Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 425 views

    Pirith Potha

    Uploaded by

    Amila Viraj Gunarathna
    This document provides specifications for an engine, refrigeration system, electrical components, and other parts. It includes details like: - The engine uses diesel fuel and has a low and high speed operation of 1625 rpm and 2425 rpm. - The refrigeration system uses R-134a or R-404a refrigerant and an oil type is specified. - Electrical components include a 12.5V DC control system, alternator, starter motor, and circuit breakers. - Standby power requirements and air switch settings are also listed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Pirith Potha

    Uploaded by

    Amila Viraj Gunarathna
    425 views3 pages
    This document provides specifications for an engine, refrigeration system, electrical components, and other parts. It includes details like: - The engine uses diesel fuel and has a low and high speed operation of 1625 rpm and 2425 rpm. - The refrigeration system uses R-134a or R-404a refrigerant and an oil type is specified. - Electrical components include a 12.5V DC control system, alternator, starter motor, and circuit breakers. - Standby power requirements and air switch settings are also listed.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides specifications for an engine, refrigeration system, electrical components, and other parts. It includes details like: - The engine uses diesel fuel and has a low and high speed operation of 1625 rpm and 2425 rpm. - The refrigeration system uses R-134a or R-404a refrigerant and an oil type is specified. - Electrical components include a 12.5V DC control system, alternator, starter motor, and circuit breakers. - Standby power requirements and air switch settings are also listed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    425 views3 pages

    Pirith Potha

    Uploaded by

    Amila Viraj Gunarathna
    This document provides specifications for an engine, refrigeration system, electrical components, and other parts. It includes details like: - The engine uses diesel fuel and has a low and high speed operation of 1625 rpm and 2425 rpm. - The refrigeration system uses R-134a or R-404a refrigerant and an oil type is specified. - Electrical components include a 12.5V DC control system, alternator, starter motor, and circuit breakers. - Standby power requirements and air switch settings are also listed.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3

    Specifications

    ENGINE SPECIFICATIONS
    Engine Fuel Type Oil Capacity: Crankcase & Oil Filter w/Bypass Oil Filter Oil Type* TK 3.74 No. 2 Diesel fuel under normal conditions 9 quarts (8.6 liters) 10 quarts (9.6 liters) Fill to full mark on dipstick API Type CF-4 or CG-4 or better API Synthetic type CF-4, CG-4 or better after first 500 hours Multigrade Oil Ambient Temperature SAE 5W-30 -22 to +86 F (-30 to +30 C) SAE 10W-30 -4 to +86 F (-20 to +30 C) SAE 10W-40 -4 to +104 F (-20 to +40 C) SAE 15W-40 +5 to +104 F (-15 to +40 C) 1625 25 rpm 2425 25 rpm 35 to 60 psig (241 to 414 kPa) 0.0079 in. (0.20 mm) 0.0079 in. (0.20 mm) Room temperature 14 BTDC 1706 psig (11720 kPa) 10 3 psig (69 21 kPa)shutdown 220 5.0 F (104 3 C)shutdown 180 to 190 F (82 to 88 C) 4 quarts (3.81 liters) with overflow tank 10 psig (69 kPa) Belts to compressor, fans, 12 V alternator, water pump and electric motor (jackshaft)

    Oil Viscosity*

    Engine rpm: Low Speed Operation High Speed Operation Engine Oil Pressure Intake Valve Clearance Exhaust Valve Clearance Valve Setting Temperature Timing Injection Pump Injection Nozzle Pressure Low Oil Pressure Sensor High Coolant Temperature Sensor Engine Thermostat Coolant System Capacity Radiator Cap Pressure Drive

    *Multi-viscosity weight oil with the recommended API classification may be used based on the ambient temperature. The above recommendations are written for mineral oil based lubricants.

    R-134a REFRIGERATION SYSTEM


    Compressor Model Refrigerant Charge Compressor Oil Charge Compressor Oil Type: R-134a (Solest 35) Suction Pressure Regulator Setting Special Setting MD-II Single Phase Heat/Defrost Method:Engine Operation Electric Operation High Pressure Cutout X214 8 lb. 5 oz. (3.77 kg) R-134a 66 oz. (1.95 liters)* TK No. 203-413 (Ester base) required 18 psig (124 kPa) 18 psig (124 kPa) Hot gas Hot gas and electric heater strips (Model 50) 325 +25/-0 psig (2088 + 172/0 kPa) Automatically reset @ 200 20 psig (1379 138 kPa)

    Specifications (Rev. 04/03)

    R-404A REFRIGERATION SYSTEM


    X214 7.5 lb. (3.4 kg) R-404A 66 oz. (1.95 liters)* TK No. 203-413 (Ester base) required 20 psig (138 kPa) 20 psig (138 kPa) Hot gas Hot gas and electric heater strips (Model 50) 450 +10/-25 psig (3103 +69/-172 kPa) Automatically reset @ 375 38 psig (2585 262 kPa) NOTE: Compressors are equipped with an oil filter. Every 2 years of operation or whenever there is a major service procedure performed, both the compressor oil filter and filter-drier must be changed. *When the compressor is removed from the unit, oil level should be noted or the oil removed from the compressor should be measured so that the same amount of oil can be added before placing the replacement compressor in the unit. Compressor Model Refrigerant Charge Compressor Oil Charge Compressor Oil Type: R-404A (Solest 35) Suction Pressure Regulator Setting Special Setting MD-II Single Phase Heat/Defrost Method: Engine Operation Electric Operation High Pressure Cutout

    ENGINE CLUTCHHILLIARD (Prior April 1997)


    Model Engagement Dynamic Torque TK No. 107-257 (Dwg. No. 5D44655G01) 900 100 rpm 66 ft-lb (89.5 Nm) minimum @ 1600 rpm

    ENGINE CLUTCHHILLIARD (Starting April 1997)


    Model Engagement Dynamic Torque TK No. 107-272 (Dwg. No. 2C21375G01) 600 100 rpm 66 ft-lb (89.5 Nm) minimum @ 1600 rpm

    BELT TENSION
    Tension No. on TK Gauge 204-427 New Belt Field Reset 75 3 70 3 72 3 67 3 55 3 50 3 55 3 50 3 1/2 in. (13 mm) deflection

    Engine/Compressor Compressor/Jackshaft (Electric Motor) Compressor/Evaporator Fan/Alternator Alternator/Evaporator Fan Water Pump

    NOTE: These are the original factory settings. Because it is difficult to use the TK gauge 204-427 in the field, adjust each belt to allow 1/2 inch (13 mm) deflection at the center of the longest span. NOTE: Belts should be tensioned cold and again tensioned cold after 10 hours of unit running.

    Specifications (Rev. 04/03)

    ELECTRICAL CONTROL SYSTEM


    Control System Voltage Battery Charging System Voltage Regulator Setting Alternator/Regulator Capacitor Alternator/Output Capacitor 12.5 Vdc 12 V 23 amp brush type integral alternator 14 V @ 70 F (21.1 C) 4.7 fd 50 Vdc 0.5 fd 100 Vdc

    NOTE: Disconnect components from unit circuit to check resistance.

    ELECTRICAL COMPONENTS
    Current Draw (Amps) Resistance at 12.5 Vdc (Ohms) 8.3 1.5 0.15 18 to 25 0.5 to 0.7 0.9 to 1.1 11 to 13 0.657 19 90 to 105 (cranking) 5.68 2.2 50 amp 5 amp (approx.) 2.5 (approx.) 8.5 amp (approx.) 1.5 (approx.)

    Glow Plug Fuel Solenoid: Pull In Hold In Pilot Solenoid Starter Motor Damper Solenoid DC Circuit Breakers High Speed Solenoid Electric Standby Reset Solenoid

    Electrical Standby Compressor Motors (Model 50 Unit Only)


    Horsepower Full Load (amps) Locked Rotor Amps Unit Full Load* Amps

    Voltage/Phase/Frequency

    Kilowatts

    rpm

    230/1/60 230/3/60 460/3/60 380/3/50 220/3/50

    5 5 5 4.2 4.2

    3.7 3.7 3.7 3.1 3.1

    1750 1750 1750 1450 1450

    18 14.4 7.2 7.3 12.7

    80 58 58 55 55

    25 21 12 12 12.7

    *w/Heater Strips Electric Heater Strips (Optional): Number Watts (each)

    3 750

    STANDBY POWER REQUIREMENTS


    Supply Circuit Breaker Extension Cord Size 30 amp/230 V 20 amp/460 V Up to 50 ft12 gauge 75 ft10 gauge

    AIR SWITCH
    Air Switch Setting 0.7 0.05 in. (17.78 1.3 mm) H2O

    You might also like