Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 16 views

    TW580

    Uploaded by

    TAHRI BELGACEM
    The document provides instructions for installing and repairing a diaphragm protector. It describes loading the system by pumping fluid through the protector and ensuring no air bubbles remain. It also lists parts for different protector models.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    TW580

    Uploaded by

    TAHRI BELGACEM
    16 views2 pages
    The document provides instructions for installing and repairing a diaphragm protector. It describes loading the system by pumping fluid through the protector and ensuring no air bubbles remain. It also lists parts for different protector models.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for installing and repairing a diaphragm protector. It describes loading the system by pumping fluid through the protector and ensuring no air bubbles remain. It also lists parts for different protector models.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    16 views2 pages

    TW580

    Uploaded by

    TAHRI BELGACEM
    The document provides instructions for installing and repairing a diaphragm protector. It describes loading the system by pumping fluid through the protector and ensuring no air bubbles remain. It also lists parts for different protector models.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    r

    TECHNICAL MANUAL
    ~17ANDE91DIAPHRAGM
    PROTECTOR SUPERSEDES
    C==ah
    OCT. 1979
    PfilNTED IN U S A.

    INSTALLING THE PROTECTOR: hand pump from check valve. Replace and
    tighten check valve cap on check valve (Item 1).
    Install Protector in a vertical position to allow Push in on the damper stem and turn clockwise
    the well fluids, cement, etc., to drain out of to engagethe threads. The damper stem may
    the cup when the instrument is not operating. be adjusted for desired damping effect in use.
    Replace and tighten on protector union.
    A shut-off should be installed betweenthe flow
    line and the Protector for inspection and/or REPAIRS:
    repairs of the protector and gage system.
    If check valve (Item 1) is broken off in protector
    Install the two inch female sub half of the Pro- housing (Rem 4) remove broken off portion with
    tector on a vertical riser. Before the housing an easy out. Replace with a new F330-1 check
    of the protector is installed, check for correct valve and follow loading procedure. The F350-1
    amountof hydraulic fluid in the gagesystem. check valve has a l/4 NPT.
    The diaphragm cup (Item 2) which can be
    observed through the bottom of the protector To replace E40 rubber diaphragm cup (Item 2).
    housing, should be collapsed so the sides of the
    rubber cup are touching. If the cup is round a. Remove check valve and hose from
    (Fig. 1) the system must be reloaded. See protector housing.
    loading the system below.
    LOADINGTHE SYSTEM: Unscrew hose fitting from protector
    Place protector housing in a vertical position housing. Do not unscrew hose coup-
    ling nut fro_mnipple.
    (top up). Removecheck valve cap (Fig. 1) from
    check valve (Item 1). Attach handpump to b. Remove J79 brass protection nut
    check valve (Fig. 2), but do not tighten. Fill (Rem 3). (Use MARTIN-DECKER nut
    handpump reservoir with MARTIN-DECKER wrench T589 if available).
    W15 fluid. Operate handpump plunger.slowly c. Remove rubber diaphragm cup from
    to bleed air from pump at check valve connec- protector housing.
    tion. Tighten hand pump on check valve (Item 1). d. Wash and clean inside of protector
    Keep fluidlevel in hand pump reservoir at least housing and open holes in protector
    one half full during loading procedure so that no housing. Clean small seal groove in
    air will be pumpedinto system. Turn damper protector body.
    stem on gageand/or recorder counter-clock- e. Press new E4O/E40-1diaphragm into
    wise several turns to relieve dampingeffect. protector housing msking sure rubber
    The damper stem is designedto disengagethe diaphragm flange is evenly in protector
    threads allowing openpassageof system for body groove.
    bleeding. Loosen the pipe’p lug on top of the f. Apply thread grease or lubriclnt (not
    gage and/or loosen the tubing connectionon the thread seal) to brass protection nut
    pressure tube socket inside the recorder. amI wrew into place. The brass pro-
    Pump fluid into the system and bleed at gage tection nut will be approximately flush
    and/or recorder until no air bubbles appear. with protector housingwhen properly
    A8 air will seek the highest level, the gage and/ installed, and the rubber diaphragm
    or recorder must be higher than the Protector cup will be held in place as shown. Do
    when the system is being loaded. The hose nal over- tighten, it will damagethe
    should be laid out straight if possible. Tighten rubber diaphragm cup.
    on gageand/or tubing connectionon g. Replace check v&e and hose on pro-
    . tector housing.
    h. Follow loading procedure.
    Pump enoughfluid into system to cause rubber
    diaphragm sides to touch as shawnin (Fig. 2).
    Do not over pump so that rubber diaphragm
    (Item 2) is forced into nut (Item 3). Remove

    M/D TOTCO
    El7 AND E91 DIAPHRAGM PROTECTOR MARTIN-DECKEWTECHNICAL MANUAL

    Check Valve
    Cap

    YA2
    Hand Pump (Ref)
    Hose (Ref),

    Figure 1. Diaphragm Protector Figure 2. Loading the System


    with Female Sub

    PARTS LIST
    ITEM PART
    NO. NO. DESCRIPTION QTY.
    1 1 F350-1 1 Check Valve with Cap
    2 IE40 1 Diaphragm Cup, Rubber
    1E40-1 1 Diaphragm CUP; Viton
    3 15’79 I Nut, Protection
    4 See Table Housing, Protector
    5 See Table Wing Nut
    6 See Table Sub, Threaded
    7 See Table Ring, Diaphragm Protector

    ASSEMBLY CAPACITY UNION MAKE HOUSING SUE3 DIAPHRAGM


    NO. PSI AND MODEL PROTECTOR WING NUT (THREADED) PROTECTOR RING
    El7-62* 6,000 Weco Fig. 602 El31 -3 J753-62 5754-62 B747
    E17-152 15,000 Weco Fig. 1502 El31 5753-152 5754-152 B747
    E91* 15,000 Guiberson #2072 5 El31 -1 5755 5756 B758
    J
    *Reference only, new assemblies not available, parts for replacement only.

    Page 2 ti81

    You might also like