Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 10 views

    Model Question Paper - Set-1: Industrial Automation

    Uploaded by

    anamayank111
    Zjzmmz

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Model Question Paper - Set-1: Industrial Automation

    Uploaded by

    anamayank111
    10 views2 pages
    Zjzmmz

    Original Title

    5042

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Zjzmmz

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    10 views2 pages

    Model Question Paper - Set-1: Industrial Automation

    Uploaded by

    anamayank111
    Zjzmmz

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    TED (21) – 5042 REVISION 2021

    FIFTH SEMESTER DIPLOMA EXAMINATION IN ENGINEERING


    AND TECHNOLOGY

    INDUSTRIAL AUTOMATION
    MODEL QUESTION PAPER – SET-1

    Time: 3 hours Maximum Marks: 75

    PART A

    I. Answer all the following questions in one word or sentence.


    (9 x 1 = 9 Marks)
    Module Outcome Cognitive level

    1 The angle at which SCR starts conducting is called …….. M1.03 U


    2 Draw the symbol of IGBT and name the terminals. M1.01 R
    A device that converts fixed DC I/p to variable DC o/p
    3 M2.04 U
    voltage is called ………..
    ….……is a device that provides backup power when regular
    4 M3.04 U
    power source fails or voltage drops to an unacceptable level.
    5 List any 2 disadvantages of Stator Voltage Control method. M3.02 R
    6 PLC means ………………………………………….. M4.01 R
    In a ladder diagram normally open contacts in parallel
    7 M4.03 U
    represents …… function.
    8 Write any two applications of Induction heating. M3.03 R
    9 What is the reason for controlled rectifiers. M2.01 R

    PART B

    II. Answer any Eight questions from the following


    (8 x 3 = 24 Marks)
    Module Outcome Cognitive level

    1 Develop ladder logic for Boolean expression Y=(AB+C)D M4.04 A

    2 Define the term Holding current and Latching current M1.01 R


    Draw the circuit of Half wave controlled rectifier with
    3 M2.01 U
    resistive load and its output response.
    4 List any 3 advantages of PLC over relays. M4.02 R
    Develop ladder diagram for a two way switch stair case
    5 M4.04 A
    lamp.
    6 List any 3 comparisons between AC and DC drives M3.01 R
    7 State the principle of Dielectric heating. M3.03 R
    8 Draw the circuit and output response of a step down chopper. M2.04 U

    9 With a neat sketch explain the two-transistor analogy of SCR M1.02 U

    10 Which UPS is better, ON-line or OFF-line and why. M3.04 R

    PART C

    III. Answer all questions from the following (6 x 7 = 42 Marks)


    Module Outcome Cognitive level

    1 a. With a neat sketch describe the structure of SCR M1.01 U

    1 b. List any 6 applications of SCR M1.01 R


    OR
    Draw the circuit and explain the working of UJT triggering of
    2 M1.03 U
    SCR
    3 With a neat sketch explain the working of power MOSFET. M1.01 U
    OR
    With circuit diagram explain the working of class-C
    4 M1.04 U
    commutation technique.
    5 With circuit diagram explain the working of Jone’s chopper. M2.04 U

    OR
    6 a. Explain the working of a Series inverter with circuit diagram M2.02 U

    List any 2 differences between a series inverter and a parallel


    6 b. M2.02 R
    inverter.
    Explain with necessary diagrams about the operation of a
    7 M2.01 U
    Centre Tapped Full Wave controlled rectifier with RL load.
    OR
    With a neat circuit diagram explain the working of a step-up
    8 M2.03 U
    Cyclo Converter.
    Draw the block diagram and explain the working of an ON-line
    9 M3.04 U
    UPS
    OR
    10 List and explain any 3 types of resistance welding. M3.03 U

    11 Explain about Program Control instructions used in PLC M4.03 U

    OR
    12 List the main parts of a PLC and write the function of each part. M4.01 U

    You might also like