Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 3 views

    HilonFlake 5610-PC

    Uploaded by

    Moin Altaf

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    HilonFlake 5610-PC

    Uploaded by

    Moin Altaf
    3 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3 views2 pages

    HilonFlake 5610-PC

    Uploaded by

    Moin Altaf

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    HilonFlake 5610

    Glass Flake Epoxy

    PRODUCT DESCRIPTION
    A very high solids, low VOC, two component high build epoxy containing chemically resistant glass flake.
    - Excellent corrosion, cathodic disbondment resistance
    - Excellent abrasion resistance
    - Good chemical resistant properties.

    RECOMMENDED USES
    For the protection of steelwork in areas where high abrasion and corrosion resistance are required including splashzone
    areas on offshore structures, jetties, decks, pilings, bridges, chemical plants and water treatment plants. To provide long
    term, anti-corrosive and anti-abrasion protection for above structures. As part of a non-slip deck system in conjunction
    with appropriate aggregate.

    PRODUCT INFORMATION
    Colour EF6102 Grey
    EF6106 Ywllow
    Part B (Curing Agent) GFC610
    Gloss Semi Gloss
    Volume Solids 91%±2%
    Typical Thickness 300-500 microns dry equivalent to 275-1099 microns wet
    Theoretical Coverage 3.03 m²/litre at 300 microns d.f.t
    Mix Ratio Part A(Base) to Part B(Curing Agent)= 1.5：1（by volume）
    Flash Point 36°C

    SURFACE PREPARATION
    All surfaces to be coated should be clean, dry and free from contamination. Prior to paint application all surfaces should be
    assessed and treated in accordance with ISO 8504:2000.Oil or grease should be removed in accordance with SSPC-SP1
    solvent cleaning.
    Bare Steel Abrasive blast clean to Sa2½ (ISO 8501-1:2007). A surface profile of 50-75 microns is
    recommended.
    Shop Primer Approved shop primers must be clean, dry and free from soluble salts and any other surface
    contaminants. Unapproved shop primers will require complete removal by blast cleaning to
    Sa2½ (ISO 8501-1:2007).
    Others Please consult Hilong representative.

    APPLICATION
    Application Condition Surface temperature must always be a minimum of 3°C above dew point. Good ventilation is
    required in confined areas to ensure proper drying. During application and the initial drying of
    the coating, the coating should not be exposed to high humidity.
    This product will not cure adequately below 5°C. For maximum performance ambient curing
    temperatures should be above 10°C.
    Mixing Combine 1.5 parts of Base with 1 part of Curing Agent and mix thoroughly with power agitator.

    Page 1 of 2
    www.hilonggroup.com
    Jul 1，2022
    HilonFlake 5610
    Glass Flake Epoxy

    Pot Life (25°C） 1 hours (Reduced at higher temperature)


    Thinner THR100
    Airless Spray Recommended .
    Tip Range 0.58-0.79 mm (23-31 thou) .
    Total output fluid pressure at spra y tip not less than 210 kg/cm² (300 p.s.i.)
    Air Spray Recommended
    Brush Application by brush is recommended for small areas only.
    Cleaner THR100

    DRYING TIME and OVERCOATING INTERVAL


    Temperature 0°C 10°C 20°C 30°C
    Touch Dry 6 hrs 4 hrs 2 hrs 1 hr
    Hard Dry 26 hrs 15 hrs 7 hrs 3 hrs
    Min. Time Before Overcoating 26 hrs 15 hrs 7 hrs 3 hrs
    Max. Time Before Overcoating 28 days 24 days 21 days 14 days

    SYSTEMS COMPATIBILITY
    HilonFlake 5610 will normally be applied directly to correctly prepared steel, however, the following primers are recommended:
    HilonGuard 2510
    Recommended topcoat are:
    HilonDeco EP 9300 HilonDeco PU 9400
    For other suitable system, please consult Hilong representative.

    UNIT SIZE
    20 litre unit: 12 litres part A (Base) in a 20 litres container, 8 litres part B (Curing agent) in a 10 litres container

    STORAGE
    Must be stored in accordance with national regulations. Store in dry, shaded conditions away from sources of heat and ignition.

    HEALTH and SAFETY


    This product is intended for use only by professional applicators in industrial situations in accordance with the advice given
    on this sheet and the MSDS. All work involving the application and use of this product should be performed in compliance
    with all relevant national, Health, Safety & Environmental standards and regulations.

    NOTE
    The information in this data sheet is not intended to be exhaustive, for your reference only. The information contained in this
    data sheet is liable to modification from time to time in the light of experience and our policy of continuous development.
    Please contact us and request the latest version prior to using the product.

    Page 2 of 2
    www.hilonggroup.com
    Jul 1，2022

    You might also like