@AIRBUS

AIRBUS S.A.S.
Customer Services
Technical Data Support and Services
31707 Blagnac Cedex
FRANCE

FAPE3

COMPONENT MAINTENANCE MANUAL

WITH
ILLUSTRATED PART LIST

CARGO LINING

PN : ATA255000SA320

Issue: Oct 01/20 25-50-00 Rev: Oct 01/20

 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

HIGHLIGHTS

Revision No. 0 - Oct 01/20

LOCATIONS CHG DESCRIPTIONS OF CHANGE

CODE
LIST OF SERVICE BULLETINS N SBLIST REVISED

INTRODUCTION N PAGEBLOCK ADDED

TASK 25-50-00-871-802-A01 N

DESCRIPTION AND OPERATION N PAGEBLOCK ADDED

TASK 25-50-00-870-801-A01 N

REPAIR N PAGEBLOCK ADDED

TASK 25-50-00-300-801-A01 N
Subtask 25-50-00-300-004-A01 N SUBTASK ADDED
Subtask 25-50-00-300-001-A01 N SUBTASK ADDED
FIGURE 25-50-00-991-004-A01 N ILLUSTRATION ADDED

HIGHLIGHTS
Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

LIST OF EFFECTIVE CONTENT

Revision No. 0 - Oct 01/20

CONTENT CHG LAST REVISION

CODE DATE
INTRODUCTION
TASK 25-50-00-871-802-A01 N Oct 01/20

DESCRIPTION AND OPERATION

TASK 25-50-00-870-801-A01 N Oct 01/20

REPAIR
TASK 25-50-00-300-801-A01 N Oct 01/20
Subtask 25-50-00-300-004-A01 N Oct 01/20
Subtask 25-50-00-300-001-A01 N Oct 01/20
FIGURE 25-50-00-991-004-A01 N Oct 01/20

ILLUSTRATED PARTS LIST

L.E.C.
Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

TABLE OF CONTENTS

INTRODUCTION
25-50-00-871-802-A01 Introduction

DESCRIPTION AND OPERATION

25-50-00-870-801-A01 Description and Operation of Cargo Linings.

REPAIR
25-50-00-300-801-A01 Replacement of Cargo Lining

T.O.C.
Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

LIST OF SERVICE BULLETINS

SB No REV No MOD No INCORP. TITLE

DATE
*** NO SB ***

SBL
Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

INTRODUCTION

**For PN’s ALL

TASK 25-50-00-871-802-A01
Introduction
1. General
A. This CMM is only applicable to Cargo Linings.
B. Important information.
This CMM does not use component Part Numbers (PNs) to show applicable tasks and
procedures for Cargo Lining PNs.
You must use the Cargo Lining category to identify the materials and to find the applicable
repair information for Cargo Linings.
The part number PN ATA255000SA320 shown in this CMM is not an Airbus component PN, it
is used for administration only.
2. This CMM gives the operator the necessary data for identification, inspection and repair using locally
made Cargo Linings for replacement of components which are damaged in service.
The operator can use this data to:
- Know if repair by locally made Cargo Linings is possible
- Find the applicable material to locally make Cargo Linings.
3. How to use the Manual
- Refer to the questionnaire (See Task 51-12-00-300-801-A-01) to help you make sure that the
manual is applicable to your component
- Use the instructions in this manual for all the component maintenance
- Read all the applicable WARNINGS and CAUTIONS before you do the work on the Cargo
Linings.

INTRO
Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

DESCRIPTION AND OPERATION

**For PN’s ALL

TASK 25-50-00-870-801-A01
Description and Operation of Cargo Linings.
1. Cargo Linings
A. The lower deck of the aircraft has two cargo holds (the FWD cargo hold and the AFT cargo
hold). These two cargo holds are divided to make three, under floor cargo compartments.
The AFT lower deck has 2 compartments, the AFT cargo compartment and the AFT bulk
cargo compartment.
A net divides these AFT compartments.
All of these compartments contain a Cargo Lining.
B. The Cargo Lining has the following function:
- to seal the cargo hold around its support structure
- to keep smoke, flames or extinguishing agents out of all other compartments
- to prevent damage to equipment, pipes, electrical wires that are behind it
- to make sure a pressure compensation is kept between the cabin and the cargo holds
- to be resistant to handling loads.
2. Category of Cargo Lining
A. There are various categories of Cargo Lining, as shown in the list below, see also Tables 1-2 at
Task 25-50-00-300-801-A.
- E-glass (electric grade fibre glass), sandwich panel
- H-profile
- laminated lining panel
- S-glass (high strength fibre glass), sandwich panel
- decompression panel E-glass
- decompression panel S-glass, ceiling
- decompression panel S-glass, sidewall and partition
- sidewall, ceiling, decompression blow-in/blow-out panel, partition, door lining.
3. Limits and restrictions
A. Important information, the cargo linings with a rapid decompression function (installed on
Aircraft post MOD 155973) cannot be made locally.
B. For Cargo Lining replacement restrictions see Tables 1-2 at Task 25-50-00-300-801-A.

Page 1
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

REPAIR

**For PN’s ALL

TASK 25-50-00-300-801-A01
Replacement of Cargo Lining
1. Reason for the Job

WARNING : BE CAREFUL WHEN YOU USE THE CONSUMABLE MATERIAL(S). YOU MUST
OBEY THE OPERATOR’S AND MANUFACTURER’S HEALTH AND SAFETY
INSTRUCTIONS. THE CONSUMABLE MATERIAL(S) CAN CAUSE INJURY OR
DEATH TO PERSONS.

CAUTION : USE ONLY THE SPECIFIED CLEANING AGENTS. CLEANING AGENTS WHICH
ARE NOT SPECIFIED CAN CAUSE DAMAGE.
This procedure gives a repair by locally making a new Cargo Lining to replace components which are
damaged in service.
2. Job Setup

Subtask 25-50-00-300-004-A01
A. Limits and Restrictions
(1) Important information, the cargo linings with a rapid decompression function cannot be
made locally (See Fig. 25-50-00-004).
(2) Airbus permits you to locally make cargo linings, decompression panels , ACT-heat shield
panel (referred to in the text as ’Panels’) using these conditions and limits:
- The locally made Panel is a necessary solution for Aircraft On Ground (”AOG”), when
no applicable repairs are possible.
- If spare components are not available from Airbus, its licensees or other approved
sources, in a lead time that is shorter or equal to, the time which the airline can get
such Airbus parts, and on condition that the airline must not sell such Airbus parts.
- To locally make the Panels, you must only use the approved materials shown in Tables
1 to 2 of this task procedure.
- Locally made Panels (made by the operator or its maintenance provider) must only be
used by an operator for their Aircraft.
- An operator or maintenance provider can locally make Panels, but only for the
operators’ aircraft.
- The locally made Panels must obey the regulations and procedures of the operator’s
local Airworthiness Authority.
- The locally made Panels must only use a part number given by the operator. Use of an
Airbus Part Number (P/N) for locally made Panels is not permitted.
- The authority to locally make the Panels is not a guarantee or an approval of these
Panels.

Page 6001
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

- The authority to locally manufacture the Panels is an agreement that the operator
must indemnify and hold harmless Airbus, its directors, officers, employees, agents and
representatives from and against all claims, including legal fees and court costs, as a
result of the use of the locally made Panels, by the operator.
- If one or more of the above is not fulfilled, Airbus can withdraw authorization and
reserves all rights related to the Panels.

NOTE : When you use a replacement material to make a cargo lining, make sure that the
weight stays at the correct weight limit. See the applicable AIM for weight data.
3. Procedure

Subtask 25-50-00-300-001-A01
A. Replacement of Cargo Lining
(1) This procedure is for a replacement of a cargo lining and related components, when
damage is more than the Allowable Damage Limits for applicable repairs. See AMM
25-50-00-08.
Use this CMM chapter and the documents that follow, to locally make cargo lining,
decompression panels and ACT-heat shield:
- Airbus technical documentation (IPC, Definition/Installation drawings and AMM
procedures)
- Airline Instruction Manual - AIM (one per semi-finished material supplier, available
from the supplier: The Gill Corporation AIM 2001, Hutchinson Les Stratifies AIM
3455) for the manufacturing procedures of cargo lining, decompression panels and
ACT-heat shield
- Definition / Installation drawings, to find the definition of a finished part (dimensions,
location of inserts, holes, etc)
- IPC and the AMM procedures, to find the location removal and installation of the part.
(2) Refer to the list of component categories shown in the Airline Instruction Manual (AIM), to
make sure that your component can be replaced.
(3) Chose the correct material for the applicable cargo lining category.
There are various categories of cargo lining. Thus, it is important to correctly identify them
to select the applicable material so that you can make a replacement locally.
The cargo lining categories are shown in Tables 1-2 below, see also Fig 1.
For correct identification of the cargo lining category, you must find :
- The lining location in the cargo hold (FR24A, FR28, FR34, FR35, FR35.5, FR47,
FR47.2,FR52A, FR55A, FR56, FR59, FR65.)
- The lining type (sidewall, ceiling, decompression blow-in/blow-out panel, partition,
door lining)
- The lining generation : E Glass (electric grade fibre glass) or S Glass (high strength
fibre glass).

Page 6002
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

(4) Refer to the instructions for semi-finished material, shown in the applicable Airline
Instruction Manual (AIM) and install the replacement component.
Manufacturer Manufacturer
The Gill Hutchinson- Les
Corporation Stratifies
AIM 2001 AIM 3455
aftermarket.strativer@hut
info@thegillcorp.com
Cargo Lining OEM Panel Location Restriction Alternative Alternative
Category Thickness Semi-Finished Semi-Finished
Material Materia
Sandwich Panel 7.5 mm For Cargo no Gillfab 4422-295 Stratitex H2550-
0.295 in Loading/ A-001
Occasional Bulk
Configuration:
Ceiling Lining
FWD and AFT
Decompression
Panel Ceiling
FWD/ AFT
Sandwich Panel 7.8 mm For STD Bulk no Gillfab 4422-307 Stratitex H2550-
0.307 in /STD Bulk & B-001
CLS
Configuration:
Ceiling Lining
FWD/ AFT/
BULK CC
Decompression
Panel Ceiling
FWD/ AFT/
BULK CC

Page 6003
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

Sandwich Panel 9.3 mm For Cargo no Gillfab 4422-366 Stratitex H2550-

0.366 in Loading/ D-001
Occasional Bulk
Configuration:
Sidewall Lining
FWD and AFT
Decompression
Panel Sidewall
Lining FWD/
AFT
Partition Wall
FR34/ FR35.5/
FR47/ FR47.2

Page 6004
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

Sandwich Panel 9.8 mm For STD Bulk no Gillfab 4422-386 Stratitex H2550-
(0.386 in.) /STD Bulk & E-001
CLS
Configuration:
Sidewall Lining
FWD/ AFT/
BULK CC
Sidewall Lining
Decompression
Panel FWD/
AFT CC
Partition Wall
FR34/ FR35.5/
FR47/ FR47.2/
FR65
Door Panel
FR28/ FR52A/
FR55A/ FR56/
FR59
Decompression
Panel Door
Panel FR28/
FR52A/
FR55A/ FR56/
FR59
ACT Heat
Shield Panel
Protection
Panel Partition
Wall FR24A
Sandwich Panel 12.9 mm Partition Wall no Gillfab 4422-508 Stratitex H2550-
(0.508 in.) C24A G-001
Decompression
Panel Partition
Wall FR24A
h-Profile 8.2 mm Decompression no Gillfab 3072A Stratiglass
0.323 in Panel Ceiling 4000-1B
FWD/ AFT/
BULK

Page 6005
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

h-Profile 10.0 in Decompression no Gillfab 3072B Stratiglass

0.394 in Panel 4000-2B
Door Panel
FR28
Door Panel
FR52A/ FR55A
Door Panel
FR56/ FR59
h-Profile 13.1 mm Decompression no Gillfab 3072C Stratiglass
(0.516 in.) Panel Partition 4000-3B
Wall FR24A
Laminates 1.52 mm Covering Above no Gillfab Stratiglass
0.060 in Bulk Door 1367A-060 8000-5
Replacement of E-Glass Cargo Lining
TABLE 1

Manufacturer Manufacturer
The Gill Hutchinson- Les
Corporation Stratifies
AIM 2001 AIM 3455
aftermarket.strativer@hut
info@thegillcorp.com
Cargo Lining OEM Panel Location Restriction Alternative Alternative
Category Thickness Semi-Finished Semi-Finished
Material Material
Sandwich Panel 7.4 mm For Cargo no Gillfab 4422-295 Stratitex H2550-
(0.291 in.) Loading/ A-001
Occasional Bulk
Configuration:
Ceiling Lining
FWD and AFT
Decompression
Panel Ceiling
FWD/ AFT

Page 6006
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

Sandwich Panel 7.6 mm For STD Bulk no Gillfab 4422-307 Stratitex H2550-
(0.299 in.) /STD Bulk & B-001
CLS
Configuration:
Ceiling Lining
FWD/ AFT/
BULK CC
Decompression
Panel Ceiling
FWD/ AFT/
BULK CC
Sandwich Panel 8.12 mm ) Ceiling Lining no Gillfab 4422-315 Stratitex H2550-
(0.315in.) Cargo Door C-001
Area FWD/
AFT CC
Sandwich Panel 8.4 mm ) For Cargo no Gillfab 4422-331 Stratitex H2550-
(0.331 in.) Loading/ L-001
Occasional Bulk
Configuration:
Sidewall Lining
FWD and AFT
Decompression
Panel Sidewall
Lining FWD/
AFT
Partition Wall
FR34/ FR35/
FR35.5/ FR47/
FR47.2
Decompression
Panel Partition
FR34/ FR35/
FR35.5

Page 6007
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

Sandwich Panel 8.8 mm ) For STD Bulk no Gillfab 4422-346 Stratitex H2550-
(0.346 in.) /STD Bulk & M-001
CLS
Configuration:
Sidewall Lining
FWD/ AFT/
BULK CC
Sidewall Lining
Decompression
Panel FWD/
AFT CC
Partition Wall
FR34/ FR35/
FR35.5/ FR47/
FR47.2/ FR65
Door Panel
FR28/ FR52A/
FR55A/ FR56/
FR59
Decompression
Panel FR28/
FR34/ FR35/
FR35.5 FR52A/
FR55A/ FR56/
FR59
Sandwich Panel 9.8 mm ACT Heat no Gillfab 4422-386 Stratitex H2550-
(0.386 in) Shield Panel E-001
Protection
Panel Partition
Wall FR24A
Sandwich Panel 15.5 mm Partition Wall no Gillfab 4422-610 Stratitex H2550-
(0.610 in) FR24A H-001
Decompression
Panel Partition
Wall FR24A
Laminates 1.02 mm ) Sidewall Lining no Gillfab Stratiglass
(0.040 in.) Flame Covers 1367A-040 8000-3
(Ref.
D255-70427)

Page 6008
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

Laminates 1.52 mm Covering Above no Gillfab Stratiglass

(0.060 in.) Bulk Door 1367A-060 8000-5
Replacement of S-Glass Cargo Lining
TABLE 2

Page 6009
25-50-00 Oct 01/20
 @AIRBUS
COMPONENT MAINTENANCE MANUAL
ATA255000SA320

**For PN’s ALL

FIND AND IDENTIFY THE WASHER OF THE FASTENER ELEMENT INSTALLED

ON YOUR CARGO LINING

STUD − ABS0336 STUD − ABS0336 ELEMENT − ABS1847

WASHER − DAN 125−5 WASHER − ABS0208−02 WITH STAINLESS
ALUMINUM, METALLIC, STEEL, SILVER
METALLIC ANODIZED WHITE COATED METALLIC WASHER

REPLACEMENT OF REPLACEMENT OF LOCALLY MADE CARGO

E−GLASS S−GLASS LINING REPLACEMENT
CARGO LINING CARGO LINING IS NOT PERMITTED
SEE TABLE 1 SEE TABLE 2
REPLACE WITH
ORIGINAL EQUIPMENT
MANUFACTURER
(OEM) PART

F_CM_255000_1_0040102_01_00

Replacement of Cargo Lining - Identification Questionnaire

FIGURE-25-50-00-991-004-A01

Page 6010
25-50-00 Oct 01/20