RT809H ISP Programmer User/Instruction Manual by RT809.

com

Important information:

1.This instruction is suitable for RT809H programmer.

2.In order to connect the programmer more conveniently and faster,please connect
the hardware after installing the software.

3.Please read the instruction carefully before using the programmer.

4.Please use the original USB data cable.

Copyright Statement

Software copyright WWW.IFIX.NET.CN

User manual copyright WWW.IFIX.NET.CN Rock Group

RT809 series of programmers have acquired 6 China National invention patents,any unit or
individual is not allowed to copy,photograph,regenerate,translate or restore to any form of
electronic media readable by other machines,or will be investigated for legal responsibility.

This manual is subject to change without notice.

Once there are some differences against this instruction caused by software upgrade please follow to
the software.
Chapter 1 General Description

1.1 Brief

1.1.1 What is RT809H?

RT809H is a kind of cost-effective,reliable and fast universal programmer series,suitable for all the
computers or laptops based on Pentium IV processors or the better processors.When working it can
communicate with the USB2.0 fast port of computer directly,with driver program inside software,which
makes installing operation more convenient.

1.1.2 Programmer Characteristic:

 Supporting Windows XP,Windows Vista,Windows 7,windows 8 and windows 10

 Do not need external power source,with low-power consumption,can be used as VGA signal
generator,easy to repair.
 With Intellisense functionality,when reading and writing most types of chip off line, it support
the function of intelligent identification and being put at will.
 Support 24/25/93/95 series serial SPI Flash. EEPROM offline read and write.
 Support 26/27/28/29/30/39/49/50 series NOR Flash/ PROM read and write;
 Support TSOP48/BGA footprint NAND Flash parameter automatic identification and offline
reading;
 Support the mainstream device,including E/EPROM、MCU、EC、SPI NOR flash、parallel NOR
flash、SPI NAND、parallel NAND、ONENAND、MCP、EMMC、EMCP,etc.
NAND_AUTO Can recognize most of the NAND and go on to read and write.
EMMC_AUTO Using BGA socket,supporting EMMC off-line fast read-writing(8bit main line)
EMMC_AUTO_4BIT Using BGA socket,supporting EMMC off-line fast read-writing(4bit main line)
EMMC_AUTO_ISP Read-write EMMC with flying line way.(1bit main line)
Support the EMMC recognition in the on-line or off-line way,BOOT/USER/RPOM/GPP area
read and write.
 I2C/ serial port ISP has strong function,compatible with most of the LCD chip scheme,can
check the printing information on line,read and write NOR/NAND/EMMC chip on line,read
and write the EC chip of laptop on line or off line.
 Support the IT8/KB90/NPCE/NEC16 series of laptop mainboard’s EC chip to read and write.
 High-speed USB port,USB driver with WHQL certification,the reading and writing speed can be
as much as 25 MB/S.
 Full driver structure,free software upgrade,the universal switch socket to reduce the using cost
for the user.

https://www.RT809.com
 1.1.3 Instruction Tissue

This instruction consists of three parts:

The part one is to introduce RT809H,including the system requirement,software and hardware
installing,etc ;
The part two is the detailed instruction of software commands and each function;
The part three is appendix,including the user support and the wrong message.

1.1.4 System Requirement

Minimum system configuration:

 Pentium IV and above compatibles,desktop or laptop computer,at least a universal serial main
line port conform to USB2.0 high-speed standard.
 Windows XP/Vista operating system.
 The hard disk with at least 1G free space.

1.1.5 Programmer External Port Instruction

 Front view : HMI is reserved man-machine port,also be used by the footprint chip of
TSOP56,BGA64,etc.
 DC lateral view : Except the USB outlet connected to the computer,there is a DC power supply
outlet,9-12V power supply range(negative electrode outside and positive electrode
inside),switching automatically between external power source and USB power supply.
(Please use the power of good quality,or the programmer will may be damaged and no
warranty.)

 Flashing port lateral view:

 Port instruction:
 The leftmost button is the power button, also as the VGA signal switching button;
 The IDC10 black outlet at the middle is ISP port,the main function is ISP of all sorts of
MCU and flying line to read and write EMMC,etc.Use the Dupont line to connect this port
 with the key signal of the board waiting for flashing, one to one correspondence
connection.
 “VGA ISP”can be used as VGA signal output,be connected with the VGA port of the
board when flashing.
 “VGA IN”is the VGA signal input,can be connected with the computer graphics.
When unconnected,VGA ISP will output the VGA signal produced by itself;
When connected,VGA ISP output the computer graphics signal;
 “HDMI Digital high-definition interface”can connect with the HMDI port of the flashing
board.

1.1.6 Programmer Packing

 The standard packing:
Programmer mainframe 1
DIP 48 pin simple soldering board 1
SOP simple soldering board 1
USB2.0 high-speed cable 1
VGA connecting line 1
 Chapter 2 Installing

If you are the first time to use RT809H USB universal programmer,please surf the programmer
official web to download the latest software.
http://www.ifix.net.cn/thread-56912-1-1.html
Like this:

The file downloaded is ZIP format,should be unzipped before using.

Before unzipped After unzipped

2.1 Installing the Programmer Application Software

2.1.1 Installing the Software

Step 1:Move the mouse to this icon,double-click the right mouse button to start installation;

Step 2:Select the language in demand,if you need Chinese click “OK”directly;

Step 3:Click the “Next”;

Step 4:Click the “Agree”;
Step 5:Click the “Next”;

Step 6:Don’t change the path,click “Next”;

Step 8:Click the “Install”;

Step 9:Start to install,waiting to finish the progress bar;

Step 10:Click the “Add”;

Step 11:Click the “Uninstall”;

Step 12:Click the “OK” and then “Cancel”,then the installation has finished.
2.1.2 Installing the drivers

Step 1:Connect the computer with the programmer using the UCB line in packing,the computer
will tell that there is a new hardware;

Step 2:Select “Browse my computer for driver software”;

Step 3:Click the arrow at the right side down,change the path into “D:\809H\DRIVER”,then click
“Next”;
Step 4:Click “Complete”,USB Serial Converter A driver has installed already;
Step 5:Next go on to install the driver of USB Serial Converter B,click “Next”;

Step 6:Click “complete”,the driver has been installed already;

Open the operating software of 809H,the serial number of programmer will show.The serial number
is the important document of technical support and warranty.

Please do not leak, properly kept.

Chapter 3 The Software Instruction

3.1 Software Interface Instruction

Click this icon to recognize intelligently the
type of most of the chip,easy to operate.
When connecting the mainboard to
flash,click this icon it will recognize the
mainboard scheme,easy to operate.
Click this icon to check,read or write the
hexadecimal data.
Click this icon to jump into the third-party
flashing software.

To input the printing letter on the chip type.

Click it after inputting the printing letter.

Operating area,the chip can be
read,written,verified,erased,blacked,protecte
d and so on.

Operating menu.

Click this icon to check the content of buffer.

Click the “tool” and the pull-down menu

appear.

Click this icon and the pull-down menu

appear to change the language type.
Click the “setting”,the pull-down menu
appear.

Click “Programming Setup Options”

The others are not needed to select,when ISP
online flashing the mainboard,you should
change the line sequence by yourself in the
ISP setting.

Click this icon to uninstall the programmer

driver.

Click this icon to reload the progammer

driver.
Click this icon to repair the programmer
firmware.

Click this icon to add the new chip.

Click this icon to add the new flashing

software.

Click this icon to check the priting

information of the repair mainboard.

Click this icon to self-test the serial port.

Click this icon to to BOOT upgrade.

Click the icon of parameter setting to set the

ISP on-line serial port.

To set the parameters like serial port line

sequence,Baud rate and so on.

Click “serial port print”to open the serial

port printing function.
Display the printing information here.
Chapter 4 Detailed Operation

4.1 24XX,25XX,93XX Series Chips’ Reading and Writing

4.1.1 93XX’s Reading and Writing

Step 1:93XX chip’s selecting

 Input “93” in the “Input Chip Printing Letter”,select the detailed chip type at the lower
right,then click “OK” after selecting.

 Use the putting position of simple switch board,,when welding chip the 1 foot is at the lower
left.(Support the 93XX,24XX,25XX to be placed at will)
 When using the bounce seat,one foot of the chip should correspond to the top left corner.

Step 2: Reading the chip

 Click “Read” in the icon.

 Change the name of the file read.

 Select the saving path at the top right corner.

Step 3:Writing the chip

 Click “Write” in the picture.

 Select the file going to be written and click “Open”.

 Then it will hint that the writing succeed,after verifying the writing will finish.
 4.1.2 24XX,25XX’s Reading and Writing

Step 1:24,25 chip’s selecting

 Use to identify the type of the chip,easy to use.

 Or input the letter of chip.

Step 2:The other steps are the same with 93XX’s.

4.2 PLCC Encapsulation Chip’s Reading and Writing

According to the difference of the encapsulation,when selecting the different switching seat to
install,the user should follow the principle that make the gap upwards and the bottom aligned.(Please
buy the established switching seat on the official website.)
 Then input the type in the “Enter chip printing”,the way of reading,saving and writing are the
same with 93XX.

4.3 TSOP48 Encapsulation Chip’s Reading and Writing

 Select simple seat or the bounce seat with 48 feet;

 Put the chip on the programmer,click the icon to see if it can recognize
the type of the chip;

 Can also enter the chip printing.

If it is the NAND chip,input the “NAND _AUTO” in the “Enter chip printing”.
  The way of reading,saving and writing are the same with 93XX.

Attention:When using the bounce seat,please check carefully if contacts are in good
condition.If the reading fail,try more times.If it still fails,please weld on the simple board to
try.Otherwise it is important to weld well and clean the soldering paste,or it is easy to make
some mistake under situation of high frequency.

4.4 EMMC’s Reading

 Choose the approved EMMC seat,don’t use the third-party seat,the sign of the chip should
be in the direction of lower left.(EMMC must 植株,and be cleaned up or it will make the
mistake easily)
 Click to choose the printing letter,the default is EMMC_AUTO_4BIT.Can
also input “EMMC”in the “Enter chip printing”.

 EMMC_AUTO_4BIT:Slow-speed reading,but with high stability, higher successful rate,software

default.

EMMC_AUTO_8BIT:High-speed reading,suitable for most of the EMMC chips.

If read and write on line,please choose EMMC_AUTO_ISP.

 Click “Setting” then the dialog box in the middle pop up.

The left is the 5 partitions of EMMC,the “USER” is the user area,“RQMB”is the encryption
area,the data in it can not come out so don’t have to be chosen.

The right is VCCQ power supply choice,it’s 3V generally,very few chip need to choose 1.8V.

 The success hint of reading chips:

  The software will create a folder automatically after EMMC already read the data,there will be
the data of corresponding area,it’s alright to save the whole folder.

(When the capacity of EMMC is more than 4G,the file read be divided into 2 parts
automatically,it is normal that there will be 5 files.)

 When writing EMMC,drag just an icon into the display area of software then all the file will be
loaded to the software.

4.5 Laptop EC Chip’s Reading and Writing

4.5.1 1:85XX Series EC Chip’s Reading and Writing

The location of chip on the simple board，and the direction of switching board.
Reading

Writing

4.5.2 KB9012 Chip’s Reading and Writing

The capacitance of the switching board is 104,the resistance is 473.

 Reading chip.

Writing chip.

4.5.3 NPCE 288,388 Chip’s Reading and Writing

The resistance of the switching board is 103,the one foot of the chip is at the white point,and the
gap of the switching board should be upward and the bottom be aligned.
Reading

Writing
Chapter 5 ISP (on-line) Operation Application Instruction

5.1 Checking Liquid Crystal Board Printing Message

Step 1 : Connect the VGA ISP of flashing programmer with the VGA port of liquid crystal board
using VGA line(using the original packing VGA line);

Step 2 : At first click the in the software interface to set;

Step 3 :

Set when the window pops up.

VGA line orders type : The different mainboard will use the different line orders, if it can’t on
line,please choose different line orders to test repeatedly.

Serial port speed : That is baud rate adjustment,the baud rate of different mainboard is different.If
the printing message is messy code please try to change the baud rate.

After adjusting the parameter please click to save.

 Step 4 : After setting the parameter,click ,open the serial and electrify the
mainboard in 2 seconds,the printing message will appear in the following dialog.

Attention : If the printing message haven’t been appeared,please pay attention to following
questions

 First click ,then supply power to the mainboard;

  Some mainboards need to be supplied power in the stand-by mode and also the main power
supply;

 If the line orders are not correct,please change it in the parameter setting and then try again;

 When the serial port of some mainboards is at HDMI or reserved port,it needs to connect
HDMI or fly lines,that is to connect SCL,SDA,GND lines with the SCL,SDA,GND on the
mainboard;

 The serial ports of some mainboard need to be opened in the factory pattern.

5.2 LCD TV Mainboard Program’s Transcription

5.2.1 MST scheme

Taking board number：08-MS80105-MA200AA，TCL MS801movement，L46E5500A computer

type，main chip MSD6A801，storage W25Q16 as the example.The ISP path and serial port of this
version are the same port,both have 2 sets.Line orders 1 and line orders 4 can both receive printing
message and and reveal the MBOOT program alone,and here we use line orders 1.
The way to back-up the program : “ISP automatic identification”→“Read”→“Save”.

Step 1 : The VGA ISP port should be connected with board correctly by VGA line.Open the

software to the main interface,first click ,then charge the mainboard(Keeping

booting up,both with standby power supply and main power supply),then it will hint to detect
the type of main chip.
 Step 2 : Click ,809F will read and verify once automatically.(If it verifies by
mistake,please set the low speed in the “setting” menu to read again )
 Step 3 : Save the file after reading,try your best to name the file in detail,including the
manufacturer,brand,model,screen type,main chip type,memorizer type.
5.2.2 Burning Method

Key point:“ISP automatic identification”“Open”the file waiting for burning“Write”

Step 1 : The VGA ISP port should be connected with board correctly by VGA line.Open the

software to the main interface,first click ,then charge the mainboard(Keeping

booting up,both with standby power supply and main power supply),then it will hint to detect
the type of main chip.
Step 2 : Select the program file waiting for burning;
 Step 3 : Setting the data reconstitution function to reserve the information like original MAC
address and so on;
 Step 4 : Click the ,recombine the data automatically,erase,write,verify,you just
need to wait for finishing.
5.2.3 MTK Scheme Flashing Method

Mechanism chip : Skyworth 8k27

Main chip : MT8222
Memorizer : MX25L6405
Board type : 715G4089-M01-000-004L

Back-up method outline : Setting the VGA line orders by hand → Choose the chip type → Read →
Save

 Reading:

Step 1 : Connect the programmer VGA IS port with the board by VGA line correctly and supply
the power,open the software to the main interface,like following picture,set the VGA line orders;
 Step 2 : Input the type ”MT822X_SPI#ISP” in the “Enter Chip Printing” on the software main
interface;

Step 3 : Click on the interface;

 Step 4 : Click to save the file after finishing reading.Try the best to name the file
in detail,including the manufacturer,board number,screen type,main chip type,memorizer type for
the convenient use in the later.
  Writing:

Set the VGA line orders by hand → Select the chip type → Open the file → Write

Step 1 : The same as above;

Step 2 : The same as above;

Step 3 : Click on the interface and choose the file waiting for being written;

Step 4 : Click on the interface,according to the words as shown in following

picture it means the writing has finished.
5.2.3 RTD Scheme

Main chip : RTD2674S

Memorizer : MX25L3205
Board type : 715G3934-M03-000-004F
 Back-up outline : Set the VGA line order manually → Choose the chip type → Read → Write

 Reading:
Step 1 : Connect the programmer VGA IS port with the board by VGA line correctly and supply
the power,open the software to the main interface,like following picture,set the VGA line orders;

Step 2 : Input the type ”RTD_DRAGON_SPI #ISP” in the “Enter Chip Printing” on the software
main interface;
 Step 3 : Click on the software interface,operate according to the hint;

Step 4 : Click to save the file after finishing reading.Try the best to name the file
in detail,including the manufacturer,board number,screen type,main chip type,memorizer type for
the convenient use in the later.
  Writing:
The writing method : Set the VGA line orders by hand → Select the chip type → Open the file
→ Write

Step 1 : The same as above;

Step 2 : The same as above;

Step 3 : Click on the interface and choose the file waiting for being written;
 Step 4 : Click on the interface,according to the words as shown in following
picture it means the writing has finished.
5.2.4 EMMC_ISP Reading and Writing Tutorial

Board model:Skyworth coocaa 8A13

 Step 1 : In order to stop the main chip working (power supply,clock,restoration),the easiest way
is crystal oscillator, ground the 2 pins of the crystal oscillator X0R2(beside the shielded wire
extension cord) of the main chip;

Step 2 : Find a few key pin test points DO,CMD,CLK,GND,at least 4 lines,and the line should be
better within 10cm.
Step 3 : EMMC uses the power supply of board by self,so one line less,just need to supply the
12V power to the board.
Step 4 : Supply the 12V power to the Liquid Crystal mainboard,open the software of the
programmer,choose EMMC_AUTO_ISP and then click ”Read”.

The method of EMMC_AUTO to fly ISP line to write please refer to the EMMC offline writing
method.

EMMC_AUTO_ISP flying line read-writing must stop the main chip working,then the efficiency
of read-writing can be high.
The way includes : Stop the power supply,short sub the 2 pins of main chip crystal oscillator to
the ground,supply the power to the reset pin to force to reset.

The easiest way is to short sub the 2 pins of main chip crystal oscillator to the ground,use the
original power supply,the voltage of the VCCIO is the same as the EMMC power supply,fly 4
lines (CLK/CMD/D0/GND) to write.
5.2.5 On-line Reading IT85XX Series Laptop EC Chip

Wiring diagram(Provide the FPC line and socket : three kinds of separation
distance:1mm,0.5mm,0.8mm,the FPC socket is 32pin connected down,FPC line is 24pin with the
same direction,also can cut out the 32pin line into 24pin to be used)

Important instruction:
1.Don’t forget to connect the GND,don’t forget to connect the ground,the ground line can
not be too slim;
2.The FPC line must be cut and plug as requested,then we can see the clipping and connection
in the following high-definition wiring diagram,which must be clear;
3.For the IT8586/IT8587 chip,if it can’t enter the ISP mode,please fly the NO.100 pin of chip to
GND(The NO.100 pin must be low level).But it don’t need to fly line if it uses the switch board
of V1.5 type;
4.Must not plug in when selecting the type and setting the line orders,can only after finishing
the setting and click “read” or “write”;
5.When there are some board can not be connected,please turn off and plug in again,this kind
of chip aims to catch the ISP ENTER signal when supply electricity.
6.If it still can’t be connected,please check for the line order you want in the

（ ） in the software of programmer,but if there is no the line order you want

you can add the line order by yourself.

Laptop mainboard : Lenovo Y400,Board LA8691P,EC type IT8580. The other types like IT8586E，
IT8586G，IT8585E,IT8587E and so on of TQFP128 和 BGA footprint EC,the reading and writing
way:
Chapter 6 Laptop EC Chip MEC1633_MEC1609_MEC16 Series
Flying Line Read-Write
Connect the test point with the simple socket with the wire.
Chapter 7 Secure CRT Software Installation

Step 1 : Click ,the software appear;

Step 2 : Click ;
Step 3 : Click the “fast connect” icon in the middle in the following picture.

Step 4 : Choose “Serial”in the protocol;

Step 5 : The port should be selected the same with it in device manager;

Step 6 : After choosing click “Connect”,this computer use COM4,after finishing setting click
“Connect”,once connect successfully there will be hint;
Connect normally:
Chapter 8 Common Problem Diagnosis

8.1 Installing the software and driver unsuccessfully

 First to ensure that the hardware configuration can not be too low,there must be enough
space in D disk;
 Try the best to use Inter CPU computer,the compatibility of AMD CPU is not good.
 Change the different versions of operation system please try best to use the pure operation
system;
 Close the similar software like antivirus software or computer keeper in the computer;
 Install correctly according to the hint in the instruction.

8.2 Programmer Unconnected with the Mainframe

 Use the original USB line;

 Please connect the USB2.0 port,some chip can’t be brushing written through USB3.0 port;
 AS the desktop computer,please use red 5V power-supply USB port,the purple one can’t
supply enough power.

8.3 The use of programmer selftest command,to check if there is

problem itself.

8.3.1 Selftest way 1:

Step 1 : Input the “SELFTEST” in the “Enter chip printing”,click ;

Step 2 : Click ,look at the hint in the display area,”selftest 0” means the test
pass;
Step 3 : Install the NO.1 test board and the short port of VGA ISP(short circuit the 4pins and
11pins,12pins and 15pins);

Step 4 : Click ,check the hint in the software,it will hint “Selftest 1,test pass”;
Step 5 : Install the NO.2 Self Test Board;

Step 6 : Click ,check the hint in the software,it will hint “Selftest 2, test pass”;

8.3.2 Selftest way 2 :

Step 1 : When there is no chip on the locking seat,input the type of 25XX in “Enter Chip
Printing”;
Step 2 : Click ,it will hint that there is no chip or the locking seat hasn’t been
impacted well,which is normal;

If it hints that there may be a pin empty solder;

Attention : In the case of that some users have no test board,as long as the selftest 0 and 25 chip
test pass,the machine is normal.

If there is other hints when doing selftest 0,the way to deal with it could be as following:

 The problem of connection with computer and the programmer,please step-by examine
according to the hint of failure process;
  Hardware trouble like pin electric leakage,problems inside the pins,VPP open circuit,GND
open circuit,VPP short circuit,VCC short circuit,GND short circuit,VPP protection not shut
off,which must be returned to factory to repair.

8.4 The Method of Solving the Problem When reading

25XX,24XX,93XX

The programmer do the self test;

Original USB line;
Make sure of the enough power supply of 5V (red line) for the desktop computer;
With nice 24XX,25XX,93XX chips(a new one is not always the nice one);
Use the simple board to replace the bounce seat,clean the welding paste after welding.

Cancel the √ of in the programming setup options,click ;

The problem easy to appear when reading NAND chip : byte verify inconformity.

8.4.1 Handling Method

 Don’t use the NAND AUTO when there is other choice;
The chips pins dispose : 90% of the broken chips because of the not enough cleaning;
Weld on the simple board instead of bounce seat(must be cleaned up);
Remember to grinding the chips(with the same type,different ID)
Pay attention to the suffix of the Samsung chip(it’s unusable with same type but different
suffix)

8.5 The Method to Solve the Problem of Off-line Read and Write
EMMC

Step 1 : The EMMC must make planting-beads and wipe up the tin beads with the newspaper,and
also change the VCCQ voltage in the setting;

Step 2 : If the EMMC_AUTO_8BIT can’t work,use the EMMC_AUTO_4BIT to have a try;

If it can’t work by reading four areas on the left,try to read a area alone;
Exchange the chip of same type to try(make sure of the chip well or not);
Fly line reading EMMC mistake:
 Step 3 : Make sure of the length of the flying line in 10CM;
If the signal line and EMMC key port connect correctly;
If the EMMC power supply is normal,it is generally 3.3V or double power of 3.3V and
1.8V;
If the main chip has stopped working(power supply,clock,restoration),complete one is
OK;
Or remove the resistance connecting with the signal line,weld the fly line on the welding
pad beside to EMMC;

The EMMC chip damage itself : The reading has not finished(half or more),try more times to see if
it’s the same position every time.

The EMMC chip damage itself(find the mainboard with same chip);
Clean away the external interference(obvious for desktop computer) : electric soldering iron
on-off,light on-off,etc.

8.6 The Method to Deal with the LCD Mainboard Printing

Information Messy Code

Most reason is the wrong Baud rate,please choose these four Baud rate to have a try:
Technical support way: Repairing forum : http://www.ififorumx.net.cn(Ifix)
Present 1000 points after buying RT809H to download the data.
Technical support TEL:13600024226
Technical support WeChat：13600024226
Technical support QQ:113536588
Landline phone：020-28667686

Guarantee clause：
RT809H has a year of free maintenance service from the date of purchase, the following is not in
the scope of free maintenance ——
1.
1.Man-made damage（Connect the wrong plug,appearance broken）；
2.The external equipment damage（Electric leakage of computer USB,the repairing board damage
badly or electric leakage）；
3.Irresistible force（Lightning stroke or earthquake or other natural disaster）；
4.Out of the warranty（Unable to provide the purchase date，warranty of 15 months according to
the date of the serial number）；
5.The machine which need to pay for repairing,you just need to pay for the parts but not service.

Editor's Note：Although we try to do our best ,but, error is inevitable.If you find some
mistake,Welcome to contact us, we expressed the sincere thanks..