Technical data HS 8050 HD

Hydraulic crawler crane

Courtesy of Crane.Market
 Dimensions
Basic machine with undercarriage

7350 3000
2860

3300
1700

1120

990
1200 2360

310
4710 700
5650 4300
50
40
=
R

11250

Operating weight Remarks

The operating weight includes the basic machine with HD under- 1. The lifting capacities stated are valid for lifting operation only
carriage, 2 main winches 160 kN including wire ropes (60 m) and (corresponding with crane classification according to F.E.M.
11 m main boom, consisting of A–frame, pulley block, boom foot 1.001, crane group A1).
(5.5 m) and boom head (5.5 m), 16.4 t basic counterweight, 700 mm
3-web grousers and 50 t hook block. 2. Crane standing on firm, horizontal ground.
3. The weight of the lifting device (hoisting ropes, hook block,
Total weight approx. 59.6 t
shackle etc.) must be deducted from the gross lifting capacity
to obtain a net lifting value.

Ground pressure 4. Additional equipment on boom (e.g. boom walkways, auxiliary

jib) must be deducted to get the net lifting capacity.
Ground bearing pressure 0.91 kg/cm2
5. For max. wind speed please refer to lift chart in operator‘s cab
or manual.

Equipment 6. Working radii are measured from centre of swing and under
load.
Main boom (No. 1310.17) max. length 50 m
Main boom (No. 1311.18) max. length 47 m 7. The lifting capacities are valid for 360 degrees of swing.
Fixed jib (No. 0806.xx) upon request 8. Calculation of stability under load is based on ISO 4305
Modular designed equipment for operation as crane, with dragline or Table 1 + 2, tipping angle 4°.
clamshell.
For dragline operation, a rotating fairlead is fitted into the boom foot. 9. The structures are calculated according to F.E.M. 1.001 - 1998
This minimizes the rope angle to drum, which results in lower rope (EN 13001-2 / 2004).
wear.

2 HS 8050 HD

Courtesy of Crane.Market
 Transport dimensions and weights
Basic machine and boom (No. 1310.17)

Basic machine
with HD undercarriage, boom foot, pulley block, A-frame,
2990 2x 160 kN winches including wire ropes (60 m), without basic
counterweight
Width 3000 mm
700 1600 310 Weight 41600 kg
11250 3000

Boom section (No. 1310.17) 3 m

1250
Width 1430 mm
Weight* 300 kg
3140

1250 Boom section (No. 1310.17) 6 m

Width 1430 mm
6140 Weight* 480 kg

1250
Boom section (No. 1310.17) 12 m
12140 Width 1430 mm
Weight* 880 kg

1980
Boom head ** (No. 1310.17)
6300 Width 1430 mm
Weight* 1140 kg

*) Including pendant ropes, without auxiliary equipment **) Polyamide sheaves

Transport dimensions and weights

Main boom (No. 1311.18)

Boom foot (No. 1311.18)

1350
Width 1430 mm
Weight* 1570 kg
5700

1350
Boom section (No. 1311.18) 3 m
Width 1430 mm
3140 Weight* 390 kg

1350 Boom section (No. 1311.18) 6 m

Width 1430 mm
6140 Weight* 620 kg

1350 Boom section (No. 1311.18) 12 m

Width 1430 mm
12140
Weight* 1085 kg

1900 Boom head ** (No. 1311.18)

Width 1430 mm
6300 Weight* 1420 kg

*) Including pendant ropes, without auxiliary equipment **) Polyamide sheaves

HS 8050 HD 3
Courtesy of Crane.Market
 Transport dimensions and weights
Counterweight

Counterweight
Width 1145 mm
1540
Weight* 16400 kg

3000 1145

Hooks

50 t hook block – 2 sheaves

750 Width 350 mm
Weight 900 kg
1650
32 t hook block – 1 sheave
940 Width 350 mm
Weight 515 kg
1800

350
12 t single hook
Width 350 mm
1000
Weight 300 kg

4 HS 8050 HD

Courtesy of Crane.Market
 Technical description

Engine Main winches

Power rating according to ISO 9249, 270 kW (362 hp) at 1700 rpm Winch options:
Engine type Liebherr D 936 A7 SCR Line pull 1st layer
Fuel tank 800 l capacity with continuous level (nom. load) 80 kN 120 kN 160 kN
indicator and reserve warning Rope diameter 20 mm 24 mm 26 mm
Engine complies with NRMM exhaust certification EPA/CARB Tier 4i or Drum diameter 420 mm 525 mm 550 mm
97/68 EC Stage III B. Rope speed 0–126 m/min 0-130 m/min 0-108 m/min
Rope capacity 1st layer 42.5 m 40 m 41.5 m
ECO-Silent-Mode: The winches are outstanding in their compact design and easy
For work not requiring high engine power, the diesel engine can be assembly. Clutch and braking functions on the free-fall system are
operated in the ECO-Silent-Mode (e.g. for inserting reinforcement provided by a compact designed, low wear and maintenance-free
cages, for dragline or lift crane operation). multi–disc brake.
Due to the ECO-Silent-Mode which can be preselected by the operator The drag and hoist winches use pressure controlled, variable flow
the engine runs with optimum fuel efficiency. This lowers consumption hydraulic motors. This system features sensors that automatically
and reduces noise emission. adjust oil flow to provide max. winch speed depending on load.
Option:
• Tagline winch 20 kN with free fall

Hydraulic system
A double axial displacement pump with integrated gearbox supplies
the open loop hydraulic system, allowing all functions to be operated
simultaneously. To minimize peak pressure an automatically working
pressure cut-off is integrated. All filters are electronically monitored. Crawlers
The use of synthetic environmentally friendly (biodegradable) oils is
possible. Ready made hydraulic retrofit kits are available to customize The track width of the undercarriage is changed hydraulically.
requirements e.g. powering casing oscillators, VM–vibrators, hydraulic Propulsion through axial piston motor, hydraulically released spring
grabs, fixed leaders etc. loaded multi–disc brake, maintenance-free crawler tracks, hydraulic
Working pressure max. 320 bar chain tensioning device.
Oil tank capacity 650 l 3-web grousers 700 mm
Drive speed 0 – 1.25 km/h
Option:
• 2-speed hydraulic motor for higher travel speed

Boom winch
Line pull max. 2x 50 kN
Rope diameter 18 mm
Boom up 45 sec. from 15° to 82°

Control
The core of the Liebherr hydraulic crawler cranes is the Litronic control
system.
Swing Developed and manufactured by Liebherr, this comprehensive system
encompasses all control and monitoring functions and is designed
Consists of rollerbearing with external teeth for lower tooth flank to withstand extreme temperature changes and the rough heavy
pressure, fixed axial piston hydraulic motor, spring loaded and duty tasks common in the construction industry. Complete machine
hydraulically released multi–disc holding brake, planetary gearbox and operating data, warnings and failure indications are clearly displayed in
pinion. the required language on the high resolution monitor in the operator’s
Swing speed from 0–4.5 rpm continuously variable, selector for 3 cab.
speed ranges to increase swing precision. Documentation of operating data (PDE) enables optimum diagnosis as
well as early detection and prevention of more serious defects.
An electro-hydraulic proportional control allows several movements to
be performed simultaneously. This ensures that all categories of loads
can be positioned with utmost precision.
Noise emission Options:
• PDE: Process data recording
Noise emissions correspond with 2000/14/EC directive on noise • GSM/GPRS telematics module
emission by equipment used outdoors. • Special demolition control system

HS 8050 HD 5
Courtesy of Crane.Market
 Equipment (main boom No. 1310.17 and 16.4 t counterweight)
Slurry wall grab and clamshell

Slurry wall grab* Clamshell*

Winch options 2 x 160 kN Winch options 2 x 160 kN
Line speed 1st layer 0–130 m/min Line speed 1st layer 0–130 m/min
Max. chisel weight 10 t

*) Load chart for duty cycle operation see page 8

6 HS 8050 HD

Courtesy of Crane.Market
Equipment (main boom No. 1310.17 and 16.4 t counterweight)
Casing oscillator

Casing oscillator*
Winch options 2 x 160 kN
Line speed 1st layer 0–130 m/min
Drilling diameter 1500 mm

HS 8050 HD 7
Courtesy of Crane.Market
 Load chart for duty cycle operation (main boom No. 1310.17)
16.4 t counterweight

Capacities in metric tonnes for boom lengths (11 m - 32 m) - with 160 kN winches
Boom length (m)
Radius 11 14 17 20 23 26 29 32 Radius
(m) t t t t t t t t (m)
4.1 24.2 4.1
5 24.2 24.2 24.2 24.2 5
6 24.0 23.6 23.1 23.2 21.3 18.6 6
7 21.8 21.3 20.9 20.0 19.2 18.3 16.0 14.0 7
8 18.6 18.3 18.0 17.5 17.1 16.2 15.2 14.0 8
9 16.3 16.0 15.7 15.5 15.0 14.7 13.8 12.9 9
10 14.4 14.2 14.0 13.6 13.5 13.0 12.8 12.0 10
12 11.3 11.3 11.2 11.0 10.6 10.4 10.1 12
14 9.2 9.2 9.2 9.2 8.9 8.7 8.5 14
16 7.7 7.7 7.7 7.6 7.5 7.4 16
18 6.6 6.6 6.5 6.5 6.3 18
20 5.7 5.7 5.6 5.6 5.5 20
22 5.0 4.9 4.9 4.8 22
24 4.3 4.3 4.2 24
26 3.8 3.7 26
28 3.4 3.3 28
30 2.9 30
TLT 11225436 M00000 Offiziell

1) Lifting a load exceeding the line pull of one winch is only allowed
Maximum capacity in duty cycle operation with standard ropes
if it can be ensured that each individual winch is not overloaded.
Line pull kN 80 120 160 When working with a mechanical 2-rope grab the total load
to be lifted is limited by the line pull of one winch.
Rope diameter mm 20 24 26 Rigging and ropes are part of the load.
Minimum breaking load kN 365 517 615
2) Max. capacities in metric tonnes do not exceed 75% of
Line pull - 1-rope duty cycle operation t 8 12 16 tipping load. Crane standing on firm, horizontal ground.
Line pull - 2-rope duty cycle operation 1) t 12.1 18.2 24.2

Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
All loads and counterweight configurations are max. values and must not be exceeded.
Weight of additional equipment on boom (e.g. walkways, hose drums etc.) must be deducted to get the net capacity.

8 HS 8050 HD

Courtesy of Crane.Market
Dragline equipment
16.4 t counterweight - main boom (No. 1310.17)

Capacities in metric tonnes for boom lengths (11 m - 26 m)

Boom length (m)
C
11 14 17 20 23 26
alpha C J C J C J C J C J C J
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
45 9.8 9.0 14.9 11.9 11.1 11.5 14.0 13.3 9.2 16.1 15.4 7.6 18.2 17.5 6.4 20.4 19.6 5.5
40 10.4 8.3 13.8 12.7 10.2 10.5 15.0 12.1 8.5 17.3 14.1 6.9 19.6 16.0 5.9 21.9 17.9 5.0
J
35 10.9 7.5 12.9 13.4 9.2 9.8 15.8 10.9 7.9 18.3 12.6 6.4 20.7 14.4 5.4 23.2 16.1 4.5
30 11.4 6.6 12.1 14.0 8.1 9.2 16.6 9.6 7.4 19.2 11.1 6.0 21.8 12.6 5.0 24.4 14.1 4.2
25 11.8 5.8 11.0 14.5 7.0 8.7 17.2 8.3 7.0 19.9 9.6 5.7 22.6 10.8 4.8 25.4 12.1 4.0
TLT 11225436 M00000 Offiziell

E D
Max. capacities in metric tonnes do not exceed 75% of tipping load.
Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
The size of the bucket has to be determined according to local conditions.

Digging diagram
C = Radius / dumping radius
D = Max. digging radius = approx.
C + 1/3 to 1/2 J
E = Digging depth = approx.
40 - 50% of C
J = Height to centre rope pulley
boom head

Clamshell equipment
16.4 t counterweight - main boom (No. 1310.17)

Capacities in metric tonnes for boom lengths (11 m - 26 m)

Boom length in (m)
1500 C
11 14 17 20 23 26
alpha C J C J C J C J C J C J)
(m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t (m) (m) t
K 65 6.7 11.4 21.9 8.0 14.1 17.2 9.3 16.8 14.1 10.6 19.5 11.8 11.8 22.3 10.2 13.1 25.0 8.8
60 7.6 10.9 18.6 9.1 13.5 14.5 10.6 16.1 11.8 12.1 18.7 9.9 13.6 21.3 8.4 15.1 23.9 7.3
55 8.4 10.3 16.2 10.1 12.8 12.6 11.8 15.3 10.2 13.5 17.7 8.5 15.2 20.2 7.2 17.0 22.6 6.2
J 50 9.1 9.7 14.5 11.0 12.0 11.2 12.9 14.3 9.0 14.9 16.6 7.5 16.8 18.9 6.3 18.7 21.2 5.4
45 9.8 9.0 13.1 11.9 11.1 10.1 14.0 13.3 8.1 16.1 15.4 6.7 18.2 17.5 5.7 20.4 19.6 4.8
40 10.4 8.3 12.1 12.7 10.2 9.3 15.0 12.1 7.4 17.3 14.1 6.1 19.6 16.0 5.2 21.9 17.9 4.4
35 10.9 7.5 11.3 13.4 9.2 8.6 15.8 10.9 6.9 18.3 12.6 5.6 20.7 14.4 4.7 23.2 16.1 4.0
30 11.4 6.6 10.7 14.0 8.1 8.1 16.6 9.6 6.5 19.2 11.1 5.3 21.8 12.6 4.4 24.4 14.1 3.7
25 11.8 5.8 10.2 14.5 7.0 7.7 17.2 8.3 6.2 19.9 9.6 5.0 22.6 10.8 4.2 25.4 12.1 3.5
TLT 10225434 M00000 Offiziell

Max. capacities in metric tonnes do not exceed 66.7% of tipping load.

Working diagram Capacities in duty cycle operation are for reference only and are not programmed in the LMI system.
C = Radius / dumping radius
J = Height of boom head sheave
centre above ground level
K = Length of clamshell
(according to manufacturer‘s
specification)

HS 8050 HD 9
Courtesy of Crane.Market
 Working range - main boom (No. 1310.17) 82° – 15°
16.4 t counterweight

ft m
200
60
Auxiliary jib 16 t

56
180

52
70°
160
48
°
60
44
140 1600
°
50 m
40 0 The maximum capacity of
5 the auxiliary jib is 16 t. The
m corresponding load chart
120 47
36 m is programmed in the LMI
44 system.
m
°

41
40

32
100 m
38
m
28 35
m
32
°

80
30

24 m
29
m
26
20 m
60 23
m
20°

16 20
m
17
15°

40 m
12 14
m
11
8
20
4

0 0
48 44 44 36 32 28 24 20 16 12 8 4 0m

160 140 120 100 80 60 40 20 0 ft

Main boom configuration (No. 1310.17)

Configuration for boom lengths (11 m - 50 m)
Length Amount of boom extensions
Boom foot 5.5 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom section 3.0 m 1 1 1 1 1 1 1
Boom section 6.0 m 1 1 1 1 1 1
Boom section 12.0 m 1 1 1 1 2 2 2 2 3 3
Boom head 5.5 m 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom length (m) 11 14 17 20 23 26 29 32 35 38 41 44 47 50

10 HS 8050 HD

Courtesy of Crane.Market
 Load chart for lift crane operation (main boom No. 1310.17)
16.4 t counterweight

Capacities in metric tonnes for boom lengths (11 m - 50m) - with 160 kN winches
Boom length (m)
Radius 11 14 17 20 23 26 29 32 35 38 41 44 47 50 Radius
(m) t t t t t t t t t t t t t t (m)
4 47.0 46.2 4
5 38.1 37.5 35.7 34.0 32.2 5
6 31.5 30.2 28.9 27.7 26.6 25.5 24.5 6
7 25.0 25.1 24.2 23.3 22.5 21.7 20.9 20.2 19.5 18.8 7
8 20.7 20.7 20.8 20.0 19.4 18.8 18.2 17.6 17.0 16.5 16.0 14.4 8
9 17.6 17.6 17.6 17.6 17.0 16.5 16.0 15.5 15.1 14.6 14.2 13.7 13.3 12.2 9
10 15.2 15.3 15.3 15.2 15.1 14.7 14.3 13.8 13.5 13.1 12.7 12.3 11.9 11.6 10
12 11.8 11.9 11.9 11.9 11.9 11.8 11.7 11.4 11.1 10.8 10.4 10.2 9.9 9.5 12
14 9.7 9.8 9.7 9.7 9.7 9.6 9.5 9.3 9.0 8.8 8.5 8.3 8.0 14
16 8.1 8.1 8.1 8.0 8.0 7.9 7.9 7.7 7.5 7.2 7.0 6.8 16
18 6.9 6.9 6.9 6.8 6.8 6.7 6.6 6.6 6.4 6.2 6.0 5.7 18
20 5.9 5.9 5.9 5.8 5.7 5.7 5.6 5.5 5.3 5.1 4.9 20
22 5.2 5.1 5.1 5.0 4.9 4.9 4.8 4.6 4.5 4.2 22
24 4.5 4.4 4.3 4.3 4.2 4.1 4.1 3.9 3.7 24
26 3.9 3.9 3.8 3.8 3.7 3.6 3.5 3.4 3.2 26
28 3.5 3.4 3.3 3.3 3.2 3.1 3.0 2.8 28
30 3.0 3.0 2.9 2.8 2.7 2.6 2.5 30
32 2.6 2.6 2.5 2.5 2.4 2.3 2.2 32
34 2.3 2.2 2.2 2.1 2.0 1.9 34
36 2.0 1.9 1.8 1.8 1.7 36
38 1.7 1.7 1.6 1.5 1.4 38
40 1.5 1.4 1.3 1.2 40
42 1.2 1.1 1.1 42
44 1.0 44
TLT 11220180 M00000 Offiziell

Above load chart is for reference only. For actual lift duty please refer to load chart in operator’s cab or manual.

HS 8050 HD 11
Courtesy of Crane.Market
 Working range - main boom (No. 1311.18) 82° – 15°
16.4 t counterweight

ft m
200
60
Auxiliary jib 20 t

56
180

52
82°
160
48
70°

44 °
60
140 1600

40 The maximum capacity of

°
50 the auxiliary jib is 20 t. The
m corresponding load chart
120 47 is programmed in the LMI
36 m
44 system.
m
°
40

32 41
100 m
38
m
28 35
m
32
80 24 m
29
°
30

m
26
20 m
60 23
m
20°

16 20
m
17
m
15°

40 12 14
m
11
8
20
4

0 0
48 44 44 36 32 28 24 20 16 12 8 4 0m

160 140 120 100 80 60 40 20 0 ft

Main boom configuration (No. 1311.18)

Configuration for boom lengths (11 m - 47 m)
Length Amount of boom extensions
Boom foot 5.5 m 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom section 3.0 m 1 1 1 1 1 1
Boom section 6.0 m 1 1 1 1 1 1
Boom section 12.0 m 1 1 1 1 2 2 2 2 3
Boom head 5.5 m 1 1 1 1 1 1 1 1 1 1 1 1 1
Boom length (m) 11 14 17 20 23 26 29 32 35 38 41 44 47

12 HS 8050 HD

Courtesy of Crane.Market
 Load chart for lift crane operation (main boom No. 1311.18)
16.4 t counterweight

Capacities in metric tonnes for boom lengths (11 m - 47 m) - with 160 kN winches
Boom length (m)
Radius 11 14 17 20 23 26 29 32 35 38 41 44 47 Radius
(m) t t t t t t t t t t t t t (m)
3.4 51.3 3.4
4 47.3 46.5 4
5 38.2 37.5 35.6 33.8 23.3 5
6 31.4 30.1 28.8 27.5 26.4 25.3 24.3 6
7 24.9 25.0 24.0 23.1 22.3 21.5 20.7 19.9 19.2 7
8 20.6 20.6 20.6 19.9 19.2 18.6 17.9 17.3 16.7 16.2 15.6 15.2 8
9 17.5 17.5 17.5 17.4 16.8 16.3 15.8 15.3 14.8 14.3 13.8 13.4 12.9 9
10 15.1 15.1 15.1 15.1 14.9 14.5 14.0 13.6 13.2 12.8 12.3 12.0 11.7 10
12 11.8 11.8 11.8 11.7 11.8 11.6 11.4 11.1 10.8 10.4 10.1 9.8 9.5 12
14 9.6 9.6 9.5 9.5 9.5 9.4 9.2 9.0 8.7 8.4 8.2 7.9 14
16 8.0 7.9 7.9 7.8 7.8 7.7 7.6 7.4 7.1 6.9 6.7 16
18 6.7 6.7 6.7 6.6 6.5 6.4 6.4 6.3 6.1 5.9 5.7 18
20 5.7 5.7 5.7 5.6 5.5 5.4 5.3 5.2 5.0 4.8 20
22 5.0 4.9 4.8 4.7 4.7 4.6 4.5 4.3 4.1 22
24 4.3 4.2 4.1 4.0 3.9 3.8 3.7 3.6 24
26 3.7 3.7 3.6 3.5 3.4 3.3 3.2 3.1 26
28 3.2 3.1 3.1 3.0 2.9 2.8 2.7 28
30 2.7 2.7 2.6 2.5 2.4 2.3 30
32 2.4 2.3 2.2 2.1 2.0 2.0 32
34 2.0 1.9 1.8 1.7 1.7 34
36 1.7 1.6 1.5 1.4 36
38 1.4 1.4 1.2 1.2 38
40 1.1 1.0 40
TLT 11243470 M00000 Offiziell

Above load chart is for reference only. For actual lift duty please refer to load chart in operator’s cab or manual.

HS 8050 HD 13
Courtesy of Crane.Market
 Notes

14 HS 8050 HD

Courtesy of Crane.Market
Notes

HS 8050 HD 15
Courtesy of Crane.Market
 HS 8050 HD—809944214 -04/2014 Subject to change without notice.

Liebherr-Werk Nenzing GmbH

Dr. Hans Liebherr Str. 1, 6710 Nenzing/Austria
Tel.: +43 50809 41–473, Fax: +43 50809 41–499
crawler.crane@liebherr.com, www.liebherr.com
facebook.com/LiebherrConstruction
Courtesy of Crane.Market
Powered by TCPDF (www.tcpdf.org)