IronwoodPremium_474115_Catalog-On-Demand8.

QXD 6/16/2015 11:59 PM Page 327

Accessories for 69/72,5 kV

3M™ Cold Shrink QT-III Termination Kit 7673-S-8 Series for 69/72,5 kV

High Voltage Joints and Terminations, 72,5–145 kV

The 3M™ Cold Shrink QT-III Termination Kit 7673-S-8 Series are designed to terminate 69 kV, 650 mil solid dielectric, tape shield, longitudinally
corrugated (LC), jacketed concentric neutral (JCN), tape-over-wire (TOW), or wire-over-tape (WOT) shielded power cable. Covering a conductor size range
of 350 kcmil–3000 kcmil (185-1500 mm²). See the selection table for detailed sizing information.
Kit contents: Each kit contains sufficient quantities of the following materials as appropriate to make one single-phase termination (lug not included
unless requested in advance.)
2 Silicone Rubber Skirted Stress Control Assembly
2 Hi-K Stress Control Adapter Assembly
2 Lug Seal Tube
2 Ground Seal Tube
2 Ground Strap Assembly
2 Constant Force Springs
2 Tubes 3M™ Red Compound P55/R (Non-Silicone Grease)
2 Scotch® Electrical Shielding Tape 24
2 3M™ Scotch-Seal™ Mastic Sealing Tape 2229
2 3M™ Copper Foil Shielding Tape 1181
2 Scotch® Vinyl Electrical Tape Super 88
2 3M™ Cable Cleaning Pads CC-3
2 Scotch® Self-fusing Silicone Rubber Tape 70
2 Instruction Sheets

Primary Insulation O.D. Typical Creepage Approximate Installed

Order No. Jacket O.D. Range Typical Conductor Size Range
Range Distance Length
7673-S-8(R) 1.30”–2.36” 1.60”–2.85” 1/0 AWG–350 kcmil 79” (200 cm) 39”–41” (102–107 cm)
(33,0–60,0mm) (40,6–72,4mm) (50–175 mm²)
7673-S-8(S) 2.01”–2.87” 2.25”–3.45” 350–1500 kcmil 82” (208 cm) 40”–42” (102–107 cm)
(51,1–72,9 mm) (57,2–87,6 mm) (175–725 mm²)
7673-S-8 2.79”–3.45” 3.00”–4.25” 1500–3000 kcmil 82” (208 cm) 40”–42” (102–107 cm)
(70,9–87,6 mm) (76,2–108,0 mm) (800–1500 mm²)
7673-S-10(R) 1.30”–2.36” 1.60”–2.85” 1/0 AWG–350 kcmil 93” (238 cm) 47”–49” (119–124 cm)
(33,0–60,0 mm) (40,6–72,4 mm) (50–175 mm²)
7673-S-10(S) 2.01”–2.87” 2.25”–3.45” 350–1500 kcmil 97” (248 cm) 48”–50” (122–127 cm)
(51,1–72,9 mm) (57,2–87,6 mm) (175–725 mm²)
7673-S-10 2.79”–3.45” 3.00”–4.25” 1500–3000 kcmil 97” (248 cm) 48”–50” (122–127 cm)
(70,9–87,6 mm) (76,2–108,0 mm) (800–1500 mm²)
7673-S-INV-10(R) 1.30”–2.36” 1.60”–2.85” 1/0 AWG–350 kcmil 93” (238 cm) 47”–49” (119–124 cm)
(33,0–60,0 mm) (40,6–72,4 mm) (50–175 mm²)
7673-S-INV-10(S) 2.01”–2.87” 2.25”–3.45” 350–1500 kcmil 97” (248 cm) 48”–50” (122–127 cm)
(51,1–72,9 mm) (57,2–87,6 mm) (175–725 mm²)
7673-S-INV-10 2.79”–3.45” 3.00”–4.25” 1500–3000 kcmil 97” (248 cm) 48”–50” (122–127 cm)
(70,9–87,6 mm) (76,2–108,0 mm) (800–1500 mm²)

PHONE: 800-245-3573 www.3M.com/Electrical 327

IronwoodPremium_474115_Catalog-On-Demand9.QXD 6/16/2015 11:58 PM Page 328

Accessories for 69/72,5 kV

3M™ Cold Shrink QS-III Splice Kit 5488A Series for 69 kV

The 3M™ Cold Shrink QS-III Splice Kit 5488A is a 69 kV–class splice for joining jacketed concentric neutral (JCN), tape shield, longitudinally corrugated
(LC) shielded, tape-over-wire (TOW) or wire-over-tape (WOT) shielded power cables. It is a cold shrink design sized to fit Type MV–90 or type MV-105
cables with copper or aluminum conductor sizes ranging from 250 kcmil–2000 kcmil (120–1000 mm²). The cold shrink splice body is a one–piece molded
design made of specially formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice
manufactured is factory tested to provide reliability. The product numbers containing “XB” are for crossbond or shield break applications.
Kit Contents for 5488A Splice:
2 Silicone Rubber Splice Body 2 Roll Scotch® Semi-conducting Tape 13
2 Jacketing Tubes 2 Roll Scotch® Vinyl Electrical Tape Super 88
2 Shielding Sleeve 2 3M™ Cable Cleaning Pads CC-3
2 Pre-formed Braid Assembly (except JCN) 2 3M™ Copper Foil Tape Strips 1811, 15” long; (except JCN)
2 Constant Force Springs 2 Rolls 3M™ Armorcast Structural Material 4560, 3” x 15’
2 3M™ Red Compound P55/R Tubes (non-silicone grease) 2 Shear Bolt Connector
2 Roll 3M™ Scotch-Seal™ Mastic Tape 2229 2 Instruction Booklets
2 Rolls Scotch® Rubber Mastic Tape 2228
Additional Kit Contents for 5488A-JCN-XB and 5488A-Shielded-XB:
2 Silicone Rubber Tube Assembly
2 Roll, Scotch® Linerless Rubber Splicing Tape 130C
2 Roll, Scotch® Electrical Shielding Tape 24

Tape Shield, Longitudinally Corrugated,

Shielding Type Jacketed Concentric Neutral, Tape
Over Wire, Wire Over Tape
Indoor/Outdoor Outdoor
BIL Rating 350 kV
Voltage 69 kV
Certifications IEEE Std. 404 for 69 kV
High Voltage Joints and Terminations, 72,5–145 kV

Order No. UPC Conductor Size Cable Insulation O.D. Connector O.D. Case Qty
5488A-250-500 051128-56798 250–500 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.44” (62,0 mm) 1
5488A-750-1000 051128-56799 750–1000 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.76” (70,1 mm) 1
5488A-1250-1500 051128-56800 1250–1500 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.06” (77,7 mm) 1
5488A-1750-2000 051128-56801 1750–2000 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.25” (82,6 mm) 1
5488A-XB-JCN250-500 051128-56802 250–500 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.44” (62,0 mm) 1
5488A-XB-JCN750-1000 051128-56803 750–1000 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.76” (70,1 mm) 1
5488A-XB-JCN1250-1500 051128-56804 1250–1500 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.06” (77,7 mm) 1
5488A-XB-JCN1750-2000 051128-56805 1750–2000 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.25” (82,6 mm) 1
5488A-XB-SHIELDED-250-500 051128-57882 250–500 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.44” (62,0 mm) 1
5488A-XB-SHIELDED-750-1000 051128-57883 750–1000 kcmil 1.94”–3.08” (49,3–75,4 mm) 2.76” (70,1 mm) 1
5488A-XB-SHIELDED-1250-1500 051128-57884 1250–1500 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.06” (77,7 mm) 1
5488A-XB-SHIELDED-1750-2000 051128-57885 1750–2000 kcmil 1.94”–3.08” (49,3–75,4 mm) 3.25” (82,6 mm) 1

328 FAX: 800-245-0329

IronwoodPremium_474115_Catalog-On-Demand17.QXD 6/16/2015 11:58 PM Page 386

Preparation and Cleaning

3M™ Cable Cleaning System CC Series

3M™ Cable Cleaning System CC Series cleans cable insulation, metal, electrical and
mechanical parts. It can be used for PCB cleanup and as parts cleaners for degreasing.
CC-Dry contains three each 4” x 8” (102 x 203 mm) lintless non-woven pads packed in a bag.
These are used for drying the common citrus cable cleaner (CC series) off of cable installation
when preparing cable. The CC-2-Dry Kit contains a CC-2 Kit and three each dry lintless pads.

RoHS 2011/65/EU Yes

Order No. UPC Description Kit Contents Kits per Case

CC-2 054007-49563 Cable preparation kit (3) Solvent saturated cable cleaning pads; and 10
(1) Non-conductive grit abrasive cloth
CC-DRY 054007-43415 Dry wiping cloths (3) Unsaturated cable cleaning pads 10
CC-2-DRY 054007-43414 Dry cable preparation kit (3) Solvent saturated cable cleaning pads; 10
(3) Unsaturated cable cleaning pads; and
(1) Non-conductive grit abrasive cloth
CC-3 054007-49564 Cable cleaning pads (3) Solvent saturated cable cleaning pads 10

Scotch® Electricians’ Abrasive Roll A-3

Scotch® Electricians’ Abrasive Roll A-3 is a 120-grit, closed-coat aluminum oxide strip, which is nonconductive
and flexible. It is packaged in a dispenser-type box.

Abrasive Backing Type Cloth

Abrasive Backing Weight J Weight
Abrasive Mineral Type Aluminum Oxide
Cable Accessory Products

Order No. UPC Length Width Grade Product Form Rolls per Case
A-3 054007-11560 75’ (22,86 m) 1” (25,4 mm) 120 Roll 10

386 FAX: 800-245-0329