BAS306A

Model Question Paper -2

USN

Third Semester B.E. Degree Examination

Introduction to Drone Technology
TIME: 03 Hours Max. Marks: 100

Note: 01. Answer any FIVE full questions, choosing at least ONE question from each MODULE.

Bloom’s Co’s
Module – 1 Marks Taxonomy
Levl
Classify and explain about Drones in India L2 CO1
(a) 10
Q.1 Explain Generic UAV systems with a neat sketch L2 CO1
(b) 10

OR
Explain about Degrees of freedom and Stick movements L2 CO2
(a) 10
Q.2 Explain about USV with neat sketch and its advantages and L2 CO2
(b) disadvantages 10

Module – 2

Explain about the Pre-Flight checks for drones. L2 CO1

(a) 10

Q.3 Write a program for Arduino flame sensor L1 CO2

(b) 10

OR

Write a program to Servo motor and Stepper motor control with L1 CO2
(a) Arduino 10

Q.4 Distinguish between microcontroller and microprocessor L2 CO2

(b) 10
Module – 3

Q.5 (a) Explain in detail about Drone Licensing requirements procedure. L2 CO4
10
Explain in detail about NPNT Compliance L2 CO4
(b) 10
 BAS306A

OR Bloom’s Co’s
Marks Taxono
my Levl
Explain about certification types and schemes. L2 CO4
(a) 10
Q.6 (b) Explain about DGCA Rules and Regulation for Drones in India. 10 L2 CO4

Module – 4

Develop an equation for thrust generation for an UAV. L6 CO3

Q.7 (a) 10
Explain about different types of payloads for UAV L2 CO3
(b) 5

Explain Maneuver load diagram L2 CO3

(C) 5

OR

Explain about Solar cell with neat sketch. L2 CO3

Q.8 (a) 10

Explain about Hybrid Propulsions performance characteristics in L2 CO3

(b) drones 10

Module – 5

Explain about detailed Drone Repair Checklist for drones L2 CO5

(a) 10
Q.9
Explain about Tuning rules and procedure for drones. L2 CO5
(b) 10

OR

Q.10 CASE STUDIES: Explain any one detailed Construction and testing L3 CO5
from below case studies.
(a) 1. Agriculture purpose for drones with suitable diagram and program. 20
2. Firefighting purpose for drones with suitable diagram and
program.
 BAS306A
Model Question Paper -1
USN

Third Semester B.E. Degree Examination

Introduction to Drone Technology
TIME: 03 Hours Max. Marks: 100

Note: 01. Answer any FIVE full questions, choosing at least ONE question from each MODULE.

Module – 1 Marks
Classify and explain the UAV based on range, altitude, and size.
(a) 10
Q.1 Explain Longitudinal, Lateral, and dynamic stability with neat sketches.
(b) 10

OR
Explain in detail about the Nano drones with neat sketch and its Advantages and
(a) 10
disadvantages
Q.2 Write short notes on i) Hovering ii) Climbing iii) Descent iv) yaw
(b) 10

Module – 2

(a) Explain about basics components of drones with neat sketch. 10

Q.3
List out the Arduino sensors and explain about Digital Barometric pressure sensor and
(b) 10
smoke gas sensor.

OR

Classification of Telemetry system and explain about wireless telemetry with neat
(a) 10
block diagram and its applications
Q.4 Explain about Flight planning and Mission planning for drones
(b) 10
Module – 3

Q.5 (a) Explain about DGCA Rules and Regulation for Drones in India. 10

(b) Explain in detail about Pilot Licensing requirements procedure. 10

 BAS306A

OR Marks
Classify and explain about certifications process.
(a) 10
Q.6 (b) Explain in detail about NPNT Compliance 10
Module – 4

Explain the composite structures using in UAV and explain their manufacturing
Q.7 10
(a) techniques.

(b) Explain about Payload configurations for drones 10

OR

Q.8 (a) Explain about the launching methods and recovery methods used in UAV 10

(b) Explain about stepped piston engine with neat sketch. 10

Module – 5

(a) Explain about Testing procedure for drones. 10

Q.9

(b) Explain about Manufacturing constraints and Applications for drones. 10

OR

Q.10
(a) CASE STUDIES: Explain detailed Construction and testing of a basic drone. 20