Two-Way Radio Model MT 750

ENGLISH This equipment is intended for use in:

AT CY FI IE LU PT
Combination
BA CZ FR IS MK RO
Speaker/Microphone/ DE GB SE
BE IT MT
Charging Jack BG DK GR LT NL SI
CH EE HR LV NO SK
CS ES HU LI PL TR
Antenna Countries of use

POWER Button
VOLUME CONTROL
Buttons

LOCK Button

CHANNEL CONTROL
Buttons
TALK Button

LIGHT/MAX RANGE

Printed in Philippines Part No. 480-263-P Version A

MODE Button
Button
Charger

Call Button

Speaker/
Microphone

Product Features
Keystroke Tone
• Two-Way Radio
with up to a 5 km (3 mile) range Battery Low Indicator
Lock
• 8 Channels*
• 38 CTCSS Privacy Codes Roger Beep
• Backlit LCD Display
• Water Resistant Scan
• Battery Saver Circuitry Receive/
Dual Watch
• Maximum Range Extender Transmit
VOX
• VOX Mode for Hands-Free Transmissions
• Baby Monitor Function Baby Monitor
Main Channel
• Call Alert (5 Selectable Tones) Number
• Scan (Channel, Privacy Code) CTCSS Privacy
• Dual Watch Programmable 2-Location Scan Power Saver Code Numbers
• Key Lock
• Auto Squelch
• Selectable On/Off "Roger Beep"
Confirmation Tone
• Selectable On/Off Keystroke Tone
• Combination Speaker/Microphone/Charging Jack
• Belt Clip Belt Clip
*You are not allowed to use channels 1 and 2 in France.
This situation can change; please contact the French radio licensing
authority for more information.

Wrist Strap
Connection Location

Battery Compartment

Lock Tab

Downloaded from www.Manualslib.com manuals search engine

 OPERATION English

Product Information Each port can charge one radio. Uses 230 volt
This microTALK® radio has been manufactured to adaptor. Use only Cobra NiMH batteries, model
meet all required standards for radio equipment GA-3ANH with charger model PA-CD3.
using PMR 446 frequencies as authorized. The Cobra recommends your radio is turned Off while
use of this two-way radio product involves the being charged.
public airways and its use may be subject to local
laws or regulations. Contact your radio licensing
Radio Power
authority for more information. To Turn Your Radio On: Power Button
– Press and hold the POWER
Caring for Your Radio button until you hear a
Your microTALK® radio will give you years of series of audible tones
trouble-free service if cared for properly. Here are indicating that the radio
a few suggestions: is On.
• Handle the radio gently. Your microTALK® radio is now in LISTENING MODE,
• Keep it away from dust. ready to receive transmissions. The radio is always
• Never put the radio in water or in a damp place. in LISTENING MODE, except when the TALK, CALL
• Avoid exposure to extreme temperatures. or MODE buttons are pressed.
To Turn Your Radio Off:
Desktop Charger and – Press and hold the POWER button.
Rechargeable Batteries
To Insert Batteries in Battery Low Indicator
Remove Belt Clip
Radio: When battery power is low, Battery Low

1. Remove belt clip by the BATTERY LOW indicator

releasing belt clip latch and will blink, indicating that
sliding clip up. batteries should be recharged
Lock Tab or replaced.
2. Pull down on lock tab to
remove battery cover (on WARNING: Only the supplied NiMH batteries
back of radio). can be recharged.

3. Insert GA-3ANH batteries Insert Batteries Battery/Power Saver

according to polarity markings. If there are no transmissions Power Saver
NOTE: Estimated operation time within ten (10) seconds, the
on full charge: 12 hours. unit will automatically switch
These rechargeable batteries to Battery Save Mode and
must be recycled or disposed of properly in POWER SAVER will appear in
compliance with all applicable laws. They must the display. This will not affect the unit’s ability
not be thrown in the rubbish bin. Some countries to receive incoming transmissions.
and local authorities require recycling and have
established collection programs. Please contact Communicating with
your local waste disposal authority for instructions. Another Person
WARNING: Do not put batteries into fire or expose To Talk To Another Person:
to high heat. They may explode. 1. Press and hold the TALK Talk Button
For Charging Cobra’s microTALK® button.
Radio(s): 2. With the microphone about
1. Insert radio(s) into the Insert Radio(s) 5 cm (2 inches) from your
charger as shown. mouth, speak in a normal
5 cm (2 Inches)
2. Insert round connector of voice. From Mouth
230 volt adaptor into jack 3. Release the button when
on back of charger. you have finished talking
3. Plug 230 volt adaptor into and listen for a response.
mains socket. You cannot receive incoming
If charging light is not On, check position of radio. calls while pressing the TALK button.
Radio should be upright. NOTE: Both radios must be tuned to the same
The charge indicator light will stay On as long as channel and privacy code to communicate.
the radio is in the charging well, even after the
batteries are fully charged.
It normally takes about 15 hours to fully recharge
batteries. Batteries will not be damaged if they
stay in the charging well longer than that.

Downloaded from www.Manualslib.com manuals search engine

 OPERATION English

Listening for a Response Display Illumination

When You Have Finished Talking: To Illuminate Your Display:
– Release the TALK button Listening – Press and release the Light/Max Range
to receive incoming LIGHT/MAX RANGE button Button

transmissions. Your to illuminate the display for

microTALK® is always in ten (10) seconds.
LISTENING MODE except
when the TALK, CALL or MODE Auto Squelch/
buttons are pressed. Maximum Range Extender
Your microTALK® radio is equipped with Auto
Volume Volume Buttons Squelch, which automatically shuts off weak
To Adjust the Volume: transmissions and unwanted noise resulting from
– Press the VOLUME UP or terrain, conditions, or from reaching your
the VOLUME DOWN maximum range limit.
buttons. You can temporarily turn Off Auto Squelch or turn
Volume Level
A triple beep sound is used to On Maximum Range Extender, allowing all signals
indicate that you have reached to be received and extending the maximum range
the minimum (1) or maximum of your radio.
(8) volume level. To Temporarily Turn Off Auto Squelch:
Call Button – Press the LIGHT/MAX Light/Max Range
RANGE button for less than Button
To Alert Another Person That You five (5) seconds.
Are Calling:
If you hear two (2) beeps,
– Press and release the CALL Call Button
you have turned the
button. Maximum Range Extender On
The other person will hear a (see below).
two (2) second ringing tone.
You cannot receive
transmissions while sending a call.

NOTE: Both radios must be tuned to the same To Turn Maximum Range Extender On:
channel and privacy code to communicate. – Press and hold the LIGHT/MAX RANGE button
for at least five (5) seconds until you hear two
Channels (2) beeps, indicating that the Maximum Range
To Select a Channel: Extender is On.
– With the radio ON, select Channel Buttons To Turn Maximum Range Extender Off:
any of the 8 channels by – Press and release the LIGHT/MAX RANGE
pushing the CHANNEL UP or button or change channels.
CHANNEL DOWN button.
You can press and hold the microTALK® Range
Channels
CHANNEL UP or CHANNEL Your microTALK® radio has a range of up to five
DOWN button for fast advance. (5) kilometres (3 miles). Your range will vary
NOTE: Both radios must be depending on terrain and conditions.
tuned to the same In flat, open country your Maximum Range
channel and privacy radio will operate at
code (see “CTCSS Privacy Codes”) maximum range.
to communicate. Buildings and foliage in the
path of the signal can
Lock Function reduce the range. Reduced Range
The LOCK button locks the CHANNEL UP, CHANNEL Dense foliage and hilly
DOWN, MODE and POWER buttons to prevent terrain will further reduce
accidental operation. the signal.
To Use the Lock Function: Remember, you can achieve Reduced Range
– Press and hold the LOCK Lock Button maximum range by using
button for two (2) seconds Maximum Range Extender.
to turn the Lock On or Off. See above for details.
A double beep sound is used to
confirm your Lock On or Off
Lock Icon
request. When the radio is in
Lock Mode, the Lock icon will
be displayed.

Downloaded from www.Manualslib.com manuals search engine

 OPERATION and
MODE FUNCTIONS English

Combination To Select a Privacy Code:

Speaker/Microphone/Charging Jack 1. After selecting a channel, Mode Button

Your microTALK® radio can be fitted with an press and release the MODE
external speaker/microphone, freeing your hands button until the small
for other tasks. This same jack also serves as the numbers next to the channel
connecting point for an optional wall number flash on the display.
Select
charger/adaptor. 2. Press the CHANNEL UP or Privacy Code
To Attach a Speaker/Microphone: CHANNEL DOWN button to
1. Open the speaker/ select a privacy code.
Speaker/
microphone/charging Microphone/ You can press and hold the
tab on the top of your Charging Jack CHANNEL UP or CHANNEL
microTALK radio.
® DOWN button for fast Channel Buttons
advance through CTCSS
2. Insert the plug into the
privacy code numbers.
speaker/microphone/
charging jack. 3. When your desired privacy
code is displayed, choose
To Connect a Wall Charger/Adaptor:
one of the following:
1. Open the speaker/microphone/charging tab
a. Press the MODE button to enter the new
on top of your microTALK® radio.
setting and proceed to other functions.
2. Insert the wall charger/adaptor plug into
b. Press the LOCK button to enter the new
the speaker/microphone/charging jack.
setting and return to LISTENING MODE.
c. Do not press any buttons for fifteen (15)
seconds to enter the new setting and return
to LISTENING MODE.

Scrolling Through the Mode Voice Activated Transmit (VOX)

Functions In VOX Mode, your microTALK® radio can be used
By scrolling through the Mode Functions, you will “hands-free,” automatically transmitting when you
be able to select or change preferred features of speak. You can set the VOX sensitivity level to fit
your microTALK® radio. While you are scrolling the volume of your voice and avoid transmissions
through the Mode Functions, your radio features triggered by background noise.
will be displayed in the same predetermined order: To Turn VOX Mode On or Off:
Set CTCSS Privacy Codes 1. Press the MODE button until Mode Button
Set VOX On/Off the VOX icon flashes on the
Set VOX Sensitivity Level display. The current On or
Set Channel Scan Off setting is displayed.
Set CTCSS Privacy Code Scan 2. Press the CHANNEL UP or
Program Dual Watch Location or CHANNEL DOWN button to Select VOX

Set Dual Watch On/Off turn VOX On or Off.

Set Baby Monitor 3. When your desired VOX
Set Call Tones Mode setting is displayed,
Set “Roger Beep” On/Off choose one of the Channel Buttons
Set Keystroke Tones On/Off following:
CTCSS Privacy Codes a. Press the MODE button
CTCSS (Continuous Tone Coded Squelch System) is to enter the new setting
an advanced tone coding system allowing you to and proceed to other
select one of 38 privacy codes to reduce incoming functions.
transmissions from other users on the channel. b. Press the LOCK button to enter the new
NOTE: If you are using a privacy code, both radios setting and return to LISTENING MODE.
must be tuned to the same channel and c. Do not press any buttons for fifteen (15)
privacy code to communicate. Each channel seconds to enter the new setting and return
will remember the last privacy code to LISTENING MODE.
you selected.

Downloaded from www.Manualslib.com manuals search engine

 MODE FUNCTIONS
OPERATION English
To Set the VOX Sensitivity Level: During An Incoming Transmission,
1. Press the MODE button until Mode Button You Can Choose From The Following:
the VOX icon flashes and a. Press and hold the TALK button to
the current sensitivity level communicate on that channel. Your radio will
is displayed. remain on that channel and return to
The current sensitivity level is LISTENING MODE.
Select VOX
displayed with the letter “L” Sensitivity Level
b. Press the CHANNEL UP or CHANNEL DOWN
and a number 1 to 5, 5 being button to resume scanning channels.
the most sensitive level and 1 If you press the TALK button while scanning and
being the least sensitive level. not within ten (10) seconds of receiving a
2. Press the CHANNEL UP or transmission, you will transmit on the channel on
CHANNEL DOWN button to Channel Buttons which you last received a transmission. This will
change the setting. return the radio to LISTENING MODE.
3. When your desired VOX If you do not press any button within ten (10)
sensitivity level is displayed, seconds, your radio will automatically resume
choose one of the scanning channels.
following: During Scanning (while not receiving
a. Press the MODE button to enter the new a transmission), You Can Choose From
setting and proceed to other functions. The Following:
b. Press the LOCK button to enter the new a. Press and hold the TALK button to
setting and return to LISTENING MODE. communicate on either the channel or
c. Do not press any buttons for fifteen (15) channel/privacy code that was displayed
seconds to enter the new setting and return before you entered Mode Functions or the
to LISTENING MODE. channel on which, during scanning, you last
received a transmission. This will return the
radio to LISTENING MODE.
b. Press the MODE button to proceed to set
CTCSS privacy code on the channel that was
either displayed before you entered Mode

Channel Scan Functions or on which, during scanning, you last

Your microTALK® radio can automatically scan received a transmission (see “CTCSS Privacy Code
channels (1 to 8). Scan” for further details).
NOTE: The radio ignores specific CTCSS privacy c. Press the LOCK button to return to
codes while scanning channels. LISTENING MODE on either the channel or
channel/privacy code that was displayed
To Scan Channels:
before you entered Mode Functions or the
1. Press the MODE button until Mode Button channel on which, during scanning, you last
the Scan icon and the transmitted or received.
channel number flash on
the display. CTCSS Privacy Code Scan
2. Press the CHANNEL UP or Select Scan Channels Your microTALK® radio can automatically scan
CHANNEL DOWN button to the CTCSS privacy codes (01 to 38) within
begin scanning channels. one (1) channel. Select Channel
The Scan icon will continue to To Scan Privacy Codes:
be displayed when channel 1. While in LISTENING MODE,
scan is On. Your radio will Channel Buttons
press the CHANNEL UP or
continue to scan all channels CHANNEL DOWN button to
and stop if an incoming choose the channel on Mode Button
transmission is detected. Your which you wish to scan the
radio will remain on that CTCSS privacy codes.
channel for ten (10) seconds. 2. Press the MODE button
While setting channel scan, if you do not press until the Scan icon and the Select Scan Privacy
any buttons for fifteen (15) seconds your radio small numbers next to the Codes
will automatically return to LISTENING MODE on channel number flash on
the channel or channel/privacy code displayed the display.
before you entered Mode Functions. 3. Press the CHANNEL UP or
CHANNEL DOWN button to
Channel Buttons
begin scanning CTCSS
privacy codes within the
channel you selected.

Downloaded from www.Manualslib.com manuals search engine

 MODE FUNCTIONS
OPERATION English
The Scan icon will continue to be displayed when Dual Watch
CTCSS privacy code scan is On. Your radio will Dual Watch allows you to simultaneously monitor
continue to scan CTCSS privacy codes and stop as any two (2) Dual Watch Locations:
an incoming transmission is detected. Your radio
Dual Watch Location 1 – is always the
will remain on that channel/privacy code for ten
channel/privacy code displayed before
(10) seconds.
you entered Mode Functions. See
While setting CTCSS privacy code scan, if you do “Channels” and “CTCSS Privacy Codes”
not press any buttons for fifteen (15) seconds sections for further details.
your radio will automatically return to LISTENING
Dual Watch Location 2 – will be stored in the
MODE on the channel/privacy code that was
radio. It can be edited and/or recalled for
displayed before you entered Mode Functions.
future engagements of Dual Watch Mode.
During An Incoming Transmission,
To Program Or Edit Dual Watch
You Can Choose From The Following:
Location 2 And Engage Dual Watch
a. Press and hold the TALK button to Mode:
communicate on that channel/privacy code.
1. Press the MODE button Mode Button
Your radio will remain on that
until the Dual Watch icon
channel/privacy code and return
and the channel number
to LISTENING MODE.
flash on the display.
b. Press the CHANNEL UP or CHANNEL DOWN
2. Choose one of the
button to resume scanning CTCSS privacy Select Dual Watch
following:
codes.
a. Select or edit a channel:
If you press the TALK button while scanning
and not within ten (10) seconds of receiving 1) Press the CHANNEL
a transmission, you will transmit on the UP or CHANNEL
channel/privacy code on which you last received DOWN button to Channel Buttons

a transmission. This will return the radio to select a channel

LISTENING MODE. (1 to 8).

If you do not press any button within ten (10) b. Select or edit a channel/privacy code:
seconds, your radio will automatically resume 1) Press the CHANNEL UP or CHANNEL
scanning CTCSS privacy codes. DOWN button to select a channel
During Scanning (while not receiving (1 to 8).
a transmission), You Can Choose From 2) Press the MODE button to set the
The Following: channel. The small numbers next to the
a. Press and hold the TALK button to channel number will flash on the display.
communicate on either the channel 3) Press the CHANNEL UP or CHANNEL
or channel/privacy code that was DOWN button to select a CTCSS privacy
displayed before you entered Mode code (00 to 38).
Functions or channel/privacy code 3. Press the LOCK button to Lock Button
on which, during scanning, you last set Dual Watch Location 2
received a transmission. This will return and engage DUAL WATCH
the radio to LISTENING MODE. MODE (see below for
b. Press the MODE button to proceed to next further details).
available Mode Function. NOTES: To terminate Dual Watch and proceed
c. Press the LOCK button to return to to the next available Mode Function,
LISTENING MODE on either the channel or press the MODE button.
channel/privacy code that was displayed While setting Dual Watch Location 2,
before you entered Mode Functions or the if you do not press any buttons for fifteen
channel/privacy code on which, during (15) seconds your radio will automatically
scanning, you last received a transmission. return to LISTENING MODE on Dual Watch
Location 1.

Downloaded from www.Manualslib.com manuals search engine

 MODE FUNCTIONS
OPERATION English
To Turn Dual Watch On: During Dual Watch (while not receiving
NOTE: Dual Watch Location 2 must be a transmission), You Can Choose From
programmed to turn Dual Watch on. The Following:
1. Set the first Dual Watch Select Channel a. Press and hold the TALK button to
Location (channel/privacy communicate on either Dual Watch Location
code) you wish to monitor 1 or the last Dual Watch Location on which,
(see “Channels” and during Dual Watch, you last received a
“CTCSS Privacy Codes” transmission. This will return the radio to
sections for further details). LISTENING MODE.
2. Press the MODE button until Mode Button b. Press the MODE button to proceed to
the Dual Watch icon and the other functions.
channel number flash on c. Press the LOCK button to return to
the display. LISTENING MODE on either Dual Watch
NOTE: While setting Dual Location 1 or the last Dual Watch Location
Watch, if you do not press any buttons on which, during Dual Watch, you last
for fifteen (15) seconds your radio will received a transmission.
automatically return to LISTENING MODE To Terminate Dual Watch:
on the last channel or channel/privacy Choose one of the following:
code displayed before you entered a. Press the LOCK button to return to
Mode Functions. LISTENING MODE on either Dual Watch
3. Press the LOCK button Lock Button Location 1 or the last Dual Watch Location
to engage DUAL WATCH on which, during Dual Watch, you last
MODE. received a transmission.
b. Press the TALK button to return to
LISTENING MODE on either Dual Watch
Location 1 or the last Dual Watch Location
on which, during Dual Watch, you last
received a transmission.

During An Incoming Transmission, c. Press the MODE button and proceed to the
You Can Choose From The Following: next available Mode Function.
a. Press and hold the TALK button to
communicate on that Dual Watch Location.
Your radio will remain on that Dual Watch
Location and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN
button to resume Dual Watch.
If you press the TALK button while in Dual Watch
and not within ten (10) seconds of receiving a
transmission, you will transmit on the last Dual
Watch Location on which you received a
transmission. This will return the radio to
LISTENING MODE.
If you do not press any button within ten (10)
seconds, your radio will automatically resume
Dual Watch.

Downloaded from www.Manualslib.com manuals search engine

 MODE FUNCTIONS
OPERATION English

Baby Monitor 3. When your desired call tone setting is

With the Baby Monitor Function on, a radio left displayed, choose one of the following:
near a baby will transmit to another unit on the a. Press the MODE button to enter the new
same channel and privacy code whenever a sound setting and proceed
is detected. Baby Monitor uses the same to other functions.
sensitivity level you set for the VOX Function. If b. Press the LOCK button to enter the new
you have not set a VOX sensitivity level (see the setting and return to LISTENING MODE.
“Voice Activated Transmit [VOX]” section of this c. Do not press any buttons for fifteen (15)
manual), the maximum sensitivity level 5 will seconds to enter the new setting and
automatically be used. return to LISTENING MODE.
To Turn Baby Monitor On:
1. Press MODE button until the Mode Button
"Roger Beep" Confirmation Tone
Baby Monitor icon flashes Your listener will hear an audible tone when
on the display. The current you release the TALK button. This alerts the other
Off setting is displayed. party that you have finished talking and that it is
2. Press the CHANNEL UP or OK for them to speak. This feature can be turned
CHANNEL DOWN button to
Select Baby Monitor On or Off.
change the setting to On. To Turn “Roger Beep” On or Off:
3. Press the LOCK button to When you turn On your microTALK® radio for the
enter the On setting and first time, “Roger Beep” will be On.
enter BABY MONITOR MODE. Channel Buttons 1. Press and release the MODE Mode Button
NOTES: Pressing the MODE button until the “Roger
button will enter the Beep” icon flashes on the
Baby Monitor Mode display. The current On or
setting as Off and Off setting is displayed.
Lock Button Select Roger Beep
proceed to other 2. Press the CHANNEL UP or
Mode Functions. CHANNEL DOWN button
to select “Roger Beep”
On or Off.

Not pressing any buttons for fifteen (15) 3. When your desired Roger Channel Buttons
seconds will enter the Baby Monitor Mode Beep Mode setting is
setting as Off and return the radio to displayed, choose one
LISTENING MODE. of the following:
NOTE: Both radios must be tuned to the same a. Press the MODE button
channel and privacy code to communicate. to enter the new setting and proceed
To Terminate Baby Monitor Mode: to other functions.
Choose one of the following: b. Press the LOCK button to enter the new
a. Press the TALK button and return to setting and return to LISTENING MODE.
LISTENING MODE. c. Do not press any buttons for fifteen (15)
b. Press the LOCK button and return to seconds to enter the new setting and return
LISTENING MODE. to LISTENING MODE.
c. Press the MODE button and proceed to The setting you select will be saved when you
the next available Mode Function. turn your radio off and on again. When the
“Roger Beep” is On, the “Roger Beep” icon
5 Call Tone Settings will be displayed.
You can choose between five (5) different call
tone settings to transmit a unique call alert.
To Change a Call Tone Mode Button
Setting:
1. Press the MODE button
until the letter “C” and the
current call tone number
Call Tone Setting
(1 to 5) is displayed. The
current call tone will sound
for two (2) seconds.
2. Press the CHANNEL UP
or CHANNEL DOWN button Channel Buttons
to hear the other call
tone settings.

Downloaded from www.Manualslib.com manuals search engine

 MODE FUNCTIONS
OPERATION English

Keystroke Tones 3. When your desired Keystroke Tone Mode

With Keystroke Tones turned On, your radio will setting is displayed, choose one of the
sound beeps each time you press a button or following:
change a setting. a. Press the MODE button to enter the new
To Turn Keystroke Tones On or Off: setting and return to LISTENING MODE.
When you turn On your microTALK® radio for the b. Press the LOCK button to enter the new
first time, Keystroke Tones will be On. setting and return to LISTENING MODE.
1. Press the MODE button until Mode Button c. Do not press any buttons for fifteen (15)
the Keystroke Tones icon seconds to enter the new setting and return
flashes on the display. The to LISTENING MODE.
current ON or OFF setting The setting you select will be saved when you
is displayed. turn your radio off and on again. When Keystroke
2. Press the CHANNEL UP or Select Keystroke Tones are On, the keystroke tone icon will
CHANNEL DOWN button to be displayed.
turn Keystroke Tones On
or Off.
Channel Buttons

D.O.C., WARRANTY
& CUSTOMER SERVICE English
Declaration of Conformity Warranty & Customer Service
This declaration is the responsibility of the manufacturer/importer For warranty and customer service information,
Cobra Electronics Europe Limited please contact your local dealer.
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
Date: 21 November 2005
This certifies that the following designated product For use in EU countries, subject to local laws
PRIVATE MOBILE RADIO: MT 750 and regulations.
(Product Identification) CEEL™ is a trademark of Cobra Electronics
complies with the essential protection requirements of R & TTE Corporation, USA.
Directive 1999/5/EC on the approximation of the laws of the Snake design and microTALK® are registered
Member States relating to Radio Spectrum Matters, EMC and trademarks of Cobra Electronics Corporation, USA.
Electrical Safety. ©2006 Cobra® Electronics Europe Limited
This declaration applies to all specimens manufactured in accordance Dungar House, Northumberland Avenue
with the attached technical documentation described in Annex II of Dun Laoghaire, County Dublin, Ireland
the Directive which forms part of this declaration.
www.cobra.com
Assessment of compliance of the product (class 2.6) with the
requirements relating to the essential requirements according to
Article 3 R & TTE was based on Annex IV of Directive 1999/5/EC
and the following standards:
Radio Spectrum: EN 300 296-1 V1.1.1 (2001-03)
EN 300 296-2 V1.1.1 (2001-03)
EMC: EN 301 489-1 V1.4.1 (2002-08)
EN 301 489-5 V1.3.1 (2002-08)
Electrical Safety: IEC 60950-1:2001 /
EN 60950-1:2001
RF Exposure: EN 50392 (2004-02)

DUBLIN, IRELAND MIKE KAVANAGH

Downloaded from www.Manualslib.com manuals search engine