Tech. Medical Electronics CTS2.0 NSQF-4

GOVERNMENT OF INDIA
MINISTRY OF SKILL DEVELOPMENT & ENTREPRENEURSHIP

DIRECTORATE GENERAL OF TRAINING
COMPETENCY BASED CURRICULUM
TECHNICIAN MEDICAL ELECTRONICS

(Duration: Two Years)
Revised in July 2022
CRAFTSMEN TRAINING SCHEME (CTS)
NSQF LEVEL- 4
SECTOR – ELECTRONICS AND HARDWARE

TECHNICIAN MEDICAL
ELECTRONICS
(Engineering Trade)
(Revised in Jul 2022)
Version: 2.0
CRAFTSMEN TRAINING SCHEME (CTS)
NSQF LEVEL - 4
Developed By
Ministry of Skill Development and Entrepreneurship

Directorate General of Training
CENTRAL STAFF TRAINING AND RESEARCH INSTITUTE
EN-81, Sector-V, Salt Lake City,
Kolkata – 700 091
www.cstaricalcutta.gov.in
CONTENTS
S No. Topics Page No.

1. Course Information 1
2. Training System 2
3. Job Role 6
4. General Information 9
5. Learning Outcome 11
6. Assessment Criteria 13
7. Trade Syllabus 22
8. Annexure I (List of Trade Tools & Equipment) 47

Technician Medical Electronics
1. COURSE INFORMATION
During the two-year duration of Technician Medical Electronics trade a candidate is

trained on professional skill, professional knowledge and Employability skill related to job
role. In addition to this a candidate is entrusted to undertake project work and
extracurricular activities to build up confidence. The broad components covered under
Professional Skill subject are as below: -
FIRST YEAR: In this year, the trainee learns about safety and environment, use of fire
extinguishers, artificial respiratory resuscitation to begin with. He gets the idea of trade
tools & its standardization, Familiarize with basics of electricity. Plan, estimate, assemble,
install and test wiring system in hospital & CSSD department, Identify, install, test and
operate different photo therapy equipments in Biomedical Sector. Skilling to test and
service different batteries used in electronics applications and record the data to estimate
the repair cost. Identify and test various electronics components using proper measuring
instruments, verify characteristics and compare the data using standard parameter.
Demonstrate soldering and de-soldering of various types of electrical components, Plan and
carry out installation, fault detection and repairing of Hospital Electrical appliances. Execute
testing; evaluate performance and maintenance of sphygmomanometers. Test and operate
different types of Physiotherapy Equipment's technique and general care. Test various
Medical gas plant operation using suitable care and safety. The candidate will be able to
Construct, test and verify the input/output characteristics of various analog circuits.
Assemble, test and troubleshoot various digital circuits. Demonstrate the significance of
different parts in the organization in the human body (Basics of Human Anatomy and
Physiology). Execute the operation of different Bio Medical sensors, identify, wire & test
various sensors by selecting appropriate test instruments. Construct and test different
circuits using ICs 741 operational amplifiers & ICs 555 linear integrated circuits and execute
the result. Identify the working principles, Operation, general care of Clinical Lab
Equipments.
SECOND YEAR: In this year, the trainee will be able to detect the faults and troubleshoot
SMPS, UPS, and Inverter and Battery charger. They will also be skilled with various
modulation techniques to acquaint with fibre optic communication techniques transmission
and reception. Trainees will be able to Install, test and maintain a CCTV system and
configure the system for surveillance function in Hospital department. Identify various
functional blocks, I/O ports of a 8085 micro processor system and run the basic program.
Trainees will be able to demonstrate the ICU department functions, equipments, calibration
and basic human rating chart. They will also interpret the factors, tools and techniques
affecting the medical terminology image quality. The trainee will demonstrate function of
bio-medical department. Familiarize with the instruction set of 8051 micro controller kit and
run the application. The trainees will demonstrate the operation and function of dental
chair & dental x-ray. They will also be able operate different imaging equipments used in
hospitals. The trainee will develop a bio-medical department in a hospital for supporting
role of bio-medical engineer.
1
2. TRAINING SYSTEM
2.1 GENERAL
Directorate General of Training (DGT) under Ministry of Skill Development &

Entrepreneurship offers range of vocational training courses catering to the need of
different sectors of Labour market. The vocational training programmes are running under
aegis of Directorate General of Training (DGT). Craftsman Training Scheme (CTS) with
variants and Apprenticeship Training Scheme (ATS) are two pioneer programmes under DGT
for propagating vocational training.
Technician Medical Electronics trade under CTS is one of the popular newly designed
courses. The earlier course was Technician Medical Electronics. The course is of two years
duration. It mainly consists of Domain area and Core area. The Domain area (Trade Theory &
Practical) imparts professional skills and knowledge, while Core area (Employability Skills)
imparts requisite core skill & knowledge and life skills. After passing out the training
program, the trainee is awarded National Trade Certificate (NTC) by DGT which is recognized
worldwide.
Trainee needs to demonstrate broadly that they are able to:
 Read & interpret technical parameters/documentation, plan and organize work

processes, identify necessary materials and tools;
 Perform task with due consideration to safety rules, accident prevention regulations
and environmental protection stipulations;
 Apply professional knowledge, core skills & employability skills while performing the
job and repair & maintenance work.
 Check the job with circuit diagrams/components as per drawing for functioning,
diagnose and rectify faults in the electronics components/module.
 Document the technical parameters in tabulation sheet related to the task
undertaken.
2.2 PROGRESSION PATHWAYS:
 Can join industry as Technician and will progress further as Senior Technician,
Supervisor and can rise up to the level of Manager.
 Can become Entrepreneur in the related field.
 Can take admission in diploma course in notified branches of Engineering by lateral
entry.
 Can join Apprenticeship programme in different types of industries leading to
National Apprenticeship certificate (NAC).
 Can join Crafts Instructor Training Scheme (CITS) in the trade for becoming instructor
in ITIs.
 Can join Advanced Diploma (Vocational) courses under DGT as applicable.
2
2.3 COURSE STRUCTURE:

Table below depicts the distribution of training hours across various course elements
during a period of two years: -
Notional Training Hours

S No. Course Element
1st Year 2nd Year
1 Professional Skill (Trade Practical) 840 840

2 Professional Knowledge (Trade Theory) 240 300
3 Employability Skills 120 60
Total 1200 1200
Every year 150 hours of mandatory OJT (On the Job Training) at nearby industry,
wherever not available then group project is mandatory.
4 On the Job Training (OJT)/ Group Project 150 150
Trainees of one-year or two-year trade can also opt for optional courses of up to 240 hours
in each year for 10th/ 12th class certificate along with ITI certification or add on short term
courses.
2.4 ASSESSMENT & CERTIFICATION
The trainee will be tested for his skill, knowledge and attitude during the period of
course through formative assessment and at the end of the training programme through
summative assessment as notified by the DGT from time to time.
a) The Continuous Assessment (Internal) during the period of training will be done by
Formative Assessment Method by testing for assessment criteria listed against learning
outcomes. The training institute has to maintain an individual trainee portfolio as detailed in
assessment guideline. The marks of internal assessment will be as per the formative
assessment template provided on www.bharatskills.gov.in
b) The final assessment will be in the form of summative assessment. The All India Trade
Test for awarding NTC will be conducted by Controller of examinations, DGT as per the
guidelines. The pattern and marking structure is being notified by DGT from time to time.
The learning outcome and assessment criteria will be the basis for setting question papers
for final assessment. The examiner during final examination will also check the individual
trainee’s profile as detailed in assessment guideline before giving marks for practical
examination.
3
2.4.1 PASS REGULATION
For the purposes of determining the overall result, weightage of 100% is applied for
six months and one year duration courses and 50% weightage is applied to each
examination for two years courses. The minimum pass percent for Trade Practical and
Formative assessment is 60% & for all other subjects is 33%.
2.4.2 ASSESSMENT GUIDELINE
Appropriate arrangements should be made to ensure that there will be no artificial

barriers to assessment. The nature of special needs should be taken into account while
undertaking the assessment. Due consideration should be given while assessing for
teamwork, avoidance/reduction of scrap/wastage and disposal of scrap/waste as per
procedure, behavioral attitude, sensitivity to the environment and regularity in training. The
sensitivity towards OSHE and self-learning attitude are to be considered while assessing
competency.
Assessment will be evidence based comprising some of the following:
 Job carried out in labs/workshop

 Record book/ daily diary
 Answer sheet of assessment
 Viva-voce
 Progress chart
 Attendance and punctuality
 Assignment
 Project work
 Computer based multiple choice question examination
 Practical Examination
Evidences and records of internal (Formative) assessments are to be preserved until

forthcoming examination for audit and verification by examining body. The following
marking pattern to be adopted for formative assessment:
Performance Level Evidence

(a) Marks in the range of 60%-75% to be allotted during assessment
For performance in this grade, the candidate  Demonstration of good skill in the use
should produce work which demonstrates of hand tools, machine tools and
attainment of an acceptable standard of workshop equipment.
craftsmanship with occasional guidance, and  60-70% accuracy achieved while
due regard for safety procedures and undertaking different work with those
4
practices demanded by the component/job.

 A fairly good level of neatness and
consistency in the finish.
 Occasional support in completing the
project/job.
(b) Marks in the range of 75%-90% to be allotted during assessment

For this grade, a candidate should produce  Good skill levels in the use of hand
work which demonstrates attainment of a tools, machine tools and workshop
reasonable standard of craftsmanship, with equipment.
little guidance, and regard for safety  70-80% accuracy achieved while
procedures and practices undertaking different work with those
demanded by the component/job.
 A good level of neatness and
 Little support in completing the
project/job.
(c) Marks in the range of more than 90% to be allotted during assessment
For performance in this grade, the candidate,  High skill levels in the use of hand tools,
with minimal or no support in organization machine tools and workshop
and execution and with due regard for safety equipment.
procedures and practices, has produced work  Above 80% accuracy achieved while
which demonstrates attainment of a high undertaking different work with those
standard of craftsmanship. demanded by the component/job.
 A high level of neatness and
 Minimal or no support in completing
the project.
5
3. JOB ROLE
Bio-Medical Equipment Technician; Electronics Technician; Biomedical Engineering

Technician repairs, calibrates, and maintains medical equipment and instrumentation used
in health-care delivery field: Inspects and installs medical and related technical equipment in
medical and research facilities for use by physicians, nurses, scientists, or engineers involved
in researching, monitoring, diagnosing, and treating physical ailments or dysfunctions.
Services various equipment and apparatus, such as patient monitors, electrocardiographs,
blood-gas analysers, x-ray units, defibrillators, electrosurgical units, anaesthesia apparatus,
pacemakers, blood- pressure transducers, spirometers, sterilisers, diathermy equipment, in-
house television systems, patient-care computers, and other related technical
paraphernalia. Repairs, calibrates, and maintains equipment, using hand tools, power tools,
measuring devices, and knowledge of manufacturers' manuals, troubleshooting techniques,
and preventive-maintenance schedules. Safety-tests medical equipment and health-care
facility's structural environment to ensure patient and staff safety from electrical or
mechanical hazards. Consults with medical or research staff to ascertain that equipment
functions properly and safely, utilizing knowledge of electronics, medical terminology,
human anatomy and physiology, chemistry, and physics.
Medical Equipment Technician; in the Healthcare Industry is also known as a Biomedical

Equipment Technician (BMET), Service Technician, Biomedical Electronics Technician, and
Biomedical Engineering Technician (BMET). Medical Equipment Technicians install, maintain
and repair patient care equipment. They perform inspection, installation, and preventative
maintenance of general clinical equipment, including appropriate documentation for all
service activities and training the hospital staff.
Medical Laboratory Technician; (MLT) is also referred to as Clinical Laboratory Science

professionals, Medical Technologists and Medical Laboratory Scientists. The Medical
Laboratory Technician performs complex tests for diagnosis, treatment, and prevention of
disease. These professionals are responsible for supporting and assisting doctors and
scientists in their day-today healthcare work in a variety of roles. They function as the main
support to biomedical scientists in pathology laboratories. They are also sometimes
responsible for imparting training and supervision to the staff.
Medical Electronics General; fits, assembles and repairs various kinds of Medical electronic
equipment in Hospital or company at place of use. Hospital construction and maintains of
bio-medical departments should Examines drawings and wiring diagrams centralize gas
plant; checks parts for accuracy of fit and minor adjustments; assembles parts or mounts
them on chassis or panels with aid of hand tools; installs and connects wiring, soldering
joints equipment, diagnoses faults with aid of electrical and electronic testing equipment;
dismantles equipment if required and replaces faulty parts or wiring.
Medical Electronics Fitter, other; include all other workers engaged in fitting, assembling,
repairing and manufacture and service medical electronic equipment, machinery,
appliances, etc.
6
Medical Electronics Mechanic; Medical Electronic Equipment Mechanic repairs medical

equipment, such as all medical equipment example Radiology equipment's, ICU
equipment's, control systems following blueprints and manufacturer's specifications and
using hand tools and test instruments. Tests faulty equipment and applies knowledge of
functional operation of medical electronic units and systems to diagnose cause of
malfunction. Tests electronic components and circuits to locate defects, using instruments,
adjusts mechanical parts, using hand tools and soldering iron. Aligns, adjusts and calibrates
testing instruments. Maintains records of repairs, calibrations and test.
ECG Technician (ECG operation); tests programmer ECG lead selector switch with testing
equipment to ensure that assembly in ECG leads, frequency, performance, etc. are in
accordance with prescribed Standards Places assembled ECG leads in position and visually
examines it to ensure that position of equipment, connections, Switches on and operates
different knobs to check calibration, audibility and general performance of set by varying its
tone and listening to various stations and frequencies. Tightens loose leads locates faults,
replaces defective components and conducts necessary changes. Approves correctly
assembled sets for further processing and rejects defective ones for rectification. May tests
sets at different stages of assembly. May service, repair and overhaul ECG leads.
Patient Monitoring system, pulmonary Function Analyses, Blood gas analyzers, Cardiac
Defibrillators Installs, X-ray machine technician Ultrasonic Imaging Systems Functioning. If
the problem identified is in the Printed Circuit Board (PCB), the technician identifies the
specific fault in the PCB and corrects it. Replaces the dysfunctional PCB with a new one, if
the damage identified requires fixing at the service Centre.
Plan and organize assigned work and detect & resolve issues during execution. Demonstrate
possible solutions and agree tasks within the team. Communicate with required clarity and
understand technical English. Sensitive to environment, self-learning and productivity.
Reference NCO-2015:
(i) 3211.0200 – Bio-Medical Equipment Technician
(ii) 3211.0501 – Medical Equipment Technician
(iii) 3212.0701 – Medical Laboratory Technician
Reference NOS:
i) ELE/N0102
ii) ELE/N7812
iii) ELE/N7202
iv) ELE/N4610
v) ELE/N9447
vi) ELE/N9448
vii) ELE/N9449
viii) ELE/N9450
ix) ELE/N9451
x) ELE/N9452
7
xi) ELE/N9453
xii) ELE/N9454
xiii) ELE/N9455
xiv) ELE/N9456
xv) ELE/N9457
xvi) ELE/N9458
xvii) ELE/N9459
xviii) ELE/N9460
xix) ELE/N9461
xx) ELE/N9461
xxi) ELE/N9462
xxii) ELE/N9463
xxiii) ELE/N9464
xxiv) ELE/N9465
xxv) ELE/N9466
xxvi) ELE/N9467
xxvii) ELE/N9468
xxviii) ELE/N9469
8
4. GENERAL INFORMATION
Name of the Trade TECHNICIAN MEDICAL ELECTRONICS
Trade Code DGT/1070
NCO – 2015 3211.0200, 3211.0501, 3212.0701

ELE/N0102, ELE/N7812, ELE/N7202, ELE/N4610, ELE/N9447, ELE/N9448,
NOS Covered ELE/N9455, ELE/N9456, ELE/N9457, ELE/N9458, ELE/N9459, ELE/N9460,
ELE/N9466, ELE/N9467, ELE/N9468, ELE/N9469
NSQF Level Level-4
Duration of Craftsmen
Two Years (2400 hours + 300 hours OJT/Group Project)
Training
Passed 10th class examination with Science and Mathematics or with
Entry Qualification
vocational subject in same sector or its equivalent.
Minimum Age 14 years as on first day of academic session.
Eligibility for PwD LD, LC, DW, AA, LV, DEAF, AUTISM, SLD
Unit Strength (No. Of

24 (There is no separate provision of supernumerary seats)
Student)
Space Norms 120 Sq. mtr (inclusive 10 sq. m dark room area)
Power Norms 2 KW
Instructors Qualification for
1. Technician Medical B.Voc/Degree in Electronics/ BME/ Medical Electronics Engineering
Electronics Trade from AICTE/UGC recognized Engineering College/ university with one-
year experience in the relevant field.
OR
03 years Diploma in Electronics/ BME/ Medical Electronics from AICTE
recognized board of technical education or relevant Advanced Diploma
(Vocational) from DGT with two years’ experience in the relevant field.
OR
NTC/NAC passed in the Trade of "Technician Medical Electronics" With
three years' experience in the relevant field.
Essential Qualification:
Relevant Regular / RPL variants of National Craft Instructor Certificate
(NCIC) under DGT.
NOTE: Out of two Instructors required for the unit of 2(1+1), one must
have Degree/Diploma and other must have NTC/NAC qualifications.
However both of them must possess NCIC in any of its variants.
2. Workshop B.Voc/Degree in Engineering from AICTE/UGC recognized Engineering
9
Calculation & Science College/ university with one-year experience in the relevant field.
OR
03 years Diploma in Engineering from AICTE / recognized board of
technical education or relevant Advanced Diploma (Vocational) from
DGT with two years’ experience in the relevant field.
OR
NTC/ NAC in any one of the engineering trades with three years’
experience.
Regular / RPL variants of National Craft Instructor Certificate (NCIC) in
relevant trade
OR
Regular / RPL variants NCIC in RoDA or any of its variants under DGT
3. Engineering B.Voc/Degree in Engineering from AICTE/UGC recognized Engineering
Drawing College/ university with one-year experience in the relevant field.
OR
03 years Diploma in Engineering from AICTE / recognized board of
technical education or relevant Advanced Diploma (Vocational) from
DGT with two years’ experience in the relevant field.
OR
NTC/ NAC in any one of the Mechanical group (Gr-I) trades categorized
under Engg. Drawing’/ D’man Mechanical / D’man Civil’ with three
years’ experience.
Regular / RPL variants of National Craft Instructor Certificate (NCIC) in
relevant trade
OR
Regular / RPL variants of NCIC in RoDA / D’man (Mech /civil) or any of
its variants under DGT.
4. Employability Skill MBA/ BBA / Any Graduate/ Diploma in any discipline with Two
years’ experience with short term ToT Course in Employability Skills.
(Must have studied English/ Communication Skills and Basic Computer

at 12th / Diploma level and above)
OR
Existing Social Studies Instructors in ITIs with short term ToT Course
in Employability Skills.
5. Minimum Age for 21 Years
Instructor
List of Tools and
As per Annexure – I
Equipment
10
5. LEARNING OUTCOME
Learning outcomes are a reflection of total competencies of a trainee and assessment will
be carried out as per the assessment criteria.
5.1 LEARNING OUTCOMES (TRADE SPECIFIC)
FIRST YEAR
1. Plan and execute soldering and de soldering of various electrical components like
Lug’s, tag’s, clips, Eyelets & Plugs for electronic circuits following safety precautions.
(ELE/N0102)
2. Plan, estimate, assemble, install and test wiring system in hospital & CSSD
department. (ELE/N9447)
3. Identify, install, test and operate different photo therapy equipments in Biomedical
Sector. (ELE/N9448)
4. Plan and carry out installation, fault detection and repairing of Hospital Electrical
appliances. (ELE/N9449)
5. Operate and test clinical equipment/ instruments used in hospital. (ELE/N9450)
6. Test and service different batteries used in electronics applications and record the
data to estimate the repair cost. (ELE/N9451)
7. Identify, place, solder, desolder and test different SMD discrete components and IC
packages with due care and following safety norms using proper tools/setup.
(ELE/N7812)
8. Assemble simple electronics power supply circuit and test for functioning.
(ELE/N9452)
9. Execute testing; evaluate performance and maintenance of sphygmomanometers.
(ELE/N9453)
10. Verify characteristics of electronics, power electronics and Special Semiconductors
circuits. (ELE/N9454)
11. Test various Medical gas plant operation using suitable care and safety. (ELE/N9455)
12. Test and operate different types of Physiotherapy Equipment's technique and
general care. (ELE/N9456)
13. Assemble, test and troubleshoot various digital circuits. (ELE/N7202)
14. Construct, test and verify the input/output characteristics of various analog circuits.
(ELE/N7202)
15. Demonstrate the significance of different parts in the organization in the human
body (Basics of Human Anatomy and Physiology). (ELE/N9457)
16. Execute the operation of different Bio Medical sensors, identify, wire & test various
sensors by selecting appropriate test instruments. (ELE/N9458)
17. Construct and test different circuits using ICs 741 operational amplifiers & ICs 555
linear integrated circuits and execute the result. (ELE/N9459)
18. Identify the working principles, Operation, general care of Clinical Lab Equipments.
(ELE/N9460)
19. Read and apply engineering drawing for different application in the field of work.s
20. Demonstrate basic mathematical concept and principles to perform practical
operations. Understand and explain basic science in the field of study.
11
SECOND YEAR
21. Detect the faults and troubleshoot SMPS, UPS, and Inverter and Battery charger.
(ELE/N7202)
22. Prepare fibre optic setup and execute transmission and reception. (ELE/N9461)
23. Install, test and maintain a CCTV system and configure the system for surveillance
function in Hospital department. (ELE/N4610)
24. Identify, test, service & program 8085 Micro-processor. (ELE/N9462)
25. Demonstrate ICU Department functions, equipments etc., calibration and basic
human rating chart. (ELE/N9463)
26. Interpret the factors, tools and techniques affecting the medical terminology image
quality. (ELE/N9464)
27. Demonstrate the functions of bio-medical Department. (ELE/N9465)
28. Identify, test, service and program Micro controller 8051. (ELE/N9466)
29. Demonstrate various operations and functions of Dental Chair & Dental X-Ray.
(ELE/N9467)
30. Execute the operation of different of Imaging Equipments used in hospitals.
(ELE/N9468)
31. Recognize development of a Bio-medical Department in a hospital. (ELE/N9469)
32. Read and apply engineering drawing for different application in the field of work.
33. Demonstrate basic mathematical concept and principles to perform practical
operations. Understand and explain basic science in the field of study.
12
6. ASSESSMENT CRITERIA
LEARNING OUTCOMES ASSESSMENT CRITERIA
FIRST YEAR
1. Plan and execute soldering Plan work in compliance with standard safety norms.
and de soldering of various Identify different types of Electrical components and test.
electrical components like Identify various types of lug’s and test the polarity.
Lug’s, tag’s, clips, Eyelets & Identify different types of tag’s, clips, Eyelets & plug and test
Plugs for electronic circuits the polarity.
following safety Solder the given components.
precautions. (ELE/N0102) Avoid waste, ascertain unused materials and components for
disposal, store these in an environmentally appropriate manner
and prepare for disposal.
2. Plan, estimate, assemble, Comply with safety & IE rules when performing the wiring.
install and test wiring Prepare and mount the energy meter board.
system in hospital & CSSD Draw and wire up the consumers main board with ICDP switch
department. (ELE/N9447) and distribution fuse box.
Draw and wire diagram of all CSSD equipment's
Identify the types of fuses their ratings and applications.
Identify the parts of a relay, MCB & ELCB and check its
operation.
Estimate the cost of material for wiring in PVC channel for an
office room having 2 lamps, 1 Fan, one 6A socket outlet and
wire up.
Estimate the requirement for conduit wiring (3 phase) and wire
up.
Estimate the materials and wire up the lighting circuit for a
godown.
Estimate the materials and wire up a lighting circuit for a
corridor in conduit.
Test, locate the fault and repair Hospital wiring installation.
3. Identify, install, test and Install light fitting with reflectors for direct and indirect lighting.
operate different photo Assemble and connect single & twin tube fluorescent light.
therapy equipments in Connect, install and test the HPMV & HPSV lamp with
Biomedical Sector. accessories.
(ELE/N9448) Prepare and test a decorative serial lamp set for 240 V using 6V
bulb and flasher.
Install light fitting for show case window lighting.
Plan work in compliance with standard safety norms related
with electrical illumination system.
4. Plan and carry out Plan work in compliance with standard safety norms related
installation, fault with domestic appliances.
detection and repairing of Service and Repair of calling bell/ buzzer/ Alarm.
Hospital Electrical Service and repair an automatic iron.
13
appliances. (ELE/N9449) Repair and service of oven having multi-range heat control.
Replace the heating element in a kettle and test.
Service and repair an induction heater.
Service and repair a geyser.
Service and repair a mixer.
Service and repair of washing machine.
Install a Suction machine .
Service and repair of table fan.
Service, repair and install a ceiling fan.
5. Operate and test clinical Ascertain and select tools and materials for the job and make
equipment/ instruments this available for use in a timely manner.
used in hospital. Plan work in compliance with standard safety norms.
(ELE/N9450) Identify the different types of resistors.
Measure the resistor values using colour code and verify the
reading by measuring in multi meter.
Identify the power rating using size.
Measure the resistance, Voltage, Current through series and
parallel connected networks using multi meter.
Identify different inductors and measure the values using LCR
meter.
Identify the different capacitors and measure capacitance of
various capacitors using LCR meter.
Ascertain and select tools and materials for the job and make
this available for use in.
6. Test and service different Identify Tools and instruments for testing of batteries.
batteries used in Observe safety procedure during testing of batteries and work
electronics applications as per standard norms and company guidelines.
and record the data to Identify the primary and secondary cells.
estimate the repair cost. Measure and test the voltages of the given cells/ battery using
(ELE/N9451) analog / digital multimeter.
Charging and discharging the battery.
Maintain and estimate the repair cost of secondary battery.
Use a hydro meter to measure the specific gravity of the
secondary battery.
7. Identify, place, solder, Identify the various crimping tools for various IC packages.
desolder and test Identify different types of soldering guns and choose the
different SMD discrete suitable tip for the application.
components and IC Demonstrate the soldering and de-soldering the different active
packages with due care and passive components, IC base on GPCBs using solder, flux,
and following safety pump and wick.
norms using proper Make the necessary setting on SMD soldering station to solder
tools/setup. (ELE/N7812) and de-solder various IC’s of different packages by following the
safety norms.
Identify SMD components, de-solder and solder the SMD
components on the PCB.
14
Check the cold continuity, identify loose/dry solder and broken

track on printed wired assemblies and rectify the defects.
Avoid waste, ascertain unused materials and components for
safe disposal.
Identify, solder and desolder the PGA components.
8. Assemble simple Practice soldering on components, lug and board with safety.
electronics power supply Identify the passive /active components by visual appearance,
circuit and test for Code number and test for their condition.
functioning. (ELE/N9452) Identify the control and functional switches in CRO and
measure the D.C. & A.C. voltage, frequency and time period.
Construct and test a half & full wave rectifier with and without
filter circuits.
Construct and test a bridge rectifier with and without filter
circuits.
Construct and test a Zener based voltage regulator circuit.
9. Execute testing; evaluate Plan work in compliance with standard safety norms related
performance and with sphygmomanometers.
maintenance of Identify the types of sphygmomanometer and their
sphygmomanometers. specifications.
(ELE/N9453) Identify terminals, verify the rubber cuff which is apply to the
arms.
Connect and test an instrument for measuring blood pressure.
Identify the operation and blood pressure monitor.
Connect to a column of mercury next to a graduate scale.
Determine of systolic and diastolic blood pressure by increase
and gradually reduce the pressure in the cuff.
Perform and operate the BP machine/ sphygmomanometers.
Construct and test of stethoscope.
10. Verify characteristics of Plan work in compliance with standard safety norms.
electronics, power Construct and test the transistor based switching circuits.
electronics and Special Construct and test CB, CE & CC amplifier circuit.
Semiconductors circuits. Ascertain the performance of different oscillator circuits.
(ELE/N9454) Measure the resistance, voltage, current through electronic
circuit using multimeter.
Construct and test of JFET amplifiers, oscillators and multi
vibrators.
Construct and test a UJT as relaxation Oscillator.
Construct and test lamp dimmer using TRIAC/DIAC.
Construct and MOSFET, IGBT test circuit and apply for suitable
operation with proper safety.
Construct and test a circuit using photo diode and verify its
characteristics.
11. Test various Medical gas Check Mechanical Ventilation, Refrigeration, Air conditioning.
plant operation using Test Air curtains, Laminar Flow Systems.
15
suitable care and safety. Apply safety and care of Refrigeration systems and Air
(ELE/N9455) conditioning systems.
Maintain Medical Gas pipe lines, Gas generators etc.
12. Test and operate different Identify short wave Diathermy Principles.
types of Physiotherapy Check Micro Wave Diathermy Principles.
Equipment's technique Identify different types of Electrodes used in Physiotherapy
and general care. Equipments.
(ELE/N9456) Check Preparation Equipments, Patient Positioning and
Application Techniques.
Take General Care of Transducers / Sensors and Equipments.
13. Assemble, test and Illustrate to practice the digital trainer kit with safety.
troubleshoot various Identify various digital ICs, test IC using digital IC tester and
digital circuits. verify the truth table.
(ELE/N7202) Construct and verify the truth table of all gates using NOR and
NAND gates.
Construct an adder cum subtractor circuits and verify the truth
table.
Construct a decoder and encoder, multiplexer and de-
multiplexer circuits and verify the truth table.
Construct a multiplexer and de-multiplexer and verify the truth
table.
Construct and verify the truth table of various flip flop, counter
and shift register circuits.
14. Construct, test and verify Ascertain and select tools and instruments for carrying out the
the input/output jobs.
characteristics of various Plan and work in compliance with standard safety norms.
analog circuits. Practice on soldering components on lug board with safety.
(ELE/N7202) Identify the passive /active components by visual appearance,
code number and test for their condition.
Construct and test the transistor based switching circuit.
Construct and test CB, CE & CC amplifier circuit.
Ascertain the performance of different oscillator circuits.
Construct and test clipper, clamper and Schmitt trigger circuit.
15. Demonstrate the Explain the roles of the main components and features of a cell
significance of different to the cell’s functions.
parts in the organization Analyze the benefits of cells combining together to form tissues
in the human body (Basics with specifications.
of Human Anatomy and Description the roles of organ and the interrelationships
Physiology). (ELE/N9457) between body system.
16. Execute the operation of Ascertain and select tools, material for the job and make this
different Bio Medical available for use in the timely manner.
sensors, identify, wire & Plan work in compliance with safety norms.
test various sensors by Demonstrate possible solution and agree task within the team.
16
selecting appropriate test Identify sensors used in process industries such as RTDs,
instruments. (ELE/N9458) Temperature ICs, Thermocouples, proximity switches (inductive,
capacitive and photo electric), load cells, strain gauge. LVDT by
their appearance.
Measure temperature of a lit fire using a Thermocouple and
record the readings referring to data chart.
Measure temperature of a lit fire using RTD and record the
readings referring to data chart.
Measure the DC voltage of Sensor & Transducers
Detect different objectives using capacitive, inductive and
photoelectric proximity sensors.
17. Construct and test Demonstrate analog trainer kit with safety precautions.
different circuits using ICs Identify various ICs, differentiate by code No. and test for their
741 operational amplifiers condition.
& ICs 555 linear integrated Construct and test various OPAMP circuits.
circuits and execute the Construct and test R-2R ladder type digital to analog converter
result. (ELE/N9459) circuit.
Construct and test different configurations of 555 IC e.g. astable,
monostable, bi-astable and VCO circuits.
18. Identify the working Identify Cell Counters Principles.

principles, Operation, Check Spectrophotometer Principles.
general care of Clinical Lab Identify Colorimeter Principles.
Equipments. (ELE/N9460) Identify transducers in Analytical Instruments.
Illustrate operation of Instruments.
Take general Care of Equipments.
19. Read and apply Read & interpret the information on drawings and apply in
engineering drawing for executing practical work.
different application in the Read &analyze the specification to ascertain the material
field of work. requirement, tools and assembly/maintenance parameters.
Encounter drawings with missing/unspecified key information
and make own calculations to fill in missing
dimension/parameters to carry out the work.
20. Demonstrate basic Solve different mathematical problems

mathematical concept and
principles to perform
practical operations.
Understand and explain Explain concept of basic science related to the field of study
basic science in the field
of study.
SECOND YEAR
21. Detect the faults and Identify the tools and equipments to perform the job with due
troubleshoot SMPS, UPS, care and safety.
17
and Inverter and Battery Dismantle the given stabilizer and find major sections/ ICs
charger. (ELE/N7202) components.
Identify various input and output sockets / connectors of the
given SMPS.
Identify major sections/ ICs/components of SMPS.
Identify and replace the faulty components and construct and
test IC Based DC-DC converter for different voltages.
Identify front panel control & indicators of UPS.
Identify various circuit boards in UPS and monitor voltages at
various test points.
Test UPS under Fault condition & rectify fault.
Identify the parts, trace the connection and test the DC
regulated power supply with safety.
Troubleshoot and service a DC regulated power supply
Test battery charger for its operation.
22. Prepare fibre optic setup Plan and select appropriate tools to complete the job safely.
and execute transmission Identify the resources and their need on the given fiber optic
and reception. trainer kit.
(ELE/N9461) Make optical fibre setup to transmit and receive analog and
digital data.
Demonstrate and apply FM modulation and demodulation using
OFC trainer kit using audio signal and voice link.
Demonstrate PWM modulation and demodulation using OFC
trainer kit using audio signal.
Demonstrate PPM modulation and demodulation using OFC
trainer kit using audio.
23. Install, test and maintain a Identify & use different tools and equipment used for
CCTV system and installation of CCTV, handle the tools with due care and safety.
configure the system for Identify the different CCTV components, Trace or follow the
surveillance function in CCTV setup for any commercial installation.
Hospital department. Identify the strategic locations for the installation of cameras.
(ELE/N4610) Plan and setup the procedure for switching the cameras to have
different views.
Identify the connectors and sockets used on DVRs, connect CCTV
Cameras to DVR, Record and Replay.
Dismantle DVR and identify major functional blocks and test for
the healthiness.
Make tools, machine tools, taste measure equipment and
technical equipment ready for operational use, check and
maintain such tools and equipment and initiate measures for the
rectify of errors.
Monitor, evaluate and check own work.
24. Identify, test, service & Interpret the procedure as per manual of Micro-processor 8085.
program 8085 Micro- Identity various ICs & their functions on the given Micro-
processor. (ELE/N9462) processor 8085 Kit.
18
Identify the address range of RAM & ROM.

Write data into RAM & observe its volatility.
Identify the port pins of the controller & configure the ports for
Input & Output operation.
Demonstrate entering of simple programs, execute & monitor
the results.
25. Demonstrate ICU Prepare of kidney chart and eye chart.

Department functions, Execute planning setup for ear chart and brain chart.
equipments etc., Calculate and analyze the internal heart chart rate.
calibration and basic Sketch blood circulating system.
human rating chart. Select and perform the techniques of skeletal system chart,
(ELE/N9463) respiratory system chart, nerve system chart and digestive
system chart.
Plan and prepare reproductive system chart.
Illustrate the bio medical engineering instrument calibration.
26. Interpret the factors, tools Interpret medical terminology quality, resolution, noise and
and techniques affecting speed.
the medical terminology Differentiate between the geometric factors affecting medical
image quality. terminology quality.
(ELE/N9464) Analyse the subject factors affecting medical terminology
quality.
Analyse the tools and technique available to create high quality
film.
Identify different types of equipments calibration procedure
and error measuring as per manual.
Conduct systematic troubleshooting.
27. Demonstrate the Recognize various principles of air conditioning and

functions of bio-medical Refrigeration, types of pumps and compressors, Principles of
Department. (ELE/N9465) operation.
Identify various elements of Intensive-Care Monitoring, Patient
monitoring displays.
Identify different Defibrillators, Pacemakers, EMG, EEG.
Check various monitors: Video monitors etc., Recorders: Strip
chart recorders, Galvanometric recorders, Ultraviolet recorders
and other recorders.
Operate ventilator identifying the physiology of respiratory
system.
Identify instrumentation for the mechanics of breathing,
Inhalators, Ventilators, Respirators, Humidifiers, Aspirators,
Electro Surgical diathermy.
28. Identify, test, service & Differentiate Microprocessor and Micro controller.
program Micro controller Identify architecture of 8051 family of Micro controllers, pin
8051. (ELE/N9467) diagram and various on chip resources.
Check various types of memory with 8051 such as On-chip,
19
external code memory, External RAM.

Prepare register Banks and use Memory mapping of the bit
addressable registers (bit memories).
Plan and prepare Instruction set and apply various types of
instructions.
Identify and select special function registers (SFRs) and their
configuration for various applications.
Check input / output ports and their configuration.
Implement various Timer and counting functions, aspects of
serial communication.
Utilize on-chip resources such as ADC etc.
Identify and select assembly software and compilers for 8051
Micro-controllers, 8052 and differentiate with 8051.
29. Demonstrate various Identify different components of Dental X-ray machine.

operations and functions Identify and check Collimator, Bucky Grids, Relays, contactors,
of Dental Chair & Dental Switches, Interlocking circuits.
X-Ray. (ELE/N9468)
30. Execute the operation of Identify, plan & prepare basic physics applications.
different of Imaging Prepare block diagram of Ultrasound scanner.
Equipments used in Apply transducer theory & various types. different modes i.e. A,
hospitals. (ELE/N9469) B, M- mode etc. Colour Doppler Ultrasound scanners
Analyze the basic physics subject factors affecting X-Ray.
Identify different components of X-ray machine,
Plan and prepare block diagram of X-ray machine, H.T.
Generator etc.
Identify X-ray tubes, scattered radiation and Secondary radiation
controls.
Identify and check digital X-ray concepts, X-ray films, Screens,
Darkroom system & Procedure, Collimator, Bucky Grids, Relays,
contactors, Switches, Interlocking circuits.
31. Recognize development of Identify role of Biomedical Engineer

a Bio-medical Department Record maintenance of Bio-Medical Department
in a hospital. (ELE/N9470) Get acquainted with NBEA license (National Biomedical
Engineers Association. MCEBTI. Bangalore, Biomedical engineers
should have NTC in Trade Medical Electronics under MIS NCVT).
Get accustomed with different types of License required for
Hospitals, NABH (National accreditation Board for Hospitals and
Healthcare), AERB (Atomic Energy Regulatory Board), ARRT
(American Registry Radiologic Technologists), Drug License,
RMDC (Registered Diagnostic Medical Sonographers), PC - PNDT
(Pre Conception and Pre-Natal Diagnostic Techniques).
32. Read and apply Read & interpret the information on drawings and apply in
engineering drawing for executing practical work.
different application in the Read &analyze the specification to ascertain the material
field of work. requirement, tools and assembly/maintenance parameters.
20
Encounter drawings with missing/unspecified key information

and make own calculations to fill in missing
dimension/parameters to carry out the work.
33. Demonstrate basic Solve different mathematical problems

mathematical concept and Explain concept of basic science related to the field of study
principles to perform
practical operations.
Understand and explain
basic science in the field
of study.
21
7. TRADE SYLLABUS
SYLLABUS - TECHNICIAN MEDICAL ELECTRONICS
FIRST YEAR
Professional Skills
Reference Learning Professional Knowledge
Duration (Trade Practical)
Outcome (Trade Theory)
With Indicative Hours
Professional Plan and execute Trade and Orientation EM Trade and its applicability
Skill 50 Hrs; soldering and de 1. Visit to various sections of in industries. Expectations of
Professional soldering of various the institute and identify the Industry from trainees
Knowledge electrical components location of various after the completion of the
14 Hrs like Lug’s, tag’s, clips, installations. (05 hrs) Trade.
Eyelets & Plugs for 2. Identify safety signs for The skills to be acquired to
electronic circuits danger, warning, caution & become part of industry.
following safety personal safety message. Intro to Safety and measures
precautions. (Mapped (03 hrs) to be taken to maintain the
NOS: ELE/N0102) 3. Use of personal protective standards of safety of
equipment (PPE). (04 hrs) personnel working and the
4. Practice elementary first equipment.
aid. (03 hrs) Different First aid mechanisms
5. Preventive measures for to rescue the effected by
electrical accidents & steps electric shocks or any physical
to be taken in such injuries.
accidents. (02 hrs) Classification of cables
6. Practice elementary on according to gauge, core size,
Artificial Respiration. (03 insulation strength, flexibility
hrs) etc.
7. Use of Fire extinguishers. (07 hrs)
(05 hrs)
8. Practice soldering on Different type of soldering
different electronics guns, relate temperature with
components Lug’s, Tag’s, wattage's, types of tips. Solder
Clips, Eyelets and Plugs. materials and their grading.
(03 hrs) Use of wax and other
9. Practice De soldering using materials.
pump and wick. (02 hrs) Selection of a soldering gun for
10. Identify and use Lug’s, specific requirement. Soldering
Tag’s, Clips, Eyelets and and De-soldering stations and
Plugs used in electronics their specifications. (07 hrs)
industries. (04 hrs)
11. Identify different types of
passive electronic
components. (02 hrs)
12. Practice soldering on
combinational circuits in
different values of
resistance. (02 hrs)
22
13. Identify resistors by their

appearance and check
physical defects. (03 hrs)
14. Practice De soldering the
same circuit using pump
and wick. (03 hrs)
15. Wire up the consumers
main board with ICDP
switch and distribution
fuse box. (03 hrs)
16. Prepare and mount the
energy meter board. (03
hrs)
Professional Plan, estimate, 17. Practice fixing of screws of Basic terms such as electric
Skill 25 Hrs; assemble, install and different sizes on wooden charges, Potential difference,
Professional test wiring system in board. (02 hrs) Voltage, Current, Resistance.
Knowledge hospital & CSSD 18. Identify various conduits Basics of AC & DC. Terms such
07 Hrs department. and different electrical as +ve cycle, -ve cycle,
(Mapped NOS: accessories. (02 hrs) Frequency, Time period, RMS,
ELE/N9447) 19. Practice cutting, threading Peak, P-P, instantaneous value.
of different sizes and Insulators, conductors and
laying installations. (05 semiconductor properties,
hrs) Single phase and Three phase
20. Prepare test power, Terms like Line and
boards/extension boards Phase voltage/ currents.
and mount accessories like Working principle of PMMC
lamp holders, various type ammeter. Conversion of
switches indicator, ammeter into voltmeter.
sockets, fuse, MCB’s etc. Working principles and study
(09 hrs) of Block diagrams / Schematic
21. Test and check rating of diagrams of Analog
different type of switches, Multimeter. Working principles
sockets, fuse and MCB’s. and study of Block diagrams /
(07 hrs) Schematic diagrams of Digital
Multimeter. (07 hrs)
Professional Identify, install, test 22. Install electrical line 110 V. Different type of electrical
Skill 25 Hrs; and operate different (02 hrs) cables and their specifications.
Professional photo therapy 23. Install and test using light Different types of Cables used
Knowledge equipments in fitting with reflector for in the electronic industries.
07 Hrs Biomedical Sector. direct and indirect lighting. Different types of Cables used
(Mapped NOS: (06 hrs) in the electronic industries.
ELE/N9448) 24. Test and identify different Ohm’s law and its variables.
groups wattage of lamps in Different types of UVB,
series for specified voltage. Halogen, Tube lights, UV,
(04 hrs) Lights, IR lights, CFL Photo
25. Practice installation of Therapy
various lamps e.g. Working principles and study
fluorescent tube, Tub of Block diagrams / Schematic
light/CFL etc. (05 hrs) diagrams of Digital LCR meter.
23
26. Identify different types of (07 hrs)

analog & digital
multimeters parts, its
function and operation.
(04 hrs)
27. Practice on various analog
and digital measuring
instruments. (02 hrs)
28. Practice on measuring
instruments in single and
three phase circuits. (02
hrs)
Professional Plan, carry out 29. Wire up the consumers Overload Relay, Fuse ratings,
Skill 50 Hrs; installation, fault main board with ICDP types of Fuses, Fuse bases,
Professional detection and switch and distribution single/three phase MCB’s,
Knowledge repairing of Hospital house box. (06 hrs) single phase ELCB’ s.
15 Hrs Electrical appliances. 30. Estimate the cost/bill of Phase angle, phase relations,
(Mapped NOS: material for wiring of active and reactive power,
ELE/N9449) hostel/ residential building power factor and its
and workshop. (07 hrs) importance in the industry.
31. Practice wiring of hospital Three phase Transformers and
building as per IE rules. (05 their Types of Contractors,
hrs) contactor coils and working
32. Practice on wiring of UPS voltages (08 hrs)
and inverter diagram,
test/fault detection of
domestic and industrial
wiring installation and
repair. (07 hrs)
33. Wire up the OPD, general contactor contact currents,
ward and ICU main board protection to contactor s and
with ICDP switch and high current applications
distribution fuse box. (03 (07 hrs)
hrs)
34. Estimate the cost/bill of
material for wiring of OPD,
general ward and ICU. (03
hrs)
35. Practice wiring diagram of
OPD as per IE rules. (03
hrs)
general ward as per IE
rules. (03 hrs)
ICU as per IE rules. (03 hrs)
minor OT as per IE rules.
(03 hrs)
24
39. Install various light fitting

with reflectors for direct
and indirect lighting of OT.
(03 hrs)
40. Practice test/fault
detection of minor OT and
OT wiring installation and
repair. (04 hrs)
Professional Test and service 41. Identify the rated various Battery /Cells: construction,
Skill 25 Hrs; different batteries types of cells output types of primary and
Professional used in electronics voltage and Ah capacity of secondary cells, materials used
Knowledge applications and given battery. (03 hrs) specification of cells and
07 Hrs record the data to 42. Practice on grouping of batteries.
estimate the repair cells for specified voltage Charging process, efficiency,
cost. and current under shelf life, Selection of cells /
(Mapped NOS: different conditions and Batteries etc
ELE/N9450) care. (02 hrs) Use of Hydrometer. Types of
43. Measure the specific electrolytes used in cells and
gravity of the electrolyte batteries.
using hydrometer. (03 hrs) propagation delay, power
44. Practice on routine, dissipation and noise immunity
care/maintenance and (07 hrs)
testing of batteries. (03
hrs)
45. Measure the resister value
by colour code and verify
the same by measuring
with multimeter. (02 hrs)
46. Identify the different type
of passive components
with colour code SMD and
DIP package. (02 hrs)
47. Identify the different type
of active components of
SMD and DIP package. (02
hrs)
transformers and test. (02
hrs)
49. Verify terminals, identify
HT and LT side and
calculate transformation
ratio of single phase
transformers. (02 hrs)
50. Determine voltage
regulation of single phase
transformer at different
loads. (02 hrs)
25
auto transformers and

test. (02 hrs)
Professional Operate and test 52. Dismantle and assemble Introduction, Balances, Hot
Skill 100 Hrs; clinical equipment/ electrical/electronic parts plate and Magnetic Stirrer
Professional instruments used in of various electronic Centrifuges, Hot air
Knowledge hospital. appliances e.g. Iron box, oven, Incubator, Water bath,
15 Hrs (Mapped NOS: Radiant warmer, Auto Nebulizer
ELE/N9451) cutoff multi coil, nebulizer, Construction & Testing of
AC & DC motor. (05 hrs) Baby / clinical Incubator,
53. Service and repair of Radiant warmer
electrical/electronic irons. Construction & Testing of
(05 hrs) Baby / clinical Incubator,
54. Prepare and test of silicon Construction & Testing of
pipe sealer. (05 hrs) Radiant warmer
55. Measure and test of Electrical motors: AC Motor
clinical sterilizer. (05 hrs) (single phase induction motor)
56. Practice testing/fault construction, sub assemblies,
detection of autoclave type of winding used,
(with & without auto cut interpretation of name plate
off multi coil). (07 hrs) specifications
57. Plan and prepare of Conventional speed control
incubator. (05 hrs) methods. Types of AC motors
58. Service and repair of and their applications.
radiant warmer. (05 hrs) Starting of split phase motor
59. Prepare and mount for and three phases AC motors.
setup baby clinical DC Motor construction, sub
incubator. (05 hrs) assemblies, carbon brushes
60. Prepare and mount the interpretation of name plate
proper nebulizer. (05 hrs) Specifications, conventional
61. Identify different terminals speed control methods and
and parts of electrical applications. Types of DC
wiring diagram for water motors and their applications.
pump with auto controller. (15 hrs)
(08 hrs)
62. Identify parts and
terminals of different
types of single phase AC
motors. (05 hrs)
63. Install, connect and
determine performance of
single phase AC motors.
(05 hrs)
64. Identify parts and
terminals of different
types of single phase DC
motors. (05 hrs)
single phase DC motors.
26
(05 hrs)
66. Connect, set proper
direction of rotation and
run. (05 hrs)
67. Identify and test
permanent magnet DC
motor. (05 hrs)
68. Identify and test brush less
DC motor. (05 hrs)
69. Service and repair of mixer
and fan. (05 hrs)
centrifuge. (05 hrs)
Professional Identify, place, solder, 71. Practice soldering on PCB design making,
Skill 25 Hrs; desolder and test different electronics Identification of 2/3/4 terminal
Professional different SMD discrete components, IC bases and SMD components. Soldering /
Knowledge components and IC PCB’s. (01 hr) de soldering of above
07 Hrs packages with due 72. Practice desoldering using components.
care and following pump and wick. (01 hr) Interpretation of diode
safety norms using 73. Join the broken PCB track specifications Forward current
proper tools/setup. and test. (02 hrs) and Reverse voltage, Packing
(Mapped NOS: 74. Identification of 2,3,4 styles of diodes.
ELE/N7812) terminal SMD Semiconductor component
components. (01 hr) number coding for different
75. Desolder the SMD electronic components such as
components from the Diodes, Zeners, Transistors,
given PCB. (03 hrs) FETs, MOSFETs, IGBTs. PN
76. Solder the SMD Junction, Forward and Reverse
components in the same biasing of diodes (07 hrs)
PCB. (03 hrs)
77. Check for cold continuity
of PCB. (03 hrs)
78. Identify various
connections and setup
required for SMD soldering
station. (03 hrs)
Si & Ge diodes and their
specifications. (02 hrs)
80. Measure the voltage and
current through a diode
in a circuit and verify its
forward characteristics.
(03 hrs)
81. Measure the voltage
and current through a
Zener diode in a circuit
and verify its forward
27
characteristics. (03 hrs)
Professional Assemble simple 82. Operate different Diode Bridge Modules.

Skill 25 Hrs; electronics power controls on the CRO front Rectifier configurations, their
Professional supply circuit and test panel and observe the efficiency, Filter components
Knowledge for functioning. function of each control. and their role in reducing
07 Hrs (Mapped NOS: (04 hrs) ripple +ve Voltage Regulator , -
ELE/N9452) 83. Measure DC voltage, AC ve Voltage Regulator
voltage, time period Specifications & block diagram
using CRO sine wave of Linear power supplies.
parameters. (04 hrs) Front panel controls and
84. Construct and test a half features of various power
wave, full wave and supplies.
bridge rectifier circuit Different types of power
with and without filter. switches and heat sinks used in
(04 hrs) power supplies. Manual &
85. Construct and test automatic and servo voltage
voltage doubler’s, stabilizers-concept and block
tripler’s and quadruple’s. diagram, o/p voltage
(04 hrs) adjustment, voltage cutoff
86. Test different regulated systems, study of different
power supply and types of relays used in
measure output voltage stabilizers, study of electronic
with load. (04 hrs) circuit commonly used, buck
87. Measure ripple voltage, and boost concept. (07 hrs)
ripple frequency and
ripple factor of rectifiers
for different load and
filter capacitors. (05 hrs)
Professional Execute testing; 88. Identify terminals verify Sphygmomanometer:
Skill 25 Hrs; evaluate performance the rubber cuff which is Names, Types (manual and
Professional and maintenance of apply to the arms. (04 digital), Operation, significance
Knowledge sphygmomanometers. hrs) (07 hrs)
07 Hrs (Mapped NOS: 89. Construct and test
ELE/N9453) sphygmomanometer for
measuring blood
pressure. (04 hrs)
90. Execute planning setup
for blood pressure
monitor examination. (05
hrs)
91. Determine the thermal
effect of electric current.
(03 hrs)
92. Measure and test of
stethoscope. (04 hrs)
93. Construct and test of BP
operator/
Sphygmomanometers.
28
(05 hrs)
Professional Verify characteristics 94. Identify different types of Transistor biasing circuits and
Skill 75 Hrs; of electronics, power transistors and their stabilization techniques.
Professional electronics and specification. (04 hrs) Voltage amplifiers- voltage
Knowledge Special 95. Measure the voltage and gain, loading effect.
15 Hrs Semiconductors current of different types configuration of common
circuits. of transistors in a circuit emitter configuration of
(Mapped NOS: and verify its common base their definition
ELE/N9454) characteristics and characteristics and application
measure Alpha, Beta and Configuration of common
Gama. (06 hrs) collector transistor their
96. Construct and test fixed definition characteristics and
bias, ammeter bias and application,
voltage divider bias of a Construction, Working of a
transistor amplifier PNP and NPN Transistors.
circuit. (05 hrs) Purpose of E, B & C Terminals.
97. Identify different types of Flow of currents into and out
photo diodes, tunnel of terminals of PNP/ NPN
diodes, variactor diodes Transistors and their relations
and lascer diodes and Significance of β of a
their specifications. (04 Transistor. Methods of
hrs) coupling.
98. Measure the voltage and CE ,CB,CC amplifier circuit and
current through a photo their characteristics Alpha
diode in a circuit and ,beta, voltage gain
verify its characteristics. Construction of FET,
(04 hrs) differentiate it with BJT.
99. Construct a circuit to Purpose of Gate Drain and
switch a lamp load using source terminals and
photo diode. (03 hrs) voltage/current relations
100. Measure the voltage and between them. Amplification
current through a tunnel factor of FET. Need for Biasing
diode in a circuit and of Transistor junctions
verify its characteristics. Interpretation of main
(05 hrs) parameters of a Transistor, VBE,
101. Measure the voltage and VCB,VCE, IC, IB, Junction
current through a Temperature,
variactor diode in a Impedance between various
circuit and verify its terminals
characteristics. (04 hrs) Interpret the main parameters
102. Measure the voltage and of the FET. Suitability of FET
current through a LASCR amplifiers in measuring device
diode in a circuit and applications
verify its characteristics. Working of power electronic
(04 hrs) components such as SCR,
103. Identify different types of TRIAC, DIAC, UJT, MOSFET and
DIAC, TRIAC, SCR, SCS, IGBT junction capacitance,
SBS & SUS and their Frequency of operation,
29
specification. (05 hrs) Discuss a Transistor application

104. Measure the voltage and as a switch. Discuss a
current through DIAC & Transistor application as an
TRIAC in different circuits amplifier, Define input
and verify its impedance and output
characteristics. (04 hrs) impedance amplifier.
105. Measure the voltage and configuration of common
current through SCR & collector transistor their
SCS in different circuit definition characteristics and
and verify its application
characteristics. (04 hrs) Classification of amplifiers
106. Measure the voltage and according to frequency, mode
current through SBS & of operation, Distinguish
SUS in different circuits between voltage and power
and verify its amplifier
characteristics. (04 hrs) Types and effect of negative
107. Identify Different types of feedback in amplifiers
UJT, PUT, FET, IGBT, GTO Working of emitter follower
and MOSFET. (05 hrs) circuit and its advantages
108. Measure the voltage and different packages styles of
current through UJT & transistors, in-circuit testing of
PUT in different circuits transistor (15 hrs)
and verify its
current through FET &
IGBT in different circuits
and verify its
current through GTO &
MOSFET in different
circuits and verify its
Professional Test various Medical 111. Identify the different gas Introduction to safety
Skill 25 Hrs; gas plant operation plant safety precaution precaution for different gas
Professional using suitable care while working. (04 hrs) plants,
Knowledge and safety. 112. Measure & Test of Hospital Oxygen o2 gas plant,
03 Hrs (Mapped NOS: Hospital Oxygen o2 gas Hospital nitrous (n2o) plant.
ELE/N9455) plant. (10 hrs) Hospital Gas Plant Layout (03
113. Construct & Test of hrs)
Hospital nitrous (n2o)
plant. (11 hrs)
Professional Test and operate 114. Identify different types of Electric stimulation of Nerve &
Skill 25 Hrs; different types of diathermy and their Muscle, Faradic-type current,
Professional Physiotherapy system. (04 hrs) Interrupted, Direct current,
Knowledge Equipment's 115. Operate & Test of shot Iontophoresis, TNS or TENS,
04 Hrs technique and general wave diathermy. (10 hrs) IFT, Methods of heating the
care. 116. Operate & Test of micro tissues, Diathermy, Infra-Red
30
(Mapped NOS: wave diathermy. (11 hrs) radiation, LASER, Ultrasonic.

ELE/N9456) Therapy, Ultra-violet Radiation,
Cold therapy, Mechanics (04
hrs)
Professional Assemble, test and 117. Familiarize digital IC’s. Difference between analog and
Skill 25 Hrs; troubleshoot various (02 hrs) digital signals, Iogic levels of
Professional digital circuits. 118. Identify different Logic TTL and CMOS
Knowledge (Mapped NOS: Gates (AND, OR, NAND, Introduction to Digital
07 Hrs ELE/N7202) NOR, EX-OR, EX-NOR, Electronics, Number systems
NOT ICs) by the number and codes
printed on them. (05 hrs) Digital code: binary, octal,
119. Verify the truth tables of Excess 3 code, grey code, BCD
all Logic Gate ICs by code, ASCII code and code
connecting switches and conversions, Logic Gates and
LEDs. (03 hrs) their truth tables,
120. Construct and verify the Study of a Digital IC Tester:
truth table of all the Specifications & Block diagram,
gates using NAND and Operation and circuit
NOR gates. (03 hrs) description of a Digital IC
121. Use digital IC tester to Tester, Logic families like
test the various digital TTL/CMOS and sub families
ICs (TTL and CMOS). (05 and their comparison.
hrs) Availability of logic gates in
122. Verify the switching multiple numbers in a package
circuits of all logic circuit with examples. Combinational
with the help of Boolean logic circuits such as AND-OR
equation. (02 hrs) Logic, AND-OR invert Logic s
123. Verify the Truth table for Universal property of NAND
De-Morgans first law and and NOR gates. Combinational
second law and from the logic circuits such as Half
result draw the logic Adder, Full adder, Parallel
gates. (05 hrs) Binary adders. IC 7482 as 2-bit
and four bit full adders.
Magnitude compactors. Half
adder, full adder ICs and their
applications for implementing
arithmetic operations (07 hrs)
Professional Construct, test and 124. Construct & Test RC RC coupled Amplifier (single &
Skill 25 Hrs; verify the coupled Amplifier by double stage), transformer
Professional input/output using single stage. (02 Coupled Amplifier, B Push pull
Knowledge characteristics of hrs) Amplifier, Audio Amplifier , FET
07 Hrs various analog 125. Construct & Test RC Common-source Low
circuits. coupled Amplifier using frequency amplifier, FET
(Mapped NOS: double stage. (03 hrs) Common-Drain Low frequency
ELE/N7202) 126. Construct & Test of amplifier
transformer Coupled
Amplifier. (05 hrs) Diode shunt and series clipper
127. Construct & Test of class circuits and clamping/limiting
B Push pull Amplifier. (05 circuits and their applications.
31
hrs) R C based Differentiator

128. Construct & Test Audio
Amplifier. (05 hrs) Transistor power ratings &
129. Construct & Test FET packaging styles, Use of
Common-source Low different heat sinks. (07 hrs)
frequency amplifier. (03
hrs)
130. Construct & Test FET
Common-Drain Low
frequency amplifier. (02
hrs)
Professional Demonstrate the 131. Identify Different parts of The human body cell is
Skill 30 Hrs; significance of the human Body. (04 hrs) comprised of several
Professional different parts in the 132. Identify the role of the organelles. Each has a specific
Knowledge organization in the main components and role in the life process of the
07 Hrs human body (Basics of features of the human cell. Some of these processes
Human Anatomy and body cell. (10 hrs) include respiration, protein
Physiology). 133. Outline the structure of synthesis and excretion.
(Mapped NOS: the main tissues of the
ELE/N9457) human body. (10 hrs) The human body comprises of
134. Identify the functions of four main tissues. Firstly, the
all the main organs of epithelial tissue has tightly
human body. (06 hrs) packed cells. These form
continuous sheets and act as
linings for different parts of the
body. These linings also help to
protect and separate the
organs. Epithelial tissue
functions on both the inside
and outside of the body. The
role in which this specific
tissue plays is that it acts as a
barrier from the outside
world's contaminants. These
tissues have many layers which
provide better protection,
meaning if one layer is lost, the
underlying layer is still
protected.
Explain the functions of all the
main organs found within the
body (07 hrs)
Professional Execute the operation 135. Test biomedical sensors. Bio potential Electrodes, Bio
Skill 65 Hrs; of different Bio (47 hrs) chemical electrodes & Other
Professional Medical sensors, 136. Measure temperature of electrodes. Cells and their
Knowledge identify, wire & test a lit fire using a Structure, Bio-electric
07 Hrs various sensors by Thermmeter and record potentials, Sources of Bio-
selecting appropriate the readings referring to electric, potentials, Resting &
test instruments. data chart. (08 hrs). Action potentials
32
(Mapped NOS: 137. Identify different types of Study different IC Packages IR

ELE/N9458) Electrodes. (04 hrs) LEDS, Photo diode for photo
138. Identify the electrodes transistor, its characteristics
used in medical devices. and application, optical sensor,
(06 hrs). opto-couplers, circuits with
opto isolation, characteristics
of LASER diodes.
Biomedical Sensors, Types,
classification, construction
details, measurement output,
signals of biomedical sensors.
(07 Hrs.).
Professional Construct and test 139. Construct & Test by using Types of multi-vibrators and
Skill 120 Hrs; different circuits using IC 741 op-amp. (04 hrs) study of circuit diagrams Time
Professional ICs 741 operational 140. Construct & Test Mono constants of RC & RL circuits.,
Knowledge amplifiers & ICs 555 stable Multi-vibrator by Block diagram of 555,
15 Hrs linear integrated using IC 555. (05 hrs) functional description w.r.t.
circuits and execute 141. Construct & Test Bi different configurations of 555
the result. stable Multi-vibrator monostable block diagram of
(Mapped NOS: using IC 555. (04 hrs) 555, functional description
ELE/N9459) 142. Construct & Test of VCO w.r.t. different configurations
(V to F converter) using of 555 monostable functional
IC 555. (05 hrs) description wrt different
143. Construct and test configurations of 555
Schmitt trigger using IC monostable functional
555. (04 hrs) description wrt different
144. Construct and test Ramp configurations of 555 astable
generator using IC 555. functional description wrt
(04 hrs) different configurations of 555
145. Construct and test time VCO operations for various
delay relay using IC 555. application, introduction to
(05 hrs) positive feedback and
146. Construct and test water requisites of an oscillator (07
level controller using IC hrs)
555. (05 hrs)
147. Construct and test 555
timers as pulse width
modulator. (05 hrs)
148. Pin Identification of OP- Study of a Linear IC Tester
Amp LM741, TLC274C, Integrator circuits,
LF356, LM324. (04 hrs) Introduction to Differential
149. Construct & Test of amplifier: construction &
Inverting Amplifier using working block diagram of Op-
Op –Amp. (04 hrs) Amp, Importance,
150. Construction & Testing of characteristics, common-mode
Non-Inverting Amplifier gain, advantages and
using Op –Amp. (04 hrs) applications. schematic
151. Construct & Test of diagram of 741, symbol, Non-
Summing Amplifier using inverting voltage amplifier,
33
Op –Amp. (05 hrs) inverting voltage amplifier, ,

152. Construction & Testing of linear and non-linear
Differential Amplifier applications of 741,
using Op –Amp. (05 hrs) Comparater using op-amp,
153. Construct & Test of other popular op-amps, Bio-
Logarithmic Amplifier medical Instrumentation
using Op –Amp. (04 hrs) Amplifier using Op -Amp, RC
154. Construct & Test of Low - Phase-shift Oscillator using ,
Pass Filter using Op – Wien Bridge Oscillator using
Amp. (04 hrs) Op-Amp, voltage to current
155. Construct & Test of High converter using Op-Amp,
- Pass Filter using Op – current to voltage converter
Amp. (04 hrs) using Op-Amp, Peak Detector
156. Construct & Test of Band using Op-Amp, Precision
- Pass Filter using Op – Rectifier using Op-Amp,
Amp. (04 hrs) Triangular & Square Wave
157. Construction & Testing of Generator using Op-Amp (08
RC Phase-shift Oscillator hrs)
using Op-Amp. (04 hrs)
158. Construct & Test of Wien
Bridge Oscillator using
Op-Amp. (04 hrs)
159. Construct & Test of
voltage to current
converter using Op-Amp.
(04 hrs)
160. Construct & Test current
to voltage converter
using Op-Am. (04 hrs)
161. Construct & Test Peak
Detector using Op-Amp.
(08 hrs)
162. Construct & Test
Precision Rectifier using
Op-Amp. (05 hrs)
163. Construct & Test Bio-
medical Instrumentation
Amplifier using Op –Amp.
(06 hrs)
164. Construct & Test Basic
Triangular & Square
Wave Generator using
Op-Amp. (06 hrs).
Professional Identify the working 165. Identify various ABD kits Microscope, Colorimeter and
Skill 100 Hrs; principles, Operation, peripherals and connect Spectrophotometer (Both VIS
Professional general care of Clinical it to the system of Blood & UV), Laboratory tests based
Knowledge Lab Equipments. Group using. (06 hrs) on Colorimeter and
13 Hrs (Mapped NOS: 166. Perform and execute PH Photometry, Flame
ELE/N9460) Meter. (05 hrs) photometry, Electrophoresis,
34
167. Understand how to Densitometry, Ph meters, Semi

prepare and measure auto analyzers, Blood, cell
calorimeter digital / counter, Blood gas analyzer.
analog. (06 hrs) (13 hrs)
168. Practically understand
how to use
Spectrophotometer. (06
hrs)
169. Practice and perform
sugar testing using Quick
check (TECO). (07 hrs)
170. Practice and perform the
method of patient care
and handling Semi Auto
Analyzer. (10 hrs)
171. Perform how to calculate
Blood Cell counter. (15
hrs)
172. Practically understand
how to measure uro
meter. (15 hrs)
173. Select and perform the
appropriate syringe
Destroyer & syringe
Pump. (15 hrs)
174. Prepare the room
apparatus and
instrument for electro
surgical Unit (surgical cut
and coagulation). (15 hrs)
ENGINEERING DRAWING: (40 Hrs.)
Professional Read and apply Introduction to Engineering Drawing and Drawing Instrument –
Knowledge engineering drawing (02 Hrs.)
ED-40 Hrs. for different  Conventions
application in the field  Sizes and layout of drawing sheets
of work.  Title Block, its position and content
 Drawing Instrument
Free hand drawing of –(06 Hrs.)
 Geometrical figures and blocks with dimension
 Transferring measurement from the given object to the free
hand sketches.
 Free hand drawing of hand tools.
Drawing of Geometrical figures: (04 Hrs.)
 Angle, Triangle, Circle, Rectangle, Square, Parallelogram.
 Lettering & Numbering – Single Stroke
Symbolic representation – (04 Hrs.)
 Different Electronic symbols used in the related trades
Reading of Electronic Circuit Diagram. (14 Hrs.)
Reading of Electronic Layout drawing. (10 Hrs.)
35
WORKSHOP CALCULATION & SCIENCE: (36 Hrs)

Professional Demonstrate basic Unit, Fractions (04 Hrs.)
Knowledge mathematical concept Classification of unit system Fundamental and Derived units
and principles to F.P.S, C.G.S, M.K.S and SI units Measurement units and
ED-40 Hrs. perform practical conversion. Factors, HCF, LCM and problems. Fractions -
WCS-36 Hrs. operations. Addition, substraction, multiplication & division. Decimal
Understand and fractions - Addition, subtraction, multiplication & division.
explain basic science Solving problems by using calculator.
in the field of study. Square root, Ratio and Proportions, Percentage (06 Hrs.)
Square and suare root. Simple problems using calculator.
Applications of pythagoras theorem and related problems. Ratio
and proportion.
Ratio and proportion - Direct and indirect proportions
Percentage
Percentage - Changing percentage to decimal and fraction.
Material Science (04 Hrs.)
Types metals, types of ferrous and non ferrous metals
Introduction of iron and cast iron
Mass, Weight, Volume and Density (02 Hrs.)
Specific gravity
Heat & Temperature and Pressure (04 Hrs.)
Concept of heat and temperature, effects of heat, difference
between heat and temperature, boiling point & melting point of
different metals and non-metals.
Scales of temperature, celsius, fahrenheit, kelvin and conversion
between scales of temperature.
Basic Electricity (12 Hrs.)
Introduction and uses of electricity, molecule, atom, how
electricity is produced, electric current AC,DC their comparison,
voltage, resistance and their units Conductor, insulator, types of
connections - series and parallel. Ohm's law, relation between
V.I.R & related problems. Electrical power, energy and their
units, calculation with assignments. Magnetic induction, self and
mutual inductance and EMF generation Electrical power, HP,
energy and units of electrical energy
Trigonometry (04 Hrs.)
Measurement of angles Trigonometrical ratios Trigonometrical
tables
Project work/Industrial visit
Broad areas:
a) Construct and test of four bit synchronous binary counter using IC 74163.
b) Construct and test bidirectional shift resistor.
c) Construct and test instrumentation amplifier.
d) Construct and test R-2R ladder type digital to analog converters circuit.
e) Construct and test a class B complementary push pull amplifier.
36
SYLLABUS - TECHNICIAN MEDICAL ELECTRONICS

SECOND YEAR
Professional Skills
Reference Learning Professional Knowledge
Duration (Trade Practical)
Outcome (Trade Theory)
With Indicative Hours
Professional Detect the faults and 175. Identify various input and Electrical wiring for Single
Skill 40 Hrs; troubleshoot SMPS, output phase and Three phase
Professional UPS and Inverter and sockets/connectors systems, Earthing and earth
Knowledge Battery charger. /indicators on the given resistance measurement.
10 Hrs (Mapped NOS: UPS. (04 hrs) Calculation of load power and
ELE/N7202) 176. Make individual power factor of a power
connections between source. Review on Batteries –
batteries of battery stack various types, their selection,
and test for healthiness grouping of cells and batteries,
of batteries on stack. (04 charging of batteries. Various
hrs) Battery charging circuits used
177. Connect battery stack to in Inverters and UPS,
the UPS. (04 hrs) Maintenance of Batteries
178. Make load test to Inverter – their principle &
measure backup time. operation, power rating,
(04 hrs) change over period
179. Identify isolator Installation of Inverters,
transformer, inverting Protection circuits used in
transformer and control inverters– battery level, over
transformers. (04 hrs) load, over charging etc.
180. Adjust charging current Various faults and its
according to number of rectification. Types of UPS.
batteries. (04 hrs) Block diagram and working
181. Identify various circuit principle of different types
boards and monitor UPS. Specifications of a typical
voltages at vital test UPS. Most frequently
points. (04 hrs) occurring faults and their
182. Identify the charging remedies. Concept of UPS, OFF
section and set the LINE and ONLINE. Difference
charging current between Inverters and UPS.
according to backup. Selection of UPS – calculation
Perform a load test to of load power, Line interactive
UPS. (04 hrs) UPS, ON- Line UPS, their
183. Identify the circuit description and
semiconductor power working- controlling circuits,
modules and measure Micro controller circuits,
voltages. (04 hrs) power circuits, charging
184. Maintain, Service and circuits, alarm circuits,
troubleshoot Battery Indicator circuits. (10 hrs)
charger and UPS. (04 hrs)
Professional Prepare fibre optic 185. Cutting, cleaning and Intro to optical fiber as a
Skill 50 Hrs; setup and execute preparing of fibre cable transmission media, its
Professional transmission and for splicing. (10 hrs) advantages over other media.
37
Knowledge reception. 186. Splicing of OFC using Working principle of

10 Hrs (Mapped NOS: splicing machine. Testing transmitter and receiver in
ELE/N9461) of OFC using OTDR. (15 fiber optic communication.
hrs) Application and advantages of
187. Measure propagation, fiber optic communication
return and bending properties of optic fiber,
losses etc. (10 hrs) testing, losses , types of fiber
188. Measure optical signal optic cables and specifications,
power using optical Fiber optic Encoding of light,
power meter. (05 hrs) Fiber optic joints, splicing,
189. Test the optical fibre testing and the related
cable using Visual Fault equipment s /measuring tools,
locator. (05 hrs) precautions to be taken, laying
190. Make optical fibre setup of cables, safety aspects while
to transmit and receive handling optical cables. (10
analog. (05 hrs) hrs)
Professional Install, test and 191. Identify different CCTV Introduction of CCTV,
Skill 50 Hrs; maintain a CCTV components. (05 hrs) computer hardware,
Professional system and configure 192. Draw, trace or follow the software’s installation,
Knowledge the system for CCTV setup of any multiple frame split in digital
10 Hrs surveillance function commercial installation. TV, restore old memories,
in Hospital (05 hrs) format new & old hard disk.
department. 193. Identify the strategic (10 hrs)
(Mapped NOS: locations for the
ELE/N4610) installation of camera.
(04 hrs)
indicators, cables,
connectors and ports on
the computer cabinet.
(04 hrs)
195. Demonstrate various
parts of the system unit
and motherboard
components. (04 hrs)
computer peripherals
and connect it to the
system. (04 hrs)
197. Install a Printer driver
software and test for
print outs (04 hrs)
198. Install antivirus software,
scan the system and
explore the options in
the antivirus software.
(04 hrs)
199. Install MS office
software. (04 hrs)
38
200. Connect network

connectivity for backup
recovery. (04 hrs)
201. Prepare multiple frame
split. (04 hrs)
202. Identify LCD Display
module and its
decoder/driver ICs (04
hrs)
Professional Identify, test, service 203. Identify various ICs & Draw schematic diagrams for
Skill 100 Hrs; & program 8085 their functions on the Microprocessor, Draw
Professional Micro-processor. given Microprocessor Kit. schematic diagrams for Micro-
Knowledge (Mapped NOS: (08 hrs) controller based circuits.,
15 Hrs ELE/N9462) 204. Measure the wave forms Intro to 8085 Microprocessor,
on different ICs and IC Architecture,
pins of the processor. (07 pin details and Bus System of
hrs) the processor
205. Monitor the clock Function of different ICs such
frequency. (07 hrs) as decoders
206. Write down the address Function of different ICs such
range of different as buffers,
memory ICs and latches etc used with 8085
peripheral ICs on the kit. processor Interfacing to
(08 hrs) memory ICs RAM, PROM /
207. Enter data to different EEPROM
memory locations in Interfacing different
RAM. (10 hrs) peripheral ICs such as 8255.
208. Enter simple programs Instruction set covering data
and execute using transfer, logical,
assembly language. (10 Instruction set covering data
hrs) transfer, Arithmetic.
209. Use assembler to Instruction set covering data
assemble the programs transfer, serial communication
and load them for etc. (15 hrs)
execution by the
processor. (10 hrs)
210. Use assembler to load
them for execution by
the processor. (15 hrs)
211. Program to Blink an LED
using port pins of 8255.
(08 hrs)
212. Program to Control a
relay using the port pins
of 8255. (10 hrs)
213. Program to read the data
from memory to
sequentially ON the
LEDs. (07 hrs)
39
Professional Demonstrate ICU 214. Plan and prepare of kidney chart, eye chart, ear
Skill 50 Hrs; Department functions, Kidney chart, eye chart, chart, Brain chart, working of
Professional equipments etc., ear chart, Brain chart. (15 heart chart, blood circulatory
Knowledge calibration and basic hrs) system, skeletal system chart,
15 Hrs human rating chart. 215. Identify the internal respiratory system chart,
(Mapped NOS: procedure of heart chart, nerve system chart, digestive
ELE/N9463) blood circulatory system. system chart, reproductive
(10 hrs) system chart, History of Bio-
216. Practice and perform the medical Engineering
skeletal system chart, Instrumentation, Man
respiratory system chart, Instrumentation system. (15
nerve system chart, hrs)
digestive system chart.
(10 hrs)
217. Prepare reproductive
system chart. (15 hrs)
Professional Interpret the factors, 218. Perform how to calculate Physiological system of the
Skill 75 Hrs; tools and techniques Pulse Oximeter. (10 hrs) Body, Medical Terminology.
Professional affecting the medical 219. Perform how to prepare Various departments in
Knowledge terminology image a EMG. (10 hrs) Hospital Classification of
26 Hrs quality. 220. Practice and perform the Hospitals, Introduction to
(Mapped NOS: method of patient care anatomy, Human Physiology,
ELE/N9464) and handling ECG. (10 Electro-physiology, Multi-Para
hrs) monitor, Ultrasound Doppler,
221. Plan patient setup for fetal Monitor Pulse Oximeter.
EEG & ERG. (10 hrs) (26 hrs)
222. Perform techniques of
applications of Multi-
Para monitor. (10 hrs)
223. Plan and perform the
care of Ultrasound
Doppler equipments. (10
hrs)
224. Plan patient setup for
Fetal Monitor, Infusion
Pump & Syringe Pump.
(08 hrs)
225. Practice and perform the
method of patient care
and handling Endo scope
& Colonoscopy. (07 hrs)
Professional Demonstrate the 273. Identify & test of Pulse Elements of Intensive-Care
Skill 100 Hrs; functions of bio- Oximeter, EMG, ECG Monitoring,
Professional medical Department. different controls of the Patient monitoring displays,
Knowledge (Mapped NOS: related equipments. (10 Defibrillators, Pacemakers,
26 Hrs ELE/N9465) hrs) EMG, EEG,
274. Identify calibration Monitors: Video monitors,
procedure or measuring Recorders: Strip chart
and monitoring recorders, Galvanometric
40
instruments. (10 hrs) recorders, Ultraviolet

275. Demonstrate care of recorders, and other recorders
applicators used infusion Ventilator: The physiology of
pump & syringe pump. respiratory system,
(10 hrs) Instrumentation for the
276. Prepare the room, mechanics of breathing,
apparatus and Inhalators, Ventilators,
instrument for Respirators, Humidifiers,
Endoscope & Aspirators, Surgical diathermy.
Colonoscopy. (15 hrs) (26 hrs)
277. Troubleshooting &
Maintenance aspects.
(10 hrs)
278. Check the effect on image
due to variation in focal
object distance, object
field distance, exposer
angle. (15 hrs)
279. Identify the technical
aspect of quality
assurance. (15 hrs)
280. Check the quality
assurance of the related
equipments and its
benefits with respect to
visual assessment. (15
hrs)
Professional Identify, test, service 281. Identify various ICs & Differentiate Microprocessor
Skill 75 Hrs; & program Micro their functions on the and Micro controller,
Professional controller 8051. given Microcontroller Kit. Architecture of 8051 family of
Knowledge (Mapped NOS: (08 hrs) Micro controllers, pin diagram
20 Hrs ELE/N9466) 282. Identify the address and various on chip resources.
range of RAM & ROM. Types of memory with 8051
(07 hrs) such as On-chip, external code
283. Measure the crystal memory, External RAM
frequency, connect it to Register Banks and their use
the controller. (08 hrs) Memory mapping of the bit
284. Identify the port pins of addressable registers (bit
the controller & memories).
configure the ports for Instruction set and various
Input & Output types of instructions
operation. (07 hrs) Special function registers
285. Use 8051 (SFRs) and their configuration
microcontroller, connect for various applications.
8 LED to the port, blink Input / output ports and their
the LED with a switch. configuration.
(07 hrs) Implementation of various
286. Perform the initialization, Timer and counting functions,
load & turn on a LED with aspects of serial
41
delay using Timer. (08 communication,

hrs) Utilization of on-chip
287. Perform the use of a resources such as ADC etc.
Timer as an Event Assembly software and
counter to count external compilers for 8051 Micro-
events. (07 hrs) controllers.
288. Demonstrate entering of 8052 and its difference with
simple programs, 8051. (20 hrs)
execute & monitor the
results. (07 hrs)
289. Perform with 8051
microcontroller
assembling language
program, check the
reading of an input port
and sending the received
bytes to the output port
of the microcontroller,
used switches and LCD
for the input and output.
(10 hrs)
290. Write a program to use
on board ADC and
convert the analog
voltage signal into digital
value and store it
memory. (06 hrs)
Professional Demonstrate various 291. Operating & Different components of
Skill 75 Hrs; operations and maintenance of Dental Dental X-ray machine.
Professional functions of Dental chair with suction & air Collimator, Bucky Grids,
Knowledge Chair & Dental X-Ray. compressor. (15 hrs) Relays, contactors, Switches,
27 Hrs (Mapped NOS: 292. Dental x-ray clarification Interlocking circuits (27 hrs)
ELE/N9467) Intra oral Dental x-Ray &
Extra oral Dental x-ray.
(10 hrs)
293. Identification Dentist
handling tools. (10 hrs)
294. Basic level of Dental X ray
calibration. (10 hrs)
295. Assembling and
disassembling of chair &
compressor. (15 hrs)
296. Assembling and
disassembling of X-Ray
(15 hrs)
Professional Execute the operation 297. Identification of control Ultrasound scanners: Basic
Skill 150 Hrs; of different of Imaging Panel of Ultrasound physics, Block diagram of
Professional Equipments used in scanners. (06 hrs) Ultrasound scanner,
Knowledge hospitals. 298. Identification of Types Transducer theory & types,
42
55 Hrs (Mapped NOS: Probe of Ultrasound Ultrasound scanner,

ELE/N9468) scanners. (06 hrs) transducer theory & types,
299. Identification of Modes Different modes i.e. A, B, M-
imaging of Ultrasound mode etc. Colour Doppler
scanners. (06 hrs) Ultrasound scanners
300. Operating Process of
Ultrasound scanners. (06 X-Ray: Basic physics.
hrs) Different components of X-ray
301. Identification of control machine, Block diagram of X-
Panel of X-ray. (06 hrs) ray machine, H.T. Generator,
302. Identification & X-ray tubes, Scattered
difference In CR & DR. radiation & Secondary
(06 hrs) radiation controls, Digital X-
303. Identification & ray concepts, X-ray films,
difference In Manual Screens, Darkroom system &
process of x-Ray expose Procedure, Collimator, Bucky
& film Development. (06 Grids, Relays, contactors,
hrs) Switches, Interlocking circuits,
304. Calibration of X-ray Beam Dental X-ray machine.
and tube head. (06 hrs) CT Scanner, MRI,
305. Digital X-ray imaging mammography, Bronchoscope
process. (06 hrs) (55 hrs)
306. Identify General fault
finding of X-ray
Equipment's. (06 hrs)
307. Calibration of table
alignment. (06 hrs)
308. Identification of CT
scanner parts. (06 hrs)
309. Identification of CT
scanner control panel
parts. (06 hrs)
310. Digital Image conversion
of Ct scanner. (06 hrs)
311. General fault finding of
CT scanner. (06 hrs)
alignment. (06 hrs)
313. Identification of MRI
parts. (06 hrs)
314. Identification of MRI
control panel parts. (06
hrs)
of MRI. (06 hrs)
MRI. (06 hrs)
alignment. (06 hrs)
43
318. Identification of
mammography parts. (06
hrs)
mammography control
panel parts. (06 hrs)
of mammography. (06
hrs)
mammography. (03 hrs)
Bronchoscope
partsGeneral fault finding
of Bronchoscope. (03
hrs)
Professional Recognize 323. Identify the main role of Role of Biomedical Engineer,
Skill 75 Hrs; development of a Biomedical Engineer. (11 record maintenance of
Professional Bio-medical hrs) Department, NBEA license
Knowledge Department in a 324. Identify SOPs of (National Biomedical
26 Hrs hospital. Biomedical Departments. Engineers Association.
(Mapped NOS: (14 hrs) MCEBTI. Bangalore,
ELE/N9469) 325. Demonstrate preventive Biomedical engineers should
steps care for NABH. (10 have NTC in Trade Medical
hrs) Electronics under MIS NCVT)
326. Check the Insurance Introduction of different types
applied for related of License required for
Biomedical Instruments. Hospitals, NABH (National
(10 hrs) accreditation Board for
327. Check the certification Hospitals and Health care),
for radiations. (10 hrs) AERB (Atomic Energy
328. Check the certification Regulatory Board), ARRT
for registration. (10 hrs) (American Registry Radiologic
329. Check the certification Technologists), Drug License,
for related licensee for RMDC (Registered Diagnostic
biomedical equipment's. Medical Sonographers), PC -
(10 hrs) PNDT (Pre Conception and
Pre-Natal Diagnostic
Techniques). (26 hrs)
ENGINEERING DRAWING: (40 Hrs.)
Professional Read and apply  Reading of Electronics Sign and Symbols. (04 Hrs.)
Knowledge engineering drawing  Sketches of Electronics components. (06 Hrs.)
ED-40 Hrs. for different  Reading of Electronics wiring diagram and Layout diagram.
application in the field (06 Hrs.)
of work.  Drawing of Electronics circuit diagram. (12 Hrs.)
Drawing of Block diagram of Instruments & equipment of
trades. (12 Hrs.)
WORKSHOP CALCULATION & SCIENCE: (20 Hrs)
Professional Demonstrate basic Algebra, (08 Hrs.)
44
Knowledge mathematical concept Addition, Subtraction, Multiplication & Divisions.

WCS-20 Hrs. and principles to Algebra – Theory of indices, Algebraic formula, related
perform practical problems.
operations. Estimation and Costing (12 Hrs.)
Understand and Simple estimation of the requirement of material etc., as
explain basic science applicable to the trade.
in the field of study. Problems on estimation and costing.
Project Work/ Industrial Visit
Broad areas:
a. Draw and identify & test of pulse oxymeter, EMG, ECG different controls of related equipments.
b. Identify various ICs and their functions on the given microcontroller kit.
c. Write a programme to use on board ADC and converter the analog voltage signal into digital
value and store it memory.
d. List the defect and symptom in the faulty SMPS.
e. Connect battery and load to UPS and test to measure backup time of battery.
45
SYLLABUS FOR CORE SKILLS

1. Employability Skills (Common for all CTS trades) (120Hrs + 60 Hrs)
Learning outcomes, assessment criteria, syllabus and Tool List of Core Skills subjects which
is common for a group of trades, provided separately inwww.bharatskills.gov.in/ dgt.gov.in
46
ANNEXURE-I
LIST OF TOOLS & EQUIPMENT

TECHNICIAN MEDICAL ELECTRONICS (For batch of 24 Candidates)
S No. Name of the Tools and Equipment Specification Quantity
A. TRAINEES TOOL KIT (For each additional unit trainees tool kit Sl. 1-12 is required additionally)
1. Connecting screwdriver 100 mm 25 nos.
2. Neon tester 500 V. 25 nos.
3. Screw driver set set of 5 25 nos.
4. Insulated combination pliers 150 mm 25 nos.
5. Insulated side cutting pliers 150 mm 25 nos.
6. Long nose pliers 150 mm 25 nos.
7. Soldering iron 25 W. 240 V. 25 nos.
8. Electrician knife 25 nos.
9. Tweezers 100mm 25 nos.
10. Digital Multimeter 25 nos.
11. Soldering Iron Changeable bits 15 W 25 nos.
12. De- soldering pump 25 nos.
B. SHOP TOOLS, INSTRUMENTS – For 2 (1+1) units no additional items are required
13. Fire extinguisher Operate and test clinical 1 no.
equipment/ instruments
used in hospital.
14. First aid kit 1 no.
15. Artificial Respiration Chart 2 nos.
16. Rubber mat - 180x45x2.5 cm 3 nos.
17. Rubber gloves pair 1 set
18. Steel ruler 30 cm 12 nos.
19. Scriber 15 to 20 cm 4 nos.

20. Center Punch 10 cm 4 nos.
21. Hammer cross pane 110 cm with handle 4 nos.
22. Hammer ball pane 220 cm with handle 4 nos.
23. Spanners double ended (metric 6mm to 19mm by 1.6mm 4 sets
system)
24. Spanners single ended 6mm to 25mm by 1.0m 2 sets
25. Box spanner set of (4-15) mm 1 set
26. Mallet 8 oz 2 nos.
27. Saw tenon 25 cm 2 nos.
28. Chisel wood 15cm set of 6mmto 25mm 2 sets
47
29. Chisel cold flat 10mm 2 nos.

30. Ratchet brace drill 10mm 2 nos.
31. Electric drill 10mm 2 nos.
32. Hacksaw 20-25cm (adjustable) 4 nos.
33. Junior saw 20cm 2 nos.

34. File flat 20cm 2nd cut 4 nos.
35. File flat 15 cm bastard 4 nos.
36. File half round 20cm bastard 4 nos.
37. File round 20cm 2nd cut 4 nos.
38. Instrument files (needle) set of 12 2 nos.
39. Vice bench 10cm jaw 2 nos.
40. Vice bench 5cm jaw 2 nos.
41. Taps set 3mm to 10mm (set of 9) 2 nos.
42. Dies set 3mm to 10mm 2 nos.
43. Grinder bench electric 1 no.
44. Soldering iron 25 Watt 12 nos.
45. Soldering iron 10 Watt 12 nos.
46. Temperature controlled soldering 15 Watt 2 nos.
station
47. De-soldering pump 2 nos.
48. Wire gauge set 2 nos.
49. Feeler gauge 2 nos.
50. Permanent bar magnet 15 cm 2 nos.
51. Solenoid with core 2 nos.
52. Electric bells 4 nos.
53. Battery eliminator 8 nos.
54. Batter storage lead acid 2 nos.
55. Hydrometer 2 nos.
56. Rheostats asserted values and 12 nos.
ratings
57. Variable resistors/Potentiometer 12 nos.
58. Fractional H.P. AC meters 2 nos.
59. Fractional H.P. DC meters 2 nos.
60. Constant voltage transformer/Auto 4 nos.
61. Auto Coil winding m/c. (manual) 1 nos.
62. D.C./A.C. Ammeter 0-1mA 4 nos.
67. Digital multi-meter 12 nos.
68. Thermo-couple meter R.F. 0-100mA 1 no.
48
69. Thermo-couple meter R.F. 0-500mA 1 no.

70. D.C/A.C. Voltmeter 0-5V 4 nos.
74. D.C/A.C. Voltmeter 0-5KV 2 nos.
75. Watt meter 5/250V 2 nos.
76. Insulation Tester 2 nos.
77. Service Oscillator 4 nos.
78. Signal tracer 4 nos.
79. A.F. Oscillator 4 nos.
80. Micro Wave Diatherrmy 1 no.
81. Ultra sonic diathermy 1 no.
82. ECG Recorder 2 nos.
83. Bed side monitor 2 nos.
84. Defibrillator 1 no.
85. Pace maker 2 nos.
86. 60mA Mobile x-ray equipment 1 no.
87. Dental x-ray equipment 1 no.
88. Dental Chair 1 no.
89. Portable Ultra sonic scanner (MOU) any hospital / 1 no.
Industries
90. Surgical diathermy 1 no.
91. Pulse Oximeter 1 no.
92. Operation Theater lighting system 2 nos.
93. Refrigerator 1 no.
94. Baby incubator 1 no.
95. Conductivity meter 2 nos.
96. Ventilators 1 no.
97. Simple sterilization equipment 4 nos.
98. U-V/ IR lamps 4 each
99. C.R.O ( 20 MHz) 5 nos.
100. Digital storage oscilloscope (20MHz) 1 no.
101. Function Generator 5 nos.
102. Power supply 0-30V/D.C. 2 nos.
103. Power supply 0-300V/D.C 2 nos.
104. Strain gauge with load cell 2 nos.
105. Allen Key set 2 nos.
106. SWG 2 nos.
107. Linear IC trainer 5 nos.
108. Personnel computer with latest CPU: 32/64 Bit i3/i5/i7 or 4 nos.
configuration latest processor, Speed: 3
GHz or Higher. RAM:-4 GB
DDR-III or Higher, Wi-Fi
49
Enabled. Network Card:

Integrated Gigabit Ethernet,
with USB Mouse, USB
Keyboard and Monitor
(Min. 17 Inch.) Licensed
Operating System and
Antivirus compatible with
trade related software.
109. Laser Printer 1 no.
110. Micro Processor Trainer 8085 (with 4 nos.
medical application card).
111. Microcontroller Trainer Kit 2 nos.
112. Digital I.C. trainer 4 nos.
113. Needle destroyer 1 no.
114. Infusion pump 1 no.
115. Syringe Pump 1 no.
116. Ultrasound Doppler 1 no.
117. X-Ray (MOU) any hospital / 1 no.
Industries
118. CT Scan (MOU) any hospital / 1 no.
Industries
119. MRI (MOU) any hospital / 1 no.
Industries
120. Dialysis (MOU) any hospital / 1 no.
Industries
121. Oxygen concentration 1 no.
122. CPAP 1 no.
123. BIPAP 1 no.
124. Nebulizer 1 no.
125. Flow meter 1 no.
126. Photo Therapy 1 no.
127. Radiant warmer 1 no.
128. Biolyes Operator 1 no.
129. OT Table Hydraulic 1 no.
130. ICU cot 1 no.
131. Phone cardiogram 1 no.
132. Traction machine T1 no.
133. Short wave Diathermy 1 no.
134. EMG 1 no.
135. TMT 1 no.
136. Logic Probes 4 nos.
137. Frequency counter 1 no.
50
138. A.F./R.F. Oscillator 2 nos.

139. Human body charts 2 nos.
140. Microscope 2 nos.
141. Analytical Balance 2 nos.
142. Centrifuge 2 nos.
143. Water Bath 1 no.
144. Hot air oven 2 nos.
145. Incubator 2 nos.
146. Spectrophotometer 1 no.
147. Colorimeter 1 no.
148. PH meter 2 nos.
149. Flame Photometer 1 no.
150. Blood gas analyzer (MOU) any hospital / 1 no.
Industries
151. Short Wave Diathermy 2 nos.
152. B.P. Apparatus (Sphygmo 4 no.
manometer)
153. Stethoscope 4 nos.
154. Wax bath 2 nos.
155. Muscle Stimulator 2 nos.
156. Suction apparatus 1 no.
157. Fetal monitor 1 no.
158. Refrigeration and Air conditioning 1 no. Each
Tutor
159. Air conditioners As Required
160. Earth leakage tester 1 no.
161. Blood cell counter 1 no.
162. DARK ROOM ACCESSORIES:
a) Film viewer (18" x 15") 1 no.
b) Cassettes (12" x 15", 10" x 12"and 10" 1 each
c) Safe light x 8") 1 no.
d) Set of tanks for 18 liters 1 set
capacity Stainless Steel
(12' x 15", 10" x 12" and 10"
(Master tank, Developer tank,
separator tank and Fixer tank.) x 8")
e) Hangers 1 each
f) Stainless steel clips 1 Dozen
g) Lead Apron 4' x 6' with lead glass 1 no.
h) Lead protection screen window 1 no.
163. Consumables
a. Electrical fuses -
Assorted/ different types
b. Thermal paper roll for
ECG recorder.
As required
c. Conductivity gel for ECG
isposable skin surface
electrodes.
d. Chemicals for pathology
lab
51
e. Medicated cotton.
Note: -
1. Internet facility is desired to be provided in the class room.
2. All the tools and equipment are to be procured as per BIS specification.
52
ABBREVIATIONS:
CTS Craftsmen Training Scheme

ATS Apprenticeship Training Scheme
CITS Craft Instructor Training Scheme
DGT Directorate General of Training
MSDE Ministry of Skill Development and Entrepreneurship
NTC National Trade Certificate
NAC National Apprenticeship Certificate
NCIC National Craft Instructor Certificate
LD Locomotor Disability
CP Cerebral Palsy
MD Multiple Disabilities
LV Low Vision
HH Hard of Hearing
ID Intellectual Disabilities
LC Leprosy Cured
SLD Specific Learning Disabilities
DW Dwarfism
MI Mental Illness
AA Acid Attack
PwD Person with disabilities
53
54

Tech. Medical Electronics CTS2.0 NSQF-4

Uploaded by

Copyright:

Available Formats

Tech. Medical Electronics CTS2.0 NSQF-4

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tech. Medical Electronics CTS2.0 NSQF-4

Uploaded by

Copyright:

Available Formats

GOVERNMENT OF INDIA

MINISTRY OF SKILL DEVELOPMENT & ENTREPRENEURSHIP

COMPETENCY BASED CURRICULUM

TECHNICIAN MEDICAL ELECTRONICS

SECTOR – ELECTRONICS AND HARDWARE

(Revised in Jul 2022)

CRAFTSMEN TRAINING SCHEME (CTS)

Ministry of Skill Development and Entrepreneurship

S No. Topics Page No.

8. Annexure I (List of Trade Tools & Equipment) 47

During the two-year duration of Technician Medical Electronics trade a candidate is

Directorate General of Training (DGT) under Ministry of Skill Development &

Trainee needs to demonstrate broadly that they are able to:

 Read & interpret technical parameters/documentation, plan and organize work

2.2 PROGRESSION PATHWAYS:

2.3 COURSE STRUCTURE:

Notional Training Hours

1 Professional Skill (Trade Practical) 840 840

Total 1200 1200

4 On the Job Training (OJT)/ Group Project 150 150

2.4 ASSESSMENT & CERTIFICATION

2.4.1 PASS REGULATION

2.4.2 ASSESSMENT GUIDELINE

Appropriate arrangements should be made to ensure that there will be no artificial

Assessment will be evidence based comprising some of the following:

 Job carried out in labs/workshop

Evidences and records of internal (Formative) assessments are to be preserved until

Performance Level Evidence

practices demanded by the component/job.

(b) Marks in the range of 75%-90% to be allotted during assessment

Bio-Medical Equipment Technician; Electronics Technician; Biomedical Engineering

Medical Equipment Technician; in the Healthcare Industry is also known as a Biomedical

Medical Laboratory Technician; (MLT) is also referred to as Clinical Laboratory Science

Medical Electronics Mechanic; Medical Electronic Equipment Mechanic repairs medical

Name of the Trade TECHNICIAN MEDICAL ELECTRONICS

Trade Code DGT/1070

NCO – 2015 3211.0200, 3211.0501, 3212.0701

Minimum Age 14 years as on first day of academic session.

Unit Strength (No. Of

(Must have studied English/ Communication Skills and Basic Computer

5.1 LEARNING OUTCOMES (TRADE SPECIFIC)

LEARNING OUTCOMES ASSESSMENT CRITERIA

Check the cold continuity, identify loose/dry solder and broken

18. Identify the working Identify Cell Counters Principles.

20. Demonstrate basic Solve different mathematical problems

Identify the address range of RAM & ROM.

25. Demonstrate ICU Prepare of kidney chart and eye chart.

27. Demonstrate the Recognize various principles of air conditioning and

external code memory, External RAM.

29. Demonstrate various Identify different components of Dental X-ray machine.

31. Recognize development of Identify role of Biomedical Engineer

Encounter drawings with missing/unspecified key information

33. Demonstrate basic Solve different mathematical problems

SYLLABUS - TECHNICIAN MEDICAL ELECTRONICS

13. Identify resistors by their

26. Identify different types of (07 hrs)

39. Install various light fitting

auto transformers and

characteristics. (03 hrs)

Professional Assemble simple 82. Operate different Diode Bridge Modules.