34 TT 25 13 STT750 Manual

STT750 SmartLine
Temperature Transmitter
User’s Manual
34-TT-25-13
Revision 4
September 2017
Honeywell Process Solutions

Copyrights, Notices and Trademarks
© Copyright 2017 by Honeywell, Inc.

Revision 4, September 2017
While the information in this document is presented in good faith and believed to be
accurate, Honeywell disclaims any implied warranties of merchantability and fitness for a
particular purpose and makes no express warranties except as may be stated in the written
agreement with and for its customers. In no event is Honeywell liable to anyone for any
indirect, special, or consequential damages. The information and specifications in this
document are subject to change without notice.
Honeywell, TDC 3000, SFC, SmartLine, PlantScape, Experion PKS, and TotalPlant are
registered trademarks of Honeywell International Inc. Other brand or product names are
trademarks of their respective owners.
Honeywell Process Solutions

1250 W Sam Houston Pkwy S
Houston, TX 77042
Page ii STT750 Temperature Transmitter User’s Manual Revision 4

About This Manual
This manual is a detailed how to reference for installing, piping, wiring, configuring, starting up,
operating, maintaining, calibrating, and servicing Honeywell’s family of STT750 Temperature
Transmitters. Users who have a Honeywell STT750 SmartLine Temperature Transmitter
configured for HART protocol are referred to the STT750 SmartLine Series HART Option User’s
Manual, document number 34-TT-25-15.
The configuration of your Transmitter depends on the mode of operation and the options selected
for it with respect to operating controls, displays and mechanical installation. This manual
provides detailed procedures to assist first-time users, and it further includes keystroke
summaries, where appropriate, as quick reference or refreshers for experienced personnel.
To digitally integrate a Transmitter with one of the following systems:
 For the Experion PKS, you will need to supplement the information in this document with the
data and procedures in the Experion Knowledge Builder.
 For Honeywell’s TotalPlant Solutions (TPS), you will need to supplement the information in this
document with the data in the PM/APM SmartLine Transmitter Integration Manual, which is
supplied with the TDC 3000 book set. (TPS is the evolution of the TDC 3000).
Release Information:
STT750 SmartLine Temperature Transmitter User Manual, Document # 34-TT-25-13,

Rev 1, August 2015 1st Release
Rev.2 March 2016 CVD, W5W26, Soft DO, Housing w/o plug, angle Brackets,
NAMUR 89 Approval, Ni 120 & Cu 10 inputs added
and Display menus updated.
Rev.3 November 2016 Roxspur Cu100 and GOST sensor types added
Rev.4 September 2017 Control drawing updated to Rev.D, EAC, KOSHA and
Marine approvals/certs and mtg dwgs updated.
Revision 4 STT750 Temperature Transmitter User’s Manual Page iii

References
The following list identifies publications that may contain information relevant to the information
in this document.
STT750 SmartLine Temperature Transmitter Quick Start Installation Guide, Document

# 34-TT-25-14
SmartLine Temperature Transmitter with HART Communications Options Safety Manual,
# 34-TT-25-05
STT750 SmartLine Temperature Transmitter HART Option User’s Manual, Document
# 34-TT-25-15
MC Toolkit User Manual, for MCT404, Document # 34-ST-25-50
PM/APM SmartLine Transmitter Integration Manual, Document # PM 12-410
STT750 Series Temperature, Transmitter, Agency IS Control Drawing 50091227
Smart Field Communicator Model STS 103 Operating Guide, Document # 34-ST-11-14
Patent Notice
The Honeywell STT750 SmartLine Temperature Transmitter family is covered by one or more of the
following U. S. Patents: 5,485,753; 5,811,690; 6,041,659; 6,055,633; 7,786,878; 8,073,098; and other
patents pending.
Support and Contact Information
For Europe, Asia Pacific, North and South America contact details, refer to the back page of this
manual or the appropriate Honeywell Solution Support web site:
Honeywell Corporate www.honeywellprocess.com
Honeywell Process Solutions https://www.honeywellprocess.com/smartline-temperature/
Training Classes http://www.automationccollege.com
Telephone and Email Contacts
Area Organization Phone Number

United States and 1-800-343-0228 Customer Service
Honeywell Inc.
Canada 1-800-423-9883 Global Technical Support
Global Email Honeywell Process
ask-ssc@honeywell.com
Support Solutions
Page iv STT750 Temperature Transmitter User’s Manual Revision 4

Symbol Descriptions and Definitions
The symbols identified and defined in the following table may appear in this document.
Symbol Definition
ATTENTION: Identifies information that requires special consideration.
TIP: Identifies advice or hints for the user, often in terms of performing a
task.
CAUTION Indicates a situation which, if not avoided, may result in equipment or work
(data) on the system being damaged or lost, or may result in the inability to
properly operate the process.
CAUTION: Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
CAUTION symbol on the equipment refers the user to the product manual for
additional information. The symbol appears next to required information in
the manual.
WARNING: Indicates a potentially hazardous situation, which, if not avoided,

could result in serious injury or death.
WARNING symbol on the equipment refers the user to the product manual
for additional information. The symbol appears next to required information
in the manual.
WARNING, Risk of electrical shock: Potential shock hazard where

HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4 Vpeak, or 60 VDC
may be accessible.
ESD HAZARD: Danger of an electro-static discharge to which equipment may

be sensitive. Observe precautions for handling electrostatic sensitive
devices.
Protective Earth (PE) terminal: Provided for connection of the protective

earth (green or green/yellow) supply system conductor.
Functional earth terminal: Used for non-safety purposes such as noise

immunity improvement. NOTE: This connection shall be bonded to
Protective Earth at the source of supply in accordance with national local
electrical code requirements.
Earth Ground: Functional earth connection. NOTE: This connection shall be

bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.
Chassis Ground: Identifies a connection to the chassis or frame of the

equipment shall be bonded to Protective Earth at the source of supply in
accordance with national and local electrical code requirements.
continued
Revision 4 STT750 Temperature Transmitter User’s Manual Page v

Symbol Description
The Factory Mutual® Approval mark means the equipment has been rigorously
tested and certified to be reliable.
The Canadian Standards mark means the equipment has been tested and meets
applicable standards for safety and/or performance.
The Ex mark means the equipment complies with the requirements of the
European standards that are harmonized with the 94/9/EC Directive (ATEX
Directive, named after the French "ATmosphere EXplosible").
Page vi STT750 Temperature Transmitter User’s Manual Revision 4

Contents
1. Introduction .................................................................................................................................... 1
1.1. Overview ................................................................................................................................ 1
1.2. Features and Options .............................................................................................................. 1
1.2.1. Physical Characteristics .................................................................................................. 1
1.2.2. Functional Characteristics .............................................................................................. 2
1.3. STT750 SmartLine Transmitter Nameplate ........................................................................... 3
1.4. Safety Certification Information............................................................................................. 3
1.5. Transmitter Adjustments ........................................................................................................ 3
1.6. Display.................................................................................................................................... 4
1.7. Optional 3-Button Assembly .................................................................................................. 4
2. Application Design ......................................................................................................................... 5
2.1. Overview ................................................................................................................................ 5
2.2. Safety ...................................................................................................................................... 5
2.2.1. Accuracy ......................................................................................................................... 5
2.2.2. Diagnostic Messages ...................................................................................................... 5
3. Installation and Startup ................................................................................................................... 7
3.1. Installation Site Evaluation..................................................................................................... 7
3.2. Honeywell MC Toolkit........................................................................................................... 7
3.3. Display Installation Precautions ............................................................................................. 7
3.4. Mounting STT750 SmartLine Temperature Transmitters ...................................................... 8
3.4.1. Summary......................................................................................................................... 8
3.4.2. Mounting Dimensions .................................................................................................. 10
3.4.3. Bracket Mounting Procedure ........................................................................................ 12
3.5. Wiring a Transmitter ............................................................................................................ 13
3.5.1. Loop Power Overview .................................................................................................. 13
3.5.2. Wiring Variations ......................................................................................................... 15
3.5.3. Loop Wiring Procedure ................................................................................................ 15
3.5.4. Grounding and Lightning Protection ............................................................................ 16
3.5.5. Explosion-Proof Conduit Seal ...................................................................................... 16
3.5.6. Input Sensor Wiring ..................................................................................................... 17
3.6. Startup .................................................................................................................................. 18
3.6.1. Overview ...................................................................................................................... 18
3.6.2. Startup Tasks ................................................................................................................ 18
3.6.3. Output Check Procedures ............................................................................................. 18
3.6.4. Constant Current Source Mode Procedure ................................................................... 19
4. Operation ...................................................................................................................................... 20
4.1. Overview .............................................................................................................................. 20
4.2. Three-Button Operation........................................................................................................ 20
4.2.1. Menu Navigation .......................................................................................................... 21
4.2.2. Data Entry..................................................................................................................... 21
4.2.3. Editing a Numeric Value .............................................................................................. 22
4.2.4. Selecting a new setting from a list of choices .............................................................. 22
4.2.5. The Display Menu ........................................................................................................ 23
4.3. Three Button Operation with no Display Installed ............................................................... 27
4.3.1. Zero Adjustment ........................................................................................................... 27
4.3.2. Span Adjustment .......................................................................................................... 27
Revision 4 STT750 Temperature Transmitter User’s Manual Page vii

4.4. Changing the Default Failsafe Direction.............................................................................. 28
4.4.1. Procedure to Establish Failsafe Operation ................................................................... 28
4.5. Monitoring the Display ........................................................................................................ 30
4.5.1. Display ......................................................................................................................... 30
5. Maintenance ................................................................................................................................. 31
5.1. Overview .............................................................................................................................. 31
5.2. Preventive Maintenance Practices and Schedules................................................................ 31
5.3. Replacing the Communication Module ............................................................................... 31
6. Calibration.................................................................................................................................... 34
6.1. Recommendations for Transmitter Calibration .................................................................... 34
6.2. Calibration Procedures ......................................................................................................... 34
7. Troubleshooting ........................................................................................................................... 35
7.1. Overview .............................................................................................................................. 35
7.2. Critical Diagnostics Screens ................................................................................................ 35
7.2.1. Fault Conditions and Recommended Corrective Actions ............................................ 35
8. Parts List ...................................................................................................................................... 36
8.1. Overview .............................................................................................................................. 36
Appendix A. PRODUCT CERTIFICATIONS .................................................................................... 40
9. Appendix B – Security ................................................................................................................. 57
8.2. How to report security vulnerability .................................................................................... 57
Glossary ............................................................................................................................................... 58
Page viii STT750 Temperature Transmitter User’s Manual Revision 4

List of Figures
Figure 1 – STT750 Major Assemblies ................................................................................................... 2

Figure 2 – Electronics Housing Components ......................................................................................... 2
Figure 3 –Typical STT750 Nameplate ................................................................................................... 3
Figure 4 – STT750 with adapter housing - Horizontal Wall Mounting ................................................. 8
Figure 5 – STT750 No-Adapter Horizontal Wall Mounting .................................................................. 8
Figure 6 – STT750 Pipe Mount with adapter housing - Horizontal & Vertical ..................................... 9
Figure 7 – STT750 Pipe Mount, Vertical ............................................................................................... 9
Figure 8 – STT750 with adapter housing - Dimensions....................................................................... 10
Figure 9 – STT750 no adapter housing dimensions ............................................................................. 11
Figure 10 – Pipe Mounting Bracket Secured to a Horizontal or Vertical Flat Pipe and Angle pipe .... 12
Figure 11 – HART/DE Transmitter Operating Ranges ........................................................................ 13
Figure 12 – Transmitter 9-Screw Terminal Board and Grounding Screw ........................................... 14
Figure 13 – STT750 Thermocouple, RTD, mV, ohm and Volt Connections ...................................... 17
Figure 14 – Current Loop Test Connections ........................................................................................ 19
Figure 15 - Three-Button Option .......................................................................................................... 20
Figure 16 – Locating the Failsafe and Write Protect Jumpers.............................................................. 28
Figure 17 – Display with Process Variable Format .............................................................................. 30
Figure 18 – PWA Replacement ............................................................................................................ 31
Figure 19 – Pipe and Wall Bracket Parts.............................................................................................. 37
Figure 20 – Electronic Housing, Display End ...................................................................................... 38
Figure 21 – Electronic Housing, Terminal Block End ......................................................................... 39
Revision 4 STT750 Temperature Transmitter User’s Manual Page ix

List of Tables
Table 1 – Features and Options.............................................................................................................. 1

Table 2 – Available Display Characteristics .......................................................................................... 4
Table 3 – STT750 Standard Critical Diagnostics Messages .................................................................. 6
Table 4 – STT750 Standard Non-Critical Diagnostics Messages .......................................................... 6
Table 5 – Three-Button Option Functions ........................................................................................... 21
Table 6 – Three-Button Data Entry...................................................................................................... 22
Table 7 – The Display Menus .............................................................................................................. 23
Table 8 – HART Failsafe and Write Protect Jumpers.......................................................................... 29
Table 9 – Fault Conditions and Recommended Corrective Actions. ................................................... 35
Table 10 – Summary List of Recommended Spare Parts .................................................................... 36
Table 11 – Pipe and Wall Bracket Parts .............................................................................................. 38
Table 12 – Transmitter Major Assemblies ........................................................................................... 38
Page x STT750 Temperature Transmitter User’s Manual Revision 4

1. Introduction
1.1. Overview
This section is an introduction to the physical and functional characteristics Honeywell’s family of
STT750 SmartLine Temperature Transmitters.
1.2. Features and Options

The STT750 SmartLine Temperature Transmitter is available in a variety of models for measuring
Thermocouples, RTDs, millivolts and Ohm. Table 1 lists the protocols, Human-Machine Interface
(HMI), materials, approvals, and mounting bracket options for the STT750.
Table 1 – Features and Options
Feature/Option Standard/Available Options

Communication Protocols HART version 7
Digital display
Human-Machine Interface (HMI) Three-button programming (optional)
Display language: English only
Calibration Single
Approvals (See Appendix A for
ATEX, CSA, FM, IECEx
details.)
Angle and flat pipe mounting and wall mounting brackets
Mounting Brackets
in carbon steel and 316 stainless steel.
1.2.1. Physical Characteristics

As shown in Figure 1, the STT750 is packaged in one major assembly: the Electronics Housing.
The elements in the Electronic Housing are connected to the process sensors, measure the process
variables, respond to setup commands and execute the software and protocol for the different
temperature measurement types. Figure 2 shows the assemblies in the Electronics Housing with
available options.
Revision 4 STT750 Temperature Transmitter User’s Manual Page 1

Housing adapter
may not be present
on all models
Figure 1 – STT750 Major Assemblies
Figure 2 – Electronics Housing Components
1.2.2. Functional Characteristics

The Transmitter measures process Temperature and outputs a signal proportional to the measured
process variable (PV), including 4 to 20mA.
An optional 3-button assembly is available to set up and make adjustments to the Transmitter. In
addition, a Honeywell Multi-Communication (MC) Toolkit (not supplied with the Transmitter) can
facilitate setup and adjustment procedures.
Page 2 STT750 Temperature Transmitter User’s Manual Revision 4

1.3. STT750 SmartLine Transmitter Nameplate
The Transmitter nameplate mounted on the bottom of the electronics housing (see Figure 1) lists its
model number, physical configuration, electronics options, accessories, certifications, and
manufacturing specialties. Figure 3 is an example of a typical Temperature Transmitter nameplate.
The model number format consists of a Key Number with several table selections.
Figure 3 –Typical STT750 Nameplate
You can readily identify the series and basic Transmitter type from the key number. The letter in the
third digit represents one of these basic transmitter types:
 T = Temperature
For a complete selection breakdown, refer to the appropriate Specification and Model Selection
Guide provided as a separate document.
1.4. Safety Certification Information

An “approvals” nameplate is located on the bottom of the Electronics Assembly; see Figure 1for
exact location. The approvals nameplate contains information and service marks that disclose the
Transmitter compliance information. Refer to Appendix A of this document for safety certification
requirements and details.
1.5. Transmitter Adjustments

Span adjustments are possible in STT750 SmartLine Temperature Transmitters with the optional
three-button assembly located at the top of the Electronic Housing (see Figure 2).
The user can also use the Honeywell MC Toolkit or other third-party hand-held to make any
adjustments to an STT750 SmartLine Temperature Transmitter.

1.6. Display
Table 2 – Available Display Characteristics

Display  Suitable for basic process needs
 360o rotation in 90o increments
 8 configurable screens
 2 lines,16 characters
 Standard units of measurement: °F, °C, °R, K, Ω, mV & %
 Diagnostic messaging
1.7. Optional 3-Button Assembly

The optional 3-Button Assembly is located under the nameplate and provides the following features
and capabilities:
 Increment, decrement, and enter key functions.

 With the menu-driven display:
o Comprehensive on-screen menu for navigation.
o Transmitter configuration.
o Transmitter calibration.
o Display configuration.
o Set span parameters.
o Viewing transmitter parameters

2. Application Design
2.1. Overview
This section discusses the considerations involved with deploying a Honeywell STT750 SmartLine
Temperature Transmitter in a process system. The following areas are covered:
 Safety
 Input and output data
 Reliability
 Environmental limits
 Installation considerations
 Operation and maintenance
 Repair and replacement
2.2. Safety
2.2.1. Accuracy
The STT750 SmartLine Temperature Transmitter (Transmitter) measures the temperature of a process
and reports the measurement to a receiving device. Refer to STT750 Specification,
34-TT-03-16.
2.2.2. Diagnostic Messages

Transmitter standard diagnostics are reported in the two basic categories listed in Table 3. Problems
detected as critical diagnostics drive the analog output to the programmed burnout level for HART.
Problems detected as non-critical diagnostics may affect performance without driving the analog
output to the programmed burnout level (for HART). Informational messages (not listed in Table 3)
report various Transmitter status or setting conditions. The messages listed in Table 3 are specific to
the Transmitter, exclusive of those associated with HART protocols. HART diagnostic messages are
listed and described in the STT750 SmartLine Temperature Transmitter HART Option User Manual,
document number 34-TT-25-15.

Table 3 – STT750 Standard Critical Diagnostics Messages
Critical Diagnostics
(Failure Conditions)
Temperature Sensor Module Failure
Communication Module Failure
Sensor Comm. Timeout
Input Fault
Table 4 – STT750 Standard Non-Critical Diagnostics Messages
Non-Critical Diagnostics (Warning Conditions)

Excess Cal Correct
(Excess LRV Correct and/or Span correct for Sensor Input)
Input Out of Range
(Sensor Input Under Range or Over Range)
Sensor Module Over Temperature
Cold Junction Out of Range Error
Sensor Input TB5, TB6, TB7 Open (RTD and Ohm)
No Factory Calibration
Supply Voltage Fault
(External Supply Voltage Fail)
Communication Module Over Temperature
No DAC Compensation
Unreliable communication between Sensor and Comm
Modules
Display NVM Fault
Internal Power Failure for Communication Module

3. Installation and Startup
3.1. Installation Site Evaluation
Evaluate the site selected for the STT750 SmartLine Transmitter installation with respect to the
process system design specifications and Honeywell’s published performance characteristics for your
particular model. Some parameters that you may want to include in your site evaluation are:
 Environmental Conditions:
o Ambient Temperature
o Relative Humidity
 Potential Noise Sources:
o Radio Frequency Interference (RFI)
o Electromagnetic Interference (EMI)
 Vibration Sources
o Pumps
o Motorized System Devices (e.g., pumps)
o Valve Cavitation
 Process Parameters
o Temperature
o Maximum Sensor Input Ratings
3.2. Honeywell MC Toolkit

In preparation for post-installation processes, refer to the MC Toolkit (MCT404) User Manual,
Document # 34-ST-25-50, for battery conditioning and device operation and maintenance
information.
3.3. Display Installation Precautions

Temperature extremes can affect display quality. The display can become unreadable at temperature
extremes; however, this is only a temporary condition. The display will again be readable when
temperatures return to within operable limits.
The display update rate may increase at cold temperature extremes, but as with readability, normal
updating resumes when temperatures are within limits for full operability.

3.4. Mounting STT750 SmartLine Temperature Transmitters
3.4.1. Summary
Transmitter models can be attached to a two-inch (50 millimeter) vertical or horizontal pipe using
Honeywell’s optional angle brackets.
Honeywell’s optional wall mounting bracket is also shown below:
TRANSMITTER ENCLOSURE CAN BE ROTATED A TOTAL OF 90O FROM THE
STANDARD MOUNTING POSITION
Figure 4 – STT750 with adapter housing - Horizontal Wall Mounting
Figure 5 – STT750 No-Adapter Horizontal Wall Mounting

Figure 6 – STT750 Pipe Mount with adapter housing - Horizontal & Vertical
Figure 7 – STT750 Pipe Mount, Vertical
*Note 1: Figure 6 and 7. The housing adapter may not be present on all transmitter models. If the
housing adapter is not present, subtract 24,5mm (0,96 inches) from the dimension specified.

3.4.2. Mounting Dimensions
Refer to Honeywell drawing number 50094836 for detailed dimensions of the transmitter assembly.
Abbreviated overall dimensions are also shown on the Specification Sheets for the transmitter
models. This section assumes that the mounting dimensions have already been taken into account and
the mounting area can accommodate the Transmitter.
Refer to Honeywell drawing numbers 50095917 (Flat Pipe Mount), 50095918 (Wall Mount) and
50124813 (Angle Pipe Mount) for detailed mounting specifications.
Figure 8 – STT750 with adapter housing - Dimensions

Figure 9 – STT750 no adapter housing dimensions

3.4.3. Bracket Mounting Procedure
1. Align the two mounting holes in the transmitter with the two slots in the mounting bracket
and assemble the (2) M8 hex cap screws, (2) lockwashers and (2) flat washers provided.
Rotate transmitter assembly to the desired position and torque the M8 hex cap screws to 27,0
Nm/20,0 Lb-ft maximum.
2. Pipe Mount Option: Refer to Figure 10. Position the bracket on a 2-inch (50.8 mm) horizontal
or vertical pipe, and install a “U” bolt around the pipe and through the holes in the bracket.
Secure the bracket with the nuts, flat washers and lock washers provided.
3. Wall Mount Option: Position the bracket on the mounting surface at the desired location and
secure the bracket to the mounting surface using the appropriate hardware (Wall mounting
hardware requirements to be determined and supplied by the end user).
Figure 10 – Pipe Mounting Bracket Secured to a Horizontal or Vertical Flat Pipe and Angle pipe

3.5. Wiring a Transmitter
3.5.1. Loop Power Overview
The transmitter is designed to operate in a two-wire power/current loop with loop resistance and
power supply voltage within the HART operating range shown in Figure 11.
Figure 11 – HART/DE Transmitter Operating Ranges
Loop wiring is connected to the Transmitter by simply attaching the positive (+) and negative (–) loop
wires to the positive (+) and negative (–) terminals on the Transmitter terminal block in the
Electronics Housing. Connect the Loop Power wiring shield to earth ground only at the power supply
end. Note that the Transmitter is not polarity-sensitive.

Figure 12 – Transmitter 9-Screw Terminal Board and Grounding Screw
As shown in Figure 12, each Transmitter has an internal terminal to connect it to earth ground.
Optionally, a ground terminal can be added to the outside of the Electronics Housing. Grounding the
Transmitter for proper operation is required, as doing so tends to minimize the possible effects of
noise on the output signal and affords protection against lightning and static discharge. An optional
lightning terminal block can be installed in place of the non-lightning terminal block for Transmitters
that will be installed in areas that are highly susceptible to lightning strikes. As noted above, the Loop
Power wiring shield should only be connected to earth ground at the power supply end.
Note: Pin 9 is not used.
Wiring must comply with local codes, regulations and ordinances. Grounding may be
required to meet various approval body certification, for example CE conformity. Refer to
Appendix A of this document for details.
Note: Terminal #3 is for loop test
For HART the Transmitter is designed to operate in a two-wire power/current loop with loop
resistance and power supply voltage within the operating range; see Figure 11.
Figure 11. With an optional remote meter, the voltage drop for this must be added to the basic power
supply voltage requirements to determine the required Transmitter voltage (VXMTR) and maximum
loop resistance (RLOOP MAX). Additional consideration is required when selecting intrinsic safety
barriers to ensure that they will supply at least minimum Transmitter voltage (VXMTR MIN), including
the required 250 ohms of resistance (typically within the barriers) needed for digital communications.

Transmitter loop parameters are as follows:
RLOOP MAX = maximum loop resistance (barriers plus wiring) that will allow proper Transmitter
operation and is calculated as RLOOP MAX = (VSUPPLY MIN – VXMTR MIN - VSM)  21.8 mA.
In this calculation:
VXMTR MIN = 11.8 V (HART) VSM = 2.3 V, remote meter
Note that VSM should only be considered if a remote meter will be connected to the transmitter.
The positive and negative loop wires are connected to the positive (+) and negative (–) terminals on
the terminal block in the Transmitter Electronics Housing.
Barriers can be installed per Honeywell’s instructions for Transmitters to be used in intrinsically safe
applications.
3.5.2. Wiring Variations

The above procedures are used to connect power to a Transmitter. For loop wiring, sensor wiring and
external wiring, detailed drawings are provided for Transmitter installation in non-intrinsically safe
areas and for intrinsically safe loops in hazardous area locations.
3.5.3. Loop Wiring Procedure

1. See Figure 12, above, for parts locations. Loosen the end cap lock using a 1.5 mm Allen wrench.
2. Remove the end cap cover from the terminal block end of the Electronics Housing.
3. Feed loop power leads through one end of the conduit entrances on either side of the
Electronics Housing. The Transmitter accepts up to 16 AWG wire.
4. Connect the positive loop power lead to the positive (+) terminal #1 and the negative loop
power lead to the negative (-) terminal #2. Note that the Transmitter is not polarity-sensitive.
5. Feed sensor input wires through the second housing conduit entry and connect wires per
Figure 12.
6. Replace the end cap, and secure it in place.

3.5.4. Grounding and Lightning Protection
Connect a wire from the Earth Ground Clamp or to the Internal Ground Connection (see Figure 12) to
Earth Ground to make the protection effective. Use a size 8 AWG or (8.37mm2) bare or green
covered wire for this connection.
For ungrounded Thermocouple, mV, RTD or ohm inputs connect the input wiring shield(s) to the
Internal Ground Connection shown in Figure 12.
For grounded Thermocouple inputs, connect the Internal Ground Connection shown in Figure 12 to
the same earth ground as used by the thermocouple.
As noted above, the Loop Power wiring shield should only be connected to earth ground at the power
supply end.
3.5.5. Explosion-Proof Conduit Seal
When installed as explosion proof in a Division 1 / Zone 1, Ex d Hazardous Location,

keep covers tight while the Transmitter is energized. Disconnect power to the Transmitter in
the non-hazardous area prior to removing end caps for service.
When installed as non-incendive equipment in a Division 2 hazardous location, disconnect
power to the Transmitter in the non-hazardous area, or determine that the location is non-
hazardous before disconnecting or connecting the Transmitter wires.
Transmitters installed as explosion proof in Class I, Division 1, Group A Hazardous (classified)

locations in accordance with ANSI/NFPA 70, the US National Electrical Code, Canadian Electric
Code CCSAC22.1, with 1/2 inch conduit do not require an explosion-proof seal for installation. If
3/4 inch conduit is used, a LISTED explosion proof seal to be installed in the conduit, within 18
inches (457.2 mm) of the transmitter.
Crouse-Hinds type EYS/EYD or EYSX/EYDX are examples of LISTED explosion proof seals that
meet this requirement. Transmitters installed as explosion proof in Class I, Division 1, Group A, B, C
or D hazardous (classified) locations do not require that explosion proof seal be installed in the
conduit.

3.5.6. Input Sensor Wiring
Connect the input sensors as shown in Figures below:
Figure 13 – STT750 Thermocouple, RTD, mV, ohm and Volt Connections
Figure 13 – STT750 Thermocouple, RTD, mV, ohm and Volt Connections

3.6. Startup
3.6.1. Overview
This section identifies typical start up tasks associated with several generic temperature measurement
applications. It also includes the procedure for running an optional analog output check.
3.6.2. Startup Tasks

After completing the installation and configuration tasks for a Transmitter, you are ready to start up the
process loop. Startup usually includes:
 Setting initial resistance (RTD sensor types only)

 Reading inputs and outputs
 Applying process inputs to the transmitter.
The actual steps in a startup procedure vary based on the type of Transmitter and the measurement
application. In general, the procedures in this section are based on using Honeywell MC Toolkit, with
a HART variant, to check the Transmitter input and output under static process conditions, and make
adjustments as required initiating full operation with the running process.
Note: Checks can be made using the optional three-button assembly, if your Transmitter is so
equipped. Operation with the three-button assembly is discussed in the “Operation” section of this
manual.
3.6.3. Output Check Procedures

The Output Check comprises the following procedures:
 The Loop Test procedure checks for continuity and the condition of components in the output
current loop.
 The Trim DAC Current procedure calibrates the output of the Digital-to-Analog converter for
minimum (0%) and maximum (100%) values of 4 mA and 20 mA, respectively. This
procedure is used for Transmitters operating online in analog mode to ensure proper
operation with associated circuit components (for example, wiring, power supply, control
equipment). Precision test equipment (an ammeter or a voltmeter in parallel with precision
resistor) is required for the Trim DAC Current procedure.
 The Apply Values procedure uses actual Process Variable (PV) input levels for calibrating
the range of a Transmitter. The PV is carefully adjusted to stable minimum and maximum
levels, and the Lower Range Limit Value (LRV) and Upper Range Limit Value (URV) are
then set by commands from the MC Toolkit.
The Transmitter does not measure the given PV input or update the PV output while it
operates in the Output mode.

3.6.4. Constant Current Source Mode Procedure
Figure 14 – Current Loop Test Connections
1. Refer to Figure 14 for test connections. Verify the integrity of electrical components in the output
current loop.
2. Establish communication with the Transmitter. For these procedures, the values of components in
the current loop are not critical if they support reliable communication between the Transmitter
and the Toolkit.
3. On the Toolkit, display the Output Calibration box.
4. In the Output Calibration box, select the Loop Test button; the LOOP TEST box will be
displayed.
5. Select the desired constant-level Output: 0 %, 100 %, or Other (any between 0 % - 100 %).
6. Select the Set button. A box will be displayed asking Are you sure you want to place the
transmitter in output mode?
With the Transmitter in Analog mode, you can observe the output on an externally-
connected meter or on a local meter.
7. Select the Yes button. Observe the output current at the percentage you selected in Step 5.
8. To view the monitor display, navigate back from the LOOP TEST display, and select the
MONITOR display. A Confirm popup will be displayed.
9. Select Yes to continue. This concludes the Startup procedure.

4. Operation
4.1. Overview
This section provides the information and processes involved for HART operation using the 3-button
option.
4.2. Three-Button Operation

The STT750 optional three-button interface is located under the nameplate and provides a user
interface and operation capability without opening the transmitter.
Figure 15 shows the location of the three-button option and the labels for each button.
Figure 15 - Three-Button Option

Table 5 – Three-Button Option Functions
Physical
Display Action
Button
Increment Scroll to previous menu item in an active list.
Left
 Scroll through alphanumeric list to desired character (ex.
Previous Menu Item for entering Tag names or numeric values)
Decrement Scroll to next menu item in an active list.
Center
 Next Menu Item Scroll through alphanumeric list to desired character (ex.
for entering Tag names or numeric values)
Select displayed Call up the menu.
Right menu item for Select an item for data entry.
 activation or editing Confirm a data entry operation
Activate the service associated with a selected menu item.
4.2.1. Menu Navigation

The user must press  button to call up the menu. To exit the menu and return to the PV display
screen, select Exit menu.
Use the  and  buttons to scroll through or wrap around the list of menu items. Press the  button
to select an item for data entry or activation. When an item is selected for data entry or activation, the
cursor will appear on the lower line of the LCD (Display) to allow editing of the value.
No action is taken against a menu item until the  button is pressed.
After a user presses the  button to begin a data entry operation, another button must be pressed
within 10 seconds or data entry will time out and the original value of the parameter will be
preserved.
If no button presses occur within 60 seconds, menu access will time out and the transmitter will exit
the menu and return to the PV display.
4.2.2. Data Entry

Data entry is performed from left to right. Select a character / digit by pressing  or  buttons, and
then press  to advance to the next character position to the right. Select the << character to
terminate the entry or if the final character is already a space character, just press  again.
All numeric entries are clamped at the low or high limit if needed. You can determine the low and
high limit for a parameter by selecting either the H or L character while the cursor is positioned over
the left-most digit and press  button. The Display will show the selected limit.

Table 6 – Three-Button Data Entry
Screen
Numeric data entry Text entry
Symbol
Display the high limit for this parameter.
H This symbol only appears in the left-most Not Available
position of the data entry field.
Display the low limit for this parameter.
L This symbol only appears in the left-most Not Available
position of the data entry field.
<< Terminate the numeric entry Terminate the text entry

0 thru 9, These characters are used to enter
These characters can be used to
Minus, numeric values. The minus sign only
create custom tags and unit labels
Decimal appears in the left-most digit.
A thru Z,
0 thru 9 These characters can be used to
Not Available
special create custom tags and unit labels
symbols
4.2.3. Editing a Numeric Value

Editing a Numeric Value
Editing of a numeric value is a digit-by-digit process, starting with the left-most digit.
1. Press  to begin the edit process.

2. The Display will show the current value of the item on the lower line, left justified.
3. Press the  or  buttons to select the desired digit, and then press  to advance to the next
digit to the right.
4. After the last digit has been entered, press  one more time to write the new value to the
transmitter.
4.2.4. Selecting a new setting from a list of choices

Use the procedure described below to select a new setting for parameters that present a list of choices
(e.g., Screen PV, Screen Units, etc.).
1. Press  to begin the edit process.
a. The Display will show the current setting of the item on the lower line, left justified.
2. Press the  or  buttons to scroll through the list of choices.
3. Press  to make your selection. The new selection will be stored in the transmitter and will
be displayed on the lower line, right justified.

4.2.5. The Display Menu
Table 7 – The Display Menus

'#' in "Screen #" indicates the screen numbers 1, 2, 3, 4, 5, 6, 7, 8
Adjust the LCD contrast level.
Range from » (1) to »»»»»»»»»
LCD Contrast »»»»»
(9)
Default: »»»»»»» (7)
Rotation Time
Enabled Select to enable or disable the
Screen Rotate
Disabled automatic rotation of Screens
Select Screen 1 through 8
Select Screen to configure.
Screen # Select to enable or disable the
Enabled/Disabled
screen for display and configuration
Loop PV
Select the Process Variable (PV)
CJ Temperature
that will be shown on the screen.
Screen # PV Sensor
Sensor Resistance is only available
Resistance
for RTDs and will read 0 for
Loop Output
thermocouples
Percent Output
None
Select the PV decimal resolution to
Screen # Decimal X.X
be shown on selected screen from
X.XX
list.
X.XXX
Screen # Units
Choose appropriate engineering Press ↵ to
(Writable only for °C, °F,°R, K
units from list enter menu
TC/RTD sensor types
only) selection
Range/Cal Units ↑ and ↓ to
°C, °F, °R, K Select the ranging and calibration
(Visible for TC and select entry.
temperature units
RTD sensor type only) ↵ to enter
Sensor Type mV, TC, RTD,
(Database updates Ohm
take 30 seconds to Select Sensor Type.
complete. Do not
interrupt power).
Sensor ID
(Database updates
Select Sensor ID for Input selected
take 30 seconds to Sensor Identifier
Sensor Type (Input selection).
complete. Do not
interrupt power).
Sensor Wire Type
2-Wire, 3-Wire, 4- Select the number of lead wires for
(Visible for RTD and
Wire RTD and Ohm sensors.
Ohm sensor type only)
Sensor Lead Resist
Sensor lead wire resistance value.
(Visible for RTD and ####.##
(only if RTD type is 2 wire)
Ohm sensor type only)
Sensor Bias ####.## Bias on the measured value

Sensor Cal Lo Pt
####.## Calibration low point for Sensor
Press ↵ to
enter menu
Sensor Cal Hi Pt selection
####.## Calibration high point for Sensor
↑ and ↓ to
Executing this selection corrects the select entry.
Do Sensor Cal Lo
Confirm Cal Low Point based on the input ↵ to enter
measurement
Executing this selection corrects the
Do Sensor Cal Hi
Confirm Cal High Point based on the input
measurement
Sensor LRV Lower Range Value representing 0% Read Only
####.##
output Parameter
Sensor URV Upper Range Value representing Read Only
####.##
100% output Parameter
Press ↵ to
enter menu
Executing this selection Resets the selection
Reset Sensor Cal
Confirm LRV, and URV Corrects back to
Factory values ↑ and ↓ to
select entry.
↵ to enter
Sensor CVD
(Applicable for Pt50, Callendar - Van Dusen RTD Read Only
Enabled, Disabled
Pt100, Pt200, Pt500 coefficients for Sensor Parameter
and Pt1000 RTDs only)
Enable or disable detection of Input
Break Detect Enable, Disable
wire break
When enabled, causes all critical
sensor input failures to latch to the
Critical Fault state. The fault may
Latching
Enabled, Disabled only be cleared by device reset.
When disabled, the critical sensor
input failure will be cleared if the
input recovers. Press ↵ to
enter menu
Determines the source of the Cold selection
CJ Type
Internal, Fixed Junction compensation for
thermocouple Sensor types. ↑ and ↓ to
When CJ Type is Fixed, specifies the select entry.
Fixed CJ Value Cold Junction temperature value for ↵ to enter
(Visible for TC input thermocouple Sensor types.
####.##
only) Degrees Celsius. Fixed CJ
temperatures below -50 degrees
have no effect on measured values.
The limits are:
LRV #. ## the Lower Range Limit (LRL) and the
URV #. ## Upper Range Limit (URL) of the
selected Sensor ID

ATTENTION: Executing this service
Set Lower Range will set the Lower Range Value
Set LRV
Value (LRV) equal to the input
measurement
ATTENTION: Executing this service
Set URV Set Upper Range will set the Upper Range Value
Value (URV) equal to the input
measurement
Selection applies digital filtering to
suppress noise effects on the PV.
Damping #. ##
The limits for this value are 0.0 to
32.0 seconds
Disabling sets the loop output and
Enabled
NAMUR Output burnout levels to the Honeywell
Disabled
levels
This selection allows the loop zero
DAC Zero Trim Press ↵ to
output 4mA value to be trimmed.
enter menu
Note: Loop must be DAC Zero Trim selection
Note: You must connect a current
removed from
meter to the transmitter to monitor
Automatic Control ↑ and ↓ to
the loop output.
This selection allows the loop span select entry.
DAC Span Trim output 20mA value to be trimmed. ↵ to enter
Note: Loop must be DAC Span Trim Note: You must connect a current
removed from meter to the transmitter to monitor
Automatic Control the loop output.
This selection allows the user to

force the DAC output to any value
Loop Test between 3.8 and 20.8 mA.
Note: This selection will put the DAC
Loop Test
Note: Loop must be into Fixed Output Mode, as indicated
12.000
removed from by the flashing output value.
Automatic Control Navigation away from this menu item
will return the loop to Normal
(Automatic) Mode.
None
PV High
Alarm Type 1
PV Low Read Only
Type of alarm.
Parameter
Critical Diagnostic
Alarm Type 2 Redundant Input

Active
Enter Tag ID name up to 8
Tag ID  characters long. Tag ID
 = any Alphanumeric value
Unique for each Read Only
HART Device ID Unique ID for device
device Parameter
Units for the Primary Variable
Units of (Writable - for TC/RTD Sensor Type,
HART PV Units
transmitted PV Read only - mV and Ohm Sensor
Type)

Units of
HART SV Units Units for the Secondary Variable Press ↵ to
transmitted SV
This selection allows the user to enter menu
enter the date a transmitter is selection
installed.
The Install Date is entered in ↑ and ↓ to
sequence of Day, Month, and Year, select entry.
followed by the new date and the ↵ to enter
Install Date
DD MM YYYY prompt Write Date to confirm the
entry.
CAUTION: The Install Date can only
be written once in the life of the
Transmitter. You cannot erase or
overwrite the Install Date once it has
been written.
Menu item shows the current
Display
Firmware versions of the Display, Read Only
Firmware Electronics
Electronics Module and the Sensor Parameter
Sensor
Module
Menu item shows the Read Only
Protocol HART
communications protocol Parameter
Identifies the type and range of the Read Only
Model Key
transmitter Parameter
<Exit Menu>

4.3. Three Button Operation with no Display Installed
When there is no Display installed, the buttons can be used to perform a Zero or Span adjustment of
the Transmitter. Caution should be taken to insure these adjustments are only made when the correct
input values are applied.
4.3.1. Zero Adjustment

This adjustment is the same as performing a Set LRV using the Display.
1. Connect a current meter or voltmeter as shown in Figure 14 to monitor the PV output of the
Transmitter.
2. Using an accurate input source, apply a signal equivalent to the Transmitter LRV.
3. Press the Down (↓ ) and Zero (  ) buttons together to set the Zero.
4. Verify that the output is now 4 mA.
4.3.2. Span Adjustment

This adjustment is the same as performing a Set URV using the Display.
1. Connect a current meter or voltmeter as shown in Figure 14 to monitor the PV output of the
Transmitter.
2. Using an accurate input source, apply a signal equivalent to the desired Upper Range Value
of the transmitter.
3. Press the Down (↓) and Span ( ) buttons together to set the span.
4. Verify that the PV output is now 20 mA.
You can also use the MCT 202 and MCT404 Toolkit to make any adjustments to an
STT750 SmartLine Temperature Transmitter.

4.4. Changing the Default Failsafe Direction
For HART the transmitters are shipped with a default failsafe direction of upscale. This means that the
Transmitter output will set the current output to upscale failsafe (maximum output) upon detection of
a critical status. The failsafe direction can be changed from upscale to downscale (minimum output)
by moving the top jumper located in the Electronic module.
The Transmitter electronics module interprets either signal as not-a-number and initiates its own
configured failsafe action for the control system.
4.4.1. Procedure to Establish Failsafe Operation
The failsafe direction display accessible via the Toolkit shows only the state of the
jumper as it correlates to analog Transmitter operation.
The integrated circuits in the Transmitter PWA are vunerable to damage by stray
static discharges when removed from the Electronics Housing. Minimize the possibility of
static discharge damage when handling the PWA as follows:
Do not touch terminals, connectors, component leads, or circuits when handling the PWA.
When removing or installing the PWA, handle it by its edges or bracket section only. If you
need to touch the PWA circuits, be sure you are grounded by staying in contact with a
grounded surface or by wearing a grounded wrist strap.
When the PWA is removed from the Transmitter, put it in an electrically conductive bag, or
wrap it in aluminum foil to protect it.
The following procedure outlines the steps for positioning the write protect and failsafe jumpers on
the electronics module. See Figure 16 for the locations of the failsafe and write protect jumpers.
Figure 16 – Locating the Failsafe and Write Protect Jumpers

Table 8 – HART Failsafe and Write Protect Jumpers
Jumper
Description
Arrangements
Failsafe = UP (High)
Write Protect = OFF (Not Protected)
Failsafe = DOWN (Low)

Write Protect = OFF (Not Protected)
Failsafe = UP (High)
Write Protect = ON (Protected)
Failsafe = DOWN (Low)

Write Protect = On (Protected)
1. Turn OFF Transmitter power (Power removal is only required in accordance with
area safety approvals. Power removal is only required in Class 1 Div 1 Explosion
proof and Class 1 Div 2 environments).
2. Loosen the end cap lock, and unscrew the end cap from the electronics side of the
Transmitter housing.
3. If equipped with a Display module, carefully depress the two tabs on the sides of the
Display Module, and pull it off.
4. If necessary, unplug the interface connector from the Communication module. Do not
discard the connector.
5. Set the Failsafe Jumper (top jumper) to the desired position (UP or DOWN). See
Table 8 and Figure 16 for jumper positioning.
6. If applicable, re-install the Display module as follows:
 Orient the display as desired.
 Install the Interface Connector in the Display module such that it will mate
with the socket for the display in the Communication module.
 Carefully line up the display, and snap it into place. Verify that the two tabs
on the sides of the display latch.
NOTE: Installing a Display Module into a powered transmitter may cause a temporary upset
to the loop output value.
Orient the Display for proper viewing through the end cap window.
You can rotate the meter mounting orientation in 90 o increments.
7. Restore transmitter power if removed.

4.5. Monitoring the Display
This section describes the information shown on the operator screens of the Display.
4.5.1. Display
Figure 17
Figure 17 illustrates the Display format with Process Variable (PV).
 The PV value is user-configurable. This field has 7 characters. The maximum allowable
numeric value is 9999999 or -999999. If fractional decimals are configured, the fractional
positions will be dropped, as required. If the PV value exceeds the above limits, it is divided
by 1000 and “K” is appended to the result, allowing a maximum value with multiplier of
999999K or -99999K.
 Process Variable Tag is user-configurable from a HART Host. This field has 14 characters.
 Engineering Units. This field is user-configurable when measuring temperature.
Figure 17 – Display with Process Variable Format

5. Maintenance
5.1. Overview
This section provides information about preventive maintenance and replacing damaged parts. The
topics covered in this section are:
 Replacement of damaged parts such as the Electronics Modules.
5.2. Preventive Maintenance Practices and Schedules

The STT750 SmartLine Transmitter does not require any specific maintenance at regularly scheduled
intervals.
Maintenance of the STT750 is limited to ensuring that connections, seals and mounting are tight and
secure. There are no moving parts or adjustments and hence no reason to open the field housing
except to inspect for corrosion or conductive dust entry which could later affect reliable operation.
The transmitter modules themselves should never be opened.
5.3. Replacing the Communication Module

The Communication module includes a connector to the optional Display module. This section
includes the procedure to replace the Communication module.
The transmitter does not have to be removed from service to replace the Comm
Module
Please take appropriate steps to avoid ESD damage when handling the
Communication and Display Module assemblies
Refer to Figure 18 for parts locations.
Figure 18 – PWA Replacement

1. Turn OFF Transmitter power (Power removal is only required in accordance with
area safety approvals. Power removal is only required in Class 1 Div 1
Explosionproof and Class 1 Div 2 environments).
 When removing the Communications Module with power applied, the loop
will go to 0V. Likewise, installing a Communications Module into a
transmitter with power applied will cause the loop output value to go to 12 ma
for several seconds then the loop output value will go to the configured value
based on the PV input.
 Installing a Display Module into a powered transmitter may cause a temporary
upset to the loop output value.
2. Loosen the end cap lock, and unscrew the end cap from the electronics side of the
Transmitter housing.
3. If equipped with a Display module, carefully depress the two tabs on the sides of the
Display Module, and pull it off.
4. If necessary, unplug the Display interface connector from the Communication
module. Do not discard the connector.
5. Loosen the two retaining screws, and carefully pull the Communication module from
the Electronics compartment.
6. Carefully, insert the Communication module into the Electronics compartment.
7. Tighten the two Communication module retaining screws.
8. Refer to the SmartLine User's Manual to change the Failsafe and Write Protect
Jumper configuration settings.
9. If applicable, re-install the Display module as follows:
a) Orient the display as desired.
b) Install the Interface Connector in the Display module such that it will mate with the
socket for the display in the Communication module.
c) Carefully line up the display, and snap it into place. Verify that the two tabs on the
sides of the display latch.
Orient the Display for proper viewing through the end cap window.
You can rotate the meter mounting orientation in 90 o increments.
10. Apply Parker Super O-ring Lubricant or equivalent to the end cap O-ring before
installing the end cap. Reinstall the End Cap and tighten the End Cap locking screw.
11. Installing Optional External Configuration Button Assembly.
a) Loosen (Do Not Remove) both top nameplate screws and pivot nameplate 90°.
b) Align the protrusion on the button assembly with the matching opening in the
housing and snap the button assembly into the housing.
c) Rotate the nameplate back to the original position, and tighten the nameplate screws.

(Steps 13 - 16 required for Field Upgrades Only)
12. Loosen the End Cap locking screw and unscrew the End Cap from the Field Wiring
side of the transmitter housing.
13. Select the proper Communication/External Configuration upgrade kit label from the
label strip provided and adhere to the inside of the Field Wiring compartment End
Cap.
14. Apply Parker Super O-ring Lubricant or equivalent to the end cap o-ring before
installing the end cap. Reinstall the End Cap and tighten the end cap locking screw
15. Install external upgrade label (i.e. DEVICE MODIFIED…..) provided on outside of
housing as shown in Figure 18.
16. Restore power if removed.
17. Check the settings of the Transmitter Setup and Display Setup parameters to make
sure that the transmitter is configured correctly for your application. Refer to the
STT750 HART manual (34-TT-25-15) for details on HART transmitters.
18. If applicable, verify External Button Configuration operation.
Installation is complete.

6. Calibration
6.1. Recommendations for Transmitter Calibration
The STT750 SmartLine Temperature Transmitter does not require periodic calibration to maintain
accuracy. Typically, calibration of a process-connected Transmitter will degrade, rather than augment
the capability of a smart Transmitter. For this reason, it is recommended that a Transmitter be
removed from service before calibration. Moreover, calibration must be accomplished in a controlled,
laboratory-type environment, using certified precision equipment.
6.2. Calibration Procedures

For a Transmitter operating in analog mode, you must calibrate its output signal measurement range
using any compatible hand-held communicator or a local display.
One calibration option is to use the Honeywell MC Toolkit (MCT). Refer to the MC Toolkit
(MCT202) User Manual, # 34-ST-25-20 or (MCT404) User Manual, Document # 34-ST-25-50.
Calibration information and procedures for a Transmitter operating in the HART mode are provided
in the STT750 Series HART Option User’s manual, document number 34-TT-25-15, Section on
“Calibration.”

7. Troubleshooting
7.1. Overview
Troubleshooting involves responding to error messages, primarily displayed by the MC Toolkit. Error
messages that may occur on the Transmitter’s local display are fairly self-explanatory and intuitive.
However, this section covers the diagnostic messages that indicate critical conditions. Other than the
critical conditions, additional detail is not provided. If you require assistance, contact your distributor
or Honeywell Technical Support. All other messages are covered by the MC Toolkit Users’ Manual.
7.2. Critical Diagnostics Screens
When a Critical Diagnostic is present in the Transmitter, the Display will display the message
CRITICAL FAULT on the top line of the LCD and the appropriate diagnostic text on the lower line.
7.2.1. Fault Conditions and Recommended Corrective Actions
Table 9 – Fault Conditions and Recommended Corrective Actions.

Recommended Corrective
Condtion Analysis
Action
Electronics Module Use a HART communicator to read the Cycle power to the
Fault. detailed status information from the transmitter.
A critical failure has transmitter. Refer to the appropriate If the problem continues to
been detected on the communicator manual for more occur replace the Electronics
HART Electronics information about the possible failure Module.
Module. causes.
Temperature Sensor Use a HART communicator to read the If the diagnostic status
Module Fault. detailed status information from the indicates an input problem
A critical failure has transmitter. Refer to the appropriate (burnout, out of range, etc.),
been detected on the communicator manual for more correct the root error and then
Temperature Sensor information about the possible failure cycle power to the transmitter.
Module. causes. If the problem continues to
occur replace the
Temperature Sensor Module.
Temperature Sensor Use a HART communicator to read the Cycle power to the
Comm Fault. detailed status information from the transmitter.
Cannot communicate transmitter. Refer to the appropriate If the problem continues to
with the Temperature communicator manual for more occur replace the
Sensor Module. information about the possible failure Temperature Sensor Module
causes.

8. Parts List
8.1. Overview
Individually saleable parts for the various Transmitter models are listed in this section. Some parts are
illustrated for identification. Parts are identified and listed in the corresponding tables as follows:
 Individually saleable parts are indicated in each figure by key number callout.
 Parts that are supplied in kits are indicated in each illustration by key number callout with the
letter K prefix.
Table 10 is a summarized list of recommended spare parts.
Table 10 – Summary List of Recommended Spare Parts

10-
Key 1-10
Part Number Description Figure No. 100
No. Units
Units
Electronics Housing Assembly
50098718-501 HART Electronics Module Without REED
Sensor PWA
Figure 21 5 1 1-2
50098718-502 HART Electronics Module With REED Sensor
PWA
50049911-502 Display Module Figure 20 4 1 1-2
50086421-501 HART Temperature/Terminal Block Assy

Without Lightning Protection, Single Input
Figure 21 3 1 1
50086421-503 HART Temperature/Terminal Block Assy With
Lightning Protection, Single Input

Figure 19 – Pipe and Wall Bracket Parts
Flat Pipe Mounting Bracket Carbon Steel

Flat Pipe Mounting Bracket 316 SS
Marine Approved Mounting Bracket 316 SS
Wall Mounting Bracket Carbon Steel
Wall Mounting Bracket 316 SS
Angle Pipe Mounting Bracket Carbon Steel
Angle Pipe Mounting Bracket 316 SS

Table 11 – Pipe and Wall Bracket Parts
(Refer to
Figure 19)
Qty
Key
Part Number Description Per
No.
Unit
1 50090524-501 Carbon Steel Flat Pipe Bracket Mounting kit for all models 1
2 50090524-503 316 Stainless Steel Flat Pipe Bracket Mounting kit for all models 1
3 50092363-501 Carbon Steel Wall Bracket Mounting kit for all models 1
4 50092363-503 316 Stainless Steel Wall Bracket Mounting kit for all models 1
5 30752770-007 Carbon Steel Angle Pipe Bracket Mounting kit for all models 1
6 30752770-407 316 Stainless Steel Angle Pipe Bracket Mounting kit for all models 1
Figure 20 – Electronic Housing, Display End
Table 12 – Transmitter Major Assemblies

(Refer to Figure 20, Figure 21)
Key Quantity
Part Number Description
No. Per Unit
50049858-501 End Cap (Aluminum) 1
1 50049858-521 End Cap (Stainless Steel)
50049832-501 End Cap, Display (Aluminum) 1
2 50049832-521 End Cap, Display (Stainless Steel)
50086421-501 HART Temperature/Terminal Block Assy Without Lightning 1

Protection, Single Input
3
50086421-503 HART Temperature/Terminal Block Assy With Lightning
Protection, Single Input

50049911-502 Display for Temperature 1
4
5 50086423—501 HART Electronics Module Assembly (PWA) without Reed sensor

1
50086423--502 HART Electronics Module Assembly (PWA) with Reed sensor
6 50049915-501 External Zero, Span & Config Buttons (HART) 1
K1 30757503-005 Electronics housing seals kit (includes O-rings)
Figure 21 – Electronic Housing, Terminal Block End

Appendix A. PRODUCT CERTIFICATIONS
A1. Safety Instrumented Systems (SIS) Installations

For Safety Certified Installations, please refer to STT 850/750 Safety Manual 34-TT-25-05 for
installation procedure and system requirements.
A2. European Directive Information (EU)

A3. Hazardous Locations Certifications
MSG AGENCY TYPE OF PROTECTION COMM Electrical Ambient
CODE OPTION Parameters Temperature
Explosion proof, Certificate:
FM16US0157X:
Class I, Division 1, Groups A, B,
C, D;
T5: Ta= -50oC
Dust Ignition Proof:
to 85oC
Class II, III, Division 1, Groups 4-20 mA/
T6: Ta= -50oC
E, F, G; T6..T5 DE/HART/ FF/ Note 1
to 65oC
PROFIBUS
Class 1, Zone 1, AEx d IIC
T6..T5 Gb
Class 2, Zone 21, AEx tb IIIC T
95oC IP 66 Db
Intrinsically Safe, Certificate:

FM16US0157X:
Class I, II, III, Division 1, Groups
A, B, C,
D, E, F, G; T4 4-20 mA/ -50oC to 70oC
DE/HART Note 2
FM
Class I Zone 0 AEx ia IIC T4 Ga /FF/ PROFIBUS
A Approvals TM
FISCO Field Device (Only for FF
(USA)
Option)
Ex ia IIC T4
Non-Incendive, Certificate:
FM16US0157X:
Class I, Division 2, Groups A, B, 4-20 mA/
-50oC to 85oC
C, D; T4 DE/HART Note 1
Class I Zone 2 AEx nA IIC T4 Gc /FF/ PROFIBUS
AEx nA IIC T4
Standards: FM 3600:2011; ANSI/ ISA 60079-0: 2013

FM 3615:2006; ANSI/ ISA 60079-1 : 2015
FM 3616 : 2011 ; ANSI/ ISA 60079-31 : 2015
FM 3610:2010; ANSI/ ISA 60079-11 : 2014
FM 3810 : 2005 ; FM 3611:2004; ANSI/ ISA 60079-15 : 2012 ;
FM 3810 : 2005 ; NEMA 250 : 2003 ; ANSI/ IEC 60529 : 2004
Enclosure: Type 4X/ IP66/ IP67 ALL ALL ALL

Explosion proof, Certificate:
2689056:
Class I, Division 1, Groups A, B,
C, D;
Dust Ignition Proof:
4-20 mA/
Class II, III, Division 1, Groups Note 1 -50oC to 85oC
DE/HART/FF
E, F, G; T4
Zone 1 Ex d IIC T4 Gb
Ex tb IIIC T 95oC IP 66 Db
DIP A21 Class II, III
Intrinsically Safe, Certificate:
2689056:
Class I, II, III, Division 1, Groups
A, B, C,
D, E, F, G; T4 4-20 mA/
Note 2 -50oC to 70oC
DE/HART/FF
Ex ia IIC T4 Ga
FISCO Field Device (Only for FF
Option)
Ex ia IIC T4
Non-Incendive, Certificate:
2689056:
B CSA-Canada Class I, Division 2, Groups A, B,
4-20 mA/
C, D; T4 Note 1 -50oC to 85oC
DE/HART/FF
Class I Zone 2 Ex nA IIC T4 Gc
Ex nA IIC T4 Gc
Enclosure: Type 4X/ IP66/ IP67 ALL ALL ALL
Standards:
CSA C22.2 No. 0-10; CSA 22.2 No. 25-1966 (reaffirmed 2009);
CSA C22.2 No. 30-M1986 (reaffirmed 2012); CSA C22.2 No. 94-M91;
CSA C22.2 No. 142-M1987 (reaffirmed 2009); CSA-C22.2No.157-92 (reaffirmed
2012);
C22.2 No. 213-M1987(reaffirmed 2012); C22.2 No. 60529-05
C22.2 No. CSA 60079-0:2011; C22.2 No. 60079-1: 2011; C22.2 No. 60079-11:
2011;
C22.2 No. 60079-15: 2012; C22.2 No. 60079-31: 2012;
ANSI/ ISA12.12.01-2012; ANSI/ ISA 60079-0 (12.00.01): 2009 ;

ANSI/ ISA 60079-1 (12.22.01): 2009 ; ANSI/ ISA 60079-11(12.02.01) : 2012;
ANSI/ ISA 60079-26 (12.00.03) : 2011; ANSI/ ISA 60079-15(12.12.02) : 2012 ;
ANSI/ ISA 60079-27 (12.02.04) : 2006; ANSI/ ISA 60079-31(12.10.03) : 2009 ;
FM Class 3615: Aug 2006; FM Class 3616: Dec 2011; ANSI/ IEC 60529 : Edition 2.1
ANSI/ UL 913: Edition 7; ANSI/ UL 916 : Edition 4 ;

Flameproof, Sira 14ATEX2046X:
4-20 mA/
II 2 G Ex d IIC T4 Gb Note 1 -50oC to 85oC
DE/HART/FF
II 2 D Ex tb IIIC T 95oC Db IP 66/ IP67
Intrinsically Safe, Sira 14ATEX2046X:
-50oC to 70oC
II 1 G Ex ia IIC T4 Ga
4-20 mA/
FISCO Field Device (Only for FF Note 2
DE/HART/FF FISCO:
Option)
-50oC to 45oC
Ex ia IIC T4
C ATEX Enclosure: IP66/ IP67 ALL ALL ALL
Standards: EN 60079-0: 2012; EN 60079-1 : 2007; EN 60079-31 : 2009
EN 60079-11: 2011; EN 60079-26 : 2006; EN 60529 : 2000 + A1
Non Sparking, Sira 14ATEX4052X: 4-20 mA/

II 3 G Ex nA IIC T4 Gc Note 1 -50oC to 85oC
DE/HART/FF
Enclosure: IP66/ IP67 ALL ALL ALL
Standards: EN 60079-0: 2012; EN 60079-15 : 2010; IEC 60529 : 2009 with Corr 3
Flameproof, SIR 14.0020X

4-20 mA/
Ex d IIC T4 Gb Note 1 -50oC to 85oC
DE/HART/FF
Ex tb IIIC T 95oC IP 66/ IP67
Intrinsically Safe, SIR 14.0020X
Ex ia IIC T4 Ga -50oC to 70oC
4-20 mA/
FISCO Field Device (Only for FF Note 2 FISCO:
DE/HART/ FF
Option) -50oC to 45oC
Ex ia IIC T4
D IECEx Non Sparking, SIR 14.0020X 4-20 mA/
Ex nA IIC T4 Gc Note 1 -50oC to 85oC
DE/HART/ FF
Standards: IEC 60079-0: 2011, Edition 6; IEC 60079-1 : 2007-04, Edition 6;
IEC 60079-11 : 2011, Edition 6; IEC 60079-15 : 2010, Edition 4
IEC 60079-26 : 2006, Edition 2; IEC 60079-31 : 2008, Edition 1
IEC 60529 : 2009 with Corr 3
Flameproof:
4-20 mA/
DE/HART/FF
Intrinsically Safe:
Ex ia IIC T4 Ga
SAEx 4-20 mA/
FISCO Field Device (Only for FF Note 2 -50oC to 70oC
E (South DE/HART/FF
Option)
Africa)
Ex ia IIC T4
Non Sparking: 4-20 mA/
DE/HART/FF

Flameproof:
4-20 mA/
DE/HART/FF
Intrinsically Safe:
Ex ia IIC T4 Ga 4-20 mA/
F INMETRO Note 2 -50oC to 70oC
FISCO Field Device (Only for FF Option) DE/HART/FF
Ex ia IIC T4
Non Sparking: 4-20 mA/
DE/HART/FF
Flameproof:
4-20 mA/
DE/HART/FF
Ex tb IIIC T 85oC IP 66
Intrinsically Safe:
Ex ia IIC T4 4-20 mA/
NEPSI Note 2 -50oC to 70oC
G FISCO Field Device (Only for FF Option) DE/HART/FF
(CHINA) Ex ia IIC T4
Non Sparking:
4-20 mA/
Ex nA IIC T4 Note 1 -50oC to 85oC
DE/HART/FF
H KOSHA Flameproof:
(KOREA) 4-20 mA/
DE/HART/FF
Ex tD A21 T 95oC IP 66/ IP67
Intrinsically Safe:
Ex ia IIC T4 4-20 mA/
Note 2 -50oC to 70oC
FISCO Field Device (Only for FF Option) DE/HART/FF
Ex ia IIC T4
J EAC Ex Flameproof:
(Russia, 4-20 mA/
1 Ex d IIC T4 Gb Note 1 -50oC to 85oC
Belarus and DE/HART/FF
Ex tb IIIC T95oC Db
Kazakhstan)
Intrinsically Safe:
0 Ex ia IIC T4 Ga -50oC to 70oC
4-20 mA/
Ex ia IIIC T4 Db Note 2 FISCO:
DE/HART/FF
FISCO Field Device (Only for FF Option) -50oC to 45oC
0 Ex ia IIC T4
Non Sparking:
4-20 mA/
2 Ex nAc IIC T4 Note 1 -50oC to 85oC
DE/HART/FF

Notes
1. Operating Parameters:
4-20 mA/HART (Loop Terminal)
Voltage= 11 to 42 V Current= 4-20 mA Normal (3.8 – 23 mA Faults)
2. Intrinsically Safe Entity Parameters

For details see Control Drawing on page 51 of the User’s manual
SIL 2/3 IEC 61508 SIL 2 for non-redundant use and SIL 3 for redundant use according to
Certification EXIDA and TÜV Nord Sys Tec GmbH & Co. KG under the following standards:
IEC61508-1: 2010; IEC 61508-2: 2010; IEC61508-3: 2010.
MID Approval Issued by NMi Certin B.V. in accordance with WELMEC guide 8.8, OIML R117.1
Edition 2007 (E), and EN 12405-1+A2 Edition 2006. Applicable to Pt100 sensor only.
MARINE TYPE Lloyd’s Register Certificate Number: 16/60011

APPROVAL Environmental categories ENV1, ENV2, ENV3 and ENV5 as defined in Lloyd’s
Register Test Specification No. 1, February 2015

A4. Marking ATEX Directive
General:
The following information is provided as part of the labeling of the transmitter:
• Name and Address of the manufacturer
• Notified Body identification: DEKRA Quality B.V., Arnhem, the Netherlands
• For complete model number, see the Model Selection Guide for the particular model of
Temperature Transmitter.
• The serial number of the transmitter is located on the Housing data-plate. The first two
digits of the serial number identify the year (02) and the second two digits identify the week
of the year (23); for example, 0223xxxxxxxx indicates that the product was manufactured in
2002, in the 23rd week.
Apparatus Marked with Multiple Types of Protection

The user must determine the type of protection required for installation the equipment. The
user shall then check the box [] adjacent to the type of protection used on the equipment
certification nameplate. Once a type of protection has been checked on the nameplate, the
equipment shall not then be reinstalled using any of the other certification types.
WARNINGS and Cautions:

Intrinsically Safe and Non-Incendive Equipment:
WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR USE IN
HAZARDOUS LOCATIONS.
Explosion-Proof/ Flameproof:
WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT
Non-Incendive Equipment:
WARNING: DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAYBE PRESENT
All Protective Measures:

WARNING: FOR CONNECTION IN AMBIENTS ABOVE 60oC USE WIRE RATED 105oC

A.5 Conditions of Use” for Ex Equipment”, Hazardous
Location Equipment or “Schedule of Limitations”:
Consult the manufacturer for dimensional information on the flameproof joints for repair.
Painted surface of the STT750 may store electrostatic charge and become a source of
ignition in applications with a low relative humidity less than approximately30% relative
humidity where the painted surface is relatively free of surface contamination such as dirt,
dust or oil. Cleaning of the painted surface should only be done with a damp cloth.
Intrinsically Safe: Must be installed per drawing 50091227
Division 2: This equipment is suitable for use in a Class I, Division 2, Groups A, B, C, D; T4 or

Non-Hazardous Locations Only.
The installer shall provide transient over-voltage protection external to the equipment such
that the voltage at the supply terminal of the equipment does not exceed 140% of the
voltage rating of the equipment.
The enclosure is manufactured from low copper aluminium alloy. In rare cases, ignition
sources due to impact and friction sparks could occur. This shall be considered during
Installation, particularly if equipment is installed a Zone 0 location.
If a charge-generating mechanism is present, the exposed metallic part on the enclosure is

capable of storing a level of electrostatic that could become incendive for IIC gases.
Therefore, the user/ installer shall implement precautions to prevent the buildup of
electrostatic charge, e.g. earthing the metallic part. This is particularly important if
equipment is installed a Zone 0 location.

A.6 Control Drawing
Note: DE, FF and PA do not apply to STT750

9. Appendix B – Security
8.2. How to report security vulnerability
For the purpose of submission, a security vulnerability is defined as a software defect or weakness
that can be exploited to reduce the operational or security capabilities of the software or device.
Honeywell investigates all reports of security vulnerabilities affecting Honeywell products and
services.
To report potential security vulnerability against any Honeywell product, please follow the
instructions at:
https://honeywell.com/pages/vulnerabilityreporting.aspx
Submit the requested information to Honeywell using one of the following methods:
• Send an email to security@honeywell.com.
Or
• Contact your local Honeywell Process Solutions Customer Contact Centre (CCC) or Honeywell
Technical Assistance Centre (TAC) listed in the “Support and Contact information” section of this
document.

Glossary
AWG American Wire Gauge

CVD Callendar-Van Dusen is an equation that describe the relationship
between resistance (R) and temperature (t) of platinum resistance
thermometers (RTD)
EMI Electromagnetic Interference
FTA Field Termination Assembly
Hz Hertz
LRL Lower Range Limit
LRV Lower Range Value
mAdc Milliamperes Direct Current
mV millivolts
Nm Newton.meters
NVM Non-Volatile Memory
PM Process Manager
PV Process Variable
PWA Printed Wiring Assembly
RFI Radio Frequency Interference
RTD Resistance Temperature Detector
T/C Thermocouple
URL Upper Range Limit
URV Upper Range Value
US Universal Station
Vac Volts Alternating Current
Vdc Volts Direct Current

Index
A I
About This Manual ..................................... iii Input Sensor Wiring .................................. 17
Accuracy .....................................................5 Installation and Startup...............................7
Application Design ......................................5 Display Installation Precautions ................................ 7
Mounting STT750 Temperature Transmitters ........... 7
Site evaluation ........................................................... 7
B Installation Site Evaluation
Bracket Mounting ..................................... 12 Site Evaluation ........................................................... 7
Introduction ...............................................1
C
M
Calibration Procedures .............................. 34
Changing the Default Failsafe Direction ..... 28 Maintenance ............................................ 31
Failsafe Operation ....................................................28 Preventive Maintenance Practices and Schedules .. 31
Replacing the Communication Module ................... 31
Copyrights, Notices and Trademarks ............ii
MCToolkit ...................................................7
Monitoring the Display ............................. 30
D
Monitoring the Displays
Diagnostic Messages ...................................5 Display ..................................................................... 30
Display Installation Precautions...................7 Mounting Dimensions ............................... 10
Display Options...........................................4 Mounting STT 750 Temperature Transmitters
...............................................................8
E Bracket Mounting Procedure .................................. 12
Mounting Dimentsions .............................................. 8
Explosion-Proof Conduit Seal .................... 16 Summary ................................................................... 8
F N
Features and Options ..................................1 Name Plate .................................................3
Functional Characteristics ..........................................2
Physical Characteristics ..............................................1 O
G Operation ................................................. 20
Changing the Default Failsafe Direction .................. 28
Glossary.................................................... 58 Three Button Operation with no Display Installed .. 27
Three-Button Operation .......................................... 20
Grounding and Lightning Protection .......... 16
Optional 3-Button Assembly........................4
H
P
Honeywell MC Toolkit .................................7
Parts List ................................................... 36
Patent Notice............................................. iv
PRODUCT CERTIFICATIONS ........................ 40

R T
References................................................. iv Telephone and Email Contacts.................... iv
Release Information................................... iii Three Button Operation with no Display
Installed ................................................ 27
S Span Adjustments ................................................... 27
Zero Adjustments .................................................... 27
Safety .........................................................5 Three-Button Operation ............................ 20
Accuracy ..................................................................... 5 Data Entry................................................................ 21
Diagnosis Messages ................................................... 5 Display menu ........................................................... 23
Safety Certification .....................................3 Editing a Numeric Value .......................................... 22
Startup ..................................................... 18 Menu Navigation ..................................................... 21
Constant Current Source Mode Procedure .............. 19 Transmitter Adjustments ............................3
Output Check Procedures ........................................ 18 Transmitter Calibration ............................. 34
Support and Contact Information ............... iv Troubleshooting ....................................... 35
Symbol Descriptions and Definitions ........... v Critical Diagnostics Screens ..................................... 35
W
Wiring a Transmitter ................................. 13
Wiring Procedure .................................................... 15
Wiring Variations ..................................................... 15

Sales and Service
For application assistance, current specifications, pricing, or name of the nearest Authorized Distributor, contact one of
the offices below.
ASIA PACIFIC EMEA AMERICA’S

Honeywell Process Solutions, Honeywell Process Solutions, Honeywell Process Solutions,
(TAC) hfs-tac-support@honeywell.com Phone: + 80012026455 or Phone: (TAC) 1-800-423-9883 or
+44 (0)1344 656000 215/641-3610
Australia (Sales) 1-800-343-0228
Honeywell Limited Email: (Sales)
Phone: +(61) 7-3846 1255 FP-Sales-Apps@Honeywell.com Email: (Sales)
FAX: +(61) 7-3840 6481
Toll Free 1300-36-39-36 or FP-Sales-Apps@Honeywell.com
Toll Free Fax: (TAC) or
1300-36-04-70 hfs-tac-support@honeywell.com (TAC)
hfs-tac-support@honeywell.com
China – PRC - Shanghai
Honeywell China Inc.
Phone: (86-21) 5257-4568
Fax: (86-21) 6237-2826
Singapore
Honeywell Pte Ltd.
Phone: +(65) 6580 3278
Fax: +(65) 6445-3033
South Korea
Honeywell Korea Co Ltd
Phone: +(822) 799 6114
Fax: +(822) 792 9015

For more information
To learn more about SmartLine Transmitters,
visit www.honeywellprocess.com
Or contact your Honeywell Account Manager
Process Solutions
Honeywell
1250 W Sam Houston Pkwy S
Houston, TX 77042
Honeywell Control Systems Ltd

Honeywell House, Skimped Hill Lane
Bracknell, England, RG12 1EB
Shanghai City Centre, 100 Jungi Road
Shanghai, China 20061
34-TT-25-13, Rev.4
September 2017
www.honeywellprocess.com 2017 Honeywell International Inc.

34 TT 25 13 STT750 Manual

Uploaded by

Copyright:

Available Formats

34 TT 25 13 STT750 Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

34 TT 25 13 STT750 Manual

Uploaded by

Copyright:

Available Formats

STT750 SmartLine

Honeywell Process Solutions

© Copyright 2017 by Honeywell, Inc.

Honeywell Process Solutions

Page ii STT750 Temperature Transmitter User’s Manual Revision 4

To digitally integrate a Transmitter with one of the following systems:

STT750 SmartLine Temperature Transmitter User Manual, Document # 34-TT-25-13,

Revision 4 STT750 Temperature Transmitter User’s Manual Page iii

STT750 SmartLine Temperature Transmitter Quick Start Installation Guide, Document

Support and Contact Information

Honeywell Corporate www.honeywellprocess.com

Honeywell Process Solutions https://www.honeywellprocess.com/smartline-temperature/

Training Classes http://www.automationccollege.com

Telephone and Email Contacts

Area Organization Phone Number

Page iv STT750 Temperature Transmitter User’s Manual Revision 4

ATTENTION: Identifies information that requires special consideration.

CAUTION: Indicates a potentially hazardous situation which, if not avoided,

WARNING: Indicates a potentially hazardous situation, which, if not avoided,

WARNING, Risk of electrical shock: Potential shock hazard where

ESD HAZARD: Danger of an electro-static discharge to which equipment may

Protective Earth (PE) terminal: Provided for connection of the protective

Functional earth terminal: Used for non-safety purposes such as noise

Earth Ground: Functional earth connection. NOTE: This connection shall be

Chassis Ground: Identifies a connection to the chassis or frame of the

Revision 4 STT750 Temperature Transmitter User’s Manual Page v

Page vi STT750 Temperature Transmitter User’s Manual Revision 4

Revision 4 STT750 Temperature Transmitter User’s Manual Page vii

Page viii STT750 Temperature Transmitter User’s Manual Revision 4

Figure 1 – STT750 Major Assemblies ................................................................................................... 2

Revision 4 STT750 Temperature Transmitter User’s Manual Page ix

Table 1 – Features and Options.............................................................................................................. 1

Page x STT750 Temperature Transmitter User’s Manual Revision 4

1.2. Features and Options

Table 1 – Features and Options

Feature/Option Standard/Available Options

1.2.1. Physical Characteristics

Revision 4 STT750 Temperature Transmitter User’s Manual Page 1

Figure 1 – STT750 Major Assemblies

Figure 2 – Electronics Housing Components

1.2.2. Functional Characteristics

Page 2 STT750 Temperature Transmitter User’s Manual Revision 4

Figure 3 –Typical STT750 Nameplate

1.4. Safety Certification Information

1.5. Transmitter Adjustments

Revision 4 STT750 Temperature Transmitter User’s Manual Page 3

Table 2 – Available Display Characteristics

1.7. Optional 3-Button Assembly

 Increment, decrement, and enter key functions.

Page 4 STT750 Temperature Transmitter User’s Manual Revision 4

2.2.2. Diagnostic Messages

Revision 4 STT750 Temperature Transmitter User’s Manual Page 5

Table 4 – STT750 Standard Non-Critical Diagnostics Messages

Non-Critical Diagnostics (Warning Conditions)

Page 6 STT750 Temperature Transmitter User’s Manual Revision 4

3.2. Honeywell MC Toolkit

3.3. Display Installation Precautions

Revision 4 STT750 Temperature Transmitter User’s Manual Page 7

Figure 4 – STT750 with adapter housing - Horizontal Wall Mounting