Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Msds

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Construction Materials Product Data Sheet

Vetotop UC371
High performance, chemical
scratch & UV resistant polyester
polyurethane floor & wall coating
Uses
u Long-term protection of car parks and floors
in factories, warehouses, laboratories, loading
deck ramps, swimming pools, showers,
kitchens, dairies, breweries.
u UV Resistant top coat over flooring systems
including concrete, epoxies, aromatic elastic
polyurethanes,...etc.
u Apply to floors, walls, and ceilings.
Product Description
Vetotop UC371 is a two-component, solvent-based polyurethane topcoat. It is used as UV resistant sealer over
concrete and the range of Vetotop epoxy and polyurethane flooring & coating systems. Special additives and adhesion
promoters give this material excellent penetration and adhesion to minimally profiled concrete. Vetotop UC371 is UV
stable for exterior applications, cures rapidly, and the sealed system is ideal for all-weather exposure. Vetotop UC371
gives a hard, glossy surface that offers excellent scratch resistance and easy cleanability when used as a finish coat.
Vetotop UC371 is supplied in a pack size of 4 liters kit consist of Resin & Hardener.

Advantages Technical Data


u Fast, easy application.
Vetotop UC371 Typical Values
u Superior abrasion, scratch, and chemical resistance. Solid Content (%Volume) 50
u Low maintenance cost. Recommended DFT / coat 75 - 100
Pot Life @ 12°C (min) 90

Technical Data Sheet -Vetotop UC371


u Hygienic, impervious, and easily cleanable.
Pot Life @ 40°C (min) 25
u Available in 8 standard colors with the possibility of Thin Film Dry Time (hours) @ 12°C 12
custom RAL colors. Application Maximum Relative
75
u High bond, stronger than concrete cohesive Humidity (%)
strength. Bond Strength to Concrete ASTM
> 1.5 MPa
D4541
u Weather-resistant, UV stable, will not degrade, chalk Taber Abrasion ASTM D4060 CS17
or yellow under Ultra Violet light exposure. 10
Wheels (mg loss/1000cycles)
Water Absorption ASTM D413
0.001
(maximum)
Design Criteria Porosity with no sealer NACE Sand
0
Vetotop UC371 is designed to be a hard-wearing thin TM-01-74
coat application on cementitious or metal substrates Skid Resistance (British Pendulum
and a top coat over epoxy and aromatic urethane number - BPN) ASTM E303:
coatings thicknesses between 70 and 100 microns. The DRY: 91
product is used for internal and external applications. Wet: 21
The applied product will be resistant to water as well as Recoat Time 10 -12 Hours
a wide range of chemicals. Elongation ASTM D412 50%
Tensile Strength ASTM D412 7 N/mm2
Standards Compliance
h DIN 53457
h BS EN476:2009 as class 1 in flame spread.
h ASTM E303
Product Data Sheet Construction Materials

Usage Instructions Packaging & Coverage


Surface Preparation Product Pack Size
Vetotop UC371 4 Liters Kit
The surface should be sound, clean, free from loose
material, grease, laitance, dirt curing compound, etc. Product Theoretical Coverage
Laitance and weak surface layer shall be removed 26.5m2 / 4 Liters Kit @ 150
using mechanical methods such as grinding or blasting Vetotop UC371
micron DFT
to provide a sound, well-profiled surface. Repair all
necessary surfaces before application by using epoxy Stated consumption data are for general guidance.
mortar from the Vetorep ER range. Actual consumption depends on the nature of
substrate, method of application, and wastage.
New concrete floors shall be at least 28 days old
with a moisture content of less than 5% (shall earlier In the case of using antislip aggregates, the
application be required testing of substrate for consumption values for the topcoat will increase by
moisture conditions shall be made). 15 - 40%.

It’s mandatory to apply a penetrating primer Vetoprime Shelf Life & Storage
EP490 on the porous substrates before applying
Vetotop UC371. The original sealed kit of Vetotop UC371 has a shelf life
of 12 months, provided it is stored clear of ground in a
Mixing Vetotop UC371 dry and shaded place below 35ºC.
In a separate mixing vessel, use a slow speed mixer
to mix the base, hardener for 3 minutes. Mix these Health & Safety
components in the quantities supplied, taking care Vetotop UC371 is irritant and harmful; therefore, avoid
to ensure all containers are scraped clean. Do not add direct contact with eyes or skin. It is recommended to
solvent thinners at any time. use protective gloves and goggles during application.
In case of contact with eyes, clean immediately with
Application
plenty of clean cold water and seek medical advice.
Apply Vetotop UC371 by roller. The application should
Ensure adequate ventilation when using the product
be at a rate of 6.6 m2/liter per coat.
or when using solvent for cleaning purposes and avoid
The application should not be carried out when vapors’ inhalation. The use of barrier creams provides
humidity exceeds 75% or when the surface temperature additional skin protection. In case of skin contact,
to be coated less than 3°C above the dew point. rinse with plenty of clean water, cleanse with soap and
Technical Data Sheet -Vetotop UC371

Vetotop UC371 can be applied as a single coat or water. Do not use solvent. In case of contact with eyes,
multi-coat sandwich system incorporating Vetograin rinse immediately with plenty of clean water and seek
products to give a slip-resistant finish. For more medical advice. If swallowed, seek medical attention
information, please refer to Vetograin Technical Data immediately - Do not induce vomiting.
Sheet. Vetotop UC371 and Vetonit Solvent XX300 are
flammable. Keep away from sources of ignition. No
Expansion Joints Smoking. In the event of a fire, extinguish with CO2 or
Expansion joints in the existing substrate must be foam.
retained and continued through the Vetotop UC371 Refer to product(s) MSDS for further information.
topping. Saveto has a range of joint sealants specifically
designed for flooring (see Vetoflex PS782 product data
sheet).

Cleaning
Clean tools and equipment with Vetonit Solvent XX300
immediately after use.

LEGAL DISCLAIMER
Saveto endeavors to ensure that any advice, recommendations, information it may give is accurate and correct. It cannot accept any lia-
bility either directly or indirectly arising from the use of its products because it has no direct or continuous control over where or how its
products are applied, whether or not following any advice, specification, recommendation, or information given by us. Saveto has the right
to change any of the technical datasheets’ specifications upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year. Our technical data sheets are continuously updated as per R&D improvements and
new 3rd party testing; kindly refer to our website for the latest updated TDSs.

Ref No.: G3-FC045-11-21 www.saveto.com

You might also like