ORDER NO.

CRT4454
DEH-22UB/XSUC

CD RECEIVER

DEH-22UB /XSUC

This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks

CX-3269 CRT4488 S11iPod/USB CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2009
K-ZZZ. SEPT. 2009 Printed in Japan
 1 2 3 4

SAFETY INFORMATION

A
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
B

Where in a manufacturer’s service documentation, for example in circuit diagrams or lists

of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:

- Safety Precautions for those who Service this Unit.

When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
C
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION
CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
D

DEH-22UB/XSUC
2
1 2 3 4
 5 6 7 8

[Important Check Points for Good Servicing]

In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

3 Make sure the soldering of repaired locations is properly performed. B

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C

7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

a Safe environment should be secured during servicing. D

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts

Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws

To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-22UB/XSUC
5 6 7 8
3
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 6
2. SPECIFICATIONS ............................................................................................................................................ 7
2.1 SPECIFICATIONS...................................................................................................................................... 7
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 7
2.3 PANEL FACILITIES .................................................................................................................................... 8
2.4 CONNECTION DIAGRAM ....................................................................................................................... 10
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 11
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 11
3.2 PCB LOCATIONS .................................................................................................................................... 11
3.3 JIGS LIST ................................................................................................................................................ 12
3.4 CLEANING............................................................................................................................................... 12
B 4. BLOCK DIAGRAM.......................................................................................................................................... 14
5. DIAGNOSIS.................................................................................................................................................... 17
5.1 OPERATIONAL FLOWCHART ................................................................................................................ 17
5.2 ERROR CODE LIST ................................................................................................................................ 18
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 20
6. SERVICE MODE ............................................................................................................................................ 21
6.1 DISPLAY TEST MODE ............................................................................................................................ 21
6.2 CD TEST MODE ...................................................................................................................................... 22
7. DISASSEMBLY............................................................................................................................................... 23
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 29
8.1 CD ADJUSTMENT................................................................................................................................... 29
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 30
C
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 32
9.1 PACKING ................................................................................................................................................. 32
9.2 EXTERIOR(1) .......................................................................................................................................... 34
9.3 EXTERIOR(2) .......................................................................................................................................... 36
9.4 CD MECHANISM MODULE..................................................................................................................... 38
10. SCHEMATIC DIAGRAM ............................................................................................................................... 40
10.1 TUNER AMP UNIT(GUIDE PAGE) ........................................................................................................ 40
10.2 KEYBOARD UNIT.................................................................................................................................. 46
10.3 CD MECHANISM MODULE(GUIDE PAGE) .......................................................................................... 48
10.4 WAVEFORMS ........................................................................................................................................ 54
11. PCB CONNECTION DIAGRAM ................................................................................................................... 58
D 11.1 TUNER AMP UNIT................................................................................................................................. 58
11.2 KEYBOARD UNIT.................................................................................................................................. 62
11.3 CD CORE UNIT(S11USB) ..................................................................................................................... 64
12. ELECTRICAL PARTS LIST .......................................................................................................................... 66

DEH-22UB/XSUC
4
1 2 3 4
 5 6 7 8

1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A

1. You should conform to the regulations governing the product (safety, radio and noise, and other
regulations), and should keep the safety during servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside the unit.
3. To protect the pickup unit from electrostatic discharge during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the grating.
5. Be careful in handling ICs. Some ICs such as MOS type are so fragile that they can be damaged by
electrostatic induction. B
6. On CD Core Unit, actual cable colors and silk print are different.

C
Green Red
White Black

7. CD Mech. Assembly Wrong Installation Check

If iPod corresponding mech. assembly is installed at iPod non corresponding model, or if iPod non corresponding
mech. assembly is installed at iPod corresponding model by mistake, this becomes error indication with CDS,
USB sources as shown below;

Wrong Inst. Error of

C H K C D C O R E
CD Mech. Assembly

Judgment condition of wrong installation is as follows;

USB Corresponding Model

S11 USB/iPod Authentication IC: No OK
Mech. Assembly Authentication IC: Yes Wrong Installation Indication
S11 USB Mech. Authentication IC: No OK
Assembly Authentication IC: Yes Wrong Installation Indication
E

USB/iPod Corresponding Model

S11 USB/iPod Authentication IC: No Wrong Installation Indication
Mech. Assembly Authentication IC: Yes OK
S11 USB Mech. Authentication IC: No Wrong Installation Indication
Assembly Authentication IC: Yes OK

* The condition becomes as shown above since a microcomputer of corresponding USB mech. assembly and a
microcomputer of iPod corresponding mech. assembly are the same.

However, this is determined by the presence or absence of authentication IC since problem occurs depending on
F
different mech. assembly.

DEH-22UB/XSUC
5 6 7 8
5
 1 2 3 4

1.2 NOTES ON SOLDERING

A For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).

B The following lead-free solders are available as service parts:

Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

DEH-22UB/XSUC
6
1 2 3 4
 5 6 7 8

2. SPECIFICATIONS
2.1 SPECIFICATIONS
General CD player A
Power source .........................14.4 V DC (10.8 V to 15.1 V System ..................................... Compact disc audio system
allowable) Usable discs ..........................Compact disc
Grounding system................. Negative type Signal-to-noise ratio ............ 94 dB (1 kHz) (IHF-A net-
Maximum current consumption work)
...............................................10.0 A Number of channels ............ 2 (stereo)
WMA decoding format ........ Ver. 7,7.1, 8, 9, 10, 11 (2ch
Buck up current ......................2 mA or less
audio)
Dimensions (W × H × D): (Windows Media Player)
DIN MP3 decoding format ......... MPEG-1 & 2 Audio Layer 3
Chassis .................. 178 mm × 50 mm × 165 WAV signal format ................ Linear PCM & MS ADPCM
mm (Non-compressed)
(7 in. × 2 in. × 6-1/2 in.) B
Nose ....................... 188 mm × 58 mm × 24 mm USB
(7-3/8 in.× 2-1/4 in.× 1 in.) USB standard specification
D ............................................... USB 2.0 full speed
Chassis .................. 178 mm × 50 mm × 165 Maximum current supply .... 500 mA
mm Minimum memory capacity
(7 in.× 2 in.× 6-1/2 in.) ............................................... 256 MB
Nose ....................... 170 mm × 48 mm × 24 mm USB Class............................... MSC (Mass Storage Class)
(6-3/4 in.× 1-7/8 in.× 1 in.) File system.............................. FAT16, FAT32
Weight ..................................... 1.3 kg(2.9 lbs) WMA decoding format ........ Ver. 7,7.1, 8, 9, 10, 11 (2ch
audio)
Audio (Windows Media Player)
Maximum power output ....... 50 W × 4 MP3 decoding format ......... MPEG-1 & 2 Audio Layer 3 C
Continuous power output ... 22 W × 4 (50 Hz to 15 000 WAV signal format ................ Linear PCM & MS ADPCM
Hz, 5 % THD, 4 ohm load, (Non-compressed)
both channels driven)
Load impedance ................... 4 ohm FM tuner
(4 ohm to 8 ohm allowable) Frequency range .................. 87.9 MHz to 107.9 MHz
Preout maximum output level Usable sensitivity.................. 11 dBf (0.7 μV/75 ohm , mono,
.............................................. 2.0 V S/N: 30 dB)
Tone controls: Signal-to-noise ratio ............ 72 dB (IHF-A network)
Bass
Frequency ............ 100 Hz AM tuner
Gain ....................... ±12 dB Frequency range .................... 530 kHz to 1 710 kHz
D
Mid Usable sensitivity..................... 25 μV (S/N: 20 dB)
Frequency ............ 1 kHz Signal-to-noise ratio ............... 62 dB (IHF-A network)
Gain ....................... ±12 dB
Treble CEA2006 Specifications
Frequency ............ 10 kHz
Gain ....................... ±12 dB

Power output ............................. 14 W RMS × 4 Channels (4 ohm

and 1 % THD+N)
E
S/N ratio ....................................... 91 dBA (reference: 1 W into
4 ohm )

Note
Specifications and the design are subject to mod-
ifications without notice.

2.2 DISC/CONTENT FORMAT

DEH-22UB/XSUC
5 6 7 8
7
 1 2 3 4

2.3 PANEL FACILITIES

Head unit Part Operation

Press to increase or decrease vo-
VOLUME
lume.

Press to mute. Press again to un-

MUTE
mute.
B
AUDIO Press to select an audio function.

Press to select different displays.

DISP/ SCRL Press and hold to scroll through
the text information.

Press to pause or resume.

P art P art
Press to select functions.
AUX input jack (3.5 Press and hold to recall the initial
DISP/ / SCRL FUNCTION
mm stereo jack) setting menu when the sources
SRC / OFF USB port are off.

MULTI-CONTROL Press to display the disc title,

C (list) track title, folder, or file list de-
(M.C.) LIST /
pending on the source.
ENTER
Disc loading slot 1 to 6 While in the operating menu,
press to control functions.
(eject) / / /
CLOCK BAND / ESC
(detach)

Display indication
CAUTION
Use an optional Pioneer USB cable (CD-U50E) to
D connect the USB audio player/USB memory to
the USB port. Since the USB audio player/USB
memory is projected forward from the unit, it is
dangerous to connect directly.
Do not use the unauthorized product.

Indicator State
Remote control The disc (album) name is dis-
(disc)
played.

The disc (track) artist name is dis-

E (artist)
played.

Main dis- • Tuner: band and frequency

play sec- • Built-in CD player and USB:
tion elapsed playback time and
text information

The track (song) name is dis-

played.
(song)
A playable audio file has been se-
lected while operating the list.

DEH-22UB/XSUC
8
1 2 3 4
5 6 7 8

An upper tier of folder or menu

exists.

(folder) The list function is operated.

A lower tier of folder or menu ex-
ists.

LOC The local seek tuning is on.

B
LOUD
The loudness is on.
(loudness)

The selected frequency is being

(stereo)
broadcasted in stereo.
(repeat) Track or folder repeat is on.
(ran-
Random play is on.
dom)

The sound retriever function is

(sound re-
on.
triever)
C

DEH-22UB/XSUC
5 6 7 8
9
 1 2 3 4

2.4 CONNECTION DIAGRAM

Connection diagram

Power amp
This product (sold separately)

B Connect with RCA cables

(sold separately)
Antenna jack

Fuse (10 A) Rear output

Yellow System remote control

C
Connect to the constant 12 V
supply terminal. Blue/white
Connect to system control terminal of the
power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Red
Connect to terminal controlled
by ignition switch (12 V DC).

With a 2 speaker system, do not connect

Black (chassis ground) anything to the speaker leads that are not
D Connect to a clean, paint-free connected to speakers.
metal location.

White Gray
Front speaker Front speaker
White/black Gray/black
Left Right
Green Violet
Rear speaker Rear speaker
Green/black Violet/black
E

Rear speaker Rear speaker

Perform these connections when using

the optional amplifier.

DEH-22UB/XSUC
10
1 2 3 4
 5 6 7 8

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
A
To keep the product quality after servicing, please confirm following check points.

No. Procedures Item to be confirmed

1 Confirm whether the customer complain has The customer complain must not be
been solved. reappeared.
If the customer complain occurs with the Display, audio and operations must be
specific media, use it for the operation check. normal.
2 CD Play back a CD. No malfunction on display, audio and
(Track search) operation.
3 FM/AM tuner Check FM/AM tuner action. Display, audio and operations must be
(Seek, Preset) normal. B
Switch band to check both FM and AM.
4 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
5 Appearance check No scratches or dirt on its appearance after
receiving it for service.

See the table below for the items to be checked regarding audio:

Item to be checked regarding audio

Distortion
Noise
C
Volume too low
Volume too high
Volume fluctuating
Sound interrupted

3.2 PCB LOCATIONS

C CD Core Unit (S11USB)

E
A Tuner Amp Unit

B Keyboard Unit
Unit Number : YWM5449
Unit Name : Tuner Amp Unit
Unit Number :
Unit Name : Keyboard Unit F
Unit Number : CWX3776
Unit Name : CD Core Unit(S11USB)

DEH-22UB/XSUC
5 6 7 8
11
 1 2 3 4

3.3 JIGS LIST

A - Jigs List
Name Jig No. Remarks
Test Disc TCD-782 Checking the grating
L.P.F. Checking the grating (Two pieces)

- Grease List
B Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
Grease GEM1045 CD Mechanism Module

C
3.4 CLEANING

Before shipping out the product, be sure to clean the

following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
D

DEH-22UB/XSUC
12
1 2 3 4
5 6 7 8

DEH-22UB/XSUC
5 6 7 8
13
 1 2 3 4

4. BLOCK DIAGRAM

A
A TUNER AMP UNIT
SYS+B SWVDD3V
ANTENNA ANT401

REFA

CE1
LDET
IFB

REFB
1

IFA

CE2
DO
CK

SLOUT
DI
SL-IN
2

1 ANT 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

IFOUTA

VDD

CE1
RFGND1

RFGND2

RFGND3

RFGND4

DO

SLOUT
LDET

CE2
REFINA

REFINB
IFOUTB

DI
DGND

CK
VCC
ANT

SLIN
IC2
EEPROM SL-IN
IFA
IFB
REFA
REFB
LDET
B DI
CK
CE1
DO
VCO LFP CE2
SLOUT

ATT
ATT TANK

IC1
MIX / IF / PLL

ATT RF LFP

ELECTRON
CF SOURCE

C
FM/AM TUNER UNIT
TUNL
2
IN2_L

IC
CD-Lch
PML
1
IN1_L

VCK, VDT, VST

REGULATOR IC
IC911
BA49181-V12 SYSTEM
1 47 COMP
VDDCONT PWROFF
5 2 36 IC60
SW5V SW5V BESNS BSENS
3 PN5
D SWVDD3V
6
SWVDD SYSPW 15
SYSPW
7 4 1
SYS+B SYS+B SW5VCONT SWVDD
8
VDD3V VDD +B 10 B.UP

C CD CORE UNIT(S11USB) +B.UP

9

SWVDD3V
PICKUP UNIT RF AMP, CD DECODER, MP3&WMA DECODER
(P10.5)(SERVICE) DIGITAL SERVO/DATA•PROCESSOR Q601
85
DREG
CPU, USB HOST CONTROLLER
VDD
CN101
LD 9
LD- 141 M-REGC
15 15 Q101 LD 1
USBXTAL 55
PLL_VDD
MD 142 X205
5 5 PD 57
REFO 48MHz DVDD3
VREF 8 133 2 94
8 REFOUT /USBXTAL DVDD2
AC,BD,E,F 121
HOLOGRAM 50 DVDD4
UNIT XTAL
FOM FOM X201 IC501
3 3 ACTUATOR/ 52 16.93MHz USB5V BD9007F
FOP FOP /XTAL
MD
FOCUS ACT. 2 2 MOTOR DRIVER B.UP
1
TRACKING ACT. TOP 1 1 TOP Q102
PVin
TOM IC301 8 5 25
4 4 TOM VCC VDD Vin EN SYNC
LD+
14 14
BA5839FP TD,FD 1 2
E 12 FOM 39 CN701 CN651 IC712 VIN SW
11 FOP SD,MD /PUEN BD6538G 3 28
14 55 LOUT LOUT EN USBCTL
TOP LOUT 13 7 4 27
13 5 FLG FLG
TOM IC201 USB5V VOUT
SPINDLE
MOTOR M PE5715A VDD
VDD
9 11
VDD
VDD3V
16 Q751
SOP LOEJ 22 28
LOEJ VD VD CD VD
15 VD 2 18 B.UP
SOM 21 20
18
LOADING/CARRIAGE LCOP CLCONT CLCONT
1 19 Q752
MOTOR M 17
LCOM CONT
9 41
CONT
5

126
VDCONT

7
8EJ 16
10 /RESET RESET 16
DSCSNS /RESET 8 12 CDRESET
9
HOME
BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK
S905 S903 S901
8EJ DSCSNS HOME BDATA,BSCK

5 DP USDP
DP 16 4
4 DM USDM
DM 17 3
F VD

11
VDSENS

DEH-22UB/XSUC
14
1 2 3 4
 5 6 7 8

SYSTEM MICRO
COMPUTER
IC601(1/2)
PN5034A

SL-IN 62 SL
IFA 77 IF_INA
CN251
IFB 78 IF_INB RL 2 RCA OUT
REFA 96 FREFA
REFB 97 FREFB Q251
LDET 99
LOCK
DI 100 TUNDO B
CK 101 TUNCK
CE1 102
CE
DO 103
TUNDI
CE2 109
CE2
SLOUT 136
SL JA901
ASENSE B.UP
B.UP
18
Q921
59 35 ASENS ACC
L_OUT ASENS 13

GND
16

ELECTRONIC VOLUME/
SOURCE SELECTOR POWER
CONNECTOR
9 FL+ 1
FL+
TUNL Rear_L
7 12
RLIn FL- 7 FL- C
2 3
IN2_L 5 RL+
6 11 AMP RL+
3
5
FLIn RL-
IC201 Front_L IC301 RL- 7
PML014B PAL007E
CD-Lch 1 AUX-L 22 25 BREM
IN1_L IN4+_L 4 MUTE B.REM 14
5 AUX-G 6
IN4-_L VCC B.UP
4
STBY VCC 20
VCK, VDT, VST

MUTE
Q351(2/2)

SYSTEM MICRO
47 COMPUTER MUTE
PWROFF
36 IC601(2/2) Q351(1/2)
BSENS PN5034A 44
15
SYSPW MUTE D
1
SWVDD
B.UP

VDD3V
82
85 XOUT
DREG X601

9
M-REGC
XIN
81 74.1MHz
B KEYBOARD UNIT
55
PLL_VDD CN832 CN1821 CN1901
AUX R 3
57 52
DVDD3 BU_X1 AUX-L AUX L AUX L 2 FRONT
94 7 7
DVDD2 X681 AUX-G AUX G AUX G 1 AUX
4.7186MHz 5 5
121 51 KEY MATRIX
DVDD4 BU_X2
S1823 S1825 S1827 S1829
SW5V S1824 S1826 S1828 S1830
F 3 3 SW5V
S1845 LEFT UP RIGHT DOWN

111 ROT1 ROT1 1 4 KST1 S1821 S1831 S1833

5 25 ROT1 6 S1822 S1832 S1834
SYNC 6
110 ROT0 ROT0 2 5 KDT2 SRC LIST BAND/ESC
ROT0 4 4
S1835 S1836 S1837
E
28 3
USBCTL ILLUMI 6 5 4
27 D1852-D1857
FLG ILMPW D1861-D1870 AUXV/SOURCE S1838 S1839 S1840
Q801 1 2 3
ILM+B ILM+B
B.UP 12 12 S1843
S1841 S1842 S1844
B.UP CD EJECT REGION DISP/BACK
LCDBK
2 D1851
ILMPW Q802
REMOTE CONTROL
KDT0-3

KST0-4

SENSOR
126 3 IC1802 1
VDCONT SW5V
VCC GP1UXC14RK REM

33 17
16 SOURCE SOURCE
CDRESET SRC 11 11 REM KEY DATA 23
X1
24 X1801
KYDT KYDT 20 5.00MHz
KYDT 19 19 KYDT 22
LCD DRIVER/ X0

DPDT
23 DPDT
17 17
DPDT 18
DPDT KEY CONTROLLER
10 IC1801
VLCD LCD1801
56
VDD
PD6340A
34 DSENS DSENS
DSENS 20 20 F
CN1911
USB5V USB5V USB5V USB5V
18 18 1
USDP DP DP DP
14 14 3 USB
USDM DM DM DM
16 16 2

DEH-22UB/XSUC
5 6 7 8
15
 1 2 3 4

LCD (CAW1970)
A

E
SEGMENT

COMMON

DEH-22UB/XSUC
16
1 2 3 4
 5 6 7 8

5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON

VDD = 3.3 V
Pin 8

BSENS
Pin 36
BSENS = L B

ASENS
Pin 35

ASENS = L

Starts
communication
with Grille
microcomputer.

C
300 ms
SWVDD <- H
Pin 1
300 ms
In case of the above signal, the communication
Source keys
with Grille microcomputer may fail.
operative
If the time interval is not 300 msec, the oscillator
may be defective.

Source ON

SYSPW <- H
Pin 15

Completes power-on operation.

(After that, proceed to each source operation)

DEH-22UB/XSUC
5 6 7 8
17
 1 2 3 4

5.2 ERROR CODE LIST

ERROR CODES
If a CD or USB memory device is inoperable, or operation of such media is stopped by an error, the error mode is established
A
and a cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from
customers and facilitate failure analysis and repair work in servicing.

(1) DISPLAY METHOD

If “0xFD” error mode is displayed in CD MODE (CD MODE area for display) or USB MODE (USB MODE area), an error code
will be displayed in the DMIN (minute display) and DSEC (second display) areas.

The same code is displayed in the DMIN and DSEC areas.

The DTNO area is blank (#0FFH), as it conventionally was.
• The error mode for a VD error is 0xFB. (This is because the system microcomputer recognizes a VD error even in the No
Display format.)
B • Display example of the head unit
Depending on the display capability of LCDs, the display format varies, as shown below. XX denotes an error number.
Note: In a case of an OEM product, the error display format is subject to the specifications used by the equipment
manufacturer.
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx

(2) LIST OF CD ERROR CODES (Error Mode: 0xFD)

Code Classification Error code to be displayed Details and possible causes
C 10 Electricity Carriage Home NG The CRG cannot move toward the inner track.
Failure in communica- The CRG cannot move from the inner track.
tion with the Servo LSI --> Defective HOME SW; Failure in CRG movement; Failure in communication between
the microcomputer and the Servo LSI.
11 Electricity Focus Search NG Focusing not available
--> Disc placed upside-down; CD-RW disc used; Stains on the disc; excessive vibration.
12 Electricity Spindle Lock NG Spindle not locked. Subcode not readable.
Subcode NG Proper RF AMP gain not obtained.
RF-amp NG --> Defective spindle; Scratches or stains on the disc; excessive vibration.
--> A CD-R disc that does not contain data loaded, or in a rare case, disc placed upside-down.
--> CD signal error.
15 Electricity Failure in RF data RF not read
--> A CD-R disc that does not contain data loaded
--> A CD-RW disc that does not contain data loaded
D
17 Electricity Setup NG AGC protection does not work. Focus can be easily lost.
--> Scratches or stains on the disc; excessive vibration; CD-RW disc used.
22 Disc No playback Playable MP3 or WMA file not found
--> No MP3 or WMA file exists on the loaded CD-ROM disc.
23 Disc File Format NG Data are written in a file format not supported.
--> A CD-ROM disc on which data are written in a file format other than ISO 9660,
Level-1 or -2 (for example, in UDF) is loaded.
24 Disc All DRM All the playable files on the disc are DRM-protected.
--> This error code will not be displayed when even one file not protected by DRM is
contained on the disc.
30 Electricity Search Time Out Failed to reach a target address
E --> CRG tracking error or scratches on the disc
50 Mechanism Failure in ejection Disc ejection not completed
--> A foreign object inserted in the mechanism; Disc jammed.
51 Mechanism Failure in retried Disc could not be ejected even after disc turning had been retried.
turning for ejection --> A foreign object inserted in the mechanism; Disc jammed.
52 Mechanism Failure in disc loading Disc loading not completed
--> A foreign object inserted in the mechanism; Disc jammed.

NOTES
• Indications of error codes are available only during disc operations, because CD operations are
unavailable if a mechanical error is generated.
• If the TOC cannot be read, this is not processed as an error, and operation continues accordingly.
F
• If you design a new head unit, be sure to use one of the display formats indicated in “Display example of
the head unit.”

DEH-22UB/XSUC
18
1 2 3 4
 5 6 7 8

• The 2 high-order digits of an error code denote the main • How to restore from each error is shown below.
classification, shown below. 1x, 2x, 3x, and 4x: ACC-OFF then ON, CD-OFF then ON,
1x: Setup-related errors Disc ejection, DKSTOP then DKPLAY
2x: Errors related to TOC reading 5X: ACC-OFF then ON, Disc ejection, Disc reloading, A
3x: Search-related errors Disc removal
4x: Playback-related errors Ax: ACC-OFF then ON
5x: Loading-ejection-related errors
Ax: Other type of errors

(3) USB-RELATED ERROR CODES

Code Classification Error code to be displayed Details and possible causes
16 Device iPod authentication error Authentication of iPod failed
(*1) --> After a reattempt of iPod authentication, an error was returned from the iPod machine
and authentication IC.
18 Device Unsupported device Connection of a device not supported was detected. B
--> A device other than a mass-storage device and iPod is connected.
--> An iPod of a generation earlier than 5G/nano is connected. Or, an iPod (even one of a
generation after 5G/nano) with the firmware that does not support digital streaming is
connected.
19 Device Communication error Communication with a device failed.
--> Communication failed because of a defective device, etc.
22 Device Playback unavailable Playable file (MP3/WMA/AAC/WAV) not found
--> No playable file (MP3/WMA/AAC/WAV) exists in the device set.
23 Device File Format NG Data are written in file format not supported.
--> A format other than FAT is used.
24 Device All DRM All the playable files on the disc are DRM-protected.
--> This error code will not be displayed when even one file not protected by DRM is C
contained on the disc.
*Error code only for models that support iPod.

NOTES • How to restore from each error is shown below.

• The 2 high-order digits of an error code denote the main 1x: ACC-OFF then ON, USB-OFF then ON, Device removal,
classification, shown below. DKSTOP then DKPLAY
1x: Setup-related errors 2X: ACC-OFF then ON, USB-OFF then ON, Device removal,
2x: Errors related to file-system reading DKSTOP then DKPLAY
Ax: Other type of errors Ax: ACC-OFF then ON

(4) LIST OF ERROR CODES (Error Mode: 0xFA) Only for USB
D
Code Classification Error code to be displayed Details and possible causes
A1 System Failure in power supply Excess current detected in the USB bus.
--> Electric current exceeding the specified 500 mA flowed in the USB bus.
The bus power is shut off and the unit is stopped in response to an error.
For restoration, turn the unit OFF then back ON again
Note: Whether power supply failed or not can be judged from just the error mode (0xFA). (Referring to the error code [0xA1] is not necessary.)

(5) LIST OF ERROR CODES (Error Mode: 0xFB) Only for CD

Code Classification Error code to be displayed Details and possible causes
A0 System Failure in power supply A voltage or ground short was generated in the VD power.
--> Defective SW transistor; Failure in the power supply unit (defective connector); E
Ejection is not possible; Restoration is only possible by turning the unit OFF then
back ON again.
Note: Whether power supply failed or not can be judged from just the error mode (0xFB). (Referring to the error code [0xA0] is not necessary.)

(6) ACTIONS OF CD/USB DURING ERROR

Mode Error code CD action USB action Mode Error code CD action USB action
1x Stopped for an error Operable 4x Stopped for an error Operable
FD
2x (CD) Stopped for an error Operable 5x Stopped for an error Operable
FD
2x (USB) Operable Stopped for an error FB A0 Stopped for an error Operable
3x Stopped for an error Operable FA A1 Operable Stopped for an error F

DEH-22UB/XSUC
5 6 7 8
19
 1 2 3 4

5.3 CONNECTOR FUNCTION DESCRIPTION

A REAR
OUTPUT

ANTENNA

15 13 11 9 7 5 3 1
16 14 12 10 8 6 4 2

C 1 FL+ 9 TEL
2 FR+ 10 NC
3 FL- 11 NC
4 FR- 12 NC
5 RL+ 13 ACC
6 RR+ 14 B.REM
7 RL- 15 B.UP
8 RR- 16 GND

DEH-22UB/XSUC
20
1 2 3 4
 5 6 7 8

6. SERVICE MODE
6.1 DISPLAY TEST MODE
A

1. To enter the test mode (1)

Turn on ACC and Backup while pressing the RIGHT and the DOWN buttons together.

2. Operation method

Key Contents
LIST All lighting of display
1 All lights out of display
4 LCD check mode A

5 LCD check mode B

6 LCD check mode C

DISP System version display

V E R # #.# #
C
ex.) Ver.7.01 -> “VER 7.01”

3. To enter the test mode (2)

Turn on ACC and Backup while pressing the 1 and the 3 buttons together.

4. Operation method

Change display as follows by pressing the 1 and the 3 buttons together.

D
[Test Overview]
Start to test mode

ROM Correction version display

ROM Correction is not connected

N O E E P R OM
ROM Correction check sum error
S U M E R R O R
Normal movement
E
S1 S2 S3 S4 C1 C2 C3 C4
Sn ROM Correction number
Cn CH use information (1:Use / 0:Not use Corresponds from the left to CH1, CH2, CH3, CH4)

Normal display

The display mode to the display usually.

Display stop

To the static display of the display mode.

DEH-22UB/XSUC
5 6 7 8
21
 1 2 3 4

6.2 CD TEST MODE

- Flow Chart
[4] + [6] + Reset [CD] or [SOURCE] [Key]
Test Mode IN Source ON
A Contents
TRK MIN
Display

[BAND] [3] [2] [4]

Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

[BAND] [3] [6] [1] [<] [>] [2]

[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
Gop Mode *10
S curve check *2 Close *8 *8 switching *3
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL
B

[BAND] [1] [6] [3] [<] [>] [2]

Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] [<] [>] [2]

Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching *5 *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

*6

[BAND] [2]
C
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X

or 9X 9X 9X

Operation
*1) TYP t + 6 dB t + 12 dB [Key] Test Mode
TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [BAND] Power On/Off
[<] CRG + / TR Jump +
(Direction of the external surface)
*2) Focus Close t S. Curve t F EQ measurement setting [>] CRG - / TR Jump -
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 (Direction of the internal surface)
(TRK99MIN99SEC99) [1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
D
[2] RF Gain switching / Offset adjustment display /
*3) F.Offset Display t T.Offset Display t Switch to the T.Balance adjustment / T. Open
order of the original display
[3] F. Close,S. Curve / Rough Servo and RF AGC /
F,T,RF AGC
[4] SPDL 1X/2X switching
*4) 1TR/4TR/10TR/32TR/100TR
As for the double speed(2x), audio output cannot be
*5) Singlet 4TR t10TR t 32TR t 100TR tCRG Move
supported.
9x(8x):91(81) 92(82) 93(84) 94(84) 95(85) 96(86)
[5] Gop Mode switching
*6) Only at the time of CRG move, 100TR jump [6] F. Mode switching / Tracking Close / CRG TR
Jump Switching
*7) TRK/MIN/SEC t F.AGC t T.AGC Gain t F.Bias t RF AGC

*8) CRG motor voltage = 2 [V]

*9) TYP (1X) t 2X t 1X *10) OFF(TYP) t FORCUS t TRACKING

TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

As for the double speed (2x), audio output cannot be supported

*) After the [EJECT] key is pressed keys other than the [EJECT] key should not be pressed, until disc ejection is complete.
When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
F the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
Do not do Tracking Servo Close before doing Focus Servo Close. (Because the overcurrent flows)

DEH-22UB/XSUC
22
1 2 3 4
 5 6 7 8

7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
A

- Removing the Case and Panel Assy (Fig.1)

Case

Remove the Case.

Remove the two hooks

1
and then remove the Panel Assy. B
1 1
Fig.1
Panel Assy

- Removing the CD Mechanism Module (Fig.2) CD Mechanism Module

1
C
1 Remove the four screws.
1

Disconnect the FFC

2
and then remove the CD Mechanism Module.

2
1 1

Fig.2 D

- Removing the Tuner Amp Unit (Fig.2, 3)

1
Remove the two screws.(Fig.3) 1
1

Fig.3
E
2 Remove the two screws.(Fig.4)
4
3
4

Straighten the tabs

3
at two locations indicated.(Fig.4)

2
Remove the two screws 3 2
4
and then remove the Tuner Amp Unit.(Fig.4)
F
Fig.4
Tuner Amp Unit

DEH-22UB/XSUC
5 6 7 8
23
 1 2 3 4

How to Hold the Mechanism Unit

1. Hold the Upper and Lower Frames at the specified parts (circled with broken blue lines in the photo below).
2. You can hold the tabs of the Lower Frame (circled with broken green lines in the photo below) if you do so only while lifting
A the Mechanism Unit from the table. Keeping the Mechanism Unit lifted by holding these tabs with your fingers may result in
deformation.
3. Be careful NOT to hold the front part of the Upper Frame or the CRG Mechanism and NOT to insert foreign objects into
these mechanisms. Doing so may result in deformation.
Proper handling

Improper handling
C

DEH-22UB/XSUC
24
1 2 3 4
 5 6 7 8

Mechanism Module: How to Set to the Quasi-Clamp State (Driven by the Motor)
1. Remove the solder from the CRG-motor lead wire (Fig. 1).
2. Push in the Disc Detection Arm while applying 4-V power to the CRG Motor (Fig. 2). (Apply 4-V power to the green lead
A
wire. The white lead wire is for grounding.)
The Mechanism Module is set to the clamped state, and the PU will move toward the outer track.
Note: NEVER apply power to the CRG-motor lead wire without removing the solder from the wire. Doing so may result in
damage to the ICs and the PU.
3. Stop the motor when the PU reaches around the middle track.
Note: Jumpiness will occur when the PU reaches the outermost track. Although jumpiness does not constitute a problem,
it is recommended that it occur as least frequently as possible.

Note: Be aware that the colors of the lead wires do not match the
Fig. 1 indications on the Core Board Pattern (green wire to O and
white wire to P).

Disc Detection Arm

D

Fig. 2
F

DEH-22UB/XSUC
5 6 7 8
25
 1 2 3 4

How to Remove the PU Unit

1. Set the unit to the quasi-clamp state, following the procedures described in “Mechanism Module: How to Set to the Quasi-
Clamp State (Driven by the Motor).”
A 2. Temporarily change the engagement position of the bias spring of the feed screw (Fig. 2b).
Be careful not to cut yourself on the tip of the spring.
3. Hold the PU unit by parts A in Fig. 1 then slide it toward the inner track.
4. Remove the backend of the feed screw from the outer holder, by first sliding it, as shown in Fig. 3, then lifting it.
5. Remove the PU unit, by lifting it. Lifting the PU unit will disengage the PU unit from the part B of the chassis.
Note: When reassembling the PU unit, be sure to securely engage the PU unit with the part B of the chassis, as shown in
Fig. 4. Also, be sure to change the engagement position of the bias spring of the feed screw to its original position
(Fig. 2a). After reassembling, perform the PU adjustment, following the description in the service manual.

Slide toward the inner track.

One end of the spring is engaged

Backend of Outer holder beneath the resin flange and
the feed screw plate bend.
C
Fig. 2a
Fig. 3 Original engagement
position

Fig. 1

Fig. 2b
Temporary engagement
position

[Improper assembly]
Properly assembled state The chassis is not properly pinched by
Fig. 4
the PU case and PU rack.

How to Move the PU toward the Outer Track

1. Set the unit to the quasi-clamp state, following the procedures described in “Mechanism Module: How to Set to the Quasi-
Clamp State (Driven by the Motor).”
2. Move the PU unit toward the outer track, by applying 1.5-V power to the CRG motor.
Note: After moving the PU toward the outer track and taking the necessary measures, be sure to solder the lead wires.
F

DEH-22UB/XSUC
26
1 2 3 4
 5 6 7 8

How to Remove the PU Rack

1. Remove the PU Unit, following the procedures described in “How to Remove the PU Unit.”
2. Remove the PU Rack fixing screw (Fig. 1). A
3. Remove the PU Rack, by applying force in the direction of the arrow in Fig. 2.
Notes:
While handling the PU Unit, be careful NOT to touch the actuator block shown in Fig. 6 or bang the actuator block against
your workbench.
Handle the PU and PU Unit with care, according to the description in “How to Hold the PU.”
When reattaching the PU Rack to the PU, first reassemble parts a and b shown in Fig. 3 into the PU case then attach the
boss shown in Fig. 4 to the PU case.
After reassembling the PU Rack, insert the feed screw from side c in Fig. 5 (insertion depth: Approx. 18 mm for the part
indicated in the photo).

PU Rack
B

PU Rack
fixing screw

Fig. 4 C

Fig. 1

18 mm

c D

Fig. 5

Fig. 2
Actuator block

a
Fig. 3 b
Fig. 6
F

DEH-22UB/XSUC
5 6 7 8
27
 1 2 3 4

How to Hold the PU

1. Be sure to hold the PU at the positions shown in “Proper handling.” NEVER hold it as shown in “Improper handling.”
A
Proper handling Improper handling

Do not touch the object lens

and ACT.

Do not touch the VR.

Do not touch the Hologram.

E Do not pull the FPC.

DEH-22UB/XSUC
28
1 2 3 4
 5 6 7 8

8. EACH SETTING AND ADJUSTMENT

8.1 CD ADJUSTMENT
A

1) Cautions on adjustments 2) Test mode

In this product the single voltage (3.3 V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65 V) To enter the test mode.
instead of the GND. [1]+[6]+[DISC](three times) press
If you should mistakenly short the REFO1 with the GND u
during adjustment, accurate voltage will not be obtained, Diagnosis IN
and the servo’s misoperation will apply excessive shock u
to the pickup. To avoid such problems: [DISC]+[RIGHT] press
a. Do not mix up the REFO1 with the GND when u
connecting the (-) probe of measuring instruments. Display : PBUS TEST
Especially on an oscilloscope, avoid connecting the (-) u B
probe for CH1 to the GND. [DISC] pressed for 1.7 seconds or more
b. In many cases, measuring instruments have the same u
potential as that for the (-) probe. Be sure to set the Diagnosis OUT
measuring instruments to the floating state. u
c. If you have mistakenly connected the REFO1 to the GND, [DISC] press
turn off the regulator or the power immediately.
To exit from the test mode.
Before mounting and removing filters or leads for Turn off the ACC and back up.
adjustment, be sure to turn off the regulator.
Notes:
For stable circuit operation, keep the mechanism a. During ejection, do not press any other keys than the
operating for about one minute or more after the EJECT key until the loaded disc is ejected. C
regulator is turned on. b. If you have pressed the ( ) key or ( ) key during focus
search, turn off the power immediately to protect the
In the test mode, any software protections will not actuator from damage caused by the lens stuck.
work. Avoid applying any mechanical or electrical c. For the TR jump modes except 100TR, the track jump
shock to the mechanism during adjustment. operation will continue even if the key is released.
d. For the CRG move and 100TR jump modes, the tracking
The RFAGC and RFO signals with a wide frequency range loop will be closed at the same time when the key is
are easy to oscillate. When observing the signals, released.
insert a resistor of 1k ohms in series. e. When the power is turned off and on, the jump mode
is reset to the single TR (91), the RF amp gain is set to 0 dB,
The load and eject operation is not guarantied with the and the auto-adjustment values are reset to the default
mechanism upside down. If the mechanism is blocked settings. D
due to mistaken eject operation, reset the product or
turn off and on the ACC to restore it.

DEH-22UB/XSUC
5 6 7 8
29
 1 2 3 4

8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

B Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE

CD CORE UNIT

C REFO1
E F

L.P.F.

Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF

F 100 kohm

VREF 390 pF

D L.P.F.

Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the right and left buttons, move the PU unit to the innermost track.
3. Press key CH4 to close focus, the display should read "91". Press key CH3 to implement the tracking
balance adjustment the display should now read "81". Press key CH4. The display will change,
returning to "81" on the fourth press.
E 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
difference is within 75 . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-22UB/XSUC
30
1 2 3 4
 5 6 7 8

Grating waveform Ech -> Xch 20 mV/div, AC

Fch -> Ych 20 mV/div, AC
A

0 degrees 30 degrees

45 degrees 60 degrees

75 degrees 90 degrees

DEH-22UB/XSUC
5 6 7 8
31
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
"
Screw adjacent to mark on the product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
9.1 PACKING

DEH-22UB/XSUC
32
1 2 3 4
 5 6 7 8

PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Polyethylene Bag CEG1173 10 Screw TRZ50P080FTC

2 Remote Control Unit CXE2758 A
3 Cord Assy YDP5039 11 Unit Box YHG5557
4 Screw BPZ20P060FTC 12 Contain Box YHL5557
5 Polyethylene Bag CEG1160 13 Protector YHP5071
14 Protector YHP5072
6 Handle CND3707 * 15-1 Warranty Card CRY1276
7 Screw Assy YEA5072
* 8 Polyethylene Bag CEG-127 15-2 Owner's Manual YRD5305
9 Screw CRZ50P090FTC

Owner's Manual
B
Part No. Language

YRD5305 English, French, Spanish(Espanol)

DEH-22UB/XSUC
5 6 7 8
33
 1 2 3 4

9.2 EXTERIOR(1)

DEH-22UB/XSUC
34
1 2 3 4
 5 6 7 8

EXTERIOR(1) SECTION PARTS LIST

Mark No. Description Part No.
1 Holder CND3598
2 Remote Control Unit CXE2758 A
3 Cover CNS7068
4 Cord Assy YDP5039
5 Case YNB5063

6 Panel YNS5537
7 Detachable Assy YXA5680
8 Screw BPZ20P100FTC
9 Spring CBH2210
10 Button(DISP, SRC, UP) YAC5384

11 Button(ESC, DOWN, LEFT) YAC5385 B

12 Button(1, RIGHT, 4, 5) YAC5386
13 Button(2, 3, 6, LIST) YAC5387
14 Button(EJECT, CLOCK) YAC5388
15 Button(DETACH) YAC5389

16 Cover YNS5536
17 Grip(USB) YNV5194
18 LCD(LCD1801) CAW1970
19 Spacer CNN2527
20 Holder YNC5083
C

21 Rubber YNV5191
22 Connector YNV5192
23 Lighting Conductor YNV5193
24 Grille Unit YXA5688
25 Knob Unit YXC5124

26 Spring YBL5010

DEH-22UB/XSUC
5 6 7 8
35
 1 2 3 4

9.3 EXTERIOR(2)

A
B

DEH-22UB/XSUC
36
1 2 3 4
 5 6 7 8

EXTERIOR(2) SECTION PARTS LIST

Mark No. Description Part No.
1 Screw ASZ26P050FTC
2 Screw ASZ26P080FTC A
3 •••••
4 Screw BSZ26P060FTC
5 Screw BSZ26P100FTC

6 •••••
7 CD Mechanism Module(S11) CXK5870
8 Cable YDE5059
9 Holder YND5048
10 Tuner Amp Unit YWM5449

11 Screw BPZ26P080FTC B
12 Screw BSZ26P060FTC
13 Screw BSZ26P160FTC
14 FM/AM Tuner Unit CWE2025
15 Holder CND3466

> 16 Fuse(10 A) YEK5001

17 Holder YND5045
18 Heat Sink YNR5139
19 Chassis Unit YXA5652
20 Spring CBH2961
C

21 Spring CBH2962
22 Arm CNV9312
23 Arm CNW1439
24 Panel Unit YXA5650
25 Button CAC4836

26 Spring YBH5012

DEH-22UB/XSUC
5 6 7 8
37
 1 2 3 4

9.4 CD MECHANISM MODULE

A
(C)
(C)

B
B

(A)

(C)

(A)

D B C (A)
C
(D) (A)
D
C
(D)

(C)

(B)

(D)
(A)

(C) (A) (A)

D

(A) (A)

(C)

A C
(C)

(C) (A) : GEM1045

(B) : GEM1038

F (C) : GEM1024

(D) : GEM1043

DEH-22UB/XSUC
38
1 2 3 4
 5 6 7 8

CD MECHANISM MODULE SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 Screw BMZ20P020FTC 50 Damper CNW1198

2 Screw BSZ20P040FTC A
3 Screw(M2 x 4) CBA1835 51 Arm CNW1726
4 Washer CBF1038 52 Motor Unit CXC4026
5 Spring CBH3010 53 Screw Unit CXC8894
54 Arm Assy CXC8896
6 Spring CBH2855 55 Washer CBF1037
7 Spring CBH2856
8 Spring CBH2860 56 Washer CBF1038
9 Spring CBH2609 57 Arm CND4554
10 Spring CBH3011 58 Collar CNV6906
59 Roller CNW1196
11 Spring CBH3012 60 Gear Unit CXC8893 B
12 Spring CBH3014
13 Spring CBH3015 61 Washer YE15FTC
14 Spring CBH3016 62 Chassis Unit CXE1946
15 Spring CBH3017 63 Motor Unit CXE2273
64 Screw JFZ20P025FTC
16 Spring CBH3018 65 Screw JGZ17P022FTC
17 Spring CBH3019
18 Spring CBH3020 66 Screw IMS20P030FTC
19 Spring CBL1797 67 CD Core Unit (S11USB) CWX3776
20 Pickup Unit(S10.5)(Service) CXX1942
C

21 Bracket CND4553
22 Arm CND4555
23 Frame CND4557
24 Frame CND5217
25 Lever CND5398

26 Sheet CNN2280
27 Rack CNV8342
28 Guide CNW1171
29 Roller CNW1172 D
30 Arm CNW1173

31 Arm CNW1174
32 Roller CNW1175
33 Lever CNW1176
34 Arm CNW1177
35 Arm CNW1178

36 Gear CNW1180
37 Gear CNW1181
38 Gear CNW1182 E
39 Gear CNW1183
40 Rack CNW1184

41 Gear CNW1185
42 Gear CNW1186
43 Gear CNW1187
44 Gear CNW1188
45 Clamper CNW1190

46 Arm CNW1192
F
47 Holder CNW1193
48 Holder CNW1194
49 Damper CNW1197

DEH-22UB/XSUC
5 6 7 8
39
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 TUNER AMP UNIT(GUIDE PAGE)
A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
Large size
SCH diagram
A-a CD/USB/SD(-20 dB): -19.4 dBs
A-a A-b
C CN701

NOTE :
Symbol indicates a resistor.
A-a A-b Guide page No differentiation is made between chip resistors and
discrete resistors.
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
A-a A-b Detailed page discrete capacitors.

NM : No Mount
B
The > mark found on some component parts indicates
the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of
identical designation.

FM(10%):-33.5 dBs
AM(15%):-30.0 dBs

C
FM/AM TUNER UNIT

PN5035B

F AUX1(-20 dB):-17.8 dBs

A B CN1821

DEH-22UB/XSUC
40
1 2 3 4
 5 6 7 8

SB/SD(-20 dB): -19.4 dBs A-b

C CN701
A TUNER AMP UNIT

FM:-37.1 dBs
AM:-33.6 dBs
CD/USB/SD:-22.4 dBs
AUX1:-20.8 dBs

FM:-16.0 dBs
AM:-11.5 dBs
CD/USB/SD: -9.3 dBs
AUX1: -9.7 dBs

>

3A

N5035B

600uH

FM: +9.98 dBs

AM:+14.48 dBs
CD/USB/SD: +16.7 dBs
AUX1: +16.3 dBs

E
NM

NM

NM

A
DEH-22UB/XSUC
5 6 7 8
41
 F
E
B
A

D
C

42
A-a A-b
A-b
A TUNER AMP UNIT

1
1

FM:-37.1 dBs
AM:-33.6 dBs
CD/USB/SD:-22.4 dBs
AUX1:-20.8 dBs

FM:-16.0 dBs
AM:-11.5 dBs
CD/USB/SD: -9.3 dBs
AUX1: -9.7 dBs

2
2

>

3A

DEH-22UB/XSUC
3
3

4
4
 5

5
600uH

6
6

FM: +9.98 dBs

AM:+14.48 dBs
CD/USB/SD: +16.7 dBs
AUX1: +16.3 dBs

NM

DEH-22UB/XSUC
7
7

NM

NM
8

8
A-a A-b
A-b

43
E
A

D
C

F
B
 F
E
B
A

D
C

44
A-a A-b
CD/USB/SD(-20 dB): -19.4 dBs A-b

A-a
C CN701

1
1

NOTE :
Symbol indicates a resistor. FM:
AM:
No differentiation is made between chip resistors and CD/USB/SD:
discrete resistors. AUX1:
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
discrete capacitors.

NM : No Mount

The > mark found on some component parts indicates

2
2

the importance of the safety factor of the part.

Therefore, when replacing, be sure to use parts of
identical designation.

DEH-22UB/XSUC
3
3

FM(10%):-33.5 dBs
AM(15%):-30.0 dBs

FM/AM TUNER UNIT

4
4

PN5035B
 PN5035B
5

5
6
6

DEH-22UB/XSUC
7
7

AUX1(-20 dB):-17.8 dBs

8

8
B CN1821
A-a A-b

A-a
A-b

45
E
A

D
C

F
B
 1 2 3 4

10.2 KEYBOARD UNIT

B KEYBOARD UNIT

5.00 MHz
PD6340A

C
CLOCK
NM

SR CD
CL
CL-195SR-CD
DS2XA4WBETW1(Z1)

B
DEH-22UB/XSUC
46
1 2 3 4
 DS2XA4WBETW1(Z1)

LOCK
CL-195SR-CD
CL-195SR-CD CL-195SR-CD

820(1/4W)

CL-195SR-CD
5

5
CL-195SR-CD CL-195SR-CD

820(1/4W)

AUX
CL-195SR-CD
CL-195SR-CD CL-195SR-CD

PWR/VOL
820(1/4W)

CL-195SR-CD
CL-195SR-CD CL-195SR-CD
AUX1:-17.8 dBs

6
6

680(1/4W)

CL-195SR-CD CL-195SR-CD

1k(1/4W)

CL-195SR-CD CL-195SR-CD

2.2k(1/4W)

DEH-22UB/XSUC
7
7

USB
8

8
A CN832

B
47
E
A

D
C

F
B
 1 2 3 4

10.3 CD MECHANISM MODULE(GUIDE PAGE)

A
C-a NOTE1) GND.... CD LSI, RFAMP, CPU
PGND...Actuator, Motor Driver
AGND...Audio
These GND's are not connected to each other on PCB.
PGND is connected to a floating mechanism part by a screw.

GND

C213

0.1u
PICKUP UNIT (P10.5)(SERVICE) V3R3
VDD VDD

CXX1942
E:P5+P10

R103
2.7

(1/10W)
F:P1+P6

(1/10SR,1608)
NM

R102
R106

2.4

NM
R108
(2125)
C106
R101

4.7u
2.4
Q102
LD1 UNR511MG
LD
Q101 R104
MD
LD

2SA1577

REFOUT
2.2k

4.7k
4.7k
VCC

1000p
NM

1000p
C102

D101

P3

R216

R214

108
107
106
105
104
103
102
101
100
NM

99
98
97
96
95
C251

C250
P7
LD- 10k
P9 F

IO GND
R221

RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
15 15

IO.VDD
RA11
RA10
PU+3V FD
LD+ FD
14 14 TD T R222 109
B+D
F BD TD
P5 13 13 SD C 10k 110
VCC SD
P10 12 12 S 111
MD
MD
C110

P5+P10
NM

11 11 C216 R225 112

GND EFM
GND 3300p

R226
10k

39k
P1 10 10 113
REFO1 C218
1MEG

ASY
C105

C111

R107

P1+P6
NM

P6
NM

9 9 114
0.047u ATEST ATEST
VREF
8 8 115
P2 T A.VDD1
VR F C217 0.1u
P4 7 7 116
A+C F AC A.GND1
P8 NM
6 6 R236 C220 1800p 117
MD PD RFI
5 5 118
TOM
PD T TOM RFAGC AGCO
4 4 C219 0.1u 119
HOLOGRAM UNIT F C3T
FOM FOM C221 120

4p
3 3
f RFO

5.6k
R227
FOP F FOP AGCI
2 2 0.1u 121

C223
FOCUS ACT T 22p RFO
TOP TOP C239
1 1 R232 122
TRK ACT EQ2
1.2k 123
CN101 C222
56p R228 124
EQ1
CKS4808

R229
1.2k

4.7k
RF2-
125
T E RF-
126
F.ACT:Applying positive voltage to FOP. A.GND2
C224 0.1u 127
the lens moves DISC side. A.VDD2
AC A+C F 128
T.ACT:Applying positive voltage to TOP.
C the lens moves outer circumference. BD B+D F 129
A
B
F F T 130
F
E E T 131
E
REFOUT 132
REFOUT
C229 0.1u C226 133
C236 FE-
(12) 68p 134
0.1u FE FEO
c ADIN
C227
135
136
ADCIN
TE-
(13) 47p 137
d TE
C228 R291 138
TEO
TE2

2 /USBXTAL
1 USBXTAL
0.01u 2.7k 139
TEC TEC
140
LD
PD 141
M1 CXE2273 C240 142
PD

ADC GND
ADC.VDD
DSCSNS
VDSENS
AD.VDD

/12SNS
/HOME
SPINDLE MOTOR

GNDQ

VDDQ
/8SNS

TEMP
0.1u 143
AD.GND

DM
DP
C293 144

1
2
3
4

6
7
8
9
5

10
11
12
13
14
BLK 1000p
S SOM

0.1u
R294
220

0.1u

TEMP
48.000 MHz

C260

C202
RED S SOP X205

R235
CSS1753
1 3

C263
D X203

NM
NM
2
PL C LCOM
C261

C262
3p

3p

24
24
R282
R283
OG C

DSCSNS
VDSENS
LCOP R285 15k

FLMD0
HOME
8EJ
R284 15k
M2 CXC4026
DM
DP
LOADING/CARRIAGE
MOTOR Land for manual soldering

100k
100k
R261 100k
MOTOR DRIVER LOGIC TABLE
0

LOAD EJ PLAY OFF

R259

R256
R254
CLCONT H H L L
REFO2 LOEJ L H - -
CONT L L H L
REFOUT

IC301
NM

NM

MDX MDY
1 28
e
0.022u

VR PreVcc
C304

3 T
C203

2 27
R203

TD
(1608)

OPIN2+ R310 S MD
OPIN3+
9 3 OPIN2- 26

7
NM
R309

R258

OPIN3- 18k
18k

HOME 4 OPOUT2 25
TIN OPOUT3 SIN
S901 F 5 24 R308 C SD
HOME FD OPIN1+
TH201

E NC
NM

HOME OPINSL
13 4

4700p
C303

a
R307

8
6 23 18k
18k
2

4
OPIN1-
LOEJ
NC
CSN1067-A 2 FIN
7
OPOUTSL
OPOUT1
LDIN
22 CIN

LOEJ

8SNS 29 30
FIN1 FIN2 CLCONT
5
PGND

S905
PGND

NC 8SNS
13 4

8EJ
8 21 CLCONT
2

NC GND1 CNT
FOM
TOM

9 20
FOP

TOP

CSN1068-A CONT MUTE GND2

C307 10 19
1 FOP F 1u 11
PowVcc1
PowVcc2
18 C
VO1- VO4-
FOM F (1608) 12 17 C
DSCSNS VO1+ VO4+
S903 TOM T 13 16 S
NC DSCSNS DSCSNS T
VO2- VO3-
S
13 4

TOP 14 15
2

VO2+ VO3+ VDSENS

NC C306
VD

VD

CSN1068-A BA5839FP VDSENS

NM
C305
R240 47k

SWITCHES:
(1608)
LCOM
LCOP
SOM
SOP

NM
CD CORE UNIT
R241
10k

S901:HOME SWITCH.........ON-OFF
C308
CONT

S903:DSCSNS SWITCH.....ON-OFF
S905:8EJ SWITCH..............ON-OFF NM
(1608) VD VD
The underlined indicates the switch position. USBGND

GND GND
F
C711
C708

C709

C710

0.1u
NM
NM

NM

PGND

C
DEH-22UB/XSUC
48
1 2 3 4
 5 6 7 8

C-b A

GND C CD CORE UNIT (S11USB)

C213

0.1u

VDD

SIGNAL LINE
F FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

B
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
b
/RAS
(CKE)
IO.GND

/OE(/CAS)

/CAS1(UDQM)
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
IO.VDD

RDB9
RDB8
RDB7
RDB6
RDB5
RDB4
RDB3
RDB2
RDB1
RDB0

/CAS0(LDQM)
/WE
RDB15
RDB14
RDB13
RDB12
RDB11
RDB10

72
71
SVMON3 RFOK
70
SVMON2 LOCK
69
SVMON1 HOLD
72 (/RCS) 68
71 C33M SVMON0 MIRR
67
DOUT DOUT
66
SCKO SCKO C215
65 0.1u
LRCK LRCK
64 C212
REG16
63 C214 NM (1608)
D.VDD
62 0.1u
D.GND
61 C211
DA.VDD2
60 0.1u ROUT
ROUT
59 C209

C601
DA.GND2

NM
NM
IC201 REGC
58 22u C230
(1608)
AGND
57

C602
DA.GND1 0.1u

NM
C210
56 LOUT
LOUT C208 NM
55
PE5715A DA.VDD1
54
0.1u
C207 (1608)
X.VDD
53
3

/XTAL
52 R237 470 X201
C
X.GND
2

(uPD63790CGJ) 51 CSS1603
XTAL 16.934 MHz
50
1

C206
C.GND
49
C.VDD 0.1u
48 (2125)
REGS
47 C205 4.7u
BRST
/BRST
46
TEST
45 MASK/FLASH
PPON OCI
44 R223 C243
34 ROMDATA

OCI MASK NM
43 C243 47k
35 ROMCK
36 ROMCS

(2125) FLASH 4.7u

F_REGC
42 NM R210 CONT
CONT
41 1k
CD3VON CD3VON
CPSEL(/EJSW)

40 PUEN
/PUEN
39
ADC.GND
ADC.VDD
DSCSNS
VDSENS

CLCONT

LRCKOK
/TESTIN

LRCKOK
/ADENA

/CPRST
/RESET

CPRDY
/12SNS

BRXEN
/HOME

FLMD0

/BSRQ
/BSCK

CDMUTE(MCKRQ)
VDDQ
/8SNS

TEMP

38
FRxD

LOEJ
FTxD

ROM
BSO

SDA
SCL

CDMUTE
BSI
DP

37
6
7
8
9
5

10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

l
0.1u

m
0.1u

CPRDY
FLMD0

RX

SDA
TEMP

SCL
TX

CPRST
TESTIN

BSCK2
C260

C202

R235

IC202
k
C201 NM
47k

1 8
R233
10k

CS VCC
D
(1608)

2 7
SK NC
0.01u
220

3 6 R243
DI TEST
R201 4 5 NM
24
24

DO GND
C204

(1608)
R204

NM
R282
R283

R249

R206

100k

(1608)
NM

NM
R234

R202
DSCSNS
VDSENS

CLCONT

47k
47k
BRXEN
RESET

BDATA
FLMD0
HOME

BSRQ
BSCK

LOEJ
8EJ

RX
TX
DP

RX
TX
RESET
FLMD0

VDD VDD
R244
100k
100k

GND
R261 100k
0

R208 47k
CN704
10

R245
4

8
2

NM
R259

R256
R254

ROM

NM
A
R209

NM

NM
GND CN701
CKS5854
CN651
C704 1000p

100p

NM
3
5

9
7

NM
1

NM

(1608)

VD_2

VD_1
NM
(1608)
R280

R290

VDD
10k
10k

MSC MODEL ONLY

6
C703

C705

C730
C702

C706
NM

1
NM

VD 7.5V
VD
2 VD 7.5V
BSRQ
C203

R203

R293

BSRQ
(1608)

4.7k

3 /BSRQ
BRST R701 BRST
NM
R258

VDD

4 /BRST
R207

R702 BSCK
0

BSCK 220
R250 100

R252 100

Q201 5 /BSCK
BRXEN 220 BRXEN
2SA1577(QR)
TH201

E
NM

6 BRXEN
BDATA BDATA
7 BDATA
R273 10k RESET RESET
8 /RESET
VDD_2 VDD
R277 10k 9 VDD 3.3V
GND C707
10 GND GND
ROUT
IC205 NM 11 ROUT
341S2162 AGND
12 AGND GND
17
19
18

16
20

LOUT
SWVDD

R292
2.7k

13 LOUT
AGND1

AGND2

ROUT
LOUT
NC13
NC12
NC11
NC10

NC9

14
h
GND GND
g DP2 DM2
i
11 12 13 14 15

1
NC8 15 PGND GND
NC1 DP
SWVDD

2 MODE0/SPI_CLK DP
MODE1/SPI_nSS 16 DP
3 DM DM
NC2 I2C_SDA/SPI_SOMI 17 DM
C294 I2C_SCL/SPI_SIMO R714
4 18
nRESET USBGND GND
0.1u 0
j
5 VCC VSS 19
NC3

NC5
NC6

10 NC7
NC4

(1608) USBGND GND

I/O
R295

C290
47k

0.1u

7
8
6

NM iPod CONNECTED MODEL ONLY

VD
USBGND
USBGND USBGND

GND4 GND3 GND1

GND GND
F
C701

PGND2 PGND1
NM

PGND PGND

C
DEH-22UB/XSUC
5 6 7 8
49
 F
E
B
A

D
C

50
C-a C-b

C-b
1
1

GND C CD CORE UNIT (S11USB)

0.1u

C213
VDD

SIGNAL LINE
F FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

2
2

103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73

RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0
/WE
/RAS
b

(CKE)

RDB9
RDB8
RDB7
RDB6
RDB5
RDB4
RDB3
RDB2
RDB1
RDB0
72

RDB15
RDB14
RDB13
RDB12
RDB11
RDB10

IO.VDD
IO.GND
/OE(/CAS)
71
SVMON3 RFOK

/CAS0(LDQM)
/CAS1(UDQM)
70
SVMON2 LOCK
69

DEH-22UB/XSUC
SVMON1 HOLD
72 (/RCS) 68
71 C33M SVMON0 MIRR
67
DOUT DOUT
66
SCKO SCKO C215
65 0.1u
LRCK LRCK
64 C212

3
3

REG16
63 C214 NM (1608)
D.VDD
62 0.1u
D.GND
61 C211
DA.VDD2
60 0.1u ROUT
ROUT
59 C209
DA.GND2 NM
C601
NM

58 22u C230 AGND

IC201 REGC (1608)
57
DA.GND1 C210 0.1u
C602
NM

56 LOUT
LOUT C208 NM
55
PE5715A DA.VDD1 0.1u
54 C207 (1608)
X.VDD

3
53
/XTAL
52 R237 470 X201
X.GND

2
(uPD63790CGJ) 51 CSS1603
XTAL 16.934 MHz
1
50
C206
C.GND
49
C.VDD 0.1u
48 (2125)
REGS
47 C205 4.7u
BRST

4
4

/BRST
46
TEST
45 MASK/FLASH
PPON OCI
44 R223 C243
OCI MASK NM
43 C243 (2125) 47k
F_REGC FLASH 4.7u
42 NM R210 CONT
CONT
41 1k
CD3VON CD3VON

34 ROMDATA
35 ROMCK
36 ROMCS
40 PUEN
/PUEN
39
LRCKOK LRCKOK
CDMUTE(MCKRQ) 38
CDMUTE

DP
VDDQ
/8SNS
/12SNS
/HOME
DSCSNS
VDSENS
TEMP
ADC.VDD
ADC.GND
FLMD0
/RESET
/ADENA
CPSEL(/EJSW)
/TESTIN
CLCONT
BSI
BSO
/BSCK
FTxD
FRxD
BRXEN
/BSRQ
LOEJ
ROM
CPRDY
/CPRST
SDA
SCL
37

6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

l
 OCI MASK NM
43 C243 (2125) 47k
F_REGC FLASH 4.7u
42 NM R210 CONT
CONT
41 1k
CD3VON CD3VON

34 ROMDATA
35 ROMCK
36 ROMCS
40 PUEN
/PUEN
39
LRCKOK LRCKOK
CDMUTE(MCKRQ) 38
CDMUTE

DP
VDDQ
/8SNS
/12SNS
/HOME
DSCSNS
VDSENS
TEMP
ADC.VDD
ADC.GND
FLMD0
/RESET
/ADENA
CPSEL(/EJSW)
/TESTIN
CLCONT
BSI
BSO
/BSCK
FTxD
FRxD
BRXEN
/BSRQ
LOEJ
ROM
CPRDY
/CPRST
SDA
SCL
37

6
7
8
9
10
15
16
17
18

11
12
13
14
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
l

0.1u
TX
RX
m

SCL
SDA

TEMP
FLMD0
CPRDY

C202
CPRST

TESTIN
BSCK2
5

5
R235
IC202
k

47k
1 8
CS VCC

10k
2 7

R233
SK NC

C201 NM
(1608)
3 6 R243

220
0.01u
DI TEST
R201 4 5 NM

24
DO GND
NM (1608)
(1608)

C204
R204
NM
NM

R283
R249
100k

R206
47k

47k
R234
R202

8EJ
HOME
DSCSNS
VDSENS
FLMD0
RESET
CLCONT
BDATA
BSCK
TX
RX
BRXEN
BSRQ
LOEJ
TX
RX
VDD VDD
R244

FLMD0
RESET
GND

100k

100k
R208 47k

4
8

2
6
R245 CN704
10
NM
NM
NM

R261 100k
R256
R254
ROM

NM

R209
GND CN701
CKS5854
A

6
6

3
5
9
7

1
CN651
NM
NM

NM

VDD
NM

100p

10k

10k
MSC MODEL ONLY
VD_2
VD_1

R280
R290
(1608)
(1608)

6
1 VD 7.5V
C704 1000p
C703

NM
C705
C730

NM
C702
C706

VD
2 VD 7.5V
BSRQ BSRQ
3 /BSRQ

C203
R203
R293
4.7k
BRST R701 BRST

(1608)
4 /BRST

NM
R702 220 BSCK

VDD
BSCK
5

R207
Q201 /BSCK
BRXEN 220 BRXEN
2SA1577(QR)
6 BRXEN

NM
BDATA BDATA

R250 100
R252 100

TH201
7 BDATA
R273 10k RESET RESET
8 /RESET
VDD_2 VDD
R277 10k 9 VDD 3.3V
GND C707
10 GND GND
ROUT
IC205 NM 11 ROUT
341S2162 AGND

DEH-22UB/XSUC
12 AGND GND
LOUT

17

19
18
16

20
13 LOUT

2.7k
R292
14 GND GND

SWVDD
ROUT

DP2 DM2
LOUT

NC9
AGND1
AGND2

NC13
NC12
NC11
NC10
NC8 g h i 15 PGND GND

7
7

NC1 DP
2 MODE0/SPI_CLK DP
MODE1/SPI_nSS 16 DP
3 DM DM

SWVDD
NC2 I2C_SDA/SPI_SOMI 17 DM
C294 I2C_SCL/SPI_SIMO R714
4 18 USBGND
nRESET GND
0.1u 0

11 12 13 14 15
5 VCC VSS
(1608) 19 USBGND GND
j

NC3
NC5
NC6

NC4
7
8

6
9
10 NC7
I/O

47k
0.1u

R295
C290
NM iPod CONNECTED MODEL ONLY
D
USBGND
SBGND USBGND

GND4 GND3 GND1

ND GND

PGND2 PGND1
NM

GND PGND
C701
8

8
C-a C-b

C-b
51
E
A

D
C

F
B
 F
E
B
A

D
C

52
C-a C-b

C-a
C-b
NOTE1) GND.... CD LSI, RFAMP, CPU
PGND...Actuator, Motor Driver

1
1

AGND...Audio
These GND's are not connected to each other on PCB.
PGND is connected to a floating mechanism part by a screw.

GND
C213

PICKUP UNIT (P10.5)(SERVICE) VDD VDD

V3R3

CXX1942
E:P5+P10

2.7
R103
F:P1+P6

(1/10W)
NM
R106

R102
2.4
(1/10SR,1608)
NM

2
2

R108

2.4
4.7u

C106

R101
(2125)
Q102
LD1 UNR511MG
LD
Q101 R104

MD
LD
2SA1577
2.2k
VCC
4.7k

4.7k

NM
REFOUT
P3
1000p

1000p

C102
NM

D101
108
107
106
105
104
103
102
101
100
99
98
97
96

P7
R216
R214

LD- 10k
C251
C250

P9 15 15 F R221
PU+3V FD
FD
RA9
RA8
RA7
RA6
RA5
RA4
RA3
RA2
RA1
RA0

LD+
RA11
RA10

14 14 TD T R222 109
B+D
F BD TD
P5 13 13 SD C 10k 110
VCC SD
P10 12 12 S 111
MD
P5+P10 MD
11 11 C216 R225 112

NM

C110

DEH-22UB/XSUC
GND EFM
GND 3300p
P1 10 10 10k 113
39k

REFO1 C218 ASY

R226

P6 P1+P6
9 9 114

NM

NM

C105
C111
ATEST

R107
1MEG
VREF 0.047u ATEST
8 8 115
P2 T A.VDD1
VR F C217 0.1u
P4 7 7 116
A+C F AC A.GND1
P8 6 6 NM
R236 C220 1800p 117

3
3

MD PD RFI
5 5 118
PD T TOM RFAGC AGCO
TOM
4 4 C219 0.1u 119
HOLOGRAM UNIT F C3T
FOM FOM C221 120
4p

3 3 RFO
FOP F FOP f AGCI
5.6k

2 2 0.1u 121
R227

FOCUS ACT T 22p RFO

TOP TOP C239
1 1 R232 122
C223

TRK ACT EQ2

C222 1.2k 123
CN101 EQ1
56p R228 124
CKS4808 1.2k RF2-
125
4.7k

R229

T E RF-
126
F.ACT:Applying positive voltage to FOP. A.GND2
C224 0.1u 127
the lens moves DISC side. A.VDD2
AC A+C F 128
T.ACT:Applying positive voltage to TOP. A
BD B+D F 129
the lens moves outer circumference. B
F F T 130
F
E E T 131
E
REFOUT 132
REFOUT
C229 0.1u C226 133
C236 FE-
(12) 68p 134
0.1u

4
4

FE FEO
135
c ADIN ADCIN
C227 136
TE-
(13) 47p 137
TE TEO
d C228 R291 138
TE2
0.01u 2.7k 139
TEC TEC
140
LD
PD 141
1 USBXTAL
2 /USBXTAL

PD
M1 CXE2273 C240 142
AD.VDD
SPINDLE MOTOR 0.1u 143
AD.GND
C293
GNDQ
DM
DP
VDDQ
/8SNS
/12SNS
/HOME
DSCSNS
VDSENS
TEMP

144
1
2
3
4
6
7
8
9

1000p
10
11
12
13

BLK S SOM
 p
TE TEO
d C228 R291 138
TE2
0.01u 2.7k 139
TEC TEC
140
LD
PD 141

1 USBXTAL
2 /USBXTAL
PD
M1 CXE2273 C240 142
AD.VDD
SPINDLE MOTOR 0.1u 143
AD.GND
C293

GNDQ
DM
DP
VDDQ
/8SNS
/12SNS
/HOME
DSCSNS
VDSENS
TEMP

144

1
2
3
4
6
7
8
9

5
1000p
10
11
12
13

BLK S SOM
0 1u

220
R294
48.000 MHz
0.1u

RED S SOP X205

TEMP

C260
C202
5

5
CSS1753
1 3
X203
NM

NM
C263

2
PL C LCOM
3p
3p
24
24

C261
C262
R282
R283

OG C LCOP R285 15k

R284 15k
8EJ
HOME
DSCSNS
VDSENS

DM
DP

M2 CXC4026
LOADING/CARRIAGE
MOTOR Land for manual soldering
0

MOTOR DRIVER LOGIC TABLE

100k

100k

LOAD EJ PLAY OFF

CLCONT H H L L
R259
R261 100k
R256
R254

REFO2 LOEJ L H - -
CONT L L H L

6
6

REFOUT

IC301
MDX MDY
NM
NM

1 28
VR PreVcc
TD T 2 27 e
0.022u

OPIN2+
C304
3 OPIN3+ R310 S MD
C203
R203

3 26
(1608)

OPIN2- 18k
9 OPIN3-
NM

18k

HOME 4 25 7
R309
R258

TIN OPOUT2 SIN

S901 OPOUT3
FD F 5 OPIN1+ 24 R308 C SD
NC HOME HOME OPINSL
6 23 18k

2
OPIN1-
TH201

18k
C303

a LOEJ

13 4
NC
R307
4700p

CSN1067-A 2 7
OPOUTSL
OPOUT1 22 CIN 8 4
FIN LDIN
LOEJ

8SNS 29 30
FIN1 FIN2 CLCONT
S905 5
NC 8SNS 8EJ
PGND

PGND
8 21

2
CLCONT

DEH-22UB/XSUC
NC GND1 CNT

13 4
9 20
CSN1068-A CONT MUTE GND2

FOP
FOM
TOM
TOP
C307 10 19
PowVcc1
1 F 1u PowVcc2 C
FOP 11 18
VO1- VO4-

7
7

FOM F (1608) 12 17 C
DSCSNS VO1+ VO4+
S903 TOM T 13 16 S
NC DSCSNS VO2- VO3-
DSCSNS TOP T 14 15 S

2
VO2+ VO3+ VDSENS
NC

13 4
C306
CSN1068-A
VD
VD

BA5839FP NM VDSENS
C305
SWITCHES:
NM
(1608)

CD CORE UNIT
SOM
SOP
LCOM
LCOP
10k

R240 47k
R241

S901:HOME SWITCH.........ON-OFF
C308
S903:DSCSNS SWITCH.....ON-OFF
CONT

S905:8EJ SWITCH..............ON-OFF NM
(1608) VD VD
The underlined indicates the switch position. USBGND

GND GND
0.1u

C711

C708
NM

C709
C710

NM
NM

PGND
8

8
C-a C-b

C-a
C-b

53
E
A

D
C

F
B
 1 2 3 4

10.4 WAVEFORMS

- CD CORE UNIT Note : 1. The encircled numbers denote measuring points in the circuit diagram.
A
2. Reference voltage REFO1(1.65 V)

DSCSNS 5 V/div 500 ms/div DSCSNS 5 V/div 500 ms/div DSCSNS 5 V/div 500 ms/div
8SNS 5 V/div CLCONT 5 V/div 8SNS 5 V/div
12SNS 5 V/div LOEJ 5 V/div 12SNS 5 V/div
LOEJ 5 V/div VD 10 V/div LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:

GND GND GND
B
Mode: Mode: Mode:
Normal Normal Normal

SIN 1 V/div 1 s/div FIN 200 mV/div 500 ms/div TE 500 mV/div 200 ms/div
CIN 500 mV/div RFOK(MONI_2) 2 V/div FE 500 mV/div
TIN 1 V/div SIN 2 V/div

12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

FE 500 mV/div 20 ms/div MDX 2 V/div 200 ms/div MDX 2 V/div 5 us/div
FIN 500 mV/div SIN 500 mV/div SIN 500 mV/div
TE 500 mV/div
D TIN 500 mV/div
CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

Normal Normal Normal

E
FIN 500 mV/div 200 ms/div TE 500 mV/div 2 ms/div RFAGC 1 V/div 500 us/div
FE 500 mV/div RFAGC 500 mV/div TE 500 mV/div
TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

F TEST TEST TEST

DEH-22UB/XSUC
54
1 2 3 4
 5 6 7 8

A
RFAGC 1 V/div 500 us/div RFAGC 1 V/div 500 us/div RFAGC 1 V/div 2 ms/div
TE 500 mV/div TE 500 mV/div TE 500 mV/div
TIN 500 mV/div TIN 500 mV/div TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:

REFO REFO REFO

Mode: Mode: Mode:

TEST TEST TEST B

RFAGC 1 V/div 200 ms/div LOUT 1 V/div 200 us/div DSCSNS 5 V/div 500 ms/div
TE 1 V/div ROUT 1 V/div 8SNS 5 V/div
CIN 1 V/div HOME 5 V/div
SIN 2 V/div LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

Ref.: Ref.: Ref.: C

REFO AGND GND

Mode: Mode: Mode:

Normal Normal Normal

DSCSNS 5 V/div 500 ms/div DSCSNS 5 V/div 500 ms/div RFAGC 1 V/div 500 us/div
CLCONT 5 V/div 8SNS 5 V/div TIN 1 V/div
LOEJ 5 V/div HOME 5 V/div TE 1 V/div
LOEJ 5 V/div FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 um) during play D

Ref.: Ref.: Ref.:

GND GND REFO

Mode: Mode: Mode:

Normal Normal Normal

DP 1 V/div 50 ns/div DP 2 V/div 50 ms/div DP 1 V/div 50 ms/div

DM 1 V/div DM 2 V/div DM 1 V/div E

USB Play USB device inserting to USB connector. CD Play with USB(iPod) device connecting.

Ref.:
USB
Ref.: Ref.: GND
USB USB
GND GND

DEH-22UB/XSUC
5 6 7 8
55
 1 2 3 4

A
DP 2 V/div 50 ms/div CPRST 2 V/div 500 ms/div
DM 2 V/div SDA 2 V/div
SCL 2 V/div

ACC OFF with USB(iPod) device connecting. iPod Authentication Operation

Ref.: Ref.:
USB GND
GND

DEH-22UB/XSUC
56
1 2 3 4
5 6 7 8

DEH-22UB/XSUC
5 6 7 8
57
 1 2 3 4

11. PCB CONNECTION DIAGRAM

11.1 TUNER AMP UNIT
A NOTE FOR PCB DIAGRAMS
1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
several destination. 150
For further information for
respective destinations, be sure
W.REM
to check with the schematic dia-
CN941
RCA
gram.
CN251

C942
C941
2.Viewpoint of PCB diagrams 140 1 5

Connector Capacitor C351 C337

C313 C336

R942

R303
R302
R941
Q301 1

C255

C252
C251

R253
Q252

R251
Q251

R256

R254

R252
C256
R255

R257
1 1 R301
SIDE A

FU251
R258
C259

1
C253

1
R352
130 Q351 C258 C257 R353 C335

C254

1
B C501 D501
R351
C712
IC712
SIDE B

1
P.C.Board Chip Part C711
R507 C505
120 R506
C506
R505 R504

5
C503
R501 R503
IC501 L501
C502 C504
R502

1
110 D502

1
100
C

90

80

70

60

50

40

30

20

10

F Y

0
A X 10 20 30 40 50 60

DEH-22UB/XSUC
58
1 2 3 4
 5 6 7 8

A
SIDE A
> FU 251 (A,5,129) Fuse 3 A CEK1286

IC301

10 20 CORD ASSY
JA901
E
L902 Q751
C337
10
C313 C336
R303
R302

1
Q301 R751 D751
1 5 15 25
C752
C305

R301
C306

C307

C308

C312 C751
1

R352 C310
C309
1
C335 C332 1 C311 5 15
C257 R353 D301
C301
C302

C304

C333
C303

C901 Q752
R852
R851
R333 R332
R351 Q851 L851 B
C331
R331 C334 R334 D901
ANTENNA
D851
ANT401
E

R854 R853

R855
D902
D302 R923 C952
R612
C202
C204 D951
C951 CN402
D952
C672 5 1

1
C206
20
R206

15
R222

C212 C953 AR401

C651
L201 IC951
IC201
C213 R925 E
Q921
R213 C205 C214 10 R951 C404 Z401
R221 C207

R924
1 5 10 R921

1
R207

C921
C215

D921

R922
C203 5
C201 D601 R692
R681 L620
R678 C216 C647
C671

R643
R615

R679 L602 IC691

D602 C405 L402
R680 R201 R691
R685 R605
R617 R616
R686 1 C402
C

5
R619
R687 R618
R677 R674 C633
R404 C409 R408 C618
R676 C412

CN602 C632
1
140 130 120 110 R409
R410
C416
C601

R406 C614
R601 R412 R411
L601

R407
C603 R413 C635 R666
100 R609
C608

R604
C602

10 C683
R613 L617

FM/AM TUNER UNIT

R665

10
C622

L606
R712
L607

L621
R661 IC601 X601
R664 R662 90
C620

20
R622

R620
R663

C619
C641
C645
L613

R688 R602 R608 C628

Q680 R683 30 80 C629 L610
C630
1

C704 R611 C642

C623
R689 C624 C625
C653 40 50 60 70 C617 L608
C627
R659 L605 L611
C640 C616 R623 L609
C612
C607

L612
R816
R836

R672
C639
C605
R657

R660
R656

R610
R655

L614 C410
R818
R675

R603

L615
C631

L604 C626 C636

L618 C615 C407
C681
C682
L603 C609
E
C403 D
C606 C611 Q601
X681
R606
C637

L616
L619 C638

C613
D911 C621 C401
C912
C411
15

C408 L403
D912 R401
L401

C610
CN651 R607
C415
C406
1

L702 C909 C414

C915
1 C914 R405
C916 C413
20

L701 C650
5

L903 C417
Q801 R916
C910
R802
E
R702

C911 C913
C917
C703
R701

C CN701 R820
Q804 C919
R807

R809 C918
10

C813 R803
R808 C920 10 5 1
E

E
R708

R704 R801
C702

E
C812 IC911
R703 Q802
E
15

Q803
C815
L801
C817 C816 R817
R806
C804 C803
C814
R814
R813
R812

R815

D805 D807
C820
R837 C821
R831
C801

R811
R810

C819
R832

C802

C806 D806 C811

R819 C807 D801 D804
C808
R805
L802

D802 D803
C822
R804

C805 C810
C818

C809
S801

1
20
CN831 10

15 5 1
1 5 15

B CN1821
10 20
F
FRONT CN832

50 60 70 80 90 100 110 120 130 140 150 160

A
DEH-22UB/XSUC
5 6 7 8
59
 1 2 3 4

A TUNER AMP UNIT

1
1

A 160 150 140 130 120 110 100 90 80

DEH-22UB/XSUC
60
1 2 3 4
 5 6 7 8

A
SIDE B

150

1 140

130
B

120

110

100
C

90

80

70
D

60

1 50

40
E

30

20

10

F
Y

0
0 80 70 60 50 40 30 20 10 X A
DEH-22UB/XSUC
5 6 7 8
61
 F
E
B
A

D
C

62
B
B

1
1

KEYBOARD UNIT
11.2 KEYBOARD UNIT

DISP/BACK EJECT

2
2

S1844 S1843
D1869
D1870

40 D1888
D1889

D1884
S1842

D1865
1 2 S1841
S1821 SRC S1822 S1839 CLOCK
UPS1826 S1838 3
S1825
S1840

D1883
D1864
40 35 30 25 20 15 10 5 1
LCD1801

D1875
D1856

D1861
D1880
D1874
C1855
PWR/VOL

D1855
30 1 C1856

C1859

D1876

D1857
C1864 C1861
D1878 D1858 D1851
C1862 D1859 D1877
LEFT RIGHT
C1858 S1828

DEH-22UB/XSUC
C1865 S1827
20 S1824
S1845

D1852
D1871

D1881
D1862
C1866
S1823 C1852
AUX
C1863
6 CN1901

C1854
S1835 USB

C1853
5
LIST IC1802
BAND/ESC

D1872

3
3

D1853
S1834 S1829 S1830 4 CN1911
S1833

D1867
5

D1886
1
S1831 S1832

D1873
10 5

D1885
D1866
D1882
D1863
D1854
1

C1868

D1879
D1860
C1860
D1868
D1887
S1837 S1836
Y DOWN 1

0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
X

4
4

SIDE A
 B

F
C

D
A

63
B
SIDE B

8
8

C1870 A CN832
40
C1851 C1869
7

7
45 40 35
R1872
R1865 R1878 R1873
30
50

30

R1853 R1852

DEH-22UB/XSUC
D1802 D1801 C1857
R1801
R1802

R1860 R1859
55

R1858 X1801
25

IC1801 1
R1851 R1862 R1855
D1912
60

R1825
20

L1911 R1826
VA1902 VA1903 R1823
R1806

R1871
R19121

R1868
R1866
R1805

R1804
20
C1904
C1905
R1803

C1903
R1875 R1876
C1901 R1911 R1870 R1856
D1911 1 5 10 15 C1802
VA1901
R1901
VA1904

C1902
R1902

C1801 15 5 1
R1857 R1824

1
5
Q1851 R1863
R1864

R1867
R1869
R1854
CN1821 C1867 R1877 R1874
R1821
10
R1861
R1822
20 10
Y
6

6
0
160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
X
KEYBOARD UNIT

5
5

B
 1 2 3 4

11.3 CD CORE UNIT(S11USB)

A
C CD CORE UNIT(S11USB) SIDE A

B
PICKUP UNIT(P10.5)(SERVICE)

60

1
CN101 M2
15 10 5 1 TH201
S901
LOADING/CARRIAGE
C250 C251 HOME MOTOR
50
C102 REFO1 R225 C203
C216
R226
R221 R222 R203
M1
D101 F C218
SPINDLE
0
11

C217
MOTOR
10

C C220
5
5

CN704
11

C213
E C219
10
0
0

C221
1

12

95

C224
5
12
10
5

90

C226
40
0
13

85

C227
5
13

80

C240 R310
0

R308
14

75

IC201 C304 C303

X203 R309 R307
1

25 30 20 15
15

30 R294
C711
R282
10

C260 C214
15

70

R283
20

65

C201 IC301
25

C211
60

C202 R202
30

R261
55

D
35

C263 C208
R259
1

R254 C207
R258 R702 C206
50

10 R256 IC202 R243

45

R237
1 5 29 10
C204
20
40

C290 R701
5
5

1 R201
IC205 X201 C307
R204
15

R234 C708
1

20

10

CN701
E
Y 15 10 5 1 A CN651

0
10 20 30 40 50 60 70
X

C
DEH-22UB/XSUC
64
1 2 3 4
 5 6 7 8

C CD CORE UNIT(S11USB) SIDE B

A

R103

C110 R101
60
Q101 R102
C105
C111

C106
E

R104

R214
50
Q102 R107

R216 R108
R236 R227 C
C223
E R291
C239 R229
R106 C293
C222
R232 C228
R228

C261 40
X205
C229

1
C236

C305 C306
C262
C209
R235
C215
C212 R249
C601
30
R244 Q201
C230 R206 R284
R207
8EJ
1
C210 R209 R245
C602 R285
C205 S905
R208 R293 D
C710 C243 E
R233
R250
R292
R252
R280
R290
C709 C294
20

C703
C705
C730 R277
C707 C704 R273
R210 R223 R714
R241 C702
R295
C706 1 DSCSNS
R240
C701 S903 10
C308

Y
E

0
70 60 50 40 30 20 10
X

C
DEH-22UB/XSUC
5 6 7 8
65
 1 2 3 4

12. ELECTRICAL PARTS LIST

NOTE:
A Parts whose parts numbers are omitted are subject to being not supplied.
The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
Meaning of the figures and others in the parentheses in the parts list.
B Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
D 902 (A,127,117) Diode 1SR154-400
Unit Number : YWM5449
Unit Name : Tuner Amp Unit D 911 (A,113,56) Diode 1SR154-400
D 912 (A,113,53) Diode 1SR154-400
Unit Number : D 921 (A,123,106) Diode HZU6R2(B3)
L 402 (A,146,97) Inductor LCTAW2R2J2520
Unit Name : Keyboard Unit L 403 (A,146,57) Inductor CTF1473
C
Unit Number : CWX3776 L 501 (A,29,110) Choke Coil 47 uHCTH1420
L 602 (A,121,98) Inductor CTF1473
Unit Name : CD Core Unit(S11USB) L 606 (A,136,85) Chip Coil LCTAW1R0J2520
L 607 (A,133,83) Inductor CTF1379
L 608 (A,133,72) Chip Coil LCTAW1R5J2520

A
Unit Number : YWM5449
L
L
609
610
(A,134,70)
(A,136,77)
Chip Coil
Inductor
LCTAW1R5J2520
LCTAW1R2J2520
L 611 (A,138,71) Inductor CTF1379
Unit Name : Tuner Amp Unit L 612 (A,137,69) Inductor CTF1379
L 614 (A,122,69) Inductor CTF1379
MISCELLANEOUS
D
L 617 (A,132,85) Inductor CTF1389
IC 201 (A,102,109) IC PML014A L 618 (A,121,65) Inductor CTF1389
IC 301 (A,74,141) IC PAL007C L 701 (A,93,47) Inductor CTF1713
IC 501 (A,16,114) IC BD9007F L 702 (A,93,48) Inductor CTF1473
IC 601 (A,117,83) IC PN5035B L 801 (A,94,31) Inductor LCTAW2R2J2520
IC 712 (A,36,123) IC BD6538G
L 902 (A,107,140) Choke Coil 600 uHCTH1432
IC 911 (A,141,28) IC BA49181-V12 X 601 (A,141,78) Oscillator 74.1 MHzCSS1758
Q 251 (A,21,130) Transistor UMH3N X 681 (A,114,62) Oscillator 4.7186 MHzCSS1796
Q 351 (A,31,131) Transistor RT3T22M FU251 (A,5,129) Fuse 3 A CEK1286
Q 601 (A,136,63) Transistor 2SD1858 AR401 (A,145,110) Surge ProtectorIMSA-6802-01Y900
Q 751 (A,137,139) Transistor 2SD2396
E ANT401 (A,153,128) Antenna Jack CKX1070
Q 752 (A,136,128) Transistor RT3T22M CN251 (A,17,139) Pin Jack YKB5010
Q 801 (A,107,42) Transistor 2SA1036K CN651 (A,85,40) Connector CKS3833
Q 802 (A,107,38) Transistor RT1N141M-11 CN832 (A,105,3) Connector CKS6188
Q 921 (A,127,106) Transistor LSC4081UB JA 901 (A,109,141) Plug CKM1586
D 301 (A,93,128) Diode 1SR154-400
Z 401 (A,153,105) FM/AM Tuner UnitCWE2025
D 302 (A,113,114) Diode 1SR154-400
D 501 (A,17,125) Diode 1SR154-400 RESISTORS
D 502 (A,23,107) Diode RB160L-40
D 751 (A,135,132) Diode HZU7R5(B3) R 201 (A,118,97) RAB4CQ102J
D 801 (A,108,22) Diode MALS068X R 206 (A,90,112) RS1/16SS681J
R 207 (A,91,105) RS1/16SS681J
F D 802 (A,108,21) Diode MALS068X R 213 (A,90,107) RS1/16SS331J
D 803 (A,114,21) Varistor EZJP0V270RM R 221 (A,91,106) RS1/16SS223J
D 804 (A,115,22) Varistor EZJP0V270RM
D 901 (A,133,123) Diode 1SR154-400 R 222 (A,91,112) RS1/16SS223J

DEH-22UB/XSUC
66
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 251 (A,19,131) RS1/16SS223J R 680 (A,96,99) RS1/16SS273J
R 252 (A,24,131) RS1/16SS223J R 681 (A,95,101) RS1/16SS473J
R 253 (A,27,131) RS1/16SS821J R 683 (A,95,76) RS1/10SR473J
R 254 (A,17,131) RS1/16SS821J R 685 (A,101,97) RS1/16SS104J A

R 303 (A,59,132) RS1/16SS153J R 686 (A,104,97) RS1/16SS104J

R 331 (A,71,126) RS1/16SS471J R 687 (A,104,96) RS1/16SS104J
R 332 (A,79,128) RS1/16SS471J R 689 (A,93,74) RS1/16SS0R0J
R 333 (A,71,128) RS1/16SS471J R 702 (A,94,40) RS1/16SS221J
R 334 (A,78,126) RS1/16SS471J R 704 (A,92,37) RS1/16SS221J

R 351 (A,57,127) RS1/16SS103J R 708 (A,94,35) RS1/16SS104J

R 352 (A,55,130) RS1/16SS153J R 712 (A,94,84) RS1/16SS103J
R 353 (A,55,129) RS1/16SS221J R 751 (A,133,132) RS1/4SA271J
R 401 (A,145,55) RS1/16SS0R0J R 802 (A,109,42) RS1/16SS103J
R 404 (A,129,94) RS1/16SS102J R 803 (A,107,40) RS1/16SS562J
B
R 405 (A,147,47) RS1/16SS102J R 804 (A,98,22) RS1/10SR101J
R 406 (A,136,91) RS1/16SS102J R 805 (A,101,22) RS1/10SR101J
R 407 (A,136,90) RS1/16SS102J R 810 (A,96,26) RS1/10SR222J
R 408 (A,140,93) RAB4CQ104J R 811 (A,94,26) RS1/10SR222J
R 409 (A,131,92) RS1/16SS391J R 812 (A,111,26) RS1/10SR222J

R 410 (A,131,91) RS1/16SS681J R 813 (A,110,26) RS1/10SR222J

R 411 (A,133,91) RS1/16SS681J R 814 (A,113,26) RS1/10SR222J
R 412 (A,131,90) RS1/16SS681J R 815 (A,114,26) RS1/10SR222J
R 413 (A,131,89) RS1/16SS472J R 816 (A,92,71) RS1/16SS104J
R 501 (A,11,114) RS1/16SS473J R 817 (A,106,31) RS1/16SS473J

R 502 (A,11,113) RS1/16SS392J R 818 (A,94,69) RS1/16SS104J C

R 503 (A,22,113) RS1/16SS183J R 819 (A,90,21) RS1/16SS102J
R 504 (A,18,117) RS1/10SR4702F R 820 (A,103,41) RS1/10SR103J
R 505 (A,16,117) RS1/16SS682J R 831 (A,104,26) RS1/10SR222J
R 506 (A,16,120) RS1/10SR1002F R 832 (A,102,25) RS1/10SR222J

R 507 (A,18,120) RS1/10SR471J R 836 (A,91,71) RS1/16SS104J

R 601 (A,103,89) RS1/16SS473J R 837 (A,103,25) RS1/16SS222J
R 602 (A,101,78) RS1/16SS222J R 855 (A,93,120) RS1/16SS473J
R 603 (A,95,69) RS1/16SS473J R 921 (A,129,104) RS1/16SS104J
R 604 (A,132,87) RS1/16SS681J R 922 (A,125,106) RS1/16SS223J

R 606 (A,123,63) RS1/16SS473J R 923 (A,117,116) RS1/4SA102J

R 607 (A,110,49) RS1/16SS473J R 924 (A,120,106) RS1/16SS473J D
R 608 (A,131,79) RS1/16SS470J R 925 (A,121,108) RS1/16SS473J
R 610 (A,129,69) RS1/16SS473J
R 611 (A,131,76) RS1/16SS182J CAPACITORS
R 612 (A,88,115) RS1/16SS563J C 201 (A,93,103) CKSSYB224K6R3
R 613 (A,130,86) RS1/16SS302J C 202 (A,92,115) CKSSYB224K6R3
R 615 (A,92,102) RS1/16SS563J C 203 (A,93,104) CKSRYB105K6R3
R 616 (A,129,97) RS1/16SS104J C 204 (A,93,114) CKSRYB105K6R3
R 617 (A,116,96) RS1/16SS473J C 205 (A,110,105) 10 uF CCG1192

R 618 (A,129,95) RS1/16SS473J C 206 (A,93,112) CKSRYB105K6R3

R 619 (A,129,96) RS1/16SS104J C 207 (A,93,106) CKSRYB105K6R3
E
R 622 (A,132,80) RS1/16SS0R0J C 212 (A,93,111) CKSRYB105K6R3
R 623 (A,127,70) RS1/16SS0R0J C 213 (A,93,107) CKSRYB105K6R3
R 643 (A,128,99) RS1/16SS104J C 214 (A,116,105) 4.7 uF CCG1201

R 656 (A,101,70) RS1/16SS104J C 215 (A,113,106) CKSSYB104K10

R 657 (A,98,70) RS1/16SS104J C 216 (A,107,102) CCSRCH100D50
R 659 (A,103,71) RS1/16SS472J C 253 (A,43,130) CEVW2R2M50
R 660 (A,100,70) RS1/16SS472J C 254 (A,26,127) CEVW2R2M50
R 661 (A,103,83) RS1/16SS221J C 301 (A,70,129) CKSRYB474K10

R 666 (A,136,89) RS1/16SS103J C 302 (A,68,129) CKSRYB474K10

R 674 (A,102,94) RS1/16SS104J C 303 (A,76,128) CKSRYB474K10
R 675 (A,93,69) RS1/16SS473J C 304 (A,77,128) CKSRYB474K10 F
R 677 (A,99,94) RS1/16SS473J C 305 (A,71,132) CKSQYB474K25
R 678 (A,89,101) RS1/16SS103J C 306 (A,69,132) CKSQYB474K25

R 679 (A,99,100) RS1/16SS103J

DEH-22UB/XSUC
5 6 7 8
67
 1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 307 (A,75,131) CKSQYB474K25 C 711 (A,33,122) CKSRYB105K6R3
C 308 (A,76,131) CKSQYB474K25 C 712 (A,39,124) CKSRYB105K6R3
C 309 (A,82,127) CKSQYB225K10 C 751 (A,137,132) CKSSYB473K10
C 310 (A,84,127) CKSQYB225K10 C 752 (A,143,130) CEVW101M16
A
C 311 (A,98,128) CKSRYB104K16 C 802 (A,99,26) CKSRYB104K16

C 312 (A,64,129) CEVW100M16 C 803 (A,102,29) CCSRCH221J50

C 313 (A,53,135) CKSRYB104K16 C 804 (A,98,29) CCSRCH221J50
C 331 (A,69,125) CCSSCH101J50 C 805 (A,94,21) CKSRYB104K16
C 332 (A,79,129) CCSSCH101J50 C 806 (A,94,22) CKSRYB104K16
C 333 (A,71,130) CCSSCH101J50 C 807 (A,103,22) CKSRYB104K16

C 334 (A,76,126) CCSSCH101J50 C 808 (A,105,22) CKSRYB104K16

C 351 (A,47,136) CEVW330M10 C 809 (A,103,21) CKSRYB104K16
C 401 (A,146,58) CCSRCH270J50 C 810 (A,111,21) CCSRCH221J50
C 402 (A,143,96) CKSSYB103K16 C 811 (A,111,22) CCSRCH221J50
B C 404 (A,144,104) CEVW101M16 C 812 (A,103,38) CKSRYB104K16

C 405 (A,143,98) CKSSYB103K16 C 818 (A,96,22) CKSRYB104K16

C 409 (A,131,93) CCSSCH100D50 C 819 (A,91,23) CKSRYB104K16
C 416 (A,133,92) CCSSCH390J50 C 820 (A,91,26) CKSRYB104K16
C 501 (A,8,122) CEVW221M16 C 821 (A,119,26) CKSRYB104K16
C 502 (A,9,113) CKSQYB225K16 C 822 (A,90,22) CCSRCH221J50

C 503 (A,21,114) CCSSCH220J50 C 901 (A,128,125) 3 300 uF/16 V CCH1732

C 504 (A,23,113) CKSRYB153K50 C 909 (A,125,48) CKSRYB105K6R3
C 505 (A,26,119) CEVW221M10 C 910 4.7 uF CCG1201
C 601 (A,98,88) CKSRYB105K6R3 C 912 (A,119,54) CEAT102M16
C 603 (A,102,88) CKSSYB103K16 C 913 (A,132,41) CKSRYB104K16
C
C 605 (A,111,68) CKSSYB104K10 C 914 (A,130,45) 4.7 uF CCG1201
C 606 (A,103,63) CKSSYB103K16 C 915 (A,142,47) 4.7 uF CCG1201
C 607 (A,117,69) CKSRYB105K6R3 C 916 (A,142,44) 4.7 uF CCG1201
C 609 (A,129,66) CKSRYB331K50 C 917 (A,129,40) CKSSYB102K50
C 610 (A,104,49) CEVW101M4 C 953 (A,124,110) CCSRCH680J50

C
C
C
611
612
613
(A,129,65)
(A,119,69)
(A,99,57)
CKSRYB331K50
CKSRYB103K50
CEVW471M10
B
Unit Number :
C 614 (A,146,92) CKSSYB102K50
C 615 (A,129,68) CKSRYB331K50
Unit Name : Keyboard Unit
D C 616 (A,124,70) CKSSYB103K16 MISCELLANEOUS
C 617 (A,129,72) CCSRCH680J50
C 619 (A,137,81) CCSRCH180J50 IC 1801 (B,123,25) IC PD6340A
C 621 (A,135,60) CKSRYB331K50 IC 1802 (A,121,9) Remote IC GP1UXC14RK
C 622 (A,130,84) CKSRYB105K6R3 D 1801 (B,96,25) Diode MC2848-11
D 1802 (B,100,25) Diode MC2846-11
C 623 (A,131,75) CKSSYB102K50 D 1851 (A,163,23) White LED DS2XA4WBETW1(Z1)
C 624 (A,130,74) CKSSYB102K50
C 625 (A,134,74) CCSSCH270J50 D 1852 (A,62,21) LED CL-195SR-CD
C 626 (A,134,68) CCSSCH270J50 D 1853 (A,60,12) LED CL-195SR-CD
C 627 (A,136,72) CCSSCH150J50 D 1854 (A,68,11) LED CL-195SR-CD
D 1855 (A,77,33) LED CL-195SR-CD
C 628 (A,134,78) CKSSYB102K50 D 1856 (A,68,28) LED CL-195SR-CD
E
C 629 (A,132,78) CCSSCH4R0C50
C 630 (A,134,76) CCSSCH8R0D50 D 1857 (A,60,27) LED CL-195SR-CD
C 631 (A,118,68) CKSSYB223K16 D 1861 (A,26,28) LED CL-195SR-CD
C 632 (A,102,93) CKSSYB104K10 D 1862 (A,24,21) LED CL-195SR-CD
D 1863 (A,26,11) LED CL-195SR-CD
C 633 (A,120,96) CKSSYB104K10 D 1864 (A,13,30) LED CL-195SR-CD
C 635 (A,134,88) CKSSYB104K10
C 640 (A,122,70) CCSSCH680J50 D 1865 (A,7,37) LED CL-195SR-CD
C 650 (A,104,45) CKSSYB103K16 D 1866 (A,12,7) LED CL-195SR-CD
C 671 (A,91,102) CKSSYB182K50 D 1867 (A,89,8) LED CL-195SR-CD
D 1868 (A,77,6) LED CL-195SR-CD
C 672 (A,88,114) CKSSYB182K50 D 1869 (A,148,41) LED CL-195SR-CD
F
C 681 (A,114,66) CCSSCH270J50
C 682 (A,116,66) CCSSCH270J50 D 1870 (A,164,41) LED CL-195SR-CD
C 702 (A,95,35) CKSSYB103K16 D 1911 (B,150,17) Diode MALS068X
C 703 (A,93,39) CKSSYB104K10 D 1912 (B,148,23) Diode MALS068X
X 1801 (B,112,24) Ceramic Resonator 5.00 MHz CSS1731
DEH-22UB/XSUC
68
1 2 3 4
 5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
S 1845 (A,43,20) Rotary Switch CSD1153 R 107 (B,17,48) RS1/16SS105J

VA1901 (B,159,19) Varistor EZJZ1V270RM R 202 (A,47,25) RS1/16SS473J

VA1902 (B,157,21) Varistor EZJZ1V270RM R 204 (A,22,19) RS1/16SS221J A
VA1903 (B,154,21) Varistor EZJZ1V270RM R 206 (B,31,27) RS1/16SS104J
VA1904 (B,160,19) Varistor EZJZ1V270RM R 210 (B,51,12) RS1/16SS102J
LCD1801 (A,158,33) LCD CAW1970 R 214 (B,28,48) RS1/16SS472J

CN1821 (B,109,10) Connector CKS6049 R 216 (B,29,47) RS1/16SS472J

CN1901 (A,153,9) Jack YKN5001 R 221 (A,31,49) RS1/16SS103J
CN1911 (A,137,9) Connector YKS5036 R 222 (A,33,49) RS1/16SS103J
R 223 (B,38,14) RS1/16SS473J
RESISTORS R 225 (A,28,48) RS1/16SS103J

R 1802 (B,102,24) RS1/10SR2R2J R 226 (A,27,48) RS1/16SS393J

R 1803 (B,147,20) RS1/10SR103J R 227 (B,25,45) RS1/16SS562J
R 1804 (B,144,20) RS1/10SR101J R 228 (B,23,42) RS1/16SS122J B
R 1805 (B,99,23) RS1/10SR222J R 229 (B,23,44) RS1/16SS472J
R 1806 (B,101,21) RS1/10SR222J R 232 (B,25,43) RS1/16SS122J

R 1821 (B,57,8) RS1/10SR473J R 233 (B,19,24) RS1/16SS103J

R 1823 (B,95,22) RS1/10SR0R0J R 234 (A,48,18) RS1/16SS473J
R 1824 (B,29,15) RS1/10SR0R0J R 235 (B,23,32) RS1/16SS473J
R 1851 (B,156,24) RS1/4SA681J R 237 (A,42,22) RS1/16SS471J
R 1852 (B,68,28) RS1/4SA821J R 240 (B,49,10) RS1/16S473J

R 1853 (B,74,28) RS1/4SA821J R 241 (B,49,11) RS1/16SS103J

R 1855 (B,23,22) RS1/4SA821J R 244 (B,27,28) RS1/16SS473J
R 1856 (B,26,17) RS1/4SA681J R 254 (A,19,22) RS1/16SS104J
R 1857 (B,81,15) RS1/4SA102J R 256 (A,18,22) RS1/16SS104J C
R 1858 (B,154,24) RS1/4SA222J R 259 (A,12,23) RS1/16SS0R0J

R 1866 (B,68,18) RS1/10SR0R0J R 261 (A,14,24) RS1/16SS104J

R 1901 (B,158,19) RS1/10SR101J R 280 (B,30,20) RS1/16SS103J
R 1902 (B,156,19) RS1/10SR101J R 282 (A,15,28) RS1/16SS240J
R 283 (A,15,27) RS1/16SS240J
CAPACITORS R 284 (B,17,27) RS1/16SS153J

C 1801 (B,146,18) CKSYF106Z10 R 285 (B,18,27) RS1/16SS153J

C 1802 (B,85,16) CKSRYB105K10 R 290 (B,29,20) RS1/16SS103J
R 291 (B,16,44) RS1/16SS272J
C 1901 (B,154,20) CKSRYB472K50
C 1902 (B,154,18) CKSRYB472K50 R 294 (A,14,29) RS1/16SS221J
R 307 (A,60,33) RS1/16SS183J D

C
Unit Number : CWX3776
R
R
308
309
(A,60,35)
(A,58,33)
RS1/16SS183J
RS1/16SS183J
R 310 (A,57,36) RS1/16SS183J
Unit Name : CD Core Unit(S11USB) R 701 (A,36,21) RS1/16SS221J
R 702 (A,22,22) RS1/16SS221J
MISCELLANEOUS
R 714 (B,30,12) RS1/16S0R0J
IC 201 (A,31,33) IC PE5715A
IC 301 (A,64,27) IC BA5839FP CAPACITORS
Q 101 (B,9,56) Transistor 2SA1577
Q 102 (B,19,47) Digital TR(PNP) UNR511MG C 106 (B,12,54) CKSQYB475K6R3
E
X 201 (A,40,20) Ceramic Resonator 16.934 MHz CSS1603 C 202 (A,20,26) CKSSYB104K10
C 204 (A,21,20) CKSSYB103K16
X 205 (B,12,36) Oscillator 48.000 MHz CSS1753 C 205 (B,36,24) CKSQYB475K6R3
S 901 (A,42,53) Switch(HOME) CSN1067 C 206 (A,37,22) CKSSYB104K10
S 903 (B,21,12) Switch(DSCSNS) CSN1068
S 905 (B,11,25) Switch(8EJ) CSN1068 C 207 (A,40,22) CKSRYB104K16
CN101 (A,15,58) Connector CKS4808 C 209 (B,43,32) CEVW220M6R3
C 210 (B,40,27) CKSSYB104K10
CN701 (A,36,10) Connector CKS5854 C 211 (A,42,26) CKSSYB104K10
C 213 (A,38,44) CKSSYB104K10
RESISTORS
C 214 (A,44,27) CKSSYB104K10
R 101 (B,5,59) RS1/10SR2R4J C 215 (B,38,31) CKSSYB104K10 F
R 102 (B,7,59) RS1/10SR2R4J C 216 (A,26,49) CKSSYB332K50
R 103 (B,8,59) RS1/10SR2R7J C 217 (A,25,46) CKSSYB104K10
R 104 (B,12,52) RS1/16SS222J C 218 (A,26,48) CKSSYB473K10

DEH-22UB/XSUC
5 6 7 8
69
 1 2 3 4
Circuit Symbol and No. Part No.

C 219 (A,24,44) CKSSYB104K10

C 220 (A,24,45) CKSSYB182K50
C 221 (A,23,43) CKSSYB104K10
A
C 222 (B,23,43) CCSSCH560J50
C 223 (B,23,45) CCSSCH4R0C50

C 224 (A,21,42) CKSSYB104K10

C 226 (A,18,41) CCSSCH680J50
C 227 (A,18,39) CCSSCH470J50
C 228 (B,15,42) CKSSYB103K16
C 229 (B,23,37) CKSSYB104K10

C 236 (B,24,37) CKSSYB104K10

C 239 (B,25,44) CCSSCH220J50
C 240 (A,15,36) CKSSYB104K10
B C 250 (A,31,50) CKSSYB102K50
C 251 (A,33,50) CKSSYB102K50

C 260 (A,17,27) CKSSYB104K10

C 261 (B,9,38) CCSSCJ3R0C50
C 262 (B,9,34) CCSSCJ3R0C50
C 293 (B,15,43) CKSSYB102K50
C 303 (A,60,34) CKSSYB472K25

C 304 (A,58,34) CKSSYB223K16

C 307 (A,68,20) CKSRYB105K10
C 703 (B,36,14) CCSSCH101J50
C 704 (B,40,13) CKSSYB102K50
C C 711 (A,53,28) CKSSYB104K10

Miscellaneous Parts List

Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXE2273
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-22UB/XSUC
70
1 2 3 4