Sony VX

HCD-VX8/VX8J
SERVICE MANUAL E Model
HCD-VX8/VX8J is the tuner, deck, CD and

amplifier section in MHC-VX8/VX8J. Photo: HCD-VX8 (SILVER)
Model Name Using Similar Mechanism HCD-GRX80/RXD8/RXD8S

CD CD Mechanism Type CDM38L-5BD34L
SECTION
Base Unit Type BU-5BD34L
Optical Pick-up Type KSS-213D/Q-NP
TAPE DECK Model Name Using Similar Mechanism HCD-GRX80/RXD8/RXD8S
SECTION Tape Transport Mechanism Type TCM-230AWR2/230PWR2
SPECIFICATIONS
— Continued on next page —
COMPACT DISC DECK RECEIVER
MICROFILM
–1–
Downloaded from www.Manualslib.com manuals search engine
MODEL IDENTIFICATION
— BACK PANEL —
Parts No.
PARTS No. MODEL PRODUCT

COUNTRY
4-215-641-0π VX8: EA MALAYSIA
4-215-641-1π VX8: MY, SP MALAYSIA
4-215-641-2π VX8: TW MALAYSIA
4-215-641-3π VX8: E MALAYSIA
4-215-641-4π VX8: IA INDONESIA
4-215-641-5π VX8: HK MALAYSIA
4-215-641-6π VX8J: E JAPAN
4-215-641-7π VX8J: EA JAPAN
CAUTION 4-215-641-8π VX8: TH THAI
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous ra- • Abbreviation
diation exposure. EA : Saudi Arabia model
TW : Taiwan model
Notes on chip component replacement IA : Indonesia model
HK : Hong Kong model
• Never reuse a disconnected chip component.
TH : Thai model
• Notice that the minus side of a tantalum capacitor may be MY : Malaysia model
damaged by heat. SP : Singapore model
Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
circuit board (within 3 times). OR BASE UNIT
• Be careful not to apply force on the conductor when soldering
or unsoldering. The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
Laser component in this product is capable of emitting radiation During repair, pay attention to electrostatic break-down and also
exceeding the limit for Class 1. use the procedure in the printed matter which is included in the
repair parts.
This appliance is classified as The flexible board is easily damaged and should be handled with
a CLASS 1 LASER product. care.
The CLASS 1 LASER PROD-
UCT MARKING is located on NOTES ON LASER DIODE EMISSION CHECK
the rear exterior.
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
SAFETY-RELATED COMPONENT WARNING !! up block. Therefore, when checking the laser diode emission, ob-
serve from more than 30 cm away from the objective lens.
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN LASER DIODE AND FOCUS SEARCH OPERATION
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. CHECK
REPLACE THESE COMPONENTS WITH SONY PARTS
Carry out the “S curve check” in “CD section adjustment” and check
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
that the S curve waveform is output four times.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
–2–
TABLE OF CONTENTS
1. SERVICING NOTE .......................................................... 4 9. EXPLODED VIEWS

9-1. Case Section ........................................................................ 90
2. GENERAL .......................................................................... 5 9-2. Chassis Section ................................................................... 91
9-3. Front Panel Section ............................................................. 92
3. DISASSEMBLY 9-4. CD Mechanism Deck Section-1 (CDM38L-5BD34L) ....... 93
9-5. CD Mechanism Deck Section-2 (CDM38L-5BD34L) ....... 94
3-1. Loading Panel ....................................................................... 7
9-6. Base Unit Section (BU-5BD34L) ....................................... 95
3-2. Front Panel and Video Board ................................................ 7
9-7. TC Mechanism Section-1 (TCM230AWR2/230PWR2) .... 96
3-3. Cassette Lid and Tape Mechanism ........................................ 8
9-8. TC Mechanism Section-2 (TCM230AWR2/230PWR2) .... 97
3-4. CD SW Board and Panel Board ............................................ 8
3-5. Disc Tray ............................................................................... 9
10. ELECTRICAL PARTS LIST ............................. 98
4. SERVICE MODE ............................................................ 10
5. TEST MODE ..................................................................... 12
6. MECHANICAL ADJUSTMENTS .......................... 13
7. ELECTRICAL ADJUSTMENTS ............................... 13
8. DIAGRAMS
8-1. Circuit Boards Location ...................................................... 18
8-2. Block Diagrams
• CD Section ....................................................................... 19
• Video Section ................................................................... 21
• Deck Section .................................................................... 23
• Main Section .................................................................... 25
• Power Section .................................................................. 27
• Display Section ................................................................ 29
8-3. Printed Wiring Board – CD Section – ................................. 33
8-4. Schematic Diagram – CD Section – ................................... 35
8-5. Schematic Diagram – Deck Section – ................................. 37
8-6. Printed Wiring Board – Deck Section – .............................. 39
8-7. Printed Wiring Board – Video Section – ............................. 41
8-8. Schematic Diagram – Video (1/3) Section – ....................... 43
8-9. Schematic Diagram – Video (2/3) Section – ....................... 45
8-10. Schematic Diagram – Video (3/3) Section – .................... 47
8-11. Printed Wiring Board – Main Section – ........................... 49
8-12. Schematic Diagram – Main (1/4) Section – ..................... 51
8-16. Printed Wiring Board – Leaf SW Section – ..................... 59
8-17. Schematic Diagram – Leaf SW Section – ........................ 59
8-18. Printed Wiring Board – Panel Section – ........................... 61
8-19. Schematic Diagram – Panel (1/3) Section – ..................... 63
8-22. Schematic Diagram – CD Motor Section – ...................... 69
8-23. Printed Wiring Board – CD Motor Section – ................... 71
8-24. Schematic Diagram – Trans Section – ............................. 73
8-25. Printed Wiring Board – Trans Section – ........................... 75
8-26. Schematic Diagram – Surround Section – ....................... 76
8-27. Printed Wiring Board – Surround Section – ..................... 76
8-28. IC Block Diagrams ........................................................... 77
8-29. IC Pin Functions ............................................................... 80
–3–
SECTION 1
SERVICING NOTE
HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH
TURNS OFF
1 Remove the Case.
3 Pull-out the disc tray.
2 Turn the cam to the direction

of arrow.
NOTE FOR INSTALLATION (ROTARY ENCODER)
Note:When attaching the Base unit, Insert the

BU cam section A into the groove of BU cam.
Section A
Groove
Note:When attaching the BU cam,

engage the Rotary encoder
switch as shown in the figure.
CD-TEXT
This unit is provided with a simple CD-TEXT display function.
The CD-TEXT contents of 20 tracks are displayed on the fluorescent display tube.
Since the function is simple, some special characters may not be displayed, or may be displayed as other characters.
–4–
SECTION 2
GENERAL
Front Panel 1 2 3 4 5 6 7
64 8
63
62 9
61
10
60 11
58 57 56 55 54 59
53 52 51 50 12 13 14
49 48 47 46 15 16 17 18
19
45 44 43 42 20 21
41 40 39 38
37 36 22
35 23
33 32 34
24
25
26
27
28
31 30 29
LOCATION OF PARTS AND CONTROLS
1 1/u (Power) button and indicator 21 SURROUND button 43 BEAT SPEED button
2 DEMO (STANDBY) button 22 HI DUB button 44 BEAT SELECT button
3 DISC 1 button and indicator 23 CD SYNC button 45 BEAT ON/OFF button and indicator
4 DISC 2 button and indicator 24 VOLUME knob 46 P FILE MEMORY button
5 DISC 3 button and indicator 25 PHONES jack 47 GEQ CONTROL button
6 DISC SKIP/EX–CHANGE button 26 ENTER/NEXT button 48 FILE SELECT
7 § (Eject) button 27 ) + button and indicator 49 EFFECT button
8 Disc tray 28 JOG/0x) dial and indicator 50 NEXT button
9 EDIT DIRECTION/TUNER MEMORY 29 GROOVE button and indicator 51 PREV button
button 30 0 – button and indicator 52 RETURN button
10 PLAY MODE/DOLBY NR button 31 AUTO BPM button and indicator 53 SELECT button
11 REPEAT/STEREO/MONO button 32 PAD B button and indicator 54 ( (TAPE B) button and indicator
12 p button 33 PAD A button and indicator 55 9 (TAPE B) button and indicator
13 ^ (CD) button and indicator 34 MIC 2 jack 56 ( (TAPE A) button and indicator
14 TUNER/BAND button 35 MIC 1 jack 57 9 (TAPE A) button and indicator
15 CD NON-STOP button and indicator 36 CD FLASH button 58 FUNCTION button
16 KARAOKE PON/MPX button 37 CD LOOP button 59 Remote sensor
17 SYNC EQ button 38 MIC LEVEL knob 60 DISPLAY button
18 SYNC BASS button 39 JAM button and indicator 61 SPECTRUM ANALYZER button
19 REC PAUSE/START button and 40 LEVEL button 62 CLOCK/TIME SET button
indicator 41 MIX button 63 TIMER SELECT button and indicator
20 DBFB button 42 ECHO LEVEL knob 64 Display Window
–5–
–6–
instruction manual.
This section is extracted from

SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-1. LOADING PANEL
Claws
3 Loading panel
1 Turn the cam to the direction

of arrow.
3-2. FRONT PANEL AND VIDEO BOARD
!∞ Video board
!¢ Screw (BVTP 3x8)
!™ Flat type wire !¡ Flat type wire
(CN503) (CN501)
9 Flat type wire
(CN303)
8 Flat type wire !£ Two screws (BVTP 3x8)
2 Screw (BVTT 3x6) (CN304)
Lead wires
6 Screw (BVTP 3x10)
Lead wire
5 Screw
0 Front panel
(BVTP3x10)
1 Screw (BVTT 3x6)

7 Flat type wire
(CN501)
4 Screw (BVTT 3x6)
3 Screw (BVTT 3x6)
–7–
3-3. CASSETTE LID AND TAPE MECHANISM 9 Tape mechanism
8 Three screws
(BVTP2.6x8)
7 Two screws
(BVTP2.6x8)
6 Tension spring
4 Cassette holder (L)

assembly
Note for installation

Portion A
2 Release
(Refer to order No. 1)
Portion A
3 Cassette holder (R)
assembly 5 Tension spring
Portion B
1 Release
Portion B
3-4. CD SW BOARD AND PANEL BOARD
3 CD SW board 1 Three screws

(BVTP2.6x8)
2 Three screws
(BVTP2.6x8)
8 Flat type wire

(CN601)
4 Knob (Jog)
6 Nut
9 Four screws
(BVTP2.6x8)
0 Five screws
(BVTP2.6x8)
7 Nut !¡ Five screws

!™ Panel board (BVTP2.6x8)
5 Knob (Vol)
–8–
3-5. DISC TRAY
(Perform after removing the front panel.) Note:When installing the Disc tray, pull around the flat type wire to
pass through the claw A and claw B, as shown in the figure.
3 Flat type wire (8 core)
4 Two claws

5 Remove the disc tray. Claw B
Claw A
1 Turn the cam the

direction of arrow.
–9–
SECTION 4
SERVICE MODE
MC Cold Reset
• The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the
customer.
Procedure:
1. Press three buttons p , ENTER/NEXT , and 1/u simultaneously.
2. “COLD RESET” is displayed on the fluorescent display tube and reset is executed.
CD Delivery Mode
• This mode moves the optical pick-up to the position durable to vibration. Use this mode when returning the set to the customer after repair.
Procedure:
1. Press 1/u button to turn the set ON.
2. Press LOOP button and 1/u button simultaneously.
3. A message “LOCK” is displayed on the fluorescent indicator tube, and the CD delivery mode is set.
MC Hot Reset
• This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged
in and out.
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 1 simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously, and the set is reset.
Sled Servo Mode

• This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pick-up.
Procedure:
2. Press three buttons p , ENTER/NEXT , and § simultaneously.
3. The Sled Servo mode is selected, if “CD” is blanking on the fluorescent indicator tube.
4. With the CD in stop status, When the ) + button is pressed the optical pick-up moves outside. When – 0 button is pressed , it moves
inside.
5. To exit from this mode, perform as follows:
1) Move the optical pick-up to the most inside track.
2) Execute MC cold reset. (Press the three buttons p , ENTER/NEXT , and 1/u button simultaneously.)
Note:
• Always move the optical pick-up to most inside track when exiting from this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be chipped.
Change-over of AM Tuner Step between 9kHz and 10kHz

• A step of AM channels can be changed over between 9kHz and 10kHz.
Procedure:
2. Select the function “TUNER”, and press TUNER/BAND button to select the BAND “AM”.
3. Press 1/u button to turn the set OFF.
4. Press ENTER/NEXT and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM 9k STEP” or “AM
10k STEP”, and thus the channel step is changed over.
LED and Fluorescent Indicator Tube All Lit, Key Check Mode
Procedure:
1. Press three buttons p , ENTER/NEXT , and DISC 2 simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
Press DISC 2 button, and the key check mode is activated.
3. In the key check mode, the fluorescent indicator tube displays “K 0 V0 J0”. Each time a button is pressed, “K”value increases. However,
once a button is pressed, it is no longer taken into account.
“J” Value increases like 1, 2, 3 ... if rotating 0 AMS ) knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
“V” Value increases like 1, 2, 3 ... if rotating VOLUME knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in “-” direction.
4. To exit from this mode, press three buttons in the same manner as step 1, or disconnect the power cord.
– 10 –
AMS Test Mode
• This mode is used for checking the AMS operations of the tape deck.
JIG
7-819-039-12 Alignment tape, AMS-110A
Procedure:
1. Press the 1/u button to turn the unit ON.
2. Set the tape (AMS-110A).
3. Press the three buttons p , ENTER/NEXT , and DISC 3 button simultaneously.
4. “TEST MODE” is displayed on the fluorescent display tube.
5. Press the FUNCTION button and switch the function to the deck with the tape (AMS-110A).
6. Press the CD SYNC button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.
7. AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8.
“NG” is displayed at other times, and the deck stops.
8. AMS starts in the opposite direction. If the AMS count is 2 at shut down again, “OK” is displayed.
“NG” is displayed at other times.
Note: The p button of CD section will become effective and the aging of CD section will stop sometime, if the buttons described in step 3
are not pressed simultaneously. In that case, press ^ button and operate the CD section.
– 11 –
SECTION 5
TEST MODE
VIDEO CD COLOR-BARS MODE
On this mode, the data of the color-bars signal as a picture signal and the 1kHz sine wave signal as a sound signal are output by the
mechanism control microcomputer (IC502) for video CD signal check. When measurement of the voltage and waveform on the VIDEO
board, perform it in this mode.
For refernce, the color-bars signal can be observed at J302 (VIDEO OUT) and the sound signal can be observed at J101 (VIDEO/MD
(AUDIO) OUT) using an oscilloscope.
1. Connect the lead wire to both ends of the land of SL503 of the VIDEO board.
2. Turn the power on. Press FUNCTION button to select CD.
3. After 2 or 3 seconds later, connect the lead wire.
4. After measuring, remove the lead wire connected.
[VIDEO BOARD] (SIDE A)
D502
SL501 SL502 SL503
TEST MODE
IC505
CT503
VIDEO IC507
FREQUENCY
[VIDEO BOARD] (SIDE B)
SL503 IC502
TEST
SL502
MODE SL501
– 12 –
SECTION 6 SECTION 7
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution DECK SECTION 0 dB=0.775V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head damagnetizer.
record/playback heads pinch rollers 2. Do not use a magnetized screwdriver for the adjustments.
erase head rubber belts 3. After the adjustments, apply suitable locking compound to the
capstan idlers parts adjusted.
2. Demagnetize the record/playback head with a head demagne- 4. The adjustments should be performed with the rated power sup-
tizer. ply voltage unless otherwise noted.
3. Do not use a magnetized screwdriver for the adjustments. 5. The adjustments should be performed in the order given in this
4. After the adjustments, apply suitable locking compound to the service manual. (As a general rule, playback circuit adjustment
parts adjusted. should be completed before performing recording circuit adjust-
5. The adjustments should be performed with the rated power sup- ment.)
ply voltage unless otherwise noted. 6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
Torque Measurement specified.
Mode Torque meter Meter reading
Tape Signal Used for
31 to 71 g • cm
FWD CQ-102C (0.43 – 0.98 oz • inch) P-4-A100 10 kHz, –10 dB Azimuth Adjustment
FWD 2 to 6 g • cm
CQ-102C WS-48B 3 kHz, 0 dB Tape Speed Adjustment
back tension (0.02 – 0.08 oz • inch)
31 to 71 g • cm P-4-L300 315 Hz, 0 dB Level Adjustment
REV CQ-102RC
(0.43 – 0.98 oz • inch)
REV 2 to 6 g • cm
CQ-102RC Record/Playback Head Azimuth Adjustment
back tension (0.02 – 0.08 oz • inch)
71 to 143 g • cm (Deck A, Deck B)
FF/REW CQ-201B
(0.98 – 1.99 oz • inch)
100 g or more Note: Perform this adjustments for both decks.
FWD tension CQ-403A
(3.53 oz or more)
100 g or more Procedure:
REV tension CQ-403R
(3.53 oz or more) 1. Mode : Playback
test tape
P-4-A100
(10kHz, –10dB)
MD OUT level meter
set +
–
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.
L-CH
output
peak within
level
1 dB within 1dB
R-CH
peak
screw
position
screw
L-CH R-CH position
peak peak
– 13 –
3. Mode: Playback Tape Speed Adjustment (Deck A)
test tape
P-4-A100 Note: Set the test mode using the following method and begin tape
(10kHz, –10dB) speed adjustment.
oscilloscope In the test mode, the speed will switch to double speed or
MD OUT normal speed each time the HI DUB button is pressed.
set
Procedure:
With the power turned ON, press the p button, ENTER/NEXT
button, and DISC 3 button simultaneously.
(The “CD TYPE INDICATOR” on the fluorescent display tube will
blink while in the test mode.)
To exit the test mode, press the 1/u button.
Waveform of oscilloscope 1. Insert the WS-48B into deck B.

2. Press the ( button of deck B.
3. Press the HI DUB button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of
in phase 45° 90° 135° 180°
the frequency counter becomes 6000 ± 180 Hz.
good wrong 5. Press the HI DUB button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of
4. After the adjustments, apply suitable locking compound to the the frequency counter becomes 3000 ± 90 Hz.
parts adjusted.
Adjustment Location: LEAF SW board
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B) Sample Value of Wow and flutter
W.RMS (JIS) less than 0.3%
(test tape: WS-48B)
Playback Level Adjustment (Deck A, Deck B)
Procedure:
Mode: Playback
test tape
P-4-L300 level meter
(315Hz, 0dB)
set
Reverse Foward
MD OUT
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301

(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.
Adjustment level:
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
Adjustment Location
[LEAF SW BOARD]
RV1001(High Speed)
RV1002(Normal Speed)
RV1002 RV1001
– 14 –
Record Bias Adjustment (Deck B) Record Level Adjustment (Deck B)
Procedure: Procedure:
INTRODUCTION INTRODUCTION
When set to the test mode performed in Tape Speed Adjust- When set to the test mode performed in Tape Speed Adjust-
ment, when the tape is rewound after recording, the “REC memory ment, when the tape is rewound after recording, the “REC memory
mode” which rewinds only the recorded portion and playback is mode” which rewinds only the recorded portion and playback is
set. set.
This “REC memory mode” is convenient for performing this ad- This “REC memory mode” is convenient for performing this
justment. During recording, the input signal FUNCTION will auto- adjustment. During recording, the input signal FUNCTION will au-
matically switch to VIDEO. tomatically switch to VIDEO.
(After recording, press the – 0 button without stopping will (After recording, press the – 0 button without stopping will
return to the position where recording was started.) return to the position where recording was started.)
1. Press FUNCTION button to select VIDEO. (This step is not 1. Press FUNCTION button to select VIDEO 1. (This step is not
necessary if the above test mode has already been set.) necessary if the above test mode has already been set.)
2. Insert a tape into deck B, press the r REC button, and then 2. Insert a tape into deck B, press the r REC button, and then
press the ( button to start recording. press the ( button to start recording.
3. Mode: Record 3. Mode: Record
VIDEO (AUDIO) IN VIDEO (AUDIO) IN
1) 315 Hz 315Hz 50 mV (–23.8 dB)
} 50 mV (–23.8 dB)
2) 10 kHz
AF OSC
AF OSC blank tape
blank tape
600 Ω CS-123
600 Ω CS-123
attenuator
attenuator
set
set
4. Mode: Playback 4. Mode: Playback
recorded level meter recorded level meter

position position
set set
MD OUT MD OUT
5. Confirm playback the signal recorded in step 2 become adjust- 5. Confirm playback the signal recorded in step 2 become adjust-
ment level as follows. ment level as follows.
If these levels do not adjustment level, adjust the RV341 (L-CH) If these levels do not adjustment level, adjust the RV301 (L-CH)
and RV441 (R-CH) on the AUDIO board to repeat steps 3 and 4. and RV351 (R-CH) on the MAIN board to repeat steps 3 and 4.
Adjustment level: The playback output of 10 kHz level difference Adjustment level:
against 315 Hz reference should be ± 1.0 dB. CN403 playback level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
Adjustment Location: AUDIO board Adjustment Location: MAIN board
Adjustment Location: [MAIN BOARD] (Conductor Side)

Record Level (L CH)
[AUDIO BOARD] (Conductor Side)
RV301
RV341(Lch),RV441(Rch) RV311(Lch),RV411(Rch) 43 42
Record Bias Playback Level (Deck A) 56 29
1 28 IC301
14 15
CN303
RV351
RV301 RV401 Record Level (R CH)
RV411
RV441 RV341 RV311
RV301(Lch),RV401(Rch)
Playback Level (Deck B)
– 15 –
Note: Clear RF signal waveform means that the shape “◊” can be
CD SECTION
clearly distinguished at the center of the waveform.
Note: RF signal waveform
1. CD Block is basically constructed to operate without adjustment.
Therefore, check each item in order given. VOLT/DIV : 200mV
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TIME/DIV : 500ns
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent when
level : 1.75 ± 0.25 Vp-p
the signal level is low than specified value with the following
checks.
S Curve Check
oscilloscope
E-F Balance (Traverse) Check
BD board oscilloscope
BD board
TP (FE) +
TP (VC) – TP (TE) +
TP (VC) –
Adjustment Location: BD board

Adjustment Location: BD board
Procedure :
1. Connect the oscilloscope to test points TP (FE) and TP (VC). Procedure :
2. Connect TP (FEI) and GND, and TP (AGCCON) and GND of 1. Connect oscilloscpe to test point TP (TE) on BD board.
the BD board with lead wires. 2. Short-circuit SL502 of the video board to GND.
3. Press the 1/u button to turn the set ON. 3. Turned Power switch on. Press FUNCTION button to select
4. With the disc (YEDS-18) loaded, press the ^ button and CD.
perform focus search. (Focus search will be performed in the 4. Put disc (YEDS-18) in to play the number five track.
same way even while the disc table is pushed in and out.) 5. Press the PLAY MODE/DOLBY NR button. (The tracking
5. Check the symmetry and peak to peak level of the oscilloscope servo and the sledding servo are turned OFF.)
waveform (S curve) at this time. 6. Check the level B of the oscilliscope's waveform and the A (DC
voltage) of the center of the Traverse waveform.
S-curve waveform Confirm the following :
symmetry
A/B x 100 = less than ± 22%
Traverse waveform
Center of the waveform
A
Within 4.0 ± 1.0 Vp-p
B
B
0V A (DC voltage)
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7. level : 1.3 ± 0.6 Vp-p
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform. 7. Press the PLAY MODE/DOLBY NR button. (The tracking
servo and sledding servo are turned ON.) Confirm the C (DC
Adjustment Location: BD board voltage) is almost equal to the A (DC voltage) is step 7.
RF Level Check Traverse waveform
oscilloscope
BD board
C (DC
TP (RF) + 0V voltage)
TP (VC) –
Tracking servo Tracking servo

Procedure : Sled servo Sled servo
1. Connect oscilloscope to test point TP (RF) and TP (VC) on BD OFF ON
board.
2. Connect TP (AGCCON) and GND of the BD board with lead 8. Desolder the short-land (SL502) short-circuited at step 2.
wires.
3. Press the 1/u button to turn the set ON. Adjustment Location: BD board
4. Put disc (YEDS-18) in and playback 5track.
5. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
6. After check, remove the lead wire connected in step 2.
– 16 –
Adjustment Location :
[ BD BOARD ] — SIDE B —
TP
(RF)
TP
(VC)
TP TP
(FE) (TE)
TP
(AGCCON)
TP
(IOP)
VIDEO SECTION
Frequency adjustment
frequency counter
1. Connect the frequency counter to check point of the VIDEO

board. VIDEO board
+
(29 MHz)
2. Adjust CT503 of the VIDEO board so that the frequency counter –
read 27MHz ± 80Hz at STOP condition.
Adjustment Location :
[ VIDEO BOARD ] – SIDE A – [ VIDEO BOARD ] – SIDE B –
D502
SL501 SL502 SL503
TEST MODE (27MHz) IC506
(GND)
IC505
SL503
TEST SL502 IC502
(27MHz) MODE SL501
CT503
VIDEO IC507
FREQUENCY
(GND)
– 17 –
SECTION 8
DIAGRAMS
8-1. CIRCUIT BOARDS LOCATION
VIDEO board
CD SW board
ENCAPSULATED COMPONENT
(EXCEPT THAI)
PANEL board
TUNER unit
(THAI)
TRANS board
SURROUND board
MAIN board
ENCAPSULATED COMPONENT/TUNER
unit is supplied as the assembled block.
MOTOR (TURN) board

CONNECTOR board
BD board
SENSOR board
MOTOR (SLIDE) board
LEAF SW board
AUDIO board
– 18 –
HCD-VX8/VX8J
8-2. BLOCK DIAGRAMS

– CD SECTION –
IC381
OPTICAL PICK-UP BLOCK CD DIGITAL
(D/Q-Np) IC101 MD2 OUT
DIGITAL SERVO 63 D+5V OPTICAL
DETECTOR IC103 DIGITAL SIGNAL PRCESSOR
VCC RF AMP DIGITAL D OUT
E 32K ERROR 64 1 DOUT
OUT
VC RAM CORRECTOR
DATA BUS
A A
5
C C RF RFD RF AC PCM-D
A C 7 RF EQ EFM
D D SUMMING 16 50 REGISTER 66 ADATA
B D 8 AMP AMP DEMODULATOR
BCLK
B B 67 BCLK
6 D/A
RFI 17 INTERFACE LRCK
SUB CODE 65 LRCK
F PROCESSOR C2PO
14 C2PO
MUTE
FOCUS FE 3 MUTE
INTEG- ASYI ASYMMETRY DIGITAL
ERROR 14 49
RATOR CORRECTION PLL
AMP
ASYO
48
E E TRACKING TE
11
F F ERROR 13
10 AMP
LD LD DIGITAL
DRIVE 3 CLV
Q101
LD IC104 (XTAL 33.8MHz)

CLOCK XTAI
VC 71 MCK
LASER 12 GENERATOR 4 2
DIODE BUFFER CONTROL SIGNAL
BLOCK XTSL
PD VC
VC 38
SERVO
BLOCK
SENS
69
7
CTRL1
SENS
A
PD APC LD LD ON
4 22 VIDEO
AMP SECTION
RFDC
LD 43 DETECTOR DATA
POWER
REF
FE SERVO 4 DATA (Page 21)
39 XLAT
TE OP AMP A/D MIRR AUTO 5 XLT
21 41 ANALOG SW CONVERTER DFCT SEQUENCER CLOK
CE FOK CPU 6 CLK
IC102 VC 42 INTERFACE SCOR
INTEG- SE 15 SCOR
FOCUS/TRACKING COIL DRIVE 40 SQSO
SPINDLE/SLED MOTOR DRIVE RATOR 76 SUBQ
SQCK
T+ 77 SQCK
12
TRACKING
COIL TFDR
T 5 PWM S STOP
11 TRDR GENERATOR SERVO DSP 26 A+5V
6 SERVO S101
TFDR
F+ 31 TRACKING INTERFACE LIMIT SW
TRACKING
14 TRDR PWM SCLK
32 GENERATOR SERVO 8 SCLK
FOCUS
FFDR
COIL F 2
13 FRDR FFDR LPH
3 33 FOCUS
FOCUS XRST
FRDR PWM XRST 82
SD+ 34 GENERATOR SERVO
17 LD ON
M102
SLED M SFDR SFDR
SD 24 29 SLED
MOTOR SLED
18 SRDR SRDR PWM
23 30 GENERATOR SERVO
SP+
M101 15 • SIGNAL PATH
SPINDLE M MDP : CD
MOTOR SP 25 25
16 : Digital out
27 VC
: VIDEO
XRST
MUTE 20
TURN
MOTOR DRIVER TABLE
IC701 SENSOR T. SENS
IC702
M701 IN1 8 DISC

8 OUT1
TURN M SENSOR DISC SENS
MOTOR 8 OUT2 IN2 8 IC703 Q701
ROTARY ENC 1
SLIDE
MOTOR DRIVER
IC801
S801
OPEN/CLOSE
ENCODER
S811
ENC 2
ENC 3 C
OPEN MAIN
M801 DET SECTION
8 OUT2 RIN 8 TBL.L
SLIDE M
MOTOR 8 OUT1 FIN 8 TBL.R (Page 25
09 LOAD IN
LOAD OUT
– 19 – – 20 –

HCD-VX8/VX8J
– VIDEO SECTION – D-RAM ROM

IC507 IC506
UCAS
DQ16
LCAS
RAS
DQ1
A11
A17
A10
WE
O0
O7
A0
A8
A0
CE
13 14 28 29 16 - 19 22 - 26 2 - 10 31 - 39 13 - 15 17 - 21 25 4 28 29 3 2 14 10 12 - 5 27 26 23 22
38 42 40 10 - 29 58 - 44 37
MWE
RASO
CAS
MD0
MD15
MA0
MA10
MCE
I
I
LEVEL SHIFT
OUTPUT AMP
IC501
IC401
BUFFER TRAP J302

ADATA 1 4 4 CD-DATA Y-OUT 69 MIX AMP MUTE
Q301 Q302,306,307 5 7 VIDEO OUT
BCLK 13 10 3 CD-BCK Q308,310 Q454
LRCK 5 8 5 CD-LRCK
J301
MUTE S VIDEO
3 1
Q453 4 3 OUT
C2P0 6 CD-C2P0
VIDEO/CD DECODER 2 1
IC505
DATAI
112 HD-OUT
DATAO
119 HD-IN
CLK1 BUFFER
117 HCK C-OUT 75
HRDY Q303,304
113 HRDY
INT
114 HINT
HSEL DA-DATA 110
121 HSEL
RST DA-LRCK 108
60 RESET
DA-BCK 111
INVERTER 93 PGIO2/VSYNC/CSYNC 106 27MHz
VCK-IN
Q502
DA-XCLK 86 DIGITAL FILTER & D/A CONVERTER
IC509
AMP
IC101
18
19
17
D/A
CONV
PLM
14
11 R-CH
3 1 L - CH
XRST C
MAIN
CLK1, DATA0 DATA0 SECTION
9
CLK1 CLOCK 1 (Page 25)
A MECHA. CONTROL
IC502
8
7
MODE
DIVIDER
24
X503
27MHz
CT503
CD VIDEO
10 21 20 4
SECTION
RSTB FREQUENCY
(Page 20)
DATA0
31 DATA1O
DATAI SHARPNESS 34
32 DATA1I
CLK1 DF LATCH 22
33 CLK1
INT LEVEL SHIFT
20 CL680 INT A7 65
HSEL IC504
21 CL680 HSEL
HRDY XIN 15
23 CL680 HRDY X501
RESET 27MHz
24 680 RESET 10MHz 3 6
XOUT 13 S501 NTSC 384FS
11 8
NT/PAL
SYSTEM AUTO 1 12 768FS
45 BUS 93 SELECT
DATA 3 DSP DATA +5V
PAL
XLT 4 DSP LATCH
TEST LED 73 D502
CLK 5 DSP CLK
SENS
SCLK
MUTE
1
2
SENSE
SENSE CLK
10 DSP MUTE
P.ON
XRESET
38
12
–5V/IIC DATA
P. ON/IIC. CLK E
INTERFACE MAIN
CTRL1 11 CTRL1(L:DOUBLE)
IC402 SECTION
27 CTRL2
LDON 28 LDON (Page 26)
SCOR 18 SCOR 14 I2C.DATA
SUBQ 36 SUBQ DATA 13 I2C.CLK RESET 18 D5V
3.3V REG
+3.3V
XIN 19 Q531
SQCK 37 SUBQ CLK DSENS 19 9 I to U X401
77 DEVICE RESET U to I 72 10 U to I 8MHz
• R CH: Same as L ch
XOUT 20
I2C.CLK 29 11 TXD • SIGNAL PATH
I2C.DATA 30 12 RXD
: CD
: CHROMA
XRST
(XTAL 33.8MHz) :Y
09 MCK : VIDEO
– 21 – – 22 –

HCD-VX8/VX8J
– DECK SECTION –
PB A/B
S1004 S1008
A CrO2 B CrO2 MS OUT
RV311 MAIN SECTION

16 17 19 28 27 26
PLAYBACK
IC611 PB-A/B A 120/70 B 120/70
LEVEL MS
DECK A
L 70
A IN PAS
48 PB OUT
HP101 B IN 40 PB L
46 120
PB HEAD R CH DOL LM ON/ 25
(DECK A) R LM ON/OFF
DOLBY NR OFF
DOLBY NR
NORM/
RV301 IC301
HIGH 18 NORM/HIGH
PLAYBACK NR ON/
IC601 NR ON/OFF
LEVEL OFF 23
DECK B
L 24 REC/PB/PASS
RV301
PB
REC/PB HEAD REC LEVEL
(DECK B) RECOUT DOLBY
39 RIN
R R CH TYPE B 44 REC L
EQOUT EQIN BIAS ON/OFF

36 38 BIAS SW 20 BIAS ON/OFF
RM ON/OFF 22 RM ON/OFF
ALC ON/OFF 15 ALC ON/OFF
M
1
C
3
IC602 32 33
P R
4 RELAY
HRPE101 REC/PB CAPM CNT1
CAP MOTOR
RV341 CONTROL CAPM CNT2
REC Q336-343
BIAS +7.5V
Q623
M1 SPEED
SWITCH
CAPSTAN M CONTROL CAP M H / L
Q335
MOTOR
ERASE BIAS
REC BIAS
BIAS OSC
T621, Q621, 622
Q1001
B
ERASE HEAD X MAIN
SECTION
RV1002 RV1001
NORMAL HIGH
REEL (Page 25)
DETECT A SHUT
SPEED SPEED
IC1001
REEL
DETECT B SHUT
IC1002
S1001 (A PLAY)
• R CH : Same as L ch +5V A PLAY
• SIGNAL PATH S1002 (B PLAY)
B PLAY
: PB (DECK A)
: PB (DECK B) S1003 A HALF
(A HALF) +5V
: REC (DECK B)
+5V
S1005
(REC A)
09 S1006 B HALF/REC A/REC B
(B HALF)
S1009
(REC B)
• PLUNGER SOLENOID is supplied MAIN SECTION

as the MECHANICAL BLOCK ASSY.
TRIGGER B TRIG
A DECK/
MOTOR
B DECK
CONTROL
PLUNGER A TRIG
Q331-334
– 23 – – 24 –

HCD-VX8/VX8J
EA
ECHO PROCESSOR
IC711
2 LPF 1 IN LPF 2 OUT 9

– MAIN SECTION – RV712 ECHO
MIC LEVEL
J711 LEVEL
MIX R-CH
MIC
IC712(1/2)
(Page 30) SPE SIG
DISPLAY
SECTION IC181(1/2)
IC712(2/2)
IC181(2/2)
WAKE UP
STANDBY LED
E
MUTE
DJ-SIG IIC DATA DISPLAY
Q181
F DJ-MUTE EQ
IC101(1/2)
VOLUME
IC101(2/2)
IIC CLK
TIMER LED
SECTION
(Page 29)
2 30 RESET
J101
VIDEO/IN EQ Lch
(AUDIO) V AMP 42 41 Lch
68 36 FRONT
L MD IC1201
69 MUTE
TC SELECT SURROUND
MD IN L 66 SWITCH Q113
TU 58 J191
67
65 CD 57 MUTE SUPER
R-CH 72
Q191 WOOFER
MD/VIDEO L-OUT
(AUDIO) MICON 60 11 L-IN 14 38 39 37
OUT L INTERFACE
59 L+R 3
L-R
34 33 32 Q201
1 2 3
DBFB
DBFB
PB L SWITCH
Q111,112
REC L
40 L+R/L-R
RELAY 100 TC RELAY BASS FRQ. 44
A SHUT 91 A SHUT
B SHUT 90 B SHUT DBFB H/L 7
MUTE SW MUTE
B HALF/REC A/REC B 89 B HALF LINE MUTE 6 Q192
Q509
A HALF 88 A HALF
A PLAY 87 A PLAY SW F RELAY 3 F RELAY
B B PLAY
PB A / B
NORM/HIGH
86
84
83
B PLAY SW
PB A/B
EQ H//N
WAKE UP 18
ST-BY LED/CLOCK OUT 39
DECK BIAS ON/OFF 82 BIAS
SECTION RM ON/OFF 81 REC MUTE IIC DATA 30
(Page 24) NR ON/OFF
REC/PB PASS
80 NR ON/OFF
IIC CLK 29
79 R/PB PASS
CAPM CNT1 75 CAPM CNT1 TIMER LED 26
CAPM CNT2 74 CAPM CNT2
RESET 12
ALC ON/OFF 85 ALC
RESET MUTE SW
LM ON/OFF 78 TC MUTE
D
SWITCH Q508
CAP M H/L 76 CAP M H/L Q501
A TRG 73 A TRG
B TRG 72 B TRG AC CUT 22
POWER
MS OUT 77 AMS IN MASTER CONTROL (CHECK)
1 3 SECTION
ST L 38 493-LAT IC501
RDS DATA
2
47 493-DATA
RESET (Page 27)
3 IC502
RDS INT 48 493-CLK
ST-DOUT 1
FM/AM TUNER
TUNER UNIT IS ST-DIN 54 ST DIN
D503
SUPPLED AS THE STEREO 50 STEREO
ASSEMBLED TUNED 51 TUNED
BLOCK +5.6V
ST CE 52 ST CE
X-OUT 13
ST-MUTE 49 ST MUTE X613
ST-CLK 53 ST DOUT 16MHz
X-IN 15
L CH 55 ST CLK
TBL. L 63 TBL L
TBL. R 65 TBL R XC-IN 10
SCOR 19 SCOR X601
32.768KHz
TRAY SENS 61 T SENS XC-OUT 11 • R CH: Same as L ch
HOLD 57 HOLD
SENS 56 SENS
• SIGNAL PATH
X RST 59 XRST RY-SW 36 RY-SW : FM
C CD CLK
CD DATA
37
35
CD CLK
CD DATA
: CD
CD DISC SENS 60 DISC SENS
POWER 2 POWER ON/OFF : PB
SECTION SQ CLK 33 SQ CLK : REC
SQ DATA SQ DATA CD POWER 5 CD POWER
(Page 20) X LAT
32
58 XLT
: VIDEO/MD
OUT-OPEN 71 OUT OPEN FL SW 42 • Abbreviation
STBY RELAY 43
ENC-1 70 ENC1 EA : Saudi Arabia model.
ENC-2 69 ENC2/DISC-LED
ENC-3 68 ENC3/UP-SW
LD IN 67 LOAD IN STK MUTE 1 STK MUTE
LD OUT 66 LOAD OUT
21 RDS DATA PROTECTOR 27 PROTECTOR

09
20 RDS INT
– 25 – – 26 –

HCD-VX8/VX8J
– POWER SECTION –
TM402
F RELAY SURROUND
SPEAKER
• R CH : Same as L ch
• SIGNAL PATH
THERMAL
DET
: FM
POWER AMP Q831, 832 • Abbreviation
IC801 THP831
EA : Saudi Arabia model.
RY401 FAN MOTOR M901
FRONT
Lch
18 14
Lch
DRIVER M FAN SP : Singapore model.
UNREG
16 RELAY
Q401, 402
–7V
MOTOR MY : Malaysia model.
VH+ DRIVE Rch HK : Hong Kong model.
Q435, 436, 431
TW : Taiwan model.
VH+ SUPP
VH+ Q803, 881 IA : Indonesia model.
OVER LOAD FRONT TM401
SWITCH
DET
Q437 FRONT
Q801
MUTE SPEAKER
SWITCH
Q804 Rch
Rch
J701
PHONES
DBFB
PROTECT
MUTE
CONTROL SWITCH
Rch Q432 - 434 Q439
MUTE Rch
STK MUTE SWITCH
Q412, 411
RY-SW
D PROTECTOR
MAIN
SECTION T951
POWER TRANSFORMER
(Page 26) JW51
RECTIFIER +VH
D+5V UNSW RECT
D507 AC1
–VH D831
RECTIFIER AC2
+5.6V (STBY) RDS D+5V UN SW +VL RECT
D922
D832 AC2
–VL
RECTIFIER AC1
+5V (STBY) +5V (LED)
D924
(DISPLAY) D509 (DISPLAY)
D+5VSW +5V OUT IC902

3 1
Q905,D923 REG
SWITCH
Q904 +7V REG
A+7V Q901,902,913
SWITCH
POWER ON/OFF
Q923, 903 E,EA,MY,SP,HK,TW,IA
AC3
CD D+5V (SW) +5V REG RECTIFIER VOLTAGE
RECT
Q907 D925 D901-904 SELECTOR
CD A+5V (SW) A–7V –7V REG AC3
Q951,952,914 S951
+5V OUT
3 IC904 1
Q911 REG AC4
RECT
SWITCH SWITCH CD MOTOR +7V 3 IC901 1
+7V REG D907-910 AC4
Q908 Q912
TC MOTOR +12V AC
CD POWER IN
VF
+10V REG
ST+10V 3 IC903 1
Q909 +12V REG
VF
09
– 27 – – 28 –

HCD-VX8/VX8J
– DISPLAY SECTION – D637 RIGHT
LED SWITCH +5V (LED)

Q607
15 LED SWITCH
GRADATION L
Q608
D638 LEFT
IC604
1
|
5
•
7 Q601,602
L/P SCK 3 13 |
4 LED
LED LA 11 PANEL LED +5V (LED)
SWITCH •
L/P DAT 5 15
17
IIC DATA 78 I2C DATA •
19
IIC CLK 79 I2C CLK |
23
LED
L SEL 7 CONTROL
Q603
SIRCS 1 REMOTE
DISPLAY CONTROL 16 CONTROL
S LOW (F01)
RESET 73 RESET IC601 RECEIVER
BPF1 (F02) 17
IC602
BPF2 18
BPF3 19
BPF4 20 S601
ALL B (L+R) 21 (JOG)
JOG A 2 ROTARY
JOG B 8 ENCODER
KEY 0 11
KEY
72 XOUT
X601 MATRIX
KEY 3 14
12.5MHz
70 XIN MUTE
Busy for PAD 75 SWITCH DJ MUTE
Q851
WAKE UP 22 GRADATION R/WAKE UP PAD LA 6 SOUND MIX

IC605
CH for PAD 74
15 SD
F
VOL A 9 ROTARY 14 SI MAIN
VOL B 10 ENCODER 8 ST SECTION
E SEG1-SEG22
46 - 67
GR2-GR12
33 - 40, 42 - 44
GR1, GR13-GR18
27 - 32, 45
S602
VOLUME
16 CH
A.OUT 23 DJ SIG
(Page 25)
MAIN 20 BUSY
SECTION XT XT
IND BUFF 2 3
(Page 26) Q610-616
X602
FL601 4.09MHz
VF VF
FLUORESCENT INDICATOR TUBE
SPEANA BPF FILTER

IC603
S LOW
F01 17
BPF1
F02 16
SPE SIG 4 LINE IN BPF2
F04 14
BPF3
F05 13
6 REC IN BPF4
F06 12
ALLB
L+R 11
STANDBY LED
D804
ECO
LED SWITCH
TIMER LED +5V (LED)
Q605
D635
TIMER SELECT
09
– 29 – – 30 –

HCD-VX8/VX8J
WAVEFORMS – VIDEO SECTION – – MAIN (3/4) SECTION –

THIS NOTE IS COMMON FOR PRINTED WIRING
– CD SECTION –
BOARDS AND SCHEMATIC DIAGRAMS. 1
1 7
(In addition to this, the necessary note is printed
1
in each block.) 4Vp-p 5.2Vp-p
5.8Vp-p
1.3Vp-p
For schematic diagrams.
10MHz 27MHz 32.768kHz
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF IC502 !£ XOUT IC509 1 XT1 IC501 !¡ XC-OUT
50 WV or less are not indicated except for electrolytics IC101 %º RFAC
2 8 2
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise 2
4.6Vp-p 5.5Vp-p
specified. 2.5V
1Vp-p
• ¢ : internal component.
• 2 : nonflammable resistor. H 44.1kHz 16MHz
• 1 : fusible resistor. APPROX 500mVp-p
IC505 &∞ COUT IC509 !ª LRCK IC501 !£ X-OUT
• C : panel designation. IC101 $¡ TE
3 9
Note: The components identified by mark ! or dotted line 3
with mark ! are critical for safety. 2Vp-p 4.8Vp-p – PANEL (2/3) SECTION –
Replace only with part number specified. 2.5V
• U : B+ Line. H 2.11MHz 1
APPROX 200mVp-p
• V : B– Line. IC505 ^ª YOUT IC509 !¶ BCLK
3.4Vp-p
• H : adjustment for repair. IC101 #ª FE
• Voltages and waveforms are dc with respect to ground 4 0
under no-signal (detuned) conditions. 4 12.5MHz
• Voltages are taken with a VOM (Input impedance 10 MΩ). 1Vp-p 4.8Vp-p IC601 &™ X OUT
2.6Vp-p
Voltage variations may be noted due to normal produc-
tion tolerances. 33.8MHz
2
H
• Waveforms are taken with a oscilloscope. 7.5µsec IC401 7 COUT IC504 8 384FS
Voltage variations may be noted due to normal produc-
IC101 @∞ MDP 3.6Vp-p
tion tolerances. 5 !¡
• Circled numbers refer to waveforms.
4.09MHz
• Signal path. 2Vp-p
F : FM
3.8Vp-p IC605 2 XT
g : VIDEO/MD
E : PB (DECK A) H 27MHz
d : PB (DECK B) IC401 1 YOUT IC504 6 27M
G : REC (DECK B)
m : CHROMA 6 !™
n :Y 1.2
o : VIDEO Vp-p 2.8Vp-p
J : CD
c : digital out H 33.8MHz
• Abbreviation J302 VOUT IC504 !™
EA : Saudi Arabia model.
SP : Singapore model.
MY : Malaysia model.
HK : Hong Kong model.
TW : Taiwan model.
IA : Indonesian model.
TH : Thai model.
For printed wiring boards.

Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
• p : parts mounted on the conductor side.
• ® : Through hole.
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
• Indication of transistor
C
Q These are omitted
BC E
B E
These are omitted
– 31 – – 32 –

HCD-VX8/VX8J
8-3. PRINTED WIRING BOARD – CD SECTION –

• See page 18 for Circuit Boards Location.
(Page 42)
– 33 – – 34 –

HCD-VX8/VX8J
8-4. SCHEMATIC DIAGRAM – CD SECTION –

• See page 31 for Waveforms.
• See page 77 for IC Block Diagrams.
• See page 80 for IC Pin Functions.
(Page 43)
– 35 – – 36 –

HCD-VX8/VX8J
8-5. SCHEMATIC DIAGRAM – DECK SECTION –
(Page 55)
– 37 – – 38 –

HCD-VX8/VX8J
8-6. PRINTED WIRING BOARD – DECK SECTION –

1 2 3 4 5 6 7 8 9 10 11 12
(Page 49)
– 39 – – 40 –

HCD-VX8/VX8J
8-7. PRINTED WIRING BOARD – VIDEO SECTION –

• See page 18 for Circuit Boards Location. (Page 50)
(Page 34)
• Semiconductor • Semiconductor
Location Location
Ref. No. Location Ref. No. Location
D301 E-1 IC501 C-2
D501 D-3 IC502 B-1
D502 A-3 IC506 C-3
IC101 A-1 Q302 E-3

IC401 E-3 Q303 D-1
IC504 A-1 Q453 E-2
IC505 C-2 Q454 E-2
IC507 C-1 Q531 D-1
IC509 B-1
Q301 E-1
Q304 D-3
Q306 E-1
Q307 E-2
Q308 E-2
Q310 E-2
Q502 D-3
– 41 – – 42 –

HCD-VX8/VX8J
8-8. SCHEMATIC DIAGRAM – VIDEO (1/3) SECTION –

(Page
47)
(Page 35)
(Page 51)
(Page 45) (Page 45) (Page 47)
– 43 – – 44 –

HCD-VX8/VX8J

(Page 43) (Page 43)
(Page 47)
(Page 47)
– 45 – – 46 –

HCD-VX8/VX8J

(Page 44)
(Page 44)
(Page 46)
(Page 46)
– 47 – – 48 –

HCD-VX8/VX8J
8-11. PRINTED WIRING BOARD – MAIN SECTION –


• Semiconductor Location
Ref. No. Location Ref. No. Location
D141 E-10 Q113 E-9
D191 E-10 Q161 C-9
D331 E-1 Q162 C-9
D334 E-1 Q163 E-9
D335 F-1 Q181 E-11
D401 G-11 Q191 E-10
D403 F-12 Q192 E-10
D405 H-6 Q201 D-9
D406 I-4 Q251 C-9
D407 I-2 Q331 C-1
(Page
D411 G-3 Q332 C-2 39)
D501 D-7 Q333 C-2
D502 E-6 Q334 C-2
D503 D-6 Q335 D-1
D504 D-7 Q336 F-1
D505 D-7 Q337 F-1
D506 D-7 Q338 F-1
D507 E-6 Q339 F-1
D509 F-2 Q340 E-1
D607 E-5 Q341 E-1
D644 C-8 Q342 E-1
D801 J-11 Q343 E-1 (Page 59)
D802 G-9 Q401 F-12
D803 G-11 Q402 E-12
D831 I-6 Q411 G-2
D832 J-7 Q412 G-2
D851 J-10 Q431 G-12
(Page 61)
D852 G-9 Q432 G-11 (Page 76)
D881 H-9 Q433 F-11
D901 J-4 Q434 F-11
D902 I-4 Q435 F-11
D903 J-4 Q436 F-11
D904 I-4 Q437 G-12
D905 I-1 Q439 F-12
D906 H-1 Q471 F-12
D907 J-5 Q501 D-7
D908 I-5 Q508 D-7
D909 J-5 Q509 E-7
(Page
D910 J-5 Q801 H-10 75)
D915 I-4 Q803 G-10
D921 H-4 Q804 G-9
D922 G-4 Q831 G-10
D923 G-4 Q832 G-10
D924 F-2 Q851 J-11
D925 G4 Q881 I-9
Q901 H-2
IC101 B-10 Q902 I-1
IC181 D-11 Q903 H-1
IC301 B-3 Q904 G-4
IC381 A-12 Q905 G-4
IC501 D-5 Q907 G-5
IC502 D-7 Q908 G-4
IC801 G-10 Q909 I-4
IC901 G-6 Q911 G-3
IC902 G-4 Q913 H-1
IC903 I-4 Q914 G-2
IC904 H-3 Q923 H-1
Q951 G-2
Q111 D-10 Q952 H-1
Q112 D-10
(Page 75)
– 49 – – 50 –

HCD-VX8/VX8J
8-12. SCHEMATIC DIAGRAM – MAIN (1/4) SECTION –
(Page
53)
(Page 43)
(Page
53)
(Page 70)
(Page 70)

(Page 76)
– 51 – – 52 –

HCD-VX8/VX8J

• See page 49 for Printed Wiring Board.
(Page
52)
(Page
56)
(Page
52)
(Page
(Page
73)
56)
(Page 57) (Page 57) (Page 58) (Page 58)
– 53 – – 54 –

HCD-VX8/VX8J


(Page
53)
(Page
57)
(Page
57)
(Page
57)
(Page
57)
(Page 38)
(Page 59)
– 55 – – 56 –

HCD-VX8/VX8J

(Page 53)
(Page 52) (Page 53) (Page 53, 54) (Page 54)
(Page
56)
(Page
56)
(Page
56)
(Page
56)
(Page 73)
(Page 66)
– 57 – – 58 –

HCD-VX8/VX8J
8-16. PRINTED WIRING BOARD – LEAF SW SECTION –
(Page 49)
8-17. SCHEMATIC DIAGRAM – LEAF SW SECTION –
(Page 55)
– 59 – – 60 –

HCD-VX8/VX8J
8-18. PRINTED WIRING BOARD – PANEL SECTION –

• Semiconductor
Location
Ref. No. Location
D601 F-6
VIDEO CD
D608 C-9
D609 C-2
D611 C-6
D612 C-7
(Page 49)
D613 C-5 PBC
D614 C-4
D615 E-4
D616 A-2
D617 B-2
D618 B-2 PBC OFF
D619 D-3
D620 E-1
D621 G-7
D622 G-4
D623 G-7
D624 E-5
D625 E-4
D626 E-7
D627 G-9
D628 G-8
D629 F-9
D630 F-8
D631 D-6
D632 D-5
D633 D-8
D634 D-7
D635 A-9
D701 E-9
NEXT
IC601 B-5
IC602 C-9 PREY RETURN SELECT
IC603 B-7
IC604 F-5
REC
IC605 C-4 PAUSE/START
IC711 E-8 JOG
IC712 G-8
Q601 F-6
Q602 F-6
Q603 F-6
Q604 A-10
Q605 A-10
Q607 B-2
Q608 C-9
Q610 B-7
Q611 B-7
Q612 B-7
Q613 B-7
Q614 B-7
Q615 B-8
Q616 B-8
Q620 A-10
– 61 – – 62 –

HCD-VX8/VX8J
8-19. SCHEMATIC DIAGRAM – PANEL (1/3) SECTION –

– 63 – – 64 –

HCD-VX8/VX8J

(Page (Page 57)

63, 64)
(Page 67) (Page 68)
– 65 – – 66 –

HCD-VX8/VX8J

(Page 65) (Page 66)
(Page 63)
(Page 63)
– 67 – – 68 –

HCD-VX8/VX8J
8-22. SCHEMATIC DIAGRAM – CD MOTOR SECTION –
1SS119
(Page 51)
MTZJ-T-72-5.6C (M) 1SS119
(Page 51)
MTZJ-T-72-3.6C (M)
– 69 – – 70 –

HCD-VX8/VX8J
8-23. PRINTED WIRING BOARD – CD MOTOR SECTION –

(Page 49)
(Page 50)
– 71 – – 72 –

HCD-VX8/VX8J
8-24. SCHEMATIC DIAGRAM – TRANS SECTION –
(Page 54)
(Page 57)
– 73 – – 74 –

HCD-VX8/VX8J
8-25. PRINTED WIRING BOARD – TRANS SECTION –

• See page 18 for Circuit Boards Location. 8-26. SCHEMATIC DIAGRAM – SURROUND SECTION –
(Page 51)
8-27. PRINTED WIRING BOARD – SURROND SECTION –

(Page 50)
(Page 49) (Page 50)
– 75 – – 76 –

HCD-VX8/VX8J
8-28. IC BLOCK DIAGRAMS • BD Board • VIDEO (3/3) Board
• BD Board IC103 CXA2568M-T6 IC509 PCM1727E-2/T2
384fs
IC101 CXD3008Q APC PD AMP VCC 24 VCC
DVSS2
PCMD
EMPH
SQSO
SQCK
SOCK
SOUT
23 LC/PD
SCSY
EXCK
EXCK
XOLT
XTA0
XTA1
XTSL
VCC XT1 1 CLOCK MANAGER 24 XT2

BCK
22 LD_ON •
VEE DUAL PLL
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 HOLD 1
VEE
AGCVTH 2 VREF
VDD 1 65 LRCK PGND 2 23 DGND
APC LD AMP POWER
XRST 2 LD 3 21 HOLD_SW VCP 3 SUPPLY 22 VDD
DIGITAL 64 DOUT
MUTE 3 OUT 63 MD2 VC 20 AGCCONT 21 SCKO1
VCC (50%/30%
20 SCKO2
DATA 4 OFF) NCKO 4
D/A 62 ASYE PD 4
XLAT 5 19 RF_BOT RSV 5 19 LRCK
CPU INTERFACE
CLOK 6 61 SCKO3 6 AUDIO
INTERFACE DATA INPUT
SENS 7 18 DATA
60 VPC0 VC INTERFACE
CLOCK A 5 ML 7
ERROR GENERATOR 59 V16M 17 BCK
MC 8 MODE
SCLK 8 CORRECTOR 58
MC 9 CONTROL
ATSK 9 B 6 VEE
57 BIAS 18 RFTC RSTB 10
WFCK 10 EFM RF SUMMING AMP RF_EQ_AMP
SERVO 17 RF_1 16 ZERO
XUGF 11 DEMODURATOR 56 DVDD2 C VC VC OPEN
AUTO 7 16 RFO 8 TIME OVER
XPCK 12 SEQUENCER SAMPLING DIGITAL
32K
GFS 13 55 PCO 15 RFE FILTER
RAM D 15 CAP
54 FIL1 8 •
C2P0 14 DIGITAL ERROR AMP
PLL 53 FIL0 VC FUNCTION
SCOR 15 FOCUS
VEE 9 VEE CONTROL
SERVO 52 CLTV 14 FE 14 VOUTL
INTERFACE SUB
CODE VC
PROCESSOR 51 AVSS1 MULTI LEVEL MULTI LEVEL
VC BPZ
C4M 16 F 10 CONTROL ∆Σ ∆Σ
WDCK 17 ASYMMETY 50 RFAC MODULATOR MODULATOR
CORRECTOR
49 ASY1
DVSS 18 E 11
MIRR 48 ASY0
DFCT 5 LEVEL 5 LEVEL
FOK 47 AVDD DAC DAC
13 TE
VC
46 1GEN
PWM GENERATOR SERVO DSP TRACKING CR LPF CR LPF
45 AVSS0 VC
COUT 19 FOCUS PWM OP VC BUFFER ERROR AMP • •
FOCUS SERVO VCC VOUTR 11
GENERATOR A/D AMP 44 AD10 VC 12 VC OUTPUT OUTPUT
MIRR 20 CONVERTER ANALOG AMP AMP
TRACKING PWM TRACKING 43 RFDC VEE
DFCT 21 GENERATOR SERVO SW 42 CE
FDK 22 SLED PWM VC AGND 12 13 VCA
SLED SERVO 41 TE
PWM1 23 GENERATOR
LOCK 24 DIGITAL
PLL
MDP 25 • PANEL (3/3) Board
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 IC604 NJU3716M-T2
SSTP
FST0
DVDD1
SFDR
SRDR
TFDR
TRDR
FFDR
FRDR
DVSS1
TES1
TES1
VC
FE
SE
• PANEL (2/3) Board 12 SO

DATA 13 11 P16
• PANEL (1/3) Board IC605 MSM6654A-540GS-K 10 P15
CLK 14 9 P14
IC603 BA3830F IC711 M65850FP-E1 8 P13
A2 15
LPF2OUT
7 P12
OP2OUT
LPF2IN
CLOCK
A1 14
OP2IN
6 GND
VCC
REF
R02 1 REFFERENCE A0 13 ADDRESS 1M BIT ROM

RESET 18 RESET 7 17 STAGE EDITING ROM & 5 P11
CURRENT & (MSM6654A)
SW3 12 SWITCHING ADDRESS ROM
14 13 12 11 10 9 8 MULTIPLEXER
SW2 11 CONTROLLER CONTAINS 22KBIT 8 4 P10
SHIFT REGISTER
REFFERENCE SW1 10
P01 2 17 f01 OSCILLATOR 3 P9
LATCH
CURRENT D/A LPF2 SW0 9
16 TEST 2 P8
1/2 VCC
ADPCM 17 RESET
LINE 3 BPF DET 16 f02 DATA SYNTHESIZER
CLOCK DO1 CONTROLLER 1 P7
NF MO 18 NC
AUTO MAIN 20KBIT
RESET RANDOM 19 NC
BPF DET RESET CONTROL SRAM RND 8
MI CIRCUIT PCM 20 BUSY
LINE D1 DO0 NC 7 SYNTHESIZER
4 15 f03 21 NC
IN NC
BPF DET 6 17 STAGE 22 XT/CR
A/D OSC3 5 (MSM6654A) 12
ADDRESS 23 AOUT
LPF1 NC 4 I/O
REC 5 BPF DET 14 f04 COUNTTER 24 GND
INTERFACE
NF MELODY 12 BIT
1 2 3 4 5 6 7 GENERATOR DAC
BPF DET
LPF1IN
LPF1OUT
OP1OUT
OP1IN
CC1
CC2
GND
REC 6 13 f05 OSC

IN OSC2 3 TIMING
(XT/CR) CONTROLLER BEEP TONE
BPF DET OSC1 2 GENERATOR LPF
VDD 1
RESET 7 12 f06 STB 15
DET CONTROL
C CLR 16
BIAS 8 11 REC
C Bias LEVEL
GND1 9 10 VCC 17 18 19 20 21 22 23 24
P1
GND
P2
P3
P4
P5
P6
VDD
– 77 – – 78 –

• SURROUND Board
IC1201 LV1150
B 50k
R-OUT 13
12 R-IN
A VIRTUAL
50k
R +DELAY 2k
11 L-IN
B
L-OUT 14
10 RS-OUT
A
L.P.F
EF-VOL 15 9 L-FS-IN
L –DELAY
VREF 16 8 VCC
AGND 17 7 R-PS-IN
L +R
L –R
DC-OUT 18 6 LS-OUT
D/A 19 5 LPF2
SRAM
NS 20 B A 4 LPF1
ADM
A/D 21 3 SW2
ADM-CONT
2 SW1
1 VSS
VDD 22 VDD
LC-INB 23
OSC
LC-INE 24
– 79 –
8-29. IC PIN FUNCTIONS
• IC101 DIGITAL SIGNAL PROCESSOR (CXD3008Q) (BD Board)
Pin No. Pin Name I/O Function

1 DVDD0 — Digital power supply
2 XRST I System reset
3 MUTE I Muting selection pin
4 DATA I Serial data input, supplied from CPU
5 XLAT I Latch input, supplied from CPU
6 CLOK I Serial data transfer clock input, supplied from CPU
7 SENS O SENS output
8 SCLK I SENS serial data read-out clock
9 ATSK I/O Input pin for anti-shock (Ground)
10 WFCK O WFCK (Write Frame Clock) output (Not used)
11 XUGF O XUGF output (Not used)
12 XPCK O XPCK output (Not used)
13 GFS O GFS output (Not used)
14 C2P0 O C2PO output
15 SCOR O Sub-code sync output
16 CM4 O 4.2336MHz output (Not used)
17 WDCK O 48-bit slot D/A interface word clock (Not used)
18 DVSS — Digital ground
19 COUT O Numbers of track counted signal output (Not used)
20 MIRR O Mirror signal output (Not used)
21 DFCT O Defect signal output (Not used)
22 FOK O Focus OK output (Not used)
23 PWM1 I (Not used)
24 LOCK I/O GFS in sampled by 460Hz (Not used)
25 MDP O Output to control spindle motor servo
26 SSTP I Input signal to detect disc inner most trak
27 FST0 O 2/3 divider output (Not used)
29 SFDR O
Sled drive output
30 SRDR O
31 TFDR O
Tracking drive output
32 TRDR O
33 FFDR O
Focus drive output
34 FRDR O
35 DVSS1 — Digital ground
36 TEST I
TEST pin connected normally ground
37 TES1 I
38 VC I Center voltage input
39 FE I FOCUS error signal input
40 SE I Sled error signal input
– 80 –
41 TE I Tracking error signal input
42 CE I Center servo analog input
43 RFDC I RF signal input
44 ADI0 O Test pin (Not used)
45 AVSS0 — Analog ground
46 IGEN I Power supply pin operational amplifiers
47 AVDD — Analog power supply
48 ASYO O EFM full swing output
49 ASYI I Asymmetry comparate voltage input
50 RFAC I EFM signal input
51 AVSS1 — Analog ground
52 CLTV I Control voltage input for master VCO
53 FILO O Filter output for master PLL
54 FILI I Filter input for master PLL
55 PCO O Charge-pump output for master PLL
56 AVDD1 — Analog power supply
57 BIAS I Asymmetry circuit constant current input
58 VCTL I Control voltage input for variable pitch PLL
59 V16M I/O 16.9344MHz output (Not used)
60 VPCO O Charge-pump output for variable pitch PLL (Not used)
62 ASYE I Asymmetry circuit ON/OFF
63 MD2 I Digital-out ON/OFF control
64 DOUT O Digital-out output
65 LRCK O 48-bit slot D/A interface, LR clock output
66 PCMD O 48-bit slot D/A interface, Serial deta output
67 BCLK O 48-bit slot D/A interface, bit clock output
68 EMPH O Playback disc output in emphasis mode (Not used)
69 XTSL I X’tal selection input pin
70 DVSS2 — Digital ground
71 XTAI I X’tal oscillator circuit input
72 XTAO O X’tal oscillator circuit output (Not used)
73 SOUT O
74 SOCK O (Not used)
75 XOCT O
76 SQSO O Sub-Q serial output
77 SQCK I Clock input for SQSO read-out
78 SCSY I Sub-code input
79 SBSO O Sub-P through Sub-W serial output (Not used)
80 EXCR I Clock input for SBSO read-out
– 81 –
• IC502 MPEG DECODER, MECHANISM CONTROL (M30620MC-A05FP) (VIDEO (1/3) Board)

1 SENSE I Internal state (SENSE) monitor input (IC101)
2 SENSE CLK O Serial data reading clock output (IC101)
3 DSP DATA O Serial data output (IC101)
4 DSP LATCH O Lach output (IC101)
5 DSP CLK O Serial data clock output (IC101)
6 TSENS I Not used
7 REMOTE IN I Not used
8 BYTE I External bus width change input (Connected to ground)
9 VSS – Ground
10 DSP MUTE O Mute output (IC101) “H” : mute
11 CTRL1 (L : DOUBLE) O Double change output (IC101) “L” : double
12 XRESET I System reset input “L” : reset
13 XOUT O Main clock output (10MHz)
14 VSS – Ground
15 XIN I Main clock input (10MHz)
16 VCC – +5V power supply
17 NMI I Requests mask disable interruption input (Connected to +5V)
18 SCOR I Subcode sync input (IC101)
19 D SENS I Not used
20 CL680 INT I Video CD interruption input (IC505)
21 CL680 HSEL O Video CD select data of the host MPU (IC505)
22 DF LATCH O Digital filter latch output (IC509)
23 CL680 HRDY I Ready signal input for communication to the host MPU (IC505)
24 680 RESET O Video CD reset output (IC505) “L” : reset
25 JOG1 I Not used
26 JOG2 I Not used
27 CTRL2 O Double control output (IC101) “H” : double
28 LD ON O Laser diode ON/OFF output
29 IIC1 I/O IIC convertion microcomputer receive data (Former type), IIC clock input from master control (New type)
30 IIC0 I/O IIC convertion microcomputer transmittion data (Former type), IIC data input from master control (New type)
31 DATA1O O Serial 1 data output (IC505, 509)
32 DATA1I I Serial 1 data input (IC505, 509)
33 CLK1 O Serial 1 clock output
34 SHARPNESS O Sharpness output L : normal, H : sharpness
35 XVLEVEL. DOWN O Fix the video signal output level output
36 SUBQ DATA I Serial 2 data input for subcode sync reading
37 SUBQ CLK I Serial 2 clock input for subcode sync reading
38 P. ON I Not used
39 BUS XRDY I Not used
40 BUS I Not used
41 BUS XHOLD I Not used
42, 43 BUS I Not used
44 BUS XRD I Model selection input “L” : chinese model, “H” : except chinese model
45 BUS I V sync signal input
– 82 –
46 BUS XWRL I Not used
47 LO. BOOST I Not used
48 AUDIO MUTE O Audio mute output “L” : mute
49 LOAD OUT I Not used
50 LOAD IN I Not used
51 INSW I Not used
52 OUTSW I Not used
53 MODEL 1 I L : System input (Fixed at “L”)
54 MODEL 2 I L : System input (Fixed at “L”)
55 TBLL I Not used
56 TBLR I Not used
57 ENC 1 I Not used
58 ENC 2 I Not used
59 ENC 3 I Not used
60 — I Not used
61 — I Not used
62 VCC – +5V power supply
63 — I Not used
64 VSS – Ground
65 A7 O Video mute output “L”
66 to 71 A6 to A1 I Not used
72 U to I I IIC convertion microcomputor transmittion input
73 TEST LED O TEST LED for MPEG decoder
74 TEST 1 I Test mode for Video CD check
75 TEST 2 I Test mode for servo check
76 TEST 3 I Not used
77 DEVICE RESET O Device system rest output “L” : reset
78 STANDBY I Not used
79 FL CS I Not used
80 FL I Not used
81 to 88 D7 to D0 I Not used
89 MIC CTRL I Not used
90 KEY 1 I Not used
91 KEY 2 I Not used
92 KEY 3 I Not used
93 NY/PAL I NTSC/PAL select switch input
94 MUSIC VOL I Not used
95 KEY 4 I Not used
96 AVSS – A/D converter ground
97 MODE. SW I Not used
98 VREF I A/D converter reference voltage input (Connected to +5V)
99 AVCC – A/D converter +5V power supply
100 AMP. ON I Not used
– 83 –
• IC505 CD DECODER, SYSTEM CONTROL (CL680T-D1) (VIDEO (2/3) Board)

1 NC – Not used
2 VSS – Ground
3 CD-BCK I CD Decode bit clock
4 CD-DATA I CD Decode data
5 CD-LRCK I CD Decode Left or Right channel selection clock
6 CD-C2PO I CD Decode C2 error data
7 NC – Not used
8 NC – Not used
9 NC – Not used
10 MD0 I/O Data bus between Microcode ROM/DRAM and CL680
16 VSS – Ground
18 VDD3 – +3.3V Power supply
20 VSS – Ground
30 NC – Not used
31 NC – Not used
32 NC – Not used
33 NC – Not used
34 NC – Not used
35 NC – Not used
36 NC – Not used
37 MCE O Chip enable signal to Microcode ROM
38 MWE O Write enable signal to DRAM
39 VSS – Ground
40 CAS O Column address strove : Latch the column address to DRAM
41 VDD3 – +3.3V power supply
42 RAS0 O Row address strove : Latch row address to DRAM
43 RAS1 – Not used
44 MA10 O Address data from CL680 to Microcode ROM
45 MA9 O Address data from CL680 to Microcode ROM
– 84 –
46 MA8 O Address data from CL680 to Microcode ROM/DRAM
47 VSS – Ground
53 VSS – Ground
59 PGIO7 I/O Not used
60 RESET I Reset signal input from the host MPU
61 VDDMAX-IN I Fix the maxium input voltage each input pin and I/O pin
62 NC – Not used
63 NC – Not used
64 NC – Not used
65 AGND DAC – Ground
66 AVDD DAC – +3.3V Power supply
67 COMPOS OUT O Not used
69 Y-OUT O Luminance signal out
72 RREF I Fix the video signal output level
73 (1.235V) VREF O Reference voltage (+1.235V)
75 C-OUT O Chrominance signal out
77 (GCK INT) CLK SEL I GCK selection “H”; Internal, “L”; External
78 CLK SEL I DA-XCK selection (1)
79 CLK SEL I DA-XCK selection (2)
80 VSS – Ground
81 RESERVED I Selection the operation clock 42.336MHz
83 DA-EMP – Not used
84 RESERVED – Not used
85 AGND PLL – Ground
86 DA-XCLK I Main reference clock input (16.9344MHz=384fs)
87 AVDD PLL – +3.3V
– 85 –
93 PGIO2/VSYNC/CSYNC O Vertical synchronized signal of video signal
94 AVDD PLL – +3.3V Power supply
95 NC – Not used
96 NC – Not used
97 NC – Not used
98 AGND PLL – Ground
99 VSS – Ground
100 NC – Not used
101 PGIO3/HSYNC I/O Not used
103 PGIO1/VCK-OUT I/O Not used
104 VSS – Ground
105 GCK I Not used
106 VCK-IN I Main clock for video signal processer
107 GCKOUT/DA-EMP O Not used
108 DA-LRCK O Digital Audio Left or Right channel selection clock
109 VDDMAX-OUT O Fix the maxium output voltage certain output pins (Connected to +5V)
110 DA-DATA O Digital Audio data
111 DA-BCK O Digital Audio bit clock
112 HD-OUT O Serial Data output from CL680 to the host MPU
113 HRDY O Ready signal CL680 is ready for communication to the host MPU
114 HINT O Request signal for interrupting the host MPU
115 CDG-SCK I/O Not used
116 VSS – Ground
117 HCK I Host clock : referance signal for the host bus interface
119 HD-IN I Serial Data output ftom the host MPU to CL680
121 HSEL I Select data or address of the host MPU
122 CDG-SDATA I Ground (Not used)
123 CDG-VFSY I Ground (Not used)
124 CDG-SOS1 I Ground (Not used)
125 NC – Not used
126 NC – Not used
127 NC – Not used
128 NC – Not used
– 86 –
• IC501 MASTER CONTROL (M30622MA-A09FP) (MAIN Board)
1 STK-MUTE O Power amp ON/OFF signal output
2 POWER O Power ON/OFF signal output
3 F-RELAY O Front speaker relay control output
4 REAR-RELAY O Rear speaker relay control output (Not used)
5 CD-POWER O CD power on signal output
6 LINE-MUTE O Line mute ON/OFF selection output
7 DBFB-H/L O DBFB H/L select signal output
8, 9 – – Not used
10 XC-IN I
X’tal (32.768MHz)
11 XC-OUT O
12 RESET I Reset signal input
13 X-OUT O X’tal (16MHz)
14 VSS – Ground
15 X-IN I X’tal (16MHz)
16 VCC – Power supply (+5V)
17 NMI I Not used (PULL UP EVER+5V)
18 WAKE UP I WAKE UP (Fixed at fixed at “L”)
19 SCOR I Subcode data request signal output (Not used)
20 RDS-INT I
RDS data interrupt input
21 RDS-DATA I
22 AC-CUT I Back up signal input
23 PL-CLK O Clock signal to pro-logic (Not used)
24 PL-DATA O Data signal to pro-logic (Not used)
25 PL-LAT O Latch signal to pro-logic (Not used)
26 TIMER LED I Timer LED ON/OF
27 PROTECTOR I Speaker protect ON/OF
28 – – Not used
29 IIC-CLK O Clock output for IC601
30 IIC-DATA O Data output for IC601
31 – – Not used
32 SQ-DATA I Subcode Q data clock input
33 SQ-CLK I Not used
34 SW-MODE O Not used
35 CD-DATA O CD data output (Not used)
36 RY-SW I Head phone swich detect
37 CD-CLK O CD clock output (Not used)
38 493-LAT O Latch signal output for M62493FP (IC101)
ST-BY LED/
39 O Clock ond stand by LED signal output
CLOCK-OUT
40 L+R/L-R I
Not used
41 BY-PASS I
42 FL-SW I FL switch ON/OFF
43 STBY RELAY I Stand by relay ON/OFF
44 BASS FREQ O FREQ high/low signal for SYNC bass
45, 46 – – Not used
47 493-DATA O Data output for M62493FP (IC101)
48 493-CLK O Clock output for M62493FP (IC101)
49 ST-MUTE O Tuned mute signal output
– 87 –
50 STEREO I Stereo detection for tuner
51 TUNED I Tuned detection for tuner
52 ST-CE O Tuner chip enable output
53 ST-DOUT O Tuner data output
54 ST-DIN I Tuner data input
55 ST-CLK O Tuned clock output
56 SENS I BD Condition signal input (Not used)
57 HDLD O Mode hold signal output (Not used)
58 XLT O CD latch signal output (Not used)
59 XRST O CD reset signal output
60 DISC-SENS I Slit sensor of disc table input
61 T-SENS I CD table detection signal input
62 VCC – Power supply (+5V)
63 TBL-L O Table motor control output
64 VSS – Ground
65 TBL-R O Table motor control output
66 LOAD-OUT O
Loading motor control signal output
67 LOAD-IN O
68 ENC 3/UP-SW I
69 ENC 2/DISC-LED I Disc tray address detect encoder input
70 ENC 1 I
71 OUT-OPEN O Loading out detection signal output
72 B-TRG O
Trigger motor control output
73 A-TRG O
74 CAP-M-COT2 O Capstan motor control 1(-) signal output
75 CAP-M-COT1 O Capstan motor control 2(-) signal output
76 CAP-M-H/L O Capstan motor H/L speed select signal output
77 AMS-IN I Connected to ground
78 TC-MUTE O TC mute ON/OFF selection output
79 R/PB/PAS O REC/PB/PASS selection output
80 NR-ON/OFF O NR ON/OFF signal output
81 REC-MUTE O REC mute ON/OFF selection output
82 BIAS O Bias ON/OFF selection output
83 EQ-H/N O Equalizer H/N select output
84 PB-A/B O PB Deck A/Deck B select output
85 ALC O ALC ON/OFF output
86 B-PLAY-SW I Deck B play detect
87 A-PLAY-SW I Deck A play detect
88 A-HALF I Deck A cassette detect
89 B-HALF I Deck B cassette detect
90 B-SHUT I B Deck reel pulse detector
91 A-SHUT I A Deck reel pulse detector
92 SOFT-TEST O Software test port
93, 94 KEY/CD-ADJ I CD adjust point port
95 MODEL IN I Version select signal input
96 AVSS – Ground
97 SPEC-IN I Version select signal input
98 VREF I Analog reference voltage input
99 AVCC – Analog power supply
100 TC-RELAY O REC/PB head selection output for IC602
– 88 –
• IC601 DISPLAY CONTROL (TMP88CS76F-6005) (PANEL Board)
1 SIRCS I Remote commander signal input
2 JOG A I Rotary encoder (S601) pulse input
3 L/P SCK O LED/PAD clock output
4 LED LA O LED latch output
5 L/P DAT O LED/PAD data output
6 PAD LA O PAD latch output
7 L SEL O LED select signal
8 JOG B I Rotary encoder (S601) pulse input
9 VOL A I
Rotary encoder (S602) pulse input
10 VOL B I
11 to 14 KEY 0 to KEY 3 I Key input
15 GRADATION L O LED gradation signal (left)
16 S LOW (F01) O Sptctrum analyzer input (Super low flegency) (40Hz)
17 BPF 1 (F02) O Sptctrum analyzer input (100Hz)
18 BPF 2 O Sptctrum analyzer input (400Hz)
19 BPF 3 O Sptctrum analyzer input (2KHz)
20 BPF 4 O Sptctrum analyzer input (6KHz)
21 ALL B (L+R) I Sptctrum analyzer input (all band)
22 GLADATION O
LED gradation signal (right)/WAKE UP signal
R/WAKE UP
23 VSS I/O – Ground
24 VASS – Ground
25 VAref I Analog reference voltage input
26 VDD I/O – Power supply (+5V)
27 to 40 G 18 to G 5 O FL gride signal output
41 VDD VFT – Power supply (+5V)
42 to 45 G 4 to G 1 O FL gride signal output
46 to 67 S 1 to S 22 O FL segment signal output
68 VKK – Power supply (-30V)
69 VDD for CPU – Power supply (+5V)
70 X IN I X’tal (12.5MHz)
71 VSS for CPU – Ground
72 X OUT O X’tal (12.5MHz)
73 RESET I Reset signal input from main controller
74 CH for PAD O Channel signal output for PAD
75 BUSY for PAD O Busy signal output for PAD
76 TEST I Connected ground
77 – – Not used (to ground)
78 IIC DATA O Data output for IC501
79 IIC CLK O Clock output for IC501
80 – – Not used (to ground)
– 89 –
SECTION 9
EXPLODED VIEWS
NOTE: The components identified by
• Items marked “*” are not stocked since they are • Abbreviation mark ! or dotted line with mark
seldom required for routine service. Some delay EA : Saudi Arabia model ! are critical for safety.
should be anticipated when ordering these items. HK : Hong Kong model Replace only with part number
• The mechanical parts with no reference number in SP : Singapore model
specified.
the exploded views are not supplied. MY : Malaysia model
• Hardware (# mark) list and accessories and pack- TW : Taiwan model
ing materials are given in the last of this parts list. IA : Indonesia model
• Color Indication of Appearance Parts Example: TH : Thai model
KNOB, BALANCE (WHITE)
Â
Cabinets color
9-1. CASE SECTION
CDM38L-5BD34L
4
#1
#1
2
#1
3 #2 #2
not supplied
Front panel 2 #2
#13 1 #2
6 11
1 #2
7 6
3
#13 #1
9 10
5 Including Panel board

8
(Ref No. 118)
#1
#1
Including Trans board
#1 (Ref No. 52)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1 4-996-716-01 HOLDER (CDM) 6 4-951-620-01 SCREW (2.6x8), +BVTP
2 3-363-099-41 SCREW (CASE 3 TP2)(GRAY)
2 3-363-099-71 SCREW (CASE 3 TP2)(SILVER) 7 X-4950-965-1 PANEL ASSY, LOADING (VX8)(GRAY)
3 3-363-099-01 SCREW (CASE 3 TP2)(GRAY) 7 X-4951-028-1 PANEL ASSY, LOADING (VX8)(SILVER)
3 3-363-099-11 SCREW (CASE 3 TP2)(SILVER) 7 X-4951-629-1 PANEL ASSY, LOADING (VX8J)
8 4-991-781-01 EMBLEM (VCD)
* 4 4-221-149-21 CASE (SILVER) 9 1-790-927-11 WIRE (FLAT TYPE) (13 CORE)
* 4 4-221-149-61 CASE (GRAY)
5 1-233-545-11 TUNER UNIT (TH) 10 1-775-212-11 WIRE (FLAT TYPE) (23 CORE)
5 1-233-546-13 ENCAPSULATED COMPONENT (EXCEPT TH) 11 A-4724-727-A VIDEO BOARD, COMPLETE
– 90 –
9-2. CHASSIS SECTION
54
53
55 not supplied
#2
#4 61
56
#2
60 #2
#2
not supplied #2
#1
#2
#2
52
63 #2
T951 #3
M901 58 (EA,SP,MY,TW)
#3 #3
58 (E,IA)
58 (HK)
#2
#2 57
59 (E,IA,TH)
59 (EA,HK,SP,MY,TW)
#2
not supplied
62
51
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
51 4-965-822-01 FOOT ! 59 1-575-651-11 CORD, POWER (EA,SP,HK,MY,TW)
* 52 1-672-474-11 TRANS BOARD ! 59 1-575-653-11 CORD, POWER (E,IA,TH)
53 A-4419-149-A MAIN BOARD, COMPLETE (EXCEPT TH, EA) 60 1-773-042-11 WIRE (FLAT TYPE)(17 CORE)
53 A-4419-725-A MAIN BOARD, COMPLETE (EA) 61 4-215-641-01 PANEL, BACK (VX8:EA)
53 A-4426-131-A MAIN BOARD, COMPLETE (TH) 61 4-215-641-11 PANEL, BACK (VX8:SP,MY)
54 A-4419-159-A SURROUND BOARD, COMPLETE 61 4-215-641-21 PANEL, BACK (VX8:TW)

55 1-769-977-11 WIRE (FLAT TYPE)(13 CORE) (TH) 61 4-215-641-31 PANEL, BACK (VX8:E)
55 1-773-009-11 WIRE (FLAT TYPE)(15 CORE) (150mm) 61 4-215-641-41 PANEL, BACK (VX8:IA)
(EXCEPT TH) 61 4-215-641-51 PANEL, BACK (VX8:HK)
56 1-773-024-11 WIRE (FLAT TYPE)(15 CORE) (320mm) 61 4-215-641-61 PANEL, BACK (VX8J:E)
* 57 3-703-244-00 BUSHING (2104), CORD (EXCEPT E,IA,TH)
61 4-215-641-71 PANEL, BACK (VX8J:EA)
57 3-703-571-11 BUSHING (S) (4516), CORD (E,TH) 61 4-215-641-81 PANEL, BACK (VX8:TH)
57 4-966-266-01 BUSHING (S) (FBS002), CORD (IA) 62 3-701-822-01 HOLDER, WIRE
58 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA) 63 4-985-642-01 CUSHION
58 1-569-008-21 ADAPTOR, CONVERSION 2P (EA,SP,MY,TW) M901 1-763-072-11 FAN, D.C.
58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
! T951 1-433-556-11 TRANSFORMER, POWER
– 91 –
9-3. FRONT PANEL SECTION
114 109
119
113 121
109
112
109 118
120
123 FL601
117
122
116
Supplied with
S601 109
106 115
109
109 109
107
109
Supplied with
S602
108 109
111 124
105
103
104 109
110
105
101
110
108
#5
102 #5 TCM230AWR2
TCM230PWR2
#11
not supplied #11
101 X-4950-697-1 HOLDER (L) ASSY, CASSETTE (SILVER) 112 4-962-708-71 EMBLEM (4-A), SONY
101 X-4950-976-1 HOLDER (L) ASSY, CASSETTE (GRAY) 113 X-4951-031-1 PANEL ASSY, FRONT (SILVER)
102 X-4950-698-1 HOLDER (R) ASSY, CASSETTE (SILVER) 113 X-4951-456-1 PANEL ASSY, FRONT (GRAY)
102 X-4950-977-1 HOLDER (R) ASSY, CASSETTE (GRAY) * 114 A-4417-663-A CD SW BOARD, COMPLETE
103 4-214-760-11 CATCHER (A), PUSH 115 4-214-385-11 KNOB (MIC)(SILVER)
104 4-214-761-11 CATCHER (B), PUSH 115 4-214-385-51 KNOB (MIC)(GRAY)

105 4-214-775-01 SPRING, PUSH CATCHER RETURN 116 1-773-223-11 WIRE (FLAT TYPE)(25 CORE)
106 4-214-383-11 KNOB (JOG)(SILVER) * 117 4-214-439-11 HOLDER, FL TUBE
106 4-214-383-51 KNOB (JOG)(GRAY) 118 A-4419-146-A PANEL BOARD, COMPLETE
107 4-214-384-11 KNOB (VOL)(SILVER) * 119 4-214-736-11 HOLDER (L)(LED)
107 4-214-384-51 KNOB (VOL)(GRAY) * 120 4-214-737-11 HOLDER (R)(LED)

108 4-219-087-01 SPRING, TENSION * 121 4-214-738-11 INDICATOR (ILLUMINATION 1)
109 4-951-620-01 SCREW (2.6X8), +BVTP 122 1-675-195-11 PUSH CATCH STOPPER (A)
110 4-215-062-01 DAMPER * 123 4-949-935-51 CUSHION (FL)
111 4-930-336-61 FOOT (FELT) 124 1-675-196-11 PUSH CATCH STOPPER (B)
FL601 1-517-831-31 INDICATOR TUBE, FLUORESCENT
– 92 –
9-4. CD MECHANISM DECK SECTION-1 (CDM38L-5BD34L)
201
202
201 206
#2
203 M701
204
211 #6
205
207
208
210
212
209
#2
201 4-981-789-21 BRACKET (2), YOKE 207 4-988-162-01 ROLLER
202 4-977-945-63 TRAY (TURN) 208 4-977-941-01 BEARING (WORM)
203 X-4946-665-1 SHAFT ASSY, WORM * 209 1-658-576-11 SENSOR BOARD
204 4-977-943-01 BELT (TURN) (1.2) 210 4-934-376-01 SHAFT (ROLLER)
205 4-977-956-01 WHEEL, WORM
211 4-981-187-01 COLLAR (WORM)
* 206 1-658-577-11 MOTOR (TURN) BOARD 212 4-977-944-01 TRAY (SLIDE)
M701 A-4672-004-A MOTOR ASSY (TURN)
– 93 –
9-5. CD MECHANISM DECK SECTION-2 (CDM38L-5BD34L)
251
251 253 252
255
254
#7
257
not supplied
258
251 260
256
270
not supplied
259
266
#2
271
267
269
268
261 272
261 M801
BU-5BD32L
S811 262
263
#2
263
264
265
251
251 4-981-789-11 BRACKET (2), YOKE 263 4-982-447-01 SPRING (BU), COMPRESSION
252 4-977-954-01 PULLEY (SL) 264 4-951-620-41 SCREW (2.6), +BVTP
253 4-977-953-01 GEAR (SL-A) 265 X-4949-570-1 HOLDER (BU) ASSY
254 4-977-955-01 GEAR (SL-B)
255 4-977-942-01 BELT (SL) (1.4) 266 4-989-494-01 SCREW (SLIDER), STEP
267 4-989-492-11 SLIDER (38)
256 X-4946-667-1 CAM ASSY, BU 268 4-989-819-02 SPRING, TENSION
257 1-452-925-21 MAGNET ASSY 269 4-989-491-11 COVER, LENS
258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE) 270 4-993-142-21 PULLEY (L), PRESS
* 259 1-658-575-11 CONNECTOR BOARD
260 4-900-743-01 SPRING, COMPRESSION * 271 4-900-718-01 BRACKET (ADJUSTMENT)
272 X-4950-020-2 CHASSIS (CDM) ASSY
261 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING S811 1-473-335-11 ENCODER, ROTARY
* 262 1-658-578-11 MOTOR (SLIDE) BOARD M801 A-4672-004-A MOTOR ASSY (SLIDE)
– 94 –
9-6. BASE UNIT SECTION (BU-5BD34L)
301
302
309
303
305
M101 304
M102
304
306
307
308
Replace only with part number specified.
! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP 306 4-917-564-01 GEAR (P), FLATNESS
302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE) 307 A-4724-640-A BD BOARD, COMPLETE
303 4-917-567-01 GEAR (M) 308 4-951-620-01 SCREW (2.6X8), +BVTP
304 4-951-940-01 INSULATOR (BU) 309 3-713-786-51 SCREW +P 2X3
305 4-917-565-01 SHAFT, SLED M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
M102 X-4917-504-1 MOTOR ASSY (SLED)
– 95 –
9-7. TC MECHANISM SECTION-1 (TCM230AWR2/230PWR2)
*NOTE: Two types of parts which are not interchangeable are available
for the Head deck (A) ASSY and Head deck (B) ASSY.
When replacing the parts, refer to the following figure, and use the
appropriate part.
408
Parts with “P” mark: 230PWR2
Parts without “P” mark: 230AWR2
412 408
413
407
406
404
HP101
403
407
HRPE101 403 405

406 410
411
404
405
409
402
402
401
401 3-376-464-11 SCREW(+PTT 2.6X6),GROUND POINT 410 3-016-573-01 LEVER (EJECT PREVENTION R)
402 3-036-914-01 RIVET
403 3-016-574-11 SPRING (HEAD), TENSION 411 3-032-810-02 SPRING (R), TORSION
404 X-3374-156-4 PINCH LEVER (REV) ASSY 412 3-016-572-01 LEVER (EJECT PREVENTION L)
405 X-3374-155-4 PINCH LEVER (FWD) ASSY 413 3-032-809-02 SPRING (L), TORSION
HP101 A-2056-681-B DECK (A) ASSY, HEAD (230AWR2)(*NOTE)
406 3-016-564-01 BASE (PINCH LEVER FWD) HP101 A-2056-683-B DECK (A) ASSY, HEAD (230PWR2)(*NOTE)
407 3-016-565-01 BASE (PINCH LEVER REV)
408 3-026-892-01 SPRING (CASSETTE), LEAF HRPE101 A-2056-682-B DECK (B) ASSY, HEAD (230AWR2)(*NOTE)
* 409 A-2007-731-A AUDIO BOARD, COMPLETE HRPE101 A-2056-684-B DECK (B) ASSY, HEAD (230PWR2)(*NOTE)
– 96 –
9-8. TC MECHANISM SECTION-2 (TCM230AWR2/230PWR2)
*NOTE: Two types of parts which are not interchangeable are available
for the mechanical block assembly. When replacing the parts,
refer to the following figure, and use the appropriate part.
Parts with “P” mark: 230PWR2

Parts without “P” mark: 230AWR2
461
451
#8
462
459
465 460 463

458
455 #10
465
#9
465
460
452 454
456 465 464
459
458
455
452
M1
456
457
453
* 451 X-3374-214-3 CHASSIS ASSY, MAIN 459 A-2004-629-B MECHANICAL BLOCK ASSY (230PWR2)(*NOTE)
452 3-016-570-01 BELT (CAPSTAN)
453 3-016-569-01 BELT (TENSION) 460 3-016-566-01 SLIDER, REVERSE
454 3-017-360-01 BRACKET (MOTOR) * 461 A-2007-732-A LEAF SW BOARD, COMPLETE
455 X-3376-497-1 FLYWHEEL (FWD) ASSY 462 3-016-575-11 SPRING, TORSION
463 3-019-208-01 WASHER, STOPPER
456 X-3374-235-1 FLYWHEEL (REV) ASSY 464 3-027-453-01 SPRING (GROUND), TENSION
457 X-3374-238-1 PULLEY ASSY, TENSION
458 3-024-405-01 BELT (FR2) 465 3-030-823-01 SCREW (+BVTT) (2X3.5)
459 A-2004-629-A MECHANICAL BLOCK ASSY (230AWR2)(*NOTE) M1 A-2004-628-A MOTOR ASSY, CAPSTAN
– 97 –
SECTION 10
AUDIO ELECTRICAL PARTS LIST
Note:
The components identified by • Due to standardization, replacements in the parts list • CAPACITORS
mark ! or dotted line with mark may be different from the parts specified in the uF : µ F
! are critical for safety. diagrams or the components used on the set. • COILS
Replace only with part number • -XX, -X mean standardized parts, so they may have uH : µ H
specified. some difference from the original one. • Abbreviation
• Items marked “*” are not stocked since they are EA : Saudi Arabia model
seldom required for routine service. Some delay HK : Hong Kong model
When indicating parts by reference should be anticipated when ordering these items. SP : Singapore model
number, please include the board • RESISTORS MY : Malaysia model
name. All resistors are in ohms TW : Taiwan model
METAL: Metal-film resistor IA : Indonesia model
METAL OXIDE: Metal Oxide-film resistor TH : Thai model
F : nonflammable
• SEMICONDUCTORS
In each case, u: µ , for example:
uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,
uPC...: µ PC..., uPD...: µ PD...
* A-2007-731-A AUDIO BOARD, COMPLETE < IC >
*********************
IC601 8-759-111-44 IC UPC4570C-1
< CAPACITOR > IC602 8-759-143-54 IC UPC1330HA
IC611 8-759-111-44 IC UPC4570C-1
C301 1-162-289-31 CERAMIC 390PF 10% 50V
C302 1-126-968-11 ELECT 100uF 20% 6.3V < COIL >
C303 1-162-282-31 CERAMIC 100PF 10% 50V
C304 1-130-483-00 MYLAR 0.01uF 5% 50V L331 1-410-780-11 INDUCTOR 27mH
C305 1-107-715-11 ELECT 22uF 20% 16V L431 1-410-780-11 INDUCTOR 27mH
L601 1-414-193-41 INDUCTOR 220uH
C311 1-162-289-31 CERAMIC 390PF 10% 50V L602 1-414-193-41 INDUCTOR 220uH
C313 1-162-282-31 CERAMIC 100PF 10% 50V
C314 1-130-487-00 MYLAR 0.022uF 5% 50V < TRANSISTOR >
C315 1-126-233-11 ELECT 22uF 20% 50V
C331 1-137-427-11 FILM 120PF 5% 50V Q621 8-729-142-46 TRANSISTOR 2SC2001-LK
Q622 8-729-142-46 TRANSISTOR 2SC2001-LK
C332 1-162-288-31 CERAMIC 330PF 10% 50V Q623 8-729-801-93 TRANSISTOR 2SD1387
C333 1-162-209-31 CERAMIC 27PF 5% 50V
C401 1-162-289-31 CERAMIC 390PF 10% 50V < RESISTOR >
C402 1-126-968-11 ELECT 100uF 20% 6.3V
C403 1-162-282-31 CERAMIC 100PF 10% 50V R301 1-247-881-00 CARBON 120K 5% 1/4W
R302 1-249-409-11 CARBON 220 5% 1/4W F
C404 1-130-483-00 MYLAR 0.01uF 5% 50V R303 1-249-433-11 CARBON 22K 5% 1/4W
C405 1-107-715-11 ELECT 22uF 20% 16V R304 1-247-889-00 CARBON 270K 5% 1/4W
C413 1-162-282-31 CERAMIC 100PF 10% 50V
R312 1-247-807-31 CARBON 100 5% 1/4W
C431 1-137-427-11 FILM 120PF 5% 50V R315 1-247-850-11 CARBON 6.2K 5% 1/4W
C433 1-162-209-31 CERAMIC 27PF 5% 50V
R402 1-249-409-11 CARBON 220 5% 1/4W F
C621 1-137-150-11 FILM 0.01uF 5% 100V
C622 1-126-961-11 ELECT 2.2uF 20% 50V R411 1-247-881-00 CARBON 120K 5% 1/4W
R412 1-247-807-31 CARBON 100 5% 1/4W
C623 1-136-155-00 FILM 0.015uF 5% 50V R414 1-247-882-11 CARBON 130K 5% 1/4W
C624 1-130-481-00 MYLAR 0.0068uF 5% 50V R415 1-247-850-11 CARBON 6.2K 5% 1/4W
C627 1-124-903-11 ELECT 1uF 20% 50V
C628 1-136-153-00 FILM 0.01uF 5% 50V R601 1-249-409-11 CARBON 220 5% 1/4W F
R602 1-249-409-11 CARBON 220 5% 1/4W F
C642 1-104-664-11 ELECT 47uF 20% 16V R608 1-249-409-11 CARBON 220 5% 1/4W F
R609 1-249-433-11 CARBON 22K 5% 1/4W
< CONNECTOR > R611 1-249-409-11 CARBON 220 5% 1/4W F
CN601 1-695-338-11 PIN, CONNECTOR (PC BOARD) 15P R612 1-249-409-11 CARBON 220 5% 1/4W F
! R621 1-212-851-00 FUSIBLE 5.6 5% 1/4W F
– 98 –
AUDIO BD
! R622 1-212-851-00 FUSIBLE 5.6 5% 1/4W F C171 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R623 1-249-432-11 CARBON 18K 5% 1/4W
R624 1-249-432-11 CARBON 18K 5% 1/4W < CONNECTOR >
R625 1-249-429-11 CARBON 10K 5% 1/4W CN101 1-770-706-11 CONNECTOR, FFC/FPC 23P
CN102 1-777-937-11 CONNECTOR, FFC/FPC 16P
< VARIABLE RESISTOR >
< IC >
RV301 1-238-598-11 RES, ADJ, CARBON 2.2K
RV311 1-238-598-11 RES, ADJ, CARBON 2.2K IC101 8-752-397-42 IC CXD3008Q
RV341 1-241-768-11 RES, ADJ, CARBON 220K IC102 8-759-549-28 IC BA5974FP-E2
RV401 1-238-598-11 RES, ADJ, CARBON 2.2K IC103 8-752-085-51 IC CXA2568M-T6
RV411 1-238-598-11 RES, ADJ, CARBON 2.2K IC104 8-759-398-25 IC TC7SH04F(TE85L)
RV441 1-241-768-11 RES, ADJ, CARBON 220K < COIL >
< TRANSFORMER > L101 1-414-234-22 INDUCTOR CHIP 0uH

L102 1-410-377-31 INDUCTOR CHIP 4.7uH
T621 1-423-980-11 TRANSFORMER, BIAS OSCILLATION
< TRANSISTOR >
**************************************************************
Q101 8-729-010-08 TRANSISTOR MSB710-R
A-4724-640-A BD BOARD, COMPLETE
****************** < RESISTOR >
< CAPACITOR > R101 1-216-077-00 METAL CHIP 15K 5% 1/10W

R102 1-216-097-91 RES,CHIP 100K 5% 1/10W
C101 1-163-005-11 CERAMIC CHIP 470PF 10% 50V R103 1-216-077-00 METAL CHIP 15K 5% 1/10W
C102 1-163-038-91 CERAMIC CHIP 0.1uF 25V R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
C105 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C106 1-164-346-11 CERAMIC CHIP 1uF 16V R106 1-216-049-91 RES,CHIP 1K 5% 1/10W
R107 1-216-073-00 METAL CHIP 10K 5% 1/10W
C107 1-164-346-11 CERAMIC CHIP 1uF 16V R108 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C108 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V R109 1-216-121-91 RES,CHIP 1M 5% 1/10W
C109 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V R110 1-216-295-91 SHORT 0
C110 1-164-161-11 CERAMIC CHIP 0.0022uF 10% 100V
C111 1-163-251-11 CERAMIC CHIP 100PF 5% 50V R112 1-216-049-91 RES,CHIP 1K 5% 1/10W
R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
C112 1-163-038-91 CERAMIC CHIP 0.1uF 25V R124 1-216-097-91 RES,CHIP 100K 5% 1/10W
C113 1-163-038-91 CERAMIC CHIP 0.1uF 25V R125 1-216-037-00 METAL CHIP 330 5% 1/10W
C115 1-126-607-11 ELECT CHIP 47uF 20% 4V R126 1-216-037-00 METAL CHIP 330 5% 1/10W
C116 1-126-607-11 ELECT CHIP 47uF 20% 4V
C117 1-126-209-11 ELECT CHIP 100uF 20% 4V R127 1-216-037-00 METAL CHIP 330 5% 1/10W
R131 1-216-037-00 METAL CHIP 330 5% 1/10W
C119 1-163-110-00 CERAMIC CHIP 51PF 5% 50V R136 1-216-295-91 SHORT 0
C120 1-109-982-11 CERAMIC CHIP 1uF 10% 10V R137 1-216-295-91 SHORT 0
C121 1-109-982-11 CERAMIC CHIP 1uF 10% 10V
R143 1-216-103-00 METAL CHIP 180K 5% 1/10W
C123 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V R144 1-216-103-00 METAL CHIP 180K 5% 1/10W
C124 1-164-005-11 CERAMIC CHIP 0.47uF 25V R145 1-216-121-91 RES,CHIP 1M 5% 1/10W
C126 1-124-779-00 ELECT CHIP 10uF 20% 16V R146 1-216-121-91 RES,CHIP 1M 5% 1/10W
C130 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C140 1-163-038-91 CERAMIC CHIP 0.1uF 25V R147 1-216-041-00 METAL CHIP 470 5% 1/10W
R148 1-216-001-00 METAL CHIP 10 5% 1/10W
C141 1-163-038-91 CERAMIC CHIP 0.1uF 25V R149 1-216-003-11 RES,CHIP 12 5% 1/10W
C153 1-163-038-91 CERAMIC CHIP 0.1uF 25V R154 1-216-025-91 RES,CHIP 100 5% 1/10W
C156 1-163-235-11 CERAMIC CHIP 22PF 5% 50V R155 1-216-025-91 RES,CHIP 100 5% 1/10W
R156 1-216-025-91 RES,CHIP 100 5% 1/10W
C157 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R157 1-216-025-91 RES,CHIP 100 5% 1/10W
C159 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V R158 1-216-111-00 METAL CHIP 390K 5% 1/10W
C161 1-163-038-91 CERAMIC CHIP 0.1uF 25V R159 1-216-089-91 RES,CHIP 47K 5% 1/10W
C162 1-128-065-11 ELECT CHIP 68uF 20% 10V
C170 1-163-038-91 CERAMIC CHIP 0.1uF 25V R161 1-216-308-00 METAL CHIP 4.7 5% 1/10W

– 99 – Replace only with part number specified.
BD CD SW CONNECTOR LEAF SW
R162 1-216-101-00 METAL CHIP 150K 5% 1/10W < TRANSISTOR >
R171 1-216-025-91 RES,CHIP 100 5% 1/10W
R172 1-216-025-91 RES,CHIP 100 5% 1/10W Q701 8-729-900-80 TRANSISTOR DTC114ES
R173 1-216-025-91 RES,CHIP 100 5% 1/10W
< RESISTOR >
R175 1-216-025-91 RES,CHIP 100 5% 1/10W
R203 1-216-025-91 RES,CHIP 100 5% 1/10W R703 1-249-435-11 CARBON 33K 5% 1/4W
R205 1-216-025-91 RES,CHIP 100 5% 1/10W R705 1-249-417-11 CARBON 1K 5% 1/4W F
R206 1-216-295-91 SHORT 0
**************************************************************
< SWITCH >
* A-2007-732-A LEAF SW BOARD, COMPLETE
S101 1-572-085-11 SWITCH, LEAF (LIMIT SW) ************************
************************************************************** < CAPACITOR >
* A-4417-663-A CD SW BOARD, COMPLETE C1001 1-107-716-11 ELECT 33uF 20% 10V

*********************
< CONNECTOR >
< DIODE >
CN1001 1-568-860-11 SOCKET, CONNECTOR 17P
D801 8-719-056-13 DIODE SML79423C-TP15 (DISC 3) CN1001 1-784-459-11 CONNECTOR, FFC/FPC 17P
D802 8-719-056-13 DIODE SML79423C-TP15 (DISC 2)
D803 8-719-056-13 DIODE SML79423C-TP15 (DISC 1) < DIODE >
D804 8-719-063-93 DIODE SLR325VC-N-T32 (1/u)
D1001 8-719-911-19 DIODE 1SS119
< RESISTOR > D1002 8-719-911-19 DIODE 1SS119
R801 1-216-049-91 RES,CHIP 1K 5% 1/10W < HOLDER >

R802 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R803 1-216-055-00 METAL CHIP 1.8K 5% 1/10W * DM1001 1-784-581-11 HOLDER, CABLE (2.5MM PITCH) 4P
R804 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R805 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < IC >
R806 1-216-065-91 RES,CHIP 4.7K 5% 1/10W IC1001 8-749-014-38 IC PHOTO INTERRUPTER SG-264
R807 1-216-069-00 METAL CHIP 6.8K 5% 1/10W IC1002 8-749-014-38 IC PHOTO INTERRUPTER SG-264
R808 1-216-022-00 METAL CHIP 75 5% 1/10W
R809 1-216-029-00 METAL CHIP 150 5% 1/10W < TRANSISTOR >
R810 1-216-022-00 METAL CHIP 75 5% 1/10W
Q1001 8-729-029-56 TRANSISTOR DTA144ESA
R811 1-216-029-00 METAL CHIP 150 5% 1/10W
R812 1-216-022-00 METAL CHIP 75 5% 1/10W < RESISTOR >
R813 1-216-029-00 METAL CHIP 150 5% 1/10W
R1001 1-249-409-11 CARBON 220 5% 1/4W F
< SWITCH > R1002 1-249-409-11 CARBON 220 5% 1/4W F
R1003 1-249-414-11 CARBON 560 5% 1/4W F
S801 1-762-875-21 SWITCH, KEYBOARD (1/u) R1004 1-247-834-11 CARBON 1.3K 5% 1/4W
S802 1-762-875-21 SWITCH, KEYBOARD (DEMO (STANDBY))
S803 1-762-875-21 SWITCH, KEYBOARD (DISC 1) R1005 1-247-818-11 CARBON 300 5% 1/4W
S804 1-762-875-21 SWITCH, KEYBOARD (DISC 2) R1006 1-247-864-11 CARBON 24K 5% 1/4W
S805 1-762-875-21 SWITCH, KEYBOARD (DISC 3) R1007 1-247-856-00 CARBON 11K 5% 1/4W
R1008 1-249-417-11 CARBON 1K 5% 1/4W F
S806 1-762-875-21 SWITCH, KEYBOARD (DISC SKIP/EX-CHANGE)
S807 1-762-875-21 SWITCH, KEYBOARD (§) < VARIABLE RESISTOR >
************************************************************** RV1001 1-241-785-11 RES, ADJ, CARBON 10K

RV1002 1-241-785-11 RES, ADJ, CARBON 10K
* 1-658-575-11 CONNECTOR BOARD
***************** < SWITCH >
< CONNECTOR > S1001 1-570-953-11 SWITCH, PUSH (1 KEY)(A PLAY)

S1002 1-570-953-11 SWITCH, PUSH (1 KEY)(B PLAY)
* CN701 1-568-946-11 PIN, CONNECTOR 8P S1003 1-771-333-11 SWITCH, LEAF (A HALF)
CN702 1-750-413-11 CONNECTOR, FFC/FPC 8P S1004 1-771-205-11 SWITCH, LEAF (A 120/70)
S1005 1-771-205-11 SWITCH, LEAF (REC A)
– 100 –
LEAF SW MAIN
S1006 1-771-333-11 SWITCH, LEAF (B HALF) C193 1-126-964-11 ELECT 10uF 20% 50V
S1008 1-771-205-11 SWITCH, LEAF (B 120/70) C197 1-162-306-11 CERAMIC 0.01uF 20% 16V
S1009 1-771-205-11 SWITCH, LEAF (REC B) C301 1-126-960-11 ELECT 1uF 20% 50V
C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
**************************************************************
C303 1-136-165-00 FILM 0.1uF 5% 50V
A-4419-149-A MAIN BOARD, COMPLETE (EXCEPT EA,TH) C304 1-136-165-00 FILM 0.1uF 5% 50V
******************** C305 1-126-964-11 ELECT 10uF 20% 50V
C306 1-126-960-11 ELECT 1uF 20% 50V
A-4419-725-A MAIN BOARD, COMPLETE (EA) C307 1-126-959-11 ELECT 0.47uF 20% 50V
********************
C308 1-126-964-11 ELECT 10uF 20% 50V
A-4426-131-A MAIN BOARD, COMPLETE (TH) C309 1-137-194-81 FILM 0.47uF 5% 50V
******************** C310 1-162-290-31 CERAMIC 470PF 10% 50V
C311 1-126-964-11 ELECT 10uF 20% 50V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C312 1-126-959-11 ELECT 0.47uF 20% 50V
< CAPACITOR > C313 1-162-294-31 CERAMIC 0.001uF 10% 50V

C314 1-126-964-11 ELECT 10uF 20% 50V
C104 1-164-159-11 CERAMIC 0.1uF 50V C315 1-126-963-11 ELECT 4.7uF 20% 50V
C111 1-137-195-11 FILM 0.56uF 5% 50V C316 1-104-665-11 ELECT 100uF 20% 10V
C113 1-136-167-00 FILM 0.15uF 5% 50V
C114 1-130-480-00 MYLAR 0.0056uF 5% 50V C320 1-162-290-31 CERAMIC 470PF 10% 50V
C333 1-162-600-11 CERAMIC 0.0047uF 30% 16V
C115 1-136-159-00 FILM 0.033uF 5% 50V C334 1-162-600-11 CERAMIC 0.0047uF 30% 16V
C116 1-130-473-00 MYLAR 0.0015uF 5% 50V C351 1-126-960-11 ELECT 1uF 20% 50V
C117 1-136-153-00 FILM 0.01uF 5% 50V C352 1-130-479-00 MYLAR 0.0047uF 5% 50V
C118 1-162-288-31 CERAMIC 330PF 10% 50V
C119 1-130-479-00 MYLAR 0.0047uF 5% 50V C353 1-136-165-00 FILM 0.1uF 5% 50V
C354 1-136-165-00 FILM 0.1uF 5% 50V
C121 1-126-964-11 ELECT 10uF 20% 50V C356 1-126-960-11 ELECT 1uF 20% 50V
C122 1-162-291-31 CERAMIC 560PF 10% 50V C357 1-126-959-11 ELECT 0.47uF 20% 50V
C123 1-136-169-00 FILM 0.22uF 5% 50V
C359 1-137-194-81 FILM 0.47uF 5% 50V
C131 1-104-664-11 ELECT 47uF 20% 16V C390 1-104-656-11 ELECT 2200uF 20% 6.3V
C132 1-104-664-11 ELECT 47uF 20% 16V C391 1-161-494-00 CERAMIC 0.022uF 25V
C135 1-126-964-11 ELECT 10uF 20% 50V
C141 1-126-959-11 ELECT 0.47uF 20% 50V C392 1-126-916-11 ELECT 1000uF 20% 6.3V
C393 1-161-494-00 CERAMIC 0.022uF 25V
C162 1-136-158-00 FILM 0.027uF 5% 50V C396 1-126-961-11 ELECT 2.2uF 20% 50V
C164 1-130-480-00 MYLAR 0.0056uF 5% 50V
C411 1-162-306-11 CERAMIC 0.01uF 20% 16V
C168 1-162-288-31 CERAMIC 330PF 10% 50V C433 1-126-961-11 ELECT 2.2uF 20% 50V
C169 1-130-479-00 MYLAR 0.0047uF 5% 50V
C501 1-126-964-11 ELECT 10uF 20% 50V
C171 1-126-964-11 ELECT 10uF 20% 50V C502 1-164-159-11 CERAMIC 0.1uF 50V
C172 1-162-291-31 CERAMIC 560PF 10% 50V C503 1-136-165-00 FILM 0.1uF 5% 50V
C174 1-136-169-00 FILM 0.22uF 5% 50V
C610 1-102-953-00 CERAMIC 18PF 5% 50V
C176 1-136-495-11 FILM 0.068uF 5% 50V C611 1-102-514-11 CERAMIC 22PF 5% 50V
C177 1-136-153-00 FILM 0.01uF 5% 50V C614 1-162-306-11 CERAMIC 0.01uF 20% 16V
C181 1-161-494-00 CERAMIC 0.022uF 25V C616 1-104-665-11 ELECT 100uF 20% 10V
C182 1-161-494-00 CERAMIC 0.022uF 25V
C183 1-126-964-11 ELECT 10uF 20% 50V C662 1-162-306-11 CERAMIC 0.01uF 20% 16V
C664 1-104-665-11 ELECT 100uF 20% 10V
C184 1-126-964-11 ELECT 10uF 20% 50V C698 1-162-306-11 CERAMIC 0.01uF 20% 16V
– 101 –
MAIN
C699 1-104-665-11 ELECT 100uF 20% 10V CN391 1-750-745-11 CONNECTOR, FFC/FPC 13P
C801 1-126-963-11 ELECT 4.7uF 20% 50V
CN392 1-785-334-11 PIN, CONNECTOR (LIGHT ANGLE)8P
C802 1-162-290-31 CERAMIC 470PF 10% 50V CN393 1-785-335-11 PIN, CONNECTOR (LIGHT ANGLE)9P
C803 1-162-282-31 CERAMIC 100PF 10% 50V * CN403 1-564-518-11 PLUG, CONNECTOR 3P
C804 1-104-665-11 ELECT 100uF 20% 10V * CN501 1-568-841-11 SOCKET, CONNECTOR 25P
C807 1-136-495-11 FILM 0.068uF 5% 50V
C808 1-136-495-11 FILM 0.068uF 5% 50V < DIODE >
C809 1-128-560-11 ELECT 22uF 20% 100V D141 8-719-911-19 DIODE 1SS119-25
C811 1-162-306-11 CERAMIC 0.01uF 20% 16V D331 8-719-911-19 DIODE 1SS119-25
C812 1-162-306-11 CERAMIC 0.01uF 20% 16V D333 8-719-911-19 DIODE 1SS119-25
C843 1-136-165-00 FILM 0.1uF 5% 50V D401 8-719-911-19 DIODE 1SS119-25
C851 1-126-963-11 ELECT 4.7uF 20% 50V D405 8-719-024-99 DIODE 11ES2-NTA2B
C852 1-162-290-31 CERAMIC 470PF 10% 50V D406 8-719-024-99 DIODE 11ES2-NTA2B
C853 1-162-282-31 CERAMIC 100PF 10% 50V D407 8-719-024-99 DIODE 11ES2-NTA2B
C857 1-136-495-11 FILM 0.068uF 5% 50V D501 8-719-024-99 DIODE 11ES2-NTA2B

C904 1-104-664-11 ELECT 47uF 20% 16V D802 8-719-118-97 DIODE RD16F-T7B2
C906 1-136-165-00 FILM 0.1uF 5% 50V D831 8-719-302-37 DIODE RBV-602

C907 1-128-548-11 ELECT 4700uF 20% 25V D832 8-719-060-53 DIODE RBV-2506
C910 1-104-665-11 ELECT 100uF 20% 10V D852 8-719-118-97 DIODE RD16F-T7B2
C912 1-126-926-11 ELECT 1000uF 20% 10V D901 8-719-975-85 DIODE ERB83-004
C916 1-162-306-11 CERAMIC 0.01uF 20% 16V D905 8-719-933-36 DIODE HZS6B1L
C921 1-104-656-11 ELECT 2200uF 20% 6.3V D907 8-719-024-99 DIODE 11ES2-NTA2B
C922 1-126-964-11 ELECT 10uF 20% 50V D908 8-719-024-99 DIODE 11ES2-NTA2B
C952 1-126-768-11 ELECT 2200uF 20% 16V D915 8-719-935-69 DIODE HZS11B1LTA
D921 8-719-911-19 DIODE 1SS119-25
< CONNECTOR >
D922 8-719-911-19 DIODE 1SS119-25
CN303 1-784-776-11 CONNECTOR, FFC 15P D923 8-719-911-19 DIODE 1SS119-25
CN304 1-784-778-11 CONNECTOR, FFC 17P D924 8-719-024-99 DIODE 11ES2-NTA2B
* CN371 1-568-832-11 SOCKET, CONNECTOR 13P (VX8:TH) D925 8-719-024-99 DIODE 11ES2-NTA2B
CN371 1-568-834-11 SOCKET, CONNECTOR 15P (EXCEPT VX8:TH)
– 102 –
MAIN
< FERRITE BEAD > Q432 8-729-140-82 TRANSISTOR 2SA988-PAFAEA
FB391 1-412-493-21 INDUCTOR Q433 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA

FB392 1-412-493-21 INDUCTOR Q434 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q435 8-729-900-36 TRANSISTOR DTC124ES
< IC > Q436 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q437 8-729-119-79 TRANSISTOR 2SC2785-FEK
IC101 8-759-571-54 IC M62493FP
IC181 8-759-634-51 IC M5218AP Q439 8-729-119-79 TRANSISTOR 2SC2785-FEK
IC301 8-759-495-26 IC HA12215 Q471 8-729-141-30 TRANSISTOR 2SC3623A-LK
IC381 8-749-923-04 IC TOTX178 Q501 8-729-119-78 TRANSISTOR 2SC403SP-51
IC501 8-759-588-91 IC M30622MA-A09FP Q508 8-729-900-63 TRANSISTOR DTA124ES
Q509 8-729-900-63 TRANSISTOR DTA124ES
IC502 8-759-635-63 IC M51943BSL
IC801 8-749-015-37 IC STK411-240E Q801 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
IC901 8-759-604-86 IC M5F7807L Q803 8-729-140-82 TRANSISTOR 2SA988-PAFAEA
IC902 8-759-231-53 IC TA7805S Q804 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
IC903 8-759-088-08 IC UPC7812AHF Q831 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q832 8-729-119-79 TRANSISTOR 2SC2785-FEK
IC904 8-759-231-53 IC TA7805S
Q851 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
< JACK > Q881 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA
Q901 8-729-209-15 TRANSISTOR 2SD2012
J101 1-774-411-11 JACK, PIN 6P (VIDEO AUDIO IN, MD IN/OUT) Q902 8-729-119-78 TRANSISTOR 2SC403SP-51
J191 1-774-785-11 JACK, PIN 1P (SUPER WOOFER) Q903 8-729-900-36 TRANSISTOR DTC124ES
< COIL > Q904 8-729-900-36 TRANSISTOR DTC124ES

Q905 8-729-040-20 TRANSISTOR RT1P137L-TP
L381 1-410-521-11 INDUCTOR 100uH Q907 8-729-141-83 TRANSISTOR 2SB1094-LK
L392 1-410-521-11 INDUCTOR 100uH Q908 8-729-900-36 TRANSISTOR DTC124ES
L501 1-410-509-11 INDUCTOR 10uH Q909 8-729-026-68 TRANSISTOR 2SD2525(TP)
< TRANSISTOR > Q911 8-729-141-83 TRANSISTOR 2SB1094-LK

Q111 8-729-119-78 TRANSISTOR 2SC403SP-51 Q913 8-729-119-78 TRANSISTOR 2SC403SP-51
Q112 8-729-119-78 TRANSISTOR 2SC403SP-51 Q914 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q113 8-729-141-30 TRANSISTOR 2SC3623A-LK Q923 8-729-900-36 TRANSISTOR DTC124ES
Q161 8-729-119-78 TRANSISTOR 2SC403SP-51
Q162 8-729-119-78 TRANSISTOR 2SC403SP-51 Q951 8-729-141-83 TRANSISTOR 2SB1094-LK
Q952 8-729-119-77 TRANSISTOR 2SA1175-FEK
Q163 8-729-141-30 TRANSISTOR 2SC3623A-LK
Q181 8-729-141-30 TRANSISTOR 2SC3623A-LK < RESISTOR >
Q191 8-729-141-30 TRANSISTOR 2SC3623A-LK
Q192 8-729-900-63 TRANSISTOR DTA124ES R101 1-249-417-11 CARBON 1K 5% 1/4W F
Q201 8-729-900-36 TRANSISTOR DTC124ES R102 1-249-417-11 CARBON 1K 5% 1/4W F
R103 1-249-417-11 CARBON 1K 5% 1/4W F
Q251 8-729-900-36 TRANSISTOR DTC124ES R111 1-249-429-11 CARBON 10K 5% 1/4W
Q331 8-729-118-00 TRANSISTOR 2SB1116-L R112 1-247-895-00 CARBON 470K 5% 1/4W
Q333 8-729-118-00 TRANSISTOR 2SB1116-L R113 1-247-894-11 CARBON 430K 5% 1/4W
Q334 8-729-900-80 TRANSISTOR DTC114ES R114 1-249-415-11 CARBON 680 5% 1/4W F
R115 1-249-433-11 CARBON 22K 5% 1/4W
Q335 8-729-900-80 TRANSISTOR DTC114ES R116 1-247-887-00 CARBON 220K 5% 1/4W
Q336 8-729-116-59 TRANSISTOR 2SB1068TP R117 1-249-429-11 CARBON 10K 5% 1/4W
Q337 8-729-045-21 TRANSISTOR 2SD1513TP-LK
Q338 8-729-422-57 TRANSISTOR UN4111 R118 1-249-437-11 CARBON 47K 5% 1/4W
Q339 8-729-900-80 TRANSISTOR DTC114ES R119 1-249-421-11 CARBON 2.2K 5% 1/4W F
R120 1-249-441-11 CARBON 100K 5% 1/4W
Q340 8-729-116-59 TRANSISTOR 2SB1068TP R121 1-249-429-11 CARBON 10K 5% 1/4W
Q341 8-729-045-21 TRANSISTOR 2SD1513TP-LK R124 1-249-433-11 CARBON 22K 5% 1/4W F
Q342 8-729-422-57 TRANSISTOR UN4111
Q343 8-729-900-80 TRANSISTOR DTC114ES R125 1-247-843-11 CARBON 3.3K 5% 1/4W
Q401 8-729-119-77 TRANSISTOR 2SA1175-FEK R126 1-249-421-11 CARBON 2.2K 5% 1/4W F
R130 1-249-433-11 CARBON 22K 5% 1/4W
Q402 8-729-111-29 TRANSISTOR 2SD1616A-K R131 1-247-807-31 CARBON 100 5% 1/4W
Q411 8-729-141-30 TRANSISTOR 2SC3623A-LK R132 1-247-807-31 CARBON 100 5% 1/4W
Q412 8-729-900-63 TRANSISTOR DTA124ES
Q431 8-729-140-84 TRANSISTOR 2SC1841-PAFAEA R133 1-247-807-31 CARBON 100 5% 1/4W
– 103 –
MAIN
R141 1-249-433-11 CARBON 22K 5% 1/4W R319 1-247-893-11 CARBON 390K 5% 1/4W
R142 1-249-433-11 CARBON 22K 5% 1/4W R321 1-249-422-11 CARBON 2.7K 5% 1/4W F
R143 1-249-417-11 CARBON 1K 5% 1/4W F
R324 1-247-876-11 CARBON 75K 5% 1/4W
R145 1-247-903-00 CARBON 1M 5% 1/4W R325 1-247-876-11 CARBON 75K 5% 1/4W
R151 1-249-417-11 CARBON 1K 5% 1/4W F R326 1-249-437-11 CARBON 47K 5% 1/4W
R153 1-249-417-11 CARBON 1K 5% 1/4W F
R329 1-249-417-11 CARBON 1K 5% 1/4W F
R164 1-249-415-11 CARBON 680 5% 1/4W F R332 1-249-415-11 CARBON 680 5% 1/4W F
R165 1-249-433-11 CARBON 22K 5% 1/4W
R334 1-249-415-11 CARBON 680 5% 1/4W F
R169 1-249-421-11 CARBON 2.2K 5% 1/4W F R337 1-249-417-11 CARBON 1K 5% 1/4W F
R170 1-249-441-11 CARBON 100K 5% 1/4W
R171 1-249-429-11 CARBON 10K 5% 1/4W R338 1-249-411-11 CARBON 330 5% 1/4W
R339 1-249-437-11 CARBON 47K 5% 1/4W
R178 1-249-421-11 CARBON 2.2K 5% 1/4W F R340 1-249-437-11 CARBON 47K 5% 1/4W
R183 1-249-425-11 CARBON 4.7K 5% 1/4W F
R184 1-249-429-11 CARBON 10K 5% 1/4W R343 1-249-417-11 CARBON 1K 5% 1/4W F
R351 1-249-435-11 CARBON 33K 5% 1/4W
R188 1-249-429-11 CARBON 10K 5% 1/4W
R356 1-249-428-11 CARBON 8.2K 5% 1/4W F
R196 1-249-417-11 CARBON 1K 5% 1/4W F R357 1-249-428-11 CARBON 8.2K 5% 1/4W F
R199 1-249-429-11 CARBON 10K 5% 1/4W
R201 1-247-888-11 CARBON 240K 5% 1/4W R391 1-249-422-11 CARBON 2.7K 5% 1/4W
R392 1-249-422-11 CARBON 2.7K 5% 1/4W
R202 1-247-903-00 CARBON 1M 5% 1/4W R393 1-249-426-11 CARBON 5.6K 5% 1/4W
R211 1-249-441-11 CARBON 100K 5% 1/4W R394 1-249-426-11 CARBON 5.6K 5% 1/4W
R251 1-247-888-11 CARBON 240K 5% 1/4W
R407 1-249-437-11 CARBON 47K 5% 1/4W
R302 1-249-421-11 CARBON 2.2K 5% 1/4W F
R303 1-247-807-31 CARBON 100 5% 1/4W ! R411 1-216-482-11 METAL OXIDE 1.8K 5% 3W F
R413 1-249-402-11 CARBON 56 5% 1/4W F
R304 1-247-807-31 CARBON 100 5% 1/4W R414 1-249-417-11 CARBON 1K 5% 1/4W F
R307 1-249-428-11 CARBON 8.2K 5% 1/4W F
R421 1-260-090-11 CARBON 180 5% 1/2W
R313 1-249-441-11 CARBON 100K 5% 1/4W
R435 1-249-435-11 CARBON 33K 5% 1/4W

MAIN
R443 1-249-417-11 CARBON 1K 5% 1/4W F R665 1-247-807-31 CARBON 100 5% 1/4W
R471 1-260-090-11 CARBON 180 5% 1/2W R666 1-247-807-31 CARBON 100 5% 1/4W
R473 1-249-402-11 CARBON 56 5% 1/4W F R668 1-247-807-31 CARBON 100 5% 1/4W

R474 1-249-417-11 CARBON 1K 5% 1/4W F R669 1-247-807-31 CARBON 100 5% 1/4W
R501 1-249-413-11 CARBON 470 5% 1/4W F R688 1-247-807-31 CARBON 100 5% 1/4W
R502 1-249-425-11 CARBON 4.7K 5% 1/4W F R689 1-247-807-31 CARBON 100 5% 1/4W
R505 1-249-429-11 CARBON 10K 5% 1/4W R801 1-249-417-11 CARBON 1K 5% 1/4W F

R522 1-249-417-11 CARBON 1K 5% 1/4W F R805 1-249-417-11 CARBON 1K 5% 1/4W F
R524 1-249-407-11 CARBON 150 5% 1/4W F R807 1-249-441-11 CARBON 100K 5% 1/4W
(E,MY,SP,HK,TW,IA) ! R808 1-220-893-11 METAL 0.22 10% 5W
R524 1-249-425-11 CARBON 4.7K 5% 1/4W F R809 1-260-076-11 CARBON 10 5% 1/2W
(EA) ! R810 1-215-872-11 METAL OXIDE 3.3K 5% 1W F
R527 1-249-429-11 CARBON 10K 5% 1/4W
R536 1-249-429-11 CARBON 10K 5% 1/4W ! R811 1-212-881-11 FUSIBLE 100 5% 1/4W F
! R812 1-202-972-61 FUSIBLE 1 5% 1/4W F
R550 1-247-843-11 CARBON 3.3K 5% 1/4W R813 1-249-435-11 CARBON 33K 5% 1/4W
R567 1-247-807-31 CARBON 100 5% 1/4W R815 1-249-433-11 CARBON 22K 5% 1/4W
R568 1-249-429-11 CARBON 10K 5% 1/4W
R817 1-249-421-11 CARBON 2.2K 5% 1/4W F
R610 1-247-891-00 CARBON 330K 5% 1/4W
R833 1-260-117-11 CARBON 33K 5% 1/2W
R627 1-247-807-31 CARBON 100 5% 1/4W
R854 1-249-438-11 CARBON 56K 5% 1/4W
R630 1-247-807-31 CARBON 100 5% 1/4W R855 1-249-417-11 CARBON 1K 5% 1/4W F
R640 1-247-807-31 CARBON 100 5% 1/4W
R642 1-247-807-31 CARBON 100 5% 1/4W ! R858 1-220-893-11 METAL 0.22 10% 5W
R859 1-260-076-11 CARBON 10 5% 1/2W
R643 1-247-807-31 CARBON 100 5% 1/4W ! R860 1-215-872-11 METAL OXIDE 3.3K 5% 1W F
R649 1-247-807-31 CARBON 100 5% 1/4W ! R861 1-212-881-11 FUSIBLE 100 5% 1/4W F
R651 1-247-807-31 CARBON 100 5% 1/4W
R892 1-249-441-11 CARBON 100K 5% 1/4W
R653 1-247-807-31 CARBON 100 5% 1/4W R901 1-247-843-11 CARBON 3.3K 5% 1/4W
R654 1-247-807-31 CARBON 100 5% 1/4W R902 1-249-415-11 CARBON 680 5% 1/4W F
R655 1-247-807-31 CARBON 100 5% 1/4W R903 1-249-419-11 CARBON 1.5K 5% 1/4W F
R659 1-247-807-31 CARBON 100 5% 1/4W
R660 1-247-807-31 CARBON 100 5% 1/4W R904 1-249-414-11 CARBON 560 5% 1/4W F
R905 1-249-425-11 CARBON 4.7K 5% 1/4W F

MAIN MOTOR (SLIDE) MOTOR (TURN) PANEL
R906 1-247-843-11 CARBON 3.3K 5% 1/4W < SWITCH >
R907 1-249-415-11 CARBON 680 5% 1/4W F
R908 1-249-429-11 CARBON 10K 5% 1/4W S801 1-762-527-11 SWITCH, ROTARY (OPEN/CLOSE)
R909 1-249-430-11 CARBON 12K 5% 1/4W **************************************************************

R911 1-249-409-11 CARBON 220 5% 1/4W F
R916 1-249-421-11 CARBON 2.2K 5% 1/4W F * 1-658-577-11 MOTOR (TURN) BOARD
R917 1-260-087-81 CARBON 100 5% 1/2W F ******************
R918 1-249-421-11 CARBON 2.2K 5% 1/4W F
< CAPACITOR >
R919 1-249-409-11 CARBON 220 5% 1/4W F
R920 1-249-383-11 CARBON 1.5 5% 1/6W F C701 1-162-306-11 CERAMIC 0.01uF 20% 16V
R921 1-249-383-11 CARBON 1.5 5% 1/6W F C702 1-126-964-11 ELECT 10uF 20% 50V
R931 1-249-429-11 CARBON 10K 5% 1/4W C705 1-162-306-11 CERAMIC 0.01uF 20% 16V
< VARIABLE RESISTOR > < CONNECTOR >
RV301 1-238-600-11 RES, ADJ, CARBON 10K CN703 1-750-413-11 CONNECTOR, FFC/FPC 8P
RV351 1-238-600-11 RES, ADJ, CARBON 10K CN704 1-506-469-11 PIN, CONNECTOR 4P
< RELAY > < DIODE >
RY401 1-755-168-11 RELAY D701 8-719-983-66 DIODE MTZJ-T-72-3.6B
< THERMISTOR > < IC >
TH831 1-807-796-11 THERMISTOR IC701 8-759-633-65 IC M54641L
< TERMINAL > < RESISTOR >
TM401 1-537-240-31 TERMINAL BOARD (CHECKER PIN)(SPEAKER) R706 1-249-411-11 CARBON 330 5% 1/4W
TM402 1-537-240-31 TERMINAL BOARD (CHECKER PIN) R707 1-249-401-11 CARBON 47 5% 1/4W F
(SURROUND SPEAKER)
**************************************************************
< VIBRATOR >
A-4419-146-A PANEL BOARD, COMPLETE
X601 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) *********************
X613 1-781-107-21 VIBRATOR, SERAMIC (16MHz)
* 4-214-439-11 HOLDER, FL TUBE
************************************************************** * 4-949-935-51 CUSHION (FL)
* 1-658-578-11 MOTOR (SLIDE) BOARD < CAPACITOR >

*******************
C601 1-124-589-11 ELECT 47uF 20% 16V
< CAPACITOR > C602 1-126-163-11 ELECT 4.7uF 20% 50V
C801 1-162-306-11 CERAMIC 0.01uF 20% 16V C604 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C804 1-162-306-11 CERAMIC 0.01uF 20% 16V C605 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C805 1-126-964-11 ELECT 10uF 20% 50V
< CONNECTOR > C608 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C610 1-124-589-11 ELECT 47uF 20% 16V
* CN801 1-568-947-11 PIN, CONNECTOR 9P C611 1-163-031-11 CERAMIC CHIP 0.01uF 50V
< DIODE >
D801 8-719-921-48 DIODE MTZJ-T-72-5.6C (Malaysia PRODUCT) C615 1-163-031-11 CERAMIC CHIP 0.01uF 50V
D801 8-719-109-89 DIODE RD5.6ESB2 (Indonesia PRODUCT) C616 1-126-157-11 ELECT 10uF 20% 16V
D804 8-719-911-19 DIODE 1SS119 C617 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
D805 8-719-911-19 DIODE 1SS119 C618 1-126-157-11 ELECT 10uF 20% 16V
< IC > C619 1-126-157-11 ELECT 10uF 20% 16V

C620 1-126-163-11 ELECT 4.7uF 20% 50V
IC801 8-759-274-09 IC BA6286N C621 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
C622 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
< RESISTOR > C625 1-126-157-11 ELECT 10uF 20% 16V
R801 1-249-401-11 CARBON 47 5% 1/4W F
– 106 –
PANEL
C626 1-163-038-91 CERAMIC CHIP 0.1uF 25V D616 8-719-057-97 DIODE SEL5923A-TP15 (VIDEO CD)
C628 1-126-163-11 ELECT 4.7uF 20% 50V D617 8-719-057-97 DIODE SEL5923A-TP15 (PBC OFF)
C629 1-124-589-11 ELECT 47uF 20% 16V
C630 1-126-157-11 ELECT 10uF 20% 16V D618 8-719-057-97 DIODE SEL5923A-TP15 (PBC)
C631 1-163-031-11 CERAMIC CHIP 0.01uF 50V D619 8-719-056-13 DIODE SML79423C-TP15 (^)
D620 8-719-073-47 DIODE SML72923C-TP15 (REC, PAUSE/START
C632 1-124-589-11 ELECT 47uF 20% 16V D621 8-719-056-13 DIODE SML79423C-TP15 (AUTO BPM)
C633 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V D622 8-719-057-97 DIODE SEL5923A-TP15 (+/))
C703 1-163-038-91 CERAMIC CHIP 0.1uF 25V D623 8-719-057-97 DIODE SEL5923A-TP15 (-/0)
C704 1-163-031-11 CERAMIC CHIP 0.01uF 50V D624 8-719-063-93 DIODE SLR325VC-N-T32 (JOG)
D625 8-719-063-93 DIODE SLR325VC-N-T32 (ENTER/ENXT)
C711 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D626 8-719-057-97 DIODE SEL5923A-TP15 (GROOVE)
C712 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V D627 8-719-057-97 DIODE SEL5923A-TP15 (PAD A)
C713 1-126-160-11 ELECT 1uF 20% 50V
C714 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V D628 8-719-057-97 DIODE SEL5923A-TP15 (PAD B)
C715 1-124-465-00 ELECT 0.47uF 20% 50V D629 8-719-057-97 DIODE SEL5923A-TP15 (BEAT ON/OFF)
D630 8-719-057-97 DIODE SEL5923A-TP15 (JAM)
C716 1-124-465-00 ELECT 0.47uF 20% 50V D631 8-719-058-03 DIODE SEL5423E-TP15 (9 (B DECK))
C717 1-164-492-11 CERAMIC CHIP 0.15uF 10% 16V D632 8-719-058-03 DIODE SEL5423E-TP15 (( (B DECK))
C719 1-126-160-11 ELECT 1uF 20% 50V D633 8-719-058-03 DIODE SEL5423E-TP15 (9 (A DECK))
C720 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V D634 8-719-058-03 DIODE SEL5423E-TP15 (( (A DECK))
D635 8-719-063-93 DIODE SLR325VC-N-T32 (TIMER SELECT)
C721 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V D701 8-719-976-99 DIODE DTZ5.1B
C723 1-124-589-11 ELECT 47uF 20% 16V < GROUND PLATE >
C725 1-124-589-11 ELECT 47uF 20% 16V EP601 1-537-770-21 TERMINAL BOARD, GROUND
C731 1-163-031-11 CERAMIC CHIP 0.01uF 50V < FERRITE BEAD >
C732 1-124-257-00 ELECT 2.2uF 20% 50V
C733 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V FB601 1-414-234-22 INDUCTOR CHIP 0UH
C734 1-163-109-00 CERAMIC CHIP 47PF 5% 50V FB602 1-414-234-22 INDUCTOR CHIP 0UH
C735 1-126-157-11 ELECT 10uF 20% 16V
< FLUORESCENT INDICATOR >
C737 1-124-463-00 ELECT 0.1uF 20% 50V FL601 1-517-831-31 INDICATOR TUBE, FLUORESCENT
C738 1-124-257-00 ELECT 2.2uF 20% 50V
C739 1-163-109-00 CERAMIC CHIP 47PF 5% 50V < IC >
IC601 8-759-589-14 IC TMP88CS76F-6005
C741 1-126-157-11 ELECT 10uF 20% 16V IC602 8-749-011-05 IC GP1U28X
C742 1-163-251-11 CERAMIC CHIP 100PF 5% 50V IC603 8-759-083-77 IC BA3830F
C743 1-124-257-00 ELECT 2.2uF 20% 50V IC604 8-759-342-19 IC NJU3716M-T2
C744 1-163-031-11 CERAMIC CHIP 0.01uF 50V IC605 8-759-577-80 IC MSM6654A-540GS-K
C745 1-124-257-00 ELECT 2.2uF 20% 50V
IC711 8-759-496-41 IC M65850FP-E1
C747 1-163-038-91 CERAMIC CHIP 0.1uF 25V IC712 8-759-636-55 IC M5218AFP
C783 1-163-031-11 CERAMIC CHIP 0.01uF 50V < JACK >
J701 1-785-569-11 JACK (SMALL TYPE)(PHONES)
< CONNECTOR > J711 1-785-569-11 JACK (SMALL TYPE)(MIC 1)
J712 1-785-569-11 JACK (SMALL TYPE)(MIC 2)
* CN601 1-568-867-11 SOCKET, CONNECTOR 25P
< JUMPER RESISTOR >
< DIODE >
JR501 1-216-296-91 SHORT 0
D601 8-719-058-24 DIODE RB501V-40TE-17 JR502 1-216-296-91 SHORT 0
D608 8-719-074-27 DIODE SELUIE10CXM-LC (LEFT) JR503 1-216-295-91 SHORT 0
D609 8-719-074-24 DIODE SELUD10CXM-LC (RIGHT) JR504 1-216-295-91 SHORT 0
D611 8-719-071-41 DIODE SELS5923C-TP15 (SYNC EQ) JR505 1-216-295-91 SHORT 0
D612 8-719-071-44 DIODE SELS5223C-TP15 (EFFECT)
JR506 1-216-295-91 SHORT 0
D613 8-719-071-41 DIODE SELS5923C-TP15 (SYNC BASS L) JR507 1-216-295-91 SHORT 0
D614 8-719-071-41 DIODE SELS5923C-TP15 (SYNC BASS H) JR508 1-216-296-91 SHORT 0
D615 8-719-063-93 DIODE SLR325VC-N-T32 (NON STOP) JR509 1-216-296-91 SHORT 0
– 107 –
PANEL
JR510 1-216-296-91 SHORT 0 R626 1-216-045-00 METAL CHIP 680 5% 1/10W
JR511 1-216-296-91 SHORT 0 R627 1-216-049-91 RES,CHIP 1K 5% 1/10W

JR512 1-216-296-91 SHORT 0 R628 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
JR516 1-216-295-91 SHORT 0 R632 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

JR518 1-216-296-91 SHORT 0 R634 1-216-073-00 METAL CHIP 10K 5% 1/10W
JR519 1-216-295-91 SHORT 0 R635 1-216-077-00 METAL CHIP 15K 5% 1/10W
R636 1-216-073-00 METAL CHIP 10K 5% 1/10W
< COIL >
R637 1-216-035-00 METAL CHIP 270 5% 1/10W
L601 1-412-029-11 INDUCTOR CHIP 10uH R638 1-216-037-00 METAL CHIP 330 5% 1/10W
L602 1-412-032-11 INDUCTOR CHIP 100uH R639 1-216-041-00 METAL CHIP 470 5% 1/10W
R640 1-216-043-91 RES,CHIP 560 5% 1/10W
< TRANSISTOR > R641 1-216-045-00 METAL CHIP 680 5% 1/10W
Q601 8-729-118-00 TRANSISTOR 2SB1116-L R642 1-216-049-91 RES,CHIP 1K 5% 1/10W

Q602 8-729-118-00 TRANSISTOR 2SB1116-L R643 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
Q603 8-729-119-78 TRANSISTOR 2SC403SP-51 R644 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
Q604 8-729-119-76 TRANSISTOR 2SA1175-HFE R645 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
Q605 8-729-119-78 TRANSISTOR 2SC403SP-51 R646 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
Q607 8-729-900-36 TRANSISTOR DTC124ES R647 1-216-065-91 RES,CHIP 4.7K 5% 1/10W

Q608 8-729-900-36 TRANSISTOR DTC124ES R648 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
Q610 8-729-900-74 TRANSISTOR DTC143TS R649 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q611 8-729-900-74 TRANSISTOR DTC143TS R650 1-216-035-00 METAL CHIP 270 5% 1/10W
Q614 8-729-900-74 TRANSISTOR DTC143TS R653 1-216-043-91 RES,CHIP 560 5% 1/10W
Q616 8-729-900-74 TRANSISTOR DTC143TS R655 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q620 8-729-119-76 TRANSISTOR 2SA1175-HFE R656 1-216-035-00 METAL CHIP 270 5% 1/10W
< RESISTOR > R657 1-216-037-00 METAL CHIP 330 5% 1/10W

R658 1-216-041-00 METAL CHIP 470 5% 1/10W
R601 1-216-025-91 RES,CHIP 100 5% 1/10W R659 1-216-043-91 RES,CHIP 560 5% 1/10W
R602 1-216-073-00 METAL CHIP 10K 5% 1/10W R660 1-216-045-00 METAL CHIP 680 5% 1/10W
R603 1-216-025-91 RES,CHIP 100 5% 1/10W R661 1-216-049-91 RES,CHIP 1K 5% 1/10W
R604 1-216-025-91 RES,CHIP 100 5% 1/10W
R605 1-216-073-00 METAL CHIP 10K 5% 1/10W R662 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R663 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R606 1-216-017-91 RES,CHIP 47 5% 1/10W R664 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R608 1-216-111-00 METAL CHIP 390K 5% 1/10W R666 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R609 1-216-097-91 RES,CHIP 100K 5% 1/10W
R668 1-216-073-00 METAL CHIP 10K 5% 1/10W
R611 1-216-097-91 RES,CHIP 100K 5% 1/10W R669 1-216-077-00 METAL CHIP 15K 5% 1/10W
R612 1-216-017-91 RES,CHIP 47 5% 1/10W R670 1-216-083-00 METAL CHIP 27K 5% 1/10W
R613 1-216-085-00 METAL CHIP 33K 5% 1/10W R671 1-216-091-00 METAL CHIP 56K 5% 1/10W
R614 1-216-113-00 METAL CHIP 470K 5% 1/10W
R616 1-216-121-91 RES,CHIP 1M 5% 1/10W R672 1-216-049-91 RES,CHIP 1K 5% 1/10W
R673 1-216-089-91 RES,CHIP 47K 5% 1/10W
R617 1-216-097-91 RES,CHIP 100K 5% 1/10W R674 1-216-049-91 RES,CHIP 1K 5% 1/10W
R619 1-216-043-91 RES,CHIP 560 5% 1/10W R676 1-216-089-91 RES,CHIP 47K 5% 1/10W
R620 1-216-073-00 METAL CHIP 10K 5% 1/10W
R621 1-216-073-00 METAL CHIP 10K 5% 1/10W R677 1-216-089-91 RES,CHIP 47K 5% 1/10W
R678 1-216-073-00 METAL CHIP 10K 5% 1/10W
R622 1-216-035-00 METAL CHIP 270 5% 1/10W R680 1-216-073-00 METAL CHIP 10K 5% 1/10W
R625 1-216-043-91 RES,CHIP 560 5% 1/10W
– 108 –
PANEL
R686 1-216-097-91 RES,CHIP 100K 5% 1/10W
R687 1-216-097-91 RES,CHIP 100K 5% 1/10W R776 1-216-019-00 METAL CHIP 56 5% 1/10W
R777 1-216-025-91 RES,CHIP 100 5% 1/10W
R688 1-216-073-00 METAL CHIP 10K 5% 1/10W R778 1-216-025-91 RES,CHIP 100 5% 1/10W
R689 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R780 1-216-073-00 METAL CHIP 10K 5% 1/10W
R692 1-216-097-91 RES,CHIP 100K 5% 1/10W
R783 1-216-073-00 METAL CHIP 10K 5% 1/10W
R696 1-216-097-91 RES,CHIP 100K 5% 1/10W R786 1-216-049-91 RES,CHIP 1K 5% 1/10W
R697 1-216-097-91 RES,CHIP 100K 5% 1/10W
R788 1-216-085-00 RES,CHIP 33K 5% 1/10W
R701 1-216-017-91 RES,CHIP 47 5% 1/10W R790 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R711 1-216-081-00 METAL CHIP 22K 5% 1/10W
R712 1-216-081-00 METAL CHIP 22K 5% 1/10W < VARIABLE RESISTOR >
R713 1-216-081-00 METAL CHIP 22K 5% 1/10W
RV711 1-225-739-11 RES, VAR 50K (ECHO LEVEL)
R714 1-216-089-91 RES,CHIP 47K 5% 1/10W RV712 1-225-739-11 RES, VAR 50K (MIC-VOL)
R715 1-216-081-00 METAL CHIP 22K 5% 1/10W
R716 1-216-077-00 METAL CHIP 15K 5% 1/10W < SWITCH >
R717 1-216-081-00 METAL CHIP 22K 5% 1/10W
R718 1-216-081-00 METAL CHIP 22K 5% 1/10W S601 1-473-534-11 ENCODER, ROTARY (JOG/0 x ))
S602 1-473-392-11 ENCODER, ROTARY (VOLUME)
R719 1-216-099-00 METAL CHIP 120K 5% 1/10W S611 1-762-875-21 SWITCH, KEYBOARD (SYNC BASE)
R721 1-216-073-00 METAL CHIP 10K 5% 1/10W S612 1-762-875-21 SWITCH, KEYBOARD (SYNC EQ)
R722 1-216-049-91 RES,CHIP 1K 5% 1/10W S613 1-762-875-21 SWITCH, KEYBOARD (KARAOKE PON/MIX)
R723 1-216-097-91 RES,CHIP 100K 5% 1/10W
R724 1-216-049-91 RES,CHIP 1K 5% 1/10W S614 1-762-875-21 SWITCH, KEYBOARD (CD NON STOP)
S615 1-762-875-21 SWITCH, KEYBOARD (SURROUND)
R726 1-216-073-00 METAL CHIP 10K 5% 1/10W S616 1-762-875-21 SWITCH, KEYBOARD (DBFB)
R727 1-216-077-00 METAL CHIP 15K 5% 1/10W S617 1-762-875-21 SWITCH, KEYBOARD (ENTER/NEXT)
R728 1-216-103-00 METAL CHIP 180K 5% 1/10W S618 1-762-875-21 SWITCH, KEYBOARD (-/0)
R729 1-216-025-91 RES,CHIP 100 5% 1/10W
R731 1-216-049-91 RES,CHIP 1K 5% 1/10W S619 1-762-875-21 SWITCH, KEYBOARD (+/))
S620 1-762-875-21 SWITCH, KEYBOARD (GROOVE)
R732 1-216-073-00 METAL CHIP 10K 5% 1/10W S621 1-762-875-21 SWITCH, KEYBOARD (PAD B)
R751 1-216-029-00 METAL CHIP 150 5% 1/10W S622 1-762-875-21 SWITCH, KEYBOARD (BEAT SPEED)
R752 1-216-029-00 METAL CHIP 150 5% 1/10W S623 1-762-875-21 SWITCH, KEYBOARD (BEAT SEC)
R753 1-216-029-00 METAL CHIP 150 5% 1/10W
R754 1-216-029-00 METAL CHIP 150 5% 1/10W S624 1-762-875-21 SWITCH, KEYBOARD (BEAT ON/OFF)
S625 1-762-875-21 SWITCH, KEYBOARD (REC, PUASE/START)
R755 1-216-029-00 METAL CHIP 150 5% 1/10W S626 1-762-875-21 SWITCH, KEYBOARD (HI DUB)
R756 1-216-029-00 METAL CHIP 150 5% 1/10W S627 1-762-875-21 SWITCH, KEYBOARD (CD SYNC)
R757 1-216-029-00 METAL CHIP 150 5% 1/10W S628 1-762-875-21 SWITCH, KEYBOARD (PAD A)
R758 1-216-022-00 METAL CHIP 75 5% 1/10W
R759 1-216-022-00 METAL CHIP 75 5% 1/10W S629 1-762-875-21 SWITCH, KEYBOARD (BEAT MIX)
S630 1-762-875-21 SWITCH, KEYBOARD (BEAT JAM)
R760 1-216-022-00 METAL CHIP 75 5% 1/10W S631 1-762-875-21 SWITCH, KEYBOARD (BEAT LEVEL)
R761 1-216-022-00 METAL CHIP 75 5% 1/10W S632 1-762-875-21 SWITCH, KEYBOARD (SELECT)
R762 1-216-029-00 METAL CHIP 150 5% 1/10W S633 1-762-875-21 SWITCH, KEYBOARD (RETURN)
R763 1-216-029-00 METAL CHIP 150 5% 1/10W
R764 1-216-019-00 METAL CHIP 56 5% 1/10W S634 1-762-875-21 SWITCH, KEYBOARD (PREY)
S635 1-762-875-21 SWITCH, KEYBOARD (NEXT)
R765 1-216-019-00 METAL CHIP 56 5% 1/10W S636 1-762-875-21 SWITCH, KEYBOARD (AUTO BPM)
R766 1-216-029-00 METAL CHIP 150 5% 1/10W S637 1-762-875-21 SWITCH, KEYBOARD (CD FLASH)
R767 1-216-022-00 METAL CHIP 75 5% 1/10W S638 1-762-875-21 SWITCH, KEYBOARD (P FILE MEMORY)
R768 1-216-029-00 METAL CHIP 150 5% 1/10W
R769 1-216-029-00 METAL CHIP 150 5% 1/10W S639 1-762-875-21 SWITCH, KEYBOARD (GEQ CONTROL)
S640 1-762-875-21 SWITCH, KEYBOARD (FILE SELECT)
R770 1-216-029-00 METAL CHIP 150 5% 1/10W S641 1-762-875-21 SWITCH, KEYBOARD (EFFECT)
R771 1-216-029-00 METAL CHIP 150 5% 1/10W S642 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)
– 109 –
PANEL SENSOR SURROUND TRANS
S643 1-762-875-21 SWITCH, KEYBOARD (^) < CONNECTOR >
S644 1-762-875-21 SWITCH, KEYBOARD (p) CN1201 1-564-788-11 PIN, CONNECTOR 8P

S645 1-762-875-21 SWITCH, KEYBOARD (B:()
S646 1-762-875-21 SWITCH, KEYBOARD (B:9) < IC >
S647 1-762-875-21 SWITCH, KEYBOARD (A:()
S648 1-762-875-21 SWITCH, KEYBOARD (A:9) IC1201 8-759-579-61 IC LV1150
S649 1-762-875-21 SWITCH, KEYBOARD (FUNCTION) < COIL >

S650 1-762-875-21 SWITCH, KEYBOARD (CD LOOP)
S651 1-762-875-21 SWITCH, KEYBOARD (DISPLAY) L1201 1-410-509-11 INDUCTOR 10uH
S652 1-762-875-21 SWITCH, KEYBOARD (CLOCK/TIME SET)
S653 1-762-875-21 SWITCH, KEYBOARD (TIME SELECT) < RESISTOR >
S654 1-762-875-21 SWITCH, KEYBOARD (SPECTRUM ANALYZER) R1201 1-247-807-31 CARBON 100 5% 1/4W
S655 1-762-875-21 SWITCH, KEYBOARD (REPEAT STERO/MONO) R1203 1-249-441-11 CARBON 100K 5% 1/4W
S656 1-762-875-21 SWITCH, KEYBOARD (PLAY MODE DOLBY ON) R1204 1-249-441-11 CARBON 100K 5% 1/4W
S657 1-762-875-21 SWITCH, KEYBOARD R1205 1-249-417-11 CARBON 1K 5% 1/4W F
(EDIT DIRECTION TUNER MEMORY) R1206 1-249-441-11 CARBON 100K 5% 1/4W
< VIBRATOR > R1207 1-249-441-11 CARBON 100K 5% 1/4W
X601 1-781-312-11 VIBRATOR, CERAMIC (12.5MHz) **************************************************************

X602 1-767-353-11 VIBRATOR, CERAMIC (4.09MHz)
* 1-672-474-11 TRANS BOARD
************************************************************** ***********
* 1-658-576-11 SENSOR BOARD < CAPACITOR >

************
C971 1-128-563-11 ELECT 100uF 20% 100V
< IC > C972 1-126-960-11 ELECT 1uF 20% 50V
C973 1-126-947-11 ELECT 47uF 20% 35V
IC702 8-749-924-18 IC PHOTO INTERRUPTER RPI-1391
IC703 8-749-924-30 IC PHOTO REFLECTOR GP2S28 < CONNECTOR >
************************************************************** * CN901 1-564-527-11 PLUG, CONNECTOR 12P

CN902 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE)3P
A-4419-159-A SURROUND BOARD, COMPLETE CN951 1-564-321-00 PIN, CONNECTOR 2P
************************
< DIODE >
< CAPACITOR >
D971 8-719-024-99 DIODE 11ES2-NTA2B
C1201 1-162-203-31 CERAMIC 15PF 5% 50V D972 8-719-056-97 DIODE UDZ-TE-17-27B
C1202 1-162-216-31 CERAMIC 51PF 5% 50V D973 8-719-056-74 DIODE UDZ-TE-17-3.0B
C1203 1-162-282-31 CERAMIC 100PF 10% 50V
C1204 1-162-283-31 CERAMIC 120PF 10% 50V < FUSE >
C1205 1-162-279-31 CERAMIC 75PF 10% 50V
! F951 1-532-506-31 FUSE (T6.3AL/250V)(EXCEPT TH)
C1206 1-136-165-00 FILM 0.1uF 5% 50V ! F952 1-532-465-31 FUSE (T3.15AL/250V)(EXCEPT TH)
C1207 1-162-306-11 CERAMIC 0.01uF 20% 16V ! F953 1-532-465-31 FUSE (T3.15AL/250V)
C1208 1-126-934-11 ELECT 220uF 20% 10V ! F961 1-532-505-31 FUSE (T5AL/250V)
C1209 1-136-165-00 FILM 0.1uF 5% 50V ! F962 1-532-505-31 FUSE (T5AL/250V)
C1210 1-126-964-11 ELECT 10uF 20% 50V
< FUSE HOLDER >
C1211 1-126-964-11 ELECT 10uF 20% 50V
C1212 1-162-306-11 CERAMIC 0.01uF 20% 16V FH951 1-533-233-21 HOLDER, FUSE
C1213 1-126-934-11 ELECT 220uF 20% 10V FH952 1-533-233-21 HOLDER, FUSE
C1214 1-136-167-00 FILM 0.15uF 5% 50V FH953 1-533-233-21 HOLDER, FUSE
C1215 1-162-303-11 CERAMIC 0.0033uF 30% 16V FH954 1-533-233-21 HOLDER, FUSE
FH955 1-533-233-21 HOLDER, FUSE
C1216 1-136-167-00 FILM 0.15uF 5% 50V
C1217 1-124-252-00 ELECT 0.33uF 20% 50V FH956 1-533-233-21 HOLDER, FUSE
FH964 1-533-233-21 HOLDER, FUSE
C1221 1-162-216-31 CERAMIC 51PF 5% 50V
– 110 –
TRANS VIDEO
< TRANSISTOR > C413 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
Q971 8-729-048-52 TRANSISTOR 2SA1932(TP) C452 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< RESISTOR > C502 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
! R951 1-219-120-11 FUSIBLE 0.15 5% 1/4W F C504 1-165-319-11 CERAMIC CHIP 0.1uF 50V
! R952 1-219-120-11 FUSIBLE 0.15 5% 1/4W F
! R953 1-219-120-11 FUSIBLE 0.15 5% 1/4W F C505 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
! R971 1-216-455-11 METAL OXIDE 560 5% 2W F C506 1-165-319-11 CERAMIC CHIP 0.1uF 50V
R972 1-216-085-00 METAL CHIP 33K 5% 1/10W C507 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
R973 1-216-073-00 METAL CHIP 10K 5% 1/10W C510 1-165-319-11 CERAMIC CHIP 0.1uF 50V
R974 1-216-025-91 RES,CHIP 100 5% 1/10W
R975 1-216-025-91 RES,CHIP 100 5% 1/10W C531 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C536 1-126-193-11 ELECT 1uF 20% 50V
< SWITCH > C537 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
! S951 1-771-291-11 SWITCH, POWER (VOLTAGE SELECTOR) C539 1-165-319-11 CERAMIC CHIP 0.1uF 50V
(EXCEPT VX8:TH) C540 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
< TRANSFORMER > C542 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C543 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
************************************************************** C545 1-165-319-11 CERAMIC CHIP 0.1uF 50V
A-4724-727-A VIDEO BOARD, COMPLETE C547 1-126-193-11 ELECT 1uF 20% 50V
********************* C548 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< CAPACITOR > C549 1-165-319-11 CERAMIC CHIP 0.1uF 50V

C101 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C551 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C102 1-163-143-00 CERAMIC CHIP 0.0012uF 5% 50V C552 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C103 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C553 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C104 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C201 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C555 1-124-779-00 ELECT CHIP 10uF 20% 16V
C202 1-163-143-00 CERAMIC CHIP 0.0012uF 5% 50V C559 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C203 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C560 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C301 1-163-127-00 CERAMIC CHIP 270PF 5% 50V C561 1-163-233-11 CERAMIC CHIP 18PF 5% 50V
C303 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C562 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C304 1-163-235-11 CERAMIC CHIP 22PF 5% 50V C564 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C305 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C565 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C306 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C566 1-165-319-11 CERAMIC CHIP 0.1uF 50V
C311 1-216-295-91 SHORT 0 C568 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C569 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C313 1-165-319-11 CERAMIC CHIP 0.1uF 50V C570 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
C314 1-165-319-11 CERAMIC CHIP 0.1uF 50V C571 1-128-065-11 ELECT CHIP 68MF 20% 10V
C318 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C573 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C401 1-165-319-11 CERAMIC CHIP 0.1uF 50V C574 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C402 1-124-778-00 ELECT CHIP 22uF 20% 6.3V C577 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C403 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C404 1-126-206-11 ELECT CHIP 100uF 20% 6.3V < CONNECTOR >
C405 1-110-530-11 ELECT CHIP 1000uF 20% 6.3V
C406 1-110-530-11 ELECT CHIP 1000uF 20% 6.3V CN501 1-770-706-11 CONNECTOR, FFC/FPC 23P
CN503 1-779-416-11 CONNECTOR,FFC(LIF(NON-ZIF))13P
C409 1-124-778-00 ELECT CHIP 22uF 20% 6.3V
C410 1-165-319-11 CERAMIC CHIP 0.1uF 50V < TRIMMER >
C412 1-165-319-11 CERAMIC CHIP 0.1uF 50V CT503 1-141-539-11 CAP, ADJ 10PF

VIDEO
< DIODE > Q307 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
Q308 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
D301 8-719-054-23 DIODE RB706D-40-T146 Q310 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
D501 8-719-422-12 DIODE MA8039 Q453 8-729-920-72 TRANSISTOR 2SA1037K-T-146-QR
D502 8-719-018-51 DIODE CL-170R-CD Q454 8-729-920-72 TRANSISTOR 2SA1037K-T-146-QR
< IC > Q502 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L

Q531 8-729-140-75 TRANSISTOR 2SD999-CLCK
IC101 8-759-701-39 IC NJM3404AM
IC401 8-759-262-00 IC MC14576CF < RESISTOR >
IC501 8-759-269-92 IC SN74HCU04ANS-E20
IC502 8-759-587-67 IC M30620MC-A05FP R101 1-216-073-00 METAL CHIP 10K 5% 1/10W
IC504 8-759-269-92 IC SN74HCU04ANS-E20 R102 1-208-441-61 RES,CHIP 1.5K 2% 1/10W
R103 1-208-441-61 RES,CHIP 1.5K 2% 1/10W
IC505 8-759-535-48 IC CL680T-D1 R105 1-216-295-91 SHORT 0
IC506 8-759-573-23 IC LC372100PM-J48-TLA R201 1-216-073-00 METAL CHIP 10K 5% 1/10W
IC507 8-759-342-01 IC MB814260-70PJER
IC509 8-759-535-62 IC PCM1727E-2/T2 R202 1-208-441-61 RES,CHIP 1.5K 2% 1/10W
R203 1-208-441-61 RES,CHIP 1.5K 2% 1/10W
< JACK > R205 1-216-295-91 SHORT 0
R301 1-216-624-11 METAL CHIP 75 0.5% 1/10W
J301 1-537-943-11 TERMINAL, S (S VIDEO OUT) R302 1-216-624-11 METAL CHIP 75 0.5% 1/10W
J302 1-774-227-11 JACK, PIN 1P (VIDEO OUT)
R305 1-216-049-91 RES,CHIP 1K 5% 1/10W
< JUMPER RESISTOR > R306 1-216-073-00 METAL CHIP 10K 5% 1/10W
R307 1-216-049-91 RES,CHIP 1K 5% 1/10W
JW101 1-216-295-91 SHORT 0 R308 1-216-049-91 RES,CHIP 1K 5% 1/10W
JW201 1-216-295-91 SHORT 0 R309 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
JW401 1-216-295-91 SHORT 0
JW402 1-216-295-91 SHORT 0 R312 1-216-073-00 METAL CHIP 10K 5% 1/10W
R314 1-216-049-91 RES,CHIP 1K 5% 1/10W
JW404 1-216-295-91 SHORT 0 R315 1-216-047-91 RES,CHIP 820 5% 1/10W
JW405 1-216-295-91 SHORT 0 R316 1-216-657-11 METAL CHIP 1.8K 0.5% 1/10W
JW413 1-216-295-91 SHORT 0
JW421 1-216-295-91 SHORT 0 R317 1-216-683-11 METAL CHIP 22K 0.5% 1/10W
JW422 1-216-295-91 SHORT 0 R318 1-216-033-00 METAL CHIP 220 5% 1/10W
R319 1-216-049-91 RES,CHIP 1K 5% 1/10W
JW502 1-216-295-91 SHORT 0 R320 1-216-651-11 METAL CHIP 1K 0.5% 1/10W
JW504 1-216-295-91 SHORT 0
JW505 1-216-295-91 SHORT 0 R324 1-216-022-00 METAL CHIP 75 5% 1/10W
R325 1-216-295-91 SHORT 0
< COIL > R327 1-216-049-91 RES,CHIP 1K 5% 1/10W
R328 1-216-655-11 METAL CHIP 1.5K 0.5% 1/10W
L301 1-410-372-21 INDUCTOR CHIP 1.8uH R329 1-216-649-11 METAL CHIP 820 0.5% 1/10W
L302 1-410-372-21 INDUCTOR CHIP 1.8uH
L501 1-216-296-91 SHORT 0 R332 1-216-651-11 METAL CHIP 1K 0.5% 1/10W
L502 1-216-296-91 SHORT 0 R333 1-216-046-00 METAL CHIP 750 5% 1/10W
L503 1-216-296-91 SHORT 0 R335 1-216-073-00 METAL CHIP 10K 5% 1/10W
R336 1-216-073-00 METAL CHIP 10K 5% 1/10W
L504 1-410-375-11 INDUCTOR CHIP 3.3uH R340 1-216-022-00 METAL CHIP 75 5% 1/10W
L505 1-216-296-91 SHORT 0
L506 1-216-296-91 SHORT 0 R341 1-216-121-91 RES,CHIP 1M 5% 1/10W
L507 1-216-296-91 SHORT 0 R342 1-216-022-00 METAL CHIP 75 5% 1/10W
L508 1-216-296-91 SHORT 0 R403 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R404 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
L509 1-216-296-91 SHORT 0 R405 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
L510 1-216-296-91 SHORT 0
R406 1-216-081-00 METAL CHIP 22K 5% 1/10W
< TRANSISTOR > R407 1-216-073-00 METAL CHIP 10K 5% 1/10W
R408 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q301 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R409 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q302 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R410 1-216-049-91 RES,CHIP 1K 5% 1/10W
Q303 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L
Q304 8-729-024-91 TRANSISTOR 2SC2712-GL-TE85L R411 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q306 8-729-027-44 TRANSISTOR DTC114TKA-T146 R412 1-216-073-00 METAL CHIP 10K 5% 1/10W
R414 1-216-081-00 METAL CHIP 22K 5% 1/10W
– 112 –
VIDEO
R415 1-216-081-00 METAL CHIP 22K 5% 1/10W R559 1-216-073-00 METAL CHIP 10K 5% 1/10W
R561 1-216-049-91 RES,CHIP 1K 5% 1/10W
R426 1-216-073-00 METAL CHIP 10K 5% 1/10W
R566 1-216-025-91 RES,CHIP 100 5% 1/10W
R462 1-216-025-91 RES,CHIP 100 5% 1/10W
R573 1-216-073-00 METAL CHIP 10K 5% 1/10W
R503 1-216-025-91 RES,CHIP 100 5% 1/10W
R580 1-216-073-00 METAL CHIP 10K 5% 1/10W
R506 1-216-025-91 RES,CHIP 100 5% 1/10W
R507 1-216-073-00 METAL CHIP 10K 5% 1/10W < SWITCH >
R508 1-216-081-00 METAL CHIP 22K 5% 1/10W
R509 1-216-081-00 METAL CHIP 22K 5% 1/10W S501 1-571-395-11 SWITCH, SLIDE (SYSTEM SELECTOR)
R510 1-216-081-00 METAL CHIP 22K 5% 1/10W
< VIBRATOR >
R511 1-216-081-00 METAL CHIP 22K 5% 1/10W
R512 1-216-081-00 METAL CHIP 22K 5% 1/10W X501 1-767-510-11 VIBRATOR, CERAMIC (10MHz)
R513 1-216-081-00 METAL CHIP 22K 5% 1/10W X503 1-767-519-11 VIBRATOR, CRYSTAL (27MHz)
R514 1-216-081-00 METAL CHIP 22K 5% 1/10W
R516 1-216-073-00 METAL CHIP 10K 5% 1/10W **************************************************************
R517 1-216-073-00 METAL CHIP 10K 5% 1/10W MISCELLANEOUS

R518 1-216-073-00 METAL CHIP 10K 5% 1/10W *************
R519 1-216-025-91 RES,CHIP 100 5% 1/10W
R520 1-216-057-00 METAL CHIP 2.2K 5% 1/10W 5 1-233-545-11 TUNER UNIT (TH)
R523 1-216-013-00 METAL CHIP 33 5% 1/10W 5 1-233-546-13 ENCAPSULATED COMPONENT (EXCEPT TH)
9 1-790-927-11 WIRE (FLAT TYPE) (13 CORE)
R530 1-216-081-00 METAL CHIP 22K 5% 1/10W 10 1-775-212-11 WIRE (FLAT TYPE) (23 CORE)
R531 1-216-025-91 RES,CHIP 100 5% 1/10W 55 1-769-977-11 WIRE (FLAT TYPE)(13 CORE) (TH)
R532 1-216-025-91 RES,CHIP 100 5% 1/10W
R533 1-216-025-91 RES,CHIP 100 5% 1/10W 55 1-773-009-11 WIRE (FLAT TYPE)(15 CORE) (150mm)
R534 1-216-073-00 METAL CHIP 10K 5% 1/10W (EXCEPT TH)
56 1-773-024-11 WIRE (FLAT TYPE)(15 CORE) (320mm)
R535 1-216-073-00 METAL CHIP 10K 5% 1/10W 58 1-569-007-11 ADAPTOR, CONVERSION 2P (E,IA)
R536 1-216-033-00 METAL CHIP 220 5% 1/10W 58 1-569-008-21 ADAPTOR, CONVERSION 2P (EA,SP,MY,TW)
R537 1-216-025-91 RES,CHIP 100 5% 1/10W 58 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
R538 1-216-073-00 METAL CHIP 10K 5% 1/10W
R542 1-216-049-91 RES,CHIP 1K 5% 1/10W ! 59 1-575-651-11 CORD, POWER (EA,SP,HK,MY,TW)
! 59 1-575-653-11 CORD, POWER (E,IA,TH)
R543 1-216-685-11 METAL CHIP 27K 0.5% 1/10W 60 1-773-042-11 WIRE (FLAT TYPE)(17 CORE)
R544 1-216-659-11 METAL CHIP 2.2K 0.5% 1/10W 116 1-773-223-11 WIRE (FLAT TYPE)(25 CORE)
R545 1-216-025-91 RES,CHIP 100 5% 1/10W 122 1-675-195-11 PUSH CATCH STOPPER (A)
R546 1-216-049-91 RES,CHIP 1K 5% 1/10W
R547 1-216-295-91 SHORT 0 124 1-675-196-11 PUSH CATCH STOPPER (B)
257 1-452-925-21 MAGNET ASSY
R548 1-216-049-91 RES,CHIP 1K 5% 1/10W 258 1-776-042-11 WIRE (FLAT TYPE) (8 CORE)
R549 1-216-025-91 RES,CHIP 100 5% 1/10W ! 301 8-820-020-02 OPTICAL PICK-UP KSS-213D/Q-NP
R550 1-216-025-91 RES,CHIP 100 5% 1/10W 302 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
R551 1-216-025-91 RES,CHIP 100 5% 1/10W
R552 1-216-025-91 RES,CHIP 100 5% 1/10W FL601 1-517-831-31 INDICATOR TUBE, FLUORESCENT
HP101 A-2056-681-B DECK (A) ASSY, HEAD (230AWR2)
R554 1-216-025-91 RES,CHIP 100 5% 1/10W HP101 A-2056-683-B DECK (A) ASSY, HEAD (230PWR2)
R555 1-216-121-91 RES,CHIP 1M 5% 1/10W HRPE101 A-2056-682-B DECK (B) ASSY, HEAD (230AWR2)
R556 1-216-025-91 RES,CHIP 100 5% 1/10W HRPE101 A-2056-684-B DECK (B) ASSY, HEAD (230PWR2)
R557 1-216-025-91 RES,CHIP 100 5% 1/10W
R558 1-216-073-00 METAL CHIP 10K 5% 1/10W M1 A-2004-628-A MOTOR ASSY, CAPSTAN

HCD-VX8/VX8J
Ref. No. Part No. Description Remark

M101 X-4917-523-4 MOTOR ASSY (SPINDLE)
M102 X-4917-504-1 MOTOR ASSY (SLED)
M701 A-4672-004-A MOTOR ASSY (TURN)
M801 A-4672-004-A MOTOR ASSY (SLIDE)
M901 1-763-072-11 FAN, D.C.

S811 1-473-335-11 ENCODER, ROTARY
**************************************************************
*************
HARDWARE LIST
*************
#1 7-685-871-01 SCREW +BVTT 3X6 (S)

#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
#3 7-685-880-09 SCREW +BVTT 4X6 (S)
#4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
#5 7-685-852-04 SCREW +BVTT 2X5 (S)
#7 7-682-553-04 SCREW +P 3X20

#8 7-685-851-04 SCREW +BVTT 2X4 (S)
#9 7-628-254-15 SCREW +PS 2.6X6
#10 7-628-254-50 SCREW +PS 2.6X16
#11 7-685-861-01 SCREW +BVTT 2.6X5 (S)
#13 7-685-880-09 SCREW +BVTP 3X10 TYPE2 N-S
Sony Corporation 99E097024-1

Printed in Singapore © 1999. 5
9-928-836-11 Home A&V Products Company Published by Quality Assurance Dept.
– 114 – (Shinagawa)

Sony VX

Uploaded by

Copyright:

Available Formats

Sony VX

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony VX

Uploaded by

Copyright:

Available Formats

HCD-VX8/VX8J

SERVICE MANUAL E Model

HCD-VX8/VX8J is the tuner, deck, CD and

Model Name Using Similar Mechanism HCD-GRX80/RXD8/RXD8S

— Continued on next page —

COMPACT DISC DECK RECEIVER

PARTS No. MODEL PRODUCT

Flexible Circuit Board Repairing

1. SERVICING NOTE .......................................................... 4 9. EXPLODED VIEWS

5. TEST MODE ..................................................................... 12

6. MECHANICAL ADJUSTMENTS .......................... 13

7. ELECTRICAL ADJUSTMENTS ............................... 13

1 Remove the Case.

3 Pull-out the disc tray.

2 Turn the cam to the direction

NOTE FOR INSTALLATION (ROTARY ENCODER)

Note:When attaching the Base unit, Insert the

Note:When attaching the BU cam,

Downloaded from www.Manualslib.com manuals search engine

3-1. LOADING PANEL

1 Turn the cam to the direction

3-2. FRONT PANEL AND VIDEO BOARD

6 Screw (BVTP 3x10)

1 Screw (BVTT 3x6)

3 Screw (BVTT 3x6)

4 Cassette holder (L)

Note for installation

3-4. CD SW BOARD AND PANEL BOARD

3 CD SW board 1 Three screws

8 Flat type wire

7 Nut !¡ Five screws

3 Flat type wire (8 core)

2 Pull-out the disc tray.

1 Turn the cam the

Sled Servo Mode

Change-over of AM Tuner Step between 9kHz and 10kHz

[VIDEO BOARD] (SIDE B)

Waveform of oscilloscope 1. Insert the WS-48B into deck B.

Playback Level Adjustment (Deck A, Deck B)

Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301

4. Mode: Playback 4. Mode: Playback

recorded level meter recorded level meter

Adjustment Location: AUDIO board Adjustment Location: MAIN board

Adjustment Location: [MAIN BOARD] (Conductor Side)

Adjustment Location: BD board

RF Level Check Traverse waveform

Tracking servo Tracking servo

1. Connect the frequency counter to check point of the VIDEO

[ VIDEO BOARD ] – SIDE A – [ VIDEO BOARD ] – SIDE B –

MOTOR (TURN) board

MOTOR (SLIDE) board

8-2. BLOCK DIAGRAMS

LD IC104 (XTAL 33.8MHz)

M701 IN1 8 DISC

Downloaded from www.Manualslib.com manuals search engine

– VIDEO SECTION – D-RAM ROM

BUFFER TRAP J302

Downloaded from www.Manualslib.com manuals search engine

RV311 MAIN SECTION