VHF FM TRANSCEIVER

TK-2107
SERVICE MANUAL
2000-05 PRINTED IN JAPAN B51-8536-00(S) 200

Antenna (T90-0733-05):M3

Knob (CHANNEL SELECTOR) (K29-5278-03)

Knob(VOLUME) (K29-5255-03)

CONTENTS
GENERAL .................................................................. 2 REALIGNMENT ......................................................... 2 DISASSEMBLY FOR REPAIR ................................... 4 CIRCUIT DESCRIPTION ........................................... 5 SEMICONDUCTOR DATA ......................................... 9 DESCRIPTION OF COMPONENTS ........................ 10 PARTS LIST ............................................................. 11 EXPLODED VIEW ................................................... 17 PACKING ................................................................. 18

Cabinet assy (A02-2448-13)

ADJUSTMENT......................................................... 19 PC BOARD VIEWS TX-RX UNIT (X57-6020-21) ................................ 23 SCHEMATIC DIAGRAM .......................................... 27 BLOCK DIAGRAM .................................................. 31 LEVEL DIAGRAM ................................................... 33 KNB-15A (Ni-Cd BATTERY) ................................... 34

TK-2107 (16 channels)

SPECIFICATIONS ................................ BACK COVER

TK-2107
GENERAL/REALIGNMENT
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced technicians familiar with similar types of commercial grade communications equipment. It contains all required service information for the equipment and is current as of the publication data. Changes which may occur after publication are covered by either Service Bulletins or Manual Revisions. These are issued as required.

PERSONAL SAFETY
The following precautions are recommended for personal safety : DO NOT transmit until all RF connectors are verified secure and any open connectors are properly terminated. SHUT OFF and DO NOT operate this equipment near electrical blasting caps or in an explosive atmosphere. This equipment should be serviced by a qualified technician only.

ORDERING REPLACEMENT PARTS

When ordering replacement parts or equipment information, the full part identification number should be included. This applies to all parts : components, kits, or chassis. If the part number is not known, include the chassis or kit number of which it is a part, and a sufficient description of the required component for proper identification.

SERVICE
This radio is designed for easy servicing. Refer to the schematic diagrams, printed circuit board views, and alignment procedures contained within. Destnation M3 Number of CH 16 RF power output 5W

REALIGNMENT
1 Modes
User Mode MODE User Mode PC Mode PC Mode Manufacture Mode

3 Getting acquainted PTT (Push-To-Talk) switch Press this switch, then speak into the microphone to call a station. Release the switch to receive. Monitor key Press and hold to monitor how busy the current channel is and to monitor signals being received that do not contain the matched QT/DQT code. Channel selector Rotate to select channels 1 ~ 16. LED indicator Lights red while transmitting, green while receiving a signal. Flashes red when the battery voltage is low while transmitting. Power switch/ Volume control Turn clockwise to switch the transceiver ON. Turn counterclockwise until a click sounds, to switch the transceiver OFF. Rotate to adjust the volume level.
Speaker

FUNCTION Use this mode for normal operation. Use this mode, to make various settings by means of the FPU through the RS-232C port. Manufacture Mode Use this mode, to realign the various settings through the RS-232C port during manufacture work.

2 How to enter each mode

MODE User Mode PC Mode PROCEDURE Power ON Connect to the IBM PC compatible machine and controled by the FPU.
Antenna Microphone

Speaker/ microphone jacks

TK-260

:K, K2

TK-2107
REALIGNMENT
PC MODE
Preface
The transceiver is programmed by using a personal computer, programming interface (KPG-22) and programming software (KPG-55D). The programming software can be used with an IBM PC or compatible. Figure 1 shows the setup of an IBM PC for programming.

KPG-22 description
(PC programming interface cable: Option) The KPG-22 is required to interface the TK-2107 with the computer. It has a circuit in its D-subconnector (25-pin) case that converts the RS-232C Iogic level to the TTL Ievel. The KPG-22 connects the side panel jacks of the TK-2107 to the computer's RS-232C serial port.

Connenction procedure
1. Connect the TK-2107 to the personal computer with the interface cable. 2. When data is transmitting from the transceiver the red LED lights. When data is receiving by the transceiver the green LED lights.

Programming software description

The KPG-55D Programming Disk is supplied in 3-1/2" the disk format. The Software on this disk allows a user to program TK-2107 radios via a Programming interface cable (KPG-22).

Programming with IBM PC

If data is transferred to the transceiver from an IBM PC with the KPG-55D, the destination data (basic radio information) for each set can be modified. Normally, it is not necessary to modify the destination data because their values are determined automatically when the frequency range (frequency type) is set. The values should be modified only if necessary. Data can be programmed into the EEPROM in RS-232C format via the SP MIC plug. In this mode the PTT Iine operates as TXD and RXD data lines respectively. M3 type has wide mode only. All narrow data should be not available, even thouth data would be modified in test mode.

Notes:
The data stored in the personal computer must match the Model Name when it is written into the EEPROM. Do not press the [PTT] key during data transmission or reception.

IBM-PC

KPG-22

KPG-55D

Gray

RF Power meter or SSG Tuning cable (E30-3216-05)

Gray/Black 1.5D-XV Lead wire + 1.5D-XV Shield wire -

} }

SP

MIC

Fig. 1

TK-260

:K, K2

TK-2107
DISASSEMBLY FOR REPAIR
Separating the case assembly from the chassis
1. Remove the two knobs and three round nuts . 2. Remove the two screws . 3. Expand the right and left sides of the bottom of the case assembly, Iift the chassis, and remove it from the case assembly .

Separating the chassis from the unit

1. Remove the eleven screws . 2. Remove the solder from the antenna terminal using a soldering iron then lift the unit off . 3. Remove the two screws and remove the antenna connector. Note : When reassembling the unit in the chassis, be sure to solder the antenna terminal.

Antenna terminal

4. Taking care not to cut the speaker lead and case assembly.

, open the chassis

Removing the lever

1. Raise the lever on the lower case , insert a small flat screwdriver into the space between the case and lever, open the case carefully and lift the lever off. Note : Do not force to separate the case from the lever.

Lever knob Cace assembly

TK-260

:K, K2

TK-2107
CIRCUIT DESCRIPTION
1. Frequency configuration
The receiver utilizes double conversion. The first IF is 38.85MHz and the second IF is 450kHz. The first local oscillator signal is supplied from the PLL circuit.
ANT

The PLL circuit in the transmitter generates the necessary frequencies. Fig. 1 shows the frequencies.
CF 450kHz

MCF ANT SW RF AMP 38.85MHz IF SYSTEM 38.4MHz X3 multiply AF AMP SP

TCXO

12.8MHz

RX PA AMP TX AMP PLL VCO TX MIC AMP MIC

Fig. 1 Frequency configuration

2. Receiver
The receiver is double conversion superheterodyne, designed to operate in the frequency range of 216 to 223MHz (M3 type). The frequency configuration is shown in Fig. 1.

1) Front - end RF amplifier

An incoming signal from the antenna is applied to an RF amplifier (Q203) after passing through a transmit/receive switch circuit (D102 and D103 are off) and a band pass filter (L208, L209 and L210). After the signal is amplified (Q203),
ANT BPF RF AMP Q203 BPF MIXER Q202 MCF XF200 IF AMP Q201 IF, MIX, DET IC200 AF AMP LPF, HPF IC300 AF PA AMP IC302

the signal is filtered through a band pass filter (L203 and L214) to eliminate unwanted signals before it is passed to the first mixer. (See Fig. 2)
CF200

D102, D103 ANT SW

SP

TCXO

X3 multiply Q1

1st Local OSC (PLL)

Fig. 2 Receiver section configuration 2) First Mixer

The signal from the RF amplifier is heterodyned with the first local oscillator signal from the PLL frequency synthesizer circuit at the first mixer (Q202) to create a 38.85MHz first intermediate frequency (1st IF) signal. The first IF signal is then fed through two monolithic crystal filters (MCFs : XF200) to further remove spurious signals.

4) AF amplifier
The recovered AF signal obtained from IC200 is amplified by IC300 (1/4), filtered by the IC300 low-pass filter (2/4) and IC300 high-pass filter (3/4) and (4/4), and de-emphasized by R303 and C306. The processed AF signal passes through an AF volume control and is amplified to a sufficient level to drive a loud speaker by an AF power amplifier (IC302).

3) IF amplifier
The first IF signal is amplified by Q201, and then enters IC200 (FM processing IC). The signal is heterodyned again with a second local oscillator signal within IC200 to create a 450kHz second IF signal. The second IF signal is then fed through a 450kHz ceramic filter (CF200) to further eliminate unwanted signals before it is amplified and FM detected in TK-260 :K, K2 IC200. 5

TK-2107
CIRCUIT DESCRIPTION
XF200:L71-0535-05 Item Nominal center frequency Pass band width 40dB stop band width Ripple Insertion loss Guaranteed attenuation Terminal impedance Rating 38.850MHz 7.5kHz or more at 3dB 40.0kHz or less 1.0dB or less 3.0dB or less 80dB or more at fo -1000kHz 1200 / 1.4PF CF200:L72-0979-05 Item Nominal center frequency 6dB band width 50dB band width Ripple Insertion loss Guaranteed attenuation Terminal impedance Rating 450kHz 7.5kHz or more 15kHz or less 2.0dB or less at fo 5kHz 6.0dB or less 35.0dB or more at fo 100kHz 1.5 k

5) Squelch
Part of the AF signal from the IC enters the FM IC again, and the noise component is amplified and rectified by a filter and an amplifier to produce a DC voltage corresponding to the noise level. The DC signal from the FM IC goes to the analog port of the microprocessor (IC403). IC403 determines whether to output
FM IF IC IC200 IF AMP DET IC300 AF AMP LPF HPF Q302 SW IC302 AF PA AMP Q307 SW SP

sounds from the speaker by checking whether the input voltage is higher or lower than the preset value. To output sounds from the speaker, IC403 sends a high signal to the MUTE and AFCO Iines and turns IC302 on through Q302, Q304, Q305, Q306 and Q307.(See Fig. 3)

DET

HPF AMP Q304, 305, 306 SW

IC301 LPF

67

62

QT/DQT

MUTE

BUSY

AFCO

TI

Q303 W/N SW

IC403 MPU

Fig. 3 AF Amplifier and squelch

6) Receive signaling
QT/DQT 300 Hz and higher audio frequencies of the output signal from IF IC are cut by a low-pass filter (IC301). The resulting signal enters the microprocessor (IC403). IC403 determines whether the QT or DQT matches the preset value, and controls the MUTE and AFCO and the speaker output sounds according to the squelch results.

3. PLL frequency synthesizer

The PLL circuit generates the first local oscillator signal for reception and the RF signal for transmission.

1) PLL
The frequency step of the PLL circuit is 5 or 6.25kHz. A 12.8MHz reference oscillator signal is divided at IC1 by a fixed counter to produce the 5 or 6.25kHz reference frequency. The voltage controlled oscillator (VCO) output signal is buffer amplified by Q6, then divided in IC1 by a dual-module programmable counter . The divided signal is compared in phase with the 5 or 6.25kHz reference signal in the phase comparator in IC1. The output signal from the phase comparator is filtrered through a low-pass filter and passed to the VCO to control the oscillator frequency. (See Fig.4)

TK-260

:K, K2

TK-2107
CIRCUIT DESCRIPTION
2) VCO
The operating frequency is generated by Q4 in transmit mode and Q3 in receive mode. The oscillator frequency is controlled by applying the VCO control voltage, obtained from the phase comparator, to the varactor diodes (D2 and D4 in transmit mode and D1 and D3 in receive mode). The T/R pin is
PLL IC IC1 Q4 TX VCO

set high in receive mode causing Q5 and Q7 to turn Q4 off, and turn Q3 on . The T/R pin is set low in transmit mode. The outputs from Q3 and Q4 are amplified by Q6 and sent to the buffer amplifiers.

D1, 2 5kHz/6.25kHz I/N LPF PLL DATA PHASE COMPARATOR REF OSC I/M 5kHz/6.25kHz CHARGE PUMP D3, 4

Q2 RF AMP

Q6 BUFF AMP

Q3 RX VCO Q5, 7 T/R SW

12.8MHz

Fig. 4 PLL circuit

5C

3) UNLOCK DETECTOR
If a pulse signal appears at the LD pin of IC1, an unlock condition occurs, and the DC voltage obtained from D7, R6, and C1 causes the voltage applied to the UL pin of the microprocessor to go low. When the microprocessor detects this condition, the transmitter is disabled, ignoring the push-totalk switch input signal. (See Fig.5)
IC1 D7 LD PLL IC C1 UL MPU R6 IC403

Fig. 5 Unlock detector circuit

4. Transmitter
1) Transmit audio
The modulation signal from the microphone is amplified by IC500 (1/2), passes through a preemphasis circuit, and amplified by the other IC500 (1/2) to perform IDC operation. The signal then passes through a low-pass filter (splatter fiIter) (Q501 and Q502) and cuts 3kHz and higher frequencies. The resulting signal goes to the VCO through the VCO modulation terminal for direct FM modulation. (See Fig. 6)
IC500 (1/2) MIC AMP MIC

2) QT/DQT encoder
A necessary signal for QT/DQT encoding is generated by IC403 and FM-modulated to the PLL reference signal. Since the reference OSC does not modulate the loop characteristic frequency or higher, modulation is performed at the VCO side by adjusting the balance. (See Fig. 6)

PREEMPHASIS

IC500 (1/2) IDC

Q501, 502 LPF (SPLATTER FILTER)

VR501 MAX DEV

D5, Q4 VCO

Q503 SW IC403 TO MUTE QT/DQT

BALANCE X1, IC1 REFERENCE OSC (TCXO)

Fig. 6 Transmit audio QT/DQT

TK-260 :K, K2

TK-2107
CIRCUIT DESCRIPTION
3) VCO and RF amplifier
The transmit signal obtained from the VCO buffer amplifier Q100, is amplified by Q101. This amplified signal is passed to the power amplifier, Q102 and Q105, which consists of a 2stage FET amplifier and is capable of producing up to 5W of RF power. (See Fig.7)

4) ANT switch and LPF

The RF amplifier output signal is passed through a lowpass filter network and a transmit/receive switching circuit before it is passed to the antenna terminal. The transmit/ receive switching circuit is comprised of D101, D102 and D103. D102 and D103 turned on (conductive) in transmit mode and off (isolated) in receive mode.
ANT

AMP Q101

DRIVE AMP Q102

FINAL AMP Q105

ANT SW D101

LPF

5T

APC DET Q109 SW IC100 Q103, Q104 B SW ANT SW B 5T Q106 D102,103

SW

APC

Q108 TH100 SW

RX

5T

SW Q107

5T

Fig. 7 APC system

5) APC
The automatic power control (APC) circuit stabilizes the transmitter output power at a predetermined level by sensing the drain current of the final amplifier Field Effect Transistor (FET) . The voltage comparator, IC100 (2/2), compares the voltage obtained from the above drain current with a reference voltage which is set using the microprocessor. An APC voltage proportional to the difference between the sensed voltage and the reference voltage appears at the output of IC100 (1/2). This output voltage controls the gate of the FET power amplifier, which keeps the transmitter output power constant. The transmitter output power can be varied by the microprocessor which in turn changes the reference voltage and hence, the output power.

5. Power supply
A 5V reference power supply [5M] for the control circuit is derived from an internal battery. This reference is used to provide a 5V supply in transmit mode [5T], a 5V supply in receive mode [5R], and a 5V supply common in both modes [5C] based on the control signal sent from the microprocessor.

6. Control system
The IC403 CPU operates at 7.37MHz . This oscillator has a circuit that shifts the frequency according to the EEPROM data.

6) Terminal protection circuit

When the thermistor (TH100) reaches about 80C, the protection circuit turns on Q107 to protect transmitting final amplifier (Q105) from the over heating.
TK-260 :K, K2

TK-2107
SEMICONDUCTOR DATA
Microprocessor: M38267M8L241GP (IC403)
Pin No. I/O
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 TK-260 58 O O I I I I l l O O I I l l O O l I O I l I I I I I l l l l l l I I O l O I O O O O l l I l l/O O I l I I l I O O O :K, K2 O

Port Name
VC1 VC2 NC TIBI TI BUSY BATT NC VCCN APC NC NC NC NC BEEP TO NC PTT TXD RXD NC SELF MONl NC NC NC NC ENC3 ENC2 ENC1 ENC0 INTO RST NC NC XIN XOUT VSS SHIFT PABC WNRC WNTC NC NC NC NC SDA SCL UL NC NC NC NC NC DT CK NC LE

Function
Variable capacity tune control Variable capacity tune control NC QT/DQT external circuit center point input QT/DQT signal input Busy input Battery voltage detection NC Frequency regulation output TX : Auto power control D/A output RX : BPF tuning D/A output NC NC NC NC Beep output QT/DQT output NC [PTT] key input Connected to RXD RS-232C output Connected to SP/ MIC test(REM) RS-232C input Connected to [PTT] line NC Self program L : disable [MONl] key input NC NC NC NC Encode input (channel select) Encode input (channel select) Encode input (channel select) Encode input (channel select) Power detection control Reset input NC NC 7.3728MHz oscillator 7.3728MHz oscillator GND Beat shift H : shift on Final supply H : on Audio reference sensitivity L : narrow MAX Dev. Control Narrow: H NC NC NC NC EEPROM data line EEPROM clock line PLL unlock detection pin L : unlock NC NC NC NC NC Common data output Common clock output NC PLL IC enable H : Iatches

Pin No. I/O

59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O l l l O O O O I l I I I

Port Name
NC NC 5MC AFCO RX GLED RLED SAVE MUTE 5RC 5TC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC VCC VREF AVSS NC NC NC NC NC NC NC NC NC

Function
NC NC Control of power supply (5M) for everything except the microcomputer and EEPROM L : Power supply ON AF amp power suppIy H : ON TX/RX VCO select H : RX Green LED control H : Lit RED LED control H : Lit Save control H : Save off Mute control H : Mic mute L : AF mute Reception power suppIy control L : on Transmission power suppIy control H : on NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC NC Microcomputer power supply, 5V input A/D conversion reference voltage ; connected to Vcc A/D converter power supply ; connected to Vss NC NC NC NC NC NC NC NC NC

FET : 2SK2596(Q102)
Absolute Maximum Ratings (Ta=25C) Item Rating VDSS 17V VGSS 10V ID 0.4A Pch* Tch Tstg 3W 150C -45~+150C *Tc=25C

FET : 2SK2595(Q105)
Absolute Maximum Ratings (Ta=25C) Item Rating VDS 17V VGSS 10V ID 1.1A Pch* Tch Tstg 20W 150C -45~+150C *Tc=25C

TK-2107
DESCRIPTION OF COMPONENTS
TK-2107
Ref No.
IC1 IC100 IC200 IC300 IC301 IC302 IC400 IC401 IC402 IC403 IC404 IC500 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q100 Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108-200 Q201 Q202 Q203 Q300 Q302 Q304-306 Q307 Q400-402 Q403 Q404 Q405 Q406-408 Q500 Q501,502 Q503 Q504 IC IC IC IC IC IC IC IC IC IC IC IC TRANSISTOR TRANSISTOR FET FET FET TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET FET TRANSISTOR FET FET TRANSISTOR

Semiconductor

Description
PHASE LOCKED LOOP SYSTEM AUTOMA POWER CONTROL TIC IF SYSTEM AUDIO AMP ACTIVE FILTER ACTIVE FILTER AUDIO POWER AMP RESET SWITCH EEPROM VOLTAGE DETECT MICRO PROCESSOR VOLTAGE REGULATER MIC AMP/LIMITER TRIPLER RF AMP VCO RX VCO TX DC SWITCH RF BUFFER AMP DC SWITCH RIPPLE FILTER RF AMP TX PRE-DRIVE TX DRIVE DC SWITCH DC SWITCH TX FINAL DC SWITCH TEMPERATURE PROTECTION SWITCH DC SWITCH IF AMP MIXER MIXER RF AMP ACTIVE FILTER AUDIO MUTE SWITCH DC SWITCH AUDIO MUTE SWITCH DC SWITCH BEAT SHIFT SWITCH DC SWITCH DC SWITCH DC SWITCH DC SWITCH ACTIVE FILTER MIC MUTE/ AGC DC SWITCH FREQ. CONTROL TX MODULATION CURRENT STEERING UNLOCK DETECT RF SWITCH ANTENNA SWITCH RF SWITCH LIMITER TX BUSY AGC DETECT MIC MUTE/AGC SWITCH REVERSE PROTECTION

TRANSISTOR TRANSISTOR FET FET TRANSISTOR FET TRANSISTOR FET TRANSISTOR TRANSISTOR TRANSISTOR FET TRANSISTOR FET TRANSISTOR TRANSISTOR TRANSISTOR VARIABLE CAPACITANCE D1-4 DIODE VARIABLE CAPACITANCE D5 DIODE D6 DIODE D7 DIODE D100 DIODE D101-103 DIODE D200 DIODE D300 DIODE D400 LED D401 LED D500 DIODE D501 DIODE TK-260 D502K2 DIODE :K,

10

TK-2107
PARTS LIST
New Parts. indicates safety critical components. Parts without Parts No. are not supplied. Les articles non mentionnes dans le Parts No. ne sont pas fournis. Teile ohne Parts No. werden nicht geliefert.

TK-2107
Ref. No. Address parts
New

Parts No.

Description

Destination

Ref. No. Address parts

C7 C8 C9 C10 C12 C14 C15 C16 C17 C18 C19,20 C23 C24 C25 C26 C27 C28 C29-31 C32 C33 C34 C35 C36 C37 C38 C39 C40,41 C42 C43,44 C45,46 C47 C48 C49 C50 C51 C100 C101,102 C103 C104-107 C108 C109 C110 C111,112 C113 C114-116 C118-120 C121 C122 C123 C124 C125 C126 C127

New

Parts No.
CK73GB1H102K CK73FB1C224K CC73GCH1H100D CC73GCH1H470J CK73FB1C224K CC73GCH1H100D C92-0565-05 CC73GCH1H680J CK73GB1H331K C92-0504-05 CK73GB1H103K C92-0560-05 CK73GB1H681K CK73GB1H471K CC73GCH1H121J CK73GB1H102K CC73GCH1H330J CK73GB1H102K CC73GCH1H180J CC73GCH1H120J CC73GCH1HR75B CC73GCH1H060D CC73GCH1H120J CC73GCH1H050B CC73GCH1H150J CK73GB1H103K CK73GB1H102K CK73GB1H103K CC73GCH1H0R5B CK73GB1H102K CC73GCH1H330J CC73GCH1H100D CK73GB1H102K C92-0507-05 CC73GCH1H680J CC73GCH1H150J CK73GB1H102K CC73GCH1H220J CK73GB1H102K CC73GCH1H120J CK73GB1H102K CK73GB1C104K CK73GB1H102K CC73GCH1H390J CK73GB1H102K CK73GB1H102K CK73EB1C105K CC73GCH1H050C CK73GB1H103K CK73GB1H102K CK73GB1C104K CC73GCH1H330J C92-0565-05 CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP-TAN CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN

Description
1000PF 0.22UF 10PF 47PF 0.22UF 10PF 6.8UF 68PF 330PF 0.68UF 0.010UF 10UF 680PF 470PF 120PF 1000PF 33PF 1000PF 18PF 12PF 0.75PF 6.0PF 12PF 5.0PF 15PF 0.010UF 1000PF 0.010UF 0.5PF 1000PF 33PF 10PF 1000PF 4.7UF 68PF 15PF 1000PF 22PF 1000PF 12PF 1000PF 0.10UF 1000PF 39PF 1000PF 1000PF 1.0UF 5.0PF 0.010UF 1000PF 0.10UF 33PF 6.8UF K K D J K D 10WV J K 20WV K 6.3WV K K J K J K J J B D J B J K K K B K J D K 6.3WV J J K J K J K K K J K K K C K K K J 10WV

Destination

TK-2107
1 2 3 5 6 7 8 9 10 1A 3B 3D 2B 3B 1A 2B 2B 11 12 13 14 15 16 17 18 19 20 21 2B 2A 2A 1C 1C 2D 3C 1A 2B 3D 3B A02-2448-13 A82-0034-03 B09-0351-03 B72-1847-04 E04-0413-05 E23-1006-04 G01-0881-04 G11-2583-04 G11-2588-04 G13-1709-04 G13-1763-04 G53-0791-03 G53-0842-13 G53-0860-04 H12-3037-02 H25-0085-04 H25-2012-04 H52-1522-02 J19-1572-04 J19-5344-03 J21-4493-04 J29-0624-03 J82-0059-05 K29-5255-03 K29-5274-03 K29-5275-13 K29-5278-03 K29-5337-03 N09-2319-05 N14-0581-04 N14-0582-14 N30-2606-46 N79-2035-46 N83-2005-46 N99-0396-05 R31-0624-05 S60-0410-05 SP ANT 1A 2C T07-0369-05 T90-0733-05 CABINET ASSY REAR PANEL CAP MODEL NAME PLATE RF COAXIAL RECEPTACLE(SMA) RELAY TERMINAL(BATT -) COIL SPRING(BATT RELEASE) SHEET RUBBER SHEET(CHASSIS) CUSHION(VOL) CUSHION(CHASSIS-BATT) PACKING(SP/MIC PLUG) PACKING(SPEAKER) PACKING(SIDE) PACKING FIXTURE PROTECTION BAG (100/200/0.07) PROTECTION BAG (75/100/0.08) ITEM CARTON CASE HOLDER(BATT RELEASE) HOLDER(VOL/CH S.W) SP/MIC HOLDER BELT HOOK FPC KNOB(VOL) BUTTON KNOB(MONI) BUTTON KNOB(PTT) KNOB(CH S.W) LEVER KNOB(BATT RELEASE) BINDING HEAD SCREW(SMA) CIRCULAR NUT(VOL/CH S.W) CIRCULAR NUT(SMA) PAN HEAD MACHINE SCREW PAN HEAD TAPTITE SCREW PAN HEAD TAPTITE SCREW SCREW SET VARIABLE RESISTOR ROTARY SWITCH SPEAKER HELICAL ANTENNA

22 23 24 25 26 A B C D E F G

1B 1A 1A 1B 1A 2B 1B 1B 3A 3B 2A.2B 3D

TX-RX UNIT (X57-6020-21)

D400 D401 C1 C2,3 C4 C5 C6 B30-2156-05 B30-2157-05 CK73GB1C104K CC73GCH1H101J CK73GB1C104K C92-0507-05 CC73GCH1H101J LED(RED) LED(YELLOW) CHIP C CHIP C CHIP C CHIP-TAN CHIP C 0.10UF 100PF 0.10UF 4.7UF 100PF K J K 6.3WV J

11

TK-2107
PARTS LIST
TX-RX UNIT (X57-6020-21)
Ref. No.
C128 C129 C130,131 C132 C133 C134 C135 C136 C137 C138 C139 C140 C141 C142 C143 C144 C146 C147 C148 C200 C201 C202 C203 C204 C205,206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C217 C218 C219 C220 C221 C222 C224,225 C235 C236 C237 C241 C243 C245,246 C248 C250,251 C254 C257 C258 C261 C300 C301 C302,303
New Address parts

TX-RX UNIT (X57-588X-XX)

Description
CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C 3.0PF 4.5PF 1000PF 470PF 1000PF 100PF 27PF 7.0PF 1000PF 5.0PF 1000PF 5.0PF 470PF 13PF 6.0PF 4.0PF 13PF 5.0PF 3.0PF 10UF 0.010UF 10PF 470PF CHIP C 220PF 0.10UF 27PF 0.10UF 0.010UF 0.10UF 15PF 0.10UF 0.010UF 3.5PF 0.010UF 1000PF 12PF 1000PF 0.010UF 4.0PF 0.10UF 0.10UF 1000PF 12PF 12PF 2.0PF 1000PF 13PF 1000PF 1.0PF 1.5PF 18PF 39PF 8200PF 0.018UF 0.10UF C B K K K J J D K C K C K J D C J C C 6.3WV K D K 4700PFK J K J K K K J K K B K K J K K C K K K G G C K J K C C J J K K K

Parts No.
CC73GCH1H030C CC73GCH1H4R5B CK73GB1H102K CK73GB1H471K CK73GB1H102K CC73GCH1H101J CC73GCH1H270J CC73GCH1H070D CK73GB1H102K CC73GCH1H050C CK73GB1H102K CC73GCH1H050C CK73GB1H471K CC73GCH1H130J CC73GCH1H060D CC73GCH1H040C CC73GCH1H130J CC73GCH1H050C CC73GCH1H030C C92-0560-05 CK73GB1H103K CC73GCH1H100D CK73GB1H471K CK73GB1H472K CC73GCH1H221J CK73GB1C104K CC73GCH1H270J CK73GB1C104K CK73GB1H103K CK73GB1C104K CC73GCH1H150J CK73GB1C104K CK73GB1H103K CC73GCH1H3R5B CK73GB1H103K CK73GB1H102K CC73GCH1H120J CK73GB1H102K CK73GB1H103K CC73GCH1H040C CK73GB1C104K CK73GB1C104K CK73GB1H102K CC73GCH1H120G CC73GCH1H120G CC73GCH1H020C CK73GB1H102K CC73GCH1H130J CK73GB1H102K CC73GCH1H010C CC73GCH1H1R5C CC73GCH1H180J CC73GCH1H390J CK73GB1H822K CK73GB1E183K CK73GB1C104K

Destination

Ref. No.
C304 C305 C306 C307 C308 C309 C311 C312 C313 C314 C316 C318 C319 C320,321 C322 C327 C330 C331 C332 C333 C334 C335 C336 C337 C338 C400 C402-404 C406,407 C408 C409 C410 C411 C412 C413,414 C415 C416 C417 C418 C420-422 C423 C424 C425 C427 C429,430 C500,501 C502 C503 C504 C505 C507 C508 C509 C510 C511 C512 C513

New Address parts

Parts No.
C92-0560-05 CK73GB1H103J CK73GB1C473K C92-0560-05 CK73GB1H562K CK73GB1H103J C92-0560-05 CK73GB1H103J CK73FB1A105K CK73GB1H102K CK73GB1H103J CK73GB1C333K CK73GB1C473K CK73GB1C333J CK73FB1E104K CK73GB1C104K CC73GCH1H101J CK73FB1C474K C92-0560-05 CK73GB1A474K CC73GCH1H221J CK73GB1C473K CK73GB1H103K C92-0665-05 CC73GCH1H560J CK73GB1C104K CK73GB1H102K CK73GB1H102K C92-0560-05 CC73GCH1H030C CK73GB1H102K CK73GB1H471K CC73GCH1H100D CK73GB1H102K CC73GCH1H100D CK73GB1H102K CK73EF1C105Z CK73GB1H103K CK73GB1H103K CK73GB1C104K CK73FB1A105K CK73GB1H103K CK73GB1H102K CK73FB1A105K CK73GB1C273K CK73GB1H392K CK73GB1C333K C92-0507-05 CK73FB1A105K C92-0587-05 CK73GB1H103K CK73GB1H332K CC73GCH1E821J CK73GB1C473K CK73GB1H332K CC73GCH1E681J CHIP-TAN CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C TANTAL CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP C CHIP C CHIP C

Description
10UF 0.010UF 0.047UF 10UF 5600PF 0.010UF 10UF 0.010UF 1.0UF 1000PF 0.010UF 0.033UF 0.047UF 0.033UF 0.10UF 0.10UF 100PF 0.47UF 10UF 0.47UF 220PF 0.047UF 0.010UF 100UF 56PF 0.10UF 1000PF 1000PF 10UF 3.0PF 1000PF 470PF 10PF 1000PF 10PF 1000PF 1.0UF 0.010UF 0.010UF 0.10UF 1.0UF 0.010UF 1000PF 1.0UF 0.027UF 3900PF 0.033UF 4.7UF 1.0UF 2.2UF 0.010UF 3300PF 820PF 0.047UF 3300PF 680PF 6.3WV J K 6.3WV K J 6.3WV J K K J K K J K K J K 6.3WV K J K K 6.3WV J K K K 6.3WV C K K D K D K Z K K K K K K K K K K 6.3WV K 4WV K K J K K J

Destination

12

TK-2107
PARTS LIST
TX-RX UNIT (X57-6020-21)
Ref. No.
C514 C515 C516 C517 C518 C519 C520 C521 C522 C523 C524 C525 C526 C527 C528 C529 C530,531 C532 C533 TC1,2 TC201 CN400 J500 F500 34 2B
New Address parts

Parts No.
CK73GB1C473K CK73GB1H103K CC73GCH1H100D CK73GB1H102K CK73GB1E223J C92-0507-05 CK73GB1E223J CK73GB1H102K CK73FB1E104K C92-0587-05 CK73GB1C273K CK73GB1C104K CK73GB1H471K C92-0560-05 CK73GB1H102K CK73FB1H102K CC73GCH1H221J CK73GB1H471K CK73GB1C104K C05-0383-05 C05-0370-05 E23-1005-04 E40-5998-05 E11-0457-05 F53-0130-05 G53-0862-04 J19-1571-04 J30-1249-04 L72-0979-05 L92-0140-05 L40-1005-85 L40-4781-86 L40-5681-86 L40-6891-86 L92-0140-05 L40-6891-86 L33-0750-05 L33-0744-05 L40-8275-77 L92-0140-05 L40-6891-86 L40-2285-38 L40-1085-77 L40-6875-77 L92-0140-05 L40-1875-77 L40-1098-76 L92-0149-05 L40-3363-77 L40-1575-54 L34-4548-05 L92-0149-05 L34-4650-05 L40-1095-85 L34-4550-05 L34-4548-05 CHIP C CHIP C CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP-TAN CHIP C CHIP C CHIP C CHIP-TAN CHIP C

Description
0.047UF 0.010UF 10PF 1000PF 0.022UF 4.7UF 0.022UF 1000PF 0.10UF 2.2UF 0.027UF 0.10UF 470PF 10UF 1000PF K K D K J 6.3WV J K K 4WV K K K 6.3WV K

Destination

Ref. No.
L115 L117 L118 L200 L201 L202 L203 L204 L208-210 L212 L212 L214 L400 L401 L402,403 L500 L501,502 X1 X400 XF200

New Address parts

Parts No.
L34-4549-05 L34-4548-05 L40-1092-81 L40-8285-85 L40-1085-85 L40-2285-38 L41-3378-03 L40-3988-76 L41-3378-03 L34-4554-05 L34-4585-05 L41-3378-03 L40-2281-86 L92-0140-05 L40-2281-86 L92-0140-05 L92-0149-05 L77-1756-05 L77-1761-05 L71-0535-05 N78-2640-46

Description
AIR-CORE COIL AIR-CORE COIL SMALL FIXED INDUCTOR SMALL FIXED INDUCTOR(0.82U) SMALL FIXED INDUCTOR(0.10U) SMALL FIXED INDUCTOR(220NH) SMALL FIXED INDUCTOR SMALL FIXED INDUCTOR(0.39UH) SMALL FIXED INDUCTOR COIL COIL SMALL FIXED INDUCTOR SMALL FIXED INDUCTOR(0.22U) FERRITE CHIP SMALL FIXED INDUCTOR(0.22U) FERRITE CHIP FERRITE CHIP TCXO (12.8MHZ) CRYSTAL RESONATOR(7.3728MHZ) MCF (38.85MHZ) PAN HEAD TAPTITE SCREW MULTI-COMP CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R 1K X4 150K J 1/16W 1.0K J 1/16W 10 J 1/16W 1.0K J 1/16W 0 OHM 1.0K J 1/16W 0 OHM 330K J 1/16W 1.0K J 1/16W 150 47K 270K 150 100 10K 68K 100K 270 47K 1.0K 100K 270 120K 100K 680 4.7K 1.0K 0 OHM 3.3K 12K 220 1.0K 100 3.3K J J J J J J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

Destination

CHIP C 1000PF K CHIP C 220PF J CHIP C 470PF K CHIP C 0.10UF K CERAMIC TRIMMER CAP(6P) CERAMIC TRIMMER CAP RELAY TERMINAL PIN ASSY PHONE JACK (2.5/3.5D) FUSE PACKING HOLDER SPACER CERAMIC FILTER FERRITE CHIP SMALL FIXED INDUCTOR(10U) SMALL FIXED INDUCTOR(0.47U) SMALL FIXED INDUCTOR(0.56U) SMALL FIXED INDUCTOR(6.8U) FERRITE CHIP SMALL FIXED INDUCTOR(6.8U) SMALL FIXED INDUCTOR SMALL FIXED INDUCTOR SMALL FIXED INDUCTOR(82NH) FERRITE CHIP SMALL FIXED INDUCTOR(6.8U) SMALL FIXED INDUCTOR(220NH) SMALL FIXED INDUCTOR(100NH) SMALL FIXED INDUCTOR(68NH) FERRITE CHIP SMALL FIXED INDUCTOR(18NH) SMALL FIXED INDUCTOR(1UH) FERRITE CHIP SMALL FIXED INDUCTOR(3.3NH) SMALL FIXED INDUCTOR(15NH) AIR-CORE COIL FERRITE CHIP AIR-CORE COIL SMALL FIXED INDUCTOR(1.0U) AIR-CORE COIL AIR-CORE COIL

CP1 R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26 R27 R28,29 R100 R101 R102 R103 R104 R105,106

R90-0724-05 RK73GB1J154J RK73GB1J102J RK73GB1J100J RK73GB1J102J R92-1252-05 RK73GB1J102J R92-1252-05 RK73GB1J334J RK73GB1J102J RK73GB1J151J RK73GB1J473J RK73GB1J274J RK73GB1J151J RK73GB1J101J RK73GB1J103J RK73GB1J683J RK73GB1J104J RK73GB1J271J RK73GB1J473J RK73GB1J102J RK73GB1J104J RK73GB1J271J RK73GB1J124J RK73GB1J104J RK73GB1J681J RK73GB1J472J RK73GB1J102J R92-1252-05 RK73GB1J332J RK73GB1J123J RK73GB1J221J RK73GB1J102J RK73GB1J101J RK73GB1J332J

CF200 L1 L2 L4 L5 L6 L7 L8,9 L10 L11 L12 L14 L15 L16,17 L100 L101 L102 L103 L104 L105 L106 L107 L108 L109 L110,111 L112 L113 L114

J 1/16W J 1/16W J 1/16W J 1/16W J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W

13

TK-2107
PARTS LIST
TX-RX UNIT (X57-6020-21)
Ref. No. Address parts
R107 R108 R109 R110 R112 R114,115 R116,117 R119 R120 R121 R122 R123 R124 R125 R126 R127,128 R130-132 R133-138 R140 R141 R142 R143 R144 R145 R146 R147,148 R200 R201 R202 R203,204 R205 R206 R207 R208 R209 R210,211 R212 R213 R214 R215 R216 R217 R220 R222 R223 R225 R228 R229 R231 R232 R233 R234 R235 R240 R300 R301,302
New

Parts No.
RK73GB1J392J RK73GB1J152J RK73GB1J100J RK73GB1J331J RK73GB1J180J RK73GB1J473J RK73GB1J470J RK73GB1J472J RK73GB1J153J RK73GB1J473J RK73GB1J681J R92-1252-05 RK73GB1J561J RK73GB1J332J RK73GB1J681J RK73GB1J271J RK73EB2ER39K RK73GH1J154D RK73GB1J103J RK73GB1J473J RK73GB1J105J R92-1252-05 RK73GB1J331J RK73GB1J184J RK73GB1J104J RK73GB1J331J RK73GB1J100J RK73GB1J392J RK73GB1J184J RK73GB1J332J RK73GB1J153J RK73GB1J184J RK73GB1J104J RK73GB1J684J RK73GB1J272J RK73GB1J821J RK73GB1J330J R92-1252-05 RK73GB1J103J RK73GB1J271J RK73GB1J222J R92-1252-05 RK73GB1J122J R92-1252-05 RK73GB1J101J RK73GB1J102J RK73GB1J470J RK73GB1J471J RK73GB1J101J R92-1252-05 RK73GB1J224J R92-1252-05 RK73GB1J104J R92-1252-05 RK73GH1J913D RK73GB1J562J CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R

Description
3.9K 1.5K 10 330 18 47K 47 4.7K 15K 47K 680 0 OHM 560 3.3K 680 270 0.39 150K 10K 47K 1.0M 0 OHM 330 180K 100K 330 10 3.9K 180K 3.3K 15K 180K 100K 680K 2.7K 820 33 0 OHM 10K 270 J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

Destination

Ref. No. Address parts

R303 R304 R305 R306 R307 R308 R309 R310,311 R312 R313 R314 R315 R316 R317 R318 R320 R321 R322 R323 R324 R325 R326 R327 R328 R330 R331 R332 R333 R334 R335 R336 R338 R339 R340 R400 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R414,415 R416 R417 R418 R419 R420 R421 R422

New

Parts No.
RK73GB1J332J RK73GB1J105J RK73GB1J183J RK73GB1J124J RK73GB1J473J RK73GB1J103J RK73GB1J474J R92-0670-05 RK73GB1J123J RK73GB1J104J RK73GH1J474D RK73GH1J394D RK73GB1J274J RK73GH1J274D RK73GB1J184J RK73GB1J473J RK73GB1J223J RK73GH1J224D RK73GB1J104J RK73GB1J562J RK73GB1J104J RK73GH1J562D R92-1252-05 RK73GB1J102J RK73GB1J473J RK73GB1J222J RK73GB1J151J RK73GB1J474J RK73GB1J100J RK73GB1J563J RK73GB1J333J RK73GB1J473J RK73GB1J822J RK73GH1J124D RK73GB1J334J RK73GB1J104J RK73GB1J221J RK73GB1J181J R92-1252-05 RK73GB1J102J RK73GB1J222J RK73GB1J102J RK73GB1J104J RK73GB1J102J RK73GB1J822J RK73GB1J224J RK73GB1J100J RK73GB1J102J RK73GB1J473J RK73GB1J472J RK73GB1J100J RK73GB1J222J R92-1252-05 RK73GB1J102J RK73GB1J473J RK73GB1J272J CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R

Description
3.3K 1.0M 18K 120K 47K 10K 470K 0 OHM 12K 100K 470K 390K 270K 270K 180K 47K 22K 220K 100K 5.6K 100K 5.6K 0 OHM 1.0K 47K 2.2K 150 470K 10 56K 33K 47K 8.2K 120K 330K 100K 220 180 0 OHM 1.0K 2.2K 1.0K 100K 1.0K 8.2K 220K 10 1.0K 47K 4.7K 10 2.2K 0 OHM 1.0K 47K 2.7K J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W

Destination

J 1/16W J 1/16W J 1/16W J 1/16W D D J D J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W J K D J J 1/16W 1/4W 1/16W 1/16W 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

J 1/16W D 1/16W J 1/16W J 1/16W J J J J J J J J D J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W J J J J J J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

2.2K J 1/16W 0 OHM 1.2K J 1/16W 0 OHM 100 J 1/16W 1.0K 47 470 100 0 OHM J J J J 1/16W 1/16W 1/16W 1/16W

220K J 1/16W 0 OHM 100K J 1/16W 0 OHM 91K D 1/16W 5.6K J 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W J 1/16W

14

TK-2107
PARTS LIST
TX-RX UNIT (X57-588X-XX)
Ref. No.
R423 R424,425 R426 R427 R428 R429 R430 R431 R432 R433,434 R435 R500,501 R502 R503 R504 R505 R506 R507 R508 R509 R510 R511 R512 R513 R514,515 R516 R517 R518 R519,520 R521 R522 R523 R524 R525 R526,527 R528 R529 R530 R531 R532 R533 R534 R535 R536 R537,538 R539 R540 R541 R542 R548 VR1 VR500 VR501 S402,403 MIC50 D1-4
New Address parts

TX-RX UNIT (X57-6020-21)

Description
CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R CHIP R 47K 3.3K 8.2K 1.0K 2.7K 820 100 0 OHM 10K 15K 10K 4.7K 82K 6.8K 22K 6.8K 820 4.7K 1.0K 120K 3.3K 10K 1.8M 15K 33K 10K 1.8M 150K 33K 3.3K 1.8K 6.8K 51K 1.5K 15K 750K 18K 100 0 OHM 820 100K 1.8K 470 1.0K 100 J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W

Parts No.
RK73GB1J473J RK73GB1J332J RK73GB1J822J RK73GB1J102J RK73GB1J272J RK73GB1J821J RK73GB1J101J R92-1252-05 RK73GB1J103J RK73GB1J153J RK73GB1J103J RK73GB1J472J RK73GB1J823J RK73GB1J682J RK73GB1J223J RK73GB1J682J RK73GB1J821J RK73GB1J472J RK73GB1J102J RK73GB1J124J RK73GB1J332J RK73GB1J103J RK73GB1J185J RK73GB1J153J RK73GB1J333J RK73GB1J103J RK73GB1J185J RK73GB1J154J RK73GB1J333J RK73GB1J332J RK73GB1J182J RK73GB1J682J RK73GB1J513J RK73GB1J152J RK73GH1J153D RK73GB1J754J RK73GB1J183J RK73GB1J101J R92-1252-05 RK73GB1J821J RK73GB1J104J RK73GB1J182J RK73GB1J471J RK73GB1J102J RK73GB1J101J R92-1252-05 R92-0670-05 RK73GB1J472J R92-1252-05 RK73GB1J332J R12-7491-05 R12-7491-05 R12-7487-05 S70-0414-05 T91-0543-05 1SV283

Destination

Ref. No.
D5 D6,7 D100 D101 D102,103 D200 D300 D500 D501 D502 IC1 IC100 IC200 IC300 IC301 IC302 IC400 IC401 IC402 IC403 IC404 IC500 Q1 Q2 Q3,4 Q5 Q6 Q7 Q8 Q100 Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q200 Q201 Q202,203 Q300 Q302 Q304 Q305 Q306 Q307 Q400,401 Q402 Q403 Q404 Q405 Q406 Q407 Q408

New Address parts

Parts No.
1SV214 MA2S111 HSC277 HSK277 HSC277 HSC277 DA221 1SS372 DAN222 1SR154-400 MB15A02 NJM2904V TA31136FN NJM2902V NJM2904V TA7368F PST9140NR AT2408N10SI2.5 RN5VL45C M38267M8L241GP S-81350HG-KD NJM2100V 2SC4649(N,P) 2SC5108(Y) 2SK1875(V) 2SJ243 2SC5108(Y) UMC4 2SC4617(S) 2SC5108(Y) 2SC4988 2SK2596 2SK1824 FMMT717 2SK2595 2SK1824 DTC114TE DTC114EE DTA144EE DTA114EE 2SC4649(N,P) 3SK228 2SC4617(S) 2SK1824 DTC144EE 2SA1362(GR) DTC144EE 2SK1588 DTC114EE DTA114YE DTC144EE UMG3N UPA672T FP210 UMG3N DTA123JE

Description
VARIABLE CAPACITANCE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE IC IC(APC) IC(FM IF DETECTOR) IC IC(APC) IC(AF POWER AMP) IC(RESET SW) IC(8bit SERIAL EEPROM) IC(REGULATOR) IC(MPU) IC(VOLTAGE REGULATOR) IC(AUDIO AMP) TRANSISTOR TRANSISTOR FET FET TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET FET TRANSISTOR FET FET DIGITAL TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR TRANSISTOR FET TRANSISTOR FET DIGITAL TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR FET DIGITAL TRANSISTOR DIGITAL TRANSISTOR DIGITAL TRANSISTOR TRANSISTOR FET TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR

Destination

J 1/16W J 1/16W J 1/16W J 1/16W J J J J J J J J J J J J J J J J J J J J J J J J D 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W

J 1/16W J 1/16W J 1/16W J 1/16W J J J J J 1/16W 1/16W 1/16W 1/16W 1/16W

0 OHM 0 OHM 4.7K J 1/16W 0 OHM 3.3K J 1/16W

TRIMMING POT.(68K) TRIMMING POT.(68K) TRIMMING POT.(15K) TACT SWITCH MIC ELEMENT VARIABLE CAPACITANCE DIODE

2B

15

TK-2107
PARTS LIST
TX-RX UNIT (X57-6020-21)
Ref. No.
Q501,502 Q503 Q504 TH100 TH500
New Address parts

TX-RX UNIT (X57-588X-XX)

Description
TRANSISTOR TRANSISTOR DIGITAL TRANSISTOR THERMISTOR THERMISTOR

Parts No.
2SC4617(S) 2SC4919 DTA143ZE 157-503-65001 157-302-65801

Destination

Ref. No.

New Address parts

Parts No.

Description

Destination

16

TK-2107
EXPLODED VIEW
A B

24 23 B
1

25 8

8 1 B 18 26 12 F F SP F MIC

22

11 A 6

34 13 10 9 19

700 D 7 E
3

A M2.6x4 B NUT C NUT D M2.6x6 E M2.0x3.5 F M2.0x5

:N09-2319-05 :N14-0581-04 :N14-0582-14 :N30-2606-46 :N79-2035-46 :N83-2005-46

21
Parts with the exploded numbers larger than 700 are not supplied.

17

TK-2107
PACKING
C D

15.PROTECTION BAG (H25-0085-04)

14.PACKING FIXTURE (H12-3037-02)

21.BELT HOOK (J29-0624-03)

ANT. HELICAL ANTENNA (T90-0733-05):M3

16.PROTECTION BAG (H25-2012-04)

17.ITEM CARTON CASE (H52-1522-02)

3. CAP (B09-0351-03)

G. SCREW SET (N99-0396-05)

20.SP/MIC HOLDER (J21-4493-04)

18

TK-2107
ADJUSTMENT
Required Test Equipment
1. Stabilized Power supply
1. The supply voltage can be changed between 5V and 18V, and the current is 3A or more. 2. The standard voltage is 7.5V.

8. Oscilloscope
1. Measuring range : DC to 30MHz 2. Provides highly accurate measurements for 5 to 25MHz.

9. AF Voltmeter (AF V.M)

1. Measurable frequency : 50Hz to 1MHz 2. Maximum sensitivity : 1mV or more

2. DC Ammeter
1. Class 1 ammeter (17 ranges and other features). 2. The full scale can be set to either 300mA or 3A. 3. A cable of less internal loss must be used.

10. Spectrum Analyzer

1. Measuring range : DC to 1GHz or more

3. Frequency Counter (f. counter)

1. Frequencies of up to 1GHz or so can be measured. 2. The sensitivity can be changed to 500MHz or below, and measurements are highly stable and accurate (0.2ppm or so).

11. Standard Signal Generator (SSG)

1. Maximum frequency : 500MHz or more 2. Output : -133dBm/0.05V to 7dBm/501mV 3. Output impedance : 50

4. Power Meter
1. 2. 3. 4. Measurable frequency : Up to 500MHz Impedance : 50 , unbalanced Measuring range : Full scale of 10W or so A standard cable (5D2W 1m) must be used.

12. Tracking Generator

1. Center frequency : 50kHz to 500MHz 2. Frequency deviation : 35MHz 3. Output voltage : 100mV or more

13. Dummy Load

1. 8 , 3W or more

5. RF Voltmeter(RF V.M)
1. Measurable frequency : Up to 500MHz or so.

14. AF Generator(AG)
1. Frequency range : 100Hz to 100kHz 2. Output : 0.5mV to 1V

6. Linear Detector
1. Measurable frequency : Up to 500MHz or so 2. Characteristics are flat, and CN is 60dB or more.

15. Distortion Meter

1. Measurable frequency : 30Hz to 100kHz 2. Input level : 50mV to 10Vrms

7. Digital Voltmeter
1. Voltage range : FS=18V or so 2. Input resistance : 1M or more

Antenna Microphone

Speaker

PTT switch Monitor key Channel switch

LED indicator Power switch SP/MIC JAC

Use a non-conductive rod such as a Ceramic rod for adjustment (especially of trimmers and coils). Kenwood order No. A-0910 (0.4X0.9mm) Kenwood order No. A-1310 (0.4X1.3mm) TK-260 :K, K2

To protect the SSG,do not send out signals while adjusting the receiving unit. The indicated SSG output levels are for maximum output.

19

TK-2107
ADJUSTMENT
Adjustment point
L212

TC201

R225 TP2 TC1

TC201: L212: TC1: TC2: TP2:

Band-pass filter waveform adjustment AF level adjustment Transmit lock voltage adjustment Receive lock voltage adjustment Band-pass filter test point

TC2

Foil Side View

SP MIC CV

CH

VR501

IC403

MIC ANT

VR500

VR1

ANT: CH: SP: MIC: CV: VR500: VR501:

Antenna connector Channel selector Speaker jack Microphone jack Lock voltage adjustment terminal DQT waveform adjustment DEV adjustment

Componennt Side View

Note : To fine tune the frequency when not using a computer, adjust VR1.

ADJUSTMENT FREQUENCY LIST

Destination CH Center Low Hi TX f (MHz) 220.00 216.05 222.95 M3 RX f (MHz)

Coaxial antenna connector

Remarks
Connect the transceiver to the PC Send the channel data to the transceiver, then backup the data. Program the adjustment frequencies which are in the list, into the transciever. Note : Remember to reload the channel data you backed up after making the adjustments. JIG

1. Jig (chassis) for adjustment (part number A101392-03)

Relay terminal

2. Use the jig as follows:

1. Insert the coaxial antenna connector into the jig. 2. Place the unit on the jig and fix it with 12 screws. 3. Solder the antenna terminal to the terminal of the unit. Notes: Supply power from an external power supply.

UNIT

(
TK-260

Relay terminal: + jig (chassis) :

:K, K2

20

TK-2107
ADJUSTMENT
Use the KPG-55D programming software for adjustment of the next item in PC MODE (see page 3).

Squelch Level, Transmit frequency, DQT Balance, RF Power, QT Deviation, DQT Deviation, Battery Level

Section common to the transmitter and receiver (VCO)

Item 1. Setting 2. VCO lock voltage Condition 1) Power supply voltage Battery teriminal:7.5V 1) CH: TX high 2) CH: RX high 3) CH: TX low 4) CH: RX low Measurement Test equipment Terminal Parts Adjustment Method Specifications/ Remarks 0.1V 0.1V Check Measurement Test equipment Terminal Parts Tra generator ANT TC201 Spectrum analyzer TP2 SSG Oscilloscope AF. V. M Distortion meter ANT SP L212 Adjustment Method Adjust the frequency so that it becomes the spectrum waveform shown in Fig.1. Adjust to the MAX AF level more than 0.7V Specifications/ Remarks

Digital voltmeter

CV

TC1 TC2

3.8V 3.8V

Receiver Section
Item 1. Bandpass filter 2. AF level Condition 1) CH: RX center 2) Tra generator output -40dBm Connect the spectrum analyzer to TP2 terminal. 1) CH: RX center SSG output: -53dBm (501V) MOD: 1kHz DEV: 3.0kHz (Wide)

3. Sensitivity 1) CH: RX center CH: RX LO CH: RX Hi SSG ouput: -116dBm (0.35V) MOD: 1kHz DEV: 3.0kHz (Wide) 4. Squelch 1) CH: RX center Level MONI: ON (PC MODE) 2) Level 9 SSG output: -117dBm (0.32V) 3) Level 3 SSG output: -125dBm(0.126V) PC key

Check

SINAD: 12dB or higher

Level 9 Adjust to close the squelch.

The squelch must be closed.

Level 3 Adjust to close the squelch.

The squelch must be closed.

Transmitter section
Item Condition 1. Transmit 1) CH: TX center frequency PTT: ON (PC MODE) 2. DQT/QT 1) CH: TX center Balance (PC MODE) Measurement Test equipment Terminal Parts Frequency ANT PC key counter Modulation analyzer or linear detector (LPF: 3kHz) Oscilloscope Power meter Ammeter Modulation ANT analyzer or linear MIC detector (LPF:15kHz) Oscilloscope AG AF. V. M VR501 VR500 Adjustment Method Adjust to center frequency Specifications/ Remarks within 100Hz

Rectify the waveform to square wave

3. Power 1) CH:TX center (PC MODE) Battery terminal: 7.5V PTT: ON 4. MAX DEV 1) CH: TX center AG: 1kHz/120mV PTT: ON 5. MIC SENS 1) CH: TX center AG: 1kHz/12mV

Adjust it to 4.8W

0.1W 100Hz

Adjust it to 4.2kHz

Check 2.2kHz~3.6kHz: (+, - Peak whichever is Maximum) (Wide)

6. QT DEV 1) CH: TX center (PC MODE) QT: 67.0Hz

7. DQT DEV 1) CH: TX center (PC MODE)

TK-260 8. Battery :K, K2 1) Battery terminal: 5.8V Level (PC MODE)

Modulation ANT analyzer or linear detector (LPF:3kHz) Oscilloscope AG AF. V. M Modulation analyzer or linear detector (LPF:3kHz) Oscilloscope Digital voltmeter BATT

PC key

Adjust it to 0.75kHz

50Hz

PC key

Adjust it to 0.75kHz

50Hz

PC key

A d j u s t s o t h a t t h e L E D The LED must flashes. flash.

21

TK-2107
ADJUSTMENT
M3 BPF-Wave

Fig. 1

TK-260

:K, K2

22

PC BOARD VIEW
TX-RX UNIT (X57-6020-21) Component Side View

TK-2107

2 TX-RX UNIT (X57-6020-21) Component Side View

Ref. NO. IC100 IC302 IC400 IC401 IC402 IC403 IC404 IC500 Q103 Q104 Q106 Q107 Q108 Q109 Q304 Q305 Q306 Q307 Q402 Q403 Q501 Q502 Q503 Q504 D400 D401 D500 D501 Address 8F 8L 7Q 4P 8Q 6O 4R 6I 7E 8E 8H 8H 8I 8G 9M 8M 9K 9K 5Q 6Q 6L 6K 5G 4O 5C 5C 4H 5H
C417

R541
R536 C530 L502 R534 R539 R537 C527

J72-0686-02
4 1 R502 C503 CV

3
AF IC404 G I C410 C416

C531

C529 F500

R535

R538

C523

C502
Q504

C414 R540

IC401

R6

C422

R421

R423

C425

L500

R532

C525

R533

C526

R529

R417
SB

R530
D501

C522 C521 C520 R528

R525 C518

VHF

Q503

R416 R507

R401 51

R405
Q402 C407

D500

L401

R431

R430

C418 R414

6 10 CN400

5 1

C524

75 76
C516 R524

C408

50

D401 D400

R415 C420

C514

C519

1 4

IC500

8 C517
R516 C512 R519 C513

R511 R510
R515 C508

R508

R520 C507
C510

C505

C413 IC403
R506 L402 L400

C509 R514
C515

R409 C409
R412

Q403

R526

R521

C511

R527

R517

Q502 R542

DEV

Q501

100 1
R505 VR500

26

X400

R522

R512

R523

VR501

C412 L403 C415

C115
R126 R119 Q103

7
25
R413

R122

Q104

R500 C500 R501

C501 VR1

R418

C400
C403 R400

IC400 4 5 1 3 IC402 3 1 5 4

C337

R336

R335

R334 C335

C112

C334

Q305

R327
5 1

R330

Q107
R124

C127

R503 R504
BAL R548

C327

C504

R130

R131

R132

R404
C404

R408
R407

R411

C139

R518

R513

L118

C130

Q106

IC100

R138 C141

R145 R142

Q109

R144

R125

Q108

Q307

R140

D G

IC302

R310

R509
TH500

C533

R141

R143

R333

Q304

C134 R135

C132
R133 R134

R137

R332 C330 C332

Q306

R146
MIC

R339

R136

MIC500

10

C336

C333

R331

R531

C331

C411

10

M38267M8L241GP Component side Pattern 1 Pattern 2 Pattern 3 Pattern 4 Foil side

DTA114EE DTA114YE DTA123JE DTA143ZE DTA144EE DTC114EE DTC114TE DTC144EE 2SA1362 2SC4617 2SC5108
B E C

UMC4

2SC4988

FP210
B1 EC B2 C2

DA221

MB15A02 11

C1

12

13

23

24
14

TK-2107
TX-RX UNIT (X57-6020-21) Foil Side View
Q300

PC BOARD VIEW
TX-RX UNIT (X57-6020-21) Foil Side View
Ref. NO. IC1 IC200 IC300 IC301 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q100 Q101 Q102 Q105 Q200 Q201 Q202 Q203 Q300 Q302 Q400 Q401 Q404 Q405 Q406 Q407 Q408 D1 D2 D3 D4 D5 D6 D7 D100 D101 D102 D103 D200 D300 D502 Address 4E 8D 5B 7B 6F 4F 4I 4H 3H 5I 4I 4I 5I 6J 6K 7M 9C 9D 6H 9I 4B 4A 5Q 5Q 5M 5L 5N 6M 5O 5H 4H 4K 3J 4G 4J 3D 6I 7N 8N 8N 6I 9B 5P

D7

C15

R324 C302

C18

C1

3
C322 C321 C320 Q302 R326

C42

C40

C12

C36

R18

R1

R9

C24

R340

D5

Q5 TC1 D2 R22 Q7 C38

D4

L15 D3

R300

CP1

J72-0686-02
R15 L7 R17 Q2 R21 R20 C48 C34 R19 C30 543 L14

R27

R24

C31

R2

R29

C4

C45

C37

C44

C43

C49

R26

L11

IC1 C23 C7 R3

C5

C307

R303 C306 R317 C305

C6

C50

R433

R312

J500 R406 C424 C528 6 5 4 R419 R422 C421 R420 R425 R424 5 4 3 5 4 3 Q404 1 2 3 C430 4 1 2 Q407 1 2 Q406

L501

D6

R315 R314

C3

C41

Q8

R321

C309

C2

R328

11

10 C25

R28

C39

Q3

C35

C33

C316

C312

R5

TC2 L9

R434

C8

L10

R7

R10

R13

R16 C29

L6 D1

R426 R403 C406 Q408 D502 R402 R410 C402 Q400 Q401 L117 C147

R23

C46

R25

R322

R100 Q100

R101

5C C27

XOUT L2

C9 C14 TP2 L201

C100

Q405

L8

R104

C47

L100

C423 R435 R427 R428

R305

R105

R306

R338 R311

C300

C103

C304

R220 R225

R11

Q1

R8

L5

R308 R313

C218 C219

R112 C109 Q101 R108 R107 C108 R110

L103

R302 C301 C313 R301

R4 X1 C10 C20

C114

R307

14

1 2 3

20

L1

C32

C101

R103 C102

Q4 Q6

R102

IC300

C427 R432

L12

C429

L202 D Q202 G2 C222 R214

R223 D200 D100 C236 R106

R147 R148

Q102

L105 L104

R429

L106

C120

C123

C125

R12

R109 R116

R201

C303

L200 R211

C113

VC

GND

S R217

C104

G1 R216

C116 C122 R121 L107 C119 R117 TH100 C128 G S D C143 L110 L109

C220

R320

C107

C106

R114

C51

IC301

C201

C16 C221

C26

L16

C118

D101

C311

C205 8 C202 R202 C206 C207 R206 5 8

C28 1

L102 C237 C251 C245 R235

L112

C200

L17

C105

C110

L101

R115

R212 C235 C217 R215

R120

C131

C121 R128 C144 C133 R127 L115 C142 C138 L114 C146 C140

C308 R304 R309

C19

C17

R14

L4

Q105

S D C111

L108

C126

L111

XF200 IC200 C215

R325

C318

TC201

C314 R323

C338 C319

R222

C243

C203

L209

C212 16

R232

R203

C204 R204 R205 9

L204 R213

G1 R234 C254

D103

C208

D300

9
C209

Q200

C210 R207 C211 C225

D C250 R231

S S403

R240

C213

L203 R229 C248

CF200 Q201 C214 R210 R208 R200

R209

R228 C224

C246 R230

C532 S402

L212

10

D102

C257

C261

C137

Q203

C136

L210

R233 G2

C241

L208

L214

C259

R123

C135

R318

C129

L113

C124

R316

3SK228 11 Pattern 1 Pattern 2 Pattern 3 Pattern 4 12 Foil side Component side

2SK1588 2SK2596

UPA672T

2SK2595
S G S D

2SK1875

TA7368F

S-81350HG-KD

TA31136FN

AT2408N10SI2.5

NJM2100V NJM2904V

13

25
14

26

SCHEMATIC DIAGRAM

TK-2107
1

Note : Component marked with a dot ( q ) are parts of pattern1.

TK-2107

TK-2107

BLOCK DIAGRAM

31

32

RX section
-100dBm -103.5dBm -107dBm -107dBm -105dBm 113mVrms 185mVrms 23.5mVrms 0.63Vrms

-116dBm

-112.5dBm

5R

ANT

L114 Q203 IC200 R211

16 9 5 7 4 10

IC300 IC302 Q307

SP

XF200 Q201 C212 AF VR

C137 R224 L208, L209, L210 L203, L214 R210 1st Local 0.1Vrms IF 38.85MHz R217

Q202

RF center

AF 1kHz

SG output level for obtaining 12dB / SINAD when injected to each point through a 470pF coupling capacitor. Measure the 1st Local level on a RF VTVM.

Modulate the AF level with a frequency of 1kHz and deviation of 1.5kHz (Narrow), 3kHz (Wide). Then take the signal from the signal generator output when set to -53dBm and obtain the level shown on an AF VTVM when the AF output has been adjusted to 0.63Vrms with the AF vol.

TX section
120mVrms 0.16Vrms 0.17Vrms 0.53Vrms 0.62Vrms

LEVEL DIAGRAM

12mVrms

390mVrms

MIC C34 Q4 Q100 C100 Q6 C44

IC500

Q102 Q101 C104 Q105 Q105

9.0W ANT

C109

VR501 D5

C114

C116

AF VTVM

RF VTVM

Measure the audio frequency on an AF VTVM and radio frequency on a RF VTVM at high impedance. Set the MIC input obtain a moduration factor of 60% with the transmit frequency at center and a modulation frequency of 1kHz.

TK-2107

33

TK-2107
KNB-15A (Ni-Cd Battery)
KNB-15A CIRCUIT DIAGRAM
Discharge pin side

SPECIFICATIONS
Voltage Charging current Dimensions : 7.2V (1.2V x 6) : 1100mAh : 60.8W x 110.8H x 20.3D (mm) (projections included) Charger and charging time: KSC-15 (normal charger), approximately 8 hours Weight : 210g

Breaker (705C)

Breaker (805C)

Diode

Thermistor

Charge pin side

34

TK-2107
MEMO

TK-260

:K, K2

35

TK-2107
SPECIFICATIONS
GENERAL Frequency Range ............................................................. RF power output ............................................................... Number of channels ......................................................... Operating Voltage ............................................................ Temperature Range ......................................................... Dimensions and Weight with KNB-15A (7.2V 1100mAh battery) ........................ 216 to 223 MHz : M3 4.8W 16CH 7.5 VDC 20 % -30 C to + 60 C (-22 F to + 140 F) 58 (2-5/16) W X 125.5 (4-15/16) H X 35 (1-3/8) D mm (inches) 380g (0.83lbs)

KENWOOD CORPORATION 14-6, Dogenzaka 1-chome, Shibuya-ku, Tokyo 150-8501, Japan

KENWOOD SERVICE CORPORATION
P.O. BOX 22745, 2201 East Dominguez Street, Long Beach, CA 90801-5745, U.S.A.

KENWOOD ELECTRONICS CANADA INC.

6070 Kestrel Road, Mississauga, Ontario, Canada L5T 1S8

KENWOOD ELECTRONICS DEUTSCHLAND GMBH

Rembrcker Str. 15, 63150 Heusenstamm, Germany

KENWOOD ELECTRONICS BELGIUM N.V.

Mechelsesteenweg 418 B-1930 Zaventem, Belgium

KENWOOD ELECTRONICS FRANCE S.A.

13, Boulevard Ney, 75018 Paris, France

KENWOOD ELECTRONICS U.K. LIMITED

KENWOOD House, Dwight Road, Watford, Herts., WD1 8EB United Kingdom

KENWOOD ELECTRONICS EUROPE B.V.

Amsterdamseweg 37, 1422 AC Uithoorn, The Netherlands

KENWOOD ELECTRONICS ITALIA S.p.A.

Via G. Sirtori, 7/9 20129 Milano, Italy

KENWOOD IBERICA S.A.

Bolivia, 239-08020 Barcelona, Spain

KENWOOD ELECTRONICS AUSTRALIA PTY. LTD.

(A.C.N. 001 499 074) 16 Giffnock Avenue, North Ryde, N.S.W. 2113, Australia

KENWOOD ELECTRONICS (HONG KONG) LTD.

Unit 3712-3724, Level 37, Tower one Metroplaza, 223 Hing Fong Road, Kwai Fong, N.T., Hong Kong

KENWOOD ELECTRONICS TECHNOLOGIES(S) PTE LTD.

Sales Marketing Division 1 Ang Mo Kio Street 63, Singapore 569110

TK-260

:K, K2

36