Schramm T660H Manual

SCHRAMM LIMITED WARRANTY
Schramm, Inc. ("Schramm") warrants that this limited to V-belts, electrical bulbs, wiper blades,
Schramm machine or equipment is free of defects filters, lubricants, and batteries. This limited war-
in material and workmanship at the time of ship- ranty does not apply to normal maintenance ser-
ment from our factory. This warranty is subject to vice and adjustments, including, but not limited to
the following limitations. fuel, air and hydraulic system cleaning, engine
tune-up, clutch inspection and adjustment.
1.This limited warranty applies only to the original
user/customer and only to machines and equip- 6.1t shall be the obligation of the user/customer to
ment which have been subjected to normal use and pay for transportation of this machine or equipment
service. to the dealer providing warranty service and to pay
for travel time or mileage if warranty service is
2.This limited warranty is for a period of 12 months: provided at the job site.
from initial operation or 2000 hours, whichever
occurs first; not to exceed 18 months from the date 7. Unless notified in writing by Schramm, Inc. all
of shipment except as follows: replaced parts must be returned to Schramm, Inc.,
New Rotary Screw Compressors - 24 months transportation charges prepaid.
from shipment or 4000 hours, whichever occurs
first. 8. In order for this limited warranty to apply, this
machine or equipment must be made available for
PneumaGophers - 6 months from shipment or repair during the warranty period.
1000 hours, whichever occurs first.
Spare Parts - 6 months from shipment or 1000 9. Schramm, Inc. shall not be liable for defects,
hours, whichever occurs first. damages or failures caused by unauthorized al-
terations, use of non-approved parts, unreasonable
Remanufactured Schramm Products - (Except use, neglect, abuse, accident, or negligent repair,
Rotary Screws) - 3 months from shipment or 500 including a failure to provide reasonable and neces-
hours, whichever occurs first. sary maintenance after the new machine is in
Remanufactured Rotary Screw Compressors - service.
One year from shipment or 2000 hours, whichever
occurs first. 10. Schramm, Inc. reserves the right to make
design changes or any product improvement at any
3. Schramm's obligation under this limited war- time, without incurring any obligation to install same
ranty shall be solely to replace or repair without on units previously manufactured.
charge at the dealer's location those component
parts which Schramm itself manufactured, and only 11. There are no warranties, express or implied,
if such component parts were defective when the other than the limited warranty, as set forth above,
machine or equipment was shipped from and this limited warranty supersedes any warranty,;,...
Schramm's factory. Any component part installed promises or representations previously made or-
to replace a defective component part is warranted issued. THERE ARE ABSOLUTELY NO IMPLIED
solely for the duration of the unexpired warranty on WARRANTIES OF MERCHANTABILITY OR OF
the machine or equipment in which such a com- FITNESS FOR A PARTICULAR PURPOSE and
ponent part is installed. Schramm hereby excludes all such warranties
which might otherwise be implied by law.
4. This machine or equipment may incorporate
many component parts manufactured by com- 12. Schramm's liability for breach of this limited
panies other than Schramm, such as truck chassis, warranty, whether a claim or lawsuit is drought in
carriers, tracks, engines, tires, hydraulic pumps, contract, tort or strict liability, shall be limited
hydraulic motors and other component parts too exclusively to repair or replacement of defective
numerous to list. This limited warranty does not parts manufactured by Schramm. Schramm shall
apply to such component parts, but such com- not be liable for any direct or indirect incidental or
ponent parts may be warranted by the companies consequential damages of any kind which may
'that manufactured them. result from defects in its products or from breach of
this limited warranty nor shall Schramm be liable for
5. This limited warranty does not apply to regular any damages resulting from a user/customer's loss
maintenance replacement items. including but not of use of this Schramm machine or equipment.
1/1:88
SCHRAMM FIELD REPORT
for suggestions and claims.
This form must be completely filled out by you, describe fully what happened. You can also use this form
DESCRIPTION MODEL NO. SERIAL NO.
NO.
,!
CUSTOMER NAME AND ADDRESS TERR. DATE

DEALER OR OFFICE
DEALER
DATE SHIPPED FROM W.C. HOW LONG IN SERVICE
2 -7 I fa IT f\A VA s-r- I OP et-trei , Ids 269 i‘o w

£r. 34ectiMS 3 2, S /46 H
SIGNED '
IPHAD SAME COMPLAINT ON SAME ITEM
• YES • NO.
Itnecessary, use reverse side fiolidditionat comments or sketches.
0 • Fax (215) 696.6950
SCHRAMM, INC. • 800 E Virginia Ave. • West Chester, PA 19380 • Phone: (215) 696-250
SA-894(12/871
0256G 3/88
ROTADRILL T660H PARTS MANUAL
Main Frame Components Chapter 1
Engine, Heat Exchanger And Pump Gearbox Drive Components Chapter 2
Compressor And Air Line Circuit Chapter 3
Control Panel, Hydraulic Circuits And Hydraulic Pumps Chapter 4
Mast And Rotation Gearbox Components Chapter 5
Component Breakdown Chapter 6
Accessories Chapter 7
Schematics Chapter 8
0256G
INDEX
Page No.
Chapter 1 Main Frame Components
Rear Outrigger 1-1

Front Outrigger 1-3
:Tool Box . • 1-5
Batteries 1-7
.Fuel Tank 1-9
Work Platform And Pipe Storage Rack 1-11
Chapter 2 Engine, Heat Exchanger And Pump Gearbox

Drive Components
Deck Engine Service Components 2-1

(Muffler, Belts, And Filters)
Miscellaneous Engine Parts 2-2
Fuel Filters 2-4
Engine Frame 2-6
Heat Exchanger And Hydraulic Oil Cooler 2-8
Engine Air Cleaner 2-11
Pump Gearbox Drive Material 2-13
Radiator Fan Drive 2-15
Chapter 3 Compressor And Air Line Circuit
Compressor Service Components 3-1

Air Valve 3-2
Air-041 Tank Group 3-5
Comp'ressor Clutch Group 3-9
Clutch Control 3-12
Compressor Air Cleaner 3-14
Scavenger Line And Control Line Filters 3-16
Compressor Air Delivery Control 3-18
Compressor And Air Selector Valves 3-20
Compressor Oil Filters 3-22
Compressor Connections 3-25
Compressor Air Intake 3-27
thApter 4 Control Panel, Hydraulic Circuits And

Hydraulic Pumps
Control Panel - Engine 4-1

Control Panel - Drilling Functions 4-3
Operator Platform 4-5
Helpers Platform 4-7
0256G

INDEX
Page No.
Chapter 4 Control Panel, Hydraulic Circuits And

Hydraulic Pumps (Con'd.)
Outrigger Circuit 4-9

Breakout Wrench Circuit 4-12
Winch Circuit (With Braden PD5.8 Winch). . . . 4-14
Winch Circuit (With Gear Products PG105 Winch) 4-16
Mast Tilt Cylinder Circuit 4-19
Rotation Gearbox Circuit 4-21
Traverse Cylinder Circuit 4-24
Rotation Direction Control (CMX) Valve Circuit 4-26
Rapid Feed Circuit 4-28
Water Injection Circuit 4-30
Water And Foam Injection Pump Asy. (10 GPM) 4-33
Lubricator, On-Off Valve And Metering Valve 4-37
Hydraulic Tank Connections 4-39
Hydraulic Return Manifold And Thermal Control Valve. . 4-41
Slow Feed Circuit 4-43
Downfeed Regulator 4-45
Holdback Regulator 4-47
Hydraulic Pumps And Pump Gearbox 4-49
Chapter 5 Mast And Rotation Gearbox Components
Mast Assembly - Top (Chain, Sprockets, Etc.) 5-1

Mast Assembly - Bottom (Dust Diverter Asy, Guide Slips,. 5-4
Mast Pivot Bearing Asy, Etc.)
Rotation Gearbox Assembly 5-7
Pipe Wrench 5-11
Pipe Handling Sling 5-13
Chapter 6 Component Breakdown
Breakout Cylinder - Swing Cylinder (Opt. Jib Boom) 6-1

Feed Cylinder 6-3
Outrigger Cylinder 6-5
Mast Tilt Cylinder 6-7
Lazy Susan Swing Cylinder 6-9
Lazy Susan Lock Pin Cylinder 6-11
Jib Boom Extension Cylinder (With Lazy Susan) 6-13
Jib Boom Extension Cylinder (Without Lazy Susan) • • • • 6-15'
Pressure Lubricator 6-17
Rotation Gearbox Directional Control Valve 6-19'
Minimum Pressure Valve 6-21
0256G
ROTADRILL 1660H PARTS MANUAL

INDEX
Page No.
•
Chapter 7 Accessories
Jib Boom - Top Of Mast (Standard - Single Line Pulley) 7-1

Lazy Susan Assembly 7-3
Jib Boom Hydraulic Circuit 7-7
Lazy Susan Hydraulic Circuit 7-9
Floating Sub 7-12
Chapter 8 Schematics
Electrical System Schematic Drawing 0859-0114

Hydraulic System Schematic Drawing 3861-0127
•
0359G 3/88
ALPHABETICAL INDEX
Page No.
Air Valve 3-2

Air-Oil Tank Group 3-5
Batteries 1-8
Breakout Cylinder - Swing Cylinder (Opt. Jib Boom) . 6-1
Breakout Wrench Circuit 4-12
Clutch Control 3-12

Compressor Air Cleaner 3-14
Compressor Air Delivery Control 3-18
Compressor Air Intake 3-27
Compressor And Air Selector Valves 3-20
Compressor Clutch Group 3-9
Compressor Connections 3-25
Compressor Oil Filters 3-22
Compressor Service Components 3-1
Control Panel - Drilling Functions 4-3
Control Panel - Engine 4-1
Deck Engine Service Components 2-1

(Muffler, Belts, And Filters)
Downfeed Regulator 4-45
Electrical System Schematic Drawing 0859-0114

Engine Air Cleaner 2-11
Engine Frame 2-6
Feed Cylinder 6-3

Floating Sub 7-12
Front Outrigger 1-4
Fuel Filters 2-4
Fuel Tank 1-10
Heat Exchanger And Hydraulic Oil Cooler 2-8

Helpers Platform 4-7
Holdback Regulator 4-47
Hydraulic Pumps And Pump Gearbox 4-49
Hydraulic Return Manifold And Thermal Control Valve. 4-41
Hydraulic System Schematic Drawing 3861-0127
Hydraulic Tank Connections 4-39
Jib Boom - Top Of Mast (Standard - Single Line Pulley) 7-1

Jib Boom Extension Cylinder (With Lazy Susan) 6-13
Jib Boom Extension Cylinder (Without Lazy Susan) . . . 6-15
Jib Boom Hydraulic Circuit 7-7
3/88
0359G
ALPHABETICAL INDEX
Page No.
Lazy Susan Assembly 7-3

Lazy Susan Hydraulic Circuit 7-9
Lazy Susan Lock Pin Cylinder 6-11
Lazy Susan Swing Cylinder 6-9
Lubricator, On-Off Valve And Metering Valve. . 4-37
Mast Assembly - Bottom (Dust Diverter Asy, Guide Slips, 5-4

Mast Pivot Bearing Asy, Etc.)
Mast Assembly - Top (Chain, Sprockets, Etc;) . . . .. . 5-1
Mast Tilt Cylinder 6-7
Mast Tilt Cylinder Circuit 4-19
Minimum Pressure Valve 6-21
Miscellaneous Engine Parts 2-2
Operator Platform 4-5

Outrigger Circuit 4-9
Outrigger Cylinder 6-5
Pipe Handling Sling 5-13

Pipe Wrench 5-11
Pressure Lubricator 6-17
Pump Gearbox Drive Material 2-13
Radiator Fan Drive 2-15

Rapid Feed Circuit 4-28
Rear Outrigger 1-2
Rotation Direction Control (CMX) Valve Circuit 4-26
Rotation Gearbox Assembly 5-7
Rotation Gearbox Circuit 4-21
Rotation Gearbox Directional Control Valve 6-19
Scavenger Line And Control Line Filters 3-16

Slow Feed Circuit 4-43
Tool Box 1-6

Traverse Cylinder Circuit 4-24
Water And Foam Injection Pump Asy. (10 GPM) 4-33

Water Injection Circuit 4-30
Winch Circuit (With Braden PD5.8 Winch) 4-14
Winch Circuit (With Gear Products PG105 Winch) 4-16
Work Platform And Pipe Storage Rack 1-12
•
4
REAR OUTRIGGER
10
1-1
0331G 3/88
REAR OUTRIGGER
REF. NO.
NO. PART NUMBER DESCRIPTION RE Q
1 2813-0201 CYLINDER, HYD (4 x 2 x 41) 2

2 0480-0037 COVER ASY, MAST PIVOT SUPPORT 2
3 9S01-0037 CAPSCREW (3/8 x 1) 4
4 9W03-0006 LOCKWASHER (3/8) 4
5 9W02-0004 PLATEWASHER (3/8 SAE) 4
6 3175-0032 FOOT, OUTRIGGER 2
7 0293-0254 FRAME, SUB (W/MAST PIVOT) 1
8 2825-0011 PIN (1-5/8 x 9-5/8) 2
9 9C01-0025 PIN, COTTER (1/4 x 2-1/2) 4
10 3178-0003 PIN (1-5/8 x 8-7/8) 2
SCHRAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

NUMBER WHEN ORDERING PARTS.
Printed in U.S.A.
1-2
FRONT OUTRIGGER
1-3
0332G 3/88
FRONT OUTRIGGER
REF. NO.
NO. PART NUMBER DESCRIPTHION REQ.
1 3193-0044 SUPPORT, OUTRIGGER & MAST CRADLE 1

2 2825-0011 PIN (1-5/8 x 9-5/8) 1
3 9C01-0025 PIN, COTTER (1/4 x 2-1/2) 4
4 9S01-0071 CAPSCREW (1/2 x 1-1/4) 2
5 9W03-0008 LOCKWASHER (1/2) 2
6 0480-0114 COVER, FRONT OUTRIGGER 1
8 3178-0003 PIN (1-5/8 x 8-7/8) 1
9 2813-0201 CYLINDER, HYD (4 x 2 x 41) 1
10 3175-0032 FOOT, OUTRIGGER 1
11 3193-0029 SUPPORT, OUTRIGGER 1
12 3583-0028 ANGLE (4 x 4 x 3/4 x 32) 1
13 3583-0027 ANGLE (4 x 4 x 1/2 x 34-5/8) 1
14 0978-0203 CAPSCREW, (5/8NF x 2-3/4 - SAE GRADE 8) 6
0570-0094 WASHER, HT (1-1/4 x 7/64 x 21/32) 6
15
0374-0023 LOCKNUT (5/8 NF) 6
16
ALWAYS GIVE EQUIPMENT SERIAL

SCHRAMM, INC., West Chester, PA
Printed In U.S.A. 1-4
TOOL BOX
/
//
9
10
0
14
13
12
1-5
0257G 3/88
TOOL BOX
REF. NO.
NO. PART NUMBER DESCRIPTION REQ.
0749-0032 BOX, TOOL 1

1 1
2 2966-0057 DOOR, TOOL BOX
9501-0021 CAPSCREW (5/16 x 1) 8
3
LOCKNUT (5/16) 8
4 0374-0032
0180-0052 LATCH, BAIL HEAD 2
5 6
6 9501-0072 CAPSCREW (1/2 x 1-1/2)
WASHER, BEVELED (1/2) 6
7 0570-0013 6
8 9W02-0006 PLATEWASHER (1/2 SAE)
LOCKWASHER (1/2) 6
9 9W03-0008 6
10 9N01-0011 NUT (1/2)
PADLOCK (W/CHAIN) 1
11 0096-0001
9S21-0028 SCREW, PHILLIPS (1/4 x 3/4) 1
12 1
13 9W03-0004 LOCKWASHER (1/4)
NUT (1/4) 1
14 9N01-0007

NUMBER WHEN ORDERING PARTS
rinted in U.S.A.
1-6
BATTERIES
TO CONTROL GROUND
PANEL PRIME TO STARTER
SWITCH POST
TO STARTER
SOLENOID
10
1-7
0289G 3/88
BATTERIES
REF. NO.
NO. PART NUMBER DESCRIPTION REQ
1 0159-0012 SUPPORT, BATTERY (WELDED TO DECK) 1

2 0964-0005 COVER, BATTERY BOX 1
3 0351-0009 CABLE, GROUND (3 GA. x 8", 3/8" - 9/16") 1
4 9E01-0003 CABLE, BLACK DURAVIN (12 GA. x 178") 1
5 2004-0004 BATTERY (6 VOLTS) 4
6 0353-0002 CABLE, BATTERY (1 GA. x 8" N-P 1/2") 3
7 0352-0015 CABLE, BATTERY (0 GA. x 85" N 1/2") 1
8 0350-0012 CABLE, BATTERY (1 GA. x 85" P 1/2") 1
9 0746-0016 FASTENER, BATTERY BOX 2
10 0746-0006 CATCH, FASTENER 2

Printed in U.S.A.
1-8
FUEL TANK
TO TERMINAL STRIP
IN FUSE BOX
22
28 29
27 30
3
ENGINE FUEL
26 RETURN
TO ENGINE
FUEL FILTE
35
13
12
24
31
23
1-9
0308G 3/88
FUEL TANK
REF. NO.
PART NUMBER DESCRIPTION REQ.
NO.
1 0211-0053 TANK, FUEL (180 GAL) 1

2 0978-0026 CAPSCREW (5/8 x 1-3/4) 4
4 9W03-0010 LOCKWASHER (5/8) 4
5 9N01-0013 NUT (5/8) 4
6 0958-0001 GAUGE, FUEL LEVEL 1
7 3337-0024 NIPPLE, X-HVY DS (3/4P x 2-1/2) 1
8 9P05-0022 ELBOW, 90° SERVICE (3/4MP x 3/4FP) 1
9 2249-0003 VALVE, GLOBE BR (3/4P) 2
11 9P07-0032 TEE, SERVICE (3/4MP x 3/4FP x 3/4FP) 2
12 9P08-0054 NIPPLE, CLOSE (3/4P) 2
13 2250-0062 VALVE, CHECK (3/4P) 1
14 9P08-0058 NIPPLE (3/4P x 3) 1
15 9P05-0021 ELBOW, 90° (3/4FP x 3/4FP) 1
16 3332-0045 CONNECTOR (3/4MP X 1/2M37) 1
17 3337-0022 NIPPLE, REDUCING DS (3/4MP x 1/2MP) 1
18 9W03-0004 LOCKWASHER (1/4) 1
19 2250-0006 VALVE, CHECK (1/2P) 1
20 9P01-0006 BUSHING, REDUCING (1/2MP x 1/4FP) 1
21 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 4
22 0079-0003 PUMP, FUEL (Carter # P4594) 1
23 9S01-0036 CAPSCREW, (3/8 x 3/4) 8
24 9W03-0006 LOCKWASHER (3/8) 8
25 9P02-0003 CAP, PIPE (3/4P) 1
26 2904-0017 STANDPIPE FUEL TANK ASY 1
28 9P08-0014 NIPPLE (1/4P x 3) 1
29 9P05-0007 ELBOW, 90° (1/4FP x 1/4FP) 1
30 3332-0026 CONNECTOR (1/4MP X 1/4M37) 1
31 0896-0131 GUARD, FUEL TANK VALVE 1
32 9N01-0007 NUT (1/4) 1
33 2826-0440 HOSE, HYD 1/4 x 30 100R1 37S 2
34 2826-0902 HOSE, HYD 1/4 x 130 100R1 37S 1
35 2826-0484 HOSE, HYD 1/2 x 112 100R2 37S 1

Printed in U.S.A.
1-10
WORK PLATFORM AND PIPE STORAGE RACK
14
0312G 3/88
WORK PLATFORM AND PIPE STORAGE RACK
REF. NO.
1 0211-0053 TANK, FUEL (180 GAL) 1

2 0978-0026 CAPSCREW (5/8 x 1-3/4 - SAE GRADE 5) 4
4 9W03-0010 LOCKWASHER (5/8) 4
5 9N01-0013 NUT (5/8) 4
6 0301-0002 CAP, GASOLINE TANK 1
7 0898-0110 PLATFORM, OPERATOR 1
8 9S01-0108 CAPSCREW, (5/8 x 4) 2
10 0374-0019 LOCKNUT (5/8) 2
11 0213-0038 RETAINER, PLATFORM (WELDED TO TANK) 2
12 0914-0144 PIN, SPRING BALL (5/8 x 3-1/8) 2
13 9M09-0003 CHAIN, BULL DOG #2 2'
14 9S01-0007 CAPSCREW (1/4 x 1) 4
15 9W01-0003 PLATEWASHER (1/4) 4
16 0374-0003 LOCKNUT (1/4) 2
17 0877-0816 SUPPORT, PIPE RACK 1
18 3562-0048 BLOCK, MOUNTING (WELDED TO SUB FRAME) 3
19 2429-0120 SUPPORT, ANGLE (WELDED TO PIPE RACK) 3
20 9S01-0098 CAPSCREW (5/8 x 1-1/2) 9
21 9W03-0010 LOCKWASHER (5/8) 9
22 9W01-0008 PLATEWASHER (5/8) 9
23 9W03-0004 LOCKWASHER (1/4) 2
24 9N01-0007 NUT (1/4) 2

Printed in U.S.A.
1-12
i
•
J/ UV
0320G
DECK ENGINE SERVICE COMPONENTS
(GM 8V92TA ENG)
NO.
REF. DESCRIPTION REG.
PART NUMBER
NO.
3
- 0997-0137 BELTS, FAN (Gates # 9580)
(1/2" x 58-1/4" AUTOMOTIVE V-BELT) 1
SET
- 5000-6198 BELTS, ALTERNATOR (GM # 5101500 - 2 BELTS PER
(3/8" x 47" AUTOMOTIVE V-BELT) 1
- 0731-0022 FAN, 40" SUCTION GM # 5142041-C) 1
FS1213)
- 2299-0012 FILTER, ENGINE FUEL PRIMARY (Fleetguard # 1
- 2299-0004 FILTER, ENGINE FUEL SECONDARY (AC # TP916) 1
- 0277-0032 FILTER, ENGINE OIL (AC # PF911) 1
8-1042)
- 5000-9608 FILTER, ENGINE AIR PRIMARY (Donaldson # SMP1
OR
(Donaldson # XLP18-2042)
P12-8408) 1
- 5000-7894 FILTER, ENGINE AIR SECONDARY (Donaldson # 1
- 0129-0048 MUFFLER (ATI # 2608) 3
- 0383-0005 CLAMP, MUFFLER 1
- 2897-0004 CAP, EXHAUST 1
- 0949-0008 ELBOW, EXH PIPE (5 x 12 OD x ID) 1
- 0923-0046 CABLE, CONTROL 12 FT (THROTTLE) 1
- 0691-0005 BRACKET, THROTTLE 1
- 0488-0005 JOINT, BALL 1
- 1170-0003 SOLENOID, SHUT-DOWN 24 VOLT (ENGINE STOP) 1
- 3068-0001 FLUID, ENGINE STARTING CYLINDER REPLACEMENT 1
- 1153-0176 LOOM AND WIRE ASY (ENGINE TO JUNCTION BOX)

SCHRAIVIM, INC., West Chester, PA NUMBER WHEN ORDERING PARTS.
MISCELLANEOUS ENGINE PARTS
26
28
22
19
18
21
0914;14:2
2-2
3/88
031%
MISCELLANEOUS ENGINE PARTS
NO.
REF. DESCRIPTION REQ.
PART NUMBER
NO.
1
1 2600-0048 ENGINE, DIESEL (8V92TA) 1
2 0129-0048 MUFFLER 1
ING EYE)
3 0862 -0267 BRACKET, MUFFLER (WELDED TO ENGINE LIFT 1
4 0991 -0116 ADAPTOR, EXHAUST 1
5 5000 -5653 CLAMP, TURBOCHARGER (5 IN.) 1
6 0949 -000 8 ELBOW, EXH PIPE (5 x 12 OD x ID) 2
7 0383 -000 5 CLAMP, MUFFLER 1
8 0556 -002 8 CLAMP, HOSE (9-7/8 - 10-3/4) 1
9 2897 -000 4 CAP, EXHAUST PIPE 1
10 3337 -000 4 NIPPLE, DS X-HVY (1/4P x 2) 1
11 9P07-0002 TEE (1/4FP x 1/4FP x 1/4FP) 2
13 2144-0002 SWITCH, NORM CLOSE (7 PSI) 1
14 2158-0003 SENDING UNIT, OIL PRESSURE 1
15 9P01 -0013 BUSHING, REDUCING (3/4MP x 1/2FP) 1
16 9P05 -0016 ELBOW, 90° SERVICE (1/2MP x 1/2FP) 1
17 2826 -0106 HOSE, HYD 1/2 x 42 100R2 NPT 1
18 2220 -0018 CONNECTOR (1/2MP x 1/2FPS) 1
19 0061 -000 6 COUPLING, OIL PAN DRAIN LINE 1
20 0648 -000 1 GASKET, OIL PLUG 1
21 0647-0003 PLUG, OIL DRAIN 2
22 0992-0001 COCK, DRAIN 2
23 9H09-0056 HOSE, RADIATOR (1-1/4 x 36) 2
24 0556-0004 CLAMP, HOSE (.813 x 1.75) 2
25 0577-0021 CLIP, TUBING 1
26 3063-0005 ENGINE KIT, COLD START ENT 1
27 3068-0001 FLUID, ENGINE STARTING CYLINDER REPLACEM 1
28 0923-0046 CABLE, CONTROL 12 FT (THROTTLE) 1
29 0488-0005 JOINT, BALL 1
30 0691-0005 BRACKET, THROTTLE 1
SENDING UNIT, TEMP (100-280)
_ ,- 2159-0002
31 ;x
SWITCH, TEMP-WATER-CLOSE (220 F)
1
32 2145-0010 1
33 2147-0004 SWITCH, TIME DELAY RELAY 1
34 0190 -0014 BRACKET, TIME DELAY SWITCH 2
35 9S01 -003 8 SCREW, MCH PH RD (8/32 x 2) 2
36 9W03 -000 3 LOCKWASHER (8/32) 2
37 9N01 -000 3 NUT (8/32) 4
38 9501 -003 6 CAPSCREW (3/8 x 3/4) 4
39 9W03 -000 6 LOCKWASHER (3/8) 1
40 2134 -001 0 RELAY, SPST N/O (24 VDC) 1
41 0668 -001 3 BRACKET, MOUNTING RELAY 2
42 9501 -000 6 CAPSCREW (1/4 x 3/4) 2
43 0374-0003 LOCKNUT (1/4) 1
44 2022-0021 DAMPENER, VIBRATION RELAY 1
45 0277 -0032 FILTER, ENGINE OIL (AC # PF911)
..,- 7
-._

SCHRAMM, INC., West Chester, PA NUMBER WHEN ORDERING PARTS.
Printed in U.S.A. 2-3
FUEL FILTERS - ENGINE
TO FUEL •
PUMP
05 3
2
TO INJECTORS
FROM FUEL
PUMP
I2
3
5
TO INJECTORS
*
*PRIMARY
FILTER
FROM FUEL
TANK
* ITEMS SUPPLIED
WITH ENGINE
* S ECONDARY
FILTER
2-4
3/88
0322G
FUEL FILTERS - DECK ENGINE
NO.
REF. DESCRIPTION RECL
NO.
PART NUMBER
1
1 3052-0007 BRACKET, FUEL FILTER 3
2 9501-0037 CAPSCREW (3/8 x 1) 7
3 9W03-0006 LOCKWASHER (3/8) 4
4 9S01-0041 CAPSCREW (3/8 x 2) 4
5 9N01-0009 NUT (3/8) 1
6 9P09-0005 PLUG SQ HD (3/8MP) 1
8 3332-0080 CONNECTOR (3/8MP x 1/2M37) 1
9 2826-0484 HOSE, HYD 1/2 x 112 100R2 37S 1
11 2144-0016 SWITCH, PRESSURE N/0 SET (10 PSI) 1
12 2299-0012 FILTER, FUEL PRIMARY (Fleetguard # FS1213) 1
13 2299-0004 FILTER, FUEL SECONDARY (AC # TP916)

SCHRAMM, INC., West Chester, PA NUMBER WHEN ORDERING PARTS
ENGINE FRAME
•
2-6
3/88
0330G ENGINE FRAME
NO.
REF. DESCRIPTION REO.
PART NUMBER
NO.
1
0293-0252 FRAME, ENG-COMP T660H 2
r—N M ictUl
0877-0340 SUPPORT, FLYWHEEL HSG 16

0978-0035 CAPSCREW (5/8 x 2 - SAE GRADE 5) 18
9W03-0010 LOCKWASHER (5/8) 6
0978-0203 CAPSCREW (5/8 x 2-3/4 - SAE GRADE 5) 6
9NO2-0007 NUT (5/8) 8
1•••• CO
0374-0019 LOCKNUT (5/8)
AL
ALWAYS GIVE EQUIPMENT SERI
S
SCHRAMM, INC., West Chester, PA NUMBER WHEN ORDERING PART
52 •
BOLT TO ENGINE
53 LIFTING EYE 1. 50
52 19 20
55 48
54
21 52
24 51
52
52 le
51 •
IN •
42
13
59
58
59
r)
co 56
HEAT EXCHA NGER & HYDRA ULIC OIL COOLER
57
14 58
16 59
17
10
II TO HYD• OIL
THERMOSTAT
12
TO HYD.
MANIFOLD.
• •
0350G 3/88
HEAT EXCHANGER AND HYDRAULIC OIL COOLER
NO.
REF. DESCRIPTION
NO. PART NUMBER REO.
1 0373-0033 COOLER, OIL 1

Consisting of:
COOLER, OIL 1
PACKAGE, MOUNTING 1
2 9S01-0029 CAPSCREW (5/16 x 3) 4

4 9W03-0005 LOCKWASHER (5/16) 14
5 9N01-0008 NUT (5/16) 14
6 2558-0012 BUSHING, REDUCING DS (1-1/4MP x 3/4FP) 2
3877-0017 ELBOW, 90° (3/4MP x 3/4M37) 2
7
3893-0005 ELBOW, 45° (3/4F37 x 3/4M37) 1
8
2826-0631 HOSE, HYD 3/4 x 76 100R2 375 1
9
2826-0017 HOSE, HYD 3/4 x 70 100R2 37S 1
10
0665-0062 GUARD, RADIATOR 1
11
9S01-0023 CAPSCREW (5/16 x 1-1/2) 10
12
0670-0070 RAD & COMP OIL COOLER ASY 1
13
2022-0011 DAMPENER, VIBRATION 4
14
15
0570-0069 PLATEWASHER (3.00 x .25 x .69) 4
16
0374-0019 LOCKNUT (5/8) 4
17 4
18 9W01-0008 PLATEWASHER (5/8)
BRACE, RADIATOR 1
19 0757-0020
SPACER, RADIATOR BRACE 1
20 0822-0158
9501-0071 CAPSCREW (1/2 x 1-1/4) 1
21
9501-0072 CAPSCREW (1/2 x 1-1/2) 1
22
9W01-0007 PLATEWASHER (1/2) 2
23
9W03-0008 LOCKWASHER (1/2) 2
24
9N01-0011 NUT (1/2) 1
25
3343-0006 TEE, DS (3/4FP x 3/4FP x 3/4FP) 1
26
2558-0005 BUSHING, REDUCING DS (3/4MP x 1/4FP) 1
27
28 2144-0011 SWITCH, LOW WATER DETECTOR 1
ELBOW, 45° (3/4MP x 3/4FPS) 1
29 2221-0033
2220-0019 CONNECTOR (3/4MP x 3/4FPS) 1
30 1
31 2826-0160 HOSE, HYD 3/4 x 60 100R2 NPT
CONNECTOR, MALE (3/8MP x 3/8T NYLON) 1
32 2170-0023
TUBING, NYLON (3/8 OD x .075 WALL) 7'
33 9Y02-0018
SHROUD, RADIATOR 1
34 0676-0060
GROMMET, RUBBER (7/16 ID) 1
35 2021-0011
CAPSCREW (5/16 x 3/4) 10
36 9S01-0019 13
37 9W03-0005 LOCKWASHER (5/16)
PLATEWASHER (5/16 SAE) 13
38 9W02-0003
CLIP, HOOD BRACE 1
39 0356-0005
CAPSCREW (5/1 6 x 1/2) 1
40 9S01-0017 1
41 1021-0044 GUARD, WIRE RADIATOR FAN
CAPSCREW (3/8 x 3/4) 8
42 9501-0036 8
43 9W03-0006 LOCKWASHER (3/8)
PLATEWASHER (3/8) 8
44 9W02-0004 2
45 0356-0028 CLIP, FAN GUARD

Printed in U.S.A.
2-9
0350G 3/88
HEAT EXCHANGER AND HYDRAULIC OIL COOLER
REF. NO.
46 9501-0021 CAPSCREW (5/16 x 1) 2

47 9N01-0008 NUT (5/16) 2
48. 2164-0019 ELBOW, 90° (1/4MP x 3/8T NYLON) 1
49 0682-0058 FITTING, RADIATOR INLET 2
50 0992-0002 COCK, DRAIN (1/4P) 2
51 9H09-0053 HOSE, RADIATOR (2-1/4 x 4) 4
52 0556-0008 CLAMP, HOSE (2.313 - 3.250) 10
53 0877-0366 SUPPORT, RADIATOR INLET TUBE 1
54 9501-0037 CAPSCREW (3/8 x 1) 1
55 9W03-0006 LOCKWASHER (3/8) 1
56 0590-0043 FITTING, RADIATOR OUTLET 1
57 0992-0006 COCK, DRAIN (1/2P) 1
58 9H09-0057 HOSE, RADIATOR (3 x 4) 2
59 0556-0009 CLAMP, HOSE (3.063 - 4.000) 4

Printed In U S.A. NUMBER WHEN ORDERING PARTS.
2-10
•
ENGINE AIR CLEANER
TO ENGINE
AIR INTAKE
2-11
3/88
0297G
ENGINE AIR CLEANER
REF. NO.
NO.
1
1 0378-0111 CLEANER, AIR (Donaldson # STG16-1018) 1
)
2 5000-9607 ELEMENT, PRIMARY XLP (Donaldson # P18-2042
alds on # P18- 1042 )
3 5000-9608 ELEMENT, PRIMARY SMP (Don
ELEMENT, SAFETY (Donalds on # P12- 8408 )
4 5000-7894 2
5 0378-0098 BAND, AIR CLEANER MOUNTING (16) 4
6 9S01-0061 CAPSCREW (7/16 x 1-1/4) 4
7 9W01-0006 PLATEWASHER (7/16) 4
8 9W03-0007 LOCKWASHER (7/16) 4
9 9N01-0010 NUT (7/16) 1
10 0877-0823 SUPPORT, AIR CLEANER 4
11 9S01-0071 CAPSCREW (1 /2 x 1-1 /4) 4
12 9W02-0006 PLATEWASHER (1 /2 SAE) 4
13 9W03-0008 LOCKWASHER (1/2) 1
14 2020-0021 ADAPTOR, HOSE REDUCER (8 TO 5.5) 2
15 0556-0027 CLAMP, HOSE (8.375 TO 9.250) 1
16 0823-0045 TUBE, CONNECTOR (5-1 /2 DIA.) 6
17 0556-0013 CLAMP, HOSE (5.625 TO 6.500) 1
18 2020-0045 ADAPTOR, HOSE REDUCER (5.5 TO 5) 1
19 2077-0003 GAUGE ASY, VACUUM 1
20 9P05-0002 ELBOW, 90° (1/8FP x 1/8FP) 2
21 2018-0013 NIPPLE, HOSE (1/4H x 1/8MP) 5'
22 9H01-0001 HOSE, AIR (1/4)

• INC., West Chester,
PA
2-12
U.S
PUMP GEARBOX DRIVE MATERIAL.
ti: ENGINE
20 PULLEY
12 Iz
11 7t c
grte 10 fr
etta.
¢91
2-13
0311G 3/88
PUMP GEARBOX DRIVE MATERIAL
REF. NO.
PART NUMBER DESCRIPTION REQ
NO.
1 1040-0025 GEARBOX, TRIPLE PUMP DRIVE 1

(Funk Specification # 1067613)
2 5000-7027 DIPSTICK (Funk # 4028580) 1
3 0877-0521 SUPPORT, FUNK GEARBOX (LH) 1
4 0925-0008 PLATE, LINE-UP 2
5 0978-0002 CAPSCREW (5/8 x 1-1 /2 - SAE GRADE 5) 8
6 0224-0002 WASHER, HEAD STUD (5/8) 8
7 0978-0186 CAPSCREW (3/4 x 3 - SAE GRADE 5) 4
8 0570-0032 WASHER, HT (1-5/16 x 1/8 x 25/32) 4
9 0570-0108 WASHER (1-1/2 x 1-1/2 x 49/64) 4
10 9P05-0016 ELBOW, 90° SERVICE (1 /2MP x 1/2FP) 1
11 9P08-0043 NIPPLE (1 /2P x 4) 1
12 9P05-0015 ELBOW 90° (1/2FP x 1/2FP) 1
14 5000-8306 BREATHER 1
15 0697-0095 COUPLING, FLANGE E70 (GEARBOX) 1
16 0978-0196 CAPSCREW (1/2NFx 2 - SAE GRADE 8) 4
17 9W03-0008 LOCKWASHER (1/2) 4
(TORQUE 40 LBS-FT. LOCTITE 242)
19 0224-0001 WASHER, HEAD STUD (1/2) 4
20 0697-0039 COUPLING, FLEX ELEMENT (Rex # E70) 1
21 0877-0520 SUPPORT, FUNK GEARBOX (RH) 1
22 0555-0037 SHIM (.030 x 3-1/2 x 7-1/4) (AS REQUIRED) -
23 0555-0039 SHIM (.120 x 3-1 /2 x 7-1/4) (AS REQUIRED) -
24 0555-0038 SHIM (.060 x 3-1/2 x 7-1/4) (AS REQUIRED) -
25 0374-0021 LOCKNUT (3/4) 4
SCHRAMM,INC.,WestOxister,PA ALWAYS GIVE EQUIPMENT SERIAL

Printed in U.S.A.
2-14
RADIATOR FAN DRIVE
k C. 'I/
34 /FAN DRIVE
MATERIAL
2-15
3/88
0327G
RADIATOR FAN DRIVE
NO.
REF. DESCRIPTION
PART NUMBER REQ.
NO.
1
1 0731-0022 BLADE, FAN (8-BLADES, 40" SUCTION)
1
2 0732-0010 HUB ASY, RADIATOR FAN DRIVE
Consisting of: 1
3 0732-0009 HUB, RADIATOR FAN 2
4 2336-0006 BEARING, CUP 1
5 0886-0074 SEAL, OIL 1
6 0733-0002 SPINDLE, RADIATOR FAN 2
7 2335-0006 BEARING, CONE 1
8 0270-0026 WASHER, BRG. LOCK (W-09) 1
9 0374-0038 LOCKNUT (N-09) 1
10 0318-0012 RETAINER, OIL SEAL 1
11 0886-0075 SEAL, OIL 6
12 9W03-0005 LOCKWASHER (5/16) 6
13 9501-0022 CAPSCREW (5/16 x 1-1/4) 1
14 2212-0001 FITTING, GREASE (1/8P) 1
15 0048-0010 KEY, DRIVE (5/16" SQ. x 1-1/2")
1
16 3218-0011 SUPPORT, FAN HUB 6
17 0978-0085 CAPSCREW (1 /2 x 1-1/2 - SAE GRADE 5) 6
18 0224-0001 WASHER, HEAD STUD (1 /2) 8
20 9W03-0010 LOCKWASHER (5/8) 4
21 9N01-0013 NUT (5/8) 1
22 0821-0033 GUARD, FAN DRIVESHAFT 1
23 0896-0132 GUARD, BELT 2
24 9S01-0036 CAPSCREW (3/8 x 3/4) 6
26 9W03-0008 LOCKWASHER (1/2)
1
27 3490-0018 JOINT, UNIVERSAL
Consisting of: 1
28 3199-0006 YOKE, FLANGE 1
29 3199-0016 YOKE, END 2
30 5000-3308 BEARING KIT
5) 4
31 0978-0003 CAPSCREW (7/16 x 1-1/4 - SAE GRADE 4
32 9W03-0007 LOCKWASHER (7/16) 1
33 9S35-0006 SETSCREW, ALLEN (3/8 x 3/8) 1
34 0991-0076 ADAPTER, U-JOINT 6
35 9W02-0004 PLATEWASHER (3/8) 6
36 9W03-0006 LOCKWASHER (3/8) 4
37 9S01-0004 CAPSCREW (1/4 x 1/2) 4
38 9W03-0004 LOCKWASHER (1/4) 4
39 9501-0039 CAPSCREW (3/8 x 1-1/2) 4
40 9N01-0009 NUT (3/8)
• ALWAYS GIVE EQUIPMENT SERIAL

Printed in U.S.A.
2-16
•
•
0329G
3/88
COMPRESSOR SERVICE COMPONENTS
REF.
NO. PART NUMBER NO.
DESCRIPTION
REO.
- 3998-0012 ELEMENT, OIL SEPARATOR

- 2295-0020 FILTER, COMPRESSOR OIL (LEFT SIDE)
3
Schroeder # K10 ELEMENT 10 MICRON
- 2295-0021 FILTER, COMPRESSOR OIL (REUSABLE ELEMENTS)
2
Schroeder # KM-60 STAINLESS STEEL ELEMENT
- 5000-7205 FILTER, COALESCING ELEMENT (Finite # 4C10-050)
- 5000-4284 1
FILTER, COMPRESSOR AIR PRIMARY
1
Donaldson # SMP18-1041
- 5000-4285 FILTER, COMPRESSOR AIR SAFETY (Donaldson # P11-9370)
5000-5137 1
SERVICE KIT, SERVO CYLINDER (Hoerbiger # 90-559232)
1

Printed in U.S.A. NUMBER WHEN ORDERING PARTS.
3-1
AIR VALVE
TO MAST
52 oat.
,I3roo ° 54 SLOWDOWN
.0 ................49**I
51 a 11
1
%to
rvir•
srese TO LUBE
O sea
rrs 23 NEEDLE VALVE
20 21 22 ;WI) %Al III
') oliihr 400 410
6
24 25 2•-- 27 59 ' eirj
7 32 011 11) 41" L VALVE
a0 TO FOAM BAL
34 Milra 100
26
28 tp. vit
0 58
61 24 00 VIE int I219" 0
43
42 501/4
lir 25
V 61
V 60
33 TO WA
ER
17
48 I TO WATER INJ. GAUGE
,/ 62
114" PUMP
FROM AIR 39 ee"
OIL TANK 38 .-- "S •r 6
Osti f:42 45
N 40 42 'Oa
0
141 43
53 '410/KooKorealir----
hoi
0
36 44
6
10
15
Mir 14
11
12 13 16
19 1 56 V I8
57 55
.E3s
17 1°
REG ULAVTOR
RBO
4
keui
66
a 65
•
NE 63. 64
BASUM
TO P/LI 55 ) • 01/0 01141
-1N
LL'VAL VE E 1•10
0347G 3/88
AIR VALVE
REF.
PART NUMBER NO.
NO. DESCRIPTION
REQ.
1 1018-0032 BOLT, U (3/8 x 3-3/4) 2

2 9W01-0005 PLATEWASHER (3/8) 4
3 9W03-0006 LOCKWASHER (3/8) 4
4 9N01-0009 NUT (3/8) 4
5 3288-0026 VALVE, BALL (2" HIGH PRESSURE) 1
6 9P08-0156 NIPPLE, X-HVY CLOSE (2MP) 3
7 3343-0009 TEE, HIGH PRESSURE (2FP x 2FP x 2FP) 2
8 9P09-0026 PLUG, SQ HD (2MP) 1
9 2220-0008 CONNECTOR (2MP x 2FPS) 2
10 9P01-0033 BUSHING, REDUCING (2MP x 1/2FP) 1
11 3336-0003 TEE, SERVICE DS (1/2MP x 1/2FP x 1/2FP) 2
12 3337-0015 NIPPLE, X-HVY DS (1/2MP x 2) 1
13 1162-0027 VALVE, RUNNING BLOWDOWN (1/2P) 1
14 0237-0025 NIPPLE, RBDV OUTLET (.2610) 1
15 3340-0002 ELBOW, 90° DS (1/2FP x 1/2FP) 1
16 3332-0061 CONNECTOR (1/2MP x 3/4M37) 1
17 0092-0006 COCK, DRAIN (1/2P) 2
18 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 1
19 3332-0059 CONNECTOR (1/2MP x 1/4M37) 1
20 9P01-0035 BUSHING, REDUCING (2MP x 1FP) 1
21 3337-0033 NIPPLE, X-HVY DS (1MP) 1
22 3343-0007 TEE, DS (1FP x 1FP x 1FP) 1
24 3336-0003 TEE, SERVICE DS (1 /2MP x 1/2FP x 1/2FP) 2
25 3337-0011 NIPPLE, CLOSE X-HVY DS (1/2MP) 2
26 2250-0006 VALVE, CHECK (1/2P) 2
27 3332-0059 CONNECTOR (1/2MP x 1/4M37) 1
28 3852-0003 TEE (1/2MP x 1/2M37 x 1/2M37) 1
29 3897-0001 TUBE, REDUCER ST (1/2 x 1/4) 1
30 3890-0005 NUT, TUBE (37 FLARE) 1
31 3896-0001 TEE (1/4F37 x 1/4M37 x 1/4M37) 1
32 9P08-0077 NIPPLE, CLOSE X-HVY (1MP) 1
33 3332-0023 CONNECTOR (1MP x 1M37) 1
34 3288-0010 VALVE, BALL (1) 1
35 0882-0031 LEVER, BALL VALVE 1
36 9S01-0008 CAPSCREW (1/4 x 1-1/4) 1
37 0374-0003 LOCKNUT (1/4) 1
38 0678-0011 YOKE (5/16NF x 7/16 SLOT x 3/8 PIN) 1
39 9N07-0003 NUT, JAM (5/16 NF) 1
40 0669-0005 PIN, YOKE (3/8) 1
41 9C01-0005 PIN, COTTER (3/32 x 3/4) 1
42 0877-0657 SUPPORT, CABLE 2
43 0923-0045 CABLE, CONTROL (31 IN.) 1
44 3562-0047 BLOCK, MOUNTING 1
45 0923-0024 CONTROL LEVER ASY 1
46 9S01-0017 CAPSCREW (5/16 x 1/2) 1
47 9W05-0003 LOCKWASHER, ET (5/16) 1
48 0678-0009 YOKE ASY (WITH PIN AND COTTER PIN) 1
49 0923-0038 CONTROL CABLE (54 IN.) (TEE HANDLE) 1

•
3-3
3/88
0347G
AIR VALVE
NO.
REF. DESCRIPTION REQ
PART NUMBER
NO.
1
50 9N07-0002 NUT, JAM (1/4 NF)
2
51 3045-0001 PROTECTOR, AIR HOSE
2
52 0045-0008 CHAIN, SAFETY W/CLAMP (2-1/2)
1
53 1184-0016 HOSE ASY, AIR 2 x 43
1
54 1184-0074 HOSE ASY, AIR 2 x 84
1
55 1184-0157 HOSE ASY, AIR 3/4 x 110 37S
1
56 1313-0097 HOSE, COMPR 1 /4 x 13 S90
1
57 1313-0106 HOSE, COMPR 1/4 x 46 590 1
58 2826-0895 HOSE, HYD 1/4 x 22 100R1 37S 1
59 2826-0800 HOSE, HYD 1/4 x 25 100R1 S90 1
60 2826-0644 HOSE, HYD 1/4 x 18 100R1 37S
1
61 2826-0914 HOSE, HYD 1/2 x 115 100R2 375
1
62 2826-0628 HOSE, HYD 1 x 160 100R2 37S
1
63 3332-0095 CONNECTOR (1MP x 3/4M37)
1
64 9P01-0023 BUSHING, REDUCING (1-1 /4MP x 1FP)
1
65 0862-0255 BRACKET, MUFFLER (WELDED TO ENGINE FRAME)
1
66 0129-0001 MUFFLER

Printed in U.S.A.
3-4
0
•
AIR-OIL TANK GROUP
27
dir 4r 28
26 t "J111 hill I 1 IV
29 .J. TO AIR
32 105 VALVE
33
gh. 97
13 12 10 TO SAVENGER
r, illiszt, is1 FILTER
11
111 •
rezar
'""Illgg*.* aiii
c
It • ._ gw)
it to c "'•
all
7 '
TO COMP.
107 CONTROL FILTER
56
TO OIL
STOP VALVE
-130 COMPRESSOR
77 — AIR OVT
108
20
62 63
60
50
101
TO COMPRESSOR
AIR-INTAKE
g\ DRAIN
95 TO CONTROL
MANIFOLD
PANEL
94 96
102
i" - C
91 ;
92 86
TO COMPRESSOR
88 THROTTLE VALVE
SUPPORT
°
87 96
3-5
0354G 3/88
AIR-OIL TANK GROUP
REF. NO.
NO. PART NUMBER DESCRIPTION
REQ.
1 0278-0064 TANK, AIR-OIL 1

2 0480-0124 TANK, LID 1
3 3998-0012 ELEMENT, OIL SEPARATOR 1
4 0978-0212 CAPSCREW (3/4 x 2-3/4 - ASME SA-193 GRADE B7) 12
(TORQUE 280 x 300 LB-FT)
5 0570-0032 WASHER, HT (1-5/16 x 1/8 x 25/32) 12
6 9P08-0133 NIPPLE, CLOSE X-HVY (1-1/2MP) 1
7 3343-0014 TEE, HIGH PRESSURE (1-1/2FP x 1-1/2FP x 1-1/2FP) 1
8 2247-0053 VALVE, SAFETY 400 (1-1/2) (Kunkle Figure # 23-MA) 1
9 3337-0038 NIPPLE, REDUCING DS (1-1/2MP x 1-1/4MP) 1
10 2253-0009 REGULATOR (1-1/4) (Fisher 620 SERIES) 1

5000-5784 DIAPHRAGM (Fisher # 10A0507x022) (THICK VITON)
11 9P01-0021 BUSHING, REDUCING (1-1/4MP x 3/4FP) 1

12 9P07-0032 TEE, SERVICE (3/4MP x 3/4FP x 3/4FP) 1
13 9P09-0009 PLUG, PIPE SQ HD (3/4MP) 1
14 9P08-0055 NIPPLE, CLOSE X-HVY (3/4MP) 1
15 9PO4-0004 CROSS (3/4FP) 1
17 2064-0018 GAUGE, PRESSURE (0-160 PSI) 1
18 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 2
20 3332-0053 CONNECTOR (3/8MP x 3/8M37) 2
22 3341-0004 ELBOW, 90° SERVICE DS (1/2MP x 1/2FP) 1
23 1162-0024 VALVE BLOWDOWN (1/2FP) 1

5000-9714 KIT, SEAL (Lexair # 20-0922)
24 3594-0009 MUFFLER, HI-PRESSURE (1/2MP) 1

25 3877-0011 ELBOW, 90° (1/8MP x 1/4M37) 1
26 9P08-0162 NIPPLE, X-HVY (2MP x 4) 1
27 3340-0005 ELBOW, 90° HI-PRESSURE (2FP x 2FP) 1
28 3997-0011 VALVE, MINIMUM PRESSURE 1
29 2221-0062 ELBOW, 90° (1-1/2MP x 1-1/2FPS) 1
30 0710-0007 CONNECTOR, ALTERATION 1
31 3169-0117 TUBE, OIL SCAVENGER 1
32 2164-0018 ELBOW, 90° (1/4MP x 1/4T) 1
33 3332-0065 CONNECTOR (1/4FP x 1/4M37) 1
34 3340-0013 ELBOW, 90° X-HVY (1-1/2FP x 1-1/2FP) 2
35 3331-0124 PIPE, SCH 80 (1-1/2MP x 14) 1
36 3331-0090 PIPE, SCH 80 (1-1/2MP x 26-1/2) 1
37 2221-0067 ELBOW, 90° (1-1/2FP x 1-1/2FPS) 1
38 0991-0096 ADAPTER, OIL LEVEL GAUGE (2MP) 1
39 0598-0035 GAUGE, OIL LEVEL 1
40 2558-0009 BUSHING, REDUCING DS (1MP x 1/2FP) 1

Printed in U.S.A.
3-6
3/88
0354G AIR-OIL TANK GROUP
NO.
REF. DESCRIPTION RED.
NO. PARTNUMBER
1
43 3288-0014 VALVE, BALL (1/2FP) 1
44 9P08-0050 NIPPLE (1/2MP x 9) 1
45 9P03-0004 COUPLING (1/2FP) 1
46 9P09-0006 PLUG, PIPE SQ HD (1/2MP) 1
47 0234-0047 FITTING ASY 1
48 2764-0089 0-RING (.139 x 3.859) 2
DE 5)
49 0978-0074 CAPSCREW (1 /2 x 1-3/4 - SAE GRA 12
50 9W03-0008 LOCKWASHER (1/2) 2
GRADE 8)
51 0978-0116 CAPSCREW (1 /2 x 2-1/4 - SAE 1
BRACKET, MOTION RESTRAINT ROD T
52 0862-0190 1
CONNECTOR (2-1/2MP x 3M3 7)
53 3332-0068 1
54 3346-0014 PLUG, 0-RING (1-5/8 THD) 1
55 2764-0119 0-RING (.118 x 1.475) 1
56 0877-0873 SUPPORT, MOTION RESTRAINT ROD 1
57 0472-0024 ROD, MOTION RESTRAINT 4
58 9N06-G007 NUT, JAM (1) 8
DE 5)
59 0978-0085 CAPSCREW (1 /2 x 1-1/2 - SAE GRA 8
61 9N01-0011 NUT (1/2) 1
62 0862-0031 SUPPORT, HANSEN SOCKET 1
63 2050-0004 COUPLING, QUICK DSC SKT (3/8MP) 1
64 0234-0081 FITTING, AIR-OIL DISCHARGE 1
65 2764-0089 0-RING (.139 x 3.859 VITON) 8
66 0252-0003 CAPSCREW, HT (M16 x 2 x 45mm) 8
67 9W03-0010 LOCKWASHER (5/8) 1
68 2145-0013 SWITCH, TEMP - CLOSE (255F) 1
69 2159-0004 SENDING UNIT, TEMP (100-280) 1
FP)
70 2258-0003 BUSHING, REDUCING DS (1/2MP x 1/4 2
TEE, SERVICE DS (1/4MP x 1/4FP x 1 /4FP)
71 3336-0001 1
72 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 1
73 3332-0026 CONNECTOR (1/4MP x 1/4M37) 1
74 3877-0003 ELBOW, 90° (3/4MP x 3/4M37) 1
75 2210-0065 VALVE, CHECK (2-1 /2) 2
76 0312-0021 GASKET, COMPANION FLANGE (2-1/2) 1
77 0822-0168 SPACER 2
78 0995-0081 FLANGE, SPLIT k 2
79 0213,0025 RETAINER, SPLIT FLANGE er 1
80 2764-0026 0-RING (.139 x 2.734) gyp'° 1
81 3346-0023 PLUG, PIPE FLUSH DS (2MP) 1
ELBOW, 90° (1/4MP x 1/4M37) .,
T82
4
___
3877-0001
1184-0125
9502-0087
HOSE, DISCHARGE (2-1/2
CAPSCREW (3/4NF x 6)
x 32- 1/2 SPL )-. 24apt ose 1
8
8
85 0374-0020 LOCKNUT (3/4NF) 1
86 1460-0001 TANK, OIL COLLECTION (5 GAL) 4
87 0978-0161 CAPSCREW (1 /2 x 1 - SAE GRADE 5) 4
88 9W03-0008 LOCKWASHER (1/2) 1
3/4FP)
89 3336-0004 TEE, SERVICE DS (3/4MP x 3/4FP x 1
6).
90 2247-0068 VALVE, SAFETY (3/4MP) (Eaton # 9540 1
UCI NG DS (3/ 4MP x 1/4 FP)
91 2558-0005 BUSHING, RED

anted In U.S.A.
3-7
0354G 3/88
AIR-OIL TANK GROUP
REF. NO.
NO. PART NUMBER DESCRIPTION RECL
92 3332-0026 CONNECTOR (1/4MP x 1/4M37) 2

94 1162-0026 VALVE, NORMALLY OPEN (3/4FP) (Lexair # 32132) 1

5000-9715 KIT, SEAL (Lexair # 20-1018)
95 3332-0024 CONNECTOR (3/4MP x 3/4M37) 1
96 3877-0002 ELBOW, 90° (1/2MP x 1/2M37) 1
97 1313-0133 HOSE, COMPR 1/4 x 126 37S 1
98 2826-0398 HOSE, HYD 1/4'x 120 100R1 37S 1
99 1313-0035 HOSE, COMPR 1/4 x 92 37S 2
100 1313-0108 HOSE, COMPR 1/2 x 76 S45 1
101 1313-0016 HOSE, COMPR 3/4 x 31 S90 1
102 1313-0132 HOSE, COMPR 1/4 x 86 S90 1
103 1313-0135 HOSE, COMPR 1/4 x 30 37S 1
104 1313-0004 HOSE, COMPR 1/4 x 35 37S 1
105 1184-0016 HOSE ASY, AIR 2 x 43 1
106 1313-0136 HOSE, COMPR 1-1/2 x 136 NPT 1
107 1313-0133 HOSE, COMPR 1/4 x 126 37S 1
108 2826-0908 HOSE, HYD 3/8 x 96 100R2 37S 1

Printed in U.S.A.
3-8
COMPRESSOR CLUTCH GROUP
47
IT
36
SO
0
CO
0333G 3/88
REF. NO.
REO.
1 0602-0009 KEY, CLUTCH SHAFT COUPLING 1

2 0620-0009 RING, CLUTCH SHAFT DRIVE 1
3 2212-0002 FITTING, GREASE (60° x 1/8P - 60 PSI) 1
4 0570-0073 PLATEWASHER (H/T 3.00 x .44 x .81) 1
(TORQUE 300 LBS-FT.)
6 0621-0028 HOUSING, CLUTCH 1
8 9W03-0007 LOCKWASHER (7/16) 12
9 9N01-0010 NUT (7/16) 12
10 0213-0015 RETAINER, OIL SEAL 1
11 2764-0033 0-RING (.103 x 6.487) 1
12 0886-0076 SEAL, OIL (5 x 6 x 1/2) (Chicago Rawhide # 49928) 1
(TYPE CRWH1-LIP CODE R)
13 2649-0003 RING, RETAINING (Spirolox # RR-725) 1
14 9S01-0039 CAPSCREW (3/8 x 1-1/2) 2
15 9W03-0006 LOCKWASHER (3/8) 2
16 0270-0025 LOCKWASHER (Twin Disc # A1589) 1
17 0974-0025 NUT, SHAFT (Twin Disc # 1086) 1
18 0623-0007 SHAFT, CLUTCH 1
19 0625-0007 YOKE, OPERATING 1
20 2003-0005 KEY, WOODRUFF #15 2
22 0994-0002 FITTING (1/8P x 1/4T) 1
23 0654-0002 HOSE, GREASE (3/16 x 16-3/8) 1
24 0994-0001 FITTING, ELBOW (5/8NF x 1/4T) (Twin Disc # 1283) 1
25 9W03-0010 LOCKWASHER (5/8) 1
26 9N07-0007 NUT, JAM (5/8 NF) 1
27 2208-0001 FITTING, GREASE (1/8P) 1
28 0550-0004 4 KEY (1/4 x 1-1/16) 1
29 0630-0026 LEVER, CLUTCH 1
30 9501-0036 CAPSCREW (3/8 x 3/4) 1
31 0508-0008 WASHER, THRUST (1-1/2 x 3/16 x 7/16) 1
32 9W03-0006 •
LOCKWASHER (3/8) 1
33 1058-0001 SHAFT, CLUTCH 1
34 0602-0008 KEY, DRIVE CLUTCH 1
35 0620-0008 RING, DRIVE 1
37 9W03-0008 LOCKWASHER (1/2) 8
38 0978-0188 CAPSCREW (7/16 x 1-3/4 SAE GRADE 5) 12
39 9W03-0007 LOCKWASHER (7/16) 12
40 9P07-0001 TEE (1/8FP X 1/8FP x 1/8FP) 1
41 9P08-0001 NIPPLE, CLOSE (1/8MP) 1
42 0654-0002 HOSE, GREASE (3/16 x 16-3/8) 2
44 9N07-0007 NUT, JAM (5/8 NF) 1
45 2208-0001 FITTING, GREASE (1/8MP) 1
46 0994-0001 FITTING (5/8NF x 1/4T) 1
47 0480-0119 PLATE, CLUTCH HOUSING COVER 1
48 0180-0056 LATCH, ADJUSTABLE COMPRESSOR COVER 2

Printed in U.S.A.
3-10
3/88
0333G
NO.
REF. DESCRIPTION
PART NUMBER REQ
NO.
LOCKWASHER (5/8) 1
49 9W03-0010
BEARING, FLYWHEEL (ON ENGINE) 1
50 5000-6930
(85mm OD x 35mm BORE x .8268 LONG)
(GM # 2947905)
or
(N.D # 299607)
CLUTCH ASY (Twin Disc Model SP214 Clutch; 1
51 0600-0014
Spec # 35092)
NIPPLE (1/8P x 2) 1
52 9P08-0005
9P03-0001 COUPLING (1/8FP) 1
53
0994-0002 FITTING (1/8MP x 1/4T) 3
54

Printed In U.S.A.
3-11
CLUTCH CONTROL
Ra
3-12
0324G 3/88
CLUTCH CONTROL
REF. NO.
REO.
1 3292-0021 PAD, PIVOT SHAFT HOUSING 1

2 3232-0027 HOUSING, SHAFT PIVOT 1
4 9W03-0008 LOCKWASHER (1/2) 4
5 0860-0101 BUSHING (1-1/8 x 1 x 1 DU) 2
6 2208-0001 FITTING, GREASE (1/8MP) 1
7 0509-0050 SHAFT, PIVOT CLUTCH HANDLE 1
8 0630-0028 LEVER, CLUTCH SHAFT 1
9 0550-0004 KEY, DRIVE (1/4 x 1/4 x 1-1/16) 1
10 9S01-0042 CAPSCREW (3/8 x 2-1/4) 1
11 0374-0033 LOCKNUT (3/8) 2
12 9S01-0040 CAPSCREW (3/8 x 1-3/4) 1
13 2094-0008 ROD, CLUTCH OPERATING 1
14 0678-0005 YOKE 2
15 0669-0006 PIN, YOKE (5/8) 2
16 9C01-0010 PIN, COTTER (1/8 x 1) 2
17 0630-0028 LEVER, CLUTCH 1
18 0862-0168 BRACKET, CLUTCH LEVER SPRING 1
19 0609-0001 SPRING, CLUTCH RELEASE 1
20 9S03-0008 CAPSCREW (SOCKET) (5/16 x 2) 1
21 9N01-0008 NUT (5/16) 2
22 9W01-0004 PLATEWASHER (5/16) 2
23 9W03-0005 LOCKWASHER (5/16) 2

Printed In
3-13
COMPRESSOR AIR CLEANER
TO COMPRESSOR
AIR INTAKE
taint
ft
fr.
15
irli el
) th
14 I3 Ilk
..
,1„ ,I
CP „) 14
,111°
16C
3-14
0298G 3/88
COMPRESSOR AIR CLEANER
REF. NO.
NO.
PART NUMBER DESCRIPTION
REQ
r
0378-0040 CLEANER, AIR (Donaldson # STG14-0076) 1

5000-4284 ELEMENT, PRIMARY SMP (Donaldson # P18-1041) 1
Cr) 'Cr L11 l01~CO al CD •-•NM ef 111 t%. CO 01
5000-4285 ELEMENT, SAFETY (Donaldson # P11-9370) 1

0378-0031 BAND, CLEANER MOUNTING (Donaldson # AAHOO-350) 1
9S01-0061 CAPSCREW (7/16 x 1-1/4) 4
9W01-0006 PLATEWASHER (7/16) 4
9W03-0007 LOCKWASHER (7/16) 4
9N01-0010 NUT (7/16) 4
0877-0823 SUPPORT, AIR CLEANER 1
9S01-0071 CAPSCREW (1/2 x 1-1/4) 4
9W02-0006 PLATEWASHER (1/2 SAE) 4
9W03-0008 LOCKWASHER (1/2) 4
2020-0034 COUPLING, HOSE ST (6) 2
0556-0013 CLAMP, HOSE (5.625 TO 6.500) 8
0823-0046 TUBE, CONNECTOR (6 IN. DIA.) 1
2077-0003 GAUGE ASY, VACUUM 1
9P05-0002 ELBOW, 90° (1/8FP x 1/8FP) 1
2018-0013 NIPPLE, HOSE (1/4H x 1/8MP) 2
9H01-0001 HOSE, AIR (1/4) 5'

Printed in U.S.A.
3-15
SCAVENGER LINE AND CONTROL LINE FILTER
12
FROM
AIR- OIL
TANK
TO COMP,
CONTROLS
FROM
AIR- OIL
TANK
3-16
0318G 3/88
SCAVENGER LINE AND CONTROL LINE FILTER
REF. NO.
PART NUMBER DESCRIPTION R EQ.
NO.
1 0862-0172 BRACKET, MOUNTING 1

2 9S01-0004 CAPSCREW (1/4 x 1 /2) 2
3 9W03-0004 LOCKWASHER (1/4) 6
4 9S01-0006 CAPSCREW (1/4 x 3/4) 4
5 9N01-0007 NUT (1/4) 2
6 3151-0012 FILTER, COALESCING (500 PSI) 2

Consisting of:
6A 5000-8759 SEAL, FILTER 1
6B 5000-7205 ELEMENT, FILTER 1
7 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 3

8 9S01-0014 CAPSCREW (1/4 x 3) 2
9 0277-0002 FILTER ASY 1

Consisting of:
9A 5000-3532 GASKET, FILTER 1
9B 2295-0015 ELEMENT, FILTER 1
10 3332-0039 CONNECTOR (1/4MP x 1/4M37 .055 RES.) 1

11 3892-0001 ELBOW, 90° (1/4F37 x 1/4M37) 1
12 1313-0133 HOSE, COMPR 1/4 x 126 37S 2
13 1313-0081 HOSE, COMPR 1/4 x 48 37S 1
14 2826-0641 HOSE, HYD 1/4 x 74 100R1 590 1

Printed in U.S.A.
3-17
COMPRESSOR AIR DELIVERY CONTROL
BRACKET WELDED
TO FRAME
FROM CONTROL
LINE FILTER
24
22
23
13
21
Sare
10 e
20
23 "Cfie,
13
21
COMP. LOAD SELECT()

25 IN CONTROL PANEL fler
ELBOW WELDED
TO FRAME
25
14
16
15
BRACKET WELDED
TO FRAME IB
19
17 13
4
TO COMP, SERVO
CYLINDER
25
TO RUNNING
SLOWDOWN VALVE
3-18
0353G 3/88
COMPRESSOR AIR DELIVERY CONTROL
REF. NO.
S
1 0598-0016 BRACKET, PILOT VALVE 1

2 2767-0001 VALVE, PRESSURE RELIEF (Fisher Type 98HH)
3 9503-0006 CAPSCREW, SKT (1/4 x 1) 3
4 3336-0001 TEE, SERVICE DS (1/4MP x 1/4FP x 1 /4FP) 2
5 2170-0015 CONNECTOR, MALE (1/8P x 1/4T NYLON) 1
6 2247-0065 VALVE, SAFETY (1/4) 1
7 9P08-0010 NIPPLE, CLOSE X-HVY (1/4MP) 1
8 9PO4-0002 CROSS (1/4) 1
9 2164-0018 ELBOW, MALE (1/4P x 1/4T NYLON) 1
10 0237-0018 NIPPLE, RESTRICTED (.078) 1
11 3332-0065 CONNECTOR (1/4FP x 1/4M37) 1
12 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 2
13 3332-0026 CONNECTOR (1/4MP x 1/4M37) 6
15 2253-0015 REGULATOR, PROPORTIONAL 1
(A. W. Cash Type CP # 12625 1/4)
16 3852-0001 TEE (1/4MP x 1/4M37 x 1/4M37) 1
17 0877-0837 SUPPORT, REGULATOR 1
18 9521-0023 SCREW, MCH PH RD (12/24 x 1) 3
19 2253-0022 REGULATOR (1/4FP) 1
(Norgren # 11-002-013 RELIEVING TYPE)
20 3288-0020 VALVE, BALL 1
22 9Y02-0017 TUBING, NYLON (1 /4 OD x .050 WALL) 6"
23 1313-0003 HOSE, COMPR 1/4 x 30 S45 2
24 1313-0081 HOSE, COMPR 1/4 x 48 375 1
25 1313-0097 HOSE, COMPR 1/4 x 13 S90 3
26 1313-0132 HOSE, COMPR 1/4 x 86 S90 1

SCHRAMM, 1NC,, West Chester, PA
Printed In U.S.A.
3-19
COMPRESSOR AND AIR SELECTOR VALVES
COMPRESSOR LOAD SELECTOR VALVE
PS9. 0-
‘S5'3
4)'‘
VC‘
ekt
5Vg"
OPP
ekt
AIR GAGE PRESSURE SELECTOR VALVE
12
Ii
I0
3-20
0296G 3/88
COMPRESSOR AND AIR SELECTOR VALVES
REF. NO.
1 3288-0020 VALVE, BALL 1

3 3332-0026 CONNECTOR (1/4MP x 1/4M37) 4
4 3288-0021 VALVE, BALL (3-WAY) 1
5 1313-0003 HOSE, COMPR 1/4 x 30 S45 2
6 1313-0035 HOSE, COMPR 1/4 x 92 37S 1
7 1313-0106 HOSE, COMPR 1/4 x 46 S90 1
8 2826-0003 HOSE, HYD 1/4 x 10 100R1 NPT 1
9 2221-0030 ELBOW 45° (1/4MP x 1/4FPS) 1
10 2064-0003 GAUGE, AIR (0-400 PSI) 1
11 2558-0001 BUSHING, REDUCING, DS (1/4MP x 1/8FP) 1
12 2221-0046 ELBOW 90° (1/4FP x 1/4FPS) 1

Printed in U.S.A.
3-21
IT TO OIL
STOP VALVE
36
FROM
AIR-OIL
TANK
COMPRESSOR OIL FILTERS
0351G 3/88
REF. NO.
REQ.
1 0670-0070 RADIATOR AND COMPR OIL COOLER ASY 1

2 0877-0817 SUPPORT, OIL FILTER 1
3 9501-0071 CAPSCREW (1 /2 x 1-1/4) 8
4 9W03-0008 LOCKWASHER (1/2) 8
5 9501-0046 CAPSCREW (3/8 x 3-1/4) 4
6 9W03-0006 LOCKWASHER (3/8) 4
7 0978-0018 CAPSCREW (5/16 x 3/4 - SAE GRADE 5) 4
8 9W03-0005 LOCKWASHER (5/16) 8
9 0556-0010 CLAMP (3.560 - 4.500) 1
10 0277-0048 FILTER ASY, OIL (10 MICRON - 3/ELEMENT) 1

Consisting of:
10A 0978-0018 CAPSCREW (5/16 x 3/4 - SAE GRADE 5) 4
108 9W03-0005 LOCKWASHER (5/16) 4
10C 5000-6761 0-RING, BOWL 1
10D 5000-7564 GROMMET, RUBBER 6
10E 5000-5520 CONNECTOR ELEMENT 2
1OF 2295-0020 ELEMENT, FILTER (10 MICRON) 3
11 2221-0077 CONNECTOR (ALTERED) (1-1/2MP x 1-1/2FPS) 4

12 0862-0264 BRACKET, INDICATOR MTG 2
13 2932-0017 INDICATOR, DIFF PRES (25 PSIG) 2
14 9S01-0017 CAPSCREW (5/16 x 1/2) 4
15 9S01-0004 CAPSCREW (1/4 x 1/2) 4
16 9W03-0004 LOCKWASHER (1/4) 4
17 2164-0035 ELBOW, 90° (1/8P x 1/4T) 8
18 9M05-0330 TUBING, COPPER (1 /4 OD x .049 WALL) 4'
19 2220-0007 CONNECTOR (1-1/2MP x 1-1 /2FPS) 1
20 2157-0010 VALVE ASY, THERMAL CONTROL 1

Consisting of:
20A 3232-0009 HOUSING, THERMOSTAT 1
208 2764-0025 0-RING 1
20C 2157-0011 THERMOSTAT, 180° 1
20D 2764-0084 0-RING 1
20E 0480-0105 COVER, HOUSING 1
20F 9W03-0006 LOCKWASHER (3/8) 4
20G 0978-0013 CAPSCREW (3/8 x 1 - SAE GRADE 5) 4
21 9W03-0006 LOCKWASHER (3/8) 4

22 9501-0036 CAPSCREW (3/8 x 3/4) 4
23 3341-0018 ELBOW, 90° SERVICE 300# (1-1/2MP x 1-1/2FP) 3
24 2221-0062 ELBOW, 90° (1-1/2MP x 1-1/2FPS) 5
25 0877-0866 SUPPORT, OIL FILTER 1
i
I e, WAYS GIVE EQUIPMENT SERIAI

03516 3/88
NO.
REF.
NO.
26 0277-0049 FILTER ASY, OIL (60 MICRON - SS/2 ELEMENT REUSABLE) 1

Consisting of:
26A 0978-0018 CAPSCREW (5/16 x 3/4 - SAE GRADE 5) 4
26B 9W03-0005 LOCKWASHER (5/16) 4
26C 5000-6761 0-RING (BOWL) 1
26D 5000-7564 GROMMET, RUBBER 4
26E 5000-5520 CONNECTOR, ELEMENT 1
26F 2295-0021 ELEMENT, FILTER (REUSABLE) 2
27 2764-0004 0-RING (.139 x 1.859) 2

28 0995-0014 FLANGE, HYD (1-1/2FP x 1-1 /2PAD) 2
29 9503-0016 CAPSCREW, SOCKET (1/2 x 1-3/4) 8
30 3343-0014 TEE, HIGH PRESSURE (1-1/2FP x 1-1/2FP x 1-1/2FP) 1
31 2221-0070 ELBOW, 45° (1-1/2MP x 1-1/2FPS) 1
32 2221-0067 ELBOW, 90° (1-1/2FP x 1-1 /2FPS) 1
33 1313-0136 HOSE, COMPR 1-1/2 x 140 NPT 1
34 1313-0033 HOSE, COMPR 1-1/2 x 40 NPT 1
35 1313-0017 HOSE, COMPR 1-1/2 x 33 NPT 2
36 1313-0022 HOSE, COMPR 1-1/2 x 180 NPT 1
37 1313-0020 HOSE, COMPR 1-1/2 x 76 NPT 2

ALWAYS GIVE EQUIPMENT &
Printed In U.S.A. NUMBER WHEN ORDERING PA
3-24
•
COMPRESSOR CONNECTIONS
AIR IN
t....t:::-‘.....,k,
•y 1 • iHI
f
—..?"-
0. ..•••••<,:- .1r9...e„0 .. \
ie
t I e eg-al 1" 1
l
1
1 41
10
41
38
cc(
FROM
SCAVENGER II 12 -
e
zi
ft glees,
rd.
,fr°2
FILTER 12 II
44 44 20 41
d1' ;Ai
39
21
% 11.11111111111.1\001.,
0 12 TO 16
34 „04 INTERSTAGE
II
PRESSURE GAUGE
42
42 13
ft 17
14
16
TO COMP.
DISCHARGE
37 FROM
25
Ise FILTER
43
40
42 25 24 33
ste, 31
it;*a 2
42 cr. 30
"e0
0 F.• 34
34 26
32 o
29 27- 28
• 36 22
3-25
0337G 3/88
COMPRESSOR CONNECTIONS
REF. NO.
PART NUM BER
s NO. DESCRIPTION
RECL
1 3999-0032 COMPRESSOR 900/350 1

2 3337-0012 NIPPLE, REDUCING DS (1/2MP x 1/4MP) 1
3 3832-0001 ELBOW, 90° (1/4F37 x 1/4M37) 1
4 3892-0003 ELBOW, 90° (1/2F37 x 1/2M37) 1
5 3332-0029 CONNECTOR (1/2MP x 1/2M37) 1
6 3877-0002 ELBOW, 90° (1/2MP x 1/2M37) 1
7 0237-0012 RESTRICTOR, INJECTION LINE 1
8 0134-0017 METRIC SEALING WASHER (48mm) 1
9 3332-0071 CONNECTOR (M16 x 1/2M37) 1
10 0134-0014 METRIC SEALING WASHER (16 x 32) 1
11 3332-0070 CONNECTOR (M26 x 1/2M37) 3
12 0134-0006 METRIC SEALING WASHER (27 x 32) 3
13 2253-0011 VALVE, PRESSURE REDUCING 1
15 0862-0084 BRACKET, REGULATOR 1
16 3877-0002 ELBOW, 90° (1/2MP x 1/2M37) 2
19 2558-0003 BUSHING, REDUCING DS (1/2MP x 1/4FP) 1
21 2064-0018 GAUGE, PRESSURE 1
22 0877-0254 BRACKET, OIL STOP 1
23 3996-0011 VALVE, OIL STOP ALTERED 1
24 1018-0009 BOLT, U (3/8 x 4-3/8) 2
25 9H01-0048 HOSE, AIR (3/8 x 4) 2
26 0374-0033 LOCKNUT (3/8) 4
27 0995-0047 FLANGE, HYD (2FP x 2 FLANGE) 2
28 2764-0079 0-RING (.139 x 2.234) 2
29 9503-0023 CAPSCREW, SOCKET HEAD (1/2 x 2) 8
30 2558-0029 BUSHING, REDUCING DS (2MP x 1-1/2FP) 1
31 2221-0062 ELBOW (1-1/2MP x 1-1/2FPS) 1
32 0566-0057 MANIFOLD, OIL STOP VALVE 1
33 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 1
34 3877-0003 ELBOW, 90° (3/4MP x 3/4M37) 3
35 3877-0002 ELBOW, 90° (1/2MP x 1/2M37) 2
36 3346-0001 PLUG, DS (1/4P) 1
37 1313-0004 HOSE, COMPR 1/4 x 35 37S 1
38 2826-0641 HOSE, HYD 1/4 x 74 100R1 S90 1
39 1313-0082 HOSE, COMPR 1/4 x 74 37S 1
40 1313-0053 HOSE, COMPR 1/2 x 20 37S 1
41 1313-0109 HOSE, COMPR 1/2 x 28 S90 2
42 1313-0134 HOSE, COMPR 3/4 x 19 S90 2
43 1313-0022 HOSE, COMPR 1-1/2 x 18 NPT 1
44 1313-0054 HOSE, COMPR 3/4 x 27 S90 1

3-26
COMPRESSOR AIR INTAKE
16
18
14
12 22
TO OIL
COL LECTION
TANK
10
FROM
COMPRESSOR •
CONTROLS
22
13
14
15
TO OIL
COLLECTION
TANK
2 21
/, 75-k.
A.,rci:
•:co
141 AV?
-
{ cse de/
I\ I II
3-27
._
3/88
0301G
COMPRESSOR AIR INTAKE
NO.
REF. DESCRIPTION RE Q
NO. PART NUMBER
SUPPORT, COMPR THROTTLE VALVE 1

1 0877-0434
GASKET, FLANGE - VALVE SUPPORT 1
2 0312-0015
CAPSCREW, HT (M16 x 2 x 35mm) 8
3 0252-0002
LOCKWASHER (5/8) 8
4 9W03-0010
ELBOW, 90° (1/8MP x 1/4M37) 1
5 3877-0011
VALVE, THROTTLE (150mm ALTERED) 1
6 3995-0010
CYLINDER, SERVO (Hoerbiger # 21-557262) 1
7 5000-7908
KIT, REPAIR SERVO CYLINDER (For Ref. # 7) 1
8 5000-5137
ROD, END (W/GREASE FITTING) 1
9 2095-0008
GASKET, FLANGE - THROTTLE VALVE 2
10 0312-0014
FLANGE, THROTTLE VALVE CLAMP 1
11 0995-0051
CAPSCREW (3/8 x 2-3/4) 8
12 9S01-0044
13 16
14 9W03-0006 LOCKWASHER (3/8)
NUT (3/8) 8
15 9N01-0009
MANIFOLD, AIR CLEANER 1
16 0436-0052
GASKET, FLANGE - AIR CLEANER 1
17 0312-0013 8
18 9S01-0038 CAPSCREW (3/8 x 1-1/4)
ELBOW, 90° (1/8MP x 1/4M37) 1
19 3877-0011
CONNECTOR (1/4MP x 1/2M37) 1
20 3332-0090 1
21 1313-0108 HOSE, COMPR 1/2 x 76 S45
HOSE, COMPR 1/4 x 86 S90 2
22 1313-0132

SCHRAMM, INC., West Chest NUMBER WHEN ORDERING PARTS.
Printed In U.S.A.
3-28
0
CONTROL PANEL - ENGINE
16,17,18
/
I
4-1
3/88
0338G
CONTROL PANEL - ENGINE
NO.
REF. DESCRIPTION REO
PART NUMBER
NO.
PANEL, ENGINE CONTROL 1

1 0998-0260
TACHOMETER, HOURMETER ADJ (24V) 1
2 2072-0024
AMMETER (60 AMP) 1
3 2067-0006
GAUGE, ENGINE OIL PRESSURE (0-100) 1

4 2065-0030
Consisting of:
RESISTOR (BACK OF GAUGE) 1
4A 2131-0011 *
GAUGE, ENGINE WATER TEMP 1

5 2066-0006
Consisting of:
5A 2131-0011 *
GAUGE, COMPRESSOR OIL TEMP (100°-280°) 1

6 2065-0025
Consisting of:
6A 2131-0011 *
GAUGE, AIR (0-400 PSI) 1

7 2064-0003
GAUGE, INTERSTAGE PRESSURE (0-200 PSI) 1
8 2064-0004
SWITCH, TOGGLE SPST (LIGHTS) 2
9 0049-0006
2
10 3139-0003 BOOT, TOGGLE SWITCH
4
11 0192-0004 SWITCH, PUSH BUTTON
1
12 0192-0002 SWITCH, IGNITION STARTER
1
13 2104-0001 LAMP, INDICATOR GREEN (SAFETY CIRCUIT)
Consisting of:
BULB (T-3-1/4 28V) 1
13A 2103-0006 *
1
14 3288-0021 VALVE, BALL 3-WAY (PRESSURE SELECTOR)
1
15 3288-0020 VALVE, BALL (COMPRESSOR START-RUN)
6
16 9S01-0028 SCREW, MCH PH RD (1/4 x 3/4)
6
17 9W03-0004 LOCKWASHER (1/4)
6
18 9N01-0007 NUT (1 /4)
* = Not Shown

CONTROL PANEL - DRILLING FUNCTIONS
SEE ENGINE
• CONTROL PANEL
9.
111.1111 1
18 19
.1 I. •1
16 17 0 0
• •
240 0 26
S CENIIMO S
23
• • 200 210 22 25 CD
00 0 000 0
28 29 30 31 32 33 35
0
41
36 37 38 39
40 0
000 0
4-3
0336G 3/88
CONTROL PANEL
REF. NO.
NO. PART NUMBER DESCRIPTION REO
1 3451-0107 SUPPORT, VALVE 1

2 2966-0058 DOOR, ACCESS (LH) 1
3 2966-0048 DOOR, ACCESS (RH) (NOT SHOWN) 1
4 2029-0002 SCREW, TAPTITE (1/4 x 1/2) 10
5 0180-0033 LATCH, DOOR 2
6 0480-0250 COVER, PLATE CONTROL PANEL 1
(USED WHEN NO LAZY SUSAN)
7 9S01-0036 CAPSCREW (3/8 x 3/4) (ITEM 7-9 TO FASTEN COVER) 4
8 9W03-0006 LOCKWASHER (3/8) 4
9 9N01-0006 NUT (3/8) 4
10 2103-0028 LIGHT, UTILITY (12V) 2

Consisting of:
10A 2103-0039 BULB, 12 VOLT UTILITY (Patterson Mfg. Co. # 1141) 2
11 0923-0046 CONTROL, THROTTLE 12 FT (ENGINE SPEED) 1

12 2065-0045 GAUGE, HYD PRESSURE 0-6000 (ROTATION) 1
13 2065-0045 GAUGE, HYD PRESSURE 0-6000 (HOLDBACK) 1
14 2065-0044 GAUGE, HYD PRESSURE 0-3000 (DOWNFEED) 1
15 2072-0026 TACHOMETER (0-150 RPM) (ROTATION) 1
16 2065-0046 GAUGE, PRESSURE 0-2000 (WATER INJECTION) 1
17 2065-0046 GAUGE, PRESSURE 0-2000 (LUBRICATOR) 1
18 2767-0020 VALVE, HYD RELIEF 150-3000 PSI (HOLDBACK) 1
19 2767-0053 VALVE, HYD RELIEF 100-1500 PSI (DOWNFEED) 1
20 2261-0013 VALVE, FLOW CONTROL (WATER INJ RPM CONTROL) 1
21 0092-0005 VALVE, NEEDLE 1/4 ST (LUBRICATOR) 1
22 0092-0005 VALVE, NEEDLE 1/4 ST (FOAM) 1
23 3288-0030 VALVE, BALL 3-WAY 3000 PSI (ROTATION SPEED RANGE) 1
24 0923-0024 CONTROL LEVER ASY (AIR VALVE) 1
25 0923-0038 CONTROL CABLE 54 IN. TEE HANDLE (BLOWDOWN) 1
26 3288-0020 VALVE, BALL 1/4 300 (LUBRICATOR) 1
27 2525-0008 INDICATOR, LEVEL 1
28 SLOWFEED CONTROL
29 BREAKOUT CONTROL
30 JIB BOOM SWING (OPTIONAL)
31 JIB BOOM EXTEND (OPTIONAL)
32 LAZY SUSAN SWING (OPTIONAL)
33 LAZY SUSAN ROTATE (OPTIONAL)
34 WATER INJECTION CONTROL
35 WINCH CONTROL
36 FRONT OUTRIGGER CONTROL
37 LEFT OUTRIGGER CONTROL
38 RIGHT OUTRIGGER CONTROL
39 MAST TILT CONTROL
40 ROTATION DIRECTION CONTROL
41 RAPID FEED CONTROL

Printed in U.S.A.
4-4
OPERATOR PLATFORM
21 - 22 21-22
18
23
19
4-5
0313G 3/88
OPERATOR PLATFORM
REF. NO.
1 0898-0114 PLATFORM, OPERATOR 1

2 0877-0595 SUPPORT, PLATFORM (WELDED) 1
3 0914-0135 PIN, COTTERLESS 1
4 2017-0001 KEEPER WIRE ONLY (WELDED) 1
5 9M09-0003 CHAIN, BULL DOG #2 1'
6 0914-0136 PIN, PLATFORM PIVOT 2
7 9S01-0101 CAPSCREW (5/8 x 2-1/4) 2
8 9W01-0008 PLATEWASHER (5/8) 2
9 9W03-0010 LOCKWASHER (5/8) 2
10 9N01-0013 NUT (5/8). 2
11 3451-0107 SUPPORT, VALVE 1
12 0570-0111 PLATEWASHER (1-5/16 x 2-1/2) 2
13 0096-0001 PADLOCK 1
14 9S01-0007 CAPSCREW (1/4 x 1 ) 1
16 9W03-0004 LOCKWASHER (1/4) 1
17 9N01-0007 NUT,(1/4) 1
18 2966-0058 DOOR, ACCESS (L.H.) 1
19 0180-0033 DOOR, LATCH 2
20 2029-0002 SCREW, TAPTITE (1/4 x 1/2) 8
21 2103-0028 LIGHT, PANEL 2
22 2103-0042 BULB, BAYONET (GE # 1665) 2
23 2966-0048 DOOR, ACCESS (R.H.) 1

Printed in U.S.A.
4-6
HELPERS PLATFORM
13
4-7
0300G 3/88
HELPERS PLATFORM
REF. NO.
REQ.
1 0898-0115 PLATFORM, OPERATOR (RH) 1

2 0877-0882 SUPPORT, PLATFORM 1
3 0914-0135 PIN (1/2 x 1-1/2 COTTERLESS) 1
4 2017-0001 KEEPER, WIRE ONLY (WELDED) 1
5 9M09-0003 CHAIN, BULL DOG (#2) 1'
6 0914-0136 PIN, PLATFORM PIVOT 2
7 9S01-0101 CAPSCREW (5/8 x 2-1/4) 2
8 9W01-0008 PLATEWASHER (5/8) 2
9 9W03-0010 LOCKWASHER (5/8) 2
10 9N01-0013 NUT (5/8) 2
11 0877-0880 SUPPORT, PLATFORM (WELDED TO FRAME) 1
12 0862-0279 BRACKET, PLATFORM MTG 1
13 0898-0123 PLATFORM, WALKWAY 2
14 9S01-0007 CAPSCREW (1/4 x 1) 1
16 9W03-0004 LOCKWASHER (1/4) 1
17 9N01-0007 NUT (1/4) 1
18 0096-0001 PADLOCK 1
19 0570-0111 PLATEWASHER (1-5/16 x 2-1/2) 2

Printed in U.S.A.
4-8
OUTRIGGER CIRCUIT
•
FOR OUTRIGGER CYLINDER TO
CHECK VALVE HOSES SEE ITEMS
28 TO 32
12
6
10
27
„ op R
25 C .' 0
S.0 i\‘ Cfr
gfr. \CI`tk 't 09‘•
VC" \4
21
20
I8A
FOR OUTRIGGER VALVE

19
TO CHECK VALVE
HOSES SEE
ITEMS 33 T035
23
1%.
36
•cd
oklis
Q‘)
4-9
3/88
0326G
OUTRIGGER CIRCUIT
NO.
REF. DESCRIPTION
NO. PART NUMBER REO.
CYLINDER, HYD (4 x 2 x 41) 3

1 2813-0201
2 3332-0065 CONNECTOR (1/4FP x 1/4M37) 3
VALVE, FLOW CONTROL (1/2 x 20 GAL) 3
3 2261-0009
3897-0001 TUBE, REDUCING ST ADPT 37° (1/2 x 1/4) 3
4
NUT, TUBE (37 FLARE) 3
5 3890-0003 3
6 2250-0011 VALVE, CHECK (3/8P)
SUPPORT, CHECK VALVE 3
7 3147-0011 6
8 9501-0024 CAPSCREW (5/16 x 1-3/4)
LOCKWASHER (5/16) 6
9 9W03-0005 6
10 9W01-0004 PLATEWASHER (5/16)
11 3332-0053 3
12 3332-0102 CONNECTOR (3/8MP x 1/4M37) (.086 RESTRICTED)
TEE, SER DS (3/8MP x 3/8FP x 3/8FP) 3
13 3336-0002
NIPPLE, CLOSE X-HVY DS (3/8MP) 3
14 3337-0008 3
15 2767-0042 VALVE, RELIEF (2500 PSI)
16 3332-0054 3
17 3896-0002 TEE (3/8M37 x 3/8F37 x 3/8M37)
VALVE ASY, HYDRAULIC 1

18 2258-0182 *
Consisting of:
VALVE SECTION, INLET (Husco # 5001-A-1) 1
18A 2259-0060 *
VALVE ASY, RELIEF (Husco # 5060) 1
5000-8751
VALVE SECTION, CYLINDER (Husco # 5002-A-1) 4
18B 2259-0061 *
3030-0216 VALVE SECTION REPAIR KIT
Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
POPPET, LOAD CHECK 1
SPRING, LOAD CHECK 1
VALVE SECTION, OUTLET (Husco # 5003-A-4) 1

18C 2259-0065 *
CAPSCREW (3/8 x 1-1/4) 4
19 9S01-0038 4
20 9W03-0006 LOCKWASHER (3/8)
NUT (3/8) 4
21 9N01-0009 4
22 2916-0110 LEVER, ST
TEE (5/BMOA x 1/2M37 x 1/4M37) 1
23 3885-0012 1
24 3889-0001 CAP (1/4F37)
CONNECTOR (5/8M0 x 1/2M37) 2
25 3332-0014 6
26 3332-0057 CONNECTOR (1/2M0 x 3/8M37)
3
27 2826-0578 HOSE, HYD 3/8 x 16 100R2 590
HOSE, HYD 1/4 x 36 100R1 S90 1
28 2826-0533
(LH REAR OUTRIGGER ROD END TO CHECK VALVE)
HOSE, HYD 1/4 x 38 100R1 S90 1
29 2826-0901
(LH REAR OUTRIGGER BUTT END TO CHECK VALVE)
HOSE, HYD 1/4 x 22 100R1 S90 1
30 2826-0365
(RH REAR OUTRIGGER BUTT END TO CHECK VALVE)

Printed in U.S.A.
4-10
0326G 3/88
OUTRIGGER CIRCUIT
REF. NO.
31 2826-0370 HOSE, HYD 1/4 x 20 100R1 S90 1

(RH REAR OUTRIGGER ROD END TO CHECK VALVE)
32 2826-0429 HOSE, HYD 1/4 x 13 100R1 S90 2
(FRONT OUTRIGGER TO CHECK VALVE)
33 2826-0476 HOSE, HYD 3/8 x'415 100R2 37S 2
(OUTRIGGER VALVE TO SINGLE FRONT OUTRIGGER
CHECK VALVE)
34 2826-0904 HOSE, HYD 3/8 x 32 100R2 S90 2
(OUTRIGGER VALVE TO LEFT REAR OUTRIGGER CHECK
VALVE)
35 2826-0906 HOSE, HYD 3/8 x 114 100R2 37S 2
(OUTRIGGER VALVE TO RIGHT REAR OUTRIGGER CHECK
VALVE)
36 2826-0910 HOSE, HYD 1/2 x 180 100R2 590 1
37 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S 1
38 2826-0364 HOSE, HYD 1/2 x 26 100R2 S90 1
* = See Operator's/Maintenance Manual

for detailed information.
SCHRAMM, INC., West Chester. PA ALWAYS GIVE EQUIPMENT SERIAL

Printed In U S.A. NUMBER WHEN ORDERING PARTS.
4-11
•
•
BREAKOUT WRENCH CIRCUIT
25
27 +OAP
0- iv 8
10 o
fee 504141po, ci" je
II
TO TEE IN RETU
PORT, OF WATE INJ, VALVE 2
-
11
14:
le#411111
••••
1111
4‘
coc`glik%'
9 4,0' AO"
.co 4,1?'
ik5)
CP2
4C" 26
S
4V' 21 13
c 20
s° 14
15
FROM HYDRAULIC 23
TANK Ra
4-12
3/88
0258G
BREAKOUT WRENCH CIRCUIT
NO.
REF. DESCRIPTION
PART NUMBER RED.
NO.
.--r CVr-
1 2813-0011 CYLINDER, HYD (3 x 1.5 x 8)
2 3892-0003 ELBOW, 90° (1/2F37 x 1/2M37)
3 3332-0026 CONNECTOR (1 /4MP x 1/4M37)
4 3892-0001 ELBOW, 90° (1/4F37 x 1/4M37)
r
5 2258-0211 * VALVE ASY, HYDRAULIC (HI-PRESSURE)
Consisting of:
rr-
5A 2259-0060 * VALVE SECTION, INLET (Husco # 5001-A-1)
5000-8751 VALVE ASY, RELIEF (Husco # 5060)
r
58 2259-0078 * VALVE SECTION, CYLINDER DETENTED
(Husco # 5002-DA5)
r
5C 2259-0077 * VALVE SECTION, CYLINDER W/PORT RELIEFS
(Husco #5002-DA5)
Consisting of:
C \I (NJ tNI r- ir
SEAL, WIPER
SEAL, SPOOL
0-RING, SECTION
POPPET, LOAD CHECK
SPRING, LOAD CHECK
r cl- e rrt GNI

5D 2259-0065 * VALVE SECTION, OUTLET (Husco # 5003-A-4)
6 9S01-0038 CAPSCREW (3/8 x 1-1/4)

7 9W03-0006 LOCKWASHER (3/8)
8 9N01-0009 NUT (3/8)
9 2916-0110 LEVER, ST
N CV
10 3346-0013 PLUG (5/8M0)
11 3332-0014 CONNECTOR (5/8M0 x 1 /2M37)
12 3854-0001 CONNECTOR (1/2FP x 1/2F37)
13 3337-0011 NIPPLE, CLOSE X-HVY DS (1/2MP)
14 2767-0054 VALVE, HYD RELIEF
15 3852-0003 TEE (1/2MP x 1 /2M37 x 1/2M37)
16 3897-0003 TUBE, REDUCER ST ADPT 37° (1/2 x 3/8)
17 3890-0003 NUT, TUBE (37 FLARE)
18 3854-0004 CONNECTOR (3/8FP x 3/8F37)
20 2253-0023 REGULATOR, HYD PRESSURE
21 3332-0044 CONNECTOR (3/8M0 x 1/4M37)
CV r- t--NCVC\ I
22 3332-0067 CONNECTOR (1/2M0 x 1/4M37)

23 2826-0912 HOSE, HYD 1/2 x 190 100R2 S90
24 2826-0389 HOSE, HYD 1/2 x 28 100R2 37S
25 2826-0600 HOSE, HYD 1/4 x 300 100R1 37S
26 2826-0540 HOSE, HYD 1/4 x 16 100R1 590
27 5000-8751 VALVE, RELIEF (1500 - 3000 PSI) (Husco # 5060)

ALWAYS GIVE EQUIPMENT SERIA L
WINCH CIRCUIT
(WITH BRADEN PD5.8 WINCH)
21
17
15
14
I3
TO TEE ON
24 19 , GEAR BOX RETURN
13;:::: 21
2050 23
'
sva
o II
21
• •
I0
•
•
II
22
'001 12
Age
7
22 27
OPTIONAL -POWER
BEYOND TO JIB
BOOM VALVE
TO HYD.
MANIFOLD
FROM OUTRIGGER
VALV E
27
FROM PB PORT OF
OUTRIGGER VALVE
4-14
3/68
0328G
WINCH CIRCUIT
(WITH BRADE N PD5.8 WINCH)
NO.
REF. DESCRIPTHDN
PART NUMBER REQ.
NO.
VALVE ASY, HYDRAULIC 1

1 2258-0207 *
Consisting of:
lA 2259-0060 * 1
VALVE ASY, RELIEF (Husco # 5060)
VALVE SECTION (Husco # 5002-A-10) 1

18 2259-0063 *
Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2

1C 2259-0065 *
CAPSCREW (3/8 x 1-1/4) 4
2 9S01-0038 4
3 9W03-0006 LOCKWASHER (3/8)
NUT (3/8) 4
4 9N01-0009 1
5 3385-0012 TEE (5/BMOA x 1/2M37 x 1/4M37) 1
6 3889-0001 CAP (1/4F37)
1
7 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 2
8 3346-0013 PLUG (5/8M0)
2
9 3332-0057 CONNECTOR (5/8M0 x 3/8M37) 2
10 3879-0037 TUBING ASY, HYD 37° (1/2 x 142) 4
11 3864-0008 CONNECTOR (1/2M37 x 3/8M37) 6
12 3312-0022 CLAMP ASY, TUBING (1/2 OD) 4
14 9W03-0008 LOCKWASHER (1/2) 4
15 9N01-0011 NUT (1 /2)
2
16 3332-0110 CONNECTOR (1MO x 3/8M37) 2
17 3892-0002 ELBOW, 90° (3/8F37 x 3/8M37)
1
18 2826-0364 HOSE, HYD 1/2 x 26 100R2 590 1
19 3332-0075 CONNECTOR (1/8MP x 1 /4M37) 1
20 3892-0001 ELBOW, 90° (1 /4F37 x 1/4M37)
2
21 2826-0732 HOSE, HYD 3/8 x 80 100R2 S90 2
22 2826-0736 HOSE, HYD 3/8 x 111 100R2 37S 1
23 2826-0840 HOSE, HYD 1/4 x 80 100R1 S90 1
24 3317-0003 CABLE, WINCH (7/16 x 150')
1
25 1120-0058 * WINCH, PLANETARY (Braden # PD5.8-29020-01)
(WITH 1.96 IN3/REV COMMERCIAL GEAR MOTOR)
5000-9745 KIT, WINCH REPAIR (Braden # 61774)
1
26 2916-0110 LEVER, ST 2
27 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S 1
28 2826-0846 HOSE, HYD 1/2 x 130 100R2 37S 1
29 3896-0003 TEE (1 /2F37 x 1/2M37 x 1/2M37)


WINCH CIRCUIT
(WITH GEAR PRODUCTS PG105 WINCH)
15
14
13
FROM OUTRIGGER
VALVE
FROM PB PORT OF
OUTRIGGER VALVE
4-16
0323G 3/88
WINCH CIRCUIT
NO.
REF. DESCRIPTION
NO. PART NUMBER REQ.
1 2258-0207 * VALVE ASY, HYDRAULIC

Consisting of:
1A 2259-0060 * VALVE SECTION, INLET (Husco # 5001-A-1) 1
5000-8751 VALVE ASY, RELIEF (Husco # 5060) 1
18 2259-0063 * VALVE SECTION (Husco # 5002-A-10) 1

Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
1C 2259-0065 * VALVE SECTION, OUTLET (Husco # 5003-A-4) 1
2 9S01-0038 CAPSCREW (3/8 x 1-1/4) 4

3 9W03-0006 LOCKWASHER (3/8) 4
4 9N01-0009 NUT (3/8) 4
5 3885-0012 TEE (5/BMOA x 1/2M37 x 1/4M37) 1
3889-0001 CAP (1/4F37) 1
6
7 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 2
3896-0003 TEE (1/2F37 x 1/2M37 x 1/2M37) 1
8
9 3332-0057 CONNECTOR (1/2M0 x 3/8M37) 2
3879-0037 TUBING ASY, HYD 37° (1/2 x 142) 2
10
11 3864-0008
3312-0022 CLAMP ASY, TUBING (1/2) 6
12 8
13 0978-0035 CAPSCREW (5/8 x 2 - SAE GRADE 5)
14 9W02-0007
9W03-0010 LOCKWASHER (5/8) 8
15 2
16 3886-0007 CONNECTOR, LONG (5/8M0 x 3/8M37)
1120-0029 * WINCH (Gear Products # PG105-00058-1) 1

17
Includes:
2999-0061 * MOTOR, HYD (Ross # MAB16-002) 1
17A
5000-9532 MOTOR SEAL KIT (Ross # MAB500003)
Consisting of:
SEAL 1
RING, RETAINING 1
WASHER, BACKUP 1
SEAL 1
RING, SEAL 2
3317-0003 CABLE, WINCH (7/16 x 150') 1

18 1
19 3346-0013 PLUG (5/8M0)
2916-0110 LEVER, ST 1
20 2
21 2826-0655 HOSE, HYD 3/8 x 36 100R2 S90
HOSE, HYD 3/8 x 111 100R2 37S 2
22 2826-0736

SCHRAMKINC,WesWiester,PA NUMBER WHEN ORDERING PARTS
0323G 3/88
WINCH CIRCUIT
REF. NO.
23 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S 2

24 2826-0846 HOSE, HYD 1/2 x 130 100R2 S90 1
25 2826-0364 HOSE, HYD 1/2 x 26 100R2 S90 1


PrimecHnU.S.A. NUMBER WHEN ORDERING PARTS.
4-18
•
•
MAST TILT CYLINDERS CIRCUIT
4-19
0285G 3/88
MAST TILT CYLINDER CIRCUIT
REF. NO.
NO.
1 2813-0198 CYLINDER, HYDRAULIC (5 x 2-1/2 x 37) CUSH 2

2 3416-0020 PIN (1.618 x 7-1/4) 2
3 3417-0001 PIN (1.618 x 8-1/8) 2
4 9S02-0046 CAPSCREW (1/2NF x 3-1/2) 2
5 0374-0005 LOCKNUT (1/2 NF) 2
6 2213-0001 FITTING, GREASE 65 (1/8P) 4
7 3332-0032 CONNECTOR (1/2M0 x 1/2FP) 2
9 2250-0010 VALVE, CHECK (1/2P) 2
10 3332-0060 CONNECTOR (1/2MP x 3/8M37) 2
11 3332-0057 CONNECTOR (1/2M0 x 3/8M37) 2
12 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S 1
13 9501-0079 CAPSCREW (1/2 x 3-1/4) 2
14 9N06-0004 NUT, JAM (1/2) 2
15 2258-0182 * VALVE ASY, HYDRAULIC 1

Consisting of:
15B 2259-0061 * VALVE SECTION, CYLINDER (Husco # 5002-A-1) 4

Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
15C 2259-0065 * VALVE, SECTION, OUTLET (Husco # 5003-A-4) 1
16 9501-0038 CAPSCREW (3/8 x 1-1/4) 4

17 9W03-0006 LOCKWASHER (3/8) 4
18 9N01-0009 NUT (3/8) 4
19 3885-0012 TEE (5/8M0 x 1/2M37 x 1/4M37) 1
20 3889-0001 CAP (1/4F37) 1
21 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 2
22 3332-0057 CONNECTOR (1/2M0 x 3/8M37) 2
23 3346-0013 PLUG (5/8M0) 1
24 3896-0002 TEE (3/8F37 x 3/8M37 x 3/8M37) 2
25 2826-0364 HOSE, HYD 1/2 x 26 100R2 S90 1
26 2916-0110 LEVER, ST 4
27 2826-0908 HOSE, HYD 3/8 x 96 10082 37S 1
28 2826-0522 HOSE, HYD 3/8 x 129 100R2 S90 1
29 2826-0735 HOSE, HYD 3/8 x 105 100R2 37S 1
30 2826-0907 HOSE, HYD 3/8 x 144 100R2 S90 1
31 2826-0910 HOSE, HYD 1/2 x 180 100R2 S90 1

• ALWAYS GIVE EQUIPMENT SERIAL

Printed in V.S.A. 4-20
•
ROTATION GEARBOX CIRCUIT
20
19
B
13
si
12 AAR,- I
53
3 CD
18 63
10
2 62
1161 2
63 %moss,
14 V 1.
V .2 --trar 2
3 1
64
15
17 i6
2 21 62 25
53
62
66
64
4 26
2
Sil
hE A?
5 25
22 1/4, .1'11/31.
1 (44
TO ROTATION
GEARBOX 'A' 65
D 23 s%4 27
67 •
28 ,„29 68 30
67 t „ 68•.C 29
cilr
4? ,•.,,30f;c".4%*
k.s. 29
FROM
, 3:. l
.
WINCH
38
39
r 41 . 58 ♦
Th
32
-----...........?-... 10
40 4 12 _ <14,..%•/, 33
37 11 31
38 r al.tr:0
C42
41
67
42
65
42
13 34 61
TO AIR
36 55 30 29 VALVE
42
66 TO MANIFOLD
35 tw
TO CMX VALVE
f
f t 1eti
;: 2
41 Qr.
TO CMX FROM PILOT
VALVE 60
VALVE
TO PRESSURE REG '
SLOW FEED -- A s. 57
VALVE 51
4
59
go,
50 •rt 53
\g 6
• „.
1/4' 49 54 46 45
51
4
411111ta 47
49 _ e ib\is 4
2 19 45
48
ROTATION SPEED RANGE VALVE
ROTATION DIRECTION SELECTOR VALVE
4-21
0310G 3/88
REF. NO.
NO.
GEARBOX 2.26/1 W/29.9. CU. IN. MTRS 1

1 0870-0102
3332-0034 CONNECTOR (IMO x 1/2M37) 4
2
3 3332-0011 CONNECTOR (1/4M0 x 1/4M37) 2
TEE (1/4F37 x 1/4M37 x 1/4M37) 4
4 3896-0001
2927-0022 CONNECTOR, PACKING GLAND AIR 1
5
VALVE ASY., ROTATION DIRECTIONAL CONTROL 1

6 2258-0215
Consisting of:
BODY, VALVE . 1
2258-0214
2258-0175 CARTRIDGE, DIRECT IONAL CONTROL VALVE 1
PLUG (1/2M0) 1
3346-0012
CAPSCREW (3/8 x 5-3/4 - SAE GRADE 5) 4

7 0978-0272
8
LOCKNUT (3/8) 4
9 0374-0033
BOLT, U (5/16 x 2-13/16) 6
10 1018-0008
LOCKWASHER (5/16) 12
11 9W03-0005
12 9W02-0003
NUT (5/16) 12
13 9N01-0008
SUPPORT, HOSE 1
14 2551-0126
CAPSCREW (1/2 x 1-1/4) 4
15 9501-0071
PLATEWASHER (1/2) 4
16 9W01-0007
LOCKWASHER (1 /2) 4
17 9W03-0008
BOLT, U (1/4 x 1-11/16) 1
18 1018-0027
LOCKWASHER (1/4) 2
19 9W03-0004
NUT (1/4) 2
20 9N01-0007 4
21 3332-0013 CONNECTOR (1/2M0 x 1/2M37)
1
22 3886-0003 CONNECTOR, LONG (3/4M0 x 3/4M37)
23 3332-0035 1
24 3332-0011 CONNECTOR (1/4M0 x 1/4M37)
2
25 3332-0054 CONNECTOR (3/8MP x 1 /4M37)
VALVE, RELIEF (3/8 - 25 PSI) 1
26 2767-0031 1
27 2927-0001 JOINT, SWIVEL (2 BRONZE 90°)
CONNECTOR (2MP x 2FPS) 2
28 2220-0008 1
29 3045-0001 PROTECTOR, AIR HOSE
1
30 0045-0008 CHAIN, SAFETY (W/CLAMP 2-1/2)
1
31 0045-0007 CLAMP, PIPE (2 DIA.)
LINE ASY, AIR (2 IN.) 1
32 0814-0008 1
33 3341-0010 ELBOW, 90° HIGH PRESSURE SERVICE (2FP x 2FP)
1
34 2221-0057 ELBOW, 90° (2MP x 2FPS)
1
35 0896-0139 GUARD
6
36 2029-0002 SCREW, TAPTITE (1/4 x 1/2)
2
37 3880-0035 TUBING ASY., HYD (3/4)
2
38 3880-0036 TUBING ASY., HYD (1/2)
6
39 3312-0023 CLAMP ASY., TUBING (3/4)
6
40 3312-0022 CLAMP ASY., TUBING (1/2)
4
41 3864-0007 CONNECTOR (3/4M37 x 3/4M37)
4
42 3864-0003 CONNECTOR (1/2M37 x 1/4M37)
1
43 9E03-0018 SLEEVE, NYLON 2-3/8 ID (INSTALLED OVER ROTATION
HOSES)

0310G 3/88
REF. NCL
44 3288-0030 VALVE, BALL 3-WAY (3000 PSI - 1/4P) 1

45 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 2
46 3332-0026 CONNECTOR, (1/4MP x 1/4M37) 1
47 2258-0225 * VALVE, HYDRAULIC HRC FRICTION-LOCK 1

(Husco # 7470-A-15 WITH # 52524 FRICTION LOCK
( & # 51969 STUD)
3030-0217 HRC REPAIR KIT
Consisting of:
PLUG, SAE 2
0-RING 2
HANDLE, BOOT 1
48 9501-0006 CAPSCREW (1/4 x 3/4) 2

49 3883-0002 ELBOW, 90° (3/8MOA x 1/4M37) 2
50 3332-0044 CONNECTOR (3/8M0 x 1/4M37) 1
51 2826-0877 HOSE, HYD 1/4 x 43 100R1 S90 1
52 2826-0540 HOSE, HYD 1/4 x 16 100R1 S90 2
53 2826-0587 HOSE, HYD 1/4 x 31 100R1 S90 2
54 2826-0438 HOSE, HYD 1/4 x 140 100R1 37S 1
55 2826-0399 HOSE, HYD 1/4 x 180 100R1 S90 1
56 2826-0902 HOSE, HYD 1/4 x 130 100R1 37S 1
57 2826-0561 HOSE, HYD 1/4 x 24 100R2 37S 1
58 2826-0840 ** HOSE, HYD 1/4 x 80 100R1 S90 1
59 2826-0369 HOSE, HYD 1/4 x 16 100R1 37S 2
60 2826-0893 HOSE, HYD 3/4 x 115 5000 PSI 37S 2
61 1184-0074 HOSE ASY, AIR (2 x 84) 1
62 2826-0887 HOSE, HYD 1/2 x 32 M2T S90 2
63 2826-0888 HOSE, HYD 1/2 x 26 M2T S90 2
64 2826-0429 HOSE, HYD 1/4 x 13 100R1 S90 1
65 2826-0889 HOSE, HYD 1/4 x 226 100R1 S90 1
66 2826-0890 HOSE, HYD 1/4 x 220 100R1 S90 1
67 2826-0891 HOSE, HYD 3/4 x 206 5000 PSI S90 2
68 1184-0037 HOSE ASY, HYD (2 x 201) 1

** = Needed with some winch models

Printed in U.S.A. NUMBER WHEN ORDERING PARTS
4-23
0
•
TRAVERSE CYLINDER CIRCUIT
TO RAPID
FEED VALVE
4-24
031% 3/88
TRAVERSE CYLINDER CIRCUIT
REF. NO.
NO.
2813-0197 CYLINDER ASY, HYD (4-1/2 x 2-1/2 x 165) 2

3886-0004 CONNECTOR, LONG (IMO x 1M37) 2
3332-0018 CONNECTOR (IMO x 1M37) 2
3892-0006 ELBOW, 90° (1F37 x 1M37) 4
2
lf) to N. CO
3896-0006 TEE (1F37 x 1M37 x 1M37)

3880-0040 TUBING ASY, HYD 37° BD (1 OD) 2
3893-0006 ELBOW, 45° (1F37 x 1M37) 2
2826-0894 HOSE, HYD I x 111 4000 PSI 37S 2
SCHRAMM, INC., West Chester, PA • ALWAYS GIVE EOU

ROTATION DIRECTION CONTROL (CMX) VALVE CIRCUIT
•
STT UBING
0 TOM A
n.)
20
TO ROTATION
CONTROL VALVE
TO ROTATION
GAUGE
TO ROTATION
PUMP
4-26
3/88
0288G
ROTATION DIRECTION CONTROL (CMX) VALVE CIRCUIT
N O.
REF. DESCRIPTION RE Q
PART NUMBER
NO.
VALVE, HYDRAULIC (Vickers # CMX160-F2-S-11-690535) 1

1 2258-0199 *
5000-9660 CMX REPAIR KIT (Vickers # 920366)
Consisting of:
0-RINGS 16
GASKET 2
RINGS, BACKUP 3
3
2 0252-0028 CAPSCREW, HT (M12 x 1.75 x 30mm)
3
3 9W03-0008 LOCKWASHER (1/2)
3
4 0995-0124 FLANGE, HYD (3/4 TUBE x 3/4 PAD 6000)
3
5 2764-0078 0-RING (.210 x 1.975)
12
6 9S03-0029 CAPSCREW, SKT (3/8 x 1-3/4)
1
7 0995-0013 FLANGE, HYD (1 NPT x 1-1/4 PAD)
1
8 2764-0036 0-RING (.139 x 1.484)
4
9 9S03-0014 CAPSCREW, SKT (7/16 x 1-3/4)
1
10 3332-0016 CONNECTOR (3/4M0 x 3/4M37)
1
11 2826-0916 HOSE, HYD 3/4 x 185 5000 PSI 37S
1
12 3885-0009 TEE (3/4MOA x 3/4M37 x 1/4M37)
1
13 3892-0005 ELBOW, 90° (3/4F37 x 3/4M37)
1
14 3877-0004 ELBOW, 90° (1MP x 1M37)
3
15 3883-0002 ELBOW, 90° (3/8MOA x 1/4M37)
1
16 2826-0369 HOSE, HYD 1/4 x 16 100R1 37S
1
17 2826-0561 HOSE, HYD 1/4 x 24 100R2 37S
1
18 2826-0414 HOSE, HYD 1/4 x 48 100R1 37S
1
19 2826-0652 HOSE, HYD 1/4 x 168 100R1 37S
2
20 2826-0893 HOSE, HYD 3/4 x 115 5000 PSI 37S
1
21 2826-0918 HOSE, HYD 1 x 124 100R2 37S


RAPID FEED CIRCUIT
B
20 Is
TO MANIFOLD
FROM HOLDBACK
REGUL ATOR
TO TRAVERSE
CYLINDER
TO TRAVERSE
FROM RAPID
CYLINDER
FEED PUMP
FROM DOWNFEED
REGULATOR
4-28
3/88
0286G
RAPID FEED VALVE CIRCUIT
NO.
PARTNUMBER
NO.
1
1 2258-0206 * VALVE, HYDRAULIC
(Commercial Shearing P/N 48-9201-477)
(Comm. Code # VG35AA880-2HA811-2ZT980)
Consisting of: 1
-003)
lA 2259-0081 * VALVE SECTION, INLET (Comm. P/N 348-9195 1
VALVE ASY, RELIEF (Comm. P/N 355- 9107 -385)
5000-9746
EFS 1
18 2259-0075 * VALVE SECTION, CYLINDER SPOOL W/PORT RELI
(Comm. P/N 348-9192-073) 2
-115)
5000-9690 VALVE ASY, PORT RELIEF (Comm P/N 355-9001
(Comm. P/N 391-1803-722)
Consisting of:
3
SEAL, SQ SECTION (1-3/4 x 1-9/16) 1
SEAL, SQ SECTION (2 x 13/16)
1
0-RING, CHECK (1-1/1 6 x 15/16)
2
RING, BACKUP
2
0-RING (1-1/8 x 7/8)
-046) 1
1C 2259-0080 * VALVE SECTION, OUTLET (Comm. P/N 348-9106
2
2 9S01-0076 CAPSCREW (1/2 x 2-1/2) 2
3 9W03-0008 LOCKWASHER (1/2) 2
4 9N01-0011 NUT (1/2) 1
5 9S01-0064 CAPSCREW (7/16 x 2) 1
6 9W03-0007 LOCKWASHER (7/16) 1
7 9N01-0010 NUT (7/16) 2
8 3332-0018 CONNECTOR (1M0 x 1M37) 2
9 3885-0004 TEE (1MOA x 1M37 x 1M37) 1
10 2826-0655 HOSE, HYD 3/8 x 36 100R2 S90 1
11 2826-0909 HOSE, HYD 3/8 x 48 100R2 S90 2
12 3897-0004 TUBE, REDUCING ST ADPT (1 x 1/2) 2
13 3890-0006 NUT, TUBE (37 FLARE) 2
14 3897-0003 TUBE, REDUCING ST ADPT (1 /2 x 3/8) 2
15 3890-0003 NUT, TUBE (37 FLARE) 1
16 3346-0007 PLUG (1140) 1
17 3346-0014 PLUG (1-1/4M0) 1
18 2916-0112 HANDLE, VALVE 1
19 2826-0919 HOSE, HYD 1 x 154 5000 PSI 37S 1
20 2826-0627 HOSE, HYD 1 x 142 100R2 S90 2
21 2826-0894 HOSE, HYD 1 x 111 4000 PSI 37S
* See Operator's/Maintenance Manual


SCHRAMMJNC,WestOlester,PA NUMBER WHEN ORDERING PARTS.
WATER INJECTION CIRCUIT
(continued on page 4-33)
TO COOLER
THERMOSTAT
FROM
FROM SLOW HYD.PUMP
FEED VALVE
WATER INJECTION
PUMP HYD-
MOTOR
13
4-30
3/88
0281G
NO.
NO. PART NUMBER
1
1 2258-0209 * VALVE ASY, HYDRAULIC
Consisting of:
1A 2259-0060 * 1
5000-8751 VALVE, RELIEF (Husco # 5060)
VALVE SECTION, DETENTED (Husco # 5002-A-11) 1

18 2259-0064 *
Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
SEAL, SECTION 2

1C 2259-0065 *
4
2 9S01-0038 CAPSCREW (3/8 x 1-1/4) 4
3 9W03-0006 LOCKWASHER (3/8) 4
4 9N01-0009 NUT (3/8) 1
5 2916-0110 LEVER, ST 1
6 3885-0012 TEE (5/8M0 x 1/2M37 x 1/4M37) 1
7 3889-0001 CAP (1/4F37) 1
8 3332-0015 CONNECTOR (5/8M0 x 3/4M37) 1
9 3896-0005 TEE (1/2F37 x 1/2M37 x 1/2M37) 2
10 3346-0013 PLUG (5/8M0) 2
11 3332-0013 CONNECTOR (1/2M0 x 1/2M37) 1
12 2261-0013 VALVE, FLOW CONTROL 2
13 9S01-0012 CAPSCREW (1/4 x 2-1 /2) 2
15 0374-0003 LOCKNUT (1/4) 3
16 3883-0004 ELBOW, 90° (1/2MOA x 1/2M37)
1
17 2999-0063 * MOTOR, HYDRAULIC (Char-Lynn # 104-1037)
(Char-Lynn 2000 SERIES 4.9 CU.IN./REV)
5000-8652 KIT, SEAL (Char-Lynn # 61252)
Consisting of:
SEAL, DUST 1
SEAL, 3" ID 3
SEAL, SHAFT 1
SEAL, SHAFT FACE 1
SEAL, 0-RING 5/1 6 ID 3
SEAL, 2-5/8 ID 1
SEAL, FACE INNER 1
SEAL, FACE OUTER 1
2
18 3883-0008 ELBOW, 90° (3/4MOA x 3/4M37) 1
19 2065-0046 GAUGE, PRESSURE (0-2000) 1
20 3332-0065 CONNECTOR (1/4FP x 1/4M37) 1
21 2826-0482 HOSE, HYD 1/2 x 125 100R2 37S

SCHRAMM, INC.. West Chester, PA NUMBER WHEN ORDERING PARTS
0281G 3/88
REF. NO.
RECL
22 2826-0724 HOSE, HYD 1/2 x 33 100R2 S90 2

23 2826-0911 HOSE, HYD 1/2 x 185 100R2 590 1
24 3896-0003 TEE (1/2F37 x 1/2M37 x 1/2M37) 1
25 2826-0644 HOSE, HYD 1/4 x 18 100R1 37S 1
26 2826-0337 HOSE, HYD 3/4 x 148 100R2 S90 1
27 3897-0002 TUBE, REDUCING ST ADPT (3/4 x 1/2) 1
28 3890-0005 NUT, TUBE (37 FLARE) 1
29 2826-0389 HOSE, HYD 1/2 x 28 100R2 37S 1
30 2826-0914 HOSE, HYD 1/2 x 115 100R2 37S 1


4-32
I
WATER AND FOAM INJECTION PUMP ASY.
27
‘33
,i4
=z=1:1 TO FOAM
32 CONTAINER
\N
18 '" 52
/ W31
429
13 14
17 28 a
47
hik 9 20 10
21 9
36
7 22
TO METERING
/2°20 VALVE
6
35 48
49
21 TO WATER DNJ
22 VALVE
TO AIR CON TINED ON

51 PAGE 4-30
VALVE
56
38 57 50
40 43
44
45
46
4-33
V./LI7t2
(10 GPM)
NO.
REF. PA R T N U MBE R DESCRIPTION REQ.
NO.
Cf,
1
1 0861-0056 * PUMP, WATER AND FOAM INJECTION
(MODEL 10153 PUMP W/PULSE PUMP MANIFOLD
AND V-SHAPED HOT CUPS. INCLUDES 06300
---- -->,\ PULSE PUMP.)
000-3747 KIT, HOT CUP REPAIR (Cat # 30300)
0- .......2 Consisting of: 3
V-SHAPED HOT CUP 6
0-RING, CYLINDER 3
COTTER PIN (M1.5 x 10) 1
SHEET,, INSTRUCTION
5000-7611 KIT, DISCHARGE VALVE (Cat # 30225)
Consisting of: 3
RETAINER, VALVE SPRING 3
SPRING, VALVE L.V
CYLI NDER 3
0-RI NG, 3
SEAT, DISCHARGE VALVE 3
VALVE, DISCHARGE 3
0-RING, DISCHARGE VALVE SEAT 1
SHEET, INSTRUCTION
5000-1285 KIT, SEAL REPLACEMENT (Cat # 30226)
Consisting of: 3
SEAL, BLUE-DOT 3
WICK 3
COTTER PIN -SS (M1.5 x 10) 2
PAPER, ABRASIVE 400 GRIT 1
SHEET, INSTRUCTION
5000-1286 KIT, SLEEVE & SEAL REPLACEMENT (Cat # 30227)
Consisting of: 3
SEAL, BLUE-DOT 3
e- WICK -
) _„ 3
COTTER PIN -SS (M1.5 x 10) 3
BARRIER SLIN GER -SS ,-
i.,/ 3
SLEEVE 6
0-RING, SLEEVE 1
SHEET, INSTRUCTION
1
2 5000-1287 KEY 1
3 0877-0753 SUPPORT, WATER INJ PUMP 1
4 2909-0030 ADAPTOR, PUMP 3.25 PILOT (WELDED TO SUPPORT)
(NOT SHOWN) 4
5 9S01-0036 CAPSCREW (3/8 x 3/4) 4
6 9W03-0006 LOCKWASHER (3/8) 4
7 9W01-0005 PLATEWASHER (3/8)

Printed in U.S.A.
4-34
0309G 3/88
(10 GPM)
REF. NO.
NO. RE Q.
r--
8 2999-0063 * MOTOR, HYDRAULIC (Char-Lynn # 104-1037)
(Char-Lynn 2000 SERIES CU. IN./REV)
5000-8652 KIT, SEAL (Char-Lynn # 61252)
Consisting of:
SEAL, DUST
Cc)
SEAL, 3" ID
SEAL, SHAFT
.— Cc)
SEAL, SHAFT FACE
SEAL, 0-RING 5/16 ID
SEAL, 2-5/8 ID
SEAL, FACE INNER
SEAL, FACE OUTER
5000-8212 MOTOR, KEY (Char-Lynn # 14193)
9 9507-0015 CAPSCREW, FCBR (1 /2 x 1-1/4)
CN.1C r--
10 9W03-0008 LOCKWASHER (1/2)
11 3883-0008 ELBOW, 90° (3/4MOA x 3/4M37)
12 0697-0084 COUPLING, ELASTOMERIC JAW (L-110)
13 0821-0028 GUARD, COUPLING
'et
14 2029-0004 SCREW, TAPTITE (5/16 x 3/4)
15 9P05-0028 ELBOW, 90° SERVICE (1MP x 1FP)
16 9P01-0017 BUSHING, REDUCING (1MP x 3/4FP)
17 9P08-0071 NIPPLE (3/4P x 10)
18 9P05-0022 ELBOW, 90° SERVICE (3/4MP x 3/4FP)
19 9P07-0011 TEE (3/4FP x 3/4FP x 3/4FP)
C\I NN
20 9P08-0055 NIPPLE, CLOSE X-HVY (3/4MP)
21 9P01-0010 BUSHING, REDUCING (3/4MP x 1/4FP)
22 0992-0002 COCK, DRAIN (1/4P)
23 2746-0002 STRAINER, PIPELINE (3/4P)
24 9P07-0032 TEE, SER (3/4MP x 3/4FP x 3/4FP)
25 2221-0039 CONNECTOR (3/4MF x 3/4MFS)
26 9P01-0013 BUSHING, REDUCING (3/4MP x 1/2FP)
27 3877-0002 ELBOW, 90° (1/2MP x 1/2M37)
29 3288-0014 VALVE, BALL (1/2P)
30 2221-0046 ELBOW, 90° (1/4FP x 1/4FPS)
31 3832-0001 ELBOW, 90° (1/4FP x 1/4M37)
32 3893-0001 ELBOW, 45° (1/4F37 x 1/4M37)
33 2018-0001 NIPPLE, HOSE (1 /4 x 1/4P)
34 9H01-0001
rch
HOSE, AIR (1/4 BLACK)

35 9P07-0012 TEE, SIDE OUTLET (3/4FP)
36 2767-0009
r--
VALVE, RELIEF (3/4P)

37 3332-0045 CONNECTOR (3/4MP x 1/2M37)
38 3896-0003 TEE (1 /2F37 x 1/2M37 x 1 /2M37)
40 3288-0029 VALVE, BALL 3-WAY (3/4P)
41 2221-0039 ELBOW, 90° (3/4MP x 3/4FPS)
42 3877-0006 ELBOW, 90° (3/4MP x 1/2M37)
43 3854-0001 CONNECTOR (1/2FP x 1/2F37)
44 3341-0004 ELBOW, 90° SERVICE DS (1/2MP x 1/2FP)
SCHRAMNLINC,WestChester,PA ALWAYS GIVE EQUIPMENT SERIAL

Printed in U.S.A. 4-35 NUMBER WHEN ORDERING PARTS
UJUVIa
(10 GPM)
NO.
R EF. DESCRIPTION R EQ
PART NUMBER
NO.
BUSHING, REDUCING DS (1/2MP x 3/8FP) 1

45 2558-0004
2050-0004 COUPLING, QUICK DISC SKT (3/8MP) 1
46
CAPSCREW (3/8 x 3-1/2) 4
47 9S01-0047
LOCKWASHER (3/8) 4
48 9W03-0006
NUT (3/8) 4
49 9N01-0009
SUPPORT, SINGLE FOAM JUG BIN 1
50 0877-0818
CONTAINER, 5 GAL PLASTIC 1
51 1121-0002
HOSE, HYD 1/4 x 120 100R1 37S 1
52 2826-0398
HOSE, HYD 1/2 x 18 100R2 37S 1
53 2826-0477
HOSE, HYD 1/2 x 115 100R2 37S 1
54 2826-0914
HOSE, HYD 1/2 x 125 100R2 37S 2
55 2826-0482
HOSE, HYD 1/2 x 115 100R2 37S 1
56 2826-0914
CAPSCREW (3/8 x 1-1/4) 2
57 9501-0038
NUT (3/8) 2
58 9NO2-0003
PUMP, PULSE (Cat # 06300) 1
59 5000-4391
VALVE, NEEDLE (1/4P) 1
60 0092-0005
KIT, VALVE PANEL MOUNTING (1/4) (NOT SHOWN) 1
61 2368-0001
SPACER (3/8 x 1-5/16 OD x 15/16 ID) (NOT SHOWN) 1
62 0822-0136
ELBOW, 90° (1/4MP x 1 /4M37) 2
63 3877-0001
HOSE, HYD 1/4 x 22 100R1 37S 1
64 2826-0895


Printed in U.S.A.
4-36
LUBR.ICATOR,ON-OFF VALVE AND METERING VALVE
S
4-37
0284G 3/88
LUBRICATOR, ON-OFF VALVE AND METERING VALVE
NO.
REF.
NO.
3288-0020 VALVE, BALL (1/4 3000) LUB ON-OFF 1

1
3877-0001 ELBOW, 90° (1 /4MP x 1/4M37) 4
2
3 3896-0001 TEE (1/4F37 x 1/4M37 x 1/4M37 1
2826-0398 HOSE, HYD 1/4 x 140 100R1 375 1
4
(PRESS SIDE OF VALVE TO LUBRICATOR)
HOSE, HYD 1/4 x 102 100R1 37S 1
5 2826-0416
(REG. TO LUB. BALL VALVE)
6 3877-0001 ELBOW, 90° (1/4MP x 1/4M37) 1
7 0092-0005 VALVE, NEEDLE (1/4) 1
SPACER 1
8 0822-0136
2368-0001 KIT, MOUNTING 1
9
2826-0416 HOSE, HYD 1/4 x 102 100R1 375 1
10
(PUMP OUTLET TO VALVE)
2826-0540 HOSE, HYD 1/4 x 16 100R1 375 1
11
(VALVE TO LUBRICATOR GAUGE)
HOSE, HYD 1/4 x 25 100R1 S90 1
12 2826-0800
(VALVE TO MAIN AIR LINE)
ELBOW, 90° (1 /8MP x 1/4M37) 1
13 3877-0011
LUBRICATOR ASY. W/CASE 9 GAL 1

14 2117-0010
Consisting of:
LUBRICATOR (NO TANK) 1
15 2117-0005
TANK, LUBRICATOR (ONLY) 1
16 2912-0020
CAP AND GAUGE ASY. 1
17 0598-0033
GASKET, CASE 1
18 3676-0001
PLUG, PIPE (3/4) 1
19 9P09-0009
CAPSCREW (5/16 x 1-1/4) 4
20 9S01-0022
SUPPORT, TANK 2
21 0877-0237
CAPSCREW (3/8 x 1-1/4) 4
22 9501-0038 4
23 9W03-0006 LOCKWASHER (3/8)
GAUGE, PRESS. 1
24 2065-0046
CONNECTOR (1 /4FP x 1/4M37) 1
25 3332-0065

HYDRAULIC TANK CONNECTIONS
st: 20
25
21
22 24
01.30 IT
'4% 4111. 111 11
%n 'Itch 23
23 26
24
I26 18 27
•
• 15
18 27
46 13
29
6
21 r) 14
19
22
28
19 1W
11 )
TO HYD• .
MANIFOLD
TO HYD• N,swit.SWIL"
MANIFOLD
Ls>
q
47 48 47
16
,TR CY/12 35
7:47
ez,
•- 34
••••
-.••••
col TO 2766-0116
HYD• PUMP THIRD
kit 6 SECTION •
10
t36 ter 11
7 9
•nr4 41
4 6 33
37 pre _c
gs 43
%?.•4
49 38
4
441 3 TO2766 -0114
•ek39 HYD.PUMP
12 1 42
•••
40 44
TO 2766-0114
HY D.P UMP
,.45
S Irs".11b
TO 2766-0116
HYD. PUMP
FIRST SECTION
TO 2766-0091 SECOND SECTION
HYD. PUMP
4-39
0321G 3/88
HYDRAULIC TANK CONNECTIONS
NO.
REF.
NO.
1 2912-0027 TANK, HYDRAULIC (100 GAL) 1

4 0374-0019 LOCKNUT (5/8) 4
5 2696-0002 GASKET, HYD TANK COVER 1
6 2248-0005 VALVE, GATE BR (2) 3
7 9P07-0031 TEE, SERVICE (2MP X 2FP x 2FP) 2
8 9P01-0037 BUSHING, REDUCING (2MP x 1-1/2FP) 4
10 2221-0035 ELBOW, 45° (1-1/4MP x 1-1/4FPS) 1
11 2221-0070 ELBOW, 45° (1-1/2MP x 1-1/2FPS) 2
12 2220-0007 CONNECTOR (1-1/2MP x 1-1/2FPS) 2
13 2328-0001 MAGNET (1 NPT - 23 IN. LG.) 1
14 0710-0008 CONNECTOR, AIR BREATHER 1
15 2298-0005 BREATHER, AIR SPIN-ON (Schroeder # ABF-3) 1
16 0598-0031 GAUGE, OIL LEVEL SIGHT 1
17 0277-0039 FILTER, OIL RT2 (10 MICRON) 2
18 2295-0020 ELEMENT, HYD OIL FILTER (Schroeder K10 ELEMENT) 4
19 5000-5275 GASKET, RT INTANK FILTER 2
20 9S01-0038 CAPSCREW (3/8 x 1-1/4) 8
21 9W03-0006 LOCKWASHER (3/8) 8
23 9P09-0028 PLUG, PIPE FLUSH (1/8P) 2
24 9P05-0001 ELBOW, 90° SERVICE (1/8MP x 1 /8FP) 2
25 2065-0013 GAUGE, HYD FILTER COND. INDICATOR 2
26 9P01-0030 BUSHING, REDUCING (1-1/2MP x 1-1/4FP) 2
27 2221-0045 ELBOW, 90° (1-1/4MP x 1-1/4FPS) 2
28 0480-0251 COVER, HYD TANK 1
29 9S01-0036 CAPSCREW (3/8 x 3/4) 4
30 9P09-0016 PLUG, SQ HD (1-1/2MP) 1
31 9P01-0028 BUSHING, REDUCING (1-1/2MP x 1FP) 1
32 9P09-0011 PLUG, SQ HD (1MP) 1
33 9P09-0020 PLUG, FLUSH (2MP) 1
34 9P09-0006 PLUG, SQ HD (1/2MP) 2
35 3877-0002 ELBOW, 90° (1/2MP x 1/2M37) 1
36 9P01-0035 BUSHING, REDUCING (2MP x 1FP) 1
37 9P08-0077 NIPPLE, CLOSE (1MP) 1
9P05-0028 ELBOW, 90° SERVICE (1MP x 1FP) 1
38
39 3288-0011 VALVE, BALL (1P) 1
40 9P09-0011 PLUG, SQ HD (1MP) 1
41 1313-0137 HOSE, SUCTION (1-1/4 x 31 NPT) 1
42 1313-0103 HOSE, SUCTION (1-1/2 x 17-1/2 NPT) 1
1313-0033 HOSE, SUCTION (1-1/2 x 40 NPT) 1
44 1
45 1313-0142 HOSE, SUCTION (1-1/2 x 39 NPT)
0655-0014 STRAINER, HYD INLINE 50 GAL (Vickers # OF3-16-10) 2
47
48 0655-0015 STRAINER, HYD INLINE 75 GAL (Vickers # OF3-20-10) 1
2826-0581 HOSE, HYD 1/2 x 56 100R2 37S 1
49

rifted in U.S.A.
4-40
HYDRAULIC RETURN MANIFOLD AND THERMAL CONTROL VALVE
FROM HYD OIL

COOLER
28
FROM TO INTAKE
FILTER
ROTATION TO
32 SPEED INTAKE TO HYD.
SELECTOR • FILTER OIL COOLER
23
FROM MAST 23
(43: CASE DRAIN
31
34 27
22
1%ia 41011/
18 19
17 tirret; 21
3 26
33
3
it 33
FROM 24
25
FROM RAPID FEED FROM WATER
CM X VALVE VALVE INJECTION
VALVE
4-41
0299G 3/88
HYDRAULIC RETURN MANIFOLD AND THERMAL CONTROL VALVE
NO.
REF.
NO.
1 0566-0061 MANIFOLD, HYDRAULIC 1

2 9501-0038 CAPSCREW (3/8 x 1-1/4) 4
3 9W03-0006 LOCKWASHER (3/8) 4
5 3877-0017 ELBOW, 90° (1MP x 1/2M37) 1
6 3877-0004 ELBOW, 90° (1MP x 1M37) 2
10 3852-0003 TEE (1/2MP x 1/2M37 x 1 /2M37) 1
11 3332-0029 CONNECTOR (1/2MP x 1/2M37) 1
12 3897-0001 TUBE, REDUCER ST ADPT (1/2 x 1/4) 1
13 3890-0003 NUT, TUBE (37 FLARE) 1
14 3896-0001 TEE (1/4F37 x 1/4M37 x 1/4M37) 1
15 3892-0001 ELBOW, 90° (1/4F37 x 1/4M37) 1
16 3337-0001 NIPPLE, REDUCING DS (1MP x 3/4FP) 1
17 3854-0002 CONNECTOR (3/4FP x 3/4F37) 1
18 3332-0019 CONNECTOR (1M0 x 3/4M37) 1
19 2157-0019 VALVE, THERMAL CONTROL (120 DEG.) 1
20 5000-7675 THERMOSTAT, 120 DEG (REPLACEMENT FOR ABOVE) 1
21 3332-0019 CONNECTOR HMO x 3/4M37) 1
22 3883-0010 ELBOW, 90° (1MOA x 3/4M37) 1
23 1313-0137 HOSE, COMPR 1-1/4 x 31 NPT 2
24 2826-0627 HOSE, HYD 1 x 142 100R2 S90 1
25 2826-0918 HOSE, HYD 1 x 124 100R2 37S 1
26 2826-0337 HOSE, HYD 3/4 x 148 100R2 S90 1
27 2826-0915 HOSE, HYD 3/4 x 70 100R2 37S 1
28 2826-0631 HOSE, HYD 3/4 x 76 100R2 37S 1
29 2826-0846 HOSE, HYD 1/2 x 130 100R2 S90 1
30 2826-0482 HOSE, HYD 1/2 x 125 100R2 37S 1
31 2826-0399 HOSE, HYD 1 /4 x 180 100R1 S90 1
32 2826-0438 HOSE, HYD 1 /4 x 140 100R1 37S 1
33 9N01-0009 NUT (3/8) 2
34 9S01-0048 CAPSCREW (3/8 x 3-3/4) 1

SLOW FEED CIRCUIT
25 1-&s.‘ IS)
e 0
s%-
TO TEE IN RETURN
PORT WATER
INJ. VALVC 22
TO HOLDBACK
REGULATOR
TO DOWN FEED —4ZEO
REGULATOR 23 21
TO 'P PORT
ROTATION
VALVE
TO 'R s 9
PORT ROTATION
VALVE 10
FROM HYDRAULIC ii 24
PUMP 19
4-43
0287G 3/88
SLOW FEED CIRCUIT
REF. NO.
NO.
1 2258-0211 * VALVE ASY, HYDRAULIC (HI-PRESSURE) 1

Consisting of:
lA 2259-0060 * VALVE SECTION, INLET (Husco # 5001-A-1) 1
18 2259-0078 * VALVE SECTION, CYLINDER DETENTED 1

(Husco # 5002-DA5)
1C 2259-0077 * VALVE SECTION, CYLINDER (Husco # 5002-DA5) 1
(W/PORT RELIEFS)
Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
1D 2259-0065 * VALVE SECTION, OUTLET (Husco # 5003-A-4) 1
2 9S01-0038 CAPSCREW (3/8 x 1-1/4) 4

3 9W03-0006 LOCKWASHER (3/8) 4
4 9N01-0009 NUT (3/8) 4
5 2916-0110 LEVER, STR 1
6 3346-0013 PLUG (5/8M0) 2
7 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 2
8 3854-0001 CONNECTOR (1/2FP x 1/2F37) 1
9 3337-0011 NIPPLE, CLOSE X-HVY DS (1/2P) 1
10 2764-0054 VALVE, HYD RELIEF 1
11 3852-0003 TEE (1/2MP x 1/2M37 1/2M37) 1
12 3897-0003 TUBE, REDUCING ST ADPT (1/2 x 3/8) 1
13 3890-0003 NUT, TUBE (37 FLARE) 1
14 3854-0004 CONNECTOR (3/8FP x 3/8F37) 1
15 3337-0008 NIPPLE, CLOSE X-HVY (3/8MP) 1
16 2253-0023 REGULATOR, HYD PRESSURE 1
17 3332-0044 CONNECTOR (3/8M0 x 3/8M37) 1
18 3332-0057 CONNECTOR (1/2M0 x 3/8M37) 1
19 2826-0912 HOSE, HYD 1/2 x 190 100R2 S90 1
20 2826-0540 HOSE, HYD 1/4 x 16 100R1 S90 2
21 3893-0002 ELBOW, 45° (3/8F37 x 3/8M37) 2
22 2826-0389 HOSE, HYD 1/2 x 28 100R2 37S 1
23 2826-0655 HOSE, HYD 3/8 x 36 100R2 S90 1
24 3892-0003 ELBOW, 90° (1/2F37 x 1/2M37) 1
25 5000-8751 VALVE, RELIEF (Husco # 5060) 1


DOWNFEED REGULATOR
4-45
0282G 3/88
DOWNFEED REGULATOR
NO.
REF.
PART NUMBER DESCRIPTION RECt.
NO.
1 2767-0053 VALVE, HYDRAULIC RELIEF (100-1500 PSI) 1

(Fluid Controls # 1A32-R-8T-15-S)
3030-0190 KIT, SERVICE 1A32 REGULATOR
Consisting of:
WASHER, SEALING 2
0-RING .070 x .239 4
2 2429-0044 ANGLE, SUPPORT HYD VALVE 1

3 9501-0028 CAPSCREW (5/16 x 2-3/4) 2
4 9501-0021 CAPSCREW (5/16 x 1) 1
5 9W03-0005 LOCKWASHER (5/16) 3
6 9N01-0008 NUT (5/1 6) 3
7 3883-0016 ELBOW, 90° (1/2MOA x 3/8M37) 2
8 3885-0002 TEE (1/2MOA x 1/2M37 x 1/2M37) 1
9 3897-0001 TUBE, REDUCING ST ADPT 37 (1/2 x 1 /4) 1
10 3890-0003 NUT, TUBE (37 FLARE) 2
11 3897-0003 TUBE, REDUCING ST ADPT 37 (1/2 x 3/8) 1
12 2065-0044 GAUGE, HYD PRESSURE (0-3000) 1
13 3332-0065 CONNECTOR (1/4FP x 1/4M37) 1
14 2826-0895 HOSE, HYD 1/4 x 22 100R1 37S 1
15 2826-0909 HOSE, HYD 3/8 x 48 100R2 S90 1
16 2826-0578 HOSE, HYD 3/8 x 16 100R2 S90 1
17 2826-0655 HOSE, HYD 3/8 x 36 100R2 S90 1

HOLDBACK REGULATOR
TO
°Os,0
Ri o
4 /.. it
es. 7*
.• 0
04.
0
4- 47
0283G 3/88
HOLDBACK REGULATOR
REF. NO.
PART NUMBER DESCRIPTION REO.
NO.
1 2767-0020 VALVE, HYDRAULIC RELIEF (150-3000 PSI) 1

(Fluid Controls # 1A32-R-87-30-S)
3030-0190 KIT, SERVICE 1A32 REGULATOR
Consisting of:
WASHER, SEALING 2
0-RING .070 x .239 4
5000-6057 CARTRIDGE, RELIEF (3000 PSI) 1
(Fluid Controls # 1A30-R-30S)
2 2429-0044 ANGLE, SUPPORT HYD VALVE 1

3 9501-0028 CAPSCREW (5/16 x 2-3/4) 2
4 9S01-0021 CAPSCREW (5/16 x 1) 1
5 9W03-0005 LOCKWASHER (5/16) 3
6 9N01-0008 NUT (5/16) 3
7 3883-0016 ELBOW, 90° (1/2MOA x 3/8M37) 2
8 2764-0009 0-RING (.087 x .644) 1
9 2250-0067 VALVE, CHECK (1 /2 5000 PSI) 1
11 3890-0003 NUT, TUBE (37 FLARE) 1
12 3896-0002 TEE (3/8F37 x 3/8M37 x 3/8M37) 3
14 3890-0002 NUT, TUBE (37 FLARE) 1
15 2065-0045 GAUGE, HYD PRESSURE (0-6000) 1
16 3332-0065 CONNECTOR (1/4FP x 1/4M37) 1
17 2826-0644 HOSE, HYD 1/4 x 18 100R1 37S 1
18 2826-0655 HOSE, HYD 3/8 x 36 100R2 S90 2
19 2826-0578 HOSE, HYD 3/8 x 16 100R2 S90 1
20 2826-0578 HOSE, HYD 3/8 x 16 100R2 S90 1

37
30 22
21 17
31 20
28
71
TO CNIX
ROTATION 70
VALVE
19
TO CMX
ROTATION
VALVE
TO HYD•
TANK
TO SLOW FEED
VALVE
34
TO HYD.
TANK 84,85,86
SdImind01111VHCIAH
83
TO HYD.
TANK 40
46
53
57 75 Et3
7 1:78
58
Et3 76
TO HYD. r/75
TANK 56
TO RAPID
59
FEED VALVE
811
82 60
73 TO RIO
SETOVALVE
0325G 3/88
HYDRAULIC PUMPS
REF. NO.
NO.
1 1040-0025 GEARBOX, TRIPLE PUMP DRIVE 1

(Funk Specification # 10676B)
2 5000-7027 DIPSTICK (Funk # 4028580) 1
3 0877-0521 SUPPORT, FUNK GEARBOX LH 1
4 0925-0008 PLATE, LINE-UP 2
5 0978-0002 CAPSCREW (5/8 x 1-1/2) 8
6 0224-0002 WASHER, HEAD STUD (5/8) 8
8 0570-0032 WASHER, HT (1-5/16 x 1/8 x 25/32) 4
9 0570-0108 WASHER (1-1/2 x 1-1/2 x 49/64) 2
10 9P05-0016 ELBOW, 90° SERVICE (1 /2MP x 1/2FP) 1
11 9P08-0043 NIPPLE (1/2P x 4) 1
12 9P05-0015 ELBOW, 90° (1/2FP x 1 /2FP) 1
14 5000-8306 BREATHER 1
15 5000-1730 COUPLING, PUMP ADAPTOR (SAE C) 2
16 5000-5778 COUPLING, PUMP ADAPTOR (SAE B) 1
17 2764-0109 0-RING (.139 x4.734) 2
18 2764-0030 0-RING (.139 x 3.984) 1
19 2766-0114 PUMP, HYD (Vickers # PVE27R-2-22-C25V-21) 1

5000-9747 KIT, SINGLE SHAFT SEAL (Vickers # 920267)
Consisting of:
0-RINGS 21
SEAL, SHAFT 1
RING, BACKUP 1

21 9W03-0008 LOCKWASHER (1/2) 12
22 0224-0001 WASHER, HEAD STUD (1 /2) 12
23 0995-0047 FLANGE, HYD (2 NPT x 2 PAD) 2
24 2764-0079 0-RING (.139 x 2.234) 2
25 9S03-0016 CAPSCREW, SKT (1/2 x 1-3/4) 8
28 0995-0059 FLANGE, HYD (1 TUBE x 1 PAD) 1
29 2764-0017 0-RING (.139 x 1.234) 1
30 9S03-0029 CAPSCREW, SKT (3/8 x 1-3/4) 4
31 3883-0010 ELBOW, 90° (1MOA x 3/4M37) 1
32 3883-0004 ELBOW, 90° (1/2M0 x 1/2M37) 1
33 3883-0002 ELBOW, 90° (3/8M0 x 1/4M37) 1
34 2766-0091 PUMP, HYD P330 TANDEM (1 x 1/2) 1
(Commercial Shearing # 324-9121-614)
35 3332-0034 CONNECTOR (IMO x 1/2M37) 2
36 3332-0105 CONNECTOR (1-1/2M0 x 1-1/2FP) 1
37 0877-0520 SUPPORT, FUNK GEARBOX RH 1
38 2221-0062 ELBOW, 90° (1-1/2MP x 1-1 /2FPS) 2

0325G 3/88
HYDRAULIC PUMPS
REF. NO.
NO. PART NUMBER OESCR IrnoN
REQ.
39 2766-0116 * PUMP, HYDRAULIC TRIPLE GEAR (Sundstrand Model 1

(# CPA 060 B 030 R C4 A B H/TAP 22/90-38)
Consisting of:
40 2766-0125 * PUMP, HYD (53 GAL) (Sundstrand # CPA-060-RC4ABD) 1
5000-9734 KIT, SEAL (Sundstrand # CP-10064)
Consisting of:
SPACER, SNAP-RING 1
RETAINING, SNAP-RING 1
0-RING, PRESS BAL PLT 8
0-RING, OUTER 1
0-RING, PRESS BAL 4
0-RING, PRESS BAL BACKUP 4
SPACERS 4
0-RING, AUX, "A" PAD 1
0-RING, AUX, "B" PAD 1
SEAL 1
SEAL 1
PLUG, WEEP HOLE 1
0-RING, OUTER CENTER PLATE 2
0-RING, OUTER REAR COVER 1
41 2766-0126 * PUMP, HYD (30 GAL) (Sundstrand # CPB-030-RB2EBA) 1

5000-9735 KIT, SEAL (Sundstrand # CP-10066)
Consisting of:
RETAINER, SNAP-RING 1
0-RING, PRESS BAL PLT 4
0-RING, OUTER 1
0-RING, COVER PLT, OUTER 1
0-RING, PRESS BAL 2
0-RING, PRESS BAL BACKUP 2
SPACERS 2
0-RING, AUX, "A" PAD 1
0-RING, AUX, "B" PAD 1
SEAL 1
SEAL 1
PLUG, WEEP HOLE 1
42 2766-0127 * PUMP, HYD (20 GAL) (Sundstrand # B71922-08800) 1
5000-9736 KIT, SEAL (Sundstrand # 81922-3560K)
Consisting of:
RING, BACKUP 2
0-RING 2
0-RING 2
SEAL, LIP 2
0-RING 2
WASHER, COPPER 4
44 3341-0011 ELBOW, SERVICE DS (1-1/2MP x 1-1/2FP) 1

4-51
0325G 3/88
HYDRAULIC PUMPS
REF. NO.
45 9P08-0144 NIPPLE (1-1/2P x 6)

46 0995-0126 FLANGE (1-1/4 TUBE x 1-1/4 PAD)
47 2764-0036 0-RING (.139 x 1.484)
-Fs
48 9503-0014 CAPSCREW, SKT (7/16 x 1-3/4)
49 3885-0006 TEE (1-1/4MOA x 1M37 x 3/4M37)
50 3854-0003 CONNECTOR (1FP x 1F37)
51 0995-0027 FLANGE, HYD (1-1/4 NPT x 1-1/4 PAD)
N
52 2764-0036 0-RING (.139 x 1.484)
rs.3 N SOO
53 9S03-0014 CAPSCREW, SKT (7/16 x 1-3/4)
54 2221-0045 ELBOW, 90° (1-1/4MP x 1-1 /4FPS)
55 0995-0059 FLANGE, HYD (1 TUBE x 1 PAD)
56 2764-0017 0-RING (.139 x 1.234)
00
57 9503-0029 CAPSCREW, SKT (3/8 x 1-3/4)
58 3883-0010 ELBOW, 90° (1MOA x 3/4M37)
59 3883-0020 ELBOW, 90° (1MOA x 1/2M37)
60 0877-0875 SUPPORT, PUMP
61 9501-0098 CAPSCREW (5/8 x 1-1/2)
62 9W03-0010 LOCKWASHER (5/8)
63 9S01-0099 CAPSCREW (5/8 x 1-3/4)
64 9N06-0005 NUT, JAM (5/8)
68 1313-0103 HOSE, SUCTION (1-1/2 x 17-1/2 NPT)
70 2826-0652 HOSE, HYD 1/4 x 168 100R1 37S
71 2826-0916 HOSE, HYD 3/4 x 185 5000 PSI 37S
72 2826-0581 HOSE, HYD 1/2 x 56 100R2 37S
73 2826-0910 HOSE, HYD 1/2 x 180 100R2 S90
74 2826-0912 HOSE, HYD 1/2 x 190 100R2 S90
75 2826-0917 HOSE, HYD 3/4 x 21 5000 PSI 37S
76 2826-0919 HOSE, HYD 1 x 154 5000 PSI 37S
77 2826-0911 HOSE, HYD 1/2 x 185 100R2 S90
78 3832-0005 ELBOW, 90° (1FP x 1M37)
79 9P05-0034 ELBOW, 90° SERVICE (1-1 /4MP x 1-1/4MP)
80 3337-0038 NIPPLE, REDUCING DS (1-1/2MP x 1-1/4MP)
81 3897-0004 TUBE, REDUCING ST ADPT 37 (1 x 1/2)
82 3890-0006 NUT, TUBE (37 FLARE)
a
83 0374-0021 LOCKNUT (3/4)

SHIM, .030 x 3-1/2 x 7-1 /4 (AS REQUIRED)
1
84 0555-0037
SHIM, .120 x 3-1/2 x 7-1/4 (AS REQUIRED)
.1J 1 1
85 0555-0039
86 0555-0038 SHIM, .060 x 3-1/2 x 7-1/4 (AS REQUIRED)
87 3337-0033 NIPPLE, X-HVY DS (1MP x 3)
88 2221-0075 ELBOW, 90° (1-1/4FP x 1-1/4FPS)
89 2221-0067 ELBOW, 90° (1-1/2FP x 1-1/2FPS)

ALWAYS GIVE EQUIPMENT SERIA L

Printed in U.S.A.
4-52
•
0
0
1
?;•
m
m
0
z
x
m 14
2 ni
00
C
en I
zm
Oz
a-+
▪ ta
>
Z
-I 5
r
0292G 3/88
MAST ASSEMBLY - TOP
(CHAIN, SPROCKETS, ETC.)
REF. PAR T NUMBER NO.

NO. DESCRIPTION REQ.
1 3351-0059 MAST ASV. (33' LONG - 25' TRAVEL) 1

2 1063-0097 SPROCKET, IDLER (WITH BUSHING) 2
3 0860-0020 BUSHING, SPROCKET (2-1/2"OD x 2"ID x 2-1/2" LG) 2
4 0886-0019 SEAL, OIL (2" x 2-7/8" x 15/32") 4
5 1076-0001 PLATEWASHER (3-1/2 x 1/8 x 2-1/64) 4
6 0509-0008 SHAFT, IDLER SPROCKET 2
7 2208-0001 FITTING, GREASE (1/8P) 2
8 9S02-0046 CAPSCREW (1/2NF x 3-1/2) 4
9 0374-0005 LOCKNUT (1/2 NF) 4
10 0509-0053 SHAFT, SPROCKET TIMING (TOP OF MAST) 1
11 2518-0008 BLOCK, PILLOW ROLLER BEARING 2
12 5000-8004 KIT, BEARING REPLACEMENT (Rexnord # 2300U) 2
13 5000-8005 KIT, SEAL REPLACEMENT (Rexnord # MS-9) 2
14 2813-0197 CYLINDER, HYD (4-1/2 x 2-1/2 x 165) 1
15 2813-0197 CYLINDER, HYD (4-1/2 x 2-1/2 x 165) 1
16 2911-0102 SUPPORT, HYD CYLINDER 2
17 0555-0016 SHIN HYD CYLINDER (USE AS NEEDED) 8
18 9W03-0010 LOCKWASHER (5/8) ,4
19 9S01-0100 CAPSCREW (5/8 x 2) 4
20 1063-0096 SPROCKET, IDLER (WITH BUSHING) 4
21 0860-0022 BUSHING, SPROCKET (2-1/2"OD x 2"ID x 3" LG) 4
22 0509-0017 SHAFT, IDLER SPROCKET 4
23 9S02-0046 CAPSCREW (1/2NF x 3-1/2) 4
24 0374-0005 LOCKNUT (1/2 NF) 4
25 2208-0001 FITTING, GREASE (1/8P) 4
26 1076-0007 WASHER, THRUST 8
27 0465-0024 GUIDE, SPROCKET BLOCK (INNER) 2
28 0465-0025 GUIDE, SPROCKET BLOCK (OUTER) 2
29 3390-0016 BLOCK, SPROCKET (NO SPROCKETS) 2
30 3083-0018 PIN, SPROCKET BLOCK (1-1/4 x 6) 2
31 9C01-0024 PIN, COTTER PLT (1/4 x 2) 4
32 3356-0003 SCREW, CHAIN TENSION ADJUST (TOP CHAIN) 2
33 0860-0021 BUSHING, PIN 2
34 3356-0001 SCREW, CHAIN TENSION ADJUST (BOTTOM CHAIN) 2
35 9W02-0012 PLATEWASHER (1-1/4 SAE) 4
36 9NO2-0012 NUT (1-1/4 NF) 4
37 9N07-0011 NUT, JAM (1-1/4 NF) 4
38 2516-0090 CHAIN, ROLLER (253 LINKS) UPPER - PULL UP 2

2516-0098 ROLLER LINK UNIT (ANSI 160 STD)
2516-0097 PIN LINK UNIT (ANSI 160 STD)
39 2516-0088 CHAIN, ROLLER (301 LINKS) LOWER - PULL DOWN 2

2516-0073 ROLLER LINK UNIT (ANSI 140 STD)
2516-0029 PIN LINK UNIT (ANSI 140 STD)
40 3541-0005 BLOCK, LOCK 4

41 0710-0025 CONNECTOR ASV. 2
42 9N06-0008 NUT, JAM (2) 4

rinted in U.S.A. 5-2
0292G 3/88
MAST ASSEMBLY - TOP
(CHAIN, SPROCKETS, ETC.)
REF. NO.
43 3356-0020 SCREW, ADJUSTABLE CHAIN COUPLER 2

44 0822-0225 SPACER, TRUNNION 2
45 0860-0021 BUSHING, PIN 2
46 9S01-0019 CAPSCREW (5/16 x 3/4) 8
47 9W03-0005 LOCKWASHER (5/16) 8
48 3376-0010 PLATE, ROLLER GUIDE 4
49 0177-0001 ROLLER, CAM YOKE (3/8" I.D. x 1-3/8" OD) 8
50 0978-0232 CAPSCREW, ROLLER GUIDE 8
51 0374-0032 LOCKNUT (5/16) 8
52 0555-0015 SHIM, ROLLER GUIDE PLATE (.048) (USE AS NEEDED) 2
53 0978-0068 CAPSCREW (1/2NF x 2-1/4 - SAE GRADE 5) 12
54 9W03-0008 LOCKWASHER (1/2) 12
55 3394-0013 TRUNNION, HALF (WITH BUSHING) 2
56 0860-0079 BUSHING, TRUNNION HALF (2-1/8" ID) 2
58 9W03-0011 LOCKWASHER (3/4) 16
59 0877-0204 SUPPORT, CABLE SHEAVE 1
60 9S01-0074 CAPSCREW (1/2 x 2) 4
61 0374-0016 LOCKNUT (1/2) 4
62 3319-0001 SHEAVE, WIRE ROPE (WHEEL 8" OD x 1" ID) 2
63 3083-0001 PIN, SHEAVE (1 x 3-9/16) 2
64 9S01-0043 CAPSCREW (3/8 x 2-1/2) 2
65 0374-0033 LOCKNUT (3/8) 2
66 0127-0019 EYE, BOLT (1/2) 1
67 9W01-0007 PLATEWASHER (1/2) 1
68 9W03-0008 LOCKWASHER (1/2) 1
69 2208-0001 FITTING, GREASE (1/8P) 2
70 0480-0093 COVER, CABLE SHEAVE 1
71 2029-0001 SCREW, TAPTITE (3/8 x 3/4) 3
72 9N01-0011 NUT (1/2) 1
73 3193-0059 CRADLE, MAST 1
74 2825-0021 PIN, CYLINDER (2 x 7) 2
75 9S01-0072 CAPSCREW (1/2 x 1-1/2) 12
76 9W03-0008 LOCKWASHER (1/2") 12
78 9W03-0011 LOCKWASHER (3/4) 4
79 9W01-0009 PLATEWASHER (3/4) 4
80 0860-0071 BUSHING, PIN 4
81 1063-0065 SPROCKET, IDLE 2
82 9W03-0008 LOCKWASHER (1/2) 4
83 9S01-0072 CAPSCREW (1/2 x 1-1/2) 4
84 2240-0008 CUSHION ASY, GEARBOX 2

Consisting of:
85 2240-0007 CUSHION 2
87 9W08-0001 PLATEWASHER (3/8) 2
88 0374-0033 LOCKNUT (3/8) 2

5-3
•
•
MAST ASSEMBLY - BOTTOM
5-4
0290G 3/88
REF. NO.
REQ.
1 3351-0059 MAST ASY 1

2 2574-0021 HOUSING ASY, MAST PIVOT BRG 2
3 0860-0103 BUSHING (3 ID x 3 LG DXR) 2
4 0886-0114 SEAL, PIPE (14 OD x 4-1/2 ID) 1
5 0978-0291 CAPSCREW (3/4NF x 10 - SAE GRADE 8) 8
6 0570-0032 WASHER, HT (1-5/16 x 1/8 x 25/32) 16
7 0374-0020 LOCKNUT (3/4 NF) 4
8 3374-0020 PLATE, MAST ANCHOR 1
9 0914-0029 PIN, MAST ANCHOR 2
10 3269-0020 BRACKET, HYD CYLINDER SUPPORT 1
11 9S01-0100 CAPSCREW (5/8 x 2) 4
12 9W03-0010 LOCKWASHER (5/8) 4
13 9N01-0013 NUT (5/8) 4
14 2911-0012 SUPPORT, HYD CYL 1
15 2813-0011 CYLINDER, HYD (3 x 1.5 x 8) 1
16 2825-0014 PIN (1 x 6-1/2) 1
17 9W02-0010 PLATEWASHER (1 SAE) 2
18 9C01-0020 PIN, COTTER PLT (3/16 x 1-1/2) 2
19 1018-0019 BOLT, U (5/16 x 3-7/8) 1
20 9W03-0005 LOCKWASHER (5/16) 2
21 9NO2-0002 NUT (5/16 NF) 2
22 1204-0014 GUARD, CHAIN MAST LH 1
23 1204-0015 GUARD, CHAIN MAST RH 1
24 2029-0001 SCREW, TAPTITE (3/8 x 3/4) 6
25 3107-0041 ROD, CHAIN GUARD (1/2 x 8-7/8) (NOT SHOWN) 2
26 9NO2-0005 NUT (1/2 NF) (NOT SHOWN) 2
27 9N07-0006 NUT, JAM (1/2 NF) (NOT SHOWN) 4
28 3389-0028 DEFLECTOR, PIPE UPPER 1
29 3389-0040 DEFLECTOR, PIPE LOWER 1
30 0877-0604 SUPPORT, PIPE DEFLECTOR 9
31 9S01-0070 CAPSCREW (1/2 x 1) 17
32 9W03-0008 LOCKWASHER (1/2) 17
33 9S01-0043 CAPSCREW (3/8 x 2-1/2) 1
35 9W03-0006 LOCKWASHER (3/8) 1
36 9N01-0009 NUT (3/8) 1
37 2551-0089 SUPPORT, HOSE 4
38 2825-0013 PIN (1 x 4-1/2) 1
39 9S01-0027 CAPSCREW (5/16 x 2-1/2) 1
40 0374-0032 LOCKNUT (5/16) 1
41 2264-0013 WRENCH, PIPE BREAKOUT (60 IN.) 1
42 N.S.S. * BOX, SLIP (HALF)
43 0914-0163 PIN, SWING SLIP BOX 2
44 0978-0260 CAPSCREW (1 x 8-1/2 - SAE GRADE 8) 2
45 3753-0001 WASHER, SPRING 8
46 0570-0047 WASHER, HT (2 x 9/64 x 1-1/16) 4
47 0374-0042 LOCKNUT (1) 2
48 3359-0074 SLIP, MASTER 1
49 3366-0013 SLIP, ADAPTOR 1
50 3359-0075 SLIP, GUIDE SET (4-1/2 OD PIPE) 1
51 3360-0010 HANDLE, GUIDE SLIP 2

Printed in U.S.A.
5-5
0290G 3/88
•
REF. NO.

53 9W03-0011 LOCKWASHER (3/4) 4
54 3361-0002 SLIP, HOLDING (4-1/2) 1
55 3420-0003 FRAME, ADAPTOR 1
56 9S01-0102 CAPSCREW (5/8 x 2-1/2) 4
57 9W03-0010 LOCKWASHER (5/8) 10
58 9W01-0008 PLATEWASHER (5/8) 4
59 9501-0098 CAPSCREW (5/8 x 1-1/2) 4
60 9N01-0013 NUT (5/8) 4
61 3389-0047 DEFLECTOR, CHIP 1
62 2750-0030 CURTAIN, CHIP DEFLECTOR (REAR) 1
63 0877-0273 CURTAIN, SUPPORT 1
64 9501-0007 CAPSCREW (1/4 x 1) 35
65 9W01-0003 PLATEWASHER (1/4) 35
66 9W03-0004 LOCKWASHER (1/4) 39
67 91'101-0007 NUT (1/4) 39
68 2750-0036 CURTAIN, CHIP DEFLECTOR (SIDE) 2
69 2750-0061 CURTAIN, CHIP DEFLECTOR (FRONT) 1
70 0877-0870 CURTAIN, SUPPORT 1
2
•
71 0914-0135 PIN, COTTERLESS
72 0930-0028 HOLDER, PIPE SEAL 1
73 9501-0037 CAPSCREW (3/8 x 1) 4
* = Not Sold Separately
SCH RAMM, INC., West Chester, PA • ALWAYS GIVE EQUIPMENT SERIAL

Printed In U.S.A. NUMBER WHEN ORDERING PARTS.
5-6
3/88
0268G
ROTATION GEARBOX ASSEMBLY
• REF.
NO.
64
65
66
PART NUMBER
2208-0001
0978-0269
3357-0128
DESCRIPTION
FITTING, GREASE (1/8P)

CAPSCREW (5/8NF x 1-3/4 - SAE GRADE 8)
SUB, DRIVESHAFT (3-1/2 API PIN)
NO.
REQ.
1
10
1
67 3357-0009 SUB, SAVER (3-1/2 API x 4-1/2 0.0.) 1
0870-0102 * = GEARBOX ASY WITH HYDRAULIC MOTORS
** = See Operator's/Maintenance Manual


Printed in U.S.A.
5-10
PIPE WRENCH
1
•
5-11
0260G 3/88
PIPE WRENCH
REF. NO.
Rte. PART NUMBER DESCRIPTION REQ.
1 2264-0013 WRENCH ASY, PIPE (60 IN.) 1

Consisting of:
2 2263-0008 SPRING, SET (COIL AND FLAT SPRINGS) 1
3 2263-0007 JAW 1
4 2263-0005 JAW, HOOK 1
5 2263-0004 NUT, ADJUSTING 1
6 2263-0006 PIN, SET 1

Printed in U.S.A.
5-12
PIPE HANDLING SLING
5-13
0263G 3/88
PIPE HANDLING SLING
REF. NO.
NO.
1 3323-0004 SLING ASY (FOR 4-1/2" 0.D. PIPE) 1

Consisting of:
2 3482-0030 TONG ASY (FOR 4-1/2" 0.D. PIPE) 1
3 3530-0003 SHACKLE, ANCHOR (1/2") 2
4 3317-0005 CABLE ASY (125° APPROX.) 1
5 2789-0002 HOOK, DRILL PIPE 1
6 3530-0001 SHACKLE, ANCHOR (5/8") 1

Tinted in U.S.A.
5-14
•
•
BREAKOUT CYLINDER
SWING CYLINDER (OPT. JIB BOOM)
6-1
J/ 00
BREAKOUT CYLINDER
SWING CYLINDER (OPTIONAL JIB BOOM)
NO.
REF. DESCRIPTION
NO. PART NUMBER REQ
2813-0011 CYLINDER, HYDRAULIC ASY (3 x 1.5 x 8)
3030-0043 KIT, CYLINDER REPAIR

Consisting of:
-a -a PO -a NONOro N.1
1 - WIPER
2 - 0-RING (.139 x 1.484)
3 - 0-RING
4 - PACKING, ROD
5 - 0-RING (.139 x .734)
6 - PACKING, HYD
7 5000-1925 GLAND, PACKING

8 5000-5227 PISTON
NOTE: Barrel and Rod Not sold separately.

Order Hydraulic Cylinder Asy.

Printed in U S.A.
6-2
FEED CYLINDER
6-3
3/88
0340G
FEED CYLINDER
NO.
REF. DESCRIPTION
PART NUMBER RECL
NO.
2813-0197 CYLINDER, HYDRAULIC ASY (4-1/2 x 2-1/2 x 165)

Consisting of:
1 SEAL, PISTON 1
2 - BAND, WEAR 2
3 - 0-RING (.139 x 1.234) 1
4 - 0-RING 1
5 - WASHER, BACKUP 1
6 - PACKING 1
7 - WIPER 1
8 5000-9580 ROD, PISTON 1

9 5000-9582 GLAND, PACKING 1
10 5000-9581 PISTON 1
NOTE: Barrel not sold separately. Order

Hydraulic Cylinder Asy.

Printed in U.S.A.
6-4
OUTRIGGER CYLINDER
6-5
0341G 3/88
OUTRIGGER CYLINDER
REF. NO.
NO.
2813-0201 CYLINDER, HYDRAULIC ASY (4 x 2 x 41)

Consisting of:
1 - RING, SCRAPER 1
2 - 0-RING (.139 x 1.984) 1
3 - LOCKNUT (1-1 /2 NF) 1
4 - RING, BACKUP 1
5 - 0-RING (.210 x 3.600) 1
6 - 0-RING (.139 x 1.234) 2
7 - PACKING, HYD (4 x .375 x .25) 1
8 - SEAL, PISTON (no o-ring) 1
9 - SEAL, U CUP ROD 1

11 5000-9129 PISTON 1
12 2175-0001 CONNECTOR (1/4MP x 3/8T Flareless) 1
13 2178-0002 ELBOW, 90° (1/4MP x 3/8T Flareless) 1
NOTE: #11 & #12 include Tubing Nut & Ferrule
- TUBING, HYD (3/8 x 54-5/8") 1
14
NOTE: Barrel and Rod not sold separately

ALW
MAST TILT CYLINDER
7
8
6
5
4
9
2
6-7
0342G 3/88
MAST TILT CYLINDER
REF. NO.
2813-0198 CYLINDER, HYDRAULIC ASY (5 x 2-1/2 x 37 Cush)

Consisting of:
1 - RING, PISTON 2
2 - SEAL, PISTON 1
3 - 0-RING (.139 x 1.234) 1
4 - 0-RING (.275 x 4.475) 1
5 - RING, BACKUP 1
6 - PACKING 1
7 - WIPER 1

9 5000-6123 PISTON 1
10 5000-9152 ROD 1
NOTE: Barrel not sold separately. Order

Hydraulic Cylinder Asy.

Printed in U.S.A.
6-8
LAZY SUSAN SWING CYLINDER
6-9
0339G 3/88
LAZY SUSAN SWING CYLINDER
NO.
REF. DESCRIPTION REQ
NO. PART NUMBER
2813-0109 CYLINDER, HYDRAULIC ASY (4 x 1.5 x 7)

Consisting of:
1 - WIPER, ROD 1
2 - SEAL, GLAND 1
3 - 0-RING 1
4 - RING, BACKUP 1
5 - 0-RING (.139 x .734) 1
6 - PACKING, HYD (4 x .375 x .25) 2

8 5000-5390 PISTON 1
NOTE: Barrel and Rod not sold separately.


Printed in U.S.A.
6-10
LAZY SUSAN LOCK PIN CYLINDER
6-11
0344G 3/88
LAZY SUSAN LOCK PIN CYLINDER
NO.
NO. REO
2813-0185 CYLINDER HYDRAULIC ASY

Consisting of:
1 WIPER, SCRAPER (1-3/8 x 1-7/8) 1

2 - SEAL, HYD ROD (1-1/2 ID) 1
2 - SEAL, HYD ROD/PISTON (1-1/2) 1
2 - SEAL, ROD (1-1/4 x 1-1/2 x 1/4) 1
3 - SEAL, HYD CYL ROD/PISTON (2 OD) 1
4 - 0-RING (.139 x 2.234) 1
NOTE: Match Ref. No. (2) with type of seal

in cylinder being repaired

JIB BOOM EXTENSION CYLINDER
(WITH LAZY SUSAN)
6-13
0346G
(WITH LAZY SUSAN)
REF. NO.
2813-0107 CYLINDER, HYDRAULIC ASY (2.5 x 1.25 x 27)

Consisting of:
1 - WIPER 1
2 - SEAL, U CUP 1
3 - 0-RING 1
4 - 0-RING (.139 x .734) 1
5 - SEAL, U CUP 2

7 5000-5225 PISTON 1
8 2178-0002 * ELBOW, 90° (1/4MP x 3/8T Flareless) 1
9 2175-0001 * CONNECTOR (1/4MP x 3/8T Flareless) 1
Note #8 & #9 include Tubing Nut & Ferrule
10 - TUBING, HYD (3/8 x 27") 1
* = Not shown

Order Hydraulic Cylinder Asy
SCH RAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

Printed in U.S.A.
6-14
(WITHOUT LAZY SUSAN)
6-15
034% 3/88
(WITHOUT LAZY SUSAN)
REF. NO.
NO.
REQ.
2813-0097 CYLINDER, HYDRAULIC ASY (2.5 x 1.25 x 21)

Consisting of:
1 - WIPER 1
2 - SEAL, U CUP 1
3 - 0-RING 1
4 - 0-RING (.139 x .734) 1
5 - SEAL, U CUP 2

7 5000-5225 PISTON 1
8 2178-0002 * ELBOW, 90° (1/4MP x 3/8T Flareless) 1
9 2175-0001 * CONNECTOR (1/4MP x 3/8T Flareless) 1
Note #8 & #9 include Tubing Nut & Ferrule)
10 - TUBING, HYD (3/8 x 21") 1
* = Not shown


Printed in U.S.A.
6-16
PRESSURE LUBRICATOR
4
8
L-
22
27
19
14 6B
11
12
L ins 10
:*'%‘ ".••••.. dia 37
I 21 15
t,_ I _)
•••••• I 294 18
17
_2„dr___ 28
6-17
0278G 3/88
PRESSURE LUBRICATOR
REF. NO.
NO.
2117-0005 LUBRICATOR ASY

(Items not included Ref. #'s 19, 22, 28)
1 3666-0001 CAP, PRESSURE LUBRICATOR 1

2 3674-0001 BODY, METERING VALVE 1
3 0255-0001 VALVE, PRESSURE LUB METERING 1
4 0585-0002 DISC, PILOT VALVE 1
5 3662-0004 BODY, PRESSURE LUBRICATOR 1
6 3663-0003 PLUNGER ASY, PRESSURE LUBRICATOR 1

Consisting of:
6A 3663-0001 * PLUNGER, PRESSURE LUBRICATOR 1

6B 3664-0002 * CYLINDER, LUBRICATOR 1
7 3668-0001 SPRING 1
8 3667-0001 SEAT, PRESSURE LUBRICATOR DISC 1
-awe-
9 3669-0003 BODY ASY, LUBRICATOR VALVE 1
Consisting of:
10 3669-0002 BODY, LUBRICATOR VALVE 1

11 3681-0001 SPRING, PRESSURE LUBRICATOR VALVE 2
12 3680-0001 DISC, PRESSURE LUBRICATOR VALVE 2
13 3679-0001 BUMPER, LUBRICATOR VALVE 1
14 3679-0002 BUMPER, LUBRICATOR VALVE 1
15 3670-0002 CAP, PRESSURE LUBRICATOR VALVE BODY 1

16 3672-0001 HEAD, LUBRICATOR FILTER 1
17 2296-0001 FILTER, ELEMENT 1
18 0326-0001 SCREW, ADJUSTING 1
19 3676-0001 GASKET, LUBRICATOR VALVE BODY 1
20 0999-0005 BALL, STEEL 2
21 2298-0001 BREATHER, CRANKCASE 1
22 0598-0033 GAUGE, OIL LEVEL AND CAP 1
23 0740-0002 CUP, OIL FILLER 1
24 2764-0018 0-RING 1
25 2764-0005 0-RING 1
26 2764-0007 0-RING 1
27 2764-0008 0-RING 1
28 2912-0020 CASE, PRESSURE LUBRICATOR 1
29 9S03-0006 SCREW, CAP SOCKET (1/4 x 1) 7
30 9S03-0005 SCREW, CAP SOCKET (1/4 x 3/4) 6
31 9N07-0002 NUT, JAM (1/4 NF) 1
32 3682-0001 GASKET, METERING VALVE 1
33 9S01-0035 CAPSCREW (5/16 x 1-1/4) 3
* = Available only as a matched set.

Printed in U.S.A.
6-18
ROTATION GEARBOX DIRECTIONAL CONTROL VALVE
6-19
0259G 3/88
ROTATION GEARBOX DIRECTIONAL CONTROL VALVE
REF. NO.
PART NUMBER DESCRIPTION RE Q
NO.
1 2258-0215 VALVE ASY, ROTATION DIRECTION CONTROL 1

Consisting of:
lA 2258-0214 BODY, VALVE 1
18 2258-0175 * CARTRIDGE, DIRECTIONAL CONTROL VALVE 2

5000-8842 KIT, CARTRIDGE REPAIR
Consisting of:
- 0-RING. (.116 x 1.171) 1

- 0-RING (.070 x 1.114) 1
- 0-RING (.210 x .662) 1
- 0-RING (.103 x .799) 1
- WASHER, BACKUP 2
- WASHER, BACKUP 2
- WASHER, BACKUP 2
2 3346-0012 PLUG (1/2M0) 1


rinted in U.S.A.
6-20
MINIMUM PRESSURE VALVE
6-21
0303G 3/88
MINIMUM PRESSURE VALVE
REF. NO.
3997-0011 VALVE, MINIMUM PRESSURE (150 PSI)

3030-0219 KIT, MINIMUM PRESSURE VALVE REPAIR
Consisting of:
1 - RING, RETAINING 1
2 - RING, TEFLON SEAL 1
3 - PISTON, CHECK 1
4 - WASHER, SEALING 1
5 - WASHER, RETAINING 1
6 - BUTTON HEAD SCREW (5/16 x 3/4 - SAE GRADE 8) 1
7 - 0-RING (.118 x 2.337) 2
8 - SEAT 1

Printed in U.S.A.
6-22
•
i
S
JIB BOOM - TOP OF MAST
(STANDARD - SINGLE LINE PULLEY)
7-1
UCYLI.Li
3/88
JIB BOOM - TOP OF MAST
(STANDARD - SINGLE LINE PULLEY)
REF.
NO. PARTNUMBER DESCRIPTION NO.
REQ.
1 3193-0023 BASE, JIB BOOM

2 1
3 9W02-0007 PLATEWASHER (5/8 SAE)
4 12
0374-0019 LOCKNUT (5/8) 16
5 2208-0001 FITTING, GREASE (1/8P)
6 4
7 2333-0002 BEARING, CAMROL (2" DIA.) 1
8 9NO2-0009 NUT (7/8 NF) 1
9 9W03-0012 LOCKWASHER (7/8) 1
10 0374-0021 LOCKNUT (3/4) 1
11 0570-0020 PLATEWASHER (2 x 1/4 x 13/16) 2
12 0374-0044 LOCKNUT (3/4) ALTERED 1
13 0570-0060 WASHER, SPACER (2-1 /2 x 1/8 x 1-5/8) 1
14 3416-0004 PIN (1 x 5) 1
15 9S01-0012 CAPSCREW (1/4 x 2-1 /2) 2
16 0374-0003 LOCKNUT (1 /4) 4
17 3416-0002 PIN (1 x 7-7/16) 1
18 9W02-0010 PLATEWASHER (1 SAE) 3
19 9C01-0017 PIN, COTTER PLT (5/32 x 1-1/2)
20 3
3319-000,g SHEAVE, WIRE ROPE (WHEEL 8" O.D. x 1" I.D.) 2
21 3083-0004 PIN, SHEAVE (1 x 6-7/8)
22 1
3083-0005 PIN, SHEAVE (1 x 5-1 /8) 1
23 9S01-0013 CAPSCREW (1/4 x 2-3/4) 2
24 2813-0011 CYLINDER, HYDRAULIC (SWING) (3 x 1.5 x 8) 1
25 3416-0005 PIN (1 x 3-7/8) 1
27 0860-0040 BUSHING, SHEAVE WHEEL (1-3/8 x 1 x 1-3/8) 2
28 0465-0035 GUIDE, WIRE ROPE 1
29 2029-0001 SCREW, TAPTITE (3/8 x 3/4) 4
30 0860-0013 BUSHING, PIVOT PIN (1-25/32 x 1-5/8 x 1 DU) 2
31 0465-0008 GUIDE, TUBE 8
32 3169-0081 * TUBE, OUTER 1
33 3169-0082 * TUBE, INNER 1
34 2813-0107 * CYLINDER, HYDRAULIC (2.5 x 1.25 x 27) 1
35 3169-0077 ** TUBE, OUTER 1
36 3169-0078 ** TUBE, INNER 1
37 2813-0097 ** CYLINDER, HYDRAULIC (2.5 x 1.25 x 21) 1
* = Units WITH Lazy Susan

** = Units WITHOUT Lazy Susan

7-2
LAZY SUSAN ASSEMBLY
43 67
49
68
s
32 75
AA * 48
32
30
)69
22
62
28
31
29
7 24 INCLUDES
30, 31,32
17
55
36
56
21
35
2
33
79
34
.1177
78
so
80
70C 23
76 73
22 71 72
7
7-3
0291G
3/88
LAZY SUSAN ASSEMBLY
REF.
PART NUMBER NO.
NO. DESCRIPTION
REQ.
1 3238-0061 SUPPORT, PIPE HOLDER (LOWER)

2 1
0978-0035 CAPSCREW (5/8 x 2 - SAE GRADE 5)
3 10
0374-0019 LOCKNUT (5/8)
4 10
2329-0001 BEARING, OUTER RACE 1
5 2329-0002 BEARING, INNER RACE
6 0886-0081 1
SEAL, OIL (2-3/4 x 3-3/4 x 1/2) 1
7 2208-0001 FITTING, GREASE (1/8P)
8 6
1951-0192 SUPPORT, PIPE HOLDER (UPPER) WELD TO MAST
9 1
3238-0060 SUPPORT, PIPE HOLDER (UPPER)
10 1
0978-0023 CAPSCREW (1/2 x 5-1/2 - SAE GRADE 5)
11 3238-0063 1
SUPPORT, PIPE HOLDER (INCLUDES BUSHINGS) 1
12 0914-0084 PIN, PIPE HOLDER (2-3/4 x 6-1/8)
13 1
3624-0003 BUSHING, SELF-ALIGNING (3-3/16 x 2)
14 1
0886-0038 SEAL, OIL (2-1/4 x 3-1/4 x 1 /2)
15 1
0914-0083 PIN, PIPE HOLDER (2-1/4 x 8-5/8)
16 1
0374-0019 LOCKNUT (5/8)
17 6
9501-0100 CAPSCREW (5/8 x 2)
18 6
2813-0109 CYLINDER, HYDRAULIC (SWING) (4 x 1.5 x 7)
19 1
0914-0085 PIN, HYD CYL SUPPORT (1 x 5-11/16) BASE 1
20 0914-0086 PIN, HYD CYL SUPPORT (1 x 4-11/16) RAM END #1(5-3(4 1
21 2442-0010 PIN, ROLL (3/16 x 1-5/8)
22 4
9S01-0131 CAPSCREW (1 x 2-3/4) (SWING STOP) 2
23 9N06-0007 NUT, JAM (1) 2
24 3244-0047 HOLDER, SEVEN PIPE 1
25 9S01-0071 CAPSCREW (1/2 x 1-1/4) 8
26 9W03-0008 LOCKWASHER (1/2) i 8
27 3249-0100 PLATE, PIPE HOLDER (4-1/2 PIPE) 1
28 9S01-0102 CAPSCREW (5/8 x 2-1/2) 6
29 0374-0019 LOCKNUT (5/8) 6
30 1060-0026 SHAFT AND SPROCKET ASY 1
31 0914-0112 PIN, TAPER THREADED (8 x 4-3/4)
32 1
0374-0016 LOCKNUT (1 /2) 2
33 0077-0061 PIN, DOWEL (1-1/4 x 2-1/2) 14
34 3249-0098 PLATE, LOCK PIN (WELD TO PIPE HOLDER) 1
35 0094-0014 SOCKET, DRILL PIPE (4-1/2)
36 7
37 9W03-0010 LOCKWASHER (5/8)
38 7
0070-0010 BEARING, THRUST (3" BORE, 4" OD) 1
39 0978-0023 CAPSCREW (1/2 x 5-1 /2 - SAE GRADE 8) 1
40 0374-0016 LOCKNUT (1/2) 1

Printed In U.S.A. NUMBER WHEN ORDERING PARTS
7-4
3/88
0291G
LAZY SUSAN ASSEMBLY
REF. DESCRIPTION RED.

PART NUMBER
NO.
MOTOR, HYDRAULIC (Char-Lynn # 101-1040) 1

41 2999-0035 *
(Char-Lynn "H" SERIES 23.8 CU. IN.)
5000-8224 MOTOR SEAL KIT (Char-Lynn # 60023)
Consisting of:
SEAL, DUST 1
SEAL, SHAFT PRESSURE 1
SEAL 1
SEAL 3
WASHER, SEAL 7
SEAL, 0-RING 2
0-RING 1
SPACER, HYD MOTOR (SAE A, 2-BOLT) 1

42 0822-0171
CAPSCREW (1 /2 x 1-3/4) 2
43 9S01-0073
LOCKNUT (1 /2) 2
44 0374-0016
45 9W02-0006
SETSCREW, ALLEN, KNURLED, CUP POINT (5/16 x 7/16) 2
46 9535-0004
2516-0044 CHAIN, ROLLER (64 PITCHES) 1
47
GUARD, CHAIN 1
48 1204-0009
SPROCKET, DRIVE 1
49 1063-0030
CYLINDER, LOCK PIN 1
50 2813-0185
CAPSCREW (1/2 x 1-1 /2 - SAE GRADE 5) 4
51 0978-0085
LOCKWASHER (1/2) 4
52 9W03-0008
CAPSCREW (1 x 3-1/2 - SAE GRADE 5) 1
53 0978-0199
NUT, JAM (1) 1
54 9N06-0007
GUIDE, SEVEN PIPE (4-1 /2" OD) (2 PIECES) 1
55 0465-0063
PLATE, GUIDE (4-1/2 PIPE) 7
56 3376-0025
BLOCK, GEARBOX STOP 1
57 2873-0019
CAPSCREW (3/4 x 4 - SAE GRADE 5) 4
58 0978-0034
9W03-0011 LOCKWASHER (3/4) 4
59
9S02-0047 CAPSCREW (1/2NF x 3-3/4) 3
60
9W03-0008 LOCKWASHER (1/2) 3
61
3249-0094 PLATE, PIPE STOP 1
62 2
63 3238-0025 SUPPORT, PIPE HOLDER (WELD TO MAST)
64
9W03-0010 LOCKWASHER (5/8) 6
65
66 2208-0001 FITTING, GREASE (1/8P) 2
67 9501-0037 CAPSCREW (3/8 x 1) 2
68 9W03-0006 LOCKWASHER (3/8) 2
69 0860-0073 BUSHING (2-7/16 x 2-1/4 x 2) 2
'70 0860-0074 - -4- BUSHING (3-3/16 x 3 x 2) 2
71 2370-0001 SHIELD, HAND 1
72 3441-0002 STRIP, REINFORCING 1
73 2029-0004 SCREW, TAPTITE (5/16 x 3/4) 3
74 9S22-0021 SETSCREW, ALLEN CUP POINT (5/8 x 1-1/2) 1
75 9W01-0005 PLATEWASHER (3/8) 2
76 0914-0111 PIN, LAZY SUSAN (2-63/64 x 9-1/4) 1
77 9S01-0107 CAPSCREW (5/8 x 3-3/4) 4

0291G 3/88
LAZY SUSAN ASSEMBLY
REF.
PART NUMBER NO.
NO. DESCRIPTION
REQ.
78 9W03-0010 LOCKWASHER (5/8) 4

80 2932-0018 POINTER, INDEXING 7 PIPE L.S. 1


7-6
JIB BOOM HYDRAULIC CIRCUIT
FROM WINCH
VALVE
7-7
0295G 3/88
JIB BOOM HYDRAULIC CIRCUIT
REF. NO.
REQ.
1 2813-0011 CYLINDER ASY, HYD (3 x 1.5 x 8) 1

2 3332-0026 CONNECTOR (1/4MP x 1/4M37) 1
3 3892-0001 ELBOW, 90° (1/4F37 x 1/4M37) 1
5 2813-0107 CYLINDER ASY, HYD (2.5 x 1.25 x 27) 1
6 3332-0039 CONNECTOR (1/4MP x 1/4M37 .055) 2
7 3337-0006 NIPPLE, DS X-HVY (1/4P x 3) 1
8 3340-0001 ELBOW, 90° DS (1/4FP x 1/4FP) 1
9 3332-0026 CONNECTOR (1/4MP x 1/4M37) 1
10 3345-0001 COUPLING, DS (1/4FP) 1
11 3864-0003 CONNECTOR (1/2M37 x 1/4M37) 8
12 3312-0018 CLAMP ASY (1/2" OD HYD TUBES) 4
13 2021-0022 GROMMET (1/2" OD HYD TUBING) 16
14 3879-0002 TUBING ASY, HYD 37 ST (1 /2 x 240) 4

Consisting of:
15B 2259-0061 * VALVE SECTION, CYLINDER (Husco # 5002-A-1) 3
15C 2259-0063 * VALVE SECTION, MOTOR (Husco # 5002-A-10) 1

Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
POPPET, CHECK LOAD 1
SPRING, CHECK LOAD 1
15D 2259-0065 * VALVE SECTION, OUTLET (Husco # 5003-A-4) 1
16 9S01-0038 CAPSCREW (3/8 x 1-1/4) 4

17 9W03-0006 LOCKWASHER (3/8) 4
18 9N01-0009 NUT (3/8) 4
19 2916-0110 LEVER, ST 4
20 3885-0012 TEE (5/8M0A x 1/2M37 x 1/4M37) 1
21 3889-0001 CAP (1 /4F37) 1
22 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 1
23 3332-0067 CONNECTOR (1/2M0 x 1/4M37) 4
24 3346-0013 PLUG (5/8M0) 2
25 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S 1
26 2826-0482 HOSE, HYD 1/2 x 125 100R2 37S 1
27 2826-0442 HOSE, HYD 1/4 x 150 100R1 37S 4
28 2826-0397 HOSE, HYD 1/4 x 86 100R1 37S 2
29 2826-0415 HOSE, HYD 1/4 x 72 100R1 37S 1
30 2826-0413 HOSE, HYD 1/4 x 60 100R1 37S 1


7-8
LAZY SUSAN HYDRAULIC CIRCUIT
is
LOCK PIN
16 CYLINDER 20
13 --7 19
17
18
35 37
LAZY 20
19
SUSAN
MOTOR 38
TO MAST
TUBING
RETURN
LINE
2
--J26
27 35
26
26 33
4 2110
34
27
SWING
CYLINDER
3 X,
yik it‘ ,tx0
` K‘ G
C) s t•%. ti- ‘0,
-1.-4 5\3 SW
tO00,
1 GO
1.
3\ 4
10
39
FROM WINCH
VALVE
7-9
0293G 3/88
REF.
PART NUMBER NO.
NO. DESCRIPTION
REQ.

Consisting of:
lB 2259-0061 * VALVE SECTION, CYLINDER (Husco # 5002-A-1) 3
1C 2259-0063 * VALVE SECTION, MOTOR (Husco # 5002-A-10) 1
3030-0216 VALVE SECTION REPAIR KIT _
Consisting of:
SEAL, WIPER 2
SEAL, SPOOL 2
0-RING, SECTION 2
POPPET, CHECK LOAD 1
SPRING, CHECK LOAD 1
10 2259-0065 * VALVE SECTION, OUTLET (Husco # 5003-A-4) 1
2 9S01-0038 CAPSCREW (3/8 x 1-1/4) 4
3 9W03-0006 LOCKWASHER (3/8) 4
4 9N01-0009 NUT (3/8) 4
5 2916-0110 LEVER, ST 4
6 3885-0012 TEE (5/8MOA x 1/2M37 x 1/4M37) 1
7 3889-0001 CAP (1/4F37) 1
8 3332-0014 CONNECTOR (5/8M0 x 1/2M37) 1
9 3332-0067 CONNECTOR (1/2M0 x 1 /4M37) 4
10 3346-0013 PLUG (5/8M0) 2
11 2813-0109 CYLINDER, HYD (4 x 1.5 x 7) 1
12 3332-0026 CONNECTOR (1/4MP x 1/4M37) 2
13 2999-0035 * MOTOR, HYDRAULIC (Char-Lynn # 101-1040) 1

(Char-Lynn "H" SERIES 23.8 CU. IN.)
5000-8224 MOTOR, SEAL KIT (Char-Lynn # 60023)
Consisting of:
SEAL, DUST I
SEAL, SHAFT PRESSURE 1
SEAL 1
SEAL 3
WASHER, SEAL 7
SEAL, 0-RING 2
0-RING 1
14 3332-0014 CONNECTOR (5/8M0 x 1 /2M37) 2

15 2764-0010 0-RING (.097 x .755) 2
16 3897-0008 TUBE, REDUCING ST (1/2 x 1/4 .040 RESTRICTED) 2
17 3890-0003 NUT, TUBE (37 FLARE) 2
18 2813-0185 CYLINDER, LAZY SUSAN LOCK PIN 1
19 3332-0011 CONNECTOR (1/4M0 x 1/4M37) 2
20 2764-0105 0-RING (.072 x .351) 2

7-10
3/88
029%
NO.
REF. DESCRIPTION EQ.
NO. PART NUMBER
1
21 2251-0002 VALVE, DUAL SEQUENCE
1
22 0877-0429 SUPPORT, VALVE
2
23 9501-0031 CAPSCREW (5/16 x 3-1/2)
2
24 9W03-0005 LOCKWASHER (5/16)
2
25 9W01-0004 PLATEWASHER (5/16) 5
26 3332-0067 CONNECTOR (5/8M0 x 1/4M37)
6
27 2764-0009 0-RING (.087 x .644)
CONNECTOR (1/2M0 x 1/2FP) 1
28 3332-0032 1
29 2558-0003 BUSHING, REDUCING DS (1/2MP x 1/4FP)
1
30 3337-0003 NIPPLE, DS CLOSE X-HVY (1/4MP)
1
31 2250-0054 VALVE, SHUTTLE (1/4P)
2
32 3332-0026 CONNECTOR (1 /4M0 x 1/4M37)
2
33 2826-0749 HOSE, HYD 1/4 x 235 100R1 S90
2
34 2826-0584 HOSE, HYD 1 /4 x 160 100R1 S90
2
35 2826-0751 HOSE, HYD 1/4 x 246 100R1 37S
1
36 2826-0596 HOSE, HYD 1/4 x 13 100R1 S45
1
37 2826-0942 HOSE, HYD 1/4 x 110 100R1 37S
1
38 2826-0838 HOSE, HYD 1/4 x 166 100R1 S90
1
39 2826-0373 HOSE, HYD 1/2 x 33 100R2 37S
1
40 2826-0482 HOSE, HYD 1/2 x 125 100R2 37S


Printed in U.S.A. 7-IT
•
•
FLOATING SUB ASSEMBLY
..,
7-12
0316G 3/88
FLOATING SUB ASSEMBLY
REF. NO.
NO. PART NUMBER DESCR IPTION
R EO.
3357-0126 SUB ASY, FLOATING (DRIVE SHAFT x 3-1 /2 API) 1

Consisting of:
1 3357-0125 ADAPTOR, FLOATING (SUB TO DRIVE SHAFT) 1
2 3169-0162 TUBE, FLOATING SUB AIR SEAL 1
3 3357-0032 TUBE, FLOATING SUB TORQUE 1
4 0978-0270 CAPSCREW (5/8NF x 2-1/2 - SAE GRADE 8) 10
5 3357-0021 SHAFT, FLOATING SUB 1
6 2764-0021 0-RING. (.210 x 1.850) 1
7 3357-0033 COLLAR, FLOATING SUB (2 HALVES) 1
8 3327-0001 STRIP, WIPER 1
9 9512-0005 CAPSCREW, UNRF SOCKET (5/8 x 1-3/4) 10
10 2209-0001 FITTING, GREASE (1/4P) 1
SCHRAMKINC.,WestCM,ster,PA ALWAYS GIVE EQUIPMENT SERIAL

Printed in U.S.A.
7-13

Schramm T660H Manual

Uploaded by

Copyright:

Available Formats

Schramm T660H Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Schramm T660H Manual

Uploaded by

Copyright:

Available Formats

SCHRAMM LIMITED WARRANTY

CUSTOMER NAME AND ADDRESS TERR. DATE

DATE SHIPPED FROM W.C. HOW LONG IN SERVICE

2 -7 I fa IT f\A VA s-r- I OP et-trei , Ids 269 i‘o w

ROTADRILL T660H PARTS MANUAL

Main Frame Components Chapter 1

Engine, Heat Exchanger And Pump Gearbox Drive Components Chapter 2

Compressor And Air Line Circuit Chapter 3

Control Panel, Hydraulic Circuits And Hydraulic Pumps Chapter 4

Mast And Rotation Gearbox Components Chapter 5

Component Breakdown Chapter 6

Chapter 1 Main Frame Components

Rear Outrigger 1-1

Chapter 2 Engine, Heat Exchanger And Pump Gearbox

Deck Engine Service Components 2-1

Chapter 3 Compressor And Air Line Circuit

Compressor Service Components 3-1

thApter 4 Control Panel, Hydraulic Circuits And

Control Panel - Engine 4-1

ROTADRILL T660H PARTS MANUAL

Chapter 4 Control Panel, Hydraulic Circuits And

Outrigger Circuit 4-9

Chapter 5 Mast And Rotation Gearbox Components

Mast Assembly - Top (Chain, Sprockets, Etc.) 5-1

Chapter 6 Component Breakdown

Breakout Cylinder - Swing Cylinder (Opt. Jib Boom) 6-1

ROTADRILL 1660H PARTS MANUAL

Jib Boom - Top Of Mast (Standard - Single Line Pulley) 7-1

Electrical System Schematic Drawing 0859-0114

Air Valve 3-2

Clutch Control 3-12

Deck Engine Service Components 2-1

Electrical System Schematic Drawing 0859-0114

Feed Cylinder 6-3

Heat Exchanger And Hydraulic Oil Cooler 2-8

Jib Boom - Top Of Mast (Standard - Single Line Pulley) 7-1

Lazy Susan Assembly 7-3

Mast Assembly - Bottom (Dust Diverter Asy, Guide Slips, 5-4

Operator Platform 4-5

Pipe Handling Sling 5-13

Radiator Fan Drive 2-15

Scavenger Line And Control Line Filters 3-16

Tool Box 1-6

Water And Foam Injection Pump Asy. (10 GPM) 4-33

1 2813-0201 CYLINDER, HYD (4 x 2 x 41) 2

SCHRAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

1 3193-0044 SUPPORT, OUTRIGGER & MAST CRADLE 1

ALWAYS GIVE EQUIPMENT SERIAL

0749-0032 BOX, TOOL 1

SCHRAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

1 0159-0012 SUPPORT, BATTERY (WELDED TO DECK) 1

SCHRAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

1 0211-0053 TANK, FUEL (180 GAL) 1

ALWAYS GIVE EQUIPMENT SERIAL

1 0211-0053 TANK, FUEL (180 GAL) 1

SCHRAMM, INC., West Chester, PA ALWAYS GIVE EQUIPMENT SERIAL

ALWAYS GIVE EQUIPMENT SERIAL

ALWAYS GIVE EQUIPMENT SERIAL

ALWAYS GIVE EQUIPMENT SERIAL

0877-0340 SUPPORT, FLYWHEEL HSG 16