Simplex - Sx501 Addressable Sensors International Use Only

Addressable Sensors
The Addressable Sensors are for use in an addressable system, using

the MX Digital Protocol, where sensors are placed in key areas around
the building. The sensor measures environmental parameters and
sends the values to the fire alarm control panel. The control panel
processes incoming data to decide if an alarm needs to be issued.
Depending on the model, environmental variables monitored are one
or a combination of:
 Temperature
 Smoke Density
 Concentration of Carbon monoxide (CO), used either in Toxic Gas
mode or Fire Detection mode (not both)
Detector Order Number

Photo / Heat Sensor 4098-6255
Photoelectric Sensor 4098-6256
Heat Sensor 4098-6257
Functions and Base compatibility

Self Monitoring - The sensors are able to identify the following faults:
 Heat (temperature) sensor. A normal output level is expected, around “ambient temperature”.
 CO sensor. The integrity of the sensor cell is monitored.
 Optical (smoke) sensors. The optical chamber is periodically stimulated.
Self testing - Fire conditions are artificially simulated in the detector to prompt a fire response.
Status indicator - The status indicator has 3 states:
 Yellow flashing: a sensor fault.
 Red flashing: normal operation (flashes on detector poll). This can be enabled/disabled using the panel configuration software.
 Red continuous: the sensor is in alarm.
Remote LED: The sensors are capable of driving a Remote LED.
Address Programming: By docking the sensor into an 801AP MX Service Tool or an 850EMT, you can programme the sensor’s address.
Installation
Base
The Addressable Sensors are installed by fitting into a specially designed base. Features of the base are:
 Detector Locking - The locking pin prevents unauthorised removal of the detector head.
 Lock release - A suitable tool is inserted into the access hole on the detector cover to release the locking pin.
 Park Position - Securely holds the detector in the base without making electrical contact.
Fitting a detector
1 Install and connect base wires according to instructions supplied with the base.
2 Identify the raised rib alignment markers on the edges of the detector and base.
3 Position the detector marker approximately 15mm/15° anticlockwise from the base marker.
4 Rotate the detector to mate it to the base. Ensure the detector rib and base rib are aligned with each other.
1/2 Doc. version 1.0

Simplex Addressable Sensors with Isolator
Summary Table
The following table shows the features, functions and characteristics of the models in this product series.
Model Name 4098-6255 4098-6256 4098-6257
Heat  
Smoke (optical)  
CO
Self Monitoring   
Self-Test   
Status Indicator   
Remote LED   
Functional Base Compatibility   
Short Circuit Line Isolator   
Remote Programming   
Loop Continuity (Base)   
CO Toxic Gas Mode
Threshold Compensation  
Fast Logic 
Compatible with Standard Base 4B 4B 4B
0.081 0.076 0.076

KG
Operating temperature (°C) -25 to +70 -25 to +70 -25 to +70
Storage temperature (°C) -40 to +80 -40 to +80 -40 to +80
Operating/Relative humidity 95% (non-condensing)
Dimensions Height: 42 mm Diameter: 108 mm
Material Body, cover, and closure: White flame Retardant ABS
Characteristics For use in an addressable system with MX Digital Protocol
Position Do not expose to direct sunlight
IP Rating IP44 in accordance with BS EN 60529:1992 + A2:2013
Approvals
EUROPEAN
CPR APPROVAL TYPE
APPROVALS
CPR
DETECTOR ORDER NUMBER
Declaration of Performance
EN54-17
EN54-5
EN54-7
LPCB
Photo / Heat Sensor 4098-6255 DOP-2015-4104    

Photoelectric 4098-6256 DOP-2015-4105   
Sensor
Heat Sensor 4098-6257 DOP-2015-4106   
All required Declarations and certificates are publically available on the website www.simplex-fire.com and are searchable by number or model name.
The above fire detection products are components designed for use in Addressable Systems exclusively available to registered partners only. They are intended for installation
by trained registered personnel only. Systems should be installed and configured according to local regulations.
120.515.916_SPX-D-830-DS. doc. version 1.0. 29. June 2018.

© 2018 Johnson Controls. All rights reserved. All specifications and other information shown were current as of
document revision date and are subject to change without notice.
www.simplex-fire.com
Tyco Fire & Security GmbH, Victor von Bruns-Strasse 21, 8212 Neuhausen am Rheinfall, Switzerland

Simplex - Sx501 Addressable Sensors International Use Only

Uploaded by

Copyright:

Available Formats

Simplex - Sx501 Addressable Sensors International Use Only

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Simplex - Sx501 Addressable Sensors International Use Only

Uploaded by

Copyright:

Available Formats

Addressable Sensors

The Addressable Sensors are for use in an addressable system, using

Detector Order Number

Photoelectric Sensor 4098-6256

Heat Sensor 4098-6257

Functions and Base compatibility

1/2 Doc. version 1.0

Functional Base Compatibility   

Short Circuit Line Isolator   

Loop Continuity (Base)   

CO Toxic Gas Mode

Compatible with Standard Base 4B 4B 4B

0.081 0.076 0.076

Operating temperature (°C) -25 to +70 -25 to +70 -25 to +70

Storage temperature (°C) -40 to +80 -40 to +80 -40 to +80

Operating/Relative humidity 95% (non-condensing)

Dimensions Height: 42 mm Diameter: 108 mm

Material Body, cover, and closure: White flame Retardant ABS

Characteristics For use in an addressable system with MX Digital Protocol

Position Do not expose to direct sunlight

IP Rating IP44 in accordance with BS EN 60529:1992 + A2:2013

Photo / Heat Sensor 4098-6255 DOP-2015-4104    

120.515.916_SPX-D-830-DS. doc. version 1.0. 29. June 2018.

You might also like