Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 5K views

    Rollers and Slip Gauges

    Uploaded by

    Anand Babu
    This document describes measuring the taper angle of a specimen using three methods: rollers and slip gauges, a sine bar, and a bevel protractor. Slip gauges of equal heights are placed on either side of the specimen and measurements are taken over rollers using a micrometer. The taper angle is calculated using these measurements and heights. A sine bar is also used to indirectly measure the angle based on trigonometry by inserting slip gauges under one roller. The measured angles from both methods are then verified with a bevel protractor. Precise measurements and cleaning of equipment is important for accurate results.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    Rollers and Slip Gauges

    Uploaded by

    Anand Babu
    5K views6 pages
    This document describes measuring the taper angle of a specimen using three methods: rollers and slip gauges, a sine bar, and a bevel protractor. Slip gauges of equal heights are placed on either side of the specimen and measurements are taken over rollers using a micrometer. The taper angle is calculated using these measurements and heights. A sine bar is also used to indirectly measure the angle based on trigonometry by inserting slip gauges under one roller. The measured angles from both methods are then verified with a bevel protractor. Precise measurements and cleaning of equipment is important for accurate results.

    Original Description:

    METRO LOGY LAB EXPERIMENT

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes measuring the taper angle of a specimen using three methods: rollers and slip gauges, a sine bar, and a bevel protractor. Slip gauges of equal heights are placed on either side of the specimen and measurements are taken over rollers using a micrometer. The taper angle is calculated using these measurements and heights. A sine bar is also used to indirectly measure the angle based on trigonometry by inserting slip gauges under one roller. The measured angles from both methods are then verified with a bevel protractor. Precise measurements and cleaning of equipment is important for accurate results.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    5K views6 pages

    Rollers and Slip Gauges

    Uploaded by

    Anand Babu
    This document describes measuring the taper angle of a specimen using three methods: rollers and slip gauges, a sine bar, and a bevel protractor. Slip gauges of equal heights are placed on either side of the specimen and measurements are taken over rollers using a micrometer. The taper angle is calculated using these measurements and heights. A sine bar is also used to indirectly measure the angle based on trigonometry by inserting slip gauges under one roller. The measured angles from both methods are then verified with a bevel protractor. Precise measurements and cleaning of equipment is important for accurate results.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 6

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    MEASUREMENT OF TAPER ANGLE USING ROLLERS SLIP GAUGES AND SINE BAR

    10

    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR
    AIM:

    To determine the taper angle of the given specimen using slips & rollers and Sine Bar and check the angle using Bevel Protractor.

    APPARATUS: Two rollers of equal diameter, Micrometer, Sine Bar, slip gauge

    set.
    THEORY:

    Taper is defined as uniform reduction in dimension (may be width, height or diameter) over specified length. For example for the shank of a twist drill bit, if the taper is specified as 1:10, it means that for every 10 mm length there will be a reduction of diameter by 1 mm (from major to minor dia). Taper is employed on elements like cotter, keys and shanks of twist drill bits, end mills, reamers adapters etc. Presence of taper enables self locking of the element in the corresponding mating part. Slip Gauges: Slip gauges for rectangular blocks of alloy steel having a cross section of about 30 by 10 mm. These blocks are carefully finished on the This is measuring faces to such a fine degree of finish. Flatness and accuracy that any two such faces when perfectly clean may be wiring together. twisting motion whilst maintaining contact pressure. accomplished by pressing the faces into contact and then imparting a small When two gauges are wrung or more blocks so joined is exactly the sum of the constituent gauges. By combining gauges from a suitably arranged combination, almost any dimension may be built up.

    11

    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    Experimental Set Up:

    Fig.1

    Fig.2

    Fig 3.

    12

    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    PROCEDURE:

    1. Place the Taper specimen on the surface plate as shown in the figure. 2. Pile up slip gauge combinations of equal heights H1 and place them on opposite sides of taper specimen. 3. Place two rollers of equal diameter on slip gauge combinations. 4. Take measurement over the rollers with the help of micrometer (say M1) 5. Take slip gauge combinations of another height H2 and repeat steps 3 and 4 let the measurement over the rollers be M2 6. If is the included angle of taper specimen. Taper angle may be obtained as follows: Tan /2 =
    M 2 M1 2( H 2 H 1 )

    7. To check the uniformity of taper H2 may be varied by two to three values and may be calculated. 8. Verify the obtained taper angle using Bevel Protractor. SINE BAR Sine Bar is a precision instrument used along with slip gauges for the measurement of angles sine bar is used: (i) (ii) to measure the angles very accurately to locate the work to a given angle within very close limits It consists of a steel bar and two rollers. The sine bar is made of high carbon, high chromium corrosion resistant steel, suitably hardened, precision ground and stabilized. The rollers are of accurate and equal diameters. They are attached to the bar at each end. The axes of these rollers are parallel to each other and also to the upper surface of the bar. The normal distance between the axes of the rollers is exactly 100 mm, 200 mm or 300 mm. When the rollers are brought in contact with a flat surface, the top of the bar is parallel to the surface. The various parts are hardened and stabilized before grinding and lapping. All the working surfaces of the bar and the cylindrical surfaces are fined to surface finish of 0.2 m. A grade sine bar is made with an accuracy of 0.01 mm/m of length, and B grade sine bars with an accuracy of 0.02 mm/m of length. 13 MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    Sine Bar

    Slip Gauges

    Work Piece

    Surface Plate

    Principle of Sine bar: The principle of operation of a sine bar is based on the laws of trigonometry. To set a given angle, one roller of the bar is placed on the surface plate and the combination of slip gauges is inserted uner the second 14
    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    QIS COLLEGE OF ENGG. & TECH.ONGOLE,A.P.

    METROLOGY LAB

    roller. If h is the height of the combination of slip gauges and L the distance between the rollers centers. Then Sin =
    h h or = Sin 1 L L

    Thus the angle to be measured or to be set is determined by indirect method as a function of sine, for this reason, the device is called a sine bar.

    Checking of Measured Angle: The measured angle is verified using Bevel Protractor.
    PRECAUTIONS:

    1. Slip blocks must be cleaned properly and wrung together. 2. Micrometer readings must be observed without parallax error.

    RESULT:

    Taper angle of the given specimen. By Rollers slips By Sine Bar = =

    By Bevel protractor =

    15

    MEASUREMENT OF TAPER ANGLE USING ROLLERS & SLIP GAUGES AND SINE BAR

    You might also like