Kenwood Kdc-Bt565u Kdc-x500 Kdc-x5000bt Kmr-d765bt SM

SERVICE MANUAL
CD RECEIVER
SERVICE MANUAL
11
2015
WA185<Rev.001>
KDC-BT565U, KDC-X500,
KDC-X5000BT, KMR-D765BT
DETACHABLE PANEL
Model Parts number
KDC-BT565U CP-CBT565UKW
KDC-X500 CP-CX500KW
KDC-X5000BT CP-CX5000BTEW
KMR-D765BT CP-RD765BTKW
DC cord DC cord Screw set Tap screw (M2x8) Microphone

(E3A-0052-00) (QAM1333-001) (GE40531-001A) (QYSPSF2008ZA) (QAN0126-001)
(QAM1399-001)
Hook M. sleeve assy Trim plate Remocon

(GE40578-002A) x2 (GE34826-002A) (GE2035x-00xA) (RC-406)
(QAL1303-004)
This product uses Lead Free solder.

PbF
This product complies with the RoHS directive for the European market.
COPYRIGHT © 2015 JVC KENWOOD Corporation
COPYRIGHT © 2015 JVC KENWOOD Corporation No.WA185<Rev.001>

2015/11
SPECIFICATION
Models for destination "K" (KDC-BT565U, KDC-X500, KMR-D765BT)
Tuner
FM Frequency Range 87.9 MHz to 107.9 MHz (200 kHz space)
Usable Sensitivity (S/N = 26 dB) 8.2 dBf (0.71 µV/75 Ω)
Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 µV/75 Ω)
Frequency Response (±3 dB) 30 Hz to 15 kHz
Signal-to-Noise Ratio (MONO) 64 dB
Stereo Separation (1 kHz) 40 dB
AM Frequency Range 530 kHz to 1 700 kHz (10 kHz space)
Usable Sensitivity (S/N= 20 dB) 29 dBµ (28.2 µV)
CD player
Laser Diode GaAIAs
Digital Filter (D/A) 8 times over sampling
Spindle Speed 500 rpm to 200 rpm (CLV)
Wow & Flutter Below Measurable Limit
Frequency Response (± 1 dB) 20 Hz to 20 kHz
Total Harmonic Distortion (1 kHz) 0.01%
Signal-to-Noise Ratio (1 kHz) 105 dB (Except KDC-X500), 110 dB (KDC-X500)
Dynamic Range 90 dB
Channel Separation 85 dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
AAC Decode AAC-LC ".aac" files
USB
USB Standard USB 1.1, USB 2.0 Full Speed
File System FAT12/16/ 32
Maximum Supply Current DC 5 V 1.5 A
WAV Decode Linear-PCM
FLAC Decode FLAC file (Up to 48 kHz / 16 bit)
Bluetooth
Version Bluetooth Ver.2.1+EDR/ Bluetooth 3.0
Frequency Range 2.402 GHz to 2.480 GHz
Output Power +4 dBm (MAX), 0 dBm (AVE), Power Class2
Maximum Communication range Line of sight approx. 10 m (32.8 ft)
Profile HFP (Hands-Free Profile), A2DP (Advanced Audio Distribution Profile), AVRCP
(Audio/Video Remote Control Profile), SPP (Serial Port Profile), PBAP (Phone-
book Access Profile)
Auxiliary
Input Maximum Voltage 1 000 mV
Input Impedance 30 kΩ
Audio
Maximum Output Power 50 W × 4
Full Bandwidth Power 22 W × 4 (at less than 1 % THD)
Speaker Impedance 4Ω-8Ω
Tone Action Band 1: 62.5 Hz ±9 dB, Band 2: 100 Hz ±9 dB, Band 3: 160 Hz ±9 dB, Band 4: 250
Hz ±9 dB, Band 5: 400 Hz ±9 dB, Band 6: 630 Hz ±9 dB, Band 7: 1 kHz ±9 dB,
Band 8: 1.6 kHz ±9 dB, Band 9: 2.5 kHz ±9 dB, Band 10: 4 kHz ±9 dB,
Band 11: 6.3 kHz ±9 dB, Band 12: 10 kHz ±9 dB, Band 13: 16 kHz ±9 dB
Preout Level / Load (CD) 4 000 mV/10 kΩ (Except KDC-BT565U), 2 500 mV/10 kΩ (KDC-BT565U)
Preout Impedance ≤ 600 Ω
General
Operating Voltage 14.4 V (10.5 V to 16 V allowable)
Maximum Current Consumption 10 A
Operational Temperature Range -10°C to +60°C
Installation Size (W × H × D) 182 mm × 53 mm × 159 mm (7-3/16" × 2-1/8" × 6-1/4")
Weight 1.3 kg (2.87 lbs)
Subject to change without notice.
(No.WA185<Rev.001>)2/51
SPECIFICATION
Model for destination "E" (KDC-X5000BT)
Tuner
FM Frequency Range 87.5 MHz to 108.0 MHz (50 kHz space)
Usable Sensitivity (S/N= 26 dB) 0.71 µV/75 Ω
Quieting Sensitivity (DIN S/N = 46 dB) 2.0 µV/75 Ω
Signal-to-Noise Ratio (MONO) 64 dB
Stereo Separation (1 kHz) 40 dB
MW Frequency Range 531 kHz to 1 611 kHz (9 kHz space)
Usable Sensitivity (S/N= 20 dB) 28.2 µV
LW Frequency Range 153 kHz to 279 kHz (9 kHz space)
Usable Sensitivity (S/N= 20 dB) 50 µV
CD player
Laser Diode GaAIAs
Digital Filter (D/A) 8 times over sampling
Spindle Speed 500 rpm to 200 rpm (CLV)
Wow & Flutter Below Measurable Limit
Total Harmonic Distortion (1 kHz) 0.01%
Signal-to-Noise Ratio (1 kHz) 105 dB
Dynamic Range 90 dB
Channel Separation 85 dB
USB
USB standard USB 1.1, USB 2.0 Full Speed
File System FAT12/16/ 32
Maximum Supply Current DC 5 V 1.5 A
WAV Decode Linear-PCM
FLAC Decode FLAC file (Up to 48 kHz / 16 bit)
Bluetooth
Version Bluetooth Ver.2.1+EDR/ Bluetooth 3.0
Frequency Range 2.402 GHz to 2.480 GHz
Output Power +4 dBm (MAX), 0 dBm (AVE), Power Class2
Maximum Communication range Line of sight approx. 10 m (32.8 ft)
Profile HFP (Hands-Free Profile), A2DP (Advanced Audio Distribution Profile), AVRCP
(Audio/Video Remote Control Profile), SPP (Serial Port Profile), PBAP (Phone-
book Access Profile)
Audio
Maximum Output Power 50 W × 4
Full Bandwidth Power 22 W × 4 (at less than 1 % THD)
Speaker Impedance 4Ω-8Ω
Tone Action Band 1: 62.5 Hz ±9 dB, Band 2: 100 Hz ±9 dB, Band 3: 160 Hz ±9 dB, Band 4: 250
Hz ±9 dB, Band 5: 400 Hz ±9 dB, Band 6: 630 Hz ±9 dB, Band 7: 1 kHz ±9 dB,
Band 8: 1.6 kHz ±9 dB, Band 9: 2.5 kHz ±9 dB, Band 10: 4 kHz ±9 dB,
Band 11: 6.3 kHz ±9 dB, Band 12: 10 kHz ±9 dB, Band 13: 16 kHz ±9 dB
Preout Level/Load (CD) 4 000 mV/10 kΩ
Preout Impedance ≤ 600 Ω
Auxiliary
Input Maximum Voltage 1 000 mV
IInput Impedance 30 kΩ
General
Operating Voltage 14.4 V (10.5 V - 16 V allowable)
Maximum Current Consumption 10 A
Operational Temperature Range -10°C to +60°C
Installation Size (W × H × D) 182 mm × 53 mm × 159 mm
Weight 1.3 kg
Subject to change without notice.
(No.WA185<Rev.001>)3/51
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and 1.4 Critical parts for safety
many circuits and components specially for safety purpos- In regard with component parts appearing on the silk-screen
es. For continued protection, no changes should be made printed side (parts side) of the PWB diagrams, the parts that are
to the original design unless authorized in writing by the printed over with black such as the resistor ( ), diode ( )
manufacturer. Replacement parts must be identical to and ICP ( ) or identified by the " " mark nearby are critical
those used in the original circuits. Services should be per- for safety. When replacing them, be sure to use the parts of the
formed by qualified personnel only. same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should 1.5 Remote control
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the The Lithium battery is in danger of explosion if replaced incor-
manufacture of responsibility for personal injury or property rectly. Replace it only with the same or equivalent type.
damage resulting therefrom.
1.6 Preventing static electricity
(3) Many electrical and mechanical parts in the products have Electrostatic discharge (ESD), which occurs when static electric-
special safety-related characteristics. These characteris- ity stored in the body, fabric, etc. is discharged, can destroy the
tics are often not evident from visual inspection nor can the laser diode in the traverse unit (optical pickup). Take care to pre-
protection afforded by them necessarily be obtained by us- vent this when performing repairs.
ing replacement components rated for higher voltage, watt- 1.6.1 Grounding to prevent damage by static electricity
age, etc. Replacement parts which have these special Static electricity in the work area can destroy the optical pickup
safety characteristics are identified in the Parts List of Ser- (laser diode) in devices such as laser products.
vice Manual. Electrical components having such features Be careful to use proper grounding in the area where repairs are
are identified by shading on the schematics and by ( ) on being performed.
the Parts List in the Service Manual. The use of a substitute (1) Ground the workbench
replacement which does not have the same safety charac- Ground the workbench by laying conductive material (such
teristics as the recommended replacement parts shown in as a conductive sheet) or an iron plate over it before plac-
the Parts List of Service Manual may create shock, fire, or ing the traverse unit (optical pickup) on it.
other hazards. (2) Ground yourself
Use an anti-static wrist strap to release any static electricity
(4) The leads in the products are routed and dressed with ties, built up in your body.
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed (caption)
that they have been returned to normal, after reassem- Anti-static wrist strap
bling.
1M
1.2 Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
Conductive material
(5) If mains voltage selector is provided, check setting for local
(conductive sheet) or iron plate
voltage.
(3) Handling the optical pickup
1.3 Caution • In order to maintain quality during transport and before
installation, both sides of the laser diode on the replace-
Burrs formed during molding may be left over on some parts ment optical pickup are shorted. After replacement, re-
of the chassis. turn the shorted parts to their original condition.
Therefore, pay attention to such burrs in the case of pre- (Refer to the text.)
forming repair of this system. • Do not use a tester to check the condition of the laser di-
ode in the optical pickup. The tester's internal power
source can easily destroy the laser diode.
(No.WA185<Rev.001>)4/51
1.7 Handling the traverse unit (optical pickup) 1.8 Attention when traverse unit is decomposed
(1) Do not subject the traverse unit (optical pickup) to strong *Please refer to "Disassembly method" in the text for the
shocks, as it is a sensitive, complex unit. pickup unit.
(2) Cut off the shorted part of the flexible cable using nippers, • Apply solder to the short land sections before the card wire is
etc. after replacing the optical pickup. For specific details, disconnected from the connector on the servo board. (If the
refer to the replacement procedure in the text. Remove the card wire is disconnected without applying solder, the pickup
anti-static pin when replacing the traverse unit. Be careful may be destroyed by static electricity.)
not to take too long a time when attaching it to the connec- • In the assembly, be sure to remove solder from the short land
tor. sections after connecting the card wire.
(3) Handle the flexible cable carefully as it may break when
subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that ad-
justs the laser power. Do not turn it. SOLDER
1.9 Important for laser products
1.CLASS 1 LASER PRODUCT 5.CAUTION : If safety switches malfunction, the laser is able
to function.
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation 6.CAUTION : Use of controls, adjustments or performance of
when open. Do not stare into beam. procedures other than those specified here in may result in
(Others) Visible and/or invisible class 1M laser radiation hazardous radiation exposure.
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when

open and inter lock failed or defeated. Avoid direct
exposure to beam. ! Please use enough caution not to
see the beam directly or touch it
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which in case of an adjustment or operation
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is check.
dangerous to defeat the safety switches.
(No.WA185<Rev.001>)5/51
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1 How to repair a fuse pattern
2.1.1 Purpose of fuse pattern
In order to prevent serious damage on the circuit, fuse pattern is prepared on the GND line of RCA Terminal. This damage may
take due to improper part replacement with a external equipment via RCA line.
2.1.2 Repair Procedure
(1) Check the shorted circuit at the meltdown point.
Need to clean up if the shorted circuit or carbonization happen at the fuse pattern.
(2) Add following part on the fuse pattern.
(3) Check output level.
Meltdown point
Part Number Part Name SPEC

F53-0513-08 PATTERN FUSE 4A
2.1.3 After finished repair
Due to improper part replacement, this meltdown occurs.
Thus please notice following information when the unit is returned to your customer.
Things to be checked before installing the unit.
(1) Check the GND line of external amplifier or other equipment which must connect properly.
(2) Check whether the GND line is not short-circuited with the battery terminal. (do not short-circuit these lines)
(No.WA185<Rev.001>)6/51
2.2 Microcomputer’s terminal description
IC701 (STA1080) on MAIN PWB ASSY
Processing/Operation/
Pin No. Pin Name I/O Application
Description
A1 NC - To be left floating
A2 SXM_DATA_SYS O SXM Data Output(For SXM model only)
A3 IPOD_SDA O iPod Authentication IC I2C Data
A4 IPOD_SCL O iPod Authentication IC I2C Clock
A5 MRC_REQ_SYS O Command Request from SYS-com to Marine REMO
(For MARINE model)
A6 TU_SDA I/O I2C Data for Tuner
A6 EP_SDA I/O I2C Data for E2PROM
A6 BT_EP_SDA I/O I2C Data for EEPORM in BT module
A7 TU_SCL I/O I2C Clock for Tuner
A7 EP_SCL I/O I2C Clock for E2PROM
A7 BT_EP_SCL I/O I2C Clock for EEPORM in BT module
A8 PCB_TEST_MODE_RX I PCB Test Mode RX
A8 SD_CLK I/O SD clock. For flashing purpose
A9 SD_CMD I/O SD command output and response input signal. For flashing pur-
pose.
A9 Debug_1A O For debug
A10 NC O No Use
A11 SW2 I CD Mecha SW2
A11 NC O No Use (for mechaless model)
A12 NC O This pin is latched on the rising edge of System reset to define
the debug source to the main Jtag . After reset this pin can be
used as GPIO
A13 NC I Radio On/off signal.
A14 NC I This signals is used by power management unit (PMU) to detect
if external power is OK. The PMU move to Normal state is VD-
DOK=1.
A15 NC I Ignition key signal. Used by PMU
A16 REG_FLG I Power Detection L: Detect OFF /
H: Detect ON
A17 PAN_DET I Panel Detection input L: Panel Attached /
H: Panel Detached
A18 MRC_REQ_MRC I Command Request from Marine REMO to SYS-com
(For MARINE model) (Need to set into interrupt pin)
A19 GND - GND
B1 SXM_DATA_SXM I SXM Data Input(For SXM model only)
B2 REMAP1 I [ST] REMAP0 and REMAP1 are used to detect and define the
boot device (NAND, NOR, SDMMC, UART). These pins are
latched at the rising edge of System reset
B3 MRC_DATA_MRC I Marine REMO Data Input UART (For MARINE model)
B4 MRC_DATA_SYS O Marine REMO Data Output UART (For MARINE model)
B4 UART_Flash1 O UART Flashing need to pull down (for debug / flashing use)
B5 BEEP I/O Output for Beep Tone Generator H(Pulse):BEEP / L:OFF
B6 RESET I Reset Input
B7 CD_DSP_SW O CD DSP Switch L: Other sources /
H: CD, USB, SD source
B7 NC O No Use (for mechaless model)
(No.WA185<Rev.001>)7/51
Description
B8 NC O No Use
B9 PCB_TEST_MODE_TX O PCB Test Mode TX
B10 NC O No Use
B11 NC O No Use
B12 NC O No Use (for mechaless model)
B13 DRV_Lo/Ej O Loading Motor Control Output
B13 NC O Loading Motor Control Output
B14 NC I Low battery voltage signal. Used by PMU to change the state of
the system (Normal, standby)
B15 M3_PWREN O Used by PMU to enable external voltage regulator , when a wake
up event has been detected
B16 DRV_CNT O Loading Motor Control Output
B17 DAC_VHI - Analog High reference , it require a 10nF and 10uF capacitors
connected to DAC_AGND
B18 SPK_RL O Speaker Rear Left channel output
B19 SW_R O Subwoofer Right channel output
C1 SXM_PWR O Power Supply for SXM(For SXM model only) L: PWR Off / H: PWR On
C2 SQI_SIO3 I/O Serial NOR data line 3
C3 REMAP0 I Memory remap pin. These pin are latched on the rising edge of
System reset, and define the boot de-vice.
C4 MRC_EN O Marine REMO Data Select (For MARINE model)
C5 MRC_PON O Enable Marine REMO Power Supply (For MARINE model) H:Power On / L:Power Off
C6 NC O No Use
C7 REG_SCL O I2C Clock for Regulator IC
C8 SD_DATA I/O Data lines for SD or MMC card. For flashing purpose
C8 Debug_1B O For debug
C9 BCLK I Servo DSP Data Bit Clock
C9 NC O No Use (for mechaless model)
C10 NC O No Use
C11 MDATA O Microcontroller Command Data Signal
C12 MCLK O Microcontroller Command Clock Signal
C13 PSW I CD Mecha Position Setting SW (Reset Switch)
C14 M3_SXTALI O Crystal output , 32kHz RTC clock
C15 SW1 I CD Mecha SW1. Need interrupt function.
C16 LCD_DATA_LCD I LCD DATA Intput (for LCD Model)
C17 DAC_VLO - Analog Low Reference; connect it to DAC_AGND
C18 SPK_FL O Speaker Front Left channel output
C19 SW_L O Subwoofer Left channel output
D1 SQI_SCK O Serial NOR clock
D2 SQI_SIO1 I/O Serial NOR data line 3
D3 SQI_CE0n O Chip select for Serial Nor memory (SQI flash enable)
D4 SQI_SIO0 I/O Serial NOR data line 0
(No.WA185<Rev.001>)8/51
Description
D5 NC O No Use
D6 NRST O LSI Reset Signal (L= Reset) L: Reset ON / H: Reset OFF
D6 NC O No Use (for mechaless model)
D7 MLD O Microcontroller Command Load Signal
D8 REG_SDA O I2C Data for Regulator IC
D9 STAT I DSP Status Signal
D10 LRCK I Servo DSP Data Word Clock
D10 NC O No Use
D11 CD_SRDATA_CD I Servo DSP Data Input
D12 DRV_MUTE O Motor Driver Control
D13 NC O output 32kHz clock
D14 M3_SXTALO O Crystal output , 32kHz RTC clock
D15 BLKCK I Sub-Code Block Clock Signal
D16 DIM_IN I Dimmer Control Input (for JVC Model) L: Dimmer Detect ON /
H: Dimmer Detect OFF
D16 NC O No Use (for KWD Model)
D17 DAC_VCOM - Common Voltage, it require a 10nF and 10uF capacitors con-
nected to DAC_AGND
D18 SPK_FR O Speaker Front Right channel output
D19 SPk_RR O Speaker Rear Right channel output
E1 SQI_SIQ2 I/O Serial NOR data line 2
E2 SQI_FBSCK I SQI flash clock feedback
E3 NC O No Use
E4 NC O No Use
E5 NC O No Use
E6 VDD_3.3V - 3.3V
E7 VDD_3.3V - 3.3V
E8 VDD_3.3V - 3.3V
E9 VDD 1.2V - 1.2V Core voltage
E10 VDD 1.2V - 1.2V Core voltage
E11 JTAGSEL O Select between Ate test and Debug port; Connect it to GND in
the appliaction.
E12 ADC2_VREFN - Negative reference Voltage of SAR ADC. Connect it to GND
E13 VDD_IO_ON3.3V - 3.3V always on power.
E14 VDD_ON_VREG1.2V - 1.2V always on Voltage, to be con-nected to 2.2nF Capacitor
E15 MIC_BIAS O Bias voltage for Mic. 2.5V +/- 5%.
E16 NC I SAR ADC CH9
E17 NC I No Use
E18 STEERING_REMO2 I OE Remote In 2 (for DOP models)
E19 STEERING_REMO1 I OE Remote In 1 (for DOP models)
F1 NC O No Use
F2 NC O No Use
(No.WA185<Rev.001>)9/51
Description
F3 NC O No Use
F4 NC O No Use
F5 NC O No Use
F6 VDD 1.2V - 1.2V Core voltage
F7 VDD 3.3V - 3.3V
F8 VDD 3.3V - 3.3V
F9 VDD 1.2V - 1.2V Core voltage
F10 OSC32K_GND - GND
F11 GND - GND
F12 GND - GND
F13 ADC2_AGND - Analog 3.3V ground of SAR ADC
F14 DAC_AGND - AGND for DAC
F15 ADC2_VREFP - Full scale Positive reference connect it to 3.3V.
F16 AUX_L I AUX Audio input left channel
F16 SXM_L I SXM Audio input left channel
F17 AUX_R I AUX Audio input right channel
F17 SXM_R I SXM Audio input right channel
F18 TU_L I Tuner Analnog Audio input left channel (for non DAB/HD model)
F18 HD_L I HD Audio input left channel
F18 DAB_L I DAB Audio input left channel
F19 TU_R I Tuner Analnog Audio input right channel (for non DAB/HD mod-
el)
F19 HD_R I HD Audio input right channel
F19 DAB_R I DAB Audio input right channel
G1 NC O No Use
G2 NC O No Use
G3 NC O No Use
G4 NC O No Use
G5 VDD 1.2V - 1.2V Core voltage
G6 VDD 3.3V - 3.3V
G7 GND - GND
G8 GND - GND
G9 GND - GND
G10 GND - GND
G11 GND - GND
G12 GND - GND
G13 ADC2_AVDD - Analog 3.3V supply of SAR ADC
G14 DAC_I/O_AGND - DAC GND
G15 DAC_AVDD - Analog 3.3V for DAC
G16 STAGE1 I Model Selecting Input 1
G17 STAGE2 I Model Selecting Input 2
G18 MIC_P I Microphone input +
G19 MIC_N I Microphone input -
H1 BT_RST O BT Reset Output (For BT model) L: Reset ON /
H: Reset OFF
H2 NC O No Use
(No.WA185<Rev.001>)10/51
Description
H3 NC O No Use
H4 NC O No Use
H5 VDD 1.2V - 1.2V Core voltage
H6 VDD 3.3V - 3.3V
H7 GND - GND
H8 GND - GND
H9 GND - GND
H10 GND - GND
H11 GND - GND
H12 GND - GND
H13 USB_VREG3V3_1V1 - 3.3V supply for embedded 1.1V regulator
H14 ADC0_1_AVDD - Analog 3.3V supply for ADC0 and ADC1
H15 DAC_I/O_AVDD - Analog 3.3V supply for DAC Output
H16 TEL_MUTE I Tel Mute Detection Input (for JVC Model)
H17 NC (Pull down) I SAR ADC CH 0/Touch screen panel signal XP
H18 NC I ADC1 aux differential inputs
H19 NC I ADC1 aux differential inputs
J1 NC O No Use
J2 NC O No Use
J3 NC O No Use
J4 NC O No Use
J5 VDD 1.2V - 1.2V Core voltage
J6 VDD 3.3V - 3.3V
J7 GND - GND
J8 GND - GND
J9 GND - GND
J10 GND - GND
J11 GND - GND
J12 GND - GND
J13 USB_VREG3V3_1V8 - 3.3V supply for embedded 1.8V regulator
J14 ADC0_1_AGND - Analog 3.3V ground for ADC0 and ADC1
J15 ADC0_1_VRFP - Positive reference for ADC0 and ADC1. It require a 10nF and
10uF capacitors connected to GND
J16 ADC0_1_VRFN - Negative reference for ADC0 and ADC1. Connect it to GND.
J17 ADC0_1_VCM - Common Voltage for ADC0 and ADC1.. It require a 10nF and
10uF capacitors connected to GND
J18 NC I No Use
J19 NC I No Use
K1 BT_I2S0_TX O BT digital audio I2S TX data
K2 BT_I2S0_RX I BT digital audio I2S RX data
K3 BT_DATA_BT I BT Data Input(For BT model only)
K4 BT_DATA_SYS O BT Data Output(For BT model only)
K5 VDD 1.2V - 1.2V Core voltage
K6 VDD 3.3V - 3.3V
K7 GND - GND
K8 GND - GND
(No.WA185<Rev.001>)11/51
Description
K9 GND - GND
K10 GND - GND
K11 GND - GND
K12 GND - GND
K13 USB1_VDD3V3 - 3.3V supply for USB1
K14 USB_BGETXT - For test purpose. Leave it unconnected
K15 USB_1.8VREG - Connect it to 4.7 uF capacitor
K16 USB_1.1VREG - Connect it to 4.7 uF capacitor
K17 USB0_AGND - USB analog Ground
K18 D-1 I/O USB Data- 1 (Rear USB)
K19 D+1 I/O USB Data+ 1 (Rear USB)
L1 BT_I2S0_BCLK I/O BT digital audio I2S bit clock
L2 BT_I2S0_FS I/O BT digital audio I2S LR Frame sync
L3 BT_UART0_CTS I UART0 Clear To Send
L4 BT_UART0_RTS O UART0 Request To Send
L5 VDD 1.2V - 1.2V Core voltage
L6 VDD 3.3V - 3.3V
L7 GND - GND
L8 GND - GND
L9 GND - GND
L10 GND - GND
L11 GND - GND
L12 GND - GND
L13 VDD 3.3V - 3.3V
L14 USB0_VDD3V3 - 3.3V supply for USB0
L15 NC - For test purpose. Leave it unconnected
L16 COMP0 - Compensation input needs external 121Kohm res. 1% connect-
ed to GND
L17 USB1_AGND - USB analog Ground
L18 D-0 I/O USB Data- 0 (Front USB)
L19 D+0 I/O USB Data+ 0 (Front USB)
M1 SPI_EN O Command request from main to Flash IC (iAP2) L: Enable / H: Disable
M2 SPI_CLK I/O Clock to Flash IC (iAP2)
M3 SPI_DATA_SPI I Flash (iAP2) data input
M4 SPI_DATA_SYS O Flash (iAP2) data output
M5 VDD 1.2V - 1.2V Core voltage
M6 VDD 3.3V - 3.3V
M7 VDD 3.3V - 3.3V
M8 VDD 3.3V - 3.3V
M9 VDD 3.3V - 3.3V
M10 VDD 3.3V - 3.3V
M11 VDD 3.3V - 3.3V
M12 VDD 3.3V - 3.3V
M13 VDD 3.3V - 3.3V
M14 VDD 3.3V - 3.3V
M15 PLL_GND - GND
(No.WA185<Rev.001>)12/51
Description
M16 PLL_VDD2.5V - SOC PLL 2.5V output voltage , to be connected to a 4.7uF ca-
pacitor
M17 VREG_BYPASS - Connect it to GND on application board
M18 USB_REXT - Connect to GND with a 3Kohm 1% resistors
M19 FREQ_SEL O Frequency Select Pulse: Power On /
L: Power Off
N1 DAB_CLK_SYS I/O Clock to DAB (for DAB model only)
N1 HD_CLK_SYS I/O Clock to HD Decoder (for HD model only)
N2 NC O No use
N3 DAB_DATA_DAB I DAB Data Input (for DAB model only)
N3 HD_DATA_HD I HD Data Input (for HD model only)
N4 DAB_DATA_SYS O DAB Data Output (for DAB model only)
N4 HD_DATA_SYS O HD Data Output (for HD model only)
N5 VDD 1.2V - 1.2V Core voltage
N7 VDD 3.3V - 3.3V
N8 VDD 3.3V - 3.3V
N9 VDD 3.3V - 3.3V
N14 NC O No use
N15 PLL_VREG3.3V - 3.3V for embedded PLL voltage regulator
N16 USB_PON0 O Enable Output for High Side Switch (Front USB)
N17 NC O No Use
N18 XTAL O Crystal output
N19 EXTAL I Crystal input , 24MHz System clock
P1 NC O No Use
P2 REMO I Remocon Input L (Pulse): Remote control
data / H: Standby
P3 DAB_REQ_DAB I Command Request from DAB micon to main micon (to be set
into interrupt point)
P4 TU_RST O HELIO / CAYMAN (HD) Reset L: Reset ON /
H: Reset OFF
P5 Reserved - Reserved
P16 NC I/O Data lines for SD or MMC card
(No.WA185<Rev.001>)13/51
Description
P17 NC I/O Data lines for SD or MMC card
P18 NC O Command line for Sd or MMC card
P19 NC O No Use
R1 LCD_CE O LCD Driver IC Chip Enable Output (for LCD Model)
R2 LCD_DATA_SYS O LCD DATA Output (for LCD Model)
R3 LCD_DATA_LCD I LCD DATA Intput (for LCD Model)
R4 LCD_CLK O LCD CLK Output
R5 Reserved - Reserved
R16 NC I/O Data lines for SD or MMC card
R17 NC I/O Data lines for SD or MMC card
R18 NC O Clock Line for Sd or MMC card
R19 OFFSET I Power IC offset signal
T1 JTAG_TDI I Primary JTAG port data in (can be connnected to M3 or R4 Jtag)
T2 JTAG_TDO O Primary JTAG port data out (can be connnected to M3 or R4
Jtag)
T3 JTAG_TCK I Primary JTAG port clock (can be connnected to M3 or R4 Jtag)
T4 JTAG_TMS I Primary JTAG port mode select (can be connnected to M3 or R4
Jtag)
T5 Reserved - Reserved
T16 PWIC_STBY O Output to Power On Power Amp IC L: Standby / H: Play
T17 UART_Flash2 O UART Flashing need to pull down (for debug / flashing use)
T18 USB_PON1 O Enable Output for High Side Switch (Rear USB)
T19 NOISE CTRL O Enable attenuation circuit to control noise level during low vol- H: ON (vol 0 to vol 10),
ume. L: Off ( vol 11 to vol 35)
U1 NC O No Use
(No.WA185<Rev.001>)14/51
Description
U2 JTAG_TRSTn I Primary JTAG port reset (can be connnected to M3 or R4 Jtag).
If JTAG/Debug is used,TRSTn must transit from LOW to HIGH
before or at same time as PORn. If JTAG/Debug is not used,
TRSTn can be left unconnected.
U3 Reserved - Reserved
U18 DC_ERR2 I Detect DC Clip (for ST Power Amp IC) L: DC Error ON /
H: DC Error OFF
U19 MUTE O Muting Output for Evol & Line Out L: Mute ON / H: Mute OFF
V1 ENC1 I Volume Encoder Pulse Input 1
V2 ENC2 I Volume Encoder Pulse Input 2
V3 RGB_CLK O I2C Clock Output for RGB Driver (For RGB Model)
V4 DAB_REQ_SYS O Command Request from main micon to DAB micon (for DAB
model)
V5 NC O No Use
V6 NC O No Use
V7 NC O No Use
V8 NC O No Use
V9 NC O No Use
V10 NC O No Use
V11 NC O No Use
V12 NC O No Use
V13 NC O No Use
V14 NC O No Use
V15 NC O No Use
V16 NC O No Use
V17 NC O No Use
V18 NC O No Use
V19 PWIC_MUTE O Muting Output for Power Amp IC L: Mute ON / H: Mute OFF
W1 GND - GND
W2 Field Test 1 O RDS data log output (standby for field test)
W3 Field Test 2 O RDS data log output (standby for field test)
W4 DAB_COM_ON O Enable DAB micon (For DAB model) H: ON / L: OFF
W5 NC O No Use
(No.WA185<Rev.001>)15/51
Description
W6 NC O No Use
W7 NC O No Use
W8 NC O No Use
W9 NC O No Use
W10 NC O No Use
W11 NC O No Use
W12 NC O No Use
W13 NC O No Use
W14 NC O No Use
W15 AUD SEL O Audio Selector to select AUX or SXM H: SXM / L: AUX
W16 PCB_TEST_MODE I PCB Test Mode Switch L: Normal Mode /
H: Check Mode (After Re-
set, software need to
check the pin input. If de-
tect high, it should enter
Serial Number mode)
W17 NC O No Use
W18 NC O No Use
W19 GND - GND
(No.WA185<Rev.001>)16/51
SECTION 3
DISASSEMBLY
3.1 Main body (4) Remove the 2 screws C, and remove the MAIN PWB.
3.1.1 Removing the MAIN PWB (See Fig.1 to 5) (See Fig.4)
(1) Disengage the 4 hooks a, and remove the BOTTOM
COVER. (See Fig.1) C
a a
a
a
C
MAIN PWB
BOTTOM COVER Fig.4
Fig.1 (5) Disconnect the FFC wire from connector CN1. (See Fig.5)
(2) Disengage the 6 hooks a, and remove the FRONT
CHASSIS ASSY. (See Fig.2)
b b
b b
b b
FRONT CHASSIS ASSY

Fig.2
(3) Remove the 1 screw A and 2 screws B. (See Fig.3)
A
CN1
Fig.5
B B
Fig.3
(No.WA185<Rev.001>)17/51
3.1.2 Removing the CD MECHANISM (See Fig.6) 3.2 CD mechanism
(1) Remove the 3 screws D, and remove the CD MECHA- • NOTICE FOR HANDRIG OF MECHANISM ASSY
NISM. (See Fig.6)
OK
D D Handle CHASSIS part.
NG
Do not stay MECHANISM ASSY in upside-down condition
for 1 hour and more.
CD MECHANISM
D
Fig.6
3.1.3 Removing the SWITCH PWB (See Fig.7)
(1) Remove the VOLUME KNOB.
(2) Remove the 4 screws E.
(3) Disengage the 10 hooks c, and remove the REAR COVER.
(4) Remove the SWITCH PWB.
NG
E E Do not touch P.C.B..
c c c c Do not touch DAMPER.
c
c
Do not touch
PICK UP ASSY.
c
c c c
REAR COVER
E E
Fig.7 NG
TOP SIDE BOTTOM SIDE
DO NOT TOUCH AREA

DO NOT TOUCH HOLES, MOTOR, DAMPER, PCB, FFC, OPU AND WIRE.
• THESE PARTS NEED CAUTION OF HANDLING

CAUTION:
Don't touch the following parts in particular by the hand which
touched grease. (It becomes a cause of traction problem)
CAUTION PARTS
HC TURN TABLE TRIGGER ARM
ROLLER DISC GUIDE
(No.WA185<Rev.001>)18/51
• NOTICE FOR HANDRIG OF FEED MOTR ASSY 3.2.1 Removing the CD Player unit (See Fig.1 to 3)
CAUTION: For mounting FEEDMOTOR ASSY, DON'T bump this part. (1) Solder the short land on the Pickup. (See Fig.1)
Because handling may cause this part easily deformed.
SOLDER
FEED MOTOR
WORM 1
• NOTICE FOR HANDRIG OF ROLLER LEVER ASSY

OK NG
Fig.1
(2) Remove the 6 wires from the CD Player unit. (See Fig.2)
Do not handle roller part. Black

• NOTICE FOR CLAMPER ASSY OF PICK UP ASSY
Red
OK NG
Yellow
Orange White
Do not handle
the clamper part. Orange
Fig.2
(3) Disconnect the FPC wire from the connector CN1 (CD
Player unit). (See Fig.3)
(4) Remove the 2 screws A, and remove the CD Player unit.
(See Fig.3)
• NOTICE FOR HANDRIG OF MD CHASSIS ASSY

NG
OK A
Handle CHASSIS part.
Do not handle the

turn table part.
• NOTICE FOR HANDRIG OF PICK UP ASSY
OK NG
CN1 CD Player unit

Fig.3
Do not handle the lens part.
(No.WA185<Rev.001>)19/51
3.2.2 Removing the Traverse mechanism (See Fig.4, 5) 3.2.3 Removing the Pickup assy (See Fig.6)
(1) Remove the 4 springs from the traverse mechanism. (1) Remove the 1 screw C.
(See Fig.4) (2) Remove the Main shaft in the direction of the arrow.
(3) Remove the Spring.
Spring (4) Remove the Pickup assy.
C Main shaft Pickup assy
Spring
Fig.6
3.2.4 Removing the Roller lever assy (See Fig.7)
Fig.4 (1) Remove the Spring.
(2) Remove the 2 screws B attaching the Lower chassis. (2) Remove the Roller lever assy in the direction of the arrow.
(See Fig.5) Spring
(3) Remove the Damper in the direction of the arrow. Roller lever assy
(See Fig.5)
(4) Remove the Traverse mechanism. (See Fig.5)
Traverse mechanism
Damper
Lower chassis
Fig.7
B
Fig.5
(No.WA185<Rev.001>)20/51
3.2.5 Removing the Clamp arm assy (See Fig.8)
(1) Remove the Spring.
(2) Remove the Clamp arm assy in the direction of the arrow.
Clamp arm assy Spring
Fig.8
3.2.6 Removing the Feed motor (See Fig.9, 10)
(1) Remove the 4 screws D, remove the Feed motor assy.
(See Fig.9)
D
Fig.9
(2) Remove the 2 screws E, remove the Feed motor. (See
Fig.10)
E
Feed motor
Fig.10
(No.WA185<Rev.001>)21/51
SECTION 4
ADJUSTMENT
4.1 Outline
4.1.1 Panel
ACCENT EJECT
SEARCH RETURN VOL / ROTARY
A symbol "" in the key column indicates that the key should be pressed and held for 1 second or longer.
4.1.2 Test Modes
These test modes are available in normal production ROM.
Transition to Test Mode shall be available during DC Error detection.
Test Mode Mode Source Operation
Production Test Mode - All Press and hold [1] key and [3] key and reset.
Service Test Mode Normal Mode / Standby Pressing and holding [2] key, press [6] key for 7 seconds.
Production Mode (Starting to press [2] key and [6] key at the same time can not be
entered into the mode)
Service Information Clear Mode - All Press and hold [2] key and [5] key and reset.
DC Error Information Mode - All Press and hold [3] key and [6] key and reset.
Diagnostic Data Mode - SXM Pressing and holding [RETURN] key, press [DISP] key for 7 sec-
onds.
(Starting to press [RETURN] key and [DISP] key at the same time
can not be entered into the mode)
DC Offset Calibration Mode Normal Mode Standby Pressing and holding [2] key, press [3] key for 3 seconds.
(Starting to press [2] key and [3] key at the same time can not be
entered into the mode)
DOP USB SET / DOP Test Mode Normal Mode Standby Pressing and holding [6] key, press [VOLUME] key for 7 seconds.
(Starting to press [6] key and [VOLUME] key at the same time can
not be entered into the mode)
Default Mode: DOP USB SET
Turn [VOLUME] to change mode to DOP Test Mode.
HC Mecha Running Mode - All Press and hold [SRC] key and [EJECT] key and reset.
Tunisia Area / Normal Mode All Pressing and holding [1] key and [5] key, then Power On (During
Tuner Span Change Mode power off).
4.1.3 Release from Test Mode
These actions will release the Test Mode and transit back to Normal Mode
Method Remarks
Reset All Modes
Momentarily voltage drop All Modes
ACC OFF All Modes
POWER OFF All Modes
Panel Detach All Modes
Source Change Diagnostic Data Mode only
(No.WA185<Rev.001>)22/51
4.2 Production Test Mode
Press and hold [1] key and [3] key and reset.
4.2.1 Test Mode Defaults
During Production Test Mode, the following settings defer from the Normal Mode.
The settings will change immediately after mode activation.
Difference in action Setting value
Period to prohibit TEL/LINE MUTE function (Normal Mode: 10 secs) 1 second
Mecha Initialize Action Prohibited
Writing-in to E2PROM when DC error is detected Prohibited
"DEMO" item in Setup Menu Prohibited
Power supply during ACC OFF (Back Up On) MUTE terminal turns OFF after 2 seconds
"BEEP" item in Setup Menu Beep with short-press in any function
Volume range 0 to 35
Source change interval timer 0 seconds
When 0-bit mute is detected Mute off
Various setting item Setting value

Default Volume 33
"BASS BOOST" OFF
"LOUDNESS" OFF
Initial Source Standby
Language English
Extra EQ OFF
EQ NATURAL
Fader / Balance Center
Digital Track Expander / Sound Reconstruction Set OFF
"VOL ADJUST" / "VOLUME OFFSET" -6: Only SXM source, 0: Other sources
DEMO Mode Setting OFF
RGB Setting (RGB Models only) R = 9, G = 9, B = 9 (White)
Sub-woofer/ Rear (For L/O switchable models) Rear
4.2.2 Mode structure
The following table shows the test modes that can be accessed from the different sources in Production Test Mode.
Source Test mode
Standby Version Display Mode
Tuner TUNER Test Mode
USB USB Test Mode
SXM Sirius XM Test Mode
CD CD Test Mode
(No.WA185<Rev.001>)23/51
4.2.3 Mode content
Syscon shall display the following information after entering Production Test Mode.
Display content Details
All lights on (BOTH LCD & LED including dual color switchable)
Set should not be able to power on if sub clock is not functioning.
The display is released when another operation is executed.
4.2.4 Standby Test Mode
Item Operation Display content Details
Syscom version ## = File Number
display S Y S # # – @ @ @
@@@ = Syscon Version Number
BT module 1 (Toggle) #### = BT version display (4 digits)
version display B T S X X X X
All lights ON All lights ON (Switch with other display)

Serial No. Display (8 digits)
Display to support ASCII characters
Serial No. display S N 0 0 0 0 0 0 0 0
2 (Toggle) ********: Blank
@@@@@@@@: EEPROM Read Error
All lights ON All lights ON (Switch with other display)
All lights ON/OFF with toggle
All lights ON/OFF 3 (Toggle)
## = Blank: Verifying
OK: IC mounted
NG: IC not mounted
**: Non iPod support model
iPod IC Mount
Verification Status
In addition, upon entering this mode, P-CON is
Display : #
4 (Toggle)
i P o d #
turned ON.
(USB models
only)
When a result is OK, P-CON is turned off.
Upon exit, P-CON remains OFF.
When a result is NG, P-CON is kept ON condition.
Upon exit, P-CON remains ON.
All lights ON All lights ON (Switch to other display)
Pre-out Switch Switch Pre-out with toggle
S W P R E R E A R
(1 Pre-out / 2 Pre- 5 (Toggle)
out models only) S W P R E S U B - W
All Lights ON/OFF

(Non-RGB Mod- 6 (Toggle) All lights ON/OFF with toggle
els only)
FL display all lights ON and RGB lights ON se-
Vario color Check quence as below:
(RGB Models 6 (Toggle) R=9; G=9; B=9 (White) → R=9; G=0; B=0 (Red) →
only) R=0; G=9; B=0 (Green) → R=0; G=0; B=9 (Blue) →
repeat continuously
SOURCE Return to Normal mode
Mode release
Transition
RETURN All lights ON/OFF with toggle
All lights ON/OFF
(Toggle)
(No.WA185<Rev.001>)24/51
4.2.5 Tuner Test Mode Specification
The following display shall be indicated according to the TUNER status.
Status Display content Details
TUNER IC Communication to TUNER IC not available
Communication Error T U N C O N N G
(indicated unless the mode is in Clock Display Mode).
RDS Specified data Turn OFF P-CON forcibly if PS = RDS TEST is received.
reception R D S T E S T
P-CON recovers with Power OFF/ON.

S meter value
xx: Current S meter value
OK: Within S meter voltage spec (Range 20-25 in
hex value)
NG: Out of S meter voltage spec (Except range 20-
25)
In addition, upon enter to this mode, P-CON is turned

S meter voltage S – M T R x x : O K ON.
ACCENT
judgment display S – M T R x x : N G
When a judgment result is OK, P-CON is turned off.
Upon exit, P-CON still remain OFF.
When a judgment result is NG, P-CON is kept ON
condition.
Upon exit, P-CON still remain ON.
Shift to TUNER setting mode after switching to

98.3MH.
Display TUNER IC version
TUNER IC
ACCENT* AT2 ********' is eg "AtomIC2 57V1B101" indicating
Display A T 2 * * * * * * * *
"AtomIC2 TEF6657V1B 1.01"
BAND switch Execute Band Switch as shown in the following table
BAND
operation F M 1 – 3 A 9 7 . 9
every time Band key is pressed.
*Not applicable and no function for HD and DAB models
4.2.5.1 BAND switch list
Type BAND1 BAND2 BAND3 BAND4 BAND5 BAND6 Details
K (1)FM1 FM2 FM3 (2)AM - - (1)→(2)→(1)...
E (1)FM1 FM2 FM3 (2)MW/LW - - (1)→(2)→(1)...
(No.WA185<Rev.001>)25/51
4.2.6 USB Test Mode Specification
Applicable for iPod model only.
Status Display content Details
## = Blank: Verifying
NG: IC not mounted
**: Non iPod support model
Upon source change to USB source or USB

device plug in:
Verifying: Show "iPod: ##"

NG: Always show "iPod: NG" even during "NO
DEVICE" or playback.
**: Always show "iPod: **" even during "NO
iPod IC Mount Verification Status DEVICE"
: #
Display i P o d #
OK: Change back to nomal display ("NO DE-
VICE / normal playback display).
In addition, upon enter to this mode, P-CON is

turned ON.
When a judgment result is OK, P-CON is

turned off.
Upon exit, P-CON still remain OFF.
When a judgment result is NG, P-CON is kept
ON condition.
Upon exit, P-CON still remain ON.
4.2.7 Sirius XM Test Mode Specification
Upon entering production mode, change to SXM source to enter Sirius XM test mode.
This test mode is to check output and switching of SXV100’s internal tone generator
Communication between Host & SXV100 will be checked.
If the result is OK, a 1kHz signal from the internal tone generator of SXV100 will be outputted.
This test mode will start from Channel 0 automatically.
Left & Right ########: 8 characters Radio ID.
Channel # # # # # # # #
Output 1kHz signal for Left/ Right channel.(Default)
Left Channel RETURN L E F T Output 1kHz signal for Left channel.
(Toggle)
Right Channel R I G H T Output 1kHz signal for Right channel.
Off O F F No signal output (same as normal operation).
4.2.8 CD/ USB Test Mode
Content Details
Playback track from top No.9
Default for Display mode Play time
4.2.8.1 Operations in CDDA playback
Jump to No.15
2.5V Output Level: set Volume value at 27
Special Jump
5 4V Output Level: set Volume value at 25
Operation
(for error operation FCT check of 20Hz 0dB DC pro-
tection)
(No.WA185<Rev.001>)26/51
4.2.9 BT Test Mode Specification
Upon entering production mode, and source changed to BT AUDIO source.
Initial condition of the BT MODE will display as follows.
Initial display
Upon entering this mode, P-CON is turned ON.
B T T E S T M O D E
Note: At TUNER source, Pressing [ACCENT] key
BT AUDIO will not enter to BT Mode
ACCENT
SOURCE BT module error display
When result is OK, P-CON is turned OFF.
B T E R R O R
When result is NG, P-CON is kept ON condition.
TAG dot is lit when the BT module is launched, because it takes time to start the BT module.
TAG dot is flashed during operation of the BT module, and it will be turned off when an error occurs
When module is yet to be fully initiliased, all opera-
BT AUDIO BT TEST tion keys used in the table below, when pressed,
SOURCE MODE P L E A S E W A I T
should show pop out display "PLEASE WAIT" for 1
second.
4.2.9.1 Operations during BT Mode
SOURCE ACCENT Clear the BT MODE and transition to the last source.
Press and hold this key for 2 seconds.
The character string as shown in the left cell is dis-
I N I T I A L I Z E
played while the BT related memory is being initial-
ized.
Clear the BT
related This is to initialize the BT related memory to its fac-
tory default condition.
memory
information *1 When the initialization is successfully completed,
B T I N I T : O K
“...OK”(upper) is displayed, and when the initializa-
B T I N I T : N G
tion is abnormally completed, "...NG" (lower) is dis-
played
(No.WA185<Rev.001>)27/51
Press and hold down for 1 second to perform BT de-
vice search for 15 seconds.
Continue search up to 15 seconds even after a de-
vice is detected.
After 15 seconds, display the device name.
S E A R C H I N G Upon entering this mode, P-CON is turned ON.

Display Blinks (250ms interval)
When result is OK, P-CON is turned OFF.
When result is NG, P-CON is kept ON condition.
It is able to enter into this mode by remote control op-

eration.
SEARCH
/ By Remo- Display the device name when it is detected during
con during search.
BT device search When a different key is pressed after search ends,
any source
except CD X X X X X X X X X X X X X move to the corresponding mode.
source It is able to enter into this mode by remote control op-
eration. P.con will be Low/Off if successful listed all
BT device.
When no device is found at the completion of the
search.
Only for this case, perform the search again by
U N K N O W N pressing the [VOL] key briefly.
Shortcut key for BT Device Search should display
"Unknown" if no device found, P.con will be Keep
Hight/ON for unknown case.
After the completion of the search, press and hold
the [SEARCH] key for 1 second to exit from the test
mode.
• Set the Volume to 15 and turn the internal loop
back function ON by pressing and holding for 1
I N T L O O P F second.
• INT LOOP F: Display internal loop back by FRONT
microphone. (MIC Gain : 8 )
• INT LOOP R: Display internal loop back by REAR
microphone. (MIC Gain : 12)
Internal loop back
VOL • Microphone setting initial value is FRONT for mod-
ON *2
el with microphone setting.
• Display microphone position for each model for
I N T L O O P R model without microphone setting.
• Details of display will not change except [F or R] if
it is on.
To exit loopback, press the [VOL] key once to can-
cel the mode.
*1: This is a function to clear the BT memory information recorded in the EEPROM and the FLASH memory to be initialized with the
"Data flash clear" function, and to write the specific values to initialize it to its factory default condition.
*2: Perform internal LOOP-BACK inspection to check the connection of the built-in microphone (component).
This mode is cleared by reset. (Last status is not retained.)
4.2.9.2 Operations during internal loop back
MIC gain
/ Down with [ ] key, Up with [ ] key
switching M I C G A I N # #
(No.WA185<Rev.001>)28/51
4.3 Service Test Mode
In the STANDBY source, while pressing and holding [2] key, press [6] key for 7 seconds.
(Starting to press [2] key and [6] key at the same time can not be entered into the mode)
4.3.1 Default status immediately after the mode activation
It shall be same as the normal activation.
4.3.2 Mode content
Syscon shall display the following information after entering this mode.
S R V T E S T Display is released when an operation is executed.
4.3.3 Common operation mode for only STANDBY sources

Stage Setting S T A G E 2 1 : # #
BT module BT module software version display

version display B T S X X X X
BT module BT module address display

address 1 (Toggle) X X X X X X X X X X X X
BT module PIN BT module PIN code display

code P I N : X X X X X X X X
BT module BT module friendly name display

friendly name X X X X X X X X X X X X X
00 to 50 are displayed in "XX".

P O N T M : 0 H X X For less than 1 hour, the display is indicated per 10
Power ON minutes.
3
duration display
00001 to 10922 are displayed in "XXXXX".
P O N T M : X X X X x
MAX 10922 (hours)
00 - 50 are displayed in "XX".
C D T M : 0 H X X For less than 1 hour, the display is indicated per 10
Disc action minutes.
4 (*1)(*2)
duration display
00001 to 10922 are displayed in "XXXXX".
C D T M : X X X X X
MAX 10922 (hours)
Disc Eject No. of 00001 to 99999 are displayed in "XXXXX".
5 (*2)
times E J C N T : X X X X X
Disc Eject No. of Clear Disc Eject number of times by pressing for 2
5 (*2)
times clear E J C N T : 0 0 0 0 0
seconds when it is displayed.
*1 This includes all media (CD, USB, iPod, SD) action duration.
*2: Not applicable for mechaless models
(No.WA185<Rev.001>)29/51
4.3.4 CD Error Information Display Mode (Not applicable for mechaless models)
CD error Transit to CD error information display mode.
information
display mode
Mecha error history 1,2,3 (latest)
#:History No. (1,2,3)
XX: kind of errors, "--" when there is none
00: No Error
CD Mecha error 04: TOC read Error
log display M E C H A E R # : X X
05: Unknown CD
06: Heat Error
0A: Update Error
0D: Hold Error
15: Unknown Disc
99: Mecha Error
Load error switch 1,2
CD Load error SEARCH #: Switch No. (1,2)
information (Toggle) L O A D E R # : X X
XX: numbers of errors, "--" when there is none
display
History No. 2 is un-used.
Eject error switch 1,2,3,4
Move
#: History No. (1,2,3,4)
between
CD Eject error XX: numbers of errors, "--" when there is none
items with
information E J E C T E R # : X X History No.3 is un-used
/
display History No.1: Eject before SW1 is on.
History No.2: Eject until SW1 and SW2 is on.
History No.3: Eject between SW2 on and Eject end
CD time code error count information (count skip)
CD time code C N T L O S E
mode display
error count
CD-DA error count numbers
information C D D A : X X
XX: numbers of errors and "--" when there is none
display
(count skip) CD-ROM (compressed file) error count numbers
C D R O M : X X
XX: numbers of errors and “--” when there is none
CD time code error count information
CD time code C N T S T A Y
(count not updated) mode display
error count
CD-DA error count numbers
information C D D A : X X
display
(no count update) CD-ROM (compressed file) error count numbers
C D R O M : X X
CD error Clear CD error information by pressing for 2 seconds
DISP
information clear M E C H A E R # : - -
when it is displayed.
CD error information display mode release, back to
Mode release DISP
Common Mode Operation.
(No.WA185<Rev.001>)30/51
4.4 Service Information Clear Mode
It shall be same as normal activation.
4.4.2 Mode content
After entering this mode, Syscon shall clear the information stored for service and output the result to the display.
CD will be ejected upon process end.
Cleared information changes will take place only after reset.
Display Display content Details
Data Clear in I N I T I A L I Z E Data Clearing in Progress.
Progress
Data Clear OK D A T A C L R : O K Data cleared successfully.
Data Clear NG D A T A C L R : N G Data cleared with error.
Display Blinks (250ms interval) CD is ejected out after the data is being cleared.
The following table shows the data that is cleared.
Information to Clear Details Storage area
CD mecha log display E2PROM
CD load error information display E2PROM
CD mecha information CD eject error information display E2PROM
CD time code error count information display (count skip) E2PROM
CD time code error count information display (no count update) E2PROM
CD EJECT number of times display E2PROM
Service information
Forced Power OFF information display E2PROM
DC error 1 display (wrong connection & other detection information in detecting duration) E2PROM
DC error information
DC error 2 display (capacitor leakage detection number information) E2PROM
Preset Frequency (FM/AM/LW/MW) E2PROM
Preset PI code E2PROM
Preset Frequency (SW) E2PROM
Tuner information Mixed Preset Frequency Band E2PROM
Mixed Preset Frequency E2PROM
Mixed Preset PI Code E2PROM
Tuner Span E2PROM
Pandora information Pandora Preset E2PROM
SXM Preset Channel SID E2PROM
SXM Lock Channel SID E2PROM
SXM Channel Lock Code E2PROM
Sirius XM Information SXM Mature Channel Setting E2PROM
SXM Tune Start Setting E2PROM
SXM Mixed Preset Channel Band E2PROM
SXM Mixed Preset Channel SID E2PROM
Tagging information Token data memory index E2PROM
Language information English/ Russian Language settings E2PROM
BT Pairing Information FLASH ROM
in BT Module
Bluetooth Information
Phonebook Entries of Unit FLASH ROM
(Sent Initialize command to
in BT Module
BT Module)
Call History Entries of Unit FLASH ROM
in BT Module
(No.WA185<Rev.001>)31/51
4.5 DC Error Information Mode
4.5.2 Mode content
D C E R R When DC error is detected.
D C O K
When DC error is not detected.

When wrong connection & DC error in other detec-
D C 1 E R R
tion duration is detected.
DC ERR1display 1
When wrong connection & DC error in other detec-
D C 1 O K
tion duration is not detected.
Clear detection information when wrong connection
DC ERR1 clear 1 D C 1 O K & DC error in other detection duration is displayed.
(Clear data flash)
Display detecting number of times in capacitor leak-
DC ERR2 display 2 D C 2 4 age detection duration.
#: 0 to 4
Clear number of times for detection information in
DC ERR2 clear 2 D C 2 0 capacitor leakage detection duration. (Clear data
flash)
4.6 Diagnostic Data Mode Specification
Press and hold [RETURN] key and [DISP] key for 7 seconds.
(It is necessary to connect tuner box sold separately)
• Sirius XM Diagnostic Data Mode is used to support Sirius XM engineering and technical support.
• The Diagnostic Data Mode is not intended to be routinely accessed by users.
• The Diagnostic Data Mode involves displaying of data reporting in Diagnostic Data Mode messages from the Sirius XM tuner module
and product identifier and revision information.
It shall be same as the normal activation.
4.6.2 Mode content
D I A G M O D E The display is display for 1 second.
4.6.3 Display mode available during Diagnostic Data Mode
In Diagnostic Data Mode, the display can be switch between Diagnostic Mode display and normal mode display using [DISP] key.
The default display mode upon activation is Diagnostic Mode display.
Diagnostic Mode
S I G X # # Default display in diagnostic mode.
Display DISP
Normal Mode (Toggle)
# # # # # # # # # # # # # Depending on display pattern in normal mode.
Display
(No.WA185<Rev.001>)32/51
Signal: 0x00 to 0x04(hex)
Signal Strength S I G X # #
00 to 04 are displayed in "##".
Tuner STS:(hex) "##"
Bit0: PLL Lock, Bit1: Ant Det
Bit2: Ant Undr, Bit3: Ant Ovr
Tuner Status T N R X # #
Bit4: RF AGC Eng,
Bit5: IF AGC Eng
Bit6,Bit7: Reserved
ENSA Lock Status:(hex) "##"
Bit0: T[mcm], Bit1: T[tdm]
ENSA Lock
Bit2: S2[qpsk], Bit3: S2[tdm]
Status L C K A X # #
Bit6,Bit7: Reserved
ENSB Lock Status:(hex) "##"
Bit0: T[mcm], Bit1: T[tdm]
ENSB Lock
Status L C K B X # #
Bit6,Bit7: Reserved
BER S1 B E S 1 # # # BER S1 : 0 to 100 (DEC) "###"
BER S2 B E S 2 # # # BER S2 : 0 to 100 (DEC) "###"
BER T B E T # # # BER T : 0 to 100 (DEC) "###"

Satellite 1 Ensemble A carrier to noise ratio in dB.
The value is reported in 0.25 dB steps.
C/N S1A C N 1 A # # . # #
CN1A: 0.00 to 63.75(dB) (DEC) "##.##"
Eg. 0x3F→63/4 = 15.75 (dB)
Satellite 1 Ensemble B carrier to noise ratio in dB.
ROTARY
C/N S1B Up/Down C N 1 B # # . # #
CN1B: 0.00 to 63.75(dB) (DEC) "##.##"
Eg. 0x3F→63/4 = 15.75 (dB)
Satellite 2 Ensemble A carrier to noise ratio in dB.
C/N S2A C N 2 A # # . # #
CN2A: 0.00 to 63.75(dB) (DEC) "##.##"
Eg. 0x3F→63/4 = 15.75 (dB)
Satellite 2 Ensemble B carrier to noise ratio in dB.
C/N S2B C N 2 B # # . # #
CN2B: 0.00 to 63.75(dB) (DEC) "##.##"
Eg. 0x3F→63/4 = 15.75 (dB)
The averaged rate of uncorrectable words.
RSErrs Word R S W # # #
RS W : 0 to 100 (%) (DEC) "###"
The averaged symbol error rate of the RS decoder of
RSErrs Sat Symb R S S # # # the satellite channels.
RS S : 0 to 100 (%) (DEC) "###"
The averaged symbol error rate of the RS decoder of
RSErrs Terr
the terrestrial channels.
Symb R S T # # #
RS T : 0 to 100 (%) (DEC) "###"
INT16 value multiplied by 100. Values above 1000
Tuner Carrier (100000) may be represented as +99999 or -99999.
Frequency Offset T F * # # # # #
* : + / - , "#####"
Eg. 0 x FF86 → -123 x 100 = -12300
RSSI : 0 to -128 (dBm) (DEC)
Received Signal value with INT16 value multiplied by 1.
Strength R S S I * # # # * : + / - , "###"
Indication Eg. 0xFF86→-123
0x007B→+123
(No.WA185<Rev.001>)33/51
Display content Operation Display content Details
[Extended channels]
Receiver State:(hex) "##"
Bit0: TB[otdm], Bit1:S2B[otdm]
Receiver State O S T S X # #
Bit2: S1B[otdm], Bit3: Pipe[LckB]
Bit4: TA [otdm], Bit5: S2A[otdm]
Bit6: S1A[otdm], Bit7: Pipe[LckA]
[Extended channels]
OBER Sat 1A O B 1 A # # #
OBER S1A: 0 to 100 (DEC) "###"
[Extended channels]
OBER Sat 1B O B 1 B # # #
OBER S1B: 0 to 100 (DEC) "###"
[Extended channels]
OBER Sat 2A O B 2 A # # #
OBER S2A: 0 to 100 (DEC) "###"
[Extended channels]
OBER Sat 2B O B 2 B # # #
OBER S2B: 0 to 100 (DEC) "###"
[Extended channels]
OBER Terr A O B T A # # #
OBER S1A: 0 to 100 (DEC) "###"
[Extended channels]
OBER Terr B O B T B # # #
OBER S1B: 0 to 100 (DEC) "###"
Turbo Word Error Rate [Extended channels]
(Pipe 0A) O R 0 A # # #
OBS0A: 0 to 100 (%) "###"
Turbo Word Error Rate [Extended channels]
(Pipe 0B) O R 0 B # # #
OBS0B: 0 to 100 (%) "###"
[Module Version]
Module TypeID A/B/C M T X # # # # # #
Module TypeID (hex) "######"
[Module Version]
Module HWRev A/B/C ROTARY M H X # # # # # #
Module HW (hex) "######"
Up/Down
[Module Version]
ModSWRevMajor/Minor/Inc M S X # # # # # #
Module SW (hex) "######"
[Module Version]
SXIRevMajor/Minor/Inc S M I X # # # # # #
SXi (hex) "######"
[Module Version]
BBRevMajor/Minor/Inc B B X # # # # # #
BB (hex) "######"
[Module Version]
HDecRevMajor/Minor/Inc H D X # # # # # #
HDec (hex) "######"
[Module Version]
RFRevMajor/Minor/Inc R F X # # # # # #
RF (hex) "######"
Capability (title) C A P A B I L I T Y : Fixed string "Capability:"
[Module Version]
Capability (data) X # # # # # # # #
Capability (hex) "########"
[Module Version]
Subscription-Status S B S T X # #
Sub Status (hex) "##"
[Module Version]
ReasonCode R E A S O N X # #
Reason Code (hex) "##"
SuspendYear/Month/Day Fixed string "SUSPEND"
(title) S U S P E N D :
SuspendYear/Month/Day [Module Version]

(data) # # # - # # # - # # #
Suspend "###-###-###"
Clear Non-Volatile
Memory Mode C L E A R N V M
Init Lock Passcode I N I T C O D E
* [Extended Channels] items shall be omitted when the attached module does not have overlay capability.
(No.WA185<Rev.001>)34/51
4.6.4 Clear NVM Mode/ Init Code
Press [Rotary] knob Press [Rotary] knob

CLEAR NVM NO
Press [RETURN] key
OR
Turn [Rotary] knob
INIT CODE
YES
Press [Rotary] knob
CLEARING Blinking 500ms
OK
Press [RETURN] key
Display content
NO Y E S / < N O >
YES < Y E S > / N O
CLEARING C L E A R I N G
CLEARING OK C L E A R I N G O K
(No.WA185<Rev.001>)35/51
4.7 DC Offset Calibration Mode
4.7.2 Mode content
D . O F F C A L M D Display is released when an operation is executed.

C A L I B R S T A R T Note: Take about 4 sec to complete
Calibration Start DISP 0 = CH0, 1 = CH1, 2=CH2, 3=CH3
0 # # 1 # # 2 # # 3 # #
## = OK or NG
Calibration result 0 = CH0, 1 = CH1, 2=CH2, 3=CH3
value stored in DISP 0 # # 1 # # 2 # # 3 # # ## = OK or NG
memory

CH0 Score C 0 S C O R E # # # 0 to 999 (DEC) "###"
CH0 Delay C 0 D E L A Y # # # # 0 to 9999 (DEC) "####"
CH0 0 to 999 (DEC) "###"
WinThreshold C 0 W T H R E # # #
CH0 Offset C 0 O F S E T # # # 0 to 999 (DEC) "###"

CH1 0 to 999 (DEC) "###"
CH1 Offset ROTARY C 1 O F S E T # # # 0 to 999 (DEC) "###"

CH2 Score Up/Down C 2 S C O R E # # # 0 to 999 (DEC) "###"
CH2 0 to 999 (DEC) "###"

CH3 0 to 999 (DEC) "###"
(No.WA185<Rev.001>)36/51
4.8 DOP USB SET Mode
Pressing and holding [6] key, press [VOLUME] key for 7 seconds.
4.8.1 Mode Structure
Not display Opening indication for easy understanding of mode change.
Insert USB after enter to this mode.
UPDATE should be started after READING if there is a file for setting.
Display "NO FILE" if there is not a file for setting.
To check DOP Version toggle DISP key to Display "VER XXX" or "VER ---".
4.8.2 Mode content
System Microcomputer indicate following messages under this mode. And all key (except for EJECT) is canceled.
D O P S E T T I N G STANDBY condition of DOP setting update mode
R E A D I N G Under READING *Display with 2Hz blik
N O F I L E No DOP setting file
Under UPDATING after confirming that DOP setting is available *Display with 2Hz
U P D A T I N G
blink
V E R x x x Display DOP version with3 digits of number value. (After done DOP USB Update)
Display version is the default After market model or Not performed the DOP USB Up-
V E R - - -
date.
U P D A T E E R R O R Setting Fail
4.9 DOP Setup Mode
Pressing and holding [6 key, press [VOLUME] key for 7 seconds.
Default Mode: DOP USB SET
Turn [VOLUME] to change mode to DOP Setup Mode.
4.9.1 DOP Setup Mode Common Setting
Common settings for all car makers are as follows:
Demo: No demo animation

Remove all DEMO related items
Power on animation: Show carmaker's name

Only opening animation will show "Car maker's name"
4.9.2 EEPROM DOP Read Error Display
In the case of an EEPROM read error or EEPROM DOP read error, the unit will behave accordingly.
(1) No Power on animation
(2) No Demo animation
(3) Demo removed in setup menu
(4) Color settings set to default
(5) Serial number display replaced by "SN @@@@@@@@"
(No.WA185<Rev.001>)37/51
4.9.3 Mode content
Syscon shall display the following information after entering this mode. The operation shown below shall be workable.
D O P S E T U P The display is released when another operation is executed.
4.9.3.1 Single/ Dual Color Illumi Model/ Variable Color Illumi Model
Operation: Select Preset 1 to 6 keys for DOP settings / Press [RETURN] key to default settings.
Color changes only for Vario Color Illumi Models.
NO DEMO 1 COLOR: Same with default setting
Change to COLOR 14
CHEVROLET 2 C H E V O L E T
R=0; G=9; B=5
Change to COLOR 23
DAIHATSU 3 D A I H A T S U
R=9; G=2; B=0
Change to COLOR 23
FIAT 4 F I A T
R=9; G=2; B=0
Change to COLOR 14
FORD 5 F O R D
R=0; G=9; B=5
Change to COLOR 11
HYUNDAI 6 H Y U N D A I
R=0; G=5; B=9
Change to COLOR 24
ISUZU I S U Z U
R=9; G=1; B=0
Change to COLOR 24
KIA K I A
R=9; G=1; B=0
Change to COLOR 24
MAHINDRA DISP M A H I N D R A
R=9; G=1; B=0
Change to COLOR 23
MARUTI 1 M A R U T I
R=9; G=2; B=0
Change to COLOR 24
MITSUBISHI 2 M I T S U B I S H I
R=9; G=1; B=0
Change to COLOR 23
NISSAN 3 N I S S A N
R=9; G=2; B=0
Change to "White"
PEUGEOT 4 P E U G E O T
R=9; G=9; B=9
Change to COLOR 23
RENAULT 5 R E N A U L T
R=9; G=2; B=0
Change to COLOR 23
SUZUKI 6 S U Z U K I
R=9; G=2; B=0
Change to "White"
TATA T A T A
R=9; G=9; B=9
Change to COLOR 23
TOYOTA T O Y O T A
R=9; G=2; B=0
Change to "White"
VOLKSWAGEN DISP V O L K S W A G E N
R=9; G=9; B=9
Return to default Restore DEMO MODE related items
RETURN
settings R E S T O R E D
Change to VARIABLE SCAN
(No.WA185<Rev.001>)38/51
4.9.3.2 During Power On/ BU On/ ACC On transition
NO DEMO No opening display
CHEVROLET C H E V O L E T 1000ms
DAIHATSU D A I H A T S U 1000ms
FIAT F I A T 1000ms
FORD F O R D 1000ms
HYUNDAI H Y U N D A I 1000ms
ISUZU I S U Z U 1000ms
KIA K I A 1000ms
MAHINDRA M A H I N D R A 1000ms
Power On
MARUTI BU ON / M A R U T I 1000ms
ACC ON
MITSUBISHI M I T S U B I S H I 1000ms
NISSAN N I S S A N 1000ms
PEUGEOT P E U G E O T 1000ms
RENAULT R E N A U L T 1000ms
SUZUKI S U Z U K I 1000ms
TATA T A T A 1000ms
TOYOTA T O Y O T A 1000ms
VOLKSWAGEN V O L K S W A G E N 1000ms
Normal Display @ @ @ @ @ @ @ @ @ @ @ @ @ Return to normal display mode
(No.WA185<Rev.001>)39/51
4.10 HC Mecha Running Mode
Press and hold [SRC] key and [EJECT] key and reset.
The software specification for evaluating HC Mecha is described.
This mode is set for the general operation test and the endurance running test.
4.10.1 Mode Display Specification for Evaluation
Enter the
Run Test Display
mode R U N T E S T
Pressing Indicated “Running Mode”

and holding
Running Mode [RETURN] *****: Indicated number display
count display key and R M O D # * * * * *
insert the Repeated the eject.

disc
Tracking_gain ####: Indicated hex value
adjusted value T R - G A # # # #
display
Focus_gain
adjusted value F O - G A # # # #
display
Te_agc adjusted
value display T E A G C # # # #
Rf_agc adjusted
value display R F A G C # # # #
Te_balance
adjusted value T E B A L # # # #
display DISP
Focus_balance (Toggle the
adjusted value DISP) F O B A L # # # #
display
TNI offset adjusted
value display T N I O F # # # #
TPI offset adjusted

value display T P I O F # # # #
TPI_TNI offset
adjusted value T P T N O # # # #
display
TEO offset adjusted
value display T E - O F # # # #
FEO offset adjusted

value display F E - O F # # # #
Error Code Indicated “NO ERROR”

display when no DISP N O E R R O R
error
(No.WA185<Rev.001>)40/51
4.10.2 ERROR CODE for MODEL with FLM-HCI MECHA (Ver1.1)
DISPLAY SIGN ERROR Item Condition Details
Anomaly detection of SW state at LOADING.
LI-E LOADING TIME OVER In LOAD operating.
Or 5 sec TIME OVER from LOAD start.
Anomaly detection of SW state at EJECT.
EJ-E EJECT TIME OVER In EJECT operating.
Or 5 sec TIME OVER from EJECT start.
E-04 READ ERROR In RUNNING MODE operating TOC read error.
E-14 FOCUS ERROR In RUNNING MODE operating Focus Error. No complete Focus ON.
E-05 UNKNOWN DISC In RUNNING MODE operating No reflection.
E-20 NODISC ERROR In RUNNING MODE operating In case of DISC distinction.
E-21 DSP ACCESS ERROR In RUNNING MODE operating fails in the access to DSP.
E-22 LIM SW ERROR In RUNNING MODE operating Time over in case of that moves to an inner side.
AE-01 In RUNNING MODE operating Focus Gain Error
AE-02 In RUNNING MODE operating Tracking Gain Error
AE-03 In RUNNING MODE operating RF Gain Error
AE-04 AUTO ADJUSTMENT In RUNNING MODE operating Tracking Balance Error
AE-05 ERROR In RUNNING MODE operating Focus Balance Error
AE-06 In RUNNING MODE operating Focus Offset Error
AE-07 In RUNNING MODE operating Tracking Offset Error
AE-08 In RUNNING MODE operating RF Offset Error
4.11 Tuner Span Change Mode
Pressing and holding [1] key and [5] key, then Power On (During power off).
After selection of the setting item, the receiver should exit this mode and return to the display before entering this mode.
This setting will be stored in EEPROM.
4.11.2 Mode content
T U N E R S P A N Show for 1 second and then proceed to first item of mode content.

Change to 'US' Span type (also included in HD Ra-
A R E A N A
dio Models)
Tuner Span
VOLUME Change to 'SA' Span type (also included in HD Radio
Change Mode
+/- A R E A S A
Models)
(*1)
Change to 'EU' Span type (also included in HD Ra-
A R E A E U
dio Models)
A S I A Change to 'Asia' Span type.
Tuner Span Change to 'Tunisia' Span type.
VOLUME T U N I S I A
Change Mode
+/- Change to 'Australia' Span type.
(*2) A U S T R A L I A
O T H E R S Change to 'US' Span type.

Tuner Span Change to 'EU' Span type
VOLUME A R E A E U
Change Mode
+/- Change to 'Tunisia' Span type.
(*3) T U N I S I A
Release Mode VOLUME Depending on display pattern in normal mode.
*1: Only applicable for America ('K', eXcelon, 'R', 'JKLA') models
*2: Only applicable for Asia ( 'A', 'M', 'C', 'H' ) models
*3: Only applicable for Europe ('E', 'E2', 'M2') models
(No.WA185<Rev.001>)41/51
4.12 How to obtain BT MAC address and BT friendly Name from Kenwood Car Audio Set
(1) Turn On the Car Audio Set.
(2) Switch car audio set to Standby mode.
(3) Press button 2 and then button 6 together at the same time and wait for 7 seconds.
(4) Press button 1 till you get the BT MAC address from the display.
(5) Then press again the button 1 in order to get the BT friendly name from the display.
Remarks:
The obtained BT MAC address and BT friendly Name will be manual key into the NFC TagWriter by NXP apps and then write into
the NFC tag.
4.13 How to program BT MAC address into the NFC tag by mobile phone's apps
Install the NFC TagWriter by NXP apps inside a smart phone. The smart phone must consist NFC function.
Pre-condition:
Turn on the NFC function on the smart phone before open NFC TagWriter by NXP apps.
Condition 1:
Write the New BT MAC address inside the NFC tag (Manual key in the BT MAC address).
(1) Open the apps of "NFC TagWriter by NXP" and click "Write tags".
(2) In the following screen, choose the "New dataset".
(3) Then select "Bluetooth" at the "New dataset" screen.
(No.WA185<Rev.001>)42/51
(4) At the "Bluetooth" screen, click " Create new bluetooth".
(5) In the following screen, key in the BT friendly Name into the Device Name column, eg "kdc-U5**BT" and enter the Bluetooth
MAC address by manual key in, eg "001D864005c1" or "00:1D:86:40:05:c1".
Remarks:
There is no different between the small letter or capital letter for BT MAC address but for Device Name there is a different.
Then click " SAVE & WRITE".
(6) At the "Bluetooth" screen, select "Protection" checkbooks to open the "Protection" option and then select "Password protection"
option.
(7) In the following screen, select "New Password" checkbooks and then enter the word made up from 4 characters but for JVCK-
ENWOOD NFC tag, the password has been fixed as "1234".
Important notes:
Password must be inserted as "1234".
(8) Then press "Done" to exit the screen.
(No.WA185<Rev.001>)43/51
(9) Click "Write" when back to the "Bluetooth" screen.
(10) When the "Ready to store or share the selected content" screen prompt out, tap the tag to store the information (BT MAC address
here).
Remarks:
The definition of "Tap the tag" at here is "Move the smartphone with the NFC antenna part which is at the backside of the
smartphone to touch or as close as possible to the NFC tag and stay for few seconds until the NFC tag has been detected by
the smart phone.
(11) After detected the tag, the "Confirm overwrite" screen will prompt out and press the "TAP TO CONFIRM STORE" to confirm
writing instruction.
(12) After pressed the "TAP TO CONFIRM STORE", the "Ready to store or share the selected content" screen will prompt out and
tap the tag to store the BT MAC address inside the NFC tag.
(13) After successful to write the BT MAC address inside the tag, the Bluetooth result screen will prompt out and the new content of
the NFC tag will be displayed.
(14) Press the "Done" button to exit from the screen and back to the main menu of the NFC TagWriter by NXP.
(No.WA185<Rev.001>)44/51
4.14 How to change BT MAC address into a password protected NFC tag
Install the NFC TagWriter by NXP apps inside a smart phone. The smart phone must consist NFC function.
Pre-condition:
Turn on the NFC function on the smart phone before open NFC TagWriter by NXP apps.
Condition 1:
Write the New BT MAC address inside the NFC tag (Manual key in the BT MAC address).
(1) Open the apps of "NFC TagWriter by NXP" and click "Read tags".
(2) Then, the "Ready to read content and view results" screen prompt out, tap the tag to read the information (BT MAC address
here).
(3) In the following screen, choose the "EDIT DATASET".
(No.WA185<Rev.001>)45/51
(4) Then the "Bluetooth" screen will prompt out, initially, the old device name and old WLAN-MAC address will be displayed.
(5) Click the "Device Name" column to change device name with the new BT friendly Name by manual key in, eg "kdc-U5**BT".
Remarks:
If the car audio set is the same model as previous, no need to change the Device Name
After that, click the "WLAN_MAC" column to delete the old BT MAC address and then enter the new BT MAC address by manual
key in, eg "001D864005c1" or "00:1D:86:40:05:c1".
Remarks:
There is no different between the small letter or capital letter for BT MAC address but for Device Name there is a different.
Then click "SAVE & WRITE".
(6) In the following screen, the content to be saved will be displayed on the screen.
(7) At the "Bluetooth" screen, select "Protection" checkbooks to open the "Protection" option and then select "Password protection"
option.
(8) In the following screen, select "Current Password" checkbooks and then change the password "0000" to the fixed password
"1234".
(9) Then press "Done" to exit the screen.
(No.WA185<Rev.001>)46/51
(10) Click "Write" when back to the "Bluetooth" screen.
(11) When the "Ready to store or share the selected content" screen prompt out, tap the tag to store the information (BT MAC address
here).
Remarks:
the smart phone.
(12) After detected the tag, the "Confirm overwrite" screen will prompt out and press the "TAP TO CONFIRM STORE" to confirm
writing instruction.
(13) After pressed the "TAP TO CONFIRM STORE", the "Ready to store or share the selected content" screen will prompt out and
tap the tag to store the BT MAC address inside the NFC tag.
(14) After successful to change the BT MAC address inside the tag, the Bluetooth result screen will prompt out and the new content
as well as the previous content of the NFC tag will be displayed.
(15) Press the "Done" button to exit from the screen and back to the main menu of the NFC TagWriter by NXP.
(No.WA185<Rev.001>)47/51
4.15 How to set a new password on a already programmed tag
Note:
The below procedure are only applied if you've forgotten to set the password protection during writing the BT MAC address into the
NFC tag.
(1) In the main menu of NFC TagWriter by NXP, press the " Protect tags" button.
(2) In the following screen, press the "Password protection".
(3) To set the new password, select the "New Password” checkbooks and enter "1234" as the password for JVCKENWOOD car
audio's NFC tag.
(4) Press "Done" and tap the tag.
Remarks:
the smart phone. Different smartphone has different location for the NFC antenna part.
(5) In the following, the "Ready to password protect the content" screen will prompt out. Tap the tag to set the password to the tag.
(6) After the NFC tag has been detected, the "Confirm password protect" screen will prompt out, then press the "TAP TO CONFIRM
PASSWORD PROTECT" button.
(7) Repeat step 2.1.
(8) Finally, the result screen will prompt out and the message of "Content has been password protected" is shown if the NFC tag
has been successfully password protected.
(No.WA185<Rev.001>)48/51
4.16 User Manual for NFC function
Note:
After completed to store the BT MAC address inside the NFC tag, please confirm the NFC function (Simple Bluetooth Pairing) with
below procedure.
4.16.1 Simple Bluetooth Pairing (First time pairing to the audio unit)
(1) Turn on the NFC function of the smartphone.
(2) Move the smartphone with the NFC antenna part to touch to the volume knob of the audio unit and stay for few seconds.
(3) (i) After NFC has been activated, the below message will be prompt out:
- Bluetooth Pairing request
Confirm passkey is XXXX to pair with KDC-BT3*U.
(ii) Click "Accept" button on the smartphone screen to accept the pairing.
(iii) Press Volume Knob on the audio set to start pairing.
"Pairing OK" appears when pairing is completed and "BT"will light up when the connection is established.
(4) Once the pairing is completed, the smartphone will remain be registered in the unit even if you reset the unit.
[Note: Up to five devices can be registered (paired) in total.]
(5) In order to disconnect the bluetooth connection, move the smartphone with the NFC antenna part to touch to the volume knob
of the audio unit and stay for few seconds. Disconnect message will be prompt out on the smartphone screen.
4.16.2 Simple Bluetooth Pairing (For the registered Bluetooth device/ smart phone)
(1) Turn on the NFC function of the smartphone.
(2) Move the antenna part of the smartphone touch to the car audio volume knob and stay for few seconds.
(3) Once the NFC has been activated, the pairing is completed and "BT" will light up when the connection is established.
(4) In order to disconnect the bluetooth connection, move the smartphone with the NFC antenna part to touch to the volume knob
of the audio unit and stay for few seconds. Disconnect message will be prompt out on the smartphone screen.
(No.WA185<Rev.001>)49/51
4.17 DC Offset error description 4.17.5 Manipulate after detect DC Offset
4.17.1 DC Offset detection circuit design • If detected error 10 consecutive times, and 10th error occurred
• Purpose: in "Mis-connect detection period", judge as "Mis-connect".
To prevent breakdown, when occur DC offset between speak- • If detected error 10 consecutive times, and 10th error occurred
er output "+" and "-". in "Capacitor leak detection period", judge as "Capacitor leak ".
• Target: • If detected error 10 consecutive times, and 10th error occurred
Detect DC offset, then stop the Power Amp operation and shift in "Other detection period" and detected another 10 errors con-
to specified condition. secutively, then judge as "Other".
• If judge as "Mis-connect".
4.17.2 Possible causes of DC offset at speaker output lines - turn off speaker output.
(1) Mis-connection for Speaker output for example touch to car - display "MISWIRING", check wiring connection then reset.
body or battery line. - key access disable except button of Eject, Reset and service
(2) Current leak of coupling capacitor for Power IC input. mode
(3) Current leak of AC-GND capacitor for Power IC AC-GND. - record error in EEPROM "DC1 ERR"
(4) Capacitor shorted of above parts due to foreign object. - the product is able to be recovered by Reset button.
E-Vol • If judge as "Capacitor leak ".
Audio Pwr Amp
C-in - turn off speaker output.
In 1
C-in
- display "WIRING", check wiring connection then reset.
In 2 - key access disable except button of Eject, Reset and service
C-in
In 3 mode
C-in
In 4 - record error in EEPROM "DC2 #" (# means counter number)
- the product can be recovered by pressing the Reset button
C-ac1 C-ac2
before the capacitor leak error counter reach "DC2 4".
AcGnd
After that, only clear the counter back to "0" can recover the
C-tc product.
Sw5V
Win_TC
• If judge as "Other" (manipulation same as mis-connect)
R2
R1 Offset Detect
Win_In Out
C3
DC Error
R3
SECTION 5
R4
ADC In
Micon
TROUBLESHOOTING
5.1 How to cancel DC offset error
4.17.3 Type of checking Check to be sure the terminals of the speaker leads are covered
4.17.3.1 To detect DC Offset Error with insulating tape properly, then reset the product.
• Mis-connection If an error message does not disappear even after a reset, there
- Short any one speaker out line to GND or Vcc is a need for internal repair.
• Capacitor leak 5.2 How to clear DC offset error recorded in EEPROM
- Parallel 330kΩ to either any one of coupling cap or AC-GND
capacitor (to simulate current leakage of capacitor) Refer to “4.5 DC Error Information Mode”.
- Shorted either any one of coupling capacitor or AC-GND ca-
pacitor.
4.17.4 Detection Timing chart
2.0sec or more 1.5sec or more 50ms
or more
0.7sec or more
0.8sec 1.0sec
PWIC_STBY
PWIC_MUTE
AUD_MUTE
Missconnect Capacitor leak Other (miss detection etc.)

detection period detection period detection period
(No.WA185<Rev.001>)50/51
JVC KENWOOD Corporation
Automotive 2967-3, Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525, Japan
(No.WA185<Rev.001>)
Printed in Japan
VSE
SCHEMATIC DIAGRAMS
CD RECEIVER
KDC-BT565U KDC-X500 KDC-X5000BT
KMR-D765BT
(No.WA185<Rev.001>)1/16
PRECAUTIONS ON SCHEMATIC DIAGRAMS
Due to the improvement in performance, some part numbers shown in the circuit diagrams
may not agree with those indicated in the Parts List.
The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for
reference only.
Since the circuit diagrams are standard ones, the circuits and circuit constants may be
subject to change for improvement without any notice.
PRECAUTIONS ON PARTS LIST

The parts identified by the symbol are critical for safety. Whenever replacing these parts, be sure to
use specified ones to secure the safety.
The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No.
columns will not be supplied.
P.W. BOARD Ass'y will not be supplied, but those which are filled with the Parts No. in the Parts No.
columns will be supplied.
There are cases where the actual implemented parts in the sets and the service parts are different.
When ordering parts, make sure to refer to the Parts List.
DEVIATION TOLERANCE RANGE

DEVIATION TOLERANCE RANGE
F G J K M N R H Z P
+30% +50% +80% +100%
1% 2% 5% 10% 20% 30%
-10% -10% -20% -0%
(No.WA185<Rev.001>)2/16
BLOCK DIAGRAM (1/2) (SIGNAL BLOCK)
FL OUT FR OUT
CN220 CN990 IC301 CN103 J321 LINE OUT J600
SXM_PWR J470 BEEP RL OUT RR OUT
MIC PWIC_MUTE CONNECTOR

SXI PWIC_STBY REAR
JACK SXM_DA_SXM
DC_ERR ANT
QGA2001C1-02
FL+ RL+ USB
DC P.CORD JACK
FL- RL- POWER IC OFFSET
FR+ RR+ SXI_G
MIC_P
SXI_R LINE_MUTE
MIC_N FR- RR- D-0
SXI_L
MUTE D+0 OP_SWL_OUT
ACC EXT ANT OP_SWR_OUT
OP_FL_OUT
IC220 2 3 4
OP_RL_OUT
OP-AMP OP_FR_OUT
OP_RR_OUT
REMOTE ANT
DIMMER_LINE TEL_MUTE_LINE OE_REMOTE
MUTE_
DIMMER TEL_MUTE OE_REMOTE
CIRCUIT IC7
SDA_EET
IC901 SCL_EET
TUNER
ANT
LINE MUTE
2
E_MUTE
MUTE
RESET
FLAG_REG
MUTE I2S_SD
I2S_BCK
EXT
1 I2S_WS
ACC
6
IC101
REGULATOR
SELECTOR
MRC_DATA_MRC
FLAG_REG
MRC_DB_UART1_TX
SCL_REG CN37
SDA_REG
MRC_DATA_SYS
IC102 MRC_DB_UART1_RX IC164 +IN2

IC163
OP-AMP OP-AMP OP-AMP OP_SWL_OUT

OP_SWR_OUT
JTAG_TRSTN
JTAG_TDI
JTAG_TMS
AUX_SXM_L JTAG_TCK M_SWL_OUT
AUX_SXM_R JTAG_TDO M_SWR_OUT
RESET TEST POINTS
(SW DEBUGGER) +IN2
IC162
Q880
OP_FL_OUT
OP-AMP OP_RL_OUT
HOLD IC821
OE_REMOTE
CLK
M_FL_OUT
TEL_MUTE
SXM_R
DO
SXM_L
PWR_EN
TU_I2S_FS M_RL_OUT
DC_ERR
RESET
CS FLASH IC
DIM_IN
FREQ_SEL TU_I2S_BCLK
DI
TU_I2S_RX
WP +IN2 IC161
CLK
3 SDA_EET OP_FR_OUT
IC862 SCL_EET OP-AMP OP_RR_OUT
MIC_P
IC701
DCDC MIC_N
OFFSET
SQI_SIO3
SQI_SCK
MUTE SQI_CEON IC822 M_FR_OUT
DO M_RR_OUT
SQI_SI00
SQI_SI01 CS
SPI_DATA_SPI
IC863 SQI_SIO2 CLK FLASH IC
SPI_EN DI
SCK_FB
SPI_CLK
DCDC 8
SPI_DATA_MICON
BEEP MICON M_SWL_OUT
PWIC_MUTE
6 M_SWR_OUT
PWIC_STBY
M_FL_OUT
M_DA_SXM ACCORDO2 M_RL_OUT
M_FR_OUT
M_RR_OUT
SXM_DA_SXM
CD MECHA FC2-3A
SXM_PWR
Q865
PON_USB1 FOO
TRO Vref
CD_DSP_SW IC941 FMO VT1
IC540 LDO_3.3V
CN502 (26PIN)
PON_USB0 DMO VT2
CN1 (26PIN)
3
HSS STAT BCLK VF1 CD_MD
NRST LRCK VF2 LD
VF2
MDATA M_SRDATA_CD
MRD BLKCK SW1 FFC
DRST CD_SRDATA_M SW2 Cable
PSW
DRV_MUTE
SCL_IPOD
DRV_LO_EJ
IC411 SDA_IPOD
DRV_CNT
IPOD IC MCLK
IC1303
BT_UART0_CTS
BT_SYS_DATA
RGB_CLK BT_UART0_RTS
LCD_DATOUT BT_BT_DATA
PON_PANEL LCD_DATIN BT_RST
LCD_CLK
Q920 LCD_CE BT HCI
REMO
PANEL3.3V ENC1
F_AUXL
BT_I2S0_RX
D+1 ENC2 *Steering REMO1
BT_I2S0_TX
D-1 *PAN_DET(1DIN) F_AUXR *Steering REMO2
BT_I2S0_FS
*RESET(2DIN) F_AUXG
BT_I2S0_BCLK
CN701 CN400 IC831

PANEL CONNECTOR RESET IC
No.WA185 created date:2015-11-25

(No.WA185<Rev.001>)3/16
BLOCK DIAGRAM (2/2) (SUPPLY BLOCK)
CN990 J470 J220 LINE OUT J600
IC301 CN103
CONNECTOR
L990 SXI REAR ANT
DC P.CORD MIC POWER IC USB
MEM14.4V JACK
17 9 JACK
J321
D990 14.4V
VCC1 7 VCC2 21
2 3 1 4
V6IN
GND
ACC
ANT
EXT
VDD3.3V
IC601
IC470 Q470 Q471
MUTE_ DIMMER TEL_MUTE TUNER
IC901 GND
CIRUIT VDD
AtomicIC 2
1 1 1
9 VDDA_RF
ANT
TO MARINE REMOTE VDDA_IFADC
2 For SXI
TU3.3V
EXT 15
1 0.45A
1 TEST POINTS
ACC
AU9V
6 4
0.25A
VCC1
8
SW JIG
CD8V
1.3A 5 DEBUGGER
D902
REGULATOR IC164
IC880
GND2
ILM12V
DCDC PWR EN 6
OP-AMP
4
0.3A 3
VCC2
7
D903 VDD3.3V
0.35A 11
IC930
V6IN VDD3.3V
1 5
SW3.3V IC163
13
LDO_3.3V
D930 8 OP-AMP 5
GND2
VDD3.3V
IC162
IC851
IC863 DCDC5.2V IC141 LDO_1.2V 8
8
OP-AMP 5
VCC IC821
2 REAR DCDC 3
HSS
IC701 FLASH
D863 (Program stored)
VDD_IO_ON3.3V VDD1.2V
IC161
IC862 DCDC5.2V IC411 8 OP-AMP 5

VCC
2 FRONT DCDC 3
8
D862 IPOD
8
GND2 IC822
MICON IC220 CN220
VDD_IO3.3V
ACCORDO2 FLASH OP-AMP MIC JACK
IC102 VIN
(IAP1)
IC841
5
CD MECHA FC2-3A
OP-AMP
EEPROM 8
IC101 VIN
OP-AMP 5
CN1 (26PIN)
CN39 (26PIN)
V6IN
IC941 CD3.3V
1 5 FFC
LDO_3.3V Cable
CD8V
VDD_PADG
OUT
IC540 DCDC5.2V
9 IC1302
6 1
HSS IN
20
Q920 VDD_3V3
BT MODULE
PANEL3.3V SW
2 8
IC831 IC841
3 15 16
CN701
RESET IC EEPROM
PANEL CONNECTOR

(No.WA185<Rev.001>)4/16
MAIN PWB ASSY(1/2) (XK1-050x-xx)
ANT
? R693 TL89
C621 (TUL)
1u
J600
*FRONT-R
*FRONT-L
C620
QNB0356-001 1u
*REAR-R
*REAR-L
/REAR-R
/REAR-L
(TUR)
SUB-R
? R692
SUB-L
NAF0024-001X
R691
R690
TL88
0
VA600
? VA602
JCV8034
V
!
IC301
PWGND1
PWGND2
PWGND3
PWGND4
ACGND
? VA601
MUTE
VCC1
VCC2
STBY
TAB1
TAB2
V
OFFDET
SVR
C1600
IN2
IN4
OUT2+
OUT1+
OUT3+
OUT4+
QAX0969-001Z R611 TL219
OUT2-
OUT1-
OUT3-
OUT4-
SGND
*J220
0.1u 9.216MHz 100 C1604 *J321 E1B-0013-00
8
*J470
IN1
IN3
CD
1
3.3V
1.5V
1.5V
3.3V
3.0V
? D2003
0.1u
? D2004
X600 T1 TL98 QNZ0907-001 1 3 5 7 9 11 13 15 17 19 21 23 25 27
0V
0V
0V
C1603
0V
?R2024 (SL) T1 T3
? C1004
TL56 0.1u 2 4 6 8 10 12 14 16 18 20 22 24 26
XTAL_IN 32
VSS 31
DAC_L 30
DAC_R 29
GPIO_0 28
GPIO_1 27
GPIO_2 26
SCL 25
GND1 (SIG) ?R253 2 TL211 T2 1 2 3 T6
0.1u T2 TL100 TL212
14.2V
14.2V
R2073
C619 TL210 TL207 TL208 TL206 TL236 (SR)
3.3V
7.0V
3.3V
7.0V
7.0V
7.0V
7.0V
6.8V
6.9V
6.9V
6.9V
7.0V
7.0V
7.0V
7.0V
3.3V
7.0V
3.3V
0
TL209 *R2023 T4 T7
0V
0V
0V
0V
0V
0V
*C2017 0 TL99 4 5 6 7
T5 T9
? R1000
C618 ? C340 ? C350 ? C320 ? C330 ? C260 ? C250 4700p (SG)
0.1u R601 TL218
F1
? C305
? C306
3.0V 100 T8 8 9 10 T10
!
3.3V
*D472
*D474
*D471
TL213
*D473
17 18 19 20 21 22 23 24
180
RSB6.8SM-X
RSB6.8SM-X
RSB6.8SM-X
RSB6.8SM-X
1
VDDA_IFADC SDA
*R476
180
C312
*R350
*R320
*R330
22k
R250
180
180
180
0V C273
DZ2J068M
1.0u
R260
C617 0V
180
? C303
DZ2J068M
*R340
11 12
2
VSSA_IFADC ! VSSD_IO SW3V3
*D476
*D475
L607 0.22u C603
C304
47u
2.6V 3.3V *R341 *R351 *R321 *R331 R261 R251 VDD SW3V3 TL61
3
VBGP IC601 VDDD 0.1u 1u
(AC)
1p
4.7
C615 0.15u 1.2V 0V 1. VOLTAGES ARE DC-MEASURED WITH A DIGITAL VOLT METER
C611
10
10
C612 TEF6657HN-X 22k 22k 22k 22k 22k 22k
0.12u
4
33p C614 L605 FM_CAP VSSD
L606
0.01u WITHOUT INPUT SIGNAL
? C307
? C308
22p 0.22u C616 1.2V 0V ! Parts are safety assurance parts.
*R469
*R468
*R467
CONDITION---FM MODE. AM MODE ( )CD MODE.
5
FM_IN_M I.C.
3 1/4W
1000p 0V
R303
?R305
1.2V
3.3V
*R471
6
FM_IN_P I2S_SD_1
100
*R474
*R472
UNLESS OTHERWISE SPECIFIED. When replacing those parts make
100k
*R477
0V GND3
3.2V
3.2V
3.3V
220
100
0V
7
VDDA_RF I2S_BCK GND5
4.7k
*R473
C609 0V ALL RESISTORS ARE 1/10W 5% METAL GLAZE RESISTOR.
0V
100k
*C474
2.2u
*C473
10u
*C475
2.2u
R270
10 AM_LNA_CAP
ALL CAPACITORS ARE 50V OR 25V CERAMIC CAPACITOR. sure to use the specified one.
8
R605 0.1u VSSA_RF I2S_WS 3 2 1
? C309
? C310
14 DR_Q_DATA
C610 C1601 Q270 5.1V
15 DR_I_DATA
4.7
RR+
FR+
RL+
RR-
FL+
ALL RESISTANCE VALUES ARE IN OHM.
FR-
12p LTA024EEB-X
RL-
GND
IN_A
IN_B
*R343
*R353
*R323
*R333
16 I2S_SD_0
FL-
0V 0V 0V 0V 0V 0V
AM_IN_P
R262
R252
C2012 D271
13 DR_BCK
LTC014EEBFS8 *Q471
330
330
330
330
330
330
GND
12 DR_WS
3.3V 3. COMPONENTS WITH ? IN FRONT INDICATE NOT USE
? R478
0.1u
11 DR_BL
0.1u 0.6V 0.6V 0.6V 0.6V 0.6V 0.6V 0V BAW56-TP-X *Q470 5.1V
3.3V
LTC043TEB-X
*IC470
C602 3.3V
0
L604 L603 C472
OUT_Y
0.1u 3.3V C311
C316
0.22u
C317
0.22u
C319
0.22u
C318
0.22u
R272
33
VCC
10u 0V 4.7u
? R2022
0V 0V 30k
*R2021
*R2020
3.3V
9
0V 0V 0V 0V
R304
4.7k
4.7k
4.7k
4.7k
4.7k
4.7k
6.3V
*C341
10u
*C351
10u
*C321
10u
*C331
10u
C261
10u
C251
10u
C1020
47k
820
R264
R602 0.1u
R302
22k
*R322
*R342
*R352
*R332
1.0u
R254
R273
*R475
C608 0.85V R600 C601 *Q370 *Q380 Q240 0V
Q271
1V
0V
0V
0V
0V
0V
0V
C607 82 4 5 0V
10
Q273
1000p IMX9 IMX9 IMX9
0.1u
LTA024EEB-X
LSAR523UBFS8
? C1021
Q272
DA2J101
3.2V
3.2V
1k 10u LTC024EEB-X
D273
L601 C605
R271
R158
R159
R200
R201
L602
1p
0.47u
330
4.7u 1000p TL62 C1602
R2042
(SWRO)
30k
0
L600
(SWLO)
R1070
(RRO)
4.7u
(DIST)
(FRO)
(RLO)
R604
(FLO)
1k
TL77
TL75
TL76
TL74
TL79
TL78
C606
R603
1M
3.3k
R680
1M
9p C604 0.1u ? R1001 ?R688
R167
R152
R177
R154
1500p TU3V3
? D2007
R2082
12
12
12
12
0
20 *R168
20 *R192
20 *R155
20 *R153
20 R157
20 R156
? C624
? C1050 ? R1050
OP_SWR_OUT
OP_SWL_OUT
SXM_R/MIC_N
SXM_G/MIC_P
SXM_RXD_M
OP_RR_OUT
SXM_TXD_M
OP_RR_OUT
OP_FR_OUT
OP_FR_OUT
PWIC_MUTE
OP_RL_OUT
OP_RL_OUT
OP_FL_OUT
OP_FL_OUT
LINE_MUTE
LINE_MUTE
GND2
REG_FLAG
RESET
PWIC_STB
SXM_PWR
DC_ERR2
P_MUTE
P_MUTE
SDA_TU
OFFSET
SCL_TU
SXM_L
MUTE
BEEP
TL229 *CN481
TU.R
TU.L
C2120 *C2085 QGA2001F1-06
VREF6V 0.01u 0.01u
SW3V3 FLASH *Q487 6 GND
MUTE
SW1V2(1V2)
0.01u
AUD_SEL
*C480
LDO_1.2V OP_RR_OUT *Q484 TL233
PWIC_MUTE
ENC2
ENC1
DC_ERR2
JATG_TRSTN
NOISE_CTRL
PON_USB1
PWIC_STB
JTAG_TMS
JTAG_TCK
JTAG_TDO
JTAG_TDI
OFFSET
TL26 LTC044EUBFS8 *R481 5 D-(B)
*R162 RSR015P06 TL232
R160 *C160 *R165
R2072
4.7k
BD00IA5WEFJ SW3V3 (DO)
D
C2112 4700p (WP) TL50 3.3 4 D+(A)
TL46
*C163
0 SQI_SIO2 *R482 TL231
*R163
3 REQ
0.1u
(CS)
NAF0029-002X
IC851 *C162 SQI_SIO1 *R492
M_RR_OUT *C161 R820
*VA480
R850
*R161
12k
0.5%
1.2V R2005 C2111 4700p TL48 PON_MRC 3.3
VCC 3.2V 47k SQI_CEON 1k 2 VDD
DZ2J062M
DZ2J062M
100
*R491
C2093
8
VDD *C164
330k
3.3k
*R494
*R495
*D482
VO R2055
*C481
VDD
100
10
*R480
*D481
*R493
0.8V 2.2 10u 1 GND
TL230
NC_7 SW3V3 10k
*D480
2
7
1/4W *R164
*R166
FB C2091 R2056 *Q483
3.3V
3.3V
3.3V
1000p
0V
*C484
DZ2J051M
LSAR523UBFS8
0V
NC_6 330p 2.5V
? R2091
? R2092
4.3k
LSCR523UBFS8
3
6
*R497
6V
6V
6V
GND_3 0V
4.7u C851
*Q485
0V
3.2V
-9
EN Q2010 4 3 2 1 LTC043ZUB-X
C2107
C2106
4
5
? R2036
C2067
? C2068
RIGHT
LTC043TEB-X
100p
100k
NC_4 4 3 2 1 3.3k
47k
*R483
*R485
*R486
1.6V
? C850
R851
24k
GND
WP
DO
CS
15k
0.5%
? R2035
100k
*R488
4700p
*Q482
VEE
+IN1
-IN1
OUT1
MX25L6433F2I8
470p
LB73G0BK-006
?R2011 EEPROM
LSCR523UBFS8
0V
IC821
9
0V 0V 0V
47k
NJM8065V
5V
0V
0.6V *C483
L821
1.1V
3.6V
470p
470p
?R2010
? C822
HOLD
SCLK
0.1u
IC161
NOISE_CTRL_R
VCC
0.6V
*Q480
*R496
OUT2
?R2013 SW3V3
LSCR523UBFS8
47k
+IN2
IC841
VCC
DI
-IN2
C821
C820
?R2012 SW3V3 AUD12V 8 7 6 5
!
?R687
?R686
?R681
0.01u
BR24T02FJ-W-X 0V
*C485
*R487
SN65HVD3082ED
2.2k
*Q481
VCC
B
A
GND
2.2k
5 6 7 8 3.3V 0V 0V
22k
5 6 7 8 *Q486 3 2 1
*R484
3.2V
3.2V
3.2V
R840 IC831 FIELD TEST 1
*C482
? R689
TL51
0V
0V
0V
*IC481
TL115
3.3V
3.3V
3.3V
BU4228F-W
2.2k
100
12V
Q2011
6V
6V
6V
SDA_TU 3.0V 0V
1u
(HOLD)
R402
2.2k
GND
IN_A
IN_B
BT_DATA_BT
TC7SH08FU-X
LTC043TEB-X
3.9k
3.9k
SDA
100
GND
4
100 ? R822 SQI_SIO3
R2034
24 23 22 21 20 19 18 17 16 R841
? R816
? R818
6800p *IC482
BT_DATA_SYS SCL_TU 3.0V 0V 0V R830
*R817
3.2V
C177
? R821 SQI_SCK
? C178
*C170
10u
SCL
LB73H0AY-004
L811
A2
3
VOUT *C166
? R812
R2057
4.3k
GND24
NC_23
NC_22
NC_21
GND20
UART_TX
UART_RX
UART_RTS
UART_CTS
C2044 C2042
4
BT_UART0_CTS 100 TL116 C2092
QSW0648-001Z
OUT_Y
RE
DE
TL55
0V 0V GND TL49 TL47
(TM)
R685
R684
R682
R683
1.7V S830 100p 100p 330p SQI_SIO0 MRC_DATA_EN
D
FIELD TEST 2
*R2007
WP A1 (CLK) (DI)
2
BT_UART0_RTS CT *R489
VCC
*R148
*R490
3
*R172
TL121
3.3V 0V VDD R823 SQI_FB 33k 18k 1 2 3 4
*C486
MRC_REQ_SYS LTC043ZUB-X
3.2V
VCC A0 *C169
470p
C402
0.1u
R2058 C2114 VDD
C2038
100p
*R170 SW3V3
0.047u
10k 4700p 47 MRC_DATA_MRC
2.5V
2.5V
3.2V
1.1V
C840
L831 4 5
C2033
R842
0.01
GND_15 15 0V
*C146
NQR0713-001X
C831
M_FR_OUT
*R169
100
SPI_DATA_SPI
BT-MODULE
C830
MRC_DATA_SYS
1u
RESET
0v
0v
0v
0v
0v
0v
3.3v
3.3v
3.3v
3.3v
3.3v
3.3v
3.3v
VDD_1V8 14 1.8V *C165 *R146
? R807
R147 MRC_REQ_MRC
TL44 TL69 TL68
W19
C2056 R828
C2073
100p
I2C_WP 13 0V *R171 (SPIEN) D+0
W18
W17
W16
W15
W14
NC W13
NC W12
NC W11
NC W10
W9
W8
W7
W6
W5
W4
W3
W2
GND W1
PWIC_MUTE V19
NC V18
NC V17
NC V16
NC V15
NC V14
NC V13
NC V12
NC V11
NC V10
V9
V8
V7
V6
V5
V4
V3
V2
V1
MUTE U19
DC_ERR2 U18
NC U17
NC U16
NC U15
NC U14
NC U13
NC U12
NC U11
NC U10
U9
U8
U7
U6
U5
U4
U3
U2
U1
NOISE_CTRL T19
PON_USB1 T18
PULL_LO T17
PWIC_STBY T16
NC T15
NC T14
NC T13
NC T12
NC T11
NC T10
T9
T8
T7
T6
T5
T4
T3
T2
T1
OFFSET R19
NC R18
NC R17
NC R16
NC R15
NC R14
NC R13
NC R12
R11
R10
R9
R8
R7
R6
R5
C2034 RESET (RST) 0 470p 10k R824 (SPIDO)
0.01u 3.3v ? R810 LCD_CLK OP_FR_OUT VREF6V 47k SPI_EN D-0
I2C_SCL 12 2.9V A1 LCD_CLK R4
SPI_MISO/PCM_OUT
TL221
SPI_CS/PCM_SYNC
NC
SPI_CLK/PCM_CLK
0v R809
? C2079
*C2078
4700p
1k (5VR)
NC
NC
NC
NC
NC
DAB_COM_ON
FIELD_TEST2
FIELD_TEST1
NC
NC
NC
NC
NC
NC
RGB_CLK
ENC2
ENC1
NC
NC
NC
NC
NC
NC
NC
JTAG_TRSTn
NC
NC
NC
NC
NC
NC
JTAG_TMS
JTAG_TCK
JTAG_TDO
JTAG_TDI
SPI_MOSI/PCM_IN
SXM_RXD_M LCD_TXD_LCD
3.3V
3.3V
3.3V
I2C_SDA 11 2.9V A2 SXM_TXD LCD_TXD_LCD R3 OP_FL_OUT TL35
0V
C2109 C2110 *IC141 *CN141
3.3v R742 100 ? R145
SPI_PCM_SEL
SW3V3 IPOD_SDA LCD_DATA_SYS *R174 QGA2001C1-05
R2070
4.7k
GND_10 10 0V BD2242G-G
1u
A3 IPOD_SDA LCD_DATA_SYS R2
W25Q16DVSSIG -9
*IC1303
4 3 2 1
VDD_PADS
C2032 IPOD_SCL 470p 100p 3.3v R806 1k LCD_CE *C173 *R150 GND1 5 USB1
100
100
R149 TL104
VDD_3V3
A4 IPOD_SCL LCD_CE R1
LB73G0BK-006
GND
WP
DO
CS
0.01u 5.1V OUT 5.1V (D-R)
1k
GND_1
RESET
6
MRC_REQ_SYS R805 4 D-0
*C174
R11: NC
R10: NC
R9 : NC
R8 : NC
R7 : NC
R6 : NC
R5 : NC
*R175
0 C2098
L830
A5 MRC_REQ_SYS NC P19 IN
IC822
*C172 *C141 0V 0V
C1300
R702 2.2k M_FL_OUT *C171 *R173 10u ILIM
!
C2070
GND6
5
SDA_TU 3.3V 3 D+0
3.3k
1u
*R1303
*R1302
GND
12k
A6 SDA_TU NC P18
HOLD
R704 R703 *C175 *R176 PON_USB1 3.2V OC 3.2V TL103
VCC
2.2k 100 ? R720
CLK
R2059
4
1 2 3 4 5 6 7 8 9 SCL_TU 3.3V EN *L140 (D+R) 2 GND
A7 SCL_TU NC P17
DI
? R142
10k
*R143
2.2k
*R141
*R151
R705 100 (RXM) R2008 C2096 L7K-0030-00
*C143
*C144
0V
0V
VDD 3.3V 1 GND
*C145
R2061 330p
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
3.2V
TL54 A8 PCB_TEST_MODE RX / SD_CLK NC P16 4.3k 5 6 7 8
W16: PCB_TEST_MODE
6V
6V
6V
0V
100 0v 3.3V ? C825 *R144
0V
*VA141
*VA140
A9 SD CMD NC P15 Q2020
V
TL120
3.3V
3.3V
SDA_TU ? C739 LTC043TEB-X 4 3 2 1 0
F0K-0010-00
L2010 R827 10k C824 100p
F0K-0010-00
A10 NC NC P14
5.6k
SCL_TU
LEFT
R1300
470p
27p
27p
?R735 NQR0713-001X
VEE
+IN1
-IN1
OUT1
? R2039 SW2 3.3V *C142
? C2006 A11 SW2 NC P13 ? R825 SPI_CLK
W15: AUD_SEL
? R1304 10u
NJM8065V
0v TL71
? R708
C2066
C742
100p
C2040
A12 PULL_DOWN NC P12 ? R826
10u
10p
1u
SPI_DATA_MICON
IC162
0.01u
(SPICLK)
C2010
C2011
R709 SW1V2 NOISE_CTRL_L

0.01u
4.7k
W19: GND
OUT2
3.3V
+IN2
VCC
A13 PULL_HI_VDD NC P11
-IN2
W18: NC
W17: NC
W14: NC
R710 47k (SPIDI)
C1301
R2014 ? R1305 47k 3.3V AUD12V TL70 *C2082

A14 PULL_HI_VDD NC P10 PWR_EN 0.01u GND5
R711 VDD
10k BT_RST 47k 3.3V 5 6 7 8
C2035
A15 PULL_HI_VDD NC P9 LTC043EUBFS8
6V
10p
C741
100p
C708
1u
R880 2.2k
12V
R714 ?R738 Q2021
6V
6V
BT_I2S0_TX REG_FLAG R712 47k 3.3V C713 1u Q880 R878 10k
47k LTC043TEB-X
A16 REG_FLAG NC P8
BT_I2S0_BCLK LCD_TXD_LCD
? R877
PAN_DET 0v C740 *C184
3.2V
? C168
10u
2V
A17 PAN_DET NC P7 C2097
C167
BT_I2S0_RX 4700p R2062
R713 330p
*R180
BT_I2S0_FS MRC_REQ_MRC 100 C750 4.3k FREQ_SEL ? C879
A18 MRC_REQ_MRC NC P6 *C176 *R197 5 4
? R701 4.7u
? C870
*C179
R870
10k
VCC
OUT_Y
A19 GND NC P5 C738 4700p R2060 *R887
TL220 *R182 PON_USB1
TC7SH08FU-X
10k *R2086
SXM_TXD_M ?R717 0v C2039 *R886 5.1k 0
B1 SXM_RXD DAB_TU_RST P4
*R181
*C183
(REMAP1) M_RL_OUT OVP1 ? D863 2.2k
IC702
REMAP1 0v *R802 4700p
CD3V3 TL52 B2 47k
NQR0593-001X REMAP1 DAB_REQ_DAB P3 R179 *C180 *R178 ?F4
2.2k
IN_B
IN_A
GND
CN502 MRC_DB_UART1_RX R718 L2004 TL125 3.3V 3.3v *R803 REMO
B3 MRC_DATA_MRC REMO P2 (DCR) 15p
QGF1040F1-26 MRC_DB_UART1_TX 4.7k TL124 3.3V R801 C737 7p 0 TL32 *C894
L2003 B4 MRC_DATA_SYS (PULL_LO) LCD_INH P1 *R183 *IC863 TL108
T26 26 2.2M 1 2 3
*L866
OP_RL_OUT (FBR1)
4.7u
L7J-0092-00
C2043 BEEP ?R719 NQR0593-001X 0v 0.6v MP9943AGQ
2V
0V
B5 BEEP EXTAL N19 TL107
68k
LTC043EUBFS8
*R885
T25 25 R800
3.1V
R808 2.2k (FBR)
R799
*R879
0.1u
RESET 3.3V 0.2v 0 24MHz
B6 RESET XTAL N18 39k
1k *R888
T24 24 0.01u
1M
0.8V
10u
R2033 10k OP_SWL_OUT VREF6V PWR_EN PG
1
CD_DSP_SW 0v
? R874
? C701
*C889 *C888 *L865

10u
B7 CD_DSP_SW NC N17 FB
*C884
T23 23
*Q865
? R2075 R752 X701 R189 *C185 *R185 C2041 LCD_DATA_LCD 14.0V IN 4.8V
2.2k
2
100 3.3v R798 C736 VCC *C892
T22 22 B8 TEST_POINT PON_USB0 N16 100p
150u
5.2V 1.6V 0.22u
*C885
*C887
3.3V SW
R2071
(TXM)
4.7k
3
3.3v C735 0
*C190
4700p *R186
*C891 *C890
*R884
B9 PCB_TEST_MODE_TX PLL_VREG3V3 N15 EN/SYNC *R881
0.1u 0.1u
*R882
T21 21 TL53 PON_USB0 *C181*R190 0V GND 9.8V
7p
*R187
4
R2009 100 M_SWL_OUT
10u
39k
18k
T20 20 STAT B10 NC NC N14 SW3V3 BST 20
*R188 C2103
*C195
R2069
NRST R2063
470
T19 19 B11 NC 1.2V N13 10k *C893
10u
10u C2088 0.22u
6V *R191
MDATA B12 NC 1.2V N12 R2066 C2101 82k
T18 18 4.3k 330p *C895 0.1u
MLD DRV_LO/EJ 0v *C182 10u
T17 17 B13 DRV_LO/EJ 1.2V N11 Q2031 Q2001
? R2068
SUB WOOFER
R725 100 LTC043TEB-X
0V
6V
6V
MCLK 3.3V LTA043EEBFS8
T16 16 B14 PULL_HI_VDD 1.2V N10
D2005
R869
!
1k
BLKCK PWR_EN R726 10k C714 0.01u C756 R756 100 3.3V 4 3 2 1 DA2J101
T15 15 B15 M3_PWR_EN VDD N9 5.1k
D862 F3
VEE
+IN1
-IN1
OUT1
DRV_CNT 1u R734 100 0v R868
NJM8065V
T14 14 BCLK B16 DRV_CNT VDD N8 NOISE_CTRL_L OVP
IC163
NOISE_CTRL_R
? R2053
2.8v DB22306 2.5 A 32V
To CD MECHA PWB ASSY T13 13 CD_SRDATA_CD C2095 B17 10nF//10uF VDD N7 NOISE_CTRL_L
NOISE_CTRL_R
10
OUT2
M_RL_OUT 4.7u TL81 C883
+IN2
_0.5%
SW1 C702 C703 0.01u
VCC
10u B18 SP_RL 1.2V N6
-IN2
T12 12 15p
R2040
M_SWR_OUT (RL) AUD12V IC862 TL106
TL85 B19 SW_R 1.2V N5 D2006
(X32-6690-00)
L864
T11 11 C2087 MP9943AGQ (FBF1)
4.7u
R876
NQR0593-001X
68k
C2099 (SWR) R2067 DA2J101
0.01u
0.5%
SW2 SXM_PWR 4.7u L2002 3.3V 5 6 7 8 10u TL105
T10 10 C1 SXM_PWR DAB_DATA_SYS N4 Q2030 10k R871
150u
(FBF)
12V
6V
6V
6V
LTC043TEB-X
10u
LRCK SQI_SIO3 ? R727 L825 3.3V PG 0.8V 39k
5p
C2 SQI_SIO3 DAB_DATA_DAB N3
1
T9 NOISE_CTRL
C2080
L863
CN1
9 FB
10u
REMAP0 LB73H0CT-002 3.3V 14.0V 4.8V
10u
PSW R889 *C196 IN
? C188
C3 REMAP0 DAB_REQ_SYS N2
C187
R2054
2
T8 8 TL127 3.3k R2065 C2102 VCC C881
C2083
C873
C868
MRC_DATA_EN 330p *C186 0
C2116
0.01u
5.2V 1.6V 0.22u
18k
DA2J101
DRV_CNT 4.3k SW
D2008
C4 MRC_DATA_EN DAB_COM_CLK N1
*R240
R797
3
5p
T7
0.5%
7 *R196 Q2002 EN/SYNC R872
R875
39k
C2030
C876
C878
PON_MRC 3.3V 1.5v 2.2k FREQ_SEL
R873
DRV_LO/EJ C5 PON_MRC FREQ_SEL M19 *C189 LTC043TEB-X 0V GND 9.8V
0.1u
10u
4
T6 6 R730 R2064 BST
_0.5%
1/16W
DRV_MUTE 2.2k 1.2v 10k 20
T5 R729 3.3k C6 NC ! 3K_1% M18
*R193
5 R796 3k
*C198
5p
CD7V REG_SCL 3.3V M_SWR_OUT *R194 C871
C2029
L2001 C7 REG_SCL VREG_BYPASS M17 ? C734
T4 4 R239 C880 0.22u
LB73H0CT-002 TL238 2.5v C733 4.7u *R199
T3 L704 C8 SD_DAT PLL_VDD2.5V M16 GND5 0.1u
T2
3
2
C2077 BCLK
NQR0713-001X ? R732
R731 100
? C757
3.3V
C9
C10 NC
BCLK IC701 GND M15
OP_SWR_OUT
0 *C197
*R195
T1 1u VDD M14 C2105 100p

1 MDATA L702 0v TL31
? CN702 R795 C11 MDATA VDD M13 BD2242G-G
USB5V 1
MCLK
PSW
NQR0286-007X L703
NQR0713-001X
R721
100
100
0v
C12 MCLK STA1080 VDD M12
? C2020
C2021 0.01u
(DCF)
5.1V
IC540
5.1V
C13 PSW VDD M11 OUT
6
USB5V 2 ? C712 1.4v 0V IN 0V
D-1 ? R753 C14 M3_SXTAL_IN VDD M10 ILIM
5
C541
D- 3
Accordo 2 AUD12V GND
0.01u
D+1 SW1 3.3V PON_USB0 1u 3.2V OC 3.2V
C540
C15 SW1 VDD M9
1u
10u
D+ 4 LCD_DATA_LCD R739 2v VREF6V VREF6V EN
1k
1u
2.2k
C16 LCD_DATA_IN VDD M8
12k R540
R542
? C2084
MGND 5
R740 C17 (DAC_AGND) VDD M7
C2081
C2094
C2023
C2026
MGND 6 M_FL_OUT 4.7u 4.7k 1.4v R543
TL80
47k
47k
47k
47k
47k
47k
C18 SP_FL M6
1/10W
TL84 VDD C194 ? C199
F_AUXL 7 M_SWL_OUT (FL) 1.4v 1.2v 12V VIN 12V R184
(SWL) 10u
6
C19 SW_L 1.2V M5 CONTROL 3.9k 0
F_AUXG 8 SQI_SCK C2100 R829 L822 0v 0v L707 SPI_DATA_MICON 0V VADJ 1.2V C2117 TL36 C542
5
4.7u D1 SQI_SCK SPI_DATA_MICON M4 (VREF) 10u C2052
*R110
*R111
*R112
*R113
*R114
*R115
F_AUXR 9 L826 R785 AUD12V 1.2V GND 6V 100p 0.01u
SQI_SIO1 0 LB73H0CT-002 3.3V 3.3v 0 SPI_DATA_SPI VOUT _0.5%
LB73H0CT-002
4
D2 SQI_SIO1 SPI_DATA_SPI M3
0.01u
REMO 10 L824 R783 L706 NOISEBYPASS AUD12V
C191
C193
10u
C192
10u
SQI_CEON 3.3V 3.3v 0 SPI_CLK
R198
LB73H0CT-002
1k
ENC2 D3 SQI_CEOn SPI_CLK M2
0.5%
ENC2 11 SQI_SIO0 3.3V 3.3v R781 LB73H0CT-002 SPI_EN IC164 GND1
ENC1 L827 LB73H0CT-002 D4 0
SQI_SIO0 SPI_EN M1 NJM11100F1
ENC1 12 LB73H0CT-002 0v R782 D+0
LCD_CE L2009 D5 0
R737 NC D+0 L19
LCD_CE 13 NQR0713-001X *R787 *R786
LCD_DATA_SYS NRST 100 ? C2075 0v 0v 0 0 D-0 TU3V3 AUD12V VDD CD7V ILM9V TL30
D6 NRST D-0 L18 SXM_R/MIC_N PIN 2 - 5 IC101,V=6V R120
LCD_DATA_SYS 14 ?R724 R723 *R780 *R784 (EXT)
LCD_CLK MLD 0v 0 0 SXM_L C122 4.7u TL29 14.3V
100 D7 MLD USB1_AGND L17
18p
PIN 13 - 16 IC101,V=6V
NQR0713-001X
1
LCD_CLK 15 R743 R788 _0.5% 91k (ANT) EXT
L2008
REG_SDA 3.3V 1.2v *IC101
TL95
*R2030
L2000
(SXL)
LCD_DATA_LCD 2.2k D8 REG_SDA 121K_1% L16
R125
TL23
C120
TC74HCT4053FT
47k
LB73H0CT-002
*R2032
2
LCD_DATA_LCD 16 STAT R794 3.3V 82k R789 (AUD) ANT
10 11 12 13 14 15 16 12V
RESET D9 STAT L15 _0.5% 39k 4.7u TL72 TL22 11.5V
3
RESET 17 LRCK L705 0v 3.3v L701 6V (SOR) AUDIO
R748 100 100 VCC (ILM) 9.0V
D10 LRCK USB0_VDD3V3 L14 R121
12V
6V
6V
6V
1
TL181
4
ILM 18 CD_SRDATA_CD 3.3V 3.3v AUX_L 1Y (CD) ILM
NQR0713-001X ? R749 R750 Y-COM
C127
100 D11 SRDATA VDD L13 7.0V
2
91k 8 7 6 5
5p
10u
5
GND 19 DRV_MUTE 0v SXM_G/MIC_P 0Y TL215 CD
?R751
(SXR)
X-COM
C124
D12 DRV_MUTE GND L12 D903 6.0V
R127
47k
TL97
VCC
OUT2
-IN2
+IN2
3
6
PANEL3.3V 20 R744 100 *R2031 1Z TL216 ACC
DA2J101
C2025 SK34A-L-X
NJM8065V
? R745
D13 TEST_POINT GND L11 1X 13.9V
C2086
0.01u
0
IC102
D2009
7
0.01u 0v AUX_G Z-COM 6V TL214 VCC2
D14 M3_SXTAL_OUT GND L10 0X D902 14.1V
OUT1
8
? R716 0Z VCC1
*R107
+IN1
BLKCK R715 3.3V 0V 0V
VEE
100
-IN1
10u
D15 BLKCK GND L9 A SK34A-L-X 0V
5p
0
6
TL110
9
DIM_IN 3.3V 0V INH 0V GND
C125
C126
(SXG)
D16 DIM_IN GND L8 B REG_SCL 3.3V
TL96
R126
47k
7
1 2 3 4
10
TL117 1.4v 0V VEE 0V TL24 SCL
(DIMMER_IN)
6V
6V
6V
0V
? R754 D17 10nF//10uF GND L7 C (VDD) 3.3V
*R106 0
8
9
? C1048
*R105 0
11
C2090 TL82 C706 C707 C2069 GND R122 VDD
M_FR_OUT 4.7u (FR) 1.4v 3.3v REG_SDA 3.3V
10u 0.022u 0.022u D18 SP_FR VDD L6
12
TL83 TL33 SDA
M_RR_OUT 1.4v 1.2v AUX_R 91k
R124
(RR)
47k
C121
D19 SP_RR 1.2V L5 GND5 (V6) 5.1V
18p
13
SQI_SIO2 C2089 L828 X702 3.3V BT_UART0_RTS C123 TL28 R905 TL63 V6IN
4.7u E1 SQI_SIO2 BT_UART0_RTS L4 REG_FLAG (T3V3) (FLG) 3.3V
VA703
VA705
91k
14
FLG
D701
NAX1256-001X AUD_SEL
D702
D704
D706
D707
D711
D710
D709
SQI_FB LB73H0CT-002 0v BT_UART0_CTS TL73 R123

E2 SQI_FB BT_UART0_CTS L3 100 3.3V
AUX_SXM_L (SOL) 4.7u VREF6V
15
C704 TU3.3V
32.768kHz
3.3v R2016 22 BT_I2S0_FS
? C1049
L829 15p E3 NC BT_I2S0_FS L2 AUX_SXM_R R984
LB73H0CT-002
V
? C1052
3.3v R2004 22 BT_I2S0_BCLK
100u 6.3V
22u 16V
47k 1/4W
470u 16V
E4 NC BT_I2S0_BCLK L1 47k
? R1051 ? C1051
1u 10V
1u 10V
1u 10V
1u 10V
1u 10V
0v R792 D+1 1/4W
? C915
0 !
0.01u
0.22u
K7: GND
K8: GND
K9: GND
E5 NC D+1 K19
0.1u
R982
C705
F0K-0010-00
F0K-0040-00
0.1u
3.3V 0v R790 D-1
DZ2J051M
DZ2J051M
DZ2J051M
DZ2J051M
DZ2J051M
DZ2J051M
DZ2J051M
DZ2J051M
15p 0 IC901
1u
E6
E18: STR_REMO_2
E19: STR_REMO_1
C2036 VDD D-1 K18 C222 0.033u Q220
? C913
R746 R237
1u
? R1052
0.1u 2SC1623/5-6/-X LV5685PV-H
0.033u
SW1V2
0
21
C223
R236
E7 VDD USB0_AGND K17
R223
1/4W
E15: MIC_BIAS
C932
GND6 AUD12V
C905
C916
2.2k
? R2052
8.2k
R227
C912
C906
C907
C911
C914
C904
C908
C903
C390
C909
1.1v 4.7u 470
0
470p
120k
0
1u
(PDET) E8 VDD 4.7uF K16
11.5V
C234
H13 USB_VREG3V3_1V1 6.8k
USB_VREG3V3_1V8
0.01u
TL64 PAN_DET
?R2027
BT_DATA_SYS(TX)
1.2v 1.9v R233
*R2025
*R2026
C235
R981
1
PAN_DET E9 C730 100p C731 11.5V
BT_DATA_BT(RX)
1.2V 4.7uF K15
E16: NC
E17: NC
V+ 680
F1 : NC
8
REMO
MBRX130
TL205
? R235
C1900
G14 DAC_I/O_AGND
H15 DAC_I/O_AVDD
C227
AOUTPUT
H14 ADC0_1_AVDD
ADC0_1_VREF
2
REMO E10 1.2V NC K14 C728 100p C729 0.1u11.5V 11.5V
R234
D390
ADC_1_AGND
R224
F15 ADC2_VREFP
BOUTPUT R226 C228 0.01u
4.7k 1/4W
F13 ADC2_AGND
BT_12S0_RX
F17 AUX_SXM_R
7
G13 ADC2_AVDD
BT_12S0_TX
4.7u
F16 AUX_SXM_L
0v 3.3v C236 0V A-INPUT D222
10k
F14 DAC_AGND
1.2k
G15 DAC_AVDD
1/4W
3
USB5V H16 TEL_MUTE 0V 1u
10nF//10uF
10nF//10uF
E11 JTAG_SEL VDD K13 DZ2J056M
C2024
(5VF) B-INPUT
C2019
6.8k REMOTE OUT

470p
C2063
0.1u
6
H17 PULL_LO
H18 PULL_LO
H19 PULL_LO
TL34 C2065 1u R755 10k A+INPUT C226 GND5
G16 STAGE1
G17 STAGE2
BT_RST
R220 (MICP) R980

4
USB5V
0.22u
E12 ADC_VREF GND K12 0V 0V 22p
? C392
C391
R390
(D-F) MIC_P B+INPUT
G19 MIC_N
G18 MIC_P
100 TL91
5
D-1
OVP1
QGA2001F1-02
TL102
F19 TU.R
C2064 100p V- 1 T1
F10 GND
F11 GND
F12 GND
GND
GND
GND
G10 GND
G11 GND
G12 GND
GND
GND
GND
H10 GND
H11 GND
H12 GND
GND
GND
GND
GND
GND
GND
F18 TU.L
VDD
VDD
VDD
VDD
VDD
OVP
VDD
1.2V
1.2V
1.2V
1.2V
1.2V
1.2V
1u
5
D- C224 R229
R225
E13 VDD
470p
GND K11 C229 R221 TL90 ? R381
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
ENC1 C710 1.2k
33k
TL17 C2115 470p 1.2v 1u 2 T2 TL21
R238 10k
E14 1.2V
6
ENC1
R230
GND K10
C231
(D+F) C237 IC220 100 (MICN) (MEM)
120k
D+1 IC930 QQR1909-001
E16
E17
E18
E19
*CN220
TL101 NJM8065V
MBR0530-X
J10
J11
J12
J13
J14
J15
J16
J17
J18
J19
0.01u
E15
DZ2J068M
G1
G2
G3
G4
G5
G6
G7
G8
G9
H1
H2
H3
H4
H5
H6
H7
H8
H9
K1
K2
K3
K4
K5
K6
K7
K8
K9
7
D+
F1
F2
F3
F4
F5
F6
F7
F8
F9
BD33IC0WEFJ L990
DZ2J068M
2200p J1
J2
J3
J4
J5
J6
J7
J8
J9
C2047 R231
? R228
D391
ENC2 C709 10p !
0
TL204
9
0.01u
*D221
*D220
?C232
8
ENC2 SW3V3
?C233
(GND) TL38 C990
?C220
?C221
MIC_N 10k D990
3v
0.8v
TL37 SW3V3 (GND2) 2200u
C230
R232
R222
1.5v
1.5v
3.3v
3.3v
3.3v
3.3v
10k
C2022
9
USB_GND 1N5401-BPC04
1u
IPOD
0.01u
0.01u
TL122
3.1V C225 1u 16V

0v
2v
0.1u LCD_CLK NC_4
0.01u
TL203
4
10
3.4v
3.3v
3.3v
*R769
*R771
LCD_CLK EN
3.3v
C2045 GND_3 0V
470u
IC411
22
100
100
22
TL202
3
4700p (IP3)
11
USB_GND NC_6
4.7k
4.7k
4.7k
16V
? C2250
470p
R772
C2005 TL59 MFI337S395901 3.2V

(ASXR)
TL10 LCD_DATA_LCD FB
2
470p
12
TL87
LCD_DATA_LCD NC_7
100
GND6
1u
C2016
C2118
4.3V
To SWITCH PWB ASSY

(IP2)
9
C2062 1u LCD_CE VO
R2003
TL118
R2017
TL11
1
0.01u TL58 CD_DSP_SW
13
C724
C726
R777
R778
LCD_CE VCC
C2018
C930
0.1u
3.2V C2108
R414
R413
R412
LCD_DATA_SYS TL60
C711
C931
TL12
14
LCD_DATA_SYS 0V REMAP1 470p
10u
(IP4) REMAP1
C719
C2061 NC4 GND4

5
ILM9V NC5 TL128
(XK6-0110-1x)
TL201 0.01u *R401 *R400
15
ILM IPOD_SCL R411 3.3V 0V

C2003 NC3 REMAP0 REMAP0 REMO 0 1k
? C2004
6
TL27 0.1u SCL TL129

16
Panel3.3V (P3V3) IPOD_SDA 100 3.3V 3.3V

SDA
7
TL200 RST
CN1
17
GND 3.3V 0V TL223 *D401

(AR) GND TL66
8
C720
TL94 3.2V VCC JATG_TRSTN *D400 DZ2J051M

(S3V3) (TRST)
18
(REM)
C722
10u
F_AUXR RB521SM-30-X
4700p C2060
C410 TL25 TL43 (AANT)
10u
10u
(AG) TL57
GS1J-LTP-X
TL93 C2014 TL65
19
D930
0.1u
DEBUGING
F_AUXG VDD JTAG_TDI
R773
(IP1) (TDO)
47k
100p *R371 12k

100p
0V TL40
0.1u
TL92 (AL) SW3V3

(ASXL)
20
F_AUXL IC941
TL86
? C411
JTAG_TMS (TMS) CD3V3 *D370
LR73Z0AD100M
R940 *C370 0.1u
C727
3.2V Q920 TL41 BU33TD3WG-W BAW56-TP-X
L411
C725
1/4W
4.7u
L2005
C716
C2072 R410 JTAG_TCK (TCK) 1

*R768
*R770
22
LTA014YEBFS8 *R372
TL67
(OE)
4700p 100 TL42 5.1V 3.3V *R370 68k
JTAG_TDO (TDO)
470p
*C1010
470p
*C1011
470p
*C1012
470p
*C1013
470p
*C1014
470p
*C1015
470p
*C1016
470p
*C1017
VIN VOUT
5
TL39 10k
0V TL239 TEL_MUTE
QGZ2006J1-20 R100 470 GND
2
C105 RESET (CD3V3)
R101
10u
C941
AUX_R TL224
C940
(3.2V)
0.1u
TL217
CN701 STBY
? CN400
NC
4
C2031 0.01u 4.7u ? R405 MRC_DB_UART1_RX
? C101
0 DIM_IN
?R103
TL225
1u
C942
C104 MRC_DATA_MRC
C106 1u AUX_G
RR+
FR+
RR-
FR-
RL-
FL-
RL+
FL+
BT_DATA_SYS
? R403 ? R406 TL226
BT_DATA_BT
AUX_SXM_R
AUX_SXM_L
10u
BT_I2S0_RX
BT_I2S0_TX
? C102
REMO1 1 MRC_DATA_SYS
TEL_MUTE
?R104
? Q360
? D404
? D402
? D403
? R404 TL227
PWR_EN
? R362
? C780
? C781
C103 ? R361
BT_RST
? R764
? R762
R102 REMO2 2 18 17 16 1 15 2 14 3 13 4 12 5 11 6 10 7 9 8
? C360
MIC_N
MIC_P
4.7u AUX_L MRC_DB_UART1_TX

OVP1
TU.R
TU.L
OVP
TL228
? R364 ? R363
0 GND 3
? D2002
PFUSE1
?D2001
? C361
F2
? R360
DZ2J075M
DZ2J075M
? D360
FOR DOP STEERING REMOTE
D101
D100
F901
FUSE 10A
FZB10BT-100
MEMORY
GND
ACC
*TEL MUTE
REMOTE/P-CON
*OE REMOTE
*ANTENNA
REAR RIGHT (+)
FRONT RIGHT (+)
REAR RIGHT (-)
FRONT RIGHT (-)
REAR LEFT (-)
FRONT LEFT (-)
REAR LEFT (+)
FRONT LEFT (+)
!
C2048 0.01u
C2050 0.01u
CN990
GND1 QNZ0607-001
* POWER CORD ASS'Y
LTC043TEB-X LTC044EUBFS8 LTA043EEBFS8
MODEL LIST:
4.7K 47K 4.7K
47K 4.7K Y No X No Model
YK1-0410-10 XK1-0500-10 KDC-BT565UK
YK1-0410-11 XK1-0500-11 KDC-X500K
LTC024EEB-X LTC043ZUBFS8 LTA014YEBFS8 YK1-0410-12 XK1-0500-12 KMR-D765BTK
22K 4.7K 10K
YK1-0412-71 XK1-0502-71 KDC-X5000BTE
22K 47K 47K
YK1-0410-01 XK1-0500-01 U410BTJ
22K
LTA024EEB-X
10K
LTC014EEBFS8
MAIN PWB:J7J-0170-**

(No.WA185<Rev.001>)5/16
MAIN PWB ASSY(2/2) (XK1-050x-xx)
REF number XK1-0500-10 XK1-0500-11 XK1-0500-12 XK1-0502-71 XK1-0500-01 REF number XK1-0500-10 XK1-0500-11 XK1-0500-12 XK1-0502-71 XK1-0500-01 X Number XK1-0500-10 XK1-0500-11 XK1-0500-12 XK1-0502-71 XK1-0500-01 SYMBOL MN NO SHEET NO ADDRESS ISSUED DATE
Model Name KDC-BT565UK KDC-X500K KMR-D765BTK KDC-X5000BTE U410BTJ Model Name KDC-BT565UK KDC-X500K KMR-D765BTK KDC-X5000BTE U410BTJ Model Name KDC-BT565UK KDC-X500K KMR-D765BTK KDC-X5000BTE U410BTJ 2D-R2091,R2092
C141 - - CK73HXR1A105K - CK73HXR1A105K R111 RK73HB1J473J RK73HB1J473J RK73HB1J473J - - Power Cord E3A-0052-00 E3A-0052-00 QAM1399-001 QAM1333-001 QAM1337-001 2J-D701,D710,D711,VA703,VA705
C142 - - CK73FXR0J106K - CK73FXR0J106K R112 RK73HB1J473J RK73HB1J473J RK73HB1J473J - - 2L-C2016
C143 - - CC73HCH1H270J - CC73HCH1H270J R113 RK73GB2A473J RK73GB2A473J RK73GB2A473J - - 2M-C101,C102,R103,R104,C2031
C144 - - CC73HCH1H270J - CC73HCH1H270J R114 RK73HB1J473J RK73HB1J473J RK73HB1J473J - - 3F-C2006,R2014,R2039
C145 - - CK73HBB1H471K - CK73HBB1H471K R115 RK73HB1J473J RK73HB1J473J RK73HB1J473J - - 3G-C2043
C146 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R141 - - RK73HB1J222J - RK73HB1J222J 4E-C2032,C2034
C160 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R143 - - RK73HH1J123D - RK73HH1J123D 5F-C739
C161 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R144 - - RK73GB2A000J - RK73GB2A000J 5G-C701
C162 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R146 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 5H-R729
C163 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R148 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 5J-C2025
C164 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R150 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 5L-C2014
C165 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R151 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 6B-R252
C166 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R153 RK73GB2A200J RK73GB2A200J RK73GB2A200J RK73GB2A200J - 6C-C251,R156
C169 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R155 RK73GB2A200J RK73GB2A200J RK73GB2A200J RK73GB2A200J - 6D-R2005
C170 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R156 - - - - RK73GB2A200J 6F-R701
C171 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R161 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 6I-R739
C172 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R162 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 6K-C704,C705
C173 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R163 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 7C-D2007,R2082,Q370,Q380,R322,
C174 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R164 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J R342,R352,R332
C175 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R165 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 8B-R250,R251,R253
C176 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R166 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 8C-R2042,Q240,R264,R254
C179 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R168 RK73GB2A200J RK73GB2A200J RK73GB2A200J RK73GB2A200J - 10B-C2017
C180 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R169 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 10C-R680
C181 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R170 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 11B-R2022
C182 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R171 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 11E-R817
C183 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R172 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 13C-C472
C184 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R173 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 13L-R2003,R2017,C2018
C185 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R174 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 14E-C2070,R807
C186 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R175 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 14G-R798
C189 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R176 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 14I-R781,R782,R783,R785
C190 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R178 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 14K-R2004,R2016
C195 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R180 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 14L-C2118
C196 CC73HCH1H470J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J CC73HCH1H270J R181 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 15B-R303,R305
C197 CK73FXR1C475K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K R182 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 15C-R152,R154,R167,R177,R158,
C198 CC73HCH1H271J CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K CK73HBB1H221K R183 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J R159,R200,R201,R302
C1010 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R185 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 15F-C740
C1011 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R186 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 16D-R160,R2056
C1012 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R187 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 16E-R147,R149,R2057
C1013 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R188 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 16F-R179,R2061,R2062
C1014 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R190 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 16G-R189,R2066
C1015 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R191 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 16H-R239,R2065
C1016 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R192 RK73GB2A200J RK73GB2A200J RK73GB2A200J RK73GB2A200J - ▲1 2D19894L 1/2 16L-C2250 SOO CH 14-08-2015
C1017 CK73GBB1H471K CK73GBB1H471K CK73GBB1H471K - - R193 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 17E-C177,C178
C251 - - - - CK73EBB1A106K R194 RK73GB2A822J RK73GB2A202J RK73GB2A202J RK73GB2A202J RK73GB2A202J 17F-C167,C168
C321 CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K - R195 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 17I-C194
C331 CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K - R196 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 18D-R2072
C341 CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K - R197 RK73HB1J753J RK73HB1J823J RK73HB1J823J RK73HB1J823J RK73HB1J823J 18E-R2070
C351 CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K CK73EBB1A106K - R199 RK73GB2A183J RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J 18G-R2071
C370 CK73GXR1H104K CK73GXR1H104K CK73GXR1H104K CK73GXR1H104K - R240 RK73HB1J752J RK73HB1J153J RK73HB1J153J RK73HB1J153J RK73HB1J153J 18H-C2116,D2008,GND5
C472 CK73GXR1H104K CK73GXR1H104K CK73GXR1H104K - - R250 - - - - RK73HB1J181J 18I-C2117
C473 CK73FXR1C106K CK73FXR1C106K CK73FXR1C106K - - R251 - - - - RK73HB1J223J 18J-R120,R121,R122,R123
C474 CK73GXR1C225K CK73GXR1C225K CK73GXR1C225K - - R252 - - - - RK73GB2A331J 19G-D2005,D2006,Q2001,R2053,R2068
C475 CK73GXR1C225K CK73GXR1C225K CK73GXR1C225K - - R253 RK73GB2A000J RK73GB2A000J RK73GB2A000J RK73GB2A000J - 19I-C2021
C480 - - CK73HBB1H103K - - R254 - - - - RK73HB1J472J 19J-C2086,D2009,GND5
C481 - - CK73HBB1A104K - - R320 RK73GB2A181J RK73GB2A181J RK73GB2A181J RK73GB2A181J - 20D-Q478,R497
C482 - - CK73HXR1A105K - - R321 RK73HB1J223J RK73HB1J223J RK73HB1J223J RK73HB1J223J - 20H-C2029,C2030,C2080,R2040
C483 - - CK73HBB1A104K - - R322 RK73HB1J472J RK73HB1J472J RK73HB1J472J RK73HB1J472J - 20J-C1048
C484 - - CK73GBB1H102K - - R323 RK73GB2A331J RK73GB2A331J RK73GB2A331J RK73GB2A331J - 20K-C1049,C1051,R1051
C485 - - CK73HBB1H103K - - R330 RK73GB2A181J RK73GB2A181J RK73GB2A181J RK73GB2A181J - 21F-R2086
C486 - - CK73HBB1E682K - - R331 RK73HB1J223J RK73HB1J223J RK73HB1J223J RK73HB1J223J - 21G-F3,IC863
C884 - - QEZ0850-157Z - QEZ0850-157Z R332 RK73HB1J472J RK73HB1J472J RK73HB1J472J RK73HB1J472J - 22C-C2120
C885 - - CK73EBB1A106K - CK73EBB1A106K R333 RK73GB2A331J RK73GB2A331J RK73GB2A331J RK73GB2A331J - 22D-C2085
C887 - - CK73GXR1H104K - CK73GXR1H104K R340 RK73GB2A181J RK73GB2A181J RK73GB2A181J RK73GB2A181J - 22E-C2078,C2079
C888 - - CK73GXR1H104K - CK73GXR1H104K R341 RK73HB1J223J RK73HB1J223J RK73HB1J223J RK73HB1J223J - 22F-C2082
C889 - - CK73GXR1H104K - CK73GXR1H104K R342 RK73HB1J472J RK73HB1J472J RK73HB1J472J RK73HB1J472J - 22G-Q880
C890 - - CK73EBB1A106K - CK73EBB1A106K R343 RK73GB2A331J RK73GB2A331J RK73GB2A331J RK73GB2A331J - 22F-C879,R877,R878,
C891 - - CK73EBB1A106K - CK73EBB1A106K R350 RK73GB2A181J RK73GB2A181J RK73GB2A181J RK73GB2A181J - -Q865,VA140,VA141

C892 - - CK73HBB0J224K - CK73HBB0J224K R351 RK73HB1J223J RK73HB1J223J RK73HB1J223J RK73HB1J223J - 22H-C2083
C893 - - CK73HBB0J224K - CK73HBB0J224K R352 RK73HB1J472J RK73HB1J472J RK73HB1J472J RK73HB1J472J - 23F-C870,R870,C2082
C894 - - CC73HCH1H150J - CC73HCH1H150J R353 RK73GB2A331J RK73GB2A331J RK73GB2A331J RK73GB2A331J - 23G-R874
C895 - - CK73HBB1A104K - CK73HBB1A104K R371 RK73GB2A123J RK73GB2A123J RK73GB2A123J RK73GB2A123J - 19E-IC821,IC822
C2017 - - - CK73GBB1H472K CK73GBB1H472K R372 RK73GB2A103J RK73GB2A103J RK73GB2A103J RK73GB2A103J - 1A-VA600
C2078 - - CK73GBB1H472K - CK73GBB1H472K R401 - - - - RK73GB2A000J 15B-R303
C2082 - - CK73GBB1H103K - CK73GBB1H103K R467 RK73HB1J100J RK73HB1J100J RK73HB1J100J - - 14E-C2070
C2085 - - CK73GBB1H103K - - R468 RK73HB1J4R7J RK73HB1J4R7J RK73HB1J4R7J - - 6I-C712
CN141 - - QGA2001C1-05 - QGA2001C1-05 R469 RK73HB1J100J RK73HB1J100J RK73HB1J100J - - 2E-C251
CN220 QGA2001F1-02 QGA2001F1-02 QGA2001F1-02 - - R471 RK73HB1J101J RK73HB1J101J RK73HB1J101J - - 2F-C472
CN481 - - QGA2001F1-06 - - R472 RK73HB1J101J RK73HB1J101J RK73HB1J101J - - 2H-C2017,C2078,C2082,C2085
D140 - - UDZV5.1B-X - UDZV5.1B-X R473 RK73GB2A472J RK73GB2A472J RK73GB2A472J - - 2K-IC863
D141 - - UDZV5.1B-X - UDZV5.1B-X R474 RK73FB2B221J RK73FB2B221J RK73FB2B221J - - 2M-Q370,Q380
D220 DZ2J068M DZ2J068M DZ2J068M - - R475 RK73HB1J100J RK73HB1J100J RK73HB1J100J - - 2N-Q487,Q865
D220 UDZV6.8B-X UDZV6.8B-X UDZV6.8B-X - - R476 RK73GB2A223J RK73GB2A223J RK73GB2A223J - - 6C-R156
D221 DZ2J068M DZ2J068M DZ2J068M - - R477 RK73GB2A104J RK73GB2A104J RK73GB2A104J - - 6F-R250,R251,R252,R253,R254
D221 UDZV6.8B-X UDZV6.8B-X UDZV6.8B-X - - R480 - - RK73HB1J334J - - 6G-R322,R332,R342
D370 BAW56-TP-X BAW56-TP-X BAW56-TP-X BAW56-TP-X - R481 - - RK73EB2E3R3J - - 2/2 6H-R352
D370 DA3X102D-X DA3X102D-X DA3X102D-X DA3X102D-X - R482 - - RK73EB2E3R3J - - 6K-R497
D400 RB521SM-30-X RB521SM-30-X RB521SM-30-X RB521SM-30-X - R483 - - RK73HB1J104J - - 6L-R817
D400 DB2S310 DB2S310 DB2S310 DB2S310 - R484 - - RK73HB1J473J - - 6N-R2086,VA140,VA141
D401 DZ2J051M DZ2J051M DZ2J051M DZ2J051M - R485 - - RK73GB2A153J - - 2L-Q250,Q320,Q330,Q340,Q350
D401 UDZV5.1B-X UDZV5.1B-X UDZV5.1B-X UDZV5.1B-X - R486 - - RK73GB2A473J - - 2I-D140,D141,D220,D221,D370
D472 RSB6.8SM-X RSB6.8SM-X RSB6.8SM-X - - R487 - - RK73HB1J223J - - OR Part 2J-D400,D401,D475,D476,D480
D474 RSB6.8SM-X RSB6.8SM-X RSB6.8SM-X - - R488 - - RK73HB1J104J - - 2K-D481,D482
D475 DZ2J068M DZ2J068M DZ2J068M - - R489 - - RK73HB1J333J - -
D475 UDZV6.8B-X UDZV6.8B-X UDZV6.8B-X - - R490 - - RK73HB1J183J - -
D476 DZ2J068M DZ2J068M DZ2J068M - - R491 - - RK73EB2E101J - -
D476 UDZV6.8B-X UDZV6.8B-X UDZV6.8B-X - - R492 - - RK73GB2A102J - -
D480 - - DZ2J062M - - R493 - - RK73EB2E101J - -
D480 - - UDZV6.2B-X - - R494 - - RK73HB1J332J - -
D481 - - DZ2J062M - - R495 - - RK73EB2E100J - -
D481 - - UDZV6.2B-X - - R496 - - RK73GB2A473J - -
D482 - - DZ2J051M - - R497 - - RK73GB2A332J - -
D482 - - UDZV5.1B-X - - R768 - - - RK73GB2A393J RK73GB2A273J
IC101 TC74HCT4053FT TC74HCT4053FT TC74HCT4053FT - - R769 RK73HB1J473J RK73HB1J473J RK73HB1J473J RK73HB1J822J RK73HB1J223J
IC141 - - BD2242G-G - BD2242G-G STAGE 1 (V) 0 0 0 0.6 1.5
IC470 TC7SH08FU-X TC7SH08FU-X TC7SH08FU-X - - R770 RK73GB2A223J RK73GB2A153J RK73GB2A822J - RK73GB2A393J
IC481 - - SN65HVD3082ED - - R771 RK73HB1J273J RK73HB1J333J RK73HB1J393J RK73HB1J473J RK73HB1J822J
IC482 - - TC7SH08FU-X - - STAGE 2 (V) 1.8 2.3 2.7 0 0.6
IC863 - - MP9943AGQ - MP9943AGQ R780 - - RK73GB2A000J - RK73GB2A000J
IC1303 W0C-0168-00 W0C-0168-00 W0C-0168-00 W0C-0167-00 W0C-0167-00 R784 - - RK73HB1J000J - RK73HB1J000J
J220 - - - E1B-0013-00 E1B-0013-00 R786 - - RK73HB1J000J - RK73HB1J000J
J321 QNN0866-001 QNN0866-001 QNN0866-001 QNN0866-001 QNN0874-001 R787 - - RK73GB2A000J - RK73GB2A000J
J470 QNZ0907-001 QNZ0907-001 QNZ0907-001 - - R802 - - RK73HB1J473J RK73HB1J473J -
L140 - - L7K-0030-00 - L7K-0030-00 R803 RK73HB1J225J RK73HB1J225J - - RK73HB1J225J
L865 - - NQLL6EM-100X - NQLL6EM-100X R817 - - RK73HB1J222J - RK73HB1J222J
L866 - - NQLH65M-4R7X - NQLH65M-4R7X R879 - - RK73HB1J393J - RK73HB1J393J
Q250 - - - - LTC043TEB-X R881 - - RK73HB1J200J - RK73HB1J200J
Q320 LTC043TEB-X LTC043TEB-X LTC043TEB-X LTC043TEB-X - R882 - - RK73HH1J393D - RK73HH1J393D
Q350 LTC043TEB-X LTC043TEB-X LTC043TEB-X LTC043TEB-X - R886 - - RK73GB2A512J - RK73GB2A512J
Q370 IMX9 IMX9 IMX9 IMX9 - R887 - - RK73GB2A222J - RK73GB2A222J
Q380 IMX9 IMX9 IMX9 IMX9 - R888 - - RK73GB2A102J - RK73GB2A102J
Q470 LTC014EEBFS8 LTC014EEBFS8 LTC014EEBFS8 - - R1302 - - - RK73HB1J101J RK73HB1J101J
Q471 LTC043TEB-X LTC043TEB-X LTC043TEB-X - - R1303 - - - RK73HB1J101J RK73HB1J101J
Q480 - - LSCR523UBFS8 - - R2007 RK73HB1J222J RK73HB1J222J RK73HB1J222J - -
Q481 - - LSCR523UBFS8 - - R2020 - - - RK73HB1J000J RK73HB1J000J
Q482 - - LSCR523UBFS8 - - R2021 - - - RK73HB1J000J RK73HB1J000J
Q483 - - LSAR523UBFS8 - - R2023 - - - RK73HB1J000J RK73HB1J000J
Q484 - - RSR015P06 - - R2025 - - - RK73HB1J000J RK73HB1J000J
Q485 - - LTC043ZUBFS8 - - R2026 - - - RK73HGB2A00J RK73GB2A000J
Q486 - - LTC043ZUBFS8 - - R2030 RK73GB2A000J RK73GB2A000J RK73GB2A000J - -
Q487 - - LTC044EUBFS8 - - R2031 RK73GB2A000J RK73GB2A000J RK73GB2A000J - -
Q865 - - LTC043EUBFS8 - LTC043EUBFS8 R2032 RK73GB2A000J RK73GB2A000J RK73GB2A000J - -
R105 - - - RK73GB2A000J RK73GB2A000J R2086 - - RK73GB2A000J - RK73GB2A000J
R106 - - - RK73HB1J000J RK73HB1J000J VA480 - - NAF0029-002X - -
R107 - - - RK73GB2A000J RK73GB2A000J VA140 - - F0K-0010-00 - F0K-0010-00
R110 RK73HB1J473J RK73HB1J473J RK73HB1J473J - - VA141 - - F0K-0010-00 - F0K-0010-00

(No.WA185<Rev.001>)6/16
SWITCH PWB ASSY (XK6-0110-1x)
SWITCH PWB : J7J-0201-**
J60
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
S1
S2
S3
S4
S5
S6
S7
S8
S9
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
S42
S43
S44
S45
S46
S47
S48
0v
3 4
0v
S20 QNS0323-001
*IC90 QSW1288-001
GND1
GND2
3
PIC95603-X C61 C60

2
AUX
VOUT
1
VCC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 1000p 1000p
2 1 ? D61 RSB6.8SM-X
? D60
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
SEG48
3.2v 3.3v
*R1008
33k 33k
? R1007
*R1009
? R1010
1/8W
1/8W
CN1
00

Kenwood Kdc-Bt565u Kdc-x500 Kdc-x5000bt Kmr-d765bt SM

Uploaded by

Copyright:

Available Formats

Kenwood Kdc-Bt565u Kdc-x500 Kdc-x5000bt Kmr-d765bt SM

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kenwood Kdc-Bt565u Kdc-x500 Kdc-x5000bt Kmr-d765bt SM

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

DC cord DC cord Screw set Tap screw (M2x8) Microphone

Hook M. sleeve assy Trim plate Remocon

This product uses Lead Free solder.

COPYRIGHT © 2015 JVC KENWOOD Corporation No.WA185<Rev.001>

1.9 Important for laser products

3.CAUTION : Visible and/or invisible laser radiation when

Part Number Part Name SPEC

FRONT CHASSIS ASSY

c c c c Do not touch DAMPER.

DO NOT TOUCH AREA

• THESE PARTS NEED CAUTION OF HANDLING

• NOTICE FOR HANDRIG OF ROLLER LEVER ASSY

Do not handle roller part. Black

• NOTICE FOR HANDRIG OF MD CHASSIS ASSY

Do not handle the

CN1 CD Player unit

Do not handle the lens part.

C Main shaft Pickup assy

SEARCH RETURN VOL / ROTARY

Various setting item Setting value

All lights ON All lights ON (Switch with other display)

All Lights ON/OFF

Item Operation Display content Details

In addition, upon enter to this mode, P-CON is turned

Shift to TUNER setting mode after switching to

Upon source change to USB source or USB

Verifying: Show "iPod: ##"

In addition, upon enter to this mode, P-CON is

When a judgment result is OK, P-CON is

S E A R C H I N G Upon entering this mode, P-CON is turned ON.

It is able to enter into this mode by remote control op-

4.3.3 Common operation mode for only STANDBY sources

BT module BT module software version display

BT module BT module address display

BT module PIN BT module PIN code display

BT module BT module friendly name display

00 to 50 are displayed in "XX".

Item Operation Display content Details

BER S2 B E S 2 # # # BER S2 : 0 to 100 (DEC) "###"

BER T B E T # # # BER T : 0 to 100 (DEC) "###"

SuspendYear/Month/Day [Module Version]

Init Lock Passcode I N I T C O D E

Press [Rotary] knob Press [Rotary] knob

Press [Rotary] knob

CLEARING Blinking 500ms

Press [RETURN] key

YES < Y E S > / N O

Item Operation Display content Details

Item Operation Display content Details

CH0 Offset C 0 O F S E T # # # 0 to 999 (DEC) "###"

CH1 Offset ROTARY C 1 O F S E T # # # 0 to 999 (DEC) "###"

CH2 Offset C 2 O F S E T # # # 0 to 999 (DEC) "###"

CH3 Offset C 3 O F S E T # # # 0 to 999 (DEC) "###"

Demo: No demo animation

Power on animation: Show carmaker's name

Normal Display @ @ @ @ @ @ @ @ @ @ @ @ @ Return to normal display mode

Pressing Indicated “Running Mode”

insert the Repeated the eject.

R702 2.2k M_FL_OUT C171 R173 10u ILIM

C889 C888 *L865