User manual for Bluetooth module (Model: MY-DJAP-BD)

Features description

z Use Bluetooth 2.1 + EDR specifications based on CLASS 2 power level

z Support L2CAP/A2DP (AVCTP / AVDTP / AVRCP to receive stereo audio signal and
control the Prev/Next operation of the audio transmitter by agreement;
z Support Simple Pairing, without the pairing code, support automatic back even
function
Note:
z SBC decode for Bluetooth audio streaming
z Easy to build using simple SMD
z Support Piconet

Note
a. That module is limited to OEM installation ONLY

b. That module is limited to installation in mobile or fixed applications, according to Part 2.1091(b).

c. That separate approval is required for all other operating configurations, including portable configurations
with respect to Part 2.1093 and different antenna configurations.

d. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or
install module.
e. The module is limited to installation in mobile or fixed applications
 Technical Specifications
General Specification
Number Items Description
1 Bluetooth Standard Bluetooth v2.1+EDR
2 Chipset CW6639E
3 Dimension 16.9mm x 14.2mm x 2mm
4 Voltage 3.3V
5 Temperature -20̚+70 䉝
6 Storage Temperature -40̚+85 䉝
7 Frequency Range 2402̚2480MHz
8 Maximum RF Transmit Power 6dBm
9 Receive Sensitivity -80dBm
10 Bluetooth® Profile Supported A2DP,AVRCP,HFP,HSP,APTX

Power Consumption

BMLE45 Item Min Typ Max Unit Note

State Working voltage 3.3 V
Working current 12 mA Call and music
Standby current 86 uA
Power supply˖3.3V

Operational Mode Minimum Typical Maximum

Page scan, time internal 1.28s - 1mA -

Inquiry - 55mA -
Page scan and Inquiry - 1.6mA -
ACL no traffic - 26mA -
ACL with file transfer - 47mA -
SCO HV3 - 52mA -
Sleep - 80uA -
 Stereo Codec: Analogue to Digital Converter

Analogue to Digital Converter

Parameter Conditions Min Typ Max Note
Resolution - - - 16 Bits
Input Sample - 8 - 48 kHz
Rate,FSAMPLE
fin=1kHz FSAMPLE
SNR B/W=20Hz-Fsample/2 8kHz - 93.5 - dB
(20kHz max) 16kHz 92.5 dB
A-Weighted 32kHz 91.4 dB
THD+N<0.1% 44.1kHz 90.4 dB
1.6Vpk-pk input 48kHz 89.6 dB
THD+N fin=1kHz FSAMPLE
B/W=20Hz- Fsample/2 8kHz - 0.0041 - %
(20kHz max) 48kHz - 0.0072 - %
1.6Vpk-pk input
Digital Gain Digital Gain Resolution=1/32dB -24 - 21.5 dB
Analogue Gain Pre-amplifier setting = 0dB, 9dB, 21dB -3 - 42 dB
or30dB
Analogue setting = -3dB to 12dB in
3dB steps
Stereo separation (crosstalk) - -88.5 - dB

Stereo Codec: Digital to Analogue Converter

Analogue to Digital Converter

Parameter Conditions Min Typ Max Note
Resolution - - - 16 Bits
Output Sample - 8 - 96 kHz
Rate,FSAMPLE
fin=1kHz FSAMPLE Load
SNR B/W=20Hz-20kHz 48kHz Nȍ - 95.6 - dB
A-Weighted 48kHz ȍ - 95.8 - dB
THD+N<0.1% 48kHz ȍ - 95.6 - dB
0dBFS input
THD+N fin=1kHz FSAMPLE Load
B/W=20Hz-20kHz 8kHz Nȍ - 0.0025 - %
0dBFS input 8kHz ȍ - 0.0056 - %
8kHz ȍ - 0.0108 %

48kHz Nȍ - 0.0027 %

48kHz ȍ - 0.0067 %

48kHz ȍ - 0.0122 %

Digital Gain Digital Gain Resolution=1/32dB -24 - 21.5 dB

Analogue Gain Analogue Gain Resolution = 3dB -21 - 0 dB
Stereo separation (crosstalk) - -87.5 - dB

Auxiliary ADC
Auxiliary ADC Min Typ Max Unit
Resolution - - 10 Bits
Input voltage range(a) 0 - VDD_AUX V
Accuracy INL -1 - 1 LSB
(Guaranteed monotonic) DNL 0 - 1 LSB
Offset -1 - 1 LSB
Gain error -0.8 - 0.8 %
Input bandwidth - 100 kHz
Conversion time 1.38 1.69 2.75 µs
Sample rate(b) - - 700 Samples/s
(a)LSB size = VDD_AUX/1023
(b)The auxiliary ADC is accessed through a VM function. The sample rate given is achieved as part of this
function.
Auxiliary DAC
Auxiliary DAC Min Typ Max Unit
Resolution - - 10 Bits
Supply voltage, VDD_AUX 1.30 1.35 1.40 V
Output voltage range 0 - VDD_AUX V
Full-scale output voltage 1.30 1.35 1.40
LSB size 0 1.32 - 2.64 mV
Offset -1.32 0 1.32 mV
Integral non-linearity -1 0 1 LSB
Settling time (a) - - 250 ns
(a) The settling time does not i nclude any capacitive load
Block Diagram
Mechanical Dimensions and Electrical
feature

Electrical specific
Pin number Name State
ation
1 TP1 Digital I/O Test PIN
2 TP2 Digital I/O Test PIN
3 TP3 Digital I/O Test PIN
4 VIN Power Power Input
5 GND Power Digital Ground
6 GND Power Digital Ground
7 TXD Digital I/O CMD2026 CW6638 UART Transfer
8 RXD Digital I/O CMD2026 CW6638 UART Receiver
9 CTS Digital I/O APB8202 CW6638 UART Flow Control
10 TP6 Digital I/O Test PIN
11 TP5 Digital I/O Test PIN
12 TP4 Digital I/O Test PIN
Related recommended
Ɣ Module output audio is a differential signal

Ɣ If you want to use the MIC function, in order to achieve the best sound

effects, please don't take MICAnd SPK is placed in the same plane,

preferably vertically placed

Ɣ Full metal shell will greatly shorten the Bluetooth transmission distance

Ɣ Bluetooth antenna below PCB plate not copper

Disclaimer

7+(6( 0$7(5,$/6 $1' ,1)250$7,21$5(3529,'(' ³$6 ,6´ :,7+287 :$55$17<2) ANY KIND,
EITHER EXPRESS OR IMPLIED , INCLUDING BUT NOT LIMITED TO, THEIMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSEOR NON-INFRINGEMENT.

We use reasonable efforts to include accurate and up-to-date information on this document; it does not, however, make
any representations as to its accuracy or completeness of the information, text, graphics, links or other items contained
within these materials. Your use of this Document is at your own risk. Ogemaw, its suppliers, and other parties involved
LQ FUHDWLQJ DQG GHOLYHULQJ WKLV 'RFXPHQW¶V FRQWHQWV VKDOO QRW EH OLDEOH IRU DQ\ VSHFLDO LQGLUHFW LQFLGHQWDO RU
consequential damages, including without limitation, lost revenues or lost profits.

OEM Labeling Requirements

USERS MANUAL OF THE END PRODUCT:

In the user's manual of the end product, the end user has to be informed to keep at least 20cm separation with the
antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency
exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any
changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this
equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required
to be available in the user's manual:

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party Responsible for compliance
FRXOGYRLGWKHXVHU¶VDXWKRULW\WRRSHUDWHWKLVHTXLSPHQW

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX
FCC ID: 2AATW-20140913AP ". If the size of the end product is larger than 8x10cm, then the following FCC part
15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled Environment.
This equipment should be installed and operated with minimum distance 20cm. Between the radiator &
your body.

Attention
The OEM integrator is still responsible for the FCC compliance requirement of the end product, which
integrates this module. Appropriate measurements (e.g. 15 B compliance) and if applicable additional
equipment authorizations (e.g. Verification , Doc) of the host device to be addressed by the
integrator/manufacturer.

This RF Module does not have an own shielding, so that a Limited Modular Approval (LMA) was granted:
This RF module is strictly limited to the integration by the Grantee himself or the dedicated OEM
integrators under the control of the Grantee. and This LMA with a Integral antenna, antenna gain is
0.0dBi.
Proper measurements of the host device including this RF module (radiated spurious emissions and bandage) are
required to assure compliance with the FCC regulations.

Any other integrator must contact the Grantee to determine necessary compliance measurements and/or additional
equipment authorizations (e.g. Class II Permissive Change or New Equipment Authorization) for his
configuration. This RF Module must not be sold to the general public.

IMPORTANT NOTE: In the event that these conditions cannot be met (for example: certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID
cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Changes or
modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.