Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Pioneer DEH-P40MP PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 70

ORDER NO.

CRT3834
DEH-P40MP/XU/EW5

CD RDS RECEIVER

DEH-P40MP /XU/EW5

This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks

CX-3195 CRT3815 S10.5COMP2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly

For details, refer to "Important Check Points for Good Servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan


PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
K-ZZA. NOV. 2006 Printed in Japan
1 2 3 4

SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.

- Safety Precautions for those who Service this Unit.


• When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
B results.

Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.

CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CLASS 1
D
LASER PRODUCT

WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
E A specially instructed person should do servicing operation of the apparatus.

Laser diode characteristics


Wave length : 785 nm to 814 nm
Maximum output : 1 190 μW(Emitting period : unlimited)

Additional Laser Caution


Transistors Q101 in PCB drive the laser diodes.
F When Q101 is shorted between their terminals, the laser diodes will radiate beam.
If the top cover is removed with no disc loaded while such short-circuit is continued,
the naked eyes may be exposed to the laser beam.

DEH-P40MP/XU/EW5
2
1 2 3 4
5 6 7 8

CAUTION A
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
Discord used batteries according to the manufacture's instructions.

- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other B
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating. C
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.

DEH-P40MP/XU/EW5
5 6 7 8
3
1 2 3 4

[Important Check Points for Good Servicing]


In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
A
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.

1 Use specified parts for repair.

Use genuine parts. Be sure to use important parts for safety.

2 Do not perform modifications without proper instructions.

Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.

B 3 Make sure the soldering of repaired locations is properly performed.

When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)

4 Make sure the screws are tightly fastened.

Please be sure that all screws are fastened, and that there are no loose screws.

5 Make sure each connectors are correctly inserted.

Please be sure that all connectors are inserted, and that there are no imperfect insertion.

6 Make sure the wiring cables are set to their original state.

Please replace the wiring and cables to the original state after repairs.
C In addition, be sure that there are no pinched wires, etc.

7 Make sure screws and soldering scraps do not remain inside the product.

Please check that neither solder debris nor screws remain inside the product.

8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.

Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.

9 There should be no spark traces or similar marks on the power plug.

When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.

D 0 Safe environment should be secured during servicing.

When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.

2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.

3. Lubricants, Glues, and Replacement parts


Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
E

4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.

5. Shipping mode and Shipping screws


To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.

DEH-P40MP/XU/EW5
4
1 2 3 4
5 6 7 8

CONTENTS
SAFETY INFORMATION......................................................................................................................................2
1. SPECIFICATIONS .............................................................................................................................................6
2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................8 A
2.1 PACKING ....................................................................................................................................................8
2.2 EXTERIOR ...............................................................................................................................................10
2.3 CD MECHANISM MODULE .....................................................................................................................12
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................14
3.1 BLOCK DIAGRAM....................................................................................................................................14
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ..............................................................................16
3.3 KEYBOARD UNIT ....................................................................................................................................22
3.4 CD MECHANISM MODULE(GUIDE PAGE) .............................................................................................24
4. PCB CONNECTION DIAGRAM ......................................................................................................................32
4.1 TUNER AMP UNIT ...................................................................................................................................32
4.2 KEYBOARD UNIT ....................................................................................................................................36
4.3 CD CORE UNIT(S10.5COMP2) ...............................................................................................................38 B
5. ELECTRICAL PARTS LIST .............................................................................................................................40
6. ADJUSTMENT ................................................................................................................................................45
6.1 CD ADJUSTMENT ...................................................................................................................................45
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.....................................................47
6.3 ERROR MODE .........................................................................................................................................49
6.4 SYSTEM MICROCOMPUTER TEST PROGRAM ....................................................................................50
7. GENERAL INFORMATION .............................................................................................................................51
7.1 DIAGNOSIS..............................................................................................................................................51
7.1.1 DISASSEMBLY......................................................................................................................................51
7.1.2 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................54
7.2 PARTS ......................................................................................................................................................55
7.2.1 IC ...........................................................................................................................................................55 C
7.2.2 DISPLAY ................................................................................................................................................64
7.3 OPERATIONAL FLOW CHART ................................................................................................................65
8. OPERATIONS .................................................................................................................................................66

DEH-P40MP/XU/EW5
5 6 7 8
5
1 2 3 4

1. SPECIFICATIONS

DEH-P40MP/XU/EW5
6
1 2 3 4
5 6 7 8

DEH-P40MP/XU/EW5
5 6 7 8
7
1 2 3 4

2. EXPLODED VIEWS AND PARTS LIST


NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List.
• The > mark found on some component parts indicates the importance of the safety factor of the part.
A
Therefore, when replacing, be sure to use parts of identical designation.
• Screw adjacent to mark on the product are used for disassembly.
"
• For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions,apply as you think it appropriate.)
2.1 PACKING

20
B

16
DEH-P40MP/XU/EW5packing

19

2
C

3
4

5 1
18
D
17
6
13
15 14

14
7 10

8
12
E

9 11

DEH-P40MP/XU/EW5
8
1 2 3 4
5 6 7 8
PACKING SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDP1015 13 Polyethylene Bag CEG1160
2 Polyethylene Bag CEG-162 14 Handle CND3707
A
* 3 Battery CEX1065 15 Bush CNV3930
4 Case Assy CXB3520
5 Remote Control Assy CXC5719 16 Carton YHG5142
17 Contain Box YHL5142
* 6 Accessory Assy YEA5017 18 Protector YHP5008
7 Screw Assy CEA6002 19 Protector YHP5009
8 Screw CBA1650 20-1 Owner's Manual YRD5110
9 Screw CBA1994
* 10 Polyethylene Bag CEG-127 20-2 Owner's Manual YRD5111
20-3 Owner's Manual YRD5112
11 Screw CRZ50P090FTC 20-4 Installation Manual YRD5113 B
12 Screw TRZ50P080FTC * 20-5 Warranty Card CRY1157

Owner's Manual,Installation Manual


Part No. Language

YRD5110 English, Spanish

YRD5111 German, French

YRD5112 Italian, Dutch, Russian

YRD5113 English, Spanish, German, French, Italian, Dutch, Russian


C

DEH-P40MP/XU/EW5
5 6 7 8
9
1 2 3 4

2.2 EXTERIOR
39
31 37
75 34
A 38
41

40
15 42
43
33
44 42
57 44 A 36
76
42
35
B 44 32
51
53 64
B 60
53 73 44 74
51
49

59 63
67 48 65
58 66
50 61
62
47
45
46 68 52
12
C 55 7
16
54 56
C 5
3 18 14
1 1 18 71
1 30 2
29 17
70
1 18 28
70
72
23 B 22
17
19 20
21 26
D
24
10 A 25
11

27

8
13
E
C
B 4
9
4

6
4

A DEH-P40MP/XU/EW5
69

DEH-P40MP/XU/EW5
10
1 2 3 4
5 6 7 8
EXTERIOR SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 Screw BSZ26P060FTC 50 Button(TA/EJECT) YAC5077
2 Screw BSZ26P200FTC A
3 Screw BSZ30P060FTC 51 Button(UP/DOWN) YAC5079
4 Screw BSZ30P200FTC 52 Button(EJECT) YAC5080
5 Earth Plate CNC8915 53 Button(R/L) YAC5102
54 Spring YBH5003
6 Holder CND3598 55 Ring YNS5123
7 Cushion CNM8890
8 Remote Control Assy CXC5719 56 Ring YNS5124
9 Cover CNS7068 57 Cover YNS5185
10 CD Mechanism Module(S10.5) CXK5763 58 Lighting Conductor YNV5036
59 Lighting Conductor YNV5037
11 Cable YDE5025 60 Connector(CN1801) CKS4943 B
12 Case YNB5014
13 Insulator YNM5062 61 LCD(LCD1801) YAW5064
14 Heat Sink YNR5031 62 Holder YNC5016
15 Panel YNS5192 63 Sheet YNM5026
64 Cushion YNM5027
16 Tuner Amp Unit YWM5151 65 Connector YNV5040
17 Screw BPZ26P080FTC
18 Screw BSZ26P060FTC 66 Lighting Conductor YNV5041
> 19 Fuse(10 A) CEK1208 67 Button(FUNC/AUDIO) YXA5229
20 Pin Jack(CN351) CKB1051 68 Grille Unit YXA5248
69 Chassis Unit YXA5234 C
21 Plug(CN901) CKM1376 70 Transistor (Q702,Q911) 2SD2396
22 Connector(CN101) CKS3408
23 Connector(CN701) CKS3829 71 IC(IC921) NJM2388F84
24 Connector(CN804) CKS4944 72 IC(IC301) PAL007C
25 Antenna Jack(CN401) CKX1056 73 IC(IC1802) TSOP4840SB1
* 74 Label CRW1541
26 FM/AM Tuner Unit CWE1951 75 Cord Assy CDP1015
27 Holder CND1054
28 Holder XNC7030 76 Cap CKX-003
29 Jack(CN621) YKS5001
D
30 Holder YNC5041

31 Panel Unit YXA5154


32 Button(DETACH) CAC4836
33 Spring CBH1835
34 Spring CBH2208
35 Spring CBH2367

36 Bracket CNC6791
37 Holder CNC8042
38 Cover CNM6276 E
39 Arm CNV4692
40 Arm CNV4728

41 Arm CNV5576
42 Screw IMS20P030FTB
43 Detachable Assy YXA5220
44 Screw BPZ20P080FTB
45 Spring CBH2210

46 Knob(SOURCE, VOLUME) YAA5008


47 Button(1-6) YAC5074 F
48 Button(EQ, BAND/ESC) YAC5075
49 Button(ATT, DISP/SCRL) YAC5076

DEH-P40MP/XU/EW5
5 6 7 8
11
1 2 3 4

2.3 CD MECHANISM MODULE

DEH-P40MP/XU/EW5
12
1 2 3 4
5 6 7 8
CD MECHANISM MODULE SECTION PARTS LIST
Mark No. Description Part No. Mark No. Description Part No.
1 CD Core Unit(S10.5COMP2) CWX3514 50 Rack CNV8342
2 Connector(CN101) CKS4911 A
3 Connector(CN701) CKS4808 51 Roller CNV8343
4 Screw BMZ20P025FTC 52 Holder CNV8344
5 Screw BSZ20P040FTC 53 Arm CNV8345
54 Guide CNV8347
6 Screw(M2 x 3) CBA1511 55 Arm CNV8348
7 Screw(M2 x 4) CBA1835
8 Washer CBF1038 56 Arm CNV8349
9 ••••• 57 Arm CNV8350
10 Spring CBH2609 58 Clamper CNV8365
59 Arm CNV8386
11 Spring CBH2612 60 Guide CNV8396 B
12 Spring CBH2614
13 Spring CBH2616 61 Arm CNV8413
14 Spring CBH2617 62 Collar CNV8447
15 Spring CBH2620 63 Motor Unit(M2) CXC4026
64 Arm Unit CXC4027
16 Spring CBH2855 65 Chassis Unit CXC4028
17 Spring CBH2937
18 Spring CBH2735 66 Gear Unit CXC4029
19 Spring CBH2854 67 Frame Unit CXC4031
20 Spring CBH2642 68 Motor Unit(M1) CXC7134
69 Screw Unit CXC6359 C
21 Spring CBH2856 70 Screw JFZ20P020FTC
22 Spring CBH2857
23 Spring CBH2860 71 Screw JGZ17P022FTC
24 Spring CBH2861 72 Washer YE20FTC
25 Spring CBL1686 73 Pickup Unit(P10.5)(Service) CXX1942
74 Screw IMS26P030FTC
26 Arm CND1909
27 Frame CND2582
28 Bracket CND2583
29 Arm CND2584
D
30 Lever CND2585

31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201

36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211

41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV8189
45 Gear CNV7219

46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV8448
49 Arm CNV7805

DEH-P40MP/XU/EW5
5 6 7 8
13
1 2 3 4

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM


3.1 BLOCK DIAGRAM
A
A TUNER AMP UNIT
VDD5

TUNPDO
TUNPCK
TUNPDI

LDET
CE2

CE1
SL
7 6 13 5 10 9 8 11 14 18 19 20 21
FM/AM TUNER UNIT

NC

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
T

IC5 T
IC3 EEPROM

5.0V 5V 3.3V LD
T
OSC LPF C

B ANTENNA CN401
C
S
AM ANT FMRF
1
1 ATT
2
RDS_CK
IC2
2.5V RDS_HSLK
FM ANT IC1
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER RDS_LOCK
RF adj
ANT adj

RDS_DATA

T51 CF52

ELEC
AUDIOGND

IC4 SOU
OSCGND

VDD_3.3


RFGND

3.3V 3.3V 2.5V 2.5V TUNL


DGND

2
C IN2_L
VCC
NC

2 12 15 22 16 4 17
BUSL- 5
IN4−_
VDD_3.3V BUSL+ 4
IN4+_
VCC8
AUX-L 3
IN3_L
CDL 1
IN1_L
CN101

11 IN1−
7 IN1+
Q101
B14
8 B.UP
IP_BUS

Q102
40
ASENBO

1 30
TX
5 2 29
5 IC101 RX
1 6 HA12241FP 27
RX2
8 52
IPPW
D CN621
KEY2 94
2 KEYAD
KEY1 34
3 KEYD
AUX-GND 10,12
4 IC751 1
AUX-L 14 NJM2794V
5

C CD CORE UNIT(S10.5COMP2) SYSTEM CON


PICKUP UNIT RF-AMP, CD DECODER, IC601(2
(P10.5)(SERVICE) D MP3/WMA DECODER,
DIGITAL SERVO /
PEG28

VDD DATA PROCESSOR


LASER CN101 CN701 CN701
DIODE LD- 141
15 15 Q101 LD
MD 142
5 5 PD 55 LOUT LOUT
REFO LOUT 13 13
VREF 8 133
8 REFOUT
AC,BD,F,E
HOLOGRAM 50
UNIT XTAL
FOM FOM X201
3 3 CD 16.93MHz
FOP FOP /XTAL 52
E MONITOR
FOCUS ACT. 2 2 DRIVER
TOP
DIODE TRACKING ACT. 1 1 TOP
TOM TOM IC301
4 4 VDD
LD+ BA5839FP IC201 CD 3V REGULATOR
14 14 TD,FD
12
FOM
PE5547A Q102
11 VCC
VDD
9 9
3 IC702 1
VDD5
FOP SD,MD
14 NJM2885DL1-33
TOP
13
TOM /PUEN 39
SPINDLE
MOTOR M
16 22 5
SOP LOEJ 16 /RESET RESET 21
15 LOEJ /RESET 8 8
SOM CDRST
18 21 43
LOAD/ CARRIAGE LCOP CLCONT CLCONT
MOTOR M 17
LCOM CONT
9 41
CONT BRST,BRXEN,BSRQ BRST,BRXEN,BSRQ,BDATA,BSCK

BDATA,BSCK
Q702
VD VD
VD 1 1 B.UP
8
12EJ Q701
7 2 2
8EJ
6 5
DSCSNS
9
HOME 22
VCCONT
S904 S905 S901
12EJ 8EJ HOME
VD
F S903
DSCSNS 11
VDSENS

DEH-P40MP/XU/EW5
14
1 2 3 4
5 6 7 8

CN351
SWL 4
RESET
1 IC961 2
VDD5
Q351
S-80835CNMC-B8U

12
/RESET

TUNPDO 68 RCFL 6
TPDI

TUNPDI 86
TPDO
LDET Q353
75
LDET
TUNPCK 67 TPCK
VDD5V REGULATOR
CE1 66 Q911
TUNPCE1
CE2
SL
65 TUNPCE2 VDD5 B
97 SL Q912

Q401 SYSTEM CONTROLLER


RDS_CK 74
RCK IC601(1/2) 47
PEG287A DALMON

RDS_HSLK 83
RDS57K
BACKUP SENSE B.UP
CN901
Q402 19
/BSENS /BSENS B.UP 1 1
RDS_LOCK 81 BACK UP
RDSLOCK Q931
20 /ASENS ACC
/ASENS 3 3
RDS_DATA 82 RDSDT ACC
ACC SENSE

2 2
GND

B.UP
POWER AMP 20 6

ELECTRONIC VOLUME/ Vcc Vcc


SOURCE SELECTOR
6 14
TUNL 2 Front_L FLIN 23 FL−
IN2_L
12 IC301
FL−
21 FL+
10 10
FL−
C
Pre/SW_L FL+ 12 12
PAL007C 3 RL− FL+
7 12 RL− 9 9
BUSL- 5 Rear_L RLIN 5 RL+ RL−
IN4−_L RL+ 11 11
4 RL+
BUSL+ IN4+_L IC151
PML015B 22 25 BREM
AUX-L 3 MUTE STBY B.REM 6 6
IN3_L B.REM
4
CDL 1 TEL
IN1_L 8 8

MUTE
Q453 VCC8
VCK, VDT, VST

B.UP
TUN 3V REGULATOR SYS 8V REGULATOR

VDD_3.3V
3 IC401 1 2 IC921 1
B.UP
NJM2885DL1-33 NJM2388F84
40 4
ASENBO
53
MUTE
30 Q451
TX
SYSPW

29
RX
27 RR RR
RX2 48 SYSPW − +
52 SYSPW
IPPW BACK
UP
FR FR
− + D
TEL IN B.
94 Q951 FL FL
KEYAD REM − +
34
KEYD 38 RL RL
TELIN GND ACC
− +

SYSTEM CONTROLLER
IC601(2/2)
PEG287A

13
Xout
X601

Xin
15
B KEYBOARD UNIT

KEY MATRIX
S1801 S1802 S1803 S1804 S1805
CN804 CN1801 FUNC BAND 1 4 2 E
Q851
SWVDD
VDD5 3 8 SWVDD S1806 S1807 S1808 S1809 S1810
Q852 RIGHT LEFT 3 5 DOWN
7
SWVDD
S1811 S1812 S1813 S1814 S1815
18 DSENS DSENS UP EQ AUDIO TA DISP
/DSENS 10 1
D1804-D1822
21 Q841
CDRST S1816 S1817 S1818
ILMB+ ILM
B.UP 5 6 EJECT ATT 6
Q842
1
ILMPW
KDT0-3,KST0-4

S1827 SWVDD
92 SSENS SRC 4
B.UP SSENS 4 7 REM.CON.
3 ROT1 ROT1 1 3 IC1802 1
ROT1 6 5
4 ROT0 ROT0 2 TSOP4840SB1
ROT0 7 4
17
22
VCCONT VOLUME REM KEY DATA 22
/SOURCE XO
X1801
35 DPDT DPDT 18 23 5MHz
DPDT 8 3 DPDT
LCD DRIVER/
XI F
36 KYDT KYDT 20 KEY CONTROLLER
KYDT 9 2 KYDT
10 IC 1801
VLCD PD6340A LCD1801
56
VDD

DEH-P40MP/XU/EW5
5 6 7 8
15
1 2 3 4

3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)


Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
A

A-a A-b
Large size
SCH diagram
A-a
FM(10%) : -29.5 dB
AM(15%) : -26.0 dB
C CN701

CD(-20 dB) : -19.4 dB


A-a A-b Guide page FM/AM TUNER UNIT

A-a A-b Detailed page

15MHz
CSS1653
C

AUX IN(-20 dB) : -17.8 dB

IP-BUS(-20 dB) : -17.8 dB


E

B
CN1801

A
DEH-P40MP/XU/EW5
16
1 2 3 4
5 6 7 8

A-b A

INPUT FM : -33.1 dB
AM : -29.6 dB
CD : -22.4 dB A TUNER AMP UNIT
IP-BUS : -20.8 dB
AUX IN : -20.8 dB
OUTPUT FM : -12.0 dB
AM : -8.5 dB
CD : -8.3 dB
IP-BUS : -8.7 dB
AUX IN : -8.7 dB
FRONT
R CH

SUB WOOFER
R CH
FRONT
L CH
G B
SUB WOOFER
L CH

>

3A

3300/16
CEK1208
600µH 10A
>

RR RR
- +
BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +

FM : 13.98 dB
AM : 17.48 dB
CD : 17.7 dB
IP-BUS : 17.3 dB
AUX IN : 17.3 dB

NOTE :
The > mark found on some component parts indicates
Symbol indicates a resistor.
No differentiation is made between chip resistors and the importance of the safety factor of the part.
discrete resistors. Therefore, when replacing, be sure to use parts of
Symbol indicates a capacitor. identical designation.
No differentiation is made between chip capacitors and
discrete capacitors.
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
Ex. *Resistors
Code Practical value
123 12k ohms
103 10k ohms
*Capacitors
Code Practical value F
103 0.01uF
101/10 100uF/10V

A
DEH-P40MP/XU/EW5
5 6 7 8
17
F
E
B
A

D
C

18
A-a A-b

A-b
INPUT FM : -33.1 dB
AM : -29.6 dB TUNER AMP UNIT

1
1

CD : -22.4 dB A

1
IP-BUS : -20.8 dB
AUX IN : -20.8 dB
OUTPUT FM : -12.0 dB
AM : -8.5 dB
CD : -8.3 dB
IP-BUS : -8.7 dB
AUX IN : -8.7 dB
FRONT
R CH

SUB WOOFER
R CH
FRONT

2
2

L CH
G

SUB WOOFER
L CH

2
>

3A

DEH-P40MP/XU/EW5
3
3

3300/16

4
4

CEK1208
600µH 10A
>
600µH 10A
>
5

5
3
4
RR RR
- +
BACK FR FR
UP - +
B. FL FL

6
6

REM - +
GND ACC RL RL
- +

5
FM : 13.98 dB
AM : 17.48 dB
CD : 17.7 dB
IP-BUS : 17.3 dB
AUX IN : 17.3 dB

DEH-P40MP/XU/EW5
7
7

6
NOTE :
The > mark found on some component parts indicates
Symbol indicates a resistor.
No differentiation is made between chip resistors and the importance of the safety factor of the part.
discrete resistors. Therefore, when replacing, be sure to use parts of
Symbol indicates a capacitor. identical designation.
No differentiation is made between chip capacitors and
discrete capacitors.
For resistors and capacitors in the circuit diagrams, their resistance values or
capacitance values are expressed in codes:
Ex. *Resistors
Code Practical value
123 12k ohms
8

8
103 10k ohms
*Capacitors
Code Practical value
103 0.01uF
101/10 100uF/10V
A-a A-b

A-b
19
E
A

D
C

F
B
F
E
B
A

D
C

20
A-a A-b

FM(10%) : -29.5 dB

A-a
A-b
AM(15%) : -26.0 dB
C CN701

1
1

1
CD(-20 dB) : -19.4 dB

2
2

FM/AM TUNER UNIT

DEH-P40MP/XU/EW5
3
3

15MHz
CSS1653

4
4

AUX IN(-20 dB) : -17.8 dB


AUX IN(-20 dB) : -17.8 dB
5

5
3
4

6
6

IP-BUS(-20 dB) : -17.8 dB

DEH-P40MP/XU/EW5
7
7

B
CN1801
8

8
A-a A-b

A-a
A-b

21
E
A

D
C

F
B
1 2 3 4

3.3 KEYBOARD UNIT

D LCD DRIVER/
KEY CONTROLLER

B
DEH-P40MP/XU/EW5
22
1 2 3 4
5 6 7 8

B KEYBOARD UNIT
B

A
CN804

B
DEH-P40MP/XU/EW5
5 6 7 8
23
1 2 3 4

3.4 CD MECHANISM MODULE(GUIDE PAGE)

A
C-a

PICKUP UNIT(P10.5)(SERVICE)

F
%

T
F

T
F
F
T F F
F F
T T T
T T

C #

SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF

The underlined indicates the switch position.

M1 CXC7134
SPINDLE MOTOR
S

C
$
C

M2 CXC4026
LOADING/CARRIAGE MOTOR T S

9 7
F C

0 8 4

E 5

CD DRIVER

C
DEH-P40MP/XU/EW5
24
1 2 3 4
5 6 7 8

A
C-b
C CD CORE UNIT(S10.5COMP2)

!
B

SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

A
CN701

^ &

C
DEH-P40MP/XU/EW5
5 6 7 8
25
F
E
B
A

D
C

26
C-a C-b

C-b
1
1

C CD CORE UNIT(S10.5COMP2)

2
2

SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE

DEH-P40MP/XU/EW5
3
3

4
4
5 6 7 8

CN701
A

6
B

&
^
C

C-a C-b
D

2 3 C-b
DEH-P40MP/XU/EW5
5 6 7 8
27
F
E
B
A

D
C

28
C-a C-b

C-a
C-b

1
1

PICKUP UNIT(P10.5)(SERVICE)

2
2

F
%

DEH-P40MP/XU/EW5
T
F

3
3

T
F
F
T F F
F F
T T T
T T

4
4

SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH ON-OFF
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5

5
M1 CXC7134
SPINDLE MOTOR
2

C
$
C

M2 CXC4026
LOADING/CARRIAGE MOTOR T S

6
6

9 7
F C

0 8 4

DEH-P40MP/XU/EW5
2

7
7

CD DRIVER
3
8

8
C-a c-b

C-a
C-b

29
E
A

D
C

F
B
1 2 3 4

- Waveforms Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div
28SNS 5 V/div 5CLCONT 5 V/div 28SNS 5 V/div
312SNS 5 V/div 4LOEJ 5 V/div 312SNS 5 V/div
4LOEJ 5 V/div 6VD 10 V/div 4LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation

Ref.: Ref.: Ref.:


GND GND GND

B Mode: Mode: Mode:


Normal Normal Normal

7SIN 1 V/div 1 s/div 0FIN 200 mV/div 500 ms/div @TE 500 mV/div 200 ms/div
8CIN 500 mV/div !RFOK(MONI_2) 2 V/div #FE 500 mV/div
9TIN 1 V/div 7SIN 2 V/div

12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation

C Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


Normal Normal Normal

#FE 500 mV/div 20 ms/div $MDX 2 V/div 200 ms/div $MDX 2 V/div 5 μs/div
0FIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
@TE 500 mV/div
9TIN 500 mV/div
D CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


Normal Normal Normal

0FIN 500 mV/div 200 ms/div @TE 500 mV/div 2 ms/div %RFAGC 1 V/div 500 μs/div
E #FE 500 mV/div %RFAGC 500 mV/div @TE 500 mV/div
9TIN 500 mV/div

Focus Search waveform Track Open waveform 1 Track Jump waveform

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


TEST TEST TEST

DEH-P40MP/XU/EW5
30
1 2 3 4
5 6 7 8

%RFAGC 1 V/div 500 μs/div %RFAGC 1 V/div 500 μs/div %RFAGC 1 V/div 2 ms/div A
@TE 500 mV/div @TE 500 mV/div @TE 500 mV/div
9TIN 500 mV/div 9TIN 500 mV/div 9TIN 500 mV/div

4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform

Ref.: Ref.: Ref.:


REFO REFO REFO

Mode: Mode: Mode:


TEST TEST TEST
B

%RFAGC 1 V/div 200 ms/div ^LOUT 1 V/div 200 μs/div 1DSCSNS 5 V/div 500 ms/div
@TE 1 V/div &ROUT 1 V/div 28SNS 5 V/div
8CIN 1 V/div 312SNS 5 V/div
7SIN 2 V/div 4LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation

Ref.: Ref.: Ref.:


REFO AGND GND
C
Mode: Mode: Mode:
Normal Normal Normal

1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div %RFAGC 1 V/div 500 μs/div
5CLCONT 5 V/div 28SNS 5 V/div 9TIN 1 V/div
4LOEJ 5 V/div 312SNS 5 V/div @TE 1 V/div
4LOEJ 5 V/div 0FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 μm) during play

Ref.: Ref.: Ref.:


GND GND REFO

Mode: Mode: Mode:


Normal Normal Normal

DEH-P40MP/XU/EW5
5 6 7 8
31
1 2 3 4

4. PCB CONNECTION DIAGRAM


4.1 TUNER AMP UNIT
A

NOTE FOR PCB DIAGRAMS


1.The parts mounted on this PCB
include all necessary parts for
A TUNER AMP UNIT
several destination.
For further information for AUX
respective destinations, be sure
to check with the schematic dia-
WIRED REMOTE INPUT
gram.
2.Viewpoint of PCB diagrams CORD ASSY
Connector Capacitor
IP-BUS INPUT
B SIDE A

SIDE B
P.C.Board Chip Part

C
CN701

F
DSENS

A
DEH-P40MP/XU/EW5
32
1 2 3 4
5 6 7 8

SIDE A

FRONT OUTPUT REAR OUTPUT OR


SUBWOOFER OUTPUT

G G G G
4 3 2 1 B
ANTENNA

FM/AM TUNER UNIT D

B CN1801
F
FRONT

A
DEH-P40MP/XU/EW5
5 6 7 8
33
1 2 3 4

A TUNER AMP UNIT

>FU353 (B,131,131) Fuse 3 A CEK1286

B 1

TEST

A
DEH-P40MP/XU/EW5
34
1 2 3 4
5 6 7 8

SIDE B

PCL D

A
DEH-P40MP/XU/EW5
5 6 7 8
35
1 2 3 4

4.2 KEYBOARD UNIT

A
B KEYBOARD UNIT SIDE A
B KEYBOARD UNIT SIDE B

TA
EJECT

6
B

5
4
3

C
2
1

A
CN804
SOURCE/
VOLUME

E
BAND
DISPLAY

EQ

FUNCTION
AUDIO

ATT

B
DEH-P40MP/XU/EW5
36
1 2 3 4
5 6 7 8

DEH-P40MP/XU/EW5
5 6 7 8
37
1 2 3 4

4.3 CD CORE UNIT(S10.5COMP2)

C CD CORE UNIT(S10.5COMP2) SIDE A


A

A CN701 PICKUP UNIT(P10.5)(SERVICE)

E
M2
LOADING
/CARRIAGE
MOTOR

M1
SPINDLE
MOTOR

C
DEH-P40MP/XU/EW5
38
1 2 3 4
5 6 7 8

C CD CORE UNIT(S10.5COMP2) SIDE B


A

C
DEH-P40MP/XU/EW5
5 6 7 8
39
1 2 3 4

5. ELECTRICAL PARTS LIST


NOTE:
A • Parts whose parts numbers are omitted are subject to being not supplied.
• The part numbers shown below indicate chip components.
Chip Resistor
RS1/_S___J,RS1/__S___J
Chip Capacitor (except for CQS.....)
CKS....., CCS....., CSZS.....
• The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
• Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 911 (A,6,99) Transistor 2SD2396
Unit Number : YWM5151 Q 912 (B,18,68) Transistor UMD2N
Unit Name : Tuner Amp Unit
Q 931 (B,61,86) Transistor UMX1N
Unit Number : Q 951 (B,81,87) Transistor 2SA1037K
D 454 (A,109,108) Diode 1SS133
C
Unit Name : Keyboard Unit D 701 (A,19,49) Diode HZS7L(C3)
D 751 (B,114,65) Diode FTZ6R8E
Unit Number : CWX3514
D 752 (B,113,82) Diode FTZ6R8E
Unit Name : CD Core D 801 (B,32,17) Diode DAN202U
Unit(S10.5COMP2) D 802 (B,36,17) Diode DAP202U
D 803 (B,109,22) Diode DAN202U
D 804 (B,106,26) Diode DAP202U

A
Unit Number : YWM5151
D
D
D
805
806
901
(B,25,18) Diode
(B,25,22) Diode
(A,76,106) Diode
DAN202U
DAP202U
S5688G
D 902 (A,79,104) Diode S5688G
Unit Name : Tuner Amp Unit D 903 (A,67,94) Diode S5688G
D
MISCELLANEOUS D 904 (A,63,94) Diode S5688G
D 911 (A,19,80) Diode S5688G
IC 101 (B,60,59) IC HA12241FP D 912 (A,20,71) Diode HZS6L(B2)
IC 151 (B,134,81) IC PML015B D 931 (A,57,89) Diode HZS7L(C3)
IC 301 (A,93,131) IC PAL007C D 932 (A,53,85) Diode HZS7L(A1)
IC 401 (B,165,27) IC NJM2885DL1-33
IC 601 (B,85,56) IC PEG287A D 951 (B,77,91) Diode DAN202U
L 101 (A,53,67) Inductor LAU2R2K
IC 702 (B,39,67) IC NJM2885DL1-33 L 161 (A,112,87) Inductor LAU2R2K
IC 751 (B,114,76) IC NJM2794V L 401 (A,155,93) Inductor LAU1R0K
IC 921 (A,7,118) IC NJM2388F84 L 402 (B,159,97) Inductor LCTAW220J2520
E IC 961 (B,64,33) IC S-80835CNMC-B8U
Q 101 (B,38,93) Transistor 2SA1576A L 403 (A,156,52) Inductor LAU1R0K
L 602 (A,96,36) Inductor LAU2R2K
Q 102 (B,31,110) Transistor DTC114EUA L 852 (A,47,8) Inductor LAU2R2K
Q 351 (B,164,121) Transistor UMH3N L 901 (A,36,100) Choke Coil 600 µH CTH1280
Q 353 (B,135,122) Transistor UMH3N L 951 (A,73,93) Inductor LAU2R2K
Q 401 (B,157,37) Transistor UMH1N
Q 402 (B,157,43) Transistor UMH1N X 601 (A,73,37) Resonator 15.000 MHz CSS1653
>FU353 (B,131,131) Fuse 3 A CEK1286
Q 451 (B,121,110) Transistor DTC124EUA Z 401 (A,163,99) FM/AM Tuner Unit CWE1951
Q 453 (B,121,116) Transistor UMD2N AR401 (B,164,111) Surge Protector IMSA-6801-01Y901
Q 701 (B,25,49) Transistor UMD2N > Fuse 10 A CEK1208
Q 702 (A,6,65) Transistor 2SD2396
F Q 841 (B,125,24) Transistor 2SA1036K RESISTORS
Q 842 (B,120,26) Transistor DTC114EUA
R 101 (B,32,120) RS1/16S181J
Q 851 (B,36,11) Transistor 2SA1036K
R 102 (B,33,98) RS1/16S222J
Q 852 (B,36,7) Transistor DTC114EUA
DEH-P40MP/XU/EW5
40
1 2 3 4
5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 103 (B,25,127) RS1/16S181J R 604 (B,97,62) RS1/16S681J
R 104 (B,36,132) RS1/16S101J R 605 (B,153,59) RS1/16S681J
R 105 (B,33,133) RS1/16S101J R 606 (B,110,40) RS1/16S103J
R 607 (B,145,56) RS1/16S681J A
R 106 (B,30,119) RS1/16S223J
R 107 (B,26,123) RS1/16S223J R 610 (B,104,50) RS1/16S473J
R 108 (B,27,122) RS1/16S102J R 613 (B,98,75) RS1/16S104J
R 109 (B,28,119) RS1/16S102J R 615 (B,69,62) RS1/16S0R0J
R 110 (B,34,93) RS1/16S332J R 616 (B,36,48) RS1/16S473J
R 619 (B,112,51) RS1/16S0R0J
R 111 (B,33,105) RS1/16S562J
R 112 (A,66,65) RD1/4PU102J R 620 (B,93,65) RS1/16S0R0J
R 113 (B,68,56) RS1/16S472J R 621 (B,15,137) RS1/16S102J
R 114 (B,66,56) RS1/16S472J R 622 (B,13,135) RS1/16S102J
R 116 (B,31,133) RS1/16S470J R 701 (A,14,46) RD1/4PU271J
R 703 (B,47,50) RS1/16S472J
R 117 (B,30,133) RS1/16S150J B
R 118 (B,56,64) RS1/16S0R0J R 704 (B,48,35) RS1/16S104J
R 151 (B,98,77) RS1/16S102J R 705 (B,51,43) RS1/16S472J
R 152 (B,98,79) RS1/16S102J R 706 (B,52,43) RS1/16S104J
R 153 (B,98,81) RS1/16S102J R 707 (B,37,44) RS1/16S104J
R 708 (B,56,42) RS1/16S221J
R 180 (B,125,88) RS1/16S0R0J
R 301 (B,126,105) RS1/16S471J R 709 (A,56,36) RD1/4PU102J
R 303 (B,124,105) RS1/16S471J R 710 (B,49,43) RS1/16S221J
R 304 (B,139,105) RS1/16S471J R 711 (A,56,38) RD1/4PU221J
R 306 (B,142,104) RS1/16S471J R 712 (B,49,50) RS1/16S221J
R 713 (B,36,46) RS1/16S102J
R 309 (A,85,76) RD1/4PU153J
R 351 (B,149,110) RS1/16S821J R 714 (B,25,44) RS1/16S104J C
R 352 (B,156,117) RS1/16S0R0J R 753 (B,109,68) RS1/16S0R0J
R 355 (B,136,119) RS1/16S821J R 755 (B,107,82) RS1/16S0R0J
R 356 (B,135,101) RS1/16S821J R 757 (B,107,74) RS1/16S223J
R 759 (B,107,76) RS1/16S223J
R 358 (B,132,127) RS1/16S821J
R 359 (B,163,131) RS1/16S223J R 803 (B,29,17) RS1/16S473J
R 360 (B,160,130) RS1/16S223J R 804 (B,105,21) RS1/16S222J
R 363 (B,135,127) RS1/16S223J R 805 (B,102,19) RS1/16S222J
R 364 (B,137,127) RS1/16S223J R 806 (A,87,15) RD1/4PU222J
R 807 (B,82,13) RS1/16S222J
R 381 (B,136,127) RS1/16S0R0J
R 382 (B,139,124) RS1/16S0R0J R 808 (B,29,15) RS1/16S104J
R 384 (B,145,117) RS1/16S0R0J R 809 (B,52,10) RS1/16S222J D
R 393 (B,141,126) RS1/16S0R0J R 810 (B,29,13) RS1/16S103J
R 394 (B,144,126) RS1/16S0R0J R 811 (B,92,30) RS1/16S473J
R 813 (B,103,26) RS1/16S104J
R 401 (A,156,56) RD1/4PU681J
R 402 (B,157,79) RS1/16S681J R 814 (A,110,26) RD1/4PU102J
R 403 (B,157,80) RS1/16S681J R 815 (B,103,22) RS1/16S102J
R 404 (B,157,82) RS1/16S681J R 816 (B,129,20) RS1/16S1R0J
R 405 (B,157,83) RS1/16S681J R 822 (B,33,45) RS1/16S102J
R 823 (B,30,65) RS1/16S102J
R 406 (B,157,87) RS1/16S681J
R 407 (B,157,89) RS1/16S102J R 824 (B,110,44) RS1/16S102J
R 408 (B,142,43) RS1/16S223J R 825 (B,26,14) RS1/16S102J
E
R 409 (B,112,53) RS1/16S223J R 826 (B,121,20) RS1/16S0R0J
R 410 (B,143,46) RS1/16S223J R 841 (B,124,29) RS1/16S103J
R 842 (B,121,28) RS1/16S472J
R 411 (B,142,45) RS1/16S223J
R 413 (B,157,33) RS1/16S221J R 851 (B,31,9) RS1/16S153J
R 414 (A,135,38) RD1/4PU4R7J R 852 (B,33,7) RS1/16S472J
R 415 (B,157,39) RS1/16S221J R 853 (B,109,10) RS1/16S222J
R 416 (A,135,54) RD1/4PU4R7J R 854 (B,32,12) RS1/16S0R0J
R 421 (B,155,79) RS1/16S0R0J R 911 (B,18,64) RS1/16S223J

R 451 (B,122,107) RS1/16S103J R 912 (A,19,75) RD1/4PU152J


R 452 (B,122,118) RS1/16S221J R 922 (B,11,111) RS1/16S473J
R 453 (B,121,113) RS1/16S153J R 931 (B,60,54) RS1/16S104J F
R 454 (A,117,113) RD1/4PU102J R 932 (B,55,57) RS1/16S104J
R 602 (B,68,42) RS1/16S103J R 933 (B,61,88) RS1/16S104J

R 603 (B,98,83) RS1/16S103J R 934 (B,61,89) RS1/16S473J


DEH-P40MP/XU/EW5
5 6 7 8
41
1 2 3 4

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 935 (B,57,85) RS1/16S473J C 604 (B,94,42) CKSRYB105K10
R 936 (B,61,91) RS1/16S473J C 605 (A,97,40) CEJQ100M16
R 937 (B,62,116) RS1/16S473J C 606 (B,79,32) CKSRYB104K25
A R 938 (B,60,121) RS1/4SA102J C 607 (A,71,29) CEJQ100M16

R 951 (B,75,84) RS1/16S473J C 609 (B,146,48) CCSRCH470J50


R 952 (B,77,87) RS1/16S102J C 701 (B,23,44) CKSRYB473K25
R 953 (B,87,89) RS1/16S472J C 703 (A,30,27) CEJQ101M10
R 954 (B,87,91) RS1/16S472J C 704 (B,144,73) CKSRYB105K10
R 955 (A,69,102) RD1/4PU153J C 705 (B,126,74) CKSRYB105K10

R 961 (B,70,34) RS1/16S102J C 708 (A,39,73) CEJQ220M10


R 962 (B,62,37) RS1/16S822J C 709 (B,36,71) CKSRYB105K10
C 710 (B,47,66) CKSRYB474K10
CAPACITORS C 751 (B,112,79) CKSRYB104K16
C 753 (B,111,68) CKSRYB472K50
B
C 101 (B,28,133) CKSRYB104K25
C 104 (B,52,64) CKSRYB103K50 C 754 (B,107,73) CKSRYB105K10
C 151 (B,144,78) CKSRYB105K10 C 755 (B,108,83) CKSRYB472K50
C 152 (B,145,77) CKSRYB105K10 C 756 (B,109,74) CKSRYB105K10
C 153 (B,160,71) CKSRYB224K16 C 758 (B,109,78) CKSRYB105K10
C 760 (B,107,78) CKSRYB105K10
C 154 (B,120,70) CKSRYB105K10
C 155 (B,162,69) CKSRYB224K16 C 761 (A,119,63) CEJQ220M10
C 156 (B,123,78) CKSRYB105K10 C 762 (A,122,73) CEJQ100M16
C 157 (B,123,80) CKSRYB105K10 C 851 (B,40,8) CKSRYB104K25
C 158 (B,123,81) CKSRYB105K10 C 901 (B,54,115) CKSRYB104K50
C 911 (A,26,53) CEJQ470M10
C 159 (B,121,88) CKSRYB153K50
C C 912 (B,23,68) CKSRYB103K50
C 160 (A,116,90) CEJQ100M16
C 161 (B,135,95) CKSRYB153K50 C 913 (A,22,60) CEAT102M16
C 162 (A,115,99) CEJQ470M10 C 921 (B,16,101) CKSRYB103K50
C 163 (B,120,85) CKSRYB104K25 C 922 (A,17,98) CEJQ221M10
C 923 (A,15,114) CEJQ101M16
C 165 (A,131,93) CEJQ100M16
C 305 (B,128,109) CKSQYB474K16 C 924 (B,16,110) CKSRYB103K50
C 306 (B,137,109) CKSQYB474K16 C 961 (B,67,34) CKSRYB473K25
C 307 (B,131,109) CKSQYB474K16 C 962 (A,65,38) CEJQ100M16
C 308 (B,134,109) CKSQYB474K16

C
C
309
310
(B,125,132)
(B,128,130)
CKSQYB225K10
CKSQYB225K10
B
Unit Number :
D
C 311 (A,104,122) CEJQ100M16 Unit Name : Keyboard Unit
C 313 (A,51,118) 3 300 µF/16 V CCH1494
C 315 (B,129,113) CKSRYB474K10
MISCELLANEOUS
C 316 (B,136,113) CKSRYB474K10
C 317 (B,131,113) CKSRYB474K10 IC 1801 (B,31,115) IC PD6340A
C 318 (B,134,113) CKSRYB474K10 IC 1802 (A,24,31) IC TSOP4840SB1
C 351 (A,125,92) CEJQ2R2M50 D 1801 (B,38,95) Diode DAN202U
C 352 (A,139,92) CEJQ2R2M50 D 1802 (B,37,100) Diode DAP202U
D 1804 (A,26,164) LED CL-490S-WK-SD
C 355 (A,124,99) CEJQ2R2M50
C 356 (A,145,98) CEJQ2R2M50 D 1805 (A,10,7) LED SML-310VT
C 357 (B,163,129) CKSRYB222K50 D 1806 (A,38,10) LED SML-310VT
E D 1807 (A,17,14) LED SML-310VT
C 358 (B,159,130) CKSRYB222K50
C 401 (A,152,50) CEJQ470M6R3 D 1808 (A,17,24) LED SML-310VT
D 1809 (A,36,24) LED CL-190UB2-X
C 402 (B,154,49) CKSRYB103K50
C 403 (B,150,33) CKSRYB103K50 D 1810 (A,28,20) LED CL-190UB2-X
C 404 (B,153,26) CKSYB475K10 D 1811 (A,44,48) LED SML-310VT
C 405 (A,152,87) CEJQ101M10 D 1812 (A,30,35) LED SML-310VT
C 406 (B,167,92) CKSRYB104K25 D 1813 (A,17,49) LED SML-310VT
D 1814 (A,31,62) LED SML-310VT
C 407 (B,163,66) CKSRYB103K50
C 408 (A,157,29) CEJQ220M10 D 1815 (A,43,84) LED SML-310VT
C 412 (B,160,40) CKSRYB105K10 D 1816 (A,42,96) LED SML-310VT
C 451 (A,120,121) CEJQ330M10 D 1817 (A,42,109) LED SML-310VT
F
C 601 (B,73,41) CCSRCH180J50 D 1818 (A,41,121) LED SML-310VT
D 1819 (A,41,134) LED SML-310VT
C 602 (B,78,41) CCSRCH180J50
D 1820 (A,9,148) LED SML-310VT
DEH-P40MP/XU/EW5
42
1 2 3 4
5 6 7 8

Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
D 1821 (A,9,161) LED SML-310VT S 903 (B,19,58) Switch(DSCSNS) CSN1067
D 1822 (A,41,147) LED SML-310VT S 904 (B,38,67) Switch(12EJ) CSN1068
X 1801 (B,38,105) Ceramic Resonator 5.00 MHz CSS1547 S 905 (B,24,68) Switch(8EJ) CSN1068
S 1801 (A,43,9) Push Switch CSG1155 A
RESISTORS
S 1802 (A,36,28) Push Switch CSG1155
S 1803 (A,43,80) Push Switch CSG1155 R 101 (B,60,73) RS1/10SR2R4J
S 1804 (A,42,118) Push Switch CSG1155 R 102 (B,59,71) RS1/10SR2R4J
S 1805 (A,43,93) Push Switch CSG1155 R 103 (B,60,71) RS1/10SR2R7J
S 1806 (A,25,62) Push Switch CSG1155 R 104 (B,52,69) RS1/16SS222J
R 105 (B,41,57) RS1/16SS102J
S 1807 (A,35,35) Push Switch CSG1155
S 1808 (A,43,105) Push Switch CSG1155 R 107 (B,41,59) RS1/16SS105J
S 1809 (A,42,130) Push Switch CSG1155 R 202 (B,32,62) RS1/16SS473J
S 1810 (A,43,54) Push Switch CSG1155 R 203 (B,42,45) RS1/16S473J
S 1811 (A,17,44) Push Switch CSG1155 R 204 (A,25,61) RS1/16SS221J
B
S 1812 (A,28,24) Push Switch CSG1155 R 206 (B,26,53) RS1/16SS104J
S 1813 (A,7,8) Push Switch CSG1155 R 210 (B,13,32) RS1/16SS102J
S 1814 (A,10,158) Push Switch CSG1155 R 214 (B,36,34) RS1/16SS472J
S 1815 (A,21,24) Push Switch CSG1155 R 216 (B,47,49) RS1/16SS472J
S 1816 (A,10,150) Push Switch CSG1155 R 221 (B,36,32) RS1/16SS103J

S 1817 (A,20,14) Push Switch CSG1155 R 222 (B,35,32) RS1/16SS103J


S 1818 (A,41,143) Push Switch CSG1155 R 225 (A,49,49) RS1/16SS103J
S 1827 (A,30,49) Switch YSD5010 R 226 (A,49,50) RS1/16SS393J
LCD1801 (A,18,80) LCD YAW5064 R 227 (B,45,51) RS1/16SS562J
R 228 (B,42,53) RS1/16SS122J
RESISTORS
C
R 229 (B,44,53) RS1/16SS472J
R 1801 (B,37,91) RS1/16S222J R 230 (B,21,28) RS1/16SS0R0J
R 1802 (B,39,91) RS1/16S222J R 232 (B,43,51) RS1/16SS122J
R 1803 (B,27,158) RS1/4SA561J R 233 (B,29,52) RS1/16SS103J
R 1804 (B,23,21) RS1/4SA102J R 234 (B,30,61) RS1/16SS473J
R 1805 (B,28,21) RS1/4SA561J
R 235 (A,25,63) RS1/16SS473J
R 1806 (B,33,21) RS1/4SA821J R 239 (B,26,48) RS1/16SS473J
R 1807 (B,28,64) RS1/4SA821J R 240 (B,10,31) RS1/16SS473J
R 1808 (B,10,151) RS1/4SA821J R 241 (B,9,32) RS1/16SS103J
R 1809 (B,10,154) RS1/4SA821J
R 1810 (B,18,21) RS1/4SA102J R 244 (A,20,52) RS1/16SS473J
R 255 (A,27,63) RAB4CQ104J
D
R 1831 (B,37,37) RS1/16S472J R 307 (A,34,19) RS1/16SS183J
R 1832 (B,37,35) RS1/16S472J R 308 (A,38,20) RS1/16SS183J
R 1833 (B,34,28) RS1/16S2R2J R 309 (A,35,21) RS1/16SS183J
R 1835 (B,35,30) RS1/16S121J
R 310 (A,38,21) RS1/16SS183J
CAPACITORS R 601 (B,28,38) RS1/16SS0R0J
R 602 (B,27,41) RS1/16SS0R0J
C 1801 (B,35,32) CKSRYB474K10 R 606 (B,23,41) RS1/16SS0R0J
C 1802 (B,35,91) CKSRYB104K16 R 701 (B,16,35) RS1/16SS221J
C 1803 (A,36,21) CKSRYF104Z25
C 1804 (A,33,20) CKSRYF104Z25 R 702 (A,23,55) RS1/16SS221J
C 1812 (A,38,162) CKSRYF104Z25
CAPACITORS E

C
Unit Number : CWX3514
C
C
106
202
(B,56,69)
(A,27,57)
CKSQYB475K6R3
CKSSYB104K10
C 204 (A,24,63) CKSSYB103K16
Unit Name : CD Core C 205 (B,23,43) CKSQYB475K6R3
Unit(S10.5COMP2)
C 206 (A,22,39) CKSSYB104K10
C 207 (A,24,37) CKSRYB104K16
MISCELLANEOUS C 209 (B,33,40) CEVW220M6R3
C 210 (B,29,42) CKSSYB104K10
IC 201 (A,34,46) IC PE5547A C 211 (A,27,34) CKSSYB104K10
IC 301 (A,27,14) IC BA5839FP
Q 101 (B,56,72) Transistor 2SA1577 C 212 (B,29,32) CKSRYB104K16 F
Q 102 (B,47,57) Transistor 2SB1689 C 213 (A,44,37) CKSSYB104K10
C 214 (A,28,33) CKSSYB104K10
X 201 (A,23,35) Ceramic Resonator 16.934 MHz CSS1603 C 216 (A,50,51) CKSSYB332K50
S 901 (A,53,37) Switch(HOME) CSN1067
DEH-P40MP/XU/EW5
5 6 7 8
43
1 2 3 4

Circuit Symbol and No. Part No.


C 217 (A,46,51) CKSSYB104K10

C 218 (A,49,51) CKSSYB473K10


A C 219 (A,45,53) CKSSYB104K10
C 220 (A,46,53) CKSSYB182K50
C 221 (A,44,53) CKSSYB104K10
C 222 (B,43,53) CCSSCH560J50

C 223 (B,45,53) CCSSCH4R0C50


C 224 (A,43,55) CKSSYB104K10
C 226 (A,40,58) CCSSCH680J50
C 227 (A,40,60) CCSSCH470J50
C 228 (A,39,62) CKSSYB103K16

C 229 (B,49,59) CKSSYB104K10


C 236 (A,42,61) CKSSYB104K10
B C 239 (B,44,51) CCSSCH220J50
C 240 (A,35,61) CKSSYB104K10
C 250 (B,36,30) CKSSYB102K50

C 251 (B,33,29) CKSSYB102K50


C 303 (A,35,19) CKSSYB472K25
C 304 (A,34,21) CKSSYB223K16
C 307 (B,25,9) CKSRYB104K16
C 308 (B,10,27) CKSRYB105K10

C 703 (B,11,37) CCSSCH101J50


C 704 (B,8,36) CKSSYB102K50
C 711 (A,25,26) CKSSYB104K10
C
Miscellaneous Parts List
Pickup Unit(P10.5)(Service) CXX1942
M 1 Motor Unit(SPINDLE) CXC7134
M 2 Motor Unit(LOADING/CARRIAGE) CXC4026

DEH-P40MP/XU/EW5
44
1 2 3 4
5 6 7 8

6. ADJUSTMENT
6.1 CD ADJUSTMENT
A
1) Cautions on adjustments 2) Test mode
• In this product the single voltage (3.3 V) is used for the This mode is used to adjust the CD mechanism module.
regulator. The reference voltage is the REFO1 (1.65 V) • To enter the test mode.
instead of the GND. While pressing the 4 and 6 keys at the same time, reset.
If you should mistakenly short the REFO1 with the GND • To exit from the test mode.
during adjustment, accurate voltage will not be obtained, Turn off the ACC and back up.
and the servo’s misoperation will apply excessive shock
to the pickup. To avoid such problems: Notes:
a. Do not mix up the REFO1 with the GND when a. During ejection, do not press any other keys than the
connecting the (-) probe of measuring instruments. EJECT key until the loaded disc is ejected.
Especially on an oscilloscope, avoid connecting the (-) b. If you have pressed the (→) key or (←) key during focus
probe for CH1 to the GND. search, turn off the power immediately to protect the B
b. In many cases, measuring instruments have the same actuator from damage caused by the lens stuck.
potential as that for the (-) probe. Be sure to set the c. For the TR jump modes except 100TR, the track jump
measuring instruments to the floating state. operation will continue even if the key is released.
c. If you have mistakenly connected the REFO1 to the GND, d. For the CRG move and 100TR jump modes, the tracking
turn off the regulator or the power immediately. loop will be closed at the same time when the key is
released.
• Before mounting and removing filters or leads for e. When the power is turned off and on, the jump mode
adjustment, be sure to turn off the regulator. is reset to the single TR (91), the RF amp gain is set to 0 dB,
and the auto-adjustment values are reset to the default
• For stable circuit operation, keep the mechanism settings.
operating for about one minute or more after the
regulator is turned on. C

• In the test mode, any software protections will not


work. Avoid applying any mechanical or electrical
shock to the mechanism during adjustment.

• The RFI and RFO signals with a wide frequency range


are easy to oscillate. When observing the signals,
insert a resistor of 1k ohms in series.

• The load and eject operation is not guarantied with the


mechanism upside down. If the mechanism is blocked
due to mistaken eject operation, reset the product or D
turn off and on the ACC to restore it.

DEH-P40MP/XU/EW5
5 6 7 8
45
1 2 3 4

- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In

A Display

[CD] or [SOURCE]
Source On

TRK MIN SEC

[BAND] [3] [2] [4]


Power On Power On RF AMP *1 SPINDLE *9
(T.Offset is adjusted) (T.Offset is not adjusted) Gain switching Speed switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC
00 00 00 99 99 99 GG GG GG SP SP SP

[BAND] [3] [6] [1] [>] [<] [2]


[5]
Power Off Focus Close Focus Mode switching Tracking Servo CRG + CRG - Self-adjusting
B S curve check *2 Close *8 *8 switching *3 Gop Mode *10
Gop Mode switching
TRK MIN SEC TRK MIN SEC TRK MIN SEC 00 00 00 00 00 00 00 00 00 TRK MIN SEC
TRK MIN SEC
91 91 91 0X 0X 0X or 99 99 99 or 99 99 99 or 99 99 99 ?? ?? ??
OL OL OL

[BAND] [1] [6] [3] [>] [<] [2]


Power Off T.Close & AGC T.Close RF AGC / CRG + CRG - T.Balance adjustment /
Applicable servomechanism Applicable servomechanism RF AGC coefficient display T.BAL coefficient display
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X 8X 8X 8X TRK MIN SEC
?tr ?min ?sec ?tr ?min ?sec ?? ?? ?? or 9X 9X 9X or 9X 9X 9X ?? ?? ??

[BAND] [1] [3] [6] *5 [>] [<] [2]


Power Off F,T,RF AGC*7 F,T AGC / F.Bias CRG/TR jump CRG/TR Jump + CRG/TR Jump - Tracking Open
F.Bias display switching RF AGC value switching *4 *4
TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC TRK MIN SEC 8X 8X 8X
?? ?? ?? ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec ?tr ?min ?sec or 9X 9X 9X

C *6

[BAND] [2]
Power Off Tracking Open

TRK MIN SEC 8X 8X 8X


or 9X 9X 9X

*1) TYP → + 6 dB → + 12 dB Operation


TRK MIN SEC TRK
06MIN06SEC06 TRK
12MIN12SEC12 [Key] Test Mode
[BAND] Power On/Off
[>] CRG + / TR Jump +
*2) Focus Close → S Curve check setting → F EQ measurement setting (Direction of the external surface)
TRK
00MIN00SEC00 TRK
01MIN01SEC01 TRK
02MIN02SEC02 [<] CRG - / TR Jump -
(TRK99MIN99SEC99) (Direction of the internal surface)
D
[1] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the [2] RF Gain switching / Offset adjustment display /
order of the original display
T.Balance adjustment / T. Open
[3] F. Close,S Curve / Rough Servo and RF AGC /
*4) 1TR/4TR/10TR/32TR/100TR F,T,RF AGC
*5) Single → 4TR → 10TR → 32TR → 100TR → CRG Move [4] SPDL 1X/2X switching
9x(8x):91(81) 92(82) 93(83) 94(84) 95(85) 96(86) As for the double speed(2x), audio output cannot be
supported.
*6) Only at the time of CRG move, 100TR jump [5] Error Rate measurement
ON : ERR 30Counts Start
BER display data[%]
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
E [6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*8) CRG motor voltage = 2 [V]

*9) TYP (1X) → 2X → 1X *10) OFF(TYP) → FORCUS → TRACKING


TRK MIN SEC TRK
22MIN22SEC22 TRK
11MIN11SEC11 TRK MIN SEC TRK
70MIN70SEC70 TRK
71MIN71SEC71

• As for the double speed (2x), audio output cannot be supported

*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
F • In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.

DEH-P40MP/XU/EW5
46
1 2 3 4
5 6 7 8

6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT

• Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.

• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.

• Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.

• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFO1
• Disc • TCD-782
• Mode • TEST MODE

CD CORE UNIT(S10.5COMP2)
REFO1 C
E F L.P.F.

Xch Ych
E 100 kΩ
Oscilloscope
VREF 390 pF

F 100 kΩ

VREF 390 pF

L.P.F. D

• Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".

DEH-P40MP/XU/EW5
5 6 7 8
47
1 2 3 4

Grating waveform Ech → Xch 20 mV/div, AC


Fch → Ych 20 mV/div, AC
A

0° 30°

45° 60°

75° 90°

DEH-P40MP/XU/EW5
48
1 2 3 4
5 6 7 8

6.3 ERROR MODE


- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of A
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.

(1) Basic Indication Method


1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.

2) Head unit display examples


Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. B

8-digit display 6-digit display 4-digit display


ERROR–xx ERR–xx E–xx

(2) Error Code List


Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error → Failure on home switch or CRG move mechanism.
C
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
→ Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG → Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
→ Damages or stains on disc, or excessive vibrations on REWRITABLE. D

30 Electricity Search Time Out Failed to reach target address.


→ CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50 Mechanism CD On Mech Error Mechanical error during CD ON.
→ Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
→ Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). E
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.

DEH-P40MP/XU/EW5
5 6 7 8
49
1 2 3 4

6.4 SYSTEM MICROCOMPUTER TEST PROGRAM

A
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode
cancelled), shift the TESTIN IC601(Pin 88) terminal to H.
The clock signal is output from the PCL terminal IC601(Pin 39).
The frequency of the clock signal is 468 750 Hz that is one 32th of the fundamental frequency.
The clock signal should be 468 750 Hz(- 10 Hz, + 15 Hz).
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.

DEH-P40MP/XU/EW5
50
1 2 3 4
5 6 7 8

7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 DISASSEMBLY
A
- Removing the Case (not shown)

1. Remove the Case.

- Removing the CD Mechanism Module (Fig.1) CD Mechanism Module

1 Remove the four screws.

Disconnect the connector and then remove the


CD Mechanism Module. 1 B

- Removing the Grille Assy (Fig.1) 1

2 Release the two latchs and then


remove the Grille Assy.

2 1 2 C

Grille Assy

Fig.1

- Removing the Tuner Amp Unit (Fig.2)

D
1 Remove the screw.

2
2 2
2 Remove the three screws.

3 Straighten the tabs at four locations


indicated and then remove the Tuner
Amp Unit.

3
E
1

3
3 3

F
Tuner Amp Unit

Fig.2

DEH-P40MP/XU/EW5
5 6 7 8
51
1 2 3 4

- How to hold the Mechanism Unit


1. Hold the Upper and Lower Frames.
2. Do not hold the front portion of the Upper
A Frame, because it is not very solid.

Do not squeeze this area.

- Removing the Upper and Lower Frames


1. With a disc inserted and clamped in the a
B
mechanism, remove the two Springs (A), Upper Frame
the six Springs (B), and the four Screws. B
2. Turn the Upper Frame using the part "a" as
a pivot, and remove the Upper Frame.
C
3. While lifting the Carriage Mechanism,
B
remove it from the three Dampers.
Caution: When assembling, be sure to apply
some alcohol to the Dampers and assemble B
the mechanism in a clamped state.

B
B

A
Damper
D Damper
A
Carriage Mechanism Lower Frame

DEH-P40MP/XU/EW5
52
1 2 3 4
5 6 7 8

- How to remove the CD Core Unit


1. Apply Shorting Solder to the flexible cable of Shorting Solder
the Pickup, and disconnect it from the
connector. A
2. Unsolder the four leads, and loosen the
Screw.
3. Remove the CD Core Unit.
Caution: When assembling the CD Core Unit,
assemble it with the SW in a clamped state
so as not to damage it.

Screw

B
CD Core Unit

Solder

- How to remove the Pickup Unit


1. Make the system in the carriage mechanism mode, and have it clamped.
2. Remove the CD Core Unit and remove the leads from the Inner Holder.
3. Remove the Poly Washer, Change Arm, and Pickup Lock Arm.
4. While releasing from the hook of the Inner Holder, lift the end of the Feed Screw. C
Caution: When assembling, move the Planet Gear to the load/eject position before setting the Feed Screw in the Inner
Holder.
Assemble the sub unit side of the Pickup, taking the plate (Chassis) in-between. When treating the leads of the Load
Carriage Motor Assy, do not make them loose over the Feed Screw.

Poly Washer Change Arm

Pickup Lock Arm


Inner Holder
Feed Screw

Planet Gear
Pickup Rack

Chassis

Pickup

DEH-P40MP/XU/EW5
5 6 7 8
53
F
E
B
A

D
C

54
1
1

2
2

IP-BUS INPUT
AUX
ANTENNA FRONT WIRED REMOTE INPUT
OUTPUT
REAR OUTPUT OR
SUBWOOFER OUTPUT
7.1.2 CONNECTOR FUNCTION DESCRIPTION

1. BUS+
2. GND
3. GND

DEH-P40MP/XU/EW5
16 14 12 10 8 6 4 2 4. NC
15 13 11 9 7 5 3 1 5. BUS- 8 9 10 11
6. GND 5 6 7

3
3

7. BUS L+ 1 2 3 4
8. ASENB
1 B. UP 9 RL- 9. BUS R+
2 GND 10 FL- 10. BUS R-
3 ACC 11 RL+ 11. BUS L-
4 NC 12 FL+
5 NC 13 RR-
6 B. REM 14 FR-
7 NC 15 RR+
8 TEL 16 FR+

4
4
5 6 7 8

7.2 PARTS
7.2.1 IC

HA12241FP A

stb VCC +BUS -BUS


8 7 6 5

BIAS

+ DRIVER
OUTPUT
- (current)

+
RECEIVER
PAL007C OUTPUT
COM
-

1 2 3 4
S1 R out S2 GND

sw_vcc
Protector;
Over voltage
1

TAB Reference
amp_vcc

Stand-by
2

P-GND2 Circuit

+-
3

OUT2-
Offset Protector;
4

STBY Detection Thermal


-+
5

OUT2+
C
6

VCC
+-
7

OUT1-
Offset
8

P-GND1 Detection
-+
9

OUT1+
10

SVR
11

IN1
12 13

IN2
amp_vcc

Protector;
S-GND Short circuit
D
14

IN4
15

IN3
16

AC-GND
17

+-

OUT3+
18

Offset
P-GND3 Detection
19

-+

OUT3-
20 21

VCC
+-

OUT4+ E
22

Offset
MUTE Detection
23

-+

OUT4-
24 25

P-GND4

SWITCH
sw_vcc
stby

Protector;
Over current limit

Mute circuit

DEH-P40MP/XU/EW5
5 6 7 8
55
F
E
B
A

D
C

56
LM_out
DATA
CLK
STB
Vcc
Vref
GND
PML015B

1
1

Level Meter Digital Supply Vp


IN1_L
Block & Pref
IN2_L
Reference PGND
IN3_L
- Block Diagram

IN4+_L
Isolator
IN4-_L Gain Auto Primary
Adjuster Zero Pre/SW_L
IN4-_R Volume
Isolator

Input Selector
IN4+_R Anti- Secondary
IN3_R Radiation
Filter Volume
IN2_R
IN1_R Anti-Alias
Pre/SW_R

Phase inv.
Filter
Secondary
Front_L
Volume

LPF

2
2

FIE_L
Secondary

Volume FIE Rear_L


TRE MID BASS

Secondary
Anti- Front_R
LOUDNESS HPF Radiation Volume

Filter FIE_R

DEH-P40MP/XU/EW5
Secondary FIE Rear_R
Volume

3
3

Soft step Blocks ( M.S. M.S.S. )


Vref 9
Vcc 8
Rear_L 7
Front_L 6
IN4-_L 5
IN4+_L 4
IN3_L 3
IN2_L 2
IN1_L 1

Pref 14
Vp 13
Pre/SW_L 12
FIE_L 11
GND 10
- Pin Layout

4
4

20 CLK
21 STB

19 DATA

16 LMout
18 FIE_R
26 IN3_R
27 IN2_R
28 IN1_R

15 PGND
24 IN4-_R
25 IN4+_R

22 Rear_R
23 Front_R

17 Pre/SW_R
5 6 7 8

NJM2794V

V+
OUT1 1 14 IN1+ A

NC 2 13 NC
IN1-
OUT1
IN1+
GND 3 12 IN1-

VREF 4 Vref 11 NC

V+ 5 10 IN2-
IN2+
OUT2
IN2-
NC 6 9 NC
C

OUT2 7 GND 8 IN2+

DEH-P40MP/XU/EW5
5 6 7 8
57
1 2 3 4

- Pin Functions (PEG287A)


Pin No. Pin Name I/O Format Function and Operation
1 ILMPW O C Illumination power output
A 2 NC Not used
3,4 ROT1,0 I Rotary encoder pulse input 1, 0
5,6 NC Not used
7 SWVDD O C VDD for display microcomputer
8 BYTE I External data bus width change input
9 CNVSS I Processor mode change input
10,11 NC Not used
12 reset I Reset input
13 XOUT O Main clock output
14 VSS I GND
15 XIN I Main clock input
16 VCC I Power supply input(+)
B
17 nmi I C NMI input
18 dsens Detach sense input
19 bsens Backup sense input
20 asens ACC sense input
21 cd-reset O C CD mechanism RESET output
22 vdcont O C VD power supply output
23 brst O C P-BUS : Reset output
24 brxen I/O C P-BUS : Reception enable input/output
25 bsrq I P-BUS : Service request input
26 NC Not used
27 RX2 I IPBUS : Input 2
C 28 NC Not used
29 RX IPBUS : Input
30 TX N IPBUS : Output
31 BSO C PBUS : Output
32 BSI PBUS : Input
33 BSCK C PBUS : Clock output
34 KEYD I Wired remote control input
35 DPDT C Display microcomputer communication data output
36 KYDT Display microcomputer communication data input
37 NC Not used
38 TELIN I TEL mute input
39 PCL O C Output for clock adjustment
D 40 ASENBO O C IPBUS : Slave ACC sense output
41-46 NC Not used
47 DALMON O C For consumption current reduction output
48 SYSPW O C System power control output
49-51 NC Not used
52 IPPW O C IPBUS : Driver power supply control output
53 MUTE O C System mute output
54 VST O C E.VOL strobe output
55 VCK O C E.VOL clock output
56 VDT O C E.VOL data output
57 NC Not used
58 ROMDATA I/O C ROM correction data input/output
E ROM correction clock output
59 ROMCK O C
60 ROMCS O C ROM correction chip select output
61 NC Not used
62 VCC I Power supply input(+)
63 NC Not used
64 VSS I GND
65 ce@ O C TUNER : Chip enable output(EEPROM)

DEH-P40MP/XU/EW5
58
1 2 3 4
5 6 7 8

Pin No. Pin Name I/O Format Function and Operation


66 CE1 O C TUNER : Chip enable output(PLL)
67 TUNPCK O C TUNER : Clock output(PLL)
68 TUNPDI I TUNER : Data input(PLL) A
69-73 NC Not used
74 rck RDS : Clock interrupt
75 ldet RDS : PLL lock detection interrupt
76-80 NC Not used
81 rds-lock I C RDS : Lock signal input
82 RDS-DATA I C RDS : Data input
83 rds-hslk I C RDS57K input(connected to HSLK)
84 NC Not used
85 RECIVE O C For operation check of RDS circuit
86 TUNPDO O C TUNER : Data output(PLL)
87 NC Not used
B
88 TESTIN I Test program input
89-91 NC Not used
92 SSENS Source key
93 NC Not used
94 KEYAD Wired remote control AD input
95 NC Not used
96 AVSS I A/D converter GND(Connected to VSS)
97 SL Signal level input(Field intensity)
98 VREF I A/D converter reference voltage input
99 AVCC I A/D converter power supply input terminal(Connected to VCC)
100 NC Not used
C
PEG287A
Format Meaning
30

C CMOS
1

31 100 N Nch open drain

50 81

D
51

80

DEH-P40MP/XU/EW5
5 6 7 8
59
1 2 3 4

- Pin Functions(PD6340A)
Pin No. Pin Name I/O Function and Operation
1-5 SEG4-0 O LCD segment output
A 6-9 COM3-0 O LCD common output
10 VLCD LCD drive power supply
11-14 KST3-0 O Key strobe output
15,16 KDT0,1 I Key data input (analogue input)
17 REM I Remote control reception input
18 DPDT I Display data input
19 NC Not used
20 KYDT O Key data output
21 MODA GND
22 X0 Crystal oscillator connection pin
23 X1 Crystal oscillator connection pin
24 VSS GND
B
25,26 KDT2,3 I Key data input
27 NC Not used
28 KST4 O Key strobe output
29-32 NC Not used
33-55 SEG35-13 O LCD segment output
56 VDD Power supply
57-64 SEG12-5 O LCD segment output

PD6340A
1

16

C 64 17

49 32
48

33

PE5547A
Format Meaning
108

73

C CMOS
E 109 72 N Nch open drain

144 37
1

36

DEH-P40MP/XU/EW5
60
1 2 3 4
5 6 7 8

- Pin Functions (PE5547A)


Pin No. Pin Name I/O Format Function and Operation
1 ROMDATA I/O /C E2PROM : Data input/output
2 ROMCK O C E2PROM : Clock output A
3 ROMCS O C E2PROM : Chip select output
4 NC Not used
5 LOEJ O C LOAD/EJECT direction switching output
6 DSCSNS I Disc sense input
7 *sns I 8 cm disc detection input
8 !@sns I 12 cm disc detection input
9 home I HOME SW sense input
10 TEMP Temperature information sense input
11 VDSENS VD power supply short circuit/earth fault sense input
12 adena O C A/D reference voltage supply control output
13 ADC.VDD Power supply for A/D converter
B
14 ADC.GND Ground for A/D converter
15 FLMD0 I Flash writing control terminal
16 reset I Internal microcomputer reset terminal
17 PULLDOWN O C Pull-down
18 NC Not used
19 testin I Chip check, test program start-up input
20 NC Not used
21 BSI I N P-BUS : Serial data input
22 BSO O N P-BUS : Serial data output
23 bsck I/O N P-BUS : Serial clock input/output
24 FTxD O N Tx for flash rewriting
25 FRxD I Rx for flash rewriting C
26 BRXEN I/O /C P-BUS : Reception enable input/output
27 bsrq I/O /C P-BUS : Service request input
28 NC Not used
29 fmode I Flash self-rewriting mode start-up input
30 FLRQ O C Flash self-rewriting reset voltage control
31 ROM I Open(EMPH)
32-36 NC Not used
37 MCKRQ O N CLOCK request
38 LRCKOK O N LRCK reference enable
39 puen O C Pickup hologram power supply control output
40 CD3VON O C CD + 3.3 V power supply control output
41 CONT O C Servo driver power supply control output D
42 VDCONT O C VD power supply control output
43 CLCONT O C CRG/LOAD-EJECT switching control output
44 CDMUTE O C CD mute control output
45 TEST I Test terminal
46 brst I P-BUS : Communication reset input
47 REGS Capacitor connection for standby
48 C.VDD Power supply for internal microcomputer
49 C.GND Ground for internal microcomputer
50 XTAL I Connected to the crystal oscillator
51 X.GND Ground for the crystal oscillator
52 xtal O Connected to the crystal oscillator
Power supply for the crystal oscillator E
53 X.VDD
54 DA.VDD Power supply for DAC
55 LOUT O Output of audio for the left channel
56 DA.GND Ground for DAC
57 REGC Connected to the capacitor for band gap
58 DA.GND Ground for DAC
59 ROUT O Output of audio for the right channel

DEH-P40MP/XU/EW5
5 6 7 8
61
1 2 3 4

Pin No. Pin Name I/O Format Function and Operation


60 DA.VDD Power supply for DAC
61 D.GND Ground for digital circuits
A 62 D.VDD Power supply for digital circuits
63 REG16 Capacitor connection for 1.6 V regulator
64 LRCK O C 3-wire audio LR clock output
65 SCKO O C 3-wire audio serial I/F clock output
66 DOUT O C 3-wire audio serial I/F data output
67-69 SVMON0-2 I/O /C Servo monitor input/output 0-2
70 SVMON3 I/O /C Servo monitor input/output 3(Ext MCK IN)
71 C33M O C DRAM CLOCK
72 (rcs) O C DRAM CS
73 (CKE) O C DRAM CKE output
74 ras O C Output of DRAM RAS
75 cas)(LDQM) O C DRAM Lower CAS(LDQM) output
B
76 cas!(UDQM) O C DRAM Upper CAS(UDQM) output
77 we O C Output of DRAM WE
78 oe(cas) O C DRAM OE(CAS) output
79-94 RDB0-15 I/O /C Input/output of DRAM data 0-15
95 IO.GND Ground for I/O terminal
96 IO.VDD Power supply for I/O terminal
97-108 RA0-11 O C Output of DRAM address 0-11
109 FD O C Output of focus drive PWM
110 TD O C Output of tracking drive PWM
111 SD O C Output of thread drive PWM
112 MD O C Output of spindle drive PWM
C 113 EFM O Output of EFM signals
114 ASY I Asymmetry input
115 ATEST O Analog tests
116 A.VDD Power supply for the analog system
117 A.GND Ground for the analog system
118 RFI I Input of RF
119 AGCO O Output of RF
120 C3T Connection to the capacitor for detecting 3T
121 AGCI I Input of AGC
122 RFO O Output of RF(AGC)
123,124 EQ2,1 I Equalizer 2, 1
125 RF2- I Reversal input of RF2
D 126 RF- I Reversal input of RF
127 A.GND Ground for the analog system
128 A.VDD Power supply for the analog system
129 A I Input of A
130 B I Input of B
131 F I Input of F
132 E I Input of E
133 REFOUT O Output of reference voltage
134 FE- I Reversal input of FE
135 FEO O Output of FE
136 ADCIN I FE,TE A/D converter input
137 TE- I Reversal input of TE
E 138 TEO O Output of TE
139 TE2 O TE2
140 TEC I TEC
141 LD O Output of LD
142 PD I Input of PD
143 AD.VDD Power supply for servo ADC
144 AD.GND Ground for servo ADC

DEH-P40MP/XU/EW5
62
1 2 3 4
5 6 7 8

- FM/AM Tuner Unit


7 6 13 5 10 9 8 11 14 18 19 20 21

CE2

ROM_VDD

SL

DI
CK
CE1

LDET

DO

RDS_CK

RDS_DATA

RDS_LOCK

RDS_HSLK
NC
A

IC 3 EEPROM IC 5

5.0V 5V 3.3V

OSC LPF

AM ANT FMRF
1 ATT
Rch
24
IC 2
IC 1 2.5V
FM ANT
3 3.3V
ATT Lch
23
FMRF MIXER, IF AMP DET, FM MPX,
RDS DECODER B
RF adj
ANT adj

T51 CF52

AUDIOGND

IC 4
OSCGND

VDD_3.3

RFGND

3.3V 3.3V 2.5V 2.5V


DGND

VCC
NC

2 12 15 22 16 4 17

No. Symbol I/O Explain


1 AMANT I AM antenna input AM antenna input high impedance AMANT pin is connected with C
an all antenna by way of 4.7 μH. (LAU type inductor) A series circuit
including an inductor and a resistor is connected with RF ground for
the countermeasure against the hum of power transmission line.
2 RFGND RF ground Ground of antenna block
3 FMANT I FM antenna input Input of FM antenna 75 Ω Surge absorber(DSP-201M-S00B)is necessary.
4 VCC power supply The power supply for analog block. D.C 8.4 V ± 0.3 V
5 SL O signal level Output of FM/AM signals level
6 CE2 I chip enable-2 Chip enable for EEPROM ”Low” active
7 NC non connection Not used
8 CE1 I chip enable-1 Chip enable for AF•RF ”High” active
9 CK I clock Clock D
10 DI I data in Data input
11 LDET O lock detector “Low” active
12 OSCGND osc ground Ground of oscillator block
13 ROM_VDD power supply Power supply for EEPROM pin 13 is connected with a power supply of
micro computer.
14 DO O data out Data output
15 DGND digital ground Ground of digital block
16 NC non connection Not used
17 VDD_3.3 power supply The power supply for digital block. 3.3 V± 0.2 V
18 RDS_CK O RDS clock Output of RDS clock(2.5 V)
19 RDS_DATA O RDS data Output of RDS data(2.5 V)
20 RDS_LOCK O RDS lock Output unit “High” active(2.5 V) (RDS_LOCK turns over by the E
external transistor. “Low” active)
21 RDS_HSLK O RDS high speed Output unit “High” active(2.5 V)(RDS_HSLK turns over by the
lock external transistor. “Low” active)
22 AUDIOGND audio ground Ground of audio block
23 L ch O L channel output FM stereo “L-ch” signal output or AM audio output
24 R ch O R channel output FM stereo “R-ch” signal output or AM audio output

DEH-P40MP/XU/EW5
5 6 7 8
63
1 2 3 4
7.2.2 DISPLAY

- LCD(YAW5064)
A

E
SEGMENT

COMMON

DEH-P40MP/XU/EW5
64
1 2 3 4
5 6 7 8

7.3 OPERATIONAL FLOW CHART

A
Power ON

VCC = 5 V
Pin 16, 62

bsens
Pin 19
B

bsens = L (B.UP ON)

asens
Pin 20

asens = L (ACC ON)

dsens
Pin 18
C
dsens = L (DETACH ON)

ASENBO←H
Pin 40

Starts
communication
with Grille
microcomputer. 300 ms

SWVDD←H
Pin 7 300 ms D

In case of the above signal, the communication


with Grille microcomputer may fail.
Source keys
If the time interval is not 300 msec, the oscillator
operative
may be defective.

Source ON

SYSPW←H
Pin 48

Completes power-on operation.


(After that, proceed to each source operation)

DEH-P40MP/XU/EW5
5 6 7 8
65
1 2 3 4

8. OPERATIONS

DEH-P40MP/XU/EW5
66
1 2 3 4
5 6 7 8

E
(CBA1994)

DEH-P40MP/XU/EW5
5 6 7 8
67
1 2 3 4

- Connection Diagram

DEH-P40MP/XU/EW5
68
1 2 3 4
5 6 7 8

DEH-P40MP/XU/EW5
5 6 7 8
69
1 2 3 4

- Jigs List
Name Jig No. Remarks
A Test Disc TCD-782 Checking
g the g
grating
g
L.P.F. Checking
g the g
grating
g ((Two pieces)
p )

- Grease List
Name Grease No. Remarks
Grease GEM1024 CD Mechanism Module
B Grease GEM1045 CD Mechanism Module

Before shipping out the product, be sure to clean the


following portions by using the prescribed cleaning
tools:
C
Portions to be cleaned Cleaning
g tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning
g paper
p p : GED-008

DEH-P40MP/XU/EW5
70
1 2 3 4

You might also like