SPC BASE MOUNT

SSB-135-02

DUPLEX 10 - 15
4107 9500 11.05
Page 1 of 4
14 February 2017
LifeLine® “Oil-Less” Scroll Medical Air
Single Point Connection (SPC) Base Mount
Duplex System (10 - 15 HP)

SPECIFICATION

Single Point Connection (SPC) System Design Air Receiver

The LifeLine® Oil-Less Scroll Medical air package is fully Corrosion resistant, ASME Coded, National Board Certified
compliant with NFPA 99 and features a common base with single vertical air receiver rated for minimum 150 PSIG design pressure.
point connections for electrical, intake air, discharge air, and
The air receiver assembly includes:
condensate drains. Designed and manufactured to ISO 13485
processes, each system is completely tested before shipment and • Zero Loss electronic drain valve, liquid level gauge glass,
includes: safety relief valve, and manual drain valve
• Two compressor towers, each with two “oil-less” scroll • Piped 3-valve bypass assembly with flange-fitted valves
compressors and one motor • Pressure gauge
• Duplex desiccant drying system with purge control
Dryer/Filter/Regulator System
• Integral pre-wired control panel
Each desiccant dryer is sized for peak calculated demand and
• Corrosion resistant vertical air receiver produces a 10° F (-12° C) pressure dew point. Each dryer
operates from a demand based purge saving control system
Compressor Module featuring repressurization cycles. The dryer assembly includes
The compressors are continuous duty rated scroll type, single the following mounted and piped:
stage and air-cooled. The compressors have one fixed and one
orbiting scroll sealed with PTFE tip seals. • 441™ transfer valve utilizing two sliding ceramic plates with a
5-year warranty
• Field replaceable tip seals
• High efficiency coalescing prefilter rated for 0.01 micron with
• Dust and contamination protection from two part face seal automatic drain and element change indicator
• Orbiting bearing and pin crank bearings are grease filled • Fully duplexed final line particle filters rated for 1 micron
• Heat dissipation maximized by an integral cooling fan with element change indicators
• V-belt driven compressor protected by totally enclosed • Duplexed final line regulators and safety relief valves
beltguard • Ceramic type dew point sensor with ± 2° F system accuracy
• Fully adjustable motor mounting base to achieve belt • CO Sensor with ± 2 PPM (at 10 PPM) system accuracy
tensioning
TotalAlert Embedded Control System
Compressor Motor The duplex mounted and wired TotalAlert Embedded control
The motor is NEMA rated, open dripproof and operates at 3600 system is U.L. labeled. The control system provides automatic
RPM with 1.15 service factor suitable for 230/460V or 208V lead/lag sequencing and automatic alternation of both
electrical service. compressors based on first-on/first-off principle with provision
for simultaneous operation if required.
Compressor Assembly
• NEMA 12 control panel enclosure
The piped intake manifold includes one inline inlet air filter and
isolation valve per compressor and a high inlet vacuum switch • Circuit breaker disconnects for each motor with external
to protect the compressors. The compressor discharge assembly operators
includes: • Full voltage motor starters with overload protection
• Integral air-cooled aftercooler with a maximum approach • 24V control circuit
temperature of 15°F above ambient and integrated drain trap The touch screen controls feature one 5.7” master screen and a
with automatic solenoid drain valve 3.5” operating screen for each compressor. Screen displays and
• Discharge lines include heat-shielded flex connector, safety functions include:
relief valve, isolation valve and check valve • Service alerts, runtime hourmeters, system status, system
• Integral valve per compressor provides load-less starting and pressure level, dew point level, CO level
rapid air evacuation at shutdown • Visual/audible alarm indications with isolated contacts for all
standard remote alarms
Isolation System
• Event log recording alarms and system activity
Four-point, heavy duty isolation system for a minimum 95%
• Event log recording service warnings and service history
isolation efficiency fully isolates the compressor / motor tower
from the system. Finite Element Analysis conducted to minimize • Trend graphs for outlet pressure, Dew Point, CO, and ambient
vibration transfer. Seismically restrained isolators are available. temperature
• Ethernet connectivity and embedded web page for remote
monitoring
• Electronic notifications of alarms and warnings
• Integral connectivity to the TotalAlert medical gas network via
Ethernet

BeaconMedæs • 1059 Paragon Way, Rock Hill, SC 29730 • Phone: (803) 817-5600 • Fax: (803) 817-5750 • www.beaconmedaes.com
 SSB-135-02
4107 9500 11.05
Page 2 of 4
14 February 2017

Standard Configuration
Model Shown: 15 HP Duplex Control panel pre-drilled for power,
1 alarms, and Ethernet connections for
easy electrical installation.

TotalAlert Embedded touch screen

controls featuring 5.7” master screen
2
and (2) 3.5” operating screens with
1 exceptional clarity and visibility.

Motion sensor to activate touch screen

3 3 displays, preserving screen life.
7 Inlet connection positioned for
2 4 pipework attachment without stress on
system.

High inlet vacuum switches to protect

the compressors in the event the
5
inlet valve is closed or inlet filters are
clogged.

4-point heavy-duty isolation system for

5 95% isolation effciency of compressor
6 tower. Further vibration isolation
achieved with flex hoses on intake and
discharge.
4
Individual air inlet filter per compressor
7 to protect compressors from incoming
debris.
6

Aftercooler with separate cooling

fan to provide maximum approach
8 temperature of 15° F above ambient
ensuring efficient dryer operation.

Zero-Loss electronic discharge drain

9 to save compressed air and remove
moisture efficiently.

Manifold dryer block design with SAE

10 fittings to reduce potential leak points
and to reduce pressure drop losses.

441® ceramic plate dryer switching

11 valve with 150 million cycle anticipated 13
life to reduce maintenance and 8
downtime costs.

Anodized aluminum blocks and flanged 10

12 fittings utilized throughout air stream
design to reduce leak points. 9
Dryer towers with repressurization 11
13 cycle to eliminate desiccant shock and
minimize desiccant dusting. 14
12
High efficiency inlet and outlet filters to
14 protect the desiccant beds and medical
air stream.
 SSB-135-02
4107 9500 11.05
Page 3 of 4
14 February 2017

TotalAlert Embedded Control System

TM

EMBEDDED

Touch Screen Control Master Display Screen (5.7”)

• Master screen is 5.7” high-resolution LCD with 640x480 pixel • Main Screen
display and Unit screens are 3.5" high-resolution LCDs with xx Displays the system operating conditions, including System
240x320 pixel display for exceptional clarity and visibility Pressure, Dew Point and CO level
• Toolbars on all screens with easy access navigation icons that xx Displays the compressor unit sequence, including status of
enable full access with minimal touches compressors (running, available, off) and next to start
• PIR motion sensor activates screen display (under alarm • Trends & Graphs
conditions screen is active continuously) xx Shows measured values of the system operating conditions
over a period of time (operating pressure, Dew Point, CO,
Ethernet Connectivity with Embedded Web Page
ambient temperature)
• Built-in web server allows remote operator to view system
xx Selectable time periods consist of 60 min, 4 hrs, 24 hrs, and
controls and display information
6 days
• Ethernet communication compatible with TotalAlert and
• Dryer Information
TotalAlert2 alarm systems
xx Displays the operating mode of the dryer(s)
• Web page provided to show links to other devices on the
TotalAlert Embedded network, including alarms and other xx Displays dryer image showing current status
source equipment • Service
• Electronic notification xx Displays ambient temperature in the room
xx Accessible through any SMTP gateway xx Maintenance screen shows suggested and required
xx Allows for remote alerts of alarm and warning conditions maintenance items with resettable timers
xx Allows for remote alerts of routine maintenance xx Historical event log records all service activities
• All printed circuit boards have an Ethernet port that allows • Alarms and Shutdowns
reprogramming with a standard computer for software updates xx All system Alarms and Shutdowns displayed with visual
• Dual Ethernet configuration with separate Ethernet subnets indication (Green or Red)
to separate the facility Ethernet from internal TotalAlert xx Testing mode enables operator to test all alarm events
Embedded communications (password protected)
xx Event History Log records all system event history
Control Cabinet Safety
• System Settings
• Volt free relay contacts for all standard alarms
xx Allows the adjustment of system pressure operating range
• Low voltage (24V) control circuit (password protected)
• Full voltage motor starters with overload protection xx Displays pertinent system model information
• Circuit breaker disconnects for each compressor
Unit Screens (3.5”) - One per Compressor Unit
Redundancy • Main Screen shows the operation mode of the unit along with
• In unlikely event of display boards or displays becoming the automatic or manual mode setting
disabled, unit will function normally and activate alarm • Unit status screen displays the running hour meter values
• If master board is disabled, system goes to failsafe operation • Pump rotation allows the unit to run for a short period to
with backup pressure switch check pump rotation
• Each compressor and dryer unit has independent board for • All unit Alarms and Shutdowns displayed with visual
control allowing unit to function independently indication (Green or Red)
• Audible indication for unit Shutdown Alarms
• Testing mode enables operator to test all shutdown events
(password protected)
 SSB-135-02
4107 9500 11.05
Page 4 of 4
14 February 2017
Standard Configuration

15 Hp Dpx/200 gal shown

Notes: • Inlet & discharge flex connections are built into package.
• Allow 36 inches in front of control panel for maintenance and ventilation, all other sides require 24 inches of clearance.
• Additional drawings/diagrams available for download at www.beaconmedaes.com.
Medical Air System Specifications1
Dimensions
System System FLA System
System Model System3 Receiver Noise4 (in.)
HP Capacity2 Weight
No. BTU/HR (gallons) Level 380V
50 psig 208V 230V 460V (lbs.) H
50 Hz
SAS10D-120V-D 10 34.8 23,014 120 73 52.2 49.3 24.9 27.8 2002 81.9”
SAS10D-200V-D 10 34.8 23,014 200 73 52.2 49.3 24.9 27.8 2220 85.1”
SAS10D-240V-D 10 34.8 23,014 240 73 52.2 49.3 24.9 27.8 2300 97.1”
SAS15D-120V-D 15 50.4 34,124 120 75 73.4 71.3 35.9 42 2130 81.9”
SAS15D-200V-D 15 50.4 34,124 200 75 73.4 71.3 35.9 42 2350 85.1”
SAS15D-240V-D 15 50.4 34,124 240 75 73.4 71.3 35.9 42 2430 97.1”
Notes: 1. Normal operating conditions at a maximum ambient of 105° F. Consult factory for higher ambient conditions.
2. All capacities are shown as NFPA system capacities (reserve compressor on standby) and are shown in Inlet Cubic Feet per
Minute (ICFM).
3. All system BTU/HR are shown with reserve compressor on standby.
4. All noise levels are shown in dB(A) and reflect one pump running.
5. System is designed for output pressure of 50-60 psig (344-413 kPa). For alternate pressures contact factory.

BeaconMedæs
1059 Paragon Way
Rock Hill, SC 29730
Phone: (803) 817-5600
Fax: (803) 817-5750
www.beaconmedaes.com