Bulletin 140U/Ue: Molded Case Circuit Breakers

TECHNICAL DATA
BULLETIN 140U/UE
Molded Case Circuit Breakers
CATALOG NUMBERS 140U/UE
Bulletin 140U/UE

Electrical Specifications
Standards Interrupting Ratings Rated Insulation Voltage Rated Impulse Withstand Voltage Rated Operational Voltage Permissible Ambient Temperature DC-Rated Short Circuit Breaking Capacity Utilization Category Power Loss 4 4 4 4 4 4 4 5 5
Auxiliary Circuit Specifications

Internal Control Module Terminations Auxiliary and Alarm Contacts Undervoltage Release Shunt Trips 5 5 6 6
Mechanical Specifications
Weight Dimensions Mounting Hardware Terminals, Lugs, and End Caps 7 7 7 7
Termination Specifications
G- & H-Frames J- & K-Frames L- & M-Frames N-Frame 8 10 12 14
Dimension Drawings
G-Frame H-Frame J-Frame K-Frame L-Frame M-Frame N-Frame 18 20 23 24 25 27 28
Visit our website: www.ab.com/catalogs
Bulletin 140U/UE

Time-Current Curves
G-Frame 100 A Thermal-Magnetic MCCBs H-Frame 125 A Thermal-Magnetic MCCBs J-Frame 250 A Thermal-Magnetic MCCBs J-Frame 250 A Electronic LS MCCBs J-Frame 250 A Electronic LSI MCCBs J-Frame 250 A Electronic LSG & LSIG MCCBs K-Frame 400 A Thermal-Magnetic MCCBs 35, 65 kA (-K3, -K6) 100 kA (-K0) K-Frame 400 A Electronic LS,LSG MCCBs 35, 65 kA (-K3, -K6) 100 kA (-K0) K-Frame 400 A Electronic LSI,LSIG MCCBs 35, 65 kA (-K3, -K6) 100 kA (-K0) K-Frame 400 A Electronic MCCBs with Ground Fault Protection L-Frame 600 UL (630 IEC) A Thermal-Magnetic MCCBs Q-Frame 600 A Thermal-Magnetic MCCBs 35, 65 kA (-Q3, -Q6) M-Frame 800 A Thermal-Magnetic MCCBs (300600 A) 50, 65 A (-M5, -M6) M-Frame 800 A Thermal-Magnetic MCCBs (700 & 800 A) 50, 65 A (-M5, -M6) M-Frame Electronic LS, LSG MCCBs 50, 65 A (-M5, -M6) M-Frame Electronic LSI, LSIG MCCBs 50, 65 A (-M5, -M6) M-Frame 800A Electronic MCCBs with Ground Fault Protection N-Frame Electronic LS MCCBs N-Frame Electronic LSI MCCBs N-Frame Electronic LSG, LSIG MCCBs with Ground Fault Protection 27 28 29 35 36 37 40 40 41 42 40 41 40 40 41 44 48 52 52 52 53 52 54 55 55 55 56 57 58 59 60
Bulletin 140U/UE
Bulletin 140U/UE
Bulletin 140U/UE

Electrical Specifications
Frame Size Interrupting Ratings Max Rated Current In Frame Ratings [A] [A] G 100 100 2, 3 2-3P 415 690 H 125 125 1, 2, 3 750 690 H (UE) 160 160 3, 4 750 690 J 250 250 3 750 690 K 400 400 3 750 690 L 600 600 3 750 690 L (UE) 630 630 3, 4 750 690 M 800 800 3 750 690 N 1200 800/1200 3 750 690
No. of Poles Main Poles Auxiliary Circuit Main Conductors Auxiliary Circuits IEC (50 Hz) [V] [V]
Rated Insulation Voltage (U) According to IEC 60947-2
Rated Impulse Withstand Voltage (Uimp) [kV] [kV] 2-3P 6 4 6 4 6 4 8 4 8 4 8 4 8 4 8 4 8 4
Rated Operational Voltage (Ue) - AC [V] 440 480 690 600/347 690 600/347 690 600 690 600 690 600 690 600 690 600 690 600 UL/NEMA (60 [V] Hz) UL 489 CSA 22.2 No. 5 IEC 60947-2
Standards Compliance Ambient Operating Temperature Range +16140F (8.960C) Permissible Ambient Temperature, Low Setting/High Setting Derating Factor (%) Molded Case Circuit Breaker At 40 C At 50 C At 55 C At 60 C At 70 C At 40 C At 50 C At 55 C At 60 C At 70 C 100 96 93 91 86 100 /100 96/92 93/87 91/83 86/73 100 100 96 81 86 100 /100 96/92 93/87 91/83 86/73 100 100 96 81 86 100/100 96/94 94/90 92/87 88/80 Isolation Switch 100 100 96 88 82 100 100 96 90 85 100 100 95 90 84 100 100 95 90 84 100 100 95 90 84 100 91 85 81 100/100 96/92 93/87 90/84 85/75 100/100 96/91 93/86 90/82 84/70 100/100 96/91 93/86 90/82 84/70 100/100 96/91 93/86 90/82 84/70 100 91 85 81
DC - Rated Short Circuit Breaking Capacity (kA) Time Constant < 8ms, non-inductive loads 1 Pole 2 Poles in Series 3 Poles in Series 250V 440V 660V 10 (2p) 10 20 20 10 20 20 10 20 20 10 20 20 10 20 20 10 20 30 10
Thermal set at max. on Fixed Thermal. Bulletin 140UE versions of the H-, J-, L-, M-, and N-Frame only comply with IEC 60947-2.
Bulletin 140U/UE

Electrical Specifications, Continued
Frame Size G Utlization Category Maximum Switching Ops/hour Frequency At maximum rated current (In), 3-Phase Symmetrical Load Molded Case Circuit Breaker Molded Case Switch [W] 50 50 75 175 250 87 87/210 H A 300 300 H (UE) A 300 J A 240 Power Loss K A 240 L A 240 L (UE) A 240 M A 60 N A 60
[W]
40
40
75
107
160
87
87/210
Auxiliary Circuit Specifications

Frame Size G with Terminal Connections - Cable Size Wire size range Lead Length Wire size range Tightening Torque AWG mm2 H H (UE) J K L L (UE) M N Internal Control Module Terminations
with Supplied Leads in. (cm) AWG mm2 Lb-in Nm 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4 48 (122) #18 0.82 7..12.4 0.8..1.4
Auxiliary & Alarm Contacts Rated Thermal Current - Ith Rated Making Capacities Rated Operational Current (AC15) 230V 400V 480V 690V Rated Operational Current (DC13) 24V 125V 240V [A] [A] [A] 5 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 6 0.5 0.15 [A] [A] [A] [A] 6 (240V) 0.25 (600V) 0.25 (600V) 0.25 0.25 0.25 0.25 0.25 0.25 6 3 6 3 6 3 6 3 6 3 6 3 6 3 6 3 [A] 6 6 6 6 6 6 6 6 6
[A]
10
20
20
20
20
20
20
20
20
Back-up Protection (max rating) Fuses Miniature Circuit Breakers [A] [A] 6 6 6/4/4 6/4 6/4/4 6/4/4 6/4/4 6/4 6/4/4 6/4 6/4/4 6/4 6/4/4 6/4 6/4/4 6/4 6/4/4 6/4
Bulletin 140U/UE

Auxiliary Circuit Specifications, Continued
Frame Size G Response Voltage Drop-out (CB trip) Pick-up (CB switch on) AC (50/60 Hz) 12V 24V 4860V 110127V 208240V 380500V 525600V DC 12V 24V 4860V 110125V 220250V Max. Operating Time Response Voltage Pick-up (CB Trip) AC (50/60 Hz) 24V 4860V 110240V 380440V 480600V DC 12V 24V 4860V 110125V 220250V Max. Operating Time [W] [W] [W] [W] [W] [ms] 50 29 120 475720 99121 50 29 120 475720 99121 50 164 631 8301580 112150 50 164 631 8301580 112150 4058 50 79 1000 1831 112150 50 79 1000 1831 112150 50 35 170 7101105 110140 4154 50 46 405 5894 7498 3849 62 [VA] [VA] [VA] [VA] [VA] 135500 10 139210 83360 4181080 10 139210 83360 4181080 87405 7101105 66432 127188 3460 87405 7101105 66432 127188 3460 87405 7101105 66432 127188 3460 87405 7101105 66432 127188 3460 200 8301280 100550 95136 4070 86631 4871 81505 4368 4169 [Us] 70110% 70110% 70110% 70110% 70110% 70110% 70110% 70110% 70110% [W] [W] [W] [W] [W] [ms] 50 0.88 0.7 1.121.76 0.941.21 1.451.86 50 0.88 0.7 1.121.76 0.941.21 1.451.86 50 1.6 3.1 2.03.1 1.62.2 3.14 50 Shunt Trips 1.6 3.1 2.03.1 1.62.2 3.14 50 1.6 3.1 2.03.1 1.62.2 3.14 50 1.6 3.1 2.03.1 1.62.2 3.14 50 1.6 3.1 2.03.1 1.62.2 3.14 50 2.6 3.6 3.55.5 2.93.6 4.86.3 80 [VA] [VA] [VA] [VA] [VA] [VA] [VA] 5.3 1.5 1.8 1.4 4.8 0.95 0.72 1.15 1.78 0..961.25 1.281.68 2.23.9 0.95 0.72 1.15 1.78 0..961.25 1.281.68 2.23.9 1.9 3.9 2.53.8 1.82.4 2.73.8 3.45.8 1.9 3.9 2.53.8 1.82.4 2.73.8 3.45.8 1.9 3.9 2.53.8 1.82.4 2.73.8 3.45.8 3.44.3 1.9 3.9 2.53.8 1.82.4 2.73.8 3.45.8 3.44.3 1.9 3.9 2.53.8 1.82.4 2.73.8 3.45.8 3.45.4 1.9 2.4 2.34.1 3.44.2 4.86.5 6.812.0 [Us] [Us] 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% 3570% 85110% H H (UE) J K L L (UE) M N Undervoltage Releases
Power Consumption
Power Consumption
Bulletin 140U/UE

Mechanical Specifications
Frame Size G [lb.] [kg] [lb.] [kg] [lb.] [kg] [lb.] [kg] Height 1-Pole Width Depth Height 2-Pole Width Depth Height 3-Pole Width Depth Height 4-Pole Width Depth Endurance Operating Cycles 1.5 0.7 2.2 1 4.88 (124.0) 2 (50.8) 2.81 (71.4) 4.88 (124.0) 3 (76.2) 2.81 (71.4) 10000 H 1.0 0.45 2.0 0.91 3.0 1.36 4.0 1.81 5.5 (139.7) 1 (25.4) 3 (76.2) 5.5 (139.7) 2 (50.8) 3 (76.2) 5.5 (139.7) 3 (76.2) 3 (76.2) 5.5 (139.7) 4 (101.6) 3 (76.2) 10000 H (UE) 1.0 0.45 2.0 0.91 3.0 1.36 0.0 5.5 (139.7) 1 (25.4) 3 (76.2) 5.5 (139.7) 2 (50.8) 3 (76.2) 5.5 (139.7) 3 (76.2) 3 (76.2) 5.5 (139.7) 4 (101.6) 3 (76.2) 10000 J Weight (approx.) 1-Pole 2-Pole 3-Pole 4-Pole 11.4 5.2 11.4 5.2 15.4 7 7 (177.8) 4.13 (105) 4.05 (103) 7 (177.8) 4.13 (105) 4.05 (103) 7 (177.8) 4.13 (105) 4.05 (103) 7 (177.8) 5.51 (140) 4.05 (103) 10000 Mounting Hardware Imperial (in.) Cat. No. Metric Cat. No. Quantity Style Tightening Torque Lb-in Nm 0.138-32 x 2.63 0.138-32 x 3.00 0.250-20 x 1.75 0.3125-18 x 3.9 0.3125-18 x 3.9 0.3125-18 x 1.25 140U-MMHS 0.3125-18 x 1.25 140U-N-MHS 13.4 6.1 16.1 7.3 10.16 (258) 5.51 (140) 4.09 (104) 10.16 (258) 7.2 (183) 4.09 (104) 10000 13.4 6.1 16.1 7.3 10.16 (258) 5.51 (140) 4.09 (104) 10.16 (258) 7.2 (183) 4.09 (104) 8000 13.4 6.1 16.1 7.3 10.16 (258) 5.51 (140) 4.09 (104) 10.16 (258) 7.2 (183) 4.09 (104) 8000 43.9 19.9 16 (406) 8.25 (210) 4.05 (103) 3000 46.9 21.3 62.3 28.3 15.98 (406) 8.27 (210) 4.09 (104) 15.98 (406) 11.02 (280) 4.09 (104) 3000 K L L (UE) M N
Dimensions in Inches (mm)
140U-G-MHS 140U-H-MHS
140U-K-MHS 140U-L-MHS 140U-L-MHS
M4 x 0.7 x 75 M4 0.7 x 75 M4 x 0.7 x 75 M4 x 0.7 x 90 M6 x 1.0 x 45 M5 x 0.8 x M5 x 0.8 x M8 x 1.0 x 35 M8 x 1.0 x 35 mm mm mm mm mm 100 mm 100 mm mm mm 140U-G140U-H140U-H140U-K140U-M140U-N140U-J-MHM 140U-L-MHM 140U-L-MHM MHM MHM MHM MHM MHM MHM 4 Pan Head 15 1.69 4 Pan Head 15 1.69 4 Pan Head 15 1.69 4 Pan Head 10 1.13 4 Pan Head 2025 23 4 Pan Head 25 3 4 Pan Head 25 3 4 Pan Head 28 3 4 Pan Head 28 3
Bulletin 140U/UE

Terminal and Lugs Specifications
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. Terminals Specification Material A Dim. B C Fastener Torque Lb-in Nm 1/2 (12.7) 3/8 (9.53) 1/8 (3.175) Specification Std/Optional Cat. No. Material Terminal Fastener Hardware Lb-in Nm Box Lugs Standard Steel Flathead 10 0.2 Cu Only 60/75C 1 1/2 12.7 #143 2.526 Slotted #8 40 lb-in. 10 mm 4.5 Nm #63 45 lb-in. 1626 mm 5.1 Nm Optional 140U-H-MTL3A Aluminum Lugs Multitap Optional 140U-H-MTL6A Aluminum
Frame Size
End Cap Optional 140UH-ECM Molded Housing
Slip on Terminal box lug Fastene r Torque
Cable Type Cable Temperature Rating Cable Quantity
Wire Strip Length Wire Range
in. mm AWG mm2
Terminal Type
B
Lb-in #1410 36 lb-in. Wire Torque Nm 2.56 mm 3.9 Nm
Material A B C D Fastener Lb-in Torque Nm 1/2 (12.7) 7/16 (10.99) 1/4 (6.35) 1/5 (5.0)
Std/Optional Cat. No. Material Terminal Fastener Hardware Lb-in Nm
Standard Steel
Dim.
Flathead
#10-32 Slotted Screw
#10-32 Slotted Screw
Flathea Terminal d Fastene 3550 r Torque 4.05. 6
10 0.2 Cu Only 60/75C (1) 1/2
45 lb-in 5 Nm Cu/Al 60/75C (3)
45 lb-in 5 Nm Cu/Al 60/75C (6)
Cable Type Cable Temperature Rating Cable Quantity Wire Strip Length in.
(A) (B) (C) 1(A) (B) (C) 13/81/ 3/47/ 1/41- 3/81/ 3/47/ 1/412 in. 8 in. 3/8 in. 2 in. 8 in. 3/8 in. (A) 913 mm #3 3/0 3595 (B) 1922 mm #14#2 2.535 Allen - 5/32 in. (4 mm) 50 5.6 70 lb-in 7.9 Nm (C) 3235 mm (A) 913 mm (B) 1922 mm #14#6 2.510 Allen - 3/32 in. (3 mm) 25 lb-in 2.8 Nm (C) 3235 mm
mm
D C
12.7 #141 0 #8 10 #64 1625
Allen - 4 mm 3438 Lb-in 3.84.3 Nm
Wire Range
B
AWG
mm2 2.56
Terminal Type Lb-in Nm 35 4.0
Slotted 40 4.5 45 5.1
Wire Torque
10
Bulletin 140U/UE

Terminal and Lugs Specifications, Continued
Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. Terminals Frame Size Specification Material A Dim. B C D Fastener Torque Lb-in Nm J
A
Lugs Specification Std/Optional 3/4(19.05) 5/8(15.88) Cat. No. Material Box Lugs Optional 140U-JTLS1 Steel Phillips Head 10 0.2 Cu Only 60/75C (1) 0.75 19.05 4350 MCM Allen 180 20 Optional 140U-KTLC1 Copper Optional 140U-JTLA1 Alumium Phillips head 10 0.2 Cu/Al 60/75C (1) 0.75 19.05 4350 MCM 25185 Allen 250 28 Optional 140U-KTLA1 Optional 140U-KTLA1A Optional 140U-KTLC2 Copper Mechanical Lugs Optional 140U-KTLA2 Alumium Optional 140U-KTLC1A Copper Optional 140U-KTLA2A Optional 140U-KTLA1B Optional 140U-KTLC1B Copper
5/16(7.94) Terminal Fastener Hardware 5/16(8.0) Hex 180/250 20/28 Terminal Fastener Torque Lb-in Nm
Cable Type Cable Temperature Rating Cable Quantity Wire Strip Length in. mm AWG
D C
Wire Range
B
mm2 25185 Lb-in Nm
Terminal Type Wire Torque
Material A Dim. B C D Fastener Torque Lb-in Nm 1(25.4) 3/4(19.05) 3/8(9.53) Hex 275/375 3/42
Std/Optional Cat. No. Material
Alumium Alumium
Alumium Alumium
Terminal Fastener Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hex 7/32 Hardware 11/32(8.9) Terminal Fastener Torque Lb-in Nm 96 10.8 Cu Only 60/75C (1) 1 25.4 96 10.8 Cu/Al 60/75C (1) 1 25.4 96 10.8 Cu/Al 60/75C (1) 1 25.4 96 10.8 Cu Only 60/75C (2) 1 25.4 96 10.8 Cu/Al 60/75C (2) 1 25.4 96 10.8 Cu Only 60/75C (1) 1 25.4 96 10.8 Cu/Al 60/75C (2) 1 25.4 96 10.8 Cu/Al 60/75C (1) 1 25.4 96 10.8 Cu Only 60/75C (1) 1 25.4
Cable Type Cable Temperature Rating Cable Quantity Wire Strip Length in. mm
K
A
AWG
D C
250 500
250 500
#3350 3/0250 3/0250
3350
Wire Range
B
2/0250 MCM (2) 50075 or 0 2/0500 (1) 70120 (2) or 70240 (1) 27537 5 31 or 42 30040 0 (1)
50075 0
mm2
120 240
120 240
30185
95120
95120
30185
Terminal Type Wire Torque Lb-in Nm
Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 Allen 3/8 375 42 375 42 275 31 275 31 275 31 275 31 550 62 550 62
11
Bulletin 140U/UE
Lugs Frame Size Specification Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque Lb-in Nm Optional 140U-J-MTL3A Aluminum 1/420 screw 50 lb-in 5.6 Nm Cu/Al 60/75C (3) (A) 3/81/2 in. (A) 913 mm (B) 3/47/8 in. (B) 1922 mm #14#2 2.525 Allen - 5/32 in. (4 mm) 70 lb-in 7.9 Nm Optional 140U-K-MTL3A Aluminum .375 x 25 screw 72 -96 lb-in 8.610.8 Nm Cu/Al 60/75C (3) (A) 9/16.3/4 (B) 1-3/16.1in. 1/2 in. (A) 1419 mm (B) 3038 mm #122/0 470 Allen - 3/16 in. (5 mm) 120 lb-in 13.5 Nm (C) 1-7/821/4 in. (C) 4857 mm (C) 1-1/413/8 in. (C) 3235 mm (6) (A) 3/81/2 in. (A) 913 mm (B) 3/47/8 in. (B) 1922 mm #14#6 2.510 Allen - 3/32 in. 25 lb-in 2.8 Nm Optional 140U-K-MTL6A Aluminum .375 x 25 screw 72 -96 lb-in 8.610.8 Nm Cu/Al 60/75C (6) (A) 9/16.3/4 (B) 1-3/16.1in. 1/2 in. (A) 1419 mm (B) 3038 mm #142 AWG 2.570 Allen - 1/8 in. (3 mm) 25 lb-in 2.8 Nm (C) 1-7/821/4 in. (C) 4857 mm (C) 1-1/413/8 in. (C) 3235 mm Multitap Optional 140U-J-MTL6A Aluminum 1/420 screw 50 lb-in 5.6 Nm Cu/Al 60/75C End Cap Optional 140U-J-ECM Molded Housing Allen - 4 mm 120144 Lbin 1416 Nm Optional 140U-K-ECM Molded Housing Allen - 8 mm 275 Lb-in 31 -m
Cable Type Cable Temperature Rating J Cable Quantity Wire Strip Length in. mm Wire Range AWG mm2
Terminal Type Wire Torque Lb-in Nm Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque Lb-in Nm
Cable Type Cable Temperature Rating K Cable Quantity Wire Strip Length in. mm AWG mm2 Lb-in Nm
Wire Range
12
Bulletin 140U/UE

Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. Frame Size Terminals Specification Material A B C D Fastener Torque L Lb-in Nm 1.0 (25.4) 15/16 (23.81) 1/2 (12.7) 33/64 (13.0) Slotted 42 3 Specification Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque Lb-in Nm Box Lugs 140U-LTL6A1 Aluminum 140U-LTL6C1 Copper 140U-LTL6A2 Aluminum 140U-LTL6C2 Copper 140U-LTL4A1 Aluminum 140U-LTL4C1 Copper Lugs Mechanical Lugs
Dim.
Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) 200 22 Cu/Al 60/75C (1) 1-1/8 29 500750 240380 550 62 Optional 140U-MTLC3 Copper Bolt (19 mm) 3035 200 22 Cu only 60/75C (1) 1-1/8 29 500750 240380 500 57 Optional 140U-MTLA2 Aluminum Bolt (19 mm) 3035 200 22 Cu/Al 60/75C (2) 1-1/8 29 2500 35240 375 42 Optional 140U-MTLC2 Copper Bolt (19 mm) 3035 200 22 Cu only 60/75C (2) 1-1/8 29 2500 35240 375 42 Optional 140U-MTLA3 Aluminum Bolt (19 mm) 3035 200 22 Cu/Al 60/75C (1) 1-1/8 29 2500 35240 375 42 Optional 140U-MTLA2A Aluminum Bolt (19 mm) 3035 200 22 Cu only 60/75C (1) 1-1/8 29 2500 35240 375 42 Optional
Cable Type Cable Temperature Rating
Cable Quantity Wire Strip Length in. mm AWG mm2 Lb-in Nm
D C
Wire Range
Terminal Type
B
Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm)
Wire Torque 1-1/16 (26.99) 17/8 (45) 1/2 (12.7) 1/2 (12.7) Socket 275/400 31.1/45.2
Material A Dim. B C D Fastener Torque M

A
Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque Cable Type Cable Temperature Rating Cable Quantity Wire Strip Length
D
ft-lb Nm
Lb-in Nm
40.547.5 40.547.5 40.547.5 40.547.5 40.547.5 Cu only 60/75C (3) 1-1/16 27 3/0300 95185 275 31 Cu/Al 60/75C (2) 1-1/16 27 1500 50240 375 42 Cu only 60/75C (2) 1-1/16 27 2/0500 70240 300 34 Cu/Al 60/75C (3) 1-1/16 27 3/0400 95185 375 42 Cu/Al 60/75C (2) 1-1/16 27 500750 95185 500 56
in. mm
Wire Range
B
AWG mm2 Lb-in Nm
Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm) Hex (8 mm)
13
Bulletin 140U/UE
Lugs Frame Size Specification Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque Lb-in Nm Optional (B) 3038 mm #122/0 470 Lb-in Nm (C) 1-7/821/4 in. (C) 4857 mm Multitap Optional (6) (A) 9/16.3/4 (B) 1-3/16.1in. 1/2 in. (A) 1419 mm (B) 3038 mm (C) 1-7/821/4 in. (C) 4857 mm End Cap Optional 140U-L-ECM Molded Housing Allen - 8 mm 200 Lb-in 22 Nm
Cable Type Cable Temperature Rating L Cable Quantity Wire Strip Length in. mm AWG mm2 Lb-in Nm
Wire Range
Std/Optional Cat. No. Material Terminal Fastener Hardware Terminal Fastener Torque
Cable Type Cable Temperature Rating M Cable Quantity Wire Strip Length in. mm Wire Range AWG mm2 Lb-in Nm
14
Bulletin 140U/UE

Dimensions are in inches (millimeters). Dimensions are not intended to be used for manufacturing purposes. Terminals Frame Size Specification Material A B Dim. C D Fastener Torque N Lb-in Nm 1-3/8 in. (35 mm) 1-1/2 in. (38 mm) 1/2 in. (12.7 mm) (2) 0.5x13 (12.7x1.75) Specification Std/Optional Cat. No. Material Optional 140U-NTLA3 Aluminum Optional 140U-NTLA2 Aluminum Lugs Mechanical Lugs Optional 140U-NTLC2 Copper Optional 140U-NTLA4 Aluminum Optional 140U-NTLC3 Copper Optional 140U-NTLC4 Copper
Terminal Fastener Hardware Terminal Fastener Torque Cable Type Cable Temperature Rating ft-lb
Bolt (19 mm) 3545
Bolt (19 mm) 3545 40.547.5 Cu/Al 60/75C (2) 1 25.4 #1500 MCM 50240 Hex (8 mm) 375 42
Bolt (19 mm) 3545 40.547.5 Cu Only 60/75C (2) 1 25.4 2/0500 MCM 70240 Hex (8 mm) 300 34
Bolt (19 mm) 3545 40.547.5 Cu/Al 60/75C (4) 1 25.4 4/0500 MCM 120240 Hex (8 mm) 375 34
Nm 40.547.5 Cu/Al 60/75C (3) in. mm AWG mm2 1 25.4 3/0400 MCM 95185 Hex (8 mm) 375 42
Cable Quantity Wire Strip Length
D C D
Wire Range
Terminal Type
B
Wire Torque
Lb-in Nm
15
Bulletin 140U/UE
Dimensions
G Frame
15-20 AMP, CLAMP AND BINDING SCREW TERMINALS

.84 [ 21,4 ] .16 [ 4,1 ]
25-100 AMP, PRESSURE COLLAR TERMINALS

.84 [ 21,4 ]
.49 [ 12,5 ]
2.00 [ 50,8 ] 1.00 [ 25,4 ] .97 [ 24,6 ]
.14 [ 3,6 ]
2.42 [ 61,5 ]
3.22 [ 81,8 ]
1.00 [ 25,4 ]
3.21 [ 81,5 ] .49 [ 12,4 ]
.16 [ 4]
1.22 [ 30,9 ]
1.22 [ 30,9 ]
16
Bulletin 140U/UE
Dimensions, Continued
.84 [ 21,3 ] .36 [ 9,1 ] .45 [ 11,4 ]
3.00 [ 76,2 ] 1.00 [ 25,4 ]
.16 [ 4,1 ]
3.21 [ 81,4 ]
4.88 [ 123,8 ]
140U G FRAME
3.22 [ 81,7 ]
1.00 [ 25,4 ]
1.00 [ 25,4 ]
2.41 [ 61,2 ]
.45 [ 11,4 ]
.36 [ 9,1 ] 2.83 [ 71,8 ]
1.22 [ 31 ]
140U G-FRAME
17
Bulletin 140U/UE
Molded Case Circuit Breakers Dimensions, Continued

H Frame
0.8524 (21.6509)
0.4179 (10.6146)
3.4141 (86.7181) 1.9730 (50.1142)
0.1680 (4.2672)
3.8120 (96.8248)
1.0070 (25.5778)
2.9725 (75.5015)
BUL 140U/UE J FRAME 2-POLE
18
Bulletin 140U/UE
.47 [ 11,9 ]
.88 [ 22,2 ]
.54 [ 13,6 ]
3.00 [ 76,2 ] 1.00 [ 25,4 ]
2.47 [ 62,7 ] .97 [ 24,6 ]
5.50 [ 139,7 ]
3.81 [ 96,9 ]
3.44 [ 87,4 ]
1.00 [ 25,4 ]
1.00 [ 25,4 ]
2.93 [ 74,3 ] .88 [ 22,4 ]
BUL 140U/UE H FRAME 3-POLE
19
Bulletin 140U/UE

4.00 2.00 1.00 1.00 1.00 3.00
.97
.97
5.50
3.81
3.81
5.50
4-POLE
3-POLE BUL 140U/UE H FRAME
20
Bulletin 140U/UE

J Frame
4.13 [ 104,8] 1.38 [ 34,9] .20 [ 5] 4.43 [ 112,4] 3.19 [ 81,1]
7.00 [ 177,8]
5.50 [ 139,7]
1.38 [ 34,9]
1.38 [ 34,9]
2.84 [ 72,2]
3-POLE 140U/UE J FRAME

.19 [ 4,8 ] 3.44 [ 87,3] .81 [ 20,6]
4.13 5.50 1.38
.78
7.00 7.00 5.50
4-POLE
3-POLE BUL 140U/UE J FRAME
21
Bulletin 140U/UE

K Frame
.95 [ 24,2 ]
1.48 [ 37,7 ]
5.49 [ 139,4 ] .63 [ 15,9 ] 1.72 [ 43,7 ]
.28 [ 7,1 ]
.84 [ 21,4 ]
1.19 [ 30,2 ]
10.13 [ 257,2 ]
8.88 [ 225,4 ] 8.44 [ 214,3 ]
1.72 [ 43,7 ]
1.72 [ 43,7 ] 4.86 [ 123,3 ]
4.06 [ 103,2 ]
1.43 [ 36,2 ]
1.06 [ 27]
1.01 [ 25,7 ]
140U K FRAME
22
Bulletin 140U/UE

L Frame
5.48 [ 139,2] 1.72 [ 43,6 ] .22 [ 5,5 ] 3.36 [ 85,3 ]
10.13 [ 257,2]
8.44 [ 214,4]
1.72 [ 43,7 ]
1.72 [ 43,7 ]
5.43 [ 137,9 ]
.25 [ 6,4 ] .97 [ 24,6] 1.34 [ 34,1]
140U/UE L FRAME 3-POLE
23
Bulletin 140U/UE
7.22 1.72 1.72
5.48
1.72
.84
.84
10.13
8.44
8.44
10.13
BUL 140U/UE L FRAME 4 POLE
24
Bulletin 140U/UE

M Frame
8.25 [ 209,6] 2.75 [ 69,9]
.38 [ 9,5 ]
.63 [ 15,9]
.74 [ 18,7]
16.00 [ 406,4]
14.75 [ 374,7]
.84 [ 21,4] 1.03 [ 26,2] 5.50 [ 139,6]
.84 [ 21,4]
1.87 [ 47,6]
1.03 [ 26,2]
BUL 140U/UE M FRAME
25
Bulletin 140U/UE

N Frame
8.25 [ 209,6] 2.75 [ 69,9]
2.75 [ 69,9]
.34 [ 8,7]
.63 [ 15,9]
5.19 [ 131,8]
16.00 [ 406,4]
14.75 [ 374,7]
5.50 [ 139,7] 7.18 [ 182,5]
5.50 [ 139,7]
3.84 [ 97,6] .97 [ 24,6] 1.09 [ 27,8]
140U/UE N FRAME
2.00 [ 50,8]
11.00 2.75 2.75 .63
8.25 2.75 .63
14.75 16.00 14.75 16.00
BUL 140U/UE N FRAME 4-POLE
26
Bulletin 140U/UE

Discrimination Short-circuit level to which discrimination is achieved.
Upstream (max. settings) "T" represents max. discrimination to kA rating level of the downstream device. Bulletin 140UE H-Frame 16 Breaker Rating (A) 16 20 32 Bulletin 140UE H-Frame MCCB 18 kA & 25 kA versions 40 50 63 80 100 125 160 16 20 32 Bulletin 140UE H-Frame MCCB 45 kA & 70 kA versions 40 50 63 80 100 125 50 63 Bulletin 140UE J-Frame MCCB 45 kA & 70 kA versions 80 100 125 160 200 250 Bulletin 140UE L-Frame MCCB 50 kA & 70 kA versions Bulletin 140UE N-Frame MCCB 50 kA & 70 kA versions 250 320 400 500 630 800 1250 1600 0.32 kA 0.2 kA 0.32 kA 0.2 kA 20 32 40 0.4 kA 0.4 kA 0.1 kA 0.4 kA 0.4 kA 0.1 kA 50 0.5 kA 0.5 kA 0.5 kA 0.8 kA 0.5 kA 0.5 kA 0.5 kA 0.8 kA 63 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 0.63 kA 80 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 0.8 kA 100 125 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1.3 kA 1 kA 160 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 50 80 18, 25, 40, or 70 kA version 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA 1 kA Bulletin 140UE J-Frame 100 125 160 200 250 45 or 70 kA version T T T T T T T T T T T T T T T T
10 kA 10 kA 10 kA 10 kA
10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 3 kA 3 kA 3 kA
40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 10 kA 1 kA 1.25 kA 1.25 kA 1.25 kA 10 kA 10 kA 10 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 1.6 kA 3 kA 2 kA 2 kA 2 kA 2 kA 2 kA 3 kA 3 kA 2.5 kA 2.5 kA 2.5 kA 2.5 kA 2.5 kA 2.5 kA
Downstream
27
Bulletin 140U/UE

Discrimination, Continued
Upstream (max. settings) "T" represents max. discrimination to kA rating level of the downstream device. Bulletin 140UE L-Frame 250 Breaker Rating (A) 16 20 Bulletin 140UE H-Frame MCCB 18 kA & 25 kA versions 32 40 50 63 80 100 125 160 16 20 Bulletin 140UE H-Frame MCCB 45 kA & 70 kA versions 32 40 50 63 80 100 125 50 63 Bulletin 140UE J-Frame MCCB 45 kA & 70 kA versions 80 100 125 160 200 250 Bulletin 140UE L-Frame MCCB 50 kA & 70 kA versions Bulletin 140UE N-Frame MCCB 50 kA & 70 kA versions 250 320 400 500 630 800 1250 1600 T T T T T T T T T T 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 26 kA T T T T T T T T T T 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 26 kA 320 400 50 or 70 kA versions T T T T T T T T T T 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 26 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA T T T T T T T T T T 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 26 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA T T T T T T T T T T 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 26 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA T T T T T T T T T T 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 22 kA 500 630 800 Bulletin 140UE N-Frame 1250 T T T T T T T T T T 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 22 kA 1600 T T T T T T T T T T 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 65 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA 22 kA 50, 70, or 100 kA versions
28
Downstream
Bulletin 140U/UE
Time-Current Curves
Bul.140U
Time-Current Curves for Bulletin 140U-G Thermal-Magnetic Molded Case Circuit Breakers
CURRENT IN PERCENT OF BREAKER TRIP UNIT RATING
40 00 6000 70 00 8000 9000 10,000 6 00 700 8 00 900 1 000 2000 3000 5000 70 80 90 100 2 00 300 400 5 00 60,000 70,000 80,000 90,000 100,000 20,000 30,000 40,000 50,000 50 60
10,000
10,000
2 HOURS
2 HOURS
5,000
5,000
1 HOUR
1 HOUR
Circuit Breaker Time/Current Curves

3,000
For application and coordination purposes only. Based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (60/75C) per terminal. Tested in open air with current in all poles except for instantaneous trip, see below. Maximum Volts Breaker Type 140U-G Ac Volts 60 Hz 480
3,000
2,000
2,000
1,000
1,000
Breaker Rating Continuous Amperes 15-60 70-100 Interrupting Rating (UL Listed) Breaker Type 140U-G Instantaneous Trip, Amperes Single Pole 2 Poles in Series 500-1300 400-1100 1300-1800 700-1300 Symmetrical RMS Amperes 240 Volts 480 Volts 22,000 65,000
500
500
300
300
200
200
100
100
1 MINUTE
1 MINUTE
50
50
30
30
20
20
10
10
Maximum
5
Minimum
TIME IN SECONDS
TIME IN SECONDS
.5
.5
.3
.3
.2
.2
.1
.1
.05
.05
.03
.03
Instantaneous Trip (See Tabulation Above)

.02 .02
Maximum Interrupting Time Interrupting Rating (See Tabulation Above)

.01 .01
.005
.005
.003
.003
.002
.002
.001
60 70 80 90 100 50 60,000 70,000 80,000 90,000 100,000 6000 7000 8 000 9000 10,000 20,000 30,000 40,000 50,000 600 700 800 900 1000 3000 4000 5 000 2000 400 300 500 200
.001
CURRENT IN PERCENT OF BREAKER TRIP UNIT RATING
40752-600 (1) SC-6030-95 Effective October 1997

29
Bulletin 140U/UE

Time-Current Curves, Continued
Bul.140U/UE
Bulletin 140U/UE - H-, J-, L-Frames Current Limiting Characteristics (Ip) 210415V AC, 50/60 Hz
200 kA 100 80
0.2
cos = 0.25
60
CUT-OFF CURRENT ID
40
0.3
20
J
10 8 6
2 5 7 10 20 30 50 kA 100
SHORT CIRCUIT CURRENT ISrms
40752-610 (1) Effective April 2004
30
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-H Thermal-Magnetic Molded Case Circuit Breakers
Thermal/Magnetic Trip Rated Operating Voltage :
600Y / 347V AC 480V AC 415 V AC
Number of Poles: 3, 4 o Ambient 40 C Interrupting Ratings - 50/60 Hz RMS Symmetrical Amperes (kA), Icu Two Series Poles Inst. MagneticTrip Shown. Individual Pole Inst. Magnetic Trip +30%. DC Inst. Magnetic Trip +30% Higher Than AC. Notes: (a) (b) Fixed Inverse-Time Overcurrent Release. Fixed Electromagnetic Release. Total Operation Time. Interrupting Rating determines end of Curve.
(c)
1 minute
(d)
1 minute
40752-601 (1) SC-XXX Effective March 2004
31
Bulletin 140U/UE
Bul.140U/UE
Bulletin 140U/UE - H-, J-, L-Frames Current Limiting Characteristics (Ip) 210415V AC, 50/60 Hz
200 kA 100 80
0.2
cos = 0.25
60
CUT-OFF CURRENT ID
40
0.3
20
J
10 8 6
2 5 7 10 20 30 50 kA 100
SHORT CIRCUIT CURRENT ISrms
40752-610 (1) Effective April 2004
32
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-H IEC-Rated Thermal-Magnetic Molded Case Circuit Breakers
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
7.0
10.0
20.0
50.0
80.0
Circuit Breaker Time/Current Curves 1. 140U/UE-H Circuit Break.Earth Leakage Mod., 3 and 4 Poles, 110 - 480V 60Hz. 2. For application and coordination purposes only. -20 C to 55 C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation.
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
20.0
20.0
.03
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
.1
.3
10
Available I n Settings
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
2.0
2.0
1S
TIME IN SECONDS
1.0 .9 .8 .7 .6 .5 .4 .3 1.0 .9 .8 .7 .6 .5 .4 .3
TIME IN SECONDS
500ms
300ms
.2
150ms
.2
.1 .09 .08 .07 .06 .05 .04 .03
60ms
.1 .09 .08 .07 .06 .05 .04 .03
Inst.
.02 .02
.01 .009 .008 .007 .006 .005 .004 .003
.01 .009 .008 .007 .006 .005 .004 .003
.002
.002
.001
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0 7.0 10.0 20.0 50.0 80.0
.001
40752-602 (1) Curve No. TC01212003E Effective September 2005
Ig (Amperes)
33
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-H UL-Rated Thermal-Magnetic Molded Case Circuit Breakers
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0 7.0 10.0 20.0 50.0 80.0
Circuit Breaker Time/Current Curves 1. 140U/UE-H Cir. Break. Earth Leakage Mod., 3 and 4 Poles, 110 - 480V 60Hz. 2. For application and coordination purposes only. -20 C to 55 C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
20.0
20.0
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
.03
.1
.3
10
Available Ig (A) Settings
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
2.0
2.0
1S
TIME IN SECONDS
TIME IN SECONDS
1.0 .9 .8 .7 .6 .5 .4 .3 1.0 .9 .8 .7 .6 .5 .4 .3
500ms
300ms
150ms
.2 .2
.1 .09 .08 .07 .06 .05 .04 .03
60ms
.1 .09 .08 .07 .06 .05 .04
Inst.
.03
.02
.02
.01 .009 .008 .007 .006 .005 .004 .003
.01 .009 .008 .007 .006 .005 .004 .003
.002
.002
.001
.01
.02
.03
.04 .05
.07
.1
.2
.3
.4
.5
.7
1.0
2.0
3.0
4.0 5.0
7.0
10.0
20.0
50.0
80.0
.001
Ig (A)
34
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-J Thermal-Magnetic Molded Case Circuit Breakers
Allen-Bradley 63250 A
40752-620 (1) SC-XXX Effective March 2004
35
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-J Electronic LS Molded Case Circuit Breakers
Current in Multiples of (Ir)
.5 .7 1 2 3 4 5 7 10 20 30
Long Delay Response & Short Delay with I T Response Curve
2 HOURS
10000 9000 8000 7000 6000 5000
1 HOUR
1.15
4000 3000
Circuit Breaker Time/Current Curve

Long Delay (LD) & Short Delay (SD) with I T Response (LS)
2
2000
Ir Available Sensors (In):

1000 900 800 700 600 500 400 300
In
50 A 20A 20A 25A 30A 32A 40A 45A 50A
100 A 40A 45A 50A 63A 70A 80A 90A 100A
160 63A 80A 90A 100A 110A 125A 150A 160A
250 A 100A 125A 150A 160A 175A 200A 225A 250A
50A 100A 160A 250A Maximum Total Clearing Time
A B C D E F G H
Notes: 1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +88 C cause an over temperature protection trip. For possible continuous ampere derating for ambient above 40C, consult Rockwell Automation. 2. Application frequency is 50/60 Hertz.
200
1 MINUTE
100 90 80 70 60 50 40 30
Available Long Delay Time: 2,4,7,10,12,15,20,24 sec. Shown @ 6x Ir 2,4,7,15,24 seconds +0/-30%
3. There is a memory effect that can act to shorten the Long Delay. The memory effect comes into play if a current above the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset memory. 4. The right portion of the curve is determined by the interrupting rating of the circuit breaker. 5. The left portion of the curve is shown as a multiple of the Long Delay Setting (Long Delay Pick Up = 115% of Ir). Range is 110% - 120%.
20
24
TIME IN SECONDS
. . .
7
6. Total clearing times shown include the response times of the trip unit, the breaker opening, and the interruption of the current. 7. The Short Delay Pick Up has 9 settings/positions: 2 - 8 & 10, 14. 8. Short Delay I T band has a tolerance of 15%. 9. Breakpoint back to FLAT response occurs @ 8x Ir for upper line of the I T curve. 10. For high fault current levels an additional fixed instantaneous hardware override is provided at 14x (In). 11. For LD Response & SD with Flat Response curve, see:
2 2 2
10 9 8 7 6 5 4 3
Minimum Total Clearing Time
15
.
4 3
40752-622
12. For LD Response & SD with I T Response (this curve): 40752-621 13. For Ground Fault Delay Response curve, see: 40752-623
.
2 4
2
1 .9 .8 .7 .6 .5 .4 .3
1 .9 .8 .7 .6 .5
7
.4 .3
8 14
.2
I T Short Delay (See Note 8)

.1 .09 .08 .07 .06 .05 .04 .03
Instantaneous Override (See Note 10)
.2
10
.
67ms
Application Determines End of Curve
.1 .09 .08 .07 .06 .05 .04 .03
See Note 9
.02
14x
.02
.01
.5
.7
10
20
30
40
50
70
100
10
20
30
40
50
70
.01 100
Current in Multiples of (Ir) I T

2
Current in Multiples of ( I n )
Trip Style
40752-621 (1) TC-01201002E Effective September 2003
36
TIME IN SECONDS
Available Short Delay Pick Up Settings 2 - 8,10, 14 x Ir 5% (See Note 7)
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-J Electronic LSI Molded Case Circuit Breakers
.5 .7 1 2 3 4 5 7 10 20 30
Long Delay Response & Short Delay with Flat Response Curve
2 HOURS
10000 9000 8000 7000 6000 5000
1 HOUR
1.15
4000 3000

Long Delay (LD) & Short Delay (SD) with Flat Response (LSI)
2000
Ir Available Sensors (In):

1000 900 800 700 600 500 400 300
In
50A 20A 20A 25A 30A 32A 40A 45A 50A
100A 40A 45A 50A 63A 70A 80A 90A 100A
160A 63A 80A 90A 100A 110A 125A 150A 160A
250A 100A 125A 150A 160A 175A 200A 225A 250A
A B C D E F G H
Notes:
200
1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +88 C cause an overtemperature protection trip. For possible continuous ampere derating for ambient above 40C, consult Rockwell Automation.
100 90 80 70 60 50 40 30
1 MINUTE
2. Application frequency is 50/60 Hertz. 3. There is a memory effect that can act to shorten the Long Delay. The memory effect comes into play if a current above the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset memory. 4. The right portion of the curve is determined by the interrupting rating of the circuit breaker.
20
24
TIME IN SECONDS
. . .
7
5. The left portion of the curve is shown as a multiple of the Long Delay Setting. (Long Delay Pick Up = 115% of Ir). Range is 110% - 120%. 6. Total clearing times shown include the response times of the trip unit, the breaker opening, and the interruption of the current. 7. The Short Delay Pick Up has 9 settings/positions, 2 - 8 & 10, 14. 8. For high fault current levels an additional fixed instantaneous hardware override is provided at 14x (In). 9. For LD Response & SD with Flat Response (this curve): 10. For LD Response & SD with I T Response curve, see: 11. For Ground Fault Delay Response curve, see:
2
10 9 8 7 6 5 4 3
15
40752-622 40752-621 40752-623
.
4
.
2 2 4 14 3 5 6 8
.6
.5 .4 .3
Instantaneous Override (See Note 8) 300ms (P,Q,R)
.5 .4 .3
.2
.2
7
.1 .09 .08 .07 .06 .05 .04 .03
120ms (M,N,O)

.1 .09 .08 .07 .06 .05 .04 .03
10
Inst. (J,K,L)
.02
.02
14x
.01
.5
.7
10
20
30
40
50
70
100
10
20
30
40
50
70
.01 100
Current in Multiples of (In)
40752-622 (1) TC01201001E Effective September 2003
Adjustable Flat Trip Style
TIME IN SECONDS
1 .9 .8 .7 .6
Available Short Delay Pick Up Settings 2 - 8,10, 14 x Ir 5% (See Note 7)
1 .9 .8 .7
37
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-J Electronic LSG & LSIG Molded Case Circuit Breakers
.1
10000 9000 8000 7000 6000 5000 4000
.2
.3
.4
.5
.7
1.0
2.0

Ground Fault Delay Response (LSG, LSIG)
3000
2000
1000 900 800 700 600 500 400 300
Switch Setting J K L M N O P Q R
tSD Inst. Inst. Inst. 120 120 120 300 300 300
tGF Inst. 120 300 Inst. 120 300 Inst. 120 300
200
1 MINUTE
100 90 80 70 60 50 40 30
TIME IN SECONDS
20
Cat. No. 140U-JTI3-D25
10 9 8 7 6 5 4 3
Ground Fault Pickup Settings (Tolerance 10%)
Cat. No. 140U-JTG3-D25
0.4X 0.2X 0.6X 0.3X 1X
1 .9 .8 .7 .6 .5 .4 .3
0.8X
NOTE: Labels shown are for 250A style.
300ms (L,O,R)
.2
Notes:
.1 .09 .08 .07 .06 .05 .04 .03
120ms (K,N,Q)
1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +88 C cause an over-temperature protection trip. For possible continuous ampere derating for ambient above 40C, consult Rockwell Automation. 2.Application frequency is 50/60 Hertz.
Inst. (J,M,P)
3. Trip units are suitable for functional field testing with test kit style # 70C1056G52. 4. For LD Response & SD with Flat Response curve, see: 5. For LD Response & SD with I T Response curve, see: 6. For Ground Fault Delay Response (this curve):
2
40752-622 40752-621 40752-623
.02
.01
.1
.2
.3
.4
.5
.7
1.0
2.0
Ground Current in Multiple of (In)
40752-623 (1) TC01203004E Effective September 2003
38
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-J IEC-Rated Thermal-Magnetic Molded Case Circuit Breakers
1000 900.0 800.0 700.0 600.0 500.0 400.0
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2 3 4 5 7 10
1000 900.0 800.0 700.0 600.0
1. 140U/UE-J Circuit Breaker Earth Leakage Module, 3 and 4 Poles, 110 - 480V 50/60Hz. 2. For application and coordination purposes only. -20C to 55C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation.
500.0 400.0
300.0
300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0
30.0
30.0
20.0
20.0
.03
10.0 9.0 8.0 7.0 6.0 5.0 4.0
.1
.3
10
Available I n settings
10.0 9.0 8.0 7.0 6.0 5.0 4.0
3.0
3.0
2.0
2.0
TIME IN SECONDS
TIME IN SECONDS
1S
1.0 .9 .8 .7 .6 .5 .4
1.0 .9
500ms
.8 .7 .6 .5
300ms
.4
.3
.3
150ms
.2 .2
.1 .09 .08 .07 .06 .05 .04
60ms
.1 .09 .08 .07 .06 .05 .04
.03
.03
Inst
.02 .02
.01 .009 .008 .007 .006 .005 .004
.01 .009 .008 .007 .006 .005 .004
.003
.003
.002
.002
.001
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2 3 4 5 7 10
.001
I n
(Amperes)
39
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-J UL-Rated Thermal-Magnetic Molded Case Circuit Breakers
1000 900.0 800.0 700.0 600.0 500.0 400.0
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2 3 4 5 7 10
1000 900.0 800.0 700.0 600.0
1. 140U/UE-J Circuit Breaker Earth Leakage Module, 3and 4 Poles, 110 - 480V 50/60Hz. 2. For application and coordination purposes only. -20C to 55C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation. F
500.0 400.0
300.0
300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0
30.0
30.0
20.0
20.0
.03
10.0 9.0 8.0 7.0 6.0 5.0 4.0
.1
.3
10
Available Ig(A) Settings.

10.0 9.0 8.0 7.0 6.0 5.0 4.0
3.0
3.0
2.0
2.0
TIME IN SECONDS
TIME IN SECONDS
1S
1.0 .9 .8 .7 .6 .5 .4
1.0 .9
500ms
.8 .7 .6 .5
300ms
.4
.3
.3
150ms
.2 .2
.1 .09 .08 .07 .06 .05 .04
60ms
.1 .09 .08 .07 .06 .05 .04
.03
.03
Inst
.02 .02
.01 .009 .008 .007 .006 .005 .004
.01 .009 .008 .007 .006 .005 .004
.003
.003
.002
.002
.001
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2 3 4 5 7 10
.001
Ig(A)
40
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K3/K6 Thermal-Magnetic Molded Case Circuit Breakers
600 700 800 900 1000 60 70 80 90 100 6000 7000 8000 9000 10,000 4000 2000 3000 300 200 400 500 5000 60,000 70,000 80,000 90,000 100,000
CURRENT IN PERCENT OF BREAKER TRIP UNIT RATING (In)

20,000 30,000 40,000 50 50,000
10,000
10,000
2 HOURS
2 HOURS
5,000
5,000
1 HOUR
1 HOUR

3,000
2,000
For application and coordination purposes only. Based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (60C up to 125 A. 75 C above 125 A) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600V., AC (60 Hz) 250 V., DC
3,000
2,000
1,000
1,000
500
(250-400A)
300
(125-225A)
200
Maximum Single Pole Trip Times at 25 C
Breaker Rating Rated Amperes (In) Instantaneous Trip Amperes 100, 125, 150, 500 to 1000% of trip unit rating 175, 200, 225, (See Figure Below) 250, 300, 350, (Dc values are approximately 40% higher) 400 Interrupting Rating (UL/CSA) RMS Sym Amperes Amperes Breaker Type @ 240 V., AC @ 480 V., AC @ 600 V., AC @ 250 V., DC
140U-K3 140U-K6
500
300
65,000 100,000
35,000 65,000
25,000 35,000
10,000 22,000
200
(100A)
100
Single pole data at 25C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
100
1 MINUTE
1 MINUTE
Minimum
50
Maximum
50
30
30
20
7.5
20
7.5
10
Typical Trip Unit Nameplate
C Thermal Magnetic Trip Unit

10
5
Push to Trip
7.5
10
5 Amps (In)
10
10
Magnetic Multiples Of In
40C
Cat. No.
Individual Pole Adjustments

3 3
Adjustable Magnetic Trip

2 2
TIME IN SECONDS
TIME IN SECONDS
.3
10X
.5
5X
20%
10%
.5
.3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
Maximum Interrupting Time
.01
.01
.005
.005
.003
Interrupting Rating Determines End of Curve
.003
.002
.002
.001
30,000 20,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 60 70 80 90 100 50 6000 7000 8000 9000 10,000 500 600 700 800 900 1000 200 300 400 2000 4000 3000 5000
.001
40752-630 (1) SC-4118-87B Effective October 1997
41
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K0 Thermal-Magnetic Molded Case Circuit Breakers
60 00 7000 8000 9000 10,000 2000 4000 600 700 800 900 1 000 300 200 4 00 500 70 80 90 100 5000 3000 50 60 60,000 70,000 80,000 90,000 100,000

20,000 30,000 40,000 50,000
10,000
10,000
2 HOURS
2 HOURS
5,000
1 HOUR

For application and coordination purposes only. Based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (60C up to 125 A. 75 C above 125 amps) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600V., AC (60 Hz) 250 V., DC
5,000
1 HOUR
3,000
3,000
2,000
2,000
1,000
Breaker Rating Rated Amperes (In) 100, 125, 150, 175, 200, 225, 250, 300, 350, 400
1,000
Instantaneous Trip Amperes 500 to 1000% of trip unit rating (See Figure Below) (DC values are approximately 40% higher)
500
500
(250-400A)
300
200
(125-225A) Maximum Single Pole Trip Times at 25C
Interrupting Rating (UL/CSA) RMS Sym Amperes Breaker Type @ 240 V., AC @ 480 V., AC 140U-K0 200,000
100,000
Amperes
@ 600 V., AC 50,000 @ 250 V., DC 22,000
200 300
Single pole test data at 25C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
(100A)
100 100
1 MINUTE
1 MINUTE
Minimum
50
Maximum
50
30
30
20
7.5 7.5
20
10

10 5 10 5 Amps (In)
Push to Trip
7.5
10
10
40C
Cat. No.

3 3

2 2
TIME IN SECONDS
TIME IN SECONDS
.3
10X
.5
5X
20%
10%
.5
.3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
Maximum Interrupting Time 600 V., Ac

.01 .01
480 V., Ac
.005 .005
240 V., Ac
.003 .003
.002
.002
.001
30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 6000 7000 8000 9000 10,000 20,000 50 60 70 80 90 100 500 600 700 800 900 1000 200 300 400 2000 3000 4000 5000
.001
42
Bulletin 140U/UE
Bul.140U
Time-Current Curves for Bulletin 140U-K Electronic LS, LSG Trip Units and Bulletin 140U-K3, -K6 Molded Case Circuit Breakers
10,000 .5 .7
CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In)

.9 .186 2 3 4 5
6 7 8 9 10
20
2 HOURS
5,000
Circuit Breaker Time/Current Curves (Phase Current)
1 HOUR
Technical Data Covers, Bul. No. 140U-KTH3, -KTG3 Electronic Trip Units for use with Circuit Breaker Types 140U-K3X3 and -K6X3, 400 A Max.
3,000
Fixed Short Delay Time

2,000
Rating Plug Short Delay Pickup xIr 4 Engaged 2 Trip Unit 40 oC 5 6 3 7 8 Cat. In Push to Trip
Standard Fixed Rating Plug

1,000
TEST
Remove
Available Rating Plugs

500
Ampere Rating (In) 400 350 300 250 225 200
Type
Catalog Number 140U-KRP3-D40 140U-KRP3-D35 140U-KRP3-D30 140U-KRP3-D25 140U-KRP3-D22 140U-KRP3-D20
300
200
Long Delay Maximum Total Clearing Time Long Delay Minimum Total Clearing Time
Fixed Fixed Fixed Fixed Fixed Fixed
Short Delay Pickup Range Amperes 800-3200 700-2800 600-2400 500-2000 450-1800 400-1600
100
1 MINUTE
50
Interrupting Ratings 50/60 RMS Sym. Amperes (kA) Breaker Type 140U-K3 140U-K6 Breaker Type
Hz UL/CSA 240V 65 100 IEC 947-2 480V 35 65 600V 25 35
240V 65 100
380V 40 65
415V 40 65
30
140U-K3 140U-K6
20
2X
Notes Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991. There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pick up value exists for a time and then is cleared by the tripping of a down stream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory. Curve accuracy applies from 20 C to +55 C ambient. For possible continuous ampere derating for ambient above 40 C, consult Rockwell Automation. For high fault current levels a fixed instantaneous override is provided at 4000 A. (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. For ground fault time/current curve see 40752-636.
10
3X
Short Delay Pick Up Settings (Tolerance 10%)
4X 5X 6X
TIME IN SECONDS
.5
.2
7X
.3
8X
.1
.1
.05
.05 .04
Fixed Instantaneous Override
.03
.03
.02
.02
SECONDS
.01
.01
.005
.003
.002
.001
.001
1000 2000 3000 4000 5000 10,000 20,000 30,000 40,000 50,000
CURRENT IN AMPS

100,000
.5
.6 .7 .8 .9 1
3 4 5
6 7 8 9 10
20
43
Bulletin 140U/UE
Bul.140U
Time-Current Curves for Bulletin 140U-K Electronic LSI, LSIG Trip Units and Bulletin 140U-K3, -K6 Molded Case Circuit Breakers
.5 .7

.8 . .9 16 2 3 4 5
10,000
6 7 8 9 10
20
2 HOURS
5,000
1 HOUR
Technical Data Covers, Cat. Nos. 140U-KTL3, -KTI3 Electronic Trip Units for use with Circuit Breaker Types 140U-K3, -K6, 400A. max.
3,000
Adjustable Short Delay Time

Rating Plug Short Delay Push to Trip Pickup xIr 5 4 6 3 7 2 Trip Unit o 40 C 8 Time ms 200 100 INST 300 Cat. In Engaged
2,000

1,000
TEST
Remove
500
Available Rating Plugs Ampere Rating (In) 400 350 300 250 225 200
Type
300
200
100
1 MINUTE
Interrupting Ratings 50/60 RMS Sym. Amperes (kA) Breaker Type 140U-K3 140U-K6 Breaker Type
Hz UL/CSA 240V 65 100 IEC 947-2 480V 35 65 600V 25 35
50
240V 65 100
380V 40 65
415V 40 65
30
140U-K3 140U-K6
20
Notes Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991.
2X
10
There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pick up value exists for a time and then is cleared by the tripping of a down stream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory. Curve accuracy applies from 20C to +55C ambient. For possible continuous ampere derating for ambient above 40C, consult Rockwell Automation. For high fault current levels a fixed instantaneous override is provided at 4000A. (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. For ground fault time/current curve see 40752-636.
4X
2
6X 7X 8X
TIME IN SECONDS
.5
.5
3X
5X
300 ms
.3
.4 .3
200 ms
.2 .2
100 ms
.1 .1
.05
I
.05 .04
.03
.03
.02
.02
SECONDS
.01
.01
.005
.003
.002
1000
3000
4000
2000
5000
.001
.001 10,000 20,000 30,000 40,000 50,000
CURRENT IN AMPS
44
100,000
.5
.6 .7 .8 .9 1
3 4 5
6 7 8 9 10
20
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K Electronic LS, LSG Trip Units and 140U-K0 Molded Case Circuit Breakers
.. 8 .9 16 2 3 4 5
10,000
.5
.7
6 7 8 9 10
20
2 HOURS
5,000
1 HOUR
3,000
Technical Data Covers, Cat. No. 140U-KTH3, -KTG3 Electronic Trip Units for use with Circuit Breaker Type 140U-K0, 400A. max. Fixed Short Delay Time Typical Trip Unit Nameplate
Short Delay Push to Trip Pickup xIr 4 Engaged 2 Trip Unit o 40 C 5 6 3 7 8
2,000

1,000
Rating Plug Cat. In
TEST
Remove
500

300
Ampere Rating (In)
Type
200
100
400 350 300 250 225 200
1 MINUTE
50
30
Interrupting Ratings 50/60 RMS Sym. Amperes (kA) Breaker Type 140U-K0
Hz UL/CSA 240V 200 480V 100 600V 50
20
3X
10
Breaker Type 140U-K0
2X
IEC 947-2 240V 200 380V 100 415V 100
4X
Notes Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991. There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pick up value exists for a time and then is cleared by the tripping of a down stream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory. Curve accuracy applies from 20 C to +55 C ambient. For possible continuous amp derating for ambient above 40 C, consult Rockwell Automation For high fault current levels a fixed instantaneous override is provided at 4000A. (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. For ground fault time/current curve see 40752-636.
5X 6X
TIME IN SECONDS
.5
.2
7X
.3
8X
.1
.1
.05
.05 .04
Fixed Instantaneous Override Maximum Interrupting Time
.03
.03
.02
.02
SECONDS
600 VAC
.01
.01
480 VAC 240 VAC
.005
.003
.002
.001
.001
2000 3000 4000 5000

100,000 200,000 10,000 30,000 40,000 20,000 50,000
.5
.6 .7 .8 .9 1
3 4 5
6 7 8 9 10
20
CURRENT IN AMPS
45
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K Electronic LSI, LSIG Trip Units and 140U-K0 Molded Case Circuit Breakers
10,000 .5 .7

.9 1 5
6 7 8 9 10
20
2 HOURS
5,000
1 HOUR
Technical Data Covers, Cat. Nos. 140U-KTL3, -KTI3 Electronic Trip Units for use with Circuit Breaker Cat. No 140U-K0, 400A. max.
3,000

2,000
Rating Plug Short Delay Push to Trip Pickup xIr 4 Engaged 2 Trip Unit o 40 C 5 6 3 7 8 Time ms 200 100 INST 300

1,000
Cat. In
TEST
Remove

500
Ampere Rating (In) 400 350 300 250 225 200
Type
300
200
100
1 MINUTE
Interrupting Ratings 50/60 RMS Sym. Amperes (kA) Breaker Type 140U-K0
Hz UL/CSA 240V 200 IEC 947-2 480V 100 600V 50
50
Breaker Type
30
240V 200
380V 100
415V 100
140U-K0
20
Notes electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991.
2X
10
There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pick up value exists for a time and then is cleared by the tripping of a down stream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory. Curve accuracy applies from 20C to +55 C ambient. For possible continuous ampere derating for ambient above 40C, consult Rockwell Automation. For high fault current levels a fixed instantaneous override is provided at 4000A. (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. For ground fault time/current curve see 40752-636.
4X
2
6X 7X 8X
TIME IN SECONDS
.5
3X
5X
300 ms
.3
200 ms
.2
100 ms
.1 .1
I
.05 .05 .04 .03 .03
Fixed Instantaneous Override Maximum Interrupting Time 600 VAC
.02
.02
SECONDS
.01
.01
480 VAC 240 VAC
.005
.003
.002
.001
2000
3000
4000
5000
10,000
30,000
40,000
20,000
50,000
CURRENT IN AMPS
46
100,000
200,000
.5
.6 .7 .8 .9 1
6 7 8 9 10
.001 20
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K Electronic Trip Units with Ground Fault Protection
480
10,000
2 HOURS
5,000
560 640 720 800
160
240
320
80
400
8000
GROUND CURRENT-AMPERES
1 HOUR
Circuit Breaker Time/Current Curves (Ground Current)

Electronic Trip Units for use with Bulletin 140U-K3, -K6, and K0 Molded Case Circuit Breakers For use with Trip Unit Catalog Numbers 140U-KTG3-D40 140U-KTI3-D40
Rating Plug Cat. In Push to Trip Short Delay Pickup xIr 5 4 6 3 7 2 Trip Unit o 40 C Short Delay Push to Trip Pickup xIr 4 Engaged 2 Trip Unit 40 oC 5 6 3 7 8 Time ms 200 100 INST 300 8 Ground Fault Pickup xIg 4 3 5 2 1 Ig = 80A Ground Fault Pickup xIg
3 2 1 Ig = 80A 4 5
3,000
2,000
Time ms 300 150 INST 500 TEST
1,000
Engaged
Remove
500
Rating Plug Cat. In
Time ms
300 150 INST 500
300
TEST
200
Remove
Notes Curve accuracy applies from 20 C to +55 C ambient. For possible continuous ampere derating for ambient above 40 C, consult Rockwell Automation.
100
1 MINUTE
Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991.
50
For phase time/current curves see 40752-632, -633, -634, or 40752-635.
30
20
10
1xIG
3xIG
4xIG
TIME IN SECONDS
Ground Fault Pickup Settings (Tolerance 10% Except 20% on 1xIG Setting)
2xIG
5xIG
500 ms
.5
300 ms
.3
.2
150 ms
.1
.05
.03
.02
.01
.005
.003
.002
.001
7 8 9 10
100
GROUND CURRENT-IN MULTIPLES OF Ig = 80A
47
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-K0 Thermal-Magnetic Molded Case Circuit Breakers
600 700 800 900 1 000 4 00 60 00 7000 8000 9000 10,000 2000 4000 30 0 200 70 80 90 100 500 5000 3000 50 60 60,000 70,000 80,000 90,000 100,000

20,000 30,000 50,000 40,000
10,000
10,000
2 HOURS
2 HOURS
5,000
1 HOUR

For application and coordination purposes only. Based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (60C up to 125 A. 75 C above 125 amps) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600V., AC (60 Hz) 250 V., DC
5,000
1 HOUR
3,000
3,000
2,000
2,000
1,000
Breaker Rating Rated Amperes (In) 100, 125, 150, 175, 200, 225, 250, 300, 350, 400
1,000
Instantaneous Trip Amperes 500 to 1000% of trip unit rating (See Figure Below) (Dc values are approximately 40% higher)
500
500
(250-400A)
300
200
(125-225A) Maximum Single Pole Trip Times at 25 C
Interrupting Rating (UL/CSA) RMS Sym Amperes Breaker Type @ 240 V., AC @ 480 V., AC 140U-K0 200,000
100,000
Amperes
@ 600 V., AC 50,000 @ 250 V., DC 22,000 0
200 300
Single pole test data at 25 C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
(100A)
100 100
1 MINUTE
1 MINUTE
Minimum
50
Maximum
50
30
30
20
7.5 7.5
20
10

10 5 10 5 Amps (In)
Push to Trip
7.5
10
10
40C
Cat. No.

3 3

2 2
TIME IN SECONDS
TIME IN SECONDS
.3
10X
.5
5X
20%
10%
.5
.3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
Maximum Interrupting Time 600 V., Ac

.01 .01
480 V., Ac
.005 .005
240 V., Ac
.003 .003
.002
.002
.001
30,000 40,000 50,000 60,000 70,000 80,000 90,000 100,000 6000 7000 8000 9000 10,000 20,000 50 60 70 80 90 100 500 600 700 800 900 1000 200 300 400 2000 3000 4000 5000
.001
48
Bulletin 140U/UE

Bul.140U/UE
Time-Current Curves for Bulletin 140U-L Thermal-Magnetic Molded Case Circuit Breakers
For application and coordination purposes only. Thermal calibration based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (75C) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600V., AC (50/60 Hz) 250 V., DC Breaker Rating Rated Amperes (In) 250, 300, 320, 350 Poles 3 and 4
1 Hour
1 Hour
Instantaneous Trip Amperes (see below) 500 to 1000% of trip unit rating (DC values are approximately 40% higher)
Interrupting Rating (UL/CSA) Breaker RMS Sym Amperes Type @ 240 V., AC @ 480 V., AC 140U-L3 140U-L6 65 100 35 65
Amperes @ 600 V., AC 18 35 @ 250 V., DC 22 42
Interrupting Rating (IEC 60947-2) Breaker RMS Sym kA, 50/60 Hz, AC Type @ 240 V. (Ue) @ 480 V (Ue) Icu 140U-L3 140U-L6 65 Ics 65 Icu 35 70 Ics 35 70
kA, DC @600V. (Ue) Icu 12 25 Ics 6 13 @ 250 V.(Ue) Icu 22 42 Ics 22 42
100 100
1 MINUTE
1 MINUTE
Maximum Interruption Time
Interruption Rating determines end of curve
Current in Multiples of Rating (In)
40752-650 (1) TC-XXXXX Effective June 2003
49
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-L Thermal-Magnetic Molded Case Circuit Breakers
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0 7.0 10.0 20.0 50.0 80.0
Circuit Breaker Time/Current Curves 1. 140U/UE-L Cir. Break. Earth Leakage Mod., 3 and 4 Poles, 110 480V 60Hz. 2. For application and coordination purposes only. -20 C 55 C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation.
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
20.0
20.0
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
Available Ig (A) Settings
.03
.1
.5
30
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
2.0
2.0
1S
TIME IN SECONDS
TIME IN SECONDS
1.0 .9 .8 .7 .6 .5 .4 .3 1.0 .9 .8 .7 .6 .5 .4 .3
500ms
300ms
.2
150ms
.2
.1 .09 .08 .07 .06 .05 .04 .03
60ms
.1 .09 .08 .07 .06 .05 .04 .03
.02
Inst.
.02
.01 .009 .008 .007 .006 .005 .004 .003
.01 .009 .008 .007 .006 .005 .004 .003
.002
.002
.001
.01
.02
.03
.04 .05
.07
.1
.2
.3
.4
.5
.7
1.0
2.0
3.0
4.0 5.0
7.0
10.0
20.0
50.0
80.0
.001
Ig (A)
50
Bulletin 140U/UE

Bul.140U/UE
Earth Leakage Curves for Bulletin 140U/UE-L Thermal-Magnetic Molded Case Circuit Breakers
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0 7.0 10.0 20.0 50.0 80.0
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
Circuit Breaker Time/Current Curves 1. 140U/UE-L Cir. Break. Earth Leak. Mod., 3 and 4 Poles, 110 480V 60Hz. 2. For application and coordination purposes only. -20 C 55 C ambient. 3. Total clearing times include the response time of the Earth Leakage module, opening time of the circuit breaker, and interruption of current. 4. For additional curve tolerances, contact Rockwell Automation.
1000.0 900.0 800.0 700.0 600.0 500.0 400.0 300.0
200.0
200.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
100.0 90.0 80.0 70.0 60.0 50.0 40.0 30.0
20.0
20.0
.03
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
.1
.3
10
Available I n Settings
10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0
2.0
2.0
1S
TIME IN SECONDS
1.0 .9 .8 .7 .6 .5 .4 .3 1.0 .9 .8 .7 .6 .5 .4 .3
TIME IN SECONDS
500ms
300ms
.2
150ms
.2
.1 .09 .08 .07 .06 .05 .04 .03
60ms
.1 .09 .08 .07 .06 .05 .04 .03
Inst.
.02 .02
.01 .009 .008 .007 .006 .005 .004 .003
.01 .009 .008 .007 .006 .005 .004 .003
.002
.002
.001
.01 .02 .03 .04 .05 .07 .1 .2 .3 .4 .5 .7 1.0 2.0 3.0 4.0 5.0 7.0 10.0 20.0 50.0 80.0
.001
I n (Amperes)
51
Bulletin 140U/UE
Bul.140U/UE
Long Delay Response & Short Delay with Flat Response Curve, Bulletin 140U/UE-L
.5 .7 1 2 3 4 5 7 10 20 30
2 HOURS
10000 9000 8000 7000 6000 5000

1.15
1 HOUR
Bulletin 140U/UE L-Frame 3- and 4-Pole Molded Case Circuit Breakers

Long Delay (LD) & Short Delay (SD) with Flat Response Available Sensors (In): 250A 400A 600A 630A Ir A B C D E F G H
In
4000 3000
2000
250A 100A 125A 150A 160A 175A 200A 225A 250A
400A 160A 200A 225A 250A 300A 315A 350A 400A
600A 250A 300A 315A 350A 400A 450A 500A 600A
630A 250A 300A 315A 350A 400A 500A 600A 630A
1000 900 800 700 600 500 400 300
Maximum Total Clearing Time Notes:
1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +85 C cause an overtemperature protection trip. For possible continuous ampere derating for ambient above 40C, refer to Rockwell Automation. 2. Application frequency is 50/60 Hertz. 3. There is a memory effect that can act to shorten the Long Delay. The memory effect comes into play if a current above the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset memory. 4. The right portion of the curve is determined by the interrupting rating of the circuit breaker. 5. The left portion of the curve is shown as a multiple of the Long Delay Setting. (Long Delay Pick Up = 115% of Ir). Range is 110% - 120%. 6. Total clearing times shown include the response times of the trip unit, the breaker opening, and the interruption of the current. 7. The Short Delay Pick Up has 8 settings/positions, 2 - 8 & 10. 8. For high fault current levels an additional fixed instantaneous hardware override is provided (corresponding to SDPU position 9) at 14x (In) and designated as 14I i. Instantaneous tolerance is 20%. 9. For LD Response & SD with Flat Response (this curve): 10. For LD Response & SD with I T Response curve, see: 11. For Ground Fault Delay Response curve, see:
2
200
1 MINUTE
100 90 80 70 60 50 40 30
20
24
TIME IN SECONDS
. . .
7
10 9 8 7 6 5 4 3
15
TC01207004E TC01207005E TC01207006E
.
4
.
2
8 5
.6 .5 .4
.5 .4 .3
300ms (P,Q,R) Instantaneous Override (See Note 8)

7
.3
.2
.2
.1 .09 .08 .07 .06 .05 .04 .03
120ms (M,N,O)

.1 .09 .08 .07 .06 .05 .04 .03
10
Inst. (J,K,L)
.02
.02
14 Ii
.01
.5
.7
10
20
30
40
50
70
100
10
20
30
40
50
70
.01 100
Adjustable Flat Trip Style
40752-653 (1) TC01207004E Effective March 2006
52
TIME IN SECONDS
1 .9 .8 .7 .6
Available Short Delay Pick Up Settings 2 - 8,10 x Ir 5% (See Note 7)
1 .9 .8 .7
Bulletin 140U/UE
Bul.140U/UE
Long-Delay Response & Short-Delay with I2T Response Curve, Bulletin 140U/UE-L
.5 .7 1 2 3 4 5 7 10 20 30
Long Delay Response & Short Delay with I T Response Curve
2 HOURS
10000 9000 8000 7000 6000 5000

1.15
1 HOUR
Bulletin 140U/UE L-Frame 3- and 4-Pole Molded Case Circuit Breakers

2
4000 3000
Long Delay (LD) & Short Delay (SD) with I T Response

2000
Available Sensors (In):

1000 900 800 700 600 500 400 300
Ir A B C D E F G H
In
250A 100A 125A 150A 160A 175A 200A 225A 250A
400A 160A 200A 225A 250A 300A 315A 350A 400A
600A 250A 300A 315A 350A 400A 450A 500A 600A
630A 250A 300A 315A 350A 400A 500A 600A 630A
Notes: 1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +85 C cause an over temperature protection trip. For possible continuous ampere derating for ambient above 40C, refer to Rockwell Automation. 2. Application frequency is 50/60 Hertz.
200
1 MINUTE
100 90 80 70 60 50 40 30
3. There is a memory effect that can act to shorten the Long Delay. The memory effect comes into play if a current above the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset memory. 4. The right portion of the curve is determined by the interrupting rating of the circuit breaker. 5. The left portion of the curve is shown as a multiple of the Long Delay Setting (Long Delay Pick Up = 115% of Ir). Range is 110% - 120%.
20
24
TIME IN SECONDS
. . .
7
6. Total clearing times shown include the response times of the trip unit, the breaker opening, and the interruption of the current. 7. The Short Delay Pick Up has eight settings/positions: 2 - 8 & 10. 8. Short Delay I T band has a tolerance of 15%. 9. Breakpoint back to FLAT response occurs @ 8x Ir for upper line of the I T curve. 10. For high fault current levels an additional fixed instantaneous hardware override is provided (corresponding to SDPU position 9) at 14x (In) and designated as 14I i . Instantaneous tolerance is 20% 11. For LD Response & SD with Flat Response curve, see:
2 2 2
10 9 8 7 6 5 4 3
15
.
4 3
40752-653
12. For LD Response & SD with I T Response (this curve): 40752-654
.
2 4
13. For Ground Fault Delay Response curve, see:
40752-655
2
1 .9 .8 .7 .6 .5 .4 .3
1 .9 .8 .7 .6 .5
7
.4 .3
8
.2
.2
I T Short Delay (See Note 8)

.1 .09 .08 .07 .06 .05 .04 .03
10
.
67ms
.1 .09 .08 .07 .06 .05 .04 .03
See Note 9
.02
14 Ii
.02
.01
.5
.7
10
20
30
40
50
70
100
10
20
30
40
50
70
.01 100
Current in Multiples of (Ir) I T

2
Trip Style
TIME IN SECONDS
Available Short Delay Pick Up Settings 2 - 8 & 10 x Ir 5% (See Notes 7 and 10)
Instantaneous Override (See Note 10)
53
Bulletin 140U/UE
Bul.140U/UE
Ground Fault Delay Response Curve, Bulletin 140U/UE-L
.1
10000 9000 8000 7000 6000 5000 4000 3000
.2
.3
.4
.5
.7
1.0
2.0

bulletin 140U/UE L-Frame 3- and 4-Pole Molded Case Circuit Breakers
Ground Fault Delay Response Notes: 1. Curve accuracy applies from -20C to +55C ambient. Temperatures above +85 C cause an over-temperature protection trip. For possible continuous ampere derating for ambient above 40C, refer to Rockwell Automation. 2.Application frequency is 50/60 Hertz.
2000
1000 900 800 700 600 500 400 300
3. Trip units are suitable for functional field testing with test kit style # 70C1056G52. 4. For LD Response & SD with Flat Response curve, see: 5. For LD Response & SD with I T Response curve, see: 6. For Ground Fault Delay Response (this curve):
2
40752-653 40752-654 40752-655
200
1 MINUTE
100 90 80 70 60 50 40 30
TIME IN SECONDS
20
10 9 8 7 6 5 4 3
Ground Fault Pickup Settings (Tolerance 10%) NOTE: Refer to table below for variations.
Available Sensors (In): 250A 400A 600A 630A

.4X .2X .6X .3X 1X
Ir A B C D E F G H
In
250A 100A 125A 150A 160A 175A 200A 225A 250A
400A 160A 200A 225A 250A 300A 315A 350A 400A
600A 250A 300A 315A 350A 400A 450A 500A 600A
630A 250A 300A 315A 350A 400A 500A 600A 630A
1 .9 .8 .7 .6 .5 .4 .3
.8X
300ms (L,O,R)
.2
.1 .09 .08 .07 .06 .05 .04 .03
120ms (K,N,Q)
Inst. (J,M,P)
.02
.01
.1
.2
.3
.4
.5
.7
1.0
2.0
Ground Current in Multiple of (In)
54
Bulletin 140U/UE

Bul.140U
Time-Current Curves for Bulletin 140U-Q3/Q6 Thermal-Magnetic Molded Case Circuit Breakers

600 70 0 80 0 900 1000 6000 7000 8000 9000 10,000 2000 3000 4000 5000 300 400 50 0 70 80 90 100 200 60,000 70,000 80,000 90,000 100,000 20,000 30,000 40,000 50,000
50
60
10,000
10,000
2 HOURS
2 HOURS
5,000
5,000
1 HOUR
1 HOUR

3,000
2,000
For application and coordination purposes only. Thermal calibration based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (75C) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600 V., AC (50/60 Hz.) 250 V., DC
3,000
2,000
1,000
Breaker Rating Rated Amperes (In) 300, 350, 400, 500, 600
1,000
Instantaneous Trip Amperes (See Figure Below) 500 to 1000% of trip unit rating (DC values are approximately 40% higher)
500
500
300
Maximum Single Pole Trip Times at 25 1 C
Interrupting Rating Breaker UL/CSA Type RMS Sym. kA, 50/60 Hz. 240 V. 140U-Q3 140U-Q6 480 V. 600 V. 25 35
kA, Dc 250 V. 10 20 kA, Dc 415 V., (U ) e Icu Ics 40 65 10 17 250 V., (U) e Icu Ics 10 20 3 5
300
200
Minimum
100
Maximum
65 35 100 65 IEC 947-2 RMS Sym. kA, 50/60 Hz. 240 V., (U ) e Icu Ics 380 V., (U) e Icu Ics 40 65 10 17
200
100
1 MINUTE
1 MINUTE
50
140U-Q3 65 140U-Q6 100
17 25
Utilization Category A U IMP = 8 kV Note: For additional information on the trip unit, see IL 29C606. Single pole data at 25 C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
50
30
30
20
20
7.5
7.5
10

10 5 10 5 Amps (In)
Push to Trip
7.5
10
10 5
40C
Cat. No.
TIME IN SECONDS
TIME IN SECONDS
10X
5X
20%
10%
1
.5
.5

.3 .3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
.01
.01
.005
.005
.003
.003
.002
.002
.001
60,000 70,000 80,000 90,000 100,000 30,000 6000 7000 8000 9000 10,000 20,000 50,000 40,000 60 70 80 90 100 50 500 600 700 800 9 00 1000 30 0 40 0 200 2000 3000 4000 5000
.001
55
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-M5, -M6 Thermal-Magnetic (300600 A) Molded Case Circuit Breakers
6000 7000 8000 9000 10,000 600 700 800 900 1000 3000 4000 2000 60 70 80 90 100 200 5000 500 300 400 60,000 70,000 80,000 90,000 100,000 20,000 30,000 40,000 50,000
50
10,000
10,000
2 HOURS
5,000
1 HOUR

For application and coordination purposes only. Thermal calibration based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (75 C) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600 V AC (50/60 Hz.) 250 V DC
5,000
3,000
3,000
2,000
2,000
1,000
Breaker Rating Rated Amperes (I n 300, 350, 400, 500, 600
1,000
Instantaneous Trip Amperes (See Figure Below) 500 to 1000% of trip unit rating (DC values are approximately 40% higher)
500
500
300
Maximum Single Pole Trip Times at 25 1 ?C
Interrupting Rating Breaker UL/CSA Type RMS Sym. kA, 50/60 Hz. 140U-M5 140U-M6 Breaker Type 240V 65 100 IEC 947-2 RMS Sym. kA, 50/60 Hz. ) 240V (Ue Icu Ics 140U-M5 140U-M6 65 100 65 100 380/415V (Ue ) 690V (Ue) Icu Ics Ics Icu 50 70 50 50 20 25 10 13 480V 50 65 600V 25 35
kA, DC 250V 22 25 kA, DC 250V (Ue) Ics Icu 20 20 10 10
300
200
200
Minimum
100
Maximum
100
1 MINUTE
50
Utilization Category A U IMP = 8 kV Note: For additional information on the trip unit, see IL 29C607.
50
30
Single pole data at 25 C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
30
20
7.5 7.5 Push to Trip 7.5
20
10
10
10
5 Amps (In)
10
10
40 C
Cat. No.

3 3
TIME IN SECONDS
10X
5X
? 20%
? 10%
1
.5
.5

.3 .3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
.01
.01
.005
.005
.003
.003
.002
.002
.001 30,000 40,000 60,000 70,000 80,000 90,000 100,000 20,000 6000 7000 8000 9000 10,000 50,000 60 70 80 90 100 50 500 600 700 800 900 1000 200 300 400 2000 3000 4000 5000
.001
40752-674 (1) SC-6911-98 Effective February 1999

56
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-M5, -M6 Thermal-Magnetic (700 & 800 A) Molded Case Circuit Breakers
2000 3000 6000 7000 8 0 00 9000 10,000 600 700 800 900 1000 4000 5000 200 300 400 70 80 90 100 500 60,000 70,000 80,000 90,000 100,000 30,000 40,000 20,000 50,000 50 60
10,000
10,000
2 HOURS
2 HOURS
5,000
5,000
1 HOUR
1 HOUR

3,000
2,000
For application and coordination purposes only. Thermal calibration based on 40 C ambient, cold start. Connected with four (4) feet of rated wire (75 C) per terminal. Tested in open air with current in all poles. Instantaneous calibration based on single-pole tests. Maximum Voltage 600 V AC (50/60 Hz.) 250 V DC
3,000
2,000
1,000
Breaker Rating Rated Amperes (I 700, 800
1,000
n)
Instantaneous Trip Amperes (See Figure Below) 400 to 800% of Trip Unit rating (DC values are approximately 40% higher)
500
500
300
Maximum Single Pole Trip Times at 25 1 ?C
Interrupting Rating Breaker UL/CSA Type RMS Sym. kA, 50/60 Hz. 140U-M5 140U-M6 Breaker Type 240V 65 100 IEC 947-2 RMS Sym. kA, 50/60 Hz. 240V (U ) e Ics Icu 140U-M5 140U-M6 65 100 65 100 380/415V (U e) Ics Icu 50 70 50 50 690V (U) e Ics Icu 20 25 10 13 480V 50 65 600V 25 35
kA, DC 250V 22 25 kA, DC 250V (U) e Ics Icu 20 20 10 10
300
200
200
Minimum
100
Maximum
100
1 MINUTE
1 MINUTE
50
Utilization Category A U IMP = 8 kV
50
30
Single pole data at 25C based on NEMA Procedures (AB 4-1991) for verifying performance of molded case circuit breakers.
6 6 Thermal Magnetic Trip Unit 8 4 8 4 Amps (In) C Cat. No. Push to Trip 8 4 6
30
20
20
10
10

3 3
TIME IN SECONDS
TIME IN SECONDS
4X
8X
? 20%
? 10%
1
.5
.5

.3 .3
.2
.2
.1
.1
.05
.05
.03
.03
.02
.02
.01
.01
.005
.005
.003
.003
.002
.002
.001 20,000 30,000 60,000 70,000 80,000 90,000 100,000 40,000 6000 7000 8000 9000 10,000 50,000 50 60 70 80 90 100 500 600 70 0 800 900 1000 200 300 400 4000 2000 3000 5000
.001

57
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-M Electronic LS, LSG Trip Units and 140U-M5, -M6 Molded Case Circuit Breakers
10,000 .5
CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In) .7 .9 16 .8 . 2 3 4 5 6 7 8 9 10
20
2 HO U R S

5,000
Technical Data Covers, Cat. Nos. 140U-MTL3, -MTG3 Electronic Trip Unit for use with Circuit Breaker Types 140U-M5, -M6, 800 A max.
1 HO U R
3,000
2,000
Fixed Short Delay Time

Test

1,000
Rating Plug Cat. In Engaged Push to Trip
Short Delay Pickup x I n 5 4 6 3 7 2 8
Trip Unit 40o C Ambient
Remove
500
Available Rating Plugs Ampere Rating (I n ) 800 700 600 500 450 400 Interrupting Rating
Type
300
200
Rating Plug Catalog Number 140U-MRP3-D80 140U-MRP3-D70 140U-MRP3-D60 140U-MRP3-D50 140U-MRP3-D45 140U-MRP3-D40
100
Breaker Type 140U-M5 140U-M6 Breaker Type
UL/CSA RMS Sym. kA, 50/60 Hz 240V 65 100 480V 50 65 600V 25 35
1 MIN U T E
50
30
140U-M5 140U-M6
IEC 947-2 RMS Sym. kA, 50/60 Hz 380/415V (U 240V (U e) Ics Icu Ics Icu 65 100 Utilization Category A U imp = 8kV 65 100 50 70 50 50
e)
Icu 20 25
690V (U e) Ics 10 13
20
10
2X
3X
Notes Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA AB4-1991 publications.
3 2
Calibration response in short delay pick-up range is same for 1, 2 or 3 poles in series. There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pick-up value exists for a time and then is cleared by the tripping of a downstream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory.
4X 5X
TIME IN SECONDS
Curve accuracy applies from 20 C to +55C ambient. For possible continuous ampere derating for ambient above 40 C, consult Rockwell Automation.
8X
For high fault current levels a fixed instantaneous override is provided at 5500A.
1
(Tolerance 15%).
6X
The end of the curve is determined by the interrupting rating of the circuit breaker.
See above tabulation.
.5
For ground fault time/current curves see 40752-678.
.2
7X
.3
.1
.1
.05
.05 .04
.03
.03
.02
.02
.01
SECONDS
.01
.005
.003
.002
30,000
40,000
10,000
20,000
50,000
CURRENT IN AMPS

58
100,000
.001 2 3 4 5 6 7 8 9 10 .5 .6 .7 .8 .9 1 CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In)
1000
2000
4000
3000
5000
20
.001
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-M Electronic LSI, LSIG Trip Units and 140U-M5, -M6 Molded Case Circuit Breakers
10,000 2 HO U R S .5
.7
CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In) .9 16 .8 . 2 3 4 5 6 7 8 9 10
20

5,000
1 HO U R
Technical Data Covers, Cat. nos. 140U-MTH3, -MTI3 Electronic Trip Units for use with Circuit Breaker Types 140U-M5, -M6, 800 A max.
3,000

2,000

Time MIsec 200 100 I 300 Trip Unit o 40 C Ambient Test

1,000
Rating Plug Cat. In Engaged Push to Trip
Short Delay Pickup x In 5 4 6 3 7 2 8
Remove
Available Rating Plugs Ampere Rating (In)

500
Type
300
800 700 600 500 450 400
Rating Plug Catalog Number 140U-MRP3-D80 140U-MRP3-D70 140U-MRP3-D60 140U-MRP3-D50 140U-MRP3-D45 140U-MRP3-D40
200
Interrupting Rating Breaker Type 140U-M5 140U-M6 Breaker Type UL/CSA RMS Sym. kA, 50/60 Hz 240V 65 100 IEC 947-2 RMS Sym. kA, 50/60 Hz 240V (Ue) Icu Ics 140U-M5 140U-M6 65 100 Utilization Category A U imp = 8kV 65 100 380/415V (U e ) Icu Ics 50 70 50 50 690V (U e) Icu Ics 20 25 10 13 480V 50 65 600V 25 35
100
1 MIN U T E
50
30
20
2X
10
Notes Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA AB4-1991 publications. Calibration response in short delay pickup range is same for 1, 2 or 3 poles in series.
4X
Short Delay Pickup Settings (Tolerance ? 10%)
6X
There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pickup value exists for a time and then is cleared by the tripping of a downstream device or the circuit breaker itself. A subsequent overload will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory. Curve accuracy applies from 20 C to +55 C ambient. For possible continuous ampere derating for ambient above 40 C, consult Rockwell Automation. For high fault current levels a fixed instantaneous override is provided at 5500A. (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. For ground fault time/current curves see 40752-678.
TIME IN SECONDS
.5
3X
5X
7X
8X
300 ms
.3
200 ms
.2
100 ms
.1 .1
I
.05 .05 .04 .03 .03
.02
.02
.01
SECONDS
.01
.005
.003
.002
1000
4000
2000
3000
5000
.001
.001 10,000 40,000 30,000 50,000 20,000 100,000 .5 2 3 4 5 6 7 8 9 10 .6 .7 .8 .9 1 CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In) 20
CURRENT IN AMPS

59
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-M Electronic Trip Units with Ground Fault Protection
Ground Fault Protection
320 160 10,000 1120 1280 1440 1600 800 480 640 960 16000
GROUND CURRENT-AMPERES
2 HOURS
5,000
1 HOUR

Technical Data Covers, Electronic Trip Units for use with Circuit Breaker Types 140U-M5, -M6, 800 A max. Fixed Short Delay Time
Rating Plug
3,000

Short Delay Pickup x In Ground Fault Pickup x Ig 3 2 1 4 5 Time MIsec 500 Trip Unit 40 o C Ambient Test 5
2,000
Cat. In Engaged Push to Trip
4 2
6 3 7 8
300 150 I Ig = 160A
Remove
1,000

Rating Plug Cat. In Push to Trip 4 Engaged 2 Short Delay Pickup x In 5 6 3 7 8 Time MIsec 200 100 I 300 Ground Fault Pickup x Ig 3 2 1 4 5 Time MIsec 500

Test
500
300 150 I Ig = 160A
Trip Unit 40 oC Ambient
Remove
300
Notes Curve accuracy applies from 20 C to +55 C ambient. For possible continuous ampere derating for ambient above 40 C, consult Rockwell Automation. Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication (AB4-1991). For phase time/current curves see: 40752-674 40752-675 40752-676 40752-677
200
100
1 MINUTE
50
30
20
10
1xIG
3xIG
5 3
4xIG
TIME IN SECONDS
Ground Fault Pickup Settings (Tolerance 10% Except 20% on 1xIG Setting)
2xIG
5xIG
500 ms
.5
300 ms
.3
.2
150 ms
.1
.05
.03
.02
.01
.005
.003
.002
.001
7 8 910
100
GROUND CURRENT-IN MULTIPLES OF Ig = 160A
60
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-N Electronic LS Trip Units
10,000
CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In) .5 .6 .7 .8 .9 1 2 3 4 5 6 7 8 9 10
20
2 HO U R S
Circuit Breaker
5,000
Time/Current Curves (Phase Current)
1 HO U R
Electronic Trip Units are AC only devices that employ microprocessor based technology that provides true RMS current sensing means for proper correlation with thermal characteristics of conductors and equipment. They are used with Circuit Breaker Types 140U-N5, -N6, and -N0. I2t Ramp Short Time Delay
Rating Plug
3,000
2,000

1,000
Push to Trip
Cat. /n Y
TEST
Trip Unit 40 C Ambient
Engaged
Remov e
500
Frame Rating Amperes (Max.) 1200
A vailable Rating Plugs Ampere Rating (I n) 1200 1000 800 700 600 600, 800, 1000, 1200
Type
Catalog Number 140U-NRP3-E12 140U-NRP3-E10 140U-NRP3-D80 140U-NRP3-D70 140U-NRP3-D60 140U-NRPA-E12
300
200
Fixed Fixed Fixed Fixed Fixed Adj.
100
50
Interrupting Ratings 50/60 Hz RMS Sym. Amperes (kA) UL/CSA Breaker Type 240V 480V 65 50 ND, CND 100 65 HND, CHND 200 100 NDC, CNDC
1 MIN U T E
600V 25 35 50
IEC 947-2 220-240V 65 100 200
380-415V 50 65 100
30
20
ICS = .25 ICU ICW = 15 kA @ .5S U imp = 8kV
3X
2X
Notes
Curve accuracy applies from -20 C to +55 ambient above 40 C, consult Rockwell Automation Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991. For ground fault time-current curves see 40752-692.
10
3 2
There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pickup value exists for a time and then is cleared by the tripping of a downstream device or the circuit breaker itself. A subsequent overloads will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory For high fault current levels a fixed instantaneous override is provided at14000A (Tolerance 15%).
4X 5X
8X
TIME IN SECONDS
The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. Not UL/CSA Listed.
.5
.2
7X
.3
6X
.1
.1
.05
.05
Fixed Instantaneous Overide
.03
.03 .02
.02
SECONDS
.01
.01
.005
.005
.003
.003 .002
.002
60,000 70,000 80,000 90,000 100,000
CURRENT IN AMPS
40752-690 (1) SC-5375-92A Effective October 1997

200,000
40,000
10,000
20,000
30,000
50,000
20
.001
61
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-N LSI Electronic Trip Unit
CURRENT IN MULTIPLES OF RATING PLUG AMPERES (In) .5 .6 .7 .8 .9 1 2 3 4 5 6 7 8 9 10
10,000
20
2 HO U R S
Circuit Breaker
Time/Current Curves (Phase Current)
1 HO U R
5,000
Electronic Trip Units are AC only devices that employ microprocessor-based technology that provides true RMS current sensing means for proper correlation with thermal characteristics of conductors and equipment. For use with Circuit Breaker Types 140U-N5, -N6, and -N0. Adjustable Short Time Delay
Rating Plug
Push to Trip Cat. /n Y Short Delay Pickup x In 5 4 6 3 2 7 8
3,000
2,000
TEST
Trip Unit 40 Ambient C
Engaged
Remov e
1,000
Frame Rating Amperes (Max.) 1200 A vailable Rating Plugs Ampere Type Rating (I n) 1200 1000 800 700 600 600, 800, 1000, 1200 Fixed Fixed Fixed Fixed Fixed Adj. Catalog Number 140U-NRP3-E12 140U-NRP3-E10 140U-NRP3-D80 140U-NRP3-D70 140U-NRP3-D60 140U-NRPA-E12 Short Delay Pickup Range Amperes 2400-9600 2000-8000 1600-6400 1400-5600 1200-4800 1200-9600
500
300
200
100
1 MIN U T E
Interrupting Ratings 50/60 Hz RMS Sym. Amperes (kA) UL/CSA Breaker Type 240V 480V 65 50 140U-N5 100 65 140U-N6 200 100 140U-N0
600V 25 35 50
IEC 947-2 220-240V 65 100 200
380-415V 50 65 100
50
Notes
ICS = .25 ICU ICW = 15 kA @ .5S U imp = 8kV

Curve accuracy applies from -20 C to +55 C ambient. For possible ampere derating for ambient above 40 C, consult Rockwell Automation Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991.
30
20
2X
For ground fault time-current curves see 40752-692. There is a memory effect that can act to shorten the long delay. The memory effect comes into play if a current above the long delay pickup value exists for a time and then is cleared by the tripping of a downstream device or the circuit breaker itself. A subsequent overloads will cause the circuit breaker to trip in shorter time than normal. The amount of time delay reduction is inverse to the amount of time that has elapsed since the previous overload. Approximately five minutes is required between overloads to completely reset the memory
10
4X
3 2
For high fault current levels a fixed instantaneous override is provided at14000A (Tolerance 15%). The end of the curve is determined by the interrupting rating of the circuit breaker. See above tabulation. Not UL/CSA Listed.
6X 3X 5X 7X 8X
TIME IN SECONDS
.5
300 MS
.3
200 MS
.2
100MS
.1 .1
I
.05 .05
Fixed Instantaneous Overide
.03
.03 .02
.02
.01
SECONDS
.01
.005
.005
.003
.003 .002
.002
CURRENT IN AMPS

62
60,000 70,000 80,000 90,000 100,000
200,000
40,000
50,000
20,000
10,000
30,000
20
.001
Bulletin 140U/UE
Bul.140U/UE
Time-Current Curves for Bulletin 140U-N Electronic LSG, LSIG Trip Units with Ground Fault Protection
CURRENT IN AMPERES
2000 3000 600 700 800 900 1000 4000 .50 .60 .70 .80 .90 100 5000
200
300
400
10,000
2 HO U R S
500
Circuit Breaker
Time/Current Curves (Ground Current)
1 HO U R
5,000
Electronic Trip Units are AC only devices that employ microprocessor-based technology that provides true RMS current sensing means for proper correlation with thermal characteristics of conductors and equipment. They are used with Circuit Breaker Types 140U-N5, -N6, and N0.
3,000 Typical Trip Unit Nameplate
2,000
Rating Plug
Push to Trip Cat. /n Y
Ground Fault Pickup x IG 4 3 5 2 1 6
Time 500 300 150 1 TEST
1,000
Engaged Remov e
Trip Unit 40 Ambient C

Millisec
IG=200A
500 Notes 300 200

Curve accuracy applies from 20 C to + 55C ambient. Electronic trip units are suitable for functional field testing with test kit. For field testing using primary injection methods, follow NEMA publication AB-4-1991. For phase time-current curves see 40752-690, and -691.
100
1 MIN U T E
50
30
20
200 A .
600 A .
10
1000 A .
3 2
Ground Fault Pick Up Settings (Tolerance 10% Except 20% on 200 A. Setting)
400 A . 1200 A .
1
TIME IN SECONDS
800 A .
.5
.5 SEC
.3
.3 SEC
.2
.15 SEC
.1
.05
.03
.02
.01
.005
.003
.002
.50 .60 .70 .80 .90 100
.001
500
600 700 800 900 1000
2000
4000
CURRENT IN AMPERES
3000
5000
200
300
400
63
Publication 140U-TD001B-EN-P November 2006 Copyright 2006 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.

Bulletin 140U/Ue: Molded Case Circuit Breakers

Uploaded by

Copyright:

Available Formats

Bulletin 140U/Ue: Molded Case Circuit Breakers

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bulletin 140U/Ue: Molded Case Circuit Breakers

Uploaded by

Copyright:

Available Formats

TECHNICAL DATA

Molded Case Circuit Breakers

Auxiliary Circuit Specifications

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Rated Insulation Voltage (U) According to IEC 60947-2

Rated Impulse Withstand Voltage (Uimp) [kV] [kV] 2-3P 6 4 6 4 6 4 8 4 8 4 8 4 8 4 8 4 8 4

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Auxiliary Circuit Specifications

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Dimensions in Inches (mm)

140U-K-MHS 140U-L-MHS 140U-L-MHS

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

End Cap Optional 140UH-ECM Molded Housing

Slip on Terminal box lug Fastene r Torque

Cable Type Cable Temperature Rating Cable Quantity

Wire Strip Length Wire Range

in. mm AWG mm2

Lb-in #1410 36 lb-in. Wire Torque Nm 2.56 mm 3.9 Nm

Std/Optional Cat. No. Material Terminal Fastener Hardware Lb-in Nm

#10-32 Slotted Screw

#10-32 Slotted Screw

Flathea Terminal d Fastene 3550 r Torque 4.05. 6

10 0.2 Cu Only 60/75C (1) 1/2

45 lb-in 5 Nm Cu/Al 60/75C (3)

45 lb-in 5 Nm Cu/Al 60/75C (6)

12.7 #141 0 #8 10 #64 1625

Allen - 4 mm 3438 Lb-in 3.84.3 Nm

Terminal Type Lb-in Nm 35 4.0

Slotted 40 4.5 45 5.1

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

mm2 25185 Lb-in Nm

Terminal Type Wire Torque

Std/Optional Cat. No. Material

#3350 3/0250 3/0250

Terminal Type Wire Torque Lb-in Nm

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Terminal Type Wire Torque

Visit our website: www.ab.com/catalogs

Molded Case Circuit Breakers

Cable Type Cable Temperature Rating

Cable Quantity Wire Strip Length in. mm AWG mm2 Lb-in Nm

Material A Dim. B C D Fastener Torque M

AWG mm2 Lb-in Nm

Terminal Type Wire Torque

Visit our website: www.ab.com/catalogs