counts upward.
in red characters.
SYSTEM MENU 2
SPEED UNIT: Selects unit of speed MENU SELECT 1 2 3
measurement among knots, statute miles per TIME ADJUST INTERNAL EXTERNAL
hour, or kilometers per hour. Default setting is HOUR 0 (0 23)
MINUTE 0 (0 59)
knots. Requires speed data, from external
SECOND 0 (0 59)
device.
0:22:40
COURSE: Selects heading reference; true or
magnetic. Default setting is TRUE.
: To select item
BOTTOM LOST: Turns on or off the bottom loss - +: To set option
warning. ON sounds the alarm if the bottom Select other mode to exit.
signal is not detected. Default setting is alarm
ON.
If EXTERNAL is selected, the screen changes
INTERFACE: Selects I/O signal format between as follows.
the FE-700 and external equipment; IEC format SYSTEM MENU 2
or NMEA format. Default setting is IEC. MENU SELECT 1 2 3
TIME ADJUST INTERNAL EXTERNAL
Output Input
TIME DIFFERENCE AUTO MANUAL
IEC 61162-1 DPT RMA, RMC
GLL, VTG
0:22:40
ZDA, GGA
NMEA 0183 DBT (Ver.1.5) RMA, RMC
DBS (Ver.1.5) GLL, VTG
DPT (Ver.2.0) ZDA, GGA : To select item
- +: To set option
TX OUTPUT: Selects transmitter output power;
Select other mode to exit.
maximum, minimum or off. Off is for factory use.
Normally use MAX output.
TIME DIFFERENCE: Selects auto (UTC) or
ALARM SOUND: Selects audio alarm sound manual. Auto uses the time difference in ZDA
among 1, 2 or 3. Default setting is 1. (IEC 61162-1). In manual, it is necessary to
1: Continuous sound enter the time difference in hours and minutes.
2: Intermittent sound; 0.5 s on and 0.5 s off.
3: Intermittent sound; 1 s on and 1 s off.

OS DATA: Selects own ship data display mode;


DATA 1 or DATA 2. DATA1 is the default setting.
If a navigation device is not connected to the
FE-700, select DATA 2.

LANGUAGE: Currently English is only available.

12
3.4 System Menu 3
SYSTEM MENU 2 RANGE 1- 8: Activates or deactivates specific
MENU SELECT 1 2 3
range scales. Default ranges are 5, 10, 20, 40,
TIME ADJUST INTERNAL EXTERNAL
TIME DIFFERENCE AUTO MANUAL 100, 200, 400, and 800 (meters). Setting area is
TIME DIFF HOUR 0 (0 13) 2 m to 800 m. The ranges 20 m and 200 m can
TIME DIFF MIN 0 (0 59) not be changed. They are essential in this
TIME DIFF SIGN - , + equipment.

0:22:40 Note: Ranges must be set in numerical order.


: To select item For example, if range 1 is 5 m and range 3 is 20
- +: To set option m, range 2 should be between 6 and 19 m.
Select other mode to exit.
TRANSDUCER: Selects transducer to use; 50
kHz or 200 kHz. Default is 200 kHz.

13

You might also like