Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
426 views

COC Mechatronics Level-IV

Uploaded by

basol7121921
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
426 views

COC Mechatronics Level-IV

Uploaded by

basol7121921
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Mechatronics Level-IV COC

Part -I-CHOOSE THE CORRECT ANSWER


1. If there are 3 identical resistors connected parallel the total resistance will be.
A) 3 time each individual resistors
B) 2/3 times each individual resistor
C) 1/3 times each individual resistors
D) 4/3 times each individual resistors
2. The responsible person to maintain the quality of work performed by a work team.
A, supervisor
B, all members of the team
C, worker
D, quality assurance officer
3. Resistivity of a conductor is mostly affected by .
A, composition
B, pressure
C, Temperature
D, current
4. Written communication methods may include.
A) Discussion
B) Negotiation
C) Speeches
D) Instructions
5. What should you do when a problem arises while you are repairing electronic equipment that you cannot solve by
yourself?
A, quit repairing
B, throw it away
C, ask for assistance
D, murmuring & crying
6. What is the power factor in capacitive
A, zero
B, unity
C, lagging
D, leading
7. The starting winding of a single phase motor is placed in the----
A. rotor
B. stator
C. armature
D, field
8. The frequency of DC supply is …….
A, zero
B, 16HZ
C, 50 HZ
D, 100HZ
9. The demand factor for the electrical system is the ratio of
A) Maximum demand to connected load
B) Maximum demand to average load
C) Average power to maximum power
D) Relative power to total power
10. Dielectric materials are
A) Insulating materials
B) Semiconducting materials
C) Magnetic materials
D) Ferroelectric materials
11. Transformer cores are laminated in order to:
A) Simplify its construction

1
Mechatronics Level-IV COC
B) Minimize eddy current loss
C) Reduce loss
D) Reduce hysteresis’s loss
12. Star – delta starter of an induction motor
A) Inserts resistance in rotor circuit
B) Inserts resistance in stator circuit
C) Applies reduced voltage to rotor
D) Applies reduced voltage to stator
13. Brushes of D.C. machines are usually made of
A) Hard copper
B) Soft copper
C) Carbon
D) All of above
14. The minimum change in input value that can be defected by measuring called
A) Threshold
B) Resolution
C) Sensitivity
D) Error
15. Multiplying resistor is required in
A) Ammeter
B) Power
C) Ohmmeter
D) Voltmeter
16. One of the following devices can be used to isolate the control circuit from the load.
A) Toggle switch
B) Relay
C) Circuit breaker
D) Rotary switch
17. The aim of preventive maintenance is to
A) Increase the reliability of a tool or equipment.
B) Increase the failure rate of tool or equipment.
C) Reduce the life span of a tool or equipment.
D) Improve the standard quality of a tool or an equipment.
18. A transformer having 1000 primary turns is connected to a 250V AC supply for a secondary voltage 400 V. The
number of secondary turns should be
A) 1600
B) 250
C) 400
D) 125
19. An electronic component which is used as switching device
A) Capacitor
B) Zener diode
C) Resistor
D) Transistor
20. Basic meter movement has an internal resistance of 50hom and full scale deflection current 150MA. What will be the
value of the shunt resistor required to measure?
A) 20Ω
B) 35 Ω
C) 15 Ω
D) 50 Ω
21. The difference between the synchronous speed and the actual speed of an induction motor is known as
A) Regulation
B) Back lash
C) Slip
D) Lag

2
Mechatronics Level-IV COC

Part II. Matching A and B


C. Varistor
Column A D. Memory
1. DC Motor With constant Speed E. Effective Communication
2. Motor with High starting Torque F. Initiative
3. Current limiting Device G. Dc Series Motor
4. Used To Store Program & Data in Computer System
H. Shunt Motor
5. Proper Attitude toward Work
I. Feed Bake
6. Performance Of Operation Or Quality
J. Hard Disk Driver
Of Product or Service to ensure customer satisfaction is monitored.
K. Quality Control
7. Constrictive & Encouraging Idea for Improvement
L. Successful Team work
8. Voltage Transformer
M.
9. Current Transformer
10. Washing Machine
N.
11. The Unit of Inductance
12. Rectifier
O.
13. Inverter
14. Team Member Understand How Their Tasks Fit In With Other People’s
P.
tasks.
15. Each Members Co-operating with Everyone and assisting others when they
need help. Q.

R.

Answers key
Part -I-CHOOSE THE
CORRECT ANSWER

1. C
2. B
3. C
Column B 4. D
A. Henry 5. C
B. Spindle Motor 6. B
3
Mechatronics Level-IV COC
7. B
8. A
9. A
10. A
11. B
12. D
13. C
14. B
15. D
16. B
17. A
18. A
19. D
20. C
21. C

Part -II-Matching A and B


1. H
2. G
3. C
4. J
5. F
6. K
7. I
8. R
9. Q
10. M
11. A
12. O
13. P
14. E
15. L

You might also like