Control board setting and connections

detailed control board Layout

FORCE Adjustment (Advanced Users)

A terminal board is fitted in the lower part of the operator for the connection of the motor, of any
limit switch

Over Current Sensitivity

REF1 is Over current adjustment for the FAST speed.
ENGLISH

REF 1 REF 2
REF2 is Over current adjustment for the SLOW speed.
The Potentiometers REF1 & REF2 are factory base
set and should NOT be adjusted by the installer until
the installation dimensions are re checked and setup
cycle is completed.
Control Board Adjustments and Indicators Explained

.
L6 L7 L8 L9

L6
L6

L7

L8

L9

.
Beam Loop P.B 1 P.B 2 Light

Beam The GREEN LED is OFF in standby while gates are closed. It will be
ON during the closing cycle to indicate that the safety beam circuit is operatio
-nal. The factory link connecting BEAM and GND must be retained if a safety
beam is not used.
LOOP The GREEN LED will pulse on once when receiving contact indicating
that the signal was received.
P.B 1 The GREEN LED will pulse on once when receiving contact indicating
that the signal was received.
P.B 2 The GREEN LED will pulse on once when receiving contact indicating
that the double was received.
Light This GREEN LED will be ON during the opening operation of the gate(s).It will
stay ON while the gate(s) are open, and it will switch OFF within 10 seconds after the
gate(s) are closed.
ENGLISH

Program Button, use this button to start the

REMOTE
programming cycle

SETUP Remote control programming

 CH1 CH2 CH3

CH 1: Used for Double Gate opening /closing.

CH 2: Used for Single Gate opening /closing.
CH 3: Used for party mode to cancel the Auto Close cycle for one Cycle.

NOTE: If the LED is illuminated this indicates the channel is programmed to

one of the remote buttons. If the LED is OFF then this channel is not
programmed and it will not operate.

ON DIP

S9
12 3 45

S9
Automatic door closing selection
Auto Close select:

ON
OFF
1 1
Auto Close Time select:
5 Sec 30 Sec 90 Sec 180 Sec
ON

2 3 2 3 2 3 2 3
Second Motor Delay
Second Motor Delay (for double gates only)
DELAY ON DELAY OFF
ENGLISH

4 4

Second Motor Delay Time

2 Sec 5 Sec
ON
5 5
 Connecting The Gate Motor(s)

Connect the gate motor(s) to the motor output connector(s) located in the bottom left corner
of the control board as illustrated below.

M1 M2

RED RED

BLACK BLACK

MAXIMUM CABLE DISTANCE BETWEEN MOTOR AND CONTROL PANEL IS 6 MTRS

REVERSE MOTOR POLARITY FOR PUSH TO OPEN

M1 Motor Output Terminal:

Motor output for the Master (Leading) gate in a Double gate installation.

Motor output for a Single gate in a Single gate installation.

M2 Motor Output Terminal:

Motor output for Slave(Trailing) gate in a Double gate installation.

Not used in a single gate installation.

Connecting The Battery

The control panel is supplied with one batteries.

AT-
DC 1 DC 2 SOLAR+ -
BAT- BAT+

BLACK RED
ENGLISH

-
+ Connecting the polarity incorrectly
! will damage the control board and
VOID your warranty.
BATTE
RY 1

-
+

BATTE
RY 2
 Connecting The Power Input

Please follow the instructions below carefully as this will be the Primary source of power
for the Control Board. Ensure that there are no loose strands before inserting the wire into the
connector to avoid shorting the Primary power source.
DO NOT Connect more than one

! power source at a time. This Will

damage the control board and
VOID your Warranty,

Solar Panel

+ -
DC 1 DC 2 SOLAR+ -
BAT- BAT+ BAT- BAT+

Internal AC Transformer

wered the
inate.
DC 1 DC 2 SOLAR+ -
BAT- BAT+
ENGLISH
Auto setup (Programming)

Before beginning this step you must first ensure that all your motor wiring connections are
connected correctly, there are no loose wire strands and all connection points are joined and
insulated correctly.

If you are using a limit switched motor ensure that the limit switches have been set correctly.

If this control panel was purchased in kit form you should not need to adjust the Force dials
as this would have been factory preset according to your motor type.

The purpose of the programming cycle is so that the gate control panel can learn its opening
and closing limits and learn its slowdown. If the control panel is not programmed it may run
inconsistently and may not reach its stopping points and/or slow down incorrectly.

Single Gate Users please disregard all references

to Slave/Trailing gate (M2).

1. Your gates should be in the closed position before beginning the programming cycle.
If they are not use the manual override to bring them to the closed position then release
the override.
2. Press and HOLD the f the FORCE dials on the top of the control panel.
3.When you hear the buzzer sound release the PROG Button.
4. Now press the button on your remote which activates your gates.
5. The control panel will now OPEN the Master/Leading gate (M1).
6. The control panel will now OPEN the Slave/Trailing gate (M2).
7. The control panel will now CLOSE the Slave/Trailing gate (M2).
8. The control panel will now CLOSE the Master/Leading gate (M1).
9. The buzzer will now sound indicating a successful programming.

IF THE BUZZER DOES NOT SOUND SEE THE SOLUTION BELOW

If the Auto Programming is not successful QUICK SETUP

the buzzer will not sound, you will notice that
Prog
the OPEN/CLOSE LED are illuminated.
Disconnect the motors(s) from the control panel
1 Press and HOLD.
immediately.
The reason for this is that the FORCE 1 is
2 Wait for the Buzzer sound.
set incorrectly you MUST re-adjust the FORCE
dial to its correct setting by turning Press any of the working
ENGLISH

anti-clockwise and attempting to program the 3 buttons on the remote.

control panel again.
4 Wait for the gate(s) to open
and close.

Buzzer sound means the

5 programming is completed.
Push Button Switches Connections

Once a PB input is triggered the LED indicator for

that input will illuminate momentarily.
P.B.1 P.B.2

P.B.1

P.B.2

GND
GND
M1 M2

GND
GND
PB2
PB1
Both gates
Single Push Button

Push button switch

Single 1 wire Link

Dual Push
with Isolation

Key Switch
Button Switch
Master gate
only

Connect to P.B.1 & Com For Single Gate opening

Connect to P.B.2 & Com For Double Gate opening

If a gate is opened as a single gate it MUST be closed as a single gate.

If a gate is opened as a double gate it MUST be closed as a double gate.

Connecting Safety Sensors

The PE sensors are a safety device used to prevent the gates closing on an object or obstacle that
breaks the beam between the transmitter and the receiver.

This is absolutely necessary if the Auto Close function is used.

The PE Sensor loop must be removed when installing the PE sensors.

! If PE Sensors are not installed the loop must be retained.

Connecting Photo Electric Sensor

BEAM

P.B.1
LOOP

P.B.2
GND

GND
GND

GND

12V GND
PE Beam

GND
+12V
GND

Receiver
Transmitter

_
- + +
NO
GND
NC
Connecting a Courtesy Lamp

Once the gate(s) begin opening the output and the

LED will switch on/illuminate until 10 seconds
after the gate(s) are closed.

Light

LAMP
BEAM

P.B.1
LOOP

P.B.2
GND

GND
GND

GND
- +

Connecting an Antenna for extended range

ANT GND

Inner core of the antenna cable to ANT

on the control board.

Connecting an Antenna for extended range

If this control panel was purchased in a kit the Remotes have already been programed for there primary
purpose only (gate opening).

CH 1 Double Gate Opening

CH 2 Single Gate Opening
CH 3 Party Mode (Cancel Auto Close for one cycle)
 Programming

1. Press the LEARN CH button for the channel group you wish to
program.
2. Cycle to the desired channel by pressing the LEARN CH button.
(The control panel indicates which channel you are on flashing the
channel
3. Press the desired button on the remote you wish to use for the
channel. Repeat the above process for any additional remote
Deleting

1. PRESS AND HOLD the LEARN CH button for the

channel group you wish to delete until the channel CH 1 CH 2 CH 3

groups LEDs begin flashing simultaneously. REMOTE

2. Release the LEARN CH button and wait for the
LEDs to stop flashing.
3. If the LEDs Simultaneously flashed 3 times then
STUP
stopped you have successfully deleted the remote.

Troubleshooting

Problems Solution
* The control panel is NOT * Try reprogramming the
responding to a remote control remote to the control panel.

* The gate(s) are open but will * Check the LED on the remote control
not close * Check the Power input from the batteries
* Check that the PE Sensor is aligned if in use
* The output voltage for * Check the accessories fuse
the accessories is not working and replace if necessary
* The gate(s) not reaching the end * Turn the FORCE 1 trimmer
of opening/closing distance fractionally clockwise

* No slow down * Re program the control panel

* The gate(s) are opening instead * Check the polarity of motor (s) wires.
of closing and closing instead of opening
* Check your remote
* The gates do not respond at all
* Reprogram the remote
ENGLISH

* Control Panel will not begin * Power off for 10 seconds

the programming cycle and then back on to restart the system
* Only one gate is opening * Check your limit switch settings are correct

* Restart the system and turn

* Control panel not timing out
down the FORCE 1 setting then reprogram