PI8000 Manual MV110716E

Foreword
Thank you very much for purchasing PI8000,PI8100 Family Frequency Inverters.This family
is designed based on the experience of POWTRAN Company in the professional manufacture and
sale of the products, and suitable for general-purpose machine, fan/pump drive, medium frequency
drive and heavy load machine.
This product adopts the advanced sensorless vector control technology, combined with China
local frequency invenrter application features to achieve high-performance V/F control (dead-time
compensation + auto-torque upgrade + Slip Compensation) and high-performance non-sense vector
control, and high-performance speed sensorless vector control.
This product adopts the advanced sensorless vector control technology, combined with the
application of inverter technology in China features to achieve high-performance V/F control
(dead-time compensation + auto-torque upgrade + Slip Compensation) and high-performance
non-sense vector control, and high-performance speed sensorless vector control.
This Users Manual includes PI8000/PI8100, the general purpose control and special purpose
control . The general purpose control ha F, G, M and H; The special purpose control has S, T and
Z:
F: FLOW LOAD
G: GENERAL LOAD
M: MEIDDLE LOAD
H: HEAVY LOAD.
S: TEXDRIVE.
T: WINDLASS.
Z: JETDRIVE.
Please contact the local dealers or directly contact our company.
Please keep this users manual in good condition,for it will be helpful to the repair,maintenance,
and applications in the future.
For information about other product, please visit our website: http://www.powtran.com.

CONTENTS
Section I. Inspection & Safety Precautions ....................................... 1
Section II. Installation & Standby Circuit .......................................... 3
Section III. Operating Keyboard ....................................................... 13
Section IV. Test Running ................................................................... 21
Section V Parameter Function Table ............................................... 24
5-1. Functional parameter list .................................................................... 24
5-2. Functional parameter specification ..................................................... 54
Section VI. Fault Diagnosis & Solutions ......................................... 130
Section VII Standard Specifications ................................................ 132
Section VIII. Maintenance ................................................................. 147
Section IX. Options ......................................................................... 149
Section X Quality Assurance ......................................................... 153
Appendix I. RS485 Communication Protocol .................................. 154
Appendix II Instruction of the Proportional Linkage Function ........ 169
Appendix III. RS485 PG Card Instruction .......................................... 172
Appendix IV Converter Water Supply Controller Instruction ............ 174

1

S
e
c
t
i
o
n

I

Section I. Inspection & Safety Precautions
POWTRAN PI8000 frequency inverters have been tested and inspected before leaving the
manufacturer. Before unpacking the product, please check if its package is damaged due to careless
transportation, and if the specifications and type of the product complies with the order. Please
contact the supplier of POWTRAN products if any problems are found.
1-1. Inspection after Unpacking
Inspect that the contents are complete (one unit of PI8000/8100 frequency inverter, one
operation manual(with a copy of warranty card), one maintaince tips card).
Check the nameplate on the side of the frequency inverter to ensure that the product you
have received is right the one you ordered.
1-1-1. Name plant Instruction 1
Input Spec.
Output Spec.
Serial No.& Bar Code
AC Motor Drivers Model PI8000 004G3
POWTRAN TECHNOLOGY CO.,LTD.
3 380V 50-60Hz
4KW 8.5A 0.00-400.0Hz
Z1001A00001
TYPE:
OUTPUT:
SOURCE:

1-1-2. Model description 2:
PI 800 0 b 004 G 3
Input voltage level
1: single-phase 220V 2: 3-phase 220V
3: 3-phase 380V 4: 3-phase 460V
5: 3-phase 575V 6: 3-phase 660V
9: 3-phase 1140V
class code:
0: normal configuration
1:spetial 1 configuration
2:spetial 2 configuartion
POWTRAN
INVERTER
type code
a: normal (elided)
b: inhanced m: mini
d: single board
Serial Name
PI800: PI8000 Serial
PI801: PI8100 Serial
Function Code()
General Type F: Flow load
G: General load
M: Middle load
H: Heavy load
Special Type S:
TEXDRIVE
T: WINDLASS
Z: JETDRIVE
Applicable motor
capacity()
e.g.7R5: 7.5KW
4: 4KW

1-2. Safety Precautions
Never connect the A.C. power supply to the output terminals (U, V, W) of the frequency
inverter.
Fix and lock the panel before supplying power so as to avoid the danger caused by the poor
capacity or other components inside the inverter.
After the power supply is switched on, do not perform wiring or check, etc.
Dont touch the circuit boards or its parts or components in the inverter when it is powered,
so as to avoid danger of electric shock.

Section I Inspection & Safety Precaution
2

S
e
c
t
i
o
n

I

If the power supply is switched off, do not touch the PCB or other parts inside the inverter
within 5 minutes after the keyboard indicator lamp goes off, and you must check by using
the instrument that the inverter has completely discharged all its capacity before you start to
work inside the inverter. Otherwise, there will be the danger of electric shock.
The static electricity in human body will cause serious damage to the MOS field effect
transistor in the inverter. Please keep your hands away from the PCB, IGBT and other
internal parts before taking actions to prevent static electricity. Otherwise, faults may be
caused.
In use, the earthing terminal ( ) of the frequency inverter must be grounded to the earthing
connections correctly and securely according to the national electrical safety specifications
and other applicable standards.
Please dont shut off the unit by turning off the power supply. Turn off the power supply
after the motor has stopped its operation.
Meet CE standard with EMI filter.
1-3. Application
Powtran inverter is generally applied to 3 phase AC asynchronism motors.
Powtran inverter is applied to the admisive occasion, the occasion where is not admissive
may lead to fire, electric shock, explosion and so on.
If the inverter seizes up when it is applied to the equipment which may lead danger (e.g. lift
tools of transportation, aviation system, saftety equipment, etc), it should be managed
carefully. Do inquire the factory when it happens.

Only the well-trained personnel are allowed to use this unit, and such
personnel must read through the parts of this manual relating to the safety,
installation, operation and maintenance before using the unit. The safe
operation of this unit depends on correct transport, installation, operation
and maintenance!

3

S
e
c
t
i
o
n

I
I

Section II. Installation & Standby Circuit
2-1. Conditions for Use
1) Ambient temperature -10~40.
2) Avoid electromagnetic interference and keep the unit away from the interference source.
3) Prevent dropping water, steam, dust, powder, cotton fiber or fine metal powder from entering it.
4) Prevent oil, salt and corrosive gas from entering it.
5) Avoid vibration.
6) Avoid high temperature and moisture and avoid being wetted due to raining, with the humidity
below 90%RH (not dewing).
7) Prohibit the use in the dangerous environment where inflammable or combustible or explosive
gas, liquid or solid exists.
2-2. Installation
The frequency inverter must be installed by wall hooking in the indoor room with adequate
ventilation, with enough space left between it and the adjacent objects or damper (walls) surrounding
it, as shown in the below figure:
OUT
1
5
0
m
m
50mm 50mm
PRG
FWD MF2 MF1
ESC STOP/RESET
SET
DIGITAL PANEL
+
-
+
E
N
T
E
R
ALARM
V
A
Hz
s
%
C
-
FWD REV
S00
0.00 0.0
S01
S10 PID
WARNING
Read the operation manual before adjust or inspect.
High voltage inside.Maintained by the well-trained
personnel.
Confirm the input and output dc control cables are
well connected.
Adjust or inspect the inner circuits after power down
and discharge.
OUT
IN IN
1
5
0
m
m
or more
AIR
or more
o
r

m
o
r
e
o
r

m
o
r
e

2-3. Wiring
The wiring of frequency inverter includes two parts: main circuit and control circuit. The user
must ensure correct connections according to the following connection diagram.
Section II Intallation & Standby Circuit
4

S
e
c
t
i
o
n

I
I

2-3-1. PI8000 Diagram
1. Wiring diagram 11kW ~15kW and below (8N2)

Section II Inspection & Standby Circuit
5

S
e
c
t
i
o
n

I
I

2. Wiring diagram 18.5kW~355kW(8N3/8N4 /8N5 /8N6 /8N7 /8N8 /8N9 /8NA /8NB)

6

S
e
c
t
i
o
n

I
I

2-3-2. PI8100 Diagram
1. Wiring diagram 11kW and below (7N2 /7N3 /7N4)

7

S
e
c
t
i
o
n

I
I

2-4. Main Circuit Terminals(G Series)
2-4-1. PI8000 Main Circuit Terminals
1. 11~15kW(380V)Main Circuit Terminals

2. 18.5~37kW(380V)Main Circuit Terminals

T/L3
AC Input Line
Terminals
R/L1 S/L2
Motor connection
W/T3 V/T2 U/T1 DC+1 DC+2 DC- /E
DC+1/DC+2:DC Resistance
DC+2/DC- :Braking unit

Note: DC+1/DC+2 Standard setting is short circuit; if it is with external reactance, please disconnect
and then connect it.
8

S
e
c
t
i
o
n

I
I

2-4-2. PI8100 Main Circuit Terminals
1. 7.5kW below(380V)Main Circuit Terminals

Note: The above kW categaries are for G type inverter.
2-4-3. Terminal Function
Terminal Description Functions
R/L1
Power input for
frequency inverter
Connected to 3-phase power
(Single input connected to R, T)
S/L2
T/L3

Grounding point Grounded to the earth
B1, B2
Connection point for
braking resistance
Connect brake resistance
U/T1
3 Phase Output Connected to 3-phase motor V/T2
W/T3
DC+2, DC- DC Bus output Connect the brake brake unit.
DC+1, DC+2
DC reactance connection
terminal.
Connect DC reactance (No short circuit).
2-5. Control Circuit Terminals
2-5-1. Control Circuit Terminals Description
Classify Terminal Description Functions
Input
signal
DI1 DI1 Input Terminal
Multi-functions input terminal.For details
Please read o36~o46
DI2 DI2 InputTerminal
9

S
e
c
t
i
o
n

I
I

Enter a valid polarity can be controlled by o47
DI1~DI4 Drive model can be controled by JP4
Above 11kW:
DI5~DI8Drive model can be controled by PLC
output terminal
DI6 can as digital pulse input
Below 11kW:
DI5~DI6Drive model can be controled by PLC
output terminal
DI6 can as digital pulse input
PLC
PLC Control
Terminal
PLC Control DI5~DI8 Drive model
Drain Drive : PLCconnect 24VDC or externa
lpower
Source Drive: PLC connect COM
Assistant
Power
24V Power positive
The biggest output 24V/200mA, Can not
connect COM with GND in any situation
COM Common terminal
Output
signal
SPA/COM Output signal 1
Open Collector signal when the output action
(24VDC/50mA)
Common terminal COM , the output function
can set by o21, o22
SPA ,SPB provide hi-speed pulse output fun -
ction.
After setting functions by o61~o64,Frequency
inverter will take effect again.
SPB/COM Output signal 2
TA1/TB1/TC1 Output signal 3
TA1-TC1open, TB1-TC1close, the output fun -
ction can set by o23
TA2/TB2/TC2 Output signal 4
TA2-TC2open, TB2-TC2close, the output
function can set by o24
Analog
input
signal
+10V, GND Analog power +10V, 50mA
AI1
Multifunction Analog
input signal 1
JP5 cut/JP3 1-2: -10V~+10V
JP5 cut/JP3 2-3: 0~10V
JP5 connect: 0~20mA can be regulated
o00/o01 Set the input voltage / current range
o06/o07 Set the input signal corresponding to
set value
AI2
input signal 2
JP6cut: 0~10V
JP6connect: 0~20mA can be regulated
o02/o03can set input voltage/ current arrange
set value
AI3
input signal 3
JP7cut: 0~10V
JP7connect: 0~20mA can be regulated
o04/o05can set input voltage/ current arrange
set value
DA1
More function analog
output 1
JP1 1-2: 0~20mA
JP1 2-3: 0~10VDC
o15 Set analog output analog functions
o17/o18set the output signal arrange
10

S
e
c
t
i
o
n

I
I

DA2
More function analog
output 2
JP2 1-2: 0~20mA
JP2 2-3: 0~10VDC
o16 Set analog output analog functions
o19/o20 set the output signal arrange
2-5-2. Control circuit terminal
1. 8KLCB Control circuit terminal

2. 8KSCB Control circuit terminal

2-6. Connection Precautions
Dont install power factor capacitance or resistance-capacitance absorbing device between
the output terminals U, V, W of the frequency inverter.
To disassemble or replace the motor, the input power supply must be turned off for the
frequency inverter.
Do not drop Metal scrap foam or lint into the frequency inverter, otherwise the machine will
be faulted.
The motor or power supply can be switched on/off only after the inverter stops its output.
In order to minimize the effect of electromagnetic interference, a surge absorbing device
should be installed if used electromagnetic contactor and relay, etc. is near to the frequency
inverter.
For external control of frequency inverter, a isolation device should be used for the control
lines or screened cable should be used.
A screened cable should be used as the signal connection line for input command and must
be routed separately as well, and it had better be installed far from the main circuit.
When the carrier frequency is less than 3kHz, the distance between the frequency inverter
and motor must not be greater than 50 meters (maximum). When it is above 4kHz, this
distance should be reduced. The cable for this connection had better be laid in metal conduit.
If the frequency inverter is equipped with peripheral devices (such as filter, reactor), first
measure its insulation resistance to the earth with 1000V megohm meter, and ensure the
resistance value is not below 4M.
11

S
e
c
t
i
o
n

I
I

If the frequency inverter must be started frequently, dont switch off its power supply, and
the operator must start or stop the inverter by using the COM/FWD of the control terminal
or Keyboard or RS485, in order to avoid damage to the bridge rectifier.
Dont connect A.C. input power to the output terminals U, V, W of the frequency inverter.
In order to prevent unexpected accidents, earthing terminal E or must be grounded to the
earth securely (the grounding resistance should be below 100). The cable size should be
greater than half of below- mentioned corresponding cable size; otherwise current leakage
will happen possibly.
For wiring of main circuit, please refer to national rule.
Capacity of the motor should be equal to or smaller than that of the inverter.
Specification of MCCBelectric cable and contractor
Type MCCB(A)
In/out Cable
(Copper Core)mm
2

Rated Operational Current Of
Contractor A(voltage:380V or 220V)
PI8100 R40G2 10A 1.5 10
PI8100 R75G2 16A 2.5 10
PI8100 1R5G2 20A 2.5 16
PI8100 2R2G2 32A 4 20
PI8100 004G2 40A 6 25
PI8100 5R5G2 63A 6 32
PI8000 7R5G2 100A 10 63
PI8000 011G2 125A 10 95
PI8000 015G2 160A 25 120
PI8000 018G2 160A 25 120
PI8000 022G2 200A 25 170
PI8000 030G2 200A 35 170
PI8000 037G2 250A 35 170
PI8000 045G2 250A 70 230
PI8000 055G2 315A 70 280
PI8000 R75G3 10A 1.5 10
PI8000 1R5G3 16A 1.5 10
PI8000 2R2G3 16A 2.5 10
PI8000 004G3 25A 2.5 16
PI8000 5R5G3 25A 4 16
PI8000 7R5G3 40A 4 25
PI8000 011G3 63A 6 32
PI8000 015G3 63A 6 50
PI8000 018G3 100A 10 63
PI8000 022G3 100A 10 80
PI8000 030G3 125A 16 95
12

S
e
c
t
i
o
n

I
I

PI8000 037G3 160A 25 120
PI8000 045G3 200A 35 135
PI8000 055G3 250A 35 170
PI8000 075G3 315A 70 230
PI8000 093G3 400A 70 280
PI8000 110G3 400A 95 315
PI8000 132G3 400A 95 380
PI8000 160G3 630A 150 450
PI8000 187G3 630A 185 500
PI8000 200G3 630A 240 580
PI8000 220G3 800A 150*2 630
PI8000 250G3 800A 150*2 700
PI8000 280G3 1000A 185*2 780
PI8000 315G3 1200A 240*2 900
PI8000 355G3 1280A 240*2 960
PI8000 400G3 1380A 185*3 1035
PI8000 500G3 1720A 185*3 1290
2-7. Standby circuit
When the fault or trip of the inverter may cause great loss or accident, please add the standby circuit.
Note:confirm and test the running characteristic of the standby circuit, in order to ensure the industrial
phase and the converter phase are in the same direction.
T
R
S
Inverter
R
Interlock relay
PI8000
3-PHASE
AC POWER
SUPPLY
M
3~
T
S
U
V
W
MCC1
MCC2

13

S
e
c
t
i
o
n

I
I
I

Section III. Operating Keyboard
2-8. Operating keyboard
3-1-1. JP6E8000 specification and function description(Standard)

+
-
DIGITAL PANEL
FWD REV ALARM
+
-
Hz
A
V
%
s
E
N
T
E
R
PRG
ESC
MF1 MF2 FWD
SET
STOP/RESET
Reset /Stop Key
* drive stop running
* Exception Reset
* fault confirmation
Forward running key
* drive forward running
Forward Indication Light
* ONforward indication
* OFFnot forward indication
* FLASHforward accelerating
Alarm Indication
Light
* ONfaulty
* OFFgood
* FLASHprevious
fault was not
confirmed
Acceleration Select/Parameter
Setting Key
* press SET key and rotate JOG key
while selecting parameter, the
parameter location changes to 10
* finish and save the value changes
* change the object under monitor
Quit Key
* exit the revisement of
parameter
* reture to displaying menu
from submenu or functional
menu
* exit default state
Positive And Negative Sign Indication
Light
* just for monitor select
Parameter Setting/Shift Key
* start to change parameter
* Functions value adjustments
Modification bit
Multi-function Key MF1/MF2
* MF1 define functions through parameter
A43
A44
* A43/A44=0 MF defined as plus function
* A43/A44=1 MF defined as minus function
* A43/A44=2 MF defined as free stop
function
* A43/A44=3 MF defined as forward
function
* A43/A44=4 MF defined as reverse
function
* A43/A44=5 MF defined as Punctuality
dynamic function
* A43/A44=6 MF defined as Anti-Jog
function
* A43/A44=7 MF defined as Jog function
* A43/A44=8 MF defined as Up function
* A43/A44=9 MF defined as Down function
ENTER
* have the same function with PRG/
refer to explaination of key PRG/
* Invalid in the monitoring state
Monitor Select 1 Numerical Display
* display the corresponding values of the
function under query status
* display fault code under fault condition
* display the object set byA00 monitor
select while running
Potentiometer Key
* under checking state, the
function items value has been in
increment or decrement
* under revising state, the edit bit
of function items value has been
in increment or decrement
* under monitoring, setting
frequency to increase or decrease
Reverse Indication Light
* ONreverse indication
* OFFnot reverse indication
* FLASHreverse accelerating
Data Unit Prompt Light
*composed of three indication
lightslocated on the right side of
the LED digital tubeDisplay
status corresponding to the six
unitsindicate the unit of the
parameters displayed by LED
*the correspondence is as
following
OFF
ON
C S %
V A Hz
S
V
%
A C
Hz
UNIT UNIT
Hz
C A
%
V
S
S
V
%
A C
Hz
UNIT
UNIT
Hz
C A
%
V
S
S
V
%
A C
Hz
UNIT UNIT
Hz
C A
%
V
S
NO UNITS
S
V
%
A C
Hz
UNIT
Section III Operating Keyboard
14

S
e
c
t
i
o
n

I
I
I

3-1-2. JP6C8000 keyboard specification and function description(Optional)
Data Unit Prompt Light
*composed of three indication
lightslocated on the right side of
the LED digital tubeDisplay
status corresponding to the six
unitsindicate the unit of the
parameters displayed by LED
*the correspondence is as
following
OFF
ON
C S %
V A Hz
S
V
%
A C
Hz
UNIT UNIT
Hz
C A
%
V
S
S
V
%
A C
Hz
UNIT
UNIT
Hz
C A
%
V
S
S
V
%
A C
Hz
UNIT UNIT
Hz
C A
%
V
S
NO UNITS
S
V
%
A C
Hz
UNIT
A00 Monitor Select 1
Forward Indication Light
* ONforward indication
* OFFnot forward indication
* FLASHforward accelerating
Positive And Negative Sign Indication Light
* just for monitor select
Parameter Setting/Shift Key
* start to change parameter
* Functions value adjustments
Modification bit
Multi-function Key MF1/MF2
A43
A44
* A43/A44=0 MF defined as plus function
* A43/A44=1 MF defined as minus function
* A43/A44=2 MF defined as free stop
function
* A43/A44=3 MF defined as forward
function
* A43/A44=4 MF defined as reverse
function
* A43/A44=5 MF defined as Punctuality
dynamic function
* A43/A44=6 MF defined as Anti-Jog
function
* A43/A44=7 MF defined as Jog function
* A43/A44=8 MF defined as Up function
* A43/A44=9 MF defined as Down function
Acceleration Select/Parameter
Setting Key
* press SET key and rotate JOG key
while selecting parameter, the
parameter location changes to 10
* finish and save the value changes
* change the object under monitor
Reset /Stop Key
* drive stop running
* Exception Reset
* fault confirmation
Forward running key
* drive forward running
ENTER
* have the same function with PRG/
refer to explaination of key PRG/
* Invalid in the monitoring state
* display the corresponding values of the
function under query status
* display fault code under fault condition
* display the object set byA00 monitor
select while running
Alarm Indication
Light
* ONfaulty
* OFFgood
* FLASHprevious
fault was not
confirmed
Quit Key
* exit the revisement of
parameter
* reture to displaying menu
from submenu or functional
menu
* exit default state
Potentiometer Key
* under checking state, the
function items value has been in
increment or decrement
* under revising state, the edit bit
of function items value has been
in increment or decrement
* under monitoring, setting
frequency to increase or decrease
Reverse Lndication Light
* ONreverse indication
* OFFnot reverse indication
* FLASHreverse accelerating
DIGITAL PANEL
FWD REV ALARM
+
-
Hz
A
V
%
s
E
N
T
E
R
PRG
ESC
MF1 MF2 FWD
SET
STOP/RESET
S00 Set Fre.
0.00
1 Actual Fre.
2 Motor AC
0.5
+
-

15

S
e
c
t
i
o
n

I
I
I

3-1. Example for parameters set
3-2-1. F01 keyboard set the frequency from 50.00Hz to 25.00Hz.
One Times
adjust the value
of parameter
revisement
Potentiometer
One Times
Or
One Times
Potentiometer
One Times
S00 Set Fre.
0.00
1 Actual Fre.
2 Motor AC
0.0
F00-63 Basic FG
PI8000 G00
PRG PRG
Or
ENTER
F00 Control Mode
0.00 0.0
0.00 0.0 0.00 0.0
PRG
ENTER
PRG
adjust the
parameters
Or
ENTER
F01Fre. Set By K
0.00 0.0
SET
0.00 0.0 0.00 0.0
Functional
adjustment
item
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
F01Fre. Set By K F01Fre. Set By K
F01Fre. Set By K F01Fre. Set By K

1. Under monitoring status, press
PRG
into parameter group to query status;
2. Through potentiometerSwitch to F00-63 Basic FG;
3. Press
PRG
, or ENTER, enter into F00-63 Basic FG parameter group to query status;
4. Through potentiometerSwitch to F01Fre. Set by K;
5. Press
PRG
, or ENTER, enter into F01 Fre. Set by K parameter modify status;
6. Through
PRG
, or ENTER, adjust the value is modified bit;
7. Through potentiometerHas been modified to adjust the bit values;
8. Finish the adjustment, press
SET
;if cancle the change, press
ESC
to escape to the modify
status;
9. Press
ESC
to exit to previous menu .
16

S
e
c
t
i
o
n

I
I
I

3-2-2. Parameter upload to the keyboard
Parameter Item Description
y01 parameter upload
to the keyboard
N function 0
System parameter upload to the memory area1 in the keyboard 1
Clear memory area in the keyboard1, 2, 3, 4 5
y01 P Upload K y00 Reset SP
y01 P Upload K P Upload K y01 P Upload K
to adjust the
value of
resivement
One Times
One Times
One Times
Potentiometer
Potentiometer
Potentiometer
0.00 0.0 PI8000 G00
PRG
0.00 0.0 0.00 0.0
PRG
Or
ENTER
SET
USE MEMORY 3RD
100%-END
STOP-END
y00-23 System FG
PI8000 G09
PRG
y01 P Upload K
0.00 0.0
0.00 0.0 0.00 0.0
Upload
Finished
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
S00 Set Fre. F00-63 Basic FG

Example . System parameter upload to the memory area3 in the keyboard
PRG
into parameter group to check status;
2. Through potentiometerSwitch to y00-23 System FG;
3. Press
PRG
, or ENTER, enter into y00-23 System FG parameter group to check status;
4. Through potentiometerSwitch to y01P Upload To K;
5. Press
PRG
, or ENTER, enter into y01P Upload To K parameter modify status;
6. Through potentiometer adjust value to be 3 ;
SET
;the speed for upload will display on the LED;if cancle the
change, press
ESC
to escape to the modification status;
8. Press
ESC
to exit to previous menu.
17

S
e
c
t
i
o
n

I
I
I

3-2-3. Reset system parameters
y00 Reset system
parameters
N function 0
memory area1 in the keyboard to reset system parameter 1
memory area4 in the keyboard 1to reset system parameter 4
Use the factory setting reset system parameter 5

PRG
One Times
y00-23 System FG
y00 Reset SP y00 Reset SP
to adjust
the value
of
resivement
One Times
One Times
One Times
Potentiometer
Potentiometer
y00 Reset SP
0.00 0.0
1 Actual Fre.
2 Motor AC
0.00 0.0 PI8000 G00
PRG
0.00 0.0
SET
P Donload K
USE MEMORY 3RD
100%-END
STOP-END
PI8000 G09
PRG
y00 Reset SP
0.00 0.0 0.00 0.0
Download
Finished
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
S00 Set Fre. F00-63 Basic FG

Example 1: memory area3 in the keyboard 1 to reset system parameter
PRG
into parameter group to query status
3. Press
PRG
, or ENTER, enter into y00-23 System FG parameter group to query status;
5. Press
PRG
, or ENTER, enter into y00 Reset SP parameter modify status;
6. Through potentiometer adjust to 3 ;
SET
;the speed for download will display on the LED;if cancle the
change, press
ESC
;
8. Press
ESC
18

S
e
c
t
i
o
n

I
I
I

Example 2 Clear memory area 1, 2, 3, 4 in the keyboard
0.00 0.0 PI8000 G00
PRG
0.00 0.0 0.00 0.0
PRG
ENTER
SET
PI8000 G09
PRG
0.00 0.0
0.00 0.0 0.00 0.0
Clearance
Finished
0.00 0.0
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
1 Actual Fre.
2 Motor AC
S00 Set Fre. F00-63 Basic FG y00-23 System FG
y00 Reset SP
adjust the value
of parameter
revisement
Potentiometer
One Times
One Times
One Times
Or
y01P Upload To K y01P Upload To K
y01P Upload To K y01P Upload To K y01P Upload To K
Potentiometer
Potentiometer

PRG
into parameter group to check status
3. Press
PRG
, or ENTER, enter into y00-23 System FG parameter group to check status;
5. Press
PRG
, or ENTER, enter into y01P Upload To K parameter modify status;
6. Through potentiometer adjust to 5 ;
SET
;the speed for Clear memory area will display on the LED;if
cancle the change, press
ESC
;
8. Press
ESC
3-2-4. F02 the main set mode of set frequency is set to 4, keyboard potentiometer setting !
1. Under monitoring status, Through potentiometer adjust the frequency, the resolution ratio
potentiometer is 0.05Hz.
2. Range of set frequency can be set with the following parameters:
Parameter item Description
F12 max. frequency
Inverter output maximum frequency allowed Setting range:
10.00~320.00Hz
19

S
e
c
t
i
o
n

I
I
I

A45 keyboard potentiometer
setting X1
Keyboard potentiometer setting the start value
Setting range: 0~100%
setting X2
Keyboard potentiometer setting the end value
setting value
Display the value of potentiometer setting, range: A45~A46
Also can set diretly, Setting range: A45~A46
setting X1correspond to Y1
Keyboard potentiometer setting the starting point for the corresponding
value
Setting range: -100%~+100%
setting X2 correspond to Y2
Keyboard potentiometer settings corresponding to the value of the end
S00 setting frequency
Displays the current size of the set frequency,through the potentiometer
setting
Setting range: F12*A48~ F12*A49
Example:
F12=50.00Hz, A45=0%, A46=100%, A47 Shows the value of potentiometer settings 0%~100%,
Numerical size can be adjusted by potentiometer.
(1) when A48=0%, A49=+100%, S00 Set Fre.range 0.00Hz~50.00Hz.
(2) when A48=0%, A49=+50%, S00 Set Fre.range 0.00Hz~25.00Hz.
(3) when A48=-100%, A49=+100%, S00 Set Fre.range -50.00Hz~50.00Hz.
Note: when the motor is in -50.00~0Hz realise reverse, another setting
F45 Ten bit motor forward inverse as
1 Command priority: Analog given positive and negative values, on the F45 details refer to F45
Parameter Description
3-2-5. F02 the main set mode of set frequency is set to 1, AI1 external analog given.
1. Under monitoring status, Through external analog input terminal Al1 adjust the frequency, the
resolution ratio is 0.01Hz.
2. Set the frequency range can be set with the following parameters:
F12 most frequency
Inverter speed adjustments allowed maximum output frequency Sett -
ing range: 10.00~320.00Hz
o00 AI1 input X1
Keyboard potentiometer setting the start value
o01 AI1 input X2
Keyboard potentiometer setting the end value
o06 AI1 input X1
correspond to Y1
Keyboard potentiometer setting the starting point for the corresponding
value
o07 AI1 input X2
correspond to Y2
Keyboard potentiometer settings corresponding to the value of the end
S00 frequency setting
Display the frequency,Through out analog input terminal Al1 adjust the
frequency
20

S
e
c
t
i
o
n

I
I
I

Setting range: F12*o06~ F12*o07
Example:
F12=50.00Hz, o00=0%, o01=100%,
(1) When o06=0%, o07=+100%, S00 Set Fre.range 0.00Hz~50.00Hz.
(2) When o06=0%, o07=+50%, S00 Set Fre.range 0.00Hz~25.00Hz.
(3) When o06=-100%, o07=+100%, S00 Set Fre.range -50.00Hz~50.00Hz.
Note: When realize the motor reverse in -50.00~0Hz
F45Ten bit motor forward reverse as
1 Command priority: Analog given positive and negative values, on the F45 details see F45
Parameter Description

21

S
e
c
t
i
o
n

I
V

Section IV. Test Running
Failure occurred when test running, Please take reference of fault diagnosis in 6-1 to get rid
of the breakdown
Inverter parameters have a strong adaptive ability, in general b11 = 1 calculation of electrical
parameters with the name plate, on this basis, a little manual adjustment can get you
high-performance vector control.
Only when the motor completely without the load can set b11=3motor rotation measurements
Before the electrical parameter measurement finished, inverter can have the ourput voltage
any time, please ensure the safety.
Section IV Test Runing
22

S
e
c
t
i
o
n

I
V

test
running
power voltage inverter in the
rated input voltage range
power supply connect to RST of inverter, confirm
the correct grounded then supply power
Confirmed the inverter power matches to the
motor power ,reset the factory value of y00 =5
Select motor parameters, motor parameters set in accordance
with motor nameplate set of parameters, rated power, rated
current, rated voltage, the number of pole pairs, motor speed
Set the appropriate acceleration and deceleration time, the motor
maximum frequency F12, the fundamental frequency F15
Set the keyboard for a
given frequency of F01
Press the keyboard keys
are transferred to run FWD
Shut down power outages, swap
any two-phase motor line
Shut down after the motor
parameter tuning
b11=3
Measurement
converter operation
b11=2
Static frequency converter
measurement
b11=1
Calculated using plate
Press FWD self-tuning start
(motor may be running safety)
forward running
direction of the motor
V/F
Control
sensorless
vector
control
Sensor
vector
control
The success of self-tuning
Choose
F00Control mode
Set the appropriate F09/F10 acceleration
and deceleration parameters, F06/F07
torque control parameter
Y
N
Y
N
Section IV Test Runing
23

S
e
c
t
i
o
n

I
V

According to parameter
setting F06 V / F boost
mode
Set F07 torque
boost value
setting F01
running frequency
running
observe running current
and motor state
parameters
optimization
Normal
operation
Stop and test
running finish
upper torque
setting
running
Observe the motor current,
excitation component, torque
fluctuation component
Stop and test
running finish
Upper torque
setting C13C14
Set PG pulses C28PG
directions C30
running
Observe motor
speed S06
Observe the motor current,
excitation component, torque
fluctuation component
Stop and test
running finish
Y
N
Y
N
Y
N
Y
N
V/F
Control
sensorless
vector
control
sensor
vector
control
Normal
operation
Normal
operation
Normal
operation
adjust speed loopC01-C07
Turned around differential
gain C09-C12regulate
motor parameters
parameters
optimization
adjust speed loopC01-C07
Turned around differential gain
regulate motor parameters
parameters
optimization

24

S
e
c
t
i
o
n

V

Section V Parameter Function Table
Notice: mean that the factory setting value of the parameter is according to the power and model.The
exact value is referred to the Parameter Function Table.Change limited mean that whether it can be modified
while running.
5-1. Functional parameter list
5-1-1. Menu Group
Code Description / LCD Function Discription
Group
ID
Reference
page
S Monitor Function Group
Monitor frequency, current and other 16
monitor objects
0B 54
F Basic Function Group
Frequency setting, control
mode,accelerationtime and deceleration time
00 55
A User Function Group Monitor, protection, communication setting 01 70
o IO Function Group Analog, digital input, output function 02 82
H Multi-speed PLC Group Multi-speed running, PLCrunning 03 100
U V/F parameter Group User defined V/Fcurve 04 108
P PID Function Group Internal PID parameter setting 05 109
E Extend Function Froup
Constant pressure water supply and other
functions setting
06 112
C
Speed ring function
group
Current ring, speed running, PGparameter 07 118
b Motor parameter group Motor parameter setting 08 123
y System Function Group
Parameter reset, fault query, product
information, parameter protection
09 126
5-1-2. Monitor function:S00-S15(0x0B00-0x0B0F)
Code Description / LCD Setting Range
Factory
Setting
Change
Limited
Reference
page
S00 Setting Frequency
current inverter real setting
frequency
- N 54
S01 Real Frequency
current inverter real output
frequency
- N 54
S02 Motor real Current Valid value of motor actual current - N 54
S03
Percentage of Motor
Current
The percentage of actual motor curr
- ent and rated current
- N 54
S04 DC Bus Voltage Detection value of DC bus voltage - N 54
S05 The Output Voltage The real output voltage - N 54
S06 Motor Real Speed Motor real running speed - N 54
S07 Total Running Time
The total running time for every
time
- N 54
S08 IGBT Temperature
Test the temperature of IGBT in the
frequency
- N 55
25

S
e
c
t
i
o
n

V

S09 PID Set Point
PID Adjust run-time values of the
percentage of a given
- N 55
S10 PID Feedback
percentage of feed back
- N 55
S11 Motor Output Frequency
The percentage of actual output
power of motor
- N 55
S12
Excitation Heft Set
Value
Motors set excitation heft
percentage
- N 55
S13
Excitation Heft Actual
Value
Motors actual excitation heft
percentage
- N 55
S14 Torque Heft Set Value Motor set torque percentage - N 55
S15 Torque Heft Actual Value
Motor actual torque hefts
percentage
- N 55
5-1-3. Basic function Group:F00-F50(0x0000-0x0032)
Factory
Setting
Change
Limited
Reference
page
F00 Control Mode
V/Fcontrol 0
0 N 55
Sensorless vector control 1
Sensor feedback close loop
vector control
2
F01
Keyboard Setting
Frequency
Lower frequency~upper frequency 50.00 Y 55
F02
Frequency Main Set
Mode
Keyboard setting frequency
or RS485
0
0 Y 55
AI1 the external analog setting 1
Keyboard potentiometer setting 4
Multi-segment digital
voltage setting
5
Digital Pulse Setting 6
F03
Auxiliary Setting Mode
Of Frequency
Keyboard setting frequency
or RS485
0
0 Y 56
voltage setting
5
Digital Pulse Set 6
PID regulation mode 7
F04
The Relationship
Between Main And
Auxiliary Setting
Frequency
The main setting individual
control
0
0 Y 57
The auxiliary setting
individual control
1
26

S
e
c
t
i
o
n

V

main + auxiliary 2
main -auxiliary 3
(main *auxiliary)/maximum
frequency
4
Maximummain, auxiliary 5
Minimummain, auxiliary 6
F05 Running Control Mode
Keyboard+Rs485/CAN 0
0 Y 58
Keyboard+terminal+Rs485/CAN 1
Rs485/CAN 2
Terminal control 3
The proportion linkage control 4
F06 V/F Boost Mode
1 bit
Beeline V/Fcurve 0
0000 N 59
Power of 1.2
V/Fcurve
1
Power of 1.7 power
V/Fcurve
2
Power of 2 powerV/Fcurve 3
Define mode V/Fcurve 4
10 bit
Close Automatic
torque boost
0
Automatic
torqueboost
1
100 bit
VF mode 0 Speed No
Output
0
VF mode keep 0 speed 1
F07 Torque boost Value 0.0~30.0% 0.0 Y 59
F08
Torque Boost Cut-off
Frequency
0.00~Maximum frequency 15.00 Y 59
F09 Accelerate Time 0.0~3200.0 10.0 Y 60
F10 Decelerate Time 0.0~3200.0 10.0 Y 60
F11
Percentage Of Output
Voltage
50~110 100 Y 60
F12 Maximum Frequency 10.00~320.00 50.00 N 60
F13 Lower Frequency 0.00~Upper frequency 0.00 N 60
F14 Upper Frequency Lower frequency~Upper frequency 50.00 N 60
F15 Basic Frequency 5.00~Maximum frequency 50.00 N 61
F16 Carrier Frequency 1.0~16.0 Y 61
F17
Carrier Frequency
Adjustment Range
0.0~4.0 0.0 Y 62
F18
Carrier Frequency
Adjustment Mode
1 bit
No automatic
adjustment
0
00 Y 62
automatic adjustment
Mode
1
27

S
e
c
t
i
o
n

V

10 bit
automatic adjustment,
Fixed mode
0
random mode
1
F19
Waveform Generation
Mode
Asynchronous space-vector
PWM
0
0 N 62
Stepless & subsection
synchronous space vector
PWM
1
two-phase optimization
space vector PWM
2
F20
S Curve Start Time At
The Acceleration Step
0.0~50.0 0.0 Y 62
F21
S Curve Stop Time At
The Acceleration Atep
0.0~50.0 0.0 Y 62
F22
The Deceleration Step
0.0~50.0 0.0 Y 62
F23
0.0~50.0 0.0 Y 62
F24
V/F Control Slip
Compensation
slip compensation invalid 0
0 N 63
slip compensation valid 1
F25
Minimum Running
Frequency
0.00~maximum frequency 0.00 N 63
F26
DC Braking Current
When Starting
0~135 100 Y 64
F27
Braking Time When
Starting
0.0~60.0 0.0 Y 64
F28
Stop When The DC
Braking Current
0~135 100 Y 64
F29
Stop And Braking Wait
Time
0.0~60.0 0.0
Y
64
F30 Brake Time Stop 0.0~60.0 0.0 Y
64
F31
Stop And Brake Starting
Frequency
0.00~most frequency 0.00 Y 64
F32 Stop Setting Mode
Deceleration stop 0
0 N 65
Free stop 1
F33 Jog Acceleration Time 0.0~3200.0 1.0 N 65
F34 Jog Deceleration Time 0.0~3200.0 1.0 N 65
F35 Jog Mode Setting
1 bit
Jog direction: forward 0
000 N 65
Jog direction: reverse 1
Jog direction:
direction determined
by the main terminal
2
10 bit
Jog end mode: Stop
Running
0
Jog end mode:reset to
the former state before
1
28

S
e
c
t
i
o
n

V

jog
100
bit
Jog end and
acceleration
deceleration time:
reset to the set
acceleration and
deceleration time
before jog
0
Jog end and acceleration
deceleration time:save
the set acceleration and
deceleration time before
jog
1
F36 Jog Frequency Setting Lower frequency ~upper frequency 6.00 Y 66
F37 Skip Frequency1Limit 0.00~Maximum frequency 0.00 Y 66
F38 Skip Frequency1Upper 0.00~Maximum frequency 0.00 Y 66
F43 Preset Frequency 0.00~Max frequency 0.00 Y 67
F44
Preset Frequency
Working Time
0.0~60.0 0.0 Y 67
F45
Motor Running
Direction
1 bit
Direction command:
forward command
FWD let motor
forward running
0
0100 N 67
Direction command:
forward command
FWD let motor
reverse running
1
10 bit
Command prior:
terminal/keyboard
0
Prior command:
Analog given positive
and negative values
1
100
bit
Reverse allow: reverse
forbidden
0
Reverse allow: reverse
allow
1
F46 Pass 0 Stopping Time 0.0~60.0s 0 N 67
F47
Frequency Multiple
Setting
*1 0
0 N 68
*10 1
F48
Acceleration And
Deceleration
Configuration Word
1 bit
N adjustment of
acceleration time
0
0000 N 68
AI1 adjustment of the 1
29

S
e
c
t
i
o
n

V

external analog giving
AI2 adjustment of the
2
3
Adjustment of keyboard
potentiometer giving
4
Adjustment of Multi
steps digital voltage
giving
5
10 bit
N adjustment of
decceleration time
0
1
2
3
4
Adjustment of Multi
giving
5
100
bit
Acceleration time:*s 0
Acceleration time:*min 1
Acceleration time:*h 2
Acceleration time:*day 3
1000
bit
Deceleration time:*s 0
Deceleration time:*min 1
Deceleration time:*h 2
Deceleration time:*day 3
F49
Running Configuration
Word
1 bit
Running direction:
forward
0
0000 N 69
Running direction:
reverse
1
10 bit
Running time: *S 0
Running time: *Min 1
Running time: *H 2
Running time: *Day 3
F50
Energy Saving Running
Percentage
30~100 100 N 70
5-1-4. User Function Group:A00-A55(0x0100-0x0137)
Factory
Setting
Change
Limited
Reference
page
A00 Monitor 1
Parameter group Parameter group
0B00 Y 70
30

S
e
c
t
i
o
n

V

A01
A02
Monitor 2
Monitor 3
N: N: 0B01
0B02
Y
Y
X1000/X100 X10/ bit
00~0B 0~63(0x00~0x3F)
A03
Over /Less Voltage Stall
Protection
N 0
1 Y 71
Y 1
A04
Overvoltage Stall
Protection Voltage
110%~140%( Standard bus voltage) 120 Y 71
A05 Auto Stablize Voltage
Invalid 0
0 Y 71 Valid 1
Valid, usless for deceleration 2
A06 Dynamic Braking option
Invalid 0
0 Y 71 Security Type 1
General Type 2
A07 Hysteresis voltage 0~10% 2 Y 72
A08 Dynamic Braking Voltage 110%~140%( Standard bus voltage) 130 Y 72
A09 Less Voltage Level
60%~75%(Standard DC bus
voltage)
70 Y 72
A10
Power-down Tracking
Options
N 0
0 Y 72 Power-off tracking mode 1
Startup tracking mode 2
A11
Power-down tTracking
Time
0.0~20.0 0.0 Y 72
A12
Power Down Frequency
Drop Point
65~100%(standard DC bus voltage) 75 Y 73
A13
Drop Time
0.1~3200.0 5.0 Y 73
A14 Current Limit
N 0
0 Y 73
Y 1
A15 Limit Fall Time 0.1~3200.0 10.0 Y 73
A16
Limit Deceleration
Protection Point
10~250 Y 73
A17
Limit Fix-speed
Protection Point
10~250 Y 73
A18
Output Phase Lose
Protection
N protection of phase lost 0
0 Y 73
Warning and constant running 1
Warning and deceleration 2
Warning and free stopping 3
A19
Grade Of Phase Lose
Protection
10~100 30 Y 74
A20
Over Torque Inspected
Action
N torque inspection 0
0 Y 74 Warning and running 1
Warning and decelerating stop 2
31

S
e
c
t
i
o
n

V

A21 Over Torque Grade 10~250 Y 74
A22 Over Torque Inspection Time 0.0~60.0 0.1 Y 74
A23
Electronic Thermal
Relay Protection
Selection
N 0
1 Y 74
Y 1
A24
Electronic Thermal
Protection Grade
120~250 Y 74
A25 Fault Reset Times 0~10 0 Y 75
A26 Fault Reset Time 0.5~20.0 1.0 Y 75
A27 Fan Startup Temperature 0.0~60.0 0.0 Y 75
A28
This Inverter
Communication Address
1~128 8 Y 75
A29 Baud Rate
Baud rate is 1200 0
4 Y 75
Baud rate is 2400 1
Baud rate is 4800 2
Baud rate is 9600 3
Baud rate is 19200 4
A30 Communication Format
8, N, 1 for RTU 0
0 Y 76
8, N, 2 for RTU 1
8, E, 1 for RTU 2
8, O, 1 for RTU 3
8, E, 2 for RTU 4
8, O, 2 for RTU 5
A31
Communications
Troubleshooting
N warning for communication
fault
0
0 Y 76
Warning and running 1
A32 Delay Inspection Time
0: N inspection
10 Y 76
1~250: late inpsection
A33
Total Running Time
Setting
Auto clear to zero after power on 0
1 Y 76
Continue to accumulate
running time after power on
1
A34
Unit Of Total Running
Time
hour 0
0 Y 76
Day 1
A35
Motor Output Speed
Adjustment
0.1~1000.0 100.0 Y 76
A36
Adjustment Of Motor
Output Power
0.1~1000.0 100.0 Y 76
32

S
e
c
t
i
o
n

V

A37
Keyboard Lock
Function Options
0~0FF 0FF Y 77
A38 UP/DN Control
1 bit
Power down to save 0
0000 Y 77
Power down to clear
saving
1
10 bit
saving after stopping 0
Stop command to clear
saving
1
Cleared at the end of
stopping
2
100
bit
One-direction
adjustment
0
Double-direction
adjustment
1
1000
bit
Invalide adjustment 0
Valide adjustment 1
A39 UP/DN Time
1 bit
UP fix speed 0
0000 N 78
UP fix times 1
10 bit
DN fix speed 0
DN fix times 1
100
bit
UP N adjustmentof
speed ratio
0
1
2
3
adjustment of
Potentiometer giving
4
Adjustment of multi
-steps digital voltage
5
1000
bit
DN N adjustmentof
speed ratio
0
1
2
3
adjustment of
4
Adjustment of multi
5
A40 UP/DN Adjustment Value -300.00~300.00 0.00 N 79
A41 UP Adjustment Ratio 0.01~20.00 0.01 Y 79
33

S
e
c
t
i
o
n

V

A42 DN Adjustment Ratio 0.01~20.00 0.01 Y 79
A43
A44
The Definition Of
Multifunction Keys
MF1 And MF2
MF is defined as adding
function key
0
0
1
Y
Y
79
MF is definded as reducing
function key
1
MF is defined as free stopping key 2
MF is defined as FWD running
key
3
MF is defined as REV running
key
4
MF is defined as forward JOG
function key.
5
MF is defined as reverse JOG
function key.
6
MF is defined as JOG function
key.
7
MF is defined as UP function key 8
MF is defined as Down
function key.
9
UP / DN adjusted value reset 10
keyboard potentiometer
setting value resey
11
A45 Keyboard Potentiometer X1 0~100.0 0.0 Y 80
A46
Keyboard
PotentiometerX2
0~100.0 100.0 Y 80
A47
The Value Of Keyboard
Potentiometer Set
0.0~100.00 - Y 81
A48
Keyboard Potentiometer X1
Corresponding Value Y1
-100.0~100.0 0.00 Y 81
A49
Keyboard Potentiometer X2
-100.0~100.0 100.00 Y 81
A50
Keyboad Potentiometer
Control
1 bit
Saving after power down 0
0000 Y 81
Cleared after power down 1
10 bit
Saving after stoppoing 0
Clear saving after
stopping command
1
Clear saving at end of
stopping
2
100
bit
Reserved
1000
bit
Reserved
A51
Temperature Adjustment
Of Motor
0.0~200.0 100.0 N 81
A52
Over-heat Temperature
Of Motor
0.0~300.0 120.0 N 81
A53 Reaction For Motor N reaction for motor over-heat 0 0 Y 82
34

S
e
c
t
i
o
n

V

Over-heat
Warning and runing 1
Warning and deceleration
stopping
2
A54
Display Of Motor
Temperature
-50.0~300.0 - N 82
A55
Proportion Of Linkage
Ratio
0.10~10.00 1.00 Y 82
5-1-5. IO function group:o00-o68(0x0200-0x0244)
Factory
Setting
Change
Limited
Reference
page
o00 AI1 Input X1 0~100.0 0.0 Y 82
o01 AI1 Input X2 0~100.0 100.0 Y 82
o02 AI2 Input X1 0~100.0 0.0 Y 82
o03 AI2 Input X2 0~100.0 100.0 Y 82
o04 AI3 Input X1 0~100.0 0.0 Y 82
o05 AI3 Input X2 0~100.0 100.0 Y 82
o06
AI1 Input X1
-100.0~100.0 0.0 Y 82
o07
AI1 Input X2
-100.0~100.0 100.0 Y 82
o08
AI2 Input X1
-100.0~100.0 0.0 Y 82
o09
AI2 Input X2
-100.0~100.0 100.0 Y 82
o10
AI3 Input X1
-100.0~100.0 0.0 Y 82
o11
AI3 Input X2
-100.0~100.0 100.0 Y 82
o12 AI1 Input Filter Time 0.00~2.00 0.10 Y 84
o15
o16
DA1 Output Terminal
DA2 Output Terminal
N reaction 0
-
-
Y
Y
84
Setting frequency 1
Actual frequency 2
Actual current 3
Output voltage 4
DC bus voltge 5
IGBT temperature 6
Output power 7
Output RPM 8
35

S
e
c
t
i
o
n

V

Actual value of torque 9
o17
DA1 Adjustment Of
Lower Limit Output
0.0~100.0 0.0 Y 84
o18
DA1 Adjustment Of
Upper Limit Of Output
0.0~100.0 100.0 Y 84
o19
DA2 Adjustment Of
Lower Limit Output
0.0~100.0 0.0 Y 84
o20
DA2 Adjustment Of
Upper Limit Output
0.0~100.0 100.0 Y 84
o21
o22
o23
o24
O1 Output Signal
Option1
O2 Output Signal Option 2
No function 0
0
0
1
8
Y
Y
Y
Y
85
Fault warning 1
Over current inspection 2
Over load inspection 3
Over voltage inspection 4
Less voltage inspection 5
Low load inspection 6
Over heat inspection 7
Running state with command 8
Abnormal PID feedback signal 9
Motor state of REW running 10
Arrival of setting the
frequency
11
Arrival of Upper frequency 12
Arrival of Lower frequency 13
Arrival of FDT setting
frequency 1
14
frequency 2
15
FDT frequency level
inspection
16
Arrival of preset counter value 17
Arrival of upper limit counter 18
Program running one period
completed
19
Speed tricking mode inspecition 20
No command running state 21
REV running from inverter
command
22
Deceleration running 23
Acceleration running 24
Arrival of high pressure 25
Arrival of low pressure 26
Arrival of inverter rate current 27
36

S
e
c
t
i
o
n

V

Arrival of motor rate current 28
Arrival of input frequency
lower limitation
29
Arrival of current upper limitation 30
Arrival of current lower
limitation
31
Time to reach limit time 1 32
Inverter ready to run 34
o25 Output Signal Delay 1 0~32.000 0 Y
87
87
o27 Output Signal Delay 3 0~32.000
0 Y
87
87
o29 FDT Set Frequency 1 o30~Max frequecy 0.00 Y 87
o30 FDT Set Frequency 2 0~o29 0.00 Y 87
o31 FDT Inspection Range 0.00~5.00 0.00 Y 87
o32
Arrival Of Current
Upper Limitation
o33~200% 120 Y 88
o33
Arrival Of Current
Lower Limitation
o34~o32 20 Y 88
o34 Current Inspection Range 0~o33 3 Y 88
o35 Terminal Control Mode
1 bit
Two-wire running
control 1
0
0000 N 89
Two-wire running
control 2
1
Three-wire running
control 1
2
Three-wire running
control 2
3
One-shot operation
control 1
4
One-shot operation
control 2
5
10 bit
Terminal command
is invalid after power
on running
0
Terminal command
is valid after power
on running
1
o36
o37
o38
o39
o40
o41
(DI1) Input Terminal
Function Selection
Function Selection
(DI3 )Input Terminal
Function Selection
No function 0
0
0
0
0
0
0
Y
Y
Y
Y
Y
Y
91
Forward running FWD 1
Reverse running REV 2
3-line mode running STOP 3
Multi-segment command 1 4
37

S
e
c
t
i
o
n

V

o42
o43
o44
o45
o46
Function Selection
Function Selection
Function Selection
Function Selection
Function Selection
(AI1) Input Terminal
Function Selection
Function Selection
Function Selection
0
0
0
0
0
Y
Y
Y
Y
Y
Multi-segment command 7
Multi-segment speed command 1 8
Multi-segment speed command 9
Multi-segment digital voltage 1 11
The main set mode 1 of set
frequency
14
frequency
15
frequency
16
The auxiliary setting mode 1
of frequency set
17
of frequency set
18
of frequency set
19
MSS time running 1 20
Operation control mode shift 1 23
Forward torque limit shift 1 26
Reverse torque limit shift 1 29
Torque speed shift 32
fault reset command 33
FWD JOG command 34
REV JOG command 35
JOG order (as F35setting ) 36
Acceleration and deceleration
prohibition command
37
Motor 12 shift 38
38

S
e
c
t
i
o
n

V

Free stop 39
Up command 40
Down command 41
Automation program running
fuction cancel
42
stop
43
Program running start mode 44
Program running stop mode 45
Pulse counter clearance 46
Pulse counter input 47
Counter loading 48
Upper counter loading 49
External default signal input
(level)
50
1pump soft-start 51
1 pump stop 52
2pump soft-start 53
2 pump stop 54
3pump soft-start 55
3 pump stop 56
4pump soft-start 57
4 pump stop 58
handrotate command 59
Timing Water Supply change
to zero
60
Extruder acceleration and
deceleration direction
61
deceleration allowable
62
Limit time 1 input 63
Program switching to the next
segment
65
UP/DN adjusted value reset 66
Keyboard potentiometer set
value reset
67
(edge)
68
o47
Polarity of input and
output terminals
0000~F7FF 0000 Y 96
o48
Input Terminal Teponse
Time 0
0.001~30.000 0.005 Y 96
39

S
e
c
t
i
o
n

V

o49
Input Terminal Reponse
Time 1
0.001~30.000 0.005 Y 96
o50
Time Selection
0~07FF 0 Y 96
o51 Counter Collocation
1 bit
Circle counter operating 0
0 Y 97
Single cycle counter
running
1
10 bit
Arrive at upper
counter value and
reload
0
Arrive at upper
counter value and
clear savings
1
100 bit
Power on to reload 0
power on to clear
savings
1
power on to keep
previous count status
2
1000 bit
Count period 0
Output signal valid
time 20ms
1
Output signal valid
time 100ms
2
Output signal valid
time 500ms
3
o52
Maximum Pulse Input
Frequency
0.1~50.0 20.0 Y 97
o53 Current Counter Status 0~9999 0 Y 98
o54 Preset Counter Setting 0~ o55 0 Y 98
o55
Upper Limit Counter
Setting
o54~9999 9999 Y 98
o56
Virtual Terminal
Effective Selection
0000~F7FF 0000 Y 98
o57 DI1~4 Terminal Status 0000~1111 - Y 99
o58 DI5~8 Terminal Status 0000~1111 - Y 99
o59 AI1~3 Terminal Status 000~111 - Y 99
o60 O1~4 Terminal Status 0000~1111 - Y 99
o61
o62
PL1 Pulse Output
PL2 Pulse Output
No action 0
0
0
Y
Y
99
Set frequency 1
Actual frequency 2
Actual current 3
Output voltage 4
DC bus voltage 5
IGBT temperature 6
40

S
e
c
t
i
o
n

V

Output power 7
Output rpm 8
Actual torque 9
o63 SPA pulse output ratio 1~1000 1 Y 99
o64 SPB pulse output ratio 1~1000 1 Y 99
o65
o66
Limit time 1
configuration
Limit time 2
configuration
1 Bit
Boot time 0
0000
0000
Y
Y
100
Running timing 1
10Bit Reserved -
100Bit Reserved -
1000Bit Reserved -
o67 Limit Time 1 0.0~3200.0 2.0 Y 100
o68 Limit Time 2 0.0~3200.0 2.0 Y 100
5-1-6. Multi-speed PLC Group:H00-H55(0x0300-0x0337)
Factory
Setting
Change
Limited
Reference
page
H00 Multi-speed Collocation
1 bit
Program running
function cancel
0
0000 Y 100
Program running
function
1
10 bit
Direction decided by
H40~H46
0
Direction decised by
Terminal and
keyboard
1
100 bit
Deceleration and
acceleration time
decised by H26~H39
0
Time of acceleration
and deceleration
isdecided by terminal
1
1000 bit
Running time
decised by H18~H25
0
Running time
decised by terminal
1
H01
Program Running
Configuration
1 bit
sequence control 0
0710 Y 101
terminal control 1
10 bit
Program running
start segment
0~15
100 bit
Program running end
segment
0~15
1000 bit Output signal valid 0
41

S
e
c
t
i
o
n

V

time 8ms
Output signal valid
time 20ms
1
Output signal valid
time 100ms
2
Output signal valid
time 500ms
3
H02 Program Running Mode
1 bit
single-cycle 0
0000 Y 102
Continuous Cycle 1
One-cycle command
running
2
10 bit
The zero speed
running when pause
0
Fixed-speed running
when the suspension
1
100 bit
Stop with the
parameters set when
stop
0
Stop with the settings
of start up
1
1000 bit
Running at the speed
when start up
segment
0
before the machine
stopped
1
H03
1 Segment Speed
Setting 1X
Lower frequency ~ upper
frequency
3.00 Y 104
H04
2 Segment Speed
Setting 2X
frequency
6.00 Y 104
H05
3 Segment Speed
Setting 3X
frequency
9.00 Y 104
H06
4 Segment Speed
Setting 4X
frequency
12.00 Y 104
H07
5 Segment Speed
Setting 5X
frequency
15.00 Y 104
H08
6 Segment Speed
Setting 6X
frequency
18.00 Y 104
H09
7 Segment Speed
Setting 7X
frequency
21.00 Y 104
H10
8 Segment Speed
Setting 8X
frequency
24.00 Y 104
H11
9 Segment Speed
Setting 9X
frequency
27.00 Y 104
H12
10 Segment Speed
Setting 10X
frequency
30.00 Y 104
H13
11 Segment Speed
Setting 11X
frequency
33.00 Y 104
42

S
e
c
t
i
o
n

V

H14
12 Segment Speed
Setting 12X
frequency
36.00 Y 104
H15
13 Segment Speed
Setting 13X
frequency
39.00 Y 104
H16
14 Segment Speed
Setting 14X
frequency
42.00 Y 104
H17
15 Segment Speed
Setting 15X
frequency
45.00 Y 104
H18
0 Segment Running
Time T0
0.0~3200.0 2.0 Y 105
H19
1 Segment Running
Time T1
0.0~3200.0 2.0 Y 105
H20
2 Segment Running
Time T2
0.0~3200.0 2.0 Y 105
H21
3 Segment Running
Time T3
0.0~3200.0 2.0 Y 105
H22
4 Segment Running
Time T4
0.0~3200.0 2.0 Y 105
H23
5 Segment Running
Time T5
0.0~3200.0 2.0 Y 105
H24
6 Segment Running
Time T6
0.0~3200.0 2.0 Y 105
H25
7 Segment Running
Time T7
0.0~3200.0 2.0 Y 105
H26
1 Segment Acceleration
Time at1
0.0~3200.0 10.0 Y 105
H27
1 Segment Deceleration
Time dt1
0.0~3200.0 10.0 Y 105
H28
Time at2
0.0~3200.0 10.0 Y 105
H29
Time dt2
0.0~3200.0 10.0 Y 105
H30
Time at3
0.0~3200.0 10.0 Y 105
H31
Time dt3
0.0~3200.0 10.0 Y 105
H32
Time at4
0.0~3200.0 10.0 Y 106
H33
Time dt4
0.0~3200.0 10.0 Y 106
H34
Time at5
0.0~3200.0 10.0 Y 106
H35
Time dt5
0.0~3200.0 10.0 Y 106
H36
Time at6
0.0~3200.0 10.0 Y 106
H37
Time dt6
0.0~3200.0 10.0 Y 106
H38 7 Segment Acceleration 0.0~3200.0 10.0 Y 106
43

S
e
c
t
i
o
n

V

Time at7
H39
Time dt7
0.0~3200.0 10.0 Y 106
H40
H41
H42
H43
H44
H45
H46
1 Segment Speed
Configuration Word
2 Segment Speed
Configuration Word
3 Segment Speed
Configuration Word
4 Segment Speed
Configuration Word
5 Segment Speed
Configuration Word
6 Segment Speed
Configuration Word
7 Segment Speed
Configuration Word
1 bit
Running direction:
forward
0
0000
0000
0000
0000
0000
0000
0000
Y
Y
Y
Y
Y
Y
Y
106
Running direction:
reverse
1
10 bit
Running time:
*seconds
0
Running time:
*munites
1
Running time:
*hours
2
Running time: *days 3
100 bit
Acceleration time:
*seconds
0
Acceleration time:
*munites
1
Acceleration time:
*hours
2
Acceleration time:
*days
3
1000 bit
Deceleration time:
*seconds
0
Deceleration time:
*munites
1
Deceleration time:
*hours
2
Deceleration time:
*days
3
H47
0 Segment Digital
Voltage Giving
-100.0~100.0 0.0 Y 107
H48
1 Segment Digital
Voltage Giving
-100.0~100.0 10.0 Y 107
H49
2 Segment Digital
Voltage Giving
-100.0~100.0 20.0 Y 107
H50
3 Segment Digital
Voltage Giving
-100.0~100.0 30.0 Y 108
H51
4 Segment Digital
Voltage Giving
-100.0~100.0 40.0 Y 108
H52
5 Segment Digital
Voltage Giving
-100.0~100.0 50.0 Y 108
H53
6 Segment Digital
Voltage Giving
-100.0~100.0 60.0 Y 108
H54
7 Segment Digital
Voltage Giving
-100.0~100.0 70.0 Y 108
H55 Multi-speed Status 1 bit Current speed step 0~0 - N 108
44

S
e
c
t
i
o
n

V

xF
10 bit
Current acceleration
segment
0~0
x7
100 bit
Current running time
segment
0~0
x7
1000 bit
Current digit voltage
segment
0~0
x7
5-1-7. V/Fcurve Group:U00-U15(0x0400-0x040F)
Factory
Setting
Change
Limited
Reference
page
U00 V/ Setting Frequency1 0.00~U02 5.00 N 108
U01 V/F Setting Voltage 1 0~U03 10 N 108
U02 V/F Setting Frequency 2 U00~U04 10.00 N 109
U03 V/F Setting Voltage 2 U01~U05 20 N 109
U14 V/F Setting Frequency 8 U12~most frequency 40.00 N 109
U15 V/F Setting Voltage 8 U13~100 80 N 109
5-1-8. PID parameter:P00-P12(0x0500-0x050C)
Factory
Setting
Change
Limited
Reference
page
P00 PID Configuration
1 bit
Unidirectional
regulation
0
0000 N 109
Bidirectional
regulation
1
10 bit
Negative effect 0
Positive effect 1
100 bit
PID fault, N action 0
Warning &
Continuous running
1
Warning &
Decelerating stop
2
Warning & Free stop 3
1000 bit - -
45

S
e
c
t
i
o
n

V

- -
P01 PID Output Limit 0~100 100 Y 110
P02
Feedback Signal
Selection
Set frequency by keyboard or
RS485
0
1 Y 110
AI1 external analogy giving 1
Keyboard potentiometer
giving
4
muti-step digital voltage
giving
5
Digital pulse set 6
P03 Setting Signal Selection
RS485
0
2 Y 110
giving
4
Multi-step digital voltage
giving
5
Digital pulse set 6
P04 Keyboard Set Signal 0.0~100.0 50.0 Y 111
P05 PID integral time 0.002~10.000 0.250 Y 111
P06 PID Differencial Time 0.000~10.000 0.000 Y 111
P07 PID Proportion Gain 0~1000.0 100.0 Y 111
P08 PID Sampling Period 0.002~10.000 0.010 Y 112
P09 Deviation Limit 0.0~20.0 5.0 Y 112
P10 PID Fault Detect Time 0.0~3200.0 0.0 N 112
P11 PID Fault Detected Value 0.0~100.0 10.0 N 112
P12 PID Display Range 0.00~100.00 1.00 Y 112
5-1-9. Expanding parameters:E00-E23(0x0600-0x0617)
Factory
Setting
Change
Limited
Reference
page
E00 Load Type
General 0
0 N 112
Pump 1
Fan 2
Injection machine 3
Textile machine 4
Hoist machine 5
Kowtow Machine 6
46

S
e
c
t
i
o
n

V

belt conveyor 7
Variable frequency power 8
Multi-pumps constant pressure
water supply
9
Reserved 10
Reserved 11
Torque control 12
Voltage regulation power 13
Current regulation power 14
Extruding machine 15
E01
Starting Pressure
Deviation
0.0~100.0 10.0 Y 113
E02 Starting Delay Time 0.0~3200.0 5.0 Y 113
E03 Stop Frequency 0~50.00 5.00 N 113
E04 Stop Delay Time 0.0~3200.0 5.0 Y 113
E05
High Pressure Arrival
Value
0~100.0 90.0 Y 113
E06
Low Pressure Arribal
Value
0~100.0 10.0 Y 113
E07 Timing To Supply Water
1 bit
Timing
water
supply
invalid 0
0000 Y 113
Valid 1
10 bit
Pressure
giving
Set
according
to P03
0
Set
according to
H47~H54
1
100 bit
Timing
mode
Circle
mode
0
Single
circle
1
1000 bit Current timing step
E08
Timing Shift Alternation
Time
0.0~3200.0 0.0 N 114
E09
Electromagnetic Switch
Action Delay
0.000~10.000 0.500 Y 115
E10 Pumps Shift Judging Time 0~9999 5 Y 115
E11
Constant Pressure Water
Supply Configuration
1 bit
Stop
mode
all pumps
slow down
stop
0
0000 N 115
Variable
frequency
pump stop
1
Free stop 2
47

S
e
c
t
i
o
n

V

Water supply
Pump stop
3
10 bit
Pumps
status
when
fault
occurs
Keep current
situation
0
All-pumps stop 1
100 bit
Altern
ation
shift
mode
Variable
frequency to
working
frequency
0
Variable
frequency to
stop
1
1000 bit
Pump
status
keep
Keep status 0
Stop reset 1
E12
Multi-pumps
Configuration
1 bit
Pump 1 invalid 0
0001 N 117
Pump 1 variable
frequency to control
pump
1
Pump 1 soft starts to
control pump
2
10 bit
Pump 2 invalid 0
Pump 2 variable
pump
1
control pump
2
100 bit
Pump 3 invalid 0
Pump 3 variable
pump
1
control pump
2
1000 bit
Pump 4 invalid 0
Pump 4 variable
pump
1
control pump
2
E13 Multi-pumps Status
1 bit
Pump 1 stop 0
0000 N 117
Pump 1 run in
variable frequency
1
Pump 1 run in
working frequency
2
10 bit Pump 2 stop 0
48

S
e
c
t
i
o
n

V

Pump 2 run in
variable frequency
1
Pump 2 run in
working frequency
2
100 bit
Pump 3 stop 0
Pump 3 run in
variable frequency
1
Pump 3 run in
working frequency
2
1000 bit
Pump 4 stop 0
Pump 4 run in
variable frequency
1
Pump 4 run in
working frequency
2
E14
Soft Starting Pump
Control
1 bit
Pump 1 soft-no command 0
0000 Y 118
Pump 1 soft-stop 1
Pump 1 soft-start 2
10 bit
Pump 1 soft-no
command
0
Pump 2 soft-stop 1
Pump 2 soft-start 2
100 bit
Pump 1 soft-no
command
0
Pump 3 soft-stop 1
Pump 3 soft-start 2
1000 bit
Pump 1 soft-no
command
0
Pump 4 soft-stop 1
Pump 4 soft-start 2
E15 User Parameter 0 0~9999 0 Y 118
E18 User Parameter 3
0~9999
0 Y 118
E20 User parameter 5 0~9999 0 Y 118
0~9999
0 Y 118
0~9999
0 Y 118
5-1-10. Speed-loop parameter [SPD]:C00-C31(0x0700-0x071F)
Factory
Setting
Change
Limited
Reference
page
C00 Filter Time Of Speed-loop 2~200 10 Y 118
49

S
e
c
t
i
o
n

V

C01 Speed-loop Low Speed Ti 0.01~100.00 0.25 Y 118
C02 Speed-loop Low Speed Td 0.000~1.000 0.000 Y 118
C03 Speed-loop Low Speed P 0~150 100 Y 119
C04
Speed-loop Low Speed
Shift Frequency
0.0~C08 7.00 Y 119
C05 Speed Loop High Speed Ti 0.01~100.00 0.50 Y 119
C06
Speed Loop High Speed
Td
0.000~1.000 0.000 Y 119
C07 Speed Loop High Speed P 0~150 75 Y 119
C08
Speed Loop And
High-speed Switching
Frequency
C04~max frequency 30.00 Y 119
C09 Low-speed Slip Gain 0~200 100 Y 119
C10
Low Speed Slip
Switching Frequency
0~C12 5.00 Y 119
C11 High Speed Slip Gain 0~200 100 Y 119
C12
High Speed Slip
Switching Frequency
C10~ max frequency 30.00 Y 119
C13 Upper Froward Torque 0.0~300.0 250.0 Y 119
C14 Upper Reverse Torque 0.0~300.0 250.0 Y 120
C15
Forward
Torque setting
mode
1 bit
Setting
mode
Set by keyboard or
RS485
0
0000 Y 120
AI1 external analogy
giving
1
giving
2
giving
3
Keypad potentiometer
giving
4
Multi-step digital
voltage giving
5
Digital pulse set 6
10 bit direction
Direction uncontrolled 0
Direction controlled 1
C16
Reverse
Torque setting
mode
1 bit
Setting
mode
Set by keyboard or
RS485
0
0000 Y 120
AI1 external analogy 1
2
50

S
e
c
t
i
o
n

V

giving
giving
3
giving
4
Multi-step digital
voltage giving
5
Digital pulse set 6
10 bit direction
C17 Torque Set Gain 0.0~300.0 200.0 Y 121
C18
Speed /Torque Control
Shift
Speed control 0
0 Y 121
Torque control 1
C19
Upper speed
Setting mode
1 bit
Separate
setting
mode
keyboard or RS485
setting
0
0000 Y 121
AI1 external analog
setting
1
AI2 external analog
setting
2
AI3 external analog
setting
3
Keyboard
potentiometer setting
4
voltage setting
5
10 bit Selection
C19 Unit bit setting 0
S00 Setting Frequency 1
C20
Reverse Speed Limit
0.00~ Maximum frequency 50.00 Y 122
C21 Torque Acceleration Time 0.0~200.0 1.0 Y 122
C22
Torque Deceleration
Time
0.0~200.0 1.0 Y 122
C23
Low Speed Exitation
Excitation
0~100 30 Y 122
C24 Current Loop Ti 0~9999 500 Y 122
C25 Current Loop P 0~1000 100 Y 122
C26 PG Electronic Gear A 1~5000 1 Y 123
51

S
e
c
t
i
o
n

V

C27 PG Electronic Gear B 1~5000 1 Y 123
C28 PG Pulse 300~9999 2500 N 123
C29 Action When PG Break
N PG break protection 0
3 Y 123
Warning and keeping running 1
Warning and deceleration stop. 2
Warning and free stop. 3
C30 PG Rotating Direction
When motor forward, phase A
leads
0
0 Y 123
leads
1
C31
PG Dropped Inspection
Time
0.0~10.0 1.0 N 123
5-1-11. Motor parameter [MOT]:b00-b22(0x0800-0x0816)
Factory
Setting
Change
Limited
Reference
page
b00
Motor 1 Rated
Frequency
0.00~Maximum frequency 50.00 Y 123
b01 Motor 1 Rated Current y09*(50%~100%) Y
123
b02 Motor 1 Rated Voltage 100~1140
Y
123
b03 Motor 1 Pole-pairs 1~8 2 Y
123
b04 Motor 1 Rated Speed 500~5000 1480
Y
123
b05 Motor 1 N Load Current 0.0~b01 Y
124
b06
Motor 1 Stator
Resistance
0.000~30.000
Y
124
b07
Motor 1 Rotor
Resistance
0.000~30.000
Y
124
b08
Motor 1 Stator
Inductance
0.0~3200.0
Y
124
b09
Motor 1 Mutual
Inductance
0.0~3200.0
Y
124
b10 Motor Selection
Motor 1 0
0 N 124
Motor 2 1
b11
Motor Parameter
Measurement
No measurement 0
0 N 124
calculate by label data 1
inverter static measurement 2
inverter rotation measurement 3
b11
Motor Parameter
Measurement
No measurement 0
0 N 124
b12
Vector Control initial
Inspection R1
Not inspection R1 0
0 N 125
Inspection R1 1
52

S
e
c
t
i
o
n

V

b13 Motor 2 Rated Frequency 0.00~Maxmum frequency 50.00 Y 125
b14 Motor 2 Rated Current y09*(50%~100%) Y 125
b15 Motor 2 Rated Voltage 100~1140 Y 125
b16 Motor 2 Pole Pairs 1~8 2 Y 125
b17 Motor 2 Rated Speed 500~5000 1480 Y 125
b18 Motor 2 N Load Current 0.0~b14 Y 125
b19 Motor 2 Stator Resistance 0.000~30.000 Y 125
b20
Motor 2 Rotator
Resistance
0.000~30.000 Y 125
b21
Motor 2 Stator
Inductance
0.0~3200.0 Y 125
b22
Motor 2 Mutual
Inductance
0.0~3200.0 Y 125
5-1-12. System parameter [SYS]:y00-y17(0x0900-0x0911)
Factory
Setting
Change
Limited
Reference
page
y00 Reset System Parameter
No action 0
0 N 126
Reset system parameter with
keyboard storage1
1
keyboard storage 2
2
keyboard storage 3
3
keyboard storage 4
4
factory set value
5
y01
Parameter Upload To
Keyboard
No action 0
0 N 126
keyboard memory area1
1
2
3
4
Clear up keyboard memory
area 1, 2, 3, 4
5
y02 Lastest Fault record Lastest fault record number 0 Y 126
y03 Fault Record 1
Press [PRG]and [/] key the
frequency, crrent and running status
of fault time can be known.
0 Y 126
y04 Fault Record 2
y05 Fault Record 3
y06 Fault Record 4
y07 Fault Record 5
53

S
e
c
t
i
o
n

V

y08 Fault Record Reset
No action 0
0 Y 128
Reset 1
y09 Rated Output Current 0.1~1000.0 N 128
y10 Rated Input Voltage 100~1140 N 128
y11 Product Series
80 0 3
N 128
Family
code
Product
serial
Input
oltage
grade 1
y12 Software Version - - N 128
y13 Product Date-- Year YYYY - N 128
y14
Product Date
-Month/Day
MMDD - N 128
y15 User Decode Input
0~9999
Set
range
- Y 128
Record password
wrongly input times
Display
info
y16 User password key-in
0~9999
Set
range
- Y 129
No password or
decode input is
correct
code
Display
info
Parameter
lock-in
code
y17
Parameter Group
Protection
Corresponding parameter group
protection after set password
Set to 0: change is not allowed
Set to 1: change is allowed
0000 Y 129
54

S
e
c
t
i
o
n

V

5-2. Functional parameter specification
5-2-1. Menu Group
Code Description / LCD Function Discription Group ID
Refer
to page
S
Monitor Function
Group
Monitor frequency, current and other 16 monitor
objects
0B 54
F Basic Function Group
Frequency setting, control mode,accelerationtime
and deceleration time
00 55
A User Function Group Monitor, protection, communication setting 01 70
o IO Function Group Analog, digital input, output function 02 82
H
Multi-speed PLC
Group
Multi-speed running, PLCrunning 03 100
U V/F parameter Group User defined V/Fcurve 04 108
P PID Function Group Internal PID parameter setting 05 109
E Extend Function Froup
Constant pressure water supply and other functions
setting
06 112
C
Speed ring function
group
Current ring, speed running, PGparameter 07 118
b Motor parameter group Motor parameter setting 08 123
y System Function Group
Parameter reset, fault query, product information,
parameter protection
09 126
5-2-2. Monitor function:S00-S15(0x0B00-0x0B0F)
Code Description / LCD Setting Range Unit
Factory
Setting
Change
Limited
S00 Setting Frequency current inverter real setting frequency Hz - N
S01 Real Frequency current inverter real output frequency Hz - N
S02 Motor real Current Valid value of motor actual current A - N
S03
Percentage of Motor
Current
The percentage of actual motor curr -
ent and rated current
% - N
S04 DC Bus Voltage Detection value of DC bus voltage V - N
S05 The Output Voltage The real output voltage V - N
S06 Motor Real Speed Motor real running speed - - N
Under running, the real speed of the motor60*the real output frequency *Gain Speed surveillance
/pole of the motor .
Example: the real output frequency50.00Hz, Gain Speed surveillance A35=100.0%, the pole of the
motor b03/b162, the real speed of the motor1500rpm.
When stop, based Residual voltage test motor speed, renew speed 500ms.
The real speed 60*residual frequency*Gain Speed surveillance / the pole of the motor
Max display of motor real speed 9999rpm.
S07 Total Running Time The total running time for every time hour - N
When the ouptput, the frequency inverter calculated the running time.
Total running time can be cleared up automatically with A33 selecting reboot or continue accumu -
lation after reboot
55

S
e
c
t
i
o
n

V

Total running time of the units can be changed by parameter A34, you can choose hours or days as
the unit
S08 IGBT Temperature
Test the temperature of IGBT in the
frequency
- N
S09 PID Set Point
percentage of a given
% - N
S10 PID Feedback
percentage of feed back
% - N
S11
Motor Output
Frequency
The percentage of actual output power
of motor
% - N
The output frequency of the motorthe actual frequency of the motor *A36the regulate of the
motor frequency
Max display of the output frequency 2999.9
S12
Excitation Heft Set
Value
Motors set excitation heft percentage % - N
S13
Excitation Heft
Actual Value
Motors actual excitation heft percentage % - N
S14 Torque Heft Set Value Motor set torque percentage % - N
S15
Torque Heft Actual
Value
Motor actual torque hefts percentage % - N
5-2-3. Basic function Group:F00-F50(0x0000-0x0032)
Factory
Setting
Change
Limited
F00 Control Mode
V/Fcontrol 0
- 0 N
Sensorless vector control 1
Sensor feedback close loop
vector control
2
Control mode choose, setting 0~2.
0 : V/ Fcontrol
It is not sensitive to motor parameters, can be used as power supply; for motor control, using the
combination of vector control and V / F control strategies, appropriately adjusts motor parameters,
obtain high-performance control effect; suitable for a inverter driving a motor occasions; suitable
for a inverter driving multiple motors occasions; suitable for the inverter as a variable frequency
power supplies.
1 : Sensorless vector control
High-performance speed sensorless vector control; need to set the appropriate electrical parameters
or the motor parameter tuning; truly achieved the decoupled AC motor, so that operational control
of DC motors.
2 : Sensor feedback close loop vector control
Suitable for high precision speed control occasions, need to install PG card and pulse encoder shaft
in the motor or mechanical equipment.
F01
Keyboard Setting
Frequency
Lower frequency~upper frequency Hz 50.00 Y
The keyboard for a given operating frequency,it can be any frequency between lower frequency and
upper frequency .
F02/F03setting to 0, Involved in setting frequency calculation.
F02
Frequency Main Set
Mode
Keyboard setting frequency or
RS485
0 - 0 Y
56

S
e
c
t
i
o
n

V

Multi-segment digital voltage
setting
5
The main mode of the frequency running frequency:
0 : keyboard setting frequency or RS485 change F01 keyboard setting frequency
Multi-digital voltage terminal effective exchange, change F01keyboard setting value
1 : AI1 the external analog setting
Given the external analog0~10V,-10V~+10V,0~20mA.For detail please read the o group parameter.
Given the external analog 0~10V, 0~20mA. For detail please read the o group parameter.
4 : Keyboard potentiometer setting
Keyboard potentiometer setting, keyboard potentiometer for a given start and end values of the
corresponding values can be positive role and negative effects. For detail please read the A group
parameter.
5 : Multi-segment digital voltage setting
o36~o46 IO input terminal function set to 11, 12, 13, switch H47~H54 Multi-digital voltage
setting, 100% Corresponding to the maximum frequency .
6 : Digital pulse setting
Digital pulse input frequency Corresponding to the setting frequency, For detail please read the o52
group parameter.
Pulse input terminal and DI8 terminal reset, after using the digital pulse input,o43set to0,Otherwise,
the function settings will take effect, the pulse input on status of o58 can be checked, be limited to
low-speed pulse.
Through o36~o46 IO input teminal set to 14, 15, 16 be configured to switch the source
F03
Auxiliary Setting
Mode Of Frequency
Keyboard setting frequency or
RS485
0
- 0 Y
setting
4
Multi-segment digital voltage
setting
5
Digital Pulse Set 6
Auxiliary setting mode of frequency set:
0 : keyboard frequency setting frequency or RS485, change F01 kayboard setting frequency
After multi-digital voltage terminal effective switch, change F01keyboard setting.
Given the external analog0~10V,-10V~+10V,0~20mA.For detail please read the o group parameter.
Given the external analog 0~10V, 0~20mA.For detail please read the o group parameter.
57

S
e
c
t
i
o
n

V

Given the external analog 0~10V, 0~20mA.For detail please read the o group parameter.
4 : Keyboard potentiometer setting
Keyboard potentiometer setting, keyboard potentiometer for a given start and end values of the
corresponding values can be positive role and negative effects. For detail please read the A group
parameter.
5 : Multi-segment digital voltage setting
o36~o46 IO input terminal function set to 11, 12, 13, switch H47~H54 Multi-digital voltage
setting, 100% Corresponding to the maximum frequency .
6 : Digital pulse set
Digital pulse input frequency corresponding to set the frequency, For detail please read o52
parameter.
Pulse input terminal and DI8 terminal reseting, After use digital pulse input, o43set to 0,
Otherwise, the function settings will take effect, can check the pulse input status o58, be limited to
low-speed pulse.
7 : PID regulation mode
The completion of the main to the frequency of common analog feedback loop control. Speed
control accuracy requirements applicable to the general occasions.
The given value can be given through the keyboard can also be given through the analog.
Analog feedback can represent the pressure, flow, temperature.
Details see the P group of parameters.
The completion of the main to the frequency of common analog feedback loop control. Speed
control accuracy requirements applicable to the general occasions.
For a given value can be given through the keyboard can also be given through the analog.
Analog feedback can represent the pressure, flow, temperature.
Details see the P group of parameters.
Through o36~o46 IO input terminal, set to 17, 18, 19 be configured to switch the source for a given
ratio.
F04
The Relationship
Between Main And
Auxiliary Setting
Frequency
The main setting individual
control
0
- 0 Y
The auxiliary setting individual
control
1
main + auxiliary 2
main -auxiliary 3
(main *auxiliary)/maximum
frequency
4
Main given and auxiliary given set frequency relations:
Main given value and auxiliary given value can be added up, subtracted, multiplied, maximum,
minimum calculation.
O group parameters can be adjusted to coordinate the main given and auxiliary given proportion, to
meet the requirements of the system fine-tuning and bias.
58

S
e
c
t
i
o
n

V

F04
t
f
f
f
f
f
max
main
auxiliary
setting frequency
main
auxiliary
setting frequency f f
f
The relationship between main
give and auxiliary given
Main+Auxiliary
Main-Auxiliary
f
f
f
t
f
max
f
auxiliary
main
setting frequency

(Main*Auxiliary)/The Max Frequency
f
f
f
f
max
f
t
setting frequency
auxiliary
main

main
max
Maximum(Main&Auxiliary)
f
f
f
f
f
t
f
setting frequency
auxiliary

main
max
Manimum(Main&Auxiliary)
t
f
f
f
f
f
f
setting frequency
auxiliary

F05 Running Control Mode
Keyboard+Rs485/CAN 0
- 0 Y
Keyboard+terminal+Rs485/CAN 1
Rs485/CAN 2
Terminal control 3
The proportion linkage control 4
Stop and running command control mode
0 : keyboard+Rs485/CAN Control
1 : keyboard+Terminal+Rs485/CAN Control
control terminal, edge trigger, falling edge of the implementation of the Forward command FWD /
Reverse command REV, rising edge of the implementation of the STOP command
2 : Rs485/CAN Control
Under this function, only free stop funciont is valid under the keyboard control, other operation
control is invalid
3 : Terminal control, Level trigger.
Under this function, only free stop funciont is valid under the keyboard control, other operation
control is invalid
59

S
e
c
t
i
o
n

V

4 : The proportion linkage control
Select this function, the slave unit would execute the command from the proportion linkage host
unit.
Select this function, can also use keyboard, terminal, RS485 to control the proportion linkage slave
unit to run.
The proportion of linkage running,after stop the proportion linkage slave unit with the keyboard
terminal, Rs485, the slave unit will not run the proportion liknge host units command, it needs once
again to respond to host commands through the keyboard, terminal, RS485, or the proportion linkage
host sends stop command so that slave unit could respond to run commands.
F06 V/F Boost Mode
1 bit
Beeline V/Fcurve 0
- 0000 N
Power of 1.2
V/Fcurve
1
Power of 1.7 power
V/Fcurve
2
Power of 2
powerV/Fcurve
3
Define mode
V/Fcurve
4
10 bit
Close Automatic
torque boost
0
Automatic
torqueboost
1
100 bit
VF mode 0 Speed
No Output
0
VF mode keep 0
speed
1
1 Bit: V/F promote curve
0 Line V/F curve: Suitable for ordinary constant torque load
1 Power of 1.2 V/F curve: Appropriate torque down V/F curve, Suitable for liquid loads
2 Power of 1.7 V/F curve: Appropriate torque down V/F curve, Suitable for liquid loads
3 Power of 2 V/F curve: Torque down V/F curve, It is suitable for fans, pumps, centrifugal load
4 Define mode V/Fcurve: Can be customized appropriate curve according to the actual situation .
10 bit: Auto-torque boost mode
0 Close Automatic torque boost
1 Open automatic torque boost
parameters which affect automatic torque enhance :
Actual value torque component S15
b06/b19 stator resistance
F07 torque enhance value
Automatic torque enhance value = actual value of torque component * stator resistance *torque
enhance value.
100 bit: VF mode 0 speed maintain function
0 VF mode 0 Speed No Output: Output frequency is less than 0.5Hz, stop PWM output to reduce
the switching loss.
1 VF mode keep 0 speed: the output frequency is 0Hz, in accordance with the DC braking current
of starting F26, keep 0 speed.
F07 Torque boost Value 0.0~30.0% % 0.0 Y
F08
Torque Boost Cut-off
Frequency
0.00~Maximum frequency Hz 15.00 Y
60

S
e
c
t
i
o
n

V

Torque increase is mainly used to improve the low-frequency torque characteristics under sensorless
-V / F control mode.
Torque boost is too low, weak low speed motor
Torque boost is too high, motor over-excitation operation, large inverter output current, and low
efficiency.
The setting frequency of the inverter is lower than the frequency of the torque rising,the torque rising
will be valid;over than the setting frequency the torque rising will invalid.
Frequency Frequency
motor rated
voltage
Enhance
voltage
Basic frequency
Voltage
down the torque curve torque boost
Cut-off frequency
Constant torque curve torque boost
motor rated
voltage
Enhance
voltage
Basic frequency
Voltage
Cut-off frequency

F09 Accelerate Time 0.0~3200.0 s 10.0 Y
F10 Decelerate Time 0.0~3200.0 s 10.0 Y
F09 Accelerate time: accelerate time from 0Hz to maximum frequency.
F10 Decelerate time: decelerate time from maximum frequency to 0Hz.
F10 F09
Fmax
running time
Linear Acceleration

F11
Percentage Of Output
Voltage
50~110 % 100 Y
The percentage of the actual output voltage and the rated output voltage.
Used to adjust the output voltage,output voltageinverter rated output voltage*percentage of output
voltage.
F12 Maximum Frequency 10.00~320.00 Hz 50.00 N
Inverter output maximum frequency allowed is also the setting basis of acceleration / deceleration
time.
This parameter setting, you should consider characteristics of the motor speed and capacity.
F13 Lower Frequency 0.00~Upper frequency Hz 0.00 N
F14 Upper Frequency Lower frequency~Upper frequency Hz 50.00 N
F13 Lower frequency: the lower limit of the output frequency.
F14 Upper frequency: the uppper limit of output frequency.
When the frequency setting command is higher than the upper frequency, the operating frequency
will be the upper frequency;When the frequency setting command below the lower frequency,the
operating frequency is lower frequency. Start the motor that in the status of stopping, the inverter outputs
accelerate starting from 0Hz, accordance with the step 1 acceleration time towards the upper or the
setting frequency to accelerate. when motor Stop, the operating frequency decelerate according to
61

S
e
c
t
i
o
n

V

deceleration time down to 0Hz.
Fmax
0
upper limit frequency
lower limit frequency
frequency set signal 100

F15 Basic Frequency 5.00~Maximum frequency Hz 50.00 N
Corresponding to different fundamental frequency of the motor select this function. The basic V / F
characteristic curve is as below.
Fout
Un
base
frequency
maximum
frequency
Vout

F16 Carrier Frequency 1.0~16.0 kHz Y
This function is chiefly used to improve the possible noise and vibration during the operation of
frequency converter. When carrier frequency is higher, the output current has better wave, the torque is
great at lower frequency and the motor produces light noise. So it is very suitable for use in the
applications where great torque is output at low frequency quietly. But in these applications, the damage
to the switches of main components and the heat generated by the inverter are great, the efficiency is
decreased and the output capacity is reduced. At the same time, more serious radio interference is
resulted and special attention must be paid for application where very low EMI is needed, and filter
option can be used if necessary. Another problem for application of high carrier frequency is the increase
of capacitance-leakage current. The protector for leakage current may invalidate function, and over
current is also possibly caused.
When low carrier frequency is applied, the case is almost contrary to the above-mentioned one.
Different motor has different reflection to the carrier frequency. The best carrier frequency is gained
after regulation according to actual conditions. The higher the motor capacity is, the lower the carrier
frequency should be selected.
The company reserves the right to limit maximum carrier frequency as following:
The relation between carrier frequency and Motor Noise, Electric disturbance, Switch dissipation is
expressed as following:
Carrier
Frequency
Motor Noise Electric disturbance Switch dissipation
1.0KHz
Big

Small
Small

Big
Small

Big
8.0KHz
16.0KHz
The relationship of the carrier frequency and power :
62

S
e
c
t
i
o
n

V

Power(kW) 0.4-18.5 22-30 37-55 75-110 132-200 220
Carrier Frequency (Hz) 8.0K 7.0K 4.0K 3.6K 3.0K 2.5K
Note: Carrier frequency is bigger, the temperatuer of the machine is higher.
F17
Carrier Frequency
Adjustment Range
0.0~4.0 kHz 0.0 Y
F18
Carrier Frequency
Adjustment Mode
1 bit
No automatic
adjustment
0
- 00 Y
automatic adjustment
Mode
1
10 bit
Fixed mode
0
random mode
1
F17 Carrier frequency adjustment range
0.0~4.0kHz, Actual Carrier frequency adjustment range 1.0~16.0kHz
F18 Carrier frequency adjustment Mode
1 Bit: Carrier frequency automatic adjustment mode
0: No automatic adjustment
Carrier frequency according F16 to set .
1: automatic adjustment Mode
The carrier frequency automatically adjusts the model 10 can select random mode and fixed pattern.
10 Bit: Stochastic adjustment mode
0: automatic adjustment, Fixed mode
Load current>80% Carrier frequency =F16-F17
Load current<60% Carrier frequency =F16+F17
1: automatic adjustment, random mode
Load current >80% Carrier frequency = (F16-F17)~F16
Load current <60% Carrier frequency = F16~(F16+F17)
F19
Waveform Generation
Mode
Asynchronous space-vector
PWM
0
- 0 N
Stepless & subsection
synchronous space vector PWM
1
two-phase optimization space
vector PWM
2
PWM wave produce mode
0: Asynchronous space-vector PWM
1: Stepless & subsection synchronous space vector PWM
2: two-phase optimization space vector PWM
F20
The Acceleration Step
0.0~50.0 % 0.0 Y
F21
The Acceleration Atep
0.0~50.0 % 0.0 Y
F22
0.0~50.0 % 0.0 Y
F23
0.0~50.0 % 0.0 Y
1 indicat that the slope of the output frequency from 0 to the max.
63

S
e
c
t
i
o
n

V

2 indicat that the slope of the output frequency at constant segment.
3 indicat that the slope of the output frequency is reduced to 0 from the max.
Such as setting the S curve acceleration and deceleration, acceleration and deceleration time from
0Hz to the maximum frequency is calculated as follows:
Plus acceleration S characteristic time = F09 * F20
Constant extra acceleration S characteristic time = F09-(F09 * F20 + F09 * F21)
Minus acceleration S characteristic time = F09 * F21
Full acceleration time = F09 Acceleration time
Velocity S addition and subtraction characteristic time = F10 * F22
Constant deceleration S characteristics time = F10-(F10 * F22 + F10 * F23)
And reduction rate of S characteristic time = F10 * F23
All deceleration time = F10 deceleration time
F20 F21 F22 F23
1 1 2 3 2 3
F09 F10
Target frequency
running time
Current frequency
S curve acceleration&deceleration

F24
V/F Control Slip
Compensation
slip compensation invalid 0
- 0 N
slip compensation valid 1
Valid only under V/F control mode.
0 : Slip compensation function is invalid.
1 : Slip compensation function is valid.
Slip compensation value adjusted by the following parameters to ensure stable speed under load
fluctuations and heavy load,
C09 Low Slip Gain
C10 Low Slip switching frequency
C11 High-Speed Slip Gain
Slip C12 high-speed switching frequency
F25
Minimum Running
Frequency
0.00~maximum frequency Hz 0.00 N
Minimum frequency<lower frequency
Time
actual frequency
Time Time
Time
lower limit
frequency
set frequency
Minimum
frequency
lower limit
frequency
lower limit
frequency
lower limit
frequency
actual frequency
set frequency
Minimum frequency>lower frequency
Minimum
frequency
Minimum
frequency
Minimum
frequency

The set frequency lower than the minimum running frequency, the converter will stop, that is, when
the set frequency is less than the minimum running frequency, are determined that the set frequency is 0.
64

S
e
c
t
i
o
n

V

Minimum running frequency" and "lower frequency" relationship is as follows.
F26
DC Braking Current
When Starting
0~135 % 100 Y
F27
Braking Time When
Starting
0.0~60.0 s 0.0 Y
When frequency Inverter starting, the first injection of DC current, the current size is determined by
starting to set when the DC braking current and braking time, braking time from the start to set.
Value is based on inverter rated current as the benchmark, that is inverter rated current corresponds
to 100%. During setting process, be sure to gradually increase, until adequate braking torque, and can
not exceed the motor rated current.
start up braking
RUN
STOP
output
frequency
start up braking
ON
time

F28
Stop When The DC
Braking Current
0~135 % 100 Y
F29
Stop And Braking
Wait Time
0.0~60.0 s 0.0
Y
F30 Brake Time Stop 0.0~60.0 s 0.0
Y
F31
Stop And Brake
Starting Frequency
0.00~most frequency Hz 0.00 Y
Inverter slowing down to stop braking start frequency, stop the output PWM waveform to begin
injection of DC current, the current size by the shutdown of DC braking current setting, braking time,
braking time set by the downtime.
Value is based on inverter rated current as the benchmark, that is inverter rated current corresponds
to 100%. Setting process, be sure to gradually increase from a small, until adequate braking torque, and
can not exceed the motor rated current.
braking
frequency
time
time
Stop braking (RUNSTOP)
STOP
OFF
stop braking time
RUN
ON
setting
frequency
output
frequency
stop brake wait time

65

S
e
c
t
i
o
n

V

setting
frequency
forward
reverse
command
FOR REV
stop braking (forward and reverse rotate)
time
time
setting
frequency
output
frequency
braking
frequency
stop braking time

ON
setting
frequency
output
frequency
braking
frequency
RUN
STOP
braking
frequency
stop braking time
time
time
stop braking (run state)

F32 Stop Setting Mode
Deceleration stop 0
- 0 N
Free stop 1
When the frequency inverter receives the "stop" command, it will set the parameters accordingly to
this parameter to set the motor stop mode.
0 : deceleration to stop
Mode converter according to parameters set by the deceleration time to set the deceleration mode
to slow down to the lowest frequencies to stop.
1 : Free stop mode
Inverter receive "stop" command immediately stop output, according to the load inertia, motor
free-run to stop.
F33 Jog Acceleration Time 0.0~3200.0 s 1.0 N
F34 Jog Deceleration Time 0.0~3200.0 s 1.0 N
F35 Jog Mode Setting
1 bit
Jog direction: forward 0
- 000 N
Jog direction: reverse 1
Jog direction:
direction determined
by the main terminal
2
10 bit
Jog end mode: Stop
Running
0
Jog end mode:reset to
the former state before
jog
1
66

S
e
c
t
i
o
n

V

100 bit
deceleration time: reset
to the set acceleration
and deceleration time
before jog
0
deceleration time:save
the set acceleration and
deceleration time before
jog
1
F36 Jog Frequency Setting Lower frequency ~upper frequency Hz 6.00 Y
F34 F33
running time
Linear Acceleration
Fmax

Jog acceleration/deceleration time configuration defines the same section of acceleration / decele -
ration time.
The direction of jog is set by the unit bit of F35,when the Jog command does not contain the dire -
ction of jog, the direction of job will run as to the unit bit designated by F35. It is set to 2, the direction
of jog is run by the terminal or current direction.
The running status after jogging is identified by F35.
Whether jog acceleration/deceleration time is maintained through the confirmation on hundred bit
of F35 after jogging
F37 Skip Frequency1Limit 0.00~Maximum frequency Hz 0.00 Y
F38 Skip Frequency1Upper 0.00~Maximum frequency Hz 0.00 Y
During running, to skip resonance produced by the immanent resonance point in the machine sys -
tems, skip mode can do this.
At most three resonance points could be set to skip.
frequency setting signal
upper skip frequency 3
skip frequency 3
skip frequency 2
output frequency
skip frequency 1
lower skip frequency 1

67

S
e
c
t
i
o
n

V

Upper skip frequency and lower skip frequency define skip frequency range.
In the acceleration and deceleration process, inverter output frequency can normally through skip
frequency area.
F43 Preset Frequency 0.00~Max frequency Hz 0.00 Y
F44
Preset Frequency
Working Time
0.0~60.0 s 0.0 Y
After inverter startup, it firstly run with preset frequency, running time is preset frequency time,then
it will run with given frequency. Jog run will not be effective by preset frequency.
F45
Motor Running
Direction
1 bit
Direction command:
forward command
FWD let motor
forward running
0
- 0100 N
Direction command:
forward command
FWD let motor
reverse running
1
10 bit
Command prior:
terminal/keyboard
0
Prior command:
Analog given positive
and negative values
1
100 bit
Reverse allow:
reverse forbidden
0
Reverse allow:
reverse allow
1
1 : Bit: used to change the direction of motor running
0: Forward command FWD is to let motor forward running.
1: Forward command FWD is to let motor reverse running.
10 : Motor forward reverse running can be controled by the keyboard potentiometer and analog input
input positive or negative value.
0: Prior command:terminal / keyboard, set frequency can be negative value, but running direction
decided by terminal and keyboard command.
1: Prior command: positive or negative value of analog input, setting frequency positive value let
motor forward running, seting negative value let motor reverse running.
100:motor reverse allow. For some producing equipment, the reverse may lead to damage to the
equipment, so this feature can be used to prevent motor reverse, Inverter default forbidden reverse.
When the motor running direction opposes to equipment required direction, you can exchange the
wiring of any two inverter output terminals to let equipment forward running direction is consistent
with motor running.
0: reverse forbidden
1: reverse allow
F46 Pass 0 Stopping Time 0.0~60.0s s 0 N
Setting this parameter to achieve the motor forward to reverse (or from reverse running to forward),
the waiting time of motor speed being zero
68

S
e
c
t
i
o
n

V

F47
output
frequency
running time

F47
Frequency Multiple
Setting
*1 0
- 0 N
*10 1
0 : Set frequency display accuracy 0.01Hz
With this accuracy, F12 Maximum frequency setting range 10.00~320.00Hz.
1 : Set frequency display accuracy 0.1Hz
with this accuracy, F12 Maximum frequency setting range 100.0~800.0Hz.
After setting this parameter, there must be reset F12 maximun frequency.
F48
Acceleration And
Deceleration
Configuration Word
1 bit
N adjustment of
acceleration time
0
- 0000 N
1
2
3
4
Adjustment of Multi
giving
5
10 bit
N adjustment of
decceleration time
0
1
2
3
4
Adjustment of Multi
giving
5
100 bit
Acceleration time:*s 0
Acceleration time:*min 1
Acceleration time:*h 2
Acceleration time:*day 3
1000 bit Deceleration time:*s 0
69

S
e
c
t
i
o
n

V

Deceleration time:*min 1
Deceleration time:*h 2
Deceleration time:*day 3
1 bit: Acceleration time ajustment mode
0 No Adjustment Of Acceleration Time No adjustment
1
AI1 Adjustment Of The External
Analog Giving
Actual Acc. time=Acc. time*AI1 giving percentage
2
Analog Giving
Actual Acc. time = Acc. time*AI2 giving percentage
3
Analog Giving
Actual Acc. time = Acc. time*AI3 giving percentage
4
Adjustment Of Keyboard
Potentiometer Giving
Actual Acc.time = Acc. time*keyboard potentiometer
giving percentage
5
Adjustment Of Multi Steps Digital
Voltage Giving
Actual Acc.time=Acc.time*Multi steps digital voltage
giving percentage
10 bit: Deceleration time ajustment mode
0 No Adjustment Of Acceleration Time No adjustment
1
Analog Giving
Actual Acc.time =Dec. time*AI1 giving percentage
2
Analog Giving
Actual Acc.time = Dec. time *AI2 giving percentage
3
Analog Giving
Actual Acc.time = Dec. time *AI3 giving percentage
4
Adjustment Of Keyboard
Actual Acc.time = Dec. time*keyboard potentiometer
giving percentage
5
Adjustment Of Multi Steps Digital
Voltage
Actual Acc.time=Dec.time*Multi steps digital voltage
giving percentage
100, 1000 bit: The unit of Acc. and Dec time when program running on 0 step speed
Acc. and Dec. time 1000 bit 100 bit Range(e.g. F09, F10=3200.0)
*s 0 3200.0s
*Min 1 3200.0 Min
*H 2 3200.0 h
*Day 3 3200.0 Day

F49
Running Configuration
Word
1 bit
Running direction:
forward
0
- 0000 N
Running direction:
reverse
1
10 bit
Running time: *S 0
Running time: *Min 1
Running time: *H 2
Running time: *Day 3
70

S
e
c
t
i
o
n

V

Unit adjustment of actual running time.It is only valid on program running.
1 bit: Program running on multi-speed running period, Set bit to running direction of 0step speed.
Running driection Setting value
Forward 0
Reverse 1
When running control mode F050/1/2, control direction of 0 step speed.
When running control mode F053, Setting the value and terminal FWD / REV jointly decide the
direction of 0 step speed, FWD priority.
FWD=1running
direction
REV=1running
direction
Setting value
FWD REV 0
REW FWD 1
10 bit: unit of time running when on 0 step speed.
Running time 10 bit range(e.g. H18~H25=3200.0)
*S 0 3200.0s
*Min 1 3200.0Min
*H 2 3200.0H
*Day 3 3200.0 Day

F50
Energy Saving
Running Percentage
30~100 % 100 N
This parameter describes the minimum output voltage percentage of energy-saving operation. In the
constant speed operation, the inverter can be automatically calculated the best output voltage by the load
conditions.In the process of acceleration and deceleration is not to make such calculations.
Power-saving function is by lowering the output voltage and improve power factor to achieve the
purpose of saving energy, this parameter determines the minimum value of reducing of output
voltage;This parameter is set to 100%, then energy-saving function will take off.
When energy-saving function in effect, Actual output voltage value of inverter= The inverter rated
output voltage*The percentage of output voltage*output voltage percentage of energy saving operation.
frequency (Hz)
output voltatge (V)
100%
75%

5-2-4. User Function Group:A00-A55(0x0100-0x0137)
Factory
Setting
Change
Limited
A00
A01
A02
Monitor 1
Monitor 2
Monitor 3
Parameter group N: Parameter group N:
-
-
-
0B00
0B01
0B02
Y
Y
Y
X1000/X100 X10/ bit
00~0B 0~63(0x00~0x3F)

Code Keyboard display
Paramete
r group N
Function
spec
Parameter N(16
Hexadecimal Input)
S Monitor Function Group 0B S 0~16 (0x00~0x10)
71

S
e
c
t
i
o
n

V

F Basic Function Group 00 F 0~60 (0x00~0x3C)
A User Function Group 01 A 0~56 (0x00~0x38)
o IO Function Group 02 o 0~61 (0x00~0x3D)
H Multi-step Speed PLC Group 03 H 0~56 (0x00~0x38)
U V/F Curve Group 04 U 0~16 (0x00~0x10)
P PID Function Group 05 P 0~13 (0x00~0x0D)
E Extend Function Group 06 E 0~14 (0x00~0x0E)
C Speed Loop Parameter Group 07 C 0~32 (0x00~0x20)
b Motor Parameter Group 08 b 0~23 (0x00~0x17)
y System Function Group 09 y 0~18 (0x00~0x12)
That parameter N. should be 16 hex input.
Monitor1 will be valid when first power on, and which decide keyboard display content.
Such as:monitor 1 S01 actual frequency, A00=0x0B01.
Monitor 2 o57 DI1~4 terminal status, A01=0x0239.
Monitor 3 H55 multi-steps speed status, A02=0x0337.
A03
Over /Less Voltage
Stall Protection
N 0
- 1 Y
Y 1
A04
Overvoltage Stall
Protection Voltage
110%~140%( Standard bus voltage) % 120 Y
0 : This function invalid
1 : This function valid
When the inverter deceleration, as the motor load inertia, motor will produce feedback voltage to
inverter inside, which will increase DC bus voltage and surpass max voltage. When you choose Over
/less voltage stall protection and it is valid, Inverter detects DC side voltage, if the voltage is too high,
the inverter to stop deceleration (the output frequency remains unchanged), until the DC side voltage is
below the set value, the inverter will re-implement the deceleration
With braking models and external braking resistor, this function should be set to 0.
time
time
output frequency
DC voltage

A05 Auto Stablize Voltage
Invalid 0
- 0 Y Valid 1
Valid, usless for deceleration 2
CPU automatically detect the inverter DC bus voltage and to make real-time optimized processing,
when the grid voltage fluctuate, the output voltage fluctuation is very small,the V / F curve characteristic
has always been close to setting state of rated input voltage..
0 : function inalid.
1 : function Valid.
2 : function Valid, but useless for deceleration.
A06 Dynamic Braking option Invalid 0 - 0 Y
72

S
e
c
t
i
o
n

V

Security Type 1
General Type 2
A07 Hysteresis voltage 0~10% % 2 Y
A08
Dynamic Braking
Voltage
110%~140%( Standard bus voltage) % 130 Y
0 : Invalid
1 : Security Type
Only in the inverter deceleration process,and detected high-voltageDCbus exceeds a predetermined
value, the dynamic braking will be implemented
2 : general Type
under any state, when the inverter detected high-voltage DC bus exceeds a predetermined value, the
dynamic braking will be implemented.
When the inverter is running on emergency deceleration state or load great fluctuation, it may
appear over-voltage or over-current. This phenomenon is relatively prone to happen when the motor load
inertia is heavy.When inverterThe inverter internal DC bus detected voltage exceeds a certain value, the
output brake signal through an external braking resistor implement energy-braking function. Users can
select inverter models with a braking function to apply this feature.
A09 Less Voltage Level 60%~75%(Standard DC bus voltage) % 70 Y
The definition of allowed the lower limit voltage of normal working inverter DC side .For some
low power occasions, inverter less voltage value can be appropriately put down in order to ensure the
inverter normal working..
Under normal condition, keeping default setting.
A10
Power-down Tracking
Options
N 0
- 0 Y Power-off tracking mode 1
Startup tracking mode 2
A11
Power-down tTracking
Time
0.0~20.0 s 0.0 Y
start track state power down track state
speed search
frequency conversion
power frequency
power down
control
motor
rotate
speed
output
frequency
output
frequency
motor
rotate
speed
input
power
A11

This parameter is used to select the inverter tracking mode.
0 : N speed tracking means to start tracking from 0 Hz.
1 : power-down tracking
When the inverter instantaneous power off and re-start, the motor will continue running with
current speed and direction.
If the power off time is longer than A11 set time, the inverter will not re-start power on again.
2 : Startup tracking means that when power on, inverter will first inspect motor direction and speed,
and then driving motor with current speed and direction.
73

S
e
c
t
i
o
n

V

Set startup tracking function, power off tracking function is still valid.
A12
Drop Point
65~100%(standard DC bus voltage) % 75 Y
A13
Drop Time
0.1~3200.0 s 5.0 Y
Correctly setting this parameter can let inverter does not less voltage stop in case of instantaneous
power off.
When the DC bus voltage drop to frequency drop point A12 set, inverter will decelerate according
to deceleration time A13 set and stop outputting power to load. Meanwhile, inverter will use load
feedback energy to compensate DC bus voltage dropping and keep inverter working in short time.
Power down frequency drop time actually is deceleration time of frequency dropping after power
off.
If this value set is too large, the load feedback energy is small, then inverter can not compensate for
voltage dropping in DC.
if this value set is too small and there is large energy feedback from load, the excessive energy
compensation may cause inverter over-voltage fault.
Set A12 100% to cancel power off frequency dropping function.
A14 Current Limit
N 0
- 0 Y
Y 1
A15 Limit Fall Time 0.1~3200.0 s 10.0 Y
A16
Limit Deceleration
Protection Point
10~250 % Y
A17
Limit Fix-speed
Protection Point
10~250 % Y

Series Current limitaiton% Corresponding parameter
F
120 A17
130 A16
G
150 A17
170 A16
MTZ
170 A17
190 A16
H
250 A17
270 A16
Current limitation function can effectively restrain over-current caused by motor load fluctuation in
the process of acceleration and deceleration or constant speed operation.
This function will be good effect for V/F control mode.
Under protection of current lost- speed state, the motor speed will drop. so it is not adapted by
systme which is not allowed to automatically drop speed.
In operation process, when the motor current surpass value A16 set, motor will decelerate
according to deceleration time A15 set until current below value A16 set.
In operation process, when the motor surpass value A17 set, motor will run with this speed until
current below value A17 set.
Deceleration current limitation is prior of constant speed limitation.
A18
Output Phase Lose
Protection
N protection of phase lost 0
- 0 Y
Warning and constant running 1
74

S
e
c
t
i
o
n

V

Warning and deceleration 2
A19
Grade Of Phase Lose
Protection
10~100 % 30 Y
When ratio of unbalance 3phase output surpass A19 Grade of phase lose protection, the inverter
output phase lose protection i will action, and the system display fault PH-O.
Output frequency less than 2.00Hz, there is N output phase lose protection.
Phase lost protection grade=max current difference between phases, which will be according to
load condition.
A20
Over Torque Inspected
Action
N torque inspection 0
- 0 Y
A21 Over Torque Grade 10~250 % Y
A22
Over Torque Inspection
Time
0.0~60.0 s 0.1 Y
Motor output current surpass value A21 set, Over torque inspection will be force and the system
will show OL2 fault.
Series Over torque inspection class Parameter
F 130 A21
G 170 A21
MTZ 190 A21
H 270 A21

A23
Electronic Thermal
Relay Protection
Selection
N 0
- 1 Y
Y 1
A24
Electronic Thermal
Protection Grade
120~250 % Y
This function is to protect motor overheating when motor does not use thermal relay. Inverter using
some parameters to calculate motor temperature rise, at the same time to determine whether the use of
current caused motor overheat. When you choose electronic thermal protection function, the drive output
is shutdown after overheating detected also shows information of protection.
0 : No selecting this function
1 : Select this function.
Series electronic Thermal Protection Level Parameters
F 120 A24
G 150 A24
MTZ 170 A24
H 250 A24
A24 set the electronic thermal protection level . When the current is the rated motor current
multipleis the parameter, the drive in 1 minute protects, thermal protection within one minute that means
the actual current is A24 times of the rated current.
75

S
e
c
t
i
o
n

V

20min
0.2s
1min
5min
protect time
Ia A24

A25 Fault Reset Times 0~10 - 0 Y
In the inverter operation process, Over Current expressed by OCOver Voltage by OU, inverter can
automatically recover and run with state of preceding fault. Recovering times will be according to this
parameter. It can set 10 times at most. When this parameter is set 0, inverter will not automatically
recover after meeting fault. But if relay in DC main circuit meet fault MCC or less votage LU fault,
inverter will automatically recover without limitation.
Restarting from fault and normally running over 36s, inverter will automatically recover fault reset
times preset.
Restarting from fault and normally running over 36s, inverter will automatically recover to display
monitor parameter.
After 10 s of meeting fault, inverter will not recover fault reset function.
A26 Fault Reset Time 0.5~20.0 s 1.0 Y
Setting interval of fault reset time. When inverter met fault and stopped outputting, and when it
inspected without fault time is longer than fault reset time, Inverter will automatically implement fault
reset.
A27
Fan Startup
Temperature
0.0~60.0 0.0 Y
Set the fan start temperature.When the actual temperature of theS08is higher than the set temperature
the fan starts.
To avoid the the fan frequently starts and stops , the fan stop temperature = A27 fan start temperature
-1.0 .
A28
This Inverter
Communication Address
1~128 - 8 Y
This Inverter communication address: it is the only code to differentiate from other inverters.
Setting range 1~127 is slave inverter address, that can receive command and send out this
inverter state. Seeing attachment 1 for detailed specification.
The proportion of linkage function:
The proportion of linkage host inverter:
This inverter communcaiton address=128,
Communication interface A is set as host inverter communication interface for proportion of
linkage.
Communication interface B can be treated as keyboard interface or PC Host Computer Interface.
The proportion of linkage slave inverter:
This inverter communication address =1~127,
Communication interface A and B both can be set as communication interface of slave inverter for
the proportion of linkage.
Seeing appendix 2 for detailed specification.
A29 Baud Rate
Baud rate is 1200 0
- 4 Y Baud rate is 2400 1
Baud rate is 4800 2
76

S
e
c
t
i
o
n

V

Baud rate is 9600 3
The baud rate of communication port A can be set accordingly.
The baud rate of communication port B is fixed 19200bps.
A30 Communication Format
8, N, 1 for RTU 0
- 0 Y
8, N, 2 for RTU 1
8, E, 1 for RTU 2
8, O, 1 for RTU 3
8, E, 2 for RTU 4
8, O, 2 for RTU 5
Seeing attachment for detailed specification.
A31
Communications
Troubleshooting
N warning for communication
fault
0
- 0 Y
A32 Delay Inspection Time
0: N inspection
s 10 Y
1~250: late inpsection
When communication time between interface A or B surpassed A32 delayt inspection time, the
system will warn according to A31 setting.
After power on, interface without communication will not implement warning.
A33
Total Running Time
Setting
Auto clear to zero after power
on
0
- 1 Y
Continue to accumulate
running time after power on
1
To set whether the time of inverer running accumulating or not.
0 : Auto clear to 0 after power on.
1 : Continue to accumulate running time after power on.
A34
Unit Of Total Running
Time
hour 0
- 0 Y
Day 1
The set for unit of accumulation running time, only for display of running time.
0 : unit /hour display range 0~3200.0 hour.
1 : unit/day display range 0~3200.0 day.
A35
Motor Output Speed
Adjustment
0.1~1000.0 % 100.0 Y
Using for displaying adjustment of motor actual running speed.SeeingA00~A02 monitor options: 6:
motor actual running speed.
Setting 100%, corresponding display unit : rpm.
The max speed of displaying after adjustment is 9999.
A36
Adjustment Of Motor
Output Power
0.1~1000.0 % 100.0 Y
Used for displaying motor ouput power of adjustment. Seeing A00~A02 monitor options: 11 :motor
output power.
77

S
e
c
t
i
o
n

V

Setting 100%, corresponding display unit:%.
The max ouput power of displaying after adjustment is 2999.9.
A37
Keyboard Lock
Function Options
0~0FF - 0FF Y
Key SET+ESC in Keyboard can activate and cancel keyboard lock function.
To lock which key will be decided by corresponding parameter :
Potentiometer
7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2
0 1 2 3 4 5 6 7
FWD
STOP
PRG
SET
ESC
MF1
MF2

Set 0~10 bit Keyboard locked state
0
0 Unlock FWD key
1 Lock FWD key
1
0 Unlock STOP key
1 Lock STOP key
2
0 Unlock PRG key
1 Lock PRG key
3
0 unlock SET key
1 Lock SET key
4
0 Unlock ESC key
1 Lock ESC key
5
0 Unlock MF1 key
1 Lock MF1 key
6
0 Unlock MF2 key
1 Lock MF2 key
7
0 Unlock potentiometer
1 Lock potentiometer
A38 UP/DN Control
1 bit
Power down to save 0
- 0000 Y
Power down to clear
saving
1
10 bit
saving after stopping 0
Stop command to
clear saving
1
Cleared at the end of
stopping
2
100 bit
One-direction
adjustment
0
Double-direction
adjustment
1
1000 bit
Invalide adjustment 0
Valide adjustment 1
78

S
e
c
t
i
o
n

V

1 bit: UP/DN control saving state after power down
0: power down to save
1: power down to clear
10 bit: UP/DN control saving after stopping
0: Keeping afer stopping
1: Stop command to clear saving
2: Cleared at the end of stopping
100 bit: UP/DN control direction of adjustment.
0: one direction adjustment, it is one direction adjustment within 0~max frequency range.
1: double direction adjusment, it is FEW and REW adjustment within 0~max frequency range.
1000 bit: UP/DN control validity of adjustment.
0: UP/DN invalid ajustment
1 : UP/DN valid adjustment
A39 UP/DN Time
1 bit
UP fix speed 0
- 0000 N
UP fix times 1
10 bit
DN fix speed 0
DN fix times 1
100 bit
UP N adjustmentof
speed ratio
0
1
2
3
adjustment of
4
Adjustment of multi
5
1000 bit
DN N adjustmentof
speed ratio
0
1
2
3
adjustment of
4
Adjustment of multi
5
1 bit: UP acceleration mode
0: fix speed acceleration, according to A41 fix speed: To increase frequency every 200ms.
1: fix times acceleration, according to fix times: To increase frequency every triggering.
10 bit: DN deceleration mode
0: fix speed deceleration, according to A42 fix speed: To reduce frequency every 200ms.
1: fix times deceleration, according to A42 fix times: To reduce frequency every triggering.
100 bit: UP adjustment mode of adjusting speed ratio
79

S
e
c
t
i
o
n

V

0
UP N Adjustment Of
Speed Ratio
N adjustment
1
AI1 Adjustment Of The
External Analog Giving
Actual UP adjustment ratio= percentage given by A41*AI1
2
Actua UP adjustment ratio= percentage given by A41*AI2
3
Actual UP adjustment ratio= percentage given by A41*AI3
4
Adjustment Of
Actual UP adjustment ratio= percentage given by A41*
potentiometer
5
Adjustment Of Multi-steps
Digital Voltage
Actual UP adjustment ratio=percentage given by A41*
multi-steps digital voltage
1000 bit: DN adjustment mode of adjusting speed ratio
0
N Adjustment Of
Acceleration Time
N adjustment
1
Actual DN adjustment ratio =percentage given by A42*AI1
2
Actual DN adjustment ratio =percentage given by A42*AI2
3
Actual DN adjustment ratio=percentage given by A42*AI3.
4
Adjustment Of
Actual DN adjustment ratio=percentage given by
A42*potentiometer
5
Adjustment Of Multi-steps
Digital Voltage
Actual DN adjustment ratio=percentage given by
A42*multi-steps digital voltge.
A40
UP/DN Adjustment
Value
-300.00~300.00 - 0.00 N
Frequency after adjustmentset frequency+UP/DN adjustment value.
A41 UP Adjustment Ratio 0.01~20.00 Hz 0.01 Y
Fix speed: To increase frequency every 200ms.
Fix times: To increase frequency every triggering.
A42 DN Adjustment Ratio 0.01~20.00 Hz 0.01 Y
Fix speed: To reduce frequency every 200ms.
Fix times: To reduce frequency every triggering.
A43
A44
The Definition Of
Multifunction Keys
MF1 And MF2
MF is defined as adding
function key
0
-
-
0
1
Y
Y
MF is definded as reducing
function key
1
MF is defined as free stopping
key
2
MF is defined as FWD running
key
3
MF is defined as REV running
key
4
MF is defined as forward JOG
function key.
5
80

S
e
c
t
i
o
n

V

MF is defined as reverse JOG
function key.
6
MF is defined as JOG function
key.
7
MF is defined as UP function key 8
MF is defined as Down function
key.
9
UP / DN adjusted value reset 10
keyboard potentiometer
setting value resey
11
The user defined keyboard can define MF key functions.
0 : MF is defined as adding function key:
Under monitor menu, adding function key MF can adding revise frequency F01 set.
Under parameter choosing menu, adding function key MF can adjust parameter choice.
Under parameter revising menu, adding function key MF can adjust parameter value.
1 : MF is defined as reducing function key:
Under monitor menu, reducing function key MFcan reducing revise frequency F01 set
Under parameter choosing menu, reducing function key MF can adjust parameter choice.
Under parameter revising menu, reducing function key MF can adjust parameter value.
2 : MF is defined as free stopping key:
MF key is valid under monitor menu and select parameter menu, inverter will be free stopping. After
free stop, no start command, 1 S later, allow running again..
3 : MF is defined as FWD running key:
Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be
forward running.
4 : MF is defined as REV running key:
Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be reverse
running.
5 : MF is defined as forward JOG function key:
Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be
forward JOG running.
6 : MF is defined as reverse JOG function key:
Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be reverse
JOG running.
7 : MF is defined as JOG function key:
Pressing MF key is valid under monitor menu and parameter choosing menu, inverter will be JOG
running. Running direction decided by F35 bit setting and terminal state.
8 : MF is defined as UP function key:
Pressing MF is always valid, inverter will be UP control, control parameter decided by A38~A42.
9 : MF is defined as Down function key:
Pressing MF is always valid, inverter will be DOWN control, control parameter decided by
A38~A42.
10MF is defined as the UP / DN adjusted value resetA40 UP / DN adjusted value reset, level-triggered.
11 : MF is defined as the setting value of potentiometer on the keyboard A47 keyboard potentiometer
setting is reset, level-triggered
A45
Keyboard
Potentiometer X1
0~100.0 % 0.0 Y
The start point of value keyboard potentiometer set.
A46 Keyboard 0~100.0 % 100.0 Y
81

S
e
c
t
i
o
n

V

PotentiometerX2
The end point of value keyboard potentiometer set.
A47
The Value Of Keyboard
Potentiometer Set
0.0~100.00 % - Y
Displaying value potentiometer set, which can be revised by potentiometer under monitor menu.
Value potentiometer set can be regarded as analog of frequency giving , set value = max frequency
*keyboard potentiometer set value.
Potentionmeter set value can be regarded as value of PID giving,value of PID giving=keybaord
potentiometer set value.
A48
Keyboard Potentiometer
X1 Corresponding Value
Y1
-100.0~100.0 % 0.00 Y
A49
Keyboard Potentiometer
X2 Corresponding Value
Y2
-100.0~100.0 % 100.00 Y
end point start point
Start point
corresponding
value
End point
corresponding
value
end point start point
Start point
corresponding
value
End point
corresponding
value

A50
Keyboad
Potentiometer Control
1 bit
Saving after power
down
0
- 0000 Y
Cleared after power
down
1
10 bit
Saving after stoppoing 0
Clear saving after
stopping command
1
Clear saving at end of
stopping
2
100 bit Reserved
1000 bit Reserved
1 bit: Saving state of potentiometer after power down.
0: Saving after power down.
1: Clearing saving after power down.
10 bit: keeping potentiometer set after stopping.
0: keeping after stopping
1: To clear saving after stop command.
2: To cear saving at end of stopping.
A51
Temperature
Adjustment Of Motor
0.0~200.0 % 100.0 N
Being used to revise displaying of A54 motor temperature.
A52
Over-heat Temperature
Of Motor
0.0~300.0 120.0 N
82

S
e
c
t
i
o
n

V

A53
Reaction For Motor
Over-heat
N reaction for motor over-heat 0
- 0 Y
Warning and runing 1
Warning and deceleration
stopping
2
When the displaying value of motor temperature A5 surpassed value A52, inverter will warn and
react according to reaction for motor over-heat A53 set.
A54
Display Of Motor
Temperature
-50.0~300.0 - N
Shows the motor temperature or temperature at other point.
Control card PT100 plug should plug into the optional PT100 thermocouple devices
Three lines PT100

A55
Proportion Of Linkage
Ratio
0.10~10.00 - 1.00 Y
In application of proportion of linkage, A55 setting is multiply ratio of that when slave inverter
received setting frequency command from host inverter.
Setting this inverter as one slave inverter of system for proportion of linkage.
Frequency Keyboard F01 setproportion of linkage ratio* frequency S00 set by host inverter
5-2-5. IO function group:o00-o68(0x0200-0x0244)
Factory
Setting
Change
Limited
o00 AI1 Input X1 0~100.0 % 0.0 Y
o01 AI1 Input X2 0~100.0 % 100.0 Y
o02 AI2 Input X1 0~100.0 % 0.0 Y
o03 AI2 Input X2 0~100.0 % 100.0 Y
o04 AI3 Input X1 0~100.0 % 0.0 Y
o05 AI3 Input X2 0~100.0 % 100.0 Y
o06
AI1 Input X1
-100.0~100.0 % 0.0 Y
o07
AI1 Input X2
-100.0~100.0 % 100.0 Y
o08
AI2 Input X1
-100.0~100.0 % 0.0 Y
o09
AI2 Input X2
-100.0~100.0 % 100.0 Y
o10
AI3 Input X1
-100.0~100.0 % 0.0 Y
o11
AI3 Input X2
-100.0~100.0 % 100.0 Y
Under the situation Max frequency50.00hz:
83

S
e
c
t
i
o
n

V

Y2=100%
X2=100% X1=0%
Y1=0%
AI1,AI2,AI3
x
y
(X1,Y1)

X1=0%,Y10% potentiometer 0V corresponding set frequency:f=Max frequency*Y1=0.00Hz
X2=100%,Y2100% potentiometer10Vcorresponding set frequency:f=Maxfrequency*Y2=50.00Hz
y
x
AI1,AI2,AI3
Y1=0%
X1=20%
X2=50%
100%
Y2=50%
(X2,Y2)
80% 100%
10V
(X1,Y1)

X1=20%, Y10% potentiometer 2V corresponding set frequency: f=Max frequency*Y1=0.00Hz
X2=50%, Y250% potentiometer 5V corresponding set frequency: f=Max frequency*Y2=25.00Hz
10V
100%
80%
(X2,Y2)
Y2=50%
100%
X2=50% X1=0%
(X1,Y1)
AI1,AI2,AI3
x
y
Y1=20%

X1=0% , Y120% potentiometer 0V corresponding set value: f=Max frequency*Y1=10.00Hz
X2=50%, Y250% potentiometer 5V corresponding set value: f=Max frequency*Y2=25.00Hz
y
x
AI1,AI2,AI3
Y1=-100%
X1=0%
X2=100%
100%
Y2=100%
(X2,Y2)
100%
10V
(X1,Y1)
5V
50%

X1=0%,Y1-100% potentiometer 0V corresponding set frequency:f=Max frequency*Y1=-50.00Hz
X2=100%,Y2=100%potentiometer 10V correspond set frequency:f=maximum frequency*Y2=50.00Hz
84

S
e
c
t
i
o
n

V

Skipping thread of AI1, AI2, AI3 respectively are JP3/JP5, JP6, JP7, seeing the following detailed
specification:

o12 AI1 Input Filter Time 0.00~2.00 s 0.10 Y
Filter time constant of analog signal input, that is 0.00~2.00s.If time parameter is set too long, the
changement of setting frequency will be stable, but responsing speed will be slow;If time parameter is
set too short, the changement of setting frequency will not be stable, but responsing speed will be quick.
o15
o16
DA1 Output Terminal
DA2 Output Terminal
N reaction 0
-
-
-
-
Y
Y
Setting frequency 1
Actual frequency 2
Actual current 3
Output voltage 4
DC bus voltge 5
IGBT temperature 6
Output power 7
Output RPM 8
Actual value of torque 9
o17
DA1 Adjustment Of
Lower Limit Output
0.0~100.0 % 0.0 Y
o18
DA1 Adjustment Of
Upper Limit Of Output
0.0~100.0 % 100.0 Y
o19
DA2 Adjustment Of
Lower Limit Output
0.0~100.0 % 0.0 Y
o20
DA2 Adjustment Of
Upper Limit Output
0.0~100.0 % 100.0 Y

Output Content Setting Value Giving Output Singla Range
N Reaction 0 N output
Setting
Frequency
1 0~Max frequency
Actual
Frequency
2 0~Max frequency
Actual Current 3
0~200%, corresponding parameter: S03 percentage
of output curent
Output Voltage 4
0~200%, corresponding parameter: b02b15 rate
voltage of motor
DC Bus Voltage 5 0~1000VDC, DC voltage
IGBT
Temperature
6 0~100.0
85

S
e
c
t
i
o
n

V

Output Power 7 0~200%
Output RPM 8 0~Max RPM
Actual Value Of
Torque
9 0~200% torque
10V/20mA
10.0% 20.0%
the corresponded
output frequency
0V/0mA
50.0% 100.0%
0Hz
Voltage/Current
DA1
DA2

This parameter is used for setting upper/lower limitation of DA1/DA2 output signal.
Such as:
If DA1 output 1~5V voltage, setting parameter as: o1710.0%, o1850.0%
If DA2 output 4~20mA current, setting parameter as: o1920.0%, o20100.0%
DA1, DA2 Skipping thread:

Caution: Every terminal has choice of voltage output and current output, the default setting is voltage
output. When the voltage output is needed, please connect JP1/JP2 and DA1V/DA2V(seeing the panel);
When the current output is needed, please connect JP1/JP2 and DA1C/DA2C.
o21
o22
o23
o24
O1 Output Signal
Option1
O2 Output Signal
Option 2
O3 Output Signal
Option 3
O4 Output Signal
Option 4
No function 0
-
-
-
-
0
0
1
8
Y
Y
Y
Y
Fault warning 1
Over current inspection 2
Over load inspection 3
Over voltage inspection 4
Less voltage inspection 5
Low load inspection 6
Over heat inspection 7
Running state with command 8
Abnormal PID feedback signal 9
Motor state of REW running 10
Arrival of setting the frequency 11
Arrival of Upper frequency 12
Arrival of Lower frequency 13
frequency 1
14
frequency 2
15
86

S
e
c
t
i
o
n

V

FDT frequency level inspection 16
Arrival of preset counter value 17
Arrival of upper limit counter 18
Program running one period
completed
19
Speed tricking mode inspecition 20
No command running state 21
REV running from inverter
command
22
Deceleration running 23
Acceleration running 24
Arrival of high pressure 25
Arrival of low pressure 26
Arrival of inverter rate current 27
Arrival of motor rate current 28
Arrival of input frequency
lower limitation
29
Arrival of current upper
limitation
30
Arrival of current lower
limitation
31
Inverter ready to run 34

Setting
Value
Output Content Specification Explaination
0 No Function
Setting 0, N output reaction, but inverter can be controlled
by theoretical terminal.
1 Fault Warning Inverter at fault or after fault with unconfirmed status.
2 Over Current Inspeciton Inverter met fault of over current
3 Over Load Inspeciton Inverter met fault of over load of heat protection
4 Over Voltage Inspeciton Inverter met fault of over voltage
5 Less Voltage Inspeciton Inverter met fault of less voltge
6 Lower Load Inspection Inverter met fault of lower load
7 Over Heat Inspeciton Inverter met fault of over heat.
8 Running State Of Command Inverter is under running state of command
9 Abnormal PID Feedback Signal PID feedback signal is abnormal
10 Motor State Of REW Running Motor is reverse running
11 Arrival Of Setting Frequency Arrive at set frequency
12 Arrival Of Upper Frequency Arrive at upper frequency
13 Arrival of lower frequency Arrive at lower frequency
87

S
e
c
t
i
o
n

V

14 Arrival Of FDT Set Frequency1 Arrive at frequency 1 FDT set
15 Arrival Of FDT Set Frequency2 Arrive at frequency 2 FDT set
16
Inspection Level Of FDT
Frequency
FDT frequency levels to meet the inspection conditions,o29~
o31
17
Arrival Of Preset Counting
Value
Present counting value arrives at preset counting value
18
Arrival Of Counting Value
Upper Limitation
Present counting value arrives at upper limitation of counting
value.
19
Program Ruuning One Period
Completion
Program runs one period to complete.
20 Inspection In Speed Trick Mode Inverter is under speed trick state, the valid time is A11
21 No Command Running State Inverter is under N command running state
22 REW Command Of Inverter Inverter is under reverse running command
23 Deceleration Running Inverter is under deceleration running
24 Acceleration Running Inverter is under acceleration running
25 Arrival Of High Pressure Arrival at hight pressure
26 Arrival Of Low Pressure Arrival at low pressure
27 Arrival Of Inverter Rate Current Arrival at inverter rate current
28 Arrival Of Motor Rate Current Arrival at motor rate current
29
Arrival Of Input Frequency
Lower Limitation
Present set frequency is less than frequency lower limitation
30
Arrival Of Current Upper
Limitation
Arrive at current of upper limitation
31
Arrival Of Current Lower
Limitation
Arrive at current of lower limitation
32 Time to reach limit time 1 Timing action mode refer to o65 configuration
33 Time to reach limit time 2 Timing action mode refer to o66 configuration
34 Inverter ready to run
The end of initialization when the drive power on , running
command is acceptable.

s 0 Y
o26 Output Signal Delay 2 0~32.000 s 0 Y
s 0 Y
s 0 Y
o25~o28 defines o21~o24 output signal reaction delay time, unit is S.
Output signal cut off action without delay.
o29 FDT Set Frequency 1 o30~Max frequecy Hz 0.00 Y
o30 FDT Set Frequency 2 0~o29 Hz 0.00 Y
o31 FDT Inspection Range 0.00~5.00 Hz 0.00 Y
When the choice of output signal(o21~o24)is set as14, inverter output frequency arrives at or
surpass FDT set frequency 1, the corresponding signal output terminal will react; When inverter output
frequency is below of frequency 1 FDT set, the corresponding signal output terminal will not react.
When the output signal options(o21~o24)is set as 15, inverter output frequency reaches or surpass
88

S
e
c
t
i
o
n

V

FDT set frequency 2, the corresponding signal output terminal will react;When inverter output frequency
is below of frequency 3 FDT set, the corresponding signal output terminal will not react.
When the output signal options (o21~o24)is set as16, inverter will firstly inspect FDT set freuqnecy
1, then inverter output frequency arrives at or surpass FDT set frequency 1, the corresponding signal
output terminal will react;After terminal reaction, inverter will inspect FDT set frequency 2, When
inverter output frequency is below of frequency 2 FDT set, the corresponding signal output terminal will
not react.
o31 frequency inspection range
This parameter is used to define inspection range. When the difference of actual frequency and
inspected frequency has surpassed inspection range, terminal will output react.
e.g.: FDT set frequency 1 as 35Hz, FDT set frequency 2 as 30Hz,
Frequency inspection range is 0, the signal output terminal will react as below:
OFF
OFF OFF
OFF ON
ON ON
ON
time
time
time
output frequency
FDT frequency
setting 1 arrived
FDT1=35Hz
FDT2=30Hz
FDT frequency
setting 2 arrived
ON means signal will react, OFF means signal will not react
OFF ON OFF ON
FDT frequency
inspection level
time

o32
Arrival Of Current
Upper Limitation
o33~200% % 120 Y
o33
Arrival Of Current
Lower Limitation
o34~o32 % 20 Y
o34
Current Inspection
Range
0~o33 % 3 Y
current lower limitation
time
time
time
ON means signal will react, OFF means signal will not react
o32=120
o33=20
o34=3
current percentage
current upper limitation
20
120
ON OFF ON OFF
OFF ON OFF
o34 o34 o34 o34
OFF
o34 o34

When the output signal options (o21~o24)is set as 30, and inverter output current reach or surpass
o32+o34, the corresponding output signal terminal will react. When the inverter output current is less
than o32-o34, The corresponding output signal terminal will not react.
89

S
e
c
t
i
o
n

V

When the output signal options (o21~o24)is set as 31, and inverter output frequency reach or less
than o33-o34, the corresponding output signal terminal will react;When the inverter output current is
more than o33+o34, The corresponding output signal terminal will not react.
o34 is used to define current inspection range. When the difference of actual current and inspected
current has surpassed inspection range, The output terminal will react.
o35 Terminal Control Mode
bit
Two-wire running
control 1
0
- 0000 N
Two-wire running
control 2
1
Three-wire running
control 1
2
Three-wire running
control 2
3
One-shot operation
control 1
4
One-shot operation
control 2
5
10 bit
Terminal command
is invalid after power
on running
0
Terminal command
is valid after power
on running
1
Setting terminal running mode by this parameter.
1 Bit set terminal running mode:
The polarity of electrical level is o47 default setting polarity. Low electrical level or falling edge
is valid, and the terminal is leakage-souce driving mode.
X can be used to express high or low electrical level, rising or falling edge.
Running Control Mode
Keyboard Running
Control
Prior Running Prior Direction
Edge Trigger Valid Same Same
E-level Trigger Invalid Prior running Prior FWD
0: Two wire running control 1
FWD/ STOP
REV/ STOP
COM
REV
FWD

F05=1 or F05=4 F05=3
Command
FWD REV FWD REV
lling edge X Low E Level X FWD running
X Falling edge High E-level Low E-level REV running
Rising edge Rising edge High E-level High E-level STOP running
1: Two wire running control 2
90

S
e
c
t
i
o
n

V

FWD
REV
COM
FWD/ REV
RUN/ STOP

F05=1 or F05=4 F05=3
Command
FWD REV FWD REV
Falling edge Falling edge Low e-level Low e-level FWD running
Falling edge Rising edge Low e-level High e-level REV running
Rising edge X High e-level X STOP running
2: Three wire running control 1
FWD
STOP
COM
STOP
RUN
REV
FWD/REV

F05=1 ;F05=3; F05=4
Command
FWD REV STOP
Falling edge Low e-level Low e-level FWD running
Falling edge High e-level Low e-level REV running
X X High e-level STOP running
3: Three wire running control 2
REV
REV
FWD
STOP
COM
STOP
FWD

F05=1 ;F05=3; F05=4
Command
FWD REV STOP
Falling edge X Low e-level FWD running
X Falling edge Low e-level REV running
X X High e-level STOP running
4: One-shot operation control 1
COM
REV
FWD
FWD/ STOP
REV/ STOP

F05=1F05=4F05=3
Command Current state
FWD REV
X FWD running STOP running
91

S
e
c
t
i
o
n

V

Keep REV running STOP running
X STOP running FWD running
Keep REV running FWD running
X FWD running REV running
Keep STOP running REV running
5: One-shot operation control 2
FWD
REV
COM
FWD/ REV
RUN/ STOP

F05=1F05=4F05=3
Command Current state
FWD REV
Low e-level FWD running STOP running
High e-level REV running STOP running
X STOP running FWD running
X STOP running REV running
10 bit: Set the terminal status when power on
0: Terminal run command invalid when Power on.
Terminal run command invalid when power on,. Only run 3S later after power on and set terminals
invalid.
1: Terminal run command valid when Power on.
Terminal status is effective when power on, inverter will run immediately, in some cases such status
will not be allowable.
o36
o37
o38
o39
o40
o41
o42
o43
o44
o45
o46
Function Selection
Function Selection
(DI3 )Input Terminal
Function Selection
Function Selection
Function Selection
Function Selection
Function Selection
Function Selection
Function Selection
Function Selection
No function 0
-
-
-
-
-
-
-
-
-
-
-
0
0
0
0
0
0
0
0
0
0
0
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Forward running FWD 1
Reverse running REV 2
3-line mode running STOP 3
Multi-segment command 7
Multi-segment speed command 9
frequency
14
The main set mode 2 of set 15
92

S
e
c
t
i
o
n

V

Function Selection frequency
frequency
16
The auxiliary setting mode 1 of
frequency set
17
frequency set
18
frequency set
19
Torque speed shift 32
fault reset command 33
FWD JOG command 34
REV JOG command 35
JOG order (as F35setting ) 36
prohibition command
37
Motor 12 shift 38
Free stop 39
Up command 40
Down command 41
fuction cancel
42
stop
43
Program running start mode 44
Program running stop mode 45
Pulse counter clearance 46
Pulse counter input 47
Counter loading 48
93

S
e
c
t
i
o
n

V

Upper counter loading 49
(level)
50
1pump soft-start 51
1 pump stop 52
2pump soft-start 53
2 pump stop 54
3pump soft-start 55
3 pump stop 56
4pump soft-start 57
4 pump stop 58
handrotate command 59
Timing Water Supply change
to zero
60
61
62
Program switching to the next
segment
65
UP/DN adjusted value reset 66
value reset
67
(edge)
68

Setting
Value
Output Detail Specification Explaination
0 No function
N- function
1 Forward command FWD
Forward command FWD, Can be set to edge triggered or
level-triggered
2 Reverse command REV
Reverse command REV, Can be set to edge triggered or
level-triggered
3 Three line running STOP o35 setting 3 line running, STOP function
4 Multi-speed command 1
Synthes is of16 multi-speed settings.See H parameter Group
8 multi-acceleration command 1
Synthes is of 8 acceleration settings.See H parameter Group
94

S
e
c
t
i
o
n

V

11 multi-segment digital voltage 1
Synthes is of8digital voltage settings.See H parameter Group 12 multi-segment digital voltage 2
13 multi-segment digital voltage 3
14
frequency
Synthesized frequency given to the way the main switch. See
F parameter group
15
frequency
16
frequency
17
of frequency set 1
Synthesized frequency secondary to the way a given switch.
See F parameter set
18
of frequency set
19
of frequency set
20 MSS timing running 1
Synthes is of segment8 run time setting. See H parameter set. 21 MSS timing running 2
22 MSS timing running 3
23 Operation control mode shift 1
Synthes is of operation mode switching. Read F05 parameter
26 Forward torque limit shift 1
Synthes is of reverse torque limit switch.See C parameter set
C15 Group
29 Reverse torque limit shift 1
Synthes is of reverse torque limit switch.See C parameter set
C16 Group
32 Torque speed shift
Vector control mode, speed control mode and torque control
mode switching.
Disconnected status: Speed Control
Closed Status: torque control
Detail C parameter set C18
33 Fault reset command
Edge-triggered, the fault occurred on the current failure to
confirm or not confirm
34 FWD JOG command JOG forward running command
35 REV JOG command JOG reverse running command
36 JOG command(as F35 setting)
JOGrunning command,direction,set a direction in accordance
with F35.
37
forbid commandr
To maintain the current state to prohibit the acceleration and
deceleration movements.
38 Motor 12 shift
Motor 12 change
Invalid status : Motor 1
95

S
e
c
t
i
o
n

V

Valid status : Motor 2
39 Free stop
Free stop:After free stop, no start command,after 1s, allows
running again
40 Up command Up order, detail A38~A42
41 Down command Down order, detail A38~A42
42
Auto-run feature programs
canceled
Cancle program running function
43
Automatic procedures to
suspend operation
program running pause
44 program running start mode program running start mode
45 program running stop mode program running stop mode
46 pulse count clearance Edge-triggered,frequency inverter pulse countero53Clearance
47 pulse count input Edge-triggered, set the pulse counter input terminal
48 before count loading Edge-triggered, pulse-load preset counter o53counts to o54
49 upper count loading Edge-triggered pulse counter counts o5 maximum load o53
50
(level)
External default signal input(level)level trigger , the
system will alarm E_Set after valid
51 1 pump soft-start
Electric leverl spring, control 1 pump soft-start or stop.
soft-start control must use 2 terminal control, stop priority.
Need to set E01 load model 9, E12 1pump is soft-start
control pump.
52 1 pump stop
53 2 pump soft-start
soft-start control must use 2 terminal control,stop priority.
Need to set E01 load model 9, E12 2pump is soft-start
control pump.
54 2 pump stop
55 3pump soft-start
soft-start control must use 2 terminal control, stop priority.
Need to set E01 load model 9 , E12 3pump is soft-start
control pump. 56 3 pump stop
57 4 pump start
Soft-start control must use two terminal control, stop has
the priority.
Need setting E01 load style 9, E12 4 pump is soft - start
control pump.
58 4 pump stop
59 Hand change order
electric level spring, automation multi-pump constant water
changed
60
the period of time water
supply change to zero
electric level spring the period of time water supply change to
zero
61
DIx input terminal function selection, read o36- 046
62
DIx input terminal function selection, read o36-046.
63 Limit time 1 input DIx input timeing - limit time 1, refer to o65, o67.
96

S
e
c
t
i
o
n

V

64 Limit time 2 input DIx input timeing - limit time 2, refer to o66, o68
65
Program switching to the
next segment
Program running controlled, single trigger switch to the next
segment
66 UP/DN adjusted value reset A40 UP/DN adjusted value reset, level trigger.
67
value reset
A47keyboard potentiometer setting value reset level trigger.
68
(edge)
External default signal input, edge trigger (falling edge),the
system will alarm E-Set after valid
o47
Polarity of input and
output terminals
0000~F7FF - 0000 Y
This parameter used to select every IO terminal is valid in which polarity and terminal running
command is valid or not when power on.
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
14 13 0 1 2 3 4 5 6 7 8 9 10 11 12
DI1
DI2
DI3
DI4
DI5
DI6
DI7
DI8 AI1
AI2
AI3
15
O4
O3
O2
O1
leave unused

0~10 bit Input Terminal Polarity 12~15 bit Output Terminal Polarity

0
Low level valid(closed)
0 Lo w level valid(closed)
Falling edge valid, rising edge invalid
1
High level valid(disconnected)
1 High level valid(cut off)
Rising edge valid, falling edge invalid

o48
Input Terminal Teponse
Time 0
0.001~30.000 s 0.005 Y
o49
Time 1
0.001~30.000 s 0.005 Y
o48,o49define Input terminal reponse time,through o50select the reponse time according theterminal.
o50
Time Selection
0~07FF - 0 Y
DI8
DI7
DI6
DI5
DI4
DI3
DI2
DI1
7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2
0 1 2 3 4 5 6 7 10 9 8
2 2 2
8 9 10
AI1
AI2
AI3

o48,o49define Input terminal reponse time,througho50select the reponse time according theterminal.
The delay time of the input terminal is valid to the close and cut off action!
Set the parameter choose Input terminal reponse time according every terminal.
97

S
e
c
t
i
o
n

V

Setting 0~10 the polarity of input terminal
0 o48 input terminal reponse time 0
1 o49 input terminal reponse time 1

o51 Counter Collocation
1 bit
Circle counter
operating
0
- 0 Y
Single cycle counter
running
1
10 bit
Arrive at upper
counter value and
reload
0
Arrive at upper
counter value and
clear savings
1
100 bit
Power on to reload 0
power on to clear
savings
1
power on to keep
previous count status
2
1000 bit
Count period 0
Output signal valid
time 20ms
1
Output signal valid
time 100ms
2
Output signal valid
time 500ms
3
1 bit: Control count mode
0: Circulate count, Arrive at upper counter value, ouput the arrival pulse(output terminal setting)
1: single circulate count, after arrive at upper counter value, output the arrival pulse, stop running.
10 bit : Operating after circulate mode reach upper limit count
0: Reload
1: Clear up
100 bit: Define the status of the counter after power on
0: Reload after power on
1: Clear up after power on
2: Keep the status of the previous count
1000 bit: Define o21~o24 is set to reach the preset count or counts to reach the maximum output signal
delay time
0: Count period, when reach this digital, keep this status valid, direct the change of the count.
1: the valid time of the output signal10ms, when reach this count, fixed keep the output status valid
10ms.
2: the valid time of the output signal 100ms, when reach this count, fixed keep the output status
valid 100ms.
3: the valid time of the output signal 500ms, when reach this count, fixed keep the output status
valid 500ms.
o52
Maximum Pulse Input
Frequency
0.1~50.0 kHz 20.0 Y
98

S
e
c
t
i
o
n

V

This parameter define the most pulse input frequency of analog setting frequency .
Input high signal frequency, only through multi-function input terminal Di8 as the pulse input
terminal.
input pulse setting frequency according the the most input upper limit.
input pulse setting frequency, most input pulse frequency o52according the most output frequency
F12.
Pulse input frequency f_pulse corresponding setting frequency f_set formula:f_setf_pulse/o52*F12.
Pulse input analog setting, input most pulse frequency o52 according 100.0%.
Pulse input frequency f_pulse corresponding analog p_set formula: p_setf_pulse/o52*100.0%.
o53 Current Counter Status 0~9999 - 0 Y
o54 Preset Counter Setting 0~ o55 - 0 Y
o55
Upper Limit Counter
Setting
o54~9999 - 9999 Y

DiX counting
o21
o22
0 1 2 3 4 5 6 3 4 5 6 3
o54
o55
T
T
the thousand of O51 set t
o55
T
o54
T

When the pulse signal of the input terminal satisfy with the preset condition, Yi terminal output the
corresponding indication.
1 Selection of Input terminal DiXX=1~8
Input terminal is set to pulse count input , and set o54o55.
Input terminal is set to pulse counter clear, after terminal works, counter is cleared.
Input terminal is set to upload of pulse count value, after terminal works, counter uploads preset
count value.
Input terminal is set toupload of upper count value,after terminal works,counter uploads the upper
count value.
2 Selection of Output Terminal o21~o24
o21set the arrival of preset count, the effective time of output signal after reaching up count value is
set by o51.
o22 set the arrival of up count value, the effective time of output signal after arriving at the upper
count value is set by o51.
Frequency range of counting pulse signal: 0~100Hz.
o56
Virtual Terminal
Effective Selection
0000~F7FF - 0000 Y
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
14 13 0 1 2 3 4 5 6 7 8 9 10 11 12
DI1
DI2
DI3
DI4
DI5
DI6
DI7
DI8 AI1
AI2
AI3
15
O4
O3
O2
O1
leave unused

Setting 0~10 Virtual terminal valid choose
0 Actual input terminal valid
1
Virtual input terminal valid
99

S
e
c
t
i
o
n

V

This parameter is used to select a terminal whether each virtual terminal functionality is valid.
o57 DI1~4 Terminal Status 0000~1111 - - Y
o58 DI5~8 Terminal Status 0000~1111 - - Y
o59 AI1~3 Terminal Status 000~111 - - Y
o60 O1~4 Terminal Status 0000~1111 - - Y
Make the actual terminal can only be effective check terminal state.
Make the Virtual terminal can only be effective through register check terminal state.
o61
o62
PL1 Pulse Output
PL2 Pulse Output
No action 0
-
-
0
0
Y
Y
Set frequency 1
Actual frequency 2
Actual current 3
Output voltage 4
DC bus voltage 5
IGBT temperature 6
Output power 7
Output rpm 8
Actual torque 9
o63 SPA pulse output ratio 1~1000 - 1 Y
o64 SPB pulse output ratio 1~1000 - 1 Y
SPA, SPB provide two isolated pulse output signal can be analogical multiple analog output
signals.
SPA, SPB provide high speed pulse output function. Set by o61~o64 and set functions
valid when inverter power on again.
SPA corresponding output signal 1, this function selected, o21 DO1 output action is invalid.
SPB corresponding output signal 2, this function selected, o22 DO2 output action is invalid.
Pulse output ratio = 1, output signal range 0 ~ 50hz.
Maximum pulse output frequency 50 Khz, minimum frequency 1hz.
for example
SPA pulse output options = 2 Actual frequenciy ;
SPA pulse output options = 10
The actual output pulse frequency = actual frequency / maximum frequency * 50hzx10.
SPA pulse output options =3 Actual current
SPB pulse output ratio=20
The actual output pulse frequency = actual current percentage 200*50hz*20
Output Set Value Output Signal Range Definition
No action 0 No output
Set frequency 1 0~Max frequency
Actual
frequency
2 0~Max frequency
100

S
e
c
t
i
o
n

V

Actual current 3 0~200%, corresponding paramerter: S03 output current percentage
Output voltage 4 0~200%, correlation parameter: b02b15 motor rated voltage
Bus voltage 5 0~1000V DC voltage
IGBT
temperature
6 0~100.0
Output power 7 0~200%
Output torque 8 0~Max torque
Actual torque
value
9 0~200% torque

o65
o66
Limit time 1
configuration
Limit time 2
configuration
1 Bit
Boot time 0
-
-
0000
0000
Y
Y
Running timing 1
10Bit Reserved -
100Bit Reserved -
1000Bit Reserved -
1 Bit: Timing mode
0 Boot time , timing of runnig and breaking
1 Running timingonly timing of running
10 BitReserved
100 BitReserved
1000 BitReserved
o67 Limit Time 1 0.0~3200.0 s 2.0 Y
o68 Limit Time 2 0.0~3200.0 s 2.0 Y
Set timeing of limit time 1 , Time limit 2
Actual limit time on the basis of the set time multiplied by a run time multiple, such time
multiple set by the ten bit of F49, refer to F49 instructions.
5-2-6. Multi-speed PLC Group:H00-H55(0x0300-0x0337)
Factory
Setting
Change
Limited
H00 Multi-speed Collocation
1 bit
Program running
function cancel
0
- 0000 Y
Program running
function
1
10 bit
Direction decided by
H40~H46
0
Direction decised by
Terminal and
keyboard
1
100 bit
Deceleration and
acceleration time
decised by H26~H39
0
Time of acceleration
and deceleration
1
101

S
e
c
t
i
o
n

V

isdecided by terminal
1000 bit
Running time
decised by H18~H25
0
Running time
decised by terminal
1
1 bit: Program running functions intelligent
To use the program to run PLC functionality requires setting the bit to 1.
Multi-segment speed run only need to set the corresponding multi-stage o36 ~ o46-speed switching
can be used without the need to set this parameter.
0: Program running functions cancel
1: Program running function intelligent
10 bit: Define program runs or direction settings of multi-segment speed running
0: the direction decided by the H40 ~ H46
1: The directiondecided by the keyboard or terminal
100 bit:Define program runs or acceleration and deceleration time settings of multi-segment speed running
0: deceleration time decided by the H26 ~ H39
1: The acceleration and deceleration time determined by terminal
1000 bit: Set running time of defined program running
0: running-time decided by the H18 ~ H25
1: Running time decided by terminal
H01
Program Running
Configuration
1 bit
sequence control 0
- 0710 Y
terminal control 1
10 bit
Program running
start segment
0~15
100 bit
Program running end
segment
0~15
1000 bit
Output signal valid
time 8ms
0
Output signal valid
time 20ms
1
Output signal valid
time 100ms
2
Output signal valid
time 500ms
3
1 bit: program run control mode
0: sequential control
Run automatically according to the start segment,end segment and program running time of program
running.
You can use o36 ~ o46 switchover next function , switchover to the next program running .
1: Terminal control
Use multi segment control terminal o36 ~ o46 multi segment instruction 1, 2, 3, 4, Control program
segment, running time arrives,Running based on the 0 paragraph speed. After Multi - Stage speed
control terminal switchover, reevaluate running time
Do not use of multi - stage speed control terminal o 36 ~ o46 multi - speed instruction, You can use
o36 ~ o46 switchover next function. The terminal control for single trigger, triggered once, program
running to next paragraph, running time recalculated.Running time of arrival, Running based on the
0 paragraph speed.
10 bit: defining the start running of the Program
100 bit: Defines the end of the program period
102

S
e
c
t
i
o
n

V

1000 bit: Define effective time of the program output signal
H02 Program Running Mode
1 bit
single-cycle 0
- 0000 Y
Continuous Cycle 1
One-cycle command
running
2
10 bit
The zero speed
running when pause
0
Fixed-speed running
when the suspension
1
100 bit
Stop with the
parameters set when
stop
0
Stop with the settings
of start up
1
1000 bit
when start up
segment
0
before the machine
stopped
1
1 bit: Running cycle
0: single cycle
1continuous cycle
2: Single cycle, running according to H01 speed of the end,stop after accepted the stopped orders.
The program runs three styles as following:
Eg1:The program is run single - cycle modes
time
7X
6X
5X
4X
3X
2X
1X
T7 T6 T5 T4 T3 T2 T1
output
frequency
60Hz
50Hz
40Hz
30Hz
20Hz
10Hz
0
10Hz

Eg2:program run Continuous cycle modes
2X
1X
7X
6X
5X
4X
3X
2X
1X
5X
7X
6X
4X
3X
2X
1X
time
STOP
program
running
putput
frequency
60Hz
50Hz
40Hz
30Hz
20Hz
10Hz
0
10Hz

Eg3:Program is running in single cycle, According to Paragraph seventh of Speed mode
103

S
e
c
t
i
o
n

V

output
frequency
time
program
running
STOP
7X
6X
5X
4X
3X
2X
1X
60Hz
50Hz
40Hz
30Hz
20Hz
10Hz
0
10Hz

10 bit: Running condition when pause
0: speed run when pause
1: fixed Segment Speed operation when pause
100 bit: Running Segment when stop
0: Set stopping according to the parameters of stop segment.
1: Set down to the initial segment
1000 bit: start Running Segment
0: Set down to the speed running
1: Running at the speed before the machine stopped.
100 bit=0 Set stopping according to the parameters of stop segment
1000 bit=0 running at Start Segment
STOP
RUN
T2 T1
3X
2X
1X
F51=00
T1 T2 X
1X
2X
3X
dt3' at1'
time
output
frequency

Eg:100 bit==0 Set stopping according to the parameters of stop segment
1000 bit==1 Running at the speed before the machine stopped.
5X
X+Y=T3
3X
2X
1X
X T2 T1
F51=01
3X
4X
Y T4
RUN
STOP
dt3'
at3'
time
output
frequency

Eg:100 bit=1 Set down to the initial segment
1000 bit=1 Running at the speed before the machine stopped.
at1' dt1'
3X
2X
1X
X T2 T1
F51=10,11
1X
2X
3X
T1 T2
RUN
STOP
time
output
frequency

Note at1at the time of segment 1 acceleration time dt1at the time of segment 1 deceleration
time at3at the time of segment 3 acceleration timedt3at the time of segment 3 deceleration time
104

S
e
c
t
i
o
n

V

H03
1 Segment Speed
Setting 1X
Lower frequency ~ upper frequency Hz 3.00 Y
H04
2 Segment Speed
Setting 2X
H05
3 Segment Speed
Setting 3X
H06
4 Segment Speed
Setting 4X
H07
5 Segment Speed
Setting 5X
H08
6 Segment Speed
Setting 6X
H09
7 Segment Speed
Setting 7X
H10
8 Segment Speed
Setting 8X
H11
9 Segment Speed
Setting 9X
H12
10 Segment Speed
Setting 10X
H13
11 Segment Speed
Setting 11X
H14
12 Segment Speed
Setting 12X
H15
13 Segment Speed
Setting 13X
H16
14 Segment Speed
Setting 14X
H17
15 Segment Speed
Setting 15X
Set the frequency of program running and the running frequency of 7-segment speed respectively.
short-circuit the multi-terminal command 1, 2, 3, 4 with COM combinatorially to realized the 16-segment
speed/acceleration speed.
0Xspeed is the regular running mode,setting source can be adjusted by F02,F03and other parameters,
running time is controlled by the H18.
Terminal multi-segment speed is defined as follows(shorted with COM it is ON, disconnected then it
is OFF):
Speed
Terminal
0X 1X 2X 3X 4X 5X 6X 7X
Multiterminal-speed Command 1 OFF ON OFF ON OFF ON OFF ON
Multiterminal-speed Command 2 OFF OFF ON ON OFF OFF ON ON
Multiterminal-speed Command 3 OFF OFF OFF OFF ON ON ON ON
Multiterminal-speed Command 4 OFF OFF OFF OFF OFF OFF OFF OFF
Speed
Terminal
8X 9X 10X 11X 12X 13X 14X 15X
Multiterminal-speed Command 1 OFF ON OFF ON OFF ON OFF ON
Multiterminal-speed Command 2 OFF OFF ON ON OFF OFF ON ON
105

S
e
c
t
i
o
n

V

Multiterminal-speed Command 3 OFF OFF OFF OFF ON ON ON ON
Multiterminal-speed Command 4 ON ON ON ON ON ON ON ON
Acceleration and deceleration time and the direction of running
0X-7X 8X-15X
H00
10 bit
0 0X -7X Direction controlled by parameter
8X-15X Direction controlled
by keyboard and terminal
1
0X -7X Direction controlled by keyboard
and terminal
H00
100 bit
0
0X -7Xdeceleration and accelertation time
controlled by parameter
8X-15Xdeceleration and
accelertation time controlled
by keyboard and terminal 1
0X -7X deceleration and accelertation time
controlled by terminal
H00
1000 bit
0
0X -7Xrunning time controlled by
paremeter
8X-15Xrunning time controlled
by terminal
1 0X -7Xrunning time controlled by terminal

H18
0 Segment Running
Time T0
0.0~3200.0 s 2.0 Y
H19
1 Segment Running
Time T1
0.0~3200.0 s 2.0 Y
H20
2 Segment Running
Time T2
0.0~3200.0 s 2.0 Y
H21
3 Segment Running
Time T3
0.0~3200.0 s 2.0 Y
H22
4 Segment Running
Time T4
0.0~3200.0 s 2.0 Y
H23
5 Segment Running
Time T5
0.0~3200.0 s 2.0 Y
H24
6 Segment Running
Time T6
0.0~3200.0 s 2.0 Y
H25
7 Segment Running
Time T7
0.0~3200.0 s 2.0 Y
Actual running time equals to the set multi-segment running time multiples a time which is times of
speed running time, and such actual running time decided by the tens digit of H40~H46. Please refer to
H40~H46.
H26
1 Segment
Acceleration Time at1
0.0~3200.0 s 10.0 Y
H27
1 Segment
Deceleration Time dt1
0.0~3200.0 s 10.0 Y
H28
2 Segment
0.0~3200.0 s 10.0 Y
H29
2 Segment
0.0~3200.0 s 10.0 Y
H30
3 Segment
0.0~3200.0 s 10.0 Y
H31
3 Segment
0.0~3200.0 s 10.0 Y
106

S
e
c
t
i
o
n

V

H32
4 Segment
0.0~3200.0 s 10.0 Y
H33
4 Segment
0.0~3200.0 s 10.0 Y
H34
5 Segment
0.0~3200.0 s 10.0 Y
H35
5 Segment
0.0~3200.0 s 10.0 Y
H36
6 Segment
0.0~3200.0 s 10.0 Y
H37
6 Segment
0.0~3200.0 s 10.0 Y
H38
7 Segment
0.0~3200.0 s 10.0 Y
H39
7 Segment
0.0~3200.0 s 10.0 Y
Set the Acc/Dec time of 7 steps respectively. They determine the time needed to reach the speed,
respectively depending on the acceleration time for acceleration or on the deceleration time for
deceleration, but the time is not the actual time needed. Actual acc/dec time equals to the set acc/dec
time multiples a time multiple which is decided by the hundreds and thousands digit of H40~H46.
Please refer to H40~H46.
Definite acceleration and deceleration time for multi-step speed:
output
frequency
time
Definition of multi-step speed acceleration/deceleration time
T3 T2 T1
dt3 dt2
at2
at1
3X
2X
1X

Remark: at1: 1 segment acceleration time;at2: 2 segment acceleration time;dt2: 2 segment deceleration
time;dt3: 3 segment deceleration time.
H40
H41
H42
H43
H44
H45
H46
1 Segment Speed
Configuration Word
2 Segment Speed
Configuration Word
3 Segment Speed
Configuration Word
4 Segment Speed
Configuration Word
5 Segment Speed
Configuration Word
6 Segment Speed
Configuration Word
7 Segment Speed
Configuration Word
1 bit
Running direction:
forward
0
-
-
-
-
-
-
-
0000
0000
0000
0000
0000
0000
0000
Y
Y
Y
Y
Y
Y
Y
Running direction:
reverse
1
10 bit
Running time:
*seconds
0
Running time:
*munites
1
Running time:
*hours
2
Running time: *days 3
100 bit
Acceleration time:
*seconds
0
Acceleration time:
*munites
1
107

S
e
c
t
i
o
n

V

Acceleration time:
*hours
2
Acceleration time:
*days
3
1000 bit
Deceleration time:
*seconds
0
Deceleration time:
*munites
1
Deceleration time:
*hours
2
Deceleration time:
*days
3
1 bit: Under multi-segment program running, the1 bitparameter decides the direction of each segment
speed.
Running Direction Setting Value
forward 0
reverse 1
When running control modeF050/1/2,these parameters decide the direction of each segment
speed.
When running control mode F053, the setting value and terminal FWD/REV decide the direction
of each segment speed together. FWD is prior.
FWD=1
Running direction
REW =1
Running direction
Setting Value
forward reverse 0
reverse forward 1
10 bit: Unit of multi-segment speed program running time.
Running Time 10 bit Range(e.g.H18~H25=3200.0)
*seconds 0 3200.0 seconds
*minutes 1 3200.0 minutes
*hours 2 3200.0 hours
*days 3 3200.0 days
100 bit, 1000 bit : Unit of acc/deceleration time of multi-segment speed program running
Acceleration
/ Deceleration time
1000 bit, 100bit Range(e.g.H26~H39=3200.0)
*seconds 0 3200.0 seconds
*minutes 1 3200.0 minutes
*hours 2 3200.0 hours
*days 3 3200.0 days

H47
0 Segment Digital
Voltage Giving
-100.0~100.0 % 0.0 Y
H48
1 Segment Digital
Voltage Giving
-100.0~100.0 % 10.0 Y
H49
2 Segment Digital
Voltage Giving
-100.0~100.0 % 20.0 Y
108

S
e
c
t
i
o
n

V

H50
3 Segment Digital
Voltage Giving
-100.0~100.0 % 30.0 Y
H51
4 Segment Digital
Voltage Giving
-100.0~100.0 % 40.0 Y
H52
5 Segment Digital
Voltage Giving
-100.0~100.0 % 50.0 Y
H53
6 Segment Digital
Voltage Giving
-100.0~100.0 % 60.0 Y
H54
7 Segment Digital
Voltage Giving
-100.0~100.0 % 70.0 Y
Digital voltage set function can analogy give frequency, select by F02, F03;analogy give PID set
or feedback, select by P02, P03;it can be shifted by the input terminal o36~o46.
H55 Multi-speed Status
1 bit Current speed step 0~0xF
- - N
10 bit
Current acceleration
segment
0~0x7
100 bit
Current running time
segment
0~0x7
1000 bit
Current digit voltage
segment
0~0x7
1 bit: Current speed segment
0~16 segment, In hex, can be shifted t by o36~o46
10 bit: Current acceleration segment
0~7 segment, in hex, can be shifted by o36~o46
100 bit: Current running time segment
0~7 segment, in hex, can be shifted by o36~o46, valid when program running
1000 bit: Current digital voltage segment
0~7 segment, in hex, can by shifted by terminal o36~o46
5-2-7. V/Fcurve Group:U00-U15(0x0400-0x040F)
Factory
Setting
Change
Limited
U00 V/ Setting Frequency1 0.00~U02 Hz 5.00 N
User-defined the first frequency value of V / F curve, corresponding to V1
V8
V7
V6
V5
V4
V3
V2
V1
F1 F2 F3 F4 F5 F6 F7 F8
max
output
max
frequency
(0,0)
output frequency
output voltage

U01 V/F Setting Voltage 1 0~U03 % 10 N
User-defined the first voltage percentage of V / F curve, on the base of rated output voltage 100%
of frequency inverter, corresponding to F1.
109

S
e
c
t
i
o
n

V

U02 V/F Setting Frequency 2 U00~U04 Hz 10.00 N
User-defined the second frequency value of V / F curve, corresponding to V2.
U03 V/F Setting Voltage 2 U01~U05 % 20 N
User-defined the second voltage percentage of V / F curve, on the base of rated output voltage
100% of frequency converter, corresponding to F2.
User-defined the third frequency value of V / F curve, corresponding to V3.
User-defined the third voltage percentage of V / F curve, on the base of rated output voltage 100%
of frequency converter, corresponding to F3.
User-defined the fourth frequency value of V / F curve, corresponding to V4.
User-defined the fourth voltage percentage of V / F curve, on the base of rated output voltage 100%
User-defined the fifth frequency value of V / F curve, corresponding to V5.
User-defined the fifth voltage percentage of V / F curve, on the base of rated output voltage 100%
User-defined the sixth frequency value of V / F curve, corresponding to V6.
User-defined the sixth voltage percentage of V / F curve, on the base of rated output voltage 100%
User-defined the seventh frequency value of V / F curve, corresponding to V7.
User-defined the seventh voltage percentage of V / F curve, on the base of rated output voltage
100% of frequency converter, corresponding to F7.
U14 V/F Setting Frequency 8 U12~most frequency Hz 40.00 N
User-defined the eighth frequency value of V / F curve, corresponding to V8.
U15 V/F Setting Voltage 8 U13~100 % 80 N
User-defined the eighth voltage percentage of V / F curve, on the base of rated output voltage 100%
5-2-8. PID parameter:P00-P12(0x0500-0x050C)
Factory
Setting
Change
Limited
P00 PID Configuration 1 bit
Unidirectional
regulation
0
- 0000 N
Bidirectional
regulation
1
110

S
e
c
t
i
o
n

V

10 bit
Negative effect 0
Positive effect 1
100 bit
PID fault, N action 0
Warning &
Continuous running
1
Warning &
Decelerating stop
2
Warning & Free stop 3
1000 bit
- -
- -
When the inverter receives running command, it can control output frequency automatically in the
PID regulation mode after comparing the setting signal and feedback signal from terminal. The process
is explained as following:
PID inverter
setting signal
+
-
M
f
feedback signal
( = setting signal - feedback signal)
PI8000/PI8100 PID regulation

0: negative action, when 0 is positive, frequency rises and when 0 is negative, frequency
falls.
1: positive action, when 0 is positive, frequency falls and when 0 is negative, frequency
rises.
PID abnormity treatment:
1: Warning & Continuous running: continue running g after abnormity feedback signal.
2: Warning & Decelerating stop: decelerate and stop after abnormity feedback signal.
3: Warning & Free stop: free stop after abnormity feedback signal .
P01 PID Output Limit 0~100 % 100 Y
The parameter defines the limited range of the output when using PID control.
P02
Feedback Signal
Selection
RS485
0
- 1 Y
Keyboard potentiometer giving
4
muti-step digital voltage giving 5
Digital pulse set 6
PID feedback signal selection, can select keyboard/Rs485, potentiometer, digital voltage, digital
pulse for feedback signal.
P03 Setting Signal Selection
RS485
0
- 2 Y
Keyboard potentiometer giving 4
111

S
e
c
t
i
o
n

V

Multi-step digital voltage giving 5
Digital pulse set 6
PID giving signal selection, can select keyboard/Rs485, potentiometer, digital voltage, digital pulse
for giving signal.
P04 Keyboard Set Signal 0.0~100.0 % 50.0 Y
When P03 is 0, the setting pressure set by the keyboard. 0.0~100.0% is 0 to the maximum pressure
respectively.
P05 PID integral time 0.002~10.000 s 0.250 Y
0.002~10.000s
The PID integral time determines the integral regulation speed,the regulation acts on the difference
between PID feedback and setting value by PID regulator.
When the difference between PID feedback and setting value is 100% , integral regulator PID
regulator ouput=(P01*F12*12.5%)Hz.(single direction PIDregulation,ignores proportion and differential
effect).
If the value is great,the control is stable but response is slow;if the value is little,the system response
is rapid but perhaps surge occurs.
difference
operation value
time
time

P06 PID Differencial Time 0.000~10.000 s 0.000 Y
0.000~1.000s
The parameter determines the regulation intensity, the regulation acts on the change ratio of the
difference between PID feedback and setting value by PID regulator.
When the change ratio of the difference between PID feedback and setting value is 100% in the
differential time, PID regulator regulates output to(P01*F12*12.5%)Hz (single direction PID regulation,
ignores proportion and integral effect).
If the value is great, the greater the intensity is, the system surge is to occur more easily
P07 PID Proportion Gain 0~1000.0 % 100.0 Y
time
time
operation value
difference

0~100.0%
The PID Proportion Gain defines regulation intensity of PID regulator, the larger the P is, the more
the intensity is.
When proportion gain is 100%,and the difference between PID feedback and getting value is 100%,
PID regulators output is(P01*F12*12.5%)Hz(single direction PID regulation,ignores differential and
integral effect).
Proportion gain is the parameter decides PID regulators response extent.
112

S
e
c
t
i
o
n

V

If the gain is great, the response is rapid, but if too great, the surge will occur; the gain is little, the
response will lag.
P08 PID Sampling Period 0.002~10.000 s 0.010 Y
Set Sampling period of feedback signal.
When set this parameter small, the system response speed to the giving and feedback deviation is
slow, but control is stable.
When set this parameter low,the system response speed to the giving and feedback deviation is slow,
but easy to cause vibration
P09 Deviation Limit 0.0~20.0 % 5.0 Y
Deviation limit effects system control accuracy and stability.
When the deviation of feedback signal and giving signal <deviation limit, PID N regulation, keep
output stable.
When the deviation of feedback singnal and giving signal >deviation limit, PID regulates according
to deviation, update output
P10 PID Fault Detect Time 0.0~3200.0 s 0.0 N
P11 PID Fault Detected Value 0.0~100.0 % 10.0 N
Set P10 to 0. 0 for N fault inspection.
When PID feedback signal <P11 set PID fault inspection value, last P10set time, regard it as PID
regulation fault.
P12 PID Display Range 0.00~100.00 - 1.00 Y
A09 PID set valuePID set value(%)*P12
A10 PID feedback valuePID feedback value(%)*P12
If PID feedback 10V corresponding 4.0Mpa pressure, if need A09, A10 to display actual value,
only need to set P12 = 0.04.
5-2-9. Expanding parameters:E00-E23(0x0600-0x0617)
Factory
Setting
Change
Limited
E00 Load Type
General 0
- 0 N
Pump 1
Fan 2
Injection machine 3
Textile machine 4
Hoist machine 5
Kowtow Machine 6
belt conveyor 7
Variable frequency power 8
Multi-pumps constant pressure
water supply
9
Reserved 10
Reserved 11
Torque control 12
Voltage regulation power 13
Current regulation power 14
113

S
e
c
t
i
o
n

V

Extruding machine 15
Details, see Appendix IV.
E01
Starting Pressure
Deviation
0.0~100.0 % 10.0 Y
E02 Starting Delay Time 0.0~3200.0 s 5.0 Y
Feedback pressure <given pressure starting pressure deviation.
Continuously exceed E02 start delay time, the inverter will restart under in the standby mode.This
parameter is used to prevent the inverter frequent start-stop.
E03 Stop Frequency 0~50.00 Hz 5.00 N
E04 Stop Delay Time 0.0~3200.0 s 5.0 Y
If the set frequency is less than or equal to E03, stop frequency exceeding E04 stop delay time, the
ac drive will change from running to the stop standby state.
The bigger E03 parameter setting, the easier for stop, E03 parameter is set to 0, indicating the stop
frequency and the start pressure control function is invalid.
E01, E02, E03,E04 mix are used to control system operation and water supply systems in the energy
-saving water pressure regulator.
For example:
Given pressure = 50%
Starting pressure deviation =10%, starting pressure = given pressure - starting pressure deviation=
40%
Topping frequency= 5Hz
actual frequency
H08
H07
0
upper frequency
time
lower frequency
stop pressure
frequency
pressure
feedback pressure
start pressure
10
time
set pressure
50
0

E05
High Pressure Arrival
Value
0~100.0 % 90.0 Y
When feedback pressure reach and exceed the high pressure reached value of this parameter, the I/O
output terminal select 25, then it will output arrival signal.
E06
Low Pressure Arribal
Value
0~100.0 % 10.0 Y
When feedback pressure less than the low pressure reached value of this parameter, the I / O output
terminal select 26, then it will output arrival signal.
E07
Timing To Supply
Water
1 bit
Timing
water
supply
invalid 0
- 0000 Y
Valid 1
10 bit
Pressure
giving
Set
according
0
114

S
e
c
t
i
o
n

V

to P03
Set
according to
H47~H54
1
100 bit
Timing
mode
Circle
mode
0
Single
circle
1
1000 bit Current timing step
1 bit: Timing water supply
0 Timing water supply function is invalid
1 Timing water supply function is valid
10 bit: pressure giving
0 the pressure given during regular pressure water supply is set according PID given value selecting
P03.
1 the pressure given during regular pressure water supply is set according the current corresponding
H47~H54 digital voltage given.
100 bit: timing mode
0 cycle mode
Start to time from start running, after it reached the setting time, the inverter will automatically
move to the next period of time set, after the end of a loop, it will automatically re-start from the
first paragraph 0, then cycle to run.
1 single cycle
Start to time from start running, after it reached the setting time, the inverter will automatically
move
to the next period of time set, after the end of a loop, the inverter will stop and wait for the next
running command.
1000 bit: the current regular time
When the water supply time set 0, it means cancel the water supply time setting of this period.
Current time Water supply time Pressure given
0 H18 H47
1 H19 H48
2 H20 H49
3 H21 H50
4 H22 H51
5 H23 H52
6 H24 H53
7 H25 H54
E08
Timing Shift
Alternation Time
0.0~3200.0 Hours 0.0 N
Timing Shift Alternation Time control the alternation ways and time of pump.
When Timing Shift Alternation Time is set to 0.0 hour and cancel Timing Shift Alternation function.
When the Timing Shift Alternation Time between 0.1~3,200 , after corresponding time of the stable
running, in accordance with the principle of first stop for the one first started to control switch of pump.
First stop for the first pump started: When reduce pumps control, stop the first pump which started
first.
According to the principle of start first stop first control, in order to ensure that every pump can
115

S
e
c
t
i
o
n

V

have the chance to run to prevent some pumps rusted as a result of no use for long , such as the need to
ensure that each operation of the pump can receive equal time, set Timing Shift Alternation Time.
Pump alternation order : E12 = 0x 0001
Starting State : No. 1 pump frequency, No. 2 pump frequency conversion and No. 3 pump stops ;
Rotation : No. 1 pump stops, No. 2 pump frequency, No. 3 pump frequency conversion ;
After the second rotation : No.1pump frequency conversion and No.2pump stops, No.3pump power
frequency.
E09
Electromagnetic
Switch Action Delay
0.000~10.000 s 0.500 Y
Electromagnetic switch action delay time when set up a pump (drive motor) to switch from variable
frequency to industry frequency,or from industry frequency to variable frequency.This is to avoid inverter
output frequency meet with the AC power supply and occur short circuit caused because electromagnetic
switch action too slow.
E10
Pumps Shift Judging
Time
0~9999 s 5 Y
Set when output frequency converter arrives to upper frequency, until the judgment time of
increasing pumps (driving motor); or when output frequency converter arrives to lower frequency, until
the judgment time reducing pumps ( driving motor). Set the time long or short according to the speed of
pressure change, without oscillating range, the shorter the better.
Drives add or subtract pump control with E12 Water Supply Configuration
Add pump order No. 1 pump No. 2 pump No. 3 pump No. 4 pump.
Reduce pump order No. 4 pump No. 1 pump No. 2 pump No. 3 pump.
If the current : No. 1 pump frequency, No. 2 pump frequency, No. 3 pump convert frequency
after reduce pump: No. 1 pump frequency, No. 2 pump convert frequency,
after add pump: 1 pump frequency, No. 2 pump frequency, No. 4 pump convert frequency
after reduce pump :No. 1 pump frequency, No. 2 pump convert frequency,
after reduce pump: No. 1 pump frequency,
after add pump: No. 1 pump frequency, No. 3 pump convert frequency
after add pump: No. 3 pump frequency No. 4 pump convert frequency
after add pump: No. 1 pump frequency, No. 3 pump frequency No. 4 pump. frequency ,No. 2 pump
converter frequency,
E11
Constant Pressure
Water Supply
Configuration
1 bit
Stop
mode
all pumps
slow down
stop
0
- 0000 N
Variable
frequency
pump stop
1
Free stop 2
Water supply
Pump stop
3
10 bit
Pumps
status
when
fault
occurs
Keep
current
situation
0
All-pumps
stop
1
100 bit
Altern
ation
Variable
frequency to
0
116

S
e
c
t
i
o
n

V

shift
mode
working
frequency
Variable
frequency to
stop
1
1000 bit
Pump
status
keep
Keep status 0
Stop reset 1
1 bit : Stop mode
0 All slow down, all pumps in turn slowing down.
1 variable frequency pump stop:variable frequency pump stop running,variable frequency pump and
soft start pump under frequency keep running.
Stop power frequency pump,you need to use o36~o46parking command or keyboard input terminal
free multi - function keys MF1, MF2 set to 2 : Free Parking function.
2 Free stop, all pumps free stop
After free stop,E11 1000bit pump reset according to the order start and stop,but reorder according to
E12 multi - pumps configuration.
3 Water supply pump stops,only those constant pressure water supplying pumps stop,soft start pump
keep running under pump frequency.
Stop soft - starting pump, you need to use stop command of the soft star pump for o36 ~ o46 input
terminal or keyboard multi - function keys MF1, MF2 set to 2 : Free stop function.
10 bit: Treatment under fault pump states
0 maintain the status quo, when inverter failure, stop the current variable frequency pump operation
and other power - frequency operation of variable frequency pump and soft start pump maintain the
status quo
Fault occurs, if the following breakdown, select fault treatment according to failure action.
12 E.PId regulating fault
13 E.OHt Motor over heated fault
14 E.OL2 Motor over loading fault
15 E.PG PG fault
16 E.PHo Inverter output Phase lost
17 E.COA RS485 communication A fault
18 E.COb RS485 communication B fault
The feature only applies to the fault under the mode allowing fault runs. The fault is not allowed to
run, all stop.
1 All pump stop, when inverter failure, all pumps free stop.
100 BitSoft start switching mode
0 Convert frequency to power frequency, frequency control of the pump current increases the speed
to the frequency, the rotation of the pump start and stop switch control or soft start pump
1 Frequency conversion to stop, stopped the current frequency conversion control of pump and
pump rotation switch or soft start pump start - stop control.
1000 Bit : pumping States maintain
0 Maintaining state, After multi pumps constant pressure water supply stop, keep the current
multipumps at the first start- first stop order.
1 Stopping reset , After multi pumps constant pressure water supply stop , E12 multipumps
117

S
e
c
t
i
o
n

V

configuration reorder multi - pump at the stop order.
E12
Multi-pumps
Configuration
1 bit
Pump 1 invalid 0
- 0001 N
Pump 1 variable
pump
1
control pump
2
10 bit
Pump 2 invalid 0
Pump 2 variable
pump
1
control pump
2
100 bit
Pump 3 invalid 0
Pump 3 variable
pump
1
control pump
2
1000 bit
Pump 4 invalid 0
Pump 4 variable
pump
1
control pump
2
Under Multi-pump control mode, set the control mode of each pump.
E13 Multi-pumps Status
1 bit
Pump 1 stop 0
- 0000 N
Pump 1 run in
variable frequency
1
Pump 1 run in
working frequency
2
10 bit
Pump 2 stop 0
Pump 2 run in
variable frequency
1
Pump 2 run in
working frequency
2
100 bit
Pump 3 stop 0
Pump 3 run in
variable frequency
1
Pump 3 run in
working frequency
2
1000 bit
Pump 4 stop 0
Pump 4 run in
variable frequency
1
Pump 4 run in
working frequency
2
118

S
e
c
t
i
o
n

V

Under Multi-pump control mode, displays the status of each pump.
E14
Soft Starting Pump
Control
1 bit
Pump 1 soft-no
command
0
- 0000 Y
Pump 1 soft-stop 1
Pump 1 soft-start 2
10 bit
Pump 1 soft-no
command
0
Pump 2 soft-stop 1
Pump 2 soft-start 2
100 bit
Pump 1 soft-no
command
0
Pump 3 soft-stop 1
Pump 3 soft-start 2
1000 bit
Pump 1 soft-no
command
0
Pump 4 soft-stop 1
Pump 4 soft-start 2
Under Multi-pump control mode, set the control mode of each pump.
E15 User Parameter 0 0~9999 - 0 Y
0~9999
- 0 Y
E20 User parameter 5
0~9999
- 0 Y
0~9999
- 0 Y
Please check appendix 4 for the detailed expanding parameter instruction.
5-2-10. Speed-loop parameter [SPD]:C00-C31(0x0700-0x071F)
Factory
Setting
Change
Limited
C00
Filter Time Of
Speed-loop
2~200 ms 10 Y
It defines the filter time of the speed-loop. The range is 0.01~100s.If the value is too great, the
control is stable but response is slow; if the value is too little, the system response is rapid but perhaps is
unstable. So it is necessary to consider the stability and the response speed at the same time when setting
the value.
C01
Ti
0.01~100.00 s 0.25 Y
It defines the integral time of the speed-loop low speed. The range is 0.01~100.00s. If the integral
time is too great, response is slow and the control of external disturbing signal become bad; if the time is
too little, response is rapid, but perhaps brings the surge.
C02 Speed-loop Low Speed 0.000~1.000 s 0.000 Y
119

S
e
c
t
i
o
n

V

Td
It defines the differential time of the speed-loop low speed segment and the range is 0.000~1.000s.
If the time is great enough, the surge which is caused by P action when difference occurring can
attenuate quickly. But too great, the surge will happen contrary. When the time is little, the attenuation
function is little too.
C03 Speed-loop Low Speed P 0~150 % 100 Y
It defines the proportion gain of speed loop low speed segment.And the range is 0~1000%.If the
gain is great, the response is rapid, but too great, surge perhaps occurs; if the gain is too little, response is
slower.
C04
Shift Frequency
0.0~C08 Hz 7.00 Y
It defines low-speed loop switching frequency, the parameter and switching frequency at high-speed
optimize Speed-loop PID parameter.
C05
Speed Loop High
Speed Ti
0.01~100.00 s 0.50 Y
It defines integration time of High-speed section of the speed loop.Range is0.01~100.00s.integration
time too large and unresponsive, external interference control variation becomes weak ; integration time
is small the reaction speed, oscillation occurs when it is too small.
C06
Speed Loop High
Speed Td
0.000~1.000 s 0.000 Y
It defines the differential time of the speed-loop high speed segment and the range is 0.000~1.000s.
If the time is great enough, the surge which is caused by P action when difference occurring can
attenuate quickly. But too great, the surge will happen contrary. When the time is little, the attenuation
function is little too.
C07
Speed Loop High
Speed P
0~150 % 75 Y
It defines the proportion gain of speed loop high-speed section, range from 0~1000%. Gain is large,
response speed, but too large gain will occur vibration; if the gain is small, the reaction lag.
C08
Speed Loop And
High-speed Switching
Frequency
C04~max frequency Hz 30.00 Y
It defines Integral time of speed loop high speed , the parameter and switching frequency at low -
speed optimize the speed-loop PID parameter.
C09 Low-speed Slip Gain 0~200 % 100 Y
Low-speed segment slip compensation gain
C10
Low Speed Slip
Switching Frequency
0~C12 Hz 5.00 Y
Low speed segment slip compensation switching frequency
C11 High Speed Slip Gain 0~200 % 100 Y
High speed segment slip compensation gain
C12
High Speed Slip
Switching Frequency
C10~ max frequency Hz 30.00 Y
High speed segment slip compensation switching frequency
C13 Upper Froward Torque 0.0~300.0 % 250.0 Y
120

S
e
c
t
i
o
n

V

The parameter is a ratiosetting value is 100%. Responding to motor rated output torque.
Set forward torque mode through C15.
In speed control mode, its upper forward torque.
In torque control mode, its forward torque setting value.
C14 Upper Reverse Torque 0.0~300.0 % 250.0 Y
The parameter is a ratiosetting value is 100%.
Set reverse torque mode through C16.
In speed control mode, its upper reverse torque.
In torque control mode, its reverse torque setting value.
C15
Forward
Torque setting
mode
1 bit
Setting
mode
Set by keyboard or
RS485
0
- 0000 Y
giving
1
giving
2
giving
3
giving
4
Multi-step digital
voltage giving
5
Digital pulse set 6
10 bit direction
C16
Reverse
Torque setting
mode
1 bit
Setting
mode
Set by keyboard or
RS485
0
- 0000 Y
AI1 external analogy 1
giving
2
giving
3
giving
4
Multi-step digital
voltage giving
5
Digital pulse set 6
10 bit direction
121

S
e
c
t
i
o
n

V

C17 Torque Set Gain 0.0~300.0 % 200.0 Y
C15 1 bitSetting mode
C16 1 bitSetting mode
0 Set by keyboard or RS485 Responding to C13/C14
1 AI1 external analog setting As per AI1 external analog setting
4 Keyboard potentiometer setting As per keyboard potentiometer setting
5 Multi segment digital voltage setting As per multi segment digital voltage setting
6 Digital Pulse Setting As per digital pulse setting
While the unit digital of C15,C16 is 16, the torque up-limit of C13,C14 is for checking.
C15 10 bit: Direction Control
C16 10 bit: Direction Control
0: No control Direction
Direction is controlled by terminal or keyboard
1:Control Direction
Setting value of forward torque > setting value of reverse torque, forward direction.
Setting value of forward torque < setting value of reverse torque, reverse direction.

C13 upper forward torque =setting value percentage * C17 torque given gain.
C14 upper reverse torque =setting value percentage * C17 torque given gain.
Such as:
C15 forward torque setting way=4 keyboard potentiometer setting.
C16 reverse torque setting way=4 keyboard potentiometer setting.
Forward/reverse both can control direction, C15=0x14C16=0x14.
Potentiometer corresponding setting value A48=-100%A49=100%
Keyboard potentiometer set A47=100%C17=200.0%
C13 forward torque up-limit=100%*200.0%=200.0%, control direction forward 200% torque
Keyboard potentiometer set A47=100%C17=200.0%
C14 reverse torque up-limit=100%*200.0%=200.0%, control direction reverse 200% torque
C18
Speed /Torque Control
Shift
Speed control 0
- 0 Y
Torque control 1
F00 control method is to s select senseless vector control or sensor feedback close loop vector control,
can change speed or torque control through input terminal. After setting IP terminal change, keyboard set
invalid, only for query.
C19
Upper speed
Setting mode
1 bit
Separate
setting
mode
keyboard or RS485
setting
0
- 0000 Y
AI1 external analog
setting
1
AI2 external analog
setting
2
AI3 external analog
setting
3
122

S
e
c
t
i
o
n

V

Keyboard
potentiometer setting
4
voltage setting
5
10 bit Selection
C19 Unit bit setting 0
S00 Setting Frequency 1
C20 Reverse Speed Limit 0.00~ Maximum frequency - 50.00 Y
While torque control, setting upper speed.
C19 1 bit: Separate setting mode
0 keyboard or RS485 setting As per C20 setting
4 Keyboard potentiometer setting As per keyboard potentiometer setting
5 Multi-step digital voltage setting As per Multi-step digital voltage setting
6 Digital Pulse Setting As per Digital Pulse Setting
While the unit digital of C19 is 16, the speed up-limit of C20 is for checking.
C19 10 bit; Select Speed Up-limit Setting Ways
0: separate setting, as per the selection of C19 Units digital.
1:setting frequency is according to S00,and affected by the following parameters.
F02 frequency main setting ways/F03 frequency secondary setting ways/F04 frequency setting
main and secondary.
C21
Torque Acceleration
Time
0.0~200.0 s 1.0 Y
C22
Torque Deceleration
Time
0.0~200.0 s 1.0 Y
C21, C22 torque acceleration time, turning moment deceleration torque control mode and effective.
Torque acceleration time, torque accelerated from 0 to 300 hours.
Torque speed, torque, from 300 down to 0.
C23
Low Speed Exitation
Excitation
0~100 % 30 Y
Under low speed, compensate excitation quantity, increase torque feature, in case of meeting the
requirement, try to make it lower, could reduce the motor heating up caused by magnetic path full.
C24 Current Loop Ti 0~9999 ms 500 Y
Define the current loop integral time. When integral time is too long, response is inactive; the
ability to control external jamming becomes weak. When integral time is short, response is fast, if too
short, vibration will occur.
C25 Current Loop P 0~1000 % 100 Y
Define current loop proportion gain, When select big gain, response fast, but too big will occur
vibration. when select low gain, response lag.
123

S
e
c
t
i
o
n

V

C26 PG Electronic Gear A 1~5000 - 1 Y
C27 PG Electronic Gear B 1~5000 - 1 Y
When encoder and motor is in different shaft, can calculate current motor speed according to
encoder and gear ratio.
Electronic gear A for denominator, B for molecule.
C28 PG Pulse 300~9999 - 2500 N
PG pulse quantity used, set value is the pulse quantity when motor rotates for a circle.
C29 Action When PG Break
N PG break protection 0
- 3 Y
Warning and keeping running 1
Warning and deceleration stop. 2
Warning and free stop. 3
Set the brake method when detect PG break.
0 : N PG break protection
1 : Warning and keeping running.
2 : Warning and deceleration stop.
3 : Warning and free stop.
C30 PG Rotating Direction
leads
0
- 0 Y
leads
1
phase A
phase B
phase A is forward
phase A
phase B
phase B is forward

Encoder rotating direction, refer to the motor forward direction
0 : When motor forward, phase A leads, set C27= 0
1 : When motor forward, phase B leads, set C27= 1
Note: above parameters are valid when with encoder(PG), need to layout PG card. If needed, please
contact our company.
C31
PG Dropped
Inspection Time
0.0~10.0 s 1.0 N
PG feedback signal is 0, exceed C31 set time, system reports PG dropped fault. Set speed to 0, or
sert C31 to 0, dont check PG dropped fault.
5-2-11. Motor parameter [MOT]:b00-b22(0x0800-0x0816)
Factory
Setting
Change
Limited
b00
Motor 1 Rated
Frequency
0.00~Maximum frequency Hz 50.00 Y
b01 Motor 1 Rated Current y09*(50%~100%) A Y
b02 Motor 1 Rated Voltage 100~1140 V
Y
b03 Motor 1 Pole-pairs 1~8 - 2 Y
b04 Motor 1 Rated Speed 500~5000 rpm 1480
Y
b00~b04 are the motors nameplate parameters which touch the precision.Set the parameters
124

S
e
c
t
i
o
n

V

according to the motors nameplate.
b00 ~ b04 motor nameplate in parameters, it is necessary to re-calculate motor parameters by using
b11.
Excellent vector control performance requires exact motor parameters. Exact parameters are base
on the correct setting of motors rated parameters.
To assure the control performance, please match the right motor as per the inverters standard,
motor rated currents limited between 30%~120% of inverter rated current.
The rated current can be set, but cant be more than the rated current of the inverter. The parameter
confirms the OL protection capability of the motor and energy-saving running.
To prevent self-cooled motor form overheat when running in a low speed, and the motor capacity
change when motor character change little, the user can correct the parameter to protect the motor.
The number of motor pole pairs, such as the four pole motor, the number of pole pairs is set to 2
b05
Motor 1 N Load
Current
0.0~b01 A Y
b06
Motor 1 Stator
Resistance
0.000~30.000 ohm Y
b07
Motor 1 Rotor
Resistance
0.000~30.000 ohm Y
b08
Motor 1 Stator
Inductance
0.0~3200.0 mH Y
b09
Motor 1 Mutual
Inductance
0.0~3200.0 mH Y
b05~b09 can by input by motor actual parameters value, also can define motor parameter by b11
parameter measure function.and save automatically. If know the correct motor parameter, can input by
hand
When b11 is 1, 2, 3, the system calculates and measuresautomatically.
b05~b09 is the motors basic electric parameters, these parameters is essential to achieve vector
control calculation.
b10 Motor Selection
Motor 1 0
- 0 N
Motor 2 1
The system can select any group motor parameters.
Motor parameter measurements modify and save to corresponding motor parameter area
automatically.
b11
Motor Parameter
Measurement
No measurement 0
- 0 N
Set whether the measurement of electrical parameters in order to b10 motors choose motor 1 as an
example.
0 : N measurement
1 : Calculate by label data
According to the motor nameplate parameters b00 ~ b04 , automatic calculation b05 ~ b09 and
other electrical parameters,the advantage does not require power-on self - tuning,suitable for general
- purpose Y series of four pole motor, the other type motor can be adjusted based on this parameter.
2 : Inverter static measurement
3 : If the motor parameters can not be measured without load,you can choose static frequency converter
measurement. Make sure that motor in a static status ,after static measurement, it can be manually
adjusted some parameters, optimal control.
125

S
e
c
t
i
o
n

V

4 : The b11 is set to 2, the inverter automatically start parameter determination.
Keyboard figures area show "-RUN": waiting to run the command, start the measurement.
Keyboard figures area show "CAL1", inverter without output.
Keyboard figures area show "CAL2", inverter with output, static state.
Keyboard figures area show "-END": measuring ends.
Keyboard figures area show "E. CAL": the measurement process errors.
Process can be measured through the STOP key to stop.
3 : Inverter rotation measurement
Motor can be measured without load, can choose the rotation measurement. Measurements started,
make sure the motor is static.
Static measurement converter, the output DC voltage, pay attention to safety.
The b11 is set to 3, the inverter automatically start parameter determination.
Keyboard figures show that the regional show "-RUN": waiting to run the command, start the
measurement.
Keyboard figures area show "CAL1", "CAL3": N output inverter.
Keyboard figures area show "CAL2", inverter with output, under static state.
Keyboard figures area show "CAL4", inverter with output, the motor forward in high-speed.
Keyboard figures area show "-END": measuring the end.
Keyboard figures area show "E. CAL": the measurement process errors.
Process can be measured through the STOP key to stop.
Set this parameter,the motor parameters will be determined dynamically.Be sure the motor is
without load (N-load operation).
Before setting,be sure to run well prepared,the motor will run in high speed during the measurement
Measurement is completed, b11 return to 0. The measured parameters will select parameters on the
base of b10 motor parameters which is automatically saved to the b05 ~ b09 or b18 ~ b22.
Note: Before auto-measure the motor parameter, must input motor rated parameter b00~b04or
b13~17 correctly
Please regulate accelerating and deceleration time or torque increasing parameter, if there is over -
current or over voltage faults while auto- measurement.
When automatic regulation, motor should be in stop status.
b12
Vector Control initial
Inspection R1
Not inspection R1 0
- 0 N
Inspection R1 1
b13
Motor 2 Rated
Frequency
0.00~Maxmum frequency Hz 50.00 Y
b14 Motor 2 Rated Current y09*(50%~100%) A Y
b15 Motor 2 Rated Voltage 100~1140 V Y
b16 Motor 2 Pole Pairs 1~8 - 2 Y
b17 Motor 2 Rated Speed 500~5000 rpm 1480 Y
b18 Motor 2 N Load Current 0.0~b14 A Y
b19
Motor 2 Stator
Resistance
0.000~30.000 ohm Y
b20
Motor 2 Rotator
Resistance
0.000~30.000 ohm Y
b21
Motor 2 Stator
Inductance
0.0~3200.0 mH Y
b22
Motor 2 Mutual
Inductance
0.0~3200.0 mH Y
The 2nd group motor parameters can be set by system. The definition is same with group 1.
126

S
e
c
t
i
o
n

V

5-2-12. System parameter [SYS]:y00-y17(0x0900-0x0911)
Factory
Setting
Change
Limited
y00
Reset System
Parameter
No action 0
- 0 N
keyboard storage1
1
keyboard storage 2
2
keyboard storage 3
3
keyboard storage 4
4
factory set value
5
0 : No action
1 : Reset system parameter with keyboard storage 1
5 : Reset system parameter with factory set value
When this parameter set valid, all the function parameter reset to factory setting. The parameters
without factory setting will save the previous setting value.
y01
Parameter Upload To
Keyboard
No action 0
- 0 N
1
2
3
4
Clear up keyboard memory
area 1, 2, 3, 4
5
0 : No action;
1 : Reset system parameter with keyboard memory area1;
5 : Clear up keyboard memory area 1, 2, 3, 4
y02 Lastest Fault record Lastest fault record number mH 0 Y
y03 Fault Record 1
Press [PRG]and [/] key the
frequency, crrent and running status of
fault time can be known.
- 0 Y
y04 Fault Record 2
y05 Fault Record 3
y06 Fault Record 4
y07 Fault Record 5
These parameters register fault which happen in the last several times, and can inquire about the
value of monitor object at the time of fault by PRG and plus or minus key.
127

S
e
c
t
i
o
n

V

The monitor object of fault state:
0: Fault type
The fault code is expressed as following:
Serial number LED display Fault
0 E.OCP System is disturbed or impacted by instant over current
1 Reserved
2 E.OC3 Over current or over voltage signal from drive circuit.
3 Reversed
4 E.OU Over voltage
5 E.LU Under voltage
6 E.OL Over load
7 E.UL Under load warm
8 E.PHI Power input Phase loss
9 E.EEP EEPROM error
10 E.ntC Over heat
11 E.dAt Time limit fault
12 E.Set External fault
13 Reserved
14 Reserved
15 Reserved
16 E.PID PID regulate fault
17 E. OHt Motor over heat fault
18 E.OL2 Motor over load fault
19 E.PG PG fault
20 E.Pho Inverter output phase-lost
21 E.COA RS485 communication terminal A failure
22 E.Cob RS485 communication terminal B failure
23 E.CAL
Parameter identification problems.
1: set frequency at the time of fault
The output frequency of the inverter at the time of fault
2: output frequency at the time of fault
The output frequency of the inverter at the time of fault
3: output current at the time of fault
The actual output current at the time of fault
4: output DC voltage at the time of fault
The actual output voltage at the time of fault
5: Running state at the time of fault
The running state at the time of fault
LEDdisplay is below:
the first LED tthhte The second LED The third LED the fourth LED
F forward F forward status separator A accelerating
128

S
e
c
t
i
o
n

V

command
R
Reverse
command
R Reverse status D deccelerating
S Stop command S Stop status
E
running in a
even speed
S Stop status
6: running time at the time of fault
The running time at the time of fault
7: Inverter IGBT temperature at the time of fault
Inverter IGBT temperature
y08 Fault Record Reset
No action 0
- 0 Y
Reset 1
0 : No action, the fault records retains
1 : the fault records resets
y09 Rated Output Current 0.1~1000.0 A N
Inverter rated output current.
y10 Rated Input Voltage 100~1140 V N
The rated input voltage of the inverter. It would be set as per inverter input voltage level before
leaving factory.
y11 Product Series
80 0 3
- N
Family
code
Product
serial
Input oltage
grade 1
Product series (set according to family code/product serial/voltage grade)
80 0 3
family code
808000 serial
818100 serial
series number input voltage level
0: Flow load (F)
1:General load (G)
2: Middle load (M)
3: Heavy load (H)
6: TEXDRIVE (S)
7: WINDLASS (T)
8:JETDRIVE (Z)
1: single phase 220V
2: three phase 220V
3: three phase 380V
4: three phase 460V
5: three phase 575V
6: three phase 660V
9: three phase 1140V

y12 Software Version - - - N
version number
A:official version
B:specialized version
C:beta version

y13 Product Date-- Year YYYY - - N
y14
Product Date
-Month/Day
MMDD - - N
y15 User Decode Input
0~9999 Set range
- - Y Record password
wrongly input times
Display info
In the state of locked parameter,LED displays the times of error input. There are three input limit,if
input is wrong in continuous three times , the systems will prohibit input of the password . It can prevent
129

S
e
c
t
i
o
n

V

testing password in an illegal way, and need restart the machine to input again.
Once the input is right in any time during three times input limit, the parameter is unlocked.
y16 User password key-in
0~9999 Set range
- - Y
No password or
decode input is
correct
code
Display info
Parameter lock-in code
The parameter sets the password , and the range is 0 ~ 9999 . After setting the password , parameter
locks and keyboard displays code; if the password is unlocked or password input is right, the keyboard
will display deco.
Set password to 0, reset user password set, after re-electrify status is decode.
y17
Parameter Group
Protection
Corresponding parameter group
protection after set password
Set to 0: change is not allowed
Set to 1: change is allowed
- 0000 Y
y group
b group
9 8
2 2
8 9 7 6 5 4 3 2 1 0
2 2 2 2 2 2 2 2
0 1 2 3 4 5 6 7
F group
A group
o group
H group
U group
P group
E group
C group

130

S
e
c
t
i
o
n

V
I

Section VI. Fault Diagnosis & Solutions
6-1. Problems and solutions
Problems Possible causes Solutions
Keyboard can
not control
Running control mode setting is wrong Check F05
Frequency setting is wrong
Check F03F04
Potentiometer
cant regulate
speed
Control mode setting is wrong Check F05
Frequency setting is wrong
Check F03F04
The motor
Does not
rotate
LED monitor dislay fault
Press RESET or terminal for fault reset,
learn and fix the fault according to the
fault info
No voltage in terminals DC+1 and DC+2
Check the voltage at R, S or T and
charging circuit.
U, V or W terminals produce No output
or abnormal output.
Check the control mode and frequency
parameter. Check the terminal condition
if it is operated by an external terminal.
Re-start after powering down or free run
Remember the set operating state.
Too much load on the motor
Check the load condtion, and confirm
the model selection is right
Ove rcurrent
E.OC
Fault display E.OCP
System is disturbed or instant over
current
Fault display E.OC3
Motor over current, protect action when
motor actual current is 3 times over than
the motor rated current
Over current during acceleration Reset or adjust F09, F20, F21.
Over current during deceleration
Reset or adjust F10, F22, F23.
During starting, the low-frequency jitter
over-current
Modify F06 setting
Over current during operation
Check the load change and eliminate it.
Over current during starting or operation
sometime
Check if there is slight short circuit or
grounding.
Disturbance
Check the earthing wire, screened cable
grounding and terminals.
Over load
E.OL
Too much load
Lower the load.or enlarge b04, b14 in
the allowable load range or enlarge A24
to raise the thermal protection level.
Inappropriate parameter is set
Modify b04b14 in case of the motor
over -load allowed
Over voltage
E.OU
Power voltage exceeds the limit
Check voltage is right or not.
Frequency inverter rated voltage setting
is Y or N.
Too fast deceleration Modify F10.
Section VI Fault Diagnosis & Solutions
131

S
e
c
t
i
o
n

V
I
.

The load has too much inertia
Reduce the load inertia, or raise the
capacity of frequency converter, or add a
braking resistor.
Low voltage
E.LU
Too low power voltage
Checking voltage is normal or not.
Frequency inverter rated voltage setting
is Y or N.
Power off transiently
Add options of capacitor boxes.
The line has too small capacity or great
rush current exists on the lines.
Make renovation on power supply
system.
Over heat
E.OHt
Too high ambient temperature Improve ambient conditions
Cooling fans do not work.
Check A27, reduce fan starting
tamperaturer(when there is fan control)
The carrier frequency is too high
Check the setting value of function F16
Note:
Switch off the power supply, and do not touch the PCBs and any parts inside in five minutes after
the charging indicator light (CHARGE) goes off. Ensure the capacitance has been discharged
completely by measuring with the instrument before work inside. Otherwise, there is a danger of
electric shock.
Do not touch the PCB or IGBT and other internal parts unless actions have been taken to prevent
the static electricity. If not, the components may be damaged.

132

S
e
c
t
i
o
n

V
I
I

Section VII Standard Specifications
7-1. Specification
7-1-1. PI8000 Specification
Inverter
type
Light Load
F
Standard Load
G
Medium Load
M
Heavy Load
H Structure
item PF
kW
IF
A
PG
kW
IG
A
PM
kW
IM
A
PH
kW
IH
A
3 phase voltage 380V 50/60Hz
PI80003 15 32 11 25 7.5 16 8N2
PI80003 18.5 38 15 32 11 25 7.5 16 8N2
PI80003 22 45 18.5 38 15 32 11 25 8N3
PI80003 30 60 22 45 18.5 38 15 32 8N3
PI80003 37 75 30 60 22 45 18.5 38 8N4
PI80003 45 90 37 75 30 60 22 45 8N4
PI80003 55 110 45 90 37 75 30 60 8N5
PI80003 75 150 55 110 45 90 37 75 8N5
PI80003 93 170 75 150 55 110 45 90 8N6
PI80003 110 210 93 170 75 150 55 110 8N6
PI80003 132 250 110 210 93 170 75 150 8N7
PI80003 160 300 132 250 110 210 93 170 8N7
PI80003 187 340 160 300 132 250 110 210 8N8
PI80003 200 380 187 340 160 300 132 250 8N8
PI80003 220 415 200 380 187 340 160 300 8N9
PI80003 250 470 220 415 200 380 187 340 8N9
PI80003 280 520 250 470 220 415 200 380 8N9
PI80003 200 380 200 380 187 340 160 300 8NA
PI80003 220 415 220 415 200 380 187 340 8NA
PI80003 250 470 250 470 220 415 220 380 8NA
PI80003 315 600 280 520 250 470 220 415 8NB
PI80003 355 640 315 600 280 520 250 470
8NB
PI80003 400 690 355 640 315 600 8NB
PI80003 450 740 400 690
8NB

133

S
e
c
t
i
o
n

V
I
I

7-1-2. PI8100 Specification
Inverter type
Light Load
F
Standard Load
G
Medium
Load M
Heavy Load
H Structure
item PF
kW
IF
A
PG
kW
IG
A
PZ
kW
IZ
A
PH
kW
IH
A
Single phase voltage 220V 50/60Hz
PI81001 0.75 4 0.4 2.5 7N2
PI81001 1.5 7 0.75 4 0.4 2.5 7N2
PI81001 1.5 7 0.75 4 0.4 2.5 7N2
PI81001 2.2 10 2.2 10 1.5 7 0.75 4 7N3
PI81001 4 16 4 16 2.2 10 1.5 7 7N3
PI81001 5.5 20 5.5 20 4 16 2.2 10 7N4
PI81002 0.75 4 0.4 2.5 7N2
PI81002 1.5 7 0.75 4 0.4 2.5 7N2
PI81002 1.5 7 0.75 4 0.4 2.5 7N2
PI81002 2.2 10 2.2 10 1.5 7 0.75 4 7N3
PI81002 4 16 4 16 2.2 10 1.5 7 7N3
PI81002 5.5 20 5.5 20 4 16 2.2 10 7N4
PI81003 0.75 2.5 0.75 2.5 0.75 2.5 0.75 2.5 7N2
PI81003 1.5 3.7 1.5 3.7 1.5 3.7 1.5 3.7 7N2
PI81003 2.2 5 2.2 5 2.2 5 2.2 5 7N2
PI81003 4 8.5 4 8.5 4 8.5 4 8.5 7N3
PI81003 5.5 13 5.5 13 5.5 13 7N3
PI81003 7.5 16 7.5 16 7.5 16 5.5 13 7N4
PI81003 11 25 7N4
134

S
e
c
t
i
o
n

V
I
I

7-1-3. Table of rated current for different specifications
G/F/H/S/Z/T/M
Votage
220V
1
220V
(240V)
380V
(415V)
460V
(440V)
575V 660V
Power
(kW)
Current
(A)
Current
(A)
Current
(A)
Current
(A)
Current
(A)
Current
(A)
0.4 2.5 2.5 - - - -
0.75 4 4 2.5 2.5 - -
1.5 7 7 3.7 3.7 - -
2.2 10 10 5 5 - -
4 16 16 8.5 8 - -
5.5 - 20 13 11 - -
7.5 - 30 16 15 - -
11 - 42 25 22 17 15
15 - 55 32 27 22 18
18.5 - 70 38 34 26 22
22 - 80 45 40 33 28
30 - 110 60 55 41 35
37 - 130 75 65 52 45
45 - 160 90 80 62 52
55 - 200 110 100 76 63
75 - 260 150 130 104 86
93 - 320 170 147 117 98
110 - 380 210 180 145 121
132 - 420 250 216 173 150
160 - 550 300 259 207 175
187 - 600 340 300 230 198
200 - 660 380 328 263 218
220 - 720 415 358 287 240
250 - - 470 400 325 270
280 - - 520 449 360 330
315 - - 600 516 415 345
355 - - 640 570 430 370
400 - - 690 650 520 430
450 - - 740 700 600 490
500 - - 860 800 650 540
135

S
e
c
t
i
o
n

V
I
I

7-2. Standard specification
Items Specifications
Power
Voltage and
frequency
Single-phase 200~240V, 50/60Hz
Three-phase 200~240V, 50/60Hz
Three-phase 575V, 50/60Hz
Three-phase 660V, 50/60Hz
Three-phase 1140V, 50/60H
Allowable
Fluctuation range
voltage: 15% frequency: 5%
Control
Control system high performance vector control inverter based on 32 bit DSP
Output frequency
G/F/Z/S/T/M type: 0.00~400.0Hz, maxmum frequency can be set
between 10.00 and 400.0Hz

control method V/Fcontrol
Sensorless vector
control
Sensor close loop
vector control
Start torque 0.50Hz 180% 0.25Hz 180% 0.00Hz 180%
speed adjustable
range
1: 100 1: 200 1: 2000
Speed stabilizing
precision
0.5% 0.2% 0.02%
waveform produce
methods
Asynchronous space vector PWM, N-class sub-synchronous space
vector PWM, two-phase optimization of space vector PWM.
Auto torque boost
function
Achieve low frequency (1Hz) and high output torque control under
V.F control mode.
Accelerate
/decelerate control
Sub-set S curve acceleration and deceleration mode, maximum
acceleration and deceleration time is 3200 days
Long running time
control
16 segments speed run, maximum running time is 3200 days
frequency setting
accuracy
Digit: 0.01Hz(below 300Hz), 0.1Hz(above 300Hz);
alalogue: 1% of maxmum frequency
frequency accuracy Speed control tolerance 0.01%(2510).
V/F curve mode
Linear, 1.2 times the power, 1.7 times the power, 2 times power,
user-set 8 V / F Curve.
Over load
capability
G / S type: 150% rated current -1 minute, rated current 200% -0.1
second;
F: rated current 120% -1 minute 150% of rated current -0.1
second;
Z / M / T type: rated current 180% -1 minute 250% rated current
-0.1 second;
H: rated current 250% -1 minute 300% rated current -0.1 second.
slip compensation V / F control can automatically compensate for deterioration.
Running
Running method Keyboard/terminal/communication
Starting signal
Forward, reverse, jog (parameter control direction), forward jog,
and reverse jog.
136

S
e
c
t
i
o
n

V
I
I

Emergency stop Interrupt controller output.
fault reset
When the protection function is active, you can automatically or
manually reset the fault condition.
Running status
Motor status display, stop, acceleration and deceleration, constant
speed, the program running.
DC brake
Built-in PID regulator brake current flow in the premise, however,
to ensure adequate braking torque.
Protection
Inverter protection
Overvoltage protection, undervoltage protection, overcurrent
protection, overload protection, over-temperature protection, over
the loss of speed protection, over-voltage stall protection, phase
protection (optional), external fault, communication error, PID
feedback signal abnormalities, PG failure
IGBT temperature
desplay
Display current IGBT temperature
Inverter fan control The fan starting temperature can be set(optional)
Instant power-down
re-start
Less than 15 milliseconds: continuous operation.
Greater than 15 milliseconds: Automatic detection of motor speed,
instantaneous power-down re-start.
Speed starting track
method
automatically track motor speed when inverter starts
Parameter
protection function
Protect inverter parameters by setting the password and decoding
IO
8 way switch input
Can be customized into 68 kinds of functions, to achieve forward,
reverse, forward jog, and reverse jog, emergency stop, reset, speed,
acceleration speed, run-time switch, and pulse counting.
3 way analog inputs
Can be defined as a switch input;
To allow for maximum input range-10V ~ +10V, 0 ~ 20mA
2 way anolog
output
Can achieve output range 0 ~ +10V, 0 ~ 20mA
Virtual terminal
function
Can be set to a virtual terminal, using communication or keyboard
IO port, and with the IO port status display.
Keyboard
Frequency set
In 6 main ways + to 7 kinds of auxiliary to the way of the keyboard,
three way analog input, pulse input, digital potentiometers.
Keyboard cable 8-core cable, in line with EIA T568A, EIA T568B standards.
Double keyboard
port
Supports dual-keyboard, synchronous control, independently of
each other.
Double and multi
function keys
MF1, MF2 can be customized as addition and subtraction, forward,
reverse, forward jog, and reverse jog, emergency stop, rise and fall,
and other 9 kinds of ways.
4-parameter storages
Control panel can be realized four groups of inverter parameters of
upload, download, with manufacturer password to reset factory
setting.
Running info At most display 3 monitoring parameters. Select by A00, A01, A02
Fault info
Store 5 groups error messages at most, you can check the type of
failure time when failure occurrs, set frequency, output frequency,
output voltage, output current, running state, running time, IGBT
temperature.
Commu- Double RS485 port Rs485 port and an optional keyboard completely isolated RS485
137

S
e
c
t
i
o
n

V
I
I

nication communication module.
CAN BUS Can select can-bus module.
Speed
16-segment speed
At most 16 segments can be set (use multi-functional terminal to
shift or program runs).
8-segment running
time
At most8segment running time can be set(multi-functional terminal
can be used to shift)
8 segment
acceleration speed
At most 8 acceleration speed(can use the multi-functional terminal
to switch).
Seven-Segment
Speed
Configuration
At most 7 segment speed configuration can be set
(multi-functional terminal can be used to switch).
PID
PID feedback signal
Six kinds of ways, keyboard, three way analog input, pulse input,
digital potentiometers.
PID giving signal
Six kinds of ways, keyboard, three wayl analog input, pulse input,
digital potentiometers.
Motor
2 goups of motor
parameters
With the motor parameters, parameter can be selected, parameter
identification automatic storage.
3 identification
method
Name plate calculation, static measurement, rotation measurements.
5 name plate
parameters
Rated frequency, rated current, rated voltage, the number of pole
pairs, rated speed.
5 indentification
parameters
N-load current, stator resistance, rotor resistance, stator inductance,
mutual inductance.
Environ-
ment
Environment
temperature
-10 ~ 40, 40 ~ 50 derating between the use is increased by
1 , rated output current decrease of 1%.
Store temperature -40~+70
Environment
humidity
5~ 95 %, No condensation
Heightvibration
0 ~ 2000 meters, 1000 meters above derating use, increased by 100
m, rated input decreased%
Application
location
Mounted vertically inside the control cabinet with good ventilation,
do not allow the level , or other installation method . The cooling
medium is air. Installed in the absence of direct sunlight, N dust, N
corrosive and explosive gas, N oil mist, N steam, N drip
environment
Cooling method Forced air cooling and natural air cooling.
138

S
e
c
t
i
o
n

V
I
I

7-3. Sharp Size
7-3-1. PI8000 family (3 phase voltage 380~415V, 50/60Hz)
1. 8N2~8N9
W
b
d
aL
H

1) 8N2
Type
Power
(kW)
Structure
item
Shape Installation dimension
L W H a b d
F 15~18.5
8N2 380 220 230 360 135 10
G 11~15
M 7.5~11
H 7.5
2) 8N3
Type
Power
(kW)
Structure
item
L W H a b d
F 22~30
8N3 460 280 245 440 160 10
G 18.5~22
M 15~18.5
H 11~15
3) 8N4
Type
Power
(kW)
Structure
item
L W H a b d
F 37~45
8N4 500 300 270 480 200 10
G 30~37
139

S
e
c
t
i
o
n

V
I
I

M 22~30
H 18.5~22
4) 8N5
Type
Power
(kW)
Structure
item
L W H a b d
F 55~75
8N5 630 360 297 610 200 10
G 45~55
M 37~45
H 30~37
5) 8N6
Type
Power
(kW)
Structure
item
L W H a b d
F 93~170
8N6 700 400 297 680 200 10
G 75~93
M 55~75
H 45~55
6) 8N7
Type
Power
(kW)
Structure
item
L W H a b d
F 132~160
8N7 750 475 320 730 260 10
G 110~132
M 93~110
H 75~93
7) 8N8
Type
Power
(kW)
Structure
item
L W H a b d
F 187~200
8N8 850 500 320 830 260 10
G 160~187
M 132~160
H 110~132
8) 8N9
Type
Power
(kW)
Structure
item
L W H a b d
F 220~250~280
8N9 1000 600 380 940 370 14
G 200~220~250
M 187~200~220
H 160~187~200
140

S
e
c
t
i
o
n

V
I
I

2. 8NA
a
Muro di sostegno del
foro di montaggio

Type
Power
(kW)
Structure
item
L W H a b d
F 200~220~250
8NA 1540 515 443 465 367 13
G 200~220~250
M 187~200~220
H 160~187~220
141

S
e
c
t
i
o
n

V
I
I

3. 8NB
bottom board
bottom entry
back entry
H
d
a
b
L
W

Type
Power
(kW)
Structure
item
L W H a b d
F 315~355~400~450
8NB 1700 850 492 640 260 13
G 280~315~355~400
M 250~280~315
H 220~250
142

S
e
c
t
i
o
n

V
I
I

7-3-2. PI8100 Family
1. 7N2~7N4
1) 7N2
PRG
FWD MF2 MF1
ESC STOP/RESET
SET
DIGITAL PANEL
+
-
+
E
N
T
E
R
ALARM
V
A
Hz
s
%
C
-
FWD REV
S00
0.00 0.0
S01
S10 PID

Power type Type
Power
(kW)
Single phase
220V
F 0.75~1.5
G 0.4~1.5
M 0.4~0.75
H 0.4
3 phase
220V
F 0.75~1.5
G 0.4~1.5
M 0.4~0.75
H 0.4
3 phase
380V
F 0.75~1.5~2.2
G 0.75~2.2
M 0.75~2.2
H 0.75~2.2
143

S
e
c
t
i
o
n

V
I
I

2) 7N3
PRG
FWD MF2 MF1
ESC STOP/RESET
SET
DIGITAL PANEL
+
-
+
E
N
T
E
R
ALARM
V
A
Hz
s
%
C
-
FWD REV
S00
0.00 0.0
S01
S10 PID

Power type Type
Power
(kW)
Single phase
220V
F 2.2~4
G 2.2~4
M 1.5~2.2
H 0.75~1.5
3 phase
220V
F 2.2~4
G 2.2~4
M 1.5~2.2
H 0.75~1.5
3 phase
380V
F 4~5.5
G 4~5.5
M 4~5.5
H 4
144

S
e
c
t
i
o
n

V
I
I

3) 7N4
PRG
FWD MF2 MF1
ESC STOP/RESET
SET
DIGITAL PANEL
+
-
+
E
N
T
E
R
ALARM
V
A
Hz
s
%
C
-
FWD REV
S00
0.00 0.0
S01
S10 PID

Power type Type
Power
(kW)
Single phase
220V
F 5.5
G 5.5
M 4
H 2.2
3 phase
220V
F 5.5
G 5.5
M 4
H 2.2
3 phase
380V
F 7.5~11
G 7.5
M 7.5
H 5.5
145

S
e
c
t
i
o
n

V
I
I

7-3-3. Keyboard size
JP6C8000:
DIGITAL PANEL
FWD REV ALARM
+
-
Hz
A
V
%
s
E
N
T
E
R
PRG
ESC
MF1 MF2 FWD
SET
STOP/RESET
+
-

JP6E8000:
DIGITAL PANEL
FWD REV ALARM
+
-
Hz
A
V
%
s
E
N
T
E
R
PRG
ESC
MF1 MF2 FWD
SET
STOP/RESET
+
-

146

S
e
c
t
i
o
n

V
I
I

JP6D8000 the dimension of keyboard rabbet:

the dimension of aperture for installing keyboard in panel
75.50.1*122.50.1

147

S
e
c
t
i
o
n

V
I
I
I

Section VIII. Maintenance
8-1. Inspection and Maintenance
Under normal working conditions, in addition to daily inspection, the frequency converter should be
subject to regular inspection (for example inspection for overhaul or as specified but at an interval of six
months at most). Please refer to the following table in order to prevent faults.
Check
time
Check
point
Check item Check to be done Method Criterion
D R
Display
LED and OLED
display
If there is any
abnormal display
Visual check
As per use
state

Cooling
system
Fan
If abnormal noise or
vibration is produced.
Visual and
audible check
N abnormal
sound or
vibration
Body
Surrounding
conditions
Temperature,humidity,
dust content, harmful
gas, etc.
Check visually,
by smelling and
feeling
As per Section
2-1

Input/
output
terminal
Voltage
If input, output voltage
is abnormal
Measure at
R, S, T and U, V,
W terminals
As per standard
specifications

Main
circuit
Overall conditions
If the fastenings come
loose, if any signs show
overheat,discharging, or
too high dust content, or
the air piping is blocked
Check visually,
tighten the
fastenings, and
clean the related
parts
N abnormal
conditions
Electrolytic
capacitance
If there is abnormal
appearance
Check visually
N abnormal
condition
Current-conducting
leads or blocks
If the parts come loose Check visually
N abnormal
condition
Terminals
If the screws or bolts
come loose
Tighten the loose
screws or bolts
N abnormal
condition
D means daily check and R means regularly check.
means need daily check or regularly check
For inspection, do not disassemble or shake the parts without reason, and still less pull off the
plug-in-parts at random. Otherwise, the unit will not operate normally, or can not enter the mode of fault
display, or causes faults of components or even parts of the main switch components IGBT module is
damaged.
If measuring is necessary, the user should note that much different results will be gained possibly if
the measuring is performed with different instruments. It is recommended that the input voltage be
measured with pointer-type voltmeter, output voltage with rectification voltmeter, input and output
current with tong-test ammeter, and power with electrically-driven wattmeter.
8-2. Periodically-Replaced Parts
In order to ensure the operation reliability of the frequency converter, in addition to regular
maintenance and inspection, all the parts suffering long-term mechanical wear should be replaced at a
regular interval, which includes all cooling fans and the filtering capacitors of main circuits for energy
buffer and interchange and PCBs. For continuous use under normal conditions, these parts can be
replaced according to the following table and the operating environment, loads and the current state of
frequency converter.
Section VIII Maintenance
148

S
e
c
t
i
o
n

I
X

Part name Interval for replacement
Cooling fan 1~3 years
Filtering capacitor 4~5 years
PCB (printed circuit board) 5~8 years
8-3. Storage
The following actions must be taken if the frequency converter is not put into use immediately after
delivery to the user and need to keep well for the time being or stored for a long time:
Stored in a dry and adequately-ventilated place without dust and metal powder at the temperature
specified in the specifications.
If the frequency converter is not put into use after one year, a charge test should be made, so as to
resume the performance of the filtering capacitor of main circuit in it. For charging, a voltage
regulator should be used to slowly increase the input voltage of the frequency converter until it
reaches the rating, and the charge should last more than 1~2 hours. This test should be made at
least once a year.
Dont perform breakdown test at random, for this test will cause shorter life of the frequency
converter. The insulation test must be performed after the insulation resistance is measured with a
500-volt megaohm and this value must not be less than 4M.
8-4. Measuring and Judgment
If the current is measured with the general instrument, imbalance will exists for the current at the
input terminal. Generally, differing by not more than 10% is normal. If it differs by 30%, inform
the factory to replace the rectification bridge, or check if the error of three-phase input voltage is
above 5V.
If the three-phase output voltage is measured with a general multi-meter, the reading is not
accurate due to the interference of carrier frequency and only for reference.

149

S
e
c
t
i
o
n

I
X

Section IX. Options
The series can acquire the peripheral equipment by user because of the different using condition and
requirement. See the wiring diagram as below:

9-1. MCCB OR ELCB
As power switch of the inverter, MCCB or ELCB can protect supply power, but cant control
inverter to run or stop.
9-2. AC reactance
AC reactance is able to restrain the high harmonic wave of converter input current and improve
converters power factor obviously. Its recommended that AC reactance will be used in the following
condition:
Section IX Options
150

S
e
c
t
i
o
n

I
X

The capacity of power source is ten times more than the capacity of converter.
SCR load or power factor compensated device with ON/OFF is connected with the same power
supply.
Unbalanced 3-phase voltage is bigger (more than 3%).

The common size of AC input reactance:
W
Z
Y
V
X
U
E
F

Sharp size:
Inverter standard Size (mm) Gross
Weight
(kg)
Voltage
Capacity
(kW)
A B C D E F
200V
230V
0.75 155 125 95 7 89 60 3.0
1.5 155 125 95 7 89 60 3.0
2.2 155 125 95 7 89 60 3.0
4 155 125 95 7 89 60 3.5
5.5 155 125 100 7 89 60 3.5
7.5 155 125 112 7 89 70 4.0
11 155 125 112 7 89 70 6.0
15 180 140 112 8 90 80 8.0
18.5 180 140 112 8 90 90 8.0
22 180 140 112 8 90 90 8.0
30 230 175 122 10 160 90 12.0
37 230 175 132 10 160 100 15.0
45 230 175 150 10 160 110 23.0
55 230 175 160 10 160 120 23.0
75 285 220 230 14 180 130 30.0
380V
460V
0.75 155 125 95 7 89 60 3.0
1.5 155 125 95 7 89 60 3.0
2.2 155 125 95 7 89 60 3.0
4 155 125 95 7 89 60 3.5
Section IX Options
151

S
e
c
t
i
o
n

I
X

5.5 155 125 100 7 89 60 3.5
7.5 155 125 112 7 89 70 4.0
11 155 125 112 7 89 70 6.0
15 180 140 112 8 90 80 8.0
18.5 180 140 112 8 90 90 8.0
22 180 140 112 8 90 90 8.0
30 230 175 122 10 160 90 12.0
37 230 175 132 10 160 100 15.0
45 230 175 150 10 160 110 23.0
55 230 175 160 10 160 120 23.0
75 285 220 230 14 180 130 30.0
110 285 250 230 14 210 140 33.0
160 360 260 230 14 210 140 40.0
200 360 270 230 14 210 140 45.0
250 400 330 240 14 240 140 55.0
315 400 350 285 14 270 160 90.0
9-3. Noise filter
The filter is used to restrain the conduction of electrical magnetic wave interference noise produced
by the converter or shock the interferential form radio or momentary concussion. The common size of
3-phase EMI noise filter is shown as following: confirm the power supply is 3-phase three lines or
3-phase four lines or single phase. Earthling wire is as short as possible, try to place the filter near the
converter.
Please choose EMI filter when the converter is used in residential area, commercial area, science
area or other. Please need to prevent magnetic interference, or need meet CE, UL, and CSA standard.
Note: If needed the filter, please contact with our company.
9-4. Connector
It can cut off the supply power in action of the system protection function, to prohibit fault enlarging.
But cant control the motor start or stop by connector.
9-5. Braking Unit & braking resistor
There is braking unit inside when using B type frequency converter, the maximum braking torque
is 50%. Please choose braking resistor according to the following table:
Type
Converter power
(kW)
Braking resistor
()
Braking resistor
Power (W)
220V
0.75 200 120
1.5 100 300
2.2 70 300
4 40 500
5.5 30 500
7.5 20 780
Section IX Options
152

S
e
c
t
i
o
n

I
X

11 13.6 2000
15 10 3000
18 8 4000
22 6.8 4500
380V
0.75 750 120
1.5 400 300
2.2 250 300
4 150 500
5.5 100 500
7.5 75 780
11 50 1000
15 40 1500
Please choose POWTRAN BRAKING UNIT if you need more braking torque. Please refer to the
catalog of braking unit.
There is N braking unit inside the large capacity frequency converter. Please choose POWTRAN
BRAKING UNIT if you need braking.
9-6. output EMI filter
The fittings can restrain the disturbance noise and lead leak current produced in the output side.
9-7. AC output reactor
When the line from inverter to motor is longer than 20 meters, it can restrain the over-current caused
by the distributing current and the wireless disturbance of the inverter.

153

S
e
c
t
i
o
n

X

Section X Quality Assurance
The product quality assurance is in accordance with the following regulations:
1. The manufacturer should take responsibility for below specific elements:
1-1. In domestic use (as calculated from the date of shipment)
shipped within one month should accept refund, replacement and repair.
shipped within three months should accept replacement and repair.
ship packages within 15 months should accept repair.
1-2. Goods exported overseas (excluding China) and shipped within six months, the local seller is
responsible for repair.
2. Regardless of when and where to use POWTRAN branded products are paid to enjoy lie-long
service.
3. All the distributors, agency or production place of POWTRAN in whole China can provide
after-sales service for powtarn product, their conditions of service as follows:
3-1. We provide a 3-level inspection service on the local selling place (including troubleshooting).
3-2. All services comply with the related after-sale service terms and conditions stated on the
agency agreement between powtran and distributors.
3-3. Buyers can pay to any Powtran agent if need any after-sales services (whether or not the
warranty).
4. If this product has some quality problem or product liability accidents, we will take the
responsibility to terms 1-1 or 1-2 at most. if users need more liability guarantee, please apply for
insurance company in advance to insure your own property insurance.
5. The products warranty period is one year from the date of shipment.
6. In the case of the following causes of failure, even in the warranty period is also a paid repair:
6-1. Incorrect operation (depending on the use of manual), or modified without permission to
repair the problems caused.
6-2. The problems caused by using the inverters beyond its standard specifications requirement.
6-3. Damage caused by drop down or improper handling.
6-4. Inverters components aged or failure caused by improper environment.
6-5. Due to an earthquake, fire, wind and water disasters, lightning, abnormal voltage or other
natural disasters and disasters, accompanied by the damage caused.
6-6. The damage during transport (Note: The mode of transport designated by the customer, the
company's help on behalf of the procedures for handling the transfer of goods).
6-7. When the manufactures brand, trademark, serial number, nameplate and other damage or can
not be recognized.
6-8. If the buyer has not paid full money according to purchase agreement.
6-9. The installation, wiring, operation, maintenance or other use of objective reality can not be
described to the company's service office.
7. Concerning refund, replacement and repair services, goods shall be returned powtran company,
after confirmed the attribution of responsibility then they are allowed to be returned or repaired.

154

A
p
p
e
n
d
i
x

I

Appendix I. RS485 Communication Protocol
I-1. Use introduce
This chapter introduces something about the install and handle of RS485 communication between inverter
and PLC, PC, factory computer.
RS485 standard interface
Can communicate with all computer
Using multi-drop link system, can link more to 127 inverters
Completely isolated, and noise shield
The user would use all types of RS232-485 inverter, if only the inverter had automatic RTS
control function inside.
I-2. Specification
Communication function
Items Specification
Communication baud rate 38400/19200/9600/4800/2400/1200 bps is selectable.
Communication Protocol Modbus protocol, RTU format
Interface methods
Asynchronism communication methods, semi-duplex, the previous
high byte, low byte in the post, and low-effective-bit pre-emptive.
Data fumula 1 start bit, 8 data bits, 1 stop bit, invalid parity bit.
Slave address
Slave addresses can be set up 1~ 127
0 for broadcast address, host address 128 for the proportion of
linkage, other addresses are reserved.
Communication port A
Isolated RS485 Communication CardTerminals SG+, SG-
RS232 communication cardterminals TX232, RX232
Shield SH, Default 19200bps.
Communication port B RJ45, 8-core shielded cable, fixed 19200bps.
I-3. Communication connection
I-3-1. Definition for Communication port A:
RS485 communication module installation
Appendix I Rs485 Communication Protocol
155

A
p
p
e
n
d
i
x

I

8K-RS485_S connect to 8KLCB control board

8K-RS485_S connect to 8KSCB control board

Link RS485 communication cables to inverter control terminals (SG+), (SG-).
When using RS232-485 transform, connect Inverter SG+ to RS485 T+, Inverter SG- to
RS485 T-.
After Confirming connection again, turn on inverter power.
If connection is right, set communication parameters as following:
A29 baud rate 01200, 12400, 24800, 39600, 419200, 538400
156

A
p
p
e
n
d
i
x

I

A28 current inverter communication address 1~127 (If there are more than 1 inverters, dont use
the same number);
When using RS485 running control methods, set F04=0/1/2,choice RS485 running control method
PC
Match register
120ohm 1/4W
N# 2#
SG+ SG-
Inverter
1#
T-
T+
GND
RX
TX
RS485
converter
Inverter Inverter
SG- SG+ SG- SG+

I-3-2. Definition for Communication port B
Communication
port B pins
1 2 3 4 5 6 7 8
Communication
B port signal
GND +5V 485+ 485- 485+ 485- +5V GND
EIA/TIA T568A
White
green
green
White
orange
blue
white
Blue
orange
White
Brown
brown
EIA/TIA T568B
White
Orange
Orange
White
Green
Blue
White
Blue
green
White
Brown
brown

I-3-3. Data safety and reliability
The number of inverter can be connected is no more than 127.
Though the length of communication cable can add up to 1300m, considering the stability, the length
limit within 800m.
All the control signal cable use the shield cable, and is linked to the signal terminal SH of RS485.
Data packet using CRC (vertical lengthy test) frame detection to ensure data reliability.
Completely isolated RS485 communication module to ensure reliable communications, support
hot-swappable, after modular access, you can enter the work.
The system is tested in 6 kinds of baud rate: 0:1200, 1:2400, 2:4800, 3:9600, 4:19200, 5:38400
However, if under deteriorating environmental conditions, lowering the baud rate can improve the
communication quality.
Interval time of sending from frame to frame is more than 50 bytes.
I-4. Communication Protocol
Communication architecture is inverter as a slave, the computer as a host.
157

A
p
p
e
n
d
i
x

I

MODBUS protocol defines a simple protocol data unit (PDU) which has nothing to do with a basic
communication layer, Specific bus or network MODBUS protocol mapping can introduce some
additional domain from application data unit (ADU).

The basic format description
I-4-1: Start of frame, End of frame
Interval 3.5 bytes,
I-4-2: Slave Address
From the machine's local address, through the A28 parameter settings, one network can only one
local address uniquely identifed.
Setting range 1 ~ 127.
00H = 0 ID address is broadcast mailing address, 128 ~ 255 reserved.
I-4-3: Function Code
Host send commands, slave response.
Function Code Categories
0x03read inverterps multiple function codes, at most can read 16 registers(register pair of byte)
Host command
Frame start
address
Slave
address
Function
code
Registers
address
Register
number
CRC
checksum
frame end
address
Interval3.5bytes 1 byte 1 byte 2 bytes 2 bytes 2 bytes
Interval3.5
bytes
Slave response
Frame start
address
Slave
address
Function
code
Read
byte
Read content
CRC
checksum
frame end
address
Interval3.5bytes 1 byte 1 byte 1 byte
2 bytes*register
number
2 bytes
Interval3.5
bytes
Note: Read content=2 bytes x register number

0x06write inverter 1 function code
Host command
Frame start
address
Slave
address
Function
code
Registers
address
Register
data
CRC
checksum
frame end
address
Interval 3.5
bytes
1 byte 1 byte 2 bytes 2 bytes 2 bytes
Interval 3.5
bytes
Slave response
Frame start Frame end Address field Function code Data CRC checksum
PDU
ADU
158

A
p
p
e
n
d
i
x

I

Frame start
address
Slave
address
Function
code
Registers
address
Register
data
CRC
checksum
frame end
address
Interval3.5bytes 1 bytes 1 bytes 2 bytes 2 bytes 2 bytes Interval 3.5 bytes

0x10Write multiple function in inverter, at most can be written in 16 registers(register pair of
byte)
Host command
Frame start
address
Slave
address
Function
code
Register
address
Register
number
Register
content byte
Register
content
CRC
checksum
frame end
address
Interval3.5bytes 1 byte 1 byte 2 bytes 2 bytes 1 byte
2bytes*register
number
2 bytes Interval3.5bytes
Slave response
Frame start
address
Slave
address
Function code Register address
Register
number
CRC
checksum
frame end
address
Interval3.5bytes 1 byte 1 byte 2 bytes 2 bytes 2 bytes Interval3.5bytes

0x01=Read multiple switch status
Host Command
Frame start
address
Slave
address
Function
code
address Switch number
CRC
checksum
frame end
address
Slave response
Frame start
address
Slave
address
Function
code
Read byte
number
switch
state
CRC
checksum
frame end
address
Interval3.5bytes 1 byte 1 byte 1 byte(data N) N bytes 2 bytes Interval3.5bytes
Note: read byte number N=output quanlity/8, if the remainder is not 0, read byte number is N=N+1

0x05=Write single switch status
Host Command
Frame start
address
Slave
address
Function
code
Output address Output value
CRC
checksum
frame end
address
Note: output value 0xFF00, switch ON; output value 0x0000, switch OFF. Other values are illegal,
the switch does not work.
Slave response
Frame start
address
Slave
address
Function
code
Output
address
Output
value
CRC
checksum
frame end
address
159

A
p
p
e
n
d
i
x

I

If slave response and get back to below function code, it means communications abnormal.
0xA0 =0x80+0x20= Invalid operation, setting under this state is invalid
0xA1 =0x80+0x21= function code is invalid
0xA2 =0x80+0x22= Fault record is empty
0xA3 =0x80+0x23= register address is invalid
0xA4 =0x80+0x24= slave is busy, EEPROM delay.
0xA5 =0x80+0x25= administrator restricted
0xA6 =0x80+0x26= set value is beyond limit.
0xA7 =0x80+0x27= CRC checksum error
0xA8 =0x80+0x28= frame format error

I-4-4: Register Address:
The register address includes two bytes, data setting is constituted by a two-byte.
Function code Register Address high byte Register Address low byte
0x03read
inverter
multiple
function.code
parameter
Parameter group Parameter serial number
F 0x00 063
A 0x01 063
o 0x02 071
H 0x03 055
U 0x04 015
P 0x05 015
E 0x06 023
C 0x07 047
b 0x08 023
y NOTE 1 0x09 023
S 0x0B 015
0x03.read
inverter status
Status Status number
R 0x10
0x00 Running status NOTE 2
0x01 Reserved status 1
0x03read
inverter.fault
history record
Fault record Fault status history record content
Fault history record 1
0x20
0x21
0x22
0x23
0x24
0x00 Fault type NOTE 4
0x01 Set frequency
0x02 Actual frequency
0x03 Actual current
0x04 DC voltage
0x05 Running status NOTE 5
0x06 Running time
0x07 IGBT temperature
0x06.write
inverter.single
Register Address high byte Register Address low byte
Parameter group High byte Parameter serial number
160

A
p
p
e
n
d
i
x

I

function.code
parameter,
only write
RAM

0x10.write
inverter
multiple
function.code
parameter,
only write
RAM
data
F 0x00 063
A 0x01 063
o 0x02 071
H 0x03 055
U 0x04 015
P 0x05 015
E 0x06 023
C 0x07 047
b 0x08 023
y NOTE 1 0x09 023
0x06.write
inverter
command
Command Command number
R 0x10
0x00 Running command NOTE 3
0x01 Reserved command 1
Function parameter write EEPROM, register address high byte=original register address high byte+0x80
0x06.write
inverter.single
function.code
parameter

0x10.write
inverter
multiple
function code
parameter
Register address high byte Register address low byte
parameter Parameter serial number
F 0x80 063
A 0x81 063
o 0x82 071
H 0x83 055
U 0x84 015
P 0x85 015
E 0x86 023
C 0x87 047
b 0x88 023
y NOTE 1 0x89 023
0x01.read
multiple
switch status
0x05.Write
single.switch
status
Switch classify address Parameter value
Running status 0x00
0
Control
method
0 V/F control
1 SV control
1 reserved
2
Running
status
0 stop
1 run
3
Direction
status
0 reverse
1 forward
5,4
Speed up
status
00 stop
01 acceleration
10 deceleration
11 uniform speed
6 upper 0 Upper frequency
161

A
p
p
e
n
d
i
x

I

frequency not arrive
1 Arrive
7
Lower
frequency
0
lower
frequency
1 Arrive
8
JOG
running
0
No JOG
running
1 JOG running
9 Reserved
10 Reserved
11 Reserved
12
Fault
confirm
0 Confirmed fault
1
Unconfirmed
fault
13
Direction
status
0 No fault
1 alarming fault
14
JOG
status
0 No fault
1
Deceleration
stop fault
15
Fault
status
0 No fault
1
Urgent stop
fault
Input.terminal function 0x01
0 DI1 input
0 Invalid
1 Valid
1 DI2 input
0 Invalid
1 Valid
2 DI3 input
0 Invalid
1 Valid
3 DI4 input
0 Invalid
1 Valid
4 DI5 input
0 Invalid
1 Valid
5 DI6 input
0 Invalid
1 Valid
6 DI7 input
0 Invalid
1 Valid
7 DI8 input
0 Invalid
1 Valid
8 AI1 input
0 Invalid
1 Valid
9 AI2 input
0 Invalid
1 Valid
10 AI3 input
0 Invalid
1 Valid
162

A
p
p
e
n
d
i
x

I

Output.terminal function 0x02
0 O1 input
0 Invalid
1 Valid
1 O2 input
0 Invalid
1 Valid
2 O3 input
0 Invalid
1 Valid
3 O4 input
0 Invalid
1 Valid
Fault type 0x03
0 E.OCP
System is disturbed or
impacted by instant over
current,over current sig-
nal from current inspec-
ted circuit or drive circuit
1 reserved
2 E.OC3
Inverter output current
exceeded 3times the
motor rated current
3 reserved
4 E.OU Over voltage
6 E.OL Over load
7 E.UL Under load warming
8 E.PHI Phase loss
10 E.ntC Over heat
13 reserved
14 reserved
15 reserved
16 E.PId PID regulation fault
17 E.OHt
Motor over heat fault
19 E.PG PG error
20 E.PHo
Inverter output phase
loss
21 E.COA
Rs485.communication
port A fault
22 E.COb
Rs485.communication
port B fault
23 E.CAL
Parameter
indentification fault
Switch classify address Parameter number
Running status 0x00 0
Run
command
0 stop
1 run
163

A
p
p
e
n
d
i
x

I

1 reserved
2
Direction
command
0 reverse
1 forward
3 reserved
4 reserved
5
JOG
command
0 reverse
1 forward
6 reserved
7 Free stop
0 reverse
1 forward
8
reserved
9
reserved
10 reserved
11 reserved
12
reserved
13
reserved
14 reserved
15 reserved
Input.terminal function 0x01
0 DI1 input
0 invalid
1 valid
1 DI2 input
0 invalid
1 valid
2 DI3 input
0 invalid
1 valid
3 DI4 input
0 invalid
1 valid
4 DI5 input
0 invalid
1 valid
5 DI6 input
0 invalid
1 valid
6 DI7 input
0 invalid
1 valid
7 DI8 input
0 invalid
1 valid
8 AI1 input
0 invalid
1 valid
9 AI2 input
0 invalid
1 valid
10 AI3 input
0 invalid
1 valid
Output.terminal function 0x02
0 O1 output
0 invalid
1 valid
1 O2 output 0 invalid
164

A
p
p
e
n
d
i
x

I

1 valid
2 O3 output
0 invalid
1 valid
3 O4 output
0 invalid
1 valid
NOTE 1
Function 0x03 reading operation 0x06/0x10 writing operation
y00 reset the factory
setting
Return 0 Only can write into 5
y01 upload parameter
onto keyboard
Return 0 Invalid operation
y02 latest fault record Valid operation Invalid operation
y03y07
fault history record
Empty
record
00H
Invalid operation New record 01H
Confirmed
record
02H
y08reset fault record Return 0 Valid operation
y09 rated output current Valid operation Invalid operation
y10 rated output voltage Valid operation Invalid operation
y11 products series
80 0 3
Invalid operation
Family
serial
products
series
Input voltage
level
The number should be decimalization.
y12 soft ware version Valid operation Invalid operation
y13 product date year Valid operation Invalid operation
y14 product
monthdate
Valid operation Invalid operation
y15 user decode input Valid operation Invalid operation
y16 user input password Valid operation Valid operation
y17 parameter group
protection
Valid operation Valid operation
NOTE 2 running status byte
BIT 15 BIT 14 BIT 13 BIT 12 BIT
meaning
0No fault
1urgent stopping
fault
0No fault
1decelerating fault
0No fault
1alarming fault
0confirmed fault
1unconfirmed
fault
bit 11 BIT 10 BIT 9 BIT 8 BIT
meaning reserved reserved reserved
0No JOG.
1JOG running
meaning
0lower frequency
not arriving
1arrive lower
0upper frequency
not arriving
1arrive upper
00stopping 01accelerating
10decelerating
11running in a even speed
165

A
p
p
e
n
d
i
x

I

frequency frequency
meaning
0running reverse
1running forward
0: stopping
1: running
reserve
0: V/F control
1SV control
NOTE 3running command
meaning reserve reserve reserve reserve
Bit 11 BIT 10 BIT 9 BIT 8 BIT
meaning reserve reserve reserve reserve
meaning
0No free-stop
1:free-stop command
reserve
0JOG stopping
1JOG running
reserve
meaning reserve
0:reverse command
1:forward command
reserve
0:stop command
1:run command
NOTE 4fault style code
Serial.number LED display Fault message
0 E.OCP
System is disturbed or impacted by instant over current, over current signal
from current inspected circuit or drive circuit
1 reserve
2 E.OC3 Inverter output current exceeded 3 times of motor rated current
3 reserve
4 E.OU Over voltage
6 E.OL Over load
7 E.UL Under load warm
8 E.PHI Input phase loss
10 E.ntC Over heat
13 reserve
14 reserve
15 reserve
16 E.PId PID regulation fault
17 E.OHt Motor over heat fault
166

A
p
p
e
n
d
i
x

I

19 E.PG PG error
20 E.PHo Inverter output loss phase
21 E.COA Rs485 communication port A fault
22 E.COb Rs485 communication port B fault
23 E.CAL Parameter indentification fault
NOTE 5 fault funning status
LED first position LED second position LED third position LED fourth position
Bit15-Bit12 Bit11-Bit8 Bit7-Bit4 Bit3-Bit0
F 0 Forward
command
F 0 Forward status
- 0 Separative sign
A 1 Accelerating
running
R 1 Reverse
command
R 1 Reverse status D 2 Decelerating
running
S 2 Stop command S 2 Stop status
E 3 running in a even
speed
S 0 stop
E.g. keyboard display FF-Areturn data 0001said when fault occurs the inverter stateforward commandforward
stateaccelerating running
I-4-5CRC checkup sum
Data meaningdata frame CRC checkup sum, using 2 bytes.
Checkup sum address + function code + data

EncloseCRC computation program
unsigned int cal_crc16 (unsigned char *data, unsigned int length)
{
unsigned int i,crc_result=0xffff;
while(length--)
{
crc_result^=*data
++
;
for(i=0;i<8;i
++
)
{
if(crc_result&0x01)
crc_result=(crc_result>>1)^0xa001;
else
crc_result=crc_result>>1;
}
}
crc_result=((crc_result&0xff)<<8)|(crc_result>>8);
return(crc_result);
167

A
p
p
e
n
d
i
x

I

I-5 Example of communication protocol:
Valid setup and communications under normal circumstances, the host command and slave responses
are as follows:
0x03= read inverter multiple function code, at most can read 16 registers (register 2bytes)
Host command read inverterF01 keyboard set frequencyF02 frequency set up method
Slave address Function code Register address Register number CRC checksum
0x08 0x03 0x0001 0x0002 0x9552
Slave response inverter F01 keyboard set frequency to 50.00HzF02 frequency set up method to 0keyboard set frequency orRS485
Slave address Function code Read byte number Read content CRC checksum
0x08 0x03 0x04 0x1388,0x0000 0xE79D
Read byte number=2byte*register number
0x06write inverter single function code
Host command set up inverter F01 keyboard set frequency inverter to 50.00Hz
Slave address Function code Register address Register data CRC checksum
0x08 0x06 0x0001 0x1388 0xD5C5
Slave response inverter F01 keyboard set frequency to 50.00Hz
Slave address Function code Register address Register data CRC checksum
0x08 0x06 0x0001 0x1388 0xD5C5
0x10write inverter multiple function code, at most can write 16 registers(register 2bytes)
Host command inverter F01 keyboard set frequency to 50.00HzF02 frequency set up method to 0keyboard set
frequency or RS485
Slave
address
Function
code
Register address
Register
number
Register content byte
number
Register content
CRC
checksum
0x08 0x10 0x0001 0x0002 0x04 0x1388,0x0000 0x9851
Register content byte number=2 bytes * register number
Slave response
Slave
address
Function code
Register
address
Register
number
CRC
checksum
0x08 0x10 0x0001 0x0002 0x1091
0x01read multiple switch status
Host command read inverter whether arrive lower frequency, or arrive upper frequency
Slave address Function code
Starter to end
address
Switch number CRC checksum
0x08 0x01 0x0006 0x0002 0x5D53
Slave response inverter not arrive lower frequency nor upper frequency
Slave address Function code Read byte number Switch state CRC checksum
0x08 0x01 0x01 0x40 0x53E4
Host command read inverter fault
168

A
p
p
e
n
d
i
x

I

Slave address Function code
Starter to end
address
Switch number CRC checksum
0x08 0x01 0x0300 0x0020 0x3D0F
Salve response inverter low voltage (E.LU switch address 0x0305)
Slave address Function code Read byte number Switch state CRC checksum
0x08 0x01 0x04 0x20,0x00,0x00,0x00 0x6911
Note return byte 4 bytes
Return date in orderbit7-bit0, bit15-bit8, bit23-bit16, bit31-bit24
0x05write single switch status
Host command control inverter running
Slave address Function code Output address Output value CRC checksum
0x08 0x05 0x0000 0xFF00 0x8CA3
Slave response
0x08 0x05 0x0000 0xFF00 0x8CA3

Host command control inverter stop
0x08 0x05 0x0000 0x0000 0xCD53
Slave response
0x08 0x05 0x0000 0x0000 0xCD53
Note: set switch to 1,output value is 0xFF00;set switch to 0,output value is 0x0000.

169

A
p
p
e
n
d
i
x

I
I

Appendix II Instruction of the Proportional Linkage
Function
II-1. proportional linkage function:
The proportion interaction host computer:
Communication address = 128,
Communications port A is the communication port of host computer.
Communication port B can be used as the keyboard interface, or a PC host computer interface.
There is only one host inverter in one proportional linkage.
The host inverter control the running state, the slave inverter follow the hosts running state.
The proportion interaction slave computer:
Communication Address = 1 ~ 127,
Both communication port A and communication port B can be the communication port of slave
inverter.
In the slave inverter follow the host running and it can realize forced stopping by terminal or keyboard
if need.
For this function, the host computer should be set with the following parameters:
A28 Local communication address 128
For this function, the slave computer should be set with the following parameters:
F01 Keyboard set the frequency / Rs485 Command from proportion linkage Host
F02 Frequency main set mode
Keyboard setting frequency or RS485 0
Multi-segment digital voltage set 5
F03
Auxiliary setting mode of
frequency set
Keyboard setting frequency or RS485 0
Multi-segment digital voltage setting 5
Digital Pulse Set 6
F04
relationship between main and
auxiliary frequencies
The main setting individual control 0
The auxiliary setting individual control 1
main + auxiliary 2
main -auxiliary 3
Appendix II Instruction of the Proportional Linkage Function
170

A
p
p
e
n
d
i
x

I
I

(main *auxiliary)/maximum frequency 4
F05 Running control mode Proportional linkage control 4
Select this function, the slave inverter will follow the command of host inverter to run.
After select this function, it can also use keyboard, terminal and RS485 to control the
slave inverters running.
In the proportion of linkage during operation, if control by the keyboard, terminal,RS485
control, once the slave inverter stopped, the slave will N longer respond to the host command,
if need the slave once again to respond to host commands, it should control through the
keyboard, terminal and RS485, or after the host sends cease and desist commands then the
slave will respond the command again to run.
A28 communication address 1~127
A29 Baud rate Same as host
A30 Communication format Same as host
A55 Proportional linkage factor 0.10~10.00
During the proportional of linkage, the running state of slave inverter is controlled by the host
inverter.
Slave inverter F01 = proportional factor*the actual set frequency of host inverter of proportion
linkage.
Slaver S00 actual set frequency = slave F01 + frequency give and secondary amend +ascend/descend
adjusting.
II-2. Proportion linkage application Cases:
Features of proportional function:
1: the host inverter using the potentiometer to control the system speed and use the terminals to
control the forward/reverse running.
2: the slave follows the host running, the proportional linkage factor is 1.00
3: after get the running speed command from host inverter, the slave will store this command into to
F01.
4: the slave actual frequency is set through the keyboard or through terminal ascend/descend
adjusting.
5: the slave actual frequency is set through potentiometer adjusting.
6: the slave actual frequency = F01 + slave potentiometer adjusting + A40
The proportional linkage host settings:
F02 Frequency main set mode AI1 external analog setting
A28 Communication address
Host 128
11
A29 Baud rate 3: 9600bps
A30 Communication format 0
o36 DI1 input terminal function select
selectio

1:forward running
o37
DI2 input terminal function select

2:reverse running
The proportional linkage slave settings:
F02 Frequency main set keyboard set the frequency or Rs485 0
F03 Auxiliary setting mode of AI1 external analog setting 1
171

A
p
p
e
n
d
i
x

I
I

frequency set
F04
relationship between main and
auxiliary frequencies
main+Auxiliary 2
F05 Running control mode Proportional linkage control 4
A28 Communication address 1~127
A29 Baud rate Same as host inverter
A30 Communication format Same as host inverter
o36 DI1 input terminal function select 39:free stopping
o37 DI2 input terminal function select 40:Up command
o38 DI3 input terminal function select 41:Down command
A43 Multi-function key MF1 8:MF key is appointed to be Up command
A44 Multi-function key MF2 9:MFkey is appointed to be Down command
System wire connections:

172

A
p
p
e
n
d
i
x

I
I
I

Appendix III. RS485 PG Card Instruction
III-1. PI8000 PG can use arrange
type Encoder output method
1 +5V LINE DRIVER output
2 OPEN COLLECTOR output
3 Push-pull output type (complementary)
4 Voltage output type VOLTAGE
III-2. terminal function instruction
terminal Terminal function
A+ A- , B+ B-
PG signal input
Encoder output method:
1:+5V LINE DRIVER output
JP1/JP2 jump to LD
connect methodA+->A+ , B+->B+
A- ->A-, B- ->B-
R16/R17/R18/R19 disconnect.
2:OPEN COLLECTOR output
JP1/JP2 jump tp OC
Connect method: A ->A+ , B ->B+
R2/R4/R10/R11/R13/R15 disconect
3:Push-pull output type (complementary)
JP1/JP2 jump tp OC
R2/R4/R10/R11/R13/R15 disconnect
4:VOLTAGE output
JP1/JP2 jump to OC
R2/R4/R10/R11/R13/R15 disconnect

the adjustment of resistance associated with the output voltage
V+ =5V, R16/R17/R28/R29200
V+ =12VR16/R17/R28/R29=1K
V+ =24VR16/R17/R28/R292K
V+encoder powerthrough JP3 to select
Aout,Bout
PG signal output
Voltage output, voltage level determined by the encoder power supply
V+
Encoder power, through JP3 to select

173

A
p
p
e
n
d
i
x

I
I

PGND encoder
Encoder PG pulses range 300~9999
maximum pulses frequency receiver 1MHzwhen PG pulses=2500maximum speed=400Hz
III-3. terminal connection:
Earthing
Motor
Earthing
Power
DC- DC+1 DC+2
DC Reactor
Brake Unit
Optional
P18000
PG
V+
V-
A+
A-
B+
B-
PG
Earthing
Bout
Aout
B-
B+
A-
A+
PGND
V+
PI8000
Inverter
MCCB
Motor
3~
M
W(T3)
V(T2)
U(T1) R(L1)
S(L2)
T(L3) T
S
R
Bout
Aout

174

A
p
p
e
n
d
i

I
V

Appendix IV Converter Water Supply Controller Instruction
number E00 function Parameter setting definition Reference page
1
Special power
supply
8 Inverter power 174
13
Stable voltage
power
174
14
Constant
current power
-
2
Constant
pressure water
supply
9
Pump constant
pressure water
supply
175
3
Extruding
machine
15
Extruding
machine
-
IV-1. Extend functions supplement
IV-1-1. E00=8: variable frequency power
P03 PID given signal selection, you can set through the keyboard, analog AI1, pulse and other means
to set a given voltage.
Given voltage is calculated as follows:
Given voltage:220VAC
Given voltage setting =220*1.414/500*100%=62.2%
Frequency Power specific parameters:
No. name scope unit meanings
Factory
setting
E16 User parameter 1 0~9999 - Voltage increasing time 0
E17 User parameter 2 0~9999 - Voltage decreasing time 0
In regulated power supply mode, the output and input voltage are both adjustable.
The increasing time and decreasing time of output voltage is adjusted by F09 and F10.
E16 is the voltage increasing time, the definition of the output voltage increasing time is from9999
corresponds to 999.9 seconds.
E17 is the voltage decreasing time, the definition of the output voltage decreasing time is from9999
Voltage increasing/decreasing time just used to adjust the accelerate/decelerate time of output
frequency when the inverter running.
After the stopping command issued, the controller will stop the frequency output when the output
frequency decelerate to 0hz.
E18 User parameter 3 0~9999 - The max output voltage 0
For safety and reliability to ensure that the output voltage to bear the load within the system, we
need to define the maximum output voltage of the system.
If the system highest withstand voltage 250VACthen a maximum outout voltage= 250
E18=250
IV-1-2. E00=13: Voltage regulation power
In this mode,connect AI2,AI3 to Hall,then measure the output voltage and use2Halls to do redundant
work to ensure the output voltage will not exceed the Hall voltage limitation.
In this mode, the following parameters should be adjusted:
Appendix IX Converter Water Supply Controller Instruction
175

A
p
p
e
n
d
i
x

I
V

PID function group, P02 PID feedback signal selection.
AI2 is detected by analog and AI3 works as a redundant configuration to ensure the output voltage
safe and reliable.
When Feedback voltage is 100%, the corresponding Hall voltage is 500VAC, Hall output voltage is
5V.
Set o03=50%, o05=50%.
P03 PID given signal selection, you can set through the keyboard, analog AI1, pulse and other means
to set a given voltage.
Given voltage is calculates as follows:
When the given voltage =220VAC, given voltage setting =220*1.414/500*100%=62.2%
Other PID parameters are adjusted according to the site.
Under PID regulated power supply mode, the voltage acceleration and deceleration time is
controlled by PID parameters, it wont affect by voltage acceleration and deceleration time.
Voltage regulation power specific parameters:
No. name Range unit Description
Factory
setting
E16 User parameter 1 0~9999 - Voltage increasing time 0
E17 User parameter 2 0~9999 - Voltage decreasing time 0
In Voltage regulation power mode, the output and input voltage are both adjustable.
The increasing time and decreasing time of output voltage is adjusted by F09 and F10.
E16 is the voltage increasing time, the definition of the output voltage increasing time is from 9999
E17 is the voltage decreasing time, the definition of the output voltage decreasing time is from
9999 corresponds to 999.9 seconds.
Voltage increasing/decreasing time just used to adjust the accelerate/decelerate time of output
frequency when the inverter running.
After the stopping command sent, the controller will stop the frequency output when the output
frequency decelerate to 0 hz.
E18 User parameter 3 0~9999 - Max output voltage 0
For safety and reliability to ensure that the output voltage to bear the load within system,we need to
define the maximum output voltage of the system.
If the System highest withstand voltage 250VAC
Then E18=250VAC.
IV-1-3. Converter water supply controller instruction
IV-2-1. Constant water supply system parameters:
(1) loading types with constant water supply function:
Parameter Keyboard display setting Meaning
E00 Load type 9
E12 set to be single pumpno need the constant
pressure water supply interface board
E12 set to multi-pumpneed constant pressure
water supply interface board,while realize
4-pumps constant pressure water supply function.
(2) PID adjusting in constant water supply system
Parameter Keyboard Display Setting Meanings
F01 Keyboard set frequency 0 Keyboard set the frequency 0hz
176

A
p
p
e
n
d
i
x

I
V

F02 Frequency main set mode 0 Keyboard set frequency or RS485 set frequency.
F03 Frequency auxiliary set mode 7 PID adjusting mode
F04
main and auxiliary frequencies
set
2 main+ auxiliary set mode
P00 PID configure 0000
single-way,the negative regulator, failure is not
action
P02 Feedback signal select 1~3
External analog feedback signal given by the AI1
/ AI2 / AI3
P03 Given signal select 0~6
Given signal can select the
keyboard/Rs485,potentiometers, digital voltage,
digital pulse, etc.
P05 PID integration time Setting according the site.
P06 PID differential time Setting according the site.
P07 PID proportional gain Setting according the site.
P09 Deviation Limit Setting according the site.
P12 PID Display Range Setting according the site.
(3) Constant pressure water supply special parameters
E01 Starting pressure deviation 10% Starting pressure deviation is 10%
E02 Starting time delay 2.0 Starting delay time is second.
E03 Stop frequency 15.00 stop at frequency 15HZ.
E04 stop time delay 2.0 Stop time is 2 second.
E05 High pressure arrival value 80%
feedback pressure reach and exceed the value of
this parameter, the I / O output terminal select
25, then it will output arrival signal.
E06 Low pressure arrival 60%
when feedback pressure less than the low
pressure reached value of this parameter, the I /
O output terminal select 26, then it will output
arrival signal.
E07 Timing to water supply 0000 Timing to water supply function invalid
(4) Multi-function constant pressure water supply pump specific parameters
Parameter Keyboard Display Setting Meaning
E08 Timing shift alternation time 0.25
According to first start first stop principles to con -
- trol pump rotation,rotation time of 0.25 hours
E09
electromagnetic switching
action delay
0.500
When set up a station pump (drive motor) to
switch from variable frequency industry frequ -
ency, or from industry frequency to variable
frequency, and set its electromagnetic switching
action delay time is 0.5 seconds.
E10 Pumps shift judging time 100
To set the determine time 100 seconds from inv
- erter output frequency reaches the upper limit
frequencies until increase pump (drive mo -
tor); or from inverter output frequency reaches
the lower limit frequencies until decrease pump
(drive motor).
177

A
p
p
e
n
d
i
x

I
V

E11
Constant Pressure Water
Supply Configuration
0000
Decelerating stop: When the inverter failure, the
rotation switching way is from variable freque -
ncy pump to industry frequency and the pump
maintain the status.
E12 Multi-pump configuration 1111 N. 1 ~ 4 pumps are frequency controlled pump
E13 Multi-pumps status
Multi-pump control mode, displays the status of
each pump
E14 Soft-start Pump Control 0000
Multi-pump control mode, set the control mode
of each pump, currently set to Full Stop
(5) constant pressure water supply IO parameter:
o21~o24 Output signal select 25 High pressure arrival
o21~o24 Output signal select 26 Low pressure arrival
o36~o46 Input terminal function select 51 Pump 1 soft start
o36~o46 Input terminal function select 52 Pump 1 stop
o36~o46 Input terminal function select 53 Pump 2 soft starter
o36~o46 Input terminal function select 55 Pump 3 soft starter
o36~o46 Input terminal function select 57 Pump 4 soft state
o36~o46 Input terminal function select 59 Manual shift command
o36~o46 Input terminal function select 60 Timing of water supply time-zero
IV-2-2. Application
It is special appendix for multiple pumps, which run with PI7000 family inverter to control the
multiple pumps water supply system effectively.
IV-2-3. Operation and connection notice:
If it is power frequency motor, probable thermal relay must be used to protect motor.
AC contactor with machinery chain equipment should be used between the power frequency
bypass and inverter output of aside the motor, lock logically on the electri control circuit to avoid
the short circuit of the power frequency and inverter output which damage the inverter and
equipments.
The phase order of the power frequency to the motor should be the same with the phase order of
the inverter output to avoid the motor reverse. Please confirm the phase order and operate.
When wiring the control signal of the inverter, please leave it away with the driving line, and do
not make them in the same wire, otherwise it will lead wrong action.
Screen cable is used for Pressure set signal and pressure feedback signal.
IV-2-4. Dimension
(1) Dimension of water supply control card
178

A
p
p
e
n
d
i
x

I
V

(2) Dimension of water supply controller
fixed plate fixed plate
fixed plate
the size of fixed plate

Note: The fixed plate can be fixed by any mounting hole in the figure.

179

A
p
p
e
n
d
i
x

I
V

IV-2-5. IV-2-5. Frequency of water supply connection to the drive controller
Connection of water supply controller with inverter, the communniction cable and power
cable are connected as below

180

A
p
p
e
n
d
i
x

I
V

IV-2-6. System diagram

Remarks: ZK air switch KM contactor
JR thermo-relay M motor
IV-2-7. Water supply control mode
When several pumps supply water meanwhile, because of the different time(daytime and night),
different season(winter and summer), the variation of the water flow is great. To save energy and protect
the equipment, please run pumps as many as you need and stop pumps as many as you do not need.
Inverter will confirm the number of the running pumps according to the requirement of the pressure
close loop control. In the set range, only one pump is controlled by the inverter at the same time.
If the timing shift interval time is set 0.05~100.00, when the related running time is stable, inverter
inverter will shift up the pumps according to stop first or open first to ensure each pump has the chance to
run and avoid the pump rusted because of long time N use.
After the pumps run to the upper and lower, arrive the adding pumps or reducing pumps time,
inverter will add or redcue the pumps according to stop first or open first to ensure each pump can run
and avoid the pump rusted because of long time N use.
IV-2-8. Soft-start pump control mode
Set the soft start pump by E12 and through the input terminals o36 ~ o46, respectively controlled
soft-start pump start and stop.
Soft-start pump terminal control, stop first.
Soft-start pump is not controlled by constant pressure water supply system.Soft-start pump can be
used as sewage pumps and fire pumps.
IV-2-9. Application Guide
3 Pumps constant pressure water supply + sewage pump
181

A
p
p
e
n
d
i
x

I
V

(1) pump configurations: variable frequency pump 3 units, 15kW,1 unit sewage pump,15kW.
(2) The set pressure 0.8Mpa.
(3) pressure gauge options: pressure transmitter, DC 4 ~ 20mA output, 1.6Mpa.
(4) Inverter choice: PI8000 015F3 and WSC_RS485 water supply board.
(5) Hardware Connection.
(6) Parameter setting

182

A
p
p
e
n
d
i
x

I
V

loading types with a constant pressure water supply function:
E00 Loading type 9
Multi-pump constant pressure water supply, need constant
pressure water supply interface board, while realize4pump
constant pressure water supply pump function.
PID adjust in constant pressure water supply
F01 Keyboard set frequency 0 Keyboard set the frequency 0hz
F02
Frequency main set
mode
0 Keyboard set frequency or RS485 set frequency.
F03
Frequency secondary
set mode
7 PID adjusting mode
F04
elationship between
main and auxiliary
frequencies given
2 main+ auxiliary set mode
F05 Running control mode 3 Terminal control
A29 baud rate 3 baud rate 9600
P00 PID configure 0000 single-way, the negative regulator, failure is not action
P02
Feedback signal
select
3 External analog feedback signal given by the AI3
P03 Give signal select 2 External analog given by AI2
P05 PID integration time 0.250 Setting according the site.
P06 PID differential time 0 Setting according the site.
P07 PID proportional gain 100.0 Setting according the site.
P09 Deviation Limit 5.0 Setting according the site.
P12 PID Display Range 1.6
adjust according actual requirement,display the actual pres
- sure value is160.0, it means1.6Mpa.
Constant pressure water supply specific parameters
E01
Starting pressure
deviation
10% Starting pressure deviation is 10%
E02 Starting time delay 2.0 Starting delay time is second.
E03 shutdown frequency 15.00 shutdown at frequency 15HZ.
E04 Shutdown time delay 2.0 shutdown time is 2 second.
E05 High pressure arrival 80%
hen feedback pressure reach and exceed the high pressure
reached value of this parameter, the I / O output terminal
select 25, then it will output arrival signal.
E06 Low pressure arrival 60%
when feedback pressure less than the low pressure
reached value of this parameter, the I / O output terminal
select 26, then it will output arrival signal.
183

A
p
p
e
n
d
i
x

I
V

E07
Regular time water
supply
0000 Regular time water supply function invaid
Multi-function constant pressure water supply pump specific parameters
Parameter Keyboard Display Setting Meaning
E08
E08 regular rotation
interval
0.25
According first start first stop principles to control pump
rotation, rotation time of 0.25 hours
E09
Electromagnetic
switching action delay
0.500
When set up a station pump (drive motor) to switch from
variable frequency industry frequency, or from industry
frequency to variable frequency, and set its electromagn -
etic switching action delay time is 0.5 seconds.
E10
Pump switch to judge
the time
100
To set the determine time 100 seconds from inverter out -
put frequency reaches the upper limit frequencies until
increase pump (drive motor); or from inverter output
frequency reaches the lower limit frequencies until
decrease pump (drive motor).
E11
Constant Pressure
Water Supply
Configuration
0
Shutdown: When the inverter failure,the rotation switch -
ing way is from variable frequency pump to industry fre -
quency and the pump maintain the status.
E12
Multi-pump
configuration
2111
N. 1 ~ 3 pumps are frequency controlled pump, pump 4
is soft-starter controlled pump.
E13 Multi-pump status 1112
Multi-pump control mode, displays the status of each
pump
E14
Soft-start Pump
Control

Multi-pump control mode, set the control mode of each
pump, i currently set to Full Stop
constant pressure water supply IO parameters:
Parameter
Value read On
Keyboard Display
Setting
Value
Meanings
o21
o1 input signal select 1
25 High pressure arrival
o22
26 Low pressure arrival
o23
1 Fault input alarm
o36
(DI1) input terminal
function selection
1 FWD
o37
(DI2)input terminal
function selection
39 Free parking
o38
function selection
59 Manual rotation command
o39
function selection
60 Timing of water supply time-zero
o40
function selection
55 Pump 3 soft starting
o41
function selection
56 Pump 3 stopping

Product Feedback
Dear users:
Thank you for your interest and purchase powtran products! In order to provide better service for
you, we hope to be able to timely access to your personal information and your purchased powtran products
information .we hope to learn about your present and future demand for powtran products and also your
valuable feedback on our products. In order to help you get our service faster and more convenient, please
visit our company web site http://www.powtran.com and refer to column "technologies and services" and
"Download" for feedback. 1) download the updated manual for your products.
2) read and download various of product technical information, such as operation instruction, product
specification and features, FAQ, etc.
3) application case sharing.
4) technical consult, on-line feedback
5) feedback product information and customer requirement information through e-mail.
6) inquiry for the latest products, obtain various types of additional services such as warranty and
extended.

PI8000 Manual MV110716E

Uploaded by

Copyright:

Available Formats

PI8000 Manual MV110716E

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PI8000 Manual MV110716E

Uploaded by

Copyright:

Available Formats

Foreword

the size of fixed plate

You might also like