LTC2368-16 16-Bit, 1Msps, PseudoDifferential Unipolar SAR ADC with 94.

7dB SNR FEATURES

n n n n n n n n n n n n n n n

DESCRIPTION
The LTC2368-16 is a low noise, low power, high speed 16-bit successive approximation register (SAR) ADC. Operating from a 2.5V supply, the LTC2368-16 has a 0V to VREF pseudo-differential unipolar input range with VREF ranging from 2.5V to 5.1V. The LTC2368-16 consumes only 13.5mW and achieves 0.75LSB INL maximum, no missing codes at 16 bits with 94.7dB SNR. The LTC2368-16 has a high speed SPI-compatible serial interface that supports 1.8V, 2.5V, 3.3V and 5V logic while also featuring a daisy-chain mode. The fast 2Msps throughput with no cycle latency makes the LTC2368-16 ideally suited for a wide variety of high speed applications. An internal oscillator sets the conversion time, easing external timing considerations. The LTC2368-16 automatically powers down between conversions, leading to reduced power dissipation that scales with the sampling rate.
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and SoftSpan is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 7705765.

1Msps Throughput Rate 0.75LSB INL (Max) Guaranteed 16-Bit No Missing Codes Low Power: 13.5mW at 1Msps, 13.5W at 1ksps 94.7dB SNR (Typ) at fIN = 2kHz 118dB THD (Typ) at fIN = 2kHz Guaranteed Operation to 125C 2.5V Supply Pseudo-Differential Unipolar Input Range: 0V to VREF VREF Input Range from 2.5V to 5.1V No Pipeline Delay, No Cycle Latency 1.8V to 5V I/O Voltages SPI-Compatible Serial I/O with Daisy-Chain Mode Internal Conversion Clock 16-Lead MSOP and 4mm 3mm DFN Packages

APPLICATIONS
n n n n n n

Medical Imaging High Speed Data Acquisition Portable or Compact Instrumentation Industrial Process Control Low Power Battery-Operated Instrumentation ATE

TYPICAL APPLICATION
32k Point FFT fS = 1Msps, fIN = 2kHz
2.5V 10F VREF 0V 1.8V TO 5V 0.1F AMPLITUDE (dBFS) OVDD 0 20 40 60 80 100 120 140 160 180 0 100 200 300 FREQUENCY (kHz) 400 500 SNR = 94.7dB THD = 118dB SINAD = 94.7dB SFDR = 119dB

+
LT6202

10 10nF

VDD IN+

LTC2368-16 IN REF GND

CHAIN RDL/SDI SDO SCK BUSY CNV

236816 TA01a

SAMPLE CLOCK

2.5V TO 5.1V

47F (X5R, 0805 SIZE)

236816 TA01b

236816f

LTC2368-16 ABSOLUTE MAXIMUM RATINGS

(Notes 1, 2)

Supply Voltage (VDD) ...............................................2.8V Supply Voltage (OVDD) ................................................6V Reference Input (REF).................................................6V Analog Input Voltage (Note 3) IN+, IN .........................(GND 0.3V) to (REF + 0.3V) Digital Input Voltage (Note 3) .......................... (GND 0.3V) to (OVDD + 0.3V) Digital Output Voltage (Note 3) .......................... (GND 0.3V) to (OVDD + 0.3V)

Power Dissipation .............................................. 500mW Operating Temperature Range LTC2368C ................................................ 0C to 70C LTC2368I .............................................40C to 85C LTC2368H .......................................... 40C to 125C Storage Temperature Range .................. 65C to 150C

PIN CONFIGURATION
TOP VIEW CHAIN VDD GND IN
+

1 2 3 4 5 6 7 8 17 GND

16 GND 15 OVDD 14 SDO 13 SCK 12 RDL/SDI 11 BUSY 10 GND 9 CNV

TOP VIEW CHAIN VDD GND IN+ IN GND REF REF 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 GND OVDD SDO SCK RDL/SDI BUSY GND CNV

IN GND REF REF

DE PACKAGE 16-LEAD (4mm 3mm) PLASTIC DFN TJMAX = 150C, JA = 40C/W EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB

MS PACKAGE 16-LEAD PLASTIC MSOP TJMAX = 150C, JA = 110C/W

ORDER INFORMATION
LEAD FREE FINISH LTC2368CMS-16#PBF LTC2368IMS-16#PBF LTC2368HMS-16#PBF LTC2368CDE-16#PBF LTC2368IDE-16#PBF TAPE AND REEL LTC2368CMS-16#TRPBF LTC2368IMS-16#TRPBF LTC2368CDE-16#TRPBF LTC2368IDE-16#TRPBF PART MARKING* 236816 236816 23686 23686 PACKAGE DESCRIPTION 16-Lead Plastic MSOP 16-Lead Plastic MSOP 16-Lead Plastic MSOP 16-Lead (4mm 3mm) Plastic DFN 16-Lead (4mm 3mm) Plastic DFN TEMPERATURE RANGE 0C to 70C 40C to 85C 40C to 125C 0C to 70C 40C to 85C

LTC2368HMS-16#TRPBF 236816

Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/

236816f

LTC2368-16
The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL VIN+ VIN VIN+ VIN IIN CIN CMRR PARAMETER Absolute Input Range (IN+) Absolute Input Range (IN) Input Differential Voltage Range Analog Input Leakage Current Analog Input Capacitance Input Common Mode Rejection Ratio Sample Mode Hold Mode fIN = 500kHz CONDITIONS (Note 5) (Note 5) VIN = VIN+ VIN
l l l l

ELECTRICAL CHARACTERISTICS

MIN 0.1 0.1 0

TYP

MAX VREF + 0.1 0.1 VREF 1

UNITS V V V A pF pF dB

45 5 80

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL PARAMETER Resolution No Missing Codes Transition Noise INL DNL ZSE FSE Integral Linearity Error Differential Linearity Error Zero-Scale Error Zero-Scale Error Drift Full-Scale Error Full-Scale Error Drift (Note 7)
l

CONVERTER CHARACTERISTICS

CONDITIONS
l l

MIN 16 16

TYP

MAX

UNITS Bits Bits

0.5 (Note 6) (Note 7)

l l l

LSBRMS 0.75 0.5 4 20 LSB LSB LSB mLSB/C LSB ppm/C

0.75 0.5 4 20

0.1 0.1 0 4 2 0.1

DYNAMIC ACCURACY
SYMBOL PARAMETER SINAD SNR

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C and AIN = 1dBFS. (Notes 4, 8)
CONDITIONS fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 5V, (H-Grade) Signal-to-Noise Ratio fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 2.5V fIN = 2kHz, VREF = 5V, (H-Grade) fIN = 2kHz, VREF = 2.5V, (H-Grade) THD SFDR Total Harmonic Distortion Spurious Free Dynamic Range 3dB Input Bandwidth Aperture Delay Aperture Jitter Transient Response Full-Scale Step fIN = 2kHz, VREF = 5V fIN = 2kHz, VREF = 2.5V fIN = 2kHz, VREF = 5V
l l l l l l l l l

MIN 91.9 91.7 92.5 87.7 92.2 87.3

TYP 94.7 94.7 94.7 90.7 94.7 90.7 118 116

MAX

UNITS dB dB dB dB dB dB

Signal-to-(Noise + Distortion) Ratio

101 101

dB dB dB MHz ps ps ns

102

120 34 500 4 460

236816f

LTC2368-16 REFERENCE INPUT

SYMBOL VREF IREF PARAMETER Reference Voltage Reference Input Current

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS (Note 5) (Note 9)
l l

MIN 2.5

TYP 0.5

MAX 5.1 0.7

UNITS V mA

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
SYMBOL PARAMETER VIH VIL IIN CIN VOH VOL IOZ ISOURCE ISINK High Level Input Voltage Low Level Input Voltage Digital Input Current Digital Input Capacitance High Level Output Voltage Low Level Output Voltage Hi-Z Output Leakage Current Output Source Current Output Sink Current IO = 500A IO = 500A VOUT = 0V to OVDD VOUT = 0V VOUT = OVDD
l l l

DIGITAL INPUTS AND DIGITAL OUTPUTS

CONDITIONS

MIN
l l

TYP

MAX 0.2 OVDD

UNITS V V A pF V

0.8 OVDD 10 5 OVDD 0.2 0.2 10 10 10 10 10

VIN = 0V to OVDD

V A mA mA

POWER REQUIREMENTS
SYMBOL VDD OVDD IVDD IOVDD IPD IPD PD PARAMETER Supply Voltage Supply Voltage Supply Current Supply Current Power Down Mode Power Down Mode Power Dissipation Power Down Mode Power Down Mode

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l

MIN 2.375 1.71

TYP 2.5 5.4 0.9 0.9 0.9 13.5 2.25 2.25

MAX 2.625 5.25 6.3 90 140 15.8 225 315

UNITS V V mA mA A A mW W W

1Msps Sample Rate 1Msps Sample Rate (CL = 20pF) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V, H-Grade) 1Msps Sample Rate Conversion Done (IVDD + IOVDD + IREF, VREF > 2V) Conversion Done (IVDD + IOVDD + IREF, VREF > 2V, H-Grade)

l l l

ADC TIMING CHARACTERISTICS

SYMBOL fSMPL tCONV tACQ tCYC tCNVH tBUSYLH tCNVL tQUIET tSCK tSCKH PARAMETER Maximum Sampling Frequency Conversion Time Acquisition Time Time Between Conversions CNV High Time CNV to BUSY Delay Minimum Low Time for CNV SCK Quiet Time from CNV SCK Period SCK High Time

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l

MIN 460 460 1 20

TYP

MAX 1 527

UNITS Msps ns ns s ns

tACQ = tCYC tCONV tBUSYLH (Note 10)

l l l

CL = 20pF (Note 11) (Note 10) (Notes 11, 12)

l l l l l

13 20 20 10 4

ns ns ns ns ns
236816f

LTC2368-16 ADC TIMING CHARACTERISTICS

SYMBOL tSCKL tSSDISCK tHSDISCK tSCKCH tDSDO tHSDO tDSDOBUSYL tEN tDIS PARAMETER SCK Low Time SDI Setup Time From SCK SDI Hold Time From SCK SCK Period in Chain Mode SDO Data Valid Delay from SCK SDO Data Remains Valid Delay from SCK SDO Data Valid Delay from BUSY Bus Enable Time After RDL Bus Relinquish Time After RDL (Note 11) (Note 11) tSCKCH = tSSDISCK + tDSDO (Note 11) CL = 20pF (Note 11) CL = 20pF (Note 10) CL = 20pF (Note 10) (Note 11) (Note 11)

The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 4)
CONDITIONS
l l l l l l l l l

MIN 4 4 1 13.5

TYP

MAX

UNITS ns ns ns ns

9.5 1 5 16 13

ns ns ns ns ns

Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may effect device reliability and lifetime. Note 2: All voltage values are with respect to ground. Note 3: When these pin voltages are taken below ground or above REF or OVDD, they will be clamped by internal diodes. This product can handle input currents up to 100mA below ground or above REF or OVDD without latch-up. Note 4: VDD = 2.5V, OVDD = 2.5V, REF = 5V, fSMPL = 1MHz. Note 5: Recommended operating conditions. Note 6: Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. The deviation is measured from the center of the quantization band.

Note 7: Zero-scale error is the offset voltage measured from 0.5LSB when the output code flickers between 0000 0000 0000 0000 and 0000 0000 0000 0001. Full-scale error is the deviation of the last code transition from ideal and includes the effect of offset error. Note 8: All specifications in dB are referred to a full-scale 5V input with a 5V reference voltage. Note 9: fSMPL = 1MHz, IREF varies proportionately with sample rate. Note 10: Guaranteed by design, not subject to test. Note 11: Parameter tested and guaranteed at OVDD = 1.71V, OVDD = 2.5V and OVDD = 5.25V. Note 12: tSCK of 10ns maximum allows a shift clock frequency up to 100MHz for rising capture.

0.8*OVDD 0.2*OVDD tDELAY 0.8*OVDD 0.2*OVDD tDELAY 0.8*OVDD 0.2*OVDD 50%

tWIDTH 50%
236816 F01

Figure 1. Voltage Levels for Timing Specifications

236816f

LTC2368-16
fSMPL = 1Msps, unless otherwise noted. Integral Nonlinearity vs Output Code
1.0 0.8 0.6 DNL ERROR (LSB) INL ERROR (LSB) 0.4 0.2 0.0 0.2 0.4 0.6 0.8 1.0 0 16384 32768 49152 OUTPUT CODE 65536
236816 G01

TYPICAL PERFORMANCE CHARACTERISTICS

Differential Nonlinearity vs Output Code
0.5 0.4 0.3 0.2

TA = 25C, VDD = 2.5V, OVDD = 2.5V, REF = 5V,

DC Histogram
100000 90000 80000 70000 COUNTS 60000 50000 40000 30000 20000 10000 0 = 0.5

0.1 0.0 0.1 0.2 0.3 0.4 0.5 0 16384 32768 49152 OUTPUT CODE 65536
236816 G02

32676

32677

32678 CODE

32679

32680
236816 G03

32k Point FFT fS = 1Msps, fIN = 2kHz

0 20 40 AMPLITUDE (dBFS) 60 80 100 120 140 160 180 0 100 200 300 FREQUENCY (kHz) 400 500
236816 G04

SNR, SINAD vs Input Frequency

100 95 SNR, SINAD (dBFS) 90 SINAD 85 80 75 70 SNR 60 70 HARMONICS, THD (dBFS) 80 90 100 110 120 130 140 150 0 25 50 75 100 125 150 175 200 FREQUENCY (kHz)
236816 G05

THD, Harmonics vs Input Frequency

SNR = 94.7dB THD = 118dB SINAD = 94.7dB SFDR = 119dB

THD 2ND 3RD

160

25

50

75 100 125 150 175 200 FREQUENCY (kHz)

236816 G06

96.0 95.5 SNR, SINAD (dBFS) 95.0 94.5 94.0 93.5

SNR, SINAD vs Input level, fIN = 2kHz

95 94 SNR SINAD SNR, SINAD (dBFS) 93 92 91

SNR, SINAD vs Reference Voltage, fIN = 2kHz

100 105 SNR HARMONICS, THD (dBFS) 110 115 120 125 130 135 140 145 SINAD

THD, Harmonics vs Reference Voltage, fIN = 2kHz

THD 2ND 3RD

93.0 40

30

20 10 INPUT LEVEL (dB)

0
236816 G07

90 2.5

4.5 REFERENCE VOLTAGE (V)

3.5

5
236816 G08

150 2.5

4 4.5 3.5 REFERENCE VOLTAGE (V)

5
236816 G09

236816f

LTC2368-16 TYPICAL PERFORMANCE CHARACTERISTICS

fSMPL = 1Msps, unless otherwise noted. SNR, SINAD vs Temperature, fIN = 2kHz
96.0 95.5 SNR, SINAD (dBFS) 95.0 94.5 94.0 93.5 93.0 55 35 15 SNR SINAD HARMONICS, THD (dBFS) 110 115 120 125 130 135 140 5 25 45 65 85 105 125 TEMPERATURE (C)
236816 G10

TA = 25C, VDD = 2.5V, OVDD = 2.5V, REF = 5V,

THD, Harmonics vs Temperature, fIN = 2kHz

1.0 THD 2ND INL/DNL ERROR (LSB) 0.5

INL/DNL vs Temperature

MAX INL MAX DNL 0 MIN DNL MIN INL 0.5

3RD

145 55 35 15

5 25 45 65 85 105 125 TEMPERATURE (C)

236816 G11

1.0 55 35 15

5 25 45 65 85 105 125 TEMPERATURE (C)

236816 G12

Full-Scale Error vs Temperature

10 8 FULL-SCALE ERROR (LSB) 6 OFFSET ERROR (LSB) 4 2 0 2 4 6 8 10 55 35 15 5 25 45 65 85 105 125 TEMPERATURE (C)
236816 G13

Offset Error vs Temperature

4 POWER SUPPLY CURRENT (mA) 3 2 1 0 1 2 3 4 55 35 15 5 25 45 65 85 105 125 TEMPERATURE (C)
236816 G14

Supply Current vs Temperature

6 IVDD 5 4 3 2 1 0 55 35 15 IOVDD

IREF

5 25 45 65 85 105 125 TEMPERATURE (C)

236816 G15

Shutdown Current vs Temperature

45 40 POWER-DOWN CURRENT (A) 35 30 25 20 15 10 5 0 55 35 15 5 25 45 65 85 105 125 TEMPERATURE (C)
236816 G16

CMRR vs Input Frequency

100 95 90 CMRR (dB) 85 80 75 70 REFERENCE CURRENT (mA) 0 100 200 300 FREQUENCY (kHz) 400 500
236816 G17

Reference Current vs Reference Voltage

0.6 0.5 0.4 0.3 0.2 0.1 0

IVDD + IOVDD + IREF

2.5

4.5 4 3.5 REFERENCE VOLTAGE (V)

5
236816 G18

236816f

LTC2368-16 PIN FUNCTIONS

CHAIN (Pin 1): Chain Mode Selector Pin. When low, the LTC2368-16 operates in normal mode and the RDL/SDI input pin functions to enable or disable SDO. When high, the LTC2368-16 operates in chain mode and the RDL/SDI pin functions as SDI, the daisy-chain serial data input. Logic levels are determined by OVDD. VDD (Pin 2): 2.5V Power Supply. The range of VDD is 2.375V to 2.625V. Bypass VDD to GND with a 10F ceramic capacitor. GND (Pins 3, 6, 10 and 16): Ground. IN+ (Pin 4): Analog Input. IN+ operates differential with respect to IN with an IN+-IN range of 0V to VREF. IN (Pin 5): Analog Ground Sense. IN has an input range of 100mV with respect to GND and must be tied to the ground plane or a remote ground sense. REF (Pins 7, 8): Reference Inputs. The range of REF is 2.5V to 5.1V. This pin is referred to the GND pin and should be decoupled closely to the pin with a 47F ceramic capacitor (X5R, 0805 size). CNV (Pin 9): Convert Input. A rising edge on this input powers up the part and initiates a new conversion. Logic levels are determined by OVDD. BUSY (Pin 11): BUSY Indicator. Goes high at the start of a new conversion and returns low when the conversion has finished. Logic levels are determined by OVDD. RDL/SDI (Pin 12): When CHAIN is low, the part is in normal mode and the pin is treated as a bus enabling input. When CHAIN is high, the part is in chain mode and the pin is treated as a serial data input pin where data from another ADC in the daisy chain is input. Logic levels are determined by OVDD. SCK (Pin 13): Serial Data Clock Input. When SDO is enabled, the conversion result or daisy-chain data from another ADC is shifted out on the rising edges of this clock MSB first. Logic levels are determined by OVDD. SDO (Pin 14): Serial Data Output. The conversion result or daisy-chain data is output on this pin on each rising edge of SCK MSB first. The output data is in straight binary format. Logic levels are determined by OVDD. OVDD (Pin 15): I/O Interface Digital Power. The range of OVDD is 1.71V to 5.25V. This supply is nominally set to the same supply as the host interface (1.8V, 2.5V, 3.3V, or 5V). Bypass OVDD to GND with a 0.1F capacitor. GND (Exposed Pad Pin 17, DFN Package Only): Ground. Exposed pad must be soldered directly to the ground plane.

236816f

LTC2368-16 FUNCTIONAL BLOCK DIAGRAM

VDD = 2.5V REF = 5V OVDD = 1.8V to 5V

IN+ IN

+
16-BIT SAMPLING ADC

SPI PORT

CHAIN SDO RDL/SDI SCK

CNV CONTROL LOGIC GND

236816 BD

BUSY

TIMING DIAGRAM
Conversion Timing Using the Serial Interface
CHAIN, RDL/SDI = 0 CNV

BUSY

CONVERT

POWER-DOWN AND ACQUIRE

SCK

SDO

D15 D14 D13 D12 D11 D10 D9 D8

D7 D6

D5 D4 D3

D2 D1

D0
236816 TD01

236816f

LTC2368-16 APPLICATIONS INFORMATION

OVERVIEW The LTC2368-16 is a low noise, low power, high speed 16-bit successive approximation register (SAR) ADC. Operating from a single 2.5V supply, the LTC2368-16 supports a 0V to VREF pseudo-differential unipolar input range with VREF ranging from 2.5V to 5.1V, making it ideal for high performance applications which require a wide dynamic range. The LTC2368-16 achieves 0.75LSB INL max, no missing codes at 16 bits and 94.7dB SNR. Fast 1Msps throughput with no cycle latency makes the LTC2368-16 ideally suited for a wide variety of high speed applications. An internal oscillator sets the conversion time, easing external timing considerations. The LTC2368-16 dissipates only 13.5mW at 1Msps, while an auto powerdown feature is provided to further reduce power dissipation during inactive periods. CONVERTER OPERATION The LTC2368-16 operates in two phases. During the acquisition phase, the charge redistribution capacitor D/A converter (CDAC) is connected to the IN+ and IN pins to sample the pseudo-differential analog input voltage. A rising edge on the CNV pin initiates a conversion. During the conversion phase, the 16-bit CDAC is sequenced through a successive approximation algorithm, effectively comparing the sampled input with binary-weighted fractions of the reference voltage (e.g. VREF/2, VREF/4 VREF/65536) using the differential comparator. At the end of conversion, the CDAC output approximates the sampled analog input. The ADC control logic then prepares the 16-bit digital output code for serial transfer. TRANSFER FUNCTION The LTC2368-16 digitizes the full-scale voltage of REF into 216 levels, resulting in an LSB size of 76V with REF = 5V. The ideal transfer function is shown in Figure2. The output data is in straight binary format.
111...111 111...110 111...101 OUTPUT CODE 111...100 1LSB = FS/65536

000...011 000...010 000...001 000...000 0V

UNIPOLAR ZERO

1 LSB

FS 1LSB INPUT VOLTAGE (V)

236816 F02

Figure 2. LTC2368-16 Transfer Function

ANALOG INPUT The analog inputs of the LTC2368-16 are pseudo-differential in order to reduce any unwanted signal that is common to both inputs. The analog inputs can be modeled by the equivalent circuit shown in Figure 3. The diodes at the input provide ESD protection. In the acquisition phase, each input sees approximately 45pF (CIN) from the sampling CDAC in series with 40 (RON) from the on-resistance of the sampling switch. The IN+ input draws a current spike while charging the CIN capacitor during acquisition. During conversion, the analog inputs draw only a small leakage current.
REF RON 40 CIN 45pF

IN+

REF IN RON 40

CIN 45pF

BIAS VOLTAGE

236816 F03

Figure 3. The Equivalent Circuit for the Differential Analog Input of the LTC2368-16

236816f

10

LTC2368-16 APPLICATIONS INFORMATION

INPUT DRIVE CIRCUITS A low impedance source can directly drive the high impedance input of the LTC2368-16 without gain error. A high impedance source should be buffered to minimize settling time during acquisition and to optimize the distortion performance of the ADC. Minimizing settling time is important even for DC inputs, because the ADC input draws a current spike when entering acquisition. For best performance, a buffer amplifier should be used to drive the analog input of the LTC2368-16. The amplifier provides low output impedance, which produces fast settling of the analog signal during the acquisition phase. It also provides isolation between the signal source and the current spike the ADC input draws. Input Filtering The noise and distortion of the buffer amplifier and signal source must be considered since they add to the ADC noise and distortion. Noisy input signals should be filtered prior to the buffer amplifier input with an appropriate filter to minimize noise. The simple 1-pole RC lowpass filter (LPF1) shown in Figure 4 is sufficient for many applications.
LPF1 VREF 0V 50 66nF BW = 48kHz

High quality capacitors and resistors should be used in the RC filters since these components can add distortion. NPO and silver mica type dielectric capacitors have excellent linearity. Carbon surface mount resistors can generate distortion from self heating and from damage that may occur during soldering. Metal film surface mount resistors are much less susceptible to both problems. Pseudo-Differential Unipolar Inputs For most applications, we recommend the low power LT6202 ADC driver to drive the LTC2368-16. With a low noise density of 1.9nV/Hz and a low supply current of 3mA, the LT6202 is flexible and may be configured to convert signals of various amplitudes to the 0V to 5V input range of the LTC2368-16. To achieve the full distortion performance of the LTC2368-16, a low distortion single-ended signal source driven through the LT6202 configured as a unity-gain buffer as shown in Figure 4 can be used to get the full data sheet THD specification of 118dB. The LT6202 can also be used to buffer and convert large true bipolar signals which swing below ground to the 0V to 5V input range of the LTC2368-16. Figure 5a shows the LT6202 being used to convert a 10V true bipolar signal for use by the LTC2368-16. In this case, the LT6202 is configured as an inverting amplifier stage, which acts to attenuate and level shift the input signal to the 0V to 5V input range of the LTC2368-16. In the inverting configuration, the single-ended input signal source no longer directly drives a high impedance input. The input impedance is instead set by resistor RIN. RIN must be chosen carefully based on the source impedance of the signal source. Higher values of RIN tend to degrade both the noise and distortion of the LT6202 and LTC2368-16 as a system. Table 1 shows the resulting SNR and THD for several values of RIN, R1, R2, R3 and R4 in this configuration. Figure 5b shows the resulting FFT when using the LT6202 as shown in Figure 5a.

+
LT6202

LPF2 10 10nF IN BW = 1.6MHz

236816 F04

IN+ LTC2368-16

Figure 4. Input Signal Chain

Another filter network consisting of LPF2 should be used between the buffer and ADC input to both minimize the noise contribution of the buffer and to help minimize disturbances reflected into the buffer from sampling transients. Long RC time constants at the analog inputs will slow down the settling of the analog inputs. Therefore, LPF2 requires a wider bandwidth than LPF1. A buffer amplifier with a low noise density must be selected to minimize degradation of the SNR.

236816f

11

LTC2368-16 APPLICATIONS INFORMATION

VCM = VREF/2 R2 499 10F R3 2k 10V 0V 10V RIN 2k 4 200pF

ADC REFERENCE
3

R4 402

+
LT6202 1

5V 0V

R1 499 200pF
236816 F05a

Figure 5a. LT6202 Converting a 10V Bipolar Signal to a 0V to 5V Input Signal

0 20 40 AMPLITUDE (dBFS) 60 80 SNR = 94.6dB THD = 99dB SINAD = 92.1dB SFDR = 99.6dB

The LTC2368-16 requires an external reference to define its input range. A low noise, low temperature drift reference is critical to achieving the full data sheet performance of the ADC. Linear Technology offers a portfolio of high performance references designed to meet the needs of many applications. With its small size, low power and high accuracy, the LTC6655-5 is particularly well suited for use with the LTC2368-16. The LTC6655-5 offers 0.025% (max) initial accuracy and 2ppm/C (max) temperature coefficient for high precision applications. The LTC6655-5 is fully specified over the H-grade temperature range and complements the extended temperature operation of the LTC2368-16 up to 125C. We recommend bypassing the LTC6655-5 with a 47F ceramic capacitor (X5R, 0805 size) close to the REF pin. The REF pin of the LTC2368-16 draws charge (QCONV) from the 47F bypass capacitor during each conversion cycle. The reference replenishes this charge with a DC current, IREF = QCONV/tCYC. The DC current draw of the REF pin, IREF, depends on the sampling rate and output code. If the LTC2368-16 is used to continuously sample a signal at a constant rate, the LTC6655-5 will keep the deviation of the reference voltage over the entire code span to less than 0.5LSBs. When idling, the REF pin on the LTC2368-16 draws only a small leakage current (< 1A). In applications where a burst of samples is taken after idling for long periods as shown in Figure 6, IREF quickly goes from approximately 0A to a maximum of 0.7mA at 1Msps. This step in DC current draw triggers a transient response in the reference that must be considered since any deviation in the reference output voltage will affect the accuracy of the output

100 120 140 160 180 0 100 200 300 FREQUENCY (kHz) 400 500

236816 F05b

Figure 5b. 32k Point FFT Plot with fIN = 2kHz for Circuit Shown in Figure 5a Table 1. SNR, THD vs RIN for 10V Input Signal
RIN () 2k 10k 100k R1 () 499 2.49k 24.9k R2 () 499 2.49k 24.9k R3 () 2k 10k 100k R4 () 402 2k 20k SNR (dB) 94.6 94.5 93.1 THD (dB) 99 94 93.8

CNV
236816 F06

IDLE PERIOD

IDLE PERIOD

Figure 6. CNV Waveform Showing Burst Sampling

236816f

12

LTC2368-16 APPLICATIONS INFORMATION

code. In applications where the transient response of the reference is important, the fast settling LTC6655-5 reference is also recommended. In applications where power management is critical and the external reference may be powered down, it is recommended that REF is kept greater than 2V in order to guarantee a maximum shutdown current of 140A. In such applications, a Schottky diode can be placed between REF and VDD, as shown in Figure 7.
REF VDD

the RMS amplitude of all other frequency components except the first five harmonics and DC. Figure 8 shows that the LTC2368-16 achieves a typical SNR of 94.7dB at a 1MHz sampling rate with a 2kHz input.
0 20 40 AMPLITUDE (dBFS) 60 80 100 120 140 160 180 0 100 200 300 FREQUENCY (kHz) 400 500
236816 F08

SNR = 94.7dB THD = 118dB SINAD = 94.7dB SFDR = 119dB

LTC2368-16

236816 F07

Figure 7. A Schottky Diode Between REF and VDD Maintains REF > 2V for Applications Where the Reference May Be Powered Down

Figure 8. 32k Point FFT with fIN = 2kHz of the LTC2368-16

Total Harmonic Distortion (THD) Total Harmonic Distortion (THD) is the ratio of the RMS sum of all harmonics of the input signal to the fundamental itself. The out-of-band harmonics alias into the frequency band between DC and half the sampling frequency (fSMPL/2). THD is expressed as: THD= 20log V22 + V32 + V42 ++ VN2 V1

DYNAMIC PERFORMANCE Fast Fourier Transform (FFT) techniques are used to test the ADCs frequency response, distortion and noise at the rated throughput. By applying a low distortion sine wave and analyzing the digital output using an FFT algorithm, the ADCs spectral content can be examined for frequencies outside the fundamental. The LTC2368-16 provides guaranteed tested limits for both AC distortion and noise measurements. Signal-to-Noise and Distortion Ratio (SINAD) The signal-to-noise and distortion ratio (SINAD) is the ratio between the RMS amplitude of the fundamental input frequency and the RMS amplitude of all other frequency components at the A/D output. The output is band-limited to frequencies from above DC and below half the sampling frequency. Figure 8 shows that the LTC2368-16 achieves a typical SINAD of 94.7dB at a 1MHz sampling rate with a 2kHz input. Signal-to-Noise Ratio (SNR) The signal-to-noise ratio (SNR) is the ratio between the RMS amplitude of the fundamental input frequency and

where V1 is the RMS amplitude of the fundamental frequency and V2 through VN are the amplitudes of the second through Nth harmonics. POWER CONSIDERATIONS The LTC2368-16 provides two power supply pins: the 2.5V power supply (VDD), and the digital input/output interface power supply (OVDD). The flexible OVDD supply allows the LTC2368-16 to communicate with any digital logic operating between 1.8V and 5V, including 2.5V and 3.3V systems. Power Supply Sequencing The LTC2368-16 does not have any specific power supply sequencing requirements. Care should be taken to adhere
236816f

13

LTC2368-16 APPLICATIONS INFORMATION

to the maximum voltage relationships described in the Absolute Maximum Ratings section. The LTC2368-16 has a power-on-reset (POR) circuit that will reset the LTC2368-16 at initial power-up or whenever the power supply voltage drops below 1V. Once the supply voltage re-enters the nominal supply voltage range, the POR will reinitialize the ADC. No conversions should be initiated until 20s after a POR event to ensure the reinitialization period has ended. Any conversions initiated before this time will produce invalid results. TIMING AND CONTROL CNV Timing The LTC2368-16 conversion is controlled by CNV. A rising edge on CNV will start a conversion and power up the LTC2368-16. Once a conversion has been initiated, it cannot be restarted until the conversion is complete. For optimum performance, CNV should be driven by a clean low jitter signal. Converter status is indicated by the BUSY output which remains high while the conversion is in progress. To ensure that no errors occur in the digitized results, any additional transitions on CNV should occur within 40ns from the start of the conversion or after the conversion has been completed. Once the conversion has completed, the LTC2368-16 powers down and begins acquiring the input signal. Internal Conversion Clock The LTC2368-16 has an internal clock that is trimmed to achieve a maximum conversion time of 527ns. With a minimum acquisition time of 460ns, throughput performance of 1Msps is guaranteed without any external adjustments. Auto Power-Down The LTC2368-16 automatically powers down after a conversion has been completed and powers up once a new conversion is initiated on the rising edge of CNV. During power down, data from the last conversion can be clocked out. To minimize power dissipation during power down, disable SDO and turn off SCK. The auto power-down feature will reduce the power dissipation of the LTC2368-16 as the sampling frequency is reduced. Since power is consumed only during a conversion, the LTC2368-16 remains powered down for a larger fraction of the conversion cycle (tCYC) at lower sample rates, thereby reducing the average power dissipation which scales with the sampling rate as shown in Figure 9.
6 POWER SUPPLY CURRENT (mA) 5 4 3 2 1 0 IVDD

IOVDD 1 200 400 600 800 SAMPLING RATE (kHz)

IREF 1000
236816 F09

Figure 9. Power Supply Current of the LTC2368-16 Versus Sampling Rate

DIGITAL INTERFACE The LTC2368-16 has a serial digital interface. The flexible OVDD supply allows the LTC2368-16 to communicate with any digital logic operating between 1.8V and 5V, including 2.5V and 3.3V systems. The serial output data is clocked out on the SDO pin when an external clock is applied to the SCK pin if SDO is enabled. Clocking out the data after the conversion will yield the best performance. With a shift clock frequency of at least 100MHz, a 1Msps throughput is still achieved. The serial output data changes state on the rising edge of SCK and can be captured on the falling edge or next rising edge of SCK. D15 remains valid till the first rising edge of SCK. The serial interface on the LTC2368-16 is simple and straightforward to use. The following sections describe the operation of the LTC2368-16. Several modes are provided depending on whether a single or multiple ADCs share the SPI bus or are daisy chained.
236816f

14

LTC2368-16 TIMING DIAGRAMS

Normal Mode, Single Device When CHAIN = 0, the LTC2368-16 operates in normal mode. In normal mode, RDL/SDI enables or disables the serial data output pin SDO. If RDL/SDI is high, SDO is in high impedance. If RDL/SDI is low, SDO is driven. Figure 10 shows a single LTC2368-16 operated in normal mode with CHAIN and RDL/SDI tied to ground. With RDL/SDI grounded, SDO is enabled and the MSB(D15) of the new conversion data is available at the falling edge of BUSY. This is the simplest way to operate the LTC2368-16.

CONVERT CNV CHAIN LTC2368-16 BUSY SDO SCK CLK DIGITAL HOST IRQ DATA IN

RDL/SDI

POWER-DOWN AND ACQUIRE CHAIN = 0 RDL/SDI = 0

CONVERT

POWER-DOWN AND ACQUIRE tCYC

CONVERT

tCNVH CNV tACQ = tCYC tCONV tBUSYLH BUSY tBUSYLH SCK tCONV tSCK tACQ tCNVL

tSCKH 2 tHSDO 3 tSCKL 14 15 16

tQUIET

tDSDOBUSYL SDO D15 D14

tDSDO D13 D1 D0
236816 F10

Figure 10. Using a Single LTC2368-16 in Normal Mode

236816f

15

LTC2368-16 TIMING DIAGRAMS

Normal Mode, Multiple Devices Figure 11 shows multiple LTC2368-16 devices operating in normal mode (CHAIN = 0) sharing CNV, SCK and SDO. By sharing CNV, SCK and SDO, the number of required signals to operate multiple ADCs in parallel is reduced. Since SDO is shared, the RDL/SDI input of each ADC must be used to allow only one LTC2368-16 to drive SDO at a time in order to avoid bus conflicts. As shown in Figure 11, the RDL/SDI inputs idle high and are individually brought low to read data out of each device between conversions. When RDL/SDI is brought low, the MSB of the selected device is output onto SDO.
RDLB RDLA CONVERT CNV LTC2368-16 B RDL/SDI SCK SDO CNV LTC2368-16 A RDL/SDI SCK DATA IN CLK

CHAIN

CHAIN

BUSY SDO

IRQ DIGITAL HOST

POWER-DOWN AND ACQUIRE CHAIN = 0 CNV

CONVERT

POWER-DOWN AND ACQUIRE

CONVERT

tCNVL tCONV

BUSY tBUSYLH RDL/SDIA

RDL/SDIB tSCK SCK 1 2 3 tHSDO SDO Hi-Z tEN D15A D14A tDSDO D13A D1A tDIS D0A Hi-Z D15B D14B D13B D1B D0B Hi-Z
236816 F11

tSCKH 14 15 16 tSCKL 17 18 19 30 31 32

tQUIET

Figure 11. Normal Mode With Multiple Devices Sharing CNV, SCK and SDO

236816f

16

LTC2368-16 TIMING DIAGRAMS

Chain Mode, Multiple Devices When CHAIN = OVDD, the LTC2368-16 operates in chain mode. In chain mode, SDO is always enabled and RDL/SDI serves as the serial data input pin (SDI) where daisy-chain data output from another ADC can be input. This is useful for applications where hardware constraints may limit the number of lines needed to interface to a large
CONVERT CNV LTC2368-16 SDO RDL/SDI B SCK CLK BUSY SDO SCK IRQ DATA IN

number of converters. Figure 12 shows an example with two daisy-chained devices. The MSB of converter A will appear at SDO of converter B after 16 SCK cycles. The MSB of converter A is clocked in at the SDI/RDL pin of converter B on the rising edge of the first SCK.

OVDD CHAIN RDL/SDI CNV LTC2368-16 A

OVDD CHAIN

DIGITAL HOST

POWER-DOWN AND ACQUIRE CHAIN = OVDD RDL/SDIA = 0

CONVERT

POWER-DOWN AND ACQUIRE

CONVERT

tCYC tCNVL

CNV

BUSY tCONV tBUSYLH tSCKCH SCK 1 2 3 tSSDISCK tHSDISCK SDOA = RDL/SDIB D15A tDSDOBUSYL SDOB D15B D14B D13B D1B D0B D15A D14A D1A D0A
236816 F12

tSCKH 16 17 18 tSCKL 30 31

tQUIET 32

14

15

tHSDO tDSDO D1A D0A

D14A

D13A

Figure 12. Chain Mode Timing Diagram

236816f

17

LTC2368-16 BOARD LAYOUT

To obtain the best performance from the LTC2368-16 a printed circuit board is recommended. Layout for the printed circuit board (PCB) should ensure the digital and analog signal lines are separated as much as possible. In particular, care should be taken not to run any digital clocks or signals alongside analog signals or underneath the ADC. Recommended Layout The following is an example of a recommended PCB layout. A single solid ground plane is used. Bypass capacitors to the supplies are placed as close as possible to the supply pins. Low impedance common returns for these bypass capacitors are essential to the low noise operation of the ADC. The analog input traces are screened by ground. For more details and information refer to DC1813A, the evaluation kit for the LTC2368-16.

Partial Top Silkscreen

236816f

18

LTC2368-16 BOARD LAYOUT

Partial Layer 1 Component Side

Partial Layer 2 Ground Plane

236816f

19

LTC2368-16 BOARD LAYOUT

Partial Layer 3 PWR Plane

Partial Layer 4 Bottom Layer

236816f

20

R1 33 +3.3V C2 0.1F +3.3V C3 0.1F 1 +3.3V R46 C56 0.1F 3 JP6 FS 1 2 3 +3.3V C13 0.8VREF 0.1F VREF R8 33 DC590 DETECT TO CPLD U3 NL17SZ74 5 3 DB17 DB16 J2 CON-EDGE 40-100 CLR\ Q\ PR\ Q 6 5 4 R4 7 33 4 CP GND 8 D VCC 2 +3.3V C4 0.1F 5 4 2 C11 0.1F R31 OPT V+ U15 5 LT6202CS5 +3.3V C7 0.1F C20 47F 6.3V 0805 4 9V TO 10V

+3.3V

C5 0.1F R3 CLK 33 TO CPLD 1 2 3 4 U4 NC7SVU04P5X 2 CNVST_33 FROM CPLD

R2 1k

+3.3V C1 0.1F

BOARD LAYOUT

J1 CLKIN

R5 49.9 1206

U2 R6 3 U8 3 NC7SZ04P5X NC7SVU04P5X 1k

U20 LTC6655AHMS8-5 8 SHDN GND 7 VIN OUT_F 6 GND OUT_S 5 GND GND

JP1 HD1X3-100

COUPLING AC DC

C18 OPT IN1 4 R45 C61 10F 6.3V VDD 2 OV DD 15 REF 7 8 REF 2 V

R15 OPT

R9 OPT

C42 15pF C58 OPT C9 10F 6.3V C10 0.1F

+2.5V

JP2 CM C55 1F V+ C57 0.1F V R35 OPT

Partial Schematic of Demoboard

3 6 10 16 1

GND GND GND GND

C8 1F

VREF/2

EXT C63 10F 6.3V C43 0.1F C44 1F C60 0.1F C59 1F 9V TO 10V

E7

EXT_CM

HD1X3-100

C46 1F

R40 OPT

COUPLING AC DC

JP5 HD1X3-100

J8 C49 OPT

AIN

R39 0

R41 OPT

C47 OPT C48 10F 6.3V

+
OUT1 1 HD1X3-100 U6 OPT NC7SZ66P5X 5 C39 CNV VCC 0.01F R16 9 2 B A 1 0 4 NPO CNV 13 SCK IN+ SCK OE 4 C65 14 SDO SDO OPT R19 LTC2368-16 GND 11 BUSY BUSY 0805 NPO 0 3 IN 12 RD 5 RDL/SDI R58 C40 OPT R7 +3.3V NPO 1k R38 U9 OPT C15 NC7SZ04P5X 5 0.1F 2 4 3 R17 R13 2k 1k J3 DC590 R10 4.99k SDO 1 3 5 7 9 11 13 2 4 6 8 10 12 14 U7 C14 0.1F 8 24LC025-I/ST VCC SCL SCK SDA WP CNV ARRAY A2 EEPROM A1 A0 VSS 4 6 5 7 3 2 1

AIN+

J4 3 +IN1 V+ R32 10 +2.5V

R14 0

C17 10F R32 0 C6 10F 6.3V DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15

CLKOUT C16 1 0.1F

39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1

40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2

R11 4.99k

R12 4.99k

236816 BL

LTC2368-16

21

236816f

LTC2368-16 PACKAGE DESCRIPTION

Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. DE Package 16-Lead Plastic DFN (4mm 3mm)

(Reference LTC DWG # 05-08-1732 Rev )

0.70 0.05 3.60 0.05 2.20 0.05 3.30 0.05 1.70 0.05 PACKAGE OUTLINE 0.25 0.05 0.45 BSC 3.15 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED

4.00 0.10 (2 SIDES) R = 0.05 TYP 3.00 0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) 0.200 REF 0.75 0.05

R = 0.115 TYP

0.40 0.10 16

3.30 0.10 1.70 0.10 PIN 1 NOTCH R = 0.20 OR 0.35 45 CHAMFER 1 0.23 0.05 0.45 BSC 3.15 REF
(DE16) DFN 0806 REV

0.00 0.05

BOTTOM VIEWEXPOSED PAD

NOTE: 1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WGED-3) IN JEDEC PACKAGE OUTLINE MO-229 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE

236816f

22

LTC2368-16 PACKAGE DESCRIPTION

Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MS Package 16-Lead Plastic MSOP

(Reference LTC DWG # 05-08-1669 Rev )

0.889 0.127 (.035 .005)

5.23 (.206) MIN

3.20 3.45 (.126 .136)

0.305 0.038 (.0120 .0015) TYP

0.50 (.0197) BSC

4.039 0.102 (.159 .004) (NOTE 3) 16151413121110 9

RECOMMENDED SOLDER PAD LAYOUT

DETAIL A 0 6 TYP

0.280 0.076 (.011 .003) REF

0.254 (.010)
GAUGE PLANE

4.90 0.152 (.193 .006)

3.00 0.102 (.118 .004) (NOTE 4)

0.53 0.152 (.021 .006)

DETAIL A

0.18 (.007)
SEATING PLANE

1.10 (.043) MAX

1234567 8

0.86 (.034) REF

NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX

0.17 0.27 (.007 .011) TYP

0.50 (.0197) BSC

0.1016 0.0508 (.004 .002)

MSOP (MS16) 1107 REV

236816f

Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

23

LTC2368-16 TYPICAL APPLICATION

LT6202 Converting a 10V Bipolar Signal to a 0V to 5V Input Signal Into the LTC2368-16
8V 5V 200pF R2 3k 5 V+ 3 47F LT6202 5V 1 4 0V 10 10nF V 2 10V 0V 10V RIN 2k R1 499 220pF
236816 TA02

LTC6655-5 VIN VOUT_F VOUT_S

R4 402

2.5V IN+ IN REF VDD

10F

R3 2k

LTC2368-16

3V

RELATED PARTS
PART NUMBER ADCs LTC2379-18/LTC2378-18 LTC2377-18/LTC2376-18 LTC2380-16/LTC2378-16 LTC2377-16/LTC2376-16 LTC2383-16/LTC238216/LTC2381-16 LTC2393-16/LTC239216/LTC2391-16 LTC2365 LTC2355-14/LTC2356-14 DACS LTC2641 LTC2630 References LTC6655 LTC6652 Amplifiers LT6202/LT6203 LT6200/LT6200-5/ LT6200-10 DESCRIPTION 18-Bit, 1.6Msps/1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 2Msps/1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 1Msps/500ksps/250ksps Serial, Low Power ADC 16-Bit, 1Msps/500ksps/250ksps Parallel/Serial ADC 12-Bit, 1Msps Serial ADC 14-Bit, 3.5Msps Serial ADC 16-Bit/14-Bit/12-Bit Single Serial VOUT DACs 12-Bit/10-Bit/8-Bit Single VOUT DACs Precision Low Drift Low Noise Buffered Reference Precision Low Drift Low Noise Buffered Reference Single/Dual 100MHz Rail-to-Rail Input/Output Noise Low Power Amplifiers 165MHz/800MHz/1.6GHz Op Amp with Unity Gain/AV = 5/AV = 10 COMMENTS 2.5V Supply, Differential Input, 101.2dB SNR, 5V Input Range, DGC, Pin-Compatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 2.5V Supply, Differential Input, 96.2dB SNR, 5V Input Range, DGC, Pin-Compatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 2.5V Supply, Differential Input, 92dB SNR, 2.5V Input Range, PinCompatible Family in MSOP-16 and 4mm 3mm DFN-16 Packages 5V Supply, Differential Input, 94dB SNR, 4.096V Input Range, PinCompatible Family in 7mm 7mm LQFP-48 and QFN-48 Packages 2.35V to 3.6V Supply, 6- and 8-Lead TSOT-23 Packages 3.3V Supply, 1-Channel, Unipolar/Bipolar, 18mW, MSOP-10 Package 1LSB INL/DNL, MSOP-8 Package, 0V to 5V Output SC70 6-Pin Package, Internal Reference, 1LSB INL (12 Bits) 5V/2.5V, 5ppm/C, 0.25ppm Peak-to-Peak Noise, MSOP-8 Package 5V/2.5V, 5ppm/C, 2.1ppm Peak-to-Peak Noise, MSOP-8 Package 1.9nVHz, 3mA Maximum, 100MHz Gain Bandwidth Low Noise Voltage: 0.95nV/Hz (100kHz), Low Distortion: 80dB at 1MHz, TSOT23-6 Package

236816f

24 Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507

LT 0112 PRINTED IN USA

www.linear.com

LINEAR TECHNOLOGY CORPORATION 2012