R-9000E

Next Generation
Software Defined
HF Receiver

The Sunair R-9000E is a proven solution in communications A large TFT display shows the unit’s operating status in
applications requiring rugged, reliable, and flexible English, while its advanced built-in-test (BITE) capability
equipment. It is intended for use in conjunction with the provides feedback to the lowest replaceable unit (LRU)
T-9000E in split site configuration or as a standalone receiver. level with messages on the display and internal LED
indications. The R-9000E can operate from both ac and dc
This next generation receiver operates in AME, NB-FM, voltage sources, while its internal power supply minimizes
USB, LSB, ISB, CW, Data, and MELPe-based Digital Voice undesirable RFI and EMC effects.
modes. The R-9000E uses software defined digital signal
processing (DSP) technology, which supports the latest The radio’s intuitive modular design allows for ease of
developments in high-speed waveform processing. This maintenance, expansion, and upgrade throughout the
technology enhances the functionality of the CPU as well as equipment life cycle at minimal expense. Thousands of
the Synthesizer, Audio, and IF stages. these radios are in daily service as integral components of
critical strategic communications solutions worldwide.
The radio offers Automatic Link Establishment (ALE) as an
• Analog or VoIP audio interface
internal option (check availability prior to placing order) in
accordance with MIL-STD-188-141 A/B/C, FS1045A, and • Software defined SSB and ISB configurations
S4538. Remote control and programming is possible via • DSP based syllabic squelch
Ethernet or serial port. A serial port connector on the front
panel allows for changes in the unit’s configuration. • Remote control via serial and Ethernet
• Comprehensive BITE to LRU
When used in combination with the T-9000E Transmitter, a
• Internal ac power supply
factory-installed option allows the R-9000E to comply with
MIL-STD-188-203-1A and STANAG 5511/5522 (TADIL-A/ • Data Link - MIL-STD-188-203-1A TADIL A and
Link 11 and NILE/Link 22) for data link operation. The Link 11/22 (factory installed option when used in
R-9000E is also compatible with MIL-STD-188-110 A/B/C combination with the T-9000E)
and STANAG HF modem waveforms. The radio can • HF Data - MIL-STD-188-110 A/B/C and STANAG when
accommodate Type 1 encryption such as ANDVT, KY-99, used in combination with T-9000E)
KG-84(), and KG-40 as well as commercial privacy devices
or optional internal MELPe digital voice F/W with DES 56& • ALE - 2G MIL-STD-188-141 A/B/C and 3G STANAG
AES 256 encryption functions. The audio interface supports 4538, when used in combination with T-9000E (check
analog or VoIP connections. availability)
• Secure Digital Voice (MELPe S4591)
 Product Specifications
GENERAL Manual RF Gain: Front panel and via remote control (forthcoming)
Frequency Range: 10 kHz – 30 MHz Squelch: Syllabic
Frequency Stability: ±1 part in 108 per day (continuous operation) Antenna Input Protection: 100 V RMS, self-resetting
Channels: 128, programmable; non-volatile memory (Flash type) Internal Generated 99.5% of available frequencies from 100 kHz – 30
Spurious: MHz at or below 0.5 μV equivalent input at antenna
Modes of Operation: AM, NB-FM, USB, LSB, ISB, CW, Data, or MELPe digital
terminal
voice
Scan: Manual or automatic
BFO: ±1.99 KHz, 1 Hz resolution INTERNAL OPTIONS
Synthesizer Lock: 10 ms maximum including optional Pre-selector Secure Voice: Embedded option
Tuning Step: 1 Hz to 1 MHz (selectable) ALE: • MIL-STD-188-141 and FS1045A
• MIL-STD-188-141 B/C and STANAG 4538
Remote Interface: Ethernet, RS-232, RS-422, and FSK tone optional
modem Data Link: TADIL/A, Link 11 / 22

Radio Programming: Front panel AUX serial port connector Bandwidth Filters: Custom bandwidth filters and center frequencies available
Low Power Third power setting
RF Input Impedance: 50 ohms, nominal, unbalanced to ground
Antenna Connector: Coaxial, Type N connector, female PERIPHERAL EQUIPMENT OPTIONS
Input Voltage: • 28 Vdc ±15%
• 115/230 Vac, 45 Hz to 400 Hz Mounting: • Shroud and rack slides for EIA standard 19 inch rack
• Automatic ac/dc changeover • Desktop
• Shock mount kit
BITE: Fault isolated to module level (LRU); descriptive readout
on front panel and individual module indication Spares Kits: Running spares, field modules
MTBF: 6500 hours Remote Control: RCU-9310E, Pathfinder II

MTTR: 15 Minutes Pre-selector: F-9800, F-9810

AC Power Control: Remote ON/OFF
Dimensions: Height: 5.95 in (15.1 cm)
Width: 17.83 in (45.3 cm) Messaging: STANAG 5066 (Requires T-9000E)
Length: 17.66 in (44.9 cm)
Weight: 49 lbs (22.3 kg), unpacked
CERTIFICATIONS
Construction: Internal modular plug-in assemblies, field serviceable FCC Part 90, RT: FCC Identifier XVKRT-9000
Origin: Designed and manufactured in the U.S.A. European CE • EN 300 373-2 v1.2.1
Standard (Optional): • EN 301 843-5 v1.1.1
• EN 60950
RECEIVER • Notified Body 1177
Selectivity: • SSB / ISB: 300 – 3300 Hz @ 6 dB
• CW: 500 Hz @ 3 dB, Centered at 1 kHz ENVIRONMENTAL
• AM: ±3000 Hz @ 6 dB
Temperature: • Operating: -30 °C to +55 °C (-22 °F to 131 °F)
Sensitivity: • SSB / ISB: 0.5 μV for 10 dB (S+N)/N • Optional: +60 °C (140 °F)
• CW: 0.3 μV for 10 dB (S+N)/N • Storage: -40 °C to +85°C (-40 °F to 185 °F)
• * AM: 3.0 μV for 10 dB (S+N)/N
Humidity: 95% at 55 °C (122 °F), non-condensing; splash-resistant
Audio Output: • 5 W Into Internal Speaker, <1% THD front panel
• 600 _ Balanced @ -20 dBm to +10 dBm
• Headset: Low Impedance Shock: MIL-STD 810F, Method 516.5, Procedure 1

Audio Response: ±1 dB From 300 – 3050 Hz Vibration: MIL-STD 810F, Method 514.5 & MIL-STD-167-1
Altitude: • Operating: up to 10,000 feet
Image and IF Rejection: 90 dB minimum
• Storage: up to 40,000 feet
Spurious Rejection: 80 dB minimum
AGC Attack Time: 10 ms nominal
AGC Release Time: • Fast: 23 ms nominal
• Medium: 200 ±100 ms nominal
• Slow: 3 ±1 second nominal
AGC Range: 100 dB
AGC Control: No more than 6 dB Change for signal inputs from -100 to
0 dBm; 4 dB for signal inputs from -90 to 0 dBm

3131 SW 42nd Street

Fort Lauderdale, FL 33322
Tel: 954-623-3131/400-5100
Fax: 954-583-7337 www.sunairelectronics.com

Specifications subject to change without notice or obligation. Revised: January 2013