Clarion Co., Ltd. Published by Service Dept.

5-35-2, Hakusan, Bunkyouku, Tokyo, 112-8608 Japan 298-5960-00 Dec.2001 P

Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: 048-443-1111 FAX:048-433-6996 Printed in Japan

Service Manual
6 Disc CD Changer with CD text

 

Model 
(PE-2433B/for U.S.A.)
6 - DI SC CD CHA NGE R
OP T I CA L DI GI T A L OUT P UT

TEXT
(PE-2433K/for Other Countries)

Model 
(PE-2433E/for Europe)

■ SPECIFICATIONS ■ COMPONENTS
Frequency response: 5Hz to 20kHz(±1dB) PE-2433B-A/K-A/E-A
Signal to noise ratio:
105dB(1kHz)IHF-A Main unit −−−−− 1
Wow and flutter: Below measurement limits CD magazine CAA-397-900 1
Power supply voltage:14.4V DC Mounting bracket 300-9873-20 2
(10.8 to 15.6V allowable) Mounting bracket(with bolt) 300-9874-20 2
Ground: Negative Lock pin 335-0594-20 3
Current consumption: 1A Extension lead(13P) 855-3416-50 1
Dimensions(mm): 225(W)×63(H)×167(D) Parts bag −−−−−
Weight: 1.65kg Cushion rubber 345-8653-00 2
Parts bag −−−−−
■ NOTES Cord clamp 335-0833-01 2
Wing nut 722-0545-00 4
※ Use a CeNET extension cable that is less than 20m in
Hex-bolt 734-5008-37 4
length.
※ CD singles cannot be used.
※ This unit is compatible with CD text.When it is connected ■ To engineers in charge of repair or
to a center unit suitable for CD text display, CD text can
be displayed.(When it is connected to a center unit with- inspection of our products.
out CD text function,CD text cannot be displayed.)
Before repair or inspection, make sure to follow
※ The following magazines cannot be used for this
unit.Using them will result in a damage to hte mecha-
the instructions so that customers and Engineers
nism and cause the magazine not to eject. in charge of repair or inspection can avoid suf-
1.Magazine(CAA-122) for the 12-disc CD chnager fering any risk or injury.
2.Magazine(CAA-355) for the 6-disc CD changer 1. Use specified parts.
※ Do not play heart-shaped, octagonal, or other specially The system uses parts with special safety features against
shaped CDs. fire and voltage. Use only parts with equivalent charac-
※ We cannot supply PWB with component parts in prin- teristics when replacing them.
ciple. When a circuit on PWB has failure , please repair The use of unspecified parts shall be regarded as re-
it by component parts base. Parts which are not men- modeling for which we shall not be liable. The onus of
tioned in service manual are not supplied. product liability (PL) shall not be our responsibility in cases
※ Specifications and design are subject to change without where an accident or failure is as a result of unspecified
notice for further improvement. parts being used.
2. Place the parts and wiring back in their original positions
after replacement or re-wiring.
For proper circuit construction, use of insulation tubes,
bonding, gaps to PWB, etc, is involved. The wiring con-

-1- DCZ625
DCZ628
 nection and routing to the PWB are specially planned enter through the ventilation slots in the cover.
using clamps to keep away from heated and high voltage 9-3. Cleaning the lens
parts. Ensure that they are placed back in their original Dust on the optical lens affects performance. To
positions after repair or inspection. clean the lens, apply a small amount of
If extended damage is caused due to negligence during isopropyl alcohol to lens paper and wipe the lens
repair, the legal responsibility shall be with the repairing gently.
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se- ■CAUTIONS
curely in their original position after repair. Ensure for Use of controls,adjustment or performance of procedures
safety reasons there is no possibility of secondary other than those specified herein,may result in hazardous
ploblems around the repaired spots. radiation exposure.
If extended damage is caused due to negligence of re- The COMPACT DISC player and MINI DISC player should
pair, the legal responsibility shall be with the repairing not be adjusted or repaired by anyone except properly quali-
company. fied service personnel.
4. Caution in removal and making wiring connection to the This appliance contains a laser system and is classified as
parts for the automobile. a "CLASS 1 LASER PRODUCT".To use this model
Disconnect the battery terminal after turning the ignition properly,read this Owner's Manual carefully and kep this
key off. If wrong wiring connections are made with the manual for your future reference.In case of any trouble with
battery connected, a short circuit and/or fire may occur. this player,please contact your nearest"AUTHORIZED ser-
If extensive damage is caused due to negligence of re- vice station".To prevent direct exposure to the laser beam,do
pair, the legal responsibility shall be with the repairing not to open the enclosure.
company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality
is observed in their appearance. Always replace them
with new ones. (The chip parts include resistors, capaci-
tors, diodes, transistors, etc). The negative pole of tanta-
lum capacitors is highly susceptible to heat, so use spe-
cial care when replacing them and check the operation
afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the X

iron tip temperature is around 270℃. Take care not to

apply the iron tip repeatedly(more than three times)to the
same patterns. Also take care not to apply the tip with
force.
7. Turn the unit OFF during disassembly and parts replace-
ment. Recheck all work before you apply power to the
unit.
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the
laser optical diode lights up, keep your eyes more than
30cms away from the lens. Prolonged viewing of the la-
ser within 30cms may damage your eyesight.
9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes
or body, or discharge static electricity before handling the
optical pickup.
9-1. Laser diode
The laser diode terminals are shorted for transpor-
tation in order to prevent electrostatic damage.
After replacement, open the shorted circuit. When
removing the pickup from the mechanism, short
the terminals by soldering them to prevent this
damage.
9-2. Actuator
The actuator has a powerful magnetic circuit. If a
magnetic material is put close to it. Its characteris-
tics will change. Ensure that no foreign substances

DCZ625 -2-
DCZ628
 pin 20: ADDRESS : IN : The address input for the CD auto chang-
■ HOW TO CHANGE THE ADDRESS er.
pin 21: WRITE : IN : The write command input.
SWITCH pin 22: RX : IN : Serial data input of IE BUS.
When connecting an CD changer and MD changer by Ce- pin 23: TX : O : Serial data output of IE BUS.

NET,no more than 2 units can be connected.When both of pin 24: NU : - : Not in use.
pin 25: NU : - : Not in use.
them are CD,the address switch needs to be reset so that
pin 26: NU : - : Not in use.
the address switch number is not the same for each. pin 27: NU : - : Not in use.
pin 28: NU : - : Not in use.
How to change the address switch pin 29: NU : - : Not in use.
Switch the address by using a plastic stick with a sharp pin 30: NU : - : Not in use.
tip or equivalent. pin 31: NU : - : Not in use.
pin 32: NU : - : Not in use.
pin 33: NU : - : Not in use.
pin 34: NU : - : Not in use.
pin 35: NU : - : Not in use.
pin 36: DATUM : IN : The datum point signal input for counting
the disk number.
pin 37: D No TR : IN : Disk number detect pulse input.
pin 38: NU : - : Not in use.
pin 39: CE : IN : Chip enable signal input.
pin 40: NU : - : Not in use.
pin 41: PW ON INV : O : The inverted signal of "POWER ON 1(pin
1)".
pin 42: POWER ON 2 : O : The power ON signal output to the power
supply section.
pin 43: NU : - : Not in use.
pin 44: LIMIT : IN : Limiting switch signal input.
pin 45: HOLD IN : IN : "L"= The magazine is charged.
pin 46: LOAD END : O : The loading end signal output.
pin 47: 8cm/12cm : IN : 8cm/12cm
pin 48: UD CW : O : Up/down motor control signal output.
Caution pin 49: UD CCW : O : Up/down motor control signal output.
・ The unit may not operate when both CD changers are pin 50: LD CW : O : Loading motor control signal output.
set to the same address switch number. pin 51: LD CCW : O : Loading motor control signal output.
pin 52: NU : - : Not in use.
・ Never change the address switch during operation.Doing
pin 53: T CLK : O : "Test mode display" clock output.
sp can cause malfunction or breakdown.Do not change
pin 54: T DATA : O : The serial data output for the test mode
the address switch forcibly,because this may also cause indication.
malfunction. pin 55: T CLR : O : The clear signal output for the test mode
indication.
・ The Ce-NET cable wiring must be less than
pin 56: NU : - : Not in use.
20m(65.62ft)in length. pin 57: NU : - : Not in use.
・ Be sure that the CD changer numbers are not the same. pin 58: NU : - : Not in use.
・ Do not use the address switch numbers "3" and "4" for pin 59: DR MUTE : O : The muting pulse output to the CD driver.
the MD changer. pin 60: GV SW : O : The reset pulse output to the digital servo
IC.
pin 61: RST : IN : Reset signal input.
pin 62: CCE : O : Chip enable signal output to CD IC.
■ EXPLANATION OF IC pin 63: BUC CLOCK : O : CD IC clock pulse output.
pin 64: BUS 3 :I/O: CD IC Data input / output.
052-5046-01 M30621M8A-F27GP CD Auto Changer Control
pin 65: BUS 2 :I/O: CD IC Data input / output.
1.Terminal Description pin 66: BUS 1 :I/O: CD IC Data input / output.
pin 1: POWER ON 1 : O : The power ON signal output to the power pin 67: BUS 0 :I/O: CD IC Data input / output.
supply section. pin 68: NU : - : Not in use.
pin 2: SB SYNC : IN : Sub code data sync. pin 69: NU : - : Not in use.
pin 3: A MUTE : O : Audio mute signal output. pin 70: NU : - : Not in use.
pin 4: CD AC FLAG : O : The CD auto changer active flag output. pin 71: EJECT : IN : Eject signal input.
pin 5: NU : - : Not in use. pin 72: TEST 4 : IN : For the test.
pin 6: CN VSS : IN : Inputting "L" at single mode operation. pin 73: TEST 3 : IN : For the test.
pin 7: NU : - : Not in use. pin 74: TEST 2 : IN : For the test.
pin 8: NU : - : Not in use. pin 75: A VSS : - : Analog ground.
pin 9: RESET : IN : Reset signal input. pin 76: TEST 1 : IN : For the test.
pin 10: X OUT : O : Crystal connection. pin 77: Vref : - : Reference voltage
pin 11: VSS : - : Negative supply voltage. pin 78: A VCC : - : Positive supply voltage for the internal an-
pin 12: X IN : IN : Crystal connection. alog section.
pin 13: VDD : - : Positive supply voltage. pin 79: NU : - : Not in use.
pin 14: NMI : IN : Connect to VDD. pin 80: D STOP : O : Digital output control. Outputs "H" at Play.
pin 15: B/U DET : IN : Backup voltage ON signal input.
pin 16: SYS ACC : IN : ACC detect signal input.
pin 17: MAG SW : IN : The inserted flag input for the magazine.
pin 18: CONNECT : IN : IE-BUS input.
pin 19: NU : - : Not in use.

-3- DCZ625
DCZ628
DCZ628
DCZ625
CONNECTOR
MAIN PWB
FPC
14P CONNECTOR
J4
DRIVE UNIT
D-OUT
D-OUT P301
RF AMP
IC1 DSP & DAC
TA2157F IC5 MUTE LPF B.T.L. ANALOG SW L +/-
■ BLOCK DIAGRAM

TC94A14FA Q4,5 IC9 IC11 IC12

PICK UP 2SD1306 NJM4558 NJM4558 74VHC4066 R +/-

13P DIN
J301
SPINDLE
MOTOR DRIVE FPC SERVO DRIVER
IC2 ADRS
BD7961
SLED BUS DRIVER BUS+/BUS-
MOTOR LIMIT SW IC6
MAIN CONTROLLER CA0008 ADDRESS SW
3.3V IC7 S301
REG M30621M8A
SYS-ACC
LOADING FPC MOTOR 5V ACC-DET
DRIVER REG

-4-
B/U 12V
LOADING MOTOR

VDD REF
RESET B/U DET VDD 5V
LOAD-END SW 5V
IC8 IC10
S-80721 S-80843
POWER 5V

HOLDER-IN SW MEMO-VDD

12/8 DISC SENSOR

CD 9V
IC4
BA09ST
DISC NO. TR
EJECT SW MAGAZINE SW POSITION SW
IC3
S2 S3 S1
GP1S94
UP/DOWN MOTOR
■ EXPLODED VIEW・PARTS LIST
Main section

B6
17
6 8
12
13
5 B4
14 B4 3
4 B5
B2

B3 B3
B6 12

B1
21 A4
B5 10 1

A3 12
19
15
16

11

A4

12 20
A2
18
A3

2-1 14
A1

12 B2

B1

A2

7 12
22 A1
2

Note)Some parts depend on each model.The model name is specified in the description.
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 −−−−− CHANGER MECHANISM 1 11 750-3459-21 FL-SPRING R 1
(025020)
12 716-1716-00 SCREW 11
2 940-7965-63 ESCUTCHEON ASSY(DCZ625) 1
940-7965-60 ESCUTCHEON ASSY(DCZ628) 1 13 716-0484-00 SPECIAL SCREW 1
2-1 716-0872-00 PAD SCREW 1 14 629-0080-00 DAMPER GS-6 4
3 013-3968-00 SWITCH 1 15 371-5693-22 TRIM PLATE 1
4 039-1948-20 CONNECTOR PWB 1 16 382-6254-20 BUTTON 1
(WITHOUT COMPONENT)
17 620-1088-20 CE-NET HOLDER 1
5 074-1194-00 OUTLET SOCKET 1
18 620-0996-21 DAMPER PLATE R 1
6 075-0305-00 JACK 1
19 620-0997-20 DAMPER PLATE F 1
7 286-9860-00 SETPLATE(DCZ625/U.S.A) 1
286-9858-00 SETPLATE(DCZ628) 20 622-1545-20 FL PIN R 1
286-9861-00 SETPLATE(DCZ625/OTHER)
21 622-1546-20 FL PIN L 1
8 310-1742-21 UPPER CASE 1
22 348-0331-00 TAPE 1
9 311-1838-20 LOWER CASE 1
10 750-3460-21 FL-SPRING L 1

-5- DCZ625
DCZ628
Changer mechanism section

55
B3 10
B3
55
55
36

A7 B2
B2
A4
B10 62
62
A6 55 55 B7 B6
B1 B1
B7 B6 A5
B5 B8
A3
C1 55
B5
B10
67 B4
A2
33 C2 B9

71 C3 B4
D2 30
19
44
12 34
32
D1

B8
A10 31
55 N1
A11 B9
A14 E1

67
E
A1
A7 12 1
2
3
55
4
5
6

A10
A6 A14 A4
A13
A12 A9 62
9
A5
A3 55
A8
E
1
2
3
A2 8
4
5
6
A9
51 A1
A13
65 45 57
65
69 N1 68
A8
12
54
A12
57

C1 57 16

11 A11
59
63
D2

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 966-0582-22 DRIVE-P-ASSY 1 12 966-0594-24 V-CHASSIS ASSY 1
2 966-0583-20 DISC HOLD ASSY 1 13 966-0454-00 SH-RACK-ASSY 1
3 966-0584-23 CLAMP-P-ASSY F 1 14 966-0623-23 L-LOWER-P-ASSY 1
4 966-0585-22 CAM GEAR ASSY 1 15 969-0061-30 PICK UP-ASSY 1
5 966-0586-22 MOTOR-P-ASSY 1 16 039-1947-20 MAIN PWB 1
(WITHOUT COMPONENT)
6 966-0588-21 HOLDER-L-ASSY 1
17 001-0563-00 LED 1
7 966-0589-23 L-UPPER-P-ASSY 1
18 013-7413-50 DETECTOR SWITCH 3
8 966-0590-20 MG-LO-P-ASSY 1
19 SMA-180-100 MOTOR ASSY(UP/DOWN) 1
9 966-0591-21 REAR PANEL ASSY 1
20 SMA-181-100 MOTOR ASSY(SLED) 1
10 966-0592-20 UP-PLATE ASSY 1
21 SMA-179-100 MOTOR ASSY(SPINDLE) 1
11 966-0593-20 UD-GEAR-P-ASSY 1

DCZ625 -6-
DCZ628
 35
29
O1
65
65 4 F2

F1

66 O1 70 H1
K2
G2
G1 C2
28
G1
7 C3
26 H2 46
I1 F2
2 F1
I1 N2 M1 M2

47 55
52 6
J1
F4 H1
G2
D1
F5 41
K2
60
3
55
60 57
18 E1 65
L1
24 65 49 1
17 K3 P1 43
K1 57 20 50
48 27 61
72
57 J2
38
N1 42
J4 N2 57 21
N1
F4
J4 L1
Q1
61 58
23 K1 37
64 55 65 13
55 H2 M2 57 39
63 J1
F5 25
J2
J3
55 M1 56 15
5 40
P1
55 K3
55
14 Q1
J3
53
55 22
57
18

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
22 039-1949-20 DRIVE PWB 1 38 801-4912-60 VINYL-COAT-WIRE(BRN) 1
(WITHOUT COMPONENT)
39 621-0589-20 SECOND GEAR 1
23 039-1950-20 LOADING PWB 1
(WITHOUT COMPONENT) 40 621-0590-20 LS GEAR 1
24 060-0252-01 PHOTO-TR 1 41 621-0591-20 PICK UP GUIDE 1
25 620-0999-21 LS-SPRING 1 42 621-0592-21 LS-HOLDER 1
26 620-1575-21 SWITCH PLATE 1 43 621-0593-20 LS GUIDE 1
27 620-1007-22 CLAMP PLATE M 1 44 802-4906-60 VINYL-COAT-WIRE(RED) 1
28 620-1008-24 CLAMP PLATE R 1 45 621-0597-20 V-GEAR A 1
29 620-1009-21 CLAMPER PLATE 1 46 621-0630-22 HOLDER-G-RAIL R 1
30 620-1016-20 GAP PLATE R 1 47 621-0631-21 HOLDER-G-RAIL L 1
31 620-1017-20 GAP PLATE F 1 48 621-0703-20 L-GEAR A 1
32 620-1018-20 MG EJECT PLATE 1 49 621-0633-20 L-GEAR B 1
33 620-1019-20 SLIDE PLATE R 1 50 805-4912-60 VINYL-COAT-WIRE(GRN) 1
34 620-1020-20 SLIDE PLATE F 1 51 621-0635-20 V-HELICAL GEAR 1
35 620-1031-21 LOADING ARM 1 52 621-0636-21 CLAMPER RING 1
36 620-1034-23 SIDE PANEL 1 53 624-3022-00 LEAD SCREW 1
37 621-0587-21 SCREW HOLD BASE 1 54 629-0061-00 GEAR DAMPER 1

-7- DCZ625
DCZ628
 NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
55 716-0484-00 SCREW(M2×2.5) 23 64 745-0789-01 DRIVE WASHER 1
56 716-0675-00 SCREW(M2×5.5) 1 65 746-0761-00 WASHER 7
57 716-1716-00 SCREW(M2×3) 10 66 750-3461-21 DISC-H-SPRING 1
58 716-3469-00 SCREW 2 67 750-3462-20 GAP SPRING 2
59 735-2006-11 D-SEMS-SCREW(M2×6) 1 68 750-3463-20 MG LOCK SPRING 1
60 739-1722-17 SCREW(M1.7×2.2) 2 69 750-3464-20 MG EJECT SPRING 1
61 739-2022-17 SCREW(M2×2.2) 2 70 750-3492-22 CLAMPER SPRING 1
62 743-1500-10 E-RING 3 71 800-4906-60 VINYL-COAT-WIRE(BLK) 1
63 743-2000-10 E-RING 2 72 SMA-188-100 MOTOR ASSY(LOADING) 1

■ ELECTRICAL PARTS LIST

Note) Several different parts of the same reference number are alternative parts.
Main PWB(B1) section One of those parts is used in the set.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C1 178-1052-78 16V1uF C62 183-1073-17 6.3V100uF Q12 125-2004-92 RN1402
C2 043-0533-50 0.047uF C64 046-1032-78 0.01uF R1 033-1041-15 1/16W 100kΩ
C3 042-0426-31 6.3V100uF C65 045-2201-50 22pF R2 033-1041-15 1/16W 100kΩ
C4 183-1073-17 6.3V100uF C66 045-2201-50 22pF R3 033-1041-15 1/16W 100kΩ
C5 046-6822-58 6800pF C67 183-2263-37 16V22uF R4 033-1041-15 1/16W 100kΩ
C6 178-1052-78 16V1uF C69 183-2263-37 16V22uF R5 033-1041-15 1/16W 100kΩ
C7 168-1042-78 16V0.1uF C70 184-4773-31 16V470uF R6 033-1041-15 1/16W 100kΩ
C8 183-3363-27 10V33uF C71 046-1032-78 0.01uF R7 033-2211-15 1/16W 220Ω
C9 183-3363-27 10V33uF C74 183-1073-17 6.3V100uF R8 111-2711-98 1/16W 270Ω
C10 168-1042-78 16V0.1uF C75 183-2263-37 16V22uF R9 033-6831-15 1/16W 68kΩ
C11 168-1042-78 16V0.1uF C76 183-2263-37 16V22uF R10 111-2201-98 1/4WS 22Ω
C12 045-5096-50 5pF C77 183-2263-37 16V22uF R11 111-2201-98 1/4WS 22Ω
C13 183-3363-27 10V33uF C78 183-2263-37 16V22uF R12 119-1031-15 1/16W 10kΩ
C14 178-1052-78 16V1uF C79 183-2263-37 16V22uF R13 119-2231-15 1/16W 22kΩ
C16 168-1032-55 0.01uF C80 183-2263-37 16V22uF R14 033-8211-15 1/16W 820Ω
C17 045-5601-50 56pF C81 178-3342-78 0.33uF R15 111-1001-98 1/4WS 10Ω
C18 045-1011-50 100pF D1 001-0516-90 MA111 R16 119-1031-15 1/16W 10kΩ
C19 168-1032-55 0.01uF D2 001-1305-90 DAN217U R17 119-1531-15 1/16W 15kΩ
C20 043-0533-50 0.047uF D3 001-1304-90 DAN202U R18 033-6831-15 1/16W 68kΩ
C21 046-1532-78 0.015uF D4 001-0466-90 S5688B R19 033-2721-15 1/16W 2.7kΩ
C22 045-4701-50 47pF D5 001-0466-90 S5688B R20 033-1011-15 1/16W 100Ω
C23 043-0533-50 0.047uF D6 001-0516-90 MA111 R21 033-1021-15 1/16W 1kΩ
C24 046-1522-58 1500pF D7 001-0504-35 HZS6C2L R22 033-1031-15 1/16W 10kΩ
C25 046-4722-58 4700pF D8 001-0516-90 MA111 R23 033-1831-15 1/16W 18kΩ
C26 046-1032-78 0.01uF IC1 051-5710-90 TA2157F R24 033-1531-15 1/16W 15kΩ
C27 043-0533-50 0.047uF IC2 051-6060-08 BD7961FM R25 033-1031-15 1/16W 10kΩ
C28 046-3332-78 0.033uF IC3 051-5806-00 GP1S94 R26 033-4731-15 1/16W 47kΩ
C29 046-3332-78 0.033uF IC4 051-3289-00 BA09ST R27 033-1041-15 1/16W 100kΩ
C30 046-4712-58 470pF IC5 051-6376-00 TC94A14FA R28 033-5621-15 1/16W 5.6kΩ
C31 045-4701-50 47pF IC6 051-6600-38 CA0008AM R29 033-1041-15 1/16W 100kΩ
C33 043-0533-50 0.047uF IC7 052-5046-01 M30621M8A-F27GP R31 111-2711-98 1/16W 270Ω
C34 043-0533-50 0.047uF IC8 051-5407-08 S-80721AN R32 033-1041-15 1/16W 100kΩ
C36 042-0452-81 10V220uF IC9 051-0350-93 NJM4558M R33 033-3331-15 1/16W 33kΩ
C37 168-1042-78 16V0.1uF IC10 051-5434-08 S-80843ALNP-EA7 R34 033-1051-15 1/16W 1MΩ
C38 168-1042-78 16V0.1uF IC11 051-0350-93 NJM4558M R35 033-4711-15 1/16W 470Ω
C39 166-1801-50 18pF IC12 051-7232-08 74VHC4066M R36 119-2211-15 1/16W 220Ω
C40 166-1801-50 18pF J1 074-1138-65 15P R37 033-3321-15 1/16W 3.3kΩ
C41 168-1032-55 0.01uF J2 074-1158-56 6P R38 119-4731-15 1/16W 47kΩ
C42 168-1042-78 16V0.1uF J3 074-1158-58 8P R39 033-4731-15 1/16W 47kΩ
C43 183-3363-27 10V33uF J4 074-1158-64 14P R40 033-1041-15 1/16W 100kΩ
C44 168-1032-55 0.01uF L1 010-3050-93 10uH R41 033-4731-15 1/16W 47kΩ
C45 168-1032-55 0.01uF L2 010-2285-57 BLM21B102 R42 033-4731-15 1/16W 47kΩ
C47 166-1011-50 100pF L3 010-2285-57 BLM21B102 R43 033-1011-15 1/16W 100Ω
C48 183-3363-27 10V33uF L4 010-2285-57 BLM21B102 R44 033-1011-15 1/16W 100Ω
C49 183-1063-37 16V10uF L5 010-2285-57 BLM21B102 R45 033-1031-15 1/16W 10kΩ
C50 183-1063-37 16V10uF Q1 191-1237-50 2SB1237 R46 033-1031-15 1/16W 10kΩ
C51 042-0576-00 5.5V0.1F Q2 191-1237-50 2SB1237 R47 033-5621-15 1/16W 5.6kΩ
C52 183-1063-37 16V10uF Q3 191-1237-50 2SB1237 R48 033-1031-15 1/16W 10kΩ
C53 183-1063-37 16V10uF Q4 193-1306-00 2SD1306 R49 033-4731-15 1/16W 47kΩ
C54 183-1063-37 16V10uF Q5 193-1306-00 2SD1306 R50 033-4711-15 1/16W 470Ω
C55 043-0533-50 0.047uF Q6 125-2004-92 RN1402 R51 033-1041-15 1/16W 100kΩ
C56 046-1032-78 0.01uF Q7 190-1048-50 2SA1048 R52 119-1041-15 1/16W 100kΩ
C58 046-1032-78 0.01uF Q8 125-2004-92 RN1402 R53 033-1531-15 1/16W 15kΩ
C59 183-1063-37 16V10uF Q9 125-0014-92 DTA114 R54 033-1531-15 1/16W 15kΩ
C60 045-6801-50 68pF Q10 190-1162-00 2SA1162 R55 033-2231-15 1/16W 22kΩ
C61 045-6801-50 68pF Q11 193-1858-50 2SD1858 R56 033-1021-15 1/16W 1kΩ

DCZ625 -8-
DCZ628
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
R57 033-4731-15 1/16W 47kΩ R67 033-1031-15 1/16W 10kΩ R77 119-1011-15 1/16W 100Ω
R58 033-2731-15 1/16W 27kΩ R68 033-1031-15 1/16W 10kΩ R78 119-1011-15 1/16W 100Ω
R59 033-2731-15 1/16W 27kΩ R69 033-8221-15 1/16W 8.2kΩ R79 033-4721-15 1/16W 4.7kΩ
R60 033-1031-15 1/16W 10kΩ R70 119-1041-15 1/16W 100kΩ R80 033-2211-15 1/16W 220Ω
R61 033-1031-15 1/16W 10kΩ R71 119-1041-15 1/16W 100kΩ S1 013-7404-50 00110676
R62 033-1031-15 1/16W 10kΩ R72 119-1041-15 1/16W 100kΩ S2 013-6100-10 SKHLLD
R63 033-1031-15 1/16W 10kΩ R73 119-1041-15 1/16W 100kΩ S3 013-7404-50 00110676
R64 033-1021-15 1/16W 1kΩ R74 033-1031-15 1/16W 10kΩ T1 009-0679-00 E1-19
R65 033-1531-15 1/16W 15kΩ R75 119-1011-15 1/16W 100Ω X1 061-3038-00 16.9344MHz
R66 033-4731-15 1/16W 47kΩ R76 119-1011-15 1/16W 100Ω X2 060-1505-50 CSTCC10MG

Connector PWB(B2) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
J301 074-1194-00 13P P301 075-0305-00 DIGITAL OUT S301 013-3968-00 SSSS2

Loading PWB(B3) section

REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
D501 001-0563-00 GL380 S501 013-7413-50 SPVG12
Q501 060-0252-01 PT4850F S502 013-7413-50 SPVG12

Drive PWB(B4) section

REF No. PART No. DESCRIPTION
S503 013-7413-50 SPVG12

-9- DCZ625
DCZ628
CIRCUIT DIAGRAM /
Main PWB(B1)/Connector PWB(B2)/Loading PWB(B3)/Drive PWB(B4) section

1 G ND
2 B AC K UP
3 L -C H (+)
4 NC
5 NC
6 B U S (+)
7 R -C H (+)
8 R -C H (-)
9 S Y S AC C
10 B U S (-)
11 L -C H (-)
12 NC
13 NC

- 10 - DCZ625
DCZ628
■ PRINTED WIRING BOARD / プリント基板図
Main PWB(B1)/Connector PWB(B2)/Loading PWB(B3)/Drive PWB(B4) section

SPINDLE MOTOR
1 GND
2 BACK UP
3 L-CH(+)
4 NC
RED
BLK

5 NC
6 BUS(+)
7 R-CH(+)
8 R-CH(-)
9 SYS ACC
S 503
10 BUS(-)
11 L-CH(-)
12 NC
13 NC
BRN
GRN

SLED MOTOR

S 502

S 501

Q501

LOADING MOTOR

D501

- 11 - DCZ625
DCZ628