Secoroc COP RC45/

COP RC45 HD
Reverse Circulation
Smaller.
Lighter.
Faster.
The Secoroc COP RC45 is a different hammer using the latest
material technology providing the best possible performance
to our customers! When you purchase COP RC45 you buy
the best and most innovative technology on the market. The
COP RC45 hammer will give you both easy handling and
outstanding drilling performance. No compromises.
Great performance High frequency Efficient sampling
in a small package The COP RC45 has a unique air The COP RC45 features Secoroc's
chamber design. Much smaller unique tube retention system. This
The Secoroc COP RC45 reverse
chambers build up pressure faster design makes it easy to service
circulation hammer features a
and makes the piston strike at a much and replace tubes since you don't
revolutionary new design. It's 40%
faster rate. The result is marginally have to disassemble the hammer.
shorter than the nearest competitor.
lower impact energy. But, this is more Quite simply this means minimum
And shorter means less weight.
than compensated for by a much down-time and maximum time
The COP RC45 is more than 30%
higher strike frequency – at 30 bar an producing samples.
lighter than most hammers doing
increase by 30% compared to RC 50.
the same job.
This leads to a great increase in power Lower total cost
output and a sizeable improvement in All in all, COP RC45 offers high
penetration rate. Tests show excellent productivity, a long service life and –
drilling results in all types of rock – most importantly – efficient sampling.
also in difficult rock formations.

Main benefits
• High frequency
– to maximize power output.
• Simple design
– for easy maintenance.
• Light
– for easy handling.
• New hammer cycle
– to improve fuel efficiency.
Technical specifications COP RC45
COP RC45 specifications COP RC45 sleeve assortment
Product No. 89011483 OD OD Chuck Product
sleeve Product Code
Product code 9704-RC-00-66B-91-00 (mm) (inch) Design No.

Outside diameter (mm) 120 124 4.88 RC45 std 89011487 9704-RC-00-000-00-000-C24
Length without bit (mm) 803 126 4.96 RC45 std 89011488 9704-RC-00-000-00-000-C26
Weight without bit (kg) 41 129 5.08 RC45 std 89011489 9704-RC-00-000-00-000-C29
Wrench flat on backhead (mm) 102 132 5.19 RC45 std 89011490 9704-RC-00-000-00-000-C32
Bit size, min-max (mm) 125-140 135 5.31 RC45 std 89011491 9704-RC-00-000-00-000-C35
Recommended bit sizes (mm) 127-136 137 5.39 RC45 std 89011492 9704-RC-00-000-00-000-C37
Bit shank RC 45 139 5.47 RC45 std 89011493 9704-RC-00-000-00-000-C39
Piston weight (kg) 10,4
Backhead thread 4½" Remet Box
Working pressure, (bar (Psi)) 10-35 (145-500)

COP RC45 air consumption COP RC45 shank bit assortment

Air Air Penetration OD OD Product
Impact rate Rec. Design Product Code
pressure cons. rate (mm) (inch) No.
Trubbnos
Values from standardized 125 4.92 90029886 100-5125-91-0489,10-20
gauge
laboratory test in Swedish
granite, 220 MPa, 30 % SiO. Trubbnos
127 5.00 90029774 100-5127-91-0498,10-20
gauge
Strokes/
Bar l/s Hz mm/min Rpm Trubbnos
min 130 5.12 90029887 100-5130-91-0498,10-20
gauge
10 110 2100 35 100 85-95
Trubbnos
15 175 2400 40 200 95-105 133 5.25 90029772 100-5133-91-0491,10-20
gauge
20 250 2820 47 533 110-125 Trubbnos
136 5.39 90029888 100-5136-91-0491,10-20
25 335 3060 51 700 120-135 gauge

30 430 3240 54 933 130-145 Trubbnos

140 5.51 90029773 100-5133-91-0491,10-20
gauge
Performance figures are average values for new hammers at sea level.
Specifications and other data subject to alteration without prior notice. 165 6.49 Collaring bit 90029861 100-5165-91-0412,10-20

If your drill rig can’t reach the RPMs above please contact your local Epiroc
representative for recommendation.

COP RC45 kits, consumables, accessories

Description Product No. Product code
Seal kit 89012400 9704-RC-00-66B-91-000-K47
Check valve kit 89011569 9704-RC-00-000-00-000-K17
Rebuild kit 89012401 9704-RC-00-66B-91-000-K40
Backhead assemby 89012364 9704-RC-00-66B-00-000-A20
Casing 89011482 9704-RC-00-000-00-000-004
Inner tube assembly 89011499 9704-RC-00-000-91-000-R95
Inner tube adapter
89012365 9704-RC-00-66B-00-000-R94
assembly
Grinding wheel, 14 mm 87001025 9500-1025
Grinding wheel 15,8 mm 87005166 95-3-DC-0158-Tru,H
Grinding wheel, 16 mm 87001027 9500-1027
Grinding wheel, 19 mm 87003966 9500-3966
Grinding wheel,
87005167 9500-3966
Trubbnos 19,1 mm
Wrench NV102 89000667 8484-0214-13
Bit holder 87004605 9500-4605
Technical specifications COP RC45 HD
COP RC45 HD specifications COP RC45 HD sleeve assortment
Product No. 89012468 Chuck
OD OD Product
sleeve Product Code
Product code 9704-RC-00-66B-91-H00 (mm) (inch) No.
Design
Outside diameter (mm) 125
RC45
129 5.08 89012463 9704-RC-00-000-00-H00-C29
Length without bit (mm) 803 HD
Weight without bit (kg) 48,5 RC45
132 5,.9 89012464 9704-RC-00-000-00-H00-C32
HD
Wrench flat on backhead (mm) 102
RC45
Bit size, min-max (mm) 127-140 135 5.31 89012465 9704-RC-00-000-00-000-C35
HD
Recommended bit sizes (mm) 130-140 RC45
137 5.39 89012466 9704-RC-00-000-00-H00-C37
Bit shank RC 45 HD

Piston weight (kg) 10,4 RC45

139 5.47 89012467 9704-RC-00-000-00-H00-C39
HD
Backhead thread 4½" Remet Box
RC45
Working pressure, (bar (Psi)) 10-35 (145-500) 164 6,45 89012503 9704-RC-00-000-00-000-C64
HD/STD

COP RC45 HD air consumption COP RC45 HD shank bit assortment

Air Air Penetration OD OD Product
Impact rate Rec. Design Product Code
pressure cons. rate (mm) (inch) No.
Trubbnos
Values from standardized 130 5.12 90029887 100-5130-91-0498,10-20
gauge
laboratory test in Swedish
granite, 220 MPa, 30 % SiO. Trubbnos
133 5.25 90029772 100-5133-91-0491,10-20
gauge
Strokes/
Bar l/s Hz mm/min Rpm Trubbnos
min 136 5.39 90029888 100-5136-91-0491,10-20
gauge
10 110 2100 35 100 85-95
Trubbnos
15 175 2400 40 200 95-105 140 5.51 90029773 100-5133-91-0491,10-20
gauge
20 250 2820 47 533 110-125 165 6.49 Collaring bit 90029861 100-5165-91-0412,10-20
25 335 3060 51 700 120-135
30 430 3240 54 933 130-145

Performance figures are average values for new hammers at sea level.
Specifications and other data subject to alteration without prior notice.
If your drill rig can’t reach the RPMs above please contact your local Epiroc
representative for recommendation.

COP RC45 HD kits, consumables, accessories

Description Product No. Product code
Seal kit 89012400 9704-RC-00-66B-91-000-K30
Check valve kit 89011569 9704-RC-00-000-00-000-K17
Rebuild kit 89012469 9704-RC-00-66B-91-H00-K40
Backhead assembly 89012462 9704-RC-00-66B-00-H00-A20
Casing 89012461 9704-RC-00-000-00-H00-004
Inner tube assembly 89011499 9704-RC-00-000-91-000-R95
Inner tube adapter
89012365 9704-RC-00-66B-00-000-R94
assembly
Grinding wheel, 14 mm 87001025 9500-1025
Grinding wheel 15,8 mm 87005166 95-3-DC-0158-Tru,H
Grinding wheel, 16 mm 87001027 9500-1027
Grinding wheel, 19 mm 87003966 9500-3966
Grinding wheel,
87005167 9500-3966
Trubbnos 19,1 mm
Wrench NV102 89000667 8484-0214-13
Bit holder 87004605 9500-4605
COP RC configurator
Rig/Type of pipe DR102 DR102OF DR115 DR115OF M40 M45 M45 OF R40 R45

D60/65RC, L8RC x x x x 89001539 89001517 89012457 x x

E235 (6 m) 89001442 89010238 89001396 89010263 89010208 89001560 89012457 89010309 89010279

E100 (3 m) 89001440 89010240 89001422 89010265 89010206 89001556 x 89010307 89010285

E50 89001440 89010240 89001422 89010265 89010206 89001556 x 89010307 89010285

DML (9,14 m) x x x x x 89010365 x x x

Other 6 m std
89001442 89010238 89001396 89010263 89010208 89001560 89012457 89010309 89010279
wrenching

Other 3 m std
89001440 89010240 89001422 89010265 89010206 89001556 x 89010307 89010285
wrenching

Our online RC configurator tool is easy and simple to use. manufacturer. Products from different manufacturers must
With a little input to the configurator you get a complete never be used together. This may cause extensive wear or
drill string proposal. All our RC strings can be found in the early breakages.
configurator. This makes it a perfect tool weather you are
The RC configurator can be found here: http://rchammer.
creating your own comprehensive selection of drill string
secoroc.se
equipment or just looking for a part number.
For more information please contact your closest Epiroc
We recommend to change the whole string from top
customer center.
sub/saver sub to bit sub/dig out and use the same
.

The COP RC45 is also available in a HD

version, for extra demanding conditions.

What is COP RC45 HD?

• The HD is not high definition, but it has the same message
– more bang for the buck.
• The heavy-duty version gives you longer service life, less
service related issues and at the end of the day higher
productivity and increased profit.
• What sets the HD version apart, is the attention we put
into the details. We used our years of experience to select
the best material and the best heat treatment available.
• COP RC 45 and COP RC45 HD are multi-purpose
hammers suitable for all RC applications.
 “Surprised in a positive way"
COP RC45 “Saves diesel"
“Makes us more compatible"
hammer: “One move inspection"
“Can be relied on"
“Never seen a hammer that

– Easy
works like on steroids"
Ricky Jackson
Operations manager, project in Tomingley, NSW

going!
A hammer that is robust
and easy to drill with, was
the very first mission for the
Atlas Copco Secoroc team
in Fagersta, Sweden. They
dedicated their efforts in
combining the best materials
with the best heat-treatment
technologies. And in one
of Europe’s largest heat-
treatment plants, the one in
Fagersta, the hammer was
born.

Case
When the team went to the project in that’s why the hammer is frequently
Tomingley, NSW, to test the Secoroc checked by the driller to see what
COP RC45, they were quite skeptical the wear level was. Usually operators
about it and for some reasons; are not very happy with regular
The roughness of the Australian inspections, but with the COP RC45
environment in which the RC drilling it took literally a second – you just
equipment was found and developed replace the inner tube with one move.
during many years of trial and error, The hammer’s inner tube lasted three
and direct in-put from drillers, put times the life of the pipe inner tubes!!!
the bar very high for every new RC
– I am very satisfied with the diesel
hammer.
consumption for the drill rig too. The
The Operations manager, Ricky hammer uses the air in a very efficient
Jackson, shares with us his first way, which, for me, means less
impressions after the Secoroc COP expenses and makes my company
RC45 hammer was put on test: influenced not only the performance, more competitive in the cost per
but also the quality of the sampling meter deals, says Operation manager
– When we increased the pressure of
material. Ricky Jackson.
the drill rig up to 30 bar the hammer
went crazy, like it was on steroids. The – I expected that the high
high frequency, that we have never performance would lead to an Veselin Donchev,
seen until the COP RC45 hammer, extensive wear of the inner-tube and Product manager, RC
 9866 0046 01 Subjected to alterations without prior notice. © Epiroc Drilling Tools AB. All rights reserved. 2017.12.

United in performance.
Inspired by innovation.
Performance unites us, innovation inspires us, and
commitment drives us to keep moving forward.
Count on Epiroc to deliver the solutions you need to
succeed today and the technology to lead tomorrow.
epiroc.com

Epiroc Drilling Tools AB

Box 521, SE-737 25 Fagersta, Sweden
Phone: +46 223 461 00