S6L1M-F4 Wdg.

07 - Technical Data Sheet

Standards

STAMFORD industrial alternators meet the requirements of the relevant parts of the IEC EN 60034 and the relevant
section of other international standards such as BS5000, VDE 0530, NEMA MG1-32, IEC34, CSA C22.2-100 and
AS1359. Other standards and certifications can be considered on request.

Quality Assurance

Alternators are manufactured using production procedures having a quality assurance level to BS EN ISO 9001.

Excitation and Voltage Regulators

Excitation System
AVR Type MX321 MX341
Voltage Regulation ± 0.5% ± 1% with 4% Engine Governing
AVR Power PMG PMG

No Load Excitation Voltage (V) 15.46

No Load Excitation Current (A) 0.79
Full Load Excitation Voltage (V) 53
Full Load Excitation Current (A) 2.7
Exciter Time Constant (seconds) 0.16

Page 1 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

Electrical Data
Insulation System H
Stator Winding Double Layer Concentric
Winding Pitch 2/3
Winding Leads 6
Winding Number 07
Number of Poles 4
IP Rating IP23

RFI Suppression BS EN 61000-6-2 & BS EN 61000-6-4,VDE 0875G, VDE 0875N.

Refer to factory for others
Waveform Distortion NO LOAD < 1.5% NON-DISTORTING BALANCED LINEAR LOAD < 5.0%
Short Circuit Ratio 1/Xd
Steady State X/R Ratio 25.56
60 Hz
Telephone Interference TIF<50
Cooling Air Flow 1.27 m³/sec
Voltage Star (V) 600
Voltage Delta (V) 347
- -

kVA Base Rating (Class H) for

1275
Reactance Values (kVA)

Saturated Values in Per Unit at Base Ratings and Voltages

Xd Dir. Axis Synchronous 1.74
X'd Dir. Axis Transient 0.13
X''d Dir. Axis Subtransient 0.10
Xq Quad. Axis Reactance 1.61
X''q Quad. Axis Subtransient 0.24
XL Stator Leakage Reactance 0.05
X2 Negative Sequence Reactance 0.13
X0 Zero Sequence Reactance 0.04
Unsaturated Values in Per Unit at Base Ratings and Voltages
Xd Dir. Axis Synchronous 2.09
X'd Dir. Axis Transient 0.15
X''d Dir. Axis Subtransient 0.12
Xq Quad. Axis Reactance 1.65
X''q Quad. Axis Subtransient 0.29
XL Stator Leakage Reactance 0.06
Xlr Rotor Leakage Reactance 0.07
X2 Negative Sequence Reactance 0.16
X0 Zero Sequence Reactance 0.04

Page 2 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

Time Constants (Seconds)

T’d Transient Time Const. 0.104
T’’d Sub-Transient Time Const. 0.012
T’do O.C. Field Time Const. 4.066
Ta Armature Time Const. 0.027
T’’q Sub-Transient Time Const. 0.011
0
Resistances in Ohms (Ω) at 22 C
Stator Winding Resistance (Ra), per
phase for series connected 0.0024

Rotor Winding Resistance (Rf) 2.13

Exciter Stator Winding Resistance 19.56
Exciter Rotor Winding Resistance per
phase 0.1

PMG Phase Resistance (Rpmg) per

phase 1.91

Positive Sequence Resistance (R1) 0.0030

Negative Sequence Resistance (R2) 0.0035
Zero Sequence Resistance (R0) 0.0030
Saturation Factors 600V
SG1.0 0.184
SG1.2 0.685
Mechanical Data
Shaft and Keys
All alternator rotors are dynamically balanced to better than BS6861: Part 1 Grade 2.5 for
minimum vibration in operation. Two bearing generators are balanced with a half key.

1 Bearing 2 Bearing
SAE Adaptor SAE0,1 SAE0,1
Moment of Inertia 23.475 kgm² 22.95 kgm²
Weight Wound Stator 1098kg 1098kg
Weight Wound Rotor 966kg 924kg
Weight Complete Alternator 2326kg 2269kg
Shipping weight in a Crate 2369kg 2312kg
Packing Crate Size 170x90x153(cm) 170x90x153(cm)
Maximum Over Speed 2250 RPM for two minutes
Bearing Drive End - BALL 6224
Bearing Non-Drive End BALL 6317 BALL 6317

Page 3 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

THREE PHASE EFFICIENCY CURVES

60Hz

Page 4 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

Locked Rotor Motor Starting Curves - Separately Excited

60Hz

60Hz Locked Rotor Motor Starting Curves - Self Excited

Transient Voltage Dip Scaling Factor Transient Voltage Rise Scaling Factor
PF Factor
< 0.5 1 For voltage rise multiply voltage dip by 1.25
0.5 0.97
0.6 0.93
0.7 0.9
0.8 0.85
0.9 0.83
Page 5 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

Three-phase Short Circuit Decrement Curve - Separately Exited

60Hz

Sustained Short Circuit = 4517 Amps

60Hz

Sustained Short Circuit = Amps

Note 1 Note 2
The following multiplication factors should be The following multiplication factor should be used to convert the
used to adjust the values from curve between values calculated in accordance with NOTE 1 to those
time 0.001 seconds and the minimum current applicable to the various types of short circuit :
point in respect of nominal operating voltage :

50Hz 60Hz 3-phase 2-phase L-L 1-phase L-N

Voltage Factor Voltage Factor Instantaneous x 1.00 x 0.87 x 1.30
- - 600V - Minimum x 1.00 x 1.80 x 3.20
- - - - Sustained x 1.00 x 1.50 x 2.50
- - - - Max. sustained duration 10 sec. 5 sec. 2 sec.
- - - - All other times are unchanged
The sustained current value is constant irrespective of
Note 3
voltage level Curves are drawn for Star connected machines under no-load
excitation at rated speeds. For other connection the following
multipliers should be applied to current values as shown :
Parallel Star = Curve current value X 2
Series Delta = Curve current value X 1.732

Page 6 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

Typical Alternator Operating Charts

600V/60Hz

480V/60Hz

Page 7 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
 S6L1M-F4 Wdg.07

RATINGS AT 0.8 POWER FACTOR

Class - Temp Rise Cont. H - 110/50°C Cont. F - 90/50°C Cont. B - 70/50°C

Series Star (V) N/A N/A N/A N/A
50 kVA N/A N/A N/A N/A

Hz kW N/A N/A N/A N/A

Efficiency (%) N/A N/A N/A N/A
kW Input N/A N/A N/A N/A

Series Star (V) N/A 600 600 600

60 kVA N/A 1275 1176 1010
Hz kW N/A 1020 941 808
Efficiency (%) N/A 95.9 95.9 95.9
kW Input N/A 1064 981 843

De-Rates
All values tabulated above are subject to the following reductions:
- 5% when air inlet filters are fitted
- 3% for every 500 meters by which the operating altitude exceeds 1000 meters above mean sea level
- 3% for every 5°C by which the operational ambient temperature exceeds 40°C
- For any other operating conditions impacting the cooling circuit please refer to applications

Note: Requirement for operating in an ambient exceeding 60°C and altitude exceeding 4000 meters must be
referred to applications.

Dimensional and Torsional Drawing

For dimensional and torsional information please refer to the alternator General Arrangement and rotor drawings
available on our website (http://stamford-avk.com/)

Note: Continuous development of our products means that the information contained in our data sheets can
change without notice, and specifications should always be confirmed with Cummins Generator
Technologies prior to purchase.

Page 8 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018
Follow us @stamfordavk

Cummins Generator Technologies

View our videos at youtube.com/stamfordavk

news.stamford-avk.com

For Applications Support:

applications@cummins.com

For Customer Service:

emea.service@cummins.com

For General Enquiries:

Stamford-avk@cummins.com

Copyright 2016. Cummins Generator Technologies Ltd. All rights reserved.

Cummins and the Cummins logo are registered trade marks of Cummins Inc.
STAMFORD is a registered trade mark of Cummins Generator Technologies Ltd.

Page 9 S6L1M-F4_Wdg.07_A061J554_Rev.A_23.10.2018