B NL - IMRO.0753.ovzonneveldkoppel-VG01 db9

Behoort bij besluit van burgemeester
en wethouders van Best

d.d.22 juli 2021
Ground Mount Photovoltaic Mounting System ZM 2V

Assembly Guide
All images are typical examples; please refer to project specific drawings.
1. General
The open area solar mounting frame ZM 2V, is to be used exclusively as a Photovoltaic
assembly frame and is projected individually on the local conditions.
This includes a static according the local conditions to determining the cross sections, as well
as a geotechnical certificate to regulate the pile driving deepness. It has to be rammed and
assembled after the given planning documents.
The design adheres to the following standards:

- DIN 1055-4 Wind load
- DIN 1055-5 Snow and Ice loads
- EN 1991-1-3 Snow load (Eurocode 1)
- EN 1991-1-4 Wind load (Eurocode 1)
Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Date: 12/2015; Technical modifications and mistakes reserved. page 1 of 27
Assembly Guide
2. Design and Planning

Before delivery we prepare for every system overview drawings, table division and bolt part
lists. These drawings and views show the dimensions, inclination, and position of each
component as well as the joining means.
By using slotted holes we designed a compact and variable system, allowing an

adjustable inclination with a range of 20° to 25°. The numbers of holes in the
posts counter inaccuracies of the driven post. This means every single assembly
frame can easily be adjusted to the required position.
2.1 Section View
2.2 Example Table Design

Assembly Guide

Assembly Guide
3. Detailed Views
Before starting assembly please read all safety guidelines. The PV mounting
frames are made of hot-dip-galvanized steel, stainless steel, and aluminium
components.
Tools:
You need the following tools
- ring spanner (wrench) 13mm, 19mm, 32mm
- Allen wrench (Allen key) 5 mm, 6 mm

Assembly Guide
4. Post Driving
The post-driving has to be done by a specialist company with suitable post driving rigs. They
need to create a piling plan according to the table layout. To this plan all V-Post must be
driven. Post length and foundation depth are given for each project.
Pre-treatment of the V-Post
We recommend coating the area between ground and air level of each post with an
additional protective coat. The additional protective coat should be painted before ramming
about 20cm below the earth surface line and up to 15cm above the earth surface. We
recommend as coating material PHARMOL: 2K Acrylan-ESL
Treatment of the V-Post After Driving

The top of the V profile has to be painted after ramming, to protect against surface damage
due to the pile driving. It has to be painted approx. 3cm from the top of the profile with the
coating material PHARMOL Acrylan-ESL.
In the case of aggressive soils being found in the geological survey the posts can be powder
coated, albeit at an additional cost.

Assembly Guide
5. General Overview
Pos. Pieces Number Description

1 1 15030042a Main Tube Short 850mm, 60x60x3
2 1 15030043a Main Tube Long 1480mm, 60x60x3
3 1 15030045a Inclined Tube 4136mm 80x40x3
4 1 15000109a V Post 1800mm
5 1 15000110a V Post 2100 mm
6 1 15030047a Brace 1075mm, 30x30x3
7 1 4012312060 Hex Bolt HDG DIN 931, M 12 x 60
8 1 4012734912 Washer HDG DIN 7349 M12 13x30x6
9 7 4012734912 Hex Nut HDG M12 DIN 934-8
11 9 4012312090 Washer HDG DIN 125 13x24x2,5
12 4 M12 DIN 440 Washer HDG

Assembly Guide
⑬⑭⑮⑯⑰

13 5 15000103a Clamp for c-rail
14 5 4010408031 Hex Bolt HDG DIN 933, M8x30
15 5 4010012508 Washer VA DIN 125, M8
16 5 2500101865 Threaded plate M8, VA stainless
17 15000117a C-rail 90x60x20, 9908mm

Assembly Guide
6. Post to Main Tube Assembly
The vertical main tubes (Pos. 1 and Pos. 2) need to be bolted to V Post (Pos. 4 and Pos. 5).
Fasteners: Pos. 9, Pos. 10, Pos. 11

4 1 15000109a V Post 1800mm
5 1 15000110a V Post 2100 mm
9 7 4012093412 Hex Nut HDG M12 DIN 934-8
11 9 4012012512 Washer HDG DIN 125 13x24x2,5

Assembly Guide
7. Assembly Supporting Tube
The inclined tube (Pos. 3) needs to be inserted into the recesses of the main tubes (Pos. 1
and 2). Fasteners: (Pos. 13, Pos. 12, Pos 10).
Please check the angle of the inclined tube.

9 1 4012734912 Hex Nut HDG M12 DIN 934-8
12 9 DIN 440 Washer HDG

Assembly Guide
8. Brace Assembly
Assemble brace (Pos. 6) to inclined tube (Pos.3) and to main tube (Pos. 1 and Pos.2). Insert
the brace into the dedicated recesses and fasten with fixings to main tube. Fasteners:
Pos. 7; Pos. 8; Pos. 9, Pos. 11

6 1 15030047a Brace 1075mm, 30x30x3
8 1 4012734912 Washer HDG DIN 7349 M12 13x30x6
9 7 4012093412 Hex Nut HDG M12 DIN 934-8
11 9 4012012512 Washer HDG DIN 125 13x24x2,5

Assembly Guide
Pos. 9; Pos. 10; Pos. 11

4 1 15000109a V Post 1800mm
5 1 15000110a V Post 2100 mm
9 1 4012734912 Hex Nut HDG M12 DIN 934-8
11 6 4012312090 Washer HDG DIN 125 13x24x2,5
Fine adjustment of support frame, check angle of the inclined tube and tighten all
fixings.
Please adhere to the following torques:
- M8 (A2-70 / A4-70): 12-15 Nm (C-Rail to Inclined Tube)
- M8 (A2-70 / A4-70): 20 Nm (C-rail connector)
- M12 (8.8): 65 Nm Braces
M12 (8.8): 40 Nm Connection V-post to main tube

Assembly Guide
9. Assembly panel supporting rail (C-rail)
Preassembly of the rail clamp (Pos 13, 14, 15, 16) (pre-assembly possible) and insert into
the keyholes, on the inclined tube (No. 3).
Then mount the rails on, insert into the preassembled clamp, adjust by using the provided
assembly jig and observe the cantilever (individually according to the assembly table layout).
Note for Panel Assembly in Portrait Mode:

Alignment of C-rails must be checked to ensure the rails and the positions of the slotted hole
are square to each other (see section 9.2)
Finally tighten the screws.
The panel support rails (C-rail)

need to be painted at the cut edges
with protective zinc coating.
Depending on row and table layout,
C-rails need to be cut to length on site
and protective zinc coating applied to the cut edges.
Assembly C-rail connector:

Please assemble the C-rail connector as illustrated with the surface face down.
Fastener:
- 6 x M8 x 20
- 6 x M8 screw nut
- 12 x M8 washer DIN 125
CAUTION: Please tighten the 2 bolts in the bottom ① of the rail before fastening the
4 bolts ② at the back of the rail.

Assembly Guide
9.1. Connection of C-Rails
When connecting the C-Rail with 6 bolts (see section 9) to each other please make sure that
the rails are square to each other and that the pitch (dimension X) between the key holes is
repeated over the connection points.
9.2. Squaring of the Rail Joints

When mounting the modules in portrait mode the rail joint of the superimposed C-rails must
always be aligned square to the keyhole.
For rows where modules are installed 50m or more, without a 20cm gap between the
strings, we provide a jig to align the rails to each other.
As you can see in the images, the distance from keyhole to keyhole is critical. The jig needs
to be set to this distance and this distance needs to be transferred rail to rail across the rail
joint.

Assembly Guide

Assembly Guide
10. Panel assembly

- by direct screw connection in the panel frame
Each panel will be screwed with suitable joining means (individually according the panel
type) directly by the panel frame and slots on the C- panel supporting rail (Pos. 2)
- There are different ways of fixing the panel to the frame, these options are
shown on the next page(s)
General note:
The distance between the modules is 19mm. Should the fastening of the panels with the
clamps in the keyholes become impossible due to uneven terrain or due to tolerances
occurring in the rail lengths and module dimensions, the following mounting solutions should
be considered:
- Alignment of the rails to each other - see point 9.2
- Use of 13mm wide panel clamps
- Use of 22mm wide panel clamps
- Use of two end clamps in the same keyhole
- Use of two end clamps in the same keyhole Module mounting with latch
bracket (see section 10 - Panel Assembly with Fixing Bracket)
Caution: The gap between side of the clamp and the side of the panels should not
exceed 2mm on each side.
All stainless steel fittings need to be lubricated to guarantee an easy installation.
The fitting instructions and safety guidelines from the panel manufacturer must
be adhered to.

Assembly Guide
Assembly aluminium panel clamp:

① Hexagon socket screw M8x45 VA stainless steel / (or M8x35, M8x40, M8x50)
② Schorr-U-Washer M8
③ Aluminium-panel clamp
④ Threaded plate M8, stainless steel
Please note the clamping torque. Tighten screw only with a cordless screwdriver
or by hand. Please do not use impact wrench.

Assembly Guide
Assembly aluminium panel-termination fitting:

③ Aluminium panel-middle clamp
④ Threaded plate M8, stainless steel

Assembly Guide
Assembly Aluminium Panel Clamp with Spacer H50:

① Aluminium panel-middle clamp
② Socket head hex screw M8x45 VA stainless steel
③ Schorr-U-Washer M8
④ Plastic spacer with nut M8 H50
Assembly Aluminium Panel Clamp with Spacer H40:
① Aluminium panel-middle clamp
② Socket head hex screw M8x35 VA stainless steel
③ Schorr-U-Washer M8
④ Plastic spacer with nut M8 H40

Assembly Guide
Panel mountings with counter bracket:

③ Aluminium panel-middle clamp
④ Counter bracket hdg
⑤ Self-locking-nut

Assembly Guide
Assembly clamp for C-rails:
③ Clamp for C-rails

⑦ Hexagon screw M8x50 VA stainless steel (DIN 931)
⑥ U-washer M8, 8,4x16x1,6, VA stainless steel (DIN 125)
⑧ Threaded plate M8, stainless steel

Assembly Guide
11. Anti-theft protection device
We don’t recommend fastening balls into the hexagon bolts for the anti-theft protection
device. It may cause damage to the panels.
Possible solution for anti-theft protection
- Glue panel clamps with PATTEX™ special glue (1 component heavy duty glue with
Silvan Polymer
12. Grounding
For grounding we recommend a hot dip galvanised grounding cable to EN ISO 1461.

Assembly Guide
13. Wind Brace
If a wind brace is required to stiffen up the construction the following assembly notes should
be adhered to.
The bolts at the main tubes need to be inserted with the threads opposing each other. The
chain needs to fixed to the main tubes next to each other (north end) so the cross. Fix the
ring nut to the existing hex bolts, without the M12 nut. Please fix one end of the chain with
the rod strainer to the ring nut, use a shackle on the other end and tighten the chain.
The wind bracing needs to be checked for tension about two weeks after installation.
If necessary adjust the turnbuckle by hand. Please do not over tighten the chain! For
maintenance, please check in regular intervals the tension of the chain. (Annually)
The wind brace cannot be fitted in sections where the rails are joined together.
Fastener:
- 4020000018 Steel chain
2 2 2500102508 !!! Text nicht vorhanden !!!
4 2 2500102509 !!! Text nicht vorhanden !!!
2 2 4012412035 Hex Bolt HDG DIN 933, M12x35
2 2 4012093412 Hex Nut HDG M12 DIN 934-8
2 6 4012012512 Washer HDG DIN 125, M12, 13x24x2,5

Assembly Guide

Assembly Guide
14. Inverter/Junction Box Brackets

C-rails are clamped onto two main tubes. C-rails need to be cut to length on site and the
ends must be coated with a zinc protective layer.
Onto these rails you can fix inverters/junction boxes etc. Please respect the manufacturer’s
instruction and the overall weight.
Example
The clamps can be pre-assembled.

Assembly Guide
Position the plates and nuts on the

main tube and into the c-rail as
required and clamp down

1 m 2500101060 C-rail HDG 75x55
2 1 4001000424 Small Plate
3 2 2500101940 Large plate M12
4 2 4012012512 Washer HDG DIN 125, M12, 13x24x2,5
5 2 4012312120 Hex bolt HDG DIN 931, M12x120
6 2 4012692312 Serrated Nut HDG DIN 6923, M12

Assembly Guide
15. Safety Guidelines
We recommend reading carefully the following information, because they are very important
for a correct installation of the system. Please follow them and get informed about the health
and safety regulations of other site components.
- Please observe all notes in the operating instructions for all works on the PV solar
plant. Assembly, repairs and maintenance has to be carried out by certified and
qualified personal.
- The valid regulations and safety guidelines need to be followed.
Some regulations need to be respected.
- BGV A 1 – General regulations
- BGV A 2 – Electrical plants and Equipment
- BGV C 22 – Construction work
- PPE and health and safety regulations are to be adhered to according to the local
regulations and laws.
DIN / EN Standards need to be respected.
- DIN 18299 – General regulations for construction work of every kind.
- DIN 18360 – Metal construction work, locksmith
Conservation / Environmental
- The whole system is completely recyclable, as it is made of high quality, reusable
components.
Maintenance regulations
All bolted connections on the mounting system must be checked at least once a year.
-
This has to be checked in regular intervals.
- All rod strainers have to be checked at least once a year. This has to be checked in
regular intervals.

Assembly Guide
Product liability (-exclusion)
- The assembly company is responsible for the correct execution for the assembly.
- The Zimmermann PV Stahlbau GmbH & Co. KG is not liable for any damages caused
from disregard of the assembly instructions and the safety guidelines, as well as by
not material-appropriate use of our products.
- Construction in a proximity of less the 2km to the sea need to be request separately,
as additional protections against corrosion are necessary.
-
Our instructions, our project-related plan documents and the general approved
standards and principles of the system are valid for the assembly and use of the
products delivered by us. The assembly is to be performed in general by specialists.
Part of our product is the technical documentation. All general Terms and
Conditions apply (retrievable at www.pv-stahlbau.de/en/).


B NL - IMRO.0753.ovzonneveldkoppel-VG01 db9

Uploaded by

Copyright:

Available Formats

B NL - IMRO.0753.ovzonneveldkoppel-VG01 db9

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

B NL - IMRO.0753.ovzonneveldkoppel-VG01 db9

Uploaded by

Copyright:

Available Formats

Behoort bij besluit van burgemeester

en wethouders van Best

Ground Mount Photovoltaic Mounting System ZM 2V

The design adheres to the following standards:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

2. Design and Planning

By using slotted holes we designed a compact and variable system, allowing an

2.1 Section View

2.2 Example Table Design

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Pre-treatment of the V-Post

Treatment of the V-Post After Driving

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Pos. Pieces Number Description

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Pos. Pieces Number Description

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

6. Post to Main Tube Assembly

Fasteners: Pos. 9, Pos. 10, Pos. 11

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

7. Assembly Supporting Tube

Please check the angle of the inclined tube.

Pos. Pieces Number Description

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Pos. 7; Pos. 8; Pos. 9, Pos. 11

Pos. Pieces Number Description

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Pos. 9; Pos. 10; Pos. 11

Pos. Pieces Number Description

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

9. Assembly panel supporting rail (C-rail)

Note for Panel Assembly in Portrait Mode:

Finally tighten the screws.

The panel support rails (C-rail)

Assembly C-rail connector:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

9.1. Connection of C-Rails

9.2. Squaring of the Rail Joints

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

10. Panel assembly

All stainless steel fittings need to be lubricated to guarantee an easy installation.

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Assembly aluminium panel clamp:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Assembly aluminium panel-termination fitting:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Assembly Aluminium Panel Clamp with Spacer H50:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Panel mountings with counter bracket:

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

Assembly clamp for C-rails:

③ Clamp for C-rails

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG

11. Anti-theft protection device

Possible solution for anti-theft protection

Production and Distribution: Zimmermann PV-Stahlbau GmbH Co. KG