Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 5 views

    FNW.60R

    Uploaded by

    Michael Marroquin

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    FNW.60R

    Uploaded by

    Michael Marroquin
    5 views3 pages

    Original Title

    09. FNW.60R

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    5 views3 pages

    FNW.60R

    Uploaded by

    Michael Marroquin

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    Figure 60R

    RESILIENT SEATED
    KNIFE GATE VALVE
    Valve features
    The figure 60R is a wafer flat-face flanged, bi-directional
    knife gate valve. It is suitable for a wide range of
    industrial applications, including abrasive slurry services.
    The full port design has no internal obstructions and
    provides a “blind flange” shut off when closed. The
    valve’s sealing surface is between two thick resilient
    sleeves that are compressed into the valve housing. Two
    stainless steel stiffener rings are molded into the sleeves
    to locate it into the valve housing and to help the sleeves
    resist the high shearing forces present when the gate is
    driven between them. The body serves as an external
    guide to the valve knife gate. When in the open
    position, the stainless steel gate is completely withdrawn
    from the process flow and can be inspected and
    replaced, if necessary, without taking the valve out of Bidirectional
    service. The basic simplicity and open design of the
    Resilient
    valve invites an extremely wide range of options and
    accessories that can be tailored to specific applications. Seated

    Standard Features:
    Standard features of the figure 60R include:
    • Cast body, yoke, and packing follower
    • “Pop In” resilient seat sleeves (Install in the full open
    position)
    • Thrust ball bearing yoke bushing for reduced handwheel
    torque on 6” and larger valves
    • Bonnetless, outside screw and yoke, rising stem with stem
    cover and stem boot
    • Available in sizes from 3” to 30” diameter
    • Positive shut-off in both directions
    • For applications up to 100 PSI CWP

    “Pop In”
    Resilient Seats

    4120 N.E. Columbia Blvd. • Portland Oregon USA 97211


    Phone: 503-287-8383 • Fax: 503-281-9677 • www.fnwvalve.com
    Options Standard Materials
    FNW Valve Company offers many options and Ref. No. Description Material Qty Remarks
    modifications for valves. These include, but are not 1 Body A216 WCB 1
    limited to: 2 Disc A240 316 1
    3 Yoke A216 WCB 1
    • Splash guard with clean out
    4 Stem A276 410 1
    • Actuation including chain wheels, square drive nuts, 5 Body Seat GUM 2
    gear-operators, pneumatic & hydraulic cylinders, and 6 Packing PTFE Impregnated Fiber 1 Set Non-Asbestos
    motor operators 7 Packing Gland A216 WCB 1
    8-1 Gland Bolt STEEL 1 Set
    • Packing options for pH and temperature requirements 8-2 Gland Nut STEEL 1 Set Nylon Lock Nut
    • Stem extension and non-rising stem (NRS) adapters 9-1 Yoke Bolt STEEL 4
    in carbon and stainless steel 9-2 Yoke Nut STEEL 4
    10-1 Clevis Bolt A193 B8 2
    10-2 Clevis Nut A194 8 2 Nylon Lock Nut
    Standards 11 Yoke Sleeve BRASS 1
    12 Yoke Ring A36 1
    All valves are manufactured to the following 13 Hand Wheel A197 1
    dimensional and test standards. 14 Name Plate ALUMINUM 1
    15 Lock Washer A240 304 1
    • Face to Face Per - MSS SP-81
    16 Wheel Nut BRASS 1
    • End Flanges Per - ANSI B16.5 17 Lock Cap A276 304 1
    • Test Procedure Per - MSS SP-81 18 Rivet ALUMINUM 2
    19 Grease Nipple ASS’Y 1
    20 Lock Cap Nut A194 8 1 Nylon Lock Nut
    21 Thrust Ball Bearing ASS’Y
    22 Bearing Gland A36 1 Tack Weld
    23-1 Boot GUM RUBBER 1
    23-2 Boot Clamp A240 304 2
    24 Stem Cover A120 1
    25 Bottom Cover STEEL 1
    * Coincides with dimensional drawing number.

    Flow Coefficients, Port Areas, and Weights


    Port Area Weight Port Area Weight
    Size Cv (In2) (Lbs) Size Cv (In2) (Lbs)
    3 310 6.29 36 14 6,290 139.90 382
    4 530 11.22 51 16 8,240 184.00 479
    6 1,220 26.32 73 18 10,360 232.23 554
    8 2,160 47.15 137 20 12,780 286.08 693
    10 3,330 73.71 177 24 18,510 416.35 827
    12 4,780 105.81 210 30 29,070 659.27 1,590
    Valve port IDs available on dimensional drawing (d).

    Figure Number Matrix


    FNW 6 0 R X

    SIZE CODES
    3=M 14 = 14
    4=P 16 = 16
    6=U 18 = 18
    8=X 20 = 20
    For other valve materials or configurations, contact 10 = 10 24 = 24
    FNW Valve at (503) 287-8383 for sales assistance. 12 = 12
    FOR SIZES 6" AND LARGER

    Dimensions (Inches)
    Size D H I L W
    3 2.83 23.78 5.12 2.28 (2.00) 9.84
    4 3.78 28.07 5.67 2.28 (2.00) 11.81
    6 5.79 35.63 7.36 2.52 (2.25) 11.81
    8 7.75 40.75 8.66 3.03 (2.75) 15.75
    10 9.69 48.78 10.04 3.03 (2.75) 15.75
    12 11.61 55.35 11.34 3.27 (3.00) 15.75
    14 13.35 64.76 12.44 3.27 (3.00) 19.69
    16 15.31 69.84 13.94 3.78 (3.50) 21.65
    18 17.20 76.65 15.35 3.78 (3.50) 21.65
    20 19.09 79.25 16.61 4.68 (4.50) 23.62
    24 23.03 92.48 18.98 4.68 (4.50) 23.62
    30 28.98 112.20 22.83 5.00 (4.75) 30.70

    4120 N.E. Columbia Blvd. • Portland Oregon USA 97211


    Phone: 503-287-8383 • Fax: 503-281-9677 • www.fnwvalve.com

    You might also like