AgRemote RevA Guide ENG

AgRemote Software
Guide for AgGPS Receivers
F
Revision A
February 2004
Corporate Office
Trimble Navigation Limited
Agriculture Business Area
9290 Bond Street, Suite 102
Overland Park, KS 66214
USA
+1-913-495-2700 Phone
trimble_support@trimble.com
www.trimble.com
Copyright and Trademarks
© 2004, Trimble Navigation Limited. All rights
reserved.
Trimble, the Globe & Triangle logo, and AgGPS are
trademarks of Trimble Navigation Limited, registered in
the United States Patent and Trademark Office and other
countries.
Microsoft and Windows are either registered trademarks
or trademarks of Microsoft Corporation in the United
States and/or other countries.
All other trademarks are the property of their respective
owners.
Release Notice
This is the February 2004 release (Revision A) of the
AgRemote Software Guide for AgGPS Receivers.
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Downloading and Installing AgRemote . . . . . . . . . . . . . . . . . . 5
Downloading the install software from the Web . . . . . . .. . .. . .. 5
Installing the software in your computer . . . . . . . . . . .. . .. . .. 7
Starting AgRemote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AgRemote Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Navigating Menus and Screens . . . . . . . . . . . . . . . . . . . . . . . 10
Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Positioning Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General GPS position information . . . . . . . . . . . . . . . . . . . . . . 16
Configuring the Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Configuring the Communication Ports. . . . . . . . . . . . . . . . . . . . 24
Configuring input / output communication . . . . . . . . . . . . . . . . . 27
Configuring Differential GPS. . . . . . . . . . . . . . . . . . . . . . . . . 31
OmniSTAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
WAAS/EGNOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Configuring the Receiver to Operate in RTK Mode . . . . . . . . . . . . 35
Configuring Beacon DGPS . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing Passcodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Navigation Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
AgRemote Software 3
Introduction
2.1 Introduction
This document describes how to set up and begin using the AgRemote
software. It includes an overview of the AgGPS® menu system.
The AgRemote software provides an interface that you can use to
access the internal AgGPS menu system. Use the AgRemote menus
and screens to configure the receiver settings and review the receiver
status. To view the entire AgGPS menu system, see the AgRemote
navigation maps document for your receiver firmware, on the Trimble
website: www.trimble.com.
4 AgRemote Software
Downloading and Installing AgRemote
2.2 Downloading and Installing AgRemote

AgRemote requires Microsoft® Windows® 95, 98, Me,
Windows 2000, or XP.
Note – Later versions of the AgRemote software may not install
correctly under Windows 95.
22.1 Downloading the install software from the Web

Note – Some buttons and dialogs described in this procedure appear
differently in different versions of Windows. Their functions and the
steps to follow remain the same.
1. Go to www.trimble.com/agremote.html.
Click Download it now.
You are prompted to run the install program over the Web or
download the install software to your computer.
2. Select Save this program to disk.
3. Click OK.
AgRemote Software 5
Downloading and Installing AgRemote
4. Choose a folder on the hard drive of your computer.
5. Click Save.
The AgRemote install software is downloaded from the website
to your computer.
20.1 Installing the software in your computer

1. In Windows Explorer, double-click the AgRemote install
software file you downloaded earlier.
The InstallShield message appears:
2. Click Yes.
3. The InstallShield Setup window appears. Follow the prompts to
install the AgRemote software.
6 AgRemote Software
Starting AgRemote
2.1 Starting AgRemote

1. Using the correct receiver cable, connect the receiver to the
serial port on the computer.
2. Connect a power supply to the receiver.
3. Turn on the receiver.
4. Select / Programs / AgRemote / AgRemote.
The AgRemote window appears.
5. Select File / Connect.
The Port Settings dialog appears.
6. Make sure that the Comm Port field is set to the port to which
you have connected the receiver.
7. Click OK.
AgRemote establishes communication with the receiver and
displays the Home screen of the AgGPS menu system.
AgRemote Software 7
Starting AgRemote
Figure 1 shows the AgRemote window, the Home screen, and

the navigation keys.
Home screen
S
D 3D V08 DOP02
S
S 1554.4970 /N 10
Esc Enter Up Down Right Left
Keys
Figure 1 AgRemote window, Home screen, and navigation keys
8 AgRemote Software
AgRemote Keys
Figure 2 shows a typical AgRemote Home screen. The information

that appears on the Home screen depends on the type of receiver and
how the receiver is configured.
Number of GPS satellites being tracked
Position type Current PDOP value
GPS indicators
D/3D í07 DOP03
WAAS 122 ÷ø04 Correction
indicators
Correction type Signal-to-Noise ratio

of DGPS satellite
DGPS satellite name or ID
Figure 2 Home screen
You can leave the Home screen running while you work. It enables
you to monitor the receiver status. To return to the Home screen after
viewing other receiver menus and screens, press 5 one or more times.
2.1 AgRemote Keys

Press AgRemote keys to access menus and screens where you can:
• view the receiver status
• change the receiver configuration (for more information, see
page 21)
• control the receiver utility/guidance functions
• enter data
• select options
AgRemote Software 9
Navigating Menus and Screens
The action associated with each of the AgRemote keys depends on

whether a menu or a screen is displayed. See Table 1.
Table 1 AgRemote key actions
Key Action when a menu is displayed Action when a screen is displayed
4 Return to the top of the menu when an From the Home screen: change Satellite
Exit screen appears after the last DGPS source mode.
screen in a menu. From the Lock Display Cfg screen: display
the Enter Password screen.
From other screens: perform an action
associated with that screen.
2 Move down a menu level. Move down through the screens in a menu.
Display the first screen from a lower Move down through the list of options in
level menu. multiple-choice fields.
1 Move up a menu level. Move up through the screens in a menu.

Move up through the list of options in
multiple-choice fields.
3 Move horizontally through the upper- Select the next alphanumeric or

and lower-level menus. multiple-choice field on a screen. When
Move from the last upper-level menu to alphanumeric or multiple-choice fields are
the Home screen. available, the symbol appears in the
corner of the screen.
Move to the next letter or digit of a field.
5 Move up one menu level. Move from a screen to the menu screen for
Ultimately, return to the Home screen. that screen.
If pressed again: return to the previous level.
If pressed again: return to the Home screen.
2.2 Navigating Menus and Screens

AgRemote uses menus and sub-menus to organize configuration and
status screens.
AgRemote displays menus such as Field Operations, Status, and
Configuration. These are accessed from the Home screen. Use a menu
to navigate to another menu or a sub-menu.
10 AgRemote Software
Each menu has one or more lower level menus (sub-menus) which are
used to access status and configuration screens. Use screens to view
the receiver status or to change a configuration setting.
Not all menus, sub-menus, and screens are available for all receivers.
For a diagram showing the full menu system, see the navigation map
for your receiver and associated firmware. See also Navigation Maps,
page 40.
When you are using the receiver front panel keypad to navigate the
menu system, press 2+1 simultaneously to move to the previous
menu. Press and hold (or press repeatedly) 2+1 simultaneously to
return to the Home screen.
AgRemote Software 11
Figure 3 shows the structure of a typical sub-menu (accessed from the

Home screen).
Home screen
Home
1 2
Display Options
sub-menu Display
Options
1 2
Contrast Units
Screens 1 2
1 2
Lock Clear
Display Memory
1 2 1 2
Update
Language Receiver
1 2 1 2
Exit
Exit screen indicates
end of the menu
Figure 3 Typical sub-menu structure (Display Options)
To move between screens, press 2 or 1. When Ð appears in a

screen, press 4 to perform the action specified on that screen.
22.1 Fields
A field in a screen can display status information or a configuration
setting. A field can be:
• display-only
• multiple-choice
• alpha, numeric, or alphanumeric
Display-only fields
You cannot edit a display-only field. A display-only field shows status
information and other data that is automatically generated by the
receiver or acquired from satellite signals. Examples include DGPS
data on the Home screen, or details of the current receiver options. See
Figure 4.
Receiver Option Details field
Figure 4 Example of a display-only field
Multiple-choice fields
In a multiple-choice field, you select one option from a list.
To select a multiple-choice field, press 3. Then press 2 or 1 to
move through the list. When the required option appears, press 4 to
select it and save the changes.
For example, multiple-choice fields appear in the EZ Sat DGPS

Configuration screen for some receivers. Figure 5 shows a
multiple-choice field that lists available satellite providers and another
that lists satellite coverage beams.
Satellite Provider field
Satellite Coverage Beam field
Figure 5 Examples of multiple-choice fields
Alpha, numeric, and alphanumeric fields

You can enter only letters in an alpha field, only numbers in a numeric
field, or a combination of letters and numbers in an alphanumeric
field.
To enter a value in a field:
1. Press 3 to select the field and activate the cursor on the first
letter or number.
2. Press 2 or 1 to move through the list of letters or numbers
until the required letter or number appears.
3. Press 3 to move to the next place in the field.
4. Repeat Steps 2 and 3 to enter all required characters.
5. Press 4 to save the changes.
Positioning Mode
An example of a numeric field appears in the Satellite Freq screen. See

Figure 6. You can manually enter the broadcast frequency of a satellite
service provider in this field.
Satellite Frequency field
Figure 6 Example of a numeric field
2.1 Positioning Mode

Trimble AgGPS receivers can operate in the following positioning
modes:
• Real-Time Kinematic (RTK) GPS positioning
• Satellite Differential GPS (DGPS) positioning, which includes
OmniSTAR VBS, OmniSTAR HP, WAAS, and EGNOS
• Beacon Differential GPS (DGPS) positioning
• Autonomous GPS positioning
The type of positioning mode used depends on the type of receiver,
how the receiver is configured, and what correction type is being used.
Positioning Mode
21.1 General GPS position information

The first line of the Home screen displays general GPS positioning
information for the type of signal that is being used.
Figure 7 shows the GPS status indicators that can appear on the first
line of the Home screen display.
D/3D í07 DOP03

Current Position Dilution of
Precision (PDOP) value
Number of GPS satellites (SVs) being tracked
Position type
Figure 7 GPS status
Table 2 explains the indicators that can appear in the Position Type
field.
Table 2 Position types
Display Description
SRCH Searching for satellites
TRCK Tracking satellites
G/2D Outputting 2-dimensional autonomous positions
G/3D Outputting 3-dimensional autonomous positions
h/3D Outputting 3-dimensional unconverged OmniSTAR HP
positions
H/3D Outputting 3-dimensional converged OmniSTAR HP
positions
D/2D Outputting 2-dimensional differential positions
Positioning Mode
Table 2 Position types (continued)
Display Description
D/3D Outputting 3-dimensional differential positions
r/3D Outputting 3-dimensional float (uninitialized) RTK positions
R/3D Outputting 3-dimensional fixed (initialized) RTK positions
Note – RTK and HP modes are not supported by all receivers. If you
are unsure, refer to your receiver documentation.
The “/” symbol in the position type spins when the receiver is
operating correctly.
RTK mode status indicators

When the receiver is in RTK mode, the second line of the Home screen
displays the status indicators shown in Figure 8.
CMR Q:%86 A:2.0

Age of RTK signal, in seconds,
since last RTK correction
received.
Quality indicator: percentage of good RTK

correction received.
Receiver is using CMR RTK corrections.
Figure 8 RTK mode status indicators
Positioning Mode
Satellite DGPS mode status indicators

When the receiver is in Satellite DGPS mode, the second line of the
Home screen displays the status indicators shown in Figure 9.
S 1556.2550 ÷ø10
Signal-to-noise ratio of DGPS
signal, see Table 4.
Frequency for tracked DGPS satellite. Available

frequencies vary according to your location and
DGPS service provider.
Receiver is using Satellite DGPS corrections.
Figure 9 Satellite DGPS mode status indicators
Table 3 shows the possible satellite differential mode indicators.

Table 3 Satellite differential mode status indicators
Indicator Description
S ####.### S/N ## Operating in Satellite Differential mode
S SRCH ###.## Searching for Satellite Differential signal
S TRCK ####.## Tracking satellite without acquiring signal lock
Table 4 explains the signal-to-noise ratio values for both Satellite and
WAAS/EGNOS DGPS modes.
Table 4 Signal-to-noise values
Value Description
Below 4 Unusable
4–8 Fair
>8 Excellent
Positioning Mode
WAAS/EGNOS DGPS mode status indicators

When the receiver is in WAAS/EGNOS DGPS mode, the second line
of the Home screen displays the status indicators shown in Figure 10.
WAAS 122 ÷ø07

Signal-to-noise ratio of DGPS signal,
see Table 4.
WAAS satellite ID
Receiver is using WAAS/EGNOS corrections.
Figure 10 WAAS DGPS mode status indicators
Positioning Mode
Beacon DGPS mode

When the receiver is in Beacon DGPS mode, the Home screen
displays “B” (Beacon DGPS) in the lower left corner. The second line
of the Home screen displays the status indicators shown in Figure 11.
B
B A-R
A-R 310.0
310.0 ÷ø15
÷ø15
The beacon signal-to-noise
ratio. S/N values range from 0
to 30. High numbers are best.
Above 6 is acceptable.
The beacon frequency. Frequency varies

depending upon the beacon used.
The beacon operating mode.
Indicates the receiver is using beacon DGPS.
Figure 11 Beacon DGPS status
Note – Beacon DGPS mode is not supported by all receivers. If you

are unsure, refer to your receiver documentation.
Configuring the Receiver
Table 5 describes messages that can appear when the receiver is in

Beacon DGPS mode.
Table 5 Beacon DGPS operating mode messages
Message Description
B The receiver is operating in Beacon mode.
Beacon Searching The receiver is searching for beacon signals.
Beacon Tracking The receiver is tracking beacon signals and is
attempting to gain lock.
Beacon Idle Beacon DGPS is not active.
Beacon FFT The receiver is looking for a beacon across the
signal spectrum.
Beacon Disabled Beacon DGPS is disabled in the receiver. You need
to change configuration settings to enable Beacon
DGPS.
External RTCM Differential corrections are being provided by an
external source, through port A or port B.
2.2 Configuring the Receiver

This section describes how to configure the receiver using the menu
system.
Note – Not all screens are displayed by AgRemote. The screens that
are displayed depend on the type of receiver you are using and what
options are enabled for your receiver.
22.1 Display Options

Use the Display Options sub-menu to control how information is
displayed in the screens that you can access from the AgRemote
menus.
To view the Display Options sub-menu:

• From the Home screen, press 2.
Setting the language

To change the language displayed:
1. Navigate to the Language screen:
2. Press 3 to select the Language field.

3. Press 2 or 1 until the required language is displayed.
4. Press 4 to select the language and save the changes.
5. Press 5 to return to the Display Options menu.
The screen automatically displays the selected language.
Setting the units

What you select in the Units screen determines whether US, Metric, or
Nautical units are displayed in the screens that you access from the
AgRemote menus.
Note – This setting does not affect GPS position data output.
1. Navigate to the Units screen:
2. Press 3 to select the Units field.
3. Press 2 or 1 until the required unit is displayed.

4. Press 4 to select it and save the changes.
5. Press 5 to return to the Display Options sub-menu.
6. Press 5 again to return to the Home screen.
Locking the Configuration menus

To prevent unauthorized changes to the configuration, you can lock
the Configuration menus:
1. Navigate to the Lock Display Cfg screen.
2. Press 4 to display the Enter Password screen. The cursor is
active on the first digit:
3. Use the last five numbers of the receiver serial number as the
password (or “passcode”).
Press 2 or 1 until the first digit of the serial number appears.
4. Press 3 to select the next digit.
5. Repeat Step 3 and Step 4 until all five digits are entered.
The Valid Password message appears, and the Configuration
menus are no longer displayed when you navigate the menus.
If the message Invalid Password appears, enter the password again.
B Tip – When the Configuration menus are locked, you can view most
Configuration menu settings from the Status menus.
To unlock the Configuration menus, repeat the above procedure.
Clearing battery-backed RAM
C Warning – When you select the Clear BB Ram option, any changes that
you have made in the Configuration menus are deleted and cannot be
restored.
Use the Clear BB RAM screen to remove all configuration settings in

the receiver memory (RAM) and return the receiver to its factory
default configuration settings.
To delete battery-backed memory:
1. Navigate to the Clear BB RAM screen.
2. Press 3. This activates the cursor.
3. To select Yes, press 2 or 1.
4. Press 4. This clears the configuration settings.
20.1 Configuring the Communication Ports

Some AgGPS receivers have two serial ports. Through these ports
(RS-232 and CANBUS), the receiver can communicate with two
devices simultaneously. To do this, it uses the standard power/data
cable provided with the receiver.
Configure the communication ports to ensure that the receiver outputs
the correct GPS position data type for the hardware device or software
program that is connected to the receiver.
Note – As both ports are configured in the same way, this section
describes only Port A.
To access the configuration sub-menu for Port A:

1. From the Home screen, press 3 until the Configuration menu
screen appears.
2. Press 2. The first Config sub-menu appears.
3. Press 3 until the Port A Config sub-menu appears:
Port A Config
Press v to Enter
4. Press 2 to move through the screens.
The following section describes how to configure the appropriate Port
A Config screens. The menu for Port B is identical.
Note – Not all configuration sub-menus appear in all cases. The
configuration sub-menus that appear depend on the receiver and the
firmware that you are using.
Figure 12 shows the menus that you use to access the configuration
screens.
Configuration
2
(Guidance Config 3 Lightbar Config 3 ) Func Key Config 3
Log Config (RDL) 3 GPS Config 3 DGPS Config 3 RTK Config 3
Port A
Config
1 2
Port A NMEA 3
In/Out Messages
1 2 1 2
Port A Out NMEA/TSIP

RTS/CTS Output Rate
1 2 1 2
NMEA 1
1 Hz NMEA
Messages
1 2 1 2
NMEA 2
Exit
Messages
1 2
Figure 12 Port A Config sub-menu
20.1 Configuring input / output communication

Configure the Port Input/Output communication settings for
communicating with the AgGPS Lightbar, other external hardware
devices, and software programs. Table 6 describes the input settings.
Table 6 Port input settings
Setting Description
None Inputs nothing to the receiver.
TEXTB The receiver can accept ASCII data from an external device,
such as a chlorophyll meter, on Port A, merge it with NMEA GPS
data, and output the combined data on Port B. The incoming data
must be limited to 66 ASCII characters and must be terminated
by a carriage return and line feed (hex characters 0x0D 0x0A).
The NMEA string outputs as $PTNLAG001,<up to 66 ASCII
characters>*<2 digit checksum><CR><LF>. For the receiver to
output the combined NMEA string, NMEA must be selected as
the output protocol on Port B.
TEXTA See the description for the TEXTB setting. TEXTA outputs on
Port A, not Port B.
RTCM The receiver can accept RTCM data from an external DGPS
device, such as an FM pager.
TSIP The receiver can accept or output TSIP data packets from the
port when using the AgRemote program.
LBAR The receiver can accept or output data from the AgGPS Lightbar.
You must select this setting when you use the AgGPS Parallel
Swathing Option.
Note – The AgGPS Lightbar is not supported by all

receivers.
CMR The receiver can accept real-time corrections (CMR data) from
an external source, such as a Trimble radio.
RTKLNK The receiver can accept real-time corrections (CMR data) from
an external source, such as a Trimble radio.
When setting the baud rate, note the following:

• If you are using 19200 or 38400, the input rate must match the
output rate.
• If Port A is operating at 19200, Port B can operate at 1200,
2400, 9600, or 19200 (not 38400).
• If Port B is operating at 38400, Port A can operate at 1200,
2400, 9600 and 38400 (not 19200).
Note – These limits do not apply to the AgGPS 252 receiver.
To change the input or output settings:
1. From the Port A Config sub-menu, press 2 until the Port-A
Input/Output screen appears:
åæ I RTCM 9600
8N1 0 NMEA 4800

3. Press 2 or 1 to change the value.
4. Press 3.
Note – If the baud rate and input/output protocol settings are
changed, AgRemote loses connection with the receiver.
5. Repeat Steps 3 and 4 until you have set all the required values.
6. Press 4 to save all the changes.
7. Press 2 to move to the next screen.
Selecting NMEA messages for output

When the port output setting has been changed to NMEA, use this
screen to select the National Marine Electronics Association (NMEA)
messages output from the current port. Only upper-case NMEA
message types are output. The default messages are GGA, GSA, VTG,
and RMC.
To select the NMEA messages for output:
1. From the Port A Config sub-menu screen, press 2 until the
NMEA1 screen appears:
åæ NMEA1 GGA gll

grs GSA gst gsv
2. Press 3 to activate the cursor on the first NMEA message

type.
3. Press 2 or 1 until the NMEA message type appears in
uppercase.
4. Press 3 to select the next message type.
5. Repeat Steps 4 and 5 until all the message types that you want
to output appear in uppercase.
7. Repeat this procedure in the other NMEA screens, as required.
For detailed information about the content and structure of NMEA
messages, see the NMEA-0183 Messages guide on the Trimble
website at www.trimble.com.
Port output rate

Use the Message Rate screen to vary the NMEA and TSIP output rate.
For example, if the AgGPS Parallel Swathing Option is connected,
AgGPS Lightbar data is output 5 times per second (5 Hz). At the same
time, on the other port, NMEA or Trimble Standard Interface Protocol
(TSIP) data can be output to a computer software package, yield

monitor, variable rate controller, or other equipment. That data can be
output at the same rate, or at a slower rate than the lightbar data.
If you require an output rate of 2, 5, or 10 positions per second, you
must have the Fast Rate Option installed in the receiver or a receiver
that outputs at these rates as standard. All new AgGPS receivers come
with the Fast Rate Option as standard.
Note – Select ASAP if you want the output rate to be the same as the
output rate selected on the Position Rate screen under the GPS Config
sub-menu.
To set the NMEA / TSIP message output rate:
1. From the Port A Config sub-menu screen, press 2 until the
Message Rate screen appears:
åæNMEA out 01 s
TSIP out 01 s
2. Press 3 twice to set the NMEA output rate. This places the
active cursor on the second digit of the NMEA line.
3. Press:
– 2 to set the output rate to ASAP
– 1 to increase the output rate by one second. Press this key
as often as necessary, to a maximum of 99 seconds.
4. Press 3 twice to set the TSIP output rate. This moves the
cursor to the second digit of the TSIP line. Repeat Step 3.
20.1 Configuring Differential GPS

For the receiver to output GPS position coordinates of submeter
accuracy, select a differential signal from one of the following sources:
• WAAS/EGNOS – free service, limited availability
The Wide Area Augmentation System (WAAS) augments GPS
with additional signals for increasing the reliability, integrity,
accuracy, and availability of GPS in the United States. EGNOS
(European Geostationary Navigation Overlay System) is the
European equivalent of WAAS.
• OmniSTAR – paid subscription, available worldwide
You can use the OmniSTAR paid service as an alternative to
WAAS/EGNOS. OmniSTAR provides over-the-air DGPS
activation.
To use the differential signal from the selected provider:
1. Configure the receiver.
2. Activate the receiver.
3. Enable the receiver.
For details, see the following sections.
To configure the receiver to receive signals from any provider:
1. Navigate to the DGPS Config sub-menu:
2. Press 2.
3. Follow the steps in the appropriate section below. Each section
describes how to configure, activate, and enable the receiver for
a particular provider.
20.1 OmniSTAR
To use an OmniSTAR subscription service:
1. Identify the OmniSTAR coverage beam for your location.
2. Configure the DGPS source on the receiver.
3. Configure the provider name and coverage beam on the
receiver.
4. Activate the subscription.
For more information about each of these steps, see the following
instructions.
Note – OmniSTAR can be activated over the air only. The AgGPS 252
does not support manual activation (where OmniSTAR provides you
with a usercode).
Contact the service provider for the correct satellite coverage beam for
your geographic location.
In the US and Canada, contact OmniSTAR at 1- 888-883-8476
(www.omnistar.com).
You will need to provide a serial number and user code:
1. Navigate to the Serial number screen.
Record the serial number here:
2. Navigate to the Omni* screen.

Record the user code here:
To configure the DGPS Source for the subscription service:

1. In the DGPS Config sub-menu, navigate to the DGPS Source
screen.
3. Press 2 until Satellite Only, OmniSTAR VBS, or OmniSTAR

HP appears.
5. Press 5 to return to the DGPS Config sub-menu.
To configure the provider name and the correct satellite coverage
beam:
1. From the DGPS Config sub-menu, press 2 until the EZ Sat
screen appears.
Note – The EZ Sat screen includes the Coverage Beam field and
the Geographic Location field.
2. Press 3 to activate the cursor.
3. Press 2 until the required provider (Omni*) appears.
4. To move to the next field, press 3.

5. Press 2 until the coverage beam for your location appears.
7. Press 5 to return to the DGPS Config sub-menu.
To activate the OmniSTAR DGPS subscription:
1. Contact OmniSTAR on 1-888-883-8476 (US or Canada).
Provide OmniSTAR with:
– your billing information
– user code
– satellite beam name
OmniSTAR will activate the receiver. Activation can take
5–30 minutes.
Note – To track the OmniSTAR satellite, the receiver must be

outside with a clear view of the sky, turned on, and configured
to receive OmniSTAR VBS or HP corrections.
2. Once the receiver is activated, the Home screen displays
“D/3D”:
20.1 WAAS/EGNOS
WAAS is a free satellite-based DGPS service that is available only in
North America. EGNOS is a free satellite-based DGPS service that is
available only in Europe. To use the WAAS/EGNOS DGPS signal,
you must first configure the receiver.
To configure the receiver to use WAAS/EGNOS DGPS:
1. From the DGPS Config sub-menu, press 2 until the DGPS
Source screen appears.
3. Press 2 until WAAS/EGNOS ONLY appears:
åæ DGPS Source
WAAS/EGNOS ONLY
To enable the WAAS/EGNOS DGPS signal:
1. Press 2 until the WAAS/EGNOS T2 Remap screen appears.
3. Press 2 until On appears:
åæ WAAS/EGNOS
T2 Remap On
Configuring the Receiver to Operate in RTK Mode
4. To save the changes, press 4.

To enable WAAS reception in the field:
1. Take the receiver outside. Make sure that it has a clear southeast
and southwest view of the sky.
2. Switch on the receiver.
WAAS activation can take two or more minutes.
3. Once activation succeeds, the Home screen displays “D/3D”:
D/3D í07 DOP03

WAAS 122 ÷ø04
2.1 Configuring the Receiver to Operate in RTK Mode

Use AgRemote software to configure the receiver for operation in
RTK mode.
Note – Your receiver must have the RTK option enabled to operate in
this mode. This option is not supported by all receivers.
To configure the receiver:
1. Connect the receiver to the computer. Turn on the receiver and
start the AgRemote software.
2. In AgRemote, select Configuration / DGPS Config.
3. Set the Source Select field to RTK.
4. Press 4 then 5 to complete this part of the procedure.
5. For RTK operation, connect the radio to a receiver port. Change
the port input settings for that port to RtkLnk.
Configuring Beacon DGPS
2.1 Configuring Beacon DGPS

Follow these instructions to change an AgGPS receiver to Beacon
mode.
Note – Beacon DGPS mode is not supported by all receivers.
Select the frequency of the channels to be used when receiving RTCM
SC-104 broadcasts from radiobeacons:
1. Navigate to the DGPS Source screen.
2. If the screen does not display Beacon Only, press 3 to select
the Data Source field. Then press 2 until Beacon Only
appears.
4. Press 2 until the Beacon Mode screen appears:
5. Press 3 to activate the cursor. Press 2 until the required

beacon mode appears. See Table 7.
Table 7 Beacon modes
Mode name Description

Auto Range mode Reads the incoming RTCM SC-104 message
stream and selects the two closest
radiobeacons within range of the AgGPS
receiver. The closest radiobeacon is
automatically assigned to Beacon DGPS
Channel 0, and the second closest is assigned
to Channel 1.
Auto Power mode Detects the signal strength of the two most
powerful radiobeacons within range of the
AgGPS receiver. The most powerful
radiobeacon is automatically assigned to
Beacon DGPS Channel 0, and the second is
assigned to Channel 1.
Table 7 Beacon modes (continued)
Mode name Description

Disabled mode Disables DGPS and forces the AgGPS receiver
to operate in GPS mode only.
Manual Freq mode Disables the automatic selection of
radiobeacons so that you can manually select
the frequency of radiobeacons for Channel 0
and 1.
6. If you selected:
– Auto Range Mode or Auto Power Mode, configuration is
complete. Press 5 several times to return to the Home
screen.
The receiver automatically detects the two closest or two
most powerful beacons.
– Manual Freq Mode, see EZ Bcn screens, page 37, or
Manually selecting frequencies, page 38.
– Disabled Mode, the receiver ignores incoming
RTCM SC-104 messages and operates as a GPS-only
receiver.
EZ Bcn screens
The EZ Bcn 0 and EZ Bcn 1 screens use information in RTCM SC-104
broadcasts to create a list of beacon stations that are within range of
the receiver.
To manually select frequencies for Beacon Channels 0 and 1:
1. Navigate to the EZ Bcn 0 screen.
2. Press 3 to select the field for Beacon Channel 0.
3. Press 2 or 1 until the required beacon station appears:

5. Press 2. The EZ Bcn 1 screen appears.
6. To select the station for Beacon Channel 1, repeat Step 2
through Step 4.
Manually selecting frequencies

Note – Use this method only if you cannot find the required
radiobeacon name in the list.
To manually select Beacon DGPS radiobeacon frequencies using the
EZ Bcn screens:
1. Navigate to the Man Bcn Freqs screen.
2. Press 3. This activates the cursor in the Beacon Channel 0
field:
3. To enter the frequency one number at a time, press 2 or 1.

Press 3 to move to the next digit.
5. Press 3 to select the Beacon Channel 1 field.
6. To enter the other required frequency, repeat Step 3.
Installing Passcodes
2.1 Installing Passcodes

Passcodes are installed on AgGPS receivers to enable extra options or
to enable a firmware upgrade.
To install a passcode using AgRemote software:
1. Start AgRemote. See page 7.
2. From the Home screen, press 2 until the Update Receiver
screen appears:
3. Press 4.
4. Press 2 or 1 until the first digit of the passcode appears.
5. Press 3 to enter the digit and select the next digit.
6. Repeat Step 4 and Step 5 until all digits are entered.
7. Press 4 and then 2 to finish entering the passcode and exit
the screen.
Navigation Maps
2.1 Navigation Maps

The menus and screens that appear in AgRemote depend on the
receiver and firmware that you are using and the options you have
installed.
For a diagram (navigation map) of the menus and screens that are
available for each receiver, refer to the receiver documentation, or
contact your local Trimble reseller.

AgRemote RevA Guide ENG

Uploaded by

Copyright:

Available Formats

AgRemote RevA Guide ENG

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AgRemote RevA Guide ENG

Uploaded by

Copyright:

Available Formats

AgRemote Software

Guide for AgGPS Receivers

2.2 Downloading and Installing AgRemote

22.1 Downloading the install software from the Web

4. Choose a folder on the hard drive of your computer.

20.1 Installing the software in your computer

2.1 Starting AgRemote

Figure 1 shows the AgRemote window, the Home screen, and

Esc Enter Up Down Right Left

Figure 1 AgRemote window, Home screen, and navigation keys

Figure 2 shows a typical AgRemote Home screen. The information

Number of GPS satellites being tracked

Position type Current PDOP value

Correction type Signal-to-Noise ratio

DGPS satellite name or ID

Figure 2 Home screen

2.1 AgRemote Keys

The action associated with each of the AgRemote keys depends on

Key Action when a menu is displayed Action when a screen is displayed

1 Move up a menu level. Move up through the screens in a menu.

3 Move horizontally through the upper- Select the next alphanumeric or

2.2 Navigating Menus and Screens

Figure 3 shows the structure of a typical sub-menu (accessed from the

Figure 3 Typical sub-menu structure (Display Options)

To move between screens, press 2 or 1. When Ð appears in a

Receiver Option Details field

Figure 4 Example of a display-only field

For example, multiple-choice fields appear in the EZ Sat DGPS

Satellite Provider field

Satellite Coverage Beam field

Figure 5 Examples of multiple-choice fields

Alpha, numeric, and alphanumeric fields

An example of a numeric field appears in the Satellite Freq screen. See

Satellite Frequency field

Figure 6 Example of a numeric field

2.1 Positioning Mode

21.1 General GPS position information

D/3D í07 DOP03

Number of GPS satellites (SVs) being tracked

Figure 7 GPS status

Table 2 Position types (continued)

RTK mode status indicators

CMR Q:%86 A:2.0

Quality indicator: percentage of good RTK

Receiver is using CMR RTK corrections.

Figure 8 RTK mode status indicators

Satellite DGPS mode status indicators

Frequency for tracked DGPS satellite. Available

Receiver is using Satellite DGPS corrections.

Figure 9 Satellite DGPS mode status indicators

Table 3 shows the possible satellite differential mode indicators.

WAAS/EGNOS DGPS mode status indicators

WAAS 122 ÷ø07

Receiver is using WAAS/EGNOS corrections.

Figure 10 WAAS DGPS mode status indicators

Beacon DGPS mode

The beacon frequency. Frequency varies

The beacon operating mode.

Indicates the receiver is using beacon DGPS.

Figure 11 Beacon DGPS status