Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 8 views

    134 BK 122019

    Uploaded by

    Ganga Maiya

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content

    134 BK 122019

    Uploaded by

    Ganga Maiya
    8 views1 page

    Original Title

    134 Bk 122019

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Report this Document

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    8 views1 page

    134 BK 122019

    Uploaded by

    Ganga Maiya

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Flag for inappropriate content
    Download as pdf or txt
    of 1

    Code No: 134BK R16

    JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD


    B.Tech II Year II Semester Examinations, December - 2019
    MANUFACTURING PROCESS
    (Mechanical Engineering)
    Time: 3 Hours Max. Marks: 75

    Note: This question paper contains two parts A and B.


    Part A is compulsory which carries 25 marks. Answer all questions in Part A.
    Part B consists of 5 Units. Answer any one full question from each unit.
    Each question carries 10 marks and may have a, b as sub questions.

    PART – A
    (25 Marks)
    1.a) List out any four types of patterns. [2]
    b) What are the desirable properties of moulding sand? [3]
    c) What are the types of flames used in oxy fuel welding? [2]
    d) List any three advantages of gas welding over arc welding. [3]
    e) Write any two differences between soldering and Brazing. [2]
    f) What are the causes and remedies of welding process: i) Spatter ii) Hot inclusions.[3]
    g) Define hot working. [2]
    h) Sketch the following: i) Planetary rolling mill ii) Cluster Rolling mill. [3]
    i) State the principle of extrusion and list the types of extrusion. [2]
    j) List out the common forging defects. [3]

    PART – B
    (50 Marks)
    2. Describe the process of centrifugal casting with neat sketch. What are the advantages?
    [10]
    OR
    3. List out the defects in casting process. Explain any five with neat sketch. [10]

    4. Explain the process of submerged arc welding with neat sketch. What are its advantages?
    [10]
    OR
    5. Explain the process of thermit welding with neat sketch. Write its applications. [10]

    6. Discuss various welding defects with cause and remedies. [10]


    OR
    7. What are the reasons and effects of Heat affected zone in welding? [10]

    8. Why recovery, recrystallization and grain growth are required after plastic deformation of
    a metal. Explain these process. [10]
    OR
    9. Derive the expression for roll separating force and power in rolling. [10]

    10.a) Write a shot notes on i) Wire drawing and ii) Tube drawing.
    b) What are the advantages and limitations of extrusion process? [5+5]
    OR
    11.a) Briefly explain hydrostatic extrusion process with neat sketch.
    b) List out the different forging operations. Explain drop forging operation with neat sketch.
    [5+5]
    www.manaresults.co.in ---ooOoo---

    You might also like