Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 3 views

    MCI - BENZIPOX COAL TAR EPOXY - TDS

    Uploaded by

    tarmidzi

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    MCI - BENZIPOX COAL TAR EPOXY - TDS

    Uploaded by

    tarmidzi
    3 views3 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    3 views3 pages

    MCI - BENZIPOX COAL TAR EPOXY - TDS

    Uploaded by

    tarmidzi

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 3

    TECHNICAL DATA SHEET (MCI-TDS-055, Rev2, 24.07.

    2024)

    BENZIPOX COAL TAR EPOXY


    Two Pack High Build Coal Tar Epoxy

    BENZIPOX COAL TAR EPOXY is a two pack high build coal tar epoxy coating designed for use as a high build protective system on both
    steel and concrete surfaces. It can be applied up to 200 microns or even thicker in one coat, thus eliminating potential inter-coat
    adhesion problem. It is intended for immersion and non-immersion services which require excellent protection against fresh and salt
    water, abrasion and splashes of corrosive chemicals. It is recommended to be used in aggressive environment including harbor shore
    installation, marine structure, jetty piles, ship bottom, sewage treatment plant, ballast tank, chemical plant and etc.

    Standard Packing : 5 litres & 15 litres

    Technical Information

    Mixing Ratio (By Volume) : 1 : 3 (Base : Hardener)


    Binder : Polyamide
    Finish : Soft Matt
    Color : Black, refer BENZi High Performance Coating color card
    Thinner : Thinner
    Solid Content : 85% (by weight); 78% (by volume)
    Dry Film Thickness : 125 - 300 microns / coat
    Theoretical Coverage : 6 m2 / litre / coat (DFT of 125 microns); 3 m2 / litre / coat (DFT of 300 microns)
    No. of coats : Minimum 2 coats
    Touch Dry @ 30°C : 1 - 2 hours (depends on temperature and humidity)
    Recoating Interval : Minimum 10 hours
    Curing Time @ 30°C : 4 - 5 days
    Pot Life @ 30°C : 2 - 3 hours after mixing of Base and Hardener
    Shelf Life : Minimum 12 months if properly stored

    Typical Painting System

    Substrate Primer (1 coat) Intermediate (1 coat) Topcoat (1 coat)

    Ferrous Metal * BENZIPOX Inorganic Zinc Rich Primer BENZIPOX Coal Tar Epoxy BENZIPOX Coal Tar Epoxy

    Concrete ** BENZIPOX Mastic 88 BENZIPOX Coal Tar Epoxy BENZIPOX Coal Tar Epoxy

    * Recommended to apply a mist coat dilution up to 30% of BENZIPOX Inorganic Zinc Rich Primer onto the substrate prior to full
    application of the same, as to avoid popping, blistering and delamination in service.
    ** Recommended to dilute the primer (BENZIPOX Mastic 88) with 30% Thinner as to provide better penetration and adhesion to
    concrete surface.

    Application Methods

    Brush / Roller : Recommended for small area and touch up such as stripe coating, weld-seams, edges, corner,
    rivets etc. Dilute up to 5% of Thinner if necessary.
    Conventional Air Spray : Dilute up to 10% of Thinner if necessary
    Airless Spray : If thicker coat in one application is required, airless spray application is recommended. Dilute
    up to 5% of Thinner if necessary
    Handling : Mix the Base and Hardener in correct ratio and stir the paint thoroughly until completely mixed
    before painting
    Clean Up : Clean all paint equipment with Thinner immediately after use

    1|Page
    TECHNICAL DATA SHEET (MCI-TDS-055, Rev2, 24.07.2024)

    BENZIPOX COAL TAR EPOXY


    Two Pack High Build Coal Tar Epoxy

    Surface Preparation

    Ferrous Metal Surface


    For optimum performance, mild steel surface shall be abrasively blasted in accordance to Swedish Standard Sa 2.5. If abrasive blasting
    is impossible, mechanical cleaning to St 3 is essential. If oxidation occurred on the blasted steel before application of paint, it is necessary
    to reblast the steel. The surface must be dry and free from any abrasive residues, dirt, grease and other contaminants prior to painting.

    Concrete Surface
    Newly laid concrete surface must be allowed to cure for at least 28 days, ensure the surface is below 16% moisture content as measured
    by protimeter and alkalinity below PH9. If alkalinity is high, neutralize the surface by etching with 5% Sulphuric Acid solution and rinsed
    thoroughly with clean water and allow to dry completely prior to painting.

    Storage

    Keep container tightly closed and in a secure upright position, store in a cool and shady place, do not expose directly to sunlight and
    extremes of temperature. Keep out of reach of children.

    Safety, Health and Environment

    Ensure good ventilation during painting, do not breathe vapour or spray mist. Keep doors and windows open during application and
    drying. It is advisable to wear mask and eyes protector while applying. In case of contact with eyes, rinse immediately with plenty of
    water and seek medical advice. In case of accidental ingestion, DO NOT INDUCE VOMITING, seek immediate medical advice. To remove
    splashes of paint from skin by using water and soap or skin care product. Do not empty paint into drains or water courses, dispose of
    any paint waste in accordance with the appropriate Environmental Quality Regulations.

    Materials Safety Data Sheet ( MSDS ) is available upon request.

    2|Page
    TECHNICAL DATA SHEET (MCI-TDS-055, Rev2, 24.07.2024)

    BENZIPOX COAL TAR EPOXY


    Two Pack High Build Coal Tar Epoxy

    Limitation of Liability

    Liability of MCI Paint Sdn Bhd on any claim of any kind, including claims based upon negligence of MCI Paint Sdn Bhd, for any loss or
    damage arising out of, connected with, or resulting from the use of the products, shall in no case exceed the purchase price allocable to
    the products or part thereof which give rise to the claim. In no event shall MCI Paint Sdn Bhd be liable for consequential or incidental
    damages.

    Disclaimer

    The above information is given to the best of our knowledge based on laboratory tests and practical experiences. However, since we
    cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the quality of the
    product itself. We reserve the right to change the given information without prior notice due to production refinements arising from
    continuing research and development, which may result in changes in the paint properties.

    MCI PAINT SDN BHD (849155-P)


    Lot 5189, Kawasan Perindustrian Balakong Jaya, 43300 Balakong, Selangor.
    Tel: +603 8962 2788 Fax: +603 8962 2798 Website: www.mcipaint.com.my

    3|Page

    You might also like