BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH ,
POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 1
Unit No and Name: Chapter 1: Introduction to Design
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level Define machine design. W20 PO1 Q1. CO1 PSO1 1 2 State four types of loads acting PO1 Q2 CO1 PSO1 1 2 on machine elements. What do you mean by creep? PO1, Q3 CO1 PSO1 1 2 Define Ergonomics. PO1, Q.4 CO1 PSO1 1 2 PO3 State the theories of elastic failure. Explain maximum normal stress PO1, Q.5 theory and maximum shear CO1 PSO1 2 4 PO3,PO5 stress theory with equations.
Define :i) Resilience
ii) Modulus of resilience. Show PO1,
Q6 CO1 PSO1 1 4 modulus of resilience on stress-strain diagram for ductile material.
Draw stress – strain diagram for PO1,
Q7 brittle material. CO1 PSO1 2 4 PO3,PO4 write the material specification i) Fe E 230 ii ) X20Cr 18 Ni 2 PO1, Q8 CO1 PSO1 2 4 iii )35 C 8 PO5 iv) 40 Ni 2 Cr 1 Mo 20 TSSM’S BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH , POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 2 Unit No and Name : Chapter 2: Design of Joints, Levers & Offset Links
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level Draw neat sketch of Turn Buckle. PO1, Q1. CO1 PSO1 2 4 PO3 Why taper is provided on cotter ? PO1,PO2 Q2 CO1 PSO1 1 4 State recommended values of taper. Draw neat sketch showing the details of cotter joint. State Two PO1,PO3 Q3 strength equations. CO2 PSO1 2 6
Explain Knuckle Joint with
neat sketch PO1,PO3 Q.4 CO2 PSO1 2 6
Give two applications of knuckle PO1,PO5
Q.5 joint. CO1 PSO1 2 4 TSSM’S BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH , POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 3 Unit No and Name : Chapter 3: Design of Shafts, Keys and Couplings
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level
PO1 Q1. State the classification of shaft CO1 PSO1 1 4 couplings What are the requirement of a good PO1,PO2 Q2 coupling? CO1 PSO1 1 4
Give the Effect of Keyway on PO1,PO2
Q3 CO1 PSO1 2 4 strength of shaft State four types of keys. PO1,PO2 Q.4 CO1 PSO1 1 4 PO3, State any four factors to be consider PO1,PO2 Q.5 while selecting the coupling CO2 PSO1 1 4 PO3 Why a coupling should be placed as PO1,PO2 Q.6 CO2 PSO1 2 4 close to a bearing as possible? PO3, Prove that, for square key, PO1,PO2 Q7 permissible crushing stress is twice CO2 PSO1 3 6 PO3,PO4 the permissible shear stress
Design a rectangular key to be used
PO1,PO2 Q8 for a shaft of diameter 50 mm. Both CO3 PSO1 6 4 PO3,PO4,PO6 are having the same material. Take fs=42 Mpa & fc=70 Mpa TSSM’S BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH , POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 4 Unit No and Name : Chapter 4: Design of Power Screws
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level Why Square threads are preferred PO1,PO2 Q1. over V-thread for power transmission CO1 PSO1 2 4 PO4,PO6 Explain Efficiency of self-locking PO1,PO2 Q2 screw is less than 50 %. CO1 PSO1 2 4 ,PO4,PO6 Why Square threads are preferred over V-thread for power PO1,PO2 Q3 CO1 PSO1 2 4 transmission. ,PO4,PO6
Give the design procedure of screw PO1,PO2
Q.4 CO2 PSO1 2 6 and nut of a screw jack. PO3,PO4
Write Lewis equation for the
strength of gear tooth. Give the PO1,PO2 Q.5 CO2 PSO1 3 6 meaning of each term. PO3,PO4
Explain the following modes of
failure of gear tooth : PO1,PO2 Q6 i) Pitting CO2 PSO1 2 PO3,PO4 ii) Scoring iii) Abrasive wear Give the nomenclature of bolt PO1,PO2 Q7 CO1 PSO1 1 4 PO3,PO6 What are different modes of failure PO1,PO2 Q.8 of Gear CO1 PSO1 2 4 PO3, TSSM’S BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH , POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 5 Unit No and Name : Chapter 5: Design of springs
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level Write classification of spring and PO1,PO2 Q1. Give Application of spring CO1 PSO1 3 4 PO3,
Sketch of Leaf Spring of semi PO1,PO2
Q2 CO1 PSO1 3 4 elliptical Type
Define the terms :
i) Solidlength ii) ii) Free length PO1,PO2 Q3 CO2 PSO1 1 iii) Springindex PO3,PO4 iv) Pitch, w.r. to helical compression spring. State four desirable properties of PO1,PO2 Q.4 spring CO1 PSO1 1 4 PO3,PO4,PO6 Explain Wahl’s correction factor PO1,PO2 Q.5 CO2 PSO1 2 6 PO3,PO4 A helical spring is made from a wire of 8 mm diameter and has outside diameter 90 mm; if the permissible shear stress is 350 N/mm2 and modulus of rigidity 84 kN/mm2, find the axial load which the spring can PO1,PO2 Q.6 carry and the deflection per active CO3 PSO1 3 6 PO3,PO4 turn.
i) Neglecting the effect of curvature.
ii) Considering the effect of curvature. TSSM’S BHIVARABAI SAWANT COLLEGE OF ENGINEERING AND RESEARCH , POLYTECHNIC, NARHE,PUNE-41 ACADEMIC YEAR 2024-25 DEPARTMENT OF MECHANICAL ENGINEERING
=============================================================== Semester V - Subject & Sub Code: Elements of Machine Design(22564)
Assignment- 6 Unit No and Name : Chapter 7: Design of Threaded and Welded Joints and Antifriction bearing
Question Mapping Number Blooms
Question Statement Marks No CO PO PSO Level State Advantages& disadvantages of welded joints over riveted PO1,PO2 Q1. CO1 PSO1 1 4 joints: PO3,
State Advantages of ball bearings PO1,PO2
Q2 CO1 PSO1 1 4 over plain journal bearing PO3,
State Disadvantages of rolling
bearing as compared to Journal PO1,PO2 Q3 CO1 PSO1 1 4 Bearing PO3
Draw symbolic representation of
following types of weld : PO1,PO2 Q.4 i) Double V butt joint CO2 PSO1 3 4 PO3,PO4 ii) Double ‘U’ butt joint iii) Single level butt iv) Spot Give Advantages& disadvantages of PO1,PO2 Q.5 CO1 PSO1 1 4 welded joints over riveted joints. PO3 How will select bearing from manufacturer catalogue? PO1,PO2 Q.6 CO2 PSO1 1 4 PO3,PO4
State and explain any four properties PO1,PO2
Q7 CO1 PSO1 1 4 of sliding contact bearing material PO3 State classification of bearing PO1,PO2 Q8 CO1 PSO1 1 4 ,PO7
