SIMBA

M6
Hydraulic production drill
rig for long-hole mining and
medium-to-large holes ranging
from 51 to 178 mm in diameter.
 SIMBA
HIGH PRECISION SOLUTION
THE STURDY SIMBA M6 IS A LONG-HOLE PRODUCTION DRILL RIG FOR MEDIUM
TO LARGE-DRIFT MINING. IT ACCOMMODATES A RANGE OF DRILL BITS, ROCK
DRILLS AND IN-THE-HOLE HAMMERS TO ADAPT TO YOUR SPECIFIC NEEDS. THE
RIG OPERATOR ENJOYS EXCELLENT VISIBILITY AND ENHANCED SAFETY IN THE
COMFORTABLE CABIN. WHEN YOU SEEK A HARD-WORKING, HIGH-PRECISION
SOLUTION FOR LONG-HOLE DRILLING, RELY ON THE POWERFUL SIMBA M6.

MAIN BENEFITS
Sturdy and precise The Simba M6 drilling unit is mounted on an
I-frame with a pendulum arm for easy setup and steady, accurate
drilling.

Suits your needs The Simba M6 can accommodate a wide range

of top-hammers and in-the-hole hammers to best suit your opera-
tion and optimize your performance, hole quality and drill steel
economy.

Precision and productivity The Simba M6 features our acclaimed

rig control system (RCS) and can be equipped with smart
automated single-hole or multi-hole drilling functions. With
tele-remote control, the Simba M6 can be operated from
one or more remote locations.

2
The bit changer increases efficiency and
keeps the operator at a safe distance
from the drilling zone.

The cabin is ROPS and FOPS approved for

a safe, ergonomic operating environment.

The reverse camera enhances visibility and

safety while transporting the drill rig.

3
 FAST AND PRECISE ROCK DRILLING
SIMBA M6
SIMBA M6 MODELS ARE BUILT FOR FAST ON-SITE POSITIONING AND
ACCURATE HOLE PLACEMENT. INTELLIGENT FUNCTIONS ON THESE
HIGH-PERFORMANCE RIGS BOOST EFFICIENCY AND PRODUCTIVITY
WHILE MAKING THE OPERATORS JOB SAFER AND EASIER.

+ SAFETY
The Simba M6 is designed with safety in mind. The rig operator sits in
a ROPS and FOPS-approved cabin that offers excellent visibility and
comfort. Barrier sensors protect the operator and other workers from
rotating parts during automatic drilling.

+ AUTOMATION
Boost your productivity by equipping your Simba M6 with smart
automated functions such as ABC Regular or ABC Total. Your Simba M6
can then effectively continue to drill unattended throughout personnel
breaks and shift changes. With the tele-remote control function, the rig
operator can safely and comfortably command the rig from a distance.

+ ATLAS COPCO RIG CONTROL SYSTEM

We introduced the first version of our computerized drill rig control
system in 1998 to take the market by storm. Throughout the years, the Rig
Control System (RCS) has been further advanced and refined to include
increasingly sophisticated functions informed by practical work experience
and an on-going dialogue with clients. More than 3 000 RCS-equipped rigs
are currently in operation the world over. At Atlas Copco, we continue to
drive development in the drilling and mining industry.

ATLAS COPCO SERVICE

+ WORLD CLASS SERVICE
ITS
FlexiROC T35 andNOT JUST
FlexiROC T40 ABOUT
are flexible and versa-

highOUR PROMISES, ITS

tile tophammer drill rigs, developed and designed for
performance in demanding construction appli-
ABOUT DELIVERY
cations. They are also a very efficient alternative for
small and medi um size quarrying jobs. Even in tough
terrain conditions, utilization of the rig is high, thanks
We offer several levels of service to meet the
to the long reach of the boom,
requirements of your operation and ensure your
FlexiROC T35 and FlexiROC T40 are flexible and versa-
productivity. Choose a service agreement that
tile tophammer drill rigs, developed and designed for
will help you build a quality operation. Minimize
high performance in demanding
unplanned downtime through proactive, planned
maintenance. We offer expert advice and
maintenance on every machine, component
and accessory in our inventory.

4
 = STANDARD = OPTION
TECHNICAL SPECIFICATIONS
A = SIMBA M6 B = SIMBA M6-ITH

DRILLING SYSTEM A B CONTROL SYSTEM A B

COP 1838+ Atlas Copco Rig Control System (RCS)
COP 1838MUX+, COP 1838HUX+ Advanced Boom Control (ABC) Regular
COP 2550UX+ Advanced Boom Control (ABC) Total
COP 3060MUX Breaktrough Automatic Stop
COP 4050MUX Underground Manager pro
COP 44 to COP 64 Drill plan handling
Dry drilling system Drill plan handling with raise view
Collar Pipe Inserter (CPI) Full Drilling Data Handling
Thread lubrication kit Measure While Drilling (MWD)
Bit changer Void Detection
Water mist flushing, external water and air supply (Hydraulic oil cooled by Remote Cradle Control/Remote Feed Control

water cooler) Rig Remote Access (RRA)
Water mist flushing, external water and air supply (Hydraulic oil cooled by air fan) Mobile Tele Remote/Multi Tele Remote
Hole blowing kit Remote operating kit
Rock drill lubrication warning kit Additional panel
Remote controlled camera on tripod with monitor in cabin
BOOM
BOOM/DRILLING UNIT A B A
C D
B Total Station Navigation
Automatic lubrication for drilling and positioning unit Certiq professional
Central lubrication for drilling and positioning unit
Rod Handling System, RHS 17 (17+1 rods) Mechanized drilling up to 32 m ELECTRICAL SYSTEM A B
Rod Handling System, RHS 27 (27+1 rods) Mechanized drilling up to 51 m Total installed power 118 kW (Main motors 2 x 55 kW)
Rod Handling System, RHS 35 (35+1 rods) Mechanized drilling up to 63 m Total installed power 63 kW (Main motor 1 x 55 kW)
Adaptable to 4', 5' and 6' rods Total installed power 158 kW (Main motor 1 x 95 kW, Equipped with booster

Adaptable to 5' and 6' rods compressor)
2 x Rear and 2 x front stinger Total installed power 158 kW (Main motors 2 x 75 kW)*
Voltage 400-1 000 V 50/60 Hz
Starting method star/delta (400-690 V)
FEED A B
Soft start of main electrical motors (not for 1000 V)
BMH 200-Series 3 160 mm, 3 465 mm, 3 770 mm
Electronic overload protection for electric motors
BMH 200-Series (Extractor) 3 365 mm, 3 670 mm, 3 975 mm
Digial voltmeter/amperage meter in electric cabinet
BMH 200-Series 3 620 mm, 3 925 mm
Electric outlet for accessories, 16 A (CE) / 32 A (CE)
Extra transformer 15 kVA
AIRSYSTEM A B PC4 or PC5 Plug/Socket
Air flow guard Phase sequence and eart fault indicator
Compressor: Atlas Copco GAR 5 Battery charger
Compressor: Atlas Copco GAR 30 Dual controls for cable reel
Compressor: Double GAR 30 +air receiver Limit switch for cable reel with signal lamp and brake connection
Compressor: On-board booster, 25 bar/ 380 l/s Stainless steel electrical enclosure
External air supply connection for hole blowing *Only when equipped with COP 3060MUX and COP 4050MUX.
HECL lubrication system with electric filling pump

WATERSYSTEM A B
Minimum water inlet pressure 2 bar
Hydraulic water booster pump. Capacity, at 15 bar 250 l/min
Water injection pump. Capacity 50 l/min
Water hose reel including hose*
*Not applicable when booster compressor is installed on ITH drill rigs

HYDRAULIC SYSTEM A B
Low oil level indicator and shut-down
Smart oil leakage shut-down system
Oil temperature gauge on oil tank, electronically supervised
Hydraulic oil thermostat
Water/Oil cooler in stainless steel
Filtration 16 m
Oil filter indicator
Mineral hydraulic oil
Electrical oil filling pump
Heater kit for hydraulic oil tank, diesel engine and electric motors
Biodegradable hydraulic oil
Nr-Cr plated piston rods (limited selection on request)

5
 = STANDARD = OPTION
TECHNICAL SPECIFICATIONS
A = SIMBA M6 B = SIMBA M6-ITH

CARRIER A B DRIFTER RODS/PIPES

Deutz TCD 2013 L04 2V Stage III A Tier 3 (120 kW) Rock drill Rod/Pipe Guide tubes Min. hole diameter (mm)

Deutz TCD 4.1 L04 Stage IV / Tier 4F (115 kW) R32 Speedrod TDS 45 51-64
COP 1838+, T38 Speedrod
Deutz TCD 2012 L06 2V Stage III A Tier 3 (155 kW) TDS 54/TDS 64 64-76
HUX+,MUX+
Deutz TCD 6.1 L06 Stage IV / Tier 4F** T45 Speedrod TDS 64/TDS 76 76-89

Front axel DANA Spicer 123/90 T51 TDS 76 76-115

COP 2550UX
Rear axel DANA Spicer 123/90 8 oscillation TDS 64/TDS 76 N/A 89-102 (ST58 Shank adapter)

Articulated steering 41 steering angle TDS 76 N/A 89

COP 3060MUX
Four-wheel drive TDS 87 N/A 102

Electric system 24 V TDS 76 N/A 89

COP 4050
Batteries 2 x 125 Ah TDS 87 N/A 102-147

Hose/cable guiding at water/cable reel COP 44 TAC 76/89 N/A 110-125

Automatic differential lock on front axle, limited slip COP 54 TAC 89 (TDS102) N/A 134-152

Tires 12 x R24 COP 64 TAC 89 (TDS102) N/A 156-178

Tramming lights 8 x 22 LED, 24 V DC

Working lights 4 x 150 LED, 24 V DC RECOMMENDED CABLE SIZE AND LENGTH

Rig alignment laser Voltage Type Dimension (mm2) Diameter (mm) Length (m) Length ITH (m)

Illuminated stairs for platform LED 380-400 V Buflex 3x185+3G35 56 80 65

440-500 V Buflex 3x150+3G25 52 120 70
Front and rear jacks
550 V Buflex 3x120+3G25 46 120 95
Fuel tank, volume 110 L
660-690 V Buflex 3x95+3G16 45 150 125
Central grease point 1 000 V Buflex 3x50+3G10 33 200 200
Fire suppression system ANSUL (manual or automatic) Recommendations are given for surrounding temperature of 40 C and up to a height of 2 000 m.
Fire suppression system FORREX (manual or automatic)

Hot climate tramming kit NOISE AND VIBRATION

Rig washing kit* Operator sound pressure level in canopy, drilling, free field 1046 dB(A) re 20uPa
(ISO 11201)
Manual lubrication kit
Operator sound pressure level in cabin, drilling, free field 75 3 dB(A) re 20uPa
Boot washing kit* (ISO 11201) 75 3 dB(A) re 20uPa (DH)
*Not applicable when equipped with dry drilling system. Operator sound pressure level working close to machine, 1046 dB(A) re 20uPa
**Maximum ambient temperature 25 drilling, free field
Peak C-weighted instantaneous sound pressure level Less than 130 dB
(EN16228)
CABIN (OPTIONAL) A B Sound power level (ISO 3747), drilling, free field 128 dB(A) re 1pW
ROPS and FOPS approved cabin Vibration levels seated, drilling (ISO 2631-1) 0.07 0.07 m/s^2
Mounting height -140 mm Vibration levels standing, drilling (ISO 2631-1) 0.070.07 m/s^2

Cabin lift/tilt system, 375 mm/15

Swingable seat for drilling and tramming RECOMMENDED DRIFT SIZE

Front window 22 mm (P8B safety classified) Feed Rod Minimum (H x W)
BMH 214/234 1 220 4 600 x 3 600 mm
Reversing camera with monitor
BMH 215/235 1 525 4 900 x 3 900 mm
12 V Outlet
BMH 216/236 1 830 5 200 x 4 200 mm
Joystick-controlled spotlights left and/or right, 70 W

FOPS-approved grizzly bar for front window

DIMENSIONS
Low-designed cabin, for seated operator cabin height 2 735 mm
Measurement Simba M6 Simba M6 ITH
Mediaplayer
Width 2 210 mm 2 210 mm
Air condition
Height with cabin 3 100 mm 3 100 mm
Heating function for air conditioning (water transferred) Height roof up/down 3 050/2 945 mm 3 144/2 518 mm
Electrical heater, 1.2 kW, 230 V (CE) Length tramming 10 420 mm 10 720 mm
Cabin body made of stainless steel Ground clearence 265 mm 265 mm
Turning radius outer/inner 6 900/3 800 mm 7 625/4 750 mm

PROTECTIVE ROOF A B
FOPS approved TRAMMING SPEED
Swingable seat for drilling and tramming On flat ground >15 km/h
On incline 1:8 >5 km/h
Stainless steel

Joystick-controlled spotlights left and/or right, 70 W

GROSS WEIGHT (DEPENDING ON CONFIGURATION)
Rig type Total Boom side Engine side
Simba M6 26 000 kg 14 500 kg 6 400 kg

6
TECHNICAL SPECIFICATIONS

www.atlascopco.com
3 100

M6 C

M6 C

2 023
2 900 3 740 3 780
10 420

Simba M6/Simba M6-ITH

www.atlascopco.com
3 100

M6 C-ITH

M6 C-ITH

2 050
3 200 3 740 3 780
10 720

Simba M6-ITH, equipped with booster compressor.

RD = Ring drilling 3 000 (PH) Dimensions

Stinger extension
PH = Parallel holes in mm
1 150
900

Feed extension
1 200 (900)
o
30 45 o
R
48
80
5 650

(R

o 45 o
5 000

D)

45
(RD)
R 2 760 380o
2 780

150

8 520 Stinger extension

A-A 2 000
A
Coverage area

7
 COMMITTED TO SUSTAINABLE PRODUCTIVITY
We stand by our responsibilities towards our customers,
towards the environment and the people around us. We

This is what we call Sustainable Productivity.

make performance stand the test of time.

www.atlascopco.com
9851 3470 01b 2016-11 rebro, Sweden. Legal Notice Copyright 2016, Atlas Copco Rock Drills AB, rebro, Sweden. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations
and photos may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer
Center for specific information.