IVECO Stralis Euro 4 - 5 Bodybuilder Instructions

STRALIS AS/AT/AD
EURO 4/5
BODYBUILDERS INSTRUCTIONS
E
G
N
A
R
Y
V
A
E
H
EDITION 2008
Produced by:
Publication Edited by:

Technical Application
Strada delle Cascinette, 424/34
B.U. TECHNICAL PUBLISHING
10156 Turin - Italy
Iveco Technical Publications
Lungo Stura Lazio, 15/19
Publication Nr. 603.93.721 - 2nd Edition 10156 Turin - Italy
Printed in Italy - 01/08
STRALIS AS/AT/AD EURO 4/5
Bodybuilders instructions
Print 603.93.721 - 2nd edition
Base - January 2008
UPDATE DATA
Section Description Page Revision date
2 Frame Paragraph 2.16 moved to chapter 5 January 2008
3 Structures 3-34: paragraph added 3.5.4.3 January 2008
4 Power take-off Full overhaul chapters 4.6 and 4.7 January 2008
4 Power take-off 4-17: Control unit added January 2008

Expansion Module (EM) (*)
5 Electronic subsystems 5-4: Cab Module (CM) January 2008

integrated in the Body Computer (BC) (*)
5 Electronic subsystems 5-8,5-9: connectors ST14A e ST14B January 2008
5 Electronic subsystems 5-40: note added to paragraph 5.4.8 January 2008
6 Exhaust systems with SCR Chapters 6.6 and 6.7 added. January 2008
Full overhaul chapter 6.5
(*) Specific parts only for OBD1 Phase 2.
NOTE The eighth digit of the PIC (Product Identification Code) indicates STEP 2 of the vehicle:
3-4-C-B Stralis AS
3-4-C Stralis AT/AD
Update data
Print 603.93.721 Base - January 2008

Update data
Base - January 2008 Print 603.93.721

Foreword
This manual contains instructions and data for fitting body structures/ancillaries and Vehicle modifications and is intended for
skilled and qualified personnel.
The bodybuilder is responsible for the design and fitting and any modifications necessary for the installation. The bodybuilder must
ensure full compliance with the requirements set out in this manual and with national and international regulations (Construction
and Use, and EEC Standards) in force.
Before starting any work make sure you are working form the latest Iveco Bodybuilders Instruction manual for the model. Make sure
that all safety equipment e.g. eye protection, hard hat, shoe, gloves etc are used. Check that all mechanical equipment e.g. lifts and
handling gear is in good working order and is used. Finally work on the vehicle in good conditions and ensure maximum safety at
all times.
Any change, modification or installations not covered by this manual and not expressly authorized in writing by IVECO will relieve
the latter of any responsibility and make, in particular, the vehicle warranty null and void.
For installations / modifications and general information not covered by this manual contact Iveco.
On completion of the installation e.g. body, crane, wheelbase modification the vehicle and systems must be checked to ensure vehicle
operation and safety is as designed by Iveco and has not been compromised. If a vehicle system needs to be set up i.e. engine control
for PTO installation then contact your local Iveco Service Department.
IVECO shafl not be responsible for any change, modification or fittings concerning the vehicle.
Due to continuing vehicle improvements and changes in regulations which cover or affect the vehicle, the information in this publica-
tion may not always be up to date.
If the bodybuilder has any queries regarding the information contained in this manual regarding the vehicle that is to be worked on
he should contact Iveco thbiveco@iveco.com before starting.
Symbols - Warnings
Danger to people:
failure to fully comply with these precautions can involve serious danger for personal safety.
Danger of serious damage to the vehicle

Partial or complete non observance of these precautions can cause serious damage to the vehicle and invalidate the
Iveco warranty.
Warning / Precaution:
! failure to fully comply with these precautions can result in serious danger to personal safety and damage to the vehicle
with the loss of the vehicle warranty.
This indicates the correct use of materials in order to make the vehicle as environmentally friendly as possible.
NOTE Indicates additional information.
Foreword

Page header and footer interpretation
Section number -
Vehicle type Section title
page number
Print Basic edition -

Chapter title
number month year
Foreword

INDEX OF SECTION
Section
General specifications 1
Chassis modifications 2
Building & Mounting the structures 3
Power Take-offs 4
Special instructions for electronic subsystems 5
Special instructions for -SCR- exhaust system 6
Index of section

Index of section

STRALIS AS/AT/AD Euro 4/5 GENERAL SPECIFICATIONS 1-1
Index
SECTION 1
General specifications
Page
1.1 Aim of bodybuilders instructions 1-3
1.2 IVECO “no objection” for changes and fittings 1-3
1.3 Liabilities 1-4
1.4 Guarantees 1-4
1.5 Request for a “no objection” 1-4
1.6 IVECO technical documents available by means of computer 1-5
1.7 Trademarks and Logos 1-5
1.8 Legal Provisions 1-5
1.9 Prevention of accidents 1-6
1.10 Choice of material to use: Ecology - Recycling 1-6
1.11 Vehicle delivery 1-7
1.12 Vehicles Identification 1-8
1.13 Dimensions and weights 1-9
1.13.1 General Specifications 1-9
1.13.2 Determining the Centre of Gravity of the Body and Payload 1-9
1.13.3 Observing the Permitted Weights 1-13
1.14 Instructions for the Correct Functioning of the Parts of the Vehicle and Accessibility for Maintenance 1-14
1.15 Quality System management 1-15
1.16 Vehicle maintenance 1-15
1.17 Conventions 1-16
Index
1-2 GENERAL SPECIFICATIONS STRALIS AS/AT/AD Euro 4/5
Index
Aim of bodybuilders instructions
1.1 Aim of bodybuilders instructions
The purpose of this publication is to provide data, specifications and instructions for the bodybuilding and conversion of an original
IVECO vehicle to ensure the functionality, safety and reliability of the vehicle and its components.
1.2 IVECO “no objection” for changes and fittings
Changes must be carried out in accordance with the requirements set out in the following guidelines.
The following may be carried out only with IVECO’s authorisation after submitting a copy (two for English Market) of the documenta-
tion required for technical evaluation of the proposed change (drawings, calculations, technical report etc.):
- wheelbase modifications, where the new wheelbase does not fall within the minimum and maximum wheelbase available within
the IVECO range for the same vehicle;
- work carried out on the braking system;
- work carried out on the suspension system;
- steering wheel modifications;
- changes to the stabiliser bars and suspensions;
- changes to the cab, cab supports, locking and tipping devices;
- changes to the intake systems, engine exhaust and SCR components;
- engine cooling system modifications;
- power unit and driving component modifications;
- work carried out on front and rear axles;
- fitting additional axles;
- fitting decelerator brakes;
- fitting power take-offs;
- changing the tyre dimensions;
- coupling device (hooks, fifth wheels) modifications;
- electric/electronic unit modifications.
The other modifications of fittings covered by the following standards and made in compliance with the same do not require specific
authorisation from IVECO. Any modification or fitting not covered by these standards shall, on the contrary, be authorized by IVECO
in advance.
Aim of bodybuilders instructions

Liabilities
1.3 Liabilities
The authorizations issued by IVECO concern solely the technical/conceptual feasibility of the modification and/or fitting to be
made on a genuine IVECO vehicle.
The bodybuilder is responsible for the:
- project of the modification or fitting;
- choice and features of the products used;
- workmanship of the modification or fitting;
- compliance of the project and its implementation with all the instructions provided by IVECO;
- compliance of the project and its implementation with all the current regulations in the country where the vehicle is registered;
- the operation, safety and reliability and in general the effective performance of the vehicle and also the effects that the changes
and the conversion may have on the performance and specifications of the vehicle.
1.4 Guarantees
The bodybuilder/chassis converter who has built the body or who has modified the chassis must guarantee that the work was
undertaken in a professional manner in full compliance with the specifications contained in this manual. IVECO reserves the right
to declare void its own warranties for the vehicles where:
- these specifications have not been adhered to or where unauthorised equipment was installed, or unauthorised modifications
were carried out;
- an unsuitable vehicle/model has been used for the required conversion or application;
- the specifications, standards or instructions issued by the Manufacturer for the flawless execution of the operations have not
been followed;
- original spare parts or components which IVECO has made available for specific conversions were not used.
Maintaining the functionality of vehicle components.

The effective operation of vehicle components, all component safety and running conditions, com-
pliance with national and international regulations (e.g. EC Directives) and accident prevention stan-
dards must be guaranteed in all permitted conversions and applications.
All our vehicles are covered by a warranty as laid down in the specific documents.
The bodybuilder must carry out operations at least in an equivalent manner.
1.5 Request for a “no objection”
The requests for approval or support to carry out work or make modifications or fittings shall be forwarded to the IVECO marke-
ting offices in charge.
To obtain the approval, the body builder shall provide adequate documents that illustrate the anticipated implementation, utilization
and conditions of use on the vehicle. The drawings shall highlight any item differing from the instructions contained in this manual.
The body builder shall submit the modification and/or fitting to the competent authorities for approval.
Liabilities
IVECO technical documents available by means of computer
1.6 IVECO technical documents available by means of computer
The following technical documents are available on the Internet at www.thbiveco.com:

- bodybuilder instruction manuals;
- specification sheets;
- chassis cab diagrams in .dwg and tiff formats;
- chassis diagrams in tiff formats;
- other specifications concerning the vehicle range.
1.7 Trademarks and Logos
Trademarks, nameplates and denominations must not be modified or displaced in relation to the original design. The appearance
of the vehicle must not be changed or modified.
The application of trademarks tied to the transformation or trim levels must be authorised by IVECO. They must not be applied
near to the IVECO tradenames or logos.
IVECO reserves the right to withdraw the tradenames and logos if the fitting or conversion fails to conform with requirements. The
bodybuilder accepts all responsibility for the entire vehicle.
Instruction for added assemblies

Where assemblies are added, the bodybuilder must provide the necessary service and maintenance instructions when the vehicle
is delivered.
1.8 Legal Provisions
On completing the vehicle, the bodybuilder/chassis converter must check the work (modifications, body + equipment etc.) to
ensure that the legal provisions required in the country of registration are observed (e.g. weights, dimensions, braking, noise,
emissions etc.). Information regarding these matters may be obtained from the competent Authorities or the IVECO Area Network.
The vehicles manufactured at our plant (except some versions for Extra-European countries) comply with the EC directives. Conver-
ted vehicles must also comply with these directives. The only permissible exception is granted where local type approval differs from
EC homologation.
IVECO technical documents available by means of computer

Prevention of accidents
1.9 Prevention of accidents
The structures and devices fitted to the vehicles must comply with the current regulations concerning
the prevention of accidents and safety regulations in force in the countries where the vehicle is to be
used.
All the precautions dictated by technical awareness must be adopted to prevent malfunction and functional defects.
Compliance with these regulations will be the responsibility of the manufacturers of the structures and devices.
Components such as seats, coverings, linings, protective panels etc. may present a potential fire hazard
! if they are exposed to an intense heat source.
They should be removed before working with welding equipment and flames.
1.10 Choice of material to use: Ecology - Recycling
Increasingly greater attention should be paid, at the study and design stage, to the choice of materials to be used.
This is especially the case as regards the aspects connected with ecology and recycling in the light of domestic and international
regulations that are constantly being developed in the sector.
In this connection:
- everyone must be aware of the prohibitions on using harmful or potentially hazardous materials, such as ones containing asbestos,
lead, halogen additives, fluorocarbons, cadmium, mercury, hexavalent chrome, etc.
- Use materials whose processing produces limited waste and that permit easy recycling after their first use.
- With composite synthetic materials, use components that are compatible with each other, envisaging also their possible utiliz-
ation with the addition of other salvaged components. Affix the markings required in compliance with the current regulations.
In order to comply with EC directive 2000/53 (ELVs), IVECO S.p.A. prohibits fitting parts containing
lead, mercury, cadmium and hexavalent chrome to vehicles (except for the departures referred to in
Attachment II of the above directive).
Prevention of accidents
Vehicle delivery
1.11 Vehicle delivery
Prior to delivering the vehicle, the body builder shall:

- verify that the work has been made correctly;
- perform vehicle and/or equipment set-up;
- check the operation and safety of the vehicle and/or equipment;
- prepare and deliver the necessary instructions for service and maintenance of the fitting and any additional units to the end custo-
mer;
- write the new data down on the special tags;
- confirm that the work carried out complies with the indications provided by the vehicle manufacturer and with all legal require-
ments;
- carry out the checks included in the ”IVECO Pre-Delivery inspection” list (available from the IVECO network) with regard to
the items affected by the work done;
- provide a guarantee for the modifications made;
- in the event that the connections originally provided with screws have been mounted and restored, the same screws must not
be used. In such an instance, and in the event that rivets have been replaced with screws, you must again check the tightness
of the connection after travelling approximately 500-1000 km, to ensure it is to the correct torque.
- measure the battery voltage. Ensure there is a minimum charge of 12.5 V. If the voltage reading is between 12.1 and 12.49 V,
recharge the battery (slow charge). If the voltage is less than 12.1 V, the battery must be scrapped and replaced with a new one.
Vehicle delivery
Vehicles identification
1.12 Vehicles identification
The commercial designation of IVECO vehicles is not the same as the type approval (homologation) designation. Two types
of commercial designation are shown below with the meaning of the codes used:
Cab Model Power Version Suspension

Range
CAB VERSIONS A S 2 6 0 S 4 2 Y / P S
TRACTOR A S 4 4 0 S 4 5 T X / P
/TN
/P
PTT-Cab versions /PT
AS
(n˚/10 → hung in ton) T /PS
/FP
AD STRALIS Engine power
PTC-Tractors X /FS
AT
(with semitrailers) Y
(n˚/10 → hung in ton)
(n˚ x 10 → HP) Z
EXTERNAL NAMEPLATE ON
VEHICLE
CAB RANGE VERSION MISSION
AS = Active Space T = Tractor GV = Bulky Goods

AT = Active Time X= 6x2C transport
AD = Active Day Y = 6x2P CM = Mobile Boxes
(Z= 6x4) LT = Low Tractor
RR = Rough Roads
HM = Heavy Mission
D = Delivery
CT = With Transporter
HR = Hub Reduction
SUSPENSION
/TN = 6x2P, mechanics with third fixed axle to twinned wheels

/P = 4x2, 6x4, 6x2P, air suspension at rear. 6x2P with single wheels fixed third axle
/PT = Only for 6x2P, air suspension at rear with twin wheels fixed third axle
/PS = Only for 6x2P, air suspension at rear with single wheels third axle, controlled steering
/FP = 4x2, 6x4, 6x2P, full air
/FS = Only for 6x2P full air with single wheels third axle, controlled steering
Vehicles identification
Dimensions and weights
1.13 Dimensions and weights
1.13.1 General Specifications
The dimensions and maximum permissible weight on the axles are indicated on drawings, on technical specifications and, in
greater details, on the official documentation issued by IVECO.
The kerb weights refer to vehicles with standard equipment. Special equipment may involve considerable modification to the weight
and its distribution on the axles.
Lights and rear-view mirrors positioning on our vehicles is designed for widths of 2,550 mm. This dimension may also be applied
to special body versions with a width of 2,600 mm (e.g. refrigerator vans).
Weighing the Chassis

As a result of production factors there may be a variation in weight of approx. 5%.
It is, therefore, advisable to determine the weight of the vehicle with its cab before fitting the body and equipment and establishing
their distribution on the axles.
1.13.2 Determining the Centre of Gravity of the Body and Payload
Positioning on longitudinal plane

To establish the location of the centre of gravity of the body and payload the following examples below may be used as guidelines.
The technical documentation specific to each model (chassis cab drawing) give the positions permitted with the vehicle in its standard
form. The weight and positioning of the single components of the vehicle are given in the chassis and weight distribution diagram.

Figure 1.1 Vehicles with 2 axles; vehicles with 3 axles with an equal load on the two
rear axles
Example to determine the position of the centre of gravity of the payload plus body
W1 ⋅ L
A = Rear axle or tandem mid axle L1 = Distance of centre of gravity from L1 =
W = Payload + body centre-line of rear axle W
W1 = Share of payload on front axle (or tandem centre-line)
W2 = Share of payload on rear axle (or tandem) L = Actual wheelbase W2 ⋅ L
respectively L1 = L -
W
Figure 1.2 Vehicles with 3 or more axles with a constant mass distribution ratio on
the two rear axles. For these vehicles the ”ideal” values of the wheelbase
and centreline between the axles, resulting from mass distribution, is de-
termined by the Manufacturer.
Example to verify compliance of admitted weight on the axles

W = Payload + body W x L1 Attention:
W1 =
W1 = Share of payload on front axle L On vehicles with three or more axles, with a variable mass distribution
W2 = Share of payload on rear axles ratio on the two rear axles depending on the load, the ”ideal” values of
W3 = Share of payload on first rear axle (L - L1) wheelbase and centreline between the axles will have to be calculated
W4 = Share of payload on second rear axle W2 = W x on the basis of the information given in the chassis cab diagram, or in the
L
L1 = Distance of centre of gravity relative specific documentation specially prepared by IVECO. In this way, for
calculated centreline (A - L2) special versions (e.g. cranes on rear overhang) it will be possible to deter-
L = Calculated wheelbase (ideal) W3 = W2 x mine the correct positioning of the centre of gravity of the equipment
A
L2 = Calculated centreline (ideal) and payload on the basis of the actual load (see point 5.4 in section 5).
A = Distance between rear axles W2 x L2
W4 =
A

In order to apportion the payload on the axles, it must be uniformly distributed except when the shape of the loading surface itself
entails a different distribution of the load.
As for equipment, the actual location of the centre of gravity is used.
When building bodies or containers, loading and unloading systems for the transported goods must be devised which preclude ex-
cessive variations in the distribution of the load and/or excessive loads on the axles, also giving the relevant instructions to the users.
The bodybuilder will also need to install suitable payload securing systems on the body so that transport can be made with the utmost
safety.
Figure 1.3
Uniform distribution of the load Non-uniform distribution of the load due to the
lack of rear overhang
Uniform distribution of the load Non-uniform distribution of th e load (beware of load on axles
and minimum ratio)

Height of the Centre of Gravity

The height of the centre of gravity of the chassis cab is given in the technical documentation specific to each model (chassis
drawing).
For testing the vehicle complete with superstructure, the bodybuilder must check that the height of the centre of gravity of the
equipment including the payload, or of the entire vehicle when fully loaded, falls within the maximum permitted values.
These limits are defined in compliance with the national or international regulations (e.g. as amended by the current EC braking
Directive) or requested by the Manufacturer to ensure good handling of the vehicle (e.g. transverse stability of the moving vehicle).
In order to comply with the current EC Directive, IVECO provides information for the various models (wheelbase and specific body)
on computer, regarding:
- height of centre of gravity of chassis cab (e.g. chassis cab diagram, braking data);
- maximum height of centre of gravity of complete vehicle at full load (e.g. national type-approval document);
- braking capacity of each single axle (e.g. braking data).
Figure 1.4
Verification with full load:
(Wv + Ws) . Ht − Wv . Hv
Ht = Wv . Hv + Ws . Hs Hs =
Wv + Ws Ws
Wv = Chassis cab vehicle kerb weight

Hv = Height of centre of gravity of chassis cab vehicle (laden condition)
Ws = Body and payload
Hs = Height of centre of gravity of body and payload in relation to ground
Wt = Vehicle weight when fully loaded
Ht = Height of centre of gravity of vehicle fully laden to gvw
To check the vehicle with its body but no payload, use above formula but for Ws use only the body kerb weight (The position for
Hv will depend on the load and deflection of the suspension).
The height of the centre of gravity indicated in Tabella 2.6 represents values which are not to be exceeded for each given equipment
level. These values have been calculated only in terms of the transverse stability of the vehicle and are applicable to a mid wheelbase.
Any other possible restrictive specification, e.g. braking regulation, should be taken into consideration.
The values given in Tabella 2.6 refer to the superstructure with fixed payload. In versions where the payload tends to move on side
(e.g. suspended loads, fluid loads etc.) especially when turning, higher dynamic stress is generated which makes the vehicle less stable.
This must be taken into consideration when providing vehicle operating instructions or for possible reduction in the height of the
centre of gravity.

Using Stabiliser Bars

Supplementary stabilising or anti-roll bars, where available, spring reinforcements or the application of rubber components (in
compliance with point 2.7) may increase the height of the centre of gravity of the payload which must be defined as each occasion
arises. The modification must be carried out after careful consideration has been given to the specifications of the version, to the
wheelbase and to the distribution of the cross-stresses acting on the suspension both at the front and at the rear of the vehicle.
It must be borne in mind that it is often advisable to modify the rear axle only since a modified front axle would give the driver a
false sense of stability making it more difficult to perceive the safety limits. Modification to the front axle may be made where the
load is positioned behind the cab (e.g. crane) or where the superstructures are very rigid (e.g. van conversion).
Exceeding the Limits
When transporting goods with an exceptionally high centre of gravity (e.g. machinery, indivisible cargo etc.) from a technical point
of view it is possible to exceed the values indicated in the table provided that the steering system of the vehicle is suitably adapted
to this condition (e.g. reduced speed, gradual changes on the steering wheel, etc.).
1.13.3 Observing the Permitted Weights
All limits indicated in our documentation must be adhered to. The load of the front axle is of particular importance under varying
load conditions, in order to ensure the correct steering characteristics on road surfaces of all types.
Particular attention must therefore be paid to vehicles with a weight which is concentrated on the rear overhang (e.g. cranes, tail-lifts,
centre axle trailers) and to vehicles with a short wheelbase and a high centre of gravity (e.g. silo vehicles, cement mixers).
When positioning the body and equipment, the loads must be correctly distributed transversally. For each wheel a variation in the
rated load (1/2 of the axial load) of 4% is permitted (e.g. admitted load on axle: 10,000 kg load admitted on each wheel: 4,800 to
5,200 kg) provided that the tyres permit it, without impairing braking or driving stability.
For vehicles with an added rear lift axle it must be remembered that, with the axle in the raised position, the effective wheelbase
is reduced, whereas the rear overhang is increased. It is therefore advisable that the centre of gravity of the body and payload is
located in front of the centre line of the driving axle. In addition to this it is not advisable to equip a vehicle which has its load concen-
trated at the rear, with a lifting device.
Apart from different specifications for specific individual vehicles, the following may be taken to be the minimum values for the front
axle:
- 20% of the total vehicle weight with uniformly distributed loads
- 25% of the total vehicle weight for loads that are concentrated on the rear overhang.
The rear overhang of the body must be built in strict observance of the permitted axle loads, the limitations in length, the positioning
of the tow hook and of the underride guard stipulated by the relevant regulations and legal requirements.
Variations in the Permissible weight

Special exceptions to the maximum permissible weight may be granted for particular applications for which, however, precise
limitations regarding the use will be imposed in addition to possible vehicle reinforcements.
Such exemptions, if they exceed the limits imposed by law, must be authorised by the Administrative Authority.
A reduction in admissible vehicle load (downrating) may require modifications on some parts, such as the suspension. In these cir-
cumstances, the necessary information may be supplied.
The request for authorisation must include:
- Vehicle type, wheelbase, identification number, designated use.
- Weight distribution on the axles (e.g. vehicles equipped with crane and body) including positions of the centre of gravity of the
payload.
- Proposals concerning the reinforcement of the vehicle components where necessary.

Instructions for the Correct Functioning of the Parts of the Vehicle and Accessibility for Maintenance
1.14 Instructions for the Correct Functioning of the Parts of the Vehicle
and Accessibility for Maintenance
As a rule, when modifying or installing any type of equipment, nothing must be altered which prevents the correct functioning
of assemblies and parts of the vehicle under all operational conditions.
For example:
- Ready access to all parts requiring inspection or maintenance and periodic servicing must be provided. In the case of closed body
types suitable opening doors must be provided.
- For tilting cabs, adequate space permitting tilting must be assured. In the case of structures which involve the space above the
driver’s cab, adequate space for the passage of intake air must be guaranteed (see 1.5).
Figure 1.5
1. Retain adequate room for tilting the driver’s cab - 2. Retain the free space above the gearbox (for tractors with semitrailers
consider the movement between tractor and semitrailer) - 3. Cab pivot point - 4. Min. distance to be met
- Service access to chassis/driveline components must be retained. For instance repairing the gearbox or clutch must be possible
without necessitating the removal of major components of the added structure.
- The cooling system (radiator cowling, radiator, air passages, cooling circuit etc.), fuel supply (pump position, filters, pipe diameter,
etc.) and the engine air intake must not be altered.
- The anti-noise panels must not be altered or moved in order to prevent changes in the approved noise levels of the vehicle.
Should it be necessary to make openings (e.g. for the longitudinal runner of the body to pass through) these must be properly
closed off using material with inflammability and soundproofing characteristics equivalent to those used originally.
- Adequate ventilation of the brakes and battery case (especially in the case of box bodies) must be guaranteed.
- The positioning of the mud-guards and wheel-arches must allow free movement of the rear wheels even when chains are being
used. Sufficient space must also be ensured with lifting axles. Some of our models have 3rd axle steering which also steers in
the raised position; and it is necessary to leave space for this function (see point 2.20).
- When the vehicle has been set up, for safety reasons, headlight attitude must be checked and adjusted as necessary. Perform
the adjustment according to the instructions provided in the user and maintenance manual.
- In the case of parts which are supplied loose (e.g. spare wheel, chocks) it will be the responsibility of the bodybuilder to position
and secure them in an accessible and safe manner in compliance with possible national regulations.
1.15 Quality System management
For some time IVECO has been promoting Quality System development and training for bodybuilders.
This is a requirement due not only to compliance with domestic and international regulations on product liability, but also the growing
demand for increasingly higher quality levels. The creation of new forms of organization in the various sectors and the quest for
increasingly more advanced levels of efficiency.
IVECO believes it essential for bodybuilders to be equipped and organised where the following are defined and available:
- organization charts for functions and responsibilities.
- Quality System.
- quality goals.
- technical design documentation.
- process and control phases with relevant resources.
- product improvement plan, obtained also with corrective actions.
- after sales service.
- staff training.
- manufacturer liability documentation.
1.16 Vehicle maintenance
In addition to making the necessary checks on the body/structure in keeping with customary working procedures, the bodybuil-
der shall perform the checks specified in the “IVECO pre-delivery inspection” list, which can be obtained from the IVECO network,
for the aspects affected by the modifications performed.
Convention
1.17 Conventions
In these bodybuilders instructions, the wheelbase is taken as the distance between the centreline of the first steering axle and
the centreline of the first rear axle (driven or non-driven). This definition differs from the definition of wheelbase in the CE Directives.
The rear overhang is taken as the distance between centreline of the last axle and the rear end of the chassis runner. For dimensions
A, B and t of the frame and subframe section please refer to the figure below.
Figure 1.6
91473
Convention
STRALIS AS/AT/AD Euro 4/5 CHASSIS MODIFICATIONS 2-1
Index
SECTION 2
Chassis modifications
Page
2.1 General instructions for chassis modifications 2-5
2.1.1 Specific Precautions 2-5
2.2 Painting and Rust Protection 2-7
2.2.1 Original components 2-7
2.2.2 Added or modified painted parts 2-9
2.2.3 Precautions 2-10
2.2.4 Max indicative height of center of gravity of payload in relation to transverse stability 2-11
2.3 Drilling the Chassis 2-12
2.3.1 Screws and nuts 2-12
2.3.2 Characteristics of the material to be used when modifying the chassis 2-13
2.3.3 Stresses on the chassis 2-14
2.3.4 Welding the Chassis 2-15
2.3.5 Closing of existing holes 2-17
2.4 Modifying the Wheelbase 2-18
2.4.2 Authorisation 2-18
2.4.3 Effects on the steering 2-18
2.4.4 Effects on braking 2-19
2.4.5 Recommended procedure 2-19
2.4.6 Chassis Stress Level 2-20
2.4.7 Cross Members 2-20
2.4.8 Changes to transmissions 2-20
2.5 Modifying the Rear Overhang 2-21
2.5.2 Reducing the Overhang 2-21
2.5.3 Increasing the Overhang 2-21
2.6 Installing a Towing Device 2-23
Index
2-2 CHASSIS MODIFICATIONS STRALIS AS/AT/AD Euro 4/5
Page
2.6.2 Traditional towing hooks 2-24
2.6.3 Towhook for mid-axled trailers 2-25
2.6.4 Lowered Rear Cross Member 2-27
2.6.4.1 Centre axle trailers: towing cross member in lowered and forward positions (short coupling) 2-35
2.6.4.2 Reinforcement of Standard Rear Cross Member 2-35
2.6.4.3 Tow hooks for Centre Axle Trailers 2-37
2.6.4.4 Remarks about the Payload 2-37
2.6.4.5 Increasing the Towable weight 2-38
2.7 Installing a Supplementary Axle 2-38
2.7.2 Chassis Frame Reinforcement 2-38
2.7.3 Installing a Rear Supplementary Axle 2-40
2.7.4 Steering Axles 2-41
2.7.5 Components and Suspension 2-41
2.7.6 Stabilisers 2-41
2.7.7 Connection to the Chassis Frame 2-41
2.7.8 Braking system for additional axle 2-42
2.7.9 Raise Device 2-42
2.7.10 Modifying the suspension 2-45
2.8 Modifying the Drive Line 2-43
2.8.1 Permitted lengths 2-44
2.8.2 Determining Driveshaft Positions 2-46
2.9 Modifications of the Engine Air Intake and Exhaust Syatem 2-49
2.9.1 Intake 2-49
2.9.2 Engine exhaust 2-49
2.10 Modification of the Engine Cooling System 2-50
2.11 Installation of a Supplementary Heating System 2-51
2.12 Installing an Air-Conditioning System 2-52
Index
Page
2.13 Cab Modifications 2-53
2.13.2 Roof Panel Modifications 2-53
2.14 Changing the Size of the Tyres 2-54
2.15 Modifications to the Braking System 2-56
2.15.2 Brake Pipes 2-56
2.15.3 Electronic braking system control devices 2-61
2.15.4 Taking air from the system 2-61
2.16 Electrical System: Modifications and Drawing-Off Power 2-62
2.17 Repositioning Parts and Mounting Auxiliary Assemblies and Equipment 2-62
2.18 Transporting hazardous goods ADR 2-65
2.19 Retarder installation 2-67
2.20 Modifications to the Rear Underrun 2-68
2.21 Rear Mudguards and Wheel Boxes 2-69
2.22 Mudflaps 2-70
2.23 Side Guards 2.71
2.24 Chocks 2-73
Index
Index
2222.2
General instructions for chassis modifications
2.1 General instructions for chassis modifications
Particular attention must be given to the following points:

- Welding to the bearing structures of the chassis is explicitly prohibited (with the exception of the items described at points
2.3.4, 2.4 e 2.5).
- Holes in the flanges of the side members are not permitted (except for the items described at point 3.4).
- Where riveted connections exist and can be modified as explained below, these can be replaced by flanged-head screws and
nuts of min. class 8.8 or by hex screws of the next greater diameter and self locking nuts. Screws greater than M14 must not
be used (max. diameter of hole 15 mm) unless otherwise specified.
- In cases where the original joints were detached and rejoined with bolts it is forbidden to reuse the same bolts. In this event
and when rivets are replaced with bolts, the bolt torque must be checked after the vehicle has been driven approximately 500
÷ 1.000 kms.
2.1.1 Specific Precautions
During welding, drilling, grinding and cutting operations near brake system pipes, and electri-
! cal cables, adopt the appropriate precautions for their protection. Remove them altogether
if necessary (observe the requirements set out under points 2.15.2 and 5.5).
Figure 2.1
91444

Take precautions concerning the alternator and the electrical/electronic components

In order to avoid damaging the diode rectifier, never disconnect the batteries (or open the isolator) when the engine is running.
If the vehicle has to be tow started make certain that the batteries are connected. Should it be necessary to charge the batteries,
disconnect them from the vehicle circuit.
In order to run the engine with external means and in order to avoid current peaks which might damage the electric/electronic
components, do not use the ”start” function in conjunction with external charge devices if such devices are equipped with this
function. Starting will have to be carried out only with the external battery trolley ensuring correct polarity.
Earth connections
As a general rule the original earth connections of the vehicle must not be changed. If it is necessary to move these connections
or to implement further earth points use the existing holes on the chassis as far as possible and:
- Remove, mechanically, and/or with an appropriate chemical product, the paint on the chassis side and on the terminal side creat-
ing a resting plane free from indentations or ridges.
- Apply appropriate high conductivity paint between the cable terminal and the metal surface (e.g. galvanizing paint IVECO Part
number 459622 by PPG).
- Connect the earth cables within 5 minutes from the application of the paint.
Do not use the IVECO standardised M1 (battery earth connection) M2, M8 (earth connection for started motor depending on the
driving position) points for the earth connections for control switches (e.g. sensor or low absorption devices).
With regard to the electronic devices, avoid linking earth connections between the devices; only use single wire earths with optimised
lengths (as short as possible).
Electric wiring
Stralis vehicles are equipped with an innovative electronic system called MUX. Before performing any
! operation on the electrical system, read section 5 “Special instructions for electronic subsystems”.
For further information regarding the braking and electronic system, refer to point 2.15 and 5.5.
List of technical guidelines and standards for correct installation of electrical cables in vehicle electronic systems
Power cables (+ direct type) must be fed on their own into corrugated piping (of appropriate diameter) and not together with other
smaller cables (signal and negative cables); they must be spaced a minimum distance of 100 mm apart (reference value = 150 mm)
from high heat sources (engine turbine, exhaust manifold, etc., ...). and a distance of at least 50 mm must be maintained from chemical
agent containers (batteries, etc.).
This rule also applies to the area around moving parts.
Cables that run through perforated or angled panels must be protected by screw-on adaptors for cables (in addition to the corru-
gated pipe).
The corrugated pipe must wrap fully around the entire cable and must be secured with a heat-shrink sleeve or using adhesive tape
to the plastic terminal caps. Collars securing the corrugated pipe cut along their length must not deform the pipe, otherwise the
cables could be laid bare or come into contact with the sharp corners of the corrugated pipe.
All connection terminals (+) of the above cables and also their terminals must be covered with plastic caps waterproof version, at
all points exposed to atmospheric ingress or where water builds up.
The fastening of the terminal on the clamps (including the earth clamps) must be protected against accidental loosening. For this
reason, it is necessary to apply an appropriate tightening torque if possible. In the case of multiple terminal connections, these must
be in a star configuration (but this connection method should be avoided if possible).
The relevant cable route must be supported by fastenings and collars spaced close together to prevent hanging cables. After repair,
outfitting or conversion work, restore the wiring harness to its original condition.
When connecting the frame and the tipper cab, check the wiring with the cab raised and tipped to detect and correct any abrasions
or tautness of the cables.

Painting and Rust Protection
2.2 Painting and Rust Protection
2.2.1 Original components
Table 2.1 shows the protection and painting classes required for original vehicle components. Table 2.2 shows classes for unpain-
ted or aluminium parts and Table 2.3 shows classes for painted parts.
Table 2.1 - Protection classes as for STD 18 - 1600 (Schedule I)

Class Features of the part Examples of the type of part
A Parts in direct contact with atmospheric agents Cab, rear view mirrors, cab fixing components
Chassis and related parts, including fixing. Components
B Parts in direct contact with atmospheric agents with and parts under the hood
mostly structural characteristics,
characteristics directly visible
B1 Rear and front axles
Parts in direct contact with atmospheric agents, not
C Engine and related parts
directly visible
D Parts not in direct contact with atmospheric agents Pedals, seat frames, fixing components, internal cab pillars
Table 2.2 - Various unpainted and/or aluminium parts and components

Class
Material Type of protection
A B - B1 C D
Stainless
- yes - - -
steel
DAC 500/8/PL DAC 320/5 - -
chemical coating GEO 321/8/PL (*) (1) GEO 321/5 (*) (1) - -
GEO 321/8/PM (*) GEO 500/5 (*) - -
FE/ZN 12 III - - yes yes
Ferrous - yes yes
FE/ZN 12 IV (*)
( ) -
Zinc treatment ((2))
FE/ZN 12 V - y
yes - -
FE/ZN 12 IV S (*) - yes - -
Anodizing yes yes yes yes
Aluminium
Painting yes - - -
(*) Hexavalent chromium-free
(1) I.S. 18-1101
(2) I.S. 18-1102

Table 2.3 - Painted parts as for STD 18 - 1600 (Schedule III)

Classes
Description of the cycle phase
A B (5) B1 C D
Mechanical surface cleaning (including Sand blasting - yes • - yes • yes •
the removal of burrs / rust and cleaningg Brushing yes •
off modified
d f d parts)) Sanding
Degreasing - - - yes • yes •
Phosphate degreasing
Pre treatment
Pre-treatment
Phosphating of the heavy iron yes •
Phosphating of the zinc yes
High thickness (30-40 μm) yes (1) yes (4) - yes (6) yes •
• •
Cataphoretic treatment
Low thickness (15-25 μm) yes (2)
Acrylic to finish (>35 μm) -
Bicomponent (30-40 μm) - yes (7) -
Anti rust
Anti-rust
Monocomponent (30-40 μm) - yes
Mono (130 °C) or bicomponent (30-40 yes (2) - - - -
Chip-resistant base
μm)
Mono (130 °C) or bicomponent (30-40 yes yes • - yes • yes •
μm)
Paint Powders (50-60 μm) yes (3) yes
Monocomponent at low temperature - - yes
(30-40 μm)
(1) = Cycle for two-coat preparation.
(2) = Cycle for three-coat preparation.
(3) = Alternative to the mono or bicomponent paint, only for cab parts (windscreen wipers, rear view mirrors, etc.)
(4) = Excluding parts that cannot be immersed in pre-treatment and paint baths, due to their geometry (air tanks), their large size (castings) or where this would
compromise their functionality (mechanical parts).
(5) = For ferrous steel or pre-coated fuel tanks, refer to Table 2.2.
(6) = Only parts fitted on the engine.
(7) = Parts that cannot be treated cataphoretically (4).
• = Alternative products and cycles for the same class, as long as they are compatible with the part being treated.
NOTE All components installed on chassis must be painted as per Sta Iveco 18-1600 Colour IC444RAL 7021
brightness 70/80 gloss.

2.2.2 Added or modified painted parts
All parts of the vehicle (cab, chassis, bodywork, etc.) which are added or subjected to modification must be protected from rust
and corrosion.
There must be no unprotected areas on ferrous materials.
Table 2.4 (painted) and Table 2.5 (unpainted) show the minimum treatments required for modified or added components when
it is not possible to provide the same protection as that used on IVECO original components. Different treatments are allowed
on condition that the same level of protection against rust and corrosion is guaranteed.
Never use powder enamels directly after degreasing.
Parts in light alloy, brass and copper must not be protected.
Table 2.4 - Added or modified painted parts

Class
Description of the cycle phase
A - B - D (1)
Mechanical surface cleaning (including the removal of burrs / rust
Brushing/sanding/sand blasting
and cleaning of modified parts)
Pre-treatment Degreasing
Anti-rust Bicomponent (30-40μm) (2)
Paint Bicomponent (30-40μm) (3)
(1) = Modifications to rear axles, front axles and engine (Classes B1 and C) are not allowed.
(2) = Preferably epoxy.
(3) = Preferably polyurethane.
Table 2.5 - Added or modified unpainted and/or aluminium parts
Class
Material Type of protection
A - B (1) D
Stainless steel -
yes
chemical coating -
Ferrous
Zinc treatment - yes
Anodizing yes yes
Aluminium
Painting - -
(1) = Modifications to rear axles, front axles and engine (Classes B1 and C) are not allowed.

2.2.3 Precautions
Suitable precautions must be taken to protect those parts whose preservation and operation could be damaged by paints such
as:
- rubber or plastic pipes for the air and hydraulic installations;
- gaskets, parts in rubber or plastic;
- flanges of the transmission shafts or power take-offs;
- radiators;
- shock absorber and hydraulic or air cylinder rods;
- drainage and bleeder valves (mechanical components, air tanks, cold starting heater plug pre-heating tanks etc.);
- fuel sediment filter;
- nameplates and logos.
With particular regard to the engine and its electric and electronic components, adequate precautions must be taken to protect:
- on the whole engine and vehicle wiring, including earth contacts;
- on all connectors on sensor/actuator side and wiring side;
- on all sensors/actuators, on flywheel, on flywheel rev sensor bracket;
- on the whole diesel fuel system pipes (plastic and metallic);
- on complete diesel fuel filter base;
- on control unit and control unit base;
- on the whole soundproofing cover inner side (injectors, rail, pipes);
- on common rail pump including regulator;
- on vehicle electric pump;
- on tank;
- on front belt circuit and relevant pulleys;
- on power steering pump and relevant piping;
- ECU’s fitted on the vehicle.
If the wheels are removed, protect the contact surfaces on the hubs, avoid increasing the thickness and especially avoid the build-up
of paint on the connecting flanges of the wheel disks and contact points of the fixing nuts.
Ensure that the disc brakes are adequately protected.
The electronic components and modules must be removed.
When the painting operation is to be completed by oven drying (max. temp. 80ºC), all parts which may
! be damaged by exposure to heat, must be removed.

2.2.4 Max indicative height of center of gravity of payload in relation to transverse stability 1)
Table 2.6
Base equipment
with anti roll bars Max indicative height of center of gravity
M d l
Models (including body or equipment) in relation to
Front Rear
the ground (mm)
1 2 1 2
AS/AD/AT 190 x x 2720
AS/AD/AT 190/P x x 2750
AS/AD/AT 260 Y/TN x x 2740
AS/AD/AT 260 Y/P, Y/PS x x x 2720
AS/AD/AT 260Z/P x x x 2830
AS/AD/AT 260/P x x x 2720
Notes:
1) = Values refer to the transverse stability of the vehicle, to hold present eventual other limitations takes from the national and international regulations in
force (es. braking)
x = with standard anti-roll bar
- = without anti-roll bar
SW = to request roll bar

Drilling the Chassis
2.3 Drilling the Chassis
When it is necessary to mount assemblies or auxiliary units on the chassis, as a general rule, the existing holes made at the factory
should be used.
Under no circumstances should the flanges of the supporting member of the vehicle be drilled unless in compliance with
the indications given in point 3.3.1.
In those cases (installation of shelves, brackets etc.) where it is necessary to drill new holes, they must be drilled on the vertical
web of the side member and must be carefully deburred and reamed.
Position and Size
The new holes must not be made in areas of high stress (such as supports for springs) and at variance with the cross-section
of the side member.
The diameter of the holes must be proportional to the thickness of the steel. Under no circumstances must this exceed 15 mm
unless otherwise specified. The distance from the centre of the hole to the edges of the side member must not be below 40 mm.
The centres of the holes must never be located at a distance of less than 45 mm from each other or in relation to the existing holes.
The holes must be staggered as shown in Figure 2.2. When moving spring support or crossmembers, the same drilling arrangement
must be used always maintain the original boring.
Figure 2.2
91445
2.3.1 Screws and nuts
In general, use connectors of the same type and class as those for similar fixings on the original vehicle (Table 2.7).
As a general rule, materials of class 8.8 are recommended. Class 8.8 and 10.9 screws must have been hardened and tempered. For
applications of diameter ± 6mm, stainless steel parts are recommended. Approved finishes are Dacromet and zinc coating, as detailed
in Table 2.2. A Dacromet finish is not recommended if the screws are to be subjected to welding. If space allows, use screws and
nuts with flanged heads. Use self-locking nuts. Nuts must be tightened using a torque wrench set to the correct torque setting for
the fixing.

Table 2.7 - Classes of resistance for screws

Tensile strength Yield point
Class of resistance Usage
(N/mm2) (N/mm2)
4 (1) Non-load bearing screws 400 320
5.8 (1) Low resistance screws 500 400
Medium resistance screws
8.8 (cross members, cleat plates, 800 640
brackets)
High resistance screws
10.9 (spring supports, anti-roll bars 1000 900
and shock absorbers)
(*) Do not use
2.3.2 Characteristics of the material to be used when modifying the chassis
When modifying the chassis of the vehicle, and in applications which reinforce the side members directly, the material used must
correspond in quality (Table 2.8) and thickness (Table 2.9) to that of the original chassis.
Should it not be possible to source materials of the thickness indicated, the next greater thickness may be used (e.g. 1 mm instead
of 6.1 mm).
Table 2.8 - Material to be used to modify the chassis

Tensile strength Yield point
Steel name A5 elongation
(N/mm2) (N/mm2)
IVECO FeE490
Europe S500MC 610 490 19%
Germany QStE500TM
Alternatively, just for rear overhang extension.
IVECO Fe510D
Europe S355J2G3
520 360 22%
Germany QSt52-3N
UK BS50D

Table 2.9 - Chassis section dimension and thickness

AxBxt longitudinal pitch
Model Wheelbase (mm)
section(See Figure 1.6)
AD/AT/AS 190 Up to 6300 289/199x80x6,7
AS260/FP/FS Up to 5100+1395 289/199x80x6,7
AS260 S/PT Only 5700, 6050 289x80x7.7
AS260 (6X4) 4500 289x80x7.7
IVECO recommends the following chassis extension pieces, available from the Spare Part Division are used for chassis extensions.
2.3.3 Stresses on the chassis
Do not exceed the following stress values under static conditions:
Table 2.10
Range Permitted static stress on the chassis (N/mm2) σ amm.
On road Off-road use
Stralis 150 100
When required by national regulations, the bodybuilder must check that the stress limits are not exceeded.
Welding activity will cause a deterioration in the characteristics of the material. Therefore, when checking the stresses in thermically-
modified zones, consider a reduction of approx. 15% of the resistance characteristics.

2.3.4 Welding the Chassis
Welding operations must only be carried out by specialist, trained personnel, using suitable equipment
! and in a perfectly workmanlike manner. Any intervention on the system not carried out as per instruc-
tions provided by IVECO or carried out by unskilled staff, might severely damage the on-board sys-
tems, thus adversely affecting vehicle operation safety and efficiency and causing damages not covered
by warranty.
Welding is permitted:
- When joining the sidemembers to extend or shorten the wheelbase or rear overhang.
- For the application of reinforcing L section flitch on a side member that is to be modified as detailed below (v. Figure 2.3).
Figure 2.3
91448
When arc welding, the instructions below must be followed in order to protect electric units and ECUs:
- before disconnecting power cables, check to ensure all electrical items are switched off;
- where an electric switch is installed (battery isolation switch) wait for cycle end;
- disconnect negative power pole;
- disconnect positive power pole without connecting it to ground and DO NOT short circuit it with negative pole;
- disconnect ECUs connectors, carefully and do not touch ECU connector pins;
- when welding within the electronic control devices, disconnect them from the vehicle;
- connect welding machine ground directly to the part to be welded;
- protect plastic pipes against heat sources and remove, if necessary;
- if welding near leaf springs or air springs protect against welding spatters;
- avoid electrode or gun contact with spring leaves;

Operations for welding preparation
As part of the procedure it will be necessary to remove the paint and deoxidise the parts of the chassis that are affected by the
welding operation as well as those parts which may have to be covered by possible reinforcements. When work has been completed
the modified part must be protected with adequate rustproofing (see point 2.2.2).
a) Cut the side members with a diagonal or vertical cut. (We recommend that the diagonal cut be used particularly for the section
between the wheelbase) Cuts are not permitted in areas in which the profile of the side member as well as the chassis width
change or in those where there is a high concentration of stresses (e.g. spring brackets). The cuts must not be made through
the holes present in the side member (see Figure 2.4).
Figure 2.4
YES
YES 91446
b) On the inner side of the side member give the parts that are to be joined a V-shaped chamfer of 60° along the entire length
to be welded (see Figure 2.5).
c) Arc weld in stretches using carefully dried basic electrodes. The recommended electrodes are:
For S 500 MC (FeE490: QStE 500TM)
Diameter of the electrode is 2.5 mm, current intensity approx. 90A (max. 40A for each millimetre of diameter of the electrode).
Using MIG-MAG welding use a welding rod with the same characteristics as the material to be welded (diameter 1 to 1.2 mm).
Recommended welding rod: DIN 8559 - SG3 M2 5243
gas DIN 32526-M21 or DIN EN 439
If FeE490 is used at very low temperatures, we recommend:
PrEN 440 G7 AWS A 5.28 - ER 80S - Ni 1
gas DIN EN439-M21
Avoid current overloading. Welding must be free from marginal cuts and waste material.
d) Repeat the operation on the reverse side by welding as detailed in point c).
e) Allow the side members to cool slowly and uniformly. Cooling by air, water or other means is not permitted.
f) Remove excess material resulting from the welding operations by grinding.

Figure 2.5
91447
g) On the inner side reinforcing L-section flitches should be applied. These should be made of steel and have the same characteris-
tics as the steel used for the chassis. The minimum dimensions are given in Figure 2.3.
The reinforcements may only be fixed to the vertical web of the side member using welding beads, plug welds, bolts or rivets
(Huck rivets may also be used).
The cross-section and the length of the weld bead, the number and distribution of the plug welds, bolts or rivets must be ad-
equate to transmit the bending and shearing moment of the section.
2.3.5 Closing of existing holes
If, when making new holes, the existing holes are found to be too close (see Figure 2.2) these may be closed up by welding. To
ensure the success of this operation the outer edge of the hole should be chamfered and copper plate used for the inner part.
For holes with a diameter of over 20 mm, chamfered plugs may be used, welded on both sides.

Modifying the Wheelbase
2.4 Modifying the Wheelbase
Any change to the wheelbase affecting the electrical circuits and/or entailing a relocation of the electri-
! cal/electronic components must be approved and performed according to the instructions provided
in chapter 5.
As a rule, for each vehicle, modification to the wheelbase must be carried out on the standard wheelbase above or closer to
the new wheelbase required.
The measurements given in the written authorisations will apply in all cases particularly for extensions made to the longest standard
wheelbase.
Frame cutting must be performed according to the indications given at point 2.3.4. Whenever permitted by the body size, wheelbases
should be made equal to those planned in our production. This enables the original transmission shafts and previously defined cross-
member positions to be used.
When extending a wheelbase beyond the production longest planned, the vehicle used must have the longest production wheelbase
to ensure the correct thickness side members are used. Particular care must be taken to comply with the limits set by national regula-
tions particularly with regard to the limits for overall dimensions (where specified). Use only material shown at point 2.3.2.
2.4.2 Authorisation
The alteration of the wheelbase for the 4x2 versions is permitted without specific approval by IVECO in the following cases:
- If the wheelbase is to be lengthened and the new value is still within the standard range of length with the same side member
section. These sizes are given in the specific technical documentation or in Table 2.8 and Table 2.9.
- If the wheelbase is to be shortened without falling below the standard minimum values established for each model.
Provided the chassis converter gives sufficient guarantees from the technological and control point of view (qualified personnel,
adequate operating processes, etc.).
For the 6x2 and 6x4 versions the wheelbase may only be modified following specific approval by IVECO.
Conversion must be carried out performed in compliance with these instructions by making the necessary changes and adjustments
and taking the appropriate precautions (e.g., determining whether ECU parameters need updating, rearranging the exhaust pipes,
ensuring compliance with specific load limits on the rear axle, etc.), by taking into due account the requirements specified for the
original wheelbase lengths.
2.4.3 Effects on the steering

Generally, lengthening the wheelbase has a negative effect on the steering.
Whenever national regulations require it, the limits on the overall dimensions must be observed as well as the limits concerning
the effort applied on the steering wheel and the relevant operation times (e.g. ECE - R 79/01 standard or current EC Directive).
Tables 2.11 contain, the wheelbase extension limits for the various models, with series drive, at max load admissible on front axle
and with tires admissible on vehicle.
Should vehicles with longer wheelbase be needed, for special applications, it will be necessary to fit various devices aimed at improving
the steering characteristics such as a reduction in the maximum permitted load on the front axle or the installation of wheels and
tyres with shorter kingpin offset values (Table 2.17).
The fitting of an additional pump and a dual circuit power steering unit, if not immediately available, will require authorisation and
must only be installed by an authorised workshop.

2.4.4 Effect on braking

Generally, shortening the wheelbase has a negative effect on braking characteristics.
Table 2.11 gives the wheelbase alteration limits. Ask an authorised IVECO dealer for the conditions (brake cylinder, minimum tare
settings see section, technically permitted masses, tyres, height of centre of gravity) under which these values are permissible.
Table 2.11 - Maximum permitted wheelbase lengthening depending on the load on the front axle and tyre dimensions
(ECE - R79/01 regulation and EG/70/311)
Max wheelbase value

Max. load on front axle
between 1st steering Kingpin offset Steering wheel
Models (observe tyre carrying
axle and 1st driving (mm) dia. (mm)
capacity)
axle (mm)
AS/AD/AT 190 8000 6050 120 470
(without CM)
AS/AD/AT 190/FP-CM 8000 5700 120 470
8000 6700 120 510
AS/AD/AT 260 Y/P, Y/FP 8000 6050 120 470
(without CM)
AS/AD/AT 260 Z/P - HM 8000 6050 120 470
AS/AD/AT 260 Y/FP -CM 8000 4500 120 470
8000 5100 120 510
AS/AD/AT 260 Y/PS, Y/FS 7500 5700 120 470
7500 6050 120 510
(with CM) 8000 5700 120 470
AS/AD/AT 440TX/P (E5) 7500/7500 3140 120 470
AS/AD/AT 260XP 7500/7500 3140 120 470
For tyre type see Table 2.17.
2.4.5 Recommended procedure

To ensure the success of the conversion proceed as follows:
- Arrange the vehicle so that the chassis is perfectly level, using the appropriate stands.
- Disconnect the propeller shafts, the braking system pipes, the wiring harness and any equipment that might prevent the work
being carried out correctly.
- Identify the reference points on the chassis (e.g. pilot holes, suspension supports).
- Mark the reference points with a light line of punch marks on the top flange on both side members after ensuring that their joining
line is perfectly at right-angles to the longitudinal axis of the vehicle.
- When re-positioning the spring hanger brackets, identify the new position using the reference marks made previously.
Check that the new measurements are identical between the left and right sides. Differences no greater than 2 mm should
emerge from diagonal checking of the lengths less than 1,500 mm.
Unless another tool is available, make new holes by using the supports and gussets of the cross members as a template.
Fix the supports and cross members with rivets or bolts. If using bolts, fix the supports by reaming the holes and using class 10.9
calibrated bolts with nuts equipped with a device that prevents them from working loose. When space permits it use flanged-head
screws and nuts.
- If cutting the chassis, make a second line of reference points so that the area affected by the modification is included between
these and the previous points (in any event ensure a distance of not less than 1500 mm. measured when the work has been
completed). Inside these two reference lines make points to mark out the area of the cut then proceed as indicated in point
2.3.4.
Before welding, ensure that the side members, including any added portion, are perfectly aligned and take measurements on
both sides and diagonally to check, as previously described. Fit the reinforcements as instructed at point 2.3.4.

Further indications
- Protect the surfaces from oxidation as described in point 2.2.2.

- Restore the electrical and braking systems as described in points 2.15 and 5.5.
- For changes to the drive line follow the instructions given in point 2.8.
2.4.6 Chassis Stress Level
When lengthening a wheelbase, in addition to local reinforcement on the side member joint, the bodybuilder must provide suffi-
cient reinforcements to achieve the section moduli of the side member section no lower than that designed by IVECO for the same
wheelbase or for next size up. Alternatively, when permitted by local regulations, larger subframe sections can be used.
The body builder shall verify that such stress is not greater than the one of the chassis with the original wheelbase, by assuming an
evenly distributed load and the chassis being considered as a beam resting on the suspension supports. In any case, more restrictive
limits (if any) set by the national standards shall be complied with.
When extending out from the longest original wheelbase the reinforcements must depend on the length of the extension, the type
of body built and the use to which the vehicle is to be put.
2.4.7 Cross Members
The necessity of applying one or more additional cross members depends on the length of the extension, the location of the
transmission shaft support, the welding area, the introduction points of the forces produced by the body and the condition under
which the vehicle is to be used.
Any supplementary cross members must have the same features as those already existing (flexural strength, torsional strength, quality
of the material, connection to the side members, etc). In Figure 2.6 shows an example of the application. A cross member is mandato-
ry for any extension over 600 mm.
As a general rule the distance between the two cross members must not be greater than 1000 to 1200 mm.
The minimum distance between two cross members must not be less than 600 mm, particularly for heavy-duty and off-road use;
this limit does not apply to the ”lightweight” transmission support cross member.
Figure 2.6
91449
2.4.8 Changes to transmissions
See chapter 2.8 for admissible changes.

Modifying the Rear Overhang
2.5 Modifying the Rear Overhang
In modifying the rear overhang it must be borne in mind that such modification entails changes in the distribution of the payload
on the axles relative to the loads established by IVECO (see point 1.13). The limitations established by national laws must also be
respected as well as the maximum distance from the rear edge of the body and the ground clearance prescribed for the tow hook
and the underrun bar. The distance from the extremity of the chassis to the rear edge of the body must not, as a general rule, exceed
350 to 400 mm.
Should the bolted rear cross member be re-positioned, the same standard type of connections should be maintained (i.e. number
of screws, dimensions, class of resistance).
When re-positioning rear cross members fastened by rivets, these can be replaced by flanged nuts and bolts with same diameter
or by class 8.8 hexagonal-headed screws with the next largest diameter. Use self-locking nuts (do not use bolts with a diameter
larger than M14).
When the installation of a tow hook is planned an adequate distance (approximately 350 mm) must be left from the rear cross
member to the next nearest cross member for mounting and removing the tow hook wherever necessary.
If the modifications are carried out competently and in compliance with the specifications contained in this manual, the towable
weight originally established may be retained. In any case responsibility for the work rests with those who have carried it out.
Authorisation
Authorisation from IVECO is not required, if the frame is extended at the rear, or is shortened to the minimum value admissible
for each model as standard, provided that this is done according to the instructions given in this manual.
If it proves necessary modify the length of the electrical circuits, see chapter 5 “Special instructions for
! electronic subsystems”.
2.5.2 Reducing the Overhang
If the rear overhang of the chassis has to be reshortened, the last cross member must be moved forward.
If, when reducing the overhang, the rear cross member is found to be too close to an existing cross member, the latter must be
removed if it does not affect the suspension supports.
2.5.3 Increasing the Overhang
Various methods of increasing the length are given in Figures, 2.7 and 2.8.
The frame may be straight cut. The minimum dimensions of the reinforcements the are to be fitted to the modified section are given
in Figure 2.3.
Figure 2.7 shows a typical method of extension for increases of 300 to 350 mm. In this case the reinforcing L-bars, which also serve
to connect the cross member and the chassis frame, must be of the same thickness and width as the original gusset plate. The connec-
tion of the cross member and the plates, originally achieved with rivets, may be made with class 8.8 bolts with the next larger diameter.

In those cases where the joint between the cross member and the gusset plate is made by means of a weld, it is permissible to
join the gusset plate to the reinforcement by welding (see Figure 2.7).
When the increase exceeds 350 mm, Figure 2.8 shows the procedure to be used.
Figure 2.7
91454
1. Added portion - 2. Reinforcing runner - 3. Reinforcing runner (alternative solution) - 4. Original rear cross member
Figure 2.8
91455
1. Added portion - 2. Reinforcing runner - 3. Original rear cross member - 4. Supplementary cross member (if necessary)
So will be necessary to examine on a case by case basis, the feasibility of installing a supplementary cross member to give the frame
sufficient torsional rigidity. Adding a supplementary cross member with the same properties as the standard production cross mem-
ber is necessary whenever the distance between two cross members is greater than 1200 mm.

Installing a Towing Device
2.6 Installing a Towing Device
Without prior authorisation, the installation of a tow-hook is permissible only on those cross members which are intended for
that use and on those vehicles which IVECO has intended for towing a trailer.
The subsequent installation of a tow hook in vehicles for which the installation of a tow hook was not originally contemplated, must
be authorised by IVECO.
In addition to the permissible towing weight, the authorisation will specify all other possible specifications that are to be adhered
to such as the use of the vehicle, the transmission ratio, the type of braking system as well as possible specifications concerning
reinforcements to be applied to the rear cross member or the necessity for employing specially intended cross members.
In trailers with one or more axles close together (centre axle trailers), considering the stress resulting in particular from the vertical
dynamic load to which the rear cross member is subjected, the instructions given in point 2.6.4 must be taken into account.
The tow hook must be appropriate for the permitted loads and of the type approved by national laws.
! Since tow hooks are important to vehicle driving safety (in some countries they must be specifically
certified) they must not be modified in any way.
When mounting the tow hook to the cross member, the specifications of the hook manufacturer as well as the limitations imposed
by current standards - such as minimum space required for the brake and electrical connections the maximum distance between
the swivel hook axis and the rear edge of the body - must be respected.
This may vary as a function of national standards. In the European Community a maximum of 420 mm can be reached. If higher
values are required, check the EC Directive for the conditions to be able to accomplish this.
Should the fixing holes in the flange of the coupling hook not match the holes in the rear towing crossmember of the vehicle then
in certain cases re-drilling may be authorised in specific cases after applying appropriate reinforcements.
It is the bodybuilder’s responsibility to ensure that no part of the body or structure creates a hazard or impairs the maneuverability
of the trailer.
The trailer drawbar must be free to move unobstructed.

2.6.2 Traditional towing hooks
Choice of hook for traditional trailers
The reference dimension for choosing the type of hook is defined by value D calculated as defined below.
Figure 2.9
116773
Free area for towing hooks
When selecting the appropriate hook and for the use of reinforcements for the rear cross member (where necessary), the effect
of the horizontal forces produced by the weight of the tractor and trailer must be taken into account in accordance with the following
formulas:
TxR
D = 9.81 x
T+R
D = Representative value of the hook class (kN).

T = Maximum weight of tractor, in t.
R = Maximum weight of trailer, in t.

2.6.3 Towhook for mid-axled trailers
When using trailers with central axles or heavy single-axled trailers with enormous support loads (e.g. while braking or due to
vehicle vibration caused by road surface irregularities), the final crossmember is subject to additional twisting stress and the bending
moment on the protruding part of the frame is higher.
The towed load allowed for this type of trailer is therefore lower than that of normal trailers with a steering drawbar (see table 2.12).
For vehicles with very protruding crossmember or mid-axled trailers with high towed loads, a frame installation section (see table
2.12) that is sturdier than the one specified for this type of construction may have to be used.
On trailer with a fixed towbar, the installation frame must be fastened to the vehicle frame from the edge of the frame to the begin-
ning of the first rear axle suspension via the end blocks (replace consoles with end blocks or add more end blocks, see figure 2.12).
The towhook holes on the different towing terminal crossmembers available for most vehicles (for specific orders or as a conversion
product) correspond to a given attachment size.
For different towing terminal crossmembers, the towing loads shown in table 2.12 may generally be type approved for mid-axled
trailers provided the vehicle type is not subject to legal restrictions (e.g. engine power) or other construction units (e.g. transmission
unit, braking system).
For this reason, the values shown in table 2.12 must be confirmed in any case in writing by the frame manufacturer (e.g. in the type
approval certificates, in the manufacturer’s certification).
The value of the maximum (static + dynamic) vertical load transmitted by the trailer to the hook can be determined more accurately
through the following ISO formula:
Fv = a · x2/l2 · C · 0.6 + S
Fv = Max vertical load (static + dynamic) transmitted by the trailer to the tow hook (kN)
a = Vertical acceleration in the drawbar/towing hook coupling area; depending on the rear suspension of the tractor for semi-
trailer, use the following values:
- a =1.8 m/sec2 for vehicles with pneumatic suspension (or equivalent)
- a =2.4 m/sec2 for vehicles with other suspension types

x = Total length in mms of the loading area of the trailer (m).
l = Length of the trailer wheelbase (distance between drawbar towing eye centre and axle centre or trailer axle centre line)
in m.
C = Total weight of trailer, R, minus the static load applied S (all values expressed in tons).
S = Static support load (kN).
0,6 = Deceleration factor.

Figure 2.10
Chassis reinforcement for centre axle trailers
102183
1. Combined reinforcement - 2. Shear resistant connections (cleat plates) - 3. Subframe longitudinal runner -
4. Vertical load on tow hook
Table 2.12
Max. vertical loads permitted on hook
Dimensions of flange (mm) (kg) Maximum towable weight (kg)
(hook class) Total load * for centre-axle trailers R
Static S
(static+dynamic) Fv
120x55 (G135
( or G3)) 400 1130 4500
650 1690 6500
140x80 (G140 or G4) 900 2340 9000
G150 950 2470 9500
G5 1000 2960 12000
160x100 G6 1000 4040 18000
81 G5 1000 4400 20000
700G61 1000 5120 24000
* Indicative values determined according to ISO/TCC22/SCI5/WG4 Annex A through the following formula Fv = 3 × C × 0.6 + S (see following page)

2.6.4 Lowered Rear Cross Member
If the type of trailer used requires that the tow hook be positioned lower than originally intended, IVECO may issue authorisation
for the original cross member to be lowered or for an additional cross member (of the original type) to be fitted in a lower position.
Figures. 2.11 and 2.12 give some examples of how this is done.
The installation of the new cross member in its new position must be carried out in the same manner as before, using the same
type (diameter and class) of bolt.
Figure 2.11
91456
1. Original rear cross member - 2. Gusset - 3. Upside-down gusset - 4. Connecting angle piece
The thickness of the outer reinforcing angles must not be less than the thickness of the side members of the vehicle. They must
cover a length which is at least 2,5 times the height of the side member itself (maximum 600 mm) and be made of material with
the properties indicated in point 3.1.1. The angles are to be attached to the web of the side members using all the bolts joining the
cross member to the frame, integrating them with the other bolts so that, as a result of their number and location, they will take
into account the greater moment transmitted. As a general rule, when the cross member is lowered by an amount equivalent to
the height of the side member, the number of bolts is increased by about 40%.
When an additional cross member is installed (see Figure 2.12) a central joining plate with a thickness commensurate with that
of the cross members, must be employed.
A device to prevent the bolts from loosening must be adopted for the joints.

Figure 2.12
Version for chassis with long overhangs
Version for chassis with short

overhangs
91457
1. Original rear cross member - 2. Connecting angle piece - 3. Connecting plate - 4. Gusset plate -
5. Pressed steel channel sections (same size as chassis) - 6. Space for rear sprung support
Assurance should be given that the movements between the tow bar and vehicle conform to current regulations. As a general rule,
the original towable mass can be confirmed by IVECO. In any event the responsibility for the work carried out will rest with the
bodybuilder.
The vehicle must be presented for inspection if local government regulations require it.
In Figure 2.12 shows an example of a lowered supplementary cross member.
When this solution is applied to short rear overhang vehicles, the external connecting plates must conform to the arrangement
described in Figure 2.12. Should the brackets of the underrun bar be modified, following the lowering of the rear cross member,
the new version will be equivalent to the original in terms of attachment, strength and stiffness and the positioning of the lights
checked for compliance with the standards (local standards where applicable).

Table 2.13 - Longitudinal runner profiles of the subframe for centre axle trailers
Towable weight (R) static load on towhook (S) to centre axle (kg)
R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
Models Wheel Max. S≤ 950 S≤ 1000 S≤ 1000 S≤ 1000 S≤ 1000 S≤ 1000 S≤ 1000 S≤ 1000
body
(Chassis section) base Section modulus for each longitudinal section of subframe Wx (cm3) depending on the
overhang
(mm) (mm) material yield limit (N/mm2)
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
3800 970 - - - - - - - - - - - - - - - -
3800 1195 - - - - - - - - - - - - - - - -
3800 1825 - - - - - - - - 46 - 46 - 46 - 46 -
4200 970 - - - - - - - - - - - - - - - -
4200 1195 - - - - - - - - - - - - - - - -
4200 2050 - - 46 - 46 - 46 - 46 46 46 46 46 46 46 46
4500 1780 - - - - 46 - 46 - 46 - 46 - 46 46 46 46
4800 2455 46 - 46 46 46 46 46 46 57 46 89 46 89 46 105 46
AD AT 190,
190
5100 1555 - - - - - - - - 46 - 46 - 46 - 46 -
115 t rear
5100 1960 46 - 46 - 46 - - 46 46 46 46 46 46 46 46 46
289/199x80x6 7
289/199x80x6,7
5100 2185 46 - 46 46 46 46 46 46 46 46 57 46 74 46 89 46
5100 2365 46 46 46 46 46 46 57 46 57 46 89 46 89 46 105 46
5500 2185 46 - 46 46 46 46 46 46 57 46 57 46 74 46 89 46
5700 2185 46 46 46 46 46 46 46 46 57 46 74 46 89 46 89 46
6300 2005 46 - 46 46 46 46 46 46 46 46 57 46 57 46 74 46
6300 2365 46 46 46 46 57 46 74 46 89 46 105 46 105 57 119 57
6300 2770 57 46 89 46 105 46 105 57 119 74 150 89 173 105 173 105
6700 3400 46 46 46 46 74 46 74 46 89 46 105 46 105 74 150 74
3800 970 - - - - - - - - - - - - - - - -
3800 1195 - - - - - - - - - - - - - - - -
3800 1825 46 - 46 - 46 46 46 46 46 46 46 46 46 46 57 46
4200 970 - - - - - - - - - - - - - - - -
4200 1195 - - - - - - - - - - - - - - - -
4200 2050 46 46 46 46 46 46 57 46 57 46 74 46 89 46 105 46
4500 1780 46 - 46 46 46 46 46 46 46 46 46 46 57 46 57 46
4800 2455 74 46 89 46 105 57 105 57 135 74 150 89 173 89 173 105
AD AT 190
5100 1555 46 - 46 - 46 - 46 - 46 - 46 46 46 46 46 46
13 0 t rear
13.0
5100 1960 46 46 46 46 57 46 57 46 74 46 89 46 89 46 105 46
289/199x80x6 7
289/199x80x6,7
5100 2185 57 46 74 46 89 46 89 46 105 46 105 57 119 57 135 74
5100 2365 74 46 89 46 105 46 105 57 119 74 150 89 173 89 173 105
5500 2185 57 46 89 46 89 46 105 46 105 57 105 57 119 74 150 89
5700 2185 57 46 89 46 89 46 105 46 105 57 119 57 135 74 150 89
6300 2005 46 46 57 46 74 46 89 46 89 46 105 46 105 57 105 57
6300 2365 89 46 105 57 119 57 135 74 150 89 173 89 173 105 173 105
6300 2770 150 89 173 89 173 105 173 105 245 119 245 150 245 173 245 173
6700 3400 105 46 105 74 150 74 150 74 173 89 208 105 208 105 245 105

Table 2.13 - (continued) Longitudinal runner profiles of the subframe for centre axle trailers
R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
body
overhang
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
3800 1847 - - 46 - 46 - 46 - 46 - 46 46 46 46 46 46
4200 1217 - - - - - - - - - - - - - - 46 -
4200 2072 46 - 46 - 46 46 46 46 46 46 46 46 46 46 57 46
4500 1307 - - - - - - - - 46 - 46 - 46 - 46 -
4500 1802 46 - 46 - 46 - 46 46 46 46 46 46 46 46 46 46
4800 2477 46 46 46 46 46 46 57 46 74 46 89 46 105 46 105 57
5100 1577 46 - 46 - 46 - 46 - 46 46 46 46 46 46 46 46
AS 190S /P,/FP,/FP-CM 5100 1982 46 - 46 46 46 46 46 46 46 46 57 46 57 46 74 46
11.5
5 t rear
ea 5100 2207 46 46 46 46 46 46 57 46 57 46 74 46 89 46 105 46
289/199x80x6,7
, 5100 2387 46 46 46 46 57 46 57 46 89 46 89 46 105 46 105 57
5500 2207 46 46 46 46 46 46 57 46 74 46 89 46 89 46 105 46
5700 1982 46 46 46 46 46 46 46 46 57 46 57 46 74 46 89 46
5700 2207 46 46 46 46 57 46 57 46 74 46 89 46 105 46 105 57
6300 2027 46 46 46 46 46 46 57 46 57 46 74 46 89 46 89 46
6300 2387 46 46 57 46 74 46 89 46 105 46 105 57 119 57 135 74
6300 2792 74 46 89 46 105 57 119 57 135 74 173 89 173 105 173 105
6700 3422 46 46 46 46 74 46 74 46 74 46 89 46 105 57 105 74
3800 1847 46 46 46 46 46 46 46 46 57 46 74 46 74 46 89 46
4200 1217 - - 46 - 46 - 46 - 46 - 46 - 46 - 46 46
4200 2072 46 46 57 46 74 46 89 46 89 46 105 46 105 57 119 57
4500 1307 46 - 46 - 46 - 46 - 46 46 46 46 46 46 46 46
4500 1802 46 46 46 46 57 46 57 46 74 46 89 46 89 46 105 46
4800 2477 89 46 105 57 119 57 135 74 150 89 173 89 173 105 173 105
5100 1577 46 46 46 46 46 46 46 46 46 46 57 46 57 46 74 46
AS 190S /P,/FP,/FP-CM 5100 1982 57 46 74 46 89 46 89 46 105 46 105 57 105 57 119 74
13.0
3 0 t rear
ea 5100 2207 89 46 89 46 105 46 105 57 119 74 135 74 173 89 173 89
289/199x80x6,7
, 5100 2387 89 46 105 57 119 57 135 74 150 89 173 89 173 105 173 105
5500 2207 89 46 105 46 105 57 119 57 135 74 150 89 173 89 173 105
5700 1982 57 46 89 46 89 46 105 46 105 57 105 57 119 57 135 74
5700 2207 89 46 105 46 105 57 119 57 135 74 150 89 173 89 173 105
6300 2027 74 46 89 46 105 46 105 57 105 57 119 74 135 74 150 89
6300 2387 105 57 119 74 135 89 173 89 173 105 173 105 173 105 208 119
6300 2792 173 89 173 105 173 105 173 119 245 135 245 150 245 173 245 173
6700 3422 89 46 105 57 105 74 150 74 150 74 173 89 208 105 208 105

R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
body
overhang
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
3805 1757 46 46 46 46 46 46 46 46 57 46 74 46 74 46 89 46
4200 2117 74 46 89 46 89 46 105 46 105 57 119 57 119 74 150 89
4500 2072 74 46 89 46 105 46 105 46 105 57 119 57 135 74 150 89
AS 260 S .. Y/PT
4800 1712 46 46 57 46 74 46 74 46 74 46 89 46 105 46 105 57
19 0 t rear
19.0
4800 2072 89 46 89 46 105 46 105 57 119 57 135 74 150 89 173 89
289/199x80x6 7
289/199x80x6,7
5100 1802 74 46 74 46 74 46 89 46 105 46 105 46 105 74 105 74
5700 2432 105 46 105 74 150 74 150 74 173 74 208 89 208 105 208 105
6050 2657 150 74 150 74 173 89 208 105 208 105 245 105 245 105 286 150
3805 1757 57 46 74 46 74 46 74 46 89 46 105 46 105 57 105 74
4200 2117 105 46 105 57 119 57 135 74 150 89 173 89 173 105 208 105
4500 2072 105 46 105 57 119 74 150 74 150 89 173 89 208 105 208 105
AS 260 S .. Y/PT
4800 1712 74 46 89 46 105 46 105 57 105 74 135 74 150 74 150 74
20 0 t rear
20.0
4800 2072 105 57 119 74 150 74 150 89 173 89 208 105 208 105 208 105
289/199x80x6 7
289/199x80x6,7
5100 1802 105 46 105 57 105 74 105 74 150 74 150 74 173 74 208 89
5700 2432 150 74 208 89 208 105 208 105 245 105 245 135 286 150 286 150
6050 2657 208 105 245 105 245 105 245 150 286 150 286 150 317 173 343 208
3805 1757 89 46 105 46 105 57 105 74 135 74 150 74 150 74 173 89
4200 2117 150 74 150 89 173 89 208 105 208 105 208 105 245 105 245 119
4500 2072 150 74 173 89 208 89 208 105 208 105 245 105 245 119 245 150
AS 260 S Y/PT
4800 1712 105 74 150 74 150 74 150 74 173 89 208 89 208 105 208 105
21 0 t rear
21.0
4800 2072 173 89 208 89 208 105 208 105 245 105 245 105 245 150 286 150
289/199x80x6 7
289/199x80x6,7
5100 1802 150 74 150 74 173 89 208 89 208 105 208 105 245 105 245 105
5700 2432 245 105 245 105 286 150 286 150 286 150 317 173 343 208 343 208
6050 2657 286 150 286 150 317 173 343 208 343 208 374 208 374 245 406 245
3120 722 46 - 46 - 46 - 46 - 46 - 46 - 46 - 46 46
3805 1757 105 46 105 57 119 57 119 74 150 89 173 89 173 105 173 105
4200 1127 46 46 57 46 57 46 57 46 74 46 89 46 89 46 89 46
4200 1622 105 46 105 57 119 57 119 74 150 89 173 89 173 89 173 105
4200 2117 150 89 173 89 173 105 173 105 208 119 245 135 245 150 245 173
AS/AD/AT 260 S
4500 1217 57 46 74 46 74 46 89 46 89 46 105 46 105 57 105 57
Y/P Y/FP
Y/P.., 4500 1622 105 57 105 57 119 74 135 89 173 89 173 89 173 105 173 105
19.0 t rear 4500 1802 119 57 135 89 173 89 173 89 173 105 173 105 173 105 208 119
IInvalid
lid for
f versions
i /
4500 2072 173 89 173 105 173 105 173 105 208 119 245 135 245 150 245 173
TN /PT CT and GV
TN,/PT
4800 1487 105 46 105 57 105 57 119 74 135 74 150 89 173 89 173 105
289/199x80x6,7
4800 1712 119 57 135 74 150 89 173 89 173 105 173 105 173 105 208 119
4800 2072 173 105 173 105 173 105 208 119 245 135 245 150 245 173 245 173
5100 1802 150 89 173 89 173 105 173 105 173 105 173 119 245 119 245 135
5700 2432 105 46 105 74 150 74 150 74 173 74 208 89 208 105 208 105
6050 2657 150 74 150 74 173 89 208 105 208 105 245 105 245 105 286 150

R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
body
overhang
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
3120 722 46 - 46 - 46 - 46 46 46 46 46 46 46 46 46 46
3805 1757 135 74 173 89 173 89 173 105 173 105 173 105 208 119 245 135
4200 1127 74 46 89 46 89 46 89 46 105 46 105 46 105 57 105 57
4200 1622 135 74 150 89 173 89 173 105 173 105 173 105 173 105 208 119
4200 2117 173 105 208 119 245 135 245 150 245 173 245 173 245 173 245 173
4500 1217 89 46 89 46 105 46 105 57 105 57 119 57 135 74 135 89
AS/AD/AT 260 S
4500 1622 150 89 173 89 173 105 173 105 173 105 173 105 208 119 245 135
Y/P Y/FP
Y/P..,
4500 1802 173 105 173 105 173 105 208 119 245 119 245 135 245 173 245 173
20 t rear 4500 2072 173 105 245 135 245 150 245 173 245 173 245 173 245 173 245 173
289/199 80 6 7
289/199x80x6,7
4800 1487 119 74 135 89 173 89 173 89 173 105 173 105 173 105 173 105
4800 1712 173 89 173 105 173 105 173 105 208 119 245 135 245 150 245 173
4800 2072 208 119 245 135 245 173 245 173 245 173 245 173 245 173 343 173
5100 1802 173 105 173 105 208 119 245 135 245 150 245 173 245 173 245 173
5700 2432 150 74 208 89 208 105 208 105 245 105 245 135 286 150 286 150
6050 2657 208 105 245 105 245 105 245 150 286 150 286 150 317 173 343 208
3120 722 46 46 46 46 46 46 46 46 46 46 46 46 46 46 46 46
3805 1757 173 105 173 105 173 119 245 119 245 135 245 150 245 173 245 173
4200 1127 89 46 105 46 105 57 105 57 119 57 119 74 135 74 150 89
4200 1622 173 105 173 105 173 105 208 119 245 119 245 135 245 150 245 173
4200 2117 245 173 245 173 245 173 245 173 245 173 343 208 343 245 374 245
AS/AD/AT 260 S
4500 1217 105 57 105 57 119 74 135 74 150 89 173 89 173 89 173 105
Y/P.., Y/FP
Y/P 4500 1622 173 105 173 105 173 119 208 119 245 135 245 150 245 173 245 173
I lid for
Invalid f versions
i / 4500 1802 208 119 245 135 245 150 245 173 245 173 245 173 245 173 245 173
TN /PT CT and GV
TN,/PT
4500 2072 245 173 245 173 245 173 245 173 245 173 343 208 343 245 374 245
21 t rear
4800 1487 173 89 173 105 173 105 173 105 173 119 208 119 245 135 245 150
289/199x80x6,7
4800 1712 173 105 245 119 245 135 245 150 245 173 245 173 245 173 245 173
4800 2072 245 173 245 173 245 173 245 173 343 208 343 245 374 245 374 245
5100 1802 245 135 245 150 245 173 245 173 245 173 245 173 245 173 317 173
5700 2432 245 105 245 105 286 150 286 150 286 150 317 173 343 208 343 208
6050 2657 286 150 286 150 317 173 343 208 343 208 374 208 374 245 406 245
4200 2117 105 - 105 - 105 - 150 - 150 74 173 74 208 89 208 105
4500 2072 105 - 105 - 135 - 150 74 150 74 173 89 208 105 208 105
4800 2072 105 - 105 - 150 - 150 74 173 89 208 105 208 105 208 105
AS/AD/AT 260 S
5100 1802 89 - 105 - 105 - 135 - 150 - 150 74 173 74 208 89
Y/FP-GV
Y/FP GV
5700 2432 173 89 208 105 208 105 245 105 245 150 286 150 286 173 317 173
only with CCM 11954
- - - - - - - - - - - - - - - - - -
19 t rear
- - - - - - - - - - - - - - - - - -
289/199x80x7 7
289/199x80x7,7
- - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - -

R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
body
overhang
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
4200 2117 74 - 74 - 89 - 105 - 105 - 105 - 105 - 105 -
4500 2072 74 - 89 - 105 - 105 - 105 - 105 - 105 - 150 -
AS/AD/AT 260 S 4800 2072 74 - 105 - 105 - 105 - 105 - 135 - 150 - 150 74
Y/FP GV
Y/FP-GV 5100 1802 74 - 74 - 89 - 105 - 105 - 105 - 105 - 150 -
only with CCM 11954 5700 2432 150 - 150 74 150 74 173 74 173 89 208 89 208 105 208 105
1200 towbar - - - - - - - - - - - - - - - - - -
19 t rear - - - - - - - - - - - - - - - - - -
289/199x80x7,7 - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - -
3800 1765 46 46 46 46 57 46 74 46 74 46 74 46 89 46 105 46
4200 1630 46 46 46 46 57 46 74 46 74 46 74 46 74 46 89 46
4200 2125 74 46 89 46 105 46 105 57 105 74 150 74 150 74 150 74
4500 1630 46 46 46 46 57 46 74 46 74 46 74 46 89 46 105 46
4500 1810 57 46 74 46 74 46 74 46 89 46 105 46 105 57 105 74
AD/AT 260 S ../TN
/TN
4500 2080 74 46 89 46 105 46 150 57 105 74 150 74 150 74 173 89
19 0 t rear
19.0
4800 1495 46 46 46 46 46 46 57 46 74 46 74 46 74 46 74 46
289x80x6 7
289x80x6,7
4800 1720 57 46 74 46 74 46 74 46 89 46 105 46 105 46 105 57
4800 2080 74 46 105 46 105 57 105 74 150 74 150 74 150 74 173 89
5100 1810 74 46 74 46 74 46 89 46 105 46 105 57 105 74 150 74
5700 3025 245 105 245 150 286 150 286 173 317 208 343 208 374 208 406 245
6050 2665 208 89 208 105 245 105 245 150 286 150 286 150 317 173 343 208
3800 1765 74 46 74 46 74 46 89 46 105 46 105 57 105 74 135 74
4200 1630 74 46 74 46 74 46 89 46 89 46 105 46 105 57 105 74
4200 2125 105 57 105 74 150 74 150 74 173 89 208 89 208 105 208 105
4500 1630 74 46 74 46 74 46 89 46 105 46 105 46 105 57 105 74
4500 1810 74 46 105 46 105 46 105 57 105 74 150 74 150 74 150 74
AD/AT 260 S ../TN
4500 2080 105 57 135 74 150 74 150 74 173 89 208 105 208 105 245 105
50:50 o 60:40
4800 1495 57 46 74 46 74 46 74 46 74 46 89 46 105 46 105 46
21 0 t rear
21.0 4800 1720 74 46 89 46 105 46 105 57 105 74 105 74 150 74 150 74
289 80 6 7
289x80x6,7
4800 2080 105 74 150 74 150 74 173 89 208 89 208 105 208 105 245 105
5100 1810 89 46 105 46 105 57 105 74 150 74 150 74 150 74 173 89
5700 3025 286 150 343 208 343 208 374 245 406 245 406 245 406 286 474 286
6050 2665 245 135 286 150 286 173 317 208 343 208 374 208 374 245 406 245
6050 2665 317 208 343 208 374 208 374 245 406 245 406 245 406 286 474 286

R≤ 9500 R≤ 12000 R≤ 14000 R≤ 16000 R≤ 18000 R≤ 20000 R≤ 22000 R≤ 24000
body
overhang
(mm)
S235 = ST 37 = FE 360 = 240 S355 = ST 52 = FE 510 = 360
240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
3800 1765 89 46 105 46 105 57 105 74 150 74 150 74 150 74 173 89
4200 1630 89 46 105 46 105 46 105 57 105 74 150 74 150 74 150 74
4200 2125 150 74 173 89 205 105 208 105 245 105 245 105 245 150 286 150
4500 1630 89 46 105 46 105 57 105 74 105 74 150 74 150 74 150 74
4500 1810 105 57 105 74 150 74 150 74 173 74 208 89 208 105 208 105
AD/AT 260 S ../TN
/TN
4500 2080 150 74 208 89 208 105 208 105 245 105 245 105 245 150 286 150
21 0 t rear
21.0
4800 1495 74 46 74 46 89 46 105 46 105 46 105 57 105 74 135 74
289x80x6 7
289x80x6,7
4800 1720 105 57 105 74 105 74 150 74 150 74 150 74 173 89 208 105
4800 2080 173 89 208 105 208 105 245 105 245 105 245 135 286 150 286 150
5100 1810 105 74 150 74 150 74 173 74 173 89 208 105 208 105 208 105
5700 3025 374 245 406 245 406 286 474 286 474 286 SP 317 SP 343 SP 343
6050 2665 317 208 343 208 374 208 374 245 406 245 406 245 406 286 474 286
2840 2072 46 - 46 - 46 - 46 - 46 46 46 46 46 46 46 46
3140 1802 46 - 46 - 46 - 46 - 46 46 46 46 46 46 46 46
AS 260 S .. X/P
3440 2477 46 46 46 46 57 46 74 46 74 46 74 46 89 46 105 46
19 0 t rear
19.0
3740 2387 46 46 57 46 74 46 74 46 74 46 89 46 105 46 105 57
289x80x6 7
289x80x6,7
4340 2207 74 46 74 46 74 46 89 46 105 46 105 46 105 57 105 74
4690 2657 105 46 105 46 105 74 150 74 150 74 173 74 208 89 208 105
2840 2072 46 46 46 46 46 46 46 46 57 46 74 46 74 46 74 46
3140 1802 46 46 46 46 46 46 46 46 57 46 74 46 74 46 74 46
AS 260 S .. X/P
3440 2477 74 46 74 46 105 46 105 46 105 57 105 74 150 74 150 74
20 0 t rear
20.0
3740 2387 74 46 105 46 105 46 105 74 105 74 150 74 150 74 173 89
289x80x6 7
289x80x6,7
4340 2207 89 46 105 46 105 57 105 74 150 74 150 74 150 74 173 89
4690 2657 150 74 173 74 208 89 208 105 208 105 245 105 245 105 286 150
2840 2072 57 46 74 46 74 46 74 46 89 46 105 46 105 57 105 74
3140 1802 57 46 74 46 74 46 74 46 89 46 105 46 105 46 105 57
AS 260 S .. X/P
3440 2477 105 57 105 74 150 74 150 74 173 89 208 105 208 105 208 105
21 0 t rear
21.0
3740 2387 105 74 150 74 150 74 173 89 208 89 208 105 208 105 245 105
289x80x6 7
289x80x6,7
4340 2207 150 74 150 74 173 74 208 89 208 105 208 105 245 105 245 105
4690 2657 208 105 245 105 245 105 286 150 286 150 286 150 317 173 343 208
AS 260 S .. Z/P-HM 3800 1487 46 - 46 - 46 - 46 46 46 46 46 46 46 46 46 46
19.0
9 0 t rear
ea 4200 1847 46 46 46 46 46 46 46 46 57 46 74 46 74 46 74 46
289x80x6,7 4500 1982 46 46 46 46 57 46 74 46 74 46 74 46 89 46 105 46
AS 260 S .. Z/P-HM 3800 1487 46 46 46 46 46 46 46 46 46 46 57 46 74 46 74 46
20.0
0 0 t rear
ea 4200 1847 57 46 74 46 74 46 74 46 89 46 89 46 105 46 105 57
289x80x6,7 4500 1982 74 46 74 46 89 46 105 46 105 46 105 57 105 74 150 74
AS 260 S .. Z/P-HM 3800 1487 46 46 57 46 74 46 74 46 74 46 74 46 89 46 105 46
21.0
0 t rear
ea 4200 1847 89 46 105 46 105 46 105 57 105 74 150 74 150 74 150 74
289x80x6,7 4500 1982 105 57 105 74 135 74 150 74 150 74 173 74 208 89 208 105
NOTE See Table 3.2 (section bar dimensions)

Table 2.14 - Combined section reinforcement runner profiles Table 3.4

A B C or D E F G
Material yield point (N/mm2) ≤ 320 ≤ 320 ≤ 240 ≤ 240 ≤ 360 ≤ 360
Max. runner profile height 40 60 100 120 100 120
reduction (mm):
Combined reinforcements length
LV : 00.5.L
5 LU 0.5.L
0 5 LU 0 8LU
0.8L 0.85L
0 85LU 0 8 LU
0.8.L 00.85.L
85 LU
LH : 0.6.LU 0.6.LU 0.95LU 1.0.LU 0.95.LU 1.0.LU
Example: Combined section as an 210X80X8 190X80X8 150x80x8 130x80x8 150x80x8 130x80x8
alternative to the channel section + straight + straight + angle + angle
C250x80x8 (mm) section section section section
15x80 15x80
Actual height reduction (mm): 40 52 85 97 92 104
The continuity of combined reinforcement runners can be interrupted only in special cases and is subject to authorisation. Similarly, when it is difficult to apply
an external reinforcing L section (items F and G Figure 3.4) - owing to the presence of suspension mountings or air spring connection brackets - and the recessing
to be performed could excessively reduce the section’s resisting capacity, the adopted solution will require special authorisation.
2.6.4.1 Centre axle trailers: towing cross member in lowered and forward positions
(short coupling)
Vehicles designed to tow centre axle trailers for which a final cross member located in a lowered or forward position (next
to the rear suspension rear mountings or air springs) is evisaged, do not require particular chassis reinforcing devices. For the sub-
frame, the runner profile dimensions indicated for the different types of equipmen t (e.g. see Table 3.4 standard bodies) will be suffi-
cient. The bodybuilder will accurately work out the size and position of the chassis connection structure (see point 2.6.3 and 2.6.4)
and make use of a suitable cross member and an appropriate towing hook.
The tow hook position will be such to permit any movement between vehicle and trailer drawbar according to the various conditions
of use, to comply with the required safety margins and the standards and legal regulations in force (where applicable). In these cases
the standard underrun bar cannot be used, and the bodybuilder will investigate the possible permitted changes from specifications
or the specific solutions to adopt (e.g. tilt type underrun bar).
2.6.4.2 Reinforcement of Standard Rear Cross Member
When it is necessary to reinforce the standard cross member and when original cross members are not available, the bodybuilder
will provide suitable reinforcements for which he shall be responsible.
These reinforcements may consist of C-sections mounted on the inside of the cross member. Care must be taken to ensure that
the connections between the cross member and the side members are also reinforced following the procedures recommended
below, whenever stronger enforcements are required:
1) The mounting of a channel section on the inside of the cross member and joining it to the vertical web of the side member
or to the following cross member of the chassis, if it is situated in close proximity, in compliance with the procedures illustrated
in Figure 2.13.

Figure 2.13
91459
1. Original cross member - 2. Reinforcing rail - 3. Connecting angle pieces or plates
2) Mounting a box section of suitable dimensions underneath the cross member, anchored at the extremities to the vertical web
of the side members and joined at the centre of the cross member as shown in Figure 2.14.
In vehicles having a short rear overhang and a subframe, the box section can be fitted within the subframe sections, above the
cross-member, and connected to it by means of a plate (as shown in Figure 2.12).
Should box-section assembly require modification to underrun bar plates the original requirements for fastening, resistance and stif-
fness must be met (comply with local government regulations if any).

Figure 2.14
91460
1. Original rear cross member - 2. Box section - 3. Connecting plate - 4. Ribbing plate
2.6.4.3 Tow hooks for Centre Axle Trailers
The use of centre axle trailers involues the use of tow hooks suitable for this purpose.
The values of the trailer loads and of the permissible vertical loads are contained in the technical documentation of the manufacturer
of the tow hook or on the production data plate (e.g. DIN 74051 and DIN 74052).
There are also tow hooks with special type approval, whose values are greater than the ones mentioned in the above standards.
These hooks may in any case be subjected to restrictions depending on the trailers used (e.g. drawbar length). In addition this can
imply that the rear cross member should be further reinforced and a subframe runner of larger size be fitted.
2.6.4.4 Remarks about the Payload
It should be ascertained that the static drawbar load does not cause the allowable load on the rear axle or axles to be exceeded
and that the required minimum load acting on the front axle is adhered to see point 1.13.3.
2.6.4.5 Increasing the Towable weight
For those vehicles which IVECO regards as suitable for towing a trailer, a request may be submitted to evaluate the possibility
of authorising a towable weight exceeding that which is normally permitted.
Such authorisation will include the conditions that must be complied with and, where necessary, specifications concerning modifica-
tions and work to be carried out on the vehicle.
These include possible reinforcements to the standard cross member (see Figure 2.13), the instructions for installing a reinforced cross
member when available, and those on the brake system to be made.
The tow hook must be suitable for the new use. Its connecting flange must match that of the cross member.
To fasten the cross member to the chassis frame, preferably use flanged head nuts and bolts or hex head screws of minimum class
8.8. Use self-locking nuts.

Installing a Supplementary Axle
2.7 Installing a Supplementary Axle
The installation of an additional axle has heavy repercussions on the vehicle systems; in particular, it
! has a critical impact on the braking system, the compressed air system, the wiring harness and the
MUX interconnection systems.
Accordingly, the addition of an extra axle must be approved by IVECO and must be performed accord-
ing to the instructions given in chapter 5 “Special instructions for electronic subsystems”.
On certain models IVECO may authorise, upon request, the installation of a supplementary axle and, consequently, an increase
in the total weight of the vehicle.
The modification must respect the weight limitations and the conditions imposed by IVECO as well as all other conditions that may
be imposed by national laws and such that are necessary to ensure the safety and proper functioning of the vehicle.
Diagrams of the installation procedure may be submitted for inspection. These proposals must indicate the parts necessary to con-
nect the axle to the chassis as well as the reinforcements to, and modifications of the chassis. It is also necessary to submit diagrams
showing the changes made to the systems.
The specifications given in points 2.5 and 2.6 are to be followed for all modifications of the chassis.
In view of the increased stresses due to the increase in permissible load, and in consideration of the different phases of the dynamic
stresses in operation as a result of the different reactions on the chassis when the axle is added, it is necessary to provide appropriate
reinforcements to the chassis.
These reinforcements must in all cases satisfy all provisions of local applicable laws. The chassis that has thus been modified must
not be subject to flexural stresses greater than those of the original chassis in the corresponding sections.
2.7.2 Chassis Frame Reinforcement
Figure 2.15 illustrates possible ways of modifying the chassis. The reinforcements must be continuous and must span the length
of the entire frame of the vehicle up to the driver’s cab. For their attachment to the side member - when using L-bars - class 8.8
reinforcement bolts must be used and their diameter and distribution must be such to enable the section reinforcements to provide
the required strength.

Figure 2.15
91461
1. Bracket - 2. Plate - 3. Screws, rivets or Ø 20 to 30 mm holes to be filled with welding
Where an auxiliary frame is required as reinforcement (see point 3.1), the body mounting brackets on the chassis (if any) should
be used for the attachment. An alternative method of attachment is shown in point 3.1.2 and those that follow it.
We recommend using shear resistant connection in the area of the rear overhang up to approximately the mid wheelbase (or to
a point no closer than 2 m from the front axle) (see Figure 2.15).
The fitting of reinforcing plates directly onto the flanges of the side members, using holes filled with welded material is not permitted.
This is to avoid affecting the strength of the original sections caused by poor welding.
This procedure is only permitted in special cases with specific IVECO authorization when there are proven difficulties in subsequent
body applications.
It is possible to do without reinforcements on the frame if the static stress values in the Table 2.10 are not exceeded.
Any limitations, imposed by national regulations must be complied with.
Because of the deterioration of the material’s properties during the welding process, if the installation is unavoidable it is then advis-
able to assume a reduction of 15% in the strength of the material when checking the load-effects acting on the various sections
of the chassis.
As a general rule the thickness of the reinforcing plate must not exceed that of the flange of the original chassis.
The mounting must be carried out by skilled personnel and the bodybuilder will be responsible for any damage to the frame resulting
from poor workmanship.

2.7.3 Installing a Rear Supplementary Axle
The installation of a rear supplementary axle generally implies that the chassis overhang should be lengthened, the extension
must be carried out in compliance with the specifications given in point 2.5.3 relating to the modifications of the chassis, leaving the
reinforcements mentioned above unaffected.
When an additional axle is added to the overhang with a section depth smaller than the depth within the wheelbase area the adjust-
ment of the section to give a higher value could be a solution towards reducing the stress arising from the conversion.
In Figure 2.16 shows an example of the installation of a rear axle with an extension of the rear overhang.
Figure 2.16
123842
1. Added supplementary axle - 2. Extension to the overhang - 3. Reinforcements for the modification of the chassis -
4. Connections - 5. Reinforcing runner
Installing an Intermediate Supplementary Axle
The installation of an additional axle in a forward (intermediate) position relative to the drive axle may require a possible reduction
in the rear overhang (see point 2.5.2) in order to obtain the proper distribution of the weights (see Figure 2.18).
Figure 2.17
123841
1. Added supplementary axle - 2. Reinforcing runner - 3. Connections - 4. Reduction in the rear overhang

2.7.4 Steering Axles
Steering axles can be installed both intermediately and at the rear. They can be of the self-steering or force-steering types and
be designed and installed in such a way that the required dependability and road safety are guaranteed. The self-steering axle must
be fitted with a device controlled from the driver’s seat which will lock the axle in the straight position when reversing.
The installation of an axle whose force-steering is obtained by means of the original steering system of the vehicle requires specific
authorisation from IVECO in relation to the suitability of the original components for the conversion in question. In this case, it will
be necessary for diagrams of the supplementary system to be submitted for our inspection.
2.7.5 Components and Suspension
Manufacturing quality of all components used (axle, suspension, braking units, systems etc) must be ensured in order to guarantee
driving safety and good vehicle operation.
Particular care and attention must be paid to the designing and construction of the suspension in consideration of its importance
for the proper performance and handling of the vehicle on the road.
The designed suspension may be either of the mechanical leaf-spring type, pneumatic with air actuated springs or of a mixed type.
Whatever type is used it must not negatively affect the handling characteristics of the vehicle and its components in terms of driving
quality, comfort, road holding, working angle of die transmission and its working space in the case of an intermediate supplementary
axle.
Where the additional axle has its own independent suspension, the suspension characteristics must be proportional to those of
the original rear suspension in relation to the static loads applied to the two axles.
2.7.6 Stabilisers
When pneumatic suspension is used for the added axle, depending on the solution adopted, it may be further necessary to fit
an antiroll bar in particular when a body with a high centre of gravity is used.
Similar measures must be adopted to ensure stability in relation to mixed type suspension on an additional rear axle.
2.7.7 Connection to the Chassis Frame
The connections of the added axle to the chassis must be such as to be able to withstand all longitudinal and transverse stress
forces without transmitting them to the drive axle.
At the points in which the forces are introduced (spring supports, air spring brackets etc.), appropriate cross members or suitable
frame reinforcements must be provided.
Ensure that the added axle is at right angles and aligned properly in relation to the longitudinal axis of the vehicle and the live axle.
Check using the appropriate equipment available in the market.

2.7.8 Braking system for additional axle
The braking system, considering its importance relative to the active safety of the vehicle, must be
! extremely well developed and constructed.
Braking units, hoses and joints of the same type as on the original vehicle must be used.
The auxiliary axle must be equipped with the same brake components as those provided for the front axle.
Use flexible pipes to form the connection between the fixed parts (chassis) and moving parts (axles).
The braking torque must be proportional to the static and dynamic loads in order to provide an even distribution of the braking
action to all the axles of the vehicle.
The total braking capacity of the modified vehicle must, as a general rule, be proportional to that of the original vehicle, allowing
for the different total mass that is now applicable. The performance of the braking system (service, emergency and parking) must
in all cases satisfy the current government regulations in terms of deceleration, behaviour when hot, response time, efficiency of
engine braking and so forth.
If the Technical Control Authority demands that the technical documentation regarding the braking system be submitted (e.g. ad-
hesion curves, compatibility range diagram) this must be provided by the company in charge of the conversion or the manufacturer
of the auxiliary axle.
Upon request, technical documentation with characteristics and attainable performances of the braking system of the original vehicle
may be made available.
For the construction of the braking circuit for the additional axle it is advisable to employ equipment and circuits specially provided
for each single model by the Manufacturer of the equipment in use on the original vehicles.
Solutions are allowed that include direct connection between the additional axle braking section and the engine axle braking section.
Check that the air tank capacity is sufficient for the size of the new additional brake cylinders. If necessary, fit a supplementary air
tank.
Current legal requirements must be complied with for the emergency and parking brake. We recommend that a parking brake is
fitted on the additional axle.
For indications of a general nature concerning the braking system, see the instructions given at point
! 2.15.
For the electrical system, comply with the indications provided at point 5.5.
2.7.9 Raise Device
The additional axle may be equipped with a raise device and may also be used in specific cases where permitted by government
regulations, to increase the adhesion of the drive axle to the ground under certain conditions (starting uphill, slippery or snow/ice
covered roads) provided that:
- This modification is made conditional to the issue by IVECO of a permit in which the maximum permitted load on the overloaded
axle is specified.
- The device is used only for driving short distances for the uses stated above, and at the maximum speed stated on the specific
authorization.
Some national regulations permit the use of the lifting device even during normal vehicle travel, provided that the max. type-approval
load specified for the drive axle and admissible speed limits are not exceeded.
In such cases the indications given in point 1.13.2 should be heeded concerning the centre of gravity of the body plus the payload.
Approval of and Responsibility for the Operations Carried Out
Following conversion, the vehicle must be submitted to local authority technical control for approval (e.g.
single inspection or type approval).
The authorisation given by IVECO to install an auxiliary axle and the passing of the approval inspection do not free the bodybuilder/
converter from responsibility for the conversion in question, or its effect on the vehicle.
For the added assemblies, the required service or maintenance operations with relevant schedule, consistent with the operations
and relevant schedule planned for the original vehicle must be defined and entered in the specific documentation.

2.7.10 Modifying the suspension
Changes to the suspension can be made only with IVECO’s prior approval, the suspension being a sys-
! tem of decisive importance to riding safety.
As a general rule no modification of the parabolic springs is permitted. On vehicles equipped with these springs, installation of
elastic rubber components may be authorised for special versions or uses in order to increase the stiffness of the suspension. In
very specific cases, and for specific uses, the possibility may be evaluated of adding an extra leaf to the parabolic spring. This operation
should be carried out by a specialised firm following approval by IVECO.
The use on the same axle of one parabolic spring and one trapezoidal spring is not allowed.

Modifying the Drive Line
2.8 Modifying the Drive Line
Following the modification of the wheelbase, work on the transmission as a general rule, is carried out on the basis of the trans-
mission of a similar vehicle with approximately the same wheelbase. The maximum value of the inclinations of the propeller shafts
used for standard production vehicles is to be retained. This rule must also be applied when any modifications to the suspension
and rear drive axles are made.
In cases of particular difficulty, the assistance of the company may be sought. A diagram giving the length and inclination of the pro-
posed new transmission must accompany the request.
The purpose of the specifications contained in this manual is to ensure the proper functioning of the transmission, to limit its noise
and to avoid the build-up of stress transmitted from the engine assembly. In no way does this diminish the responsibility of the body-
builder for the work he has completed.
2.8.1 Permitted lengths
The maximum operating lengths obtainable for both the intermediate shaft sections and the sliding shafts ”LG” or ”LZ” (see
Figure 2.18) can be determined according to the external diameter of the tube existing on the vehicle and the maximum operating
rotational speed (see formula). These are specified in Table 2.15.
For the propeller shaft length specified in Table 2.15 when the tube diameter is not sufficient, a new shaft section with the same
characteristics as the existing shafts must be used. As an alternative, in some cases the transmission shaft with a larger diameter tube
can be used. The tube diameter required can be determined in compliance with the required length and the maximum rotational
speed, directly from Table 2.16.
Figure 2.18
INTERMEDIATE SHAFT SLIDING SHAFT
C C
LZ LG
SINGLE-SECTION SHAFT
116721

As far as sliding shafts are concerned, length LG is measured between the universal joint centres, with the sliding stub in its intermedi-
ate position.
As regards single-stub shafts, check both branches LG and LZ.
The maximum working revs can be obtained using the formula below:
n max
nG =
iG
nmax = maximum number of engine revolutions (rpm).

iG = gear ratio in fastest gear.
iV = transfer box ratio, equal to 1 if not present or for shafts upstream of the transfer box.
The maximum propeller shaft speed is determined on the basis of the following formula (the necessary data may be obtained from
the vehicle specifications and from the data plates on the engine, gearbox or transfer case).
n max
nG =
iG
ng = Max. prop. shaft speed (rpm).

nmax = Max. engine speed (r.p.m.).
iG = Gearbox ratio at top speed.
The greater thickness of the tube depends on the class, i.e. on the torque that the original shaft has to transmit and on the design
of the driveline (torque, ratios of kinematic chain, power axle load).
A reference value for the thickness of the tube of a general validity cannot be given. When, for example, a tube of a larger diameter
is to be used, its thickness should theoretically be reduced until the torsional strength of the original tube is achieved. It should
however be noted that, to determine the thickness of the tube, the following points are to be taken into account: the size of the
male element of the fork, the possible necessity of adapters and the sizes of the tubes available.
Therefore the thickness of the tube should be agreed upon as each occasion arises with the workshops authorised by the manufac-
turers of the transmission shaft depending on its dimensions (i.e. size of the universal joint).
The minimum operating length (from flange to flange) must not be less than 800 mm for the sliding sections and 700 mm for the
intermediate sections.
Table 2.15 - Obtainable propeller shaft characteristics
Max achievable lengths LG or LZ (mm)

Outer diameter x 1800 1900 2000 2100 2200 2300 2400 2500
Joint size
thi k
thickness (
(mm)
)
Maximum number of propeller
shaft revolutions (rpm)
2040 100 x 4.5 3400 3150 2900 2650 2450 2300 2100 1950
2040 120 x 3 4450 4100 3750 3400 3150 2900 2650 2450
2045 120 x 4 4450 4050 3700 3400 3100 2850 2650 2450
2055 120 x 6 4400 4000 3650 3350 3100 2850 2600 2400
2060 130 x 6 4650 4250 3900 3600 3300 3050 2800 2600
2065 142 x 6 5000 4600 4200 3900 3600 3300 3050 2850

The maximum possible lengths given above refer to the original shafts; plan for shorter lengths (-10%)
! for shafts obtained for by modification.
2.8.2 Determining Driveshaft Positions
In the case of drive lines which consist of several shafts, the individual shafts must all be approximately of the same length. As
a general rule, the difference in length between a non sliding and a splined shaft (see Figure 2.19) must not exceed 600 mm. The
difference in length between the shafts must not be more than 400 mm. A margin of at least 25 mm must be left so that the sliding
joint can travel when the splined shaft is closed. When fully extended the shaft sliding sleeve should cover the splined stub for a
length that should be about twice the diameter of the splined stub itself.
When the required length of the drive line exceeds the permissible length, an additional driven shaft must be provided as illustrated
in Figure 2.19.
Figure 2.19
91451
1. Engine, clutch, gearbox axis - 2. Intermediate shaft (non sliding) - 3. Intermediate shaft support - 4. Propeller shaft with sliding
end - 5. Inclination of rear axle case (static load) - 6. Inclination of rear axle case (max. compression) - 7. Inclination of rear axle
case (unladen) - 8. Intermediate shaft and axle case axis must have the same inclination

The intermediate shaft and the inclination of the rear axle case must be aligned accurately.
The difference in their inclination relative to the engine-clutch-gearbox axis must not vary more than 1°. This can be achieved by
fitting wedges between the rear axle and the springs, or by adjusting the rear axle reaction bars. The inclination of the rear axle must
not exceed 5.5°
When, with a loaded vehicle, the rear axle flange is at a level which is lower than that of the gearbox flange, care must be taken
to ensure that the inclination of the differential housing and of the driven shaft are greater than the inclination of the engine-gearbox
axis. On the other hand, if, with a loaded vehicle, the rear axle flange is at a level which is higher than that of the gearbox flange,
the inclination of the differential housing and of the driven shaft must be less than the inclination of the engine-gearbox axis.
When lengthening the wheelbase is substantial, it may become necessary to fit a supplementary intermediate shaft as shown in Figure
2.20. In this case the same inclination must be maintained between the engine-gearbox axis, the second intermediate shaft and the
axis of the differential housing.
Figure 2.20
91452
1. Engine, clutch, gearbox axis - 2. 1st intermediate shaft - 3. Intermediate shaft support - 4. 2nd intermediate shaft -
5. Propeller shaft with splined end - 6. Inclination of rear axle case (static load) - 7. Inclination of rear axle case (max.
compression) - 8. Inclination of rear axle case (unladen) - 9. Gearbox, 2nd intermediate shaft and rear axle case axis must have
same inclination.
Elastic supports must be fitted with the aid of supporting plates, at least 5 mm thick (see Figure 2.21), connected to cross-members
having the same characteristics as those specified by IVECO.
When reducing the wheelbase it is recommended that the intermediate shafts are removed if the length of the splined shaft is less
than approximately 800 mm.
Figure 2.21
91453
1. Intermediate shaft - 2. Support bracket - 3. Backing plate - 4. Support of intermediate shaft
If the drive line consists of a single shaft the inclination of the axle housing must be the same as the inclination of the engine-gearbox
axis.

The same holds true also for vehicles with separate gearbox. In addition to this, as a general rule, the wheelbase of such vehicles
cannot be reduced beyond the measurement of the shorter wheelbase contemplated for standard production (tippers for example).
The use of original drive line parts from IVECO is recommended for these modifications however. Should this not be possible, har-
dened steel tubes with a yield point of not less than 420 N/mm2 (42 kg/mm2) may be used.
Modifications to the universal joints are not permitted.
Whenever the transmission or part thereof, is modified, each modified section must be subjected to careful dynamic balancing.
Since transmission is important to vehicle driving safety, it should be borne in mind that any
! modification to it must bear maximum operational guarantees. Only very specialised and transmission
manufacturer-certified companies should therefore be employed to carry out work of this kind.
IVECO’s approval is not required, if the frame is extended at the rear, or is shortened to the minimum value admissible for each
model as standard, provided that this is done according to the instructions given herein.
If it proves necessary modify the length of the electrical circuits, see chapter 5 “Special instructions
! for electronic subsystems”.

Modifications of the Engine Air Intake and Exhaust Syatem
2.9 Modifications of the Engine Air Intake and Exhaust System
2.9.1 Intake
The specifications of the engine air intake and exhaust systems must not be altered without prior authorisation from IVECO.
Modifications carried out must not alter the vacuum levels (for the intake) or the original exhaust back pressure levels.
Table 2.16 - Engine Back Pressures
Engines Engine Code Maximum exhaust back Maximum intake back

pressure (kPa) pressure (kPa)
CURSOR 8
E31 F2BE3681C
E33 F2BE3681B 20 6.5
E36 F2BE3681A
CURSOR 10
E42 F3A3681B
E45 F3A3681A 19 6.5
E46 F3A3681Y
CURSOR 13
E41 F3B3681D
E44 F3B3681G
E45 F3B3681C
E48 F3B3681F 28 6.5
E50 F3B3681B
E52 F3B3681E
E56 F3B3681A
The air intake must be positioned to avoid the intake of hot air from the engine and/or dusty air snow or rain. The apertures for
the intake of air which may have to be made in the side of integral bodies, must have a working surface of not less than two and
a half times that of the master hose located upstream of the filter. These apertures (e.g openings in the grill) must be of such a dimen-
sion that they do not become obstructed. It is prohibited to alter the air filer or replace the original filter with a lower air capacity
unit. Any connections on the intake duct must guarantee resistance of the tube to penetration by water or dust and free from sharp/
rough edges (or welding burrs inside metal tube). It is not permissible to modify or substitute the original air filter.
2.9.2 Engine exhaust

The routing of the exhaust pipe must be as even as possible. Bends must not have an angle of less than 90º and the radii should
not be less than 2.5 times the external diameter. Avoid kinks and use cross-sections which are no smaller than those corresponding
to the original system. Any connections on the intake duct must guarantee resistance of the tube to penetration by water or dust
and absence of sharp edges or welding burrs inside the tube. Sufficient clearance should be maintained (min. 150 mm) between
the exhaust pipe and the electrical system, plastic hoses, the spare wheel, the plastic fuel tank (min. 100 mm), etc. Lower values
(e.g. 80 mm) may be permitted if suitable sheet metal shielding is used. Further reductions require the use of heat insulation and
the substitution of the plastic tubes with steel pipes. It is not permissible to modify or substitute the original air filter; the silencer
body cannot be altered. Modifications to the silencer body and engine equipment (injectors, engine control unit etc.) are not permiss-
ible as this may alter the correct functioning of the engine and adversely affect the emissions of gases from the exhaust.
NOTE Chapter 6 concerning SCR contains additional information on exhaust system changes.
Modifications of the Engine Air Intake and Exhaust Syatem

Modification of the Engine Cooling System
2.10 Modification of the Engine Cooling System
The proper functioning of the original system, especially in connection with the radiator, the free surface of the radiator and hoses
(dimensions and layout) must not be tampered with. Whenever modifications must be made that entail work on the engine cooling
system (e.g., modifications to the cab), the following points must be considered:
- The useful area for the passage of air for the cooling of the radiator must not be less than that which is available on vehicles
with the standard cab. Maximum venting of air from the engine compartment must be ensured and care must be taken - possibly
using shields or baffles - to avoid stagnant air pockets or back flow of air. The performance of the fan must not be altered.
- If it is necessary to re-position the hoses this must be done without affecting the complete filling of the system (which must occur
at a continuous flow without forming blockages at the mouth) or the normal flow of water. The maximum stabilising temperature
of the water must not be altered even under the most severe operating conditions.
- Hoses must be located so that air pockets are not formed (i.e avoiding air traps and providing appropriate bleeding points) that
could hinder the circulation of water. Check that the water pump primes immediately on starting the engine and later operates
with the engine idling (accelerate a few times, if necessary) even when the circuit is not pressurized. Check that the delivery
pressure of the water pump, when the engine is running under no load and at maximum RPM, is not lower than 1 bar.
- Always reinstall the radiator anti-clogging protection after making alterations to the engine cooling system.
Modification of the Engine Cooling System

Installation of a Supplementary Heating System
2.11 Installation of a Supplementary Heating System
When the installation of a supplementary heating system is deemed necessary, it is advisable to use the types recommended
by IVECO.
For vehicles on which IVECO has not planned the use of supplementary heaters, the installation should be carried out in compliance
with the supplier’s instructions (i.e. heater arrangement, piping, electrical system etc.) and following the directions given below.
All national rules and regulations relevant to the matter should be adhered to (i.e. inspections, particular installation for dangerous
cargo transportation etc.). The supplementary heating system must not make use of the equipment that is specific to the vehicle
which is subject to approval if the use is liable to impair or alter the performance of the equipment.
Furthermore:
- ensure correct operation of the vehicle components and equipment (i.e. cooling system);
- check the electrical system to ensure that the battery capacity and alternator output is sufficient for the higher current require-
ments (see point 5.5). Provide the new circuitry with a protection fuse;
- connect the intake of the newly added fuel system to the reservoir connected to the engine fuel return line. Direct feed from
the vehicle fuel tank is permitted only if this is independent from the engine fuel system and the new circuit is perfectly leakproof;
- trace pipe and cable paths, the location of brackets and hoses bearing in mind that the overall dimensions and heat affect the
various units on the chassis. Avoid runs and arrangements that could lead to hazards when the vehicle is running. Use shields
or armouring if necessary;
- When installing a water heater, original vehicle heating and engine cooling circuits are involved (see point 2.10), it is advisable
to follow the instructions listed below to ensure reliability of the heating system and safe operation of the original system:
- special care must be taken when defining the connections between the supplementary equipment and the main one; refer
to IVECO, if necessary;
- determine a rational arrangement for piping, avoid neckings and siphonings;
- install proper venting valve (bleeding points) to ensure proper filling of the system;
- supplementary plugs should be installed to ensure draining of the system, if necessary;
- proper insulation should be used to prevent heat dissipation.
- When air heaters are used and when the installation is to be made directly in the cab, make sure that the engine exhaust system
does not touch the added installation (to prevent exhaust gas circulation inside the vehicle) and have the correct warm air
distribution by avoiding direct air flows;
- the complete installation should be designed to ensure good accessibility for quick and easy servicing.
Installation of a Supplementary Heating System

Installing an Air---Conditioning System
2.12 Installing an Air-Conditioning System
When the installation of an air conditioning system is deemed necessary, it is advisable to use the types recommended by IVECO.
If this procedure is not applicable, the installation must be carried out in accordance with the supplier’s instructions and the following
points:
- the installation must not interfere with the correct operation of the vehicle components and of equipment which may be con-
nected with the installation;
- check the electrical system to ensure that the battery capacity and alternator output is sufficient for the higher current require-
ments (see point 5.5.3). Provide the new circuitry with a protection fuse;
- in liaison with IVECO, establish a method for installing the compressor; if it is fitted to the engine, use the original IVECO com-
pressor;
- trace pipe and cable paths, the location of brackets and hoses bearing in mind that the overall dimensions and heat affect the
various units on the chassis. Avoid runs and arrangements that could lead to hazards when the vehicle is running. Use shields
or armouring if necessary;
- the complete installation should be designed to ensure good accessibility for quick and easy servicing. At vehicle delivery, the
bodybuilder will supply all service and maintenance instructions which are deemed necessary.
Furthermore, according to the system operations:
a) Equipment installed inside the cab
- The condenser should not impair the original engine cooling system operation (reduction in the radiating area of the engine
radiator).
- The best arrangement is to use a condenser, suitably ventilated.
- The arrangement of the evaporator-blower unit in the cab (if not planned by IVECO) should be designed to make sure that
the accessibility control and operating equipment is not impaired.
b) Equipment fitted on the cab roof
- When the equipment (condenser, evaporator, blower) is fitted on the cab roof, make sure that its weight is not higher than that
permitted for roof installation. Furthermore, the bodybuilder must provide proper reinforcement to the roof frame if necessary,
in relation to the weight of the unit and the extent of the modification introduced.
- For specific applications with compressors not supplied by IVECO (e.g. fridge box), contact the IVECO offices in charge.
Installing an Air-Conditioning System

Cab Modifications
2.13 Cab Modifications
Any work on the driver’s cab must first be authorised by IVECO before any work is started.
Modifications must not prevent operation of the control devices located in the area affected by the modifications (e.g. pedals, linkages,
switches, pipes etc) or alter the strength of the loadbearing elements (uprights, reinforcement sections etc.). Due care must be
taken when carrying out work that may affect the cooling system and air inlet pipes of the engine.
When defining the position of payload, account must be taken of the variation in cab weight, in order to ensure the correct distribu-
tion of the permitted loads on the axles (see point 1.13).
For operations that require the removal of sound deadening panels or internal protective elements (panelling, padding) restrict the
removal to the absolute minimum, taking care to restore the protective elements to their original condition, ensuring the previous
operating capability.
Controls and equipment (power take-off engagement control, external operating cylinder control etc.) may be fitted in the cab pro-
vided that:
- They are positioned, properly and are easily accessible to the driver.
- Safety, control and warning devices are fitted which meet the requirements of use and safety of the vehicle and its equipment
as well as the requirements of national legislation.
Ensure that the pipes and wires are correctly positioned particularly when the cab is tilted. Use the necessary fixings taking care to
observe the appropriate distances from the engine, heat sources and moving parts.
Provide the necessary protection from corrosion for all modifications to the structure (see point 2.2).
Ensure that seals are fitted correctly and apply sealant to those areas which require it.
Ensure that a perfect seal is provided against the infiltration of water, dust and fumes.
The bodybuilder must check that after modification, the cab satisfies legal requirements regarding both the inside and outside of
the vehicle.
2.13.2 Roof Panel Modifications
Installation and modification work to achieve specific refurbishments must be carried out with great care to safeguard the strength
and integrety of the cab and ensure that its operation and protection are maintained.
When fitting assemblies or devices on the roof, make sure that their weight does not exceed that permitted for the cab. These limits
can be supplied on request, as a function of type of superstructure.
Cab Modifications
Changing the Size of the Tyres
2.14 Changing the Size of the Tyres
Replacing the tyres with others of different sizes or with a different loading capacity with respect to those considered at the time
of vehicle type-approval must be approved by IVECO and it is also necessary to check for the need to reprogram the EBL or EBS
system.
Changing the size of the tyres may involve replacing the wheels with others of a correspondingly greater loading capacity. In this
case check whether the spare wheel carrier needs to be changed.
Mounting tyres of different sizes or types of construction on the same axle is prohibited.
Changing the size of the tyres may affect the ground clearance of the front and rear underrun guards, therefore the compliance
with the national legal requirements must be verified. Its supporting brackets, where necessary, may be replaced with other appropri-
ate, type-approved brackets.
The use of larger tyres always necessitates verification of the safety margins for the mechanical parts, wheel arches etc., under all
dynamic conditions of steering and bump travel. In certain cases the use of wider tyres may entail a check on the axles to assess
the space required for the suspension components and the length of wheel studs etc.
Where there is local national legislation specifying overall widths (e.c. Jersey etc.) these must be complied with.
The use of tyres with a different outside diameter affects the performance of the vehicle in terms of speed, maximum gradability,
pulling force, braking power etc. The tachograph must be recalibrated by an authorised workshop. The load capacity and the relative
reference speed must always be compatible with the performance of the vehicle. When the tyres with a load capacity or speed
limit are chosen for a given vehicle, the permissible loads of the vehicle or its performance, must be reduced accordingly. On the
other hand, the use of tyres with a greater load capacity does not automatically increase the maximum permissible weight on the
axles.
The size and load capacity of the tyres are established on the basis of international and national norms (ETRTO, DIN, CUNA etc.)
and are listed in the manuals of the respective tyre manufacturers.
Specific performance characteristics may be established by government regulations for special use in the case of fire-fighting vehicles,
vehicles for winter duty, airport tankers, buses etc.. Whenever so required by government regulations the vehicle must be presented
to the respective government agency for inspection of the parts that have been replaced and entry of the respective modifications
in the vehicle documents.

Table 2.17 - Tyre configuration
Steel wheel Aluminium

Tyre size Rim
offset (mm) wheel offset (mm)
285/60R22,5 8.25 98 105
9.0 89 99
295/60R22,5 8.25 98 105
9.0 89 99
305/60R2,5 8.25 96 103
9.0 87 94
315/60R22,5 9.0 87 97
385/55R22,5 11.75 115 125
385/65R22,5 11.75 110 120
275/70R22,5 7.5 99
305/70R22,5 8.25 93 100
9.0 84 94
315/70R22,5 9.0 82 94
275/80R22,5 7.5 95
8.25 91 95
395/080R22.5 8.25 89 96
295/80R22.5 9.0 80 91
315/80R22,5 9.0 79 89
Tyre loading capacity is given in the individual manufacturers’ manuals.

Modifications to the Braking System
2.15 Modifications to the Braking System
The braking system with its components represents an element of crucial importance to vehicle safety.
! It is prohibited to make changes to units such as the brake force control system, distributor, brake cyl-
inders, valves, etc, which are rated as safety components.
Any changes to the braking system (changes to the piping, fitting additional operating cylinders, etc.)
require prior authorisation from IVECO.
For new equipment we recommend the same make as those fitted to the original vehicle.
When required by national regulations, the vehicle must be submitted for testing to the respective authority.
In the event of the regulating valves, air drier etc., being moved, reinstate the same type of installation as originally envisaged, verifying
correct operation. In addition, operations carried out on the air drier must not affect cooling of the air supplied by the compressor.
2.15.2 Brake Pipes
When the wheelbase or rear overhang of the chassis are modified, the brake pipes concerned must be replaced by a single length
of new pipe. Where this is not possible the connectors used must be of the same type as those used originally on the vehicle. When
replacing observe the minimum internal dimensions of the existing pipes.
The new pipes must have the same characteristics and be of the same material as those used originally on the vehicle. The installation
must be carried out so that the piping is protected and the correct function of the system ensured.
For the supply and fitting of material we recommend that you contact our Parts Centres or specialised workshops.
Plastic Pipes
When fitting new pipes or replacing others, plastic must not be used for the following:
- in areas where the temperature reaches more than 80°C (e.g. within 100 mm of the engine exhaust system).
- Between fixed and moving parts, in this case special hoses are to be used.
- On the hydraulic lines.
During modification the following must be observed:
- Material and dimensions Standard DIN 74324 (Iveco Standard 18-0400)
(max. operating pressure 11 bars)
- Radii of curvature : min. 6 Ø outer dia
(referred to the pipe centreline)

Preparation and installation (Iveco Standard 17-2403)
Cut the pipe at right angles (max. permissible variation 15°) using the correct tools to avoid flaws which could impair tightness.
Mark the portion of the length L (see Figure 2.22) to be inserted in the connector with indelible ink or adhesive tape to ensure
tightness. Mark the pipe to avoid confusion while it is being installed for subsequent modifications.
The Voss connector configurations are as shown in drawing 504225097.
Figure 2.22
End of stroke mark
d (mm) L(mm)
15° max Marking 6 19.8
8 20.5
10 24
12 25
16 27.1
91463
Table 2.18 - Configuration of the new connectors VOSS - SV214/W
pipe coupling VOSS IVECO GENERAL NOTES

Type
∅ ∅ reference reference Possible couplings with other connectors
Straight connector ∅ 6
IVECO No. 504148941 with thread M10x1
IVECO No. 504148950 with thread M12x1.5
6 6 5214010000 504149122
Intermediate connector ∅ 6 - 6
IVECO No. 504149318
8 8 5214010200 504149132
Intermediate connector ∅ 8 - 8
SV 214/W IVECO No. 504149327
6 5214010700 504149133 Straight connector ∅ 12

8 12 5214010900 504149136 IVECO No. 504149016 with thread M22x1.5
Intermediate connector ∅ 12 - 6/8/12

12 5214011100 504149139
IVECO No. 504149332

Table 2.19 - Configuration of the new connectors VOSS - SV214/GV SV214/GE
Receptacle GENERAL NOTES

pipe VOSS IVECO
Type SW key connector Possible couplings with other
∅ reference reference
thread connectors
90° connector ∅ 6
6 5214012000 504149318
IVECO No. 504149122 coupling ∅ 6
8 5214012100 504149327
12 5014012200 504149332
SV 214/GV 45° connector ∅ 12
L connector ∅ 12
T connector ∅ 12
(2x) 90° connector ∅ 8

22 m16 x 1.5 5214006400 504140020
8 IVECO No. 504149132 coupling ∅ 8
M18 x 1.5 IVECO No. 504149133 coupling ∅ 12
(with sealing
24 12 taper seat with 5214006200 504149022
pipe j 16) IVECO No. 504149136 coupling ∅ 12
on one side 90° connector ∅ 12
(2x) L connector ∅ 12
28 M22 x 1.5 5214006000 504149021
SV 214/GE 12 IVECO No. 504149170 coupling ∅ 12
M22 x 1.5
(inner thread T connector ∅ 12
28 12 5214006100 504149026
M16 x 1.5) IVECO No. 504149174 coupling ∅ 12
on one side

Table 2.20 - Configuration of the new connectors VOSS - SV214/W VOSS - 214/L VOSS - 214/T
pipe VOSS IVECO GENERAL NOTES

Type
∅ reference reference Possible couplings with other connectors
5214011600 504149148
SV 214/W
12 5214011200 504149170
Receptacle connector ∅ 12
SV 214/L IVECO No. 504149022 with thread M18x1.5
IVECO N
No. 504149026 with
i h thread
h d M22
M22x1.5
15
5214011300 504149174
SV 214/T
As a rule quick coupling connectors should be used. We recommend that the same makes present on the original vehicle be used.
When necessary (e.g. near bends), connectors with metal inserts may be used. Before inserting the pipe into the connector the latter
must be screwed into its threaded seat on the component (e.g. pneumatic valve) adopting the tightening torques indicated below.
Table 2.21
Thread Tightening torque (Nm + 10%)

M 12 X 1.5 MM 24
M 14 X 1.5 MM 28
M 16 X 1.5 MM 35
M 22 X 1.5 MM 40
Insert the portion of the length L, previously marked, of the pipe into the connector applying force for 30 to 120 N depending on the
dimension of the pipe.
The replacement of the components (valves etc.) is made possible since the coupling and connector may be internally rotated while
screwing or unscrewing.

Should piping be replaced:

! 1. If the connectors are of the Raufoss P5 type, use new connectors.
2. If the connectors are of the Voss 214 type, disassemble them using the special pliers, then re-fit them
on the new piping.
Installation of piping on vehicle
New pipes must be thoroughly cleaned inside before use (e.g. by blowing through with compressed air).
Pipes must be fixed in their correct position. The fixing clips must go right round the pipe. They may be of plastic, metal or rubber.
Observe adequate distances between the various fixing elements. As a rule a maximum distance of 500 mm for plastic pipes and
600 mm for metal pipes is applicable.
For plastic pipes, in order to prevent distortion and tension on the connectors when fitting them, take the necessary precautions
when working out the run and fitting the fixing brackets onto the chassis. Correct fitting of the fixing brackets will ensure that the
pipes do not rub against the fixed parts of the chassis.
Observe the necessary safety distances from moving parts and heat sources.
When a pipe has to pass through the chassis frame (side or cross members) appropriate precautions must be taken to avoid damage.
A solution which can be used as a bulkhead connection for a straight or angled run is given in Figure 2.23:
Figure 2.23
91464
1. Pipe - 2. Bulkhead connector - 3. Chassis
After completing any work either on the system or the equipment, the braking system must be
! checked to ensure its efficiency.
For air systems, build up the pressure to its maximum value. Check for leaks in the areas affected by
the work carried out.
To ensure that the connections have been made correctly, the air reservoir for one axle may be discharged. This check can be perfor-
med by reading the on-board gauge and, by working the brake pedal, by checking the pressure in the remaining brake section (or
sections).
In hydraulic circuits, on completing the work, the normal air bleeding operation must be performed.

2.15.3 Electronic braking system control devices
For any changes to the electrical circuits, read carefully chapter 5.

!
When modifying the wheelbase, the ABS modulators must be kept in their original position in relation to the rear axle. The
electrical wires (harness) between the sensors on the rear axle and the control unit and between the control unit and modulators
must be modified accordingly by fitting the harness(s) from a longer wheelbase IVECO vehicle should there be insufficient length
in the originals. Brake pipes upstream of the modulators must be similarly modified.
2.15.4 Taking air from the system
In vehicles with an air braking system it is possible to obtain small amounts of air from the air tank in the auxiliary circuit. Air
should only be taken in through a reflux valve that is able to prevent tank pressure dropping to below 8.5 bars in the service brake
circuit and auxiliary circuit.
Air must be taken in directly behind the brake system four circuit protection valve (output 24).
In the Stralis series, air may be taken in directly on the valve plate on connection 5 unless this is already in use (see Figure 2.24).
Figure 2.24
116722
If larger quantities of air are required a supplementary air reservoir must be fitted. In this case, it will be necessary to check that the
air compressor fitted is capable of charging the brake system reservoirs within the prescribed times.
If necessary a larger capacity compressor must be fitted.

Repositioning Parts and Mounting Auxiliary Assemblies and Equipment
2.16 Electrical System: Modifications and Drawing-Off Power
NOTE Subject moved to chapter 5.5
2.17 Repositioning Parts and Mounting Auxiliary Assemblies and Equipment
Whenever, in the course of modifying the vehicle, it should become necessary to reposition assemblies such as the fuel tank,
batteries or the spare wheel, such relocation is permitted provided that the functioning of these parts is not impaired and provided
that the same type of connections as originally in use are re-employed. Their transversal location on the vehicle’s chassis may not,
when their weight requires it, be changed radically.
In the case of vehicles not equipped with a spare wheel carrier, and vehicles in which the spare wheel carrier must be relocated,
the spare wheel must be secured to a suitable wheel carrier which allows the wheel to be readily removed.
To secure the spare wheel to the side of the vehicle with a support attached to the web of the side member, it is advisable to use
a reinforcing plate on the inside or outside of the side member. The size of this plate must take into account both the weight of
the wheel and the possible presence of other reinforcements on the side member (see Figure 2.25).
Figure 2.25
91470
In order to limit the torsional stresses on the vehicle chassis, we recommend that the plate be fitted where there is a cross member,
particularly in the case of heavy units.
A similar procedure should be adopted when fitting additional units such as tanks, compressors etc. When positioning them, due
consideration must be given to the distribution of the weights (see point 1.13.3).
In any event, an adequate distance of their height from the ground must be ensured with due consideration given to the use of the
vehicle.
It is advisable to take measures to reinforce the frame depending on the weight of the construction parts. On request, Iveco is able
to provide further information on this topic.
Any holes that are necessary for the relocation must be made on the web of the side member in accordance with the specifications
given in point 2.3 Holes already present must be made use of to the greatest extent possible.
When tank refilling is hindered by the positions of the body structure, the tank mounting brackets may be installed one drilling unit
lower (45 mm).

Supplementary fuel tank

If a supplementary fuel tank is to be added, the best solution is to use the same system arrangement already used for original
fuel tank, using, whenever possible, original elements. The use of a switching system allows the alternative feeding from the two tanks
(see Figure 2.26).
Figure 2.26
91471
The use of the above system is advisable when the added tank is located on the side opposite the original one. When the tanks
are in line on the same side it is possible to maintain fuel feed from the original tank then the added one should be connected directly
to the former through hoses. The arrangement must conform to national rules and regulations. The tank-to-tank connecting line
must be leakproof and not of a smaller internal dimension, have the same technical characteristics as those envisaged for the original
system and be properly secured.
Table 2.22 - Stralis AT-AD, Cursor 8 engines, available tanks

Fuel tanks
Model Engine 200L 300L 400L 600L 800L 800L+400L
Plastic Aluminium Aluminium Aluminium Aluminium Aluminium
S27
AT-AD190S S30 standard opt 6170 -
AT AD190S/P
AT-AD190S/P opt 6172 opt 6173 opt 6177
AT-AD190S/FP-D
AT AD190S/FP D S31
S35 - standard opt 6172
AT AD440ST/P
AT-AD440ST/P S31 -
- standard opt 6172 opt 6173 opt 6177
AT-AD440ST/P - HR S35 opt 7855
S27
AT-AD260SY/PT
AT AD260SY/PT standard opt 6170 -
S31 opt 6172 opt 6173 opt 6177
AT-AD260SY/TN
S27
AD260SX/P S30 - - - - - -
AD260SX/FP
S31
S27
AT-AD260SY/P
AT AD260SY/P
AT-AD260SY/PS
AT AD260SY/PS S30 standard opt 6170 -
opt 6172 opt 6173 opt 6177
AT-AD260SY/FP-D S31
AT AD260SY/FS D
AT-AD260SY/FS-D

Table 2.23 - Stralis AT-AD, Cursor 10 engines, available tanks

Fuel tanks
Model 300L 400L 600L 300L+300L 800L 600L+300L 800L+400L
Aluminium Aluminium Aluminium Aluminium Aluminium Aluminium Aluminium
AT-AD190S
AT-AD190S/P standard opt 6172 - opt 6177 - opt 7855
AT-AD190S/FP-D
AT-AD190S/FP-CT - - - standard - opt 7854 -
AT-AD440ST/P
standard opt 6173 - - opt 7855
AT-AD440ST/P - HR
AT-AD440ST/P - LT - - - standard - opt 7854 -
AT-AD440ST/P - CT
AT-AD260SY/PT
standard opt 6172 opt 6173 - opt 6177 - opt 7855
AT-AD260SY/TN
AT440S43TZ/P standard opt 6172 opt 6173 - - - -
AT-AD260SY/P
AT-AD260SY/PS
AT-AD260SY/FP-D standard opt 6172 opt 6173 - opt 6177 - opt 7855
AT-AD260SY/FS-D
AT-AD260SY/FS-CM

Transporting hazardous goods ADR
2.18 Transporting hazardous goods ADR
Vehicles used to transport dangerous Goods - for instance inflammable materials or explosives - must be built in compliance
with the safety specifications established for this type of transport by national or international regulations.
Stralis vehicles may be fitted with option 2342 (ADR) in combination with option 8818 (Digital Tachograph for ADR).
The optional 2342 consists of:
- special electric disconnector positioned on frame.
- Disconnector control switch positioned in cab.
- Emergency switch.
- Protected electrical connections.
- Wiring protected using polyamide sheath.
- ADR type approval plate.
- Operating instructions.
If option 2342 is fitted, central door locking is not available.
On the assumption that the Bodybuilder is aware of, and in compliance with, the particular specifications relative to this subject we
would like to recall, nonetheless, that all vehicles crossing borders within Europe must be in compliance with the ”European Agree-
ment on international transport of dangerous substances on roads” (ADR), now included in the specific EC Directive.
As a case in point, we list below some of the requirements in the above mentioned Agreement (ADR), which in any case must be
carefully examined:
1) Electrical equipment.
Electric wiring must be suitably insulated and protected in conduits from impact, stones, heat etc.
Circuits must be protected against overloads by fuses or automatic disconnectors.
A general circuit breaker (excluding the tachograph supplied directly by the batteries) with suitable safety devices, located close
to the batteries, with direct or remote control in the cab or outside.
2) Braking:
Compliance with the specific EC Directives.
Anti-lock braking system (ABS) and retarder compulsory in the cases required by the law.
3) Protection of the cab.
Use of virtually flameproof materials, in conformity with ISO 3795, with combustion speeds no greater than 100 mm/min. Other-
wise, have a protective wall between the driver’s cab and the transported container.
4) Exhaust system.
Those parts of the exhaust system which reach temperatures of more than 200ºC and cannot be moved in front of the protec-
tive wall, must be adequately insulated.
If the exit of the exhaust cannot be turned outwards, in the case of tranporting explosives, it must be equipped with a spark
arresting device.
(If any modifications of the exhaust pipes are necessary, they must be carried out in accordance with point 2.9).
5) Fuel tank.
This needs to be positioned so it is protected against bumps. In the event of it over turning or of leakage, the liquid has to run
off straight onto the ground.

6) Independent heater.
This must be safe as regards fire protection. It has to be positioned in front of the cab rear panel, at least 80 cm off the ground,
with the heated parts protected.
7) Speed limiting device.
Compulsory for vehicles with GVW greater than 12 m.t., in compliance with current EC Directives and set to 85 km/h.
8) Safety equipment.
A minimum of two fire extinguishers, two portable lamps that are independent from the electrical system of the vehicle, and
whose operation cannot cause the combustion of the cargo being transported.
9) 3rd axle.
The electric lifting device for the 3rd axle has to be positioned outside the side members of the chassis frame, in a watertight
box.
Check the availability of these outfits for our models with IVECO.

Retarder installation
2.19 Retarder installation
Retarder brakes other than those supplied as options cannot be fitted on Stralis.
! IVECO does not allow fitting any type of retarder brake system after-market.
For this reason, no approval will be given for the application of retarder brakes.
Any unauthorised interventions or changes concerning brake functionality will void the vehicle warranty.
Retarder installation
Modifications to the Rear Underrun
2.20 Modifications to the Rear Underrun
Our vehicles are fitted with a rear underrun bar in accordance with EC Directive.
The maximum permitted distance from the bar to the rearmost part of the body is 400mm. For further information see the official
information issued by IVECO.
Whenever chassis modifications affect the rear overhang, the underrun bar must be repositioned (in compliance with current regula-
tions) so as to be able to obtain the same connection with the chassis as on the original vehicle.
When modifying the vehicle or installing special equipment (e.g. tail lifts) it may be necessary to modify the structure of the underrun
bar. Such modifications must not change the original resistance and stiffness specifications (comply with local government regulations,
if any). The firm carrying out the modification must be prepared to present the relevant documentation on the required specifica-
tions upon request.
Whenever a different underrun bar must be used, check relevant current regulations. Documentation or quality control certificates
must be presented upon request from the competent authority.
Modifications to the Rear Underrun

Rear Mudguards and Wheel Boxes
2.21 Rear Mudguards and Wheel Boxes
When vehicles are supplied without mudguards, the bodybuilder must fit them using similar installations are used by IVECO on
similar vehicles. The following points must be observed:
- Ensure the wheels can turn without any foul conditions even in the full bump condition with snow chains fitted, in compliance
with the limits shown in the documentation supplied by IVECO.
- On vehicles with lifting axles sufficient space must be allowed for the axle to fully lift without the tyres fouling any structure,
following the instructions given the relevant documentation.
On the 6x2/PS and FS (Steering Version 2)the axle also steers when the axle is raised, therefore sufficient space must be allowed
for this function as shown in Figure 2.27. The dimensions shown refer to 315/80R22.5 tyres, allow another 50 mm if 385/65R22.5
tyres are fitted.
- The maximum width of the vehicle over the tyres must comply with the legal limits.
Figure 2.27
116725
When fitting mudguards or making whell boxes the following points should be considered:
- The supporting structure should be sufficiently strong enough, avoiding any sudden variation in section.
- If the supports are fixed to the web of the sidemembers they must be bolted, the sidemembers must not be welded (see Figure
2.28).
If the supports are fixed the body longitudinals they can be welded or bolted.
Figure 2.28
116726
Rear Mudguards and Wheel Boxes

Mudflaps
2.22 Mudflaps
If legally required, unless already fitted ex-factory, the bodybuilder must ensure that the complete vehicle is fitted with mudflaps.
When mounting them legally required distances must be complied with.
Mudflaps
Side Guards
2.23 Side Guards
In some countries local or EC regulations require that the vehicle be fitted with side guards. The Bodybuilder who finishes off
the vehicle must ensure compliance with the required characteristics unless it is already equipped with them ex-factory.
On permanently fitted structures such as fixed platform bodies, vans etc, the side guards will be fitted directly to their basic structure
(floor ribbings cross members) whereas on mobile structures (such as tippers, interchangeable equipment, removable containers),
the side guards will be connected to the auxiliary frame by way of suitable brackets or installed directly on the chassis. In the latter
case, we suggest that the Bodybuilder makes use as far as possible, of the holes already existing on the side member vertical web
in compliance with point 2.3.
According to the EC regulation, the external protection element can either consist of a single runner whose surface extends in the
vertical direction or of several longitudinal sections with preset sizes and distances between them.
The side guards must be connected to their own supporting structures in order to allow quick removal or tilting should maintenance
or repair work on assemblies or components located next to them be needed.
Operation of and access to the following parts must be ensured:
- Brake system equipment.
- Air inlet system
- Fuel supply.
- Batteries.
- Suspension.
- Spare wheel.
- Engine exhaust.
The guards must be made of the appropriate materials (e.g. FeE420).
Particular care must be taken when fitting to ensure the clearance from the ground and the distances to the various components
required by the regulations.
In Figure 2.29 shows a type of side guard designed in compliance with the relevant EC Directive to be fitted to fixed bodies (available
on request). The illustration also shows a specimen of a support designed for the combined fastening on the side guard and the
rear wheel mudguard which can be fitted to mobile auxiliary subframes.
The Bodybuilder will take care of the preparation and the arrangement of the side guard depending on the type of auxiliary subframe
concerned, as it is not possible to provide instructions of a general character applying to all equipment versions.
Side Guards
Figure 2.29
Section A-B Detail “X”
A For IVECO section

B Either the bottom part of the auxiliary frame is over 1,300 mm from the ground
or the width of the auxiliary subframe is less than the external space occupied
by the tyres.
C Test load 1 kN Permitted sag values under test load:
≤ 30 mm on the rear, included in the last 250 mm of the device
≤ 150 mm on the remaining parts of the device
D Supporting structure for the combined
fastening of the side guard and rear mudguard.
D
116727
Side Guards
Chocks
2.24 Chocks
Usually these are fitted directly at the factory. Should this not be the case, or if it is necessary to change their original position,
the Bodybuilder must work out a new arrangement in compliance with local regulations. The new position must ensure reliability
and safety as well as easy access for operation by the user.
Chocks
Chocks
STRALIS AS/AT/AD Euro 4/5 BUILDING & MOUNTING THE STRUCTURES 3-1
Index
SECTION 3
Building & Mounting the structures
Page
3.1 Subframes and Bodies 3-3
3.1.1 Material (steel subframe) 3-3
3.1.2 Material (Aluminum Subframe) 3-4
3.1.3 Longitudinal section dimensions 3-5
3.2 Elements making up the subframe 3-6
3.2.1 Longitudinal Runner Profiles 3-6
3.2.2 Cross Members 3-9
3.3 Connections between frame and subframe 3-11
3.3.1 Choosing the Type of Body Mounting 3-11
3.3.2 Body Mounting Characteristics 3-11
3.3.3 Connection with Brackets 3-12
3.3.4 Connection with Greater Elasticity 3-13
3.3.5 Connection with U-bolts (clamps) 3-14
3.3.6 Connection with cleate (shear resisting) plates to contain longitudinal and transverse forces 3-15
3.3.7 Mixed Connection 3-16
3.4 Fitting Box-bodies 3-17
3.4.1 Fixed bodies 3-17
3.4.2 Tipper Bodies 3-20
3.4.3 Heavy-duty Service 3-22
3.4.4 Light-duty Service 3-22
3.4.5 Containers 3-23
3.5 Tractors for Semitrailers 3-24
3.5.1 Position of the Fifth Wheel 3-24
3.5.2 The Fifth Wheel 3-24
3.5.3 Coupling of Tractor and Semitrailer 3-24
3.5.4 Fifth Wheel Mountings 3-26
Index
3-2 BUILDING & MOUNTING THE STRUCTURES STRALIS AS/AT/AD Euro 4/5
Page
3.5.4.1 Preparation and installations of a Structure Working together with Chassis 3-32
3.5.4.2 Converting a Truck into a Semitrailer Tractor 3-34
3.5.4.3 Variable height fifth wheel (only for Low tractor) 3-34
3.6 Transport of Indivisible Materials (bascules) 3-35
3.7 Installation of Tanks and Containers for Bulk Materials 3-36
3.8 Installing a crane 3-39
3.8.1 Crane Behind the Driver’s Cab 3-40
3.8.2 Crane on Rear Overhang 3-43
3.8.3 Removable Cranes 3-45
3.9 Installation of Tail Lifts 3-46
Index
3333.3
Subframes and Bodies
NOTE The following detailed instructions complement the general information given in Chapter 1.
3.1 Subframes and Bodies
The purpose of an subframe (subframe) is to ensure a uniform distribution of the load on the vehicle’s chassis and to increase
the strength and rigidity of the main frame in relation to the particular use of the vehicle.
The following points are to be borne in mind when constructing a subframe:
3.1.1 Material (steel subframe)
Usually, provided the subframe is not to undergo great stress, the material used for its construction may be of a lower grade
than that used for the vehicle chassis. It must have good welding characteristics and limits of no less than valoes (1) shown in Table 3.1.
Should the stress limits require it (e.g. if cranes or tail lifts are to be fitted), or if very high sections are to be avoided, material with
better mechanical characteristics may be used. In this case it should be considered that a lower inertia moment of the reinforcing
beam implies high bending stresses on the chassis frame.
The properties of some materials that can be considered for the applications indicated are as follows.
Table 3.1 - Material to be used for body manufacturing continued

Breaking load Yield point
Steel name Elongation A5
(N/mm2) (N/mm2)
IVECO FE360D
EUROPE S235J2G3
360 (1) 235 (1) 25% (1)
GERMANY ST37-3N
UK 40D
IVECO FEE420
EUROPE S420MC
530 420 21%
GERMANY QSTE420TM
UK 50F45
IVECO FE510D
EUROPE S355J2G3
520 360 22%
GERMANY ST52-3N
UK 50D

3.1.2 Material (Aluminum Subframe)
In the case of materials, having different characteristics compared to steel, such as aluminium, both the dimensions and the struc-
ture of the subframe will have, as a rule, to be adapted accordingly.
When the subframe’s main function is mainly to distribute the load more evenly while leaving the major loadbearing to the frame,
aluminium longitudinal runners can be used having the same dimensions as stated for the steel. Some typical examples are: fixed
bodies, box bodies, tanks with continuous and close spaced bearers or bearers mounted directly over the suspension hanger brack-
ets. Exceptions are those cases where the high stresses on the vehicle’s frame demand steel runners of a high dimension or shear-re-
sistant connections.
When the subframe must contribute in terms of strength and stiffness (bodies having high concentrated loads, such as tippers, cranes,
central axle trailers, etc.) aluminium is not recommended and has therefore to be authorised for each application.
It should be remembered that, when stating the minimum dimensions for the reinforcement runners, besides the admitted limit of
stress for the aluminium, the different elastic modulus compared to steel (approx. 7,000 kg/mm2 as against 21,000 kg/mm2 for steel)
will also have to be considered. This will result in larger dimensions for the runners.
Similarly, when the connection between frame and counterframe guarantees the transmission of shearing forces (connection via
plates), a new neutral axis must be defined for the section based on the different elastic modulus of both materials when checking
the stresses at both ends of the single section.
In the final analysis, if the subframe has to contribute to the frames Strength / stiffness, higher sectional dimensions for the runners
must be used if aluminum in to be used instead of steel.

3.1.3 Longitudinal section dimensions
The table below gives the values for the section modulus Wx for C-section longitudinals recommended by IVECO. The indicated
Wx value refers to the true section and allows for the section radii (this can be calculated with some approximation by multiplying
the value obtained when considering the section made up of simple rectangles by 0,95). Longitudinals of different sections can be
used instead of those shown provided the section modulus Wx and the moment of inertia Jx of the new C-section are not lower
than those shown in the table.
Table 3.2 - Section bar dimensions

Strength modulus Recommended C-section profile
Wx (cm3) (mm)
16 ≤ W ≤ 19 80 X 50 X 4 80 X 60 X 4 80 X 50 X 5
20 ≤ W ≤ 23 80 X 60 X 5
24 ≤ W ≤ 26 80 X 60 X 6
27 ≤ W ≤ 30 80 X 60 X 7 100 X 50 X 5
31 ≤ W≤ 33 80 X 60 X 8 100 X 60 X 5
34 ≤ W ≤ 36 100 X 60 X 6
37 ≤ W ≤ 41 100 X 60 X 7
42 ≤ W ≤ 45 80 X 80 X 8 100 X 60 X 8
46 ≤ W ≤ 52 120 X 60 X 6 120 X 60 X 7
53 ≤ W ≤ 58 120 X 60 X 8
59 ≤ W ≤ 65 140 X 60 X 7 120 X 70 X 7
66 ≤ W ≤ 72 140 X 60 X 8 120 X 80 X 8
73 ≤ W≤ 79 160 X 60 X 7
80 ≤ W ≤ 88 180 X 60 X 8
89 ≤ W ≤ 93 106 X 70 X 7 180 X 60 X 7 140 X 80 X 8
94 ≤ W ≤ 104 180 X 60 X 8
105 ≤ W ≤ 122 200 X 80 X 6 200 X 60 X 8 180 X 70 X 7
123 ≤ W ≤ 126 220 X 60 X 7
127 ≤ W≤ 141 220 X 60 X 8
142 ≤ W ≤ 160 200 X 80 X 8 240 X 60 X 8
161 ≤ W ≤ 178 220 X 80 X 8 240 X 70 X 8
179 ≤ W ≤ 201 250 X 80 X 7 260 X 70 X 8
202 ≤ W ≤ 220 250 X 80 X 8 260 X 80 X 8
221 ≤ W ≤ 224 220 X 80 X 8 280 X 70 X 8
225 ≤ W ≤ 245 250 X 100 X 8 280 X 80 X 8
246 ≤ W ≤ 286 280 X 100 X 8
290 ≤ W ≤ 316 300 X 80 X 8
316 ≤ W ≤ 380 340 X 100 X 8
440 380 X 100 X 8
480 400 X 100 X 8

Elements making up the subframe
3.2 Elements making up the subframe
3.2.1 Longitudinal Runner Profiles
The longitudinals of the added structure must be continuous, extending as far as possible forward to the front of the vehicle
to include, if possible, the area of the rear support of the front spring, and rest on the chassis of the vehicle but not on the brackets.
In order to achieve a gradual reduction in the resistant section, the front ends of the longitudinal runner must be tapered upwards
at an angle of no more than 30°, or tapered in some other equivalent way (see Figure 3.1), ensuring that the front end in contact
with the chassis is suitably connected, min radius 5 mm.
Figure 3.1
91136
If the cab’s rear suspension components do not allow the entire runner to pass through, the latter may be shaped as shown
in Figure 3.2. If the front part of the frame is subject to strong bending moments for certain types of construction (e.g. in the case
of a crane with its working field at the front), the installation profile must be upgraded to take into account these forces
Figure 3.2
91137
The construction of auxiliary frames either wider or narrower than the chassis structure is permitted only in particular cases
(e.g. removable containers sliding on rollers operated by mechanical or hydraulic systems). In these cases a necessary precaution
will be that of ensuring a correct transmission of the forces between the auxiliary frame and the side member vertical web. This
can be obtained by inserting an intermediate runner profile shaped according to the vehicle’s side member or by applying a stiffened
connecting L-section.

The vehicle chassis is shaped and therefore the subframe runner profile must follow the shape of the main side members. Should
the front part of the subframe be narrower than the chassis, either a number of suitably shaped U-sections or of angle L-sections
with the appropriate gussetts can be installed on the outside of the subframe (see Figure 3.3).
Figure 3.3
A
B
91138
A. L section - B. Alternative solution - C. Channel section

The type of section of the runner must be determined with due consideration to the function of the subframe and to the type
of structure that is above it. It is advisable to use open U-sections if the subframe has to adapt itself elastically to the vehicle’s chassis,
and to use box-type sections when added rigidity is needed.
Proper care must be taken to ensure a gradual change from the box- type section to the open type section. Some examples on
how this can be achieved are shown in Figure 3.5.
NOTE Cleat plates must not be used at the profile section of the sidemembers.

Figure 3.4
Version “A” Standard box-type Gradual change from box-

runner profiles type to open-type section
“A”
“B”
Special combined
section runner profiles
Chassis/subframe connecting
Version
angle section
“C”
Version “F”
15mm platband (width equal

to runner profile flange) Angle section thickness
equal to subframe
runner profile)
“D”
Version “G”
“E”
There must be continuity between the longitudinal runners of the subframe and the vehicle. Where this is not possible, continuity
may be restored by fitting cleat plate brackets.
If a rubber antifriction strip is inserted, specifications and thickness must be equal to those originally used by the Manufacturer (hard-
ness 80 Shore, max. thickness 3mm). The application of antifriction material may prevent abrasive actions which can cause corrosion
when using material with a different composition (e.g. aluminium and steel).
The minimum recommended dimensions are shown for the sidemembers with various bodies. These values are generally valid for
vehicles with standard wheelbase and rear overhang (see Tables from 3.4 to 3.21). In all cases similar sections, whose moment of
inertia and resistance is not lower, can be used. It should be borne in mind that the moment of inertia, apart from being an important
factor for the calculation of the share of bending moment to be applied, also represents the most adequate response to the degree
of torsional stress required for the specific type of connecting section in use. Therefore, the moment of resistance is a determining
factor as regards the stress exerted on the material.

3.2.2 Cross Members
An adequate number of cross members, which should be positioned if possible adjacent to the body mounting brackets, are
required to brace the two runners of the subframe.
The cross members may be of the open type (e.g. C-type) or, if greater rigidity is desired, of the closed box-type.
Suitable gusset plates must be used to connect the crossmembers to the longitudinals to ensure sufficient strength at the connection
(see Figure 3.5). In cases, where greater rigidity is required for the connection, this can be achieved as illustrated in Figure 3.6.
Figure 3.5 Figure 3.6
Stiffening the Subframe
In the case of certain bodies, such as tippers, cement mixers, crane on rear overhang or bodies with a high centre of gravity,
the subframe must be additionally stiffened at the rear end.
Depending on the degree of torsional stress, this must be done in one of the following manners:
- Joining the rear section of the longitudinal member by a box-frame construction.
- Box-frame construction, closed-section cross members (see Figure 3.7).
- Box-frame construction, whit a cruciform (see Figure 3.8).
- By applying in addition to the box-frame construction a longitudinal torsion-resistant bar (see Figure 3.9).
As a general rule, the box-frame construction of the longitudinal runners should not be used in the front end.
Figure 3.7

Figure 3.8
1. Subframe - 2. Cruciform
Figure 3.9
1. Subframe - 2. Box-section
Self-supporting Bodies as Subframes
A subframe (longitudinal runners and cross members) need not be fitted if self-supporting bodies are to be installed (e.g. rigid box
body, tankers), or if the base of the structure to be fitted already serves the purpose of a subframe.

Connections between frame and counterframe
3.3 Connections between frame and subframe
3.3.1 Choosing the Type of Body Mounting
The selection of the type of connection to be used - if not provided initially by IVECO - is very important in terms of the subframe
providing strength and stiffness for the appropriate body type.
The subframe connection may be flexible (brackets or clamps) or it may be rigid, resistant to shear stress (longitudinal or transverse
plates); the choice must be made based on the type of body that is to be mounted (see points 3.4 to 3.8) analysing the stress forces
which the additional equipment transmits to the chassis both under static and dynamic conditions. The number, size and type of
fixing device properly subdivided over the length of the subframe, must be such as to ensure a good connection between the vehicle
chassis and the subframe.
The screws and clamps must be of a strength class no lower than 8.8, the nuts must be equipped with devices that prevents them
from working loose. The first fixing must be located, if possible, at a distance of approx. 250 to 350 mm from the front end of the
subframe.
Any body fixing brackets already fitted on the vehicle frame must be used first.
Compliance with the position for the first mounting mentioned above must be ensured in cases where the body applies concentrated
loads behind the cab and requires additional stability (e.g. cranes, front end tipping gears etc.) in order to prevent overstressing the
chassis frame. If necessary, additional fixings must be fitted.
If the body to be fitted has different characteristics to those permitted on the original chassis (e.g tipper on a haulage chassis), the
bodybuilder must provide the appropriate mountings (e.g. the replacement of brackets by cleat plates in the rear area of the chassis).
NOTE When fixing the body to the frame, no welding is allowed on the frame of the vehicle, nor can holes
be drilled in the flanges of the sidemembers.
When fixing the body to the frame, no welding is allowed on the frame of the vehicle, nor can holes be drilled in the flanges of
the sidemembers.
In order to improve the longitudinal or transverse securing of the connection, it is permissible to have holes in the top flanges of
the side members, but only at the rear end of the members, over a length of not more than 150 mm, providing the fixing of any
cross members that may be present is not weakened (see Figure 3.14). The mountings shown in Figure 3.15 may be used, using
the screws which connect the rear cross member or underrun brackets to the chassis.
NOTE In all other cases, holes must not be drilled in the flanges of the sidemembers.
In all other cases, holes must not be drilled in the flanges of the sidemembers.
3.3.2 Body Mounting Characteristics

Flexible mountings (see Figure 3.10, 3.11, 3.12 and 3.13) permit limited movement between the frame and the subframe, and
permit the use of two parallel working strong sections. Each bears a part of the bending moment in proportion to its moment of
inertia.
For the rigid type of joint (see Figure 3.15) between subframe and chassis, a single strong section is obtained, provided the number
and position of the mountings are adequate to support the resulting shear stresses.
When using sheer resisting plates to secure the subframe to the sidemembers, a single strong section is formed which has a higher
strength capacity when compared with the MTG made using brakets or clamps. This has the following advantages:
- Lower height of the subframe profile under the same bending moment acting on the section.
- Higher bending moment under the same subframe profile dimensions.
- Further increase in the strength capacity, when the subframe is made up of high mechanical characteristic materials.

3.3.3 Connection with Brackets
A few examples of this type of connection (flexibility mounting), are shown in Figure 3.10.
Figure 3.10
A
A. Leave a clearance of 1 to 2 mm before tightening
1. Subframe - 2. Frame - 3. Shims

In order to ensure a flexible joint there must be a gap of 1 to 2 mm between the brackets on the frame and those on the subframe
before the securing bolts are tightened. Larger gaps are to be reduced by using suitable shims. Using bolts of proportional length
improves the flexibility of the connection.
The brackets must be secured to the web of the vehicle’s side member only by means of bolts or rivets.
In order to guide and better contain the loads transversally, a slight protrusion of the brackets above the chassis is recommended.
When the brackets are fitted flush with the upper flange of the side member, the lateral movement of the body structure must be
secured by other means (e.g. using guide plates fixed only to the chassis - see Figure 3.13). When the front connection is of the
coli springstype (Figure 3.11), longitudinal securing must be ensured even in conditions of maximum twisting of the chassis (e.g. off-
road).
When the chassis already has factory fitted brackets for the installation of a box-type body, these brackets must be used for the
installation of the structure. The brackets fitted to the subframe or to the body must have characteristics of strength no lower than
those of the original brackets fitted to the vehicle.

3.3.4 Connection with Greater Elasticity

Given that there is not a clear definition of range of torsion of the vehicle rigid structure, due to its tough mission, the structure
flexibility is always requested, except for special uses (e.g. installation of cranes). A coil spring should be used on each side of the
connection points between frame and sub-frame.
The detail of the body mounting and installation is as follows:
Figure 3.11
- Spring stiffness = 424 N/mm.

- With the longitudinal hard on the top flange there must be a grap of 5 mm between the faces of the two brackets before the
upper bracket is fixed to the longitudinal.
- The body securing bolt should be 14 mm diameter grade 8.8 and secured with lock nuts.
- Flat washers 4 mm thick by 32 mm outside diameter (minimum in both cases) should be fitted between the spring and the head
of the bolt and between the lock nut and frame bracket.
When using rubber inserts, use materials which gives a good working life (elasticity). The relevant instructions for the regular
inspections of the body mounting for deterioration and the bolt torque must be given to the operation.
Figure 3.12
1. Element rubber.
The whole connection capacity can, if necessary, be re-established by fitting shear resisting plates from the rear spring front hanger
brackets ti the end of the frame instead of the normal factory body brackets.
On installations where the vehicleis supported by means of hydraulic stabilisers (e.g. cranes, lifting platforms), the movement of the
elastic connection should be limited to 30 ÷ 40 mm to ensure sufficient coordinated movement of the subframe and avoid excessive
bending moments on the original chassis.

3.3.5 Connection with U-bolts (clamps)
The most important mounting of this type is illustrated in Figure 3.13.

In this type of construction the bodybuilder must place metal spacers, between the flanges of the two side members and in the
subframe at the point where the U-bolts are located, in order to prevent the flanges bending when the U-bolts are tightened.
In order to guide and contain transverse movement of the structure attached to the vehicle’s chassis, this type of connection must
also have guide plates that are attached only to the chassis as shown in Figure 3.13.
In order to keep the added structure from sliding and to increase the rigidity, it is necessary to provide positive attachment towards
the rear with cleat plates to contain both longitudinally and transversal movement.
Alternatively it is also possible to use bolt-type connections at the rear end of the chassis as illustrated in Figure 3.14.
Due to the nature of this type of connection, its all-round use on the vehicle is not advisable.
Figure 3.13
1. Frame - 2. Subframe - 3. U-bolts - 4. Locking with a lock nut -

5. Spacers - 6. Guide plates (where necessary)

Figure 3.14
1. Subframe - 2. Frame - 3. U-bolts - 4. Longitudinal transversal securing
3.3.6 Connection with cleate (shear resisting) plates to contain longitudinal and transverse
forces
This type of fixing shown in Figure 3.15 is achieved by means of a plate that is bolted or welded to the subframe and is secured
to the chassis by bolts or rivets. This ensures regeneration following longitudinal and transverse thrust and provides maximum rigidity
to the whole.
When this type of joint is used, the following must be observed:
- The plate must only be attached to the vertical web of the main sidemembers.
Before fixing ensure that the subframe is mounted correctly on the top flange with no gaps between the two mating surfaces.
- Use of cleat plates must be confined to the central and rear sections of the frame.
- The number of plates, thickness and number of securing bolts must be adequate for the transmission of the sections shear and
bending moments. As a rule the thickness of the plate will be equal to that of the vehicles sidemember. These values can be
correctly determined by calculation according to the necessary elements.
Good results can however be achieved taking the following into account:
The shear resistant plates and the omega brackets which are standard on some models are generally sufficient for normal bodies
such as fixed loading platforms, tilting bodies, concrete mixers, provided the conditions of paragraphs 3.3 and 3.4 are met and comply,
in terms of dimensions and positioning, with the normal bodies.
The shear resistant plates already fitted to the vehicles can on the other hand meet the requirements of all installations which cause
small bending moments on the vehicle frame (e.g. tail lifts, reduced capacity cranes).

When a body cause high bending moments on the frame and the relevant strength has to be increased by means of shear resistant
plates between the frame and subframe, or the subframe height has to be limited as far as possible (e.g. towing of central axle trailers,
crane on rear overhang, tail lifts), observe the following instructions:
Table 3.3
Frame/subframe Max. distance between the Min. characteristics of the plates

section
ti h height
i ht ratio
ti centreline
t li off the
th shearing
h i
Thickness Fixing hardware
resistant plates 1)
(mm) dimensions (at least 3
screws each plate) 2)
≤1.0 500 8 M 14
NOTE Table applies to all models
1) The number of bolts per plate enables a proportional increase in the distance between the plates (a double number of bolts enables greater distance between
the plates). In the bearing areas of the frame (e.g. supports of the rear spring, of the tandem axle spring and of the rear air springs) closer spaced plates will
have to be considered.
2) In case of limited thickness of both of the plates and the subframe, the connection should be carried out by means of spacers, so that longer bolts can be used.
Figure 3.15
3.3.7 Mixed Connection
On the basis of instructions given for the construction of the subframe (point 3.1) and considerations included in the general section,
the mounting between the vehicle frame and subframe can be of the mixed type, i.e. it may be obtained through a rational use of elastic
(springs), flexible connections (brackets, clamps) and rigid connections (plates for longitudinal and transversal anchorage).
As a guide it is advisable to have coli springsconnections on the front section of the subframe (at least two on each side) while plate
connections are recommended for the rear section of the vehicle when a stiffer structure is required for the whole assembly.

Fitting Box---bodies
3.4 Fitting Box-bodies
3.4.1 Fixed bodies
See table in Chapter 1 to find out the volumetric weights required to determine the load distribution.
On standard cab vehicles, intended exclusively for road use, box- bodies are usually fitted on a support structure comprising longitudi-
nal runners and cross members. The minimum dimensions of the longitudinal runners are specified in Table 3.4.
Table 3.4 - (for models of class AS 190 up to AS 260, the data given below apply to loads on front axle up to 8000 kg).
Wheelbase (mm) Minimum reinforcing runner

(referring to the driving axle,
axle on
Models Section modulus Wx
vehicles with 3 axles with third
rear axle) (cm3)
AS/AT/AD 190; AS 1902)4) p to 63002)
up 893)
AS/AT/AD 260 up to 60502) (46)1)
1) Possible alternatively, using shear resistance connections for the entire length of the chassis and connection with brackets in the front area.
2) For vehicles with wheelbase up to 5700 mm and rear overhang up to 2300 mm, 120x60x6 mm section can be used (Wmin. 46 cm3); this profile is sufficient
for all 2 and 3 axle models up to 7500 kg on front axle.
3) For models with pneumatic suspension (190P; FP) with wheelbase up to 6300 mm and rear overhang over 2300 mm. When the maximum permitted rear
load is used, the longitudinal runner must use materials with a yield of over 320 Nm/mm2 and be connected to the chassis by shear resistant plates (cleat plates).
The plates should start approximately 1000 mm before the centre line of the drive axle and continue to the end of the chassis.
4) For models 6x2 P; FP; PS; PT; FT; with a rear overhang over 1800 mm (from the centre line of the last axle). When the maximum permitted rear axle load
is used, the longitudinal runner must be connected to the chassis by shear resistant plates. The plates should start approximately 1000 mm before the centre
line of the drive axle and continue to the end of the chassis.
5) For section dimensions see Table 3.2
The attachment is carried out using the brackets arranged on the vertical web of the side members. If such brackets have not
been provided by Iveco, they must be installed according to the specifications given in point 3.3. In order to provide an adequate
lengthwise securing when brackets or clamps are used, it is good common practice to arrange a rigid joint (one on each side) on
the rear overhang, using cleat plates on the web or bolts on the upper flange of the side member (see Figure. 3.14 and 3.15).
The front of the body must be able to withstand the force applied to it by the transported load during sharp braking.
Fitting Box-bodies
Under no other circumstances may new holes be made in the flanges of the main side members.
In those instances in which the box-body uses supports that are raised above the subframe (such as cross members) it will be necess-
ary to stiffen these supports in an appropriate manner in order to contain the longitudinalwise thrusts, as shown in Figure 3.16
Figure 3.16
1. Subframe - 2. Brackets - 3. Securing anchorages

For special builds when a reinforcing runner of limited height is needed, the subframe structure may be integrated with the body
anchoring brackets matching the height of the whole longitudinal reinforcement runner (see Figure 3.17). In this case, rear wheel
boxes may be fitted at the base of the fixture.
Fitting Box-bodies
Figure 3.17
In the case of self-supporting bodies whose bearing structure operates as a subframe, the above explained installation of the
reinforcing runners need not be affected.
The application of box bodies and structures with high torsional (1), stiffness in general requires the use of elastic connections to-
wards the front of the structure (2) to avoid excessive reduction of main chassis distortion in particularly demanding applications
(3).
1) Es. vehicle preparation furgonato
2) Figures 3.11 and 3.12
3) In the anterior part they are had to apply plates that limit the side move of the superstructure in comparison to the chassis.
Fitting Box-bodies
3.4.2 Tipper Bodies
The use of tipping bodies, whether front end or three way, subjects the chassis to notable stress. For this reason it is most import-
ant to select the right vehicle from among those intended for this use. Therefore we list here the specifications that must be adhered
to for this type of construction subdivided according to light or heavy duty; in the Table 3.5 give the minimum runner dimensions
for the subframe with which these vehicles must be equipped.
Furthermore any government regulations concerning these vehicles must also be adhered to.
Where Iveco offer a rear stabilizer bar as an option it is recommended this should be fitted.
The following points must be kept in mind:
- The subframe must be (see Figure 3.8 and 3.9) suitable for the vehicle type and for the specific operating conditions. It must
have adequately dimensioned longitudinals and cross members and be stiffened at the rear by box-type construction and cruci-
form.
Fixing the subframe to the chassis, flexible connections (brackets or clamps) must be placed at the front end, whereas the rear
section requires rigid-type joints (cleat plates, see Figure 3.16) to allow the added structure to contribute more to the rigidity
of the whole. The ”omega” brackets can be used on vehicles which are already fitted with them.
- The rear tipping hinge must be fitted on the subframe as near as possible to the rear support of the rear suspension. In order
not to impair the stability of the vehicle during tipping operations and not to increase excessively the stress on the chassis, it
is recommended that the distances between the tipping hinge and the rear spring rear hanger or tandem centreline is observed
(see Figure 3.21). If for technical reasons this cannot be achieved, small increases may be permitted provided a higher strength
subframe is used, in order to increase the rigidity of the rear end. Where long bodies are needed to transport large volumes,
it is advisable (in those cases where it is permissible) to lengthen the wheelbase of the vehicle.
- Great care must be given to the positioning of the lifting ram both in terms of providing supports of adequate strength and in
order to correctly position the mountings, it is advisable to place the ram to the front of the centre of gravity of the body and
payload so as to reduce the extent of the localized load into the chassis.
- For both under floor and front end tipping gear installations it is recommended that an appropriate stabilizer is fitted to act as
a guide during the tipping operation.
- The lifting ram must be mounted on the subframe. The useful volume in the body must conform. With the maximum permissible
load on the axles. To the density of the material that is to be transported (a density mass of approx. 1600 kg/m3 is to be used
for excavated material).
When freight having a low density is transported, the useful volume may be increased within the limits established for the maxi-
mum height of the centre of gravity of the payload plus the fixtures.
- The bodybuilders must ensure the functioning and safety of all parts of the vehicle (for instance, the positioning of lights, tow
hook etc.) is safeguarded and in full compliance with the current safety regulations.
Fitting Box-bodies
Figure 3.18
123840
1. Subframe - 2. Brackets - 3. Plates - 4. Tipping hinge bracket
Fitting Box-bodies
3.4.3 Heavy-duty Service
NOTE Not applied to Stralis
3.4.4 Light-duty Service
For these operations we recommend using vehicles with short wheelbases. In Table 3.5 are listed the longitudinal runners to
be used. It is understood that the vehicle must be used for light duty on good roads, to transport freight with a low density and
a low coefficient of friction.
In addition to the above general specifications, in order to give the vehicles the required rigidity and stability, the following points
must be observed:
- Carefully check the chassis specifications (suspension, chassis, number of axles) to select a vehicle suitable for the body and its
intended operation.
- The rear end of the subframe must be stiffened using box-type sections, crossbraces, cleat plates etc.
- The rear tipping hinge must be placed as near as possible to the rear hanger bracket of the rear suspension.
- In cases of vehicles having wheelbase longer than the standard tipper wheelbase, specially stiffened rear tipping support anchoring
should be used so as to contain sag and ensure good stability during operation.
The rear tipping angle should be between 45º while the user should be informed that the tipping should be done on as flat a
surface as possible.
- Use the most rigid rear suspension available and rear anti roll bars. When parabolic rear springs are used, the stiffness should
be increased using rubber elements that operate at static load.
- For vehicles with pneumatic rear suspension, (for 6x4 tandems with four air springs for each axle), dump the air from the suspen-
sion during the tipping operation to allow the vehicle the greatest stability during tipping. It is important that this operation takes
place automatically from the tipping control. The resetting (raising) of the suspension can also be operated by the tipping control
as the body is lowered.
- On vehicles with standard third axle or added third axle (6x2), an antiroll bar may have to be fitted onto the 3rd axle depending
on the type of installed suspension to improve the transverse stability. In addition to the above instructions, hydraulic or mechan-
ical stabilisers may have to be installed for operation depending on the tipping support location in relation to the rear axles, to
suspension types and to intended operation. The third axle must never lift when tipping.
Table 3.5
Minimum subframe section
(yield limit of the material used)
M d l
Model Section modulus depending on the material yield limit (N/mm2)
240 360
AT-AD190 46
89(2)
AS/AD/AT260/TN 89/110 (1)
AS/AD/AT260/PT260Z/P 150/190 (1)
89/110 (1)
AS/AD/AT260/P(S)FP/FS 173/222 (1)
89/110 (1)
(1) Necessity for a boxed section with connections resistant to shearing, starting from approx. 1000 mm in front of the centreline of the drive axle(s) up to the
rear end of the chassis.
(2) For 8000 kg. On axle
Fitting Box-bodies
3.4.5 Containers
Not all vehicles lend themselves equally well to be used for removable type containers (i.e. the containers which can be unloaded
by sliding along the subframe). Heavy duty vehicles are certainly better suited to this use but it is best to consult IVECO concerning
the suitability of the various models in relation to the use of the vehicle. (Table 3.4)
This type of operation is subject to additional stresses compared to those of normal on-road vehicles with fixed platform bodies,
in particular as regards loading/unloading operations.
For this reason, the auxiliary frame used (see point 3.1) should be of the same dimensions as that for light tippers. (point 3.4.4)
Where vehicles with long wheelbases or rear overhangs are used, it may be necessary to use runners of larger dimensions for the
subframe.
The interchangeable body must rest on the vehicle subframe along its entire length or a least be in contact with an extensive area
of the suspension attachment points.
The lifting devices must be fixed to the subframe as indicated in point 3.6.
Vehicle stability must be guaranteed and comply with DIN standard 30722.
The stability of the vehicle must always be ensured during loading and unloading operations. We recommend fitting the rear ends
with supports (stabilisers) that are to be used during loading and unloading operations particularly when roll on, roll off containers
are used.
These supports are also recommended if the rear axles have pneumatic suspensions.
As an alternative, refer to the explanations in point 3.4.4, concerning dumping the air from the suspension during the operation.
It is very important, with this type of vehicle, to adhere to the specifications concerning the height of the centre of gravity (see point
1.13.2), when containers for high payloads are used.
Figure 3.19
123839
The distance between the last rear axle and the sliding pivot must not exceed 900 mm.
Fitting Box-bodies
Tractors for Semitrailers
3.5 Tractors for Semitrailers
For this use the vehicles provided by Iveco with specially designed equipment (chassis, suspension, brakes) should be used. The
models with pneumatic rear suspension are particularly well suited because of the constant height of the fifth wheel to transport
containers.
3.5.1 Position of the Fifth Wheel
The position of the fifth wheel may be selected from among the positions established by Iveco in relation to the kerb weight
of the tractor in its standard version. If, as a result of subsequent additions and/or modifications, the kerb weight should be changed,
reference must be made to the actual weight of the tractor and its complete equipment (supplies, driver, equipment etc.) in observ-
ance of the permissible loads on the axles when checking the position (see point 1.13.1).
To ensure a correct coupling with the semitrailer, particularly when the fifth wheel forward positions differ from the standard ones,
the geometric positioning must be carefully checked (see point 3.5.3).
3.5.2 The Fifth Wheel
All fifth wheels having load characteristics, dimensions and performance that have been declared suitable for a specific use by
their manufacturer, may be used on our vehicles. The type of fifth wheel to be selected depends on the vehicle and on the type
of transport to be carried. For instance, for off-road use, fifth wheels with an adequate degree of transverse oscillation must be used
to avoid excess stress on the vehicle’s chassis due to torsion.
Where government regulations require it, fifth wheels must meet all requirements or be homologated. Regarding their mounting,
number of bolts, dimensions, materials and positioning of longitudinal and transverse stops, see the instructions provided by the
manufacture of the fifth wheels.
As the fifth wheel is very important to vehicle safety, it must not be modified in any way.
3.5.3 Coupling of Tractor and Semitrailer
Semitrailers must not have constructive characteristics (such as excessively flexible chassis, inadequate braking power) that would
adversely affect the operation of the tractor. The coupling of the tractor and the semitrailer must take into account all their respective
movements under all operating conditions and ensure adequate safety margins which may be required by law or regulations for
road use (see Figure 3.20).

Figure 3.20
E=Front tractor clearance space - E1=Front tractor turning radius -

F=Rear tractor turning radius - F1 =Rear semitrailer clearance space
When required to do so, the required manoeuvring space in curves must be checked.
Concerning the definition of the height from the level of the 5th wheel, any limits imposed by the Manufacturer and/or government
regulations must be observed.

3.5.4 Fifth Wheel Mountings
When the tractor is delivered without the bed plate for the fifth wheel, the following instructions must be adhered to for its
construction:
- The mounting must be adequately dimensioned to handle the vertical and horizontal loads transmitted by the fifth wheel. Con-
cerning its height, bear in mind what has been said in previous points.
- Concerning the properties of the material and mounting, refer to point 3.1.1 and 3.1.2
- The upper and lower surfaces of the mounting must be even to ensure a good bearing on the chassis of the vehicle and of the
base of the fifth wheel.
- In cases where the mounting is supplied in component parts they must be assembled by welding and/or riveting.
- The fixing of the mounting to the chassis (see Figure. 3.21, 3.22 and 3.23) must be made on the angle support, if provided or
as otherwise specified.
For the fixing use flanged head bolts and nuts with a min, class of 8.8. An arragement to stop the bolts working loose must be
used. The number of bolts and diameter must be at least equal to that require to secure the fifth wheel.
When attaching logitudinal stop this must be achieved without welding or making holes in the sidemember flanges.
It is permissible to attach cad up ramps to the chassis, on marking and fitting them. The following must be considered.
- To make them of suitable size to ensure that the semitrailer can be properly engaged with the fifth wheel.
- That the fixing to the chassis must be achieved without welding or making holes in the side member flanges.
Installation of Simple Plate-type Mounting

As a general rule, for tractors that are intended for normal road use, and if not otherwise specified by Iveco, the mounting plate
for the fifth wheel must be fret-shaped (see Figure 3.21), connected to the chassis by means of longitudinal runners and appropriate
brackets.
For certain models and markets this type of installation may also be permitted not exclusively for on-road uses. In these cases, the
nature of the use and of the loads does not require direct contribution by the structure to the chassis to counteract the effects
of flexing and torsion.
The fret -shaped plate is supplied with the vehicle and provisionally fastened to it.
The final installation will be carried out by the person in charge of the installation of the fifth wheel.
The fifth wheel support plate is especially important to safety (in some countries it must be specifically certified). Assembly instruc-
tions must be strictly followed and no modification carried out.

Table 3.6 - Fifth wheels
Fifth wheel and plate application Tractors 4x2 Tractors 6x2C Tractors 6x4
Fifth wheel mounting plate 440T/P 440T/FP-LT 440TX/P 440TZ/P-HM
Fifth wheel with pin 2’’, H = 140 mm
/ S / /
integrated plate
Fifth wheel with pin 2’’, H = 150 mm - Jost
f / f f
+ plate 50 mm
Fifth wheel H = 150 mm
f / f f
+ plate 100 mm
Fifth wheel rest plate H = 150 mm
f f / /
+ plate 12 mm
Fifth wheel mtg plate H = 100 mm f / f f
Fifth wheel mtg plate H = 50 mm f / f /
f / f f
+ plate H = 12 mm
f / f f
+ plate H = 100 mm
Fifth wheel without plate - Jost H = 190 mm f / / /
Fifth wheel without plate - Jost H = 225 mm f / / /
Fifth wheel H = 148 mm
f / / /
+ plate H = 8 mm
S standard
f optional

Table 3.7 - Fifth wheel dimensions
Plate Fifth wheel Iveco / Jost fifth wheel Fifth wheel height with
height height height (without plate) integrated plate
(mm) (mm) (mm) (mm)
50 150 200
50 185 235
100 185
12 150 162 Iveco
8 148 140 Jost
Table 3.8 - Model/type application
Total fifth wheel Models Suspension Tyres Mudguard Fifth wheel plate
height setting height from the ground
(mm) (mm) Dimension C (*) (mm laden)
(mm)
200 4X2 / P 160 (S) 315 / 80 150 ∼1170
295 / 80 ∼1155
140 (O) 315 / 70 120 ∼1120
(SW 06114) 305 / 70 ∼1110
315 / 60 ∼1090
295 / 60 ∼1075
235 4X2 / P 160 (S) 315 / 80 174 ∼1205
295 / 80 ∼1190
285 4X2 / P 160 (S) 315 / 80 174 ∼1255
295 / 80 ∼1240
162 4X2 / P 140 (O) 315 / 60 120 ∼1050
(SW 06114) 295 / 60 ∼1035
305 / 70 ∼1070
315 / 70 ∼1080
140 4X2 / FP-LT 85 295 / 60 120 ∼960
315 / 60 ∼975
162 4X2 / FP 85 295 / 60 120 ∼985
(156) 315 / 60 ∼1000

Fitting instructions for 4x2 models: AS/AD/AT 440 S... T/P and T/FP
Figure 3.21
A B
Centre line
missing
A View from A B View from B
1. Fifth wheel centreline - 2. Rear wheel centreline - 3. Fifth wheel position - 4. Longitudinal runners - 5. Fifth wheel bed plate -
6. Class 10.9 M16x1.5 screws - 7. Fixing spacers (h=15mm) - 8. Self-locking flanged-head nuts - 9. Chassis side members
Bed Plate Fixing
- Having determined the fifth wheel forward position, secure the longitudinal runners to the plate using screws (6), spacers (7)
and the self-locking nuts (8).
- Tighten the nuts (8) (tightening torque 260 to 300 Nm).

Fitting instructions for models 4x2: AS/AD/ATD 440 S...T/P and T/FP
With crossbrace (Option 7727 - 7728)
Figure 3.22
1. Fifth wheel centreline - 2. Rear wheel centreline - 3. Fifth wheel position - 4. Longitudinal Runners - 6. Class 10.9 M16x1.5
screws with flange - 7. Washer (h=6mm) - 8. Self-locking flanged-head nuts - 9. Chassis side members

Fitting instructions for models 4x2: AS/AD/AT 440 S...T/P and T/FP
Without crossbrace (Option 7830)
Figure 3.23
1. Fifth wheel centreline - 2. Rear wheel centreline - 3. Fifth wheel position - 4. Longitudinal Runners - 5. Plate -
6. Class 10.9 M16x1.5 screws with flange - 7. Washer (h=6mm) - 8. Self-locking flanged-head nuts -
9. Chassis side members - 10. Fixing spacers (h=15mm)

3.5.4.1 Preparation and installations of a Structure Working together with Chassis
In addition to distributing the weight that bears on the fifth wheel the purpose of installing a suitable mounting similar in construc-
tion to the subframe shown in Figure 3.24, is to give the vehicle’s chassis added torsional and flexional strength. It is required for
extreme heavy- duty operations in certain markets for the models indicated in Table 3.9. The table also gives the minimum dimen-
sions for the longitudinal runners for the side members. For dimensions, see table 3.2 depending on modulus of resistance Wx.
These must be connected by cross members, an adequate number of which must be placed in the area where the fifth wheel is
positioned, while the remainder are distributed at the end of the straight section.
The mounting plate bearing the fifth wheel may be constructed in one of the following ways:
- by means of a plate of suitable thickness, of a length and width which is proportional to the fifth wheel supports or by means
of two plate halves of greater length;
- by means of a fret-shaped plate which the Manufacturer of the fifth wheel can supply ( height 30 or 40 mm) where there are
no problems concerning the height of the fifth wheel.
The plate(s) on which the fifth wheel is fitted must be joined rigidly to the framework of the base (side and cross members).
The supports already provided by Iveco (longitudinal and/or cross members) must be used to secure the structure to the main frame.
The best type of connection is provided by the use of plates at the rear and in proximity to the fifth wheel to stop sideways and
lengthwise movement, and brackets towards the front (see Figure 3.24). In addition to the other general type specifications given
in point 3.5.4, the specific requirements stipulated for certain models on their respective drawings (are available on request) must
also be adhered to.
Figure 3.24
Solution 1
A.R.A.
B
2 axles
2 Axles min.2100
min. 1200
3 axles
3 Axles min.1700
min. 1700
2 Axles
2 Axles min.min.
2 axles 2100
min. 800
1200
3 Axles
3 Axles min.
3 axles
min. 1000
min.
17001700
Solution 2
1. Fifth wheel pivot centreline - 2. Rear wheel or tandem centreline - 3. Fifth wheel position - 4. Standard equipment angle
piece - 14 dia. screws - 5. Front brackets - 16 dia. screws - 6. Plates - 14 dia. screws - 7. Longitudinal runner (see Table 3.5)
Av = Distance between front axle and fifth wheel centreline Lv = Minimum required reinforcement lenght when a LH =
special runner profile (see Table 3.9) is used - 8. Stiffening crossties - 9. Rear cross members (for L> 400 mm) -
10. Half-plate (min thickness = 8 mm) - 11. Plate (min. thickness = 10 mm) - 12. Fret-shaped plate - 13. Channel profile -
14. Fixing angle piece

Table 3.9 - Minimum indications of subframe profile
Minimum reinforcement profile

Section modulus based on the
Wheelbase yield point of the material
Models (mm) (N/mm2)
( )
FE240 = S235 FE360 = S355
240 360
3200 902)3) 572)5)
AS/AT/AD 1901)
≤ 3500 1502)3) 572)4)
AS/AT/AD 440 T; T/P: T/FP
≤ 3800 2082)3) 902)4)
1736) 426)
3200/1380
AS/AD/AT 260/Z/P1) 2082)3) 1502)5)
AS/AD/AT 440 T 2086) 576)
3500/1380
2082)3) 2082)5)
736)
AS /AD/AT 260/P; /PS; /FP; /FS; /FT; /FT1) 3200/1395 2086)
2082)5)
AS/AD/AT 260/P; /FP1) 576)
2800/1395 2086)
AS/AD/AT 440 TZ/P; 2082)5)
1) When converting a truck into a semitrailer tractor, the wheelbase to be used must be equal to that of standard tractors, or suitably reduced.
2) For heavy-duty use of vehicle (e.g. non-EU countries).
3) For heavy-duty use of vehicle up to 6500 kg on the front axle
6) For on-road use of vehicle and load on front axle ranging from 7500 to 8000 kg (this is obtained by means of high fifth wheel displacement values).
Should it be necessary to reduce the height of the runner profile using shear resistant connections between the chassis and the
subframe (see Table 3.9) instead of the channel profile specified in Figure 3.24, it is possible to make use of combined section runner
profiles (see table below) provided the width and thickness values are no less than the tabulated ones. These are instructions of
a general nature applying to the material covered by this manual. Materials of higher mechanical specifications call for the measure-
ment of the overall chassis and subframe bending moment. Do not use sections with a height of less than 80 mm in order to provide
the chassis with adequate stiffness characteristics.
For section dimensions see Table 3.2.

Solutions adopting combined section reinforcement profiles (see Figure 3.3)
A B CoD E F G
Material yield point ≤ 320 ≤ 320 ≤ 240 ≤ 240 ≤ 360 ≤ 360
(N/mm2)
reduction (mm)
Combined reinforcements
length
LV :
LH: 0.3AV 0.4AVV 0.5AV 0.55AV 0.5AV 0.55AV
(see Figure 3.23) 0.2AV 0.22AVV 0.25AV 0.25AV 0.25AV 0.25AVV
Example: 210X80X8 190X80X8 150x80x8 130x80x8 150x80x8 130x80x8
Combined section as an alternative to + straight + straight + angle + angle
the channel section (mm): section section section section
15x80 15x80
Actual height reduction 40 52 85 97 92 104
(mm)
The above data cannot be used when the subframe is connected to the vehicle chassis by means of brackets. In this case, moments of resistance and stress data
must be calculated for each chassis and subframe section.
3.5.4.2 Converting a Truck into a Semitrailer Tractor
In certain cases, on models where no tractor unit was originally planned, it is possible to obtain the necessary authorisation to convert
a truck into a semitrailer/tractor. The specifications relative to such a conversion in terms of fifth wheel mountings, modifications of the
chassis (i.e. suspension, braking system etc.) based on the use of the vehicle, must be defined in each case.
3.5.4.3 Variable height fifth wheel (only for Low tractor)
Iveco offers its Customers a variable height fifth wheel solution, type-approved only for Low tractor units.
It must be clarified that the above device may be used in the lower position for any type of vehicle (except quarry and building site
and tipper trucks), while in the higher position it must not be permitted under any circumstances for the following applications:
• Conversions with high centre of gravity
• silos
• Tanker trucks
• Tipper trucks
• Quarry and building site vehicles
The maximum height of the fifth wheel measured from the ground surface is also authorised up to 1200 mm in accordance with EEC
Braking certificate.

Transport of Indivisible Materials (Bascules)
3.6 Transport of Indivisible Materials (bascules)
The transport of indivisible material and of freight whose dimensions exceed normal ones, is regulated in various countries by
special legislation.
The particular configuration of these transports in which stress is created as a result of the concentrated vertical load and of the
dynamic forces that may arise when braking, requires that the choice of vehicle to be used is checked with Iveco beforehand.
The structure that bears the weight on the tractor must use a subframe (see point 3.5.4.1): other conditions that must be met for
this type of transport will be specified each time in our authorisations.
Transport of Indivisible Materials (Bascules)

Installation of Tanks and Containers for Bulk Materials
3.7 Installation of Tanks and Containers for Bulk Materials
a) Installation through application of a subframe

As a general rule, the installation of tanks and containers on our vehicles requires the use of an appropriate subframe.
Table 3.10 contains the recommendations for the dimensions of the longitudinal runners to be used for the subframe.
Table 3.10 - Installation of tanks
Minimum reinforcement profile

Models Section modulus Wx (cm3)
(Yield limit of material used=360N/mm2)
461)
AS/AD/AT 190
892)
591)
AS/AD/AT 260
892)
(1) Stiffen the subframe in the area on which the tanks and containers rest;
(2) Locate the front tank support in front or near to the rear support of the spring on the 2nd front axle, otherwise the use of a larger section and specific authorisa-
tion will be necessary.
Tankers, or more generally, structures which are torsionally very rigid, must be fitted so that the vehicle chassis retains sufficient
and gradual torsional flexibility, by avoiding areas of high stress.
When installing a tank we recommend using elastic joints (see Figure 3.25) between the body of the tank and the subframe in front
and rigid supports that are capable of withstanding longitudinal and transverse forces at the rear.
Figure 3.25
As mentioned in the case of other applications, the positioning of the mountings through which the forces are discharged is similar
here. Rigid mounts are position corresponding to the rear suspension supports and the flexible mounts as near as possible to the
rear support of the front suspension.
When faced with a different situation, a possible solution could be that of reinforcing the structure by means of longitudinal runner
profiles of larger dimensions in comparison with those given in Table 3.10.

The rigidity characteristics of the vehicle chassis as well as the area where the connections are to be installed and the type of use
for which it is intended must be taken into account.
As a rule, for road use, it can be said that the first front elastic connection will allow for a gap of approximately 10 mm between
the subframe and frame during the chassis torsional stage.
In order to define the elastic connection.
b) Installation without application of a subframe
Tanks may be mounted directly onto the vehicle chassis without fitting an subframe under the following conditions:
- the distance between saddles must be determined depending on the load to be carried and must not exceed 1 meter.
- saddles must be fitted so as to allow an even distribution of the loads over a considerably large surface. Suitable brackets must
be provided between the saddles to limit the longitudinal and transverse thrusts.
- other anchoring solutions may be authorised by Iveco.
- self-bearing tanks may be positioned directly on the chassis by means of suitable mountings located right behind the cab and
in the area of the rear axle(s). The number and distribution depends on the number of axles and the wheelbase; this may vary
from min. 2 for each side on 2- axle vehicles with short wheelbases to min. 3 for 3/4-axle vehicles with short wheelbases (see
Figure 3.26).
- the mountings must be sufficiently long (600 mm approx) and be positioned next to the suspension mountings (max. distance
400 mm).
- to permit the necessary torsional movements of the chassis, elastic front mounting should be used where possible.
Other solutions are possible depending on the type of construction.

Figure 3.26
The installation of two or more separate containers or tanks on the vehicle requires the use of subframe that permits good distribu-
tion of the load and an adequate torsional rigidity for the chassis/subframe using connections resistant to shearing. A good solution
is constituted by using a rigid connection which connects the containers together.
In order to adhere to the maximum admissible load limits on the axles, it is necessary to establish the maximum volume, the degree
of filling of the container and the density of the freight. When separate tanks or individual containers with separate compartments
are used, care must be taken to ensure that with every degree of filling the maximum permissible load on the axles is respected
as well as the minimum ratio between the load on the front axle and fully loaded vehicle weight (see point 1.13.2).
In consideration of the nature of this equipment, special attention must be paid to limiting the height of the centre of gravity as much
as possible to ensure good handling (see point point 1.13.2); we recommend the use of vehicles with stabiliser bars.
It is necessary to provide special transverse and longitudinal bulkheads inside the tanks and containers for liquids in order to reduce
the dynamic loads which the liquid transmits when the vehicle is in motion and the tanks are not filled to capacity which would
adversely affect the handling and resistance of the vehicle.
The same holds true for trailers and semitrailers, in order to avoid dynamic loading on the coupling devices.
Concerning the installation of containers for fuel or flammable liquids, all current government safety regulations must be abided by
(see point 2.18).

Installing a crane
3.8 Installing a crane
The selection of the crane must be made with due consideration to its characteristics (weight, maximum torque) in relation to
the performance of the vehicle.
The positioning of the crane and of the payload must be done within the load limits permitted for the vehicle. Installation of the
crane must be carried out in compliance with statutory requirements, national standards (e.g. CUNA, DIN) and international stan-
dards (e.g. ISO, CEN), depending on which of these is pertinent to the particular vehicle.
While the crane is operating, the stabilisers (hydraulic if possible) must be used and be in contact with the ground. As a general rule,
the installation of a crane requires the use of a suitable subframe, whose construction must taken into account all general specifica-
tions relating to it (point 3.1). Concerning the dimensions of the runners for the subframe, refer to Tables 3.12, 3.13 and 3.14.
In those cases where no specific subframe is called for (areas indicated with an ”A”) it is still necessary to provide a suitable mounting
on the chassis for the crane using the standard body subframe (the length of the section members must be at least 2.5 times the
width of the base structure of the crane) in order to distribute the load and the stress developed during the operation of the crane.
If the vehicle requires the use of its own subframe, it may also be used for the crane provided that its dimensions are adequate.
Special cases, whose Mg value fall within the areas designated with the letter ”E” (or for higher values) must be checked individually
each time.
Figure 3.27
MG max = (F · L + P · l) max
The dimensions of the subframe refer to the total maximum static moment of the crane (MG max.) which is calculated on the
basis of the equation given in Figure 3.27.
The decision concerning the number of stabilisers and the type of subframe to be used, particularly in terms of torsional rigidity (box-
type sections, cross members etc.) is determined by the maximum moment of the crane and its position for which the Manufacturer
of the crane and installer are responsible.
The verification of the stability of the vehicle when the crane is operating must be done in compliance with the applicable government
regulations.
Installing a crane
3.8.1 Crane Behind the Driver’s Cab
The mounting of the subframe onto the chassis will as a rule, be made using the standard brackets (see Figure 3.28) to which
are added, if necessary, other flexible anchorages (brackets or clamps) so that the flexibility and torsional characteristics of the chassis
remain unchanged.
The dimensions and the subframe to be used for this type of installation are specified in Table 3.9.
For on-road vehicles only if the height of the subframe runner profile has to be reduced (e.g. to lower the total height of the vehicle)
the mounting of the subframe may be carried out with shear resisting connections (see Figure 3.29). For these applications, the
minimum dimensions of the reinforcing runner are specified in Table 3.10. In all case the maximun rear wheel travel / movement
must be allowed.
The use of runners with a constant cross-section is recommended over the entire useful length of the vehicle. Any possible gradual
reduction of the cross-section of the runners is permissible in those areas in which the flexional moment induced by the crane as-
sumes values that correspond for those of boxes marked ”A”in Tables 3.12. and 3.13.
The subframe for the crane may be integrated with the body longitudinal runner as shown in Figure 3.28 Length ”Lv” must not be
less than 35% of the wheelbase for vehicles with forward-control cab when the body runner has a smaller cross-section.
Figure 3.28
1. Subframe - 2. Connections - 3. Crane joints - 4. Stabilisers
Installing a crane
Table 3.11 - Cranes mounted behind the driver’s cab (subframe mounted with brackets or clamps)
Models Wheelbase (mm) Crane capacity MG max (kNm)
Yield 20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280
point of - - - - - - - - - - - - - - - - - -
subframe
bf
20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280 300
(Chassis frame material
section in mm) (N/mm2) Minimum value of subframe Section Modulus Wx (cm3)
AS 190 240 A A A A A A A A A A 211) 89 343 439 E E E E E

AS 260 360 A A A A A A A A A A 211) 89 119 150 245 374 439 E E
(289X80X6,7) 420 A A A A A A A A A 211) 89 119 150 185 208 245 343 406
AS 260 Y/P 5700/1395 240 A A A A A A A A A A A 211) 89 406 E E E E E
AS 260 Z/P 6050/1395 360 A A A A A A A A A A A 211) 89 119 150 245 374 474 E
(289X80X7,7) 420 A A A A A A A A A A A 211) 89 119 150 185 208 245 343
A = The reinforcing profile prescribed for the respective superstructure is sufficient (e.g. for normal bodies). Close the reinforcing profile in the crane mounting
area. In the crane area, reinforcing profiles with thickness of less than 5 mm must be reinforced.
E = To be checked on a case-by-case basis. Send the technical documentation with the checks of stresses and stability to the appropriate IVECO bodies.
(1) When the auxiliary frame requires a high moment of resistance (e.g to install platforms) the latter shall be established also for the crane.
Figure 3.29
When installing cranes on large-cab vehicles, should it be impossible to extend the subframe up to the rear support of the front
spring, it may be necessary to contain crane rotation according to crane capacity, so as not to exceed bending moment allowance
for the chassis.
Installing a crane
Installation of cranes on off-road vehicles may require fitting elastic mountings between the chassis frame and subframe on the front
and central areas (see Figure 3.11) so as not to excessively constrain the chassis torsional movement. Since in such cases the crane
will be virtually connected to the subframe only, the size of the longitudinal runners must be adequate to resist the crane operation-
generated movements.
The functioning of the equipment that is placed behind the cab (e.g. gear levers, air filter, locking device for the tilting cab etc.) must
not be impaired. Relocating assemblies such as batteries box or fuel tank is permissible provided that the original type of connections
are re-established.
Normally, when the crane is placed behind the cab, it is necessary to move the body or equipment towards the rear. In the specific
case of tipping equipment, particular care must be given to the placement of the lifting device and of the rear tipping hinges which
should be moved back as little as possible.
Table 3.12 - Cranes mounted behind cab (subframe fixing with shear-resistant plates)
Yield 20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280
point of
subframe
sub a e - - - - - - - - - - - - - - - - - -
material
i l
20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280 300
(N/mm2)
(Chassis
(Ch i frame
f
section in mm) Minimum value of subframe Section Modulus Wx (cm3)1)
AS 190 up to 6300 240 A A A A A A A A 311) 46 89 105 150 173 245 E

AS 260 up to 5100/1395 360 A A A A A A A A A A 311) 46 89 89 135 150 173 208 245
(289X80X6,7) 420 A A A A A A A A A A A 31 361) 89 89 105 135 150 173
AS 260 Y/P 5700/1395 240 A A A A A A A A A 311) 361) 89 89 135 150 208 245 E
AS 260 Z/P 6050/1395 360 A A A A A A A A A A A 311) 361) 89 89 105 135 150 173
(289X80X7,7) 420 A A A A A A A A A A A A A 311) 46 89 89 105 135
240 63 94 125 157 188 219 250 282 313 375 438 500 563 625 688 750 813 875 938
Section modulus Wx (cm3) 360 48 72 96 120 143 167 191 215 238 286 334 381 329 477 524 572 169 667 715
required for the chassis +
420 40 60 80 100 120 140 160 180 200 240 280 320 360 400 440 480 520 560 600
subframe aggregate section
490
} *
34 50 67 84 100 117 134 150 167 200 234 267 300 334 367 400 434 467 500
* Also valid for chassis runner profile (lower flange of the aggregate section).
A = The reinforcing runner required for the corresponding subframe is sufficient (e.g. Table 3.4 for standard platform bodies).
The reinforcing runner in the crane’s mounting area is to be closed. In the same area, the reinforcing runners with thickness less than 5 mm are to be reinforced.
E = To be checked for case to case (submit the technical documentation with the calculation made to determine stress and stability).
(1) When the auxiliary frame requires a high moment of resistance (e.g to install platforms as per Table 3.1) the latter must be established also for the crane.
2) The application of these capacity ranges of the cranes requires that the vehicle’s stability be carefully verified (possibility of using stabilisers with a greater
extension or resorting to heavier ballast).
3) Should one wish to reduce the height of the runner profile using shear resistant connections between the chassis and subframe instead of the specified channel
section (moment of resistance as per Table 3.12) it is possible to make use of combined section runner profiles (see table below) provided that the flange
width and thickness values are no less than the tabulated ones. These are instructions of a general nature appl ying to materials covered by this manual. Material
with higher mechanical specifications call for the measurement of the overall chassis and subframe bending moment (see last part of Table 3.13). However
it should be remembered that for the part of the runner profile which is not reinforced (channel section) the moment of resistance must not be less than
the one required for the subframe concerned (i.e. Table 3.4 for fixed platform bodies).
As a reduction of the subframe runner entails a reduction in the subframe moment of resistance, the Bodybuilder who is envisaging the installation of a crane
with 4 stabilisers will have to work out the means for ensuring adequate torsional stiffness for the af in the crane resting area. For this reason we recommend
that the height of the runner profiles be not less than 120 mm. However, as this solution also implies a restriction of the torsional capacity of the main chassis
while the vehicle is travelling, we recommend that its use be confined to on-road use
Installing a crane
Installing a crane
Table 3.13 - Solutions with combined section runner profiles (see Figure 3.5)
A B CoD E F G
Material yield point ≤ 320 ≤ 320 ≤ 240 ≤ 240 ≤ 360 ≤ 360
(N/mm2):
reduction (mm):
Combined reinforcements
length LA 0.35Lh LA 0.45Lh LA 0.55Lh LA 0.6Lh or.
(see Figure 3.26) LV= 0.25Lh or or LA 0.4Lh or or or LA
Example: 210x80x8 90x80x8 150x80x8 130x80x8 150x80x8 130x80x8
Combined section as an alternative + straight + straight + angle + angle
to the channel section (mm): section section section section
C250x80x8 mm: 15x80 15x80
Actual height 40 52 85 97 92 104
reduction (mm)
The above data cannot be used when the subframe is connected to the vehicle chassis by means of brackets (see Table 3.11). In this case, moments of resistance
and stress data must be calculated for each chassis and subframe section.
3.8.2 Crane on Rear Overhang
It is advisable for this type of application, to extend the subframe over the entire length of the vehicle that is available for the
body up to the back of the cab or if this is no possible the rear support of the front spring. The dimensions of the runners to be
used are given in Table 3.14.
In consideration of the particular distribution of the load on the vehicle, where the load is concentrated on the rear overhang, in
order to ensure the rigidity that is necessary for good performance on the road and when the crane is in operation, the subframe
must be strengthened and stiffened in relation to the capacity of the crane. Box-type sections (see point 3.2) and brackets are to
be used in the area of the rear suspension and the rear overhang (Length Lv as per Figure 3.30). Care must also be taken to ensure
that the transition from box-type to open section is well blended as illustrated in Figure 3.5 and 3.6.
In the area that is affected by the box-type section, the frame must be secured to the chassis of the vehicle by means of shear-resistant
plates (i.e. an adequate number of plates spaced at most 700 mm from each other), whereas elastic mountings are to be used in
the front part. Due care must be taken to ensure that under any load conditions, the ratio of the weight on the front axle to the
rear axle or axles, respects the limits set for the vehicle (see point 1.13.3).
As the required stiffness of the subframe depends on various factors (i.e. crane capacity, size of its supporting base, vehicle kerb
weight, chassis overhang) we cannot give information valid for all possible conditions. For this reason the bodybuilder will have to
assess the vehicle stability also by means of practical tests. If, as a consequence of such tests , the subframe stiffness proves insufficient,
the bodybuilder will have to achieve this objective by means of alternative methods.
The rear overhang of the crane (length Lu, see Figure 3.30) must be limited as much as possible in order to preserve the good driving
characteristics of the vehicle and acceptable stress conditions. This value must not exceed 50% of the wheelbase.
In the case of vehicles with a lifting rear axle, the verification of the minimum load on the front axle must be done with the rear
axle in the raised position in those countries which permit driving under those conditions (see point 1.13.3). If the minimum pre-
scribed value is not reached, the vehicle must be allowed to drive only with the axle in the lowered position.
Installing a crane
Figure 3.30
Lv
1. Subframe - 2. Plates - 3. Brackets - 4. Crane joints - 5. Stabilisers - 6. Connecting angle bar
Table 3.14 - Cranes mounted on rear overhang (subframe mounting with shear resistant plates)

Yield 20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280
point of
subframe
sub a e - - - - - - - - - - - - - - - - - -
material
i l
20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 240 260 280 300
(N/mm2)
(Chassis
(Ch i frame
f
section in mm) Minimum value of subframe Section Modulus Wx (cm3)1)
AS 190/P up to 6300 240 A A A A A 231) 321) 421) 57 110 135 173 222 246 E
AS 260/P; /PS; up to 5100/1395 360 A A A A A A A 231) 321) 421) 71 110 135 173 222 222 246 E
/FP; /FS up to 5100/1395 420 A A A A A A A 231) 231) 321) 421) 71 110 135 173 173 222 246 E
AS 260/PT up to 5100/1395
(289x80x6,7) up to 5100/1395
AS 260 Y/P 5700/1395 240 A A A A A A A A A A 42 71 110 135 173 222 222 E
AS 260 Z/P up to 5700/1380 360 A A A A A A A A A A 23 32 42 57 110 110 135 135 173
up to 6050/1395 420 A A A A A A A A A A 23 23 23 42 57 71 110 135 173
(289X80X7,7) up to 6050/1380
240 63 94 125 157 188 219 250 282 313 375 438 500 563 625 688 750 813 875 938
Section modulus Wx (cm3) required 360 48 72 96 120 143 167 191 215 238 286 334 381 329 477 524 572 169 667 715
for the chassis + subframe combined
section 420
490 } *
40
34
60
50
80
67
100
84
120
100
140
117
160
134
180
150
200
167
240
200
280
234
320
267
360
300
400
334
440
367
480
400
520
434
560
467
600
500
* Also valid for chassis runner profile (lower flange of the combined section).
The reinforcing runner in the crane’s mounting area is to be closed. In the same area, the reinforcing runners with thickness less than 5 mm are to be reinforced.
I = When the auxiliary frame requires a high moment of resistance (e.g to install platforms as per Table 3.1) the latter shall be used also for the crane.
2 = Should one wish to reduce the height of the runner profile using shear resistant connections between the chassis and subframe instead of the specified channel
section (moment of resistance as per Table 3.14) it is possible to make use of combined section runner profiles (see table below) provided the flange width
and thickness values are no less than the tabulated ones. These are instructions of a general nature applying to materials covered by this manual. Material with
higher mechanical specifications call for the measurement of the overall chassis and subframe bending moment (see last part of Table 3.14). However it should
be remembered that for the part of the runner profile which is not reinforced (channel section) the moment of resistance must not be less than the one
required for the subframe concerned (i.e. Table 3.1 for fixed platform bodies). As a reduction of the subframe runner entails a reduction in the subframe
moment of resistance, we recommend that the height of the runner profiles be no less than 120 mm.
Installing a crane
Table 3.15 - Solutions with combined section runner profiles (see Figure 3.4)
B D G
Material yield point (N/mm2) 320 240 ≤ 360
Max. runner profile height reduction (mm): 20 60 80
Combined reinforcements length (see Figure 3.31) LV = - 0.45 LG 0.65 LG
Example: 200x80x8 160x80x8 140x80x8
Combined section as an alternative to the channel + straight + angle
section (mm) : 220 x 80 x 8 mm section section
15x80
Actual height reduction (mm) 12 45 64
The continuity of combined reinforcement runners can be interrupted only in special cases and is subject to authorisation. Similarly, when it is difficult to apply
an external reinforcing L section (items F and G Figure 3.4) - owing to the presence of suspension mountings or air spring connection brackets - and recessing
to be performed could excessively reduce the section’s resisting capacity, the adopted solution will need special authorisation.
3.8.3 Removable Cranes
The installation of removable cranes on the rear overhang may be carried out according to the specifications of the preceding
paragraph provided the type of fixing used between the crane and the subframe does not cause additional stress to the vehicle’s
chassis.
In consideration that the vehicle may be used with or without the crane, we recommend marking on the body the position of the
useful load consistent for the two types of operating condition.
If the vehicle retains its ability to tow a trailer, all regulation concerning the proper coupling of the vehicle must be observed.
Installing a crane
Installation of Tail Lifts
3.9 Installation of Tail Lifts
The dimensions of the longitudinal runners to be used when installing tail lifts can be assessed as follows:
- By means of Table 3.16, with the standard rear overhangs and mean bending moments induced by tail lifts; as a function of their
capacity. In the table, the minimum capacity values are specified above which suitable stabilisers must be used.
- When cantilever tail lifts or with different lengths of the rear overhang and with special tail lifts (e.g. aluminium), the flexural moments
induced on the chassis frame can be determined by means of Figure 3.31, whereas the characteristics of the longitudinal runners can
be defined using the relevant figure.
The bodybuilder or the Manufacturer of the tail lift must take care to ascertain safety and operational stability, in particular when
applying Table 3.17.
In any event, particularly in those specific uses where there is not a suitable subframe (as in the case with box- type bodies built
by means of cross members), the fixing for the tail lift must be provided by a structure that enables
The stress to be distributed over the chassis of the vehicle.
Fixing with Shear Resisting Plates (ALL TAIL LIFT INSTALLATIONS)
To provide the necessary strength and rigidity at the rear of the chassis, the connection between the chassis and the subframe must
(especially in overhangs of over 1500 mm) be made using shear resisting plates. These must be fitted in the area of the overhang
and of the rear suspension and spaced not more than 700 mm from one another as shown in Figure 3.31.
Procedure for calculating the frame bending moment during loading of a tail lift.
Figure 3.31
Stabilizers
WI
Combined section Wtl
solution
(see Figure 3.5)
Rear axle(s) centreline
91538
WTL = weight of tail lift

WL = tail lift capacity
The bending moment of the frame can be calculated using the following formula:
For tail lifts without stabilisers M [Nm] = WL x A + WTL x B
For tail lifts with stabilisers M [Nm] = WL x C + WTL x D
NOTE C, D, WTL, WL : According to tail lift manufacturer’s data.

The bodybuilder must consider each time the necessity of using stabilisers even in those cases where merely in terms of stress
of the chassis their use may not appear to be necessary. When evaluating the need for stabilisers in relation to the capacity of the
platform, the stability and attitude of the vehicle resulting from the deflection of the suspension during loading operations must also
be considered.
The stabilisers, that must be attached to the platform’s supporting structure, should preferably be hydraulically operated and must
be employed during all loading procedures with the platform.
The stability of the vehicle must be verified in observance of government regulations in all operating phases of the platform.
To compensate for the elastic give of the chassis, which is inevitable when the tail lift is in operation, the bodybuilder may make
use of reinforcement runner profiles of larger size in comparison to the one indicated in Table 3.16 and 3.17.
The runner profile dimensions given in Table 3.16 apply to the rear overhangs shown. Should the latter be of larger size, it may be
necessary to consider the possibility of either installing stabilisers or larger runner profiles (see Table 3.17).
The installation of tail lifts must be carried out with due regard for the maximum permissible weights on the rear axle or axles and
of the minimum load established for the front axle (see point 1.13.3); if this should not be the case, the rear overhang will have to
be reduced.
When electro-hydraulic tail lifts are installed, it is necessary to check that the capacity of the batteries and of the alternator is adequate
(see point 5.5).
Vehicles with liftable third axles, the use of a tail lift when the third axle is lifted is only allowed using stabilisers.
The bodybuilder will be responsible for any modification to the rear underrun guard or for installing a different type (see point 2.20)
for preserving the visibility of the rear lights, for the overhang angles, and for the positioning of the tow hook as provided by the
respective national requirements.

Table 3.16 - Installation of tail lifts

Models Tail lift capacity kN (kg)
Wheelb Max. body 7.5 10 12.5 15 17.5 20 25 30

overhang (750) (1000) (1250) (1500) (1750) (2000) (2500) (3000)
ase (mm)
Minimum value of subframe Section Modulus Wx (cm3) as a function of
the yield point of the material (N/mm2)
(Chassis frame
section in mm) (mm) 240 360 240 360 240 360 240 360 240 360 240 360 240 360 240 360
AS 190/P 3800 1847 2275 A A A A A A A A 57 A 89 46 89 46 135 89
4200 2072 2500 A A A A A A 57 A 89 46 105 57 135 89 150 89
AS/AD/AT 260/P; /PS; 3800 - 2207 89 46 89 46 89 46 135 89 135 89 135 89 150 119 208 135
/PT 4200 - 2567 89 46 105 57 135 89 150 89 150 89 173 105 208 135 286 150
(302,4/212,4x80x6,7) 4500 - 2522 89 46 105 57 135 89 150 89 150 89 173 105 208 135 286 150
4800 - 2522 89 46 105 57 135 89 150 89 150 89 173 105 208 135 286 150
5100 - 2252 89 46 89 46 89 46 135 89 135 89 135 89 150 119 208 135
AS/AD/AT 260/TN bis 5700 - 3475 A A A A A A A A A A A A A A A A
AS/AD/AT 260/PT bis 5100
(P. 5700/1380)
(302,4x80x6,7)
4471 1307 1760 A A A A A A A A A A A A A A 89 46
4471 1802 2250 A A A A A A A A 57 A 89 46 89 46 135 89
AS/AD/AT 260/P; /FP; 5101 1577 2030 A A A A A A A A A A A A 89 46 89 46
(302,4/212,4x80x6,7) 5101 1982 2430 A A A A A A 57 A 89 46 89 46 105 57 135 89
5101 2207 2660 A A A A 57 A 89 46 89 46 89 46 135 89 150 89
5101 2387 2840 A A 57 A 89 46 89 46 105 57 135 89 150 89 173 105
5686 1982 2430 A A A A A A 57 A 89 46 89 46 105 57 135 89
5686 2207 2660 A A A A 57 A 89 46 89 46 105 57 135 89 150 89
6271 2027 2480 A A A A A A 571) A 89 461) 89 461) 135 89 150 89
6271 2387 2840 A A 571) A 89 461) 89 461) 105 571) 135 89 150 89 208 105
6271 2792 3240 89 461) 89 461) 105 571) 135 89 135 89 150 89 208 135 245 150
AS/AD/AT 260/P; /FP; 4201 1127 1580 A A A A A A 46 A 89 46 89 46 105 57 135 89
/FS; /PS 4201 1622 2070 57 A 89 46 89 46 89 46 105 89 135 89 150 89 208 135
(302,4/212,4x80x6,7) 4471 1217 1670 A A A A A A 57 A 89 46 89 46 105 57 135 89
4471 1622 2070 57 A 89 46 89 46 89 46 105 89 135 89 150 89 208 135
4786 1487 1940 A A 57 A 89 46 89 46 89 46 105 89 150 89 173 105
4786 1712 2160 89 46 89 46 89 46 105 57 135 89 135 89 173 105 208 135
4786 2072 2520 89 46 105 57 135 89 150 89 150 89 173 105 207 135 286 150
5101 1802 2250 89 46 89 46 105 57 135 89 135 89 150 89 173 105 208 135
5686 - 2432 A A A A A A A A 46 A 46 A 46 46 46 46
AS/AD/AT 260/P; /FP 6050 2660 A A A A 46 A 46 A 46 A 46 A 46 46 73 46
(304,4 X 80 X 7,7)
3796 1127 1580 A A A A A A A A A A A A A A A A
AS/AD/AT 4201 1127 1580 A A A A A A A A A A A A A A A A
260 Z/P-HM 4201 1487 1940 A A A A A A A A A A A A A A A A
4201 1847 2300 A A A A A A A A A A A A 46 A 89 A
4471 1982 2430 A A A A A A A A A A A A 89 A 89 46
(304,4 x 80 x 7,7)
For the tail lifts with capacity up to 5 kN (500 kg) the reinforcing runner profile provided for the corresponding subframe is sufficient (e.g. Table 3.4 for standard
platform bodies).
For modes AS 190 S../P with 2792 mm rear overhang and models AS 260 S../P with 1802 and 2072 mm rear overhang, with 5 kN (500kg) tail lifts use the reinforcing
runner profiles provided for the corresponding subframe (e.g. Table 3.4 for standard bodies).

Table 3.17 - Installation of tail lifts

Bending moment permitted for runner of chassis frame/subframe
Models Moment of resistance Wx (cm3) of subframe runner 2)
Subframe 16 19 21 26 31 36 46 57 89 105 119

Wheelbase material
(mm) yield point Static bending moment permitted or chassis frame/subframe runner
Chassis frame (N/mm2) (shear resistant connections) (kNm)
section (mm)
(212.4x80x6.7 rear) up to 6300 240 55.2 61.3 65.6 63.3 67.6 74.7 78.4 82.7 (102.6) (109.2) (110.7)
up to 5100/1395 360 72.5 80.5 86.1 83.1 88.7 (98.1) (102.8) (108.6) (134.7) (143.4) (145.2)
420 86.3 (95.9) (102.5) (99.0) (105.6) (116.8) (122.4) (129.2) (160.3) (170.7) (172.9)
AS/AD/AT 260 up to 5700/1395 240
up to 6050/1395 360
(289x80x6.7) 420
AS/AD/AT 260 (6X4) up to 4500/1395 240 90.7 99.6 (105.7) (101.4) (107.5) (117.8) (121.5) (125.9) (151.7) (158.0) (157.8)
360 (119.0) (130.7) (138.7) (133.1) (141.0) (154.6) (159.4) (163.3) (199.1) (208.2) (207.1)
420 (141.7) (155.6) (165.1) (158.5) (167.9) (184,1) (189.8) (196.8) (237.0) (247.8) (246.5)
(289x80x7.7)
Models Moment of resistance Wx (cm3) of subframe runner 2)
Subframe 135 150 173 208 245 286 317 343 374 406 439 474
material yield
point Static bending moment permitted or chassis frame/subframe runner
Chassis frame Wheelbase (N/mm2) (shear resistant connections) (kNm)
section (mm) (mm)
AS/AD/AT 190 up to 6300 240 (122.8) (134.1) (143.1) (157.7) (173.0) (189.7) (201.6) (213.9) (226.8) (240.1) (253.9) (268.1)
AS/AD/AT 260 360 (161.2) (176.0) (187.7) (207.0) (227.1) (249.0) (264.6) (280.0) (297.7) (315.2) (333.2) (351.9)
up to 5100/1395
(199x80x6,7 rear) 420 (191.9) (209.6) (223.6) (246.4) (270.3) (296.5) (315.0) (334.3) (354.4) (375.2) (396.7) (418.9)
AS/AD/AT 260 up to 5700/1395 240

360
up to 6050/1395
(289x80x6.7) 420
AS/AD/AT 260 (6x4) up to 4500/1395 240 (174.3) (189.9) (199.3) (214.5) (233.3) (250.5) (262.8) (275.7) (289.0) (302.9) (317.2) (332.1)
360 (228.8) (249.2) (216.6) (281.6) (306.2) (328.9) (345.0) (361.8) (379.3) (397.5) (416.4) (435.9)
420 (272.4) (296.7) (311.4) (335.2) (364.5) (391.5) (410.7) (430.8) (451.6) (473.3) (495.7) (518.9)
(289x80x7.7)
( ) The necessity of installing stabilisers and checking stability during operation is to be ascertained.
S = Stabilisers must be installed
C = Normal (short) cab
L = Long cab
I = If the type of subframe requires it, use larger runner profiles (see Table 3.4)
2 = Should one wish to reduce the height of the runner profile using shear resistant connections between the chassis and subframe instead of the specified channel
section (Section Modulus as per Table 3.16) it is possible to make use of combined section runner profiles (see table below) provided the flange width and
thickness values are no less than the tabulated ones. These are instructions of a general nature applying to materials covered by this manual. Material with
higher mechanical specifications call for the measurement of the overall chassis and subframe bending moment. However it should be remembered that for
the part of the runner profile which is not reinforced (channel section) the moment of resistance must not be less than the one required for the subframe
concerned (i.e. Table 3.4 for fixed platform bodies). In all case the maximum rear wheel travel / movement must be allowed.


STRALIS AS/AT/AD Euro 4/5 POWER TAKE-OFFS 4-1
Index
SECTION 4
Power take-offs
Page
4.1 General Specifications 4-3
4.2 Power Take-off from Gearbox 4-5
4.3 Power Take-off from Transfer Box 4-8
4.4 Power Take-off from Drive line 4-8
4.5 Power Take-off from Engine 4-9
4.5.1 Torque power take off from the front of the engine 4-9
4.5.2 Power take off from the rear of the engine 4-10
4.5.2.1 Multipower power take-off on flywheel side 4-10
4.5.2.2 Power take-off from the timing gears at rear of engine 4-12
4.6 PTO management 4-16
4.6.1 General specifications 4-16
4.6.1.1 Definitions 4-16
4.6.1.2 Diagram functions 4-17
4.6.1.3 PTO switch 4-18
4.6.2 PTO modes 4-19
4.6.2.1 EM - PTO 1, 2, 3 configurable 4-19
4.6.2.2 EM - PTO 1, 2, 3 Programming 4-20
4.6.3 RPM Mode (to be set in the VCM control unit) 4-23
4.6.3.1 RPM 0 mode (driving mode) 4-24
4.6.3.2 Configurable rpm mode 1, 2, 3 4-24
4.6.3.3 Custom settings 4-26
4.6.3.4 Setting for special functions 4-27
4.6.3.5 Footnotes on 4.6.3.2/4.6.3.3/4.6.3.4 4-27
4.6.3.6 Changes to the torque curve, final rotation speed and steepness of the final limiter 4-29
Index
4-2 POWER TAKE-OFFS STRALIS AS/AT/AD Euro 4/5
Page
4.7 PTO management 4-31
4.7.1 No PTO installed or provisions for PTO 4-31
4.7.2 PTO Multipower 4-31
4.7.3 PTO manual gearbox with electric engagement 4-32
4.7.4 Allison gearbox PTO 4-32
4.7.5 PTO FOCSA 4-33
4.7.6 PTO engine 4-33
4.7.7 PTO Eurotronic 2 transmission 4-34
4.8 EM (Expansion Module) 4-35
4.8.1 Connections 4-36
Index
44444.
General Specifications
4.1 General Specifications
Different types of power takeoffs can be used dependine on the type of use and the performances required, the PTO (Power
Take OFF) can be fitted to:
- the gearbox;
- driveline;
- the front of the engine;
- the rear of the engine.
The characteristics and performances are given in the paragraphs which follow and in the relevant documentation which will be
supplied upon request.
For the definition of the power necessary for the apparatus to be controlled, particularly when the values requested are high, the
absorbed power should also be considered during the drive transmission phase (5 to 10% for the mechanical transmissions, belts
and gears, and greater values for the hydraulic controls).
The choice of transmission ratio for the power take-off should be made so that the absorption of power occurs in a flexible engine
operating range. Low r.p.m. (below 1000 r .p.m.) must be avoided to prevent irregular running.
The power taken in relation to the number of revolutions of the power take-off at the required torque.
M ⋅ n M ⋅ n
P(hp) = P(kW) =
7023 9550
P = Useable power
M = Torque permitted for the power take-off (Nm)
n = power take-off r.p.m.
Type of use
Both occasional and continuous use should be considered.
For occasional use periods of under 30 minutes are considered.
The values for continuous use are those used for long periods. Whenever this is comparable to that of a stationary engine, the suitabil-
ity of reducing the scheduled values on the basis of the conditions of use (engine cooling, gearbox etc.) should be evaluated.
The scheduled take-off values are also applicable for uses which do not involve large variations of torque either in frequency or
magnitude.
To avoid overloading, in some cases (e.g. hydraulic pumps, compressors) it may be necessary to include the application of devices
like clutches or safety valves.
PTO transmissions
The kinematic forces of the transmission from the power take-off to the relevant apparatus should be carefully considered (angles,
r.p.m., moment) during the design phase and the dynamic behaviour during operation in compliance with the transmission Manufac-
turer’s instructions should be respected. The dimensions should take into consideration the forces which might occur under maxi-
mum power and torque conditions.
To obtain a uniformity of kinetic forces angles of equal value, maximum of 7º, should be obtained at the extremities (Figure 4.1).
Solution Z is preferred to solution W due to the lower loads on the bearings of the power take-off and the equipment being driven.
When it is necessary to obtain different spatial inclinations (ϕ), the variations in r.p.m. should be compensated for with the arrange-
ment of the forks shown in Figure 4.2.
For transmissions employing multiple sections, the instructions given at point 2.8.2 should be followed.
Figure 4.1
Solution Z
Solution W
91522
Figure 4.2
91523
Electrical system
The VCM and EM electrical/electronic system makes available innovative methods and processes for control of power take-offs
that can significantly improve safety and reliability. Activation takes place by connecting the power take-off control switch to con-
nector ST14A.
This connector is fitted as standard if the customer has chosen a power take-off as standard. If a later power take-off is installed,
please observe the instructions given in Chapter 4.6.
Pneumatic system
See description in Paragraph 2.15.4.
Power Take---off from Gearbox
4.2 Power Take-off from Gearbox
Depending on the type of gearbox power can be taken from the layshaft through the flange or spline located on the rear, side
or lower part of the gearbox.
The technical characteristics necessary are given in the documentation supplied upon request for the various gearboxes.
The types of power take-off and the torque values obtained with the ratio between the number of output revolutions and engine
r.p.m. are shown in Table 4.1.
The values refer to the conditions indicated in the table.
Higher values for occasional use must be agreed upon as each occasion arises depending on the type of use.
Check the vehicle to ascertain whether it is possible to fit a power take-off suitable to its size.
The power take-off applied to the gearbox must only be used when the vehicle is stationary and must be engaged and disengaged
when the clutch is disengaged to avoid excessive stress on the synchronisers during gear change. For special situations when the
power take-off is used and the vehicle is moving the gear must not be changed.
For gearboxes equipped with a torque converter, the same power take- offs used for normal gearboxes are, as a rule, used. It should
be carefully noted that, when the engine r.p.m. is below 60% of the max. value the converter will be in the phase of hydraulic r.p.m.;
in this phase, depending on the absorbed power, the r.p.m. of the power take-off is subject to oscillation despite the fact that the
engine r.p.m. is constant.
Direct Application of Pumps
When the application of pumps of other equipment (e.g. for tippers or cranes) is carried out directly from the power take-off,
without the use of intermediate shafts and after checking that the size of the pump permits margins of safety with chassis and engine
unit (cross member, transmission shaft etc.), the static and dynamic torques exerted by the mass of the pump and by the power
take-off should be checked for compatibility with the resistance of the walls of the gearbox. By way of an example, the moment
due to the additional masses must not have values of over 3% approx. of the maximum engine torque.
In cases where the gearbox is applied in a single unit with the engine, the value of the additional masses must be verified with regard
to the inertial effects in order to avoid the induction of resonance conditions in the engine unit within the field of operational engine
r.p.m.
When fitting power take-offs the torque values shown in Table 4.1 must not be exceeded.
! Transmission oil temperature must not exceed 120ºC during prolonged use. Coolant temperature
must not exceed 100°C. Not all types of power take-off available on the market are suitable for continu-
ous use. When in use the specifications (working periods, pauses etc.) specific to the power take-off
in question should be respected.
Transmission PTO data
The following table shows the types of P.T.O. provided by ZF and by Hydrocar.
The transmission ECU and the Body Computer (BC) will need to be reprogrammed when a PTO is applied after-market. Interven-
tions on the electrical and pneumatic system are required. Read paragraph 4.6 ”PTO management” carefully before applying a PTO.
Re-programming of the electronic control units must be carried out in accordance with the instructions in the IVECO technical
manual using exclusively the diagnostic instrument (available from IVECO dealers and authorised IVECO service centres), providing
the information regardine the specific P.T.O. requirements.
Power Take-off from Gearbox

Table 4.1 - PTO types provided by ZF
N. Ratio Maximum take-off

Transmission Type P.T.O. Assembly side
P.T.O. Total PTO torque (Nm)
5202 ZF -NH/1b center 0.97 800
5205 ZF -NH/1c center 0.97 800
5209 ZF -NH/4b lower 1.24 430 (1)
9S1310 TO 5210 ZF -NH/4c lower 1.24 430 (1)
5258 ZF -N109/10b high 0.97 600
5255 ZF -N109/10c high 1.19 630
5259 ZF -N109/10c high 0.97 600
5202 ZF -NH/1b center 0.91 / 0.77 1000
5205 ZF -NH/1c center 0.91 / 0,77 1000
5209 ZF -NH/4b right 1.17 / 0.98 430 (1)
16 S 1620 TD 5210 ZF -NH/4c right 1.17 / 0,98 430(1)
16 S 1920 TD
5258 ZF -N221 10/B above 1.35 / 1.14 730
16 S 2220 TD
16 S 2320 TD 5260 ZF -N221 10/B above 1.75 / 1.47 560
5264 ZF -N221 10/B above 2.00 / 1.68 470
5255 ZF -N221 10/C above 1.13 / 0.95 870
5259 ZF -N221 10/C above 1.35 / 1.14 730
5202 ZF -NH/1b center 1.09 / 0.91 1000
5205 ZF -NH/1c center 1.09 / 0.91 1000
5209 ZF -NH/4b right 1.40 / 1.17 430 (1)
5210 ZF -NH/4c right 1.40 / 1.17 430 (1)
16 S 2220 TO 5258 ZF -N221 10/B above 1.62 / 1.35 730
16 S 2520 TO
5260 ZF -N221 10/B above 2.09 / 1.75 560
5264 ZF -N221 10/B above 2.40 / 2.00 470
5255 ZF -N221 10/C above 1.35 / 1.13 870
5259 ZF -N221 10/C above 1.62 / 1.35 730
1) Limit 1 hour of use

Table 4.1 - (continued) PTO types provided by ZF
N. Assembly Ratio Maximum take-off

Transmission Type P.T.O.
P.T.O. side Total PTO torque (Nm)
5202 ZF -NH/1b center 0.79 800
5205 ZF -NH/1C center 0.79 800
12 AS 1420 TD 5209 ZF -NH/4b lower 1.01 430 (1)
5210 ZF -NH/4c lower 1.01 430 (1)
5260 ZF -Nm AS/10 b above 1.92 380 (1)
5202 ZF -NH/1b center 0.82 1000
5209 ZF -NH/4b right 1.05 430 (1)
5210 ZF -NH/4c above /H 1.05 430 (1)
12 AS 1930 TD
12 AS 2330 TD ZF N AS/10b
5260 above /H 1.92 400
flange
ZF -Nm
Nm AS/10b above/L/pump 1.21 670
6420
double output lower/H/flange 1.92 400
5202 ZF -NH/1b center 1.35 1000
5209 ZF -NH/4b right 1.22 430 (1)
5210 ZF -NH/4c above /H 1.22 430 (1)
12 AS 2530 TD ZF N AS/10b
5260 above /H 2.15 400
flange
ZF -Nm
Nm AS/10b above/L/pump 1.23 670
6420
double output lower/H/flange 1.73 400
1) Limit 1 hour of use

Power Take---off from Transfer Box / Power Take---off from Drive line
4.3 Power Take-off from Transfer Box
NOTE Not present on Stralis.
4.4 Power Take-off from Drive line
The authorisation for the application of a power take-off on the drive line downstream of the gearbox is issued after examination
of the complete documentation presented to the Company.
The various power and torque values will be evaluated as each occasion arises on the basis of the conditions of use.
In general the following should be noted:
- The drive take-off may be operated only when the vehicle is stationary.
- The power take-off r.p.m. is dependent on the gear selected.
- The power take-off must be located immediately downstream of the gearbox. For vehicles with the drive line in two or more
sections, the power take-off may also be fitted at the flexible support included between the first and second sections (respect
the indications given in point 2.8.2).
- The angles of the drive line on the horizontal plane and vertical plane must be kept as close as possible to the original values.
- Masses and rigidity added to the drive line must not provoke a loss of balance or abnormal vibrations or damage the transmission
drive line (from engine to axle) either during vehicle movement or during operation with the motor running.
- The power take-off must be fixed to the chassis with its own suspension.
NOTE As the transmission is an important part for the safety of the vehicle, modification to it must only be
carried out by specialist companies approved by the supplier of the transmission.
NOTE The power take-offs on the universal joint line cannot be used in conjunction with EuroTronic tran-
smissions!
Power Take-off from Transfer Box / Power Take-off from Drive line
Power Take---off from Engine
4.5 Power Take-off from Engine
In general the use of these power take-offs is planned for apparatus requiring a continuous power supply.
4.5.1 Torque power take off from the front of the engine
The drive take-off from the front part of the crankshaft is obtained, for limited power values to be drawn off (e.g. air conditioning
etc.) by drive belt transmission, the use of coupling shafts is normally reserved for take-offs of a greater magnitude (e.g. municipal
use).
These uses, when not specifically planned, require precise modifications to the front part of the vehicle, e.g. modifications to the
radiator, cab, bumpers etc. Particular attention must therefore be paid:
- To the system comprising additional masses and relative rigidity which must be flexibly disengaged from the crankshaft with regard
to the torsional and flexional effects.
- To the additional mass values and relative moments of inertia and to the distance from the centre of gravity of the masses from
the centreline of the first main bearing which must be kept to a minimum.
- To avoiding a reduction in the radiator cooling capacity and dead water areas.
- To restoring the rigidity and resistance characteristics of the modified elements (cross member, bumper etc.).
- To avoid exceeding, during extended use, temperatures of the engine cooling fluid of over 100°C and engine oil temperature
(measured on the main duct of the pressure switch area) of 110 to 120°C. A margin of approx. 10% should however be left.
In other cases include supplementary heat exchangers.
Table 4.2 shows the values to be referred to for the take-off.
Table 4.2 - Power take-off from front of engine
Max. take-off values

Max. rpm
Max
Engine type Rpm corresp. to admitted (start Max. Max. Max. Moment Multipl.
(power) full power of red band) torque moment of bending multipl. factor
available inertia moment factor ang. pos.
(kW/Cv) rad/s (rpm) rad/s (rpm) (Nm) (kgm2)1) (Nm)2) (-)3) (degrees)4)
Serie Cursor 10 - F3A
E0681E (287/390) 220 2100 283 2700 500 0.050 150 1 0-180
E0681B (294/400) 220 2100 283 2700 500 0.050 150 2 180-210
E0681D (316/430) 220 2100 283 2700 500 0.050 150 3 210-240
4 240-300
3 300-330
2 330-360
Serie Cursor 13 - F3B
E0681G (279/380) 199 1900 262 2500 500 0.050 150 1 0-180
E0681C (324/440) 199 1900 262 2500 500 0.050 150 2 180-210
E0681E (353/480) 199 1900 262 2500 500 0.050 150 3 210-240
4 240-300
3 300-330
2 330-360
1) Maximum moment of inertia of rigidly added masses.
2) Max. moment of flexure due to radial forces in relation to the first main support.
3) Amplification factor of the max. permitted flexural moment (depending on the angular position of the additional radial forces)
4) Direction of the additional radial forces. (zero: TDC cylinder axis; rotation: clockwise).
Power Take-off from Engine

4.5.2 Power take off from the rear of the engine
4.5.2.1 Multipower power take-off on flywheel side
On some models it is possible to install an optional IVECO Multipower power take-off, designed to take off higher torques than
those of other PTOs. This unit is fitted on the rear part of the engine and takes drive from the flywheel. It is independent of the
vehicle clutch drive and suitable for use with the vehicle running and/or at a standstill (e.g. municipal applications, concrete mixers,
etc.).
Some precautions:
- the PTO must be engaged only with the engine at a standstill (a safety device prevents engagement with the engine running
in any case);
- the unit may be disengaged with the engine running but only if power is not currently being taken off;
To guarantee correct engagement, the static a moment of connected units must not exceed 35 Nm.
! According to the version of the connected units, it may be necessary to consider a clutch engageable
by load (weight) in the transmission.
- the engine must be started when no torque is being taken from the PTO.
The main dimensional specifications are given in Figure 4.3/4.4 and Figure 4.5, while the technical specifications are given in Table
4.3.
Figure 4.3
180 91524

Table 4.3
Output rpm/engine rpm ratio 1.29

Max. torque available 900 Nm
Output flange ISO 7646-120 X 8 X 10
Control pneumatic
Direction of rotation as engine
Installation on engines Cursor 8-10-13
If turned on during transfers, you must be well aware that depending on the gearing ratio of the power take-off (see tab. 4.3), con-
nected pumps may reach high rotating speeds (e.g.: an engine speed of 1800 rpm corresponds to a pump speed of 2400 rpm).
Consequently, in order to operate FMO FMO (FAST MOVING OBJECTS) equipment with this type of power takeoff, the vehicle
control unit must have the three following function modes enabled:
a) Vehicle in motion
With Multipower engaged and the vehicle in motion, the vehicle control unit must receive the PTO engaged signal.
Acceleration of the vehicle is permitted, but it is not allowed to exceed the 1800 rpm threshold, set in the program of the vehicle
control unit.
b) Pump engaged with accelerator de-activated

After engagement of the pump, if no part of the equipment is in operation (if no loading and unloading operations are being
preformed and the compactor is not engaged), the vehicle control unit receives the pump engaged signal. The rotating speed, set
by the vehicle control unit program, is kept to a minimum and accelerations from the operator are not permitted (if the accelerator
pedal remains de-activated).
NOTE This condition can be found even when, the movement of the equipment is interrupted during oper-
ation because of an alarm.
During emergency movements, for example for the return into the profile of the members, it is advis-
able to carry out the manoeuvres with a reduced motor rotation speed.
Remember that with these enabled pump without accelerator request conditions during normal operation may not be frequent:
in fact the compactor is always on during normal equipment operation and this implies the accelerator enabling request.

c) Pumps engaged with accelerator activated

After engauging the PTO pump and with the equipment in operation (loading, unloading and compacting operations), the vehicle
control unit receives the accelerator request signal.
The rotating speed set by means of the vehicle control unit, is carried to the optimal value required to obtain the oil flow capacity
required for equipment operation.
Even in this stage the operator cannot accelerate.
Therefore, three different vehicle rotating speeds and thresholds are required and must be obtained by means of three different
signals that are to be sent by the equipment to the vehicle control unit.
FMO equipment without Multipower operate only on function b and c.

!
4.5.2.2 Power take-off from the timing gears at rear of engine
Models equipped with engines of the Cursor 8 and Cursor 13 series are supplied with friction clutch power takeoff which picks
motion from the distribution gears, independently from the vehicle’s clutch.
The power takeoff is available in the direct pump mount version, or with a flange for Cardan shaft.
The installation of this power takeoff must be requested when ordering the vehicle; subsequent applications require the replace-
ment of the whole engine.
Figure 4.4 shows diagrams with dimensions and position of the PTO in relation to the engine and vehicle.
Table 4.4 gives the main data.
To take off a max. torque of 600 Nm (CURSOR 8) and 800 Nm (CURSOR 10/13) the moment of inertia of the rotating masses,
movement after the power take-off (including the coupling shaft), must be no greater than: 0.03 Kgm2.
In no case must the max. available torque of 600 Nm (CURSOR 8) and 800 Nm (CURSOR 10/13) be exceeded.
Direct pump application

The static moment due to the added masses must not exceed 90 Nm, measured on the pump mating surface.
Connection with coupling shaft

On exceeding the maximum admissible value of the inertia, given above, it is necessary to apply a flexible coupling, specifications
of the coupling to be requested directly to IVECO.

Figure 4.4
124476
Table 4.4 - (Illustrative examples of possible configurations)
Type engine PTO A / Flange A / Pump B C

Type Hydrocar
Cursor 8 F210 555 mm 589 mm 73 mm 154 mm

Power take-off from timing gears for Eurotronic 2 transmissions
Figure 4.5
Flange attachment
DIN 10
OPTION 5367
Flange attachment
ISO 4 fori - 7653
OPTION 6366
124477
NOTE It is, however, necessary to check compatibility between the pump to be applied and the fitting case
by case.
Table 4.5 - PTO Specifications

Power take-off
Engine
g Max. torque Output type
available for Out rpm/engine Direction of
rpm ratio Pump conn. Flange conn. rotation
drawing Nm
Opposite
CURSOR 10/13 800 1.12 ISO 4 holes (7653) DIN 10
to engine
Opposite
CURSOR 8 600 1.14 ISO 4 holes (7653) DIN 10
to engine
NOTE PTO can be equipped with a pneumatic disc clutch in oil bath system.

Torque limits available from PTO according to engine speed
Figure 4.6
91527
A. Take-off torque - B. Engine rpm

CURSOR 10/13
Vehicle programming
- Vehicle stopped - PTO mode ON

Take-off of up to 800 Nm of torque is permitted at engine speeds of over 1100 rpm.
- Vehicle running - PTO mode ON
- no limit to the torque obtainable from the power takeoff according to engine revs;
- engine idle running set to 700 r.p.m.;
- the air supply system pressure fot PTO clutch coupling must be above 8.5 bars.
Figure 4.7
Take-off torque (Nm)
91526
Engine rpm
CURSOR 8
Vehicle programming
- Vehicle stopped - PTO mode ON

Torque drawing of 600 Nm is permitted over 1100 r.p.m.
- Vehicle running - PTO mode ON
- no limit to the torque obtainable from the power takeoff according to engine revs;
- engine idle running set to 800 r.p.m.;
- the air supply system pressure for PTO clutch coupling must be above 8.5 bars.

PTO management
4.6 PTO management
Operations which do not comply with the instructions specified by IVECO or made by non qualified
! personnel can cause severe damage to on-board systems, effect driving safety and good operation of
the vehicle and cause considerable damage which is not covered by warranty.

PTOs are activated electrically by means of a solenoid and their use always involves the programming of 2 control units: Expan-
sion module (EM) and Vehicle Control Module (VCM).
The EM is able to drive up to three PTOs and controls their activation and the activation independently.
PTO management also makes it possible to considerably simplify conversion because it incorporates a set of safety and control func-
tions such as, for example, engagement under certain limit conditions and control during operation.
4.6.1.1 Definitions
The most important aspects of PTO Management are described in detail in the following paragraphs. Firstly, however, some
definitions must be given for a better understanding of the explanations given below.
MUX
The term MUX describes a set of two control units: Body Computer (BC) and MET (frame electronic module).
This network is connected to other electronic systems such as the EDC, EBL, EuroTronic 2, Instrument Cluster, etc Information
and messages are exchanged by means of Bus CAN lines.
PTO switch (PTOsw x, x=1,2,3)

Switch located in the middle of the dashboard (control panel). This is used to request an action relating to a given PTO (e.g.
PTO engagement, PTO disengagement, intermediate speed activation etc.).
Because the EM and VCM are able to control up to three PTOs, this number may be installed on the switches (from PTOsw1 to
PTOsw3).
Each switch is connected to a given pin on connector ST14A.
Connector ST14A
Connector ST14A provided specifically for body builders is located on the passenger side below the electric control unit in the
footwell. More detailed information is given in Chapter 5.
PTO Mode x ( x=1,2,3)

Following a request from a PTO switch on the dashboard, a PTO mode makes available a set of parameters that allow regular
PTO operation. A PTO mode includes:
- a PTO configuration (described below)
- a fast mode (option, described below)
It is possible to activate up to three PTO modes simultaneously.
PTO management
PTO Configuration
The PTO configuration is an integral part of a PTO Mode. This includes a set of parameters for mechanical engagement of a
PTO. Various parameter sets are available for the different PTOs (depending on the engine and transmission). These guarantee PTO
engagement is compliant with requirements. The PTO configuration may be customised by Iveco Service upon the specific request
of customers. The PTO configuration is stored in the EM, VCM control units.
Speed mode x ( x=1,2,3)

A speed mode may be activated as part of a PTO mode (option). This makes available a set of parameters that defines the engine
reaction in the event of activation (intermediate speed, min speed, max speed, accelerator deactivation etc.). This configuration is
stored in the Vehicle Control Module (VCM).
NOTE Because the engine only acts on the basis of a set of parameters, a choice must be made if more speed
modes are requested at a certain point. This takes place on the basis of a scale of priorities.
It is absolutely necessary to consider these priorities in management of the conversion!
4.6.1.2 Diagram functions

Two conditions must be met in order for a power take-off to operate:
1) Mechanical engagement of a power take-off
2) Allocation of a speed mode to this power take-off (option). The definition of a speed mode is explained in this Chapter.
The expression ”active power take-off” means that the power take-off engaged (active end-travel switch) and a speed mode have
been activated.
In each case, a power take-off must be electrically controlled by means of an electromagnetic valve.
PTO management
Only management of the power take-offs through the EM control unit ensures comprehensive, reliable and safe PTO management.
Only in this way is it possible to guarantee the connection with other vehicle functions.
Operating the power take-off without connection to the EM control unit may cause damage to the vehicle.
Connection to the EM control unit presupposes activation and electrical control of the power take-offs (by means of electromagnetic
valves). Air-activated power take-off and/or without connection to the EM control unit are not therefore recommended by IVECO.
NOTE The electromagnetic valve used to activate a power take-off is connected in the chassis to the relevant
ST91 connector (PTO1) / ST92 (PTO2) / ST93 (PTO3).
An electromagnetic valve is allocated to each power take-off via a PTO mode.
If the power take-offs are used without connection to the EM control unit, a logical connection to the
! status signals, namely ’parking brake applied’, ’vehicle parked,’ ’reverse not engaged’ is absolutely
necessary to ensure safe operation of the power take-off and prevent damage.
These signals must be detected by the ST14A interface connector in the cab.
With ADR vehicles, the use of a PTO without connection to the EM control unit is not permitted!
4.6.1.3 PTO switch

The following photograph shows the installation position of a PTO switch (PTOsw 1, right). As already mentioned, up to three
PTO switches may be fitted in the dashboard.
PTO switch Connected to IVECO Part

Description
ST14A Number
PTOsw1 18 PTO1 50409 6567
PTOsw2 19 PTO2 50409 6566
PTOsw3 20 PTO3 50409 6565
NOTE The command may be also given on vehicles with a Eurotronic transmission directly on ST14A.
The PTO switches may be purchased directly through IVECO. The table summarises the part
numbers.
PTO management
4.6.2 PTO modes
Operation of a power take-off is generally determined by:

1) PTO configuration
2) Speed mode
The terms PTO configuration (4.6.2.1) and speed mode (4.6.3) are explained below.
4.6.2.1 EM - PTO 1, 2, 3 configurable
Depending on the planned use of the vehicle, body builders are bound to contact IVECO Service in order to carry out the necess-
ary programming of the controls involved (EM, VCM, EuroTronic Transmissions) in the operation of a power take-off.
Body builders may examine the following tables to organise the configuration of a system in advance (described as PTO configuration
below).
A PTO unit may then be selected.
If the body builder needs custom settings, these may be programmed via IVECO Service for each individual power take-off.
As already mentioned, the body builder is bound to scrupulously observe mode priority in conversion
! management and in the event of reprogramming in order to avoid extra expense for subsequent
changes to the wiring or reprogramming.
PTO management
4.6.2.2 EM - PTO 1, 2, 3 Programming

PTO programming includes the following function groups:
1) PTO switch functionIdle running actuation
Possibility of choosing between:
- physical activation of PTO only
- physical activation of PTO and activation of speed mode
- activation of speed mode only.
2) PTO hardware
For the selection of:
- PTO type including PTO activation and feedback method (status signal).
3) Conditions for mechanical engagement of the PTO (see the following table for EM programming)
The selection determines which conditions must be satisfied in order to engage the PTO mechanically (electrical activation by means
of the electromagnetic valve).
4) Conditions for mechanical engagement of the PTO (see the following table for EM programming)
The selection determines the conditions and the limit values that must not be exceeded or that must at least be reached, respectively.
If the set values are not respected, the speed mode will be deactivated with consequent mechanical deactivation of the PTO. At
the same time, a message will be displayed on the IC (instrument cluster).
5) Extended functions (see the following table for programming in EM)
- dynamic behaviour relating to PTO activation/deactivation.
The adjustments within the five function groups may be defined separately for each PTO mode x 1,2,3 .
1) PTO switch function
The EM control unit controls the PTO modes and speeds by means of a PTO SW switch from 1 to 3 allocated on each individual
occasion, located in the dashboard, which is connected to the relevant pin of the ST14A connector.
Operation of the switch may determine one of the following actions:
Table 4.6
1 (Mechanical engagement of the PTO in conjunction with a given PTO configuration)

2 Activation of speed mode
3 Mechanical engagement of the PTO (in conjunction with a given PTO configuration) and activation of speed mode
4 No effect
Each switch is allocated to a PTO, in other words two switches are required if two PTOs are fitted.
Activation of a PTO by the EM is always connected to a switch operation. Switch operation should not, however, necessary lead
to engagement of a PTO (see table above).
Each switch may be allocated its own PTO configuration. A switch operation also activates fast mode, a selection must be made
in the case of simultaneous operation of various switches. The following priority must be observed:
- PTO 3 configuration (PTOsw 3): Maximum priority (PTOsw 1 and 2 status is ignored)
- PTO 2 configuration (PTOsw 2): Medium priority (PTOsw 1 status is ignored)
- PTO 1 configuration (PTOsw 1): Minimum priority
As mentioned previously, the bodybuilder is bound to scrupulously observe mode priority in the
! management of the conversion and in the case of reprogramming in order to avoid additional
expenses for subsequent wiring changes or re-programming.
PTO management
2) PTO hardware. The following PTOs may be installed and activated
Table 4.7
Definition
Predisposition, no PTO installed
PTO dependant on engine (PTO engines), controlled via the EM
PTO on manual gearbox, controlled via the EM
Switchable multi-power, controlled by the EM
PTO on Allison transmission, controlled via the EM
PTO n1 on EuroTronic transmission, controlled via the EM
PTO n2 on EuroTronic transmission, controlled via the EM
PTO on distributor gear, controlled via the EM
ZF NMV, controlled via the EM
On one vehicle, up to 3 of these PTOs may be installed and managed simultaneously.
3) Selection of conditions for engagement of a PTO
Table 4.8
Parameter Option 1 Option 2 Option 3

Service brake Operated Not operated Not controlled
Handbrake Operated Not operated Not controlled
Clutch status Operated Not operated Not controlled
Clutch timeout secs
Connector ST 91/92/93 Pin 3 Open Earthed Not controlled
Coolant temperature 40 -100˚C Not controlled
Clutch slip limit Not controlled
Expansion module press switch (not
active)
Min rpm for engagement 650- rpm Not controlled
Max rpm for engagement 700- rpm Not controlled
Minimum vehicle speed 0 Km/h Not controlled
Maximum vehicle speed 1 Km/h Not controlled
Lowest speed engaged Not controlled
Highest speed engaged Not controlled
Gear in neutral In neutral Gear engaged Not controlled
Reverse Engage Not engaged Not controlled
The power take-off is engaged only if all conditions are met. If one of the conditions is not met, the EAM displays a warning message
within a short space of time (10 seconds standard) and stops the engagement procedure. PTO engagement must be requested again
(deactivation and reactivation of the PTO switch).
PTO management
4) Selection of conditions for deactivation of a PTO
Table 4.9
Parameter Option 1 Option 2 Option 3

Service brake Operated Not operated Not controlled
Handbrake Engage Not engaged Not controlled
Clutch status Operated Not operated Not controlled
Clutch timeout secs
Connector ST 91/92/93 Pin 3 Open Earthed Not controlled
Coolant temperature 40 -100˚C Not controlled
Clutch slip limit Not controlled
Expansion module press switch (not
active)
Min rpm for engagement 650- rpm Not controlled
Max rpm for engagement 700- rpm Not controlled
Minimum vehicle speed 0 Km/h Not controlled
Maximum vehicle speed 1 Km/h Not controlled
Lowest speed engaged Not controlled
Highest speed engaged Not controlled
Gear in neutral In neutral Gear engaged Not controlled
Reverse Engage Not engaged Not controlled
The PTO is engaged as soon as one of the set conditions is not met, i.e. the speed is reduced and the PTO is mechanically deactivated.
At the same time, a message will be displayed on the IC (instrument cluster)
When selecting the activation/deactivation parameter, care must be taken to ensure no plausibility is violated (for example, activation
condition: Brake pedal operated and simultaneously condition for deactivation: Brake pedal operated).
Full function in this case too is possible only with the power take-offs operated electrically. If the power take-offs are operated pneu-
matically, the control unit is not able to control a power take-off in any way.
5) Extended functions (see the following Table 4.10)
Dynamic behaviour in relation to PTO conditions

The EAM control unit expects certain conditions to be met within a certain time period (standard 10 seconds) after the PTO
request. Once this period has elapsed, the PTO request is rejected and an error is displayed.
The time interval is programmable (0 - 10s). The PTO switch must then be operated again.
Dynamic behaviour for PTO engagement

Establishes the interval after which a PTO must be mechanically engaged after the request. If the set interval is exceeded, the
request is rejected and an error is displayed.
Dynamic behaviour in relation to PTO deactivation conditions

If a deactivation condition arises once a set time interval has elapsed (10 seconds standard), actions are taken for deactivation
and an error is displayed. The time interval is programmable (0 - 10s).
PTO management
Dynamic behaviour on PTO deactivation

Establishes the interval after which a PTO must be mechanically disengaged after the request has been made. If the time interval
is exceeded, an error message is displayed.
Dynamic behaviour in relation to the clutch and PTO engagement

Establishes a minimum time interval within which the clutch must be operated before PTO engagement is permitted and carried
out (to be used only with manual transmission).
Dynamic behaviour in relation to error identification

Time that elapses before an error activates Degraded Mode
Dynamic behaviour in relation to Degraded Mode activation (see information below for more details)
If no confirmation is received from the driver within a certain time interval after Degraded Mode activation, PTO operation is
discontinued and an error message is displayed on the IC (Instruments Cluster). If the timeout is set to 0, PTO operation is immedi-
ately suspended.
Table 4.10
Parameter Condition 1 Condition 2

Timeout at activation 1 - 10 secs. Not controlled
Time out at PTO activation conditions 1 - 10 secs. Not controlled
Timeout at activation via switch 1 - 10 secs. Not controlled
Time out at PTO deactivation conditions 1 - 10 secs. Not controlled
Timeout for error identification 1 - 10 secs. Not controlled
NOTE In general, all the activation and deactivation and Timeout control condition parameters must be set
as to ”is not controlled” as far as possible in order to rule out unnecessary sources of error.
4.6.3 RPM Mode (to be set in the VCM control unit)
A speed mode may be allocated to a PTO within the centralina VCM. The speed mode may be activated directly by means of
a PTO switch or after a successful PTO engagement (based on the programmed PTO switch function).
PTO management
4.6.3.1 RPM 0 mode (driving mode)
When the vehicle speed is below 25 km/h, example, an intermediate engine RPM may be activated.
Activation of an intermediate speed may take place by activating the Resume function, from SET+ or SET- on the control lever
either or by means of the respective inputs of bodybuilder’s connector ST14A.
The intermediate engine rpm on a standard vehicle is set to 900 rpm and may be altered on the basis of the following procedure:
1. activate Resume
2. adjust the speed to the required level using SET+ or SET-
3. activate the Resume function for at least 5 seconds in order to store the set speed.
The speed adjustment range with the gearbox in neutral is set to 100 RPM. It may be increased up to 200 rpm. The selective setting
will then apply also to the speed modes
Speed mode ”0” will be considered the standard speed mode. For safety reasons, it is not possible to alter the following settings
Table 4.11
Parameter Function
Resume/OFF Activation/deactivation of the intermediate speed
SET+/SET- Increase/reduction of the intermediate speed
- Brake or clutch pedal depression
Conditions leading to deactivation of the intermediate speed - Operation of CC Off on the control lever on ST14A
- Activation of the engine brake/Intarder
Accelerator Active
Maximum engine speed with SET+ NLL - 1800 rpm
NLL - 2700 rpm (Cursor 8)
Maximum engine speed with the accelerator pedal
NLL - 2340 rpm (Cursor 13)
Engine torque Maximum torque according to the engine
4.6.3.2 Configurable rpm mode 1, 2, 3
For each programming action, it is possible to establish three independent parameter sets for engine control (on the basis of
speed modes from 1 to 3).
With the simultaneous activation of several imports, it is necessary to determine an import priority with regard to engine control.
The following priorities are set for this purpose:
- speed mode 3: Maximum priority (speed modes 1 and 2 are ignored)
- speed mode 2: Average priority (speed mode 1 is ignored)
- speed mode 1: Minimum priority
The bodybuilder must observe these priorities during management of the conversion and the con-
! version interface. This is to avoid additional expenses for subsequent changes to the wiring or
reprogramming.
The following table provides an overview of parameters that must be determined individually for
each mode (programming by IVECO Service).
PTO management
Table 4.12
Parameter Option 1 Option 2

Engine speed adjustable by means of Set+ 1) 550- 1800 rpm
Engine speed adjustable by means of Set- 2)
Maximum torque 3) According to the engine
Theoretical speed in neutral 4)
Angular coefficient of torque curve NM/rpm
Speed threshold for PTO/CC activation (km/h) 5) 1 Km/h
Speed deactivation with handbrake not engaged Yes No
Activation of parameters for maximum PTO speed 6) Yes, by selection No
Maximum PTO speed (kms/h) 7) 1 Km/h
Speed deactivation by operating brake pedal 8) Yes No
Speed deactivation by driver operating brake pedal 9) Yes No
Speed deactivation by driver operating Intarder 10) Yes No
Speed deactivation by operation of engine brake by means of CAN Yes No
Speed deactivation by operation of Intarder by means of CAN Yes No
Speed deactivation by operation of clutch 11) Yes No
Speed deactivation if this is lower than that set as minimum speed 12) Yes No
Speed deactivation if this is higher than that set as maximum speed 13) Yes No
Speed the activation due to an error in the CC module 14) Yes No
PTO management
Table 4.13

Speed deactivation in the event of communication of service brake and Yes No
parking brake switch error 15)
Deactivation of the accelerator pedal. Yes No
Resume function on start-up Yes No
Maintenance by key of Resume function of other PTO operating modes Yes No
16)
Speed deactivation in the case of a speed sensor error 17) Yes No
Speed deactivation in the case of exceeding coolant temperature 18) Yes, by selection No
Coolant temperature (˚C) 80˚C- 110˚C
Speed deactivation with gear engaged 19) Yes No
Speed deactivation with reverse engaged 20) Yes No
Activation for control of the lowest speed for PTO engagement/disen- Yes, by selection No
gagement 21)
Lower speed for speed activation/deactivation 1st-5th gear
Activation for control of the highest speed for PTO engagement/disen- Yes, by selection No
gagement 22)
Highest speed for speed activation/deactivation 1st-5th gear
CC regulation and memo function 23) See description Voir la description
Engine speed via memo 24) Final speed 550-LL
Maximum speed by means of Set+ 25) 1 Km/h
Temporary activation of engine speed increase from another control Yes No
device 26)
Temporary activation of speed increased by driver 27) Yes No
4.6.3.3 Custom settings
Table 4.14

Activation for a reserve speed Yes, by selection Not controlled
Reserve speed value (km/h) 28)
Limitation of torque according to engine speed (rpm)
Limitation of torque according to torque momentum (Nm)
PTO management
4.6.3.4 Setting for special functions
Table 4.15
Parameter Option 1
Increase/reduce speed by operating Set+/Set- (rpm) 29)
Time required to reach selected speed 30)
Speed deactivation by means of an external torque momentum request
(Nm)
4.6.3.5 Footnotes on 4.6.3.2/4.6.3.3/4.6.3.4
1. Maximum rpm may not be exceeded using Set+ .

2. Minimum rpm may not be exceeded using Set-.
3. To avoid damage to the PTO and transmission, engine torque should be adapted to the PTO
4. Maximum variable rpm of engine with no load Warning: This speed (rpm) differs from the PTO speed according to the PTO
transmission ratio!
5. Up to this setting, the intermediate speed regulator is active in the following PTO modes (it regulates engine speed independently
of the gear) If the set value is exceeded by pressing Set+ again, automatic switching takes place to CC mode (Cruise Control:
speed is suggested independently of the gear).
6. If this value is exceeded, the intermediate speed will be deactivated and the speed will return to the value indicated in NOTE
25.
7 If the set speed is exceeded, the set intermediate speed will return to the value indicated in NOTE 25. Despite possible speed
fluctuations, the value is always 5 km/h lower than the set value. If the value is changed, the value indicated in NOTE 25 is also
automatically changed.
8 The intermediate speed is deactivated and returns to the value indicated in NOTE 2
9. The intermediate speed is deactivated and returns to the value indicated in NOTE 2
16. If the setting is on ”Yes”, these speed of the previously engaged mode is maintained, despite switching between the individual
speed modes. If the setting is ”No”, the speed is adjusted to that of the corresponding selected mode (considering priority).
18 The intermediate speed is deactivated and returns to the value indicated in NOTE 2
19. If the setting is ” Yes”, fields 20, 21 and 22 are active. If the setting is ”No”, no input is possible in these fields.
20. -22 becomes an unsatisfied condition. The intermediate speed setting returns to the value in NOTE 2.
PTO management
23. Three adjustment options are available in this case

Option 1:
No possibility of calibration! The speed set at point 19 is fixed and cannot be altered by the driver by means of SET+ SET- .
Option 2:
Calibration is possible: The speed set at point 24 is fixed and may be adjusted by the driver using SET +/Set - on the basis of
the adjustment range shown in Point 1 and 2.
Option 3:
With calibration and possibility of storage: The speed set at point 24 is fixed and may be adjusted by the driver using SET +/Set
- on the basis of the adjustment range shown in Point 1 and 2 and stored as a new speed.
24. If a speed is already stored, this will be automatically activated at the time of engagement. This speed may be altered, as described
under Point 23
25. Speed that may be achieved at maximum with SET+
26. Must be set to ”No”! With the programming on ”YES” intermediate speed may be imposed by the EuroTronic transmission
switching procedure! One consequence of this could be a PTO over speed.
27. Must always be set to ”No” to ensure that the Kickdown function is excluded. If set to ”Yes”, the driver could exceed the set
speed limit by operating the kickdown function.
28 If a power take-off is used on the universal shaft (N90 - Omsi - etc.), it is possible to engage a speed higher than 90km/h in this
case in order to allow it to work in the highest gear with high engine RPM without the speed limit cutting in.
29. Possibility of adjustments to alter rpm each time Set+/-is pressed
30 The speed control activates after a correction time (time during which the modified signal remains uninterrupted in order to
be accepted as valid) in the new selected speed mode (pin connector ST14 pin 18,19,20). This correction time may be shortened
in relation to the factory setting (500 ms), down to 100 ms.
PTO management
4.6.3.6 Changes to the torque curve, final rotation speed and steepness of the final limiter
For mechanical power take-off protection, it is possible to limit:

a) engine torque delivery as a protection against overload
b) engine rpm, as a protection against over-speed
The diagram in fig. 4.8 shows this qualitatively by means of a toque/engine RPM curve (defined by 16 points), a horizontal section
(representing torque limitation) and a sloping section (representing over-rev adjustment).
Figure 4.8
Rpm
[rpm] 114514
1. Resultant curve - 2. Maximum torque straight limitation line - 3. Out of rev curve - 4. Curve points
After setting a maximum for engine RPM and a variation mode (slope 3), we obtain a point of intersection X with the straight line
of the set torque and therefore the maximum RPM compatible with this torque on the x-axis.
In other words: As the engine RPM increases, the control unit uses the lowest torque value between those on curve 1 and those
on straight line 2 and then, for speeds greater than that determined by point X, causes the over-revving adjustment device to cut
in and thus reduce the torque.
PTO management
Please note that:

- The bodybuilder chooses the engine speed up to which the selected torque must available according to the use planned for
the PTO
- The speed referred to is that of the crankshaft and not that of the PTO, for which the RPM must be calculated taking into account
the reduction ratio (tab. 4.3 on page 4-11)
- These limitations (maximum torque, intersection point and curve gradient) may be selected independently of one another. It
is, however, advisable to set a combination
- These parameters may only be activated by IVECO.
Figure 4.9
Maximum
torque [Nm] Curve B
Curve C
Curve A
Overrun regulator curve

600 Nm gradient:
Varying overrun
0 ÷ 0.2 rpm/Nm
Intersection
point X
Rpm
[rpm] 126134
We will take a look at the example in Figure 4.9:

- Max engine torque 600 Nm
- Standard power take-off operation is specified at 900 rpm.
- The engine rpm must not exceed 1100 rpm
- The rpm must be calculated for all overrevving rpm regulator gradients
The corresponding power at 1100 rpm and a torque of 600 Nm gives (see equations on page 4-3)
P = (600 Nm x 1100 rpm)/9550 = 69 kW= 94 hp
The overrevving regulator curve gradient depends on the specific application.

With stationary operation, a steep overrevving rpm adjustment curve is therefore generally sufficient, while in driving mode this may
give rise to rapid load changes (which could be a problem).
Therefore:
- with regulator at 0.05 rpm/Nm (curve C in figure), a torque of 600 Nm is available up to 1100 - (0.05 x 600) = 1070 rpm;
- with regulator at 0.1 rpm/Nm (curve B), the torque is available up to 1040 rpm;
- with regulator at 0.2 rpm/Nm (curve A), the torque is available up to 980 rpm;
PTO management
PTO management
4.7 PTO management
4.7.1 No PTO installed or provisions for PTO:
Default configuration
PTO-Option 5194, 6368, 1483, 1484.
Only the programming of the engine revolutions by the VCM is required.
The switches select the three rpm modes:
Table 4.16
PTO 1 PTO mode 1 900 [tr/min]

4.7.2 PTO Multipower
PTO option: 2395 for all gearboxes.

Only the programming of the engine revolutions by the VCM is required.
The switches select the three rpm modes:
NOTE These conditions can be modified in Customer Service.
Table 4.17 - Activation conditions
State of engine OFF

Pressure switch closed
State of vehicle stationary
Coolant temperature < 120 [°C]
Table 4.18 - Deactivation conditions
Coolant temperature > 120 [°C]
PTO management
4.7.3 PTO manual gearbox with electric engagement
PTO options: 6392, 6393, 1459, 1505, 1507, 1509, 6384, 14553, 14554 for all manual gearboxes.
State of engine ON
State of engine OFF

4.7.4 Allison gearbox PTO
Allison automatic gearbox option: 8292 (PTO included)
State of engine ON
State of gearbox neutral
State of engine OFF

PTO management
4.7.5 PTO FOCSA
PTO option: 5151
State of engine ON (always enabled)
State of engine OFF
4.7.6 PTO engine
PTO options: 5367
State of engine ON
State of vehicle OFF

PTO management
4.7.7 PTO Eurotronic 2 transmission
State of gearbox enabled

State of engine ON
State of vehicle OFF

PTO management
EM (Expansion Module)
4.8 EM (Expansion Module)
The optional 4572, EM (Expansion Module), is available on all the new Stralis.
The EM control unit can be used for electrical management of the PTO and for special applications. Also provides special gateways
such as: trailer interface ISO11992-3 (TT) and CAN OPEN interface (BB in development phase).
Diagnostics is possible via CAN line and K line.
The wiring diagram for the Expansion Module hardware is shown in Figure 4.10, and the block diagram of the hardware structure
is shown in Figure 4.11.
Figure 4.10
123241
1. PTO switch - 2. EM ECU - 3. PTO solenoid valve - 4. PTO on - 5. Configurable PTO enablement.
Figure 4.11
123242
The EM control unit allows the PTO activation and deactivation conditions to be set.
The connections on ST91, ST92 and ST93 must be carried out by the fitter so as to activate and display on IC the activation of
the PTO.
The predefined set conditions for Stralis Euro 4-5 are:
4.8.1 Connections
Table 4.29 - PTO mode request: ST14A
PTO 1 pin 18
PTO 2 pin 19
PTO 3 pin 20
To carry out the request, close the pins on the earth of pin 17.
Table 4.30 - PTO IN/OUT: ST91 PTO1, ST92 PTO2, ST93 PTO3
pin 1 PTO feed-back

pin 2 PTO actuator (solenoid valve control)
pin 3 PTO enabling
pin 4 Ground
STRALIS AS/AT/AD Euro 4/5 SPECIAL INSTRUCTIONS FOR ELECTRONIC SUBSYSTEMS 5-1
Index
SECTION 5
Special instructions for electronic subsystems
Page
5.1 Electronic system 5-3
5.1.1 Description of ECUs 5-3
5.1.1.1 Instrument Cluster (IC) 5-4
5.1.1.2 Body Computer (BC) and Cab Module (CM) 5-4
5.1.1.3 Bulkhead coupling (passage of electrical wiring) 5-5
5.1.1.4 Front Frame Computer (FFC) 5-5
5.1.1.5 Rear Frame Computer (RFC) 5-6
5.1.1.6 Expansion module (EM) 5-7
5.2 Bodybuilder connectors 5-8
5.2.1 In the cab 5-8
5.2.2 On frame 5-15
5.2.3 Truck/trailer connectors 5-18
5.3 Electrical circuit modifications 5-21
5.3.1 Introduction 5-21
5.3.2 Wiring harness length 5-21
5.3.3 Repositioning ECUs 5-22
5.3.4 Disconnecting ECUs 5-23
5.4 FMS 5-24
5.5 Electrical System: Modifications and Drawing-Off Power 5-26
5.5.2 Electromagnetic compatibility 5-27
5.5.3 Additional equipment 5-33
5.5.4 Taking current 5-36
5.5.5 General battery switch 5-36
5.5.6 Additional circuits (fuses and conductor cross-section) 5-39
5.5.7 Harness Modifications due to Changes to Wheelbase or Overhang 5-40
5.5.8 Power Draw-off at a Voltage Different from that of the System 5-40
5.5.9 Side Marker Lamps 5-40
Index
5-2 SPECIAL INSTRUCTIONS FOR ELECTRONIC SUBSYSTEMS STRALIS AS/AT/AD Euro 4/5
Index
55555.
Electronic systems
5.1 Electronic systems
Stralis is equipped with an innovative electronic system, called Multiplex (MUX). The system electronically manages and controls
the vehicle subsystems on CAN lines. The most important characteristics of devices are shown in the paragraphs that follow.
5.1.1 Description of ECUs
The location (Figure 5.1) and functions of the ECUs (electronic control units) installed in the vehicle are illustrated below for
a better understanding of the Multiplex system.
Devices or electrical circuits cannot be directly connected to the ECUs described below. Always only
! use the connectors and special interfaces listed in the following paragraphs (bodybuilder connectors
5.2)!
Figure 5.1
123760
1. RFC on trucks - 2. RFC on tractors - 3. BM Bed Module - 4. AHT.A (additional heater) - 5. BC Body Computer -
6. Terminal board - 7. CC Climate Control - 8. AHT.W (additional coolant heater) - 9. FFC Front Frame Computer -
10. IC Instrument Cluster - 11. DDM Drive Door Module - 12. PDM Passenger Door Module - 13. Cab Module (Ordenador
bastidor) - 14 Vehicle Control Module (VCM) - 15. Central locking - 16. Electronically-controlled air suspension (ECAS) -
17. EM (Expansion Module)
Electronic systems
5.1.1.1 Instrument Cluster (IC)
The Instrument Cluster (IC) control panel forms the interface between driver and vehicle.
All vehicle statuses such as vehicle speed, engine rpm, coolant temperature and fault reports are indicated via the driver’s control
panel. It is not possible to select or take individual displays directly (e.g. control warning lights). This is possible only using the appropri-
ate planned connection points.
Figure 5.2
5.1.1.2 Body Computer (BC) and Cab Module (CM)
Illustration 5.3 shows the vehicle’s central control unit, the Body Computer. All the input and output signals that are important
for interaction with individual vehicle systems are processed here.
When non-permitted vehicle states arise, the information is sent from the Body Computer to the Instrument Cluster so that the
driver can be informed via the fault warning lights. The fuses and relays are also housed in this sector.
Figure 5.3
Electronic systems
5.1.1.3 Bulkhead coupling (passage of electrical wiring)
The subsystems fitted on the body are connected to the ECUs in the cab via the terminal board which is the interface for con-
nectors on body and cab side. It is located under the hood.
Figure 5.4
98897
5.1.1.4 Front Frame Computer (FFC)
The Front Frame Computer sends and receives information on all components that are arranged in the front part of the vehicle,
for example the front lighting system or the brake and engine system sensors.
Information is forwarded by means of the Body Computer to those vehicle systems to which this information is relevant.
Figure 5.5
Electronic systems
5.1.1.5 Rear Frame Computer (RFC)
The RFC processes the information from the subsystems and the bodybuilder connectors in the rear part of the body and the
signals from the trailer.
In the truck, the RFC is located behind the rear axle, as shown in Figure 5.6, whereas in the on-road tractor unit for half-trailer it
is located in the centre of the frame, see Figure 5.7.
Figure 5.6
Figure 5.7
Electronic systems
5.1.1.6 Expansion module (EM)
The EM (2) replaces the DMI control device used so far with the Trakker and is located in the passenger footwell. This is con-
nected to the request switches, the electromagnetic valves and the PTO feedback switches. All PTO engagement/disengagement
functions are now programmed in the EM control not and no longer in the Body Computer. The EM is already equipped with a
cable and connectors for future applications that are currently not yet active.
Figure 5.8
0051469t
Electronic systems
Bodybuilder connectors
5.2 Bodybuilder connectors
The various connectors for bodybuilders are described in detail in the following paragraphs.
5.2.1 In the cab

The connectors important for bodybuilders are the ST14 outputs. These are divided as follows: ST14, ST14A, ST14B, ST14C,
and they are installed in accordance with specific requirements. They are housed behind a cover in the passenger footwell.
The ST40 output (FMS output) is housed above the driver in one of the removable DIN cassettes. Parallel to this in the passenger
footwell, a ST40X output is available. Both outputs contain the same CAN communications.
Figure 5.9
123761 123762
21 pin connector (blue): ST14A
Table 5.1 - ST14A Interface connector basic functions
Wire Connected
Pin Description Max. load Remarks
code to
1 Engine Start 8892 10mA VCM X3-27 Engine cranking; earth = cranks engine
(signal must be permanently on until the en-
gine starts);
wire open = no action.
2 Engine stop 0151 10mA VCM X3-26 Engine stopping; Earth = stops engine
(short activation sufficient to stop engine);
wire open = no action.
3 Service brake 1165 200mA VCM X1-13 Signal indicating that the service brake is ap-
plied.
0 V = service brake not applied
+24 V = service brake applied
4 Vehicle standstill 5515 200mA BC2 J5-1 Vehicle stationary signal
0 V = vehicle stationary
+24 V = vehicle moving
Table 5.1 - (Continued) ST14A Interface connector basic functions
Wire Connected
Terminal Description Max. load Remarks
number to
5 Parking brake 6656 200mA VCM - X1-10 Signal indicating that the parking brake is ap-
plied
0 V = disengaged
+24V = engaged
6 Reserved
7 Vehicle speed 5540 10 mA M/DTCO B7 Pulse signal
8 Engine status 7778 150 mA BC2 J7-4 +24V at engine running
9 Gearbox neutral 8050 200 mA VCM X1-7 +24V at neutral engaged
10 Reverse gear 2268 150 mA BC2 J5-5 +24V at reverse gear engaged
11 K15 8871 3A BC2 J3-3 K15 (ignition-operated power point)
CC Set+ input
12 CC Set+ 8156 10 mA VCM X3-33 Open wire = Set + not activated
Close to Ground = Set + activated
CC Set- input
13 CC Set- 8157 10 mA VCM X3-32 Open wire = Set - not activated
Close to Ground = Set - activated
CC OFF input
14 CC OFF 8154 10 mA VCM X3-30 Open wire = Off not activated
Close to Ground = OFF activated
CC RES input signal
15 CC Resume 8155 10 mA VCM X3-31 Circuit open = RES not activated
Connection to ground = RES activated
Selection of CC activation by driver or BB
16 CC driver/BB 0152 10 mA VCM X3-49 Open wire = CC controlled by driver
Close to Ground = CC controlled by BB
17 Ground 0000 10A Wiring Ground
PTO mode 1
VCM X3-47
18 PTO 1 sw 0131 10 mA Open wire = PTO mode 1 not activated
EM X3-5
Close to Ground = PTO mode 1 activated
PTO mode 2
VCM X3-46
EM X3-6
PTO mode 3
VCM X3-45
EM X3-7
Fusible
21 K30 7772 70401-6 K30 (positive from TGC)
10 A
9 pin connector (blue): ST14B
Table 5.2 - ST14B Interface connector basic functions
Wire Connected
Pin Description Max. load Remarks
code to
1 2nd Speed Limiter 8223 10 mA VCM X3 - 13 2nd speed limiter activation
open wire = 2nd SL not activated
+ 24V = 2nd SL activated
2 Economy Power 0166 10 mA VCM X3 - 11 Activation Economy Power (EP)
open wire = EP not activated
close to Ground = EP activated
3 Clutch status 9963 200 mA VCM X1 - 12 To ground = clutch activated
4 PTS 5542 200 mA VCM X1 - 14 Programmable threshold = rpm or vehicle
speed
+24 V = limit exceeded
5 Emergency Lights 1113 10 mA BC2 J4 - 4 Close to ground = Emergency lights on
Open wire = no action
6 Reserved
7 Reserved
8 Engine speed signal 5587 10mA ECM 33 Pulse Signal
9 K58 external lights 3333 5A BC2 J1 - 9 +24V at vehicle lights on
NOTE The pinout for connectors ST14A and ST14B indicated in tables 5.1 and 5.2 are specifically for OBD1
Step 2 vehicles.
The eighth digit of the PIC (Product Identification Code) indicates STEP 2 of the vehicle:
3-4-C-B Stralis AS
3-4-C Stralis AT/AD
12 pin connector: ST14C
Table 5.3 - ST14C Interface connector basic functions (Allison Gearbox for Refuse Vehicles)
Connections
Pin Description Max. Connected Remarks
Type Wire code
load to
Neutral Indica-
OUTPUT Gearbox in neutral: Ground for neutral enga-
1 tor for Extra “145” 0,5A ALL 45
High Side ged
Pto
1st gear limitation and inhibit reverse
Refuse Stepper
2 INPUT “123” 15mA ALL 23 Open wire = function activated
Switch
+ 24V = function not activated
3 - “142” ALL 42
Input from PTO switch
INPUT
4 Pto Enable “143” 15mA ALL 43 Open wire = PTO not requested
+ 24V = PTO requested
OUTPUT PTO enable: +24 Output for solenoid valve
5 Pto Command “130” 0,5A ALL 30
High Side
6 Reserved
7 Reserved
Automatic Automatic Neutral. Logic ”and” mode with pin
Neutral 9
8 INPUT “117” 5mA ALL 17
Dual Input Open wire = function not activated
Close to Digital Ground = function activated
Automatic Automatic Neutral. Logic ”and” mode with pin
Neutral 8
9 INPUT “101” 5mA ALL 1
Dual Input Open wire = function not activated
Digital Ground. Must be used as return for
10 Digital Ground POWER “103” ALL 3 inputs ”Close to Digital Ground”.
Do not connect to -Battery or other grounds
OUTPUT
11 Range indicator “113” 0,5A ALL 13 Gearbox: Ground for neutral not engaged
Low Side
12 Reserved
12 pin connector: ST14C
Table 5.4 - ST14C Interface connector basic functions (Allison Gearbox for Fire Fighting Vehicles)
Connections
Type Wire code
load to
Neutral Indica-
OUTPUT Gearbox in neutral: Ground for neutral enga-
1 tor for Extra “145” 0,5A ALL 45
Low Side ged
Pto
2 - “123” ALL 23
Hold transmission in Neutral.
Auxiliary func-
Logic ”and” mode with pin 2.
3 tion INPUT “142 5mA ALL 42
Open wire = function not activated
Range Inhibit
Input from PTO switch
4 Pto Enable INPUT “143” 15mA ALL 43 Open wire = PTO not requested
+ 24V = PTO requested
OUTPUT
5 Pto Command “130” 0,5A ALL 30 +24 Output to activate PTO by solenoid valve
High Side
6 Reserved
7 Reserved
8 - “117” ALL 17
Hold transmission in Neutral.
Auxiliary func-
Logic ”and” mode with pin 3.
9 tion INPUT “101” 5mA ALL 1
open wire = function not activated
Range Inhibit
Digital Ground. Must be used as return for
inputs ”Close Digital Ground”.
10 Digital Ground POWER “103” ALL 3
Do not connect to -Battery or other grounds
OUTPUT
11 Range indicator “113” 0,5A ALL 13 Gearbox: Ground for neutral not engaged
Low Side
12 Reserved
9 pin connector: ST40
Table 5.5 - ST40 Interface connector basic functions
Connections
Type Wire code
load to
1 K30 POWER 7772 5A K30
2 K15 POWER 8871 5A K15
3 Vehicle speed OUTPUT 5541 10 mA IC 20 Vehicle speed
4 +12 POWER 7712 5A +12
5 CAN H Bus WS/Bi 10 mA VCM X3-37 CAN H
6 CAN L Bus GN/Ve 10 mA VCM X3-38 CAN L
OUTPUT
7 Dashboard light 4442 1A BC2 J7-19 Dashboard light
High Side
OUTPUT
8 Reverse gear 2268 200mA BC2 J5-5 +24V at reverse gear engaged
High Side
9 Ground POWER 0000 5A Ground
6 pin connector: ST 72072A
Table 5.6 - ST 72072A Interface connector basic functions
Connections
Pin Description Wire Max. Connected Remarks
Type
code load to
1 Stopping brake OUTPUT Tbd EM X4-4 6981 Tbd
Gearbox
2 OUTPUT Tbd EM X4-5 6983 Tbd
neutral
3 Dig Input 11 INPUT Tbd EM X3-17 0991 Digital Input
4 External Clutch OUTPUT Tbd EM X1-7 9995 Tbd
5 Reserved
6 Reserved
20 pin connector: ST 72072B
Table 5.7 - ST 72072B Interface connector basic functions
Connections
Pin Description Max. Con- Remarks
Type Wire code
load nected to
6 HS Output 5 OUTPUT Tbd EM X1-3 6985 High side Output
16 AN IN 1 INPUT Tbd EM X4-14 5981 Analog input
19 Freq IN 1 INPUT Tbd EM X4-16 5991 Frequency input
20 Freq IN 1 INPUT Tbd EM X4-38 5992 Frequency input
5.2.2 On frame
The following plug connections are located in the frame area:

- ST52 (for customer-specific solutions)
- ST64 (for customer-specific solutions)
- ST91 PTO output 1
- ST91 PTO output 2
- ST91 PTO output 3
NOTE Output ST 90 (in the case of a manual gearbox), that was introduced with the Stralis construction
series is still used, but is no longer supported and may no longer be used for applications! Output St
67 is no longer available!
Figure 5.10
Tractors: Cabinati:
123763 123764
Figure 5.11
101538
Pin Function Cable color code

1 Plus + 15 for special body makers 8871
2 Ground 0000
3 1) Position lights 3333
4 Negative from secondary speed limiter switch 0172
1) +24 V when:
- K15 OFF and side markers on
- K15 ON and side markers on
- K15 ON and lights on (dipped beam and main beam)
Figure 5.12
101542
For general use by bodybuilders: four terminals in the 15-pole connector can be used for the trailer.

Pin Function Cable color code
1 Current socket supply 8021
2 Current socket supply 7021
3 Connected to trailer output Pin 10 6621
4 Terminal 15 also connected to output ST52 Pin 1 8075
5 Connected to trailer output Pin 11 8075
NOTE ST90 DO NOT use for PTO management.
4 pin connector: ST91 / 92 / 93
Figure 5.13
123765 123246
Table 5.10 - ST91 / 92 / 93 Interface connector basic functions
Pin Description Wire Max. Connected Remarks

number load to
1 PTO feedback signal 6131 (ST91) - EM X3-8 Connection open = PTO not engaged
6132 (ST92) EM X3-9 Earth = PTO engaged
6133 (ST93) EM X3-10
2 PTO activation by 9131 (ST91) 1,6 A EM X1-1 0 V = Electromagnetic valve not activated
means of electromag- 9132 (ST92) EM X1-3 +24 V = Electromagnetic valve activated
netic valve 9133 (ST93) EM X1-6
3 Press switch/digital 0391 (ST91) - EM X3-11 The input may be factory programmed 1)
input 0392 (ST92) EM X3-12
0393 (ST93) EM X3-16
4 Ground 0000 11 A Ground
1) Two input situations may occur:
A to ground = PTO enabled
B connection open = PTO not enabled
Active condition programmed using Easy programming device
Acquistion of pressure switch installed in the factory with the use of Multipower and engine operation power take-offs (engine PTO)
The input may be freely used for other applications in order to connect a required function in the PTO control
5.2.3 Truck/trailer connectors
Two connectors are provided for connecting the trailer:

- 15-pin for electrical devices in general
- 7-pin for vehicles with EBS, or 5-pin for vehicles with ABS + EBL.
Table 5.11 - 15-pin plug for connecting the trailer
Maximum Transversal
Pin Code load cross-section Use
A mm2
1 1180 6 0.75 Left trailer indicator
2 1185 6 0.75 Right trailer indicator
3 2283 6 0.75 Rear foglight
4 0000 11 2.5 Ground
5 3339 6 0.75 Right rear marker/left trailer light
6 3330 6 0.75 Left rear marker/right trailer light
7 1179 6 0.75 Trailer brake light
8 2226 6 0.75 Tail-light
9 7790 11 2.5 ADR, terminal 30
10 6021 11 1.0 To ST64
11 8075 11 1.0 ST64 Pin 15
12 6642 11 1.0 Lifting axle signal for trailer in raised position. For bulkhead
coupling B Pin 19
13 0000 11 1.0 Ground
14 8081 11 1.0 To ST64 Pin 2
15 9021 11 1.0 To ST64
Remarks
Use connector ST64 described in paragraph 5.2.3 for connecting to terminals 10, 12, 14, 15.
Figure 5.14 shows truck connectors. The arrangement is similar and located behind the cab on tractors.
Figure 5.14
Table 5.12 - Component codes
ST14 Connector body component code:

98435333
Connector contact component code:
98457375 123249
ST14A Connector body component code:

500314817
500314823 (0.35-0.5 mm2)
500314824 (0.75-1.5 mm2)
123250
ST40X Connector body component code:

ST14B 41118303
41200695
123251

9843 5337
98457375 (0.35-0.5 mm2) 9845 5370 (0.75-1.5 mm2)
Gasket TN 486 1936
123766

9843 5338
98457375 (0.35-0.5 mm2) 9845 5370 (0.75-1.5 mm2)
Gasket TN 486 1936 123252

123253
9843 5337
98457375 (0.35-0.5 mm2) 9845 5370 (0.75-1.5 mm2)
Gasket TN 486 1936
Table 5.12 - (Continued)

9843 5337
98457375 (0.35-0.5 mm2) 9845 5370 (0.75-1.5 mm2)
123254
Gasket TN 486 1936
ST91-93 Connector body component code:
9843 5337

98457375 (0.35-0.5 mm2)
98455370 (0.75-1.5 mm2)
Gasket TN 486 1936
123255
Electrical circuit modifications
5.3 Electrical circuit modifications
CAN line wires and electric/electronic devices must not be modified.

! IVECO recommends not to change the other electrical circuits and wiring harnesses either.
Any modifications on the system will reduce quality and safety characteristics.
Bodybuilders must use genuine IVECO spare parts if changes to the electrical system are inevitable.
IVECO cannot be liable for system malfunctioning following the instructions contained in this chapter.
5.3.1 Introduction
The instructions provided by IVECO in paragraph 2.1.1 also refer to Multiplex system wiring harnesses.
IVECO connectors and the respective terminals cannot be modified. Avoid connecting and disconnecting the chassis ECU con-
nectors for more than three times to prevent damaging the gel which ensures tightness of the connections.
5.3.2 Wiring harness length
In Stralis, the MUX CAN line and the traditional electrical wires form a single wiring harness. Consequently, it is not possible
to replace only the CAN line or the electrical wiring where the electrical system is formed by both types of wires.
The wire length (CAN line + electrical wires) may not be correct when repositioning ECUs connected to the Multiplex system.
- excessive
- not sufficient
If the length is excessive, fold the wires without forming rings (this could cause undesired electromagnetic effects). Preferably use
figures of 8. The wire which connects the ECUs is very stiff. For this reason, it must be replaced when it cannot be folded.
Replace the wiring if the length is not sufficient. Use genuine IVECO spare parts (contact the IVECO service network).
The wire length depends on three factors: wheelbase, overhang and crossmember position. Select one of the variants in the table
for replacing the wiring if the modification involves a wheelbase/overhang which already exists in the IVECO range or, conversely,
choose the closest variant for the solution (the table only shows the currently produced wheelbase/overhang combinations).
In all cases, the CAN wiring itself cannot be changed. All modifications are expressly forbidden by IVECO.

Table 5.13
Vehicle Variant Wheelbase Overhang

1 4500 1803
2 5100 2388
4x2 truck
3 5700 2208
4 6300 2793
1 4200 2118
2 4500 2073
3 4800 2073
6x2P truck
4 5100 1803
5 5700 2433
6 6050 2658
1 3800 1488
6x4 trucks 2 4200 1848
3 4500 1982
1 3650 1048
4x2 tractors
2 3800 1048
6x2C tractors 2 3800 1048
This does not refer to modifications which do not involve the Multiplex wiring (CAN line + electrical wires). For example, when
extending the overhang without changing the position of the RFC, simply replace the electrical wires leading from the RFC to the
respective utilities.
IVECO recommends replacing traditional electrical wires with genuine components instead of modifying them.
Contact IVECO for particularly difficult cases. Send a diagram with the chassis dimensions and the new ECU positions.
5.3.3 Repositioning ECUs
IVECO recommends to avoid modifications which entails moving ECUs. Follow the instructions below if repositioning ECUs
is unavoidable:
- ECUs must be positioned on the chassis or in the cab and secured with a fastening similar to the original one (i.e. bracket). To
avoid malfunctions, the ECU in the chassis must not be turned (e.g. to avoid water ingress). Consequently, the original orientation
must be preserved;
- ECUs must not be fitted on the subframe;
- the cover must always be refitted;
- avoid subjecting ECUs to knocks from debris and stones from the road when travelling.

5.3.4 Disconnecting ECUs
! personnel can cause severe damage to on-board systems, effect driving safety and correct operation
of the vehicle and cause considerable damage which is not covered by warranty.
Follow the instructions below carefully before disconnecting an ECU:

- turn the ignition key to off, if it is inserted;
- switch off the additional heaters and wait for the end of the cooling down cycle (the warning light in the button will go out);
- open the TGC;
- isolate the battery by disconnecting the battery cables: disconnect the negative terminal first followed by the positive terminal;
- disconnect the ECU.

FMS
5.4 FMS
SVDI Vehicle Data Interface, (FMS interface) option 14569
Specific data is made available through the CAN line for vehicles fitted with option 14569. Information is available on:
- Engine speed
- Engine oil temperature
- Engine torque
- Speedometer data
- Current fuel consumption
- Current fuel reserve
- Display of axle load (if option 7306 present, display of axle load)
The exact composition of the data complies with the vehicle equipment (equipment with electronic control devices).
Data may be recalled in real time by installing a PC on board (option). The data format corresponds to FMS standard. The details
of this standard may be consulted on the internet at the address www.fms-standard.com.
Figure 5.15
MULTIPLEX SYSTEM ASSEMBLY (OPTION 6873)
117540
MTCO/DTCO. Tachograph - VCM. Vehicle Control Module - I.C. Cluster - B.C. Body Computer - DIAGNOSTIC
CONNECTOR. 30-pin diagnostic connector - EBS II. EBS II control unit - INTARDER. Intarder control unit -
ECAS. Air suspension control unit - EU II. Eurotronic II automatic transmission control unit - ACC. Adaptive Cruise
Control control unit - ECM. Engine management unit - UDS. Control unit for SCR - OBD supply module. 16 pin coupling for
OBD (on board diagnosis) - DDM. Driver Door Module - PDM. Passenger Door Module - BM. Bed Module - CC. Climate
Control - FFC. Front Frame Computer - RFC. Rear Frame Computer - HWH. Water heater - AAH. Air heater - CM. Cabin
Module - SWI. Steering Wheel Interface - EM (Expansion Module) - Radio. Radio - FMS. FMS (Fire Wall) connector -
P.C. Personal Computer
FMS
The following analyses may be carried out for subsequent processing of the data on a PC:
- checking of vehicle service data (trip duration, road sections, fuel consumption and speed)
- engine service data (rpm, load conditions)
- estimated oil consumption
- data for analysing brake use by the driver
- breakdown of road sections travelled, speed, breaks in the trip and resumption of trip.
To call up the data through a VDI interface, the onboard PC must be connected to connector ST40.
CAN connection between VDI interface and PC
Figure 5.16
123258
Pin for connector PN 41200695
Table 5.14 - Characteristics of the CAN line
Physical level Unshielded twisted pair cable compliant with ISO 11898 (SAE J1929/11).
Termination of internal bus to cable with 120 Ω resistor.
Data link level CAN 2.0B, 250 Kbit/sec. Format identifier and multi-packet message management compliant with SAE
J1929/21.
Application level Messages and parameters compliant with SAE J1939/71
The body builder is responsible for installation of the on-board PC, wiring for the ST40, hardware and software for subsequent
processing of data.
The information that may be called up via the VDI interface contains an ”FMS Standard Interface” message and identifies the version
that is supported by the VDI interface installed.
This message is not present if an interface that does not yet support the FMS standard is installed. The vehicle-related data quoted
in this paragraph are nevertheless still available in this case.
FMS
Electrical System: Modifications and Drawing---Off Power
5.5 Electrical System: Modifications and Drawing-Off Power
The vehicles operate on a 24v electric system for normal requirements and the chassis is an earth return. This acts as a current
return wire between relevant components, such as battery and alternator. All component negative terminals are connected through
the chassis in the absence of an insulated return wire.
Installation of auxiliary equipment or circuits added by the bodybuilder must take into account the instructions given below. Depending
on the complexity of the modification, suitable documentation (e.g. electrical diagram) must be provided for inclusion with that relating
to the vehicle.
Use colours and/or codes for wires and connectors equal to those used on the original vehicle makes the installation more consistent
and facilitates repair work.
NOTE For greater details on the vehicle’s electrical system, see the specific Workshop Manual, publication
no. 603.93.521 (Stralis AT/AD) - publication no. 603.93.531 (Stralis AS).
This manual is available at the IVECO Service network and can be requested from the relevant De-
partments of the IVECO Sales Organisation.
Precautions
The vehicles are equipped with sophisticated electrical/electronic systems controlling their operation.
Work on the system (e.g. removing wiring harness, making additional circuits, replacing equipment, changing fuses, etc.) that is not
done in conformity with IVECO instructions or is carried out by unskilled personnel can severely damage the systems (control units,
wiring, sensors, etc.), jeopardizing safety and operation of the vehicle besides causing significant damage (e.g. short-circuiting with
the risk of fire and destruction of the vehicle) that is not covered by warranty.
It is absolutely prohibited to make any changes or connections to the line linking the ECU’s (CAN line), which cannot be tampered
with, under any circumstances. Any fault diagnosis or maintenance work can only be done by authorized personnel with IVECO
approved equipment.
Always disconnect the batteries before commencing any work on the electrical system. First disconnect the negative and then the
positive power cable.
Use fuses with the required capacity for their specific function. Never use fuses of higher capacity. Change them only after eliminating
the problem with keys and ancilliaries disconnected.
Restore the original conditions of the wiring (routing, guards, and binding, preventing the cable at all costs from coming into contact
with metal surfaces of the structure that may impair its integrity).
During work on the chassis frame, to safeguard the electrical system, disconnect the relevant components and the earth connections,
follow the guides given in points 2.1.1 and 2.3.4.
Electrical System: Modifications and Drawing-Off Power

Never disconnect the connectors from the control units when the engine is running or when the control units are powered.
Never power components interlocked by electronic modules with the rated voltage of the vehicle through wander cables.
Control units equipped with metal sheathes have to be earthed through a screw or bolt unless otherwise specified.
When fitting additional equipment, where necessary, diodes must be fitted to provide protection against any induction current peaks.
The earth signal originating from analogue sensors must only be wired to a specific receiver. Additional earth connections could
result in false output signals being emitted from these sensors.
The wiring looms for the electronic components with low intensity signals must be arranged in parallel to the metal datum plane
i.e. it must adhere to the chassis/cab structure in order to reduce the parasite capacity. It should be spaced from additional wiring
looms as far as possible.
Additional equipment should be connected to the system earth with the utmost care (see point 2.1.1). The relative wiring must
not be fitted alongside the existing electronic circuits in order to avoid electromagnetic interference.
The wiring of the electronic systems (length, conductor type, arrangement, clamping, connecting shield braids etc.) must follow the
original IVECO standards. Carefully reset the original system after carrying out any work.
5.5.2 Electromagnetic compatibility
We recommend that electrical, electro-mechanical and electronic devices which comply with the following immunity require-
ments for electromagnetic emissions, both irradiated and conducted are used.
The level of electromagnetic immunity of the electronic devices equipping the vehicle, at a distance of 1 metre from the transmitting
aerial must be:
- 50V/m immunity for devices performing secondary functions (not impacting on direct vehicle control), for frequencies varying
from 20 MHz to 2 GHz.
- 100V/m immunity for devices performing main functions (not impacting on direct vehicle control), for frequencies varying from
20 MHz to 2 GHz.
The maximum admissible variation in transient voltage for units powered with 24 V is +80V, as measured at the terminals of the
artificial network (L.I.S.N.) during bench tests; otherwise, if the measurements are made on the vehicle, the variation must be deter-
mined at the most accessible point in the proximity of the device generating the disturbance.
NOTE The 24 V supplied devices:

- must be free from immune from negative noises, such as -600V spikes, positive +100V spikes,
+/-200V burst.
- they must operate correctly during voltage lowering phases to 8V for 40 mS and to 0V for 2 mS.
- moreover, they must resist the load dump phenomena up to 58V.
Max levels measured on bench for radiated and driven emissions generated by 24V devices are shown in Table 5.15.

Table 5.15
Frequency range and limits acceptable by noise in dBuV/m

Type of Type of 68-87 Unit of
Type of Type of 76-108
transdu disturb MHzm 820- measu
emission detector 150KHZ 530KHZ 5.9MHZ 30 -54 MHzbro 142-175 380-512
cer ance obile 960 re
300KHZ 2 MHZ 6.2MHZ MHZ adcast MHZ MHZ
services MHZ
only
only
radiated Aerial at Broad- Nearly
63 54 35 35 24 24 24 31 37
a dis- band peak
radiated t
tance off Broad- Peak
1 metre 76 67 48 48 37 37 37 44 50 dBuV/m
band
radiated Narrow- Peak
41 34 34 34 24 30 24 31 37
band
conduc- LISN Broad- Nearly
80 66 52 52 36 36
ted d 50 band peak
conduc- ohm/
h /5 Broad- Peak Not ap-
mH / 93 79 65 65 49 49 dBuV
ted band p
plicable
0, 1 mF
conduc- Narrow- Peak
70 50 45 40 30 36
ted band
Use electrical/electronic equipment in compliance with the EC Directives on electromagnetic compability, i.e use suitable compo-
nents for vehicle applications ”e..” marked (the EC marking is not sufficient). If in any doubt, call the IVECO Service Network.
Fine below an example of brand as required by the current European directive 2004/104EC applicable for electromagnetic compati-
bility in the automotive sector:
Figure 5.17
114476
a ≥ 6 mm
If in any doubt, call the IVECO Service Network.

These levels are granted only if the system comes from ”IVECO Spare Parts” or it has been certified as per ISO, CISPR, VDE interna-
tional regulations.
In case of systems which use the primary or secondary civil electric network (220V AC) as a supply source, the relevant characteristics
have to comply with the IEC regulations.
Two-way radio systems
The most common applications include:

- amateur two-way radio equipment for CB and 2 metre bands.
- two-way radio equipment for mobile phones.
- GPS satellite reception and navigation equipment.

The selection of the aerial to be installed is very important to ensure max performance to receiver and transmitter equipment.
It shall be of very good quality and installed with utmost care, even the mount position is of essential importance, as it determines
the aerial efficiency, therefore its transmission range.
Therefore, the ROS (Stationary Wave Ratio), gain and generated electromagnetic field characteristics must be ensured within prede-
fined limits, while impedance, efficient height, efficiency, orientability parameters are contained in manufacturer’s technical card.
The installation of 2m amateur CB sets, mobile phones (GSM) and satellite navigation systems (GPS) must use the power system
already present on the vehicle. The connection is made directly to terminal 30 of connector ST40 (and 15, where necessary).
Such devices must be legally type-approved and fixed (not portable). The use of two-way radio sets that are not type approved
or the application of extra amplifiers could seriously impair the efficient operation of the electric/electronic devices normally fitted
to the vehicle, to the detriment of vehicle and/or driver safety.
Amateur equipment for CB and 2m band
The installation of C.B. equipment (27 MHz), 1 m (144 MHz) shall require use of the supply system already installed on vehicle, with
connection to terminal 30 of ST40 connector.
These units must be type-approved according to the applicable legal requirements and must be of the fixed type (non portable)
type. The use of non type-approved receiver-transmitter units or supplementary amplifiers might affect the correct operation of
standard on-board electrical/electronic devices, with adverse effects on vehicle and/or driver safety.
The antenna must be installed outside the vehicle, possibly on a large metallic base as vertically as possible with the connection wire
leading downwards. Follow the instructions and the manufacturer’s warnings for assembly (see Figure 5.18).
• The ROS value must be as close as possible to the unit, the recommended value is 1.5 while max acceptable value must never
be greater than 2.
• The AERIAL GAIN values must be as high as possible and ensure sufficient spatial uniformity, normally with deviations from the
average value in the order of 1.5dB in the typical CB radio band (26.965-27.405 MHz).
• The IRRADIATED FIELD IN CABIN value must be as low as possible , < 1V/m is recommended as a quality target. In any
case, limits set by the applicable European legislations must never be exceeded.
• For this reason, the aerial must always be placed out of cabin.
In order to determine the good operation of radio-cable-aerial system and to check whether aerial is properly adjusted, we recom-
mend that following indications be followed:
1) If ROS is greater on low channels than on high channels, the aerial should be extended
2) If ROS is greater on higher channels than on low channels, the aerial should be shortened
After aerial adjustment, it is recommended to check ROS value again on al channels.
Installation at roof center is to be considered the best one as the ground plane is proportional in all directions, while mount on a
side or on any other vehicle part makes the ground plane proportional to its mass.
Cables involved in the installations should be connected and positioned taking care to:
- Use a top-quality, low-loss coaxial antenna cable with the same impedance as the transmitter and the antenna (see Figure 5.19).
- The coaxial cable run must be at a suitable distance (minimum 50 mm) from pre-existing wiring (TV, radio, telephone, amplifiers
and other electronic devices) to prevent interference and malfunctioning. Ensure the minimum distance from the metallic struc-
ture of the cab. Cable installation on the left or right-hand side is preferable.
- Clean the lower part of the hole made in the body for installing the antenna in fixed position so that the antenna support is
perfectly connected to the vehicle earth.
- The coaxial cable connecting the antenna to the radio must be fitted with the utmost care. Avoid curves or bends which can
pinch or distort the cable. Avoid tangling. Shorten the wire as much as possible.
Remember that any imperfections in the coaxial cable will cause severe interference for the radio transmitter.

- Use existing holes for routing the cable. Take all the necessary precautions for protecting the body if additional hole have to
be drilled (use anti-rust paint, sheath, etc.).
- Ensure a good connection with the vehicle earth both at the base of the antenna and at the device fixing to ensure maximum
power transfer.
Radio transmitters are typically fitted on the dashboard in the gear lever area or in the header rail above the driver (see Figure 5.20).
If the equipment uses a 12v power supply, a suitable 24-12V DC/DC converter will have to be fitted (if not already provided). The
power cables for the converter must be as short as possible with no coils and maintaining the minimum distance from the reference
plane.
Figure 5.18
98915
1. Antenna support - 2. Gasket (P/N for spares 244614) - 3. Fixed joint cover (P/N for spares 217522) - 4. Fixing screw
M6x8.5 (torque to 2 Nm) - 5. Antenna (spare P/N for complete rod 675120) - 6. Roof - 7. Antenna extension lead
Figure 5.19
99349
1. Antenna connector - 2. Ground wire - 3. Insulator - 4. Signal wire - 5. Capacitor (100pF) - 6. Cable RG 58 (characteristic
impedance = 50 Ω) - 7. Clamp - 8. Protective cap - 9. Connector (N.C. SO - 239) transceiver side - 10. Test executed sticker
- 11. The 100pF capacitor must be soldered on the lower pin and crimped to the ground braid - 12. The lower pin must be
soldered to the core conductor of the cable - 13. Nut

Figure 5.20
98915
1. Location of the CB transceiver unit (City Band)
Two-way systems for GSM/PCS/UMTS mobile phones
Cellular telephone systems must be installed using the power system provided in the vehicle. Connect to terminal 30 via a supple-
mentary fuse.
The devices must be legally type-approved and fixed (not portable). Install the transmitting part in a flat, dry area separate from the
electronic components of the vehicle, away from humidity and vibrations.
be greater than 2.
• The AERIAL GAIN values must be as high as possible and ensure sufficient space uniformity, featured by 1,5 dB deviations as
to average value in 870-960 MHz band and 2dB in the 1710-1880 MHz band.
• The IRRADIATED FIELD IN CABIN value must be as low as possible , < 1V/m is recommended as a quality target. In any
case, limits set by the applicable European legislations must never be exceeded.
• For this reason, the aerial must always be placed out of cabin, possibly on a metallic base with a large surface, installed as vertical
as possible, with connection cable turned downward, in compliance with Manufacturer’s installation instructions and warnings.
The antenna must be installed outside the vehicle, possibly on a large metallic base as vertically as possible with the connection cable
facing down. Follow the instructions and the manufacturer’s warnings for assembly.
The ideal location of the antenna is on the front of the cab roof at a distance no less than 30 cm from other antennas.

Follow the precautions below when connecting and arranging the wires:
- Use a top quality cable particularly as concerned to the protective shielding.
- The cable route must be at a suitable distance (minimum 50 mm) from pre-existing wiring. Ensure the minimum distance from
the metallic structure of the cab. Avoid excessively pulling or pinching the cable. Installation on the left or right-hand side is prefer-
able.
- Never shorten or extend the coaxial antenna cable.
- Use existing holes for routing the cable. Take all the necessary precautions for protecting the body if additional hole have to
- Ensure a good connection with the vehicle earth both on the base of the antenna and at the device fixing to ensure maximum
power transfer.
Cellular telephones are typically fitted on the dashboard in gear lever area or in the header rail above the driver.
plane.
GPS antenna cable and navigation system installation

Correct and careful assembly of GPS antennas in the vehicle is extremely important for correct operation and maximum perform-
ance.
The antennas should if possible be fitted in a concealed position where they cannot be seen.
Arranging the GPS antenna is a delicate matter. The power of the signal received from the satellite is very weak (approximately
136dBm), so any obstacle can effect quality and performance of the receiver.
be greater than 2 in the GPS frequency range (1575,42 +1,023 MHz).
• The AERIAL GAIN values must be as high as possible and ensure sufficient space uniformity, featured by 1,5 dB deviations as
to average value in 1575,41±1,023 MHz band.
The GPS antenna must be installed in a position ensuring maximum visibility of the sky.
The minimum angle of visibility must be 90°. Sky visibility must not be obscured by objects or metallic structures. The installation
position must be horizontal.
The ideal location for the GPS antenna is under the plastic dashboard in the middle and at the base of the vehicle windscreen.
Do not install the antenna under any type of metallic structure in the cab.
Position the GPS antenna at a distance which is not less than 30 cm from another antenna.
Follow the precautions below when connecting and arranging the wires:
- Use a top quality cable particularly concerning the protective shielding.
- The wire course must be at a suitable distance (minimum 50 mm) from pre-existing wiring. Ensure the minimum distance from
the metallic structure of the cab. Avoid excessively pulling or pinching the cable. Installation on the left or right-hand side is
preferable.
- Never shorted or extend the coaxial antenna cable.
- Use existing holes for routing the cable. Take all the necessary precautions for protecting the body if additional holes have to
- Ensure a good connection with the vehicle earth both on the base of the antenna and at the device fixing to ensure maximum
power transfer.
Navigation systems must be installed using the power system provided in the vehicle. Connect to terminal 30 via a supplementary
fuse.
The devices must be legally type-approved and fixed (not portable). Install the transmitting part in a flat, dry area separate from the
electronic components of the vehicle, away from humidity and vibrations.

plane.
When installing devices that could interact with other electronic systems, namely: Retarders, Extra
! heaters, Power take-offs, Air conditioners, Automatic transmissions, Telematics and Speed limiters
- contact IVECO to for efficient application.
NOTE For the operations which might cause interference with the basic system, it is necessary to carry out
diagnostic checks in order to make sure that the system has been properly fitted. These tests can be
carried out using on-board diagnostic ECUs (Electronic Control Units) or IVECO service.
IVECO reserves the right to void vehicle warranty if work is carried out in a way which does not com-
ply with IVECO directives.
5.5.3 Additional equipment
The vehicles system is designed to provide the necessary power to all the standard equipment. Each piece of equipment has
its own specific protection for its own function and the appropriate dimensions of the wires.
Fitting of additional equipment must include the provision of suitable protection and must not overload the vehicle’s system.
The earth connections of the additional devices must be made with a cable of an adequate size. It should be as short as possible
and permit movement of the apparatus in relation to the chassis of the vehicle.
If batteries of a greater capacity are used, due to the demand of the added loads, it is advisable to fit optional batteries or alternators
with a greater capacity.
In any case we recommend that the increase in the capacity of the batteries should not exceed 20 to 30% of the maximum values
provided as an optional extra by IVECO so as not to damage some components of the system (e.g. Starter motor). If greater capa-
cities are required, use additional batteries making the necessary arrangements for recharging as described below.
Additional Batteries and Alternators

Installing high power-consumption electric equipment (e.g. electrical motors frequently used or for a long time while the vehicle
engine is not running, such as tail lifts) or a great deal of additional electrical equipment, may require power which the vehicle’s stan-
dard system is unable to deliver. In such cases additional batteries of the appropriate capacity must be used.
Their insertion into the vehicle’s circuits must include a separate recharging system (see Figure 5.21) integrated with that of the
vehicle. In this case it is advisable to provide supplementary batteries with the same capacity as the batteries originally installed in
order to ensure correct recharging of all batteries.

Figure 5.21
Installing additional batteries
117409
1. Standard batteries - 2. Supplementary batteries - 3. Alternator with built-in regulator - 4. Starter motor -
5. Starter key - 6. Relays - 7. Front Frame Computer - 8. Instrument Cluster
Installing additional batteries involves checking that the alternator is of a sufficient capacity to recharge. If necessary, an alternator
with larger power or an additional one must be used. In this case connect up as shown in Figure 5.22.
When using electric motors which are activated only while the vehicle engine is running, instead of supplementary batteries, it could
be sufficient to use a larger power alternator or a supplementary one.
Such alternators have to be equipped with Zener diode rectifiers in order to avoid damaging the electrical/electronic systems already
fitted which might arise from accidental disconnection of the batteries.

Figure 5.22
Installing an additional alternator
TO BATTERIES
Terminal board
Green
connector PIN7
TO BATTERIES
117410
Auxiliary Electric Systems
Special care has to be taken when fitting refrigeration units that are driven by a second engine driven alternator.
These generators, according to their RPM, generate a voltage between 270 to 540 V in the wires that are routed to the cooling unit
on the vehicle.
The danger caused by possible electromagnetic interferences between wires from the above mentioned alternator being to close
to those already on the vehicle, can easily occur.
Such cases require highly insulated wires routed separately, yet not close to the standard wires of the vehicle.
The electromagnetic output levels previously mentioned have to be complied with for these units.
An error message will appear on the on-board panel in the event of standard alternator failure (e.g. low voltage, no signal).
An additional alternator cannot be connected and programmed to the MUX. Consequently, the MUX will not be capable of detect-
ing which alternator is not working correctly.

5.5.4 Taking current
From TGC (OPT)

For the Stralis, it is forbidden to connect additional electric systems directly on the battery positive pole. In fact, the positive pole
is engaged by the cables to the fuse-holder box placed on battery box side (for the ADR vehicles, the fuse-holder box, usually placed
on battery box side, is connected on the specific TGC pin).
The fusebox cannot be modified or moved.
Current can be taken from the specific TGC pin (TGC = general current relay, see Figure 5.23). Remove the plastic protection from
the free pin and connect the terminal directly to the threaded screw (positive pole). Fasten it with a suitable nut. The earth return
is via the chassis. For two or more connections, arrange a suitable shim between the terminals. Always use a suitable corrugated
tube to protect the wires. Always refit the plastic protection.
Read paragraph 5.3 on bodybuilders connectors before taking current in the cab. Current consumption
! must not exceed the maximum load value shown in the paragraph below.
5.5.5 General battery switch
It is normally located on battery box and operated manually. It is a two-pole switch disconnecting battery from underframe
letting tachograph (for law requirements), body computer, refrigerator, bed module and instrument cluster operate.
For special changes (e.g. fuel transport, dangerous substance transport) it might be necessary to use a safety switch fully insulating
batteries and alternator from the remaining system. Specific solutions for a given market are available on request.
NOTE the parallel connection to diverter output is permitted (max 100 A).
On chassis
Current cannot be taken from the terminal board under the hood. The terminals must neither be dis-
! connected nor modified.
personnel can cause severe damage to on-board systems, effect driving safety and correct operation
of the vehicle and cause considerable damage which is not covered by warranty.

Wire passage
The terminal board (component 8 in Figure 5.23) consists of a plate with five housings, four of which are occupied by connectors
(B, C, D and E) and one by a plate (A). The four connectors cannot be changed. The plate (component 1 in Figure 5.23) in housing
A is provided with two wire passages from the cab outwards and vice versa. A corrugated pipe (7) is fitted on the lower hole of
the plate (7) and can be used for passing the wires.
For bodybuilders requiring a second crossing point, disconnect the plate, remove the plug (2) from the plate, insert the specific
threaded fitting (3), pass the corrugated pipe containing the electrical wires through (diameter 13 mm) and fasten it to the plate
using the specific nut and the two sealed washers (4, 5, 6). Only use genuine IVECO components (contact IVECO Aftersales).
Figure 5.23
91468
Do not drill the plastic plug to pass the wires. Do not remove the plate. Genuine components ensure
! water and humidity tightness and must always be used. Operations which do not comply with the in-
structions specified by IVECO or made by non-qualified personnel can cause severe damage to on-
board systems and effect safety and reliability.

Maxifuse and Megafuse fuses

IVECO Shop offers a series of five fuseholder kits to protect high power draw power taps.
The positioning of the fuses (always as close as possible to the output terminal on the battery) must be decided by the bodybuilder
in accordance with the space available on the vehicle.
Figure 5.24
B
A C
91511
A. Maxifuse - B. Battery case - C. Megafuse
Table 5.16 - Maxifuse
Capacity Reference number of IVECO Body drawing number Cable cross-section

kit electrical accessories Fuseholder
KIT 40A 4104 0110 KZ 500317518 10 mm2
KIT 60A 4104 0111 KZ 500317518 10 mm2
The fuseholder (Part number 500317518) suitable for installation on a production line, must be secured to the chassis with a tighten-
ing torque of 2 ± 0.2 Nm.
Table 5.17 - Megafuse
Capacity Reference number of IVECO Body drawing number Cable cross-section

kit electrical accessories Fuseholder
KIT 100A 4104 0112 KZ 500315861 25 mm2
KIT 125A 4104 0113 KZ 500315861 35 mm2
KIT 150A 4104 0114 KZ 500315861 50 mm2
The current take-off from the battery positive terminal is to be considered as an alternative to a take-off from the battery isolator
switch when this latter is installed on the vehicle.

5.5.6 Additional circuits (fuses and conductor cross-section)
Additional circuits must be segregated and protected form the main vehicle circuit by means of fuses.
The cables utilised must be of a size that is suitable for the relative functions and must be well insulated. They must also be suitable
protected in sheaths (not PVC) or routed though flexible conduits in the case of a plurality of functions (we recommended the use
of polyamide type 6 plastic for flexible conduits) and they must be correctly installed in a place where they are protected from
impact and heat sources. Take care to avoid any chaffing with other components, particularly with live edges of the bodywork.
The transit of these cables through structural components (cross members, profiles, etc.) must be executed using suitable cable
glands or protections; firstly the cables must be secured separately with insulated cable clamps (e.g. made of nylon) at adequate
intervals (approx. 350 mm).
In case of external panels, use a specific sealant both on cable and on panel to avoid water, dust and fume ingress.
Establish suitable distance between electrical wiring harnesses and other components as follows:
- 10 mm from static components;
- 50 mm from moving components (minimum distance = 20 mm);
- 150 mm from components that generate heat (e.g. engine exhaust).
Wherever possible it is good practice to follow a different cable route for signal cables interfering at high absorbed intensity (e.g.
electric motors, solenoid valves) and signals that are susceptible to low absorbed intensities such as sensors, maintaining in any event
a position as close as possible to the metal structure of the vehicle in both cases.
Plug and terminal connections must be protected, resistant to weathering, and executed using components of the same type as
those utilised originally on the vehicle.
Use cables and fuses with the characteristics shown in the following table in accordance with the current draw:
Table 5.18
Max. continuous current 1) (A) Cable cross-section (mm2) Fuse capacity 2) (A)
0÷4 0.5 5
4÷8 1 10
8 ÷ 16 2.5 20
16 ÷ 25 4 30
25 ÷ 33 6 40
33 ÷ 40 10 50
40 ÷ 60 16 70
60 ÷ 80 25 100
80 ÷ 100 35 125
100 ÷ 140 50 150
1) For uses of more than 30 seconds.
2) Depending on the position and hence the temperature that may be reached in the housing, choose fuses that can be loaded to up to 70%- 80% of their maximum
capacity.
The fuse must be connected as close as possible to the current take-off point.
!
Precautions
- Avoid coupling with signal transmission cables (e.g. ABS), for which a preferential path has been defined for electromagnetic
requirements (EMI).It should be noted that when grouping several cables together, in order to compensate for the lower heat
dispersal capacity current intensity must be reduced with respect to the nominal value of a single cable.
- In vehicles subject to frequent engine starts, in the presence of power draws with limited engine running times (e.g. vehicles with
refrigerated bodies) periodic battery charges are required to maintain optimal efficiency.

5.5.7 Harness Modifications due to Changes to Wheelbase or Overhang
Should it be necessary to lengthen the wires on the chassis owing to the new dimensions of wheelbase and overhang, a watertight
junction box must be used which has the same characteristics as those used on the standard vehicle. The components used such
as wires, connectors, terminal blocks, conduits etc. must be of the same type as those used originally and be correctly fitted.
See the instructions given in paragraph 2.15.3 for electronic brake control device functionality.
5.5.8 Power Draw-off at a Voltage Different from that of the System
The vehicle electrical system is arranged for powering devices at 12V. A connection with voltage reducer (from 24V to 12V)
is fitted in the cab. Do not power devices directly by taking 12V from the battery.
The voltage reducer (supplied by IVECO) is arranged for a maximum current consumption of 20 A at
! 30°C measured in the device compartment in the header rail above the windscreen.
(Maximum consumption is 10A at 60°C).
Other devices with higher consumption must not be used.
5.5.9 Side Marker Lamps
Some national or EC regulations require that vehicle be equipped with side parking light, as a function of its overall length.
The Stralis range vehicles are equipped with specific terminals for the side light power supply connection.
Bodybuilders must fit the lights on the relevant structures and connect to the dedicated terminals (platform, box bodies, etc.).
The position of these terminals is shown below.
It is not possible to draw current from side parking lights.

!

Two special connectors are used to install side markers lights and are located behind the vehicle cab: ST77 on the right-hand side
and ST78 on the left-hand side (Figure 5.25).
Figure 5.25
117411
ST77. Terminal 4 poles per side marker lamp RH side - ST78. Terminal 4 poles per side marker lamp LH side
Connector on the vehicle Interface to use

9843 5343 Female connector 9843 5339 Male connector nº 1
9844 7233 Half bearing nº 1
9843 5370 Cable terminal nº 6
486 1936 Seal nº 6


STRALIS AS/AT/AD Euro 4/5 SPECIAL INSTRUCTIONS FOR -SCR- EXHAUST SYSTEMS 6-1
Index
SECTION 6
Special instructions for -SCR- exhaust system
Page
6.1 General specifications 6-3
6.2 The nitrogen oxide catalytic reduction principle. AdBlue 6-4
6.3 On-board instruments 6-7
6.4 Distribution of the ecological additive AdBlue 6-8
6.5 Specifications for installation and removal 6-9
6.5.1 Operations for positioning the AdBlue tank 6-9
6.5.2 Operations on AdBlue pipes and heating water 6-11
6.5.2.1 Instructions for lengthening and shortening the AdBlue ducts on the vehicle 6-15
6.5.3 Altering the supply module position 6-17
6.5.4 Operations on the dosing module 6-21
6.5.5 Operations on exhaust pipes 6-24
6.6 Wiring for positioning of SCR system components 6-25
6.7 OBD 1 - Stage 2 6-26
Index
6-2 SPECIAL INSTRUCTIONS FOR -SCR- EXHAUST SYSTEMS STRALIS AS/AT/AD Euro 4/5
Index
6666.6
6.1 General specifications
This chapter contains important information on the -SCR- exhaust systems fitted on the IVECO series (EuroCargo - Stralis -
Trakker).
In order to comply with Euro4 Euro5 standards, IVECO has chosen the SCR (selective catalyst reduction) system to reduce the
nitrogen oxide (NOx) emissions produced by exhaust gas.
SCR is an exhaust gas post-treatment system that uses a catalyzer which, by means of a chemical reaction, transforms NOx nitrogen
oxyde into nitrogen and water. This chemical reaction is produced by an additive called AdBlue (a solution of urea + water).
Figure 6.1
Coolant
AdBlue
117473
1. Pumping module - 2. Urea tank - 3. Catalyzer - 4. Dosing module
The nitrogen oxide catalytic reduction principle. AdBlue
6.2 The nitrogen oxide catalytic reduction principle. AdBlue
The additive is sent from a dedicated reservoir by means of supply module (1) to dosing module (3), which injects AdBlue into
the exhaust pipe.
The mixture thus obtained is then fed to the SCR catalyzer that transforms the NOx into nitrogen and water.
Post-treatment is based on a simple principle: the chemical reaction of ammonia NH3 with nitrogen oxides NO and NO2 produces
two harmless substances: water vapour H2O and nitrogen N2.
The whole system is managed by an electronic control unit.
Figure 6.2
114734
1. Pumping module - 2. Catalyzer - 3. Dosing module - 4. AdBlue reservoir

Main system components
Pump module
Figure 6.3
108128
1. Ad Blue return Pipe to the tank - 2. Ad Blue return Pipe from Dosing module - 3. Ad Blue solution outlet -
4. Ad Blue solution inlet - 5. Electrical connection - 6. DCU control unit - 7. Filter - 8. Pre-filter.
Dosing module
Figure 6.4
108128
1. Ad Blue inlet - 2. Electrical connection - 3. Ad Blue outlet

Its task is to meter the Ad Blue solution sent to the exhaust pipe upstream of catalyst.

Catalyzer
Figure 6.5
102301
Catalyst (1), equipped with sound-proofing material, replaces the exhaust silencer.
Inside the catalyst, the exhaust gas nitric oxides are, by reacting with ammonia, converted into free nitrogen and water vapour.
Temperature sensors (2 and 3) and nitric oxide detecting sensor (4) are fitted onto catalyst (1).
AdBlue reservoir
Figure 6.6
116720

On---board instruments
6.3 On-board instruments
The on board diagnostic system checks the tank level continuously and informs the driver on the current AdBlue quantity.
Figure 6.7
116719
On-board instruments
Distribution of the ecological additive AdBlue
6.4 Distribution of the ecological additive AdBlue
The ’AdBlue’ denomination is recognized internationally; it is an aqueous solution consisting of high purity urea according to
the DIN 70070 standard.
It is absolutely safe, non-toxic and non-flammable.
AdBlue manufacturers can assure the product direct distribution to the transporters with huge vehicle fleets, and the oil companies
are also planning to install AdBlue pumps close to diesel fuel pumps within a short time.
In this case it will also be available in tanks. A detailed list of sales outlets throughout Europe is available on the internet site: www.fin-
dadblue. com
Figure 6.8
114735
Figure 6.9 Figure 6.10
114736 114737
Distribution of the ecological additive AdBlue

Specifications for installation and removal
6.5 Specifications for installation and removal
The instructions that follow are intended for the AdBlue injection system of the Bosch DENOX2 type, within the SCR system.
If Bodybuilders make changes to the frame, the following procedures must be followed under all circumstances:
- disassembly: disconnect the hydraulic connectors first and then the electric connectors;
- assembly: connect the electric connectors first and then the hydraulic connectors.
Compliance with this assembly/disassembly procedure will ensure that AdBlue does not come into contact with the electric
connectors.
6.5.1 Operations for positioning the AdBlue tank
As regards the AdBlue tank, ensure that:

- the tank ventilation pipe is never closed;
- the reservoir must contain at least 5 l of AdBlue at the end of each operation to ensure the dosing module is cooled;
- after each operation, the tank does not contain more than 85% of AdBlue (corresponding to the max reading of the level sensor)
with respect to the tank total volume, so as to guarantee enough room for AdBlue to expand during freezing at temperatures
below -11 °C;
- the tank and the float are combined and cannot be modified. It is advisable to use a standard tank from the Stralis, Trakker or
Eurocargo construction series. 45, 60 and 120 litre tanks are available on the right side of the vehicle and 60 litre tanks on the
left. If a smaller tank is required, a 27 litre model is available in the Eurocargo construction series. In this case, note that a specific
data adaptation is required due to the shorter float;
- if specific-shaped tanks are available, these must be made out of polyethylene or stainless steel 1.4301, 1.43, in each case the
tank height must be respected.
- when fitting equipment onto the chassis, there is enough room for the AdBlue fill gun (1, Figure 6.11) to fit completely and
correctly into the tank filler.
Figure 6.11
116759

Removal and refitting of the AdBlue tank
Figure 6.12
102940
1. Cover - 2. Breather pipe - 3. AdBlue outlet pipes - 4. AdBlue heating fluid outlet pipes - 6. AdBlue inlet pipe - 7. AdBlue
heating fluid inlet pipe - 8. Level gauge
Remove cover (1) and remove the water/AdBlue pipes shown in the figure.
Figure 6.13
108613
Remove nut (4) and dismantle elastic strap (3) securing tank (2). Sling tank (2) with appropriate cable (5) and hook it to the
hoister. Remove tank from brackets (1).

Water/AdBlue connectors
Figure 6.14
114742
1. H2O infeed/outfeed connectors for AdBlue heater - 2. AdBlue infeed/outfeed connectors
The temperature and level sensors are connected to the DCU (Dosing Control Unit); the level sensor is specific to each type of
tank, therefore its dimensions cannot be modified.
6.5.2 Operations on AdBlue pipes and heating water
After turning off the engine, the outlet ducts (PL/UPL) and the inlet ducts (IL/UIL) must be drained to prevent the
! AdBlue freezing in the ducts and components if temperatures are low. The time that elapses is approximately 2 minute
and must not be interrupted by premature disconnection or the battery or disconnector. The process may clearly be
heard because the AdBlue pump keeps working even after the engine has been turned off.

As far as the pipes connecting reservoir, supply module and dosing module are concerned, ensure that:
- the connection pipes between the AdBlue reservoir and the supply module (delivery or inlet line or return or return line) must
be 5 m;
- the connection pipes between the supply module and the dosing module (delivery or pressure line and return or cooling line)
must be 3 m.
The pipes may only be modified using the ”Voss” fittings described in Table 6.1.
Table 6.1 - AdBlue

VOSS/IVECO
Teil -Nr:
Benennung Itemname Descrizione Description Descripción
Part -No:
Codice:
RACCORDO ANGOLO CONEXION EN ANGULO
Winkelkupplung SV241 ELBOW CONNECTOR RACCORD ANGLE SV241
5 4 62 07 00 00 SV241 5/16” VERSIONE SV241 5/16” VERSION
5/16” SV241 5/16” VERSION 5/16” VERSION GAUCHE,
SINISTRA; CON MLT IZQUIERDA; CON MLT
4128 3733 Ausführung links; LEFT; WITH MLT 8.8x1.4 AVEC MLT 8.8x1.4 PA0.2
8.8x1.4 PA0.2 8.8x1.4 PA0.2 LONGITUD
EZ 50-7499 mit MLT 8.8x1.4 PA 0.2 PA0.2 LENGTH 3m AND LONGUEUR 3 m ET
LUNGHEZZA 3m E 3 m Y BOQUILLA
114489 Länge 3m und Quetschhülse COMPRESSED SLEEVE BAGUE PRESSEE
BOCCOLA PRESSATA PRENSADA
ELBOW CONNECTOR RACCORDO ANGOLO RACCORD ANGLE SV241 CONEXION EN ANGULO
5 4 62 07 56 00 Winkelkupplung SV241
SV241 5/16” VERSION SV241 5/16” VERSIONE 5/16” VERSION DROITE, SV241 5/16” VERSION
5/16” Ausführung rechts; mit
4128 3734 RIGHT; WITH MLT 8.8x1.4 DESTRA; CON MLT 8.8x1.4 AVEC MLT 8.8x1.4 PA0.2 DERECHA; CON MLT
MLT 8.8x1.4 PA 0.2 Länge
EZ 50-7499 PA0.2 LENGTH 3m AND PA0.2 LUNGHEZZA 3m E LONGUEUR 3 m ET 8.8x1.4 PA0.2 LONGITUD 3
3m und Quetschhülse
114490 COMPRESSED SLEEVE BOCCOLA PRESSATA BAGUE PRESSEE m Y BOQUILLA PRENSADA
Geradekupplung SV241
5 4 62 08 89 00 CONNECTOR SV241 RACCORDO SV241 5/16”; RACCORD SV241 5/16”, CONEXION SV241 5/16”;
5/16”;
5/16”; WITH MLT 8.8x1.4 CON MLT 8.8x1.4 PA0.2 AVEC MLT 8.8x1.4 PA0.2 CON MLT 8.8x1.4 PA0.2
4128 3735 mit MLT 8.8x1.4 PA 0.2
PA0.2 LENGTH 3m AND LUNGHEZZA 3m E LONGUEUR 3 m ET LONGITUD 3 m Y
EZ 50-7499 Länge 3m
COMPRESSED SLEEVE BOCCOLA PRESSATA BAGUE PRESSEE BOQUILLA PRENSADA
114490 und Quetschhülse
RACCORDO ANGOLO CONEXION EN ANGULO
Winkelkupplung SV241 ELBOW CONNECTOR RACCORD ANGLE SV241
5 4 62 23 26 00 SV241 3/8” VERSIONE SV241 3/8” VERSION
3/8” Ausführung links; SV241 3/8” VERSION LEFT; 3/8” VERSION GAUCHE,
SINISTRA; CON MLT IZQUIERDA; CON MLT
4128 3736 mit MLT 8.8x1.4 PA 0.2 WITH MLT 8.8x1.4 PA0.2 AVEC MLT 8.8x1.4 PA0.2
8.8x1.4 PA0.2 8.8x1.4 PA0.2 LONGITUD
EZ 50-7499 Länge 3m LENGTH 3m AND LONGUEUR 3 m ET
LUNGHEZZA 3m E 3 m Y BOQUILLA
114492 und Quetschhülse COMPRESSED SLEEVE BAGUE PRESSEE
BOCCOLA PRESSATA PRENSADA
Winkelkupplung SV241 ELBOW CONNECTOR RACCORDO ANGOLO RACCORD ANGLE SV241 CONEXION EN ANGULO
5 4 62 23 49 00 3/8” Ausführung rechts; SV241 3/8” VERSION SV241 3/8” VERSIONE 3/8” VERSION DROITE, SV241 3/8” VERSION
4128 3737 mit MLT 8.8x1.4 PA 0.2 RIGHT; WITH MLT 8.8x1.4 DESTRA; CON MLT 8.8x1.4 AVEC MLT 8.8x1.4 PA0.2 DERECHA; CON MLT
EZ 50-7499 Länge 3m PA0.2 LENGTH 3m AND PA0.2 LUNGHEZZA 3m E LONGUEUR 3 m ET 8.8x1.4 PA0.2 LONGITUD 3
114493 und Quetschhülse COMPRESSED SLEEVE BOCCOLA PRESSATA BAGUE PRESSEE m Y BOQUILLA PRENSADA
Geradekupplung SV241
5 4 62 23 50 00 CONNECTOR SV241 3/8”; RACCORDO SV241 3/8”; RACCORD SV241 3/8”, CONEXION SV241 3/8”;
3/8”;
WITH MLT 8.8x1.4 PA0.2 CON MLT 8.8x1.4 PA0.2 AVEC MLT 8.8x1.4 PA0.2 CON MLT 8.8x1.4 PA0.2
4128 3738 mit MLT 8.8x1.4 PA 0.2
LENGTH 3m AND LUNGHEZZA 3m E LONGUEUR 3 m ET LONGITUD 3 m Y
COMPRESSED SLEEVE BOCCOLA PRESSATA BAGUE PRESSEE BOQUILLA PRENSADA
114494 und Quetschhülse
RACCORDO ANGOLO RACCORD ANGLE SV241 CONEXION EN ANGULO
Winkelstecker SV246 NG 8 ELBOW CONNECTOR
5 4 62 24 70 00 SV246 NG 8 ELEMENTO 8/16” ELEMENT SV246 NG 8 ELEMENTO
Öffnungselement weiss; SV246 NG 8 RELEASE CLIP
DI APERTURA BIANCO; D’OUVERTURE BLANC, DE APERTURA BLANCO;
4128 3739 mit MLT 8.8x1.4 PA 0.2 WHITE; WITH MLT 8.8x1.4
CON MLT 8.8x1.4 PA0.2 AVEC MLT 8.8x1.4 PA0.2 CON MLT 8.8x1.4 PA0.2
EZ 50-7499 Länge 3m PA0.2 LENGTH 3m AND
LUNGHEZZA 3m E LONGUEUR 3 m ET LONGITUD 3 m Y
114495 und Quetschhülse COMPRESSED SLEEVE
BOCCOLA PRESSATA BAGUE PRESSEE BOQUILLA PRENSADA
RACCORDO ANGOLO RACCORD ANGLE SV241 CONEXION EN ANGULO
Winkelstecker SV246 NG 8 ELBOW CONNECTOR
5 4 62 27 60 00 SV246 NG 8 ELEMENTO 8/16” ELEMENT SV246 NG 8 ELEMENTO
Öffnungselement schwarz; SV246 NG 8 RELEASE CLIP
DI APERTURA NERO; D’OUVERTURE NOIR, DE APERTURA NEGRO;
4128 370 mit MLT 8.8x1.4 PA 0.2 BLACK; WITH MLT 8.8x1.4
CON MLT 8.8x1.4 PA0.2 AVEC MLT 8.8x1.4 PA0.2 CON MLT 8.8x1.4 PA0.2
EZ 50-7499 Länge 3m PA0.2 LENGTH 3m AND
LUNGHEZZA 3m E LONGUEUR 3 m ET LONGITUD 3 m Y
114496 und Quetschhülse COMPRESSED SLEEVE
BOCCOLA PRESSATA BAGUE PRESSEE BOQUILLA PRENSADA
Set Verbinder MLT; SET CONNECTOR MLT; SET DI RACCORDO;
SET DE RACCORD ; JUEGO DE CONEXION;
1 Verbinder NW6 1 CONNECTOR NW6 1 RACCORDO NW6
1 RACCORD NVV6 1 RACOR NW6
2 1-Ohr Schellen 2 RETAINING CLIP 2 FASCETTA
5 4 66 12 06 49 2 COLLIER 2 ABRAZADERAS
1 Montageanleitung 1 ASSEMBLY 1 ISTRUZIONE DI
1 INSTRUCTION DE 1 INSTRUCCIONES DE
4128 3741 INSTRUCTION MONTAGGIO PRESTARE
ACHTUNG MONTAGE RESPECTER MONTAJE PRESTAR
EZ 50-7499 ATTENTION TAKE ATTENZIONE A
Montageanleitung LES INSTRUCTIONS DE ATENCION A LAS
114497 NOTICE OF ASSEMBLY L’ISTRUZIONE DI
9 1 77 00 02 20 MONTAGE 9 1 77 00 02 INSTRUCCIONES DE
INSTRUCTION 9 1 77 00 MONTAGGIO 9 1 77 00
beachten 20 MONTAJE 9 1 77 00 02 20
02 20 02 20
5 4 64 11 16 00 Rohr
TUBE MLT 8.8x1.4 PA0.2 TUBO MLT 8.8x1.4 PA0.2 TUBE MLT 8.8x1.4 PA0.2 TUBO MLT 8.8x1.4 PA0.2
4128 3742 MLT 8.8x1.4 PA0.2
LENGTH 10m LUNGHEZZA 10m LONGUEUR 10m LONGITUD 10 m
114498
RACCORDO PIASTRA DI RACCORD PLAQUE DE CONEXION CHAPA DE
5 4 62 35 74 00 Stecker Trennstelle; CONNECTOR SECTION
SEZIONAMENTO; CON SECTIONNEMENT, AVEC SEPARACION; CON MLT
mit MLT 8.8x1.4 PA 0.2 POINT; WITH MLT 8.8x1.4
4128 3743 MLT 8.8x1.4 PA0.2 MLT 8.8x1.4 PA0.2 8.8x1.4 PA0.2 LONGITUD
Länge 3m und PA0.2 LENGTH 3m AND
EZ 50-7499 LUNGHEZZA 3m E LONGUEUR 3 m ET 3 m Y BOQUILLA
Quetschhülse COMPRESSED SLEEVE
114500 BOCCOLA PRESSATA BAGUE PRESSEE PRENSADA
Kupplung RACCORDO PIASTRA DI RACCORD PLAQUE DE CONEXION CHAPA DE
5 4 62 35 75 00 CONNECTOR SECTION
Trennstelle; SEZIONAMENTO; CON SECTIONNEMENT, AVEC SEPARACION; CON MLT
POINT; WITH MLT 8.8x1.4
4128 3744 mit MLT 8.8x1.4 PA 0.2 MLT 8.8x1.4 PA0.2 MLT 8.8x1.4 PA0.2 8.8x1.4 PA0.2 LONGITUD
PA0.2 LENGTH 3m AND
EZ 50-7499 Länge 3m und LUNGHEZZA 3m E LONGUEUR 3 m ET 3 m Y BOQUILLA
COMPRESSED SLEEVE
114501 Quetschhülse BOCCOLA PRESSATA BAGUE PRESSEE PRENSADA

Table 6.1 - (cont.) Cooling water

VOSS/IVECO
Teil -Nr:
Part -No:
Codice:
5 4 62 28 42 00 Winkelstecker SV246 NG
SV246 NG 12 RELEASE SV246 NG 12 ELEMENTO NG 12 ELEMENT SV246 NG 12 ELEMENTO
12 Öffnungselement weiss;
4128 3745 EZ CLIP WHITE; WITH DI APERTURA BIANCO; D’OUVERTURE BLANC, DE APERTURA BLANCO;
mit Rohr Grilamicl 13x1.5
50-7499 GRILAMID TUBE 13x1.5 CON TUBO GRILAMID AVEC TUBE GRILAMID CON TUBO GRILAMID
Länge 3m
114502 LENGTH 3m 13x1.5 LUNGHEZZA 3m 13x1.5 LONGUEUR 3m 13x1.5 LONGITUD 3 m
5 4 62 29 49 00 Winkelstecker SV246 NG
SV246 NG 12 RELEASE SV246 NG 12 ELEMENTO NG 12 ELEMENT SV246 NG 12 ELEMENTO
12 Öffnungselement blau;
4128 3746 EZ CLIP BLUE; WITH TUBE DI APERTURA BLU; CON D’OUVERTURE BLEU, DE APERTURA AZUL;
mit Rohr Grilamid 13x1,5
50-7499 GRILAMID 13x1.5 LENGTH TUBO GRILAMID 13x1.5 AVEC TUBE GRILAMID CON TUBO GRILAMID
Länge 3m
114503 3m LUNGHEZZA 3m 13x1.5 LONGUEUR 3m 13x1.5 LONGITUD 3 m
0 0 26 11 50 00
4128 3747 EZ Verbinder NW 10 CONNECTOR NW 10 RACCORDO NW 10 RACCORD NW 10 CONEXION NW 10
50-7499
114504
5 4 64 19 08 00
Rohr GRILAMID 13x1.5 TUBE GRILAMID 13x1.5 TUBO GRILAMID 13x1.5 TUBE GRILAMID 13x1.5 TUBO GRILAMID 13x1.5
4128 3748 EZ Länge 10m LENGTH 10m LUNGHEZZA 10m LONGUEUR 10m LONGITUD 10 m
50-7499
114505
5 4 62 35 76 00 CONNECTOR SECTION RACCORDO PIASTRA DI RACCORD PLAQUE DE CONEXION CHAPA DE

Stecker Trennstelle; mit Rohr POINT; WITH TUBE SEZIONAMENTO; CON SECTIONNEMENT AVEC SEPARACION; CON TUBO
4128 3749 EZ Grilamid 13x1,5 Länge 3m GRILAMID 13x1.5 LENGTH TUBO GRILAMID 13x1,5 TUBE GRILAMID 13x1,5 GRILAMID 13x1,5
50-7499 3m LUNGHEZZA 3m LONGUEUR 3m LONGITUD 3 m
114506
5 4 62 35 77 00 Kupplung Trennstelle; mit CONNECTOR SECTION RACCORDO PIASTRA DI RACCORD PLAQUE DE CONEXION CHAPA DE
Rohr Grilamid 13x1,5 Länge POINT; WITH TUBE SEZIONAMENTO; CON SECTIONNEMENT AVEC SEPARACION; CON TUBO
4128 3750 EZ GRILAMID 13x1.5 LENGTH TUBO GRILAMID 13x1,5 TUBE GRILAMID 13x1,5 GRILAMID 13x1,5
50-7499 3m
3m LUNGHEZZA 3m LONGUEUR 3m LONGITUD 3 m
114507
Table 6.1 - (cont.) Corrugated pipe

VOSS/IVECO
Teil -Nr:
Part -No:
Codice:
5 4 66 11 37 00
CORRUGATED HOSE TUBO CORRUGATO TUBE ANNELE NW37 TUBO CORRUGADO
4128 3751 EZ Wellrohr NW37 Länge 3m
NW37 LENGTH 3m NW37 LUNGHEZZA 3m LONGUEUR 3m NW37 LONGITUD 3 m
50-7499
114479
5 4 66 12 10 00
50-7499
114480
5 4 66 12 09 00
50-7499
114481
Table 6.1 - (cont.) Breather pipe

VOSS/IVECO
Teil -Nr:
Part -No:
Codice:
5 4 66 09 65 00
4128 3757 EZ Verbinder NW 6 CONNECTOR NW 6 RACCORDO NW6 RACCORD NW6 CONEXION NW6
114511 50-7499
5 4 64 19 09 00
Rohr 6x1 PA12PHLY Länge TUBE 6x1 PA12PHLY TUBO 6x1 PA12PHLY TUBE 6x1 PA12PHLY TUBO 6x1 PA12PHLY
4128 3758 EZ 10m LENGTH 10m LUNGHEZZA 10m LONGUEUR 10m LONGITUD 10 m
50-7499
114512
5 4 66 10 21 00
4128 3759 EZ Verbinder NW 10 CONNECTOR NW 10 RACCORDO NW10 RACCORD NW10 CONEXION NW10
50-7499
114513
5 4 64 19 10 00
Rohr 10x1 PA12PHLY TUBE 10x1 PA12PHLY TUBO 10x1 PA12PHLY TUBE 10x1 PA12PHLY TUBO 10x1 PA12PHLY
4128 3760 EZ Länge 10m LENGTH 10m LUNGHEZZA 10m LONGUEUR 10m LONGITUD 10 m
50-7499
114478

Table 6.1 - (cont.) Components

VOSS/IVECO
Teil -Nr:
Part -No:
Codice:
5 0 99 11 64 00 CAPUCHON DE COBERTURA DE
PROTECTION CAP TANK CAPPA DI PROTEZIONE
4128 3761 EZ Schutzkappe Tank 0° PROTECTION RESERVOIR PROTECCION DEPOSITO
0° SERBATOIO 0°
50-7499 0° 0°
114477
5 0 99 11 71 00 CAPUCHON DE COBERTURA DE
PROTECTION CAP TANK CAPPA DI PROTEZIONE
4128 3762 EZ Schutzkappe Tank 90° PROTECTION RESERVOIR PROTECCION DEPOSITO
90° SERBATOIO 90°
50-7499 90° 90°
114488
5 4 66 09 30 00
CONVOLUTED RUBBER
4128 3763 EZ Faltenbalg SOFFIETTO SOUFFLET RESPIRADERO
GAITER
50-7499
114499
5 4 66 09 64 00 T-CONNECTOR FOR DISTRIBUTORE A T PER DISTRIBUIDOR EN T PARA

DISTRIBUTEUR EN T POUR
4128 3764 EZ T-Stück für Wellrohr NW37 CORRUGATED HOSE TUBO CORRUGATO TUBO CORRUGADO
TUBE ANNELE NW37
50-7499 NW37 NW37 NW37
114508
5 3 49 03 21 00 PIASTRA DI COPERTURA PLAQUE DE

COVERPLATE SECTION CHAPA DE COBERTURA
4128 3765 EZ Deckplatte Trennstelle PUNTO DI COUVERTURE POINT DE
POINT PUNTO DE SEPARACION
50-7499 SEZIONAMENTO SECTIONNEMENT
114509
5 3 49 03 20 49
BASE PLATE SECTION PIASTRA DI BASE PUNTO PLAQUE DE BASE POINT CHAPA DE BASE PUNTO
4128 3766 EZ Grundplatte Trennstelle
POINT DI SEZIONAMENTO DE SECTIONNEMENT DE SEPARACION
50-7499
114510
Table 6.1 - (cont.) Tools

VOSS/IVECO
Teil -Nr:
Part -No:
Codice:
5 9 94 52 14 00 ALICATES DE MONTAJE
Kunststoffrohr NYLON TUBE PINZA DI MONTAGGIO PINCE DE MONTAGE
Iveco: 99387101 PARA TUBO DE
Montagezange MOUNTING PLIERS PER TUBO PLASTICA POUR TUBE PLASTIQUE
50-7499 PLASTICO
114482
5 9 94 71 53 49
Spannbacken für Rohr MLT CLAMPING JAWS FOR MORSA PER TUBO MLT GRIFFE DE SERRAGE POUR MORDAZA PARA TUBO
Iveco: 99387102 8.8x1.4 TUBE MLT 8.8x1.4 8.8x1.4 TUBE MLT 8.8x1.4 MLT 8.8x1.4
50-7499
5 9 94 65 41 00 Spannbacken für Rohr CLAMPING JAWS FOR MORSA PER TUBO GRIFFE DE SERRAGE POUR MORDAZA PARA TUBO
Iveco: 99387103 GRILAMID 13x1.5 (08/ 010/ TUBE GRILAMID 13x1.5 GRILAMID 13x1.5 (08/ 010/ TUBE GRILAMID 13x1.5 GRILAMID 13x1.5 (08/ 010/
50-7499 012/ 013) (08/ 010/ 012/ 013) 012/ 013) (08/ 010/ 012/ 013) 012/ 013)
114484
5 9 94 71 55 00 Werkzeugeinsatz Aufnahme TOOLING INSERT COLLET INSERTO STAMPO EMPREINTE MOULE UTIL ESTAMPACION
für Verbinder NW6 FOR CONNECTOR NW 6 ALLOGIAMENTO PER LOGEMENT ALOJAMIENTO PARA
Iveco: 99387104 CONNETTORI NW6 CONNECTEURS NVV6 CONEXIONES NW6
114485 50-7499 (Harnstoff) (AD-BLUE)
(UREA) (UREE) (UREA)
INSERTO STAMPO EMPREINTE MOULE UTIL ESTAMPACION
5 9 94 69 16 49 Werkzeugeinsatz Aufnahme TOOLING INSERT COLLET ALLOGIAMENTO PER LOGEMENT ALOJAMIENTO PARA
Iveco: 99387105 für Verbinder NW10 FOR CONNECTOR NW CONNETTORI NW10 CONNECTEURS NW10 CONEXIONES NW10
50-7499 (Kühlwasser) 10 (COOLING WATER) (AQUA DI (EAU DE (AGUA DE
114486 RAFFREDDAMENTO) REFROIDISSEMENT) REFRIGERACION)
5 9 94 71 56 00 MANDRIN A MANDRIL PARA

Aufweitdorn für Rohr MLT WIDENING SPIKE FOR MANDRINO
Iveco: 99387106 DUDGEONNER MLT AVELLANAR TUBOS MLT
8.8x1.4 TUBE MLT 8.8x1.4 ALLARGATUBI MLT 8.8x1.4
50-7499 8.8x1.4 8.8x1.4
114487
Klemmzange für CLAMPING PLIERS FOR MORSETTO PER CLIP POUR COLLIER DE UTIL PARA
9 7 51 00 00 08
Einohrschelle CLIP RETAINER FASCETTA SERRAGE ABRAZADERAS
TRONCHESE PER TUBO IN TRICOISES POUR TUBE EN CORTADOR DE TUBO DE
5 9 94 84 72 00 Kunstoffrohr-Schneidezange NYLON TUBE SCISSORS
PLASTICA PLASTIQUE PLASTICO
Ersatzklinge für LAMA DI RICAMBIO PER LAME DE RECHANGE DE CUCHILLA DE RECAMBIO
SPARE BLADE FOR
5 9 94 84 74 00 Kunstoffrohr-Schneidezange TRONCHESE PER TUBO IN TRICOISES POUR TUBE EN PARA CORTADOR DE
NYLON TUBE SCISSORS
(2 Stück) PLASTICA PLASTIQUE TUBO DE PLASTICO
- When working on the pipes, it is compulsory to work in a completely dust-free environment to prevent dust reaching the injector.
- Restore all the pipe insulation (water and Urea pipes) to prevent freezing.

6.5.2.1 Instructions for lengthening and shortening the AdBlue ducts on the vehicle
1) Mark the delivery and returns ducts before separating them to ensure that they are correctly positioned during subsequent
assembly. The maximum permitted length for ducts must not exceed 5 m from the reservoir to the supply module and 3 m
from the supply module to the dosing module.
2) Cut the AdBlue duct (MLT Rehau - VOSS HWL 8.8 x 1.4 PA wall thickness 0.2 mm and 0.4 mm PA/PUR) with the appropriate
pipe cutting clippers in order to ensure an accurate cutting area. For reasons of space, it is advisable to divide the AdBlue delivery
and return ducts along the length of the line.
Figure 6.15
123261
3) The special band is pushed by the fitting toward the end of the pipe.
4) The pipe is inserted in the pipe jaws and secured by clips. The end of the duct should extend 4-5 mm from the clips. The tightening
force must be adjusted using adjustment screw (A) (the distance of the jaws without the pipe must be approximately 1-2 mm).
Figure 6.16
123262
5) Fit expanding pin (B) in the tool element and push the transport bar mechanically toward the pipe until the pin cone fits fully
into the pipe. Then pull the bar back and remove the expansion plug.

Figure 6.17
B
123263
6) The expanded side of the joint on the duct to be fitted must be moistened with water to above the O-Ring and fitted into the
tool insert. The connector must be pressed toward pipe by hand through the transport bar until the profile of the pipe expander
is centred within the inner diameter of the pipe.
7) Use the appropriate lever to push the connector into the pipe to the end of the expansion pin. It is advisable to exercise continu-
ous pressure while doing this.
8) Release the locking jaws, position the special bands up to 5+ 1 mm from the collar and press using the manual pliers (C.)

6.5.3 Altering the supply module position
On some body models or for some types of service, it is necessary for components of the AdBlue system such as the AdBlue
tank, the dosing module or the supply module to be fitted in another part of the vehicle.
When moving the AdBlue components, take particular care over the height differences between them. Relevant examples are shown
in the following figures.
Figure 6.18
117474
1. AdBlue reservoir - 2. Pumping module - 3. Dosing module - 4. Siphon compulsory

The supply module must be fitted on a fixed base. The preferred fitting position of the supply module is vertical with the attach-
ments facing down. A different position is possible within the measurements shown below. The fitting position on Stralis vehicles
corresponds to layout in version b. When connecting the AdBlue pipe to the DM, ensure that the pipe is fitted leading upwards
just before the DM (illustration below).
Figure 6.19
117474

If the position of the supply module (SM) is altered, a check must be carried out to ensure that the environmental temperature
corresponds
to that of the original installation. In case of doubt, it is advisable to re-check the temperatures.
The following abbreviations may be used in the description of the component position:
Figure 6.20
• AdBlue reservoir (T)
• Supply module(SM)
• Dosing module (DM)
• AdBlue delivery pipe (UIL)
• AdBlue pressurised pipes (UPL)
• AdBlue cooling pipes (UCL)
• A AdBlue return pipe (URL)
123265
1. Reservoir ventilation - 2. Residual air - 3. Return line - 4. Temperature sensor - 5. AdBlue level sensor -
6. Delivery line - 7. Reservoir minimum level - 8. Reservoir heater.
The AdBlue reservoir is lower than the supply module(SM):
The maximum intake height corresponds to the difference between reference point (6) = lower edge of the supply module
and the lower edge of the intake duct (5). The intake height must not exceed 1 m.
Figure 6.21
123266
1. Supply module (SM) - 2. Supply line - 3. AdBlue reservoir - 4. AdBlue minimum level - 5. Intake duct lower edge -
6. Lower edge of supply module.

The AdBlue reservoir is higher than the supply module(SM):

The maximum intake height corresponds to the difference between the lower edge of intake pipe (5) and the highest point of
intake duct (2). This height must not exceed 1 m.
Figure 6.22
123267
1. AdBlue reservoir - 2. Upper edge of intake pipe - 3. Level of AdBlue in reservoir - 4. Supply module - 5. Lower edge of
intake pipe.
Dosing module (DM) is lower than supply module (SM):
The upper edge of delivery duct (2) must be located above reference point (8).
123268
1. Supply module - 2. Upper edge of intake duct - 3. AdBlue reservoir - 4. Level of AdBlue in reservoir - 5. AdBlue minimum
level - 6. Siphon - 7. Dosing module (DM) - 8. Lower edge of supply module.

The AdBlue reservoir is higher than the supply module (SM):

The upper edge of delivery duct (1) must be located above reference point (5).
Figure 6.23
123269
1. Pressurised pipe - 2 AdBlue level - 3. AdBlue reservoir - 4. Minimum level of AdBlue - 5. Lower edge of supply module.

6.5.4 Operations on the dosing module
When the dosing module requires repositioning, note some important precautions.
Figure 6.24
114743
STRUCTURE OF THE MEASURING MODULE

1. Heatshield - 2. Temperature sensor - 3. Valve holder - 4. AdBlue connectors - 5. Dosing valve - 6. Cooling adapter -
7. Insulation
Figure 6.25
A 158 mm " 117475
- Inside the exhaust gas pipe is placed a diffuser (1) therefore the pipe interested cannot be modified.

Orientation of dosing module (DM) in the exhaust pipe:

When positioning the DM, a distinction is drawn between the positioning rotation angle in the exhaust pipe and the exhaust pipe
installation angle (see following figure).
Figure 6.26
Exhaust pipe installation angle
Angle of rotation of DM in exhaust pipe 123270
Orientation of dosing module (DM) in relation to angle

of rotation in exhaust pipe:
To prevent operating errors and damage to the DM, the
following positions must be respected during installa-
tion:
- 315˚ - 45˚ (A)
The increasing heat in the exhaust pipe may damage
the DM or cause it to malfunction. In this case, a heat
shield must be installed under all circumstances.
- 90˚ - 270˚ (D)
The AdBlue fluid contained in the dosing module. In
If temperatures are very low, this may freeze and
damage the module.
- 45˚ - 90˚ and from 270˚ to 315˚ (C - E)
In this position installation is possible, a minimum
quantity of AdBlue remains in the module. 123271
- 60˚ - 70˚ (B)

This is the idea position for installing the DM and
must be absolutely preferred if conditions permit.
Exhaust gas pipe installation angle:
The installation angle must be between +45˚ and -90˚.

Installation of the form of dosing in relationship to the catalyst SCR:
Figure 6.27
Mixer pipe length
Silencer
Example of DM installation:
- exhaust pipe angle of inclina-
tion 45˚.
SCR catalytic
- rotation of DM +90˚
converter
The exhaust pipe input into the SCR
catalytic converter must be as low as
possible
123272
NOTE The exhaust pipe input into the SCR catalytic converter must be located as low as possible. If the cata-
lytic converter is turned so that the exhaust pipe input is located in the upper part, there is a danger
of the hot exhaust gases going back into the dosing module if the engine stalls, with a consequent risk
of damage.
Distance of the DM from the SCR catalytic converter:

On IVECO Cursor engines, the distance of the DM from the SCR catalytic
converter must not be less than 1200 mm. Lower distances must be checked and
authorised in each individual case.
In some conversions, it may be necessary to locate the SCR catalytic converter
in a new position on the vehicle. Taking into consideration the above conditions,
the exhaust gas (start or mixer pipe to the inlet of the SCR plug) may be extended
up to 3 m.
A further extension of the exhaust gas pipe makes it absolutely necessary to insu-
late the pipe to avoid excessive heat dispersion with a possible consequent mal-
function of the SCR system SCR.
An overall exhaust pipe length of 6 m must not be exceeded under any circum-
stances.
The distance ( X ) between the DM and the next bend depends on the angle and
the following distances must be complied with:
- 30˚ bend > distance 150 mm
- 45 bend > distance 200 mm
- 90˚ bend > distance 300 mm
If an adaptation should be necessary due to the tubomixer, the following require-
ments must be observed:
To prevent the formation of sediment in the exhaust pipe behind the mixer due 123273
to sharp edges or welds, a connection to the mixer must be created at least 10

mm before the end of its internal duct.

NOTE If the dosing module is moved, the pipes and electrical wiring must be modified.
6.5.5 Operations on exhaust pipes
NOTE The exhaust pipe layout cannot be changed without the approval of IVECO.
The exhaust pipe can be modified paying attention to the following warnings:
- Type approved (homologated) counter-pressures must be respected when determining the exhaust pipe route. Form bends
with angles greater than 90˚ and radius of curvature greater than 2.5 times the pipe diameter. Keep the exhaust pipe far enough
away from rubber or plastic parts and fit heat shields if necessary.
- It is not permitted to use pipes with diameters, thicknesses and materials other than those used for the original equipment.
- It is permitted to use hoses with limited lengths.
- In some conversions, it may be necessary to locate the SCR catalytic converter in a new position on the vehicle. Taking into
consideration the above conditions, exhaust gas pipe (start of mixer pipe to the SCR plug intake) may be extended up to 3 m.
- A further extension of the exhaust gas pipe makes it absolutely necessary to insulate the pipe to avoid excessive heat dispersion
with a possible consequent malfunction of the SCR system.
An overall exhaust pipe length of 6 m must not be exceeded under any circumstances.
Electrical wiring:
- It is only possible to lengthen cables for the temperature sensors.
- It is not possible to alter the length of the Nox sensor cable.

Wiring for positioning of SCR system components
6.6 Wiring for positioning of SCR system components
If the SCR system components are moved (e.g. total or partial movement of the rails and lengthening of wheelbase), Iveco makes
available replacement material and wiring to ensure final product quality.
Table 6.2 - Replacement of cables for repositioning of SCR system components

Basic pump module cable
(for movement of the SCR Supply Module within the frame, dis. n˚ 41244952
on the left side).
2 m pump module movement cable.
(To be added to the basic cable
cable, in longer wheelbases and in dis n˚ 41244954
dis.
cases where the wheelbase is lengthened)
P/N 4 m pump module movement cable.
(To be added to the basic cable, in longer wheelbases and in dis. n˚ 41244955
cases where the wheelbase is lengthened)
Electrical cable for heated pre-filter
(For movement of the heated prefilter to the left side of the dis. n˚ 41245115
frame
Fuel tank electrical cable
dis. n˚ 41245116
(For movement of the tank to the left side of the frame)
Wiring for positioning of SCR system components

OBD 1 --- Stage 2
6.7 OBD 1 - Stage 2
The Emissions Directive introduced on 1 October 2007 obliges industrial vehicle manufacturers to reduce engine performance
if Nox emissions do not meet requirements laid down by the regulation during use of the vehicle.
When driving with the AdBlue reservoir empty (AdBlue level below the minimum operating level for the dosing unit) or with other
causes that do not permit the vehicle to respect the NOx emission levels specified in the regulations, the engine
will undergo a reduction in performance (derating) indicated in advance by the yellow OBD warning light coming on the instrument
panel (see Figure 6.28).
This drop in performance is activated on the first occasion that vehicle speed is reduced to zero and persists until the emission control
devices are restored to normal operating conditions, allowing the vehicle to comply with an NOx emissions again (e.g.: If the AdBlue
reservoir is empty, it should simply be refilled) and has no effect on vehicle reliability.
Note also that the on-board control unit is legally bound to record such events so that they may be made available during any future
police checks.
Figure 6.28
CONDITION CONSEQUENCE SYMBOL

AdBlue remains approximately 10%
Driver notified (warning light flashes) YELLOW
below the tank capacity
warning
i light
li ht
Non-compliance with Nox values estab- AdBlue warning light comes on with con-
lished in standards: tinuous light, reduction in engine per-
• AdBlue tank empty formance and fault code stored for 400
• Dosing stopped days or 9600 hours of engine operation
• Any deviation greater than 50% of
average AdBlue consumption
125201
OBD 1 - Stage 2

IVECO Stralis Euro 4 - 5 Bodybuilder Instructions

Uploaded by

Copyright:

Available Formats

IVECO Stralis Euro 4 - 5 Bodybuilder Instructions

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

IVECO Stralis Euro 4 - 5 Bodybuilder Instructions

Uploaded by

Copyright:

Available Formats

STRALIS AS/AT/AD

Publication Edited by:

Section Description Page Revision date

2 Frame Paragraph 2.16 moved to chapter 5 January 2008

3 Structures 3-34: paragraph added 3.5.4.3 January 2008

4 Power take-off 4-17: Control unit added January 2008

5 Electronic subsystems 5-4: Cab Module (CM) January 2008

5 Electronic subsystems 5-8,5-9: connectors ST14A e ST14B January 2008

5 Electronic subsystems 5-40: note added to paragraph 5.4.8 January 2008

(*) Specific parts only for OBD1 Phase 2.

Print 603.93.721 Base - January 2008

Base - January 2008 Print 603.93.721

Danger of serious damage to the vehicle

NOTE Indicates additional information.

Print 603.93.721 Base - January 2008

Print Basic edition -

Base - January 2008 Print 603.93.721

Print 603.93.721 Base - January 2008

Base - January 2008 Print 603.93.721

1.1 Aim of bodybuilders instructions 1-3

1.2 IVECO “no objection” for changes and fittings 1-3

1.3 Liabilities 1-4

1.4 Guarantees 1-4

1.5 Request for a “no objection” 1-4

1.6 IVECO technical documents available by means of computer 1-5

1.7 Trademarks and Logos 1-5

1.8 Legal Provisions 1-5

1.9 Prevention of accidents 1-6

1.10 Choice of material to use: Ecology - Recycling 1-6

1.11 Vehicle delivery 1-7

1.12 Vehicles Identification 1-8

1.13 Dimensions and weights 1-9

1.13.1 General Specifications 1-9

1.13.3 Observing the Permitted Weights 1-13

1.15 Quality System management 1-15

1.16 Vehicle maintenance 1-15

1.17 Conventions 1-16

Aim of bodybuilders instructions

1.1 Aim of bodybuilders instructions

1.2 IVECO “no objection” for changes and fittings

Aim of bodybuilders instructions

Maintaining the functionality of vehicle components.

1.5 Request for a “no objection”

IVECO technical documents available by means of computer

1.6 IVECO technical documents available by means of computer

The following technical documents are available on the Internet at www.thbiveco.com:

1.7 Trademarks and Logos

Instruction for added assemblies

1.8 Legal Provisions

IVECO technical documents available by means of computer

1.9 Prevention of accidents

1.10 Choice of material to use: Ecology - Recycling

1.11 Vehicle delivery

Prior to delivering the vehicle, the body builder shall:

1.12 Vehicles identification

Cab Model Power Version Suspension

CAB RANGE VERSION MISSION

AS = Active Space T = Tractor GV = Bulky Goods

/TN = 6x2P, mechanics with third fixed axle to twinned wheels

Dimensions and weights