TS3704

Micropower quad CMOS voltage comparators

Features
■ Push-pull CMOS output (no external pull-up
resistor required)
N
■ Extremely low supply current: 9μa typ per DIP14
comparator (Plastic package)
■ Wide single supply range 2.7V to 16V or dual
supplies (±1.35V to ±8V)
■ Extremely low input bias current: 1pA typ
D
■ Extremely low input offset current: 1pA typ SO14
■ Input common-mode voltage range includes (Plastic micropackage)
GND
■ High input impedance: 1012Ω typ
■ Last response time: 2μs typ. for 5mV overdrive P
■ Pin-to-pin and functionally compatible with TSSOP14
bipolar LM339 (Thin shrink small outline package)

Description Pin connections

(Top view)
The TS3704 is a micropower CMOS quad voltage
comparator with extremely low consumption of
9μA typ / comparator (20 times less than bipolar Output 2 1 14 Output 3

LM339). The push-pull CMOS output stage allows Output 1 2 13 Output 4

power and space saving by eliminating the VCC + 3 12 V CC -

external pull-up resistor required by usual open- Inverting Input 1 4 - + 11 Non-inverting Input 4

collector output comparators. Non-inverting Input 1 5 + - 10 Inverting Input 4

Thus response times remain similar to the LM339. Inverting Input 2 6 - + 9 Non-inverting Input 3

Non-inverting Input 2 7 + - 8 Inverting Input 3

February 2007 Rev 3 1/11

www.st.com 11
Schematic diagram TS3704

1 Schematic diagram

Figure 1. Schematic diagram (for 1/4 TS3704)

VCC +

T 10
T1 T2 T9 T17

R1 T11 T12 T18 T21

Input - Input +

T3 T4
Output

T 13
T8

T19 T20

T5 T7 T14 T15 T16

T6

VCC -

2/11
TS3704 Absolute maximum ratings

2 Absolute maximum ratings

Table 1. Absolute maximum ratings

Symbol Parameter Value Unit

VCC+ Supply voltage (1) 18 V

Vid (2)
Differential input voltage ±18 V
(3)
Vi Input voltage 18 V
Vo Output voltage 18 V
Io Output current 20 mA
(4)
IF Forward current in ESD protection diodes on input 50 mA
(5)
Power dissipation
pd DIP14 1500 mW
SO14 830
TSSOP14 710
Tstg Storage temperature range -65 to +150 °C
HBM: human body model(6) 500 V
(7)
ESD MM: machine model 50 V
(8)
CDM: charged device model 1.5 kV
1. All voltage values, except differential voltage, are with respect to network ground terminal.
2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input and the output voltages must never exceed the magnitude of the positive and
negative supply voltages.
4. Guaranteed by design.
5. Pd is calculated with Tamb = +25°C, Tj = +150°C and
Rthja = 80°C/W for DIP14 package
Rthja = 150°C/W for SO14 package
Rthja = 175°C/W for TSSOP14 package
6. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a
1.5kΩ resistor between two pins of the device. This is done for all couples of connected pin combinations
while the other pins are floating.
7. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between
two pins of the device with no external series resistor (internal resistor < 5Ω). This is done for all couples of
connected pin combinations while the other pins are floating.
8. Charged device model: all pins and the package are charged together to the specified voltage and then
discharged directly to the ground through only one pin. This is done for all pins.

Table 2. Operating conditions

Symbol Parameter Value Unit

Supply voltage
VCC+ TS3704C, TS3704I 2.7 to 16 V
TS3704M 4 to 16
Vicm Common mode input voltage range 0 to VCC+ -1.5 V
Operating free-air temperature range
Toper TS3704C 0 to +70 °C
TS3704I -40 to +125
TS3704M -55 to +125

3/11
Electrical characteristics TS3704

3 Electrical characteristics

Table 3. VCC+ = 3V, VCC- = 0V, Tamb = 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit

Input offset voltage (1)

Vio Vic = 1.5V 5 mV
Tmin ≤ Tamb ≤ Tmax 6.5
Input offset current (2)
Iio Vic = 1.5V 1 pA
Tmin ≤ Tamb ≤ Tmax 300
Input bias current (2)
Iib Vic = 1.5V 1 pA
Tmin ≤ Tamb ≤ Tmax 600
Input common mode voltage range 0 VCC+-1.2
Vicm V
Tmin ≤ Tamb ≤ Tmax 0 VCC+ -1.5
Common-mode rejection ratio
CMR
Vic = Vicm min 80 dB
Supply voltage rejection ratio
SVR
VCC+ = 3V to 5V 75 dB
High level output voltage
VOH Vid = 1V, IOH = -4mA 2 2.4 V
Tmin ≤ Tamb ≤ Tmax 1.8
Low level output voltage
VOL Vid = -1V, IOL = 4mA 300 400 mV
Tmin ≤ Tamb ≤ Tmax 575
Supply current (each comparator)
ICC No load - Outputs low 7 20 μA
Tmin ≤ Tamb ≤ Tmax 25
Response time low to high
tPLH Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV 1.2 μs
TTL input 0.7
Response time high to low
tPHL Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV 2 μs
TTL input 0.15
1. The specified offset voltage is the maximum value required to drive the output up to 2.5V or down to 0.3V.
2. Maximum values include unavoidable inaccuracies of the industrial tests.

4/11
TS3704 Electrical characteristics

Table 4. VCC+ = 5V, VCC- = 0V, Tamb = 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Unit

Input offset voltage (1)

Vio Vic = 2.5V, Vcc+ = 5V to 10V 1.2 5 mV
Tmin ≤ Tamb ≤ Tmax 6.5
Input offset current (2)
Iio Vic = 2.5V 1 pA
Tmin ≤ Tamb ≤ Tmax 300
Input bias current (2)
Iib Vic = 2.5V 1 pA
Tmin ≤ Tamb ≤ Tmax 600
Input common mode voltage range 0 VCC+-1.2
Vicm V
Tmin ≤ Tamb ≤ Tmax 0 VCC+ -1.5
Common-mode rejection ratio
CMR
Vic = Vicm min 80 dB
Supply voltage rejection ratio
SVR
VCC+ = +5V to +10V 92 dB
High level output voltage
VOH Vid = 1V, IOH = -4mA 4.5 4.7 V
Tmin ≤ Tamb ≤ Tmax 4.3
Low level output voltage
VOL Vid = -1V, IOL = 4mA 200 300 mV
Tmin ≤ Tamb ≤ Tmax 375
Supply current (each comparator) 9 20
ICC μA
No load - Outputs low 25
Response time low to high
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV 1.2
Overdrive = 10mV 1 μs
tPLH
Overdrive = 20mV 0.9
Overdrive = 40mV 0.8
TTL input 0.7
Response time high to low
Vic = 0V, f = 10kHz, CL = 50pF, overdrive = 5mV 2
Overdrive = 10mV 1.5
tPHL μs
Overdrive = 20mV 0.9
Overdrive = 40mV 0.7
TTL input 0.15
Fall time
tf
f = 10kHz, CL = 50pF, overdrive 50mV 30 ns
1. The specified offset voltage is the maximum value required to drive the output up to 4.5V or down to 0.3V.
2. Maximum values include unavoidable inaccuracies of the industrial tests.

5/11
Package information TS3704

4 Package information

In order to meet environmental requirements, STMicroelectronics offers these devices in

ECOPACK® packages. These packages have a Lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.

6/11
TS3704 Package information

4.1 DIP14 package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

a1 0.51 0.020
B 1.39 1.65 0.055 0.065
b 0.5 0.020
b1 0.25 0.010
D 20 0.787
E 8.5 0.335
e 2.54 0.100
e3 15.24 0.600
F 7.1 0.280
I 5.1 0.201
L 3.3 0.130
Z 1.27 2.54 0.050 0.100

7/11
Package information TS3704

4.2 SO14 package mechanical data

Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.75 0.068
a1 0.1 0.2 0.003 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45° (typ.)
D 8.55 8.75 0.336 0.344
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 7.62 0.300
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.68 0.026
S 8° (max.)

8/11
TS3704 Package information

4.3 TSSOP14 package mechanical data

Figure 2. TSSOP14 package
Dimensions

Ref. Millimeters Inches

Min. Typ. Max. Min. Typ. Max.

A 1.2 0.047
A1 0.05 0.15 0.002 0.004 0.006
A2 0.8 1 1.05 0.031 0.039 0.041
b 0.19 0.30 0.007 0.012
c 0.09 0.20 0.004 0.0089
D 4.9 5 5.1 0.193 0.197 0.201
E 6.2 6.4 6.6 0.244 0.252 0.260
E1 4.3 4.4 4.48 0.169 0.173 0.176
e 0.65 BSC 0.0256 BSC
K 0° 8° 0° 8°
L 0.45 0.60 0.75 0.018 0.024 0.030

A A2
K L
A1 b e c E

E1

PIN 1 IDENTIFICATION
1

9/11
Ordering information TS3704

5 Ordering information

Table 5. Order codes

Temperature
Part number Package Packaging Marking
range

TS3704CN DIP14 Tube TS3704CN

0°C, +70°C Tube or
TS3704CD/CDT SO14 3704C
tape & reel
TS3704IN DIP14 Tube TS3704IN
Tube or
TS3704ID/IDT -40°C, +125°C SO14 3704I
tape & reel
TS3704IPT TSSOP14 Tape & reel 3704I
TS3704MN DIP14 Tube TS3704MN
Tube or tape &
TS3704MD/MDT -55°C, +125°C SO14 3704M
reel
TS3704MPT TSSOP14 Tape & reel 3704M

6 Revision history

Date Revision Changes

1-Oct- 2004 1 Initial release.

1 - PPAP references inserted in the datasheet.
1-Aug-2005 2
2 - ESD protection inserted in Table 1 on page 3.
PPAP references removed.
Updated footnotes related to ESD in Table 1 on page 3.
26-Feb-2007 3
Added Table 2 on page 3.
Order codes added to Table 5 on page 10.

10/11
TS3704

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.

The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2007 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

11/11