series

features
28 Ton (24,4 mton) Capacity 4-Section 102' (31,0 m) Proportional Boom 4-Section 92' (28.0 m) Proportional Boom 2-Section 26' (7,9 m) to 46' (14,0 m) Telescopic Jib 157' (47,85 m) Maximum Tip Height with Telescopic Jib 111' (33,83 m) Maximum Main Boom Tip Height 19' 8", (6 m) Out-and-Down Outriggers at Full Extension Intermediate and Fully Extended Outrigger Charts are Standard 2-Speed Planetary Hoist with Grooved Drum and Negative Draft Flange Load Moment Indicator with Digital Display, CAN Bus, Overload Shutdown and Internal Boom Length Cable Radio ATB Rugged, Weatherproof Electrical System with Circuit Status LEDs Removable Boom Rest System Pressure Gauge Continuous Rotation Clamp-On Mounting Aeroquip STC (Snap to Connect) Hydraulic Fittings Manitex UPTime Comprehensive Support

2802
T R U C K S

B O O M

product guide

series
G E N E R A L
BOOM Booms Inverted T-cross section, 4-section telescoping type, extended and retracted proportionally by a double-acting hydraulic cylinder and cable-crowd system. Easily replaceable and adjustable high-density nylon slide pads. 28102S 4-Section 28' 0" (8,5 m) to 92' 0" (28,0 m). 2-Section 26' (7,9 m) to 46' (14,0 m) jib. Quick Reeve Boom Point Three high-density nylon load sheaves mounted on heavy-duty roller bearings. Two removable pin-type rope guards. Boom Elevation Double-acting hydraulic cylinder. Working range from 9 below horizontal to 80 above. Load Hook 5-ton (4,5 mton) capacity hook with heavy-duty swivel and weight is provided for single-line operation. HOIST Hoist Maximum theoretical line speed 247 fpm (75,3 mpm). Maximum theoretical bottom-layer line pull 11,500 lb (5 227 kg). Two-speed planetary reducer. Spring applied, pressure-released internal brake. Wire Rope 335' (102,1 m) of 9/16" (14,3 mm) diameter 6 X 25 EIPS IWRC. SWING SYSTEM Continuous rotation is standard. Externally mounted, double-reduction planetary driven by hydraulic motor. Maximum swing speed 1.5 rpm. Springapplied hydraulically-released parking brake. Ball-bearing swing circle with external gear. OUTRIGGERS Fully extended, intermediate extension and fully retracted positions. Out-and-down type with double-acting hydraulic cylinders operated independently for precise leveling. Bubble level located near outrigger controls. MOUNTING Mounting Lower frame is mounted to chassis by threaded rods and clamp plates. No welding to truck chassis is required. 12" (305 mm) diameter.

2802
Rear Underride Protection Supplied on factory mounted cranes. Fabricated structure mounted under rear of carrier. Complies with Bureau of Motor Carrier Safety Standard 393.86. Lower Frame Torsion resistant, rigid 4-plate design with integrated outrigger and pedestal. Boom Rest Heavy-duty fabrication. Easily removed to simplify loading and unloading truck deck. CONTROL SYSTEM Single operator platform and seat mounted to turret. Four single-axis crane controls, bubble level and system pressure gauge arranged to ANSI B30.5 standards. The operator station includes engine start/stop, air foot throttle, signal horn, load moment indicator console, boom-angle indicator, load chart and range diagram. Optional pilot operated controls not available on units configured with radio remote controls. HYDRAULICS Hydraulic System A 3-section vane pump direct-mounted to power take-off on truck transmission provides 32 gpm to the hoist, 21 gpm to the boom hoist and telescope circuit, and 8 gpm (80 lpm) to the swing and outrigger circuit. 70-gallon (265-liter) baffled reservoir with strainer and 25-micron filter in the return lines. Ball-type shutoff valve and strainer are provided in suction line. All fittings are ORS type and SAE. Aeroquip STC (Snap- to-Connect) on all hoses up to 1" virtually eliminates leaks. Hydraulic Cylinders All load-holding cylinders are equipped with integral holding valves. WARNING SYSTEMS Load Moment Indicator (LMI) CAN bus system maximizes expansion capabilities. Senses boom hoist cylinder pressure, boom length and boom angle. Audio-visual warning indicated overload conditions and overload shutoff feature prevents continuing overload. Operator can access all load conditions via display at the operator station. Internal boom length cable. Radio Anti-Two-Block System Audible warning and shutoff functions prevent hook from contacting boom point. Back-Up Alarm Electronic audible motion alarm activated when truck transmission is in reverse gear. GENERAL Electrical State-of-the-art, weather-resistant components throughout. Hermetically sealed power in relays. Enclosure includes power in relays and circuit status LEDs. Designed to withstand high pressure washing and varying climates. Design/Welding Design conforms to ANSI B30.5. Welding conforms to AWS D1.1. Tested to SAE 1063 and SAE 765. Manuals Operator, service and parts manuals depict correct crane operation, maintenance procedures and parts listing. Warranty 12-month warranty covers parts and labor resulting from defects in material and workmanship. * In order to ensure continuous improvement, specifications may change without notice.

S P E C I F I C AT I O N S

30' 5.75" 9,29 m Retracted 101' 11.75" 31,08 m Extended 226.75" 5759 mm

17.00" 432 mm 4' 2.75" 1041 mm

4' 3.5 1,31 m 14' 3.25 4,35 m 41.00" 1041 mm

AF

27.04" 687 mm 59.66" 1515 mm WB 253.00" 6426 mm

208.02" 5284 mm CT 184.00" 4674 mm

16.13" 410 mm 34.84" 885 mm AF 93.00" 2362 mm

OAL 33' 10" 10,31 m

CHASSIS DATA
Wheelbase (WB)

28102S/2892S 253" 6 426 mm 184" 4 674 mm 93" 2 362 mm 20.0 in 110,000 psi 758 422 kPa 20.0 in3 110,000 psi 758 422 kPa 18,000 lb 8 182 kg 34,000 lb 15 455 kg 8,400 lb 3 810 kg 8,300 lb 3 773 kg 34" 864 mm
3

MAXIMUM TIP HEIGHT

28102S Boom 102' 31,1 m 111' 9" 34,1 m 138' 42,1 m 157' 9" 48.1 m

2892S Boom 92' 28 m 101' 9" 31 m 128' 39 m 147' 9" 45 m

Cab to Tandem (CT)

After Frame (AF) Frame Section Modulus at 180 Area of Operation Frame Section Modulus at 360 of Operation Front Axle Gross Weight Rating

Extended Jib

Rear Axle Gross Weight Rating Minimum Truck Axle Weight Front** Minimum Truck Axle Weight Back** Nominal Frame Width

See Range Diagram

80

*Frame section modulus at 360 area of operation requires front bumper stabilizer. **Minimum chassis weight is required to meet 85% stability requirements. Chassis data is general not for engineering. Some dimensions depend on truck selection.

WEIGHTS
Cab Alone Crane (Without Cab) 14' (4,27 m) Flat Bed 26' (7,92 m) Fixed Length Jib 26' (7,92 m) to 46'(14,02 m) Telescopic Jib

28102S 575 lb 261 kg 23,100 lb 10 478 kg 1,260 lb 573 kg 832 lb 378 kg 1,226 lb 557 kg

2892S 575 lb 261 kg 22,392 lb 10 157 kg 1,260 lb 572 kg 832 lb 377 kg 1,226 lb 557 kg 8.00" 203 mm 236.00" 5994 mm 8.06" 205 mm 10

OAH 12' 3 .5" 3,75 m

OAH CT CA WB OAL BBC

Overall Height Cab to Tandem Cab to Axle Wheel Base Overall Length Bumper to Back of Cab Afterframe

USE THIS CHART ONLY WHEN OUTRIGGERS AND STABILIZERS ARE FULLY EXTENDED.

51,8 170 48,8 160 45,7 150 42,7 140 39,6 130 80

75 70 65 60 55 50 45

HEIGHT ABOVE GROUND ft. m

Pins must be disengaged for this outrigger configuration.

All outrigger beams must be extended to full extend mark.

36,6 120 33,5 110 30,5 100 27,4 90 24,4 80 21,3 70 18,3 60 15,2 50 12,2 40 9,1 30 6,1 20
D 102 31,1 C 85 25,9 B 68 20,7 A 51 15,5

40 35 30

Boom must be fully retracted when jib is erected, before lowering through this area

25 20

This mark indicates beam is fully extended.

15 10 5 0

236.00 REF (19' 8")

OPERATING RADIUS FROM CENTERLINE OF ROTATION ft. m

FULLY EXTENDED OUTRIGGER SPREAD: MODEL 28102S MAIN BOOM LOAD RATINGS
Boom Length Operating Radius Feet Meters 5 8 10 12 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 30.5 Feet 9,29 Meters lb. kg. A 51 Feet 15,54 Meters lb. kg. B 68 Feet 20,72 Meters lb. kg. C 85 Feet 25,90 Meters lb. kg. D 102 Feet 31,08 Meters lb. kg. Fixed Jib 26 Feet 7,92 Meters lb. kg.

JIB LOAD RATINGS

1,52 2,43 4,04 3,65 4,57 6,09 7,62 9,14 10,66 12,19 13,71 15,24 16,76 18,28 19,81 21,33 22,86 24,38 25,90 27,43 28,96 30,48 32,00

80 56,000 25 454 75 39,690 18 040 71 33,510 15 231 79 22,500 10 227 67 29,120 13 236 77 22,500 10 227 60 23,260 10 572 73 21,710 9 868 79 20,590 9 359 48 16,530 7 513 33 12,410 5 640 67 16,910 7 686 61 12,870 5 850 54 10,110 4 595 47 38 27 8,130 3 695 6,630 3 013 5,450 2 477 74 15,830 7 195 70 12,840 5 836 65 10,260 4 663 60 55 50 43 36 28 15 8,280 3 763 6,790 3 086 5,610 2 550 4,670 2 122 3,820 2 122 3,110 1 413 2,520 1 145 78 14,420 6 544 81 10,500 4 772 75 12,180 5 536 78 9,650 4 386 72 10,140 4 609 76 8,670 3 940 68 64 60 56 51 47 41 36 29 19 8,360 3 800 73 7,670 3 486 6,870 3 122 70 6,490 2 950 5,690 2 709 66 5,590 2 540 4,750 2 159 63 4,800 2 181 3,920 2 781 60 3,980 1 809 3,220 1 463 56 3,280 1 409 2,640 1 200 53 2,700 1 227 2,150 1,740 1,390 81 79 77 75 72 70 68 65 63 60 57 54 51 48 45 5,300 2 409 5,300 2 409 4,990 2 268 4,580 2 081 4,190 1 904 3,830 1 740 3,480 1 581 3,020 1 372 2,630 1 195 2,310 1 050 1,910 1,560 1,250 990 750 81 79 77 75 72 70 68 65 63 60 57 54 51 48 5,100 2 318 5,100 2 318 4,730 2 150 4,310 1 959 3,910 1 777 3,550 1 613 3,110 1 413 2,670 1 213 2,280 1 036 1,950 1,620 1,270 960 990 81 79 77 76 74 72 70 68 66 63 61 59 56 54 51 48 490 900 3,050 1 386 4,000 1 386 3,050 1 386 3,050 1 386 2,910 1 322 2,740 1 245 2,590 1 177 2,410 1 095 2,130 1,880 1,610 1,400 1,150 910 700 510

977 790 631

49 2,220 1 009 45 1,810 40 1,460 36 1,150 29 22 880 640

886 736 577 436 313

968 854 731 636 522 413 318 231

822 663 522 400 290

868 709 568 450 340

222 331

290 440

131 200

220 330

100 150

180 260

81 180

150 220

68 100

Deductions: Stowed Fixed Jib Deductions: Stowed Telescopic Jib

Meets ANSI B30.5 Requirements - Do not operate crane or accessories within 10' (3,05m) of live power lines. NOTICE: This chart is for reference only and must not be used for lifting purposes. Consult factory for other boom options.

AREA OF OPERATION

Standard 360 Full Capacity Work Area

DEDUCTIONS
Auxiliary Block Auxiliary Block Load Block Overhaul Ball 50 lb 22.72 kg 50 lb 22.72 kg See block manufacturer nameplate See overhaul ball manufacturer nameplate 140 lb 63.64 kg See load rating chart

WARNING
The front tires must be in contact with the ground and the machine level when operating in this area.

Hose Reel Swing Around Jib* (Stowed)

WEIGHTS
1 Part Line 2 Part Line 3 Part Line 4 Part Line 5 Part Line 6 Part Line 7 Part Line

WARNING

Anti-two-block system must be in good operating condition before operating crane. Refer to the owners manual. Keep at least three wraps of load line on the drum at all times.
.5625" rot resistant (5.0:1 SF) - 37000 lb. min. breaking strength .5625" 6 x 25 IWRC (3.5:1 SF) - 29750 lb. min. breaking strength

SINGLE SHEAVE BLOCK

SINGLE SHEAVE BLOCK

TRIPLE SHEAVE BLOCK

AUXILIARY BLOCK

AUXILIARY BLOCK

TRIPLE SHEAVE BLOCK

TRIPLE SHEAVE BLOCK

8,500 lb 3 864 kg 7,400 lb 3 364 kg

17,000 lb 7 727 kg 14,800 lb 6 727 kg

25,500 lb 11 591 kg 22,200 lb 10 091 kg

34,000 lb 15 455 kg 29,600 lb 13 455 kg

42,500 lb 19 318 kg 37,000 lb 16 818 kg

51,000 lb 23 182 kg 44,400 lb 20 182 kg

56,000 lb 25 455 kg 51,800 lb 23 545 kg

BOOM AND JIB COMBINATIONS 28102S 102' 4 Section Boom 26' 46' 2 - Section Jib

2892S

92'

4 Section

Boom

TRIPLE SHEAVE BLOCK

OVERHAUL BALL

AUXILIARY SHEAVE

AUXILIARY BLOCK

26' 46' 2 - Section Jib

UPTime is the Manitex commitment to complete support of thousands of units working every day.

Includes 24-7-365 parts shipments. Utilizes the efficiency of UPNet online parts order system. Relies on Manitexs UPTrak support tracking system for performance analysis and resource allocation. Features REMan, Manitexs cost effective rebuild/exchange program. Provides expert service technicians for troubleshooting and site visits. Mandates training; at our facility and yours. It includes coordinated support from all component suppliers. Involves every Manitex team member in the support of every Manitex customer. What does UPTime mean to Manitex customers?

UPTime means reliability. UPTime means utilization. UPTime means profitability.

Manitex 3000 South Austin Avenue P.O. Box 1609 Georgetown, TX, USA 786271609 Telephone 512-942-3000 Facsimile 512-863-3776 www.manitex.com

MTX 2802 09.03 TG 2,000