ORDER NO.

CRT3597
DEH-30MP/XU/EW

HIGH POWER CD/MP3/WMA PLAYER WITH RDS TUNER

DEH-30MP /XU/EW

This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks

CX-3164 CRT3583 S10.5COMP1 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2005
K-ZZW. DEC. 2005 Printed in Japan
 1 2 3 4

SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

- Safety Precautions for those who Service this Unit.

• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.

Caution:
B 1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

- CD Section Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
C described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.

DEH-30MP/XU/EW
2
1 2 3 4
 5 6 7 8

[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

0 Safe environment should be secured during servicing. D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-30MP/XU/EW
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SPECIFICATIONS ............................................................................................................................................ 5
A
2. EXPLODED VIEWS AND PARTS LIST ............................................................................................................ 6
2.1 PACKING ................................................................................................................................................... 6
2.2 EXTERIOR................................................................................................................................................. 8
2.3 CD MECHANISM MODULE..................................................................................................................... 10
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .......................................................................................... 12
3.1 BLOCK DIAGRAM ................................................................................................................................... 12
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE).............................................................................. 14
3.3 KEYBOARD UNIT.................................................................................................................................... 20
3.4 CD MECHANISM MODULE(GUIDE PAGE) ............................................................................................ 22
4. PCB CONNECTION DIAGRAM ..................................................................................................................... 32
4.1 TUNER AMP UNIT................................................................................................................................... 32
4.2 KEYBOARD UNIT.................................................................................................................................... 36
B 4.3 CD CORE UNIT(S10.5COMP1)............................................................................................................... 38
5. ELECTRICAL PARTS LIST ............................................................................................................................ 40
6. ADJUSTMENT ............................................................................................................................................... 45
6.1 CD ADJUSTMENT................................................................................................................................... 45
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT .................................................... 47
6.3 ERROR MODE ........................................................................................................................................ 49
7. GENERAL INFORMATION ............................................................................................................................. 50
7.1 DIAGNOSIS ............................................................................................................................................. 50
7.1.1 DISASSEMBLY ..................................................................................................................................... 50
7.1.2 CONNECTOR FUNCTION DESCRIPTION .......................................................................................... 53
7.2 PARTS...................................................................................................................................................... 54
7.2.1 IC .......................................................................................................................................................... 54
C 7.2.2 DISPLAY ............................................................................................................................................... 64
7.3 OPERATIONAL FLOW CHART ............................................................................................................... 65
8. OPERATIONS ................................................................................................................................................ 66

DEH-30MP/XU/EW
4
1 2 3 4
 5 6 7 8

1. SPECIFICATIONS

DEH-30MP/XU/EW
5 6 7 8
5
 1 2 3 4

2. EXPLODED VIEWS AND PARTS LIST

NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
"
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING

B 3 16
6 1
5 2
9

13

DEH-30MP/XU/EW
6
1 2 3 4
 5 6 7 8
PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 Accessory Assy CEA4610 13 Protector YHP5009

2 Screw Assy CEA6002 14 Protector YHP5008
A
3 Fixing Screw(M2x4) CBA1994 15 Polyethylene Bag CEG-162
4 Screw CBA1650
* 5 Polyethylene Bag CEG-127 16-1 Owner's Manual YRD5060
16-2 Owner's Manual YRD5061
6 Screw CRZ50P090FTC 16-3 Owner's Manual YRD5062
7 Screw TRZ50P080FTC 16-4 Installation Manual YRD5059
* 8 Polyethylene Bag CEG-158 * 16-5 Passport CRY1013
9 Handle CNC5395
10 Bush CNV3930 * 16-6 Warranty Card CRY1157
17 Case Assy CXB3520
11 Carton YHG5075 18 Cord Assy CDE7059 B
12 Contain Box YHL5075

Owner's Manual,Installation Manual

Part No. Language

YRD5060 English, Spanish

YRD5061 German, French

YRD5062 Italian, Dutch, Russian

YRD5059 English, Spanish, German, French, Italian, Dutch, Russian
C

DEH-30MP/XU/EW
5 6 7 8
7
 1 2 3 4

2.2 EXTERIOR
39
5 31 37 34
A 38
41
40
14 42
45
43 33
46
42
57 46 C 36
6
42
35
B 46 32
53
55 66
B 62
74 46
55
53
51 12
65
60 50 67
70
61 68
52 63
64
49
47
69 54 9
48
58 15 A 9 8
C
56 59 8

2 3 28
16 72 18
2 25
2 30
73
2 16 29 17 71
73
22 B
23 19 17 26
21
20
27
D
11 A 24
10

13
E
A 7
4
B 4

44 4

DEH-30MP/XU/EW
8
1 2 3 4
 5 6 7 8
EXTERIOR SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 Screw ASZ26P050FTC 50 Button(EQ,BAND/ESC) YAC5075

2 Screw BSZ26P060FTC A
3 Screw BSZ30P060FTC 51 Button(ATT,DISP/SCRL) YAC5076
4 Screw BSZ30P200FTC 52 Button(EJECT,TA/AF) YAC5077
5 Cord Assy CDE7059 53 Button(UP,DOWN) YAC5079
54 Button(DETACH) YAC5080
6 Cap CKX-003 55 Button(LEFT,RIGHT) YAC5102
7 Holder CNC8659
8 Earth Plate CNC8915 56 Spring YBH5003
9 Cushion CNM8890 57 Cover YNS5121
10 CD Mechanism Mudule(S10.5) CXK5750 58 Ring YNS5123
59 Ring YNS5124
11 Cable YDE5013 60 Lens YNV5036 B
12 Case YNB5008
13 Insulator YNM5012 61 Lens YNV5037
14 Panel YNS5125 62 Connector(CN1801) CKS4943
15 Tuner Amp Unit YWM5113 63 LCD(LCD1801) YAW5064
64 Holder YNC5016
16 Screw ASZ26P060FTC 65 Sheet YNM5026
17 Screw BPZ26P080FTC
18 Screw BSZ26P160FTC 66 Cushion YNM5027
> 19 Fuse(10A) CEK1208 67 Connector YNV5040
20 Pin Jack(CN353) CKB1051 68 Lighting Conductor YNV5041
69 Grille Unit YXA5143 C
21 Plug(CN901) CKM1376 70 Button Unit(AUDIO,FUNC) YXA5144
22 Connector(CN701) CKS3834
23 Connector(CN803) CKS4944 71 IC(IC301) PAL007B
24 Antenna Jack(CN401) CKX1056 72 IC(IC921) NJM2388F84
25 Holder CND1328 73 Transistor(Q702,911) 2SD2396
74 IC(IC1802) TSOP4840SB1
26 FM/AM Tuner Unit CWE1951
27 Holder CND1054
28 JACK(CN621) YKS5001
29 Holder YNC5017
D
30 Heat Sink YNR5004

31 Panel Unit YXA5154

32 Button(DETACH) CAC4836
33 Spring CBH1835
34 Spring CBH2208
35 Spring CBH2367

36 Bracket CNC6791
* 37 Holder CNC8042
38 Cover CNM6276 E
39 Arm CNV4692
40 Arm CNV4728

* 41 Arm CNV5576
42 Screw IMS20P030FTB
* 43 Panel YNS5046
44 Chassis Unit YXA5168
45 Detachable Assy YXA5169

46 Screw BPZ20P080FTB
47 Spring CBH2210 F
48 Knob(SOURCE,VOLUME) YAA5008
49 Button(1-6) YAC5074

DEH-30MP/XU/EW
5 6 7 8
9
 1 2 3 4

2.3 CD MECHANISM MODULE

DEH-30MP/XU/EW
10
1 2 3 4
 5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.

1 CD Core Unit(S10.5COMP1) CWX3176 50 Rack CNV8342

2 Connector(CN101) CKS4808 A
3 Connector(CN901) CKS5284 51 Roller CNV8343
4 Screw BMZ20P025FTC 52 Holder CNV8344
5 Screw BSZ20P040FTC 53 Arm CNV8345
54 Guide CNV8347
6 Screw(M2 x 3) CBA1511 55 Arm CNV8348
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038 56 Arm CNV8349
9 ••••• 57 Arm CNV8350
10 Spring CBH2609 58 Clamper CNV8365
59 Arm CNV8386
11 Spring CBH2612 60 Guide CNV8396 B
12 Spring CBH2614
13 Spring CBH2616 61 Arm CNV8413
14 Spring CBH2617 62 Collar CNV8447
15 Spring CBH2620 63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
16 Spring CBH2855 65 Chassis Unit CXC4028
17 Spring CBH2937
18 Spring CBH2735 66 Gear Unit CXC4029
19 Spring CBH2854 67 Frame Unit CXC4031
20 Spring CBH2642 68 Motor Unit(M1) CXC4166
69 Screw Unit CXC6359 C
21 Spring CBH2856 70 Screw JFZ20P020FTC
22 Spring CBH2857
23 Spring CBH2860 71 Screw JGZ17P022FTC
24 Spring CBH2861 72 Washer YE20FTC
25 Spring CBL1686 73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND2584
D
30 Lever CND2585

31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201

36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211

41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV8189
45 Gear CNV7219

46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV8448
49 Arm CNV7805

DEH-30MP/XU/EW
5 6 7 8
11
 1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM
A
VDD5

TUNPDO
TUNPCK
TUNPDI
FM/AM TUNER UNIT
7 6 13 5 10 9 8 11 14 18 19 20 21

NC

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
IC 3 EEPROM IC 5
←
5.0V 5V 3.3V

OSC LPF

B ANTENNA CN401
AM ANT FMRF
1
1 ATT
Rch
2 24
RDS-CK
IC 2
IC 1 2.5V
FM ANT RDS-HSLK
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER
RF adj RDS-LOCK
ANT adj

RDS-DATA

T51 CF52

EL
S
AUDIOGND

IC 4
OSCGND

TUNL
VDD_3.3

← 2
RFGND

3.3V 3.3V 2.5V 2.5V IN

DGND

VCC

C
NC

2 12 15 22 16 4 17

VDD_3.3V
VCC8
3
IN
1
IN

A TUNER AMP UNIT

CN621
AUX-L 3 IC 751 1
5
NJM4558MD
AUX IN
KEY1 34
3 KEYD
WIRED REMOTE CONTROL 2 KEY2 94
KEYAD

PICKUP UNIT SYSTEM C

(P10.5)(SERVICE) C
D CD CORE UNIT(S10.5COMP1) IC 6
PEG

CN101 V3R3D
LASER CN901 CN701
DIODE LD- 142
15 15 LD 31 LOUT LOUT
IC201 LOUT 16 16
Q101
MD
5 5
143
PD UPD63763CGJ
REFO 133
VREF 8 REFOUT
8 RF-AMP,CD DECODER, 34
AC,BD MP3 , WMA, DECODER, XTAL
HOLOGRAM
UNIT
F,E
DIGITAL SERVO / DATA PROCESSOR X201
16.93MHz
FOM
3 3
FOM /XTAL 35
FOP FOP LOCK/RFOK
FOCUS ACT. 2 2
MONITOR TOP 56
DIODE TRACKING ACT. 1 1 TOP
TOM TOM TD,FD SD,MD
4 4 XRST,XASTB,ADO,XCK,
LD+ XSO,XSI,WAIT,XINT
14 14
12
FOM
CD VDD
11 DRIVER
E 14
FOP
TOP
Q701
VDD
11 VDD5
SWVDD 11
13
TOM
63
SPINDLE IC301
MOTOR M BA5835FP LOCK /CD3VON
43
16 14 /RESET /RESET 21
SOP CLCONT 21 41 RESET 10 10 CDRST
15 CLCONT 39 CDMUTE
SOM CDMUTE 8 8
18 22 40
LCOP LOEJ LOEJ
LOAD/ CARRIAGE
MOTOR M 17
LCOM CONT
9 47 IC701 BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
CONT PE5505A
BDATA,BSCK
CD CONTROLLER Q702
VD VD
VD 1 1
X1 12 B.UP
32 Q701
12EJ X701 2 2 3 4
31 4.00MHz
8EJ 5
30 X2 13
DSCSNS
2
42
HOME
S904 S905 S901 49 VDCONT VDCONT
12EJ 8EJ HOME VDCONT 9 9
CD3VON
46
S903
DSCSNS

1
4 IC203
F V3R3D
NJM2886DL3-33 3
VD

+3.3V REGULATOR

DEH-30MP/XU/EW
12
1 2 3 4
 5 6 7 8

CN353
RESET
SWL 2
1 IC 961 2 SUBWOOFER OUT
VDD5
BD4843G Q351

12 RCFL 6
FRONT OUT
RESET
Q353

TUNPDO 68
TPDI
LDET 75
LDET
TUNPDI 86
TPDO
SL 97
SL
TUNPCK 67 TPCK
VDD5V REG.
CE1 66 Q911
TUNPCE1
CE2 65 TUNPCE2 VDD5
Q912 B
SYSTEM CONTROLLER
IC 601(1/2)
Q401 47
PEG159A DALMON
RDS-CK 74
RCK

RDS-HSLK 83 CN901
RDS57K BACKUP SENSE B.UP
19 BSENS
BSENS 16 16
Q402 BACK UP
81 Q931
RDS-LOCK 20 ASENS ACC
RDSLOCK ASENS 14 14
ACC
RDS-DATA 82
RDSDT ACC SENSE

15 15
GND

B.UP
AMP 20 6

ELECTRONIC VOLUME/ VCC VCC

SOURCE SELECTOR
TUNL 6 14
2 FRONT_L FLIN FL− 23 FL−
IN2−_L IC 301 7 7
21 FL+ FL−
PRE/SW_L
12 PAL007B FL+
3 RL−
5 5
FL+
C
7 12 RL− 8 8
REAR_L RLIN 5 RL+ RL−
RL+ 6 6
RL+
IC 151
PML015A 22 25 BREM
MUTE STBY B.REM 11 11
3 B.REM
IN3_L 4
1
IN1_L
TEL
MUTE 9 9
Q453 VCC8
VCK, VDT, VST

B.UP
TUN3V REG. SYS 8V REG.

VDD_3.3V
3 IC 401 1 2 IC 921 1
B.UP
NJM2885DL1-33 NJM2388F84
Q451 4
53
MUTE
SYSPW

34
KEYD
94 RR RR
KEYAD − +
48 SYSPW
SYSPW
BACK FR FR
UP − +
B. FL FL D
REM − +

GND ACC RL RL
− +
SYSTEM CONTROLLER
IC 601(2/2)
PEG159A Q951
38
TELIN VDD5

13
XOUT
X601
15
XIN

B KEYBOARD UNIT
CN803 CN1801
Q851 KEY MATRIX
SWVDD
VDD5 3 8 SWVDD
Q852 S1801 S1802 S1803 S1804 S1805
FUNC BAND 1 4 2
7
SWVDD E
S1806 S1807 S1808 S1818 S1809
18 DSENS DSENS
DSENS 10 1 RIGTH LEFT 3 6 5
D1804-D1822
21
CDRST Q841
ILMB+ ILM S1810 S1811 S1812
B.UP 5 6 EQ
DOWN UP

Q842
S1813 S1814 S1815 S1816 S1817
1
ILMPW AUDIO TA DISP EJECT ATT
B.UP

S1827 SWVDD
92 SSENS SRC 4
SSENS 4 7 REM.CON.
3 ROT1 ROT1 1 3 IC1802 1
ROT1 6 5
4 ROT0 ROT0 2
TSOP4840SB1
ROT0 7 4
17
SOURCE REM KEY DATA 22
VOLUME XO
X1801
35 DPDT DPDT 18 23 5MHz
DPDT 8 3 DPDT XI
LCD DRIVER/
KYDT
36 KYDT
9 2
KYDT 20
KYDT KEY CONTROLLER F
10 IC 1801
VLCD PD6340A LCD1801
56
VDD

DEH-30MP/XU/EW
5 6 7 8
13
 1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)

Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A
Large size
SCH diagram
A-a
A-a A-b

FM : -20dBs
C CN901
AM : -20dBs
A-a A-b Guide page

A-a A-b Detailed page

471/16
FM/AM TUNER UNIT

B CD : 0.35dBs

ANTENNA

15.000MHz
AUX : 2.21dBs
AUX IN

SYSTEM MICROCOMPUTER
WIRED REMOTE CONTROL

B
CN1801

A
DEH-30MP/XU/EW
14
1 2 3 4
 5 6 7 8

A
A-b
A TUNER AMP UNIT

PRE-SUB WOOFER
OUTPUT

FM : -2.9dBs >
PRE-FRONT
AM : -2.9dBs
CD : 10.45dBs OUTPUT
AUX : 10.31dBs 3A

332/16
COMPUTER
>
CEK1208 BACKUP
600µH 10A

GND

ACC

B.REM

TEL
471/16

RL–
D
FL–

RL+

FL+

RR–

FR–

RR+

FR+

FM : 23.1dBs
AM : 23.1dBs
CD : 36.45dBs
AUX : 36.31dBs

NOTE :
Symbol indicates a resistor. For resistors and capacitors in the circuit diagrams, their resistance
No differentiation is made between chip resistors and values or capacitance values are expressed in codes:
discrete resistors.
RR RR
Symbol indicates a capacitor. Ex. *Resistors - +
No differentiation is made between chip capacitors and Code Practical value
discrete capacitors. 123 12k ohms
BACK FR FR
103 10k ohms
UP - +
The > mark found on some component parts indicates B. FL FL
the importance of the safety factor of the part. *Capacitors REM - +
Therefore, when replacing, be sure to use parts of
identical designation.
Code Practical value
GND ACC RL RL F
103 0.01uF - +
101/10 100uF/10V

A
DEH-30MP/XU/EW
5 6 7 8
15
 F
E
B
A

D
C

16
A-a A-b

A-a
A-b
C CN901

1
1

FM : -20dBs
AM : -20dBs

471/16
CD : 0.35dBs

2
2

FM/AM TUNER UNIT

F
A
C
A

DEH-30MP/XU/EW
3
3

ANTENNA
2

15.000MHz

AUX : 2.21dBs

AUX IN

4
4

SYSTEM MICROCOMPUTER

EMOTE CONTROL
 5 6 7 8

3 4 5 6 7 8 A-b

A-a A-b
D
CN1801
B

A-a
WIRED REMOTE CONTRO

DEH-30MP/XU/EW
5 6 7 8
17
 F
E
B
A

D
C

18
A-a A-b
A TUNER AMP UNIT

A-b
1
1

PRE-SUB WOOFER
OUTPUT

2
2

1
FM : -2.9dBs >
AM : -2.9dBs
PRE-FRONT
CD : 10.45dBs OUTPUT
AUX : 10.31dBs 3A

DEH-30MP/XU/EW
3
3

2
332/16

4
4

>
CEK1208 BACKUP
600µH 10A

GND

ACC

B.REM
 CEK1208 BACKUP
600µH 10A

GND

ACC

B.REM

TEL

RL–
5

5
471/16
FL–

RL+

FL+

3
RR–

FR–

RR+

4
FR+

FM : 23.1dBs
AM : 23.1dBs
CD : 36.45dBs
AUX : 36.31dBs

6
6

DEH-30MP/XU/EW
6

7
7

NOTE :
Symbol indicates a resistor. For resistors and capacitors in the circuit diagrams, their resistance

7
No differentiation is made between chip resistors and values or capacitance values are expressed in codes:
discrete resistors.
RR RR
Symbol indicates a capacitor. Ex. *Resistors - +
No differentiation is made between chip capacitors and Code Practical value
BACK FR FR
discrete capacitors. 123 12k ohms
UP - +
103 10k ohms
The > mark found on some component parts indicates B. FL FL
the importance of the safety factor of the part. *Capacitors REM - +

8
Therefore, when replacing, be sure to use parts of Code Practical value
identical designation. GND ACC RL RL
103 0.01uF - +
8

8
101/10 100uF/10V

A-a A-b

A-b
19
E
A

D
C

F
B
 1 2 3 4

3.3 KEYBOARD UNIT

C
5.00MHz

LCD DRIVER

B
DEH-30MP/XU/EW
20
1 2 3 4
5 6 7 8

B KEYBOARD UNIT

A
CN803

B
DEH-30MP/XU/EW
5 6 7 8
21
 1 2 3 4

3.4 CD MECHANISM MODULE(GUIDE PAGE)

A
C-a

C
S

F
C
S

F
B
PICKUP UNIT(P10.5)(SERVICE)
$

F
F
T
T

T
F
@
T
F !
C F
T

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.

NC
NC
NC
NC
NC
M1 CXC6742 CD DRIVER NC
NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC
C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
E NC
NC
F
F
3 T
T

2
C
C
S
S

C
DEH-30MP/XU/EW
22
1 2 3 4
 5 6 7 8

A
C-b

B
SIGNAL LINE Decimal points for resistor
F and capacitor fixed values
FOCUS SERVO LINE
T are expressed as :
TRACKING SERVO LINE 2.2 ← 2R2
C
CARRIAGE SERVO LINE 0.022 ← R022
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)
0

+ 3.3 V REGULATOR C

D
NC
NC
NC
NC
NC

NC
NC
NC
NC
NC

NC
NC

NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC
NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER (S905) E
NC
NC
NC

A CN701

C
DEH-30MP/XU/EW
5 6 7 8
23
 F
E
B
A

D
C

24
C-a
A-a C-b

C-a
C-b

1
1

T
F

S
C
1

T
F

S
C

2
2

PICKUP UNIT(P10.5)(SERVICE)
$

DEH-30MP/XU/EW
F
F
T
T

3
3

T
F
@
T
F !
F
T

4
4

SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF

The underlined indicates the switch position.

 SWITCHES:
CD CORE UNIT(S10.5COMP1)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5

5
2
NC
NC
NC
NC

NC
M1 CXC6742 CD DRIVER NC
SPINDLE MOTOR
NC
S
NC
S NC
NC
C NC
# NC

6
6

C
NC
NC
M2 CXC4026 T S NC
LOADING/CARRIAGE MOTOR
NC
8 6
NC
F C NC

7
9

4
NC
NC
F
F

DEH-30MP/XU/EW
3 T
T

7
7

S
S
C
C

1
3
8

8
C-a
A-a C-b

C-a
C-b

25
E
A

D
C

F
B
 F
E
B
A

D
C

26
C-a C-b

C-b
1
1

2
2

SIGNAL LINE Decimal points for resistor

F and capacitor fixed values
FOCUS SERVO LINE
T are expressed as :
TRACKING SERVO LINE 2.2 ← 2R2
C
CARRIAGE SERVO LINE 0.022 ← R022
S
SPINDLE SERVO LINE

C CD CORE UNIT(S10.5COMP1)

DEH-30MP/XU/EW
0

3
3

+ 3.3 V REGULATOR

4
4
 5

5
2
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC CD3VON(MCKRQ)
NC SRAMLEVEL2
NC
NC ADENA
NC

6
6

NC
NC
NC
NC
NC
NC SRAMLEVEL1
SRAMLEVEL0
5

(S904)
CD CONTROLLER (S905)
NC
NC

DEH-30MP/XU/EW
NC

7
7

A CN701

3
8

8
C-a C-b

C-b
27
E
A

D
C

F
B
 1 2 3 4

- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div
2 8SNS 5 V/div 4 CLCONT 5 V/div 2 8SNS 5 V/div
3 12SNS 5 V/div 5 VD 10 V/div 3 12SNS 5 V/div

12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:

GND GND GND

Mode: Mode: Mode:

B Normal Normal Normal

6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div 6 SIN 1 V/div 1 s/div

7 CIN 500 mV/div 7 CIN 500 mV/div 7 CIN 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation 12 cm CD-ROM(3 sessions) setup operation
after loading after loading

C Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

9 FIN 200 mV/div 500 ms/div ! TE 500 mV/div 200 ms/div @ FE 500 mV/div 20 ms/div
0 RFOK 2 V/div @ FE 500 mV/div 9 FIN 500 mV/div
6 SIN 2 V/div ! TE 500 mV/div
8 TIN 500 mV/div
12 cm CD-DA Source On setup operation Source On setup operation CD-DA Play operation
D

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

@ FE 500 mV/div 20 ms/div # MDX 2 V/div 50 ms/div # MDX 2 V/div 5 µs/div

9 FIN 500 mV/div 6 SIN 200 mV/div 6 SIN 500 mV/div
E
! TE 500 mV/div
8 TIN 500 mV/div
CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

DEH-30MP/XU/EW
28
1 2 3 4
 5 6 7 8

9 FIN 500 mV/div 200 ms/div ! TE 500 mV/div 2 ms/div $ RFAGC 1 V/div 500 µs/div
@ FE 500 mV/div $ RFAGC 500 mV/div ! TE 500 mV/div A
8 TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

TEST TEST TEST

$ RFAGC 1 V/div 500 µs/div $ RFAGC 1 V/div 1 ms/div $ RFAGC 1 V/div 2 ms/div
! TE 500 mV/div ! TE 500 mV/div ! TE 500 mV/div
8 TIN 500 mV/div 8 TIN 500 mV/div 8 TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO
C
Mode: Mode: Mode:
TEST TEST TEST

$ RFAGC 1 V/div 200 ms/div % LOUT 1 V/div 200 µs/div 1 DSCSNS 5 V/div 500 ms/div
! TE 1 V/div ^ ROUT 1 V/div 2 8SNS 5 V/div
7 CIN 500 mV/div 3 12SNS 5 V/div
6 SIN 2 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

D
Ref.: Ref.: Ref.:
REFO AGND GND

Mode: Mode: Mode:

Normal Normal Normal

1 DSCSNS 5 V/div 500 ms/div 1 DSCSNS 5 V/div 500 ms/div 6 SIN 1 V/div 500 ms/div
5 CLCONT 5 V/div 2 8SNS 5 V/div 7 CIN 500 mV/div
4 LOEJ 5 V/div 3 12SNS 5 V/div 8 TIN 500 mV/div
E
12 cm CD Eject operation 8 cm CD Eject operation CD-DA → CD-ROM mode change(Band key)

Ref.: Ref.: Ref.:

GND GND REFO

Mode: Mode: Mode:

Normal Normal Normal

DEH-30MP/XU/EW
5 6 7 8
29
 1 2 3 4

6 SIN 1 V/div 500 ms/div $ RFAGC 1 V/div 500 µs/div

A 7 CIN 500 mV/div 8 TIN 1 V/div
8 TIN 500 mV/div ! TE 1 V/div
9 FIN 1 V/div
CD-ROM → CD-DA mode change(Band key) Black dot(800 µm) during play

Ref.: Ref.:
REFO REFO

Mode: Mode:
Normal Normal

DEH-30MP/XU/EW
30
1 2 3 4
5 6 7 8

DEH-30MP/XU/EW
5 6 7 8
31
 1 2 3 4

4. PCB CONNECTION DIAGRAM

4.1 TUNER AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
several destination.
For further information for AUX IN
respective destinations, be sure
WIRED REMOTO CONTROL
to check with the schematic dia-
gram.
2.Viewpoint of PCB diagrams CN621
Connector Capacitor 2 3

5 1 4 6
SIDE A

B
SIDE B
P.C.Board Chip Part

D
CN701
20
19

15

10

C CN901
5
2
1

F
B CN1801

A
DEH-30MP/XU/EW
32
1 2 3 4
5 6 7 8

A
SIDE A

FRONT SUBWOOFER
OUT OUT ANTENNA

5 8 1 4
6 7 2 3

FM/AM TUNER UNIT

D

FRONT A
DEH-30MP/XU/EW
5 6 7 8
33
 1 2 3 4

A
A TUNER AMP UNIT

A FRONT
DEH-30MP/XU/EW
34
1 2 3 4
 5 6 7 8

A
SIDE B

FRONT A
DEH-30MP/XU/EW
5 6 7 8
35
 F
E
B
A

D
C

36
B
B

1
1

KEYBOARD UNIT
4.2 KEYBOARD UNIT

2
2

S1813
D1821

D1820

AUDIO
S1816
S1814

D1805 DISP/SCRL
D1813 EJECT TA/AF

D1807
S1811

D1808
S1817 IC1802
S1815 UP
1 2 3 RIGHT
ATT 2 LCD1801
S1827

S1806
3
D1804

S1812
EQ 1

DEH-30MP/XU/EW
D1810
SOURCE

D1812
D1814
C1804 VOLUME 4

S1802

S1807
5

3
3

C1803
D1809
LEFT 5 6
D1806 4
C1812

1 2 3 S1818
D1822

BAND/ESC S1809
D1819

S1804
D1818

S1801 S1810 S1803 S1805 S1808

D1817

D1815
D1816

D1811

FUNC DOWN

4
4

SIDE A
 5 6 7 8

B KEYBOARD UNIT SIDE B

A
R1803

R1809

R1808

IC1801
X1801
D1801

C
D1802

C1802
R1801
R1802

R1834

A CN803
1

D
2
3
CN1801

R1807
4
5

6
7

8 10
9

R1832
E
R1831
C1801

R1835
R1833
R1806

R1805

R1804

R1810

B
DEH-30MP/XU/EW
5 6 7 8
37
 1 2 3 4

4.3 CD CORE UNIT(S10.5COMP1)

C CD CORE UNIT(S10.5COMP1) SIDE A

A
PICKUP UNIT(P10.5)(SERVICE)

A
CN701

REFO1

E
20

HOME

CN901
D

M2
LOADING
/CARRIAGE
MOTOR

M1
E
SPINDLE
MOTOR

IC203 IC301

C
DEH-30MP/XU/EW
38
1 2 3 4
 5 6 7 8

C CD CORE UNIT(S10.5COMP1) SIDE B

A

8EJ
12EJ
B

DSCSNS

C
DEH-30MP/XU/EW
5 6 7 8
39
 1 2 3 4

5. ELECTRICAL PARTS LIST

NOTE:
A
• Parts whose parts numbers are omitted are subject to being not supplied.
• The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
D 801 (B,35,20) Diode DAN202U
Unit Number : YWM5113
Unit Name : Tuner Amp Unit D 802 (B,39,23) Diode DAP202U
D 803 (B,116,30) Diode DAN202U
Unit Number : D 804 (B,115,26) Diode DAP202U
D 805 (B,115,43) Diode DAN202U
C
Unit Name : Keyboard Unit D 806 (B,110,44) Diode DAP202U

Unit Number : CWX3176 D 810 (A,30,23) Diode 1SS133

D 813 (A,27,28) Diode 1SS133
Unit Name : CD Core Unit(S10.5COMP1) D 901 (A,77,115) Diode S5688G
D 902 (A,80,111) Diode S5688G
D 903 (A,70,100) Diode S5688G

A
Unit Number : YWM5113
D
D
904
911
(A,66,100) Diode
(A,24,84) Diode
S5688G
S5688G
D 912 (A,24,78) Diode HZS6L(B2)
Unit Name : Tuner Amp Unit D 931 (A,60,95) Diode HZS7L(C3)
D 932 (A,56,91) Diode HZS7L(A1)
D MISCELLANEOUS
D 951 (B,80,97) Diode DAN202U
IC 151 (B,136,85) IC PML015A L 161 (A,116,85) Inductor LAU2R2K
IC 301 (A,96,137) IC PAL007B L 401 (A,159,91) Inductor LAU1R0K
IC 401 (B,153,28) IC NJM2885DL1-33 L 402 (B,159,96) Inductor LCTAW220J2520
IC 601 (B,88,57) IC PEG159A L 403 (A,158,54) Inductor LAU1R0K
IC 751 (B,124,67) IC NJM4558MD
L 602 (A,99,37) Inductor LAU2R2K
IC 921 (A,10,124) IC NJM2388F84 L 701 (A,64,70) Ferri-Inductor LAU100K
IC 961 (B,67,35) IC BD4843G L 852 (A,50,16) Inductor LAU2R2K
Q 351 (B,163,134) Transistor UMH3N L 901 (A,39,107) Choke Coil 600µH CTH1280
Q 353 (B,141,129) Transistor UMH3N L 951 (A,76,99) Inductor LAU2R2K
Q 401 (B,158,38) Transistor UMH1N
E X 601 (A,76,38) Crystal Resonator 15.000MHz CSS1653
Q 402 (B,158,44) Transistor UMH1N >FU353 (B,134,137) Fuse 3A CEK1286
Q 451 (B,124,116) Transistor DTC124EU > Fuse 10A CEK1208
Q 453 (B,124,122) Transistor UMD2N Z 401 (A,166,99) FM/AM Tuner Unit CWE1951
Q 701 (B,30,54) Transistor UMD2N AR401 (A,175,107) Surge Protector DSP-201M-S00B
Q 702 (A,9,71) Transistor 2SD2396
RESISTORS
Q 841 (B,129,33) Transistor 2SA1036K
Q 842 (B,125,35) Transistor DTC114EU R 151 (B,94,74) RS1/16S102J
Q 851 (B,41,17) Transistor 2SA1036K R 152 (B,94,76) RS1/16S102J
Q 852 (B,51,12) Transistor DTC114EU R 153 (B,94,77) RS1/16S102J
Q 911 (A,9,106) Transistor 2SD2396 R 180 (B,119,98) RS1/16S0R0J
R 301 (B,130,111) RS1/16S471J
F Q 912 (B,21,74) Transistor UMD2N
Q 931 (B,64,92) Transistor UMX1N R 303 (B,129,111) RS1/16S471J
Q 951 (B,84,92) Transistor 2SA1037K R 304 (B,145,111) RS1/16S471J
D 701 (A,25,57) Diode HZS7L(C3) R 306 (B,147,111) RS1/16S471J

DEH-30MP/XU/EW
40
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 309 (A,88,79) RD1/4PU153J R 715 (B,45,56) RS1/16S0R0J
R 351 (B,152,97) RS1/16S821J R 751 (B,118,64) RS1/16S103J

R 352 (B,159,133) RS1/16S0R0J R 752 (B,118,69) RS1/16S103J A

R 355 (B,141,126) RS1/16S821J R 753 (B,113,74) RS1/16S103J
R 356 (B,137,103) RS1/16S821J R 754 (B,122,72) RS1/16S103J
R 358 (B,135,133) RS1/16S821J R 755 (B,116,74) RS1/16S103J
R 359 (B,146,133) RS1/16S223J R 756 (B,129,67) RS1/16S103J

R 360 (B,166,139) RS1/16S223J R 757 (B,116,75) RS1/16S103J

R 363 (B,138,133) RS1/16S223J R 758 (B,110,75) RS1/16S103J
R 364 (B,140,133) RS1/16S223J R 759 (B,113,75) RS1/16S103J
R 381 (B,137,129) RS1/16S0R0J R 760 (B,123,79) RS1/16S103J
R 382 (B,145,129) RS1/16S0R0J R 761 (B,126,62) RS1/16S0R0J

R 386 (B,166,136) RS1/16S0R0J R 762 (B,119,78) RS1/16S0R0J

R 401 (B,160,60) RS1/16S681J R 803 (B,117,45) RS1/16S473J B
R 402 (B,160,76) RS1/16S681J R 804 (B,116,24) RS1/16S222J
R 403 (B,160,78) RS1/16S681J R 805 (B,106,25) RS1/16S222J
R 404 (B,160,81) RS1/16S681J R 806 (A,91,16) RD1/4PU222J

R 405 (B,160,83) RS1/16S681J R 807 (B,86,15) RS1/16S222J

R 406 (B,160,85) RS1/16S681J R 808 (B,34,24) RS1/16S104J
R 407 (B,160,87) RS1/16S102J R 809 (B,142,39) RS1/16S222J
R 408 (B,144,42) RS1/16S223J R 810 (B,34,22) RS1/16S103J
R 409 (B,117,56) RS1/16S223J R 811 (B,93,31) RS1/16S473J

R 410 (B,145,46) RS1/16S223J R 813 (B,111,28) RS1/16S104J

R 411 (B,145,42) RS1/16S223J R 814 (B,96,31) RS1/16S102J
R 413 (B,157,34) RS1/16S221J R 815 (B,108,27) RS1/16S102J C
R 414 (A,138,38) RD1/4PU1R8J R 816 (B,123,26) RS1/16S1R0J
R 415 (B,158,40) RS1/16S221J R 822 (B,46,70) RS1/16S102J

R 421 (B,157,77) RS1/16S0R0J R 823 (B,46,71) RS1/16S102J

R 451 (B,125,113) RS1/16S103J R 824 (B,115,50) RS1/16S102J
R 452 (B,125,125) RS1/16S221J R 825 (B,29,21) RS1/16S102J
R 453 (B,124,119) RS1/16S153J R 826 (B,121,25) RS1/16S0R0J
R 454 (A,120,119) RD1/4PU102J R 841 (B,130,29) RS1/16S103J

R 602 (B,72,41) RS1/16S103J R 842 (B,128,28) RS1/16S222J

R 603 (B,94,80) RS1/16S103J R 851 (B,34,17) RS1/16S153J
R 604 (B,100,63) RS1/16S681J R 852 (B,43,14) RS1/16S153J
R 605 (B,158,60) RS1/16S681J R 853 (B,119,17) RS1/16S222J D
R 606 (B,107,43) RS1/16S103J R 911 (B,21,71) RS1/16S223J

R 607 (B,147,55) RS1/16S681J R 912 (A,24,81) RD1/4PU152J

R 610 (B,104,54) RS1/16S473J R 922 (B,14,117) RS1/16S473J
R 612 (B,101,74) RS1/16S103J R 931 (B,63,56) RS1/16S104J
R 613 (B,100,76) RS1/16S103J R 932 (B,57,57) RS1/16S104J
R 615 (B,70,64) RS1/16S0R0J R 933 (B,64,94) RS1/16S104J

R 616 (B,61,36) RS1/16S473J R 934 (B,64,96) RS1/16S473J

R 619 (B,116,54) RS1/16S0R0J R 935 (B,60,91) RS1/16S473J
R 620 (B,96,66) RS1/16S0R0J R 936 (B,64,97) RS1/16S473J
R 621 (B,18,145) RS1/16S102J R 937 (B,65,122) RS1/16S473J
E
R 622 (B,16,142) RS1/16S102J R 938 (B,63,127) RS1/4SA102J

R 701 (A,20,54) RD1/4PU271J R 951 (B,77,90) RS1/16S473J

R 702 (A,20,61) RD1/4PU121J R 952 (B,81,89) RS1/16S102J
R 703 (B,57,54) RS1/16S682J R 953 (B,88,94) RS1/16S472J
R 704 (B,54,42) RS1/16S682J R 954 (B,89,96) RS1/16S472J
R 705 (B,57,51) RS1/16S682J R 955 (A,71,110) RD1/4PU153J

R 706 (B,57,48) RS1/16S682J R 961 (B,73,35) RS1/16S102J

R 707 (B,45,52) RS1/16S104J R 962 (B,64,38) RS1/16S822J
R 708 (B,57,47) RS1/16S221J
R 709 (B,48,47) RS1/16S221J CAPACITORS
R 710 (B,57,50) RS1/16S221J F
C 153 (B,163,71) CKSRYB224K16
R 711 (B,52,42) RS1/16S221J C 154 (B,133,67) CKSRYB474K10
R 712 (B,57,53) RS1/16S221J C 155 (B,160,69) CKSRYB224K16
R 713 (B,61,34) RS1/16S102J
DEH-30MP/XU/EW
5 6 7 8
41
 1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 156 (B,126,79) CKSRYB474K10 C 923 (A,18,120) CEJQ101M16
C 159 (B,126,89) CKSRYB153K50 C 924 (B,19,116) CKSRYB103K50

A C 160 (A,122,89) CEJQ100M16 C 961 (B,70,34) CKSRYB473K25

C 161 (B,139,97) CKSRYB153K50 C 962 (A,67,39) CEJQ100M16
C 162 (A,116,95) CEJQ470M10
C
C
163
165
(B,125,87)
(A,136,97)
CKSRYB104K25
CEJQ100M16 B
Unit Number :
C 305 (A,128,119) CFTNA224J50
C 306 (A,143,119) CFTNA224J50
Unit Name : Keyboard Unit
C 307 (A,133,119) CFTNA224J50
C 308 (A,138,119) CFTNA224J50 MISCELLANEOUS
C 309 (B,127,146) CKSQYB225K10
IC 1801 (B,24,94) IC PD6340A
C 310 (B,132,137) CKSQYB225K10 IC 1802 (A,14,23) IC TSOP4840SB1
B C 311 (A,107,128) CEJQ100M16 D 1801 (B,28,81) Diode DAN202U
C 313 (A,54,125) 3300µF/16V CCH1494 D 1802 (B,29,78) Diode DAP202U
C 351 (A,129,96) CEJQ2R2M50 D 1804 (A,20,135) LED CL-490S-WK-SD
C 352 (A,142,96) CEJQ2R2M50
D 1805 (A,5,4) LED SML-310VT
C 355 (A,127,104) CEJQ2R2M50 D 1806 (A,29,5) LED SML-310VT
C 356 (A,148,104) CEJQ2R2M50 D 1807 (A,10,10) LED SML-310VT
C 357 (B,147,133) CKSRYB222K50 D 1808 (A,11,18) LED SML-310VT
C 358 (B,164,139) CKSRYB222K50 D 1809 (A,27,18) LED CL-190UB2-X
C 401 (A,152,53) CEJQ470M6R3
D 1810 (A,20,15) LED CL-190UB2-X
C 402 (B,155,51) CKSRYB103K50 D 1811 (A,33,38) LED SML-310VT
C 403 (B,151,34) CKSRYB103K50 D 1812 (A,22,28) LED SML-310VT
C C 404 (B,144,26) CKSYB475K10 D 1813 (A,11,39) LED SML-310VT
C 405 (A,154,87) CEJQ101M10 D 1814 (A,22,50) LED SML-310VT
C 406 (B,170,91) CKSRYB104K25
D 1815 (A,32,69) LED SML-310VT
C 407 (B,166,66) CKSRYB103K50 D 1816 (A,32,79) LED SML-310VT
C 408 (A,142,32) CEJQ220M16 D 1817 (A,32,89) LED SML-310VT
C 451 (A,124,127) CEJQ330M10 D 1818 (A,31,99) LED SML-310VT
C 601 (B,76,43) CCSRCH180J50 D 1819 (A,31,110) LED SML-310VT
C 602 (B,81,43) CCSRCH200J50
D 1820 (A,6,121) LED SML-310VT
C 604 (B,97,42) CKSRYB104K16 D 1821 (A,6,132) LED SML-310VT
C 605 (A,100,42) CEJQ100M16 D 1822 (A,30,120) LED SML-310VT
C 606 (B,74,32) CKSRYB104K16 X 1801 (B,29,85) Ceramic Resonator 5.00MHz CSS1547
D C 607 (A,76,30) CEJQ100M16 S 1801 (A,32,5) Push Switch CSG1155
C 609 (B,147,52) CCSRCH470J50
S 1802 (A,27,21) Push Switch CSG1155
C 701 (B,31,51) CKSRYB473K25 S 1803 (A,32,65) Push Switch CSG1155
C 703 (A,34,35) 470µF/16V CCH1331 S 1804 (A,31,97) Push Switch CSG1155
C 704 (B,145,77) CKSRYB105K10 S 1805 (A,32,75) Push Switch CSG1155
C 705 (B,134,70) CKSRYB105K10 S 1806 (A,18,50) Push Switch CSG1155
C 751 (B,116,64) CCSRCH101J50
S 1807 (A,26,27) Push Switch CSG1155
C 752 (B,113,69) CKSRYB105K10 S 1808 (A,32,86) Push Switch CSG1155
C 753 (B,113,72) CCSRCH101J50 S 1809 (A,31,107) Push Switch CSG1155
C 754 (B,116,72) CCSRCH101J50 S 1810 (A,32,42) Push Switch CSG1155
C 755 (B,131,67) CCSRCH101J50 S 1811 (A,11,35) Push Switch CSG1155
E
C 756 (B,122,71) CKSRYB105K10
S 1812 (A,21,18) Push Switch CSG1155
C 757 (B,116,77) CKSRYB474K10 S 1813 (A,3,5) Push Switch CSG1155
C 758 (B,107,81) CKSRYB474K10 S 1814 (A,5,130) Push Switch CSG1155
C 759 (B,113,76) CKSRYB474K10 S 1815 (A,15,18) Push Switch CSG1155
C 760 (B,121,78) CKSRYB474K10 S 1816 (A,5,123) Push Switch CSG1155
C 761 (A,107,86) CEJQR47M50
S 1817 (A,14,10) Push Switch CSG1155
C 762 (A,115,70) CEJQ101M10 S 1818 (A,32,86) Push Switch CSG1155
C 851 (B,48,14) CKSRYB104K16 S 1827 (A,31,118) Encoder(SOURCE,VOLUME) YSD5005
C 901 (B,57,121) CKSRYB104K50 LCD1801 (A,15,95) LCD YAW5064
C 911 (A,32,59) CEJQ470M10
F C 912 (B,25,75) CKSRYB103K50 RESISTORS
C 913 (A,25,68) 470µF/16V CCH1331 R 1801 (B,28,73) RS1/16S222J
C 921 (B,19,108) CKSRYB103K50 R 1802 (B,29,73) RS1/16S222J
C 922 (A,20,104) CEJQ221M10 R 1803 (B,20,130) RS1/4SA561J
DEH-30MP/XU/EW
42
1 2 3 4
 5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 1804 (B,16,16) RS1/4SA102J R 248 (B,55,74) RS1/16SS105J
R 1805 (B,20,16) RS1/4SA561J R 307 (A,19,20) RS1/16SS183J
R 308 (A,17,20) RS1/16SS183J
R 1806 (B,25,16) RS1/4SA821J R 309 (A,18,18) RS1/16SS183J A
R 1807 (B,20,50) RS1/4SA821J R 310 (A,17,16) RS1/16SS183J
R 1808 (B,5,124) RS1/4SA821J
R 1809 (B,5,127) RS1/4SA821J R 601 (B,30,47) RS1/16S101J
R 1810 (B,12,16) RS1/4SA102J R 602 (B,28,50) RS1/16S101J
R 606 (B,20,54) RS1/16S0R0J
R 1831 (B,28,28) RS1/16S472J R 701 (B,26,44) RS1/16SS221J
R 1832 (B,28,29) RS1/16S472J R 707 (B,32,45) RS1/16SS473J
R 1833 (B,26,21) RS1/16S2R2J
R 1835 (B,27,23) RS1/16S121J R 709 (A,36,35) RS1/16SS222J
R 710 (B,41,46) RS1/16SS102J
CAPACITORS R 712 (A,45,57) RS1/16SS222J
R 713 (B,40,57) RS1/16SS222J
R 716 (B,29,37) RS1/16SS472J B
C 1801 (B,26,25) CKSRYB474K10
C 1802 (B,26,75) CKSRYB104K16
C 1803 (A,27,15) CKSRYF104Z25 R 724 (B,31,36) RS1/16S473J
C 1804 (A,25,14) CKSRYF104Z25 R 726 (B,23,47) RS1/16SS103J
C 1812 (A,31,132) CKSRYF104Z25 R 727 (B,31,42) RS1/16SS473J
R 729 (B,20,48) RS1/16SS223J

C
R 730 (B,20,46) RS1/16SS473J

Unit Number : CWX3176 R 740 (A,38,59) RS1/16SS222J

R 746 (A,13,38) RS1/16SS104J
Unit Name : CD Core Unit(S10.5COMP1) R 750 (A,40,66) RS1/16SS473J
R 902 (A,20,36) RS1/16SS221J
MISCELLANEOUS R 905 (A,21,36) RS1/16SS221J
C
IC 201 (B,39,70) IC UPD63763CGJ R 906 (B,20,36) RS1/16SS221J
IC 203 (A,12,16) IC NJM2886DL3-33 R 907 (B,16,62) RS1/16SS0R0J
IC 301 (A,28,18) IC BA5835FP R 908 (B,16,64) RS1/16SS0R0J
IC 701 (A,32,48) IC PE5505A R 911 (B,20,32) RS1/16SS0R0J
Q 101 (B,60,89) Transistor 2SA1577
CAPACITORS
Q 701 (B,24,41) Transistor UN2111
X 201 (B,28,57) Ceramic Resonator 16.934MHz CSS1603 C 103 (B,57,83) CEVW101M16
X 701 (A,24,37) Ceramic Resonator 4.000MHz CSS1652 C 108 (A,47,66) CKSSYB104K10
S 901 (A,57,57) Switch(HOME) CSN1067 C 201 (B,46,56) CKSSYB102K50
S 903 (B,23,78) Switch(DSCSNS) CSN1067 C 202 (B,47,58) CKSSYB104K10
C 204 (B,35,48) CEVW220M6R3
S 904 (B,42,87) Switch(12EJ) CSN1068 D
S 905 (B,28,88) Switch(8EJ) CSN1068 C 205 (A,34,63) CKSSYB104K10
C 208 (B,34,54) CKSSYB104K10
RESISTORS C 209 (B,31,57) CKSSYB104K10
C 210 (A,31,66) CKSRYB105K10
R 101 (B,61,92) RS1/10SR2R4J C 216 (B,53,77) CKSSYB332K50
R 102 (B,63,92) RS1/10SR2R4J
R 103 (B,63,89) RS1/10SR2R7J C 217 (B,52,79) CKSSYB104K10
R 104 (A,52,73) RS1/16SS102J C 218 (B,52,76) CKSSYB473K10
R 201 (B,44,57) RS1/16SS102J C 219 (B,52,74) CKSSYB104K10
C 220 (A,46,77) CKSSYB182K50
R 202 (A,38,62) RS1/16SS473J C 221 (B,51,74) CKSSYB104K10
R 203 (A,37,62) RS1/16SS473J E
R 214 (A,46,79) RS1/16SS472J C 222 (A,46,73) CCSSCH560J50
R 216 (A,46,81) RS1/16SS472J C 223 (A,44,74) CCSSCH4R0C50
R 221 (A,44,81) RS1/16SS103J C 224 (B,52,68) CKSSYB104K10
C 225 (A,47,67) CKSSYB103K16
R 222 (A,45,81) RS1/16SS103J C 226 (A,49,67) CCSSCH680J50
R 225 (B,52,78) RS1/16SS103J
R 226 (B,52,77) RS1/16SS393J C 227 (A,48,65) CCSSCH470J50
R 227 (A,44,75) RS1/16SS562J C 228 (A,46,62) CKSSYB103K16
R 228 (A,46,72) RS1/16SS122J C 232 (A,12,31) CKSRYB105K10
C 237 (A,31,67) CKSSYB104K10
R 229 (A,44,72) RS1/16SS472J C 239 (A,46,74) CCSSCH220J50
R 232 (A,46,75) RS1/16SS122J
R 241 (B,26,63) RS1/16SS333J C 246 (A,42,80) CKSSYB104K10 F
R 243 (B,26,62) RS1/16SS333J C 250 (A,42,81) CKSRYB102K50
R 245 (B,26,69) RS1/16SS333J C 251 (A,41,83) CKSRYB102K50
C 303 (A,18,20) CKSSYB472K25

DEH-30MP/XU/EW
5 6 7 8
43
 1 2 3 4

Circuit Symbol and No. Part No.

C 304 (A,17,17) CKSSYB103K16

C 307 (A,34,15) CKSSYB104K10

A C 308 (A,17,30) CKSRYB105K10
C 601 (B,25,50) CCSRCH102J50
C 602 (B,26,51) CCSRCH102J50
C 701 (B,25,47) CKSSYB104K10

C 703 (B,28,42) CKSSYB103K16

C 706 (B,34,43) CKSSYB104K10
C 707 (A,36,57) CKSSYB104K10
C 714 (A,24,41) CKSSYB104K10
C 722 (B,29,45) CKSQYB475K6R3

C 903 (B,14,54) CKSSYB471K50

C 907 (B,14,62) CKSSYB103K16
B
Miscellaneous Parts List
Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXC4166
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-30MP/XU/EW
44
1 2 3 4
 5 6 7 8

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

• In this product the single voltage (3.3V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus B
probe for CH1 to the GND. search, turn off the power immediately to protect the
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0dB,
and the auto-adjustment values are reset to the default
• For stable circuit operation, keep the mechanism settings.
operating for about one minute or more after the C
regulator is turned on.

• In the test mode, any software protections will not

work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

• The RFI and RFO signals with a wide frequency range

are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

• The load and eject operation is not guarantied with the

D
mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

DEH-30MP/XU/EW
5 6 7 8
45
 1 2 3 4

- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In

A Display

[CD] or [SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]

Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

[BAND] [3] [6] [1] [>] [<] [2]

[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
B S curve check *2 Close *8 *8 switching *3 Gop Mode *10
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL

[BAND] [1] [6] [3] [>] [<] [2]

Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] *5 [>] [<] [2]

Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

C *6

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X

or 9X 9X 9X

*1) TYP → + 6 dB → + 12 dB Operation

TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [Key] Test Mode
[BAND] Power On/Off
[>] CRG + / TR Jump +
*2) Focus Close → S Curve check setting → F EQ measurement setting (Direction of the external surface)
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 [<] CRG - / TR Jump -
(TRK99MIN99SEC99) (Direction of the internal surface)
D
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the [2] RF Gain switching / Offset adjustment display /
order of the original display
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
*4) 1TR/4TR/10TR/32TR/100TR F,T,RF AGC
*5) Single → 4TR → 10TR → 32TR → 100TR → CRG Move [4] SPDL 1X/2X switching
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) As for the double speed(2x), audio output cannot be
supported.
*6) Only at the time of CRG move, 100TR jump [5] Error Rate measurement
ON : ERR 30Counts Start
BER display data[%]
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
E [6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*8) CRG motor voltage = 2 [V]

*9) TYP (1X) → 2X → 1X *10) OFF(TYP) → FORCUS → TRACKING

TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

• As for the double speed (2x), audio output cannot be supported

*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
F • In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.

DEH-30MP/XU/EW
46
1 2 3 4
 5 6 7 8

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • TCD-782
• Mode • TEST MODE

CD CORE UNIT(S10.5COMP1)
C

L.P.F.
REFO1
E Xch Ych
E 100kΩ
F
Oscilloscope
VREF 390pF

F 100kΩ

VREF 390pF

L.P.F. D

• Checking Procedure
1. In test mode, load the disc and switch the 3V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-30MP/XU/EW
5 6 7 8
47
 1 2 3 4

Grating waveform Ech → Xch 20mV/div, AC

Fch → Ych 20mV/div, AC
A
0° 30°

45° 60°

75° 90°

DEH-30MP/XU/EW
48
1 2 3 4
 5 6 7 8

6.3 ERROR MODE

- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of A
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method

1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

2) Head unit display examples

B
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.

8-digit display 6-digit display 4-digit display

ERROR–xx ERR–xx E–xx

(2) Error Code List

Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error → Failure on home switch or CRG move mechanism. C
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
→ Damages or stains on disc, or excessive vibrations on REWRITABLE. D

30 Electricity Search Time Out Failed to reach target address.

→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). E
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-30MP/XU/EW
5 6 7 8
49
 1 2 3 4

7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A

- Removing the Case (not shown)

1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1) CD Mechanism Module

1 Remove the four screws.

B
Disconnect the connector and then remove the 1
CD Mechanism Module.
1

- Removing the Grille Assy (Fig.1)

2 Release the two latchs and then remove

the Grille Assy.
1
C
2 1 2

Grille Assy Fig.1

- Removing the Tuner Amp Unit (Fig.2)

1 Remove the screw.

2
2
D 2
2 Remove the three screws.

3 Straighten the tabs at three locations

indicated.

4 Remove the screw and then remove 4

the Tuner Amp Unit. 1

3 3 3

Tuner Amp Unit

Fig.2
F

DEH-30MP/XU/EW
50
1 2 3 4
 5 6 7 8

- How to hold the Mechanism Unit

1. Hold the Upper and Lower Frames.
2. Do not hold the front portion of the Upper
Frame, because it is not very solid. A

Do not squeeze this area.

- Removing the Upper and Lower Frames

1. With a disc inserted and clamped in the a
B
mechanism, remove the two Springs (A), Upper Frame
the six Springs (B), and the four Screws. B
2. Turn the Upper Frame using the part "a" as
a pivot, and remove the Upper Frame. C
3. While lifting the Carriage Mechanism,
B
remove it from the three Dampers.
Caution: When assembling, be sure to apply
some alcohol to the Dampers and assemble B
the mechanism in a clamped state.

B
B

A
Damper
Damper D
A
Carriage Mechanism Lower Frame

DEH-30MP/XU/EW
5 6 7 8
51
 1 2 3 4

- How to remove the CD Core Unit

1. Apply Shorting Solder to the flexible cable of Shorting Solder
the Pickup, and disconnect it from the
A connector.
2. Unsolder the four leads, and loosen the
Screw.
3. Remove the CD Core Unit.
Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state
so as not to damage it.

Screw

B
CD Core Unit

Solder

- How to remove the Pickup Unit

1. Make the system in the carriage mechanism mode, and have it clamped.
2. Remove the CD Core Unit and remove the leads from the Inner Holder.
3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.
C 4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw.
Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load
Carriage Motor Assy, do not make them loose over the Feed Screw.

Poly Washer Change Arm

Pickup Lock Arm

Inner Holder
Feed Screw

Planet Gear
Pickup Rack

Chassis

Pickup

DEH-30MP/XU/EW
52
1 2 3 4
 5 6 7 8
7.1.2 CONNECTOR FUNCTION DESCRIPTION

1 3 5 7 9 11 13 15
2 4 6 8 10 12 14 16

POWER SUPPLY B
PRE-FRONT SPEAKER OUTPUT WIRED
OUTPUT
REMOTE
PRE-SUB WOOFER CONTROL
OUTPUT AUX IN

ANTENNA JACK

POWER SUPPLY, SPEAKER OUTPUT

Pin No. Pin No.
1 FR+ 9 MUTE
2 RR+ 10 NC C
3 FR- 11 B.REM
4 RR- 12 NC
5 FL+ 13 NC
6 RL+ 14 ACC
7 FL- 15 GND
8 RL- 16 B.UP

DEH-30MP/XU/EW
5 6 7 8
53
 1 2 3 4

7.2 PARTS
7.2.1 IC
- Pin Functions(PEG159A)
A Pin No. Pin Name I/O Function and Operation
1 ILMPW O Illumination output
2 ejtin I Eject key input
3,4 ROT1,2 I Rotary encoder pulse input
5 NC Not used
6 FLPILM O Flap illumination output
7 SWVDD GRILLE : Chip enable output
8 BYTE I External data bus width change input
9 CNVSS I Processor mode change input
10,11 NC Not used
12 reset I Reset input
13 XOUT O Crystal oscillating element connection output
B 14 VSS GND
15 XIN I Crystal oscillating element connection input
16 VCC Power supply
17 NMI I NMI input
18 dsens I Detach sense input
19 bsens I Back up sense input
20 asens I ACC sense input
21 CDRST O CD Mechanism Module : Reset output
22 NC Not used
23 brst O P-BUS : Reset output
24 BRXEN I/O P-BUS : Reception enable input/output
25 bsrq I P-BUS : Request input
C 26 PEE O PEE sound output
27 RX2 I IP-BUS : Data input 2
28 NC Not used
29 RX I IP-BUS : Data input
30 TX O IP-BUS : Data output
31 BSO O CD Mechanism Module : Serial data output
32 BSI I CD Mechanism Module : Serial data input
33 BSCK O CD Mechanism Module : Clock output
34 KEYD I Key data input
35 DPDT O GRILLE : Data output
36 KYDT I GRILLE : Data input
37 ANTPW O Antenna power output
D 38 TELIN I TEL mute input
39 PCL O Output for clock adjustment
40 ASENBO O IP-BUS : Slave ACC sense output
41-46 NC Not used
47 DALMON O For consumption low-current output
48 SYSPW O System power control output
49-51 NC Not used
52 IPPW O IP-BUS : Driver power supply control output
53 MUTE O Mute output
54 VST O E.VOL : Strobe output
55 VCK O E.VOL : Clock output
56 VDT O E.VOL : Data output
E 57 NC Not used
58 ROMDATA Not used
59 ROMCK Not used
60 ROMCS Not used
61 NC Not used
62 VCC Power supply
63 NC Not used
64 VSS GND
65 TUNPCE2 O TUNER : Chip enable output(EEPROM)
66 TUNPCE1 O TUNER : Chip enable output(PLL)
67 TPCK O TUNER : Clock output(PLL)
68 TPDI I TUNER : Data input(PLL)
F
69-73 NC Not used
74 RCK I RDS : Clock input
75 LDET I RDS : PLL lock sense input

DEH-30MP/XU/EW
54
1 2 3 4
 5 6 7 8

Pin No. Pin Name I/O Function and Operation

76-80 NC Not used
81 RDSLOCK I RDS : Lock signal
g input A
82 RDSDT I RDS : Data input
83 RDS57K I RDS : 57kHz count pulse input
84 NC Not used
85 RECIVE O Not used
86 TPDO O TUNER : Data output(PLL)
87 NC Not used
88 TESTIN I Test program input
89-91 NC Not used
92 SSENS I Source key sense input
88 CSENS I Flap close sense input
88 KEYAD I Wired remote control analog input
95 MODEL I Model detect input B
96 AVSS Analog GND
97 SL I Signal level input
98 VREF Reference voltage
99 AVCC Analog power supply
100 NC Not used

* PEG159A IC's marked by * are MOS type.

Be careful in handling them because they are very
30 1 liable to be damaged by electrostatic induction.
31
100
C

50 81

51 80
D

BD4843G
N.C.

N.C.

5 4

Vref

1 2 3
VOUT

VDD

GND

DEH-30MP/XU/EW
5 6 7 8
55
 1 2 3 4

PAL007B

sw_vcc
Protector;
Over voltage
TAB

1
Reference
amp_vcc

P-GND2 Stand-by

2
Circuit

+-
OUT2-
3

Offset Protector;
STBY
4

Detection Thermal

-+
OUT2+
5

VCC
6

+-
OUT1-
7

Offset
P-GND1
8

Detection

-+
OUT1+
9
10

SVR
11

IN1
C
12

IN2

amp_vcc
13

Protector;
S-GND Short circuit
14

IN4
15

IN3
16

AC-GND
17

+-

OUT3+
D Offset
18

P-GND3 Detection
19

-+

OUT3-
20

VCC
21

+-

OUT4+
Offset
22

MUTE Detection
23

-+

OUT4-
24

E P-GND4
25

SWITCH
sw_vcc
stby

Protector;
Over current limit

Mute circuit

DEH-30MP/XU/EW
56
1 2 3 4
 LM_out
DATA
CLK
STB
Vcc
Vref
GND
PML015A

Level Meter Supply

5

Digital

5
IN1_L Vp
Block & Pref
IN2_L
Reference PGND
IN3_L
- Block Diagram

IN4+_L
Isolator
IN4-_L Gain Auto Primary
Adjuster Zero Pre/SW_L
IN4-_R Volume
Isolator

Input Selector
IN4+_R Anti- Secondary
IN3_R Radiation
Filter Volume
IN2_R
IN1_R Anti-Alias
Pre/SW_R

Phase inv.
Filter
Secondary
Front_L
Volume

LPF

6
6

FIE_L
Secondary

Volume FIE Rear_L

TRE MID BASS

Secondary
Anti- Front_R
LOUDNESS HPF Radiation Volume

Filter FIE_R
Secondary FIE Rear_R

DEH-30MP/XU/EW
Volume

7
7

Soft step Blocks ( M.S. M.S.S. )

Vref 9
Vcc 8
Rear_L 7
Front_L 6
IN4-_L 5
IN4+_L 4
IN3_L 3
IN2_L 2
IN1_L 1

Pref 14
Vp 13
Pre/SW_L 12
FIE_L 11
GND 10
- Pin Layout
8

8
20 CLK
21 STB

19 DATA

16 LMout
18 FIE_R
26 IN3_R
27 IN2_R
28 IN1_R

15 PGND
24 IN4-_R
25 IN4+_R

22 Rear_R
23 Front_R

17 Pre/SW_R

57
E
A

D
C

F
B
 1 2 3 4

- Pin Functions(PD6340A)
Pin No. Pin Name I/O Function and Operation
A 1-5 SEG4-0 O LCD segment output
6-9 COM3-0 O LCD common output
10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output
15,16 KDT0,1 I Key data input (analogue input)
17 REW I Remote control reception input
18 DPDT I Display data input
19 NC Not used
20 KYDT O Key data output
21 MODA GND
22 X0 Crystal oscillator connection pin
23 X1 Crystal oscillator connection pin
B 24 VSS GND
25,26 KDT2,3 I Key data input
27 NC Not used
28 KST4 O Key strobe output
29-32 NC Not used
33-55 SEG35-13 O LCD segment output
56 VDD Power supply
57-64 SEG12-5 O LCD segment output

* PD6340A
1

16

C
64 17

49 32
48

D
33

NJM2886DL3-33

Thermal
Protection

E Bandgap
Reference
-+

1 2 3 4 5
F
CONTROL VIN GND VO NC

DEH-30MP/XU/EW
58
1 2 3 4
 5 6 7 8

- Pin Functions (UPD63763CGJ)

Pin No. Pin Name I/O Function and Operation
1 D.VDD Power supply for digital circuits
2 D1.GND Ground for 1.6 V digital circuits A
3 reset I Input of reset
4-8 AB12-8 I Address bus 12-8 from the microcomputer
9-16 AD7-0 I/O Address/data bus 7-0 to the microcomputer
17 cs I Chip selection
18 ASTB I Address strobe
19 read I Control signals(read)
20 write I Control signals(write)
21 wait O Control signals(wait)
22 INTQ O Interruption signals to the external microcomputer
23,24 IFMODE0,1 I Switching the microcomputer I/F 0, 1
25 D1.VDD Power supply for 1.6 V digital circuits
B
26 DA.VDD Power supply for DAC
27 ROUT O Output of audio for the right channel
28 DA.GND Ground for DAC
29 REGC Connected to the capacitor for band gap
30 DA.GND Ground for DAC
31 LOUT O Output of audio for the left channel
32 DA.VDD Power supply for DAC
33 X.VDD Power supply for the crystal oscillator
34 XTAL I Connected to the crystal oscillator(16.9344 MHz)
35 xtal O Connected to the crystal oscillator(16.9344 MHz)
36 X.GND Ground for the crystal oscillator
37 VDDREG15 Control of 1.6 V regulator C
38 PWMSW0 I Setup 0 for PWM output(SD, MD)
39-41 TEST3-1 I Connected to Ground
42 PWMSW1 I Setup 1 for PWM output(FD, TD)
43 TESTEN I Connected to Ground
44 D1.GND Ground for 1.6 V digital circuits
45 DIN I Input of audio data
46 DOUT O Output of audio data
47 SCKIN I Clock input for audio data
48 SCKO O Clock output for audio data
49 LRCKIN I Input of LRCK for audio data
50 LRCK O Output LRCK for audio data
51 xtalen I Permission to oscillate 16.9344 MHz D
52 D1.VDD Power supply for 1.6 V digital circuits
53 RFCK/HOLD O Output of RFCK/HOLD signal
54 WFCK/MIRR O Output of WFCK/MIRR signal
55 PLCK/RFOK O Output of PLCK/Output of RFOK
56 LOCK/RFOK O Output of LRCK/Output of RFOK
57 C1D1/C8M/(RA13) O Information on error correction/C8M : 8 MHz
58 C1D2/C16M/(RA12) O Information on error correction/C16M : 16 MHz
59 C2D1/RMUTE O Information on error correction/Mute for Rch
60 C2D2/LMUTE O Information on error correction/Mute for Lch
61 C2D3/SHOCK O Information on error correction/Detection of vibration
62 D1.GND Ground for 1.6 V digital circuits
63 C33M O Output of 33.8688 MHz(CLK for SDRAM) E
64 (rcs) O DRAM cs
65 RA11 O Output of DRAM address 11
66 (CKE) O Output of DRAM CKE
67 ras O Output of DRAM ras
68 cas)(LDQM) O Output of DRAM lower cas(LDQM)
69 cas!(UDQM) O Output of DRAM upper cas(UDQM)

DEH-30MP/XU/EW
5 6 7 8
59
 1 2 3 4

Pin No. Pin Name I/O Function and Operation

70 we O Output of DRAM we
71 oe(cas) O Output of DRAM oe(cas)
A 72 D.GND Ground for digital circuits
73-88 RDB0-15 I/O Input/output of DRAM data0-15
89-99 RA0-10 O Output of DRAM address0-10
100 D.VDD Power supply for digital circuits
101 FD+ O Output of focus drive PWM +
102 FD- O Output of focus drive PWM -
103 TD+ O Output of tracking drive PWM +
104 TD- O Output of tracking drive PWM -
105 SD+ O Output of thread drive PWM +
106 SD- O Output of thread drive PWM -
107 MD+ O Output of spindle drive PWM +
108 MD- O Output of spindle drive PWM -
B
109 REFOUTSV O REFOUT for servo
110 AD.VDD Power supply for ADC
111 EFM O Output of EFM signals
112 ASY I Input of asymmetry
113 ATEST O Analog tests
114 RFI I Input of RF
115 AD.GND Ground for the analog system
116 AGCO O Output of RF
117 C3T O Connection to the capacitor for detecting 3T
118 AGCI I Input of AGC
119 RFO O Output of RF(AGC)
C 120,121 EQ2,1 I Equalizer 2, 1
122 RF2- I Reversal input of RF2
123 RF- I Reversal input of RF
124 A.GND Ground for the analog system
125 A I Input of A
126 C I Input of C
127 B I Input of B
128 D I Input of D
129 F I Input of F
130 E I Input of E
131 VREFIN I Input of reference voltage
132 A.VDD Power supply for the analog system
D 133 REFOUT O Output of reference voltage
134 REFC I Connected to the capacitor for output of REFOUT
135 FE- I Reversal input of FE
136 FEO O Output of FE
137 ADIN I Input of FE, TE A/D converter
138 TE- I Reversal input of TE
139 TEO O Output of TE
140 TE2 O TE2
141 TEC I TEC
142 LD O Output of LD
143 PD I Input of PD
144 D.GND Ground for digital circuits
E

* UPD63763CGJ
109
144

1 108

36 73
F
37

72

DEH-30MP/XU/EW
60
1 2 3 4
 5 6 7 8

- Pin Functions (PE5505A)

Pin No. Pin Name I/O Format Function and Operation
1 AVREF A power supply / Positive power supply(5V)
2 AVSS A power supply GND A
3 testin I Chip check test program starting input
4 CLAMP Not used
5 EVDD E power supply / Positive power supply
6 FMODE For flash rewriting / L : flash rewriting mode
7 FLRQ For flash rewriting / Reset voltage control
8 IC/FLMD0 IC : VSS direct connection/FLMOD0 : Pull-down
9 VDD Positive power supply(5V)
10 REGC Connected to the capacity stabilizing output of the regulator
11 VSS GND
12 X1 I Oscillator connection for mainclock
13 X2 Oscillator connection for mainclock
B
14 reset I System reset input
15 XT1 I Connected to the oscillator for subclock(connected to VSS via the resistor)
16 XT2 Connected to the oscillator for subclock(Open)
17 PULLDOWN I Connected to EVDD or EVSS via the resistor
18 ejsw Not used
19 xint I C CD LSI interruption signal input
20 NC Not used
21 brst I Bus reset input
22 BSI I Bus serial data input
23 BSO O C Bus serial data output
24 bsck I/O /C Bus serial clock input/output
25 FTxD O C For flash rewriting(transmitted signal) C
26 FRxD I For flash rewriting(received signal)
27 BRXEN I/O /C Bus RX enable input/output
28 bsrq I/O /C Bus serial clock input/output
29 dspok Not used
30 DSCSNS I C Disc state sense input
31 8EJ(S905) I C input of detection of 8 cm disc ejection
32 12EJ(S904) I C input of detection of 12 cm disc ejection
33 EVSS E power supply GND
34 EVDD E power supply / Positive power supply
35,36 SRAMLEVEL0,1 O SRAM level meter output
37 EMPH O C Emphasis information output
38 emph Not used D
39 CDMUTE Not used
40 LOEJ Not used
41 CLCONT O Driver input switching output
42 HOME I Home SW sense input
43 adena O C A/D reference voltage supply control output
44 LRCKOK O C (DOUT mute output)
45 SRAMLEVEL2 O C SRAM level meter output
46 CD3VON(MCKRQ) O C CD + 3.3 V power supply control output(Digital output : MCKRQ)
47 CONT O C Servo driver power supply control output
48 xrst O C CD LSI reset control output
49 VDCONT O C VD power supply control output
E
50 xsi I CD LSI serial data input
51 xso O C CD LSI serial data output
52 xck O C CD LSI serial clock output
53 xwait I C CD LSI wait control signal input
54 XASTB O C CD LSI address strobe output
55 AD0 O C Address/data Bus 0
56 INT Not used

DEH-30MP/XU/EW
5 6 7 8
61
 1 2 3 4

Pin No. Pin Name I/O Format Function and Operation

57 ROMDATA I/O E2PROM data input/output
58 ROMCK O E2PROM clock output
A
59 ROMCS O C E2PROM chip selection output
60,61 NC Not used
62 CLKOUT Not used
63 LOCK I Spindle lock input
64-68 NC Not used
69 BVSS B power supply GND
70 BVDD B power supply / Positive power supply
71-75 NC Not used
76 FLMD1 I/O /C Address/Data Bus 5
77-90 NC Not used
91-93 A/D Not used
B 94 csens Not used
95 TYPE_A/D Not used
96,97 NC Not used
98 TEMP Not used
99 VDSENS I VD power supply short sense input
100 DSCSNS Not used

* PE5505A
Format meaning
100

76

C C MOS
1 75

25 51
26

50

DEH-30MP/XU/EW
62
1 2 3 4
 5 6 7 8

- FM/AM Tuner Unit

7 6 13 5 10 9 8 11 14 18 19 20 21

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
NC
A

IC 3 EEPROM IC 5
←
5.0V 5V 3.3V

OSC LPF

AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER B
RF adj
ANT adj

T51 CF52

AUDIOGND

IC 4
OSCGND

VDD_3.3
←
RFGND

3.3V 3.3V 2.5V 2.5V

DGND

VCC
NC

2 12 15 22 16 4 17

No. Symbol I/O Explain

1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with C
an all antenna by way of 4.7µH. (LAU type inductor) A series circuit
including an inductor and a resistor is connected with RF ground for

2 RFGND RF ground
g Ground of antenna block
MANT I FM antenna input Input of FM antenna 75Ω Surge
g absorber is necessary.
4 VCC power supply ± 0.3V
5 SL O signal
g level Output of FM/AM signals
g level
6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active
7 NC non connection Not used
8 CE1 I chip enable-1 Chip enable for AF•RF ”High
g ” active
9 CK I clock Clock D
10 DI I data in
11 LDET O lock detector “ ” active
12 OSCGND osc ground
g Ground of oscillator block
13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.
14 DO O data out Data output
15 DGND digital
g g
ground Ground of digital
g block
16 NC non connection Not used
17 VDD_3.3 power supply The power supply for digital
g block. 3.3V ± 0.2V
18 RDS_CK O RDS clock Output of RDS clock(2.5V)
19 RDS_DATA DS data
20 RDS_LOCK O RDS lock Output unit “ ” E
“Low” active)
21 RDS_HSLK O RDS high speed Output unit “High
lock external transistor. “ ” active)
22 AUDIOGND audio ground
g Ground of audio block
23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output
24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output

DEH-30MP/XU/EW
5 6 7 8
63
 1 2 3 4
7.2.2 DISPLAY

DEH-30MP/XU/EW
64
1 2 3 4
 5 6 7 8

7.3 OPERATIONAL FLOW CHART

Power ON
A

VCC=5V
Pin 16, 62

bsens
Pin 19

B
bsens=L (B. UP ON)

asens
Pin 20

asens=L (ACC ON)

dsens
Pin 18

dsens=L (DETACH ON)

C
Starts
communication
with Grille
microcomputer. 300ms

SWVDD←H
Pin 7 300ms

In case of the above signal, the communication

with Grille microcomputer may fail.
Source keys
If the time interval is not 300msec, the oscillator
operative
may be defective. D

Source ON

SYSPW←H
Pin 48

E
Completes power-on operation.
(After that, proceed to each source operation)

DEH-30MP/XU/EW
5 6 7 8
65
 1 2 3 4

8. OPERATIONS

DEH-30MP/XU/EW
66
1 2 3 4
5 6 7 8

DEH-30MP/XU/EW
5 6 7 8
67
 1 2 3 4

About the fixing screws for the front panel

If you do not operate the Detaching and Replacing
the Front Panel Function, use the supplied fixing
A screws and fix the front panel to this unit.

Fixing screw
(CBA1994)

Fixing screw
(CBA1994)

DEH-30MP/XU/EW
68
1 2 3 4
5 6 7 8

DEH-30MP/XU/EW
5 6 7 8
69
 1 2 3 4

- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking
g the g
grating
g
L.P.F. Checking
g the g
grating
g ((Two pieces))

- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
B Grease GEM1045 CD Mechanism Module

Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
C
Portions to be cleaned Cleaning
g tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning
g paper
p p : GED-008

DEH-30MP/XU/EW
70
1 2 3 4