Sony Hcd Ec59

HCD-EC59
SERVICE MANUAL E Model

Ver. 1.0 2010.06
• HCD-EC59 is the amplifier, USB, CD player and

tuner section in MHC-EC59.
• MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson.
• Windows Media is either a registered trademark or trademark of Microsoft Corporation in the Model Name Using Similar Mechanism HCD-EX6/EX6T
United States and/or other countries.
• This product is protected by certain intellectual property rights of Microsoft Corporation. Use or
Base Unit Name BU-D1BD74UR
distribution of such technology outside of this product is prohibited without a license from Micro- Optical Pick-up Block Name DA11MMVGP
soft or an authorized Microsoft subsidiary.
SPECIFICATIONS
Main unit CD player section General
System: Power requirements
Compact disc and digital audio Mexican model:
Amplifier section system AC 127 V, 60 Hz
The following measured at AC 127 V, 60 Hz Laser Diode Properties Argentine model:
(Mexican model) Emission Duration: Continuous AC 220 V, 50/60 Hz
The following measured at AC 220 V, Laser Output*: Less than 44.6μW Other models:
50/60 Hz (Argentine model) * This output is the value AC 120 V, 220 V or 230 V 240 V,
The following measured at AC 120 V, 220 V, measurement at a distance of 50/60 Hz, adjustable with voltage
240 V, 50/60 Hz (Other models) 200mm from the objective lens selector
surface on the Optical Pick-up Block Power consumption: 85 W
Power output (rated): with 7mm aperture. (0.5 Wat the Power Saving Mode)
25 W + 25 W (at 6 Ω, 1 kHz, 1% Frequency response: 20 Hz – 20 kHz Dimensions (W/H/D) (excl. speakers)
THD) Signal-to-noise ratio: More than 90 dB Approx. 200 mm × 306 mm ×
RMS output power (reference): Dynamic range: More than 88 dB 305 mm
60 W + 60 W (per channel at 6 Ω, Mass (excl. speakers): Approx. 3.8 kg
1 kHz)
Tuner section
FM stereo, FM/AM superheterodyne tuner Design and specifications are subject to
Inputs Antenna: change without notice.
PC IN (stereo mini jack): FM lead antenna
Sensitivity 800 mV, impedance AM loop antenna
22 kilohms
Standby power consumption: 0.5 W
FM tuner section:
Outputs Tuning range: Halogenated flame retardants are not used
in the certain printed wiring boards.
PHONES (stereo mini jack): 87.5 MHz – 108.0 MHz (50 kHz step)
accepts headphones with an Intermediate frequency: 225 kHz
impedance of 8 Ω or more
SPEAKERS: impedance: 6 Ω AM tuner section:
Tuning range
Latin American models:
USB section 530 kHz – 1,710 kHz (10 kHz step)
Supported bit rate: 531 kHz – 1,710 kHz (9 kHz step)
MP3 (MPEG 1 Audio Layer-3): Other models:
32 kbps – 320 kbps, VBR 531 kHz – 1,602 kHz (9 kHz step)
WMA: 48 kbps – 192 kbps 530 kHz – 1,610 kHz (10 kHz step)
AAC: 48 kbps – 320 kbps Intermediate frequency: 53 kHz
Sampling frequencies:
MP3 (MPEG 1 Audio Layer-3):
32/44.1/48 kHz
COMPACT DISC RECEIVER

WMA: 44.1 kHz
AAC: 44.1 kHz
(USB) port:
Maximum current:
500 mA
9-889-885-01 Sony Corporation

2010F05-1 Audio&Video Business Group
© 2010.06 Published by Sony Techno Create Corporation
HCD-EC59
NOTES ON CHIP COMPONENT REPLACEMENT TABLE OF CONTENTS

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam- 1. SERVICING NOTES ............................................. 3
aged by heat.
2. DISASSEMBLY
FLEXIBLE CIRCUIT BOARD REPAIRING 2-1. Disassembly Flow ........................................................... 6
• Keep the temperature of soldering iron around 270 °C during 2-2. Side Panel (L)/(R) ........................................................... 7
repairing. 2-3. Top Panel Assy................................................................ 7
• Do not touch the soldering iron on the same conductor of the 2-4. Front Panel Block ........................................................... 8
circuit board (within 3 times). 2-5. Knob (VOL) .................................................................... 8
• Be careful not to apply force on the conductor when soldering 2-6. MAIN Board ................................................................... 9
or unsoldering. 2-7. Base Unit (BU-D1BD74UR) .......................................... 10
CAUTION 2-8. Optical Pick-up Block (DA11MMVGP) ........................ 10
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radia- 3. TEST MODE ............................................................ 11
tion exposure.
4. ELECTRICAL CHECKS ...................................... 13
This appliance is classified as
a CLASS 1 LASER product. 5. DIAGRAMS
This marking is located on the 5-1. Printed Wiring Board - CD Section - .............................. 18
rear exterior. 5-2. Schematic Diagram - CD Section -................................. 19
5-3. Printed Wiring Board - USB Section -............................ 20
5-4. Schematic Diagram - USB Section - .............................. 21
5-5. Printed Wiring Boards - MAIN Section - ....................... 22
5-6. Schematic Diagram - MAIN Section - ........................... 23
5-7. Printed Wiring Boards
- 2CH AMP/USB-JACK/JACK Boards - ....................... 24
5-8. Schematic Diagram
- 2CH AMP/USB-JACK/JACK Boards - ....................... 25
5-9. Printed Wiring Board - PANEL Board - ......................... 26
5-10. Schematic Diagram - PANEL Board - ............................ 27
5-11. Printed Wiring Board - PT-SWITCH Board -................. 28
5-12. Schematic Diagram - PT-SWITCH Board - ................... 29
6. EXPLODED VIEWS
6-1. Overall Section ............................................................... 32
6-2. Front Panel Section ......................................................... 33
6-3. Chassis Section ............................................................... 34
6-4. Top Panel Section ........................................................... 35
7. ELECTRICAL PARTS LIST .............................. 36
Accessories are given in the last of the electrical parts list.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
HCD-EC59
SECTION 1
SERVICING NOTES
MODEL IDENTIFICATION
NOTES ON HANDLING THE OPTICAL PICK-UP
- Back Panel -
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro- Model
static break-down because of the potential difference generated by Number
the charged electrostatic load, etc. on clothing and the human body. Label
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission, Model Part No.
observe from more than 30 cm away from the objective lens.
Argentina model 4-184-199-0[]
UNLEADED SOLDER Mexican model 4-184-200-0[]
Boards requiring use of unleaded solder are printed with the lead- African model 4-184-201-0[]
free mark (LF) indicating the solder contains no lead. 120V AC area in E model,
(Caution: Some printed circuit boards may not come printed with 4-187-950-0[]
Chilean and Peruvian models
the lead free mark due to their particular size)
: LEAD FREE MARK LASER DIODE AND FOCUS SEARCH OPERATION

Unleaded solder has the following characteristics. CHECK
• Unleaded solder melts at a temperature about 40 °C higher During normal operation of the equipment, emission of the laser
than ordinary solder. diode is prohibited unless the upper lid is closed while turning on
Ordinary soldering irons can be used but the iron tip has to be the SW305 (push switch type).
applied to the solder joint for a slightly longer time. The following checking method for the laser diode is operable.
Soldering irons using a temperature regulator should be set to
about 350 °C. • Method
Caution: The printed pattern (copper foil) may peel away if Emission of the laser diode is visually checked.
the heated tip is applied for too long, so be careful! 1. Open the upper lid.
• Strong viscosity 2. Push the SW305 as shown in Fig. 1.
Note: Do not push the detection lever strongly, or it may be bent or
Unleaded solder is more viscous (sticky, less prone to flow)
damaged.
than ordinary solder so use caution not to let solder bridges
3. Check the object lens for confirming normal emission of the
occur such as on IC pins, etc.
laser diode. If not emitting, there is a trouble in the automatic
• Usable with ordinary solder
power control circuit or the optical pick-up.
It is best to use only unleaded solder but unleaded solder may
In this operation, the object lens will move up and down 2
also be added to ordinary solder.
times along with inward motion for the focus search.
SW305
Fig. 1. Method to push the SW305
3
HCD-EC59
CAPACITOR ELECTRICAL DISCHARGE PROCESSING

When checking the board, the electrical discharge is necessary for the electric shock prevention.
Connect the resistors referring to the figure below.
• MAIN board (C622, C626)

Both ends of respective capacitors.
– MAIN Board (Conductor Side) –
C626 800 :/2 W
C622
800 :/2 W
MAIN BOARD SERVICE POSITION
• SIDE PANEL (L) was removed.
MAIN board
– Rear side view –
4
HCD-EC59
PT-SWITCH BOARD SERVICE POSITION
• SIDE PANEL (R) was removed.
PT-SWITCH board
BD74UR BOARD SERVICE POSITION
• SIDE PANEL (L) and (R) are removed, and the set is laid.
top panel block

BD74UR board
5
HCD-EC59
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. SIDE PANEL (L)/(R)

(Page 7)
2-3. TOP PANEL ASSY

(Page 7)
2-4. FRONT PANEL BLOCK 2-6. MAIN BOARD 2-7. BASE UNIT
(Page 8) (Page 9) (BU-D1BD74UR)
(Page 10)
2-5. KNOB (VOL)

(Page 8) 2-8. OPTICAL PICK-UP BLOCK
(DA11MMVGP)
(Page 10)
6
HCD-EC59
Note: Follow the disassembly procedure in the numerical order given.
2-2. SIDE PANEL (L)/(R)

4 two claws
2 two screws
(BVTP3 u 10)
4 two claws
1 three screws
(case 3 TP2) 3
5 side panel (L) 2 two screws

(BVTP3 u 10)
1 three screws
(case 3 TP2)
5 side panel (R)
2-3. TOP PANEL ASSY

6 Lift up the side of the top panel assy in the back and
remove the two claws in front of the top panel assy.
2 two screws
(BVTP3 u 10)
7 top panel assy

5 two claws
4 flexible flat cable (25 core)

3 connector (CN403)
(SW305)
1 screw
(KTP3 u 10)
1 screw
(KTP3 u 10)
7
HCD-EC59
2-4. FRONT PANEL BLOCK
3 screw (BVTP3 u 10)

4 lead wire (from USB board)

(CN607)
6 claw

(CN605)
8 front panel block
6 claw
5 three screws
(BVTT3 u 8)
2-5. KNOB (VOL)

Note: This illustration sees the front panel block from PANEL board side.
PANEL board
3 knob (VOL)
front panel block

(CN901)
hole
2 Push the knob (VOL) by flat-head screwdriver.
8
HCD-EC59
2-6. MAIN BOARD

6 connector
(CN603)
0 MAIN board (CN633)
7 fan motor connector

(CN601)
8 screw
(BVTP3 u 10)
4 connector
(CN604)
8 two screws
(BVTP3 u 10)
8 screw
(BVTP3 u 10)
9 lead wire
(from USB board)
3 connector
(CN609)

(CN607)
2 flexible flat cable
(9 core) (CN605)
:LUHVHWWLQJ
MAIN back
board panel
MAIN
board
9
HCD-EC59
2-7. BASE UNIT (BU-D1BD74UR)

Note 1: This illustration sees the top panel assy from base unit side.
4 two insulators
(blue)
1 four floating screws

(PTPWHM2.6)
7 base unit
(BU-D1BD74UR) 3 two insulators
(gray)
5 four claws
Note 2: Four claws might be fixed by bond.
Please fix four claws by the bond
when you replace the cover (D1).
2
6 cover (D1)
2-8. OPTICAL PICK-UP BLOCK (DA11MMVGP)
Note 1: When disconnecting the wire (flat type) (16 core) of optical pick-up block, solder the short-land.
5 tapping screw (P2)
7 optical pick-up block

(DA11MMVGP)
2 Solder the short-land.

Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the wire (flat type) (16 core).
6 shaft (support)
3 wire (flat type) (16 core) (optical pick-up)
4 BD74UR board block
1 Remove four solders.
10
HCD-EC59
SECTION 3
TEST MODE
COLD RESET CHANGE-OVER THE AM TUNING INTERVAL
The cold reset clears all data including preset data stored in the The AM tuning interval can be changed over 9 kHz or 10 kHz.
memory to initial conditions. Execute this mode when returning Procedure:
the set to the customer. 1. Press the [?/1] button to turn the power on.
Procedure: 2. Press the [FUNCTION] button to select TUNER AM function.
1. In the standby status, press the [?/1] button to turn the power 3. Press the [?/1] button again to turn the power off (standby).
on. 4. After pressing the [DISPLAY] button, while pressing the
2. Press three buttons of [x], [FUNCTION] and [?/1] simultane- [TUNING + M L] button, press the [?/1] button.
ously. 5. It turns power on and display “9k STEP” or “10k STEP”, and
3. When “RESET” appears, the set enters standby status. thus the tuning interval is changed over.
PANEL TEST MODE CD SERVICE MODE

Enter The Panel Test Mode This mode can move the SLED of the optical pick-up, and also can
Procedure: turn the optical pick-up laser power on and off.
1. In the standby status, press the [?/1] button to turn the power Procedure:
on. 1. Press the [?/1] button to turn the power on.
2. Press three buttons of [DSGX], [x] and [?/1] simultaneously. 2. Press three buttons of [u], [ENTER] and [?/1] simultane-
3. When the panel test mode is activated, LEDs and segments of ously.
the liquid crystal display are all turned on. 3. Press the [FUNCTION] button to select CD function.
4. It enters the CD service mode and displays “SERVICE”.
Version Check 5. To release from this mode, press three buttons of [u], [EN-
Procedure: TER] and [?/1] simultaneously.
1. In the panel test mode (all LEDs and segments of the liquid
crystal display are turned on), press the [FUNCTION] button. Key Operation:
2. On the liquid crystal display, date and version are displayed [TUNING + M L], [– TUNING l m]:
“xxxxxxxx”. Use these keys to move the SLED. When [TUN-
3. From this status, press the [u] button, and the destination and ING + M L] is pressed in this mode, the SLED
model name are displayed. moves to outer circumference and the message
4. To release from this mode, press three buttons of [DSGX], [x] “SLED OUT” is displayed.
and [?/1] simultaneously. When [– TUNING l m] is pressed in this
mode, the SLED moves to inner circumference and
Key Test Mode the message “SLED IN” is displayed.
Procedure:
1. In the panel test mode (all LEDs and segments of the liquid [CD]:
crystal display are turned on), press the [x] button. Use this key to turn the optical pick-up laser power
2. The message “KEY0 0 0” displayed. Whenever any buttons on and off. When the laser power is turned on, the
are pressed, the value is changed. message “LD ON” is displayed. When the laser
3. To release from this mode, press three buttons of [DSGX], [x] power is turned off, the message “LD OFF” is dis-
and [?/1] simultaneously. played.
CD POWER MANAGE
This mode is for switch the CD power supply on/off. Even if this
state pulls out AC plug, it is held.
Procedure:
1. Press the [?/1] button to turn the power on.
2. Press the [FUNCTION] button to select CD function.
3. Press the [?/1] button again to turn the power off (standby).
4. After pressing the [DISPLAY] button, while pressing the [x]
button, press the [?/1] button.
5. It turns power on and display “CD/USB”, then display “PWR
ON” or “PWR OFF”.
11
HCD-EC59
CD FACTORY MODE
Note 1: Do not enter the this mode while any other test mode is in prog-
ress.
Note 2: Do not enter any other test mode while the this mode is in prog-
ress.
Procedure:
1. Press the [?/1] button to turn the power on.
2. Press the [FUNCTION] button to select CD function
3. Press three buttons of [u], [USB] and [?/1] simultaneously.
4. It enters the CD factory mode and the message “FACTORY”
is displayed. When the [CD] button is pressed, the following
message (initial display) is displayed.
– ON
S character mode setting
Tracking servo setting
RF gain setting
Key Operation:
[CD]:
The display changes in the following order when-
ever the button is pressed.
(Initial display)
FCSAG ** (**: Focus AGC value)
TRKAG ** (**: Track AGC value)
RF_AG ** (**: RF AGC value)
[DSGX]:
RF gain setting changes whenever the button is
pressed.
“–”: No gain fixation.
“AL”: Fix to the gain for AL disc.
“RW”: Fix to the gain for RW disc.
[FUNCTION]:
S character mode setting changes whenever the but-
ton is pressed.
“ ”: S character mode OFF.
“S”: S character mode ON.
5. To release from this mode, press three buttons of [u], [USB]

and [?/1] simultaneously.
12
HCD-EC59
SECTION 4
ELECTRICAL CHECKS
CD SECTION TUNER SECTION 0 dB = 1 μV
Note: FM AUTO STOP CHECK

1. CD Block is basically constructed to operate without adjustment.
2. Use YEDS-18 disc (Part No. 3-702-101-01) unless otherwise indicat- signal
ed. generator
3. Use an oscilloscope with more than 10 MΩ impedance. set
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
5. Check the focus bias check when optical pick-up block is replaced. Procedure :
1. Turn the power on.
FOCUS BIAS CHECK 2. Input the following signal from Signal Generator to FM an-
oscilloscope tenna input directly.
(DC range)
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
BD74UR board
Deviation : 75 kHz
CL102 (RFOUT) + Modulation : 1 kHz
CL117 (VREF) – ANT input : 35 dBu (EMF)
Procedure : Note: Please use 75 ohm “coaxial cable” to connect SG and the set. You
1. Connect the oscilloscope to CL102 (RFOUT) and CL117 cannot use video cable for checking.
(VREF) on the BD74UR board. Please use SG whose output impedance is 75 ohm.
2. Press the [?/1] button to turn the power on, and press the
[FUNCTION] button to select CD function. 3. Set to FM tuner function and scan the input FM signal with
3. Set disc (YEDS-18) and press the [u] button to playback. automatic scanning.
4. Confirm that oscilloscope waveform is as shown in the figure 4. Confirm that input Frequency of A, B and C detected and auto-
below (eye pattern). matic scanning stops.
A good eye pattern means that the diamond shape (◊) in the
center of the waveform can be clearly distinguished. The stop of automatic scanning means “The station signal is re-
ceived in good condition”.
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
level:
1.1 ± 0.4 Vp-p
Checking Location:
– BD74UR Board (Conductor Side) –
CL117
(VREF)
IC301
CL102
(RFOUT)
IC101
13
HCD-EC59
SECTION 5
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards. For Schematic Diagrams.
Note: Note:
• X : parts extracted from the component side. • All capacitors are in μF unless otherwise noted. (p: pF) 50
• Y : parts extracted from the conductor side. WV or less are not indicated except for electrolytics and
• W : indicates side identified with part number. tantalums.
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise
(The other layers' patterns are not indicated.) specified.
• f : internal component.
Caution: • 2 : nonflammable resistor.
Pattern face side: Parts on the pattern face side seen • C : panel designation.
(Conductor Side) from the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
Note: The components identified by mark 0 or dotted
(Component Side) the parts face are indicated.
line with mark 0 are critical for safety.
Replace only with part number specified.
Caution:
Pattern face side: Parts on the pattern face side seen
(SIDE B) from the pattern face are indicated. • A : B+ Line.
Parts face side: Parts on the parts face side seen from • B : B– Line.
(SIDE A) the parts face are indicated. • Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Indication of transistor. – BD74UR Board –
no mark : CD PLAY
C – Other Boards –
no mark : TUNER (FM/AM)
Q These are omitted. • Voltages are taken with VOM (Input impedance 10 MΩ).
B E Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Q Voltage variations may be noted due to normal production
tolerances.
B C E • Circled numbers refer to waveforms.
• Signal path.
These are omitted. F : TUNER (FM/AM)
• Abbreviation J : CD PLAY
AR : Argentina model E : USB
E2 : 120V AC area in E model f : PC IN
E4 : African model • Abbreviation
E51 : Chilean and Peruvian models AR : Argentina model
MX : Mexican model E2 : 120V AC area in E model
E4 : African model
E51 : Chilean and Peruvian models
MX : Mexican model
14
HCD-EC59
• Circuit Boards Location
BD74UR board
MAIN board
REG board
PANEL board
JACK board
PT-SWITCH board
USB board
2CH AMP board
USB-JACK board
15
HCD-EC59
• IC Pin Function Description
USB BOARD IC901 LC87F1JJ2AU-SQFP-H (USB CONTROLLER)

Pin No. Pin Name I/O Description
1 P73 I/O Not used
2 RES I Reset signal input from the system controller “L”: reset
3 XT1 I Not used
4 XT2 O Not used
5 VSS1 - Ground terminal
6 CF1 I Main system clock input terminal (12 MHz)
7 CF2 O Main system clock output terminal (12 MHz)
8 VDD1 - Power supply terminal (+3.3V)
9 SO0 O Serial data output to the CD-MP3 processor
10 SI0 I Serial data input from the CD-MP3 processor
11 SCK0 O Serial data transfer clock signal output to the CD-MP3 processor
12 SO1 O Serial data output terminal Not used
13 SI1 I Serial data input terminal Not used
14 SCK1 O Serial data transfer clock signal output terminal Not used
15 P16 I Chip enable signal input from the CD-MP3 processor
16 P17 I/O Not used
17 MCLKI I Master clock signal input terminal Not used
18 MCLKO O Master clock signal output terminal Not used
21, 22 P00, P01 I/O Not used
23 to 25 DBGP0 to DBGP2 - Debug terminal
26 SDAT I Serial data input from the CD-MP3 processor
27 BCLK I Bit clock signal input from the CD-MP3 processor
28 LRCK I L/R sampling clock signal input from the CD-MP3 processor
29, 30 P20, P21 I/O Not used
31 P22 O Audio serial data output to the CD-MP3 processor
32 P23 O Request signal output to the CD-MP3 processor
33 P24 O Audio serial data transfer clock signal output to the CD-MP3 processor
34 to 36 P25 to P27 I/O Not used
37 UHD- I/O USB D- serial data input/output terminal
38 UHD+ I/O USB D+ serial data input/output terminal
41 UFILT - PLL filter circuit connection terminal for USB interface Not used
42 AFILT - PLL filter circuit connection terminal for audio interface Not used
43 P32 I/O Not used
44 URX1 I USB RX signal input from the system controller
45 UTX1 O USB TX signal output to the system controller
46 P70 I Request signal input from the CD-MP3 processor
47 P71 I Sleep control siganl input from the system controller
48 P72 I/O Not used
16
HCD-EC59
PANEL BOARD IC301 MB90F831PF-G-SPE1 (SYSTEM CONTROLLER)

Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 SEG32 O Segment drive signal output to the liquid crystal display 90 VCC - Power supply terminal (+3.3V)
2 O-SP-RELAY-ON O Relay drive signal output terminal (for speaker) 91 VSS - Ground terminal
3 O-POWER O Main power on/off control signal output terminal “H”: main power on 92 X1 I Main system clock input terminal (6 MHz)
4 O-5V-ON O CD and VBUS power on/off control signal output terminal “H”: CD and VBUS power on 93 X0 O Main system clock output terminal (6 MHz)
5, 6 NC - Not used 94 to 100 SEG25 to SEG31 O Segment drive signal output to the liquid crystal display
7 CDM-OPEN I Detection switch input from the CD lid open/close detect switch
8 NC - Not used
9 I-RMC I Remote control signal input from the remote control receiver
10 to 12 NC - Not used
13 X0A I Sub system clock input terminal (32.768 kHz)
14 X1A O Sub system clock output terminal (32.768 kHz)
15 VCC - Power supply terminal (+3.3V)
16 VSS - Ground terminal
17 O-CD-CE O Chip enable signal output to the CD-MP3 processor
18 O-CD-CL O Clock signal output to the CD-MP3 processor
19 I-CD-DI I Serial data input from the CD-MP3 processor
20 O-CD-DO O Serial data output for the CD-MP3 processor
21, 22 NC - Not used
23 O-CD-M-MUTE O CD motor drive on/off mute control signal output to the CD motor/coil driver
24 O-CD-RST O System reset signal output to the CD-MP3 processor “L”: reset
25 NC - Not used
26 O-CD-ON O CD power on/off control signal output terminal “H”: CD power on
27 NC O Not used
28 O-LED-LCD O LED drive signal output terminal for STANDBY indicater
29 I-USB-TXD I USB TX signal input from the USB controller
30 O-TP-REC-MUTE I Not used
31 O-USB-RXD O USB RX signal output to the USB controller
32 AVCC - Power supply terminal (+3.3V)
33 O-USB-SLEEP O Sleep control signal output to the USB controller
34 O-USB-RST O System reset signal output to the USB controller
35 AVSS - Ground terminal
36 I-P-MONI I Power monitor signal input terminal
37, 38 I-KEY1, I-KEY2 I Front panel key input terminal (A/D input)
39 I-TU-ANSD I Auto gain control signal input terminal
40 I-5V/9V-DET I Power supply voltage detection signal input terminal
41 I-KEY-WAKE-UP/VOL I Front panel key wake-up signal input/volume control signal input terminal
42 I-HOLD I Not used
43 NC - Not used
44 GND - Ground terminal
45 NC - Not used
46 I-MODEL I Model setting terminal
47 I-SUFFIX I Destination x setting terminal
48 I-TU-DO I Serial data input from the AM/FM DET
49 O-I2C-FUNC-DATA O Serial data output to the electrical volume
50 O-I2C-FUNC-CLK O Serial data transfer clock signal output to the electrical volume
51 MD2 - Not used
52 MD1 - Not used
53 MD0 - Not used
54 I-RST I Reset signal input from the voltage detect “L”: reset
55 O-TU-CE O Chip enable signal output to the AM/FM DET
56 O-TU-DI O Serial data output to the AM/FM DET
57 O-TU-CLK O Serial data transfer clock signal output to the AM/FM DET
58 VLCD - Terminal for doubler circuit capacitor connection to develop liquid crystal display drive voltage
59 to 62 COM0 to COM3 O Common drive signal output to the liquid crystal display
63, 64 SEG0, SEG1 O Segment drive signal output to the liquid crystal display
65 VCC - Power supply terminal (+3.3V)
66 VSS - Ground terminal
67 to 89 SEG2 to SEG24 O Segment drive signal output to the liquid crystal display
HCD-EC59
17 17
HCD-EC59
5-1. PRINTED WIRING BOARD - CD Section - • See page 15 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
BD74UR BOARD BD74UR BOARD
(COMPONENT SIDE)
M401
(SPINDLE) (CONDUCTOR SIDE)
+ –
B
C301 CL119
CL419
CL117 S001
(LIMIT)
CL420
SL304
C SL303 R305
R304
C303
C302
C304
+
28 22 30 21 15
SL302 SL301
IC301 M402
(SLED)
D CL201
C133 CL116
1 7 29 8 14
C116
CL118
X101
R303
CL101 CL121
R101 C132 R301
–
C117 R129 R302
R102 C101 R126
C128
CL102 C127
C130
C131
C102
R104 R131
R103 R416 CL416
CL209 C103 R415
CL415
E
C418
R105 80 61 R124
R106 1 60 CL414
1
CL115 CL413
CL210
R123
R107 C104 R414
C129
CL103 R122
R417
CL211 R108 CL114 R402

R413
CL212
C105 C118 IC101 R118 CL113 CL412
C113
C414 CL422
C106
R412
CL208 R109 CL112

R111 20 41 C126
CL207 21 40 CL418 USB
C402
CL111
C119
A
C413 R121
R112
CN403
BOARD
C404
C107
F R117 CL104 CL205 C121 C123
CL110
CL423 CL411
CN902
C122
C120 CL109
C125
R120
SL201 CL106 (Page 20)
R114
CL108 CL417
CL105
C108
CL408
C403
CL120
C401
R401
CL421
R116
C205
C111
C110
R113
C112
C203
R409
C207
25
C201 CL406
CL107 CL407
C206
CL204
G C407 R408
CL405
CL202 1 16 CL402
C209
CN201 CL213 R407

C124
R201
C208
R203
CL403
C406 R406
CL214 CL404
E C B
Q201
R405
R202
CL203
11 CL206
R403 CL401 R404
1-882-050- (11)
OPTICAL R411
CL409
H PICK-UP 11
BLOCK
(DA11MMVGP) 1-882-050- (11)
HCD-EC59
18 18
HCD-EC59
5-2. SCHEMATIC DIAGRAM - CD Section - • See page 24 for Waveforms. • See page 30 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
BD74UR BOARD
A C133
C132
0.1
R417
0
0.1
C131 C130 C127

0.1 0.1 0.1
0.047
C116 100 10V

R129 R131
100 0
CL118
X101
C117
16.934MHz
B CN201
C129 100 10V

16P C201
0.1
R126 0
VREF 16
0.1
VCC 15
CL121
CL116
CL212 CL213
C128
E 14 C203 C205 R201
10 10 1
CL211
D 13 CL214 C207
A 12
CL210 R202
2.2
C206
1 100
10V 2
CL209 3.2 CN403
B 11 25P
3.2 R416 100 CL416
1.6
1.6
1.6
1.6
3.2
3.2
1.4
1.6
3.2
1.6
3.2
CL208
C 10 1 PCMREQ
0
0
0
0
CL207 Q201 R415 100 CL415
F 9
1.6
2SA2119K
1 IC B/D 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
CL414
2
3
PCMDATA
PCMBCK
PCMDATA
GND 8
XOUT
DOUT
PCMLRSY
XIN
XVSS
CONT4
DVDD
DVSS
DVDD15
PCMREQ
PCMBCK
DVDD
SLCO
LRVSS
RCHO
LRREF
LCHO
LRVDD
XVDD
C OPTICAL
LD 7
CL206 R414 100 CL413
4 PCMLRSY
PICK-UP C209 Q201 C208 R101 330 CL101 1.6
EFMIN C2F(LRSY) 60 CL115 C418
VR 6 0.1 AUTOMATIC 1000p R203 1 100p 5 MGND
BLOCK CL205 POWER
0 CL102 1.6
RFOUT FSEQ(DATACK) 59 CL114 CL419
MD 5 2 6 MGND
(DA11MMVGP) CL204 CONTROL C102 0.01 C101 4700p 1.5
LPF DEFECT(DATA) 58 CL113 CL420
F+ 4 3 7 VM(7V)
CL203 C103 0.1 1.6 CL422 R402 0
T- 3 4 PHLPF TEST1 57 8 AVDD(3.3V)
CL202 R103 0 1.6 0 R124 10k R413 100 CL412
T+ 2 5 AIN AD_DATA(STDATA) 56 9 R-OUT
CL201 R104 0 1.6 0 R123 10k C414
F- 1 6 CIN AD_BCK(STCK) 55 10 DACGND
R105 0 1.6 0 R122 10k 2200p CL418
7 BIN AD_LRCK(STREQ) 54 11 DACGND
R106 0 1.6 C404 C402 C413
SP+ 8 DIN TEST0 53 100 12 DACGND USB
1 C104 0.1 1.7 0.1 10V R412 100 2200p CL411
D
9 SLCISET CONT0 52 CL112
13 L-OUT A BOARD
+
CL103 1.6
10 RFMON IC101 CONT1 51 CL111 C113
0.1
CL423
14 AGND CN902
C118 0.1 CL417
M401
(SPINDLE) M SL201
APC C105 0.01
CL117 3.2
11 VREF IC101
LC786950T-US-H
CONT2 50 CL110
C403 0.1 C401 100 10V CL421 R401 0
15 DGND (Page 21)
0.7 CL109
12 JITTC CD-MP3 PROCESSOR INTB1 49 16 DVDD(3.3V)
R108 1k C106 3300p 1.6 CL108 R121 10k R411 100 CL409
SP- 13 EIN INTB0 48 17 M-MUTE
–
2 R109 1k 1.6 3.1 R120 10k CL408

SL+ 14 FIN RESB 47 18 RESB
3 C107 0.1 3.1 3.2 R118 100 R409 100 CL407
15 PCNCNT DO 46 19 DO
+
CL104 1.6 3.1 R408 100 CL406

16 TE DI 45 20 DI
M402 C119 1.6 3.1 R407 100 CL405
(SLED) M 100
C108 0.01
17 TEIN CL 44
R406 100 CL404
21 CL
10V 3.2 0
18 LDD CE 43 22 CE
LIMIT-SW(CONT3)
STREQ(DEFECT)
CONT5(M-MUTE)
R112 0 0 C407 100p R405 100 CL403
SL- 19 LDS DVSS 42 23 STDATA
E
–
STDATA(C2F)
STCK(FSEQ)
4 3.2 C406 100p R404 100 CL402
20 AVSS DVDD 41 24 STCK
PDOUT1
PDOUT0
R403 100 CL401
DVDD15
PCKIST
C126
VVDD1
VVDD3
VVSS1
VVSS3
25 STREQ
SPDO
DVDD
SLDO
DVSS
AVDD
0.1
FDO
TDO
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
0
0
0
3.2
1.6
1.6
1.6
1.6
2.4
1.1
3.2
3.2
3.2
1.6
3.2
680 CL105
CL106
CL120
CL119
C123
680
10k
68k
22k
0.1
F R117
10k
C124
R102
R107
R113
R114
R111
100
10V
SL304
FDO
CL107
S001
SL303 (LIMIT)
TDO R116
68k
0.022
C122 C125
0.22
0.1
0.1 0.1
C110
C112
C111
G R305
8.2k
C304
0.1
R304
10k
C301 C120 C121
C303 C302 220 0.1 0.1
0.1 0.1 10V
3.5
3.5
1.6
3.2
7.6
7.6
1.6
3.5
3.5
28 27 26 25 24 23 22 30 21 20 19 18 17 16 15 IC B/D
IN4’
IN3’
GND
VO4-
VO4+
IN4
BIAS
VCC
GND
VCC
IN3
VO3+
VO3-
RESETt
OPIN
IC301
H IC301
BA5826HFP-E2
REGOUT
OPOUT
FOCUS/TRACKING
RESET
REGB
MUTE
VO1+
VO2+
VO1-
VO2-
GND
GND
GND
COIL DRIVE,
IN2’
IN1
IN2
SPINDLE/SLED
1 2 3 4 5 6 7 29 8 9 10 11 12 13 14 MOTOR DRIVE
0
3.5
3.5
1.6
7.6
1.6
3.5
3.5
R302
SP- 33k
R303 SL302
SP+ 12k SLDO
R301 SL301
I 5.6k SPDO
SL+
SL-
HCD-EC59
19 19
HCD-EC59
5-3. PRINTED WIRING BOARD - USB Section - • See page 15 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
(Page 26)
PANEL BOARD
A CN451
B
USB BOARD (SIDE A) USB BOARD (SIDE B)
B CL920 CL912 CL911
CL909
CL921
CL918 CL910
CL930 CL916
C
CL931
24 2
CL901
CN901
25 1
CL902
CL915
CL917
25
24
D C900 CL936 CL925 CL923
R900
CL919
6 2
(CHASSIS) CN910 (NC)
C906
C905
C907
7 1
W962
(Page 18)
R914
C908
R912
R910
CL926 CL924 CL922
BD74UR
A
CN902
E BOARD
R913
R908
R911
R909
R905
R907
R906
CN403
CL906 CL905
CL913
C909 CL904
CL914
CL908
C903
CL927
CL907
R904
F CL929
25
24 13
12
X901
CL903
2
R903
C904
IC901
1
CL928 CL932
C902
C915
R915 36 1 R901
37 48
C916
R916 R902
G C917
R917 C952 C951 C901
C953
R955
R922
R923
R921
R924
R954
R953
C954
C918
W961
R918
C955
C921
C919 R952 R951

R919
CL933
H C920
CL935 CL934
R920
C950
4 1
11 11
CN903
1-881-331- (11) 1-881-331- (11)
I
C
USB-JACK BOARD
CN561
(Page 24)
HCD-EC59
20 20
HCD-EC59
5-4. SCHEMATIC DIAGRAM - USB Section - • See page 24 for Waveforms. • See page 16 for IC Pin Function Descriptions.
1 2 3 4 5 6 7 8 9 10
USB BOARD CN903

4P
1 VBUSGND
A C950
0.1
R951
15k
CL934
CL935
2 D+
C
USB-JACK
BOARD
R952 3 D- CN561
15k
4 VBUS5V (Page 25)
R953 R954
C951 33 33
5p
C953 C954 C952

0.1 2.2 5p
50V
CL901 CL902
CN901 R922 100 C955
25P 2.2
R923 100 CN902
VBUS5V 1 R921 25P
R924 100 100 CL927
VBUS5V 1 STREQ
B
2
R955 CL928
VBUS5V 3 0 2 STCK
CL929
VBUSGND 4 3 STDATA
CE
VBUSGND 5 4 CE
C921 CL
3.1
2.9
2.5
1.8
3.3
VBUSGND 6 100p 5 CL
0
0
CL903 DI
USB-RST 7 48 47 46 45 44 43 42 41 40 39 38 37 6 DI
CL904 DO
USB-RXD 8 7 DO
AFILT
UFILT
P72
P71
P70
UTX1
URX1
P32
VSS3
VDD3
UHD+
UHD-
CL905 C901 RESB
USB-TXD 9 R901 8 RESB
0.1 C920 47p M-MUTE
CL906 100
USB-SLEEP 10 1 P73 P27 36 9 M-MUTE
CL907 CE 3.1 C918 47p
CD-CE 11 2 RES P26 35 10 DVDD(3.3V)
CL908 CL 3.3
CD-CL 12 XT1 P25 34 11 DGND
C R902 3
PANEL DI 0 R920 47 (Page 19)
BOARD B CD-DI 13
CL909
DO
100
C902
22p
4 XT2 P24 33
0 R919 47 L-OUT
12 AGND BD74UR
CN451
(Page 27)
CD-DO 14
CL910
CL911 RESB 1.5
5 VSS1 IC901 P23 32
0 R918 47
13 L-OUT A BOARD
CN403
CD-RST 15 X901 R903 6 CF1 P22 31 14 DACGND
12MHz IC901 C919 47p
CL912 M-MUTE 1M 1.8 LC87F1JJ2AU-SQFP-H
CD-M-MUTE 16 R900 7 CF2 P21 30 15 DACGND
0 C903 22p R904 0 3.3 USB CONTROLLER
CL913
DVDD3.3V 17 8 VDD1 P20 29 16 DACGND
CL914 R905 100 3.1 0 R917 100 R-OUT
DGND 18 9 SO0 LRCK 28 17 R-OUT
CL915 C905 R906 100 3.2 0 R916 100
AGND 19 100p 10 SI0 BCLK 27 18 AVDD(3.3V)
CL916 L-OUT C900 R907 100 3.1 0 R915 100
CD/USB-Lch 20 11 SCK0 SDAT 26 19 VM(7V)
100 0
CL917 16V C907
11
47p
47p
47p
AU-GND 21 100p 12 SO1 DBGP2 25 20 MGND
CL918 R-OUT R913 R914
MCLKO
DBGP0
DBGP1
CD/USB-Rch 22 21 MGND
D
MCLKI
100 100k
VDD2
SCK1
VSS2
CL919 CL930
C915
C916
C917
P16
P17
P00
P01
C904 C906
SI1
AVDD3.3V 23 0.01 22 PCMLRSY
100p
CL920 CL931
CD-VM7V 24 13 14 15 16 17 18 19 20 21 22 23 24 23 PCMBCK
CL921 CL932
CD-M-GND 25 24 PCMDATA
3.3
0
0
CL933
25 PCMREQ
C908 R908 R909 R911
100p 100 100 100
C909
0.1 R910 R912
100k 100k
DO
CE
CL
DI
W962
(CHASSIS)
CN910
7P
CL922
TRESET 1
CL923
DBGP0 2
F DBGP1 3
CL924
CL925
(NC) GND 4
CL926
DBGP2 5
VDD 6
CL936
VDD 7
HCD-EC59
21 21
HCD-EC59
5-5. PRINTED WIRING BOARDS - MAIN Section - • See page 15 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10
MAIN BOARD
A
D801
TP804 FL801
CN801 3
ANTENNA C815 JR602 JR601
R811
FM/AM
IC801 C816
JW632
1
1 30R809 C859
TP805
L802
L803
D802 L801
R808 C820 (Page 24)
R806
B C814 TP801
15 16
X801
K 2CH AMP
BOARD
C811 CN100
TP802 R807
TP803
C822 C812 JW634 R801
C813 TP662
JW633 R803 TP664 25
C810 CN603 24
R802 R684 R681
5 TP617 C639 TP663
R804 4 TP665
C821 R805 R810 TP618 TP619 R880
C699 C633 C640 R787 TP667 TP666
JW657 JW628
(Page 24) R881
C788
C853 C854 TP668 TP661
C685 R751
C638
C637
C634
JW635 2 TP615
2CH AMP 1 C700 C663 C684 R788
BOARD
W102
J JW643
LP003
R752 C674 IC601 C649 R700
R704 JW639
TP669 TP660
C789
R749 C650 C656 TP670
C687 JW658 17 16
C M601
M JW617
JW619 R754
R750
C655 TP672
CN607
TP671
TP673
(FAN)
R731
C641
C664
C686 R753
C662 C855 R697
JW653
TP674 D
LP002 C645 TP675 PANEL BOARD
CN601 R689 C632 R690
D628 D631 C713 JR603 C648 C856 JW652 CN301
1 3 C630 C667 TP677
C658
R732 R677 R715 R706
TP707 C771 JW612 E R707 32 1 C666 TP678
(Page 26)
Q618 B C694 R698
R733 JW618 R685 R687 JW616 R705 R709
R736 B C E TP706
E Q606 R678 C657 C647 2
R613
R614
R628
1
Q731
R772
5 CN633 1 JW615
R620 B D617 R676
JW642 C661 R702 R701 JW638 REG BOARD
R773 R882 R771 R658 C696 JW650
Q771 E B Q770 E R652 C619 JW649 TP679 TP676
E
B Q741 B E R774
TP623
C612
C611 B
Q605 R670 E
Q611
JW608 IC690 W690
C695
JW637
JW640
JW646
R662 B C698
D R737 D732 R738 D735 R775 R646 R637
TP624 D602 Q612 1 1
C776 R621 E
R776 D606 JW655
E C732 B
Q732 B JW614 R669 C629 3
B Q772 TP622 R644
E TP621 JW651 JW626 JW636 2 3
C773 JW601
JW654
TB602 D731 D605 JW656 C621 C697 11
R735 CN604
JW641
JW647
JW644
R734
SPEAKERS R666 R616 R622 R618

C731 3 TP633 1-882-030- (11)
IMPEDANCE: USE 6: JW606 R686
R642 D608 8 CN609 C631
JW603 R619
D601 1
R L R667 JW613
JW648 R624 JW661
C618 R727
D610 R625
R647 JW660 C762
TP626 C617 C623
R693 JW659 C760
R688
+ + L603 R768
R641 JW602 D791 D614 R692
E
R673
JW604 JW624 JW645 R760 TP631
TP625 R611 E
C626 R742
B D607 Q706 C715 TP630
C620 Q608 E R741
C609 C860 CN605
1 R794 R762 B E B R723
TP628 JW621 Q710 1
– – R781 R761 R767 2
R638 R791 JW611 B
C610 Q709 R764 B
TP632
R651 R728 TP627 D612 E E C761
R672 D609 Q707 C852
R649 R792 R763 C863
R650 C642
R645 TP629
R793
R879
R674 N
RY602
R648 R643 JW607 FB601
B Q619
D611 C764
R795 IC701 R765
JW627 JACK
D604 JW620 5 4 R655
E C765 D701 JW622 8 BOARD
R609 R639
B E
R691 R623 R797 1 9 CN496

R610 R640 R657
R798
C607 JW609 R617 R796 8 R675 TP635
C608 Q604 C622 JW625 (Page 24)
JW610 L701 JW631
JW623 B
JW605 R615 E Q708 TP634
F
R782
C766
C763
R770
R656
JW630 R799
JW629
11
R612 C627 C862 1-882-033- (11)

JW662
C628
ET601 C861 ET602
L604
RY602 PT-SWITCH
G (CHASSIS) BOARD
W052
E (CHASSIS)
(Page 28)
HCD-EC59
22 22
HCD-EC59
5-6. SCHEMATIC DIAGRAM - MAIN Section - • See page 24 for Waveforms. • See page 30 for IC Block Diagrams.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
MAIN BOARD
A CN801
3P G
TP805 R809 C859 C820 R807 X801
BPF 22k 0.1 22 180k 32.768kHz
AM 1 50V
I O
ANTENNA R698 R705 R701 R702 C699 C700
FM/AM GND 2 FL801
TP804 R801 C657 22k 22k 4.7k 4.7k 1000p 1000p
1k 1000p
FM 3 I-TU-DO
R802 1k O-TU-CLK C647 1000p
R806 R709
10k R803 1k C666 1000p 0
O-TU-DI
C816 L802 L801 C645 1000p R697 0
0.1 39nH 39nH O-TU-CE
B R804
1k
C655 220p R704 4.7k
C649 220p
21 C639, 640
1500p (EXCEPT E4)
R700 CN607
0.8
4.4
4.5
4.5
4.5
3.3
3.3
4.5
1.9
R774 R775 Q731 D801 C639 4.7k 25P
0
KTA1266GR-AT 2700p (E4)
10k 220k MC2840-T112-1 O-TU-CE TP662
CN601
3P FAN MOTOR DRIVE 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 25 O-TU-CE
IC B/D O-TU-DI TP663
TP706 R787
CL
FM ANT
FLL CAP
GND4
SD ADJ
L2
VREF3(4.3V)
L1
GND3
VREF2(3.3V)
DO
DI
CE
ST ADJ
CLK IN
0 20.4 C854 24 O-TU-DI
15k C650 C656 C855 C856 C648 TP664
M
VDD+ 1 O-TU-CLK
VREF1(4.3V)
M601 C640 R788 1 1 1 1 1 1
IC801
TP707 R733 R732 R731 23 O-TU-CLK
VCC LOW
(FAN)
MPX OUT
R773 R736 15k C658 TP665
GND 2 I-TU-ANSD
GND AM
AM AGC
D732 15 15 15
AM REF
SD OUT
AM ANT
AM LCF
ST OUT
220k 10k 1
R-OUT
L-OUT
MAZ8100GMLS0 22 I-TU-ANSD
GND1
AM Vt
TP666
C
VCC
VDD+ 3 20.3 AM/FM DET, OSC, C853 I-TU-DO
D802 MIX, PLL, IF AMP 21 I-TU-DO
Q771 MC2840-T112-1 1
TP667
2SC3052F-T1-LF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 IC801 20 O-FUNC-DATA
PROTECT DETECT R737 LV23401V-N-TLM-H TP668
Q772 4.7k L803 19 O-FUNC-CLK
0
2SC3052F-T1-LF
2.3
2.3
4.3
3.2
3.2
1.9
3.2
8.6
R772 0 AM ANT O-POWER TP669
12k PROTECT DETECT 18 O-POWER
TP801
TP802
TP803
0.7 TP661
8.9 Q732 3 4 17 O-SP-RELY
D735 2SC3052F-T1-LF R805
MA2J1110GLS0 TP660
100
0 20.3 FAN MOTOR DRIVE I-TU-ANSD 16 D-GND
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
C771 TP670
1 C822
0 2 5 1 IC B/D 15 CD/USB-L
D (Page 27)
50V 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 TP671
R735 14 CD-A-GND
C814
IC601
TP672
D
MAZ8043GMLS0
NC
NC
NC
NC
TRE-R
0.7
TRE-L
SEL-R
TUNER-R
VOL-R
SEL-L
TUNER-L
VOL-L
CD/USB-R
CD/USB-L
PC-IN-R
PC-IN-L
4.7k 1
1 6 13 CD/USB-R
50V TP673 PANEL
D731
C821
BASSA-R
BASSB-R
BOARD
BASSB-L
BASSA-L
1 ELECTRICAL VOLUME, 12 9V
SDATA
OUT-R
0 INPUT SELECTOR CN301
OUT-L
SURR
SCLK
R882 R771 C773 C776 R776 R738 C732 R808 C815 R811 C813 C812 C811 C810
SB-R
SB-L
GND
VCC
22 22 47k 0.1 470 11 CD-M-GND
470 10 0 0.1 33k 0.047
FIL
NC
NC
100 1000p 4.7 IC601 TP674
16V 50V 50V 10V BD3491FS-SE2 10 CD-AVR
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 I-P-MONI TP675
C731 R734 9 I-P-MONI
Q770 R810 TP676
2SC3052F-T1-LF 4.7 47k 10 O-CD-ON/5V-ON
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.1
8.3
3.2
3.2
4.1
TB602 8 O-5V-ON
PROTECT DETECT 50V TP677
SPEAKERS 7 VSTBY
IMPEDANCE: USE 6: D601 Q604 TP678
MC2838-T112-1 2SC3052F-T1-LF 6 VBUSGND
R612
E 0
10 D604 R638 R641 R642 RELAY DRIVE
47 47 47 5 VBUSGND
R L RY602 MA2J1110GLS0
0.8
C674 4 VBUSGND
R609 R610 TP679
R749
R750
4.7k
4.7k
4.7k 4.7k Q608 0.022 R707
3 VBUS5V
TP626 L604 2SC3052F-T1-LF 220
+ + STANDBY SWITCH R645 2 VBUS5V
4700p
4700p
C788
C789
TP625 2.2k
R706 VBUS5V
17.1 2.5 1
C634
C637
C638
0.047
0.047
0.047
C685
C687
0.068
0.068
220
L603 C617 C607 R639 R640 C633
0.1 0.1 100k 100k R667 0.047 C684 R751
- - 0.068 C663
47k 5.6k CN605
O-POWER 3.1 1 R880 9P
50V 100 TP630
F R611
10
C618
0.1
C608
0.1
R666
1k
C686 R753
1 AUDIO-L
D614 2 A-GND
MA2J1110GLS0 0.068 5.6k C664
1 TP631
R881 3 AUDIO-R
N (Page 25)
C610 C609 R647 R615 R643 C630 50V 100
4700p 4700p 10 10 10k 47
4 HP-GND
10V TP632
5 HP-L JACK
TP633
6 HP-R BOARD
R613 R614
TP634 CN496
10k 10k Q605, 606 7 AMP-ON
AC DETECT TP635
D791 8 SP-RELAY
MA2J1110GLS0
G Q605
2SC3052F-T1-LF
Q606
2SC3052F-T1-LF
R752
5.6k
R754
5.6k
C713
470p
R715
100
9 GND
C662 R681 R684 C667 C661 C694 R662 R658 R674 R675
R646 8.9 8.9 1000p 470
3300p 22k 22k 220 10 470 47 47
100 16V 50V 2W 2W
CN633
0 R644 5P
1k
0
1 PA-GND
R648
47k
R651
4.7k
R728
4.7k
TP620
TP622
2 LOW-OUT-R J (Page 25)
3 +VH
TP623 2CH AMP
H R652
100
TP624
4 -VH BOARD
W102
D602 D606 R791 5 LOW-OUT-L
MC2838-T112-1 MC2836-T112-1 R650 R727 100k
4.7k 4.7k
C695 C696 C620 R649 R792 CN603

C611 1 1 100 2.2k 220k 5P
0.22 10V TP615
D631 1 IN-R
MA2J1110GLS0
K (Page 25)
O-POWER
O-CD-ON/5V-ON
I-P-MONI
2 A-GND
R620 TP617
MA2J1110GLS0
4.7k 3 IN-L 2CH AMP
TP618
I
D605
4 AMP-STBY BOARD
C612 TP619 CN100
R672 5 OVERLOAD
0.22 10k
Q706 C762
Q706-710 KTA1273-Y-AT L701 R767 1000
DC/DC CONVERTER 100uH 3.3 6.3V C862
20.4 5
R621 0.01
4.7k
R693 R794 R761 C715
1k 5 0.1 R723 R688
10k 470
ISA1235AC1TP-1EF
R616 R617 R618 R619 R687 0.9 R796 Q707 20.4 5 2.2 470
3.9k 10k 10k 3.9k D608 22k R685 330k R797 KTA1273-Y-AT
1N5402-C532-2 4.7k 47k 20.4 5
Q710
R741 R673 ET601
J
0 0.9 2.2 470
R622 R623 R624 R625 R762
CN604 33k 10k 10k 33k D607 D617 Q709 470
E
8P 1N5402-C532-2 MC2838-T112-1 2SC3052F-T1-LF
0
VH(AC) 8 Q612 4.5 R742 ET602
REG BOARD
C621 C622 ISA1235AC1TP-1EF R678 R765 R793 R763 R764 R879 R781 2.2
0.1 3300 R676 47k D628 3.3k 3.3k 3.3k 3.3k 100 100k
20.4
VL(AC) 7 PROTECT DETECT
2.5
0.5
0.9
E
50V 10k MA2J1110GLS0
E GND
VL(AC)
6
5
C860 C623
D609
C626
3300
C861
0.01
C628
1000
C627
2200 9
C629
4700p
R669
4.5 0 R690 R692 8 7 6 5 R760
2.2
(CHASSIS)
W690
0.01 0.1 100k Q618 2.2k 4.7k 20.4
PT-SWITCH 1N5402-C532-2
REF
CT
CS
V+
50V 25V 25V ISA1235AC1TP-1EF IC B/D 3P 1
VH(AC) 4
BOARD TP629 PROTECT DETECT C698
W052 AC DETECT 3 8.9 R768 IN 1
0.1 I
R637 10k
IC701
TP628
K (Page 29)
D610
GND
OUT
V STBY 4.7k Q708 G
2 0 20 GND 2
IN-
1N5402-C532-2
FB
TP627 2SC3052F-T1-LF 3
D611 C697
RELAY ON/OFF 1 1N4002-A2 DC/DC CONVERTER 0 OUT 3 O
JW630 1 2 3 4 0.1
IC701 2
R686 NJM2368V(TE2)
R655 9
56k
0.5
0.5
0.3
C642 R798 10k
0.022 4.7k
Q611
2SC3052F-T1-LF
C763
R657 IC690
PROTECT DETECT 68k
D612 R670 470p +9V REGULATOR
1N4002-A2 10k 8.9 0.3 C764
JW629 IC690
10 KIA7809API-U/PF
RB055L-40TE25
0 0.8 50V C766 R782 R770 R656
4700p 10k 100k 1k
D701
R628 C619 C631 R677 C632 C641 R689 R691 R795 C765 C760 R799 C852 C761 C863
L 10k 0.01 100
16V
10k 4.7
50V
3.3
50V
27k 10k 180k 1000p 470
25V
560 0.01 470
16V
0.1
CN609
3P
FB601
Q619
2SC3052F-T1-LF 1 IN
MAIN POWER 2 GND
ON/OFF CONTROL
3 OUT
HCD-EC59
23 23
HCD-EC59
• Waveforms 5-7. PRINTED WIRING BOARDS - 2CH AMP/USB-JACK/JACK Boards -

• See page 15 for Circuit Boards Location. • : Uses unleaded solder.
– BD74UR Board – – USB Board – – PANEL Board –
1 IC101 2 (RFOUT)
qa IC901 7 (CF2) ea IC301 qf (X1A) 1 2 3 4 5
(CD play mode)
(Page 22) (Page 20)

J MAIN BOARD
CN633 C USB BOARD
CN903
A 2CH AMP BOARD USB-JACK BOARD

2.8 Vp-p 3.1 Vp-p
0.7 to 1.5 Vp-p 30.8 Ps CN561
83.3 ns
1 4
TP105
200 mV/DIV, 500 ns/DIV 1 V/DIV, 20 ns/DIV 1 V/DIV, 20 Ps/DIV 5 W102 1
A102
C164 TP102 TP561
TP559 TP562
C160
IC101 us (XOUT) IC301 os (X1)
2 es
TP104 TP103 TP101 TP560
C565 C561
JW201
C162
IC102 R162
R160
JW560
B 1
JW202 JW203 E
B
Q141
R141 C141
R561R562 FB561
B FB562
2.8 Vp-p 3.3 Vp-p R111 C142 Q142
R142
E
59.1 ns 168 ns R145

R112 C165 R146 4 1
CN560 11
1 V/DIV, 20 ns/DIV – MAIN Board – 1 V/DIV, 100 ns/DIV C161
R144 R143
R161 1-882-031- (11)
R163 D141
IC801 qh (CLK IN)
wa R119 JW204 C163 JW205
C107
R113
R115
C C111
D140
R109
C105
C109
15 TP108
JACK BOARD
C106
Approx. C101 R103
R114 R105
R107 J491 TP492
30.5 Ps 304 mVp-p C108 R108
C103 TP111 TP110 PC IN CN496
9
8
R110
R116 C104
R106 CN100
C102
200 mV/DIV, 20 Ps/DIV C112 R104
4
5
2
1
TP493
N
R120 TP112 11 R478 TP491 MAIN BOARD
C110
TP109 1-882-028- (11) R477 2 CN605
C491
1 (Page 22)
JW492
K MAIN BOARD JW491

D CN603
(Page 22) TP494
TP495
J492
PHONES C496
TP498
C495
TP497 TP496 11
1-882-029- (11)
HCD-EC59
24 24
HCD-EC59
5-8. SCHEMATIC DIAGRAM - 2H AMP/USB-JACK/JACK Boards -

1 2 3 4 5 6 7 8 9 10 11 12 13
2CH AMP BOARD USB-JACK BOARD

A IC102 CN561
2CH POWER AMP 4P
ST-BY
FB561
+VCC
-VCC
-PRE
TP562
C
IC102 R562 0 CN560
+PRE SUB GND VBUS5V 4
STK433-040 TP561 2.2 1 4P
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 D- 3
TP560 2
USB
D+ 2
BOARD
0
3
32
2.1
-34
33.7
-32.2
TP559 R561
CN903 VBUSGND 1 C565 C561
2.2 1 220 4
(Page 21) 10V
B FB562
0
R111 R112 C105 C106

0.22 0.22 100p 100p
2W 2W
W102 R109 R110
5P 470 470
TP105
LOW-OUT-L 5
J -VH 4
TP104
MAIN +VH 3
TP103
TP102
JACK BOARD
BOARD C107
C
LOW-OUT-R 2
CN633 TP101 3p
J491
(Page 23) PA-GND 1
R143 R141
CN496
9P PC IN
D141 22k 1.2k R478 R477
R113 TP491
MC2838-T112-1 22k 22k
47k AUDIO-L 9
TP492
R160 R161 A-GND 8
R145 220 220 TP493
2.2k R114 R115 R116
0 0 AUDIO-R 7
N
47k 1.5k 1.5k TP494
R162 R163 HP-GND 6
Q141 C141 220 220 TP495
2SA2026 0.1 C108
3p MAIN HP-L 5
OVERLOAD DETECT 0 TP496
C109 C110 BOARD
D R119
100
47
25V
47
25V
CN605
HP-R
AMP-ON
4
3
TP497
J492
R144 R142 C160 C161
(Page 23) TP498 C496 C495 C491
1000p 1000p 0.1 PHONES
22k R146 1.2k 0.1 0.1 C111 SP-RELAY 2
2.2k 4700p C103 C104
0 0 470p 470p GND 1
C164 C165
Q142 C142 0.1 0.1
2SA2026 0.1 R107 R108
47k 47k
OVERLOAD DETECT 0
D140 C162 C163 C101 C102

MA2J1110GLS0 100 100 1 1
50V 50V 50V 50V
CN100
5P
R103 R105 R106
TP108
E OVERLOAD 1 2.2k R120 2.2k 2.2k
K TP109 1k
AMP-STBY 2
TP110
IN-L 3 C112
MAIN TP111 0.1 R104
BOARD A-GND 4 2.2k
CN603 TP112
5
(Page 23) IN-R
HCD-EC59
25 25
HCD-EC59
5-9. PRINTED WIRING BOARD - PANEL Board - • See page 15 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7 8
PANEL BOARD
A
37 1
R498
JW304 JW305 3 1
E B R328 LCD301 JW309 R497

X302 C342 R402
81 80 LIQUID CRYSTAL DISPLAY
Q301 R326 C497 JW377
C341 R305
R327
JW360
R381
JW303
JW312
R304
R303 IC302
D306
(STANDBY) JW315 R337 TP376
100 R401 JW378 TP378
C340
B C317 R310
R313 R400 JR306
JR309 TP372
2 10
TP380
JW376
1 51 TP373
SW305 TP341
R324 IC301 JW366 TP374 JW374 1 CN305 11
TP379
R370 JW328 TP371 TP377
(CD LID OPEN/CLOSE DETECT) 50
X301 JW382
JW365 TP375 (NC)
2 C319
R363 JW362 R307
1 C320 R396
C321 C306
W305 R321 R391
R320 30 31 C305
R319
R318 R392 R378
C330 R382 R376
JW363
R312 R302 C332 R306 C336 R390 R383
JW361 R315 R420 R434 R379 JW367
C JW359
R499
R308
R419 JW341 C338
JW358
JW348
JW347
R311 R377 R309 D304 R471
JW357
JW351 JW350
JW356 R470
JW349
JW343
JW342
JW340
JW339
JW338
JW345
JW375
JW355
JW344
JW346 JW337
R480 JW353 JW354
SW482 SW481 JW308
R491 R490
USB CD JW352 JW364
R481
SW471 SW491
R375 R492
FUNCTION 1
R487 JW326 JW327
D SW483 R486 C356 D303 R334
R335
R336
JW386
SW472
JW322 JW336
ENTER REC TO USB
JW325 C304 JW335
B E Q306
R472
D302 JW334
C303
C302 JW324 JW333
R464 C462 R333
R485 R466 R462 JW332 R473
Q303 E B
SW484 R460 R458 SW473
+ TP329 JW331 –
EC B
D301Q305 B E B E Q304
JW323 Q302 JW330
R332
TP327 R431 R384 R330 JW329
R331 R329
E D453
TP314
TP335 JW371
C301
R494 R430 R429

R484 TP331
TP333 R496 TP305
JW321 C454 R495
2 24 R493 D400 TP303
R450
JW320 1 3 R474
C452 1 CN451 25
SW485 JW307 JW301 SW474
TP338 TP337
JW302
JW306
x u
JW313
JW311
TP336 JW368 TP330
JW319
TP301
TP310
TP309
TP307
TP306
TP304
S491
JW318
JW317
JW316
TP313 TP334
JW369 TP328 TP326 JW310 TP315 TP312
R452 C451 C453
Q452 E B JW314 R465
TP321 TP311
R449 TP319 TP318
F R482
R451 D451 R453
D452
R461
R463
TP332
ROTARY ENCODER 24 2
R373 R459 VOLUME
TP322 25 1
SW486 CN301
JW372 TP320 R475
B
TUNING + C450 TP317 TP302

C
ML JW370
R456 R455 R454 TP316
E
Q451
USB BOARD
CN901 B MAIN BOARD
CN607 D SW475
– TUNING
R483
(Page 20) (Page 22) lm
R476
G SW487 SW476
OPTIONS DSGX
SW471 – 476,
SW481 – 487, 491
11
1-882-026- (11)
HCD-EC59
26 26
HCD-EC59
5-10. SCHEMATIC DIAGRAM - PANEL Board - • See page 24 for Waveforms. • See page 16 for IC Pin Function Descriptions.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
SW305
PANEL BOARD
A CD LID
SEG32
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
OPEN/CLOSE
DETECT W305
2P
GND 1 X302
TP341 6MHz
C306 C341 C321 C342
CD-OPEN/CLOSE 2 470 0.1 0.1 1000p
6.3V
R381
1k
Q302 R336
32
I-RST
I-HOLD
B 8.3
KTA1271Y-AT
4
10k
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.5
3.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
1.2
D303
MC2836-T112-1
R326 R329 R331 R333 R363 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
100 2.2k 100k 100k R375 22k
47
VCC
SEG31
SEG30
SEG29
SEG28
SEG27
SEG26
SEG25
SEG24
SEG23
SEG22
SEG21
SEG20
SEG19
SEG18
SEG17
SEG16
VSS
7.7
X0
X1
R327 R332 R334 1.2 1.2 SEG15
100 10k 3.3k R335 R313 1 80
Q303 100 SEG32 SEG15
22k O-SP-RELAY 3.2 1.2 SEG14
CN301 2SC3052F-T1-LF 2 79
6.1 Q302, 303 O-SP-RELAY-ON SEG14
25P O-POWER R310 100 3.2 1.2 SEG13
+4V REGULATOR
TP303 O-TU-CE 4.6 3 O-POWER SEG13 78
C
O-TU-CE 1 C304 3.2 O-5V-ON 0 1.2 SEG12
TP304 O-TU-DI D306 4 O-5V-ON SEG12 77
1L0341Y23E0CA602-II 0.1
O-TU-DI 2 0 R324 1.2 SEG11
TP305 O-TU-CLK (STANDBY) 4 100 5 NC SEG11 76
R370
O-TU-CLK 3 1k 1.2 SEG10
TP306 I-TU-ANSD 3.1 6 NC SEG10 75
D301 Q306
I-TU-ANSD 4 MAZ8043GMLS0 0 1.2 SEG9
TP307 I-TU-DO 0 RT1N441C-TP-1 7 SEG9 74
C317 CDM-OPEN
I-TU-DO 5 Q301 RESET SWITCH 1.2 SEG8
2SC3052F-T1-LF C305 220p
TP309 I/O-I2C-DATA 0 10 8 NC SEG8 73
Q305
O-FUNC-DATA 6 0.2 LED DRIVE 2SC3052F-T1-LF 50V I-RMC 3 1.2 SEG7
TP310 I/O-I2C-CLK 0.7 9 I-RMC SEG7 72
O-FUNC-CLK 7 0.8 1.2 SEG6
TP301 O-POWER 10 NC SEG6 71
Q304 R376
31
O-POWER 8 R384 D302 1.2 SEG5
TP302 O-SP-RELAY R328 C301 C302 R330 2SC3052F-T1-LF C303 1.2k 11 NC SEG5 70
10k 0.1 100 680 10 33k MA2J1110GLS0
D
O-SP-RELY 9 10V 50V C319 X301 1.2 SEG4
TP311 18p 12 NC SEG4 69
D-GND 10 32.768kHz 1 1.2 SEG3
TP312 13 XOA SEG3 68
D
R431
CD/USB-L
CD-A-GND
11
12
TP313 22k
Q304, 305
R497
470
C320
22p
R396
1.5
3.2
14 X1A IC301 SEG2 67
1.2 SEG2
TP314 VOLTAGE DETECT 330k 15 VCC SYSTEM CONTROLLER VSS 66

MAIN CD/USB-R
D400
13 1N4002-A2 5 3.2
BOARD IC301
IC302
TP315 3.1 16 VSS VCC 65
CN607 R498 VCC R321 100 MB90F831PF-G-SPE1
9V 14 O-CD-CE 0 1.2 SEG1
TP316 1k 3 1 17 O-CD-CE SEG1 64
OUT
(Page CD-M-GND 15 REMOTE CONTROL O-CD-CL R320 100 3.1 1.2 SEG0
TP317 2 RECEIVER 18 O-CD-CL SEG0 63
CD-AVR 16 C497 GND I-CD-DI R319 100 3.2 1.2 COM3
23) TP318 I-P-MONI 0.1 3
4
IC302
PNA4823M02S0 100
19 I-CD-DI CMO3 62
E
I-P-MONI 17 O-CD-DO R318 3.1 1.2 COM2
TP319 O-5V-ON 20 O-CD-DO CMO2 61
O-5V-ON 18 1.2 COM1
TP320 21 NC COM1 60
VSTBY 19 1.2 COM0
I-5V/9V-DET R490 R496 R495 R312 22 NC COM0 59
10k 10k 10k 100
VBUSGND 20 O-CD-M-MUTE 0 2.6
R429 O-LED-LCD 23 O-CD-M-MUTE VLCD 58
VBUSGND 21 100k O-CD-RST 3.1 0 R305 100 O-TU-CLK
R430 I-RMC 24 O-CD-RST NC O-TU-CLK 57
100k R491 R492 R493 R304 100
VBUSGND 22 4.7k 68k R315 0 O-TU-DI
I-KEY-WAKE-UP/VOL 1k 25 NC O-LED-LCD O-TU-DI 56
100
VBUS5V 23 O-CD-ON 0 0 R303 100 O-TU-CE
26 O-CD-ON I-USB-TXD O-TU-CE 55
VBUS5V 24 R494 3.2 R337 220 I-RST
33k R499
100 27 O-TP-REC-MUTE I-RST 54
F
VBUS5V 25 O-LED-LCD 3.2 3.2 MD0
I-KEY-WAKE-UP/VOL
28 MD0 53
O-I2C-FUNC-DATA
I-USB-TXD R311 100 2.9 3.2
O-I2C-FUNC-CLK
29 MD1 52
O-USB-SLEEP
1 3 O-TP-REC-MUTE 0 0 MD2
O-USB-RXD
I-5V/9V-DET
CN451
O-USB-RST
30 51
I-TU-ANSD
MD2
25P
I-P-MONI
I-MODEL
I-SUFFIX
R302
I-TU-DO
S491 C340 R400
I-HOLD
I-KEY1
I-KEY2
TP322 100
AVCC
AVSS
0.1 1k
GND
VBUS5V 25 Q451, 452 ROTARY
NC
NC
+3.3V REGULATOR ENCODER
VBUS5V 24
SW491 2 VOLUME 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
VBUS5V 23 C450 R454 R455 R456
TP321
470p 68 68 68
O-CD-ON /
2.5
3.2
3.1
3.1
1.5
3.2
3.2
3.2
2.1
2.9
3.1
3.2
2.6
3.3
3.2
3.2
VBUSGND 22
G
VBUSGND 21
VBUSGND 20
TP326 R449 0 O-USB-RST
USB-RST 19
TP327 R458 0 O-USB-RXD
USB-RXD Q451
18 KTC3203Y-AT R391
TP328 R459 0 I-USB-TXD 7.7
USB-TXD 47k (E2)
17 5.6k (E4)
TP329 R460 0 O-USB-SLEEP 4
USB-SLEEP 100k (E51, MX, AR) R401
16
B CD-CE 15
TP330
TP331
R461
R462
0
0
O-CD-CE
O-CD-CL 3.3
R451
100
R453
1k
R452
22k
1k
USB CD-CL 14
TP332 R463 0 O-CD-DO
BOARD
H
CD-DI 13
CN901 TP333 R464 0 I-CD-DI
Q452
(Page CD-DO
CD-RST
12
11
TP334 R465 0 O-CD-RST 4 2SC3052F-T1-LF R392
10k
C330
0.1
R390
10k
R402
100k
21) CD-M-MUTE 10
TP335 R466 0 O-CD-M-MUTE 0
TP336 R378
100
100
100
100
27k
DVDD3.3V 9 4.7k
C451
DGND 8 220
R382
R309
R419
R306
R434
10V R379
AGND 4.7k
7 D304 R377 R308 R307 R383
C452 C453 R450 R373 D451 MA2J1110GLS0 100 100 100 100
CD/USB-Lch 6 MAZ8039GHLS0
470 2200p 10k 10k
I-KEY-WAKE-UP/VOL
10V
I
AU-GND 5
CD/USB-Rch 4
O-USB-SLEEP
I/O-I2C-DATA
D453 D452
O-USB-RXD
I-5V/9V-DET
O-USB-RST
I/O-I2C-CLK
I-TU-ANSD
AVDD3.3V 3 1N4002-A2 1N4002-A2
I-P-MONI
TP337
I-TU-DO
I-HOLD
I-KEY1
I-KEY2
CD-VM7V 2
TP338 I-KEY1
CD-M-GND 1 C454
470
I-KEY2
10V
R471 R481
R476 R475 R474 R473 R472 1k 1k
3.9k 2.7k 2.2k 1.5k 1.2k
J R470
10k C332 R420 C336 C338
0.01 100k 0.1 1000p
SW475
SW476 SW474 SW473 SW472 SW471
- TUNING
DSGX - REC TO FUNCTION
USB CN305
11P
I-RST TP371
1 RST
MD0 TP372
R487 R486 R485 R484 R483 R482 R480
2 MD0
6.8k 3.9k 2.7k 2.2k 1.5k 1.2k 10k LCD301 MD2 TP373
K LIQUID CRYSTAL DISPLAY

TP374
3
4
MD2
GND
TP375
5 VDD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 I-HOLD TP376
SW486
SW481 SW482 SW483 SW484 SW487 SW485 6 P66(42) (NC)
I-KEY-WAKE-UP/VOL TP377
TUNING + 7 P65(41)
CD USB ENTER + OPTIONS O-USB-RXD TP378
8 RXD(31)
SEG10
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG11
COM0
COM1
COM2
COM3
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
I-USB-TXD TP379
9 TXD(29)
TP380
L O-TP-REC-MUTE
10 SCLK(30)
11
HCD-EC59
27 27
HCD-EC59
5-11. PRINTED WIRING BOARD - PT-SWITCH Board - • See page 15 for Circuit Boards Location. • : Uses unleaded solder.
1 2 3 4 5 6 7
(AC IN)
PT-SWITCH BOARD (MX) (EXCEPT MX)

RY051 RY052
C051
JW009
JW008
JW019 JW020
B (MX) (EXCEPT MX)
JW018 (E2, E4, E51)
JW016 JW011
CN051
JW017 JW012 -2
3 1
PT054 JW003
MAIN POWER
C TRANSFORMER
1
(AR)
S051
JW013
VOLTAGE
JW004 SELECTOR
JW015
14 230 – 240V
W052 PT051 (MX) 220V

8 SUB POWER
1 TRANSFORMER 4 120V
D JW006
E
MAIN BOARD JW014 -1
CN604 JW007
(Page 22)
1
10 6 (MX)
D053 D051 11
D052 NOT REPLACEABLE: 1-882-027- (11)
E BUILT IN TRANSFORMER
9 5
HCD-EC59
28 28
HCD-EC59
5-12. SCHEMATIC DIAGRAM - PT-SWITCH Board -
1 2 3 4 5 6 7 8
PT-SWITCH BOARD
A
(EXCEPT MX)
(MX) C051
RY051 RY052 0.1
PT051
JW008 JW009
B SUB POWER
TRANSFORMER
MC2836-T112-1
MC2838-T112-1
MC2838-T112-1
JW007 JW004 4 6
D051
D052
D053
3 7
(E2, E4, E51)
C
2 8
VOLTAGE
SELECTOR S051
JW006
1 9
120V -1 CN051
3P
220V
1 LIVE
-2 (AC IN)
3 NEUTRAL
230-240V
JW011
W052
D 8P
JW003 1 RELAY ON/OFF

PT054
MAIN POWER 2 V STBY
TRANSFORMER
(AR)
6 10
3
4
AC DETECT
VH(AC)
E
5
MAIN
VL(AC)
BOARD
5 11 6 GND CN604
7 VL(AC) (Page 23)
E 4 12 8 VH(AC)
3 13
2 14
NOT REPLACEABLE:
F 1
BUILT IN TRANSFORMER
HCD-EC59
29 29
HCD-EC59
• IC Block Diagrams
– BD74UR Board – – MAIN Board –

IC101 LC786950T-US-H IC301 BA5826HFP-E2 IC601 BD3491FS-SE2
PCMLRSY
PCMDATA
PCMREQ
PCMBCK
DVDD15
CONT4
LRVDD
LRREF
LRVSS
RCHO B1 1 32 SDA
DOUT
DVDD
DVDD
LCHO
XVDD
XOUT
SLCO
DVSS
XVSS
VO1(–) 1 28 GND
XIN
D.BUFF B2 2 31 SCL
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 27 VO4(–) C1 3
VO1(+) 2 C2 4
D.BUFF
D.BUFF LEVEL
26 VO4(+) D1 5 INPUT
LPF SHIFT 30 FIL
EFMIN 1 CLOCK 60 C2F (LRSY) D2 6 SELECTOR INPUT
GENERATOR IN1 3 D.BUFF GAIN 29 GND
LEVEL E1 7
MP3/PCM OUTPUT CONTROL SHIFT
RFOUT 2 59 FSEQ (DATACK) E2 8
F1 9
25 IN4 I2C BUS 28 SDA
LPF 3 AUDIO OUTPUT 58 DEFECT (DATA) RESET 4 F2 10
LOGIC 27 SCL
SLICE CONTROL
LEVEL 8FS DIGITAL FILTER/
PHLPF 4 57 TEST1 SEL2 11
CONTROL 1BIT DAC 24 IN4' BUFFER
THERMAL SEL1 12
SHUT-DOWN 26 VCC
AIN 5 STREAM CONTROL/AUDIO INPUT 56 AD_DATA (STDATA)
REGULATOR
VOL1 13
BIAS TRAP VOLUME
CIN 6 RF 55 AD_BCK (STCK) VOL2 14
25 OUT1
SIGNAL
PROCESSOR SURROUND
BIN 7 54 AD_LRCK (STREQ) TC2 15
REGULATOR
TC1 16 TREBLE/
AUDIO CONTROL
DIN 8 53 TEST0 BASS
MUTE/DE-EMPHASIS/ MP3, WMA, AAC
MONITOR ATTENUATION CONTROL/ DECODER 24 SB1
SLCISET 9 BASS/TREBLE/ 52 CONT0 23 BIAS
REGB 5 23 SR
HFC FILTER MP3
VREF 22 SB2
RFMON 10 ENCODER 51 CONT1 REGOUT 6 VCC 22 VCC
21 OUT2
MEMORY 21 VCC
VREF 11 50 CONT2 MUTE 7 MUTE VCC
TES, HFL, MEMORY I/F 1M BIT 20 BCB1
DEFECT 20 IN3' 19 BCA1
JITTC 12 SRC 49 INTB1 GND 8 18 BCA2
INTERPOLATION MUTE 17 BCB2
EIN 13 48 INTB0 IN2' 9
JITTER
ROM 19 IN3
FIN 14 ERROR CORRECTION 47 RESB
DECODER IN2 10
LEVEL
PCNCNT 15 46 DO LEVEL SHIFT D.BUFF
APC MCU D.BUFF SHIFT
SYNCHRONIZATION TEXT
I/F VO2(+) 11 18 VO3(+)
TE 16 DETECTION DECODER 45 DI
EFM D.BUFF
D.BUFF
D/A DEMODULATION VO2(–) 12 17 VO3(–)
TEIN 17 44 CL
SUBCODE GND 13
16 RESETt
LDD 18 DECODER 43 CE
SERVO OPOUT 14
A/D 15 OPIN
CONTROL
LDS 19 42 DVSS
DOUT CONTROL
AVSS 20 PLL3 41 DVDD
CD PLL
PORT CONTROL
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
PCKIST
AVDD
FDO
TDO
SLDO
SPDO
VVSS1
PDOUT1
PDOUT0
VVDD1
CONT5 (M-MUTE)
LIMIT-SW (CONT3)
STREQ (DEFECT)
STCK (FSEQ)
STDATA (C2F)
DVDD
DVSS
DVDD15
VVDD3
VVSS3
HCD-EC59
30 30
HCD-EC59
IC701 NJM2368V (TE2)

REF
CS
CT
V+
8 7 6 5
VOLTAGE
REFERENCE
30 PA
L. O
OSC +
UNDERVOLTAGE
LOCKOUT
S. C. P
+

PWM
ERROR +
AMP
+
+
+
1 2 3 4
OUT
IN-
F. B
GND
IC801 LV23401V-TLM-H
VREF3 (4.3V)
VREF2 (3.3V)
FLL CAP
FM ANT
SD ADJ
ST ADJ
CLK IN
GND4
GND3
DO
CE
CL
L2
L1
DI
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
FLL OSC CAP REFERENCE

OSC
LNA
GND
LOCAL POWER STATE
DIVIDER LDO
OSCILLATOR MANAGEMENT MACHINE
TUNING
AGC DET
SYSTEM
LNA SD OUT ST OUT
BAND-PASS STEREO STEREO AUDIO

DEMODULATOR DE-EMPHASIS
FILTER DECODER BLEND AMPLIFIER
IMAGE DET
ANT CAP
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
AM REF
AM VT
VREF1 (4.3V)
MPX OUT
GND1
L-OUT
R-OUT
VCC LOW
AM LCF
SD OUT
VCC
ST OUT
AM ANT
GND AM
AM AGC
31
HCD-EC59
SECTION 6
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so • Color Indication of Appearance Parts Ex-
The components identified by mark 0
they may have some difference from the ample:
or dotted line with mark 0 are critical for
original one. KNOB, BALANCE (WHITE) . . . (RED)
safety.
• Items marked “*” are not stocked since ↑ ↑
Replace only with part number specified.
they are seldom required for routine ser- Parts Color Cabinet’s Color
vice. Some delay should be anticipated • Abbreviation
when ordering these items. AR : Argentina model
• The mechanical parts with no reference E2 : 120V AC area in E model
number in the exploded views are not sup- E4 : African model
plied. E51 : Chilean and Peruvian models
MX : Mexican model
6-1. OVERALL SECTION
top panel section
#1
2
#1
3
#3
#1
#3 #1
chassis section
front panel section
#2
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 3-363-099-32 SCREW (CASE 3 TP2) #2 7-685-872-01 SCREW +BVTT 3X8 (S)
2 4-120-682-12 PANEL (L), SIDE
3 4-120-683-12 PANEL (R), SIDE #3 7-685-247-14 SCREW +KTP 3X10 TYPE2 NON-SLIT
#1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
32
HCD-EC59
6-2. FRONT PANEL SECTION
not supplied
58 (JACK HOLD board)
not supplied
(JACK board)
59
59
59
57 60 61
not
56 supplied
62
59
59 not
supplied
(USB board)
not supplied
55 (PANEL board)
63
54 59
not supplied
53 not supplied
(USB-JACK board)
#1
52 51
51 4-225-252-01 CUSHION (FOOT) 58 1-832-814-21 CABLE, FLEXIBLE FLAT (9 CORE)
52 4-183-509-01 PLATE, ORNAMENTAL 59 3-087-053-01 +BVTP2.6 (3CR)
53 4-120-663-01 KNOB (VOL) 60 4-159-924-01 SHEET (RM)
54 4-120-658-21 RING (VOL)
55 4-120-657-11 RING, ORNAMENT 61 1-832-635-21 CABLE, FLEXIBLE FLAT (25 CORE)
62 1-838-369-21 CABLE, FLEXIBLE FLAT (25 CORE)
56 4-124-519-61 WINDOW 63 1-838-370-21 CABLE, FLEXIBLE FLAT (25 CORE)
57 A-1772-394-A FRONT PANEL ASSY #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
33
HCD-EC59
6-3. CHASSIS SECTION
106
105
#1 B
#1
#1
D M601
#1
A
not supplied
(REG board) not supplied
102 107
C
#1
#1 not supplied
(AC HOLD board)
not supplied
108
PT054
#1
104
#1
B not
not supplied supplied
(2CH AMP board) D
102
103
A
C
not supplied
(PT-SWITCH board)
102
not supplied
not supplied
(CORD HOLD board)
101
101 4-225-252-01 CUSHION (FOOT) 0 107 1-834-966-41 POWER-SUPPLY CORD (E2, E4, E51)
102 3-077-331-01 +BV3 (3-CR) 0 107 1-837-312-11 CORD, POWER-SUPPLY (AR)
103 1-832-796-21 CABLE, FLEXIBLE FLAT (5 CORE) 0 107 1-837-344-11 CORD, POWER-SUPPLY (MX)
104 3-905-609-31 SCREW (TRANSISTOR) 108 4-900-386-01 SCREW +BV SUMITITE S 4X8 ROUND
105 A-1772-508-A MAIN BOARD, COMPLETE (E2, E51, AR) 0 M601 1-787-344-11 FAN, DC
105 A-1772-509-A MAIN BOARD, COMPLETE (MX) 0 PT054 1-445-881-11 TRANSFORMER, POWER (MX)
105 A-1787-869-A MAIN BOARD, COMPLETE (E4) 0 PT054 1-445-882-11 TRANSFORMER, POWER (E2, E4, E51, AR)
106 4-183-684-01 PANEL, BACK (E2, E51) #1 7-685-647-79 SCREW +BVTP 3X10 TYPE2 IT-3
106 4-183-684-11 PANEL, BACK (MX, AR)
106 4-183-684-21 PANEL, BACK (E4)
34
HCD-EC59
6-4. TOP PANEL SECTION
166
165
not supplied
164
163 162
161
160
SW305
159
158
155 157
156 (including sled motor (M402), spindle motor (M401))
155
154
153 153
not supplied 154
(spindle motor (M401)) not supplied not supplied
not supplied (sled motor (M402))
153
152
S001
151
151 A-1748-699-A BD74UR BOARD, COMPLETE 161 3-047-468-11 DAMPER
152 1-834-268-21 WIRE (FLAT TYPE) (16 CORE) 162 4-145-341-01 SPRING (LID)
153 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING 163 4-161-552-01 PULLEY, CHUCKING (D1)
154 4-189-053-01 INSULATOR (BLUE) 164 1-452-899-31 MAGNET
155 4-189-053-11 INSULATOR (GRAY) 165 3-253-143-01 SCREW (B2.6), (+) P TAPPING
156 3-080-204-31 SCREW, TAPPING, P2 166 4-120-740-02 LID (CD)

0 157 A-1780-028-A OPTICAL PICK-UP BLOCK (DA11MMVGP) S001 1-771-853-11 SWITCH, DETECTION (LIMIT)
(Including sled motor (M402), spindle motor (M401)) SW305 1-692-960-11 SWITCH, PUSH (1 KEY)
158 4-166-010-01 COVER (D1) (CD LID OPEN/CLOSE DETECT)
159 4-120-739-12 PANEL, TOP
160 3-087-053-01 +BVTP2.6 (3CR)
35
HCD-EC59
SECTION 7
2CH AMP BD74UR
ELECTRICAL PARTS LIST
Note:
• Due to standardization, replacements in • CAPACITORS
When indicating parts by reference num-
the parts list may be different from the uF: μF
ber, please include the board name.
parts specified in the diagrams or the com- • COILS
ponents used on the set. uH: μH
• -XX and -X mean standardized parts, so • SEMICONDUCTORS The components identified by mark 0
they may have some difference from the In each case, u: μ, for example: or dotted line with mark 0 are critical for
original one. uA. . : μA. . , uPA. . , μPA. . , safety.
• Items marked “*” are not stocked since uPB. . : μPB. . , uPC. . , μPC. . , Replace only with part number specified.
they are seldom required for routine ser- uPD. . : μPD. .
vice. Some delay should be anticipated • Abbreviation
when ordering these items. AR : Argentina model
• RESISTORS E2 : 120V AC area in E model
All resistors are in ohms. E4 : African model
METAL: Metal-film resistor. E51 : Chilean and Peruvian models
METAL OXIDE: Metal oxide-film resistor. MX : Mexican model
F: nonflammable
2CH AMP BOARD
************** R108 1-216-841-11 METAL CHIP 47K 5% 1/10W
R109 1-216-817-11 METAL CHIP 470 5% 1/10W
< CAPACITOR > R110 1-216-817-11 METAL CHIP 470 5% 1/10W
0 R111 1-216-361-31 METAL OXIDE 0.22 5% 2W F
C101 1-126-960-11 ELECT 1uF 20% 50V 0 R112 1-216-361-31 METAL OXIDE 0.22 5% 2W F
C102 1-126-960-11 ELECT 1uF 20% 50V
C103 1-164-315-11 CERAMIC CHIP 470PF 5% 50V R113 1-216-841-11 METAL CHIP 47K 5% 1/10W
C104 1-164-315-11 CERAMIC CHIP 470PF 5% 50V R114 1-216-841-11 METAL CHIP 47K 5% 1/10W
C105 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R115 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R116 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
C106 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R119 1-216-809-11 METAL CHIP 100 5% 1/10W
C107 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V
C108 1-162-908-11 CERAMIC CHIP 3PF 0.25PF 50V R120 1-216-821-11 METAL CHIP 1K 5% 1/10W
C109 1-126-947-11 ELECT 47uF 20% 35V R141 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
C110 1-126-947-11 ELECT 47uF 20% 35V R142 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R143 1-216-837-11 METAL CHIP 22K 5% 1/10W
C111 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V R144 1-216-837-11 METAL CHIP 22K 5% 1/10W
C112 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C141 1-164-156-11 CERAMIC CHIP 0.1uF 25V R145 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
C160 1-165-621-11 CERAMIC CHIP 0.1uF 50V R160 1-216-813-11 METAL CHIP 220 5% 1/10W
R161 1-216-813-11 METAL CHIP 220 5% 1/10W
C162 1-126-968-11 ELECT 100uF 20% 50V
C163 1-126-968-11 ELECT 100uF 20% 50V R163 1-216-813-11 METAL CHIP 220 5% 1/10W
C164 1-165-621-11 CERAMIC CHIP 0.1uF 50V *************************************************************
A-1748-699-A BD74UR BOARD, COMPLETE
< CONNECTOR > ***********************
CN100 1-784-766-11 CONNECTOR, FFC 5P < CAPACITOR >
< DIODE > C101 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C102 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
D140 6-501-817-01 DIODE MA2J1110GLS0 C103 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
D141 6-500-335-01 DIODE MC2838-T112-1 C104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< IC >
IC102 6-705-625-01 IC STK433-040 C107 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< TRANSISTOR > C110 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
Q141 6-551-270-01 TRANSISTOR 2SA2026
Q142 6-551-270-01 TRANSISTOR 2SA2026 C112 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
< RESISTOR > C116 1-128-995-21 ELECT CHIP 100uF 20% 10V
R103 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C118 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R104 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R105 1-216-825-11 METAL CHIP 2.2K 5% 1/10W C119 1-128-995-21 ELECT CHIP 100uF 20% 10V
R107 1-216-841-11 METAL CHIP 47K 5% 1/10W C121 1-164-156-11 CERAMIC CHIP 0.1uF 25V
36
HCD-EC59
BD74UR JACK
R120 1-216-833-11 METAL CHIP 10K 5% 1/10W
C124 1-128-995-21 ELECT CHIP 100uF 20% 10V R121 1-216-833-11 METAL CHIP 10K 5% 1/10W
C125 1-164-156-11 CERAMIC CHIP 0.1uF 25V R122 1-216-833-11 METAL CHIP 10K 5% 1/10W
R126 1-216-864-11 SHORT CHIP 0
C129 1-128-995-21 ELECT CHIP 100uF 20% 10V R129 1-216-809-11 METAL CHIP 100 5% 1/10W
C130 1-164-156-11 CERAMIC CHIP 0.1uF 25V R131 1-216-295-00 SHORT CHIP 0
C133 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R202 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R203 1-216-864-11 SHORT CHIP 0
C203 1-137-710-91 CERAMIC CHIP 10uF 20% 6.3V R302 1-216-839-11 METAL CHIP 33K 5% 1/10W
C205 1-137-710-91 CERAMIC CHIP 10uF 20% 6.3V R303 1-216-834-11 METAL CHIP 12K 5% 1/10W
C206 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C207 1-128-995-21 ELECT CHIP 100uF 20% 10V R304 1-216-833-11 METAL CHIP 10K 5% 1/10W
R305 1-216-832-11 METAL CHIP 8.2K 5% 1/10W
C208 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V R401 1-216-295-00 SHORT CHIP 0
C209 1-164-156-11 CERAMIC CHIP 0.1uF 25V R402 1-216-295-00 SHORT CHIP 0
R405 1-216-809-11 METAL CHIP 100 5% 1/10W
R411 1-216-809-11 METAL CHIP 100 5% 1/10W
C413 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V R414 1-216-809-11 METAL CHIP 100 5% 1/10W
R416 1-216-809-11 METAL CHIP 100 5% 1/10W
< CONNECTOR > R417 1-216-295-00 SHORT CHIP 0
CN201 1-770-425-51 CONNECTOR, FFC/FPC 16P < VIBRATOR >

CN403 1-784-875-51 CONNECTOR, FFC (LIF (NON-ZIF)) 25P
X101 1-795-101-21 VIBRATOR, CERAMIC (16.934MHz)
< IC > *************************************************************
IC101 6-713-623-01 IC LC786950T-US-H JACK BOARD

IC301 6-710-637-01 IC BA5826HFP-E2 ***********
< TRANSISTOR > < CAPACITOR >
Q201 6-551-120-01 TRANSISTOR 2SA2119K C491 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< RESISTOR > C496 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R101 1-216-815-11 METAL CHIP 330 5% 1/10W < CONNECTOR >

R102 1-216-833-11 METAL CHIP 10K 5% 1/10W
R103 1-216-864-11 SHORT CHIP 0 CN496 1-784-770-11 CONNECTOR, FFC 9P
R104 1-216-864-11 SHORT CHIP 0
R105 1-216-864-11 SHORT CHIP 0 < JACK >
R106 1-216-864-11 SHORT CHIP 0 J491 1-566-822-51 JACK (PC IN)

R107 1-216-843-11 METAL CHIP 68K 5% 1/10W J492 1-815-629-11 JACK (PHONES)
R108 1-216-821-11 METAL CHIP 1K 5% 1/10W
R109 1-216-821-11 METAL CHIP 1K 5% 1/10W < RESISTOR >
R111 1-216-837-11 METAL CHIP 22K 5% 1/10W
R477 1-216-837-11 METAL CHIP 22K 5% 1/10W
R112 1-216-864-11 SHORT CHIP 0 R478 1-216-837-11 METAL CHIP 22K 5% 1/10W
R113 1-216-819-11 METAL CHIP 680 5% 1/10W *************************************************************
R114 1-216-819-11 METAL CHIP 680 5% 1/10W
R116 1-216-843-11 METAL CHIP 68K 5% 1/10W
R117 1-216-833-11 METAL CHIP 10K 5% 1/10W
37
HCD-EC59
MAIN
A-1772-508-A MAIN BOARD, COMPLETE (E2, E51, AR) C699 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
A-1772-509-A MAIN BOARD, COMPLETE (MX) C700 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
A-1787-869-A MAIN BOARD, COMPLETE (E4)
********************* C713 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
< CAPACITOR > C731 1-126-963-11 ELECT 4.7uF 20% 50V
C732 1-126-964-11 ELECT 10uF 20% 50V
C607 1-164-156-11 CERAMIC CHIP 0.1uF 25V C760 1-126-941-11 ELECT 470uF 20% 25V
C609 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C761 1-126-935-11 ELECT 470uF 20% 16V
C610 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C762 1-126-916-11 ELECT 1000uF 20% 6.3V
C611 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C763 1-164-315-11 CERAMIC CHIP 470PF 5% 50V
C764 1-126-964-11 ELECT 10uF 20% 50V
C612 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V C765 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C618 1-164-156-11 CERAMIC CHIP 0.1uF 25V C766 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C619 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C771 1-126-960-11 ELECT 1uF 20% 50V
C620 1-104-658-91 ELECT 100uF 20% 10V C773 1-126-933-11 ELECT 100uF 20% 16V
C621 1-136-165-00 FILM 0.1uF 5% 50V C788 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C622 1-126-974-11 ELECT 3300uF 20% 50V
C623 1-136-165-00 FILM 0.1uF 5% 50V C789 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C627 1-126-943-11 ELECT 2200uF 20% 25V C811 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C628 1-126-942-61 ELECT 1000uF 20% 25V C813 1-126-963-11 ELECT 4.7uF 20% 50V
C631 1-126-933-11 ELECT 100uF 20% 16V C815 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C632 1-126-963-11 ELECT 4.7uF 20% 50V C816 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C820 1-126-965-11 ELECT 22uF 20% 50V
C633 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V C821 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
(EXCEPT E4) C854 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C855 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C639 1-162-979-11 CERAMIC CHIP 0.0027uF 10% 50V (E4)
(EXCEPT E4) C859 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C640 1-162-979-11 CERAMIC CHIP 0.0027uF 10% 50V (E4) C860 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C641 1-126-962-11 ELECT 3.3uF 20% 50V C861 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C645 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C863 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C648 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V < CONNECTOR >
C649 1-162-960-11 CERAMIC CHIP 220PF 10% 50V
C650 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V CN601 1-819-131-11 PIN, CONNECTOR 3P
CN603 1-784-766-11 CONNECTOR, FFC 5P
C655 1-162-960-11 CERAMIC CHIP 220PF 10% 50V CN604 1-819-136-11 PIN, CONNECTOR 8P
C656 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V CN605 1-784-770-11 CONNECTOR, FFC 9P
C657 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V CN607 1-784-786-11 CONNECTOR, FFC 25P
C658 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
C661 1-126-964-11 ELECT 10uF 20% 50V CN609 1-815-444-11 PIN, CONNECTOR (PWB) 3P
CN633 1-819-133-11 PIN, CONNECTOR
C662 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V * CN801 1-506-680-11 PLUG, CONNECTOR (2.5mm) 3P
C663 1-126-960-11 ELECT 1uF 20% 50V (ANTENNA FM/AM)
C664 1-126-960-11 ELECT 1uF 20% 50V
C666 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < DIODE >
C667 1-126-934-11 ELECT 220uF 20% 16V
D601 6-500-335-01 DIODE MC2838-T112-1
C674 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V D602 6-500-335-01 DIODE MC2838-T112-1
C684 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V D604 6-501-817-01 DIODE MA2J1110GLS0
C685 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V D605 6-501-817-01 DIODE MA2J1110GLS0
C686 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V D606 6-500-334-01 DIODE MC2836-T112-1
D607 6-502-619-01 DIODE 1N5402-C532-2
C694 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D608 6-502-619-01 DIODE 1N5402-C532-2
C695 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V D609 6-502-619-01 DIODE 1N5402-C532-2
C696 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V D610 6-502-619-01 DIODE 1N5402-C532-2
38
HCD-EC59
MAIN
D611 6-501-582-01 DIODE 1N4002-A2 < RESISTOR >
D612 6-501-582-01 DIODE 1N4002-A2 R609 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D614 6-501-817-01 DIODE MA2J1110GLS0 R610 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
D617 6-500-335-01 DIODE MC2838-T112-1 R611 1-216-797-11 METAL CHIP 10 5% 1/10W
D628 6-501-817-01 DIODE MA2J1110GLS0 R612 1-216-797-11 METAL CHIP 10 5% 1/10W
D631 6-501-817-01 DIODE MA2J1110GLS0 R613 1-216-833-11 METAL CHIP 10K 5% 1/10W
D701 6-502-161-01 DIODE RB055L-40TE25 R614 1-216-833-11 METAL CHIP 10K 5% 1/10W
D731 6-501-722-01 DIODE MAZ8043GMLS0 R615 1-216-797-11 METAL CHIP 10 5% 1/10W
D732 6-501-760-01 DIODE MAZ8100GMLS0 R616 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
D801 6-500-848-01 DIODE MC2840-T112-1 R619 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
D802 6-500-848-01 DIODE MC2840-T112-1 R620 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R621 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
< FERRITE BEAD > R622 1-216-839-11 METAL CHIP 33K 5% 1/10W
R623 1-216-833-11 METAL CHIP 10K 5% 1/10W
FB601 1-412-473-51 INDUCTOR (SMALL TYPE)
R624 1-216-833-11 METAL CHIP 10K 5% 1/10W
< BAND PASS FILTER > R625 1-216-839-11 METAL CHIP 33K 5% 1/10W
R628 1-216-833-11 METAL CHIP 10K 5% 1/10W
FL801 1-236-711-21 FILTER, BAND PASS R637 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R638 1-249-401-11 CARBON 47 5% 1/4W
< IC >
R639 1-216-845-11 METAL CHIP 100K 5% 1/10W
IC601 6-713-384-01 IC BD3491FS-SE2 R640 1-216-845-11 METAL CHIP 100K 5% 1/10W
IC701 6-600-113-01 IC NJM2368V (TE2) R641 1-249-401-11 CARBON 47 5% 1/4W
IC801 6-714-822-01 IC LV23401V-TLM-H R642 1-249-401-11 CARBON 47 5% 1/4W
R643 1-216-833-11 METAL CHIP 10K 5% 1/10W
< JUMPER RESISTOR >
R644 1-216-821-11 METAL CHIP 1K 5% 1/10W
JR601 1-216-864-11 SHORT CHIP 0 R645 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
JR602 1-216-864-11 SHORT CHIP 0 R646 1-216-809-11 METAL CHIP 100 5% 1/10W
JR603 1-216-864-11 SHORT CHIP 0 R647 1-216-797-11 METAL CHIP 10 5% 1/10W
R648 1-216-841-11 METAL CHIP 47K 5% 1/10W
< COIL >
R649 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
L603 1-456-107-11 COIL, AIR-CORE R650 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
L604 1-456-107-11 COIL, AIR-CORE R651 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
L701 1-456-467-31 INDUCTOR 100uH R652 1-216-809-11 METAL CHIP 100 5% 1/10W
L801 1-481-550-21 INDUCTOR 0.039uH R655 1-216-833-11 METAL CHIP 10K 5% 1/10W
L802 1-481-550-21 INDUCTOR 0.039uH
R656 1-216-821-11 METAL CHIP 1K 5% 1/10W
L803 1-457-757-11 COIL, AM ANTENNA R657 1-216-843-11 METAL CHIP 68K 5% 1/10W
0 R658 1-215-890-51 METAL OXIDE 470 5% 2W F
< TRANSISTOR > 0 R662 1-215-890-51 METAL OXIDE 470 5% 2W F
R666 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q604 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q605 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R667 1-216-841-11 METAL CHIP 47K 5% 1/10W
R673 1-216-817-11 METAL CHIP 470 5% 1/10W
Q612 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF
Q618 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF R674 1-249-401-11 CARBON 47 5% 1/4W
Q619 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R675 1-249-401-11 CARBON 47 5% 1/4W
Q706 8-729-040-76 TRANSISTOR KTA1273-Y-AT R676 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q707 8-729-040-76 TRANSISTOR KTA1273-Y-AT R677 1-216-833-11 METAL CHIP 10K 5% 1/10W
R678 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q710 6-551-696-01 TRANSISTOR ISA1235AC1TP-1EF R684 1-216-837-11 METAL CHIP 22K 5% 1/10W
Q731 8-729-037-03 TRANSISTOR KTA1266GR-AT R685 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R687 1-216-837-11 METAL CHIP 22K 5% 1/10W
Q771 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R688 1-216-817-11 METAL CHIP 470 5% 1/10W
R690 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R691 1-216-833-11 METAL CHIP 10K 5% 1/10W
39
HCD-EC59
MAIN PANEL
R692 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R801 1-216-821-11 METAL CHIP 1K 5% 1/10W
R693 1-216-821-11 METAL CHIP 1K 5% 1/10W R802 1-216-821-11 METAL CHIP 1K 5% 1/10W
R697 1-216-864-11 SHORT CHIP 0 R803 1-216-821-11 METAL CHIP 1K 5% 1/10W
R700 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R805 1-216-809-11 METAL CHIP 100 5% 1/10W
R704 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R808 1-216-864-11 SHORT CHIP 0
R706 1-216-813-11 METAL CHIP 220 5% 1/10W R810 1-216-797-11 METAL CHIP 10 5% 1/10W
R707 1-216-813-11 METAL CHIP 220 5% 1/10W R811 1-216-839-11 METAL CHIP 33K 5% 1/10W
R709 1-216-864-11 SHORT CHIP 0 R879 1-216-809-11 METAL CHIP 100 5% 1/10W
R723 1-216-789-11 METAL CHIP 2.2 5% 1/10W R881 1-216-809-11 METAL CHIP 100 5% 1/10W
R727 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R882 1-216-801-11 METAL CHIP 22 5% 1/10W
R728 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
< RELAY >
R731 1-249-395-11 CARBON 15 5% 1/4W
R732 1-249-395-11 CARBON 15 5% 1/4W RY602 1-755-421-11 RELAY
R733 1-249-395-11 CARBON 15 5% 1/4W
R734 1-216-841-11 METAL CHIP 47K 5% 1/10W < TERMINAL >
R735 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
TB602 1-780-314-11 TERMINAL BOARD
R736 1-216-833-11 METAL CHIP 10K 5% 1/10W (SPEAKERS IMPEDANS: USE 6 Ω)
R737 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R738 1-216-817-11 METAL CHIP 470 5% 1/10W < VIBRATOR >
R741 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R742 1-216-789-11 METAL CHIP 2.2 5% 1/10W X801 1-814-067-11 OSCILLATOR, CRYSTAL (32.768kHz)
*************************************************************
R749 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R750 1-216-829-11 METAL CHIP 4.7K 5% 1/10W PANEL BOARD
R751 1-216-830-11 METAL CHIP 5.6K 5% 1/10W ************
R752 1-216-830-11 METAL CHIP 5.6K 5% 1/10W
R753 1-216-830-11 METAL CHIP 5.6K 5% 1/10W 2-649-178-01 PLATE, LIGHT GUIDE
2-649-179-01 SHEET (LCD)
R754 1-216-830-11 METAL CHIP 5.6K 5% 1/10W 2-665-175-01 SHEET (REFLECTOR)
R760 1-216-789-11 METAL CHIP 2.2 5% 1/10W
R761 1-216-817-11 METAL CHIP 470 5% 1/10W < CAPACITOR >
R762 1-216-817-11 METAL CHIP 470 5% 1/10W
C302 1-104-658-91 ELECT 100uF 20% 10V
R764 1-216-827-11 METAL CHIP 3.3K 5% 1/10W C303 1-126-964-11 ELECT 10uF 20% 50V
R765 1-216-827-11 METAL CHIP 3.3K 5% 1/10W C304 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
R767 1-216-791-11 METAL CHIP 3.3 5% 1/10W C305 1-126-964-11 ELECT 10uF 20% 50V
R768 1-216-833-11 METAL CHIP 10K 5% 1/10W
R770 1-216-845-11 METAL CHIP 100K 5% 1/10W C306 1-104-655-91 ELECT 470uF 20% 6.3V
R771 1-216-801-11 METAL CHIP 22 5% 1/10W C319 1-162-918-11 CERAMIC CHIP 18PF 5% 50V
R772 1-216-834-11 METAL CHIP 12K 5% 1/10W C320 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
R774 1-216-833-11 METAL CHIP 10K 5% 1/10W
R781 1-216-845-11 METAL CHIP 100K 5% 1/10W C338 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R787 1-216-835-11 METAL CHIP 15K 5% 1/10W
R791 1-216-845-11 METAL CHIP 100K 5% 1/10W C450 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
R792 1-216-849-11 METAL CHIP 220K 5% 1/10W C451 1-126-923-91 ELECT 220uF 20% 10V
R793 1-216-827-11 METAL CHIP 3.3K 5% 1/10W C452 1-126-925-91 ELECT 470uF 20% 10V
R794 1-216-833-11 METAL CHIP 10K 5% 1/10W
R795 1-216-848-11 METAL CHIP 180K 5% 1/10W C453 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C454 1-126-925-91 ELECT 470uF 20% 10V
R797 1-216-841-11 METAL CHIP 47K 5% 1/10W
R798 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R799 1-216-818-11 METAL CHIP 560 5% 1/10W
40
HCD-EC59
PANEL
< CONNECTOR > R329 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R330 1-216-819-11 METAL CHIP 680 5% 1/10W
CN301 1-784-747-11 CONNECTOR, FFC 25P R331 1-216-845-11 METAL CHIP 100K 5% 1/10W
CN305 1-779-548-21 CONNECTOR, FFC (LIF (NON-ZIF)) 11P R332 1-216-833-11 METAL CHIP 10K 5% 1/10W
CN451 1-779-293-11 CONNECTOR, FFC (LIF (NON-ZIF)) 25P
R333 1-216-845-11 METAL CHIP 100K 5% 1/10W
< DIODE > R334 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R335 1-216-837-11 METAL CHIP 22K 5% 1/10W
D301 6-501-722-01 DIODE MAZ8043GMLS0 R336 1-216-833-11 METAL CHIP 10K 5% 1/10W
D302 6-501-817-01 DIODE MA2J1110GLS0 R337 1-216-813-11 METAL CHIP 220 5% 1/10W
D303 6-500-334-01 DIODE MC2836-T112-1
D306 6-503-056-01 LED 1L0341Y23E0CA602-II (STANDBY) R370 1-216-821-11 METAL CHIP 1K 5% 1/10W
R373 1-216-833-11 METAL CHIP 10K 5% 1/10W
D400 6-501-582-01 DIODE 1N4002-A2 R375 1-216-805-11 METAL CHIP 47 5% 1/10W
D451 6-501-719-01 DIODE MAZ8039GHLS0 R376 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
D452 6-501-582-01 DIODE 1N4002-A2
D453 6-501-582-01 DIODE 1N4002-A2 R377 1-216-809-11 METAL CHIP 100 5% 1/10W
R378 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
< IC > R379 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R381 1-216-821-11 METAL CHIP 1K 5% 1/10W
IC301 A-1786-565-A IC MB90F831PF-G-SPE1 (for SERVICE) R382 1-216-809-11 METAL CHIP 100 5% 1/10W
IC302 6-600-767-01 IC PNA4823M02S0
R383 1-216-809-11 METAL CHIP 100 5% 1/10W
< JUMPER RESISTOR > R384 1-216-839-11 METAL CHIP 33K 5% 1/10W
R390 1-216-833-11 METAL CHIP 10K 5% 1/10W
JR306 1-216-864-11 SHORT CHIP 0 R391 1-216-830-11 METAL CHIP 5.6K 5% 1/10W
JR309 1-216-864-11 SHORT CHIP 0 (E4)
R391 1-216-841-11 METAL CHIP 47K 5% 1/10W
< LIQUID CRYSTAL DISPLAY > (E2)
LCD301 1-811-042-11 DISPLAY PANEL, LIQUID CRYSTAL R391 1-216-845-11 METAL CHIP 100K 5% 1/10W
(E51, MX, AR)
< TRANSISTOR > R392 1-216-833-11 METAL CHIP 10K 5% 1/10W
R396 1-216-851-11 METAL CHIP 330K 5% 1/10W
Q302 8-729-037-13 TRANSISTOR KTA1271Y R401 1-216-821-11 METAL CHIP 1K 5% 1/10W
R420 1-216-845-11 METAL CHIP 100K 5% 1/10W
Q306 8-729-038-28 TRANSISTOR RT1N441C-TP-1 R429 1-216-845-11 METAL CHIP 100K 5% 1/10W
Q451 8-729-036-86 TRANSISTOR KTC3203Y-AT R430 1-216-845-11 METAL CHIP 100K 5% 1/10W
R431 1-216-837-11 METAL CHIP 22K 5% 1/10W
< RESISTOR > R434 1-216-809-11 METAL CHIP 100 5% 1/10W
R449 1-216-864-11 SHORT CHIP 0
R304 1-216-809-11 METAL CHIP 100 5% 1/10W
R454 1-249-403-11 CARBON 68 5% 1/4W
R307 1-216-809-11 METAL CHIP 100 5% 1/10W R455 1-249-403-11 CARBON 68 5% 1/4W
R308 1-216-809-11 METAL CHIP 100 5% 1/10W R456 1-249-403-11 CARBON 68 5% 1/4W
R309 1-216-809-11 METAL CHIP 100 5% 1/10W
R310 1-216-809-11 METAL CHIP 100 5% 1/10W R458 1-216-864-11 SHORT CHIP 0
R460 1-216-864-11 SHORT CHIP 0
R315 1-216-809-11 METAL CHIP 100 5% 1/10W
R465 1-216-864-11 SHORT CHIP 0
R324 1-216-809-11 METAL CHIP 100 5% 1/10W
R327 1-216-809-11 METAL CHIP 100 5% 1/10W R472 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R473 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R328 1-216-833-11 METAL CHIP 10K 5% 1/10W R474 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
41
HCD-EC59
PANEL PT-SWITCH REG USB
R475 1-216-826-11 METAL CHIP 2.7K 5% 1/10W < TRANSFORMER >
R476 1-216-828-11 METAL CHIP 3.9K 5% 1/10W 0 PT051 1-445-105-11 TRANSFORMER, POWER
R480 1-216-833-11 METAL CHIP 10K 5% 1/10W
R481 1-216-821-11 METAL CHIP 1K 5% 1/10W < RELAY >
R482 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R483 1-216-823-11 METAL CHIP 1.5K 5% 1/10W 0 RY051 1-755-276-22 RELAY, POWER (MX)
0 RY052 1-755-496-11 RELAY (EXCEPT MX)
R484 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R485 1-216-826-11 METAL CHIP 2.7K 5% 1/10W < VOLTAGE SELECTOR >
R486 1-216-828-11 METAL CHIP 3.9K 5% 1/10W
R487 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W 0 S051 1-786-408-11
SELECTOR, VOLTAGE (SWS-2301)
R490 1-216-833-11 METAL CHIP 10K 5% 1/10W (VOLTAGE SELECTOR) (E2, E4, E51)
*************************************************************
R491 1-216-821-11 METAL CHIP 1K 5% 1/10W
R492 1-216-829-11 METAL CHIP 4.7K 5% 1/10W REG BOARD
R493 1-216-843-11 METAL CHIP 68K 5% 1/10W **********
R494 1-216-839-11 METAL CHIP 33K 5% 1/10W
R495 1-216-833-11 METAL CHIP 10K 5% 1/10W < CAPACITOR >
R497 1-216-817-11 METAL CHIP 470 5% 1/10W C698 1-164-156-11 CERAMIC CHIP 0.1uF 25V
R498 1-216-821-11 METAL CHIP 1K 5% 1/10W
R499 1-216-809-11 METAL CHIP 100 5% 1/10W < IC >
< ROTARY ENCODER > IC690 6-713-032-01 IC KIA7809API-U/PF

*************************************************************
S491 1-786-417-11 ENCODER, ROTARY (VOLUME)
USB BOARD
< SWITCH > **********
SW471 1-771-410-21 SWITCH, TACTILE (FUNCTION) < CAPACITOR >

SW472 1-771-410-21 SWITCH, TACTILE (REC TO USB)
SW473 1-771-410-21 SWITCH, TACTILE ( –) C900 1-117-681-11 ELECT CHIP 100uF 20% 16V
SW474 1-771-410-21 SWITCH, TACTILE (u) C901 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
SW475 1-771-410-21 SWITCH, TACTILE (– TUNING l m) C902 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
SW476 1-771-410-21 SWITCH, TACTILE (DSGX) C904 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
SW481 1-771-410-21 SWITCH, TACTILE (CD)
SW482 1-771-410-21 SWITCH, TACTILE (USB) C905 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
SW483 1-771-410-21 SWITCH, TACTILE (ENTER) C906 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
SW484 1-771-410-21 SWITCH, TACTILE ( +) C907 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
SW485 1-771-410-21 SWITCH, TACTILE (x) C909 1-164-156-11 CERAMIC CHIP 0.1uF 25V
SW486 1-771-410-21 SWITCH, TACTILE (TUNING + M L)
SW487 1-771-410-21 SWITCH, TACTILE (OPTIONS) C915 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
SW491 1-771-410-21 SWITCH, TACTILE (I/1) C916 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
< VIBRATOR > C918 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
X301 1-814-067-11 OSCILLATOR, CRYSTAL (32.768kHz)
X302 1-813-548-31 VIBRATOR, CERAMIC (6MHz) C920 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
************************************************************* C921 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
PT-SWITCH BOARD C951 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
*************** C952 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
< CAPACITOR > C953 1-164-156-11 CERAMIC CHIP 0.1uF 25V

C954 1-126-601-11 ELECT CHIP 2.2uF 20% 50V
C051 1-165-621-11 CERAMIC CHIP 0.1uF 50V C955 1-165-884-11 CERAMIC CHIP 2.2uF 10% 6.3V
< CONNECTOR > < CONNECTOR >
0 CN051 1-793-660-11 PIN, CONNECTOR (PC BOARD) 3P CN901 1-784-382-51 CONNECTOR, FFC/FPC 25P
CN902 1-784-382-51 CONNECTOR, FFC/FPC 25P
< DIODE > CN903 1-764-250-11 PIN, CONNECTOR (PC BOARD) 4P
CN910 1-784-366-51 CONNECTOR, FFC/FPC 7P
D051 6-500-334-01 DIODE MC2836-T112-1
D052 6-500-335-01 DIODE MC2838-T112-1 < IC >
D053 6-500-335-01 DIODE MC2838-T112-1
IC901 A-1768-193-A IC LC87F1JJ2AU-SQFP-H (for SERVICE)
42
HCD-EC59
USB USB-JACK
< RESISTOR > MISCELLANEOUS
**************
R900 1-216-864-11 SHORT CHIP 0
R901 1-216-809-11 METAL CHIP 100 5% 1/10W 58 1-832-814-21 CABLE, FLEXIBLE FLAT (9 CORE)
R902 1-216-809-11 METAL CHIP 100 5% 1/10W 61 1-832-635-21 CABLE, FLEXIBLE FLAT (25 CORE)
R903 1-216-857-11 METAL CHIP 1M 5% 1/10W 62 1-838-369-21 CABLE, FLEXIBLE FLAT (25 CORE)
R904 1-216-864-11 SHORT CHIP 0 63 1-838-370-21 CABLE, FLEXIBLE FLAT (25 CORE)
103 1-832-796-21 CABLE, FLEXIBLE FLAT (5 CORE)
R905 1-216-809-11 METAL CHIP 100 5% 1/10W
R906 1-216-809-11 METAL CHIP 100 5% 1/10W 0 107 1-834-966-41 POWER-SUPPLY CORD (E2, E4, E51)
R907 1-216-809-11 METAL CHIP 100 5% 1/10W 0 107 1-837-312-11 CORD, POWER-SUPPLY (AR)
R908 1-216-809-11 METAL CHIP 100 5% 1/10W 0 107 1-837-344-11 CORD, POWER-SUPPLY (MX)
R909 1-216-809-11 METAL CHIP 100 5% 1/10W 152 1-834-268-21 WIRE (FLAT TYPE) (16 CORE)
0 157 A-1780-028-A OPTICAL PICK-UP BLOCK (DA11MMVGP)
R910 1-216-845-11 METAL CHIP 100K 5% 1/10W (Including sled motor (M402), spindle motor (M401))
R911 1-216-809-11 METAL CHIP 100 5% 1/10W
R912 1-216-845-11 METAL CHIP 100K 5% 1/10W 164 1-452-899-31 MAGNET
R913 1-216-809-11 METAL CHIP 100 5% 1/10W 0 M601 1-787-344-11 FAN, DC
R914 1-216-845-11 METAL CHIP 100K 5% 1/10W 0 PT054 1-445-881-11 TRANSFORMER, POWER (MX)
0 PT054 1-445-882-11 TRANSFORMER, POWER (E2, E4, E51, AR)
R915 1-216-809-11 METAL CHIP 100 5% 1/10W S001 1-771-853-11 SWITCH, DETECTION (LIMIT)
R916 1-216-809-11 METAL CHIP 100 5% 1/10W
R917 1-216-809-11 METAL CHIP 100 5% 1/10W SW305 1-692-960-11
SWITCH, PUSH (1 KEY)
R918 1-216-805-11 METAL CHIP 47 5% 1/10W (CD LID OPEN/CLOSE DETECT)
R919 1-216-805-11 METAL CHIP 47 5% 1/10W *************************************************************
R920 1-216-805-11 METAL CHIP 47 5% 1/10W ACCESSORY

R921 1-216-809-11 METAL CHIP 100 5% 1/10W ***********
R922 1-216-809-11 METAL CHIP 100 5% 1/10W
R923 1-216-809-11 METAL CHIP 100 5% 1/10W 0 1-569-008-33 ADAPTOR, CONVERSION (E2, E4, E51)
R924 1-216-809-11 METAL CHIP 100 5% 1/10W
R951 1-216-835-11 METAL CHIP 15K 5% 1/10W

R952 1-216-835-11 METAL CHIP 15K 5% 1/10W
R953 1-216-803-11 METAL CHIP 33 5% 1/10W
R954 1-216-803-11 METAL CHIP 33 5% 1/10W
R955 1-216-864-11 SHORT CHIP 0
< VIBRATOR >
X901 1-814-365-11 QUARTZ CRYSTAL UNITS (12MHz)

*************************************************************
USB-JACK BOARD
***************
< CAPACITOR >
C561 1-126-923-91 ELECT 220uF 20% 10V

C565 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< CONNECTOR >
CN560 1-794-548-21 CONNECTOR, USB (A) ( )
< JUMPER RESISTOR >
FB561 1-216-295-00 SHORT CHIP 0

FB562 1-216-295-00 SHORT CHIP 0
< RESISTOR >
R561 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R562 1-216-789-11 METAL CHIP 2.2 5% 1/10W
*************************************************************
43
HCD-EC59
REVISION HISTORY
Checking the version allows you to jump to the revised page.

Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision
1.0 2010.06 New

Sony Hcd Ec59

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Sony Hcd Ec59

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony Hcd Ec59

Uploaded by

Copyright:

Available Formats

HCD-EC59

SERVICE MANUAL E Model

• HCD-EC59 is the amplifier, USB, CD player and

COMPACT DISC RECEIVER

9-889-885-01 Sony Corporation

NOTES ON CHIP COMPONENT REPLACEMENT TABLE OF CONTENTS

7. ELECTRICAL PARTS LIST .............................. 36

Accessories are given in the last of the electrical parts list.

SAFETY-RELATED COMPONENT WARNING!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

NOTES ON LASER DIODE EMISSION CHECK

: LEAD FREE MARK LASER DIODE AND FOCUS SEARCH OPERATION

Fig. 1. Method to push the SW305

CAPACITOR ELECTRICAL DISCHARGE PROCESSING

• MAIN board (C622, C626)

– MAIN Board (Conductor Side) –

C626 800 :/2 W

MAIN BOARD SERVICE POSITION

• SIDE PANEL (L) was removed.

– Rear side view –

PT-SWITCH BOARD SERVICE POSITION

• SIDE PANEL (R) was removed.

BD74UR BOARD SERVICE POSITION

top panel block

2-1. DISASSEMBLY FLOW

2-2. SIDE PANEL (L)/(R)

2-3. TOP PANEL ASSY

2-5. KNOB (VOL)

Note: Follow the disassembly procedure in the numerical order given.

2-2. SIDE PANEL (L)/(R)

5 side panel (L) 2 two screws

2-3. TOP PANEL ASSY

7 top panel assy

4 flexible flat cable (25 core)

2-4. FRONT PANEL BLOCK

3 screw (BVTP3 u 10)

1 flexible flat cable (25 core)

2 flexible flat cable (9 core)

2-5. KNOB (VOL)

front panel block

1 flexible flat cable (25 core)

2 Push the knob (VOL) by flat-head screwdriver.

2-6. MAIN BOARD

5 flexible flat cable (5 core)

7 fan motor connector

1 flexible flat cable (25 core)

2-7. BASE UNIT (BU-D1BD74UR)

1 four floating screws

2-8. OPTICAL PICK-UP BLOCK (DA11MMVGP)

5 tapping screw (P2)

7 optical pick-up block

2 Solder the short-land.

3 wire (flat type) (16 core) (optical pick-up)

4 BD74UR board block

1 Remove four solders.

PANEL TEST MODE CD SERVICE MODE

FCSAG ** (**: Focus AGC value)

TRKAG ** (**: Track AGC value)

FCSAG (: Focus AGC value)

TRKAG (: Track AGC value)

RF_AG (: RF AGC value)