Penguard Tie Coat 100
Penguard Tie Coat 100
Penguard Tie Coat 100
The information herewith is given with the best of New Guard Coatings Group knowledge.
Rights are reserved to change and update the data without notice.
This information is not exhaustive and it is the user’s responsibility to ensure that this data sheet is the most current
by contacting their local New Guard Coatings Group branch prior to using the coating/product.
www.newguardcoatings.com
NORTH • SOUTH EAST • MIDLANDS • NORTH WEST • HULL • SCOTLAND
Technical Data Sheet
Product description
This is a two component, polyamide cured, high molecular weight epoxy coating. Specially designed as holding
primer, sealer and as a tie coat on top of inorganic zinc silicate primers, galvanized steel and thermally sprayed
zinc. To be used as primer in a complete system in atmospheric environments.
Typical use
Suitable for structural steel and piping exposed to highly corrosive environments. Recommended for offshore
environments, refineries, power plants, bridges, buildings and mining equipment.
Other
When used as part of an approved scheme, this material has the following certification:
- Low Flame Spread in accordance with EU Directive for Marine Equipment. Approved in accordance with parts 5
and 2 of Annex 1 of IMO 2010 FTP Code, or Parts 5 and 2 of Annex 1 of IMO FTPC when in compliance with
IMO 2010 FTP Code Ch. 8
Colours
red
Product data
Property Test/Standard Description
The provided data is typical for factory produced products, subject to slight variation depending on colour.
All data is valid for mixed paint.
Gloss description: According to Jotun Performance Coatings' definition.
Surface preparation
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any
contamination.
Surface preparation
Optimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is
achieved with recommended surface preparation.
Application
Application methods
The product can be applied by
Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17
For maximum overcoating intervals, refer to the Application Guide (AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.
Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.
Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.
Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.
Heat resistance
Temperature
Continuous Peak
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these
temperatures.
Product compatibility
Depending on the actual exposure of the coating system, various primers and topcoats can be used in
combination with this product. Some examples are shown below. Contact Jotun for specific system
recommendation.
Packaging (typical)
Volume Size of containers
(litres) (litres)
The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary
due to local regulations.
Storage
The product must be stored in accordance with national regulations. Keep the containers in a dry, cool, well
ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle
with care.
Shelf life at 23 °C
Penguard Tie Coat 100 Comp A 24 month(s)
Penguard Tie Coat 100 Comp B 48 month(s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf
life, thereafter the paint quality is subject to re-inspection.
Caution
This product is for professional use only. The applicators and operators shall be trained, experienced and have
the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun's technical
documentation. Applicators and operators shall use appropriate personal protection equipment when using this
product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit
the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing
the work.
Colour variation
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations
from batch to batch. Such products and epoxy based products used as a finish coat may chalk when exposed to
sunlight and weathering.
Colour and gloss retention on topcoats/finish coats may vary depending on type of colour, exposure
environment such as temperature, UV intensity etc., application quality and generic type of paint. Contact your
local Jotun office for further information.
Disclaimer
The information in this document is given to the best of Jotun's knowledge, based on laboratory testing and
practical experience. Jotun's products are considered as semi-finished goods and as such, products are often
used under conditions beyond Jotun's control. Jotun cannot guarantee anything but the quality of the product
itself. Minor product variations may be implemented in order to comply with local requirements. Jotun reserves
the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs
and specific application practices.
If there is any inconsistency between different language issues of this document, the English (United Kingdom)
version will prevail.