Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

1078-01 3

Download as pdf or txt
Download as pdf or txt
You are on page 1of 54

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2017

& ANSI/NCSL Z540-1-1994

TRESCAL, INC.
7350 North Teutonia Avenue
Milwaukee, WI 53209
Nathan Thrasher Phone: 414 351 7420

CALIBRATION

Valid To: May 31, 2025 Certificate Number: 1078.01

In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this
laboratory to perform the following calibrations1, 15:

I. Acoustical Quantities

Parameter/Equipment Range CMC2, 8, 13 (±) Comments

Sound Pressure Level3

Sound Level Calibrators (85 to 140) dB 0.20 dB + 0.032 % Piston phone,


125 Hz to 4 kHz transducer

Sound Level Meters (94 & 114) dB 0.4 dB Sound level calibrator
250 Hz, 1 kHz

II. Chemical

Parameter/Equipment Range CMC2 (±) Comments

Conductivity Meters (1 to 10) µS/cm 0.34 µS/cm Conductivity


(50 to 100) µS/cm 0.96 µS/cm solutions
(1000 to 1413) µS/cm 5.5 µS/cm
(5 to 100) mS/cm 750 µS/cm
(150 to 200) mS/cm 1.5 mS/cm

pH Meters3 4 pH 0.012 pH Standard buffers


7 pH 0.015 pH
10 pH 0.015 pH

(A2LA Cert. No. 1078.01) 11/21/2023 Page 1 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Refractometers3 (0 to 100) % Brix 0.2 % + 0.6R Standard solutions

III. Dimensional

Parameter/Equipment Range CMC2, 4 (±) Comments

Angle Blocks Up to 60° (0.36 + 1.1Ө/20) arcsec Sine bar, gage blocks,
gage amp & probe,
where Ө = angle

Angle Plates3 Up to 48 in 65 µin or (12 µin/in + 30 Gage amp. probe,


µin), whichever is indi-square & test
greater indicator

Articulating Arm3 (CMM) – ASME B89.4.22-2004

Single Point Articulation (2 to 10.5) ft Rsys

Effective Diameter 1 in (25.4 mm) 16 µin + Rsys Rsys is the std. dev. of
repeated UUT test
Volumetric Up to 76 in (3.7L + 14) µin + Rsys results during each
test parameter
Scanner Head 1 in (25.4 mm) 34 µin + Rsys

Bench Center –

Center Parallelism Up to 24 in (68 + 4L) µin Gage amp w/ probe

Base Flatness & Base Up to 24 in (62 + 2.5L) µin


Parallelism

Bore Gages3 Up to 12 in 21 µin/in + 0.6R SIP302M


(Whichever is Greater)

(A2LA Cert. No. 1078.01) 11/21/2023 Page 2 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Box Parallels –

Parallelism 5 in × 10 in × 10 in 28 µin Gage amp w/probe,


cylindrical square
Squareness 5 in × 10 in × 10 in 12 µin/in + 38 µin

Calipers3 (Including Intertest,


Oditest, Snap Jaw & Other
OD Calipers) –

Resolution 0.0001 in Up to 2 in 78 µin Gage blocks


(2 to 12) in 70 µin + 4 µin/in

Resolution 0.0005 in Up to 24 in 450 µin


(24 to 60) in 340 µin + 3.7 µin/in

Resolution 0.001 in Up to 30 in 840 µin


(30 to 100) in 700 µin + 3.4 µin/in

Chamfer Gages/Hole Gages3 Up to 12 in 20 µin + 0.6R Cylindrical rings

Clinometers & Up to 360° 0.18 arcseconds + 37 Sine bar/gage blocks


Inclinometers, & Electronic parts in 106
Levels

CMMs – Imaging (Video XY Diagonal Up to ISO 10360-7


CMMs/Vision Systems)3 36.5 in (Unidirectional)

Length Measurements

EUX, EUY, EUXY Up to 24 in (23 + 2.9L) µin Glass scales

EUV Up to 2 in (15 + 2.9L) µin Glass scales

EZ Up to 8 in (Z-axis) (41 + 3.2L) µin Gage blocks

Squareness – ESQ Up to 8 in (Z-axis) (19 + 130L) µin Ball bar

Probing Performance Diameter


Measured:
PF2D, PFV2D (0.012 to 0.12) in 16 µin Test circles
(0.12 to 0.4) in. 25 µin

(A2LA Cert. No. 1078.01) 11/21/2023 Page 3 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

CMMs3 –

Length Error (EL) Up to 52 in 40 µin + 5.2 min/in ASME


B89.4.1.10360.2, ISO
Repeatability Range (R0) Up to 52 in 22 µin + 3 µin/in 10360-2

Coating Thickness 25 µin to 0.5 in 19 µin + 82 µin/in ULM


Shims/Precision Shims

Concentricity Gage N/A 130 µin + 8 μin/in Indicator, bench center

Cylindrical Plugs3 Up to 4 in 4 µin + 5 µin/in ULM, gage blocks


(4 to 20) in 4 µin + 5.4 µin/in

Cylindrical Rings3 (0.1 to 4) in 4 µin + 5 µin/in ULM, gage blocks


(4 to 8.5) in 4 µin + 5.4 µin/in
(8.5 to 18) in 5.2 µin + 5.5 µin/in
(18 to 36) in 50 µin + 3 µin/in

External Spline Gages3 –

Measurement Over Pins Up to 8 in (170 + 28D) µin ULM

Circular Tooth Thickness Up to 8 in (110 + 16L) µin Vision system

Major Diameter Up to 8 in (28 + 12D) µin ULM

Fixed Gaging – Screw Pitch Up to 30 in (110 + 16L) µin Optical comparator,


Gages, Drill Gages, Taper (Length vision system, hand
Gages, Center Gages, Sheet Measures) tools, hand gages
& Wire Gages, Angle
Gages, Radius Gage, Up to 2 in 110 µin CMM
Functional Gages (2 to 40) in (110 + 5.5L) µin

Up to 360° 54” Vision system

(A2LA Cert. No. 1078.01) 11/21/2023 Page 4 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Gage Amplifier &


Probe(s)3

Single Probe Up to 0.025 in 8.9 µin Gage blocks

Dual Probe Up to 0.002 in 2.1 µin

Gage Balls Up to 4 in (32 + 1.5D) µin Universal length


machine (ULM)

Gage Blocks Up to 4 in (3.1 + 3.2L) µin Gage blocks &


(4 to 20) in (3.3 + 3.2L) µin comparator

Height Gage3 Up to 20 in (7 + 4.6H) µin Gage blocks, by


request

Up to 52 in (7.7 + 6.2H) µin Reference stack, SOP

Height Measures3 Up to 0.0005 in 13 µin Heidenhain Certo


(0.0005 to 2) in (16 + 2.6H) µin

(0 to 24) in (160 + 5.4H) µin Trimos Vertical 3

Indicators3 – Dial & Test, Up to 4 in 35 µin or 0.6R Indicator calibrator


LVDTs (Whichever is Greater)

Indicator Calibrator3 Up to 4 in 12 µin + 0.6R Gage blocks, amp


w/probe

Laser Distance Meters Up to 6.1 m 4.6 µm/m + 120 µm ULM

(A2LA Cert. No. 1078.01) 11/21/2023 Page 5 of 53


Parameter/Equipment Range CMC2, 4, 8 (±) Comments

Length & Thickness


Standards, Feeler Gages3 –

Steel Up to 4 in 4 µin + 5 µin/in ULM, gage blocks


(4 to 20) in 4 µin + 5.4 µin/in
(20 to 120) in 3.7 µin/in + 14 µin

Field Calibration Up to 16 in 5 µin + 14 µin/in + 4 µin/in/°C ULM, gage blocks,


Relative to 20/°C

Levels (Spirit, Bubble, Up to 96 in 5.1 arcseconds + (37 x 10-6) Surface plate & gage
Machinist)3 blocks

Linear Measurement of Up to 20 ft 1.5 μin/in + 0.58 μin Laser


Machine Tools Scales3

Linear Scales/Reticles &


Stage Micrometers –

2D Up to 12 in (110 + 16L) µin Vision system

1D Up to 30 in 14µin + 1.5 µin/in Gitterperioden


interferometer

Micrometers3 –

Inside Up to 294 in 12 µin + 7 µin /in + 0.2R ULM, gage blocks or


Depth Up to 12 in 18 µin/in + 0.64R rings
Tri-Bores Up to 11 in 18 µin/in + 0.7R
Outside Up to 42 in 18 µin/in + 0.64R
Groove Up to 4 in 18 µin/in + 0.64R
Bench Up to 42 in 18 µin/in + 0.64R
Thread (Screw, Thread, Up to 4 in 18 µin/in + 0.64R
Pitch, Point)

Microscopes3 –

Reticule Up to 25 mm 23 µm Stage micrometer


Magnification Up to 1000x 2.4 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 6 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Optical Comparator3 –

Linear Up to 12 in 0.0002 in Glass scale

Angle (0 to 360)° 2’ Protractor

Magnification 10x, 20x, 50x, 0.000 12 in Calibration sphere


62.5x, 100x, 200x

Optical Flats –

Flatness Up to 8 in 3.4 µin Reference flat &


monochromatic light
source

Parallelism11 Up to 1.5 in 3.1 µin Gage block


Diameter & 1 in comparator
Thickness

Parallels3 –

Parallelism Up to 72 in 1 µin/in + 20 µin Gage amp w/ probe

Pitch Micrometer Standards –

Length Up to 12 in (22 + 6L) µin UMM

Angle Up to 60° 54” Vision system

Precision Diameter Tapes Up to 38 in 1.3 µin/in + 280 µin Setting discs, ULM
(38 to 54) in 7.5 µin/in + 250 µin
(54 to 780) in 1.4 µin/in + 430 µin

Profilometers3 (15 to 150) µin Ra 2.8 µin Roughness specimen

Protractor – Digital & (0 to 180)° 0.0053° (19 arcsec) Sine bar & gage
Mechanical3 blocks

Riser Blocks & Stands Up to 24 in 2 µin/in + 23 µin Gage amplifier w/


probe

(A2LA Cert. No. 1078.01) 11/21/2023 Page 7 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Roundness Testers3 –

Coning Error Up to 16 in 11 µin Test ball & riser


cylinder

Axial Error Up to 16 in 11 µin Test ball

Radial Accuracy Up to 16 in 11 µin Test ball

Z-Axis Straightness (0.1 to 12) in (14 + 12H) µin Cylindrical square; in


the CMC

Sine Plates/Bars3 –

Flatness/Parallelism & Up to 20 in 53 µin Gage amp w/ probe,


Parallelism Cylinder to angle blocks & gage
Base blocks

Angle Calibration (0 to 90)° 0.000 45° (1.6 arcsec,


Center of Rolls 16 µin/in)

Up to 20 in 17 µin/in (1.8 arcsec)

Sand Sieves 20 µm to 125 mm (3.2 + 6.9L) µm ASTM E11, vision


system

Snap Gages3 –

Parallelism Up to 20 in 97 µin Box parallel with gage


amp & probe
Linear Accuracy Up to 20 in 1 µin/in + 49 µin

Sphericity Up to 4 in 17 µin Spindle less sphericity


fixture

Squares3 –

Master Squares (Class Up to 48 in 51 µin or (7 µin/in + 21 µin), Indi-square & test


A Grade) (Whichever is Greater) indicator, gage amp &
probe, gage locks
Granite, Steel, Up to 48 in 65 µin or (12 µin/in + 30
Cylindrical µin), (Whichever is Greater)

(A2LA Cert. No. 1078.01) 11/21/2023 Page 8 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Straightness & Up to 72 in 1 µin/in + 19 µin Gage amplifier w/


Straight Edges3 probe

Step Gages, Step Bars, Up to 50 in (9.7 + 3H) µin Gage amp & probe,
Reference Stacks gage blocks

Surface Plates3 –

Flatness 18 in x 24 in to 8√D µin Electronic levels


72 in x 144 in

Repeatability Up to 72 in x 144 in 34 µin Repeat-o-meter

Surface Roughness3 (15 to 150) µin (Ra, 3.4 µin Verification of


Rz, Rt, Rp) specimens per ASME
B46.1

Tape Measures, Rulers3 Up to 10 ft 1200 µin + 2.1 µin/in ULM


(10 to 300) ft 220 µin + 6.8 µin/in

Tapered Plugs3 –

Simple Pitch Diameter Up to 18 in (100 + 8D) µin Thread wires/UMM

Notch Height Up to 18 in 13 µin/in + 94 µin Height measuring


machine

Tapered Rings3 –

Taper Up to 18 in 400 µin NPT master plug,


ULM

Standoff & Thickness Up to 18 in 120 µin NPT master plug &


height measuring
Functional Diameter Up to 2 in (300 + 8D) µin machine

(A2LA Cert. No. 1078.01) 11/21/2023 Page 9 of 53


Parameter/Equipment Range CMC2, 4 (±) Comments

Thread Plugs3 –

Simple Pitch Diameter Up to 20 in 82 µin + 6.8 µin/in 3-wire method

Major Diameter Up to 4 in 4 µin + 5 µin/in ULM, gage blocks


(4 to 8.5) in 4 µin + 5.4 µin/in
(8.5 to 20) in 5.2 µin + 5.5 µin/in

Thread Rings3 –

Simple Pitch Diameter Up to 18 in (140 + 9D) µin ULM


Minor Diameter Up to 2 in (70 + 13D) µin

Functional Diameter Up to 18 in (100 + 8D) µin w/ set plug

Thread Wires Up to 0.5 in (8.5 + 7D) µin ULM, gage blocks

Universal Length Up to 4 in 1.5 µin + 1.2 µin/in Gage blocks, force


Machines3 (ULMs) (4 to 24) in 1.3 µin + 1.8 µin/in gage, optical flat,
monochromatic light
source

V-Blocks –

Parallelism Side 8 in × 8 in × 8 in 28 µin Gage amplifier w/


probe

V Parallelism 8 in × 8 in × 8 in 1 µin/in + 28 µin Cylindrical square

Squareness 8 in × 8 in × 8 in 9.7 µin/in + 48 µin Cylindrical plug

Wire Crimpers3 –

Crimp Height Up to 00 Gauge 0.0024 in Micrometer

Crimping Chamber Up to 00 Gauge (10 + 19D) µin Pin

Ratchet Inspection Up to 00 Gauge 120 µin Feeler gage

(A2LA Cert. No. 1078.01) 11/21/2023 Page 10 of 53


IV. Electrical – DC/Low Frequency

Parameter/Range Frequency CMC2, 7 (±) Comments

AC Current – Generate Max frequency up to


& Measure3 3 mA is 30 kHz.
Fluke 5790A,
10 µA to 20 A 10 Hz to 50 kHz3 See Table IV.a 5700A/EP, A40s,
standard resistors

(20 to 70) A 10 Hz 85 µA/A Fluke 52120A,


(20 to 100) A 55 Hz 0.013 % A40B-100, DMM
300 Hz 0.012 %
1 kHz 0.012 %
5 kHz 0.036 %
(20 to 80) A 6 kHz 0.039 %
(20 to 50) A 10 kHz 0.092 %

Measure Only3

(100 to 1000) A 60 Hz 0.5 % Current clamp-on


meter
Generate Only–Turn
Amps3

(20 to 120) A (50 to 400) Hz 0.055 % + 0.6 A Fluke 55120A w/


(120 to 6000) A 0.80 % - 1.6 A 52120-3k & 52120-
6k coils
(20 to 120) A 1000 Hz 0.24 % + 0.24 A

AC Current – 50 Turn
Coils

Effective Current 25 Turn Amps, 50 Hz,400 Hz 0.11 % of ratio Comparison to


Transfer Ratio 500 Turn Amps, 50 Hz, 400 Hz 0.12 % of ratio standard coil
800 Turn Amps, 400 Hz 0.14 % of ratio
1000 Turn Amps, 50 Hz 0.14 % of ratio

(A2LA Cert. No. 1078.01) 11/21/2023 Page 11 of 53


TABLE IV.a AC Current Generate / Measure3 – CMCs

Current Range 10 Hz 20 Hz 40 Hz
(10 to 300) µA 170 µA/A + 0.03 nA 67 µA/A + 0.03 nA 37 µA/A + 0.03 nA
300 µA to 3 mA 170 µA/A + 0.3 nA 60 µA/A + 0.3 nA 29 µA/A + 0.3 nA
(3 to 10) mA 170 µA/A + 1 nA 69 µA/A + 1 nA 37 µA/A + 1 nA
(10 to 20) mA 170 µA/A + 2 nA 69 µA/A + 2 nA 37 µA/A + 2 nA
(20 to 30) mA 170 µA/A + 3 nA 69 µA/A + 3 nA 37 µA/A + 3 nA
(30 to 50) mA 170 µA/A + 5 nA 69 µA/A + 5 nA 37 µA/A + 5 nA
(50 to 100) mA 170 µA/A + 60 nA 69 µA/A + 60 nA 37 µA/A + 60 nA
(100 to 200) mA 170 µA/A + 120 nA 72 µA/A + 120 nA 37 µA/A + 120 nA
(200 to 300) mA 170 µA/A + 180 nA 72 µA/A + 180 nA 37 µA/A + 180 nA
(300 to 500) mA 170 µA/A + 300 nA 72 µA/A + 300 nA 37 µA/A + 300 nA
500 mA to 1 A 170 µA/A + 6 µA 72 µA/A + 6 µA 41 µA/A + 6 µA
(1 to 2) A 170 µA/A + 12 µA 75 µA/A + 12 µA 42 µA/A + 12 µA
(2 to 3) A 180 µA/A + 18 µA 81 µA/A + 18 µA 58 µA/A + 18 µA
(3 to 5) A 190 µA/A + 30 µA 85 µA/A + 30 µA 58 µA/A + 30 µA
(5 to 10) A 190 µA/A + 60 µA 100 µA/A + 60 µA 73 µA/A + 60 µA
(10 to 20) A 220 µA/A + 12 µA 130 µA/A + 12 µA 86 µA/A + 12 µA

Current Range 400 Hz 1 kHz 5 kHz


(10 to 300) µA 37 µA/A + 0.03 nA 37 µA/A + 0.03 nA 46 µA/A + 0.03 nA
300 µA to 3 mA 29 µA/A + 0.3 nA 30 µA/A + 0.3 nA 30 µA/A + 0.3 nA
(3 to 10) mA 35 µA/A + 1 nA 35 µA/A + 1 nA 36 µA/A + 1 nA
(10 to 20) mA 35 µA/A + 2 nA 35 µA/A + 2 nA 36 µA/A + 2 nA
(20 to 30) mA 35 µA/A + 3 nA 35 µA/A + 3 nA 36 µA/A + 3 nA
(30 to 50) mA 35 µA/A + 5 nA 35 µA/A + 5 nA 36 µA/A + 5 nA
(50 to 100) mA 35 µA/A + 60 nA 35 µA/A + 60 nA 36 µA/A + 60 nA
(100 to 200) mA 35 µA/A + 120 nA 35 µA/A + 120 nA 36 µA/A + 120 nA
(200 to 300) mA 35 µA/A + 180 nA 35 µA/A + 180 nA 36 µA/A + 180 nA
(300 to 500) mA 35 µA/A + 300 nA 35 µA/A + 300 nA 36 µA/A + 300 nA
500 mA to 1 A 39 µA/A + 6 µA 39 µA/A + 6 µA 40 µA/A + 6 µA
(1 to 2) A 40 µA/A + 12 µA 39 µA/A + 12 µA 40 µA/A + 12 µA
(2 to 3) A 56 µA/A + 18 µA 56 µA/A + 18 µA 56 µA/A + 18 µA
(3 to 5) A 56 µA/A + 30 µA 56 µA/A + 30 µA 56 µA/A + 30 µA
(5 to 10) A 72 µA/A + 60 µA 71 µA/A + 60 µA 72 µA/A + 60 µA
(10 to 20) A 85 µA/A + 12 µA 84 µA/A + 12 µA 85 µA/A + 12 µA

(A2LA Cert. No. 1078.01) 11/21/2023 Page 12 of 53


TABLE IV.a (cont) AC Current Generate / Measure3 - CMCs

Current Range 10 kHz 20 kHz 50 kHz


(10 to 300) µA 46 µA/A + 0.03 nA 62 µA/A + 0.03 nA 79 µA/A + 0.03 nA
300 µA to 3 mA 30 µA/A + 0.3 nA 45 µA/A + 0.3 nA 48 µA/A + 0.3 nA
(3 to 10) mA 36 µA/A + 1 nA 36 µA/A + 1 nA 60 µA/A + 1 nA
(10 to 20) mA 36 µA/A + 2 nA 36 µA/A + 2 nA 63 µA/A + 2 nA
(20 to 30) mA 36 µA/A + 3 nA 36 µA/A + 3 nA 63 µA/A + 3 nA
(30 to 50) mA 36 µA/A + 5 nA 36 µA/A + 5 nA 63 µA/A + 5 nA
(50 to 100) mA 36 µA/A + 60 nA 39 µA/A + 60 nA 68 µA/A + 60 nA
(100 to 200) mA 36 µA/A + 120 nA 39 µA/A + 120 nA 68 µA/A + 120 nA
(200 to 300) mA 36 µA/A + 180 nA 39 µA/A + 180 nA 72 µA/A + 180 nA
(300 to 500) mA 36 µA/A + 300 nA 39 µA/A + 300 nA 72 µA/A + 300 nA
500 mA to 1 A 40 µA/A + 6 µA 52 µA/A + 6 µA 110 µA/A + 6 µA
(1 to 2) A 40 µA/A + 12 µA 52 µA/A + 12 µA 110 µA/A + 12 µA
(2 to 3) A 56 µA/A + 18 µA 61 µA/A + 18 µA 120 µA/A + 18 µA
(3 to 5) A 56 µA/A + 30 µA 70 µA/A + 30 µA 160 µA/A + 30 µA
(5 to 10) A 72 µA/A + 60 µA 89 µA/A + 60 µA 130 µA/A + 60 µA
(10 to 20) A 85 µA/A + 12 µA 110 µA/A + 12 µA 150 µA/A + 12 µA

Parameter/Range Frequency CMC2, 6, 8 (±) Comments

AC Power3 – Generate
PF = 1
(29 to 330) µA (10 to 20) Hz, 0.19 % Fluke 5520A
(0.33 to 3.3) mA 1 mV to 33 V 0.17 %
3.3 mA to 3.3 A 0.15 %
(29 to 330) µA (20 to 45) Hz, 0.15 %
(0.33 to 3.3) mA 1 mV to 33 V 0.11 %
(3.3 to 330) mA 0.080 %
330 mA to 3 A 0.15 %
(29 to 330) µA (45 to 100) Hz, 0.13 %
(0.33 to 3.3) mA 1 mV to 1020 V 0.088 %
(3.3 to 330) mA 0.041 %
330 mA to 1.1 A 0.052 %
(1.1 to 3) A 0.054 %
(3 to 11) A 0.065 %
(11 to 20.5) A 0.12 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 13 of 53


Parameter/Range Frequency CMC2, 6, 8 (±) Comments

AC Power3 – Generate
PF = 1 (cont)

(29 to 330) µA 100 Hz to 1 kHz, 0.13 % Fluke 5520A


(0.33 to 3.3) mA 1 mV to 1020 V 0.088 %
(3.3 to 33) mA 0.041 %
(33 to 330) mA 0.041 %
330 mA to 1.1 A 0.052 %
(1.1 to 3) A 0.054 %
(3 to 11) A 0.095 %
(3 to 20.5) A 0.14 %

(29 to 330) µA (1 to 5) kHz, 0.28 %


(0.33 to 3.3) mA 1 mV to 1020 V 0.17 %
(3.3 to 33) mA 0.070 %
(33 to 330) mA 0.092 %
330 mA to 1.1 A 0.54 %

(1.1 to 3) A (1 to 5) kHz, 0.26 %


(3 to 11) A 1 mV to 1020 V 2.4 %
(11 to 20.5) A 2.4 %

(29 to 330) µA (5 to 10) kHz, 0.67 %


(0.33 to 3.3) mA 1 mV to 1020 V 0.40 %
(3.3 to 33) mA 0.17 %
(33 to 330) mA 0.18 %
330 mA to 1.1 A 2.3 %
(1.1 to 3) A 2.1 %

(29 to 330) µA (10 to 30) kHz, 1.3 %


(0.33 to 3.3) mA 1 mV to 330 V 0.79 %
(3.3 to 330) mA 0.32 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 14 of 53


Parameter/Range Frequency CMC2, 7 (±) Comments

AC Voltage – Measure
& Generate3

(0.6 to 2.2) mV (10 to 20) Hz 0.14 % + 1.1 µV Fluke 5790A, 5720A


(20 to 40) Hz 0.062 % + 1.1 µV
40 Hz to 20 kHz 0.040 % + 1.1 µV
(20 to 50) kHz 0.067 % + 1.6 µV
(50 to 100) kHz 0.097 % + 2.0 µV
(100 to 300) kHz 0.19 % + 3.2 µV
(300 to 500) kHz 0.19 % + 6.3 µV
500 kHz to 1 MHz 0.31 % + 6.3 µV

(2.2 to 7) mV (10 to 20) Hz 0.068 % + 1.1 µV


(20 to 40) Hz 0.032 % + 1.1 µV
40 Hz to 20 kHz 0.021 % + 1.1 µV
(20 to 50) kHz 0.034 % + 1.6 µV
(50 to 100) kHz 0.049 % + 2.0 µV
(100 to 300) kHz 0.096 % + 3.2 µV
(300 to 500) kHz 0.11 % + 6.3 µV
500 kHz to 1 MHz 0.19 % + 6.3 µV

(7 to 22) mV (10 to 20) Hz 0.024 % + 1.1 µV


(20 to 40) Hz 0.016 % + 1.1 µV
40 Hz to 20 kHz 0.0096 % + 1.1 µV
(20 to 50) kHz 0.018 % + 1.6 µV
(50 to 100) kHz 0.026 % + 2.0 µV
(100 to 300) kHz 0.066 % + 3.2 µV
(300 to 500) kHz 0.074 % + 6.3 µV
500 kHz to 1 MHz 0.14 % + 6.3 µV

(22 to 70) mV (10 to 20) Hz 0.022 % + 1.2 µV


(20 to 40) Hz 0.012 % + 1.2 µV
40 Hz to 20 kHz 0.0071 % + 1.2 µV
(20 to 50) kHz 0.012 % + 1.6 µV
(50 to 100) kHz 0.025 % + 2.0 µV
(100 to 300) kHz 0.048 % + 3.2 µV
(300 to 500) kHz 0.063 % + 6.3 µV
500 kHz to 1 MHz 0.096 % + 6.3 µV

(70 to 220) mV (10 to 20) Hz 0.017 % + 1.2 µV


(20 to 40) Hz 0.0076 % + 1.2 µV
40 Hz to 20 kHz 0.0037 % + 1.2 µV
(20 to 50) kHz 0.0058 % + 1.6 µV
(50 to 100) kHz 0.013 % + 2.0 µV
(100 to 300) kHz 0.022 % + 3.2 µV
(300 to 500) kHz 0.031 % + 6.3 µV
500 kHz to 1 MHz 0.079 % + 6.3 µV

(A2LA Cert. No. 1078.01) 11/21/2023 Page 15 of 53


Parameter/Range Frequency CMC2, 7, 8 (±) Comments

AC Voltage – Measure
& Generate3 (cont)

(220 to 700) mV (10 to 20) Hz 0.017 % + 1.2 µV Fluke 5790A, 5720A


(20 to 40) Hz 0.0061 % + 1.2 µV
40 Hz to 20 kHz 0.0029 % + 1.2 µV
(20 to 50) kHz 0.0046 % + 1.6 µV
(50 to 100) kHz 0.0063 % + 2.0 µV
(100 to 300) kHz 0.017 % + 4.3 µV
(300 to 500) kHz 0.025 % + 6.3 µV
500 kHz to 1 MHz 0.074 % + 6.3 µV

(0.7 to 2.2) V (10 to 20) Hz 0.018 %


(20 to 40) Hz 0.0061 %
40 Hz to 20 kHz 0.0022 %
(20 to 50) kHz 0.004 %
(50 to 100) kHz 0.0057 %
(100 to 300) kHz 0.015 %
(300 to 500) kHz 0.023 %
500 kHz to 1 MHz 0.074 %

(2.2 to 7) V (10 to 20) Hz 0.016 %


(20 to 40) Hz 0.0054 %
40 Hz to 20 kHz 0.0024 %
(20 to 50) kHz 0.0041 %
(50 to 100) kHz 0.0065 %
(100 to 300) kHz 0.018 %
(300 to 500) kHz 0.035 %
500 kHz to 1 MHz 0.097 %

(7 to 22) V (10 to 20) Hz 0.016 %


(20 to 40) Hz 0.0057 %
40 Hz to 20 kHz 0.0030 %
(20 to 50) kHz 0.0039 %
(50 to 100) kHz 0.0065 %
(100 to 300) kHz 0.018 %
(300 to 500) kHz 0.033 %
500 kHz to 1 MHz 0.097 %

(22 to 70) V (10 to 20) Hz 0.016 %


(20 to 40) Hz 0.0058 %
40 Hz to 20 kHz 0.0034 %
(20 to 50) kHz 0.0050 %
(50 to 100) kHz 0.0075 %
(100 to 300) kHz 0.016 %
(300 to 500) kHz 0.032 %
500 kHz to 1 MHz 0.09 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 16 of 53


Parameter/Range Frequency CMC2, 7, 14 (±) Comments

AC Voltage – Measure &


Generate3 (cont)

(70 to 220) V* (10 to 20) Hz 0.016 % Fluke 5790A, 5720A


(20 to 40) Hz 0.0058 % *Subject to 2.2 x 107
40 Hz to 20 kHz 0.0034 % V-Hz limitation
(20 to 50) kHz 0.0056 %
(50 to 100) kHz 0.0080 %
(100 to 300) kHz 0.017 %
(300 to 500) kHz 0.039 %

(220 to 700) V (10 to 20) Hz 0.016 % Fluke 5790A, 5720A,


(20 to 40) Hz 0.0080 % 5725A
40 Hz to 20 kHz 0.0038 %
(20 to 50) kHz 0.011 %
(50 to 100) kHz 0.040 %

(700 to 1000) V** (10 to 20) Hz 0.016 % ** Measure only


(20 to 40) Hz 0.0080 %
40 Hz to 20 kHz 0.0036 %
(20 to 50) kHz 0.011 %
(50 to 100) kHz 0.040 %

AC High Voltage –
Measure3

(1 to 5) kV (50 to 60) Hz 0.2 % + 1 V Vitrek 4700A


(5 to 35) kV 0.4 % + 65 V
(35 to 75) kV 0.4 % + 49 V

AC High Voltage –
Generate3

(1 to 5) kV 60 Hz 0.24 % + 1 V Assoc. res. 3565D

(A2LA Cert. No. 1078.01) 11/21/2023 Page 17 of 53


Parameter/Range Frequency CMC2, 5 (±) Comments

AC Voltage –
Measure3
≤ 2 MHz
(0 to 10) mV (1 to 40) Hz 0.023 % + 2 µV Agilent/HP 3458A
40 Hz to 1 kHz 0.018 % + 0.74 µV
(1 to 20) kHz 0.026 % + 0.74 µV
(20 to 50) kHz 0.069 % + 0.74 µV
(50 to 100) kHz 0.34 % + 0.74 µV
(100 to 300) kHz 2.7 % + 1.4 µV

(10 to 100) mV (1 to 40) Hz 0.033 % + 2.7 µV


40Hz to 1kHz 0.014 % + 1.4 µV
(1 to 20) kHz 0.019 % + 1.4 µV
(20 to 50) kHz 0.037 % + 1.4 µV
(50 to 100) kHz 0.067 % + 1.4 µV
(100 to 300) kHz 0.22 % + 6.7 µV
300 kHz to 1 MHz 0.68 % + 6.7 µV
(1 to 2) MHz 1.1 % + 6.7 µV

(0.1 to 1) V (1 to 40) Hz 0.0047 % + 27 µV


40 Hz to 1kHz 0.0047 % + 14 µV
(1 to 20) kHz 0.0094 % + 14 µV
(20 to 50) kHz 0.020 % + 14 µV
(50 to 100) kHz 0.054 % + 14 µV
(100 to 300) kHz 0.20 % + 67 µV
300 kHz to 1 MHz 0.67 % + 67 µV
(1 to 2) MHz 1.1 % + 67 µV

(1 to 10) V (1 to 40) Hz 0.0077 % + 0.27 mV


40 Hz to 1 kHz 0.0062 % + 0.14 mV
(1 to 20) kHz 0.0099 % + 0.14 mV
(20 to 50) kHz 0.021 % + 0.14 mV
(50 to 100) kHz 0.054 % + 0.14 mV
(100 to 300) kHz 0.21 % + 0.67 mV
300 kHz to 1 MHz 0.67 % + 0.67 mV
(1 to 2) MHz 1.1 % + 0.67 mV

(10 to 100) V (1 to 40) Hz 0.025 % + 2.7 mV


40 Hz to 1 kHz 0.016 % + 1.4 mV
(1 to 20) kHz 0.014 % + 1.4 mV
(20 to 50) kHz 0.025 % + 1.4 mV
(50 to 100) kHz 0.082 % + 1.4 mV
(100 to 300) kHz 0.27 % + 6.7 mV
300 kHz to 1 MHz 1.1 % + 6.7 mV
(100 to 700) V (1 to 40) Hz 0.033 % + 27 mV
40 Hz to 1 kHz 0.027 % + 14 mV
(1 to 20) kHz 0.041 % + 14 mV
(20 to 50) kHz 0.081 % + 14 mV
(50 to 100) kHz 0.21 % + 14 mV

(A2LA Cert. No. 1078.01) 11/21/2023 Page 18 of 53


Parameter/Range Frequency CMC2, 5, 7, 8, 14 (±) Comments

Capacitance – Measure3

1 pF 1 kHz 11 µF/F AH2500A


10 pF 13 µF/F
100 pF to 1 µF 14 µF/F

(0.7 to 110) mF DC 0.012 % 5700A w/ 3458A, charge


method

10 pF to 0.1 F 12 Hz to 2 MHz See Table IV.b Quad tech 1689M, 7600

Capacitance –
Generate3, Fixed Points

100 pF 100 Hz, 1 kHz 0.054 % Standard capacitors


0.001 µF 0.068 %
0.002 µF 0.048 %
(0.01, 0.02, 0.05) µF 0.055 %
(0.1, 0.5, 1) µF 0.055 %

Table IV.b: CMC (in %) for Capacitance Measured with 1689M & 7600 LCR Meter, Fixed Points

10 100 1 10 100 1 10 100 0.001 0.01 0.1


pF pF nF nF nF µF µF µF F F F
12 Hz 3.1 5 1.5 0.79 0.93 0.14 0.11 0.46 4.5
20 Hz 1.9 3 0.63 0.48 0.49 0.11 0.11 0.76
50 Hz 3.8 0.39 0.47 0.25 0.11 0.16 0.058 0.11 0.94
100 Hz 1.4 0.16 0.21 0.15 0.047 0.067 0.047 0.16 1.4
200 Hz 0.71 0.081 0.12 0.095 0.047 0.047 0.047 0.29 2.8
500 Hz 1.9 0.2 0.035 0.042 0.058 0.035 0.035 0.058 0.48 4.4
1 kHz 0.48 0.058 0.024 0.024 0.024 0.024 0.024 0.058 0.48 4.7
2 kHz 0.71 0.081 0.047 0.035 0.035 0.041 0.035 0.17 1.2
5 kHz 0.66 0.083 0.056 0.047 0.047 0.056 0.08 0.32 2.8
10 kHz 0.42 0.07 0.056 0.055 0.055 0.06 0.11 0.6
20 kHz 0.035 0.024 0.048 0.057 0.058 0.068 0.18 1.3
50 kHz 0.024 0.024 0.066 0.066 0.07 0.11 0.46 4.1
100 kHz 0.024 0.03 0.08 0.081 0.091 0.2 1.2
200 kHz 0.27 0.11 0.11 0.12 0.15 0.46 3.7
500 kHz 0.43 0.4 0.2 0.38 0.38 2.1
1 MHz 0.36 0.35 0.35 0.41 1.1
2 MHz 0.65 0.64 0.66 0.9 3.4

(A2LA Cert. No. 1078.01) 11/21/2023 Page 19 of 53


Parameter/Equipment Range CMC2, 5, 6, 8, 14 (±) Comments

DC Power3 – Generate

33 mV to 1020 V 330 µA to 330 mA 0.068 % Fluke 5520A


330 mA to 3 A 0.07 %
(3 to 20.5) A 0.12 %

DC Current3 –

Generate & Measure (0 to 100) nA 30 µA/A + 0.027 nA Agilent/HP


(0.1 to 1) µA 18 µA/A + 0.027 nA 3458A/HFL, current
(1 to 10) µA 16 µA/A + 0.067 nA source, standard
resistors/current shunts
(10 to 100) µA 5.2 µA/A + 0.01 nA
(0.1 to 1 mA 4.9 µA/A + 0.1 nA
(1 to 10) mA 5.1 µA/A + 1 nA
(10 to 100) mA 5.6 µA/A + 60 nA
(0.1 to 1) A 7.3 µA/A + 6 µA
(1 to 2) A 8.9 µA/A + 12 µA
(2 to 10) A 31 µA/A + 6 µA
(10 to 20) A 31 µA/A + 12 µA

(20 to 100) A 27 µA/A + 18 µA/°C


(100 to 300) A 0.011 % + 18 µA/°C
(300 to 1000) A 0.077 % + 18 µA/°C

Generate Only (20 to 100) A 0.09 % + 970 µA Fluke 52120A w/


Turn Amps (1000 to 3000) A 0.27 % + 470 mA 52120-3k & 52120-6k
(3000 to 6000) A 0.38 % + 340 mA coils

DC Voltage – Generate, 100 mV 0.82 μV/V Fluke 732B, 752A, HP


Fixed Points 34420A

1V 0.63 μV/V Fluke 732B, 752A, HP


34420A

10 V 0.55 μV/V Fluke 732B

19 V 1.1 µV/V Fluke 732B, 720A,


752A, HP 34420A

100 V 0.63 μV/V Fluke 732B, 752A, HP


34420A

1000 V 0.82 μV/V Fluke 732B, 752A, HP


34420A

(A2LA Cert. No. 1078.01) 11/21/2023 Page 20 of 53


Parameter/Equipment Range CMC2, 5, 7, 14 (±) Comments

DC Voltage – Generate (0 to 220) mV 5.6 μV/V + 0.39 μV Fluke 5700A/EP


220 mV to 2.2 V 3.2 μV/V + 0.63 mV
(2.2 to 11) V 2.4 μV/V + 2.4 μV
(11 to 22) V 2.4 μV/V + 3.9 μV
(22 to 220) V 3.2 μV/V + 39 μV
(220 to 1100) V 4.8 μV/V + 390 μV

DC Voltage – Measure3 Up to 100 mV 3.0 μV/V + 0.21 μV Agilent/HP 3458A


100 mV to 1 V 2.1 μV/V + 0.21 μV
(1 to 10) V 2.1 μV/V + 0.34 μV
(10 to 100) V 3.5 μV/V + 21 μV
(100 to 1000) V 3.9 μV/V + 74 μV

DC High Voltage – (1 to 6) kV 0.2 % + 1 V Vitrek 4700A


Measure3 (6 to 35) kV 0.4 % + 26 V
(35 to 100) kV 0.4 % + 140 V

DC High Voltage – (1 to 6) kV 0.21 % + 1.1 V Assoc. res. 3565D


Generate3 monitored with Vitrek
4700A

Edge Characteristics –

Amplitude – Measure (0 to 100) mV 3.0 μV/V + 0.21 μV Agilent/HP 3458A/HFL


(0.1 to 1) V 2.1 μV/V + 0.21 μV
(1 to 10) V 2.1 μV/V + 0.34 μV
(10 to 100) V 3.5 μV/V + 21 μV

Electrical Calibration of
RTD Indicating Devices3 –

Pt 385, 100 Ω (-200 to 0) °C 0.05 °C Fluke 5520A


(0 to 100) °C 0.07 °C
(100 to 300) °C 0.09 °C
(300 to 400) °C 0.1 °C
(400 to 630) °C 0.12 °C
(630 to 800) °C 0.14 °C

Pt 3926, 100 Ω (-200 to 0) °C 0.05 °C


(0 to 100) °C 0.07 °C
(100 to 300) °C 0.09 °C
(300 to 400) °C 0.1 °C
(400 to 630) °C 0.26 °C

(A2LA Cert. No. 1078.01) 11/21/2023 Page 21 of 53


Parameter/Equipment Range CMC2 (±) Comments

Electrical Calibration of
RTD Indicating Devices3
(cont) –

PtNi 385, 120 Ω (-80 to 100) °C 0.08 °C Fluke 5520A


(100 to 260) °C 0.16 °C

Pt 385, 200 Ω (-200 to 100) °C 0.04 °C


(100 to 260) °C 0.05 °C
(260 to 300) °C 0.12 °C
(300 to 400) °C 0.13 °C
(400 to 600) °C 0.14 °C
(600 to 630) °C 0.16 °C

Pt 385, 500 Ω (-200 to -80) °C 0.04 °C


(-80 to 100) °C 0.05 °C
(100 to 260) °C 0.06 °C
(260 to 400) °C 0.08 °C
(400 to 600) °C 0.09 °C
(600 to 630) °C 0.11 °C

Pt 385, 1000 Ω (-200 to 0) °C 0.03 °C


(0 to 100) °C 0.04 °C
(100 to 260) °C 0.05 °C
(260 to 300) °C 0.06 °C
(300 to 600) °C 0.07 °C
(600 to 630) °C 0.23 °C

Pt 3916, 100 Ω (-200 to -190) °C 0.25 °C


(-190 to -80) °C 0.04 °C
(-80 to 0) °C 0.05 °C
(0 to 100) °C 0.06 °C
(100 to 260) °C 0.07 °C
(260 to 300) °C 0.08 °C
(300 to 400) °C 0.09 °C
(400 to 600) °C 0.10 °C
(600 to 630) °C 0.23 °C

(A2LA Cert. No. 1078.01) 11/21/2023 Page 22 of 53


Parameter/Equipment Range CMC2 (±) Comments

Electrical Calibration of
Thermocouple Indicating
Devices3 –

Type E (-250 to -100) °C 0.5 °C Fluke 5520A


(-100 to -25) °C 0.16 °C
(-25 to 350) °C 0.14 °C
(350 to 650) °C 0.16 °C
(650 to 1000) °C 0.21 °C

Type J (-210 to -100) °C 0.28 °C


(-100 to -30) °C 0.16 °C
(-30 to 150) °C 0.14 °C
(150 to 760) °C 0.17 °C
(760 to 1200) °C 0.23 °C

Type K (-200 to -100) °C 0.34 °C


(-100 to -25) °C 0.18 °C
(-25 to 120) °C 0.16 °C
(120 to 1000) °C 0.26 °C
(1000 to 1372) °C 0.40 °C

Type S (0 to 250) °C 0.47 °C


(250 to 1000) °C 0.36 °C
(1000 to 1400) °C 0.37 °C
(1400 to 1767) °C 0.46 °C

Type T (-250 to -150) °C 0.63 °C


(-150 to 0) °C 0.24 °C
(0 to 120) °C 0.16 °C
(120 to 400) °C 0.14 °C

(A2LA Cert. No. 1078.01) 11/21/2023 Page 23 of 53


Parameter/Range Frequency CMC2, 8, 14 (±) Comments

High Frequency
Capacitance – Generate,
Fixed Points3 –

1 pF 1 kHz 0.007 % Agilent/HP 16380A


1 MHz 0.01 % series capacitors
2 MHz 0.023 %
3 MHz 0.041 %
4 MHz 0.063 %
5 MHz 0.088 %
10 MHz 0.26 %
13 MHz 0.38 %

10 pF 1 kHz 62 parts in 106


(1, 2) MHz 62 parts in 106
3 MHz 64 parts in 106
4 MHz 67 parts in 106
5 MHz 72 parts in 106
10 MHz 0.013 %
13 MHz 0.017 %

100 pF 1 kHz 61 parts in 106


1 MHz 62 parts in 106
2 MHz 68 parts in 106
3 MHz 82 parts in 106
4 MHz 0.01 %
5 MHz 0.014 %
10 MHz 0.034 %
13 MHz 0.049 %

1000 pF 1 kHz 63 parts in 106


1 MHz 80 parts in 106
2 MHz 0.016 %
3 MHz 0.028 %
4 MHz 0.046 %
5 MHz 0.064 %
10 MHz 0.2 %
13 MHz 0.29 %

0.01 µF (0.12, 1, 10, 100) kHz 63 parts in 106

0.1 µF (0.12, 1, 10, 100) kHz 63 parts in 106

1.0 µF 0.12 kHz 69 parts in 106


(1, 10) kHz 63 parts in 106
100 kHz 85 parts in 106

(A2LA Cert. No. 1078.01) 11/21/2023 Page 24 of 53


Parameter/Range Frequency CMC2, 8, 14 (±) Comments

Inductance3 –

Measure (12 Hz to 0.1 µH to 10 H See Table IV.c LCR meters


2 MHz)

Generate – Fixed 100 µH 0.026 % Standard inductors


Points (1, 5, 10, 100) mH 0.11 %
(1, 2, 5) H 0.11 %

Table IVc: Inductance Measure CMC (in %) Measured with 1689M & 7600 LCR Meters

Freq. 0.1 1 10 100 1 10 100 1 5 10


µH µH µH µH mH mH mH H H H
12 Hz 0.81 1.3 1.1 1.1 1.1
20 Hz 4.8 0.49 0.71 0.58 0.56 0.56
50 Hz 0.97 0.11 0.17 0.26 0.26 0.26
100 Hz 3.6 0.37 0.048 0.069 0.11 0.16 0.16
200 Hz 1.8 0.19 0.048 0.048 0.058 0.11 0.085
500 Hz 4.8 0.49 0.060 0.036 0.036 0.036 0.051 0.036
1 kHz 1.2 0.13 0.024 0.024 0.024 0.024 0.024 0.024
2 kHz 0.90 0.13 0.036 0.042 0.036 0.036 0.048 0.048
5 kHz 3.2 0.37 0.084 0.048 0.062 0.062 0.055 0.079 0.096
10 kHz 1.7 0.22 0.079 0.064 0.062 0.064 0.069 0.097 0.26
20 kHz 0.94 0.15 0.074 0.066 0.066 0.067 0.081 0.030 0.048
50 kHz 4.7 0.54 0.12 0.080 0.075 0.075 0.16 0.50 0.058 0.11
100 kHz 3.4 0.42 0.13 0.095 0.091 0.092 0.21 1.9 0.11 0.20
200 kHz 2.7 0.38 0.15 0.13 0.13 0.13 0.68 4.6
500 kHz 2.4 0.44 0.25 0.23 0.46 0.50 1.9
1 MHz 2.5 0.60 0.41 0.40 0.40 0.96
2 MHz 2.7 0.92 0.75 0.73 0.76 4.3

Parameter/Range Frequency CMC2, 14 (±) Comments

Phase – Generate
5 Vrms (Voltage Ratio 1 Hz to 1 kHz 6.6 m° Clark-Hess 5500-2
= 1) (1 to 6.25) kHz 5.2 m° Ratio = ratio of the
(6.25 to 50) kHz 13 m° larger voltage divided
(50 to 200) kHz 21 m° by the smaller
voltage
50 mVrms to 100 1 Hz to 1 kHz (6.5 + (0.05 ·Ratio)) m°
Vrms (1 to 6.25) kHz (11 + (0.1 · Ratio)) m°
(6.25 to 50) kHz (19 + (0.15 · Ratio)) m°
(50 to 200) kHz (41 + (0.4 · Ratio)) m°

(A2LA Cert. No. 1078.01) 11/21/2023 Page 25 of 53


Parameter/Range Frequency CMC2, 6, 14 (±) Comments

Phase – Generate (cont)


(100 to 120) Vrms 1 Hz to 1 kHz (15 + (0.1 x Ratio)) m° Clark-Hess 5500-2
(1 to 6.25) kHz (21 + (0.2 x Ratio)) m° Ratio = ratio of the
(6.25 to 50) kHz (31 + (0.3 x Ratio)) m° larger voltage divided
(50 to 200) kHz (81 + (1 x Ratio)) m° by the smaller
voltage

Phase – Measure

(0.01 to 0.1) Vrms 10 Hz to 10 kHz 0.21° KH 6620 phase meter


(10 to 50) kHz 0.36°
(50 to 100) kHz 0.71°

(0.1 to 120) Vrms 10 Hz to 50 kHz 0.054°


(50 to 100) kHz 0.036°

Oscilloscope Calibration3 –

Squarewave Signal
50 Ω at 1 kHz Source (1 to 110) mV 0.27 % + 42 µV Fluke 5520A/SC1100
110 mV to 2.2 V 0.27 % + 130 µV scope option
(2.2 to 11) V 0.27 % + 1.2 mV
(11 to 1100) V 0.27 % + 12 mV
Squarewave Signal
1 MΩ at 1 kHz Source (1 to 110) mV 0.15 % + 42 µV
110 mV to 2.2 V 0.15 % + 130 µV
(2.2 to 11) V 0.15 % + 1.2 mV
(11 to 1100) V 0.15 % + 12 mV
Leveled Sine Wave
Flatness (Relative to 50 50 kHz to 100 MHz 1.5 % + 110 µV
kHz) (100 to 300) MHz 2 % + 110 µV
(300 to 600) MHz 4 % + 110 µV
(600 to 1100) MHz 5 % + 110 µV

Period 1 ns to 20 ms 2.0 parts in 106


50 ms 59 parts in 106
100 ms 97 parts in 106
200 ms 180 parts in 106
500 ms 410 parts in 106
1s 800 parts in 106
2s 1600 parts in 106
5s 3900 parts in 106

(A2LA Cert. No. 1078.01) 11/21/2023 Page 26 of 53


Parameter/Range Frequency CMC2, 14 (±) Comments

Oscilloscope Calibration3
– (cont)

Rise Time – Generate 12.8 ps 4.3 ps Tektronix 067-1338-00

Rise Time – Measure > 5.4 ps 5.4 ps Tektronix TDS8000


with 80E03

Parameter/Equipment Range CMC2, 5, 8, 14 (±) Comments

Resistance – Generate, 100 µΩ 29 µΩ/Ω Norma 80


Fixed Points3
1 mΩ 14 µΩ/Ω L&N 4222B
10 mΩ 9.5 µΩ/Ω L&N 4223B
0.1 Ω 6.5 µΩ/Ω L&N resistors

1Ω 4.6 µΩ/Ω Fluke 742A, standard


10 Ω 4.2 µΩ/Ω resistors
100 Ω 2.3 µΩ/Ω
1kΩ 2.5 µΩ/Ω
10 kΩ 1.6 µΩ/Ω
19 kΩ 4.7 µΩ/Ω
100 kΩ 3.3 µΩ/Ω
1 MΩ 4.5 µΩ/Ω
10 MΩ 9.0 µΩ/Ω
100 MΩ 22 µΩ/Ω
1 GΩ 27 µΩ/Ω

10 GΩ 0.13 % IET high resistance


100 GΩ 0.22 % standard
1 TΩ 0.34 %
10 TΩ 1.2 %

Resistance – Measure, DC 100 µΩ 85 μ Ω/Ω + 0.48 nΩ Stable current source,


100 µΩ to1 mΩ 12 μΩ/Ω + 4.8 nΩ 3458A/HFL, standard
(1 to 10) mΩ 9.2 μ Ω/Ω + 4.8 nΩ resistors
(10 to 100) mΩ 5.4 μ Ω/Ω + 48 nΩ
(0.1 to 1) Ω 2.6 μ Ω/Ω + 0.48 μΩ

(A2LA Cert. No. 1078.01) 11/21/2023 Page 27 of 53


Parameter/Equipment Range CMC2, 8, 14 (±) Comments

Resistance – Measure, DC (0 to 2) Ω 3.4 μΩ/Ω + 4.4 μΩ Fluke 8508A & standard


(cont.) (2 to 20) Ω 2.1 μΩ/Ω + 15 μΩ resistors
(20 to 200) Ω 2.6 μΩ/Ω + 33 μΩ
200 Ω to 2 kΩ 2.5 μΩ/Ω + 0.33 mΩ
(2 to 20) kΩ 1.5 μΩ/Ω + 3.3 mΩ
(20 to 200) kΩ 2.3 μΩ/Ω + 33 mW
200 kW to 2 MΩ 4.4 μΩ/Ω + 1.1 Ω
(2 to 20) MΩ 4.4 μΩ/Ω + 11 Ω
(20 to 200) MΩ 8.3 μΩ/Ω + 110 Ω
200 MΩ to 2 GΩ 28 μΩ/Ω + 110 kΩ
(2 to 20) GΩ 0.21 % + 1.1 MΩ

100 MΩ to 1 GΩ 0.081 % 6500A


(1 to 10) GΩ 0.12 %
(10 to 100) GΩ 0.24 %
100 GΩ to 1 TΩ 0.35 %
(1 to 10) TΩ 0.59 %
(10 to 100) TΩ 1.2 %

Parameter/Range Frequency CMC2, 8, 14 (±) Comments

Resistance – Measure, AC 10 Hz to 2 MHz See Table IV.d LCR meters

Table IV.d: AC Resistance Measure CMC (in %) Measured with LCR Meters

0.1 1 10 100 1 10 100 200 500 1


Ω Ω Ω Ω kΩ kΩ kΩ kΩ kΩ MΩ
12 Hz 0.60 0.11 0.11 0.11 0.11 0.11 1.7
20 Hz 0.60 0.11 0.11 0.11 0.11 0.11 0.85 2.8 4.6
50 Hz 3.1 0.31 0.058 0.058 0.058 0.058 0.058 0.38 1.3 2.0
100 Hz 2.3 0.23 0.047 0.047 0.047 0.047 0.047 0.23 0.70 1.2
200 Hz 2.3 0.23 0.047 0.047 0.047 0.047 0.047 0.15 0.44 0.70
500 Hz 1.5 0.16 0.035 0.035 0.035 0.035 0.035 0.10 0.29 0.44
1 kHz 0.77 0.09 0.024 0.024 0.024 0.024 0.024 0.082 0.24 0.35
2 kHz 1.0 0.15 0.035 0.035 0.035 0.035 0.047 0.075 0.21 0.31
5 kHz 0.90 0.14 0.047 0.047 0.047 0.047 0.063 0.072 0.20 0.30
10 kHz 1.0 0.14 0.062 0.055 0.055 0.055 0.063 0.073 0.21 0.30
20 kHz 1.1 0.16 0.066 0.057 0.057 0.057 0.067 0.077 0.22 0.33
50 kHz 1.4 0.19 0.077 0.066 0.065 0.066 0.31 0.37 1.1 1.7
100 kHz 1.9 0.26 0.10 0.081 0.079 0.081 0.40 0.47 1.5 2.2
200 kHz 3.0 0.39 0.14 0.11 0.11 0.12 0.56 0.68 2.2 3.4
500 kHz 0.79 0.26 0.20 0.20 0.26 1.1 1.4 4.2
1 MHz 1.5 0.45 0.35 0.35 0.70 1.9 2.4
2 MHz 2.8 0.85 0.65 0.64 1.4 3.5 4.5

(A2LA Cert. No. 1078.01) 11/21/2023 Page 28 of 53


V. Electrical – RF/Microwave

Parameter/Range Frequency CMC2, 8, 14 (±) Comments

Amplitude Modulation3 –

AM Accuracy:
(0.15 to 10) MHz
(5 to 40) % AM Depth Rate:50 Hz to 10 kHz 2.3 % + 0.012 % AM Measuring receiver
Rate: 20 Hz to 10 kHz 3.5 % + 0.012 % AM

(40 to 99) % AM Depth Rate 50 Hz to 10 kHz 2.3 % + 0.12 % AM


Rate: 20 Hz to 10 kHz 3.5 % + 0.12 % AM

(10 to 1300) MHz


(5 to 40) % AM Depth Rate: 50 Hz to 50 kHz 1.2 % + 0.012 % AM
Rate: 20 Hz to 100 kHz 3.5 % + 0.012 % AM

(40 to 99) % AM Depth Rate: 50 Hz to 50 kHz 1.2 % + 0.12 % AM


Rate: 20 Hz to 100 kHz 3.5 % + 0.12 % AM

(1.3 to 26.5) GHz


(5 to 40) % AM Depth Rate: 50 Hz to 50 kHz 1.7 % + 0.012 % AM Measuring
Rate: 20 Hz to 100 kHz 3.5 % + 0.012 % AM receiver, down
converter & local
(40 to 99) % AM Depth Rate: 50 Hz to 50 kHz 1.7 % + 0.12 % AM oscillator
Rate: 20 Hz to 100 kHz 3.5 % + 0.12 % AM

AM Distortion:
150 kHz to 1.3 GHz <50 % AM Depth 1.1 dB Measuring receiver
(50 to 95) % AM 2.1 dB & distortion
analyzer
(1.3 to 26.5) GHz <50 % AM Depth 1.1 dB
(50 to 95) % AM 2.1 dB
AM Flatness:
(0.01 to 26.5) GHz Rate: 90 Hz to 10 kHz 0.31 % Measuring receiver
(20 to 80) % AM Depth

Distortion Accuracy –
Measure3
(0 to -70) dB (2 to 20) Hz 0.43 dB Low frequency
signal analyzer
(-7 to -99.9) dB 20 Hz to 20 kHz 1.1 dB Distortion analyzer
(-7 to -99.9) dB (20 to 100) kHz 2.1 dB

(A2LA Cert. No. 1078.01) 11/21/2023 Page 29 of 53


Parameter/Range Frequency CMC2, 8 (±) Comments

Frequency Modulation3 –

FM Accuracy Rate:
(0.15 to 10) MHz
<4 kHz FM peak Dev. 20 Hz to 10 kHz 2.4 % + 1.2 Hz Measuring receiver
<40 kHz FM peak Dev. 20 Hz to 10 kHz 2.4 % + 12 Hz

(10 to 1300) MHz


<400 kHz FM pk Dev. 50 Hz to 100 kHz 1.3 % + 120 Hz
20 Hz to 200 kHz 5.8 % + 240 Hz

(1.3 to 26.5) GHz


<400 kHz FM pk Dev. 50 Hz to 100 kHz 1.3 % + 120 Hz Measuring receiver
20 Hz to 200 kHz 5.8 % + 240 Hz & distortion
analyzer
β (0 to 0.5)
Rate: (1 to 3) Hz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 1.6 % 89441A

Rate: 3 Hz to 6.7 GHz


Peak Dev: 3 Hz to 6.7 GHz 3 Hz to 13.2 GHz 1.6 %
E4445A
β 0.5 to 2
Rate: (1 to 3) Hz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 2.1 % 89441A

Rate: 3 Hz to 6.7 GHz


Peak Dev: 3 Hz to 6.7 GHz 3 Hz to 13.2 GHz 1.9 % E4445A

β 2 to 10
Rate: 1 Hz to 3 Hz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 1.2 % 89441A

Rate: 3 Hz to 6.7 GHz


Peak Dev: 3 Hz to 6.7 GHz 3 Hz to 13.2 GHz 1.1 % E4445A

(A2LA Cert. No. 1078.01) 11/21/2023 Page 30 of 53


Parameter/Range Frequency CMC2, 8 (±) Comments

Frequency Modulation3 –
(cont)

β 10 to 100
Rate: 1 Hz to 3 Hz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 0.39 % 89441A

Rate: 3 Hz to 6.7 GHz


Peak Dev: 3 Hz to 6.7 GHz
3 Hz to 13.2 GHz 0.36 % E4445A
β 100 to 200
Rate: 1 Hz to 3 Hz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 0.09 % 89441A

Rate: 3 Hz to 6.7 GHz


Peak Dev: 3 Hz to 6.7 GHz 3 Hz to 13.2 GHz 0.09 % E4445A

β 200 to 500
Rate: 1 Hz to 13 MHz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 0.24 % 89441A

Rate: 1 Hz to 7 MHz
Peak Dev: 1 Hz to 700 (2.6 to 18) GHz 0.24 % 89441A w/ mixer
MHz

β 500 to 5000
Rate: 1 Hz to 13 MHz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 0.14 % 89441A

Rate: 1 Hz to 7 MHz
Peak Dev: 1 Hz to 700 (2.6 to 18) GHz 0.14 % 89441A w/ mixer
MHz

β 5000 to 6 000 000


Rate: 1 Hz to 13 MHz
Peak Dev: 1 Hz to 1.3 GHz 1 Hz to 2.6 GHz 0.03 % 89441A

Rate: 1 Hz to 7 MHz
Peak Dev: 1 Hz to 700 (2.6 to 18) GHz 0.034 % 89441A w/ mixer
MHz

(A2LA Cert. No. 1078.01) 11/21/2023 Page 31 of 53


Parameter/Range Frequency CMC2, 8, 14 (±) Comments

Frequency Modulation3 –
(cont)

FM Distortion
400 kHz to 10 MHz < 10 kHz FM 0.15 % Measuring receiver
Rate: 20 Hz to 10 kHz Deviation

10 MHz to 26.5 GHz < 100 kHz FM 0.15 %


Rate: 20 Hz to 100 kHz Deviation

Residual FM
Carrier Frequency (ƒ) Bandwidth:
< 100 MHz 50 Hz to 3 kHz 1 Hz (rms)
(100 to 1300) MHz 0.4 Hz + (6 x 10-9) ƒ
(1.3 to 6.2) GHz 17 Hz
(6.2 to 12.4) GHz 33 Hz
(12.4 to 18) GHz 49 Hz
(18 to 26.5) GHz 65 Hz

Single Sideband Phase Noise –


Measure
CF = 5 MHz
Range: Offset
-110 dBc/Hz 20 Hz 1.6 dB Agilent E8251A
-126 dBc/Hz 1 kHz 1.3 dB Agilent E4408B
-131 dBc/Hz 20 kHz 1.0 dB
-133 dBc/Hz 100 kHz 1.3 dB HP 89441A w/
-139 dBc/Hz 1 MHz 1.3 dB PMSSBPNMS
-140 dBc/Hz 5 MHz 1.4 dB

CF = 225 MHz
Offset
-101 dBc/Hz 20 Hz 1.3 dB
-114 dBc/Hz 1 kHz 1.0 dB
-139 dBc/Hz 20 kHz 1.0 dB
-140 dBc/Hz 100 kHz 1.1 dB
-146 dBc/Hz 1 MHz 1.4 dB
-148 dBc/Hz 10 MHz 1.4 dB

(A2LA Cert. No. 1078.01) 11/21/2023 Page 32 of 53


Parameter/Range Frequency CMC2, 14 (±) Comments

Single Sideband Phase Noise


– Measure (cont)
CF = 1 GHz
Range: Offset
-89 dBc/Hz 20 Hz 1.6 dB Agilent E8251A
-101 dBc/Hz 1 kHz 1.0 dB Agilent E4408B
-131 dBc/Hz 20 kHz 0.9 dB
-134 dBc/Hz 100 kHz 1.1 dB HP 89441A w/
-145 dBc/Hz 1 MHz 1.4 dB PMSSBPNMS
-147 dBc/Hz 10 MHz 1.4 dB

CF = 5 GHz
Offset
-76 dBc/Hz 20 Hz 1.9 dB
-88 dBc/Hz 1 kHz 1.4 dB
-118 dBc/Hz 20 kHz 0.9 dB
-119 dBc/Hz 100 kHz 1.0 dB
-143 dBc/Hz 1 MHz 1.4 dB
-149 dBc/Hz 10 MHz 2.0 dB

CF = 9.6 GHz
Offset
-70 dBc/Hz 20 Hz 1.1 dB
-82 dBc/Hz 1 kHz 1.2 dB
-113 dBc/Hz 20 kHz 0.9 dB
-116 dBc/Hz 100 kHz 1.0 dB
-141 dBc/Hz 1 MHz 1.9 dB
-144 dBc/Hz 10 MHz 3.0 dB

CF = 15 GHz
Offset
-66 dBc/Hz 20 Hz 1.8 dB
-77 dBc/Hz 1 kHz 1.2 dB
-108 dBc/Hz 20 kHz 1.0 dB
-110 dBc/Hz 100 kHz 1.0 dB
-136 dBc/Hz 1 MHz 1.5 dB
-145 dBc/Hz 10 MHz 3.5 dB

(A2LA Cert. No. 1078.01) 11/21/2023 Page 33 of 53


Parameter/Range Frequency CMC2, 8, 14 (±) Comments

Single Sideband Phase Noise –


Measure (cont)
CF = 18 GHz
Range: Offset
-64 dBc/Hz 20 Hz
-76 dBc/Hz 1 kHz 1.5 dB Agilent E8251A
-107 dBc/Hz 20 kHz 1.4 dB Agilent E4408B
-109 dBc/Hz 100 kHz 0.9 dB
1.0 dB HP 89441A w/
-136 dBc/Hz 1 MHz PMSSBPNMS
-142 dBc/Hz 10 MHz 1.6 dB
3.0 dB

Phase Modulation3 –
(0.15 to 10) MHz
<40 Radians (Peak) Rate: 200 Hz to 10 kHz 4.7 % + 0.012 rad Measuring receiver
<400 Radians (Peak) 4.7 % + 0.12 rad
(10 to 1300) MHz
<4 Radians (Peak) Rate: 200 Hz to 20 kHz 3.8 % + 0.0012 rad
<40 Radians (Peak) 3.5 % + 0.012 rad
<400 Radians (Peak) 3.5 % + 0.12 rad
(1.3 to 26.5) GHz
<4 Radians (Peak) Rate: 200 Hz to 20 kHz 3.7 % + 0.0012 rad Measuring
<40 Radians (Peak) 3.5 % + 0.012 rad receiver, down
<400 Radians (Peak) 3.5 % + 0.12 rad converter & local
oscillator

Parameter/Equipment Range CMC2, 8, 14 (±) Comments

Range Calibration (Power


Meters)3 –
Zero Set (0.03 to 10) mW 0.25 % + 6.2 nW Range calibrator,
Instrument Accuracy 3 µW 1.6 % Agilent 11683A or
10 µW 0.46 % Agilent 8477A
30 µW 0.28 %
(100, 300) µW 0.26 %
(1, 2) mW 0.28 %
(10, 30, 100) mW 0.30 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 34 of 53


Parameter/Range Frequency CMC2, 8, 14 (±) Comments

RF Power Level3 –
Generate/Measure

Absolute 0 dBm @ 50 MHz 0.41 % Signal generator,


power splitter,
(+20 to -128) dBm See Table Vc & Vd attenuator,
0.9 MHz to 26.5 GHz standard sensors,
& power meter

Relative (+20 to -128) dBm See Table Va & Vb E9304A, N8481A,


0.9 MHz to 26.5 GHz 8485A, E4445A
E8244A
Relative 9 kHz 1% Power sensors,
(Power Sensor Calibration 30 kHz 1% splitters, meters
Factors) 100 kHz 1%
300 kHz 1%
1 MHz 1%
3 MHz 1%
10 MHz 0.79 %
30 MHz 0.67 %
100 MHz 0.62 %
300 MHz 0.67 %
1 GHz 0.68 %
2 GHz 0.68 %
3 GHz 0.73 %
4 GHz 0.73 %
5 GHz 0.72 %
6 GHz 0.73 %
7 GHz 0.82 %
8 GHz 0.9 %
9 GHz 0.92 %
10 GHz 0.95 %
11 GHz 0.95 %
12 GHz 0.95 %
13 GHz 1.0 %
14 GHz 1.0 %
15 GHz 1.1 %
16 GHz 1.1 %
17 GHz 1.2 %
18 GHz 1.0 %
19 GHz 1.9 %
20 GHz 2.2 %
21 GHz 2.1 %
22 GHz 2.1 %
23 GHz 2.1 %
24 GHz 2.1 %
25 GHz 2.2 %
26 GHz 2.1 %
26.5 GHz 2.1 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 35 of 53


Table V.a Power Measurement Relative (CMC in dBm, K=2)
FREQUENCY

9 kHz 10 MHz >50 MHz >8 GHz >13.2 GHz 18 GHz


to to 50 MHz to to to to
<10 MHz <50 MHz 8 GHz 13.2 GHz 18 GHz 26.5 GHz
+20 dBm 0.007 0.006 0.008 0.007 0.007 0.010 0.008
+10 dBm 0.007 0.005 0.006 0.006 0.006 0.010 0.006
0 dBm --- ref --- --- ref --- --- ref --- --- ref --- --- ref --- --- ref --- --- ref ---
-10 dBm 0.006 0.006 0.005 0.005 0.006 0.005 0.006
Change From Reference

-20 dBm 0.006 0.006 0.006 0.006 0.006 0.006 0.005


-30 dBm 0.007 0.007 0.007 0.006 0.007 0.006 0.006
-40 dBm 0.008 0.007 0.006 0.006 0.008 0.005 0.006
-50 dBm 0.008 0.007 0.006 0.006 0.008 0.007 0.006
-60 dBm 0.009 0.008 0.007 0.008 0.009 0.008 0.008
-70 dBm 0.010 0.009 0.008 0.009 0.011 0.009 0.008
-80 dBm 0.010 0.009 0.008 0.008 0.009 0.007 0.008
-90 dBm 0.011 0.010 0.010 0.011 0.011 0.009 0.010
-100 dBm 0.016 0.013 0.012 0.013 0.014 0.012 0.010
-110 dBm 0.015 0.011 0.013 0.035 0.031 0.012 0.014
-120 dBm 0.025 0.013 0.019 0.090 0.040 0.014 0.045
-128 dBm 0.041 0.020 0.053 0.11 0.17 0.056 0.095

Table V.b Power Source Relative (CMC in dBm, K=2)


FREQUENCY

9 kHz 10 MHz >50 MHz >8 GHz >13.2 GHz 18 GHz


to to 50 MHz to to to to
<10 MHz <50 MHz 8 GHz 13.2 GHz 18 GHz 26.5 GHz
+20 dBm 0.009 0.007 0.011 0.010 0.010 0.014 0.011
+10 dBm 0.008 0.006 0.006 0.006 0.008 0.015 0.008
0 dBm --- ref --- --- ref --- --- ref --- --- ref --- --- ref --- --- ref --- --- ref ---
-10 dBm 0.007 0.006 0.006 0.006 0.008 0.005 0.007
Change From Reference

-20 dBm 0.008 0.007 0.007 0.008 0.007 0.006 0.006


-30 dBm 0.009 0.009 0.009 0.007 0.008 0.007 0.007
-40 dBm 0.011 0.010 0.008 0.007 0.011 0.006 0.007
-50 dBm 0.012 0.010 0.008 0.007 0.012 0.009 0.007
-60 dBm 0.012 0.011 0.009 0.010 0.014 0.010 0.010
-70 dBm 0.013 0.011 0.010 0.013 0.015 0.011 0.010
-80 dBm 0.013 0.012 0.010 0.010 0.012 0.008 0.009
-90 dBm 0.013 0.011 0.011 0.013 0.014 0.010 0.012
-100 dBm 0.023 0.017 0.016 0.017 0.018 0.015 0.012
-110 dBm 0.024 0.015 0.020 0.064 0.055 0.017 0.022
-120 dBm 0.042 0.018 0.030 0.17 0.073 0.021 0.081
-128 dBm 0.073 0.032 0.096 0.20 0.33 0.10 0.18

(A2LA Cert. No. 1078.01) 11/21/2023 Page 36 of 53


Table V.c Power Measurement Absolute (CMC in dBm, K=2)
FREQUENCY

9 kHz 10 MHz >50 MHz >8 GHz >13.2 GHz 18 GHz


to to 50 MHz to to to to
<10 MHz <50 MHz 8 GHz 13.2 GHz 18 GHz 26.5 GHz
+20 dBm 0.11 0.079 0.055 0.062 0.079 0.082 0.12
+10 dBm 0.11 0.076 0.047 0.055 0.077 0.077 0.12
0 dBm 0.10 0.076 0.047 0.054 0.078 0.078 0.12
-10 dBm 0.10 0.076 0.048 0.055 0.078 0.078 0.12
Change From Reference

-20 dBm 0.10 0.076 0.048 0.055 0.078 0.078 0.12


-30 dBm 0.10 0.077 0.048 0.055 0.078 0.078 0.12
-40 dBm 0.10 0.077 0.048 0.055 0.078 0.078 0.12
-50 dBm 0.10 0.077 0.048 0.055 0.078 0.078 0.12
-60 dBm 0.10 0.077 0.048 0.055 0.079 0.078 0.12
-70 dBm 0.10 0.077 0.048 0.055 0.079 0.078 0.12
-80 dBm 0.10 0.077 0.048 0.055 0.079 0.078 0.12
-90 dBm 0.11 0.077 0.048 0.055 0.079 0.078 0.12
-100 dBm 0.11 0.077 0.049 0.056 0.079 0.078 0.12
-110 dBm 0.11 0.077 0.049 0.065 0.084 0.079 0.12
-120 dBm 0.11 0.077 0.051 0.11 0.088 0.083 0.12
-128 dBm 0.12 0.079 0.071 0.12 0.19 0.088 0.15

Table V.d Power Source Absolute (CMC in dBm, K=2)


FREQUENCY

9 kHz 10 MHz >50 MHz >8 GHz >13.2 GHz 18 GHz


to to 50 MHz to to to to
<10 MHz <50 MHz 8 GHz 13.2 GHz 18 GHz 26.5 GHz
+20 dBm 0.11 0.080 0.056 0.067 0.089 0.094 0.12
+10 dBm 0.11 0.078 0.048 0.060 0.089 0.089 0.12
0 dBm 0.11 0.078 0.049 0.059 0.091 0.090 0.12
-10 dBm 0.11 0.077 0.048 0.055 0.080 0.078 0.12
Change From Reference

-20 dBm 0.11 0.078 0.049 0.056 0.080 0.079 0.12


-30 dBm 0.11 0.079 0.050 0.056 0.080 0.079 0.12
-40 dBm 0.11 0.079 0.049 0.056 0.081 0.078 0.12
-50 dBm 0.11 0.079 0.049 0.056 0.082 0.080 0.12
-60 dBm 0.11 0.080 0.050 0.057 0.083 0.081 0.12
-70 dBm 0.11 0.079 0.050 0.059 0.083 0.081 0.12
-80 dBm 0.11 0.080 0.050 0.056 0.081 0.079 0.12
-90 dBm 0.11 0.078 0.050 0.058 0.081 0.079 0.12
-100 dBm 0.11 0.082 0.052 0.060 0.084 0.081 0.12
-110 dBm 0.11 0.081 0.056 0.094 0.11 0.084 0.12
-120 dBm 0.12 0.082 0.062 0.19 0.12 0.090 0.16
-128 dBm 0.15 0.090 0.12 0.21 0.35 0.14 0.24

(A2LA Cert. No. 1078.01) 11/21/2023 Page 37 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 18 GHz See tables below Network analyzers:


& Transmission) (Interpolate CMC’s 8753ES, E5080A, 8510C
between cardinal calibration kits: 85032B,
points listed) 85054D

Type N: Reflection S11/S22 Linear Magnitude (ρ)


(9 to 300) (0.3 to (0.01 to (3 to 6) (6 to 8) (8 to 9) (9 to 18)
rho kHz 10) MHz 3) GHz GHz GHz GHz GHz
0.01 0.0031 0.0031 0.0045 0.0099 0.0099 0.02 0.02
0.1 0.0031 0.031 0.0045 0.0099 0.0099 0.02 0.02
0.2 0.0031 0.0032 0.0045 0.01 0.01 0.02 0.02
0.3 0.0032 0.0033 0.0047 0.01 0.01 0.02 0.02
0.4 0.0032 0.0034 0.0051 0.011 0.011 0.021 0.021
0.5 0.0033 0.0038 0.0059 0.013 0.013 0.022 0.022
0.6 0.0035 0.0043 0.0071 0.015 0.015 0.024 0.024
0.7 0.0037 0.0051 0.0086 0.018 0.018 0.027 0.027
0.8 0.0039 0.0061 0.011 0.021 0.021 0.031 0.031
0.9 0.0043 0.0072 0.013 0.024 0.024 0.036 0.036
1.0 0.0047 0.0086 0.015 0.028 0.028 0.041 0.041

Type N: Reflection S11/S22 Phase (°)


(9 to 300) (0.3 to (0.01 to (3 to 6) (6 to 8) (8 to 9) (9 to 18)
rho kHz 10) MHz 3) GHz GHz GHz GHz GHz
0.01 18 18 2.7 5.7 80 --- ---
0.1 1.8 0.9 2.6 5.7 5.7 12 12
0.2 0.9 0.9 1.3 2.9 2.9 5.8 6
0.3 0.6 0.62 0.9 2 2 3.9 4.2
0.4 0.46 0.49 0.74 1.6 1.6 3 2.3
0.5 0.38 0.43 0.68 1.5 1.5 2.5 2.8
0.6 0.33 0.41 0.67 1.4 1.4 2.3 2.6
0.7 0.3 0.42 0.7 1.4 1.4 2.2 2.5
0.8 0.28 0.43 0.75 1.5 1.5 2.2 2.5
0.9 0.27 0.46 0.81 1.6 1.6 2.3 2.6
1.0 0.27 0.49 0.88 1.7 1.7 2.4 2.7

(A2LA Cert. No. 1078.01) 11/21/2023 Page 38 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 18 GHz See tables below Network analyzers:


& Transmission) (Interpolate CMC’s 8753ES, E5080A, 8510C
between cardinal points calibration kits: 85032B,
listed) 85054D

Type N: Reflection S21/S12 Linear Magnitude (dB)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 18)
dB kHz MHz GHz GHz GHz GHz GHz
10 0.036 0.031 0.036 0.085 0.085 0.11 0.11
0 0.024 0.016 0.025 0.028 0.028 0.081 0.081
-10 0.026 0.019 0.027 0.03 0.03 0.081 0.081
-20 0.027 0.021 0.028 0.031 0.031 0.081 0.081
-30 0.029 0.023 0.03 0.032 0.032 0.083 0.083
-40 0.033 0.026 0.032 0.044 0.044 0.096 0.096
-50 0.047 0.035 0.039 0.087 0.087 0.14 0.14
-60 0.012 0.084 0.082 0.11 0.11 0.18 0.37
-70 0.31 0.17 0.15 0.17 0.17 0.22 1.1
-80 0.88 0.43 0.33 0.33 0.33 0.36 ---
-90 2.5 1.2 0.89 0.89 0.89 0.9 ---

Type N: Reflection S21/S12 Phase (°)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 18)
dB kHz MHz GHz GHz GHz GHz GHz
10 0.21 0.17 0.21 0.55 0.55 1 1
0 0.16 0.11 0.17 0.36 0.36 0.82 0.82
-10 0.17 0.12 0.17 0.37 0.37 0.82 0.82
-20 0.18 0.13 0.18 0.38 0.38 0.82 0.82
-30 0.19 0.14 0.19 0.38 0.38 0.83 0.83
-40 0.21 0.16 0.2 0.45 0.45 0.9 0.9
-50 0.31 0.22 0.25 0.57 0.57 1.1 1.2
-60 0.78 0.55 0.53 0.74 0.74 1.2 2.7
-70 2.1 1.1 0.98 1.1 1.1 1.4 7.1
-80 6.1 2.9 2.2 2.2 2.2 2.4 ---
-90 20 8.7 6.2 6.2 6.2 6.3 ---

(A2LA Cert. No. 1078.01) 11/21/2023 Page 39 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 26.5 See tables below Network analyzers:


& Transmission) GHz (Interpolate CMC’s 8753ES, E5080A, 8510C
between cardinal calibration kits: 85052D
points listed)

3.5 mm: Reflection S11/S22 Linear Magnitude (ρ)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 20) (20 to 26.5)
rho kHz MHz GHz GHz GHz GHz GHz GHz
0.01 0.0079 0.0079 0.013 0.013 0.013 0.016 0.016 0.032
0.1 0.008 0.008 0.013 0.013 0.013 0.016 0.016 0.032
0.2 0.008 0.008 0.013 0.013 0.013 0.016 0.016 0.032
0.3 0.0081 0.0081 0.013 0.013 0.013 0.016 0.016 0.032
0.4 0.0083 0.0083 0.013 0.013 0.013 0.017 0.017 0.032
0.5 0.0087 0.0087 0.014 0.014 0.014 0.019 0.019 0.034
0.6 0.0095 0.0095 0.016 0.016 0.016 0.021 0.021 0.038
0.7 0.011 0.011 0.019 0.019 0.019 0.024 0.024 0.041
0.8 0.012 0.012 0.022 0.022 0.022 0.029 0.029 0.046
0.9 0.014 0.014 0.026 0.026 0.026 0.035 0.034 0.053
1.0 0.016 0.016 0.031 0.031 0.031 0.041 0.04 0.062

3.5 mm: Reflection S11/S22 Phase (°)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 20) (20 to 26.5)
rho kHz MHz GHz GHz GHz GHz GHz GHz
0.01 --- 53 --- --- --- --- --- ---
0.1 4.6 4.6 7.2 7.2 7.2 9.1 9.4 19
0.2 2.3 2.3 3.6 3.6 3.6 4.6 4.9 9.5
0.3 1.5 1.5 2.4 2.4 2.4 3.1 3.4 6.5
0.4 1.2 1.2 1.9 1.9 1.9 2.4 2.7 5.1
0.5 1 1 1.7 1.7 1.7 2.1 2.4 4.3
0.6 0.9 0.9 1.6 1.6 1.6 2 2.3 3.9
0.7 0.86 0.86 1.5 1.5 1.5 2 2.3 3.7
0.8 0.86 0.86 1.6 1.6 1.6 2.1 2.4 3.7
0.9 0.89 0.89 1.7 1.7 1.7 2.2 2.5 3.8
1.0 0.93 0.93 1.8 1.8 1.8 2.4 2.7 3.9

(A2LA Cert. No. 1078.01) 11/21/2023 Page 40 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 26.5 See tables below Network analyzers:


& Transmission) GHz (Interpolate CMC’s 8753ES, E5080A, 8510C
between cardinal calibration kits: 85052D
points listed)

3.5 mm: Reflection S21/S12 Linear Magnitude (dB)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 20) (20 to 26.5)
dB kHz MHz GHz GHz GHz GHz GHz GHz
10 0.081 0.038 0.057 0.028 0.028 0.15 0.076 0.15
0 0.077 0.028 0.051 0.028 0.028 0.15 0.076 0.15
-10 0.077 0.029 0.052 0.03 0.03 0.15 0.076 0.15
-20 0.078 0.031 0.052 0.032 0.032 0.15 0.077 0.15
-30 0.079 0.032 0.053 0.033 0.033 0.15 0.078 0.16
-40 0.08 0.034 0.055 0.045 0.045 0.15 0.093 0.21
-50 0.087 0.042 0.059 0.089 0.089 0.15 0.14 0.43
-60 0.14 0.087 0.093 0.12 0.12 0.17 0.39 1.5
-70 0.32 0.17 0.16 0.17 0.17 0.21 1.2 5.2
-80 0.89 0.43 0.33 0.34 0.34 0.36 --- ---
-90 2.5 1.2 0.89 0.9 0.9 0.9 --- ---

3.5 mm: Reflection S21/S12 Phase (°)


(9 to 300) (0.3 to 10) (0.01 to 3) (3 to 6) (6 to 8) (8 to 9) (9 to 20) (20 to 26.5)
dB kHz MHz GHz GHz GHz GHz GHz GHz
10 0.53 0.23 0.37 0.36 0.36 0.99 0.81 1.4
0 0.51 0.19 0.35 0.36 0.36 0.98 0.8 1.4
-10 0.51 0.19 0.35 0.37 0.37 0.98 0.81 1.4
-20 0.51 0.2 0.36 0.38 0.38 0.98 0.81 1.4
-30 0.52 0.21 0.36 0.39 0.39 0.99 0.82 1.4
-40 0.53 0.22 0.37 0.45 0.45 0.99 0.89 1.7
-50 0.57 0.27 0.39 0.63 0.63 1 1.2 3.1
-60 0.92 0.57 0.61 0.78 0.78 1.1 2.8 9.9
-70 2.1 1.2 1 1.1 1.1 1.4 7.6 27
-80 6.2 2.9 2.2 2.3 2.3 2.4 --- ---
-90 20 6.7 6.2 6.2 6.2 6.3 --- ---

(A2LA Cert. No. 1078.01) 11/21/2023 Page 41 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 6 GHz See tables below Network analyzers:


& Transmission) (Interpolate CMC’s 8753ES, E5080A
between cardinal calibration kits: 85031B
points listed)

7 mm: Reflection S11/S22 Linear Magnitude (ρ)


rho (9 to 300) kHz (0.3 to 10) MHz (0.01 to 3) GHz (3 to 6) GHz
0.01 0..017 0.0017 0.0026 0.0052
0.1 0.0017 0.0017 0.0027 0.0052
0.2 0.0017 0.0017 0.0027 0.0052
0.3 0.0017 0.0017 0.0027 0.0053
0.4 0.0017 0.0018 0.0028 0.0054
0.5 0.0018 0.0019 0.0029 0.0056
0.6 0.0019 0.002 0.003 0.006
0.7 0.002 0.0022 0.0032 0.0064
0.8 0.0021 0.0025 0.0035 0.007
0.9 0.0023 0.0028 0.0039 0.0079
1.0 0.0025 0.0032 0.0044 0.0088

7 mm: Reflection S11/S22 Phase (°)


rho (9 to 300) kHz (0.3 to 10) MHz (0.01 to 3) GHz (3 to 6) GHz
0.01 --- 9.7 --- 31
0.1 0.95 0.97 1.5 3
0.2 0.48 0.49 0.77 1.5
0.3 0.32 0.33 0.52 1
0.4 0.25 0.26 0.4 0.77
0.5 0.2 0.21 0.33 0.64
0.6 0.18 0.19 0.29 0.56
0.7 0.16 0.18 0.27 0.52
0.8 0.15 0.18 0.26 0.5
0.9 0.14 0.18 0.25 0.5
1.0 0.14 0.18 0.25 0.5

(A2LA Cert. No. 1078.01) 11/21/2023 Page 42 of 53


Parameter/Range Frequency CMC2 (±) Comments

S-Parameters (Reflection 9 kHz to 6 GHz See tables below Network analyzers:


& Transmission) (Interpolate CMC’s 8753ES, E5080A
between cardinal calibration kits: 85031B
points listed)

7 mm: Reflection S21/S12 Linear Magnitude (dB)


dB (9 to 300) kHz (0.3 to 10) MHz (0.01 to 3) GHz (3 to 6) GHz
10 0.029 0.027 0.028 0.037
0 0.013 0.009 0.011 0.027
-10 0.016 0.013 0.014 0.028
-20 0.018 0.016 0.017 0.03
-30 0.021 0.019 0.02 0.032
-40 0.025 0.022 0.023 0.034
-50 0.043 0.032 0.032 0.04
-60 0.11 0.083 0.078 0.082
-70 0.31 0.17 0.15 0.15
-80 0.88 0.43 0.33 0.33
-90 2.5 1.2 0.89 0.89

7 mm: Reflection S21/S12 Phase (°)


dB (9 to 300) kHz (0.3 to 10) MHz (0.01 to 3) GHz (3 to 6) GHz
10 0.16 0.15 0.18 0.22
0 0.086 0.065 0.12 0.18
-10 0.098 0.081 0.13 0.18
-20 0.11 0.098 0.14 0.19
-30 0.13 0.12 0.15 0.2
-40 0.16 0.14 0.17 0.21
-50 0.27 0.21 0.2 0.26
-60 0.77 0.54 0.51 0.53
-70 2.1 1.1 0.97 0.98
-80 6.1 2.9 2.2 2.2
-90 20 8.7 6.2 6.2

(A2LA Cert. No. 1078.01) 11/21/2023 Page 43 of 53


VI. Fluid Quantities

Parameter/Equipment Range CMC2, 8 (±) Comments

Viscosity3 –

Dynamic (Meter) (0 to 100 000) cP 0.83 % Standard viscosity


fluids, PRT, stopwatch
Kinematic (Cups) (0 to 100 000) cP 0.24 % + 0.84 s

Flow Meters3 2 sccm to 650 slm 0.26 % Mass flow system

Hydrometers – Direct Electronic balance,


Verification Class 0 weight set,
master hydrometer

(0.66 to 0.75) sp. gr. 0.000 31 sp. gr. Petroleum solution

(0.75 to 1.00) sp. gr. 0.000 34 sp. gr. Alcohol solution

(1.00) sp. gr. 0.000 21 sp. gr. Distilled water

(1.005 to 1.85) sp. gr. 0.000 26 sp. gr. Sulfuric acid solution

Volumetric Calibration Up to 250 mL 0.08 % + 50 µL Gravimetric method


(>250 to 1200) mL 330 µL
(>1.2 to 8.2) L 0.001 % + 920 µL
(>8.2 to 32) L 0.002 % + 780 µL

(A2LA Cert. No. 1078.01) 11/21/2023 Page 44 of 53


VII. Foundry-Industry Specific Calibrations

Parameter/Equipment Range CMC2, 4, 8 (±) Comments

AFS Clay Tester9 600 s 0.22 s Stopwatch

Mold Strength Tester9 (0 to 50) psi 0.20 % + 0.6R Mold strength tester
& balances

Moisture Teller9 (100 to 300) °F 2.0 °F Temperature


calibrator

Permmeter9 25 perms 2.1 perms Perm standard


90 perms 5.9 perms
160 perms 10 perms

Sand Rammer9 (0.6 to 0.9) inches 0.0066 in + 0.6R Impact rings w/


(Compactability Tester) caliper

Sand Specimen Tube3 2.0 in 0.0014 in Bore gage

Sand (Green) Strength (0 to 500) psi 0.93 % + 0.82 psi Master force
Machine9 proving gage

Welders3 (1 to 50) V 1.0 % Loadbank & DMM


(1 to 750) A 1.0 %

(A2LA Cert. No. 1078.01) 11/21/2023 Page 45 of 53


VIII. Mechanical

Parameter/Equipment Range CMC2, 4, 8 (±) Comments

Accelerometers3
Frequency Response (1 to 10) g, (5 to < 10) Hz 1.8 % 9155C with 353B04
(1 to 10) g, (10 to < 100) Hz 1.3 %
(1 to 10) g, (100) Hz 0.9 %
(1 to 10) g, (> 100 to 920) Hz 1.1 %
(1 to 10) g, > 920 Hz to 5 kHz 1.5 %
(1 to 10) g, (> 5 to 10) kHz 2%
(1 to 10) g, (> 10 to 15) kHz 2.3 %
Voltage Sensitivity
(0.5 to 1000) mV/g, 100 Hz 1.5 %
(0.5 to 1000) mV/g, 159 Hz 1.5 %
Charge Sensitivity
(0.5 to 100) pC/g, 100 Hz 1.5 % 9155C with 353B04
(0.5 to 100) pC/g, 1 kHz 1.5 % & 422M184
Phase
± 360 °, (5 to < 100) Hz 1.6 ° 9155C with 353B04
± 360 °, 100 Hz to < 5 kHz 1.4 °

Air Velocity (141 to 2829) FPM 0.43 % + 12 FPM Wind Tunnel,


(895 to 17 892) FPM 1.1 % + 63 FPM Thermometer,
Flowkinetics
manometer & pitot
tube

Cable Tensiometers/ (0 to 1000) lbf 1.1 lbf + 0.6R Deadweights


Wire Tension Meters

Durometers3 – Types A, B, C, D, E, O & DO ASTM D2240


Pressure Foot Orifice Diameter 3.2 µm
Indenter Shape & Indenter Extension Length 3.2 µm Gage blocks
Extension
Cone Angle 1 arcmin Vision system
Tip Radius 3.2 µm
Indenter Thickness 3.2 μm
Durometer Spring Up to 45 N 36 mN Durometer calibrator
Display Linearity (0.001 to 0.2) in 37 µin or 0.6R, Gage blocks
(Whichever is
Greater)

Durometer Calibrator Scales A, B, E, O & C, D, DO 0.20 % Scale & CMM

(A2LA Cert. No. 1078.01) 11/21/2023 Page 46 of 53


Parameter/Equipment Range CMC2 (±) Comments

Indirect Verification of
Brinell Hardness
Testers at Test
Condition(s)3 –

(3000, 1500, 500) kg 10 mm/500 kg


(50 to 70) HBW 0.13 HBW ASTM E10
(71 to 90) HBW 0.38 HBW
(91 to 109) HBW 1.1 HBW

10 mm/1500 kg
(50 to 99) HBW 0.35 HBW
(100 to 200) HBW 0.56 HBW
(201 to 345) HBW 1.4 HBW

10 mm/3000 kg
(100 to 199) HBW 0.80 HBW
(200 to 499) HBW 1.6 HBW
(500 to 650) HBW 3.7 HBW

Indirect Verification of HLD: ASTM A956


Leeb Hardness Testers Low 8 HLD
Medium 9 HLD
High 10 HLD

Indirect Verification of Vickers, ≤1 kg


Microindentation (100 to 240) HV 11 HV ASTM E384
Hardness Testers (241 to 600) HV 11 HV
(Knoop & Vickers)3 – (600 to > 650) HV 11 HV

Knoop, ≤ 1 kg
(100 to 250) HK 5.3 HK
(251 to 650) HK 5.6 HK
(650 to > 650) HK 5.2 HK

(A2LA Cert. No. 1078.01) 11/21/2023 Page 47 of 53


Parameter/Equipment Range CMC2, 8 (±) Comments

Indirect Verification of HRA:


Rockwell Hardness & Low 0.29 HRA ASTM E18
Rockwell Superficial Mid 0.56 HRA
Hardness Testers3 High 0.24 HRA
HRBW:
Low 0.94 HRB
Mid 0.69 HRB
High 0.62 HRB
HRC:
Low 0.78 HRC
Mid 0.92 HRC
High 0.39 HRC
HRE:
Low 0.92 HRE
Mid 1.1 HRE
High 0.89 HRE
HR15N:
Low 0.76 HR15N
Mid 0.75 HR15N
High 1.1 HR15N
HR30N:
Low 0.55 HR30N
Mid 0.48 HR30N
High 0.46 HR30N
HR45N:
Low 0.68 HR45N
Mid 0.72 HR45N
High 0.66 HR45N
HR15T:
Low 0.79 HR15T
Mid 0.52 HR15T
High 0.61 HR15T
HR30T:
Low 0.70 HR30T
Mid 0.61 HR30T
High 0.42 HR30T
HR45T:
Low 0.98 HR45T
Mid 0.78 HR45T
High 0.81 HR45T

Load Cells & Up to 3325 lbf 0.01 % Dead weights,


Transducers – Load comparison to
Cells, Force Gauges, Up to 2000 lbf 0.036 % + 0.60 lbf master load cell
Force Rings, & (2 to 5.5) klbf 0.028 % + 1.9 lbf
Dynamometers (5.5 to 10) klbf 0.028 % + 4.0 lbf
(10 to 50) klbf 0.21 % + 19 lbf

(A2LA Cert. No. 1078.01) 11/21/2023 Page 48 of 53


Parameter/Equipment Range CMC2, 4, 8 (±) Comments

Mass 1 mg 0.000 87 mg Mass by


2 mg 0.0010 mg substitution
3 mg 0.000 94 mg comparison using
5 mg 0.0012 mg NIST SOP 4 &
10 mg 0.0011 mg NIST SOP 7.
20 mg 0.001 mg
30 mg 0.0011 mg ASTM E617-18
50 mg 0.0013 mg Classes 3 to 7.
100 mg 0.0013 mg NIST Class F.
200 mg 0.0012 mg
300 mg 0.0016 mg
500 mg 0.0014 mg
1g 0.0014 mg
2g 0.0016 mg
3g 0.0022 mg
5g 0.0033 mg
10 g 0.0064 mg
20 g 0.0065 mg
30 g 0.0082 mg
50 g 0.013 mg
100 g 0.022 mg
200 g 0.055 mg
300 g 0.039 mg
500 g 0.043 mg
1 kg 0.06 mg
2 kg 0.28 mg
3 kg 0.56 mg
5 kg 0.84 mg
10 kg 1.1 mg
20 kg 11 mg
30 kg 24 mg
32 kg 24 mg

Pressure/Vacuum Up to 1 inH2O 0.0006 inH2O Pressure


Gauges & Transducers3 (>1 to 5) inH2O 0.0031 inH2O calibrators &
(>5 to 10) inH2O 0.0061 inH2O sensors
(>10 to 100) inH2O 0.0016 % + 0.0058 inH2O
(>100 to 400) inH2O 0.0015 % + 0.0015 inH2O
(-15 to 1500) psig Greater of (0.0092 % +
0.014 psig) or 0.075 psig
(>1500 to 3000) psig 0.004 % + 0.24 psig
(>3000 to 6000) psig 0.0007 % + 0.66 psig
(>6000 to 10 000) psig 0.0038 % + 0.75 psig
Barometric (8 to 17) psig 0.0033 % + 0.0039 psia

(A2LA Cert. No. 1078.01) 11/21/2023 Page 49 of 53


Parameter/Equipment Range CMC2, 8 (±) Comments

Balances3, 11, 12 Up to 30 kg 0.82 x UUT Resolution Class 0, 1, 3 & 4


weight set

Scales3, 12 Up to 1000 lbs 0.82 x UUT Resolution Class F weights

Tachometers3 –
Non-Contact Up to 180 000 rpm 0.8R Calibrator, LED
Contact Up to 5000 rpm 0.024 % + 1.4 rpm Tachometer
(5000 to 15 000) rpm 0.032 % + 0.84 rpm calibrator

Torque
Wrenches, Watches, & Up to 1.5 lbf∙in 0.0076 lbf∙in Torque calibrator
Indicators (>1.5 to 10) lbf∙in 0.17 % + 0.013 lbf∙in
(>10 to 100) lbf∙in 0.25 % + 0.008 lbf∙in
(>100 to 145) lbf∙in 0.38 lbf∙in
(>145 to 3000) lbf∙in 0.28 % + 0.0058 lbf∙in
(>3000 to 24 000) lbf∙in 0.25 % + 3 lbf∙in
Testers, Analyzers & Up to 2000 lbf∙ft 0.05 % Weights, loading
Transducers arms

Ultrasonic Thickness (0 to 10) in 25 µin/in + 850 µin Standard thickness


Testers3 specimen

IX. Optical Quantities

Parameter/Equipment Range CMC2 (±) Comments

Gloss Meters3 20°, 90 ± 10 % GU 0.73 GU Gloss standards;


GU represents
60°, 85°, 95 ± 10 % GU 0.54 GU gloss units.

(A2LA Cert. No. 1078.01) 11/21/2023 Page 50 of 53


X. Thermodynamics

Parameter/Equipment Range CMC2, 4. 8, 14 (±) Comments

Dew Point (-20 to 60) °C 0.44 °C + 0.6R Thunder


Scientific
humidity chamber

Infrared (-15 to 120) °C 0.57 °C + 0.0017 °C/°C Fluke 418x series


Thermometers3 (35 to 500) °C 0.47 °C + 0.0047 °C/°C
(150 to 1200) °C 3.3 °C + 0.0049 °C/°C Isotech Pegasus

Temperature -80 °C, (-30 to 300) °C 0.006 % + 0.017 °C Temperature


Measuring Equipment (300 to 650) °C 0.007 % + 0.039 °C source, SPRT
– Indicators, RTD’s, (650 to 1100) °C 0.018 % + 0.41 °C
Thermocouples3 but Not Less Than 0.02 °C

Relative Humidity –
Measure (5 to 95) % RH 0.9 % + 0.072 % RH Chilled mirror,
but Not Less Than 0.13 % RH RH Systems 973
0.57 % Pressure &
temperature
method
Generate (5 to 95) % RH 0.28 % + 0.44 % RH Thunder
but Not Less Than 0.5 % RH Scientific 2500ST
Psychrometers (5 to 35) °C 0.1 °C + 0.84R Comparison to
SPRT in temp
bath

XI. Time & Frequency

Parameter/Equipment Range CMC2, 14 (±) Comments

Frequency – Measuring 10 MHz 3 parts in 1011 GPS


Equipment & Measure
0.01 Hz to 6 GHz 3.1 parts in 1011 Function
(6 to 26.5) GHz 6.7 parts in 1011 + 1 Hz generator, signal
generator,
frequency counter
or spectrum
analyzer with ext.
GPS timebase

(A2LA Cert. No. 1078.01) 11/21/2023 Page 51 of 53


Parameter/Equipment Range CMC2 (±) Comments

Stopwatches & Timers3 10 s to 24 hr 28 ms + 18 µs/s Function generator,


frequency counter
Up to 19.99 s/day 0.037 s/day Timometer – NIST SP
(86 400 s) 960-12
____________________________________

1
This laboratory offers commercial calibration service and field calibration service.
2
Calibration and Measurement Capability Uncertainty (CMC) is the smallest uncertainty of measurement
that a laboratory can achieve within its scope of accreditation when performing more or less routine
calibrations of nearly ideal measurement standards or nearly ideal measuring equipment. CMCs represent
expanded uncertainties expressed at approximately the 95 % level of confidence, usually using a coverage
factor of k = 2. The actual measurement uncertainty of a specific calibration performed by the laboratory
may be greater than the CMC due to the behavior of the customer’s device and to influences from the
circumstances of the specific calibration.
3
Field calibration service is available for this calibration. Please note the actual measurement uncertainties
achievable on a customer's site can normally be expected to be larger than the CMC found on the A2LA
Scope. Allowance must be made for aspects such as the environment at the place of calibration and for
other possible adverse effects such as those caused by transportation of the calibration equipment. The
usual allowance for the actual uncertainty introduced by the item being calibrated, (e.g. resolution) must
also be considered and this, on its own, could result in the actual measurement uncertainty achievable on
a customer’s site being larger than the CMC.
4
In the statement of CMC, L is the numerical value of the nominal length in inches; R is the resolution of
the unit under test; D is the diameter in inches; H is the height of the unit under test (except where noted);
and fs represents full scale. Ra is the numerical value of the nominal roughness of the surface measured
in micrometer roughness, except where noted; the value is defined as the percentage of reading, unless
otherwise noted.
5
CMC for calibrations performed in the laboratory with the Agilent/HP 3458A/HFL is based upon 90-day
specifications. CMC for calibrations performed field with the Agilent/HP 3458A is based upon 1-year
specifications. The measurands stated are generated with the Agilent/HP 3458A. This capability is
suitable for the calibration of the devices intended to measure the stated measurand in the ranges
indicated. CMC are expressed as either a specific value that covers the full range or as a fraction of the
reading plus a fixed floor specification. Unless otherwise noted, percentages are defined as percent of
reading.
6
CMC for calibrations performed with the Fluke 5520A is based upon 1-year specifications. CMC for
calibrations performed with the Fluke 5720A/EP is based upon 90-day specifications. The measurands
stated are generated with the Fluke 5500, 5700 and 732B series of instruments. This capability is suitable
for the calibration of the devices intended to measure the stated measurand in the ranges indicated. CMC
are expressed as either a specific value that covers the full range or as a fraction of the reading plus a
fixed floor specification. Unless otherwise noted, percentages are defined as percent of reading.

(A2LA Cert. No. 1078.01) 11/21/2023 Page 52 of 53


7
CMC for calibrations performed with the Fluke 5790A is based upon 1-year specifications. The
measurands stated are generated with the Fluke 5700 series of instruments. This capability is suitable for
the calibration of the devices intended to measure the stated measurand in the ranges indicated. CMCs
are expressed as either a specific value that covers the full range or as a fraction of the reading plus a
fixed floor specification. Unless otherwise noted, percentages are defined as percent of reading.
8
In the statement of CMC, the value is defined as the percentage of reading, unless otherwise noted.
9
This calibration is offered for “Field Service” only.
10
Parallelism measurements apply only to optical parallels; calibrated for flatness and parallelism.
11
Balance resolution is not included in the CMC. The uncertainty stated on the Certificate of Calibration
will be larger than the CMC due to the resolution of the balance being included in the reported expanded
uncertainty.
12
Balances and scales are typically calibrated at the place of use. If a balance or scale is not calibrated at
the place of use, the user is responsible to account for any gravitational or air buoyancy errors that may
result.
13
The type of instrument or material being calibrated is defined by the parameter. This indicates the
laboratory is capable of calibrating instruments that measure or generate the values in the ranges indicated
for the listed measurement parameter.
14
The measurands stated are generated using the indicated instrument (see Comments). This capability is
suitable for the calibration of the devices intended to measure the measurand in the ranges indicated.
CMCs are expressed as either a specific value that covers the full range or as a fraction of the reading
plus a fixed floor specification.
15
This scope meets A2LA’s P112 Flexible Scope Policy.

(A2LA Cert. No. 1078.01) 11/21/2023 Page 53 of 53


Accredited Laboratory
A2LA has accredited

TRESCAL, INC.
Milwaukee, WI
for technical competence in the field of

Calibration
This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2017
General requirements for the competence of testing and calibration laboratories. This laboratory also meets the requirements of
ANSI/NCSL Z540-1-1994 and R205 – Specific Requirements: Calibration Laboratory Accreditation Program. This accreditation
demonstrates technical competence for a defined scope and the operation of a laboratory quality management system
(refer to joint ISO-ILAC-IAF Communiqué dated April 2017).

Presented this 21st day of November 2023.

_______________________
Mr. Trace McInturff, Vice President, Accreditation Services
For the Accreditation Council
Certificate Number 1078.01
Valid to May 31, 2025

For the calibrations to which this accreditation applies, please refer to the laboratory’s Calibration Scope of Accreditation.

You might also like